Super Bug TM-098 1st Printing
Super Bug (Atari (Kee Games), 1977) · Technical Manual · 44 pages · 23 sections · original scan
jenuey| d1AJag pue s aoueuajule|y ‘UOe10dCQ
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Super Gug
Operation, Maintenance and Service Manual
ATARI INC. 1265 BORREGAS AVENUE PO. BOX 9027 SUNNYVALE, CALIFORNIA 94086 408/745-2000 « TELEX 35-7488
° KEE GAMES a wholly ‘owned subsidiary
‘A Warner Communications Company fw}
All rights reserved. Copyright © 1977 by Atari, Inc. No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher.
For permission requests, write: ATARI INC. 1265 BORREGAS AVENUE P.O. BOX 9027 SUNNYVALE, CA 94086
8F Lithographed in the U.S.A.
TABLE OF CONTENTS
1 LOCATION SETUP
B. UNPACKING INSTRUCTIONS Examination for Shipping Damage . Mechanical Inspection C. INSTALLATION REQUIREMENTS FOR SUPER BUG™ .. Power Reguirements .. Temperature Range ... Humidity Range ....--....++++5 Location Space Requirements . Length and Type of Power Cord Interlock and Power On/Off Switches D. SELF-TEST PROCEDURE E. OPERATOR OPTIONS .... AWNHNNNNNKNNNN
2 GAME PLAY A. ATTRACT MODE .. B. PLAY MODE .. C. SELF-TEST MOD!
3 Kamran AND ADJUSTMENTS COIN MECHANISM Components on Coin Door . Access to Coin Mechanisms Cleaning of Coin Paths ... Lubrication ............ Adjustment of Coin Switch Trip Wire . Mechanical Adjustments on Coin Mechanism . General Troubleshooting Hints CLEANING ...... 0000 e eee eee ADJUSTMENTS ON TV MONITOR .. TV MONITOR REMOVAL FUSE REPLACEMENT .. LAMP REPLACEMENT .. STEERING PCB REPLACEMENT .. START SWITCH REPLACEMENT ..
4 THEORY OF OPERATION A. SUPER BUG GAME OVERVIEW .. B. SUPER BUG PCB OPERATION PCB Power ... Microcomputer ... Watchdog Circuit . Microcomputer Timing . Microcomputer Addressing ... Super L ug Alphanumerics Playfield : Audio . Super Bug Car Picture . N
ZO™MOOP
LIST OF ILLUSTRATIONS
Figure 1 Figure 2 Figure 3 Figure 4 Figure 5 Figure 6 Figure 7 Figure 8 Figure 9 Figure 10 Figure 11 Figure 12 Figure 13 Figure 14 Figure 15 Figure 16 Figure 17 Figure 18 Figure 19 Locations of On/Off, Interlock, and Self-Test Switches . 3 TV Screen During Play Mode ... 8 Coin Door Assembly .......... 10 Hinging Open the Magnet Gate Assembly 10 Removal of Coin Mechanism ............064+ 11 Surfaces to Clean Inside the Coin Mechanism Removal of Plate Covering Rear of Coin Slot ... Close-Up View of Lubrication Point Detail View of Coin Switch and Trip Wire Adjustments on Coin Mechanism ..... Locations of Adjustments on TV Chassis . Removal of TV Monitor ........ Removal of Fluorescent Lamp .. Block Diagram of the Super Bug PCB Printed Circuit Board Assembly ..... Power Supply Schematic Diagram Printed Circuit Board Schematic Diagram . Harness Schematic ... TV Monitor Schematic
LIST OF TABLES
Table 1 Self-Test Procedure Table 2 Operator Options .... Table 3. Points Required to Earn Extended Play
LOCATION SETUP
SUPER BUG is a one-player driving game developed by Kee Games. The game is packaged in a distinctively styled upright cabinet that rests directly on the floor. A 23-inch TV monitor is mounted in the top front of the cabinet, with the monitor viewing screen slightly tilted from the vertical. Playeroperated controls are mounted directly below the TV monitor viewing screen on the front of the game cabinet. The controls consist of a steering wheel, a four-speed gear. shifter, an accelerator foot pedal, a pushbutton for track difficulty, a start pushbutton, and a pushbutton for high score reset.
Two identical coin mechanisms are mounted on the lower front center of the game cabinet, below the steering and shifting controls. Either of these two mechanisms can initiate play. The cash box is located behind a locked access door below the coin mechanisms.
The player’s objective is to manipulate the Super Bug along the track in a race against time. The player must avoid sliding in oil pools in the road, or dropping into sand pits, as well as avoiding other cars, while keeping the Super Bug within the boundaries of the road.
Acceleration is as in a real car. Start out in anything but first gear and the car accelerates slowly. Once the car is moving, shifting into progressively higher gears increases the speed of the car. If the car goes into an oil slick or sand pit, it slides, with sound of sliding from the game cabinet speaker. If the car drives into a track boundary, a tree, or another car, a crash sound will be heard from the game cabinet speaker and the TV monitor viewing screen will flash.
B. UNPACKING INSTRUCTIONS
Examination for Shipping Damage Before shipment from the factory, components and subassemblies of each game are carefully checked for proper operation. However, during shipment some adjustments may have changed or parts may have shaken loose. Upon removing the game from the shipping container, first examine the exterior of the cabinet. Check for dents, chips, or broken parts. Then open the rear access panel and examine the interior of the cabinet. Any shipping damage, such as a dented, cracked or broken cabinet, or sub-assemblies broken or loose, etc. should be reported immediately to the shipperand to Kee Games.
Mechanical Inspection After determining that the game has been received in gocd condition, carefully inspect the interior parts and verify that:
- All plug-in connectors are firmly seated.
- The fuses are all seated in their holders.
- No harness wires have become disconnected or pulled loose.
- No loose foreign objects are present, especially metal objects that could cause electrical problems.
Be sure all major assemblies are checked. Check the game printed circuit board (PCB), the transformer, the two coin mechanisms, the speaker and fluorescent light, the player controls and the TV monitor chassis.
Do not go on to the remaining paragraphs of this section until the above mechanical inspection has been carefully completed. C. INSTALLATION REQUIRE. MENTS FOR SUPER BUG
Requirements for installation of Super Bug are listed in the following paragraphs:
Power Requirements Kee Games’ Super Bug is shipped ready to operate on 110 VAC, 60-Hz, single-phase, at approximately 200 watts.
Temperature Range Location and storage temperatures should not be below 0 degrees Celsius (32 degrees Fahrenheit) and no higher than 49 degrees Celcius (120 degrees Fahrenheit).
Humidity Range Relative humidity for location or storage should be no more than 95%.
Location Space Requirements Super Bug requires a minimum of 168 centimeters (66 inches) of vertical clearance, a minimum of 65 centimeters (25.5 inches) of width clearance, and 175 centimeters (69 inches) of depth clearance. Depth clearance includes 61 centimeters (24 inches) of player space.
Length and Type of Power Cord Kee Games has added a 1.83-meter (six-foot) strain-relief power cord to Super Bug. The advantage of the strain relief cord is that the cord will break off inside the game.
Interlock and Power On/Off Switches Kee Games has installed two on/off switches, as shown in Figure 1. To minimize the hazard of electric shock while you are working inside the game cabinet, an interlock switch is located at the rear access door. This switch completely removes all power from the game while the rear access door is open.
So that you can conserve energy, a power on/off switch has been added to the power circuit so you can turn the game off during closing hours. This switch is concealed above the accelerator foot pedal.
Please check for proper operation of the rear access door interlock switch by performing the following steps:
- Unlock and open the rear access door.
- Plug the AC power cord into a 110-volt source.
ON/OFF SWITCH SWITCH INTERLOCK SWITCH
Figure 1 Locations of On/Off, Interlock, and Self-Test Switches
- Set the power on/off switch to the on position by flipping the toggle switch toward the right of the game cabinet.
- Close the rear access door. Within approximately thirty seconds, the TV monitor should display a picture.
- Slowly open the rear access door until the TV monitor picture disappears. The TV monitor picture should disappear when the rear access door is opened to less than one inch at the top of the door.
- If the results of Step 5 are OK, then the interlock switch is operating properly. If the picture does not disappear as described in Step 5, check to see if the switch is broken from its mounting or stuck in the on position.
- Close and lock the rear access door.
D. SELF-TEST PROCEDURE Super Bug will test itself and will communicate with you that the game circuitry and controls are or are not operating properly. We suggest that you do the Super Bug Self-Test Procedure each time you collect the money from the cash box. All you need to do is follow the steps in Table 1. But first, please read the following explanation of the table.
Notice the three column headings of Table 1. The first column, Test Instruction, describes what you should do to make Super Bug test itself. Once you have performed each Test Instruction step, look at the picture on the Super Bug TV monitor and match that picture with the picture in the column labeled Results if Test Passes. Then, examine the TV Monitor picture and follow the instructions listed in the column labeled Results if Test Fails. Please note that some of the definitions are quite long.
if at any time you would like to start over again in the self-test mode, just set the Self-Test Switch to off, then again in the on position. This will begin the self-test mode at Step 1.
E. OPERATOR OPTIONS At this time it is best to select the game options most suited for your particular location. With the Self-test Switch set to the off position and Super Bug in the attract mode, the game may be set for the combinations of options you choose.
To set these options you must remove the Super Bug Printed Circuit Board (PCB) according to the following procedure:
- Unlock and remove the rear access door.
- Locate the RF shield in the lower right-hand corner of the cabinet.
- Remove five #6 x ¥-inch small pan-head Phillips screws from each of the long sides (total ten screws) of the RF shield assembly.
- Slip the Super Bug PCB out of the RF shield assembly.
- Set the switches for the desired options, as shown in Table 2.
- Reinstall the Super Bug PCB.
- Close and lock the rear access door.
- Verify option functions by playing the game.
All the options except Extended Play are selfexplanatory. Extended Play works like this: If a player accumulates the required number of points, the game adds 40 counts to the game timer. The number of points required for each option—liberal, medium or conservative—is a function of the selected game time option. This is explained in Table 3.
Table 1 Self-Test Procedure
Test Instruction
Set gear shifter to 4th gear position.
Unlock and open the Coin Door, Set
Self-Test slide switch (located inside and
to the left of the Coin Door) to the
‘on position:
Rotaie the steering wheel, first to the
right (CW), then to the left (CCW). Set gear shifter to Ist, 2nd, 34, then
4th gear. Press START pushbutton, then TRACK SELECT pushbutton. Trip right coin acceptor wire, then
left one. Close contacts of slam switch (lecated on upper inside of Coin Door above
door lock) TV Monitor displays the following in succession
o123456769RRCUE ALG ORSTU. Fencananressses Picture 2
Picture 1 Fenenasarenan?t
Fencnaos765a324 Picture 3 Picture 4 After the fourth picture, Super Bug motor sound will come on. This is the beginning of the next test, The motor sound will
remain on throughout the rest of Self-Test Results if Test Passes 7 Results if Test Fails Picture 1 and 2: Look for missing or incorrect numbers and/or letters on the top and bottom lines. Don't be concerned if display in center of monitor is different than what is pictured in the Results if Test Passes column. However, Super Bug should always be at the center of the monitor. Picture 3 and 4: In these pictures, focus your attention on one of the three playfield bands (a problem in one will almost always appear in the other two). Check the band to ensure that it is as pictured, Playfield Test Picture
In the fourth picture, a zero to the left of the letter Z, and/or a 1, 2, and/or 3 in place of the letters Z, Y, andior X, re spectively, indicates a faiture in the memory section of the Super Bug computer. If one or more of these are present, see the following for the failing memory. Q indicates a failure of RAM chip M1 andior N1 indicates a fail ROM chip D1 re of 2 indicates a fait ROM chip C1 3 indicates a fail ROM chip At re of re of Frocnase76sa%7) Memory Failure Picture
Motor Sound frequency increases when steering wheel turned to the right. Motor sound frequency decreases when
steering wheel is turned to the left Screech sound is present while shifter is in ist, 2nd, and 3rd gears, but not while in 4th gear (4th gear switches not used) Screech sound is present while each switch is pressed. Screech sound is present while each acceptor trip wire is
tripped. Screech sound is present while slam switch contacts are
closed. ao No change in motor sound frequency indicates a problem in the 9 of the connector to the Steering PCB (accessible through theCoin
Door). Constant screech sound, while shifter is in neutral or 4th gear, indicates that one af the eight switches is stuck Lack of screech sound indicates a bad harness wire or a bad harness connection. harness of the Steering PCB. Check to see if +5VDC is present on pin
Table 2. Operator Options
Switch Settings as labeled on:
| 8 | 7 | 6 | 5.4 | 3 | 2 | 1 | DIP switch | |||
| Option | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | schematic | Result |
| Game Cost | on on | Free play |
on off Two plays/coin off on One play/coin off off one play/two coins
| Game Length | on on | 60 seconds |
on off 90 seconds off on 120 seconds off off 150 seconds
| Extended Play | on on | None |
on off Liberal (easy to earn) off on Medium off off Conservative (hard to earn)
| Game Instruc- | on | on | English |
| tion Language | on off | French | |
| (as displayed | off on | Spanish | |
| on TV screen) | off off | German |
Table 3 Points Required to Earn Extended Play
Game Length Setting
| 60 | 90 | 120 | 150 |
| secs. | secs. | secs. | secs. |
Extended Play Points Required to Option Setting: Earn Extended Play
| Liberal | 90 | 140 | 190 | 240 |
| Medium | 100 | 160 | 220 | 270 |
| Conservative | 120 | 180 | 240 = 300 |
GAME PLAY
During use, Super Bug can be described as operating in one of three selectable modes: attract, play, or self-test.
A. ATTRACT MODE The attract mode begins when power is applied to the game. During this mode the monitor picture shows the highest score obtained by a player since the last power-up of the game. The words “GAME OVER" flash on and off. The roadway pylons, trees and road hazards move as if the car is moving along the road.
Figure 2 TV Screen During Play Mode
B. PLAY MODE The TV monitor display during the play mode is shown in Figure 2. During this mode, the TV monitor displays a roadway that advances when the accelerator foot pedal is pressed. Moving the shifter through the gears increases the advancing speed of the roadway. If the car comes in contact with one of the pylons, another car ora tree, the roadway pylons stop advancing, the TV monitor display flashes, and a crash sound comes from the game speaker. If the car drives into an oil spot or sand pit, a skid sound comes from the game speaker and the car appears to slide out of contro! until it passes through the hazard onto the roadway again.
C. SELF-TEST MODE This mode of operation is used by the operator to verify that the game is working properly. This mode is explained in the Installation part of this manual.
MAINTENANCE AND ADJUSTMENTS
Due to its solid-state electronic circuitry, this Kee Games unit requires very little maintenance and only occasional adjustment. Information given in this chapter and elsewhere in this manual is intended to cover most servicing situations that may be encountered at the game site. The procedures given are in sufficient detai! to be understood by a person with moderate technical ability. If reading through the manual does not lead to solving a specific maintenance problem, you can reach Atari's Customer Service Department by telephone Monday through Friday, between the hours of 7:30 a.m to 4:00 p.m. (Pacific Time). From inside California, call (408) 984- 1900; from outside California, call (800) 538-6892 (toll-free).
Ifyou are interested in gaining more information on video game technology, especially the electronics, we recommend reading the Video Game Operator’s Handbook, manual number TM-043. This book is available from Atari, Inc., Attn. Customer Service Department, 2175 Martin Avenue, Santa Clara, CA 95050 for $5.00 each, or from your distributor.
A. COIN MECHANISM
Components on Coin Door Figure 3 shows the back side of the coin door assembly where the game's two coin mechanisms are mounted. Included is the lock-out coil assembly; the lock-out wires are connected to this assembly but are hidden behind the coin mechanisms. During the attract mode the microcomputer energizes the lockout coil, causing the lock-out wires to retract far enough to allow genuine coins to reach the coin box. During the play mode and when AC power to the game has been turned off, the lock-out coil is deenergized, causing the lock-out wires to move out far enough to divert coins over to the return chute.
Siam Switch Assembly
Lock-out Coit Lamp Holder
Figure 3 Coin Door Assembly
Directly below each coin mechanism is a secondary coin chute and a coin switch with a trip wire extending out to the front edge of the chute. When the trip wire is positioned correctly, a coin passing down the secondary chute and into the coin box will momentarily push the trip wire down and cause the switch contacts to close.
Also shown in the photograph in Figure 3 is a slam switch assembly. It has been included to defeat Figure 4 Hinging Open the Magnet Gate Assembly any players who might try to obtain free game plays by violently pounding on the coin door to momentarily close the contacts on the coin switch. The slam switch contacts connect to the microcomputer system, which will ignore coin switch signals whenever the slam switch contacts are closed.
Access to Coin Mechanisms To remove jammed coins, and for maintenance cleaning, each magnet gate assembly can be hinged open without removing it from the door, as shown in Figure 4. Or, if necessary, each coin mechanism can be entirely removed from the door merely by pulling back ona release lever and simultaneously tilting the mechanism back, then lifting it up and out. This is shown in Figure 5.
Cleaning of Coin Paths
By talking to many operators, we have found that the best method of cleaning a coin mechanism is by using hot or boiling water and a mild detergent. A toothbrush may be used for those stubborn buildups
Figure 5 Removal of Coin Mechanism
of residue. After cleaning, flush thoroughly with hot or boiling water, then blow out all water with compressed air.
Figure 6 shows the surfaces to clean inside the coin mechanism. These include the inside surface of
Clean both surfaces where coin enters the mechanism, as well as the magnet.
Figure 6 Surfaces to Clean inside the Coin Mechanism
the mainplate, and the corresponding surface of the gate assembly. There may also be metal particles clinging to the magnet itself. To remove these particles you can guide the point of a screwdriver or similar tool along the edge of the magnet.
li coins are not traveling as far as the coin mechanisms, you will need to clean the channel beneath the coin slot. To gain access to this channel, use a %-inch wrench and remove all three nuts that secure the cover plate (refer to Figure 7). Removing the plate will provide access to the entire channel. Figure 7 Removal of Plate Covering Rear of Coin Slot
Also clean the inside surfaces of the secondary coin chutes, but when doing this be careful not to damage or bend the trip wires on the coin switches.
Lubrication Do not apply lubrication to the coin mechanisms. The only points that may need lubrication (and only rarely) are the shafts of the scavenger buttons {coin rejection buttons) where they pass through the coin door. Apply only one drop of light machine oil, and be positive that no oil drops down onto a coin mechanism. Figure 8 shows this lubrication point.
Manually hold down rejection button and apply one drop here.
Lock-out Wire
Figure 8 Close-Up View of Lubrication Point
Correctly adjusted trip wire
Figure 9 Detail View of Coin Switch and Trip Wire
Adjustinent of Coin Switch Trip Wire In order for a coin switch to operate reliably when a coin travels down the secondary coin chute, the rest position of its trip wire should be as shown in Figure 9, Use extreme care when handling or touching these wires.
Mechanical Adjustments on Coin Mechanism Coin mechanisms are adjusted prior to shipment from the factory and normally will retain these adjustments for many months. If, due to wear or other causes, it becomes necessary to make new adjustments, remove the coin mechanism from the coin door. Then take itto a clean, well lighted area where it can be placed in a vertical position ona level surface (such as a bench top). Besides a screwdriver you will need a set of several coins, including both new and old, worn ones. Figure 10 shows an exploded view of the mechanism and gives procedures for adjusting the kicker, separator, and the magnet gate. These adjustments should only be done by someone who has experience in servicing coin mechanisms and who understands their operation.
General Troubleshooting Hints The first action is to look for jammed coins. After these have been removed, examine the coin path for presence of foreign material or loose objects (such as chewing gum, small metallic objects, paper wads, etc.). In cases where game usage is heavy, it may be necessary to clean the entire coin path periodically, in order to prevent build-up of contaminants that can hinder the movement of coins through the mechanisms. Also confirm that the trip wire on each coin switch is intact, and is properly adjusted. If troubles still persist, check the conditions and positions of the lock-out wires, and the mechanical! adjustments on the coin mechanisms, before suspecting the electronics. If a coin mechanism rejects genuine coins, try to readjust it. If this is not successful, then replace it with a working mechanism.
B. CLEANING The exteriors of game cabinets and Plexiglas® panels may be cleaned with any non-abrasive household cleanser. If desired, special coin machine cleaners that leave no residue can be obtained from your distributor. Do not dry-wipe the plex panels because any dust can scratch the surface, thereby fogging the plastic.
C. ADJUSTMENTS ON TV MONITOR
The TV monitor need be adjusted only when the picture is distorted or if the contrast or brightness seem out of adjustment.
The monitor's adjustments function like those of aconventional commercial television set, except that the volume adjustment has no effect. Instead the game produces its sound in circuits separate from the TV monitor. Figure 11 shows the location of the adjustments on the rear of the chassis. When making the adjustments, follow these general guidelines:
BRITE (Brightness)—Perform this adjustment before the contrast. Adjust so that the white lines covering the screen just barely disappear, when the brightness is turned up.
CONT (Contrast)—Adjust so that the images are as bright as possible against the dark background without being blurred.
ITEM IDENTIFICATIONS 1 Kicker and Separator Screws 2 Washers 3 Kicker 4 Separator 5 Lever Spring 6 Gate Pivot Pin T Mainplate Assembly “C" washer Rail Gate Assembly Cradle Assembly
18 Upper Gate Pivot Spring 14 Undersize Lever Assembly 15 Magnet Gate Assembly 16 Magnet Gate Adjuster 17 Retaining Screws 18 Coverplate Assembly 19 Return Cover 20 Coverplate 21 Mounting Studs 22 Lower Gate Pivot Spring 23 Coin Release Lever
Kicker and separator 1, Set the acceptor with the back of the unit facing you in the test position.
- Loosen the kicker and separator screws (1) and move the kicker (3) and the separator (4) as far to the right as they will go. Lightly tighten the screws.
- Insert several test coins (both old and new) and note that some are returned by striking the separator. 4, Loosen the separator screw and move the separator a slight amount to the left. Lightly retighten the screw.
- Insert the test coins again and, if some are still returned, repeat Step 4 until all the coins are accepted.
- Loosen the kicker screw and move the kicker as far to the left as it will go. Lightly retighten the screw.
- Insert the test coins and note that some are returned.
- Loosen the kicker screw and move the kicker a slight amount to the right. Lightly retighten the screw.
- Insert the test coins again and, if some are still returned, repeat Step 8 until all the coins are accepted.
- Be sure that both screws are tight after the adjustments have been made.
Magnet gate 1, Set the acceptor with the front of the unit facing you in the test position.
- Turn the magnet gate adjusting screw (16) out or counterclockwise until none of the coins will fit through.
- With a coin resting in the acceptor entrance, turn the adjuster in or clockwise until the coin barely passes through the magnet gate.
- Test this adjustment using several other coins (both old and new) and, if any fail to pass through the magnet gate, repeat Step 3 until all the coins are accepted. 5, Fix the magnet gate adjusting screw in this position with a drop of glue.
Additional Cleaning
- Remove the transfer cradle (12) and the undersize lever (14).
- Use a pipe cleaner or similar effective cleaning tool to clean the bushings and pivot pins.
- Replace the transfer cradie and the undersize lever.
- To be certain the coin mechanism is completely free of any residue, place the mechanism in a solution of boiling water and mild detergent for several minutes. Carefully remove it and let it air-dry completely before reinstalling in the door.
Figure 10 Adjustments on Coin Mechanism
FUSE (5A quick bow) FUSE. (24 quick stow) as comnnst Cvenr, vert. uN. BRIGHT. HEIGHT Honiz. How) \_verr HOLD VOLTAGE SWITCH (leave In right position)
TEC MODEL TEM-600/TM-623 rons comaast=}—\ Camentntas WORIZ, 086 rocus
MOTOROLA MODEL M5000/M7000
Figure 11 Locations of Adjustments on TY Chassis
HORIZ OSC. (Horizontal Oscillator)—Adjust if the picture is slightly off-center horizontally, if the images appear warped, or if the picture is broken up into a series of diagonal lines. Adjust for a stable, centered picture.
D. TV MONITOR REMOVAL If the TV monitor proves to be at fault, remove the monitor as shown in Figure 12.
E. FUSE REPLACEMENT Super Bug contains four fuses, two on the power supply assembly and two on the TV monitor assembly. These fuses are all easily accessible through the rear access door. Replace fuses only with the same type of fuse as follows:
TV Monitor Fuses—3AG 1-amp slow-blow, 250 volts
Power Supply Fuses—3AG 2-amp slow-blow, 250 volts
F. LAMP REPLACEMENT Super Bug contains an eighteen-inch fluorescent lamp inside the top of the game cabinet assembly. To replace the lamp, remove the screws from the top Plexiglas retainer, as shown in Figure 13. Lift the attraction panel Plexiglas up and out of the bottom Plexiglas retainer. Replace the fluorescent tube. Replace the attraction panel plex, and the top plex retainer.
G. STEERING PCB REPLACEMENT If it becomes necessary to replace the steering PCB, use the following procedure:
- Unlock and remove the rear access door to the game cabinet.
- Unplug the 10-pin Molex connector from the steering board PCB.
- With a 7/16-inch wrench, remove the self-locking hexagonal nut and %-inch internal tooth starlock washer from the steering wheel axle screw, while a helper holds the steering wheel at the front of the cabinet.
- Remove the black plastic edge-toothed wheel.
- Remove the steering PCB by removing two panhead #2-56 x %-inch Phillips screws and lifting the board out.
UNPLUG MOLEX CONNECTOR FROM BACK OF MONITOR CHASSIS
Figure 12 Removal of TV Monitor
- Before installing the replacement steering PCB, be sure there is a sufficient amount of silicone lubricant on the inner hole of the black plastic edgetoothed wheel.
- Install the replacement PCB by completing steps 1 through 5 in reverse order.
H. START SWITCH REPLACEMENT The START pushbutton switch is backlighted by two parallel-wired #47 lamps. The switch itself is a Cherry Switch with gold-plated contacts. To change a START pushbutton, reach in through the coin door and squeeze both sides of the switch and pull out. Replace switch with Kee Games part number 062-020 switch.
To replace START switch lamps, reach in through the coin door and loosen lamp mounting screws. Remove lamps and replace with #47s. PLEX RETAINER
PLEXIGLAS
FLUORESCENT LAMP.
Figure 13 Removal of Fluorescent Lamp
SQUEEZE, THEN PUSH THROUGH
Figure 13A Removal of Start Switch
THEORY OF OPERATION
A. SUPER BUG GAME OVERVIEW Electronically, the Super Bug game consists of a power supply, a TV monitor, a game printed circuit board, and a speaker. Electrically, the Super Bug game consists of a control panel and foot pedal, a coin door, and a fluorescent lamp.
The controlling part of the game is the game printed circuit board (PCB). Since the PCB interfaces with all the assemblies, excluding the fluorescent lamp, the following description of the Super Bug game operation relates primarily to the PCB.
‘ADDRESS c ADDAESS E N A
L E
ENABLE
DATA PLAYFIELD
DanDoor pAbS ADDRESS DATA HORIZONTAL, at
DATA
ENABLE
ADDRESS
STEERING
ACCELERATOR ENABLE ouTPuT PORTS _______ ADDRESS » Tow MONITOR.
ALPHA NUMERICS —
SCREECH
To > SPEAKER,
Figure 14 Block Diagram of the Super Bug PCB
B. SUPER BUG PCB OPERATION The PCB has a microcomputer designed and programmed to perform the functions of the Super Bug game. Figure 14 is a block diagram of the PCB.
For easy reference, the PCB is divided into 130 sections (see Fgure 15 for the game’s PCB assembly). These sections are identified by letters A through P (skipping letters G, |, and O because they may be easily confused with numbers 6, 1, and 0, respectively) across the short side of the PCB. Sections are identified along the long side of the PCB by numbers 1 through 10. The letters and numbers create a grid, andall IC’s are located on the PCB along the grid lines. For example, to find the main horizontal motion counters N5 and N6 which are shown at the top center of sheet 1 of the schematic, look along the short side of the PCB to letter N, then down the long side to numbers 5 and 6. The two counters are located at the intersection of line N and lines 5 and 6. At location M/N/P-10 is an LM323 regulator mounted in a large black heatsink, and a 2-ohm, 20watt resistor. These components produce a good deal of heat during normal operation. The temperature is not extreme, but touching sensitive skin may produce a burn.
Another item we would like to bring to your attention is power distribution on the PCB. On the top of the PCB, most of the wide traces are DC ground. On the back of the board the wide trace along the long end of the board in +5 VDC.
PCB Power The PCB receives its power from the power supply in two voltage levels: 16.5 VAC and 25 VAC (see Figure 16). The 16.5 VAC is rectified off-board and regulated by an LM323 to a stable +5 VDC. The +5 VDC is distributed throughout the board to power all circuits except the audio output. The 25 VAC input is
othonanuguent duegemneneT
mattatt 90-600! LU mall
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL Reproduction forbidden without the specific writien permission of Atari, Ine. Sunayale Calitornia. This drawing is only consitionally issued. and neither receipt not possession thereat conters or teansters ‘any right in. or license 10 use, the subject matter of the drawing oF any design oF technical iformation shown thereon, nacany right to reproduce this drawing or any part tereot, except for manutacture by vendors of Alar Incor ted and for manufacture under the corporation s writ ten license. no rghtto reproauce this drawings granted or the subject matter thereot uniess by written agreement swith or written permission from the corporation. areal VERSION
oe ass ae as!
Figure 15 Printed Circuit Board Assembly iro 2002-06
= ——— eee Item | Part Number Description Tem | Part Number Description (00777901 1 [P.c. Boara 3 2a-101103, tap., Hylar, .ola® 1000 car 2 10-5102 13 |Res., Carbon, 58, WH, 1K OM RI,2/4,5,21,25,26,31,37, 27 24-250225 * Electrolytic, 2.206 25¥ 27 28,59, 65 ,69 26 24-250106 . . qows “= cz0 3 do-s103 27 10K R12-20, 32,34, al, 43 go | asu027 * 7 Sone ees
45-50, 53-57 , 66 68 . . rovous * = c28
© Pe © RL a700ue™ 33
RO 30 24-250108 31 24-250478 32 27-250224 3 27-250102 34 27-250103
10-5104 10-5105 ” Ceramic Disc .22uf * 30 ” "Jools 36 . "ome 22,31, 32,39
35 27-250104 5 . clue" cl-19, 24-26, 29 R7 34, 35, 38, 40
Re 36 | 2e-101221 aif Dipped Mica, 220pf 100 C37
R22, 23, 52 es Raz a8 Ra -
10-5162 " hm Lek" R5B,60 R3, 64 10-5222 | R27, 30 |
7 10-5271 10-5224 10-5225 10-5331 2 | 10-5233 aa} 10-5392 | 14 | 10-5335 as | 10-sa71 ie | 10-sa72 2 | 10-sa7a ie | io-sea3 ia | 10-sazz 20 | 19-318502 zi | 19215254 22 | 19-ep 9W2P0 Ril 40 a1-n14P 2 || piode, arar cr2, 3 R24, 36, 39 a 31-1914 a || picde, 1w914 cal
R35, 4a RG an R10 44 R29 45 s3-2N3604 a|| transistor, 203644 on ‘rimpot 5K ORM R63 | 46 34-7E3300 1 MJE3300 rey Trimpot 250K Om Rez a 35-mca106-1 2 || sor McRLO6~1 oa, 5
Res., Wirewound 208, 2 OHM R61 a 23 4a 25 51 37-7400 4 Intergrated Circuit, 7400 Pl, LS, M9, PY, 52 37-7402 4 7402 Ka, J8, KB, B9, 7404 AZ, B2, C2, D2, ca, NT, NB 7408 Ha, PT, CB, HB, NO . aro #3, 33, m8 . yaa J4, 37 ” 7414 R10
© store commircaran cone, 33 37-7408 8 34 37-7408 35 37-7410 56 37-7411 57 37-7414 38 37-74L814 59 37-7420 74us14. 10 " 7420 Pe " 7437 Ba, BS
60 37-7437 61 37-7402 1 . 7442 D7
—_—_— sees PARTS FIST SPECIFICATION Page 4 of 4
LIST SPECIFICATION
Teen Pare Number Description
37-7476 a-7486 37-7436 37-7492 37-749 37-7415 37-7413 37-74164 y7-74174 a7-74175, 3774192 37-74109 gr-91€ vont 37-9322 79028 37-e197 37-555 37-1323 37-"pA1004 62-001 o6-11sP1T 72-16080 75-016 75-056 75-936¢ Je-06001 7-060 22 Tntergra Regulator op-aNe: Switch, Switch, serews, washer, Washer, tea Civeuit 7474 " 7496 " 7496 ~ 7492 " 7495 . mais . 74153 " rales . 4i% " 74095 ” pa121 " 74109 " ene 9921 " 922 eres 4, PS 07 47,0908 X4,I5,15,39, ba aT 13, HS £9, Po 6, x B10, C10 a, x9 5 /M6,08,09 05, 05,£8,78, M4,N4,N5,K6, 87 P2, PA, X5, J6/L5,E7, F7
83, Fa M2, NZ, DB, DALO04 ALO SPST, Momentary SPSt x © Dip Pan Ba., Phil., 6 Flat #6 siz SWI 32h Lg. Cres
Lock, Int. Star #6 wut, Hex #€-22 Cres
Heatsink (19323) Heatsink (TDALOOS) Part Number Qty. Description OO ee aie un a2 us a6 rr ne ap a2. 7a-13016 78-16005 79-42040 79-42118 90-102 90-6002 90-7002 90-7013 009471 009472 ooe114 oooia1 009122 009123 09124 02125 09126 009127 WR Cement (TDAI0O4 Heatsink) silpad (LM323) Socket 40 Pin, Med Insertion
Socket 18 Pin crystal, 12.096 MHZ Intergrated Circuit Tatergratea circuit Intergrated Circuit Super Bug Alpha-Number Prom "Playfield Prom 3 Super Bug Syne Prom Super Bug Program Rem 1 Super Bug Alpha-tumber Prom super Bug Car Picture Prom Super Bug Playfield Prom super Bug Playtield Prom 2 cs M3,N3, FS, HS ML,NL,E6,PS Na HS Ms bh el al M3 x6
TRANSFORMER PCB A00L555-O!
| eee | £'T | Sl ac.co0.uf | ||||||
| i | | | 2, | 4 | |||||
| Y | 220 | OR | wr | VY St | ev aed] | ||||
| vt | : | Vyi | get | |||||
| VOTRE | _YiBK|_205V | ces vac | | Ie gd gi | +L | Rexle | |||
| SELECTION | ily | Tr | 5 | cT | 4oy | ine ae S| | chu | 3 |
| BLOCK | | | & | ||||||
| e5OWN | 2 | | op | 1 | ia | wi | oR | |4 | |
| OR] | [3lw | _ | iB | l | i | w | |S | |
| | | [4[BNw | eS ae | | PiU | on | |e | ||||
| | | 5|BN | ¢ | Vy | 5 |
me =| POWER i a ||P
| — | 2 | i | PCB | |
| = | 5 | 0 | ||
| Sv | 2le | &.3Vv | au | thy |
| Our | HEN | AC | | | |
| ~ | 3 | Bo) | Bu | liz |
| aa | j | : | ||
| oN | I | — |
ES —4
| nsVv | I | iON | |
| out | 2|ON | 7 | |
| 3 |W | KAW | Te | TP |
—_ INTERLOCK SwiTCH
| Fuses | Ww | || | i Wo | Sw |
| ~ | BK E | BK |X 1 BK | ||
| r | 3 | Co | ||
| w_ | {3 | 2 | ° TP | ON/OFF SWITCH | |
| spur | en | [2 | BKiw |* | t Bewl 1 BK |
| BK [i | wiBk |? | wer! A Iw | ||
| LI | GN 1 | are |
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL Reproduction lordidden without the sion 0! tan, Inc. Sunnyvale is only eanivonally sued, an
f manufacture by vendors of Atari incor thereat, excep! porated and for manulactute under the coxporation 5 writ fenlicense, no rant to repraduce this drawings ranted or Ine subject matter thereol unless by agreement with OF weilen permission from the cos
Figure 16 Power Supply Schematic Diagram
rectified through CR2 and 3, filtered by capacitor C33, and supplied to the audio output as unregulated 18 VDC.
The +5 VDC regulated voltage is also supplied through 1K pull-up resistors R1, R2, R4, R5, R21, and R25 for floating or unused inputs. Pull-up voltage is labeled P on the schematics.
Microcomputer The microcomputer consists of the Read-Only Memory (ROM), Random-Access Memory (RAM) used as scratchpad memory, and the microprocessor (see Figure 17). The microprocessor controls the microcomputer through a 16-bit address bus which addresses the ROM, RAM, playfield logic and audio circuits. An 8-bit bi-directional data bus provides a path for transferring data between the microprocessor and the various memories, the switch circuits and the playfield logic. A special watchdog circuit makes sure that the microcomputer functions properly.
Watchdog Circuit The watchdog circuit is a shift register, a 5-bit twisted-ring counter. In normal operation, the circuit is pulsed once each TV picture frame by the processor, resetting the counter. If five frames occur without a pulse, the counter resets the microprocessor to restart. This prevents random electronic static from upsetting game operation. The power-on hardware, or the PCB reset pushbutton, presets the counter, which in turn initializes the microprocessor and starts the attract sequence.
Circuitry Timing Clocks for the PCB originate from a 12-MHz crystal-controlled oscillator. The oscillator is divided by two to develop two 6-MHz clocks, designated on the schematic as 6 MHz and 6 MHz. The horizontal counters are driven by 6 MHz, which provide the horizontal synchronizing pulses 1H through 256H. The signals HBLANK and HSYNC are developed in flip-flops L7. HSYNC is the clock input for the vertical counters which provide the vertical synchronizing pulses 1V through 128V. VBLANK and VSYNC are developed by a special coded ROM, M6.
Microprocessor clocks $1 and Qare developed by dividing 2H by two in flip-flop F4. Inverters E4 provide the necessary voltage levels.
Microcomputer Addressing The address lines (BAO through BA15) are buffered to eliminate signal loading. The lowernumbered lines (BAO through BA9) address the program memory ROMs (E1, E2, H1, H2, and K1, K2). The scratchpad memory (RAM N1 and M1) are addressed by address lines BAO through BA8.
The higher-numbered address lines (BA10 through BA15) address the address decoders. The address decoder output enables the appropriate memory or logic device.
The LEGIT signal is developed from the phase 2 clock and occurs one-half clock period after the phase 2 clock rises. This signal is used to strobe the TTL and is delayed from the clock to allow the data lines to settle. The VMA signal is an output of the microprocessor which only exists when the microprocessor wants a data transfer. VMA enables the ROM address decoder and is part of the input to develop the System Enable signal.
Super Bug Alphanumerics Alpha characters and numerics are stored in ROM M3, N3. Each character is traced in a block 16 lines square, at the top of the display on the TV monitor. The PROM inputs are vertical functions 1V, 2V, 4V, 8V, horizontal functions 4H and 8H, and the output of alphanumeric RAM P3. Address lines BAO through BA4 address the desired character. Lines BA8 and BA10, with SYS EN (System Enable) enable the RAM for writing. Chip P3 is a 128 x 8 RAM which operates with the microprocessor, accepting data through tri-state buffers M2 and N2. The output of M3 is converted from 4-bit parallel to serial output and clocked out to the video summing gates through shift register 13.
Playfield The playfield logic is similar to the alphanumeric, although more complicated. The ROM consists of three ICs €5, F5, and H5. To permit rotating the playfield, separate horizontal and vertical counters (C5 and E8, D5 and F8, respectively) are used. These counters can be offset by the processor to create field rotation.
Cs E6 and F6 are the playfield RAM. They are loaded through tri-state devices D6 and H6, which are connected to all eight lines of the data bus. The RAM output accesses ROM pictures and controls the various shades of gray used to make the picture on the TV monitor. There are 48 playfield objects; objects 0 through 7 are things you slide on (oil and sand), objects 16 through 47 are things you crash into (trees,
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
an= wok
eo1
ATTRACT #4 £02 | epa sleds wr tel a ea ef, 8? dy Maas at ao re 1918 i ase a ts a
asa
sie
= | CRASHY
CRASH
CRASH 3
cRASHS =),
- Det gah wees Teia OV pPo to aay
era —4ip rafe » val? ve Te CRS pe RPS TMD Zal’t —_ crasne shi 2a [S—— cRAsHa 5)
[——crasna ATTRACT 475
Lal stant Lae subro,
Aveo ous
NOTICE TC ALL PERSONS RECEIVING THIS DRAWING: CONFIDENTISL Reproduction lorbrédue wuthout the specie wnitien permission of Atari, ine, Sunnyvale Cablozaa This drawing 1s only conaiianally 1esuec. and either receipt nox possession thereat canters or ansters, any night im, oF license to use the subject matter ot the Beaming er any design oF lechnveal information shown Inerean norany right tereproduce this crawing orany part theo! except Yor manutacture by vendors oF Aan Ineo porated and for manutaciure under the corporaven s wil ten license, ne right to reproduce nis drawings granted ot Ihe Sutzeet matter thoraol unless by wntten agreement ‘wilh or wniten permission from the Corporation
Figure 17 Printed Circuit Board Schematic Diagram
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
Boe CRASH RESET
a eve ae
| rd | a2 | ou, | #2 |
2 = = Ed
B0S .
ave an as Bae -O2 VERSION —+ ‘sen
| - | ple | fs dab Is |
a a] a
| Z | en | ees | fe | be | 2 | a | * | |
| 008s | loosava| | [odtite | [osseeal | | 05507 | | dsb cal | bas | 2009121 | | oo5N22| | epr23 | ||||
| bg | ony | 3 | e | |||||
| fi | “ | ey | : | i | ||||
| 4 | he | Bas | a | A | ||||
| 4 | ie | ss | a | |||||
| 4 | ms | tes | ——? | es | ||||
| 2 | sg | eas | —— | no | ||||
| i | ne | a | 8 | |||||
| 3 | one | a | ||||||
| ey | eo) | ——# | 7 | |||||
| es | ape | ra | loz | |||||
| cera) | [era | cet | aw) | [ec | ae | ees | 3 | es |
| fer | ree | FF | us | fs | ||||
| A | 7 | se | re | | BD? | 4 | |||
| id | +s¥ | sv | +5V | +5 | ||||
| fie | fa | le | is | |||||
| er | Fi | Gi | a | ig | ot | |||
| sjoosiia | |eckaes| | |oosus | lossaee| | C9120] | oca¢u7 | Pra | ||||||
| “| | re | ce | —ae | |||||
| 7| | az | a | ||||||
| Li | AS | 13) | ra | |||||
| 3 | S| | ee | cen | |||||
| ; | ae | 5 | NOTICE 70 ALL PERSONS RECEIVING TS DRAWING | |||||
| i | a7 | wes TEE | ce | CONFIDENTIAL Reproduction forbrdden without the | ||||
| r | 4 | Jow, | E | specitic written permission ol Atari Inc, Sunnyvale | ||||
| RT | : | ews] | ter wal | [ee | aw | {ereot except for manulacture by vendors ot Alar Ineor |
[2 i ie gy cee [s. Jt i Pe a J ry porated and for manuracture under the corporation $ weit fen license. no right 1o reproduce his drawing is grarted or the subject matier thereof unless. by watten agreement wath or written permission trom the corporation
Figure 17 Printed Circuit Board Schematic Diagram
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
a ae ov kt hes 1s) ne 5a: PO
| . | oa | 1 | fz | ——4 | CAR VIDED |
| vs eb? | = | ev | e| |
pag |
| fe | ohpye | AN | ente | z| |
| 95 asf | son | vives | ons | 4 |
| ress ott | 24 | cue | 4 |
vallins cet
sax e acmR_= Pu ° mE he > mr? oR Bs. ¢
> es a
| wav | —= | : |
aav ee
| ed | 2 | aa | 1a} |
| ay | —lee ale | 12 |
eh T ggoor
| hie. | a | rr | |
| vet | 2h | opie | 28) |
nes 2 5 sve
| Van | ke | Se | |||||
| ‘Men | che | ale 7e | je | R52 | yiDeo | ||
| fe | CAR | ei | a | S$) | out | ||
| a | vibes | Map, | 4p? | ie | |||
| ts | oat | ae | le | 83 | |||
| 2 | Ble | sal? | |||||
| ya | ot | Sin | 4 | iowa | oo | eal 'S | |
| ha | tts | * | eva | pece | —4 | a | [> Reo |
| ve | + | ae | ka | FLASH | yb | 38 | |
| he | + | ors | a | tha | z | cee | BR |
| 2]. | 332 | Pe wnoto: | Sr |
Bon? fe
| loa. | 7 | Des | Z] | vie |
is 9 Is anise
| He | cme | oo |
‘se Ts
| + | Ly | 6 | |
| " | ale | ev | NOTICE TO ALL PERSONS RECEIVING THIS ORAWING |
3} CONFIDENTIAL Reproduction forbidden withoul the 7 Giitorna this crowing ws only conetionally waved. aed
l drawing oF any sesign or technea information shown
en license. no right lo reproduce this drawing is granted or the subject mater thereo!_unless By written agreement tah oF writen permission tram the earparation
Figure 17 Printed Circuit Board Schematic Diagram
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
o ce 6 1 PDs
Poa
PDS
Poe
POT ving vib
vida
Pepa
ww svacn- -— ee Sle Vad
wsver [a] he Sve 1,
cre esvac
asvac [x Alar
esver [¥ Rif
JE “ TRASH
3 aro 2 thin é A?
~ HEV (UnRee +Leaa av RI 2,4, 5.212509 NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL. Reproduction forbidden without Ine specific writien permission of Atari, Inc. Sunnyvale. Calilorma. This drawing 1s only conditionally issued. and neither receipt nor passession thereat conters or ransters fany right in. ar lcense lo Use, the subject matter of Ihe ‘aeaming of any design or technical information shown thereon. ar any right to reproduce ines drawing or any part theteot. except fer manulacture ay vendors of Alan Inco porated and for manulacture under the corporalicn’s wet fen licange.no right to reproduce this drawing 's granted or the subject matter theres! unless by writien agreement with-oF written permission Irom the corporation
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
NOTIGE TO ALL PERSONS RECEIVING THIS ORAWING CONFIDENTIAL, Reproduction forbidden without tne specific written permission of Atarr. Inc. Sunnyvale, Calilorna, This drawing 1s only conaitionally :ssued. and neither receipt nor possession thereot confers or transfers. any right in. or license to use. the subject matter of the ‘Srawing ar any design oF technical snformalion shown tmereon, narany right to tenraduce this drawing or any part Inereot. except for manulacture by vendors of Ata InCor porated and fot manulacture under the corporation's wrt fen license. no right to reproduce ths drawings granted or the subject matter thereo! unless oy writlen agreement z ‘uth or wnten permsson trom ine corporation an TP. ex fF.
| = | ov | | ten |
| 1 | OUT | | °3[Ww |
Te TP 8 ex Ke
| Nov | on | ni | —— 7 |
OUT | ,3]w ENCLOSURE! v 1H OT Ve WEN Sa 2 5% Oy xr 25% 99 MONITOR, LW
x Nev?
NO) BK/OR be TEERIN “sine | |>| MEESINC
FLUORESCENT UGuT
ae eee 5 COIN 1 COUNTER! Lockour! J cow | SLAM 4 Mii Shi Zz] 1 aly
' —u
Figure 18 Harness Schematic
POWER SUPPLY
Figure19 TEC TV Monitor Schematic
pylons, cars, and CRUNCH graphics), and objects 8 through 15 (arrows) do not interfere with game progress at all.
Playfield RAM addresses come through multiplexers E7 and F7, allowing the microprocessor to load during V Blanking.
Super Bug Car Picture The CAR VIDEO output (sheet 3) comes, one bit at a time, from the output of multiplexer K7. This output results in a TV monitor display of the Super Bug car turned in one of 24 possible directions of rotation. However, car picture ROM K6 contains only four rotational pictures of the Super Bug car.
By exchanging the horizontal and vertical sync address inputs (J6, K5, L6) to car picture ROM K6, the four rotational pictures from the ROM are increased to eight pictures. By inverting the horizontal and vertical sync inputs (J5, K5, L5) to multiplexers J6, K5, and L6, the eight rotational pictures from ROM K6 are increased to 24 pictures.
Select inputs RO and R1 of multiplexer K7 determine the data bit output of car picture ROM K6.
Flip-flops M7 and associated gates produce the timing necessary to enable the car picture to be displayed in the center of the TV monitor. Audio The microprocessor puts sound data on the data bus. IC B5 latches data for the frequency of the motor sound. IC D8 latches data for the frequency of the crash sound.
Latch C9 uses address bits BAO through BA3 to select, on command, the start lamp, the track select and the FLASH signal which inverts the video. C9 also permits the microprocessor to select the ATTRACT signal, which turns the sound on and off.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Seller warrants that its printed circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) Soe ren ace of stinment Seller warrants that its television monitors (in games.
supplied with monitors) are free from defects in material and ee
‘normal use and service for a period of thirty (30) days from date of shipment. the Seller's other products or parts thereof are warranted, If the products described in this manual fail to conform to this warranty, Sellers’ sole liability shall be, at its option, to repair, replace, or credit Buyer's account for such products which are returned to. during said warranty period, provided:
- Seller is promptly notified in writing upon discovery by Buyer that said products are defective;
{c) Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation or improper testing.
EXCEPT FOR ANY EXPRESS WARRANTY SET FORTH IN A WRITTEN CONTRACT BE-
TWEEN SELLER AND BUYER WHICH CONTRACT SUPERSEDES THE TERMS OF THIS
ORDER, THIS WARRANTY IS EXPRESSED IN LIEU OF ALL OTHER WARRANTIES EX- PRESSED OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTA- BILITY AND FITNESS FOR A PARTICULAR PURPOSE, AND OF ALL OTHER OBLIGA-
TIONS OR LIABILITIES ON THE SELLER'S PART, AND IT NEITHER ASSUMES NOR
AUTHORIZES ANY OTHER PERSON TO ASSUME FOR THE SELLER ANY OTHER LIABILITIES IN CONNECTION WITH THE SALE OF PRODUCTS UNDER THIS OR-
This document is and contains confidential trade secret information of Atari, Inc. This document is loaned under confidential custody for the sole purpose of of tion, maintenance or repair of Atari equipment and may not be used by or disc to any person for any other purpose whatever, and remains the property of Atari,
Neither it nor the information it contains may be reproduced, used, or disclosed to -aneed to know consistent with the purpose of the loan, without written consent of Atari, Inc.