Kozmik Krooz'R Parts and Operating Manual (Mar 1983)
Kozmik Kroozr (Bally Midway, 1982) · Parts & Operating Manual · 100 pages · 67 sections · original scan
Form No. 0639-00300-0000 Phone: (312) 451-1360 March 1983
MIDWAY MFG. CO.
10750 W. Grand Avenue Franklin Park, Illinois 60131 U.S.A.
Cable Address: MIDCO Telex No.: 72-1596
ELECTRICAL BULLETIN: FOR ALL APPARATUS COVERED BY THE CANADIAN STANDARDS ASSOCIATION (CSA) STANDARD C22.2 NO. 1, WHICH EMPLOYS A SUPPLY CORD TERMINATED WITH A POLARIZED 2-PRONG ATTACHMENT PLUG.
UNEESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE
ATTENTION: POUR PREVENIR CHOCS ELECTRIQUES NE PAS UTILISER CETTE FICHE POLARISEE AVEC UN PROLONGATEUR. UNE PRISE DE COURANT OU UNE AUTRE SORTIE DE COURANT, SAUF SI LES LAMES PEUVENT ETRE INSEREES A FOND SANS EN LAISSER AUCUNE PARTIE A DECOUVERT.
Cillly|MIDWAY
Inuiles You To Use
OUR TOLL FREE NUMBERS FOR SERVICE INFORMATION CONCERNING THIS GAME, OR ANY OTHER BALLY/MIDWAY™ GAME YOU NOW HAVE ON LOCATION.
CALL US FOR PROMPT, COURTEOUS ANSWERS TO YOUR PROBLEMS
ANSWERS TO YOUR PROBLEMS.
Continental U.S. 800-323-7182 Illinois Only 1-800-942-0497
© COPYRIGHT MCMLXXXI!l BY BALLY/MIDWAY CO. ALL RIGHTS RESERVED. NO PART OF THIS PUBLICATION MAY BE REPRODUCED BY ANY MECHANICAL, PHOTOGRAPHIC, OR ELECTRONIC PROCESS, OR IN THE FORM OF A PHONOGRAPHIC RECORDING, NOR MAY IT BE TRANSMITTED, OR OTHERWISE COPIED FOR PUBLIC OR PRIVATE USE, WITHOUT PERMISSION FROM THE PUBLISHER. THIS MANUAL iS FOR SERVICE USE ONLY, AND NOT FOR GENERAL DISTRIBUTION. FOR PERMISSION REQUESTS, WRITE: MIDWAY MFG. CO., 10750 W. GRAND AVE., FRANKLIN PARK, IL 60131 Printed in U.S.A.
DESCRIPTION | TABLE OF CONTENTS
Introduction
Location and Setup
Self-Test ... Game Volume Adjustment Control Option Switch Setting
Game Operation Self-Test Mode Attract Mode... Ready-To-Play Mode Play Mode Two Player Opera
Maintenance and Repair Cleaning Fuse Replacement Opening the Control Panel. Removal of Main-Display-Glass and T.V. Bezel T.V. Monitor Replacement.. Printed Circuit Board Replacement. Opening the Attraction Panel... Servicing the Black Light Above Control Console Servicing the Fiuorescent Light Behind the Front Service Panel . Illustrated Parts Breakdown No. 639 - Kosmik Krooz'r- Front... No.639-Kosmik Krooz'r-Front- Parts List oe sone sees No. 639~Kosmik Krooz'r - Header Fluorescent Light Assy. and Black Light Ass No. 639 - Kosmik Krooz’r - Header Fluorescent Light Assy. & Black Light Ass; No. 639-Kosmik Krooz’r - Rear Access......... No. 639 - Kosmik Krooz’r - Rear Access - Parts Lis' No. 639- Kosmik Krooz'r-Ship Assy. ... No. 639 - Kosmik Krooz’r- Ship Assy. - Parts List. No. 639 - Kosmik Krooz'r - Analog Control Assy. No. 639 - Kosmik Krooz'r - Analog Control Assy. - Parts List . No. 639 - Kosmik Krooz’r- Knob & Shaft - Encoder Disc Ass} No. 639- Kosmik Krooz’r - Knob & Shaft - Encoder Disc Ass‘ Kosmik Krooz'r- Power Chassis Assy. - 70VA, 115V... Kosmik Krooz’r- Power Chassis Assy. - 70VA, 115V. Parts Lis' Front Door Assy. - U.S.A. 25¢ Front Door Assy. - U.S.A. 25¢- Parts List .......ccccesceseseseessesscseeeensescsnsseseseessaseeseseeseseaneassaesseees
Technical Troubleshooting ............c ce ceecee esc essecseeseeceneseeseeseceeeseacauecasenseeeteasseeeaseceeenetieanaee 5-1 Introduction .... General Suggestions Harness Component Troubleshooting Transformer and Line Voitage Problems... AGlossary of Microprocessor Terms Introduction to the Z80 CPU... General Purpose Registers. Arithmeticand Logic Unit (ALU) instruction Register and CPU Control . Z80 CPU Pin Description................ MCR 11 System P.C. Board Jumper Option:
ili
TABLE OF CONTENTS
DESCRIPTION PAGE
vi.
Vil.
vill. T.V. Monitor Manual Introduction .... Symptom Diagnosis. Guide to Schematic Symbois Troubleshooting. Theory of Operatiot Differences Between Monitors Controls You May Not Touch Parts Interchangeability ... Picture Tube Interchangeability Wells Gardner Monitor Schematic - Wells Gardner Monitor Replacement Parts List . Electrohome Monitor Schematic - 19”...... Electrohome Monitor Replacement Parts List. Electrohome Monitor Schematic - 13”. Electrohome Monitor Replacement Parts List Zenith Monitor - Sweep Board Schematic... Zenith Monitor - Sweep Board Replacement Parts List Zenith Monitor Main Board Schematic .. Zenith Monitor Main Board Replacement Parts List . Zenith Monitor - CRT Socket Board Replacement Parts Lis' Zenith Monitor - CRT Socket Board Schematic . Zenith Monitor Width Step Assy. Schematic ... Zenith Monitor Interconnect for Video Game Schemat
Coin Door Maintenance. .................scccsesssscsiessecssesseesseasiceneaseeneaseesuiecsseessecsnsssacsneeseeaeeseceeseeseessy Metal Coin Acceptor Mechanisms. Plastic Coin Acceptor Mechanisms
Schematics and Wiring Diagrams Wiring Diagram - Upright . 125VA Power Supply P.C.B. - Component Layout.. 125VA Power Supply P.C.B. - Schematic ..... Dual Power Amp P.C.B. - Component Layout. Dual Power Amp P.C.B. - Schematic ........ Optical Encoder P.C.B.- Component Layout . Optical Encoder P.C.B. - Schematic... Super CPU P.C.B.- Component Layout Super CPUP.C.B. - Schematic........... Video Generator P.C.B. - Component Layout... Video Generator P.C.B. - Schemati Super Sound I/O P.C.B.- Component Layout. Super Sound I/O P.C.B. - Schematic......... Analog Joystick P.C.B. - Component Layou Analog Joystick P.C.B.- Schematic ......... Solid State Relay P.C.B. - Component Layout Solid State Relay P.C.B. - Schematic. Sensor P.C.B. - Component Layout Sensor P.C.B- Schematic .... 125VA Power Chassis - Schematic
FIGURE
1-1 1-2 1-3 1-4 1-5 1-6 2-41 2-la 2-1b 2-1¢ 2-1d 2-1e 2-1f 2-1g 2-2 3-1 3-2 3-3 3-4 3-5 3-6 3-7 3-8 7-1 7-2 7-3 7-4 7-5 TABLE OF FIGURES
Installing the Footstool a Location of Serial No., Interlock Switch, On/Off Switc! Interlock Switch Operation ..... Game Volume Adjustment Controi Option Switch Location. Option Switch Setting:
Self Test Mode - Menu
Seif Test Mode - Sounds Self Test Mode - Player Input. Self Test Mode - Bookkeeping
Self Test Mode- Time Report
Self Test Mode - Score Report. Self Test Mode - Setup Options Self Test Mode- Channel Test. Location of Hardware Master Reset Switc! Location of Fuses. Opening the Control Panel Removal of Main Display Glass & T.V. Bezel Removing Monitor - Upright. Replacing P.C.B.'s.. Opening the Attraction Panel
Replacing Fiuorescent Tube Starte:
Servicing Center Auxiliary Lighting
Removing and Replacing the Coin Acceptor Cleaning the Metai Coin Accepto Lubricating the Metal Coin Acceptor. Opening the Plastic Coin Acceptor.. Changing the Plastic Coin Acceptor to Accept American or Canadian Quarters .. RAO hovbnwid SHANDY O
Kozmik Krooz’r
IMPORTANT NOTE
DO NOT plug in your new game yet. Before you do anything to your game, we recommend that you read SECTIONS | and II of this manual completely. It will not take more than a few minutes and it may be very helpful.
Introduction
Your NEW GAME is for one or two players. There is ONLY one model: the “UPRIGHT”. When the two player mode is selected on the Upright model, the players take turns at the controls to guide their player through the game course. When playing this game, you are the controlling force. It is up to you to direct your player successfully through the game course. Your job is to give guidance and provide offensive and defensive strategy to enable your player to overcome all obstacles. Your opponents will use every trick in the book, and may even invent a few new ones, to overcome your various strategies and eliminate your player(s). You really have to keep a close eye on them at all times. As your skill level increases, you will notice that your opponent's offensive abilities greatly increase. Any advantages you once had at the beginning of the game will gradually be reduced until they are completely gone. Bonus players may or may not be awarded depending on the options the game owner has selected. The point values of all items are listed below.
Major Features
Your game has been provided with a new improved Power Chassis designed to help reduce electrical interference with other equipment. It is also equipped with a detailed self-diagnostic package. This includes the following abilities: 1) The game has OWNER/OPERATOR selected variable levels of difficulty so game play can be tailored to player skill level in his area; 2) Thereis a new andeasy to use diagnostic package featuring: a complete ROM/RAM check with bad chip location information read out on the monitor screen; the capability to check each of the game's different sounds INDIVID- UALLY; provision for checking each control and switch SEPARATELY; a full function Bookkeeping mode; an entire options list that can be set from the front console with NO NEED to crawl inside the back of the cabinet and look for tiny switches located on P.C. boards; a sound system test; and a “PRE-SET” category that can return ALL information in tHe Bookkeeping mode tozero and/or all operator selected options back to factory recommended settings; and 3) The game is equipped with a rechargeable battery so that it won't forget where it was the night before at closing — even if you turn it off. It will “remember” this information for up to two weeks.
Game Objective
The object of the game is toHAVE FUN and survive as long as possible while constantly improving your skills and advancing to the highest rack that you can. As you do this, each following rack of the game will have more and greater obstacles for you to overcome, and will in general be harder to complete.
DESCRIPTION
RAM SHIP
SHOOTER SHIP.
STRIKE SHIP
SCOUT SHIP
SPEED DEMON
SPACE MINE
FORMATION FIGHTER
MINE LAYER
SPY SHIP. POINTS AWARDED
2500
Assigned Point Values
1-2 APPEARS IN ALL RACKS
I. Location and Setup
INSPECTION:
1.
2. Remove the game from its shipping crate.
Inspect the entire outside of it for any signs of damage. O Any scratches?, dents?, cracks? O Any broken controls? O Any broken glass or piastic? O Just look it over closely and make a note of any signs of damage.
Remove the shipping Cleats from the bottom ofthe cabinet. 1 UPRIGHT MODELS ONLY: In order to help prevent easy theft of your game, you may wish to remove the Caster Whee! Assemblies from the bottom of your cabinet at this time.
. Install the four fevelers, one at each corner of the cabinet. O Level the cabinet.
. After you have installed the game's Leg Levelers, if desired, you may now install the game's FOOT- STOOL. See Figure 1-1. This is accomplished by: | MAKING SURE NO POWER IS GOING TO THE GAME. O Removing the FOOTSTOOL mounting hard~ ware from its bag. O Install the FOOTSTOOL'S Leg Levelers and set them to approximately the same height as those you just installed to each of the game cabinet’s corners. O Open the coin box door. Q Install the FOOTSTOOL mounting bolts and washers as shown below.
Figure 1-1 Installing the Footstool
- Open the cabinet and inspect the inside of the game for any signs of damage. See Figure 1-2. O Also check to make sure ail plug-in connectors on the wire harness are firmly seated.
CONTROL PANEL
INTERLOCK
FOOTSTOOL
UPRIGHT FRONT SERIAL NUMBER
TV MONITOR
POWER SUPPLY P.C.B
Logic BOARDS
POWER CHASSIS ASSEMBLY
UPRIGHT REAR
Figure 1-2 Location of Serial No., Interlock Switch, & Major Sub-Assemblies
1-4
INSTALLATION
- Location requirements: O Power: Domestic 110 V @ 60 Hz Foreign 200 V to 240 V @ 50 Hz O Temperature: 32° to 100°F (0° to 38°C) O Humidity: Not over 95% relative O Space required: Upright 25"x40" (63x102cm) OD Game height: Upright 72” (183¢m)
. Voitage Selection: Your game is designed to work properly on the line voltage where you are located. Check your line voitage with a meter to determine what its value is. Then check the power input wires to the main power supply transformer on your game to be sure they are connected to taps which correspond to your line voltage value. If the power input wires to the main power supply transformer are not connected to taps which correspond to your local line voltage, move them to the proper taps. \f the line voltage in your area falls outside the upper or lower limits of the range of inputs covered by the main power supply transformer, DO NOT PLUG YOUR GAME‘IN until you have talked with your distributor and/or service man and obtained a solution to this problem. Otherwise you could damage your game. . Interlock and power ON/OFF switches. See Figure 1-2. O To help prevent the possibility of getting an electric shock while working inside the game cabinet, interlock switches have been installed at each cabinet access door (this DOES NOT include the coin door in the Upright models). O When any access door is opened, the interlock switch installed there turns off all power to the game. © Check each operation. After checking the line voltage in your area and determining that the input wires to the main power supply transformer of your game are cannected properly — or — after obtaining a solution to your over or under voltage problem from your distributor and/or your service man, plug the game into your A.C. wall outlet. The game ON/OFF switches for all models are located as shown in Figure 1-2. Turn the game on and allow it to warm up a few minutes. Slowly open each access door to the game (this does not include the coin door on the Upright models). interlock switch for proper As the door is opened approximately 1” (2.54cm) the power to the game should go off (the T.V. monitor, all the lights, and all sounds will stop). \f this does not happen, check the interlock switch by this door to see if it has broken loose from its mounting or if it is stuck in the “ON” position. If the switch is found to be bad, turn the game off, unplug it, and replace the interlock switch. When done, plug the game back into the wall outlet, close the access door, and turn the game back on. After the game has warmed up, repeat the above interlock switch test. When the interlock switch is working properly and turns the power to the game off, power may be restored to the game with the access door(s) open. Take hold of the interlock switch plunger and gently pull it out to its fully extended position. THIS IS TO BE USED ONLY FOR SERVICING THE GAME. See Figure 1-3.
Figure 1-3 Interlock Switch Operation
SELF-TEST Your new game wiil Self-Test itself to see if it has any bad parts. The information it receives while testing itself will be shown on the T.V. monitor. Some information can also be heard through the game's speaker system. See the SELF-TEST section for a more detailed description of this function. When there is a bad resutt according to the Self-Test, call your distributor and/or service man to have the trouble fixed unless it is something you can do yourself (such as replace a bad RAM or ROM chip).
GAME VOLUME ADJUSTMENT CONTROL See Figure 1-4. The game volume control pot is just inside the cabinet, not far from the coin door frame. There is only one pot. For adjustment, it may be reached through the coin door. To make the squnds louder, turn the pot clockwise as you face it ( ). To make the sounds less loud, turn the pot counterclockwise as you face it (f~ ).
OPTION SWITCH SETTINGS To change the most common option switch settings, you DO NOT have to take the game apart or go into the cabinet and hunt for tiny switches on P.C. boards. These most common options can be changed from the main console of the game while it is in the Self- Test mode. The Self-Test switch is located just inside the cabinet not far from the coin door frame as you face it. When changing any options, ALWAYS perform the Self-Test and play the game to be sure the ones selected are working properly. Of course, when you must change one of the switches that is located on one of the game's P.C. boards, it is also recommended that you perform the Self-Test and play the game to be sure the switches have worked properly and that no switches were accidentally moved that were not meant to be. (These switches are small and this can happen.) SERVICE CREDIT SWITCH
SELF-TEST SWITCH
VOLUME ADJUSTMENT
Figure 1-4 Game Volume Adjustment Control
The P.C. Board option switch settings, and what they will make the game do are shown in Figure 1-6. These switches are MAINLY INTENDED for use by a technician who is checking and/or performing tests on the game. See Figure 1-5 for option switch locations.
OPTION SWITCH 1
Figure 1-5 Option Switch Locations
KOZMIK KROOZ’R
OPTION SWITCH SETTINGS
SW#1 SW#2 SW#3 SW#4 SW#5 SWHE SWH7 SW#8 SWH9 SW#10) NOT NOT NOT NOT NOT NOT NOT NOT USED USED USED USED USED USED USED USED
COCKTAIL TABLE UPRIGHT
FREEZE VIDEO **NORMAL OPERATION
SWITCH NO. 3 — AT D14 — LOCATED ON SOUND I/O P.C. BOARD
SWiH1 SW#2 SW#3 SWH4 **NORMAL OPERATION OFF SOUND 1/O DIAGNOSTIC MODE] ON
**NORMAL OPERATION RAM/ROM TEST ON INDICATES TEST RESULTS VIA YELLOW LED ON SOUND I/O BOARD: FAST FLASH = BAD ROM
SLOW FLASH = BAD RAM
**NORMAL OPERATION OSCILLATOR TEST ON
** NORMAL OPERATION OFF FILTER TEST
NO EFFECT IF SW#1 OF SWITCH NO. 3 IS IN THE “OFF” POSITION. ** INDICATES FACTORY RECOMMENDED SETTINGS. DURING GAME PLAY:
* PART NO. IM051-00639-A014
THE REMAINDER OF YOUR NEW GAME'S MOST COMMON OPTION SETTINGS ARE CONDUCTED DURING THE MACHINE SETUP PORTION OF THE SELF-TEST MODE AND WILL BE COVERED IN DETAIL IN THAT SECTION OF YOUR MANUAL.
Figure 1-6 Option Switch Settings
II. Game Operation
SELF TEST MODE
The Self-Test mode is a special mode for checking game play statistics as well as game switches and computer functions. It is the easiest and best way to check for proper operation of the entire game.
- If the game is in the Attract mode when the Self- Test switch is moved to the “ON” position, it will finish the sequence and then go into the Self-Test mode. This is illustrated by the display of the Self- Test Mode Menue on the monitor screen. If the game is in the Ready-To-Piay mode or the Play mode when the Self-Test switch is slid to the “ON” position, it WILL NOT go into the Self-Test mode until AFTER the game is over. At this point, the game will go into the Self-Test mode. Again, this is illustrated by the display of the Self-Test Mode Menue on the monitor screen. The fastest way to enter the Self-Test mode is to slide the Self-Test switch to the “ON” position and then activate the “TILT” switch located on the back side of the coin door just below the lock mechanism. The game will then IMMEDIATELY go into the Self-Test mode.
The Self-Test mode has eight (8) major categories as illustrated by Figure 2-1.
- Itis easy to select what category you want to enter. By following the ON SCREEN instructions, the Cursor at the left of the screen can be moved UP or DOWN until it is in front of the category you want to test. . After the Cursor has been positioned, follow the ON SCREEN instructions again, and the monitor screen will display the test category you have selected.
- including ALL information in the “BOOKKEEP- ING” mode, and ALL operator selected options, will be set back to zero (“0”) and to the factory recommended settings — respectively.
2-1
SELECT DESIRED TEST
1 SELF DIAGNOST 2 SOUNDS 3 PLAYER INPUT 4 BOOKKEEPING 5 MACHINE SETUP 6 CHANNEL TEST T PRESET 8 GRID DISPLAY
POSITION CURSOR BY...
Figure 2-1 Self-Test — Menue
0 Once you are IN one of the Self-Test mode categories, FOLLOW THE ON-SCREEN IN- STRUCTIONS TO COMPLETE THE TEST.
- The next group of Figures show the CORRECT screen presentation for EACH category of the Self-Test mode. During the SELF DIAGNOSTICS section of the Self-Test mode, you will first see a cross hatch pattern on the screen for about 1/2 second. Second, you will see a lot of different colored bars shown on the monitor screen. These bars will be UNpainted one at a time from the top down. Third, you will see the screen painted Red, Blue, and Green in bars from the top down. Fourth, all the different colored bars you saw “Second” are displayed again. And fifth, the different colored bars are replaced by an exit message. If you do not exit, the test will repeat itself. This feature was designed into the game to enable over-night testing for an intermittent hardware problem. If the SELF DIAGNOSTICS find one or more bad ROM or RAM chips: instead of going through what is described above, the game wiil give you a written message as to which parts are bad=This message includes their I.D.’s and their P.C. Board locations.
During the SOUNDS section of the Self-Test mode, the game will give a display which looks like that shown in Figure 2-1a. C In this category, each of the game's separate sounds can be checked individually in any order — or — you can tell the game to check them all in order. During the PLAYER INPUT section of the Self-Test mode, the game will give a display which looks like that shown in Figure 2-1b. O In this category, each of the game's player operated controls — including the coin switches on the back side of the coin door — may be checked individually. A game sound will be heard as each switch/control is actuated. If no game
SELECT A SOUND
1 ALL SOUNDS 2 EXIT :
REMAINDER OF GAME SOUNDS CALLED OUT IN ORDER
POSITION CURSOR BY...
Figure 2-1a Self-Test — Sounds
PLAYER INPUTS
PLI FIRE
and Devices are activated, the ig spelled out in the space As the Player Input 5 Switch or Device indicated.
MINI UPRIGHT
1 COIN METER
ACTIVATE ALL PLAYER INPUT
SWITCHES AND DEVICES _ HIT TILT 10 EXIT
Figure 2-1b Self-Test — Player Inputs sound is heard, that switch/control is either not working, miswired, or disconnected. Check it out thoroughly. During the BOOKKEEPING section of the Self-Test mode, the game will give a display which looks like that shown in Figure 2-1c, O In this category a basic bookkeeping function is performed. And with the selection of the “TIME REPORT” and the “SCORE REPORT”, detailed breakdowns of game times and scores may be obtained. In the TIME REPORT and SCORE REPORT sections of the BOOKKEEPING mode, the game will give displays which look like those shown in Figures 2-1d and 2-1e respectively.
SELECT A REPORT OR EXIT
CHUTE 1 COINS
CHUTE 2 COINS LONGEST GAME | SHORTEST GAME HIGHEST SCORE LOWEST SCORE TIME REPORT SCORE REPORT EXIT
POSITION CURSOR BY...
Figure 2-1c Self-Test — Bookkeeping 05 18 00-43 86310
TIME REPORT 8 1030. SEC 30 10 60 SEC 60 10.90 SEC 90 TO 120 SEC 120 10 150 SEC 150 TO 180 SEC 3704 MIN 4105 MIN 5 TO 6 MIN QVER 6 MIN
Figure 2-1d Self-Test — Time Report
SCORE REPORT 070 5000 PTS © 5000 TO 10000 PTS 10000 TO 20008 PTS 20000 TG 40000 PTS 40000 0 70000 PTS 70000 TO 100000 PTS 100080 Ta 150000 PTS 150000 TO 200000 PTS 200000 TO 250000 PTS OVER 250000 PTS
Figure 2-1e Self-Test — Score Report During the SETUP OPTIONS section of the Self-Test mode, the game will give a display which looks similar to that shown in Figure 2-1f. D In this category, all common game options may be changed from the contro! console: coins per credit, credits per base, bonus base(s) awarded at, difficulty level - -, and so on.
SETUP OPTIONS
COIN CHUTE 1 “1 COINS FOR *) CREDITS
COIN CHUTE 2 *1 COINS FOR “F GREDITS
*) CREDITS FOR “3 BASES IST EXTRA BASE AT *20000 POINTS
ADDITIONAL BASE EVERY *20000 POINTS
*3 DIFFICULTY LEVEL
- = Factory recommended settings. Figure 2-1f Self-Test — Set-Up Options
DIFFICULTY LEVEL EXPLANATION: The Difficulty Levei setting has a range of 1 to 9. With 1 being the easiest level of play and 9 being the most difficult level of play. We recommend that a setting of 3 be used as a beginning point.
2-3 Game play can then be made MORE difficult or LESS difficult, according to the skill levels attained by the players in your area. CHANNEL TEST: During the CHANNEL TEST section of the Self-Test mode, the game will give a display which looks like that shown in Figure 2-1g. O In this category, the game conducts a test of its SOUND SYSTEM. Once you enter the CHANNEL TEST section of the Self-Test mode, the game automatically tests Channels 1 through 6 giving a tone for each one as it checks it. After the 6th Channel is tested, the game automatically repeats the test until exited. It then goes back to the Self-Test Mode Menue. During the GRID DISPLAY section of the Self-Test mode, the game showsa white cross hatch pattern on the monitor screen. This is for alignment and/or test purposes. This pattern will remain on the monitor screen until exited. The game will then go back to the Self-Test Mode Menue. To leave the Self-Test mode, simply slide the Self-Test switch to the “OFF” position at ANY time. The game will then run through the ROM/RAM test display after which normal game functions will return to the monitor screen.
CHANNEL TEST CHANNEL 1 CHANNEL 2 CHANNEL 3 CHANNEL 4 CHANNEL 5 CHANNEL 6
Figure 2-1g Self-Test — Channel Test
RACK ADVANCE: The game can be made to advance through the various racks by beginning a game and THEN sliding the Self-Test switch to the “ON” position. After this has been done, each time you depress the ONE PLAYER BUTTON the game will advance one rack. When you reach the desired rack, slide the Self-Test switch to the “OFF” position. (If you leave the Self- Test switch in the “ON” position, the game wili go into the Self-Test mode when you are finished playing.)
CROSS HATCH PATTERN: A cross hatch pattern is shown on the screen when power is first turned on to the game, when the TILT Switch is actuated, and during the “SELF DIAGNOS- TIC” portion of the Self-Test mode, and during the “GRID DISPLAY” portion of the Self-Test mode. This pattern may be kept on the screen for adjustment purposes as described earlier. When you are finished using the cross hatch pattern, simply exit at the GRID DISPLAY to return to the Self- Test Mode Menue. HARDWARE MASTER RESET SWITCH: There are two of these little red switches, one on the Sound I/O Board and one on the CPU Board, located as shown in Figure 2-2. The function of each of these switches — when pressed — is to make the game think it has JUST been turned on. They set up an “initial power-up” condition. We DO NOT recommend that you indiscriminately press EITHER of these switches. They should ONLY be used if there is a major problem encountered while testing the P.C. Boards.
HARDWARE MASTER RESET SWITCH
Figure 2-2 Location of Hardware Master Reset Switch
ATTRACT MODE
- The Attract mode starts: O Just after power has been turned on to the game. (Self-Test switch is in the “OFF” position.) O After a Seif-Test has been completed and there are no more Credits left in the game's memory, O After a play has been finished, the score was not high enough to put the game into the High
2-4 Score/Initia) mode, and there are no more credits left in the game’s memory. D After the High Score/Initial mode when there are no more credits left in its memory. In the Attract mode, the game will give the following displays centered on the monitor screen:
CHEOITTS o
resent corn
SRE Trade" Tate ee
“SIStT™
Attract Mode Display 1
Attract Mode Display 2
==
Attract Mode Display 3 CRESETS 5 THE KOZETK KRWGZR IS KEYES
BEING THE RIGKT GDYSTIOK use THE TRECEEN FUR FIRING SXISILES RBERTE THe «Ge QR FXKRE OteRECTIae PFU OGEN Ge KNOB FER SHIELS
Attract Mode Display 4
cerepiTs o YOUN EXSSiON XS TH PROTECT THE KOZEXK KRODZR FRoe SLXEN ATTHCKERS TRE KRORZR ts SAFE FRGE ATTACK OHLY ATEN IF WAS ENTERED THE BOTHER SHrP
Attract Mode Display 5
CwRepxrTs < THe KUZEIEK xeooze sR
ENTER CHE AETHER SHXP UML. Sven BH CHNGO Purr HHS SEEN SOTHTES reo THe FroRtEAND eusxTraN
Attract Mode Display 6
O No matter where the game is in the Attract mode sequence, it will immediately go to the following display as soon as a game has been paid for.
CeESETS o
SESTRLY SRERY ABTTACKERS
CREBITS
Attract Mode Display 7
Ready to Play Mode Display 1
CRESZTS &
SOINE VALUES aan sure 2 gy SOUTER sHxP @ STHXKE suxP ap MCT sure sence wxrce A,
Attract Mode Display 8 fae ne +ro., Se fase i srevens
Ready to Play Mode Display 2
cwepxrs & READY-TO-PLAY MODE
- The Ready-To-Play mode starts when enough coins have been accepted for a 1 or 2player game. 2, The Ready-To-Play mode ends when either the “{ PLAYER” or the “2 PLAYER” push button is pressed.
- In the Ready-To-Play mode, the game will give the above dispiays centered cn the monitor screen,
- If no START button is pressed, the displays will Attract Mode Display 9 remain indefinitely as shown above.
2-6
PLAY MODE
- The Play mode begins when either the “1 PLAY- ER” or “2 PLAYER” start button is pressed.
- The Play mode ends when all of your SHIPS have been eliminated. When this happens, “GAME OVER” is written across the center of the monitor screen.
- ON THE SCREEN: The game is made up of 20 racks which increase in difficulty as you go along. After the 20th rack has been completed, the game repeats the basic format for rack #1 but adds some additional obstacles that were not there the first time you played it. At the beginning of each rack, the game tells which player is up. Also indicated in each rack is that rack’s number, «the number of players (1 or 2), a running total of the player's score(s), time left on shield, and the highest game score to date. PLAY BEGINS: Your SHIP appears at the bottom of the screen, after all other objects have appeared. Play then begins for your SHIP. Your SHIP is protected for the first few seconds after it has appeared. This is indicated by its flickering image
- protection ends when the image solidifies. ENEMY SHIPS/MINES/SPEED DEMONS, ETC.: Initially, you will experience only one type of attacker at any one time per rack. In later racks, you will have several different types of attackers per rack coming at you at any one time. The characteristics of each attacker are different. All the Enemy SHIPS/MINES/SPEED DEMONS, ETC. listed in the scoring table will eventually appear during the game course. Certain ones only appear in the higher, more difficult, racks; and/or, if you spend too much time in any one rack. As your abilities improve, you'll find out which these are. al
a
PLAYER 1 SCORE
- BLACK HOLE: The BLACK HOLE is one of those little surprises | was telling you about above. It appears if you should spend too much time in any one rack — or — when your skills have improved enough to reach the upper racks. When it latches on to your SHIP, it will take it all over the screen for about 15 seconds. During this time you still are able to fire your SHIP'S weapon and to use your shield, but you have NO control over your direction on the screen.
- SMART BOMBS: These appear randomly as atom-like shapes and move randomly over the screen, While doing this they alternate colors between green and blue. If shot when they are green, they will explode and wipe out everything on the screen EXCEPT your SHIP. If shot when they are blue, nothing happens. Also, touching them with your SHIP at any time will cause NO problems.
- MISSILE FIRE: This is done by pulling the trigger of your joy stick. Pull and release — one missile is fired. Pull and hold — four missiles are fired — short pause — four more missiles are fired, and so on.
- MISSILE AIMING: Rotating the knob on the left side of the control panel will aim your SHIP’S launcher in any of 8 directions.
- SHIELD: Your SHIP'S shield is activated by pushing down on the MISSILE AIMING knob. The shield does not last very long so be careful how you use it. It can only be recharged by guiding your SHIP inside the mother ship through one of its rotating ports. Your shield time is displayed at the bottom center of the screen.
- SHIP: Your SHIP can move LEFT, RIGHT, UP, and DOWN on the screen. Its movements are controlled by the joy stick on the game's control panel.
KOSMIK KROOZ'R
‘SMART BOMB
RAM SHIP
Display of “On-Screen” Graphics During Game Play
12.
13.
14.
15. KOZMIK JUNK YARD: This is a BONUS RACK. It appears every fifth rack (5th, 10th, 15th, 20th, etc.). You CANNOT loose a SHIP here. There are four parts scattered throughout the junk yard for you to pick up before the time limit runs out. If you get all four, you can get an extra SHIP awarded to you. There are hazards in the junk yard that can siow you down. The chief one of these is the trails of space turbuience caused by passing asteroids. You cannot maneuver across them. There is also a talking inhabitant of the junk yard that will detect your presence and bend yourear if you get too close to his residence. And once this happens, you won't be able to get away until he's done talking. BONUS SHIPS: These can be awarded to the player as he reaches or passes certain preselected point values. This feature is adjustable by the game’s Owner/Operator. PLAY ENDS: When your last SHIP is eliminated, “GAME OVER’ is written across the center of the monitor screen, HIGH SCORE/INITIAL MODE: If your score was high enough to become one of the ten best scores, the game will go into the High Score/ Initial mode immediately after the above display. {f your score is not high enough to cause the game to go into the High Score/initial mode, it will either go to the Attract mode (if there are no more credits left in its memory) or into the Ready- To-Play mode (if there are still credits left in its memory). In the High Score/Initial mode the game gives a dispiay which looks like that shown below.
High Score/Initial Mode 16. Follow the ON-SCREEN instructions to enter your initials next to your score in the league of the best ten players to date. When you've printed Gut your last initial, move the cursor opposite the “END” word and activate the same control you did to enter your initials. This tells the game you are through printing out your initials. The game will then give the following RANKINGS display showing your score opposite your ranking and your initials. See below.
CuREOITS «
Rankings Display
TWO PLAYER OPERATION The Upright models all have two player operation. In the two player mode, the rules of play are thesame as in the single player mode. There are some additional rules, however. 1.
2. The players must take turns at the controls. Your turn lasts until: A. Your SHIPS are ALL eliminated. B. Your SHIPS have ALL entered the mother ship.
SHIP ELIMINATED — OTHERS REMAINING IN RESERVE O The game stops and your next SHIP is displayed on the screen. O Game piay then resumes for you. YOUR LAST SHIP ENTERS THE MOTHER SHIP O Your SHIPS are returned to you and bonus points for each returned SHIP are displayed on screen. © Next, the game indicates the other PLAYER is up, that player's pattern and SHIP appear on the monitor screen, and game play begins for that PLAYER. O This PLAYER'S turn will last until either ALL his SHIPS are eliminated or until they all enter the mother ship. SHIP ELIMINATED — NO OTHERS REMAINING IN RESERVE O Game displays: “PLAYER __” “GAME OVER" on the monitor screen.
O Next, if your score was high enough, the game will go into the HIGH SCORE/INITIAL mode. After this, it will indicate that the remaining PLAYER is up, that player's pattern and SHIP appear on the monitor screen, and game play begins for him. O If your score was not high enough to cause the game to go into the HIGH/SCORE INITIAL mode, it will indicate that the remaining PLAY- ER is up, that players pattern and SHIP appear on the monitor screen, and game play begins for him.
LAST PLAYER'S SHIP ELIMINATED — NO OTHERS REMAINING IN RESERVE O Game displays: “PLAYER ___” “GAME OVER” on the monitor screen. O Next, if your score was high enough, the game will to into the HIGH SCORE/INITIAL mode and then either to the Attract mode (if there are no more Credits left in its memory) or into the Ready-To-Play mode (if there are still credits left in its memory). C If your score was not high enough to cause the game to go into the HIGH SCORE/INITIAL mode, the game will either go to the Attract mode (if there are no more credits left in its memory) or into the Ready-To-Play mode (if there are still credits left in its memory).
2-9
Ill. Maintenance and Repair
Your NEW game needs certain types of maintenance to keep it in good working order. CLEAN, well MAINTAINED games attract players and EARN MORE PROFITS. The most important thing for you to remember is to run the Self-Test EVERY TIME you collect money from the coin box. JUST LOOKING at your game WILL NOT tell you if all its controls and inside parts are working correctly. The Self-Test will inform you whether or not your game is working the way it should. The second most important thing you should remember is to clean the outside of the game and coin acceptor mechanisms on a regular basis.
CLEANING The outside of the game cabinet plus the metal can be cleaned with any non-abrasive household cleaner. However, the front of the T.V. monitor tube and beth sides of all other glass and plastic on or in the game MUST be cleaned with anti-static cleaner ONLY. For cleaning the coin acceptors: hot soapy water may be used on the plastic ones and any household cleanser may be used on the metal ones. If you wish, special coin machine cleaners that leave no residue may be purchased from your distributor. DO NOT dry-wipe any of the plastic panels. This is because any dust that was on them can scratch their surfaces. If this has happened, anyone looking through this type of damaged plastic would fee! he was looking at the game through a fog. This fogging damage CANNOT be repaired or reversed. The ONLY solution is to replace the damaged piece of plastic.
FUSE REPLACEMENT This game contains several fuses located as shown in Figure 3-1.
- UPRIGHT MODEL: As viewed from the back, facing the cabinet, with the rear access door(s) removed; the fuses are located on the Power Chassis and the Power Supply P.C. Board. Replace fuses ONLY with the type and size listed in the Illustrated Parts Breakdown Section of your manual. See the T.V. Monitor Manual (available on request from your distributor or the monitor manufacturer) and/or the T.V. Troubleshooting Section of this manual for information on these fuses.
FUSES LOCATED ON POWER SUPPLY BOARD. AND POWER CHASSIS
Figure 3-1 Location of Fuses
OPENING THE CONTROL PANEL
- UPRIGHT MODEL: See Figure 3-2. O The control pane! is held in place by a nyion retaining Strap and three latches, one on each side and one in the center at its back edge. They are spring loaded to provide constant positive pressure on their latch plates. They can be reached through the coin door AFTER turning power to the game off. To release the latches, lift up and toward the front center of the control panel. Once they are released, unhook them from their latch plates. To remove the control panel: Raise it up and tilt it toward you until you can see the cable and nylon retaining strap behind it. Cradling the control panel between yourself and the cabinet, disconnect it from its cabling and nylon retaining strap.
UPRIGHT
Figure 3-2 Opening the Control Panel The control panel is now free and can be removed, O To reinstall the control panel, procedure. reverse this
REMOVAL OF THE MAIN-DISPLAY- GLASS AND/OR THE TV. BEZEL ASSEMBLY
- UPRIGHT MODEL: O Turn the power to the game off and remove the screws which secure the glass clamping plate in position. See Figure 3-3. C Lift out the glass clamping plate. This frees the main-display-glass so it can be lifted up. O By putting your finger in the hole in the middle of the main-display-glass support, you can lift it up and out. O To reinstall the main-display-glass and glass clamping plate, reverse this procedure.
DISPLAY GLASS
GLASS CLAMPING PLATE
Figure 3-3 Removing the Main-Display-Glass & T.V. Bezel
T.V. MONITOR REPLACEMENT
- UPRIGHT MODEL: See Figure 3-4. O Turn power off to the game. O Open the rear access doors. O Completely disconnect the T.V. monitor from all its cabling. DON’T FORGET THE CHASSIS GROUND WIRE. O With the removal of only four bolts, the T.V. monitor will be loose.
REMOVE (4) BOLTS
Figure 3-4 Removing the Monitor The monitor mounting bars slide on top of and against two metal guides mounted to the cabinet’s right and left sides. The monitor is removed by sliding it out the back of the cabinet. See Figure 3-4. O To reinstall procedure. 0 After replacing the T.V. monitor, be sure to run the game Self-Test. PRINTED CIRCUIT BOARD (P.C.B.) REPLACEMENT
- UPRIGHT MODEL: See Figure 3-4. O Turn the power to the game off. Unlock and open the rear access door(s). C Disconnect al! cabling from the P.C. boards and lift them out of their card rack. O Disconnect the linear power supply board from all its cabling, remove the P.C.B. support(s) indicated in Figure 3-5, and slide the linear power supply board out the back of the cabinet. O To reinstall the above P.C.B.'s, procedure. the T.V. monitor, reverse this
reverse this
REMOVE SUPPORT FROM SIDE OF CABINET AND LIFT P.C.B'S UP TO REMOVE REMOVE SUPPORT AND LIFT POWER SUPPLY BOARD UP TO REMOVE
Figure 3-5 Removing the P.C.B.'s
OPENING THE ATTRACTION PANEL
- UPRIGHT MODEL: UD Turn the power to the game off.
O Opening the attraction panel: Remove the screws which secure the top bracket in place. (They are on its top side.) See Figure 3-6. Remove the top bracket and slide up the attraction panel. This exposes the speakers, fluorescent tube, and their mountings. To reinstall the attraction panel, reverse this procedure. O The fluorescent light tube may be replaced at this time. BE CAREFUL NOT TO DROP IT.
O Replacing the fluorescent light tube starter. See Figure 3-7. Be sure the power to the game has been turned off. Grasp the starter (it is on the back of the mounting bracket), give it a quarter turn, and remove it from its socket. To replace the fluorescent light tube starter, reverse this procedure. O Removing the speaker(s): The attraction panel MUST be removed first. This. will enable you to reach all the necessary areas where cables MUST be disconnected. Disconnect the speaker(s) from all their cabling. Remove the screws which secure the speaker grill to the cabinet.
1/4 TURN TO REPLACE REMOVE SCREWS AND LIFT ATTRACTION PANEL UP.
Figure 3-6 Opening the Attraction Panel
The speaker attachment nuts and bolts may now be removed and the speaker(s) taken out of the cabinet through the hole in the front of the game where the attraction panel was mounted. To reinstall the speaker(s) and speaker grill, reverse this procedure. Replacement of the fluorescent tube mounting bracket assembly. Disconnect it from its power cable. Remove the screws which secure it to the cabinet. To reinstall the fluorescent tube mounting bracket, reverse this procedure.
FLUORESCENT TUBE STARTER
Figure 3-7 Replacing Flourescent Tube Starter
3-4
SERVICING THE BLACK LIGHT ABOVE CONTROL CONSOLE
- UPRIGHT MODEL: 1 Turn the power to the game off and remove the screws which secure the glass clamping piate in position. See Figure 3-8 Lift out the glass clamping piate. Remove the screws which secure the bottom of the black light shield to the front service panel. BE SURE you support the black light shield as you remove these screws so it will not fall on the floor. The black light tube may be replaced at this time. BE CAREFUL NOT TO DROP IT.
To reinstall the black light shield, reverse this procedure. O Replacing the black light tube starter. See Figure 3-7,
O Replacing the black light tube starter. See Figure 3-7, Be sure the power to the game has been turned off. Grasp the starter (it is on the back of the mounting bracket, give it a quarter turn, and remove it from its socket. To replace the fluorescent light tube starter, reverse this procedure.
BLACK LIGHT SHIELD
FRONT SERVICE PANEL
Figure 3-8 Servicing Center Auxiliary Lighting

This page is a drawing, shown as the original scan.
4-2 ®B ©@@Q OOO ® © ® ® © ©OOO00®2© © © NO. 639 — KOZMIK KROOZ’R — FRONT
NO. 639 — KOZMIK KROOZ’R — FRONT — PARTS LIST
ORDER BY PART NUMBER ONLY | irem | PART NO. DESCRIPTION 0639-00909-00XF DISPLAY HEADER A639-00030-0000 HEADER FLUOR. LIGHT ASSY. 0537-00903-0066 GLASS CHANNEL — 5-7/8" LG. (2 REQ'D.) 0537-00903-0004 GLASS CHANNEL — 22-1/4" LG. 0574-00903-0100 HEADER RETAINING BRKT. 0639-00111-00XF RETAINER GRILL 0017-00101-0138 #8 x 5/8 TORX TAMPER RESISTANT BLK. SCR. (16 REQ’D.) 0017-00003-0430 6" x 9" SPEAKER — 4 OHM, 10W. (2 REQ'D.) 0017-00101-0127 #8-32 x 1-1/2 CARRIAGE BOLT (8 REQ'D.) 0017-00103-0061 #8-32 HEX NUT W/SEMS (8 REQ’D.) A639-00055-0000 SPEAKER CABLE ASSY. 0639-00907-00XF MAIN VIEWING GLASS 0537-00903-0068 GLASS CHANNEL — 17” LG. (2 REQ'D.) 0537-00903-0034 GLASS CHANNEL — 23” LG. 0639-00102-00XF DISPLAY GLASS RETAINER BRKT. 0639-00100-00XF LAMP PROTECTOR MTG. BRKT. 0639-00902-0000 LAMP PROTECTOR 0017-00101-0138 #8 x 5/8 TORX TAMPER RESISTANT BLK. SCR. (10 REQ’D.) A639-00031-0000 BLACK LIGHT ASSY. A639-00054-0000 ACCESS PANEL ASSY. A639-00041-0000 OVERLAY TO WELDMENT ASSY. A639-00042-0000 CONTROL SHELF WELDMENT ASSY. 0639-00919-0000 DECORATIVE OVERLAY 0639-00124-0100 CONTROL SHELF MTG. BRKT. — LEFT 0639-00124-0200 CONTROL SHELF MTG. BRKT. — RIGHT 0555-00901 -0000 PLASTIC LOCATING PIN (4 REQ’D.) 0017-00009-0534 BASSICK CLAMP (3 REQ’D.) 0017-00101-0141 #8 x 11/16 UNSLOT. HEX HD. SCR. (12 REQ'’D.) 0639-00127-0000 CONTROL SHELF LOCK BRKT. A639-00034-0000 KNOB & SHAFT ASSY. A639-00043-0000 OPTICAL ENCODER DISC ASSY. A628-00032-0000 GRIP W/SWITCH ASSY. A639-00023-0000 ANALOG CONTROL ASSY. A089-00020-0000 CONTROL GRIP CABLE ASSY. — 16” LG. A639-00008-0000 CONTROL SHELF CABLE ASSY. 0017-00042-0260 PUSH BUTTON ASSY. — WHITE (2 REQ'’D.) 0017-00032-0093 PUSH BUTTON SWITCH W/HOLDER (2 REQ’D.) 0017-00103-0054 5/8-11 PAL NUT (2 REQ'D.) 0639-00920-0200 DECAL — LEFT SIDE 0639-00920-0100 DECAL — RIGHT SIDE (NOT SEEN) A090-00300-11BK U.S.A. 25¢ DOUBLE COIN DOOR ASSY. A982-00015-0000 COIN DOOR CABLE ASSY.
NO. 639 — KOZMIK KROOZ’R — FRONT — PARTS LIST (Continued)
ORDER BY PART NUMBER ONLY
ITEM PART NO. DESCRIPTION
0090-00002-04BK LARGE COIN DOOR FRAME 0017-00101-0121 #6-32 x 5/16 PHIL. TRS. HD. SCR. (3 REQ’D.) {MOUNTS COIN DOOR TO FRAME) 0950-00004-0000 COIN BOX ASSEMBLY A950-00006-0000 COIN BOX CRADLE ASSY. 0950-00105-0000 COIN BOX COVER 0950-00104-0000 COIN BOX HANDLE 0950-00101-0000 COIN DEFLECTOR (2 REQ’D.) 0950-00900-0000 LARGE PLASTIC COIN BOX 0950-00103-0000 COIN BOX DIVIDER — OPTIONAL 0017-00101-0142 1/4-20 x 1-3/8 BLACK RND. HD. BOLT (4 REQ’D.) 0017-00104-0014 7/8" DISH WASHER (4 REQ’D.) 0017-00103-0018 1/4-20 HEX NUT (4 REQ'D.) A639-00032-0000 STEP STOOL ASSY. 0639-00910-0000 STEP STOOL MAT 0017-00102-0048 3/8-16 x 2" LEG LEVELERS (4 REQ’D.) 0017-00103-0026 3/8-16 LEG LEVELER HEX NUTS (4 REQ’D.)
4-4
NO. 639 — KOZMIK KROOZ’R — UPRIGHT HEADER FLUORESCENT LIGHT ASSY. & BLACK LIGHT ASSY.
NO. 639 — KOZMIK KROOZ’R — UPRIGHT HEADER FLUORESCENT LIGHT ASSY. & BLACK LIGHT ASSY. — PARTS LIST
ORDER BY PART NUMBER ONLY
PART NO. DESCRIPTION
0639-001 13-0000 0639-00107-0000 0017-00003-0043 0017-00003-0095 0017-00003-0445 0017-00031-0036 0017-00003-0412 0017-00101-0573 0017-00104-0009 0017-00003-0019 0017-00003-0026 0017-00101-0598 A961-00042-0000 HEADER FLUORESCENT BRKT. BLACK LIGHT BRKT. 18” COOL WHITE FLUOR. LIGHT LAMP 18" BLACK LIGHT LAMP LAMP LOCKS (2 REQ’D.) FLUORESCENT SOCKET (2 REQ'D.) FLUORESCENT STARTER HOLDER W/LEADS #6-32 x 1/2 PHIL. RND. HD. M.S. (4 REQ'D.) #6 EXT. WASHER (4 REQ'D.) FLUORESCENT STARTER BALLAST #8-32 x 5/16 SLT. HEX HD. SCR. (4 REQ’D.) LINE FILTER ASSY.
4-6 NO. 639 — KOZMIK KROOZ’R — REAR ACCESS
NO. 639 — KOZMIK KROOZ’R — REAR ACCESS — PARTS LIST ORDER BY PART NUMBER ONLY
PART NO. DESCRIPTION A945-00038-0000 | ON-OFF SWITCH & PLATE ASSY. 0894-00913-0000 | RECESSED HAND LIFT (2 REQ'D.) 0017-00101-0138 | #8 x 5/8 TORX TAMPER RESISTANT BLK. SCR. (12 REQ’D.) 0017-00003-0339 }| ELECTROHOME — 19” COLOR DUAL SYNC HORIZ. MTG. MONITOR (OR) 0017-00003-0439 }| WELLS-GARDNER — 19” COLOR DUAL SYNC HORIZ. MTG. MONITOR (OR) 0017-00003-0454 | ZENITH — 19” COLOR DUAL SYNCH HORIZ. MTG. MONITOR 0550-00100-0000 | MONITOR RAIL (2 REQ’D.) 0555-00901-0000 | PLASTIC LOCATING PIN (4 REQ’D.) 0017-00101-0141 #8 x 11/16 UNSLOT HEX HD. MS. (8 REQ’D.) 0017-00102-0066 | 1/4-20 x 3/4 UNSLOT. HEX HD. BOLT (4 REQ’D.) 0017-00104-0014 | 7/8” DISH WASHER (4 REQ’D.) 0639-00908-0000 | MONITOR BEZEL 0639-00901-0000 | CURVED GLASS MIRROR 0639-00112-00xF }| MIRROR HOLD DOWN BRKT. (2 REQ'D.) 0639-00905-0000 | DEEP SPACE SCENERY A639-00045-0000 | SHIP ASSEMBLY — NOT SEEN 4639-00039-0000 | ADJUSTMENT BRKT. ASSY. A639-00037-0000 | SPOT LIGHT ASSY, — NOT SEEN (2 REQ'D.) A088-00016-0000 }| INTERLOCK SWITCH & SPRING BRKT. ASSY. (2 REQ’D.) A084-90509-C000 | SOLID STATE RELAY PC. BOARD ASSY. A082-90910-E000 | DUAL POWER AMP P.C. BRD. ASSY. 0017-00042-0014 1/8” SNAP BUSHING (4 REQ'D.) 0017-00101-0751 #5-40 x 1/4 PHL. RND. HD. MSS. (4 REQ’D.) A082-90412-D000 | POWER SUPPLY P.C. BOARD ASSY, 0624-00902-0100 | P.C. SUPPORT BRKT. — 12” LG. (2 REQ'D.) 0624-00902-0500 P.C. SUPPORT BRKT. — 6-1/2" LG. (2 REQ’D.) 0317-00102-0000 P.C. MTG. BRACE BRKT. (4 REQ'D.) 0017-00101-0141 #8 x 11/16 UNSLOT HEX HD. M.S. (12 REQ'D.) 0017-00104-0037 | #8 FLAT WASHER (12 REQ’D.) A639-00005-0000 | CARD RACK W/BOARDS ASSY. A084-90010-A639 | _C.P.U. P.C. BOARD ASSY. A084-91399-A639 } VIDEO/GENERATOR P.C. BOARD ASSY. Ag84-91483-A639 | SOUND I/O P.C. BOARD ASSY. A639-00060-0000 }| SHIELD & BARRIER ASSY. A639-00059-0000 | INNER SHIELD & SPACER ASSY. A639-00061-0000 } OUTER SHIELD & SPACER ASSY. 0017-00101-0134 | #6-32 x 1/4 PHIL. RND. HD. M.S. (8 REQ'D.) 0017-00101-0153 | #6-32 x 1” PHIL. RND. HD. MS. (4 REQ’D.) A945-00020-0000 | POWER CHASSIS ASSY. — 125VA., 115V. A961-00007-0000 | CASTER ASSY. (2 REQ’D.) A945-00019-0000 | LINE CORD Assy. ADDITIONAL PARTS LIST A097-00008-0000 BACK DOOR LOCK ASSY. (2 REQ’D.) 0017-00009-0490 5-5/8" SQR. VENT GRILL — BACK DOOR (4 REQ'D.) A639-00010-0000 MASTER CABLE W/BRKT. ASSY. A639-00012-0000 HIGH VOLTAGE CABLE ASSV. A941-00008-0000 LOW VOLTAGE CABLE ASSY. A337-00018-0000 VIDEO SIGNAL CABLE ASSY.
4-7
NO, 639 — KOZMIK KROOZ’R — SHIP ASSEMBLY
NO. 639 — KOZMIK KROOZ’R — SHIP ASSEMBLY — PARTS LIST
ORDER BY PART NUMBER ONLY
ITEM PART NO. DESCRIPTION
0639-0091 8-0000 KOZMIK KROOZ'R 0639-00929-0000 COCKPIT 0639-00927-0000 DECAL (3 REQ’D.) 0639-00912-0000 CANOPY A639-00051-0000 0017-00101-0159 0017-00042-0327 0639-00917-0000 A080-91478-8639 0017-00031-0051 0017-00031 -0046 0017-00003-0463 0017-00101-0001 0639-007 10-O0XF 0017-00100-0031 0017-00100-0025 0017-00104-0094 0017-00103-0069 0639-00914-0000 A639-00047-0000 A639-00038-0000 A639-00040-0000 A084-91434-D639 0017-00642-0326 0017-00101-0014 0639-00923-0000 A639-00056-0000 0017-00101-0528 0639-001 18-00XF 0639-00121-00XF 0010-00603-0000 0017-00101-0665 0017-00101-0656 A639-00039-0000 KOZMIK KROOZ'R BODY ASSY. (FIRST 3 ITEM NO’S.) #4 x 1/2 PHIL. RND. HD. BLACK SCREW (3 REQ’D.) PLASTIC GROMMET (3 REQ’D.) KOZMIK KROOZ’R MTG. BASE LAMP P.C. MTG. BOARD WEDGE BASE SOCKET W/LEAD WEDGE BASE SOCKET (2 REQ'D.) WEDGE BASE LAMP — 14V. (3 REQ’D.) #4 x 1/4 PHIL. PAN HD. SCR. (4 REQ'D.) SPINDLE 5/16" E-RING (2 REQ’D.) 1/4" E-RING (2 REQ’D.) PLASTIC FLAT WASHER (3 REQ’D.) 5/16-24 HEX NUT (2 REQ’D.) GEAR GEAR & FLAG ASSY. ADAPTOR ASSY. MTG. BRKT. ASSY. SENSOR P.C. BRD. ASSY. PLASTIC GROMMET (2 REQ’D.) #6 x 1/2 SLT. HEX HD. SCR. (2 REQ’D.) P.C. BRD. SHIELD MOTOR & CONNECTOR ASSY. #5-40 x 3/4 PHIL. RND. HD. M.S. (2 REQ’D.) MTG. BRKT. ADJUSTER EXTENSION SPRING (2 REQ’D.) #10-32 x 7/8 UNSLOT. HEX HD. WHZ. BOLT. #10-32 x 1/2 SLT. PAN HD. SCREW (2 REQ’D.) ADJUSTMENT BRKT. ASSY. (ITEMS 27 THRU 31)
NO. 639 — KOZMIK KROOZ’R — ANALOG CONTROL ASSY.
@) 0) Qs) ) @ @) (6) Gi) @)
NO. 639 — KOZMIK KROOZ’R — ANALOG CONTROL ASSY. — PARTS LIST
ORDER BY PART NUMBER ONLY
ITEM PART NO. DESCRIPTION
0873-00900-0400 CONTROL GRIP — LEFT 0873-00900-0300 CONTROL GRIP — RIGHT 0639-00926-0000 LENS 0628-00906-0000 TRIGGER A628-00028-0000 LEAF SWITCH ASSY. 0020-00202-0000 SWITCH PLATE 0017-00101-0528 #5-40 x 3/4 PHIL. RND. HD. M.S. (2 REQ’D.) 0873-00123-00XF SWITCH MTG. BRKT. 0017-00101-0083 #4-20 x 3/8 PHIL. PAN HD. SCR. (2 REQ’D.) 0017-00101-0149 #10-32 x 3/8 TORX TAMPER RESISTANT BUTTON HD. SCREW (5 REQ'D.) TUBING & PIVOT PIN — PINNING ASSY. SLEEVE — NOT SEEN SLIDE BUMPER MTG. BRKT. BUMPER — 8 POSITION #8-32 x 3/8 SLT. PAN HD. M.S. (4 REQ'D.) CENTERING BRKT. WELD ASSY. GROMMET FLAT WASHER 7/16-14 NYLON INSERT LOCKING NUT ACTUATING PIN PIVOT BUSHING 5/32 E-RING #10-32 x 3/8 SLT. HEX HD. SCREW (4 REQ'D.) #10-32 HEX NUT W/SEMS (4 REQ’D.) #8-32 x 5/16 SLT. HEX HD. SCR. (10 REQ’D.) WEAR PLATE BRKT. WEAR PLATE SLIDE & MTG. BRKT. RIVET ASSY. ANALOG JOYSTICK P.C. BRD. ASSY. ACTUATING BRKT. ASSY. — UPPER ACTUATING BRKT. ASSY. CORE (2 REQ’D.) #4-40 HEX NUT (2 REQ'’D.) EXTENSION SPRING (2 REQ'’D.) P.C. MTG. POST (4 REQ'’D.) #6-32 x 5 SLT. PAN HD. M.S. (8 REQ’D.) CONTROL GRIP CABLE ASSY. — 16" LG. SPRING EXTENSION STRAIN RELIEF 2 PIN CONNECTOR A639-00025-0000 0628-00921-0000 0628-00904-0000 0873-001 13-00XF 0639-00903-0000 0017-00101-0615 A639-00020-0000 0628-00905-0000 0017-00104-0034 0017-00103-0082 0639-00700-00XF 0873-00706-00XF 0017-00100-0015 0017-00101-0799 0017-00103-0081 0017-00101-0598 0639-00108-0000 0639-00906-0000 A639-00013-0000 A084-91458-E000 A639-00014-0000 A639-00015-0000 0069-264XX-XBYX 0017-00103-0002 001 0-00268-0000 0639-00701-O0XF 0017-00101-0755 A089-00020-0000 0010-00266-0100 0017-00021-0299
4-12 NO. 639 — KOZMIK KROOZ’R — KNOB & SHAFT — ENCODER DISC ASSY.
NO. 639 — KOZMIK KROOZ’R — KNOB & SHAFT — ENCODER DISC ASSY. — PARTS LIST
ORDER BY PART NUMBER ONLY [rem | PART NO. DESCRIPTION A639-00034-0000 KNOB & SHAFT ASSY. 0639-00925-0000 KNOB INSERT LABEL 0017-00100-0050 1/2” E-RING (2 REQ’D.) 0017-00104-0045 FLAT WASHER 0017-00104-0079 PLASTIC WASHER A639-00035-0000 BEARING TO BUSHING ASSY. 0639-00704-00XF MAIN SHAFT A639-00048-0000 SENSOR DISC ASSYV. 0017-00101-0791 #8-32 x 1/4 HEX CUP SET SCREW (2 REQ'D.) 0639-00705-00XF STOP STUD 0639-0091 1-0000 ROLLER SLEEVE 0639-00114-0000 SWITCH MTG. BRKT. 0017-00101-0124 #6 x 1/4 UNSLOT. HEX HD. M.S. (4 REQ'D.) A639-00058-0000 LEAF SWITCH ASSY. 0020-00202-0000 SWITCH PLATE 0017-00101-0527 #5-40 x 5/8 PHIL. RND. HD. SCR. (2 REQ'D.) 0531~-00106-0000 P.C. MTG. BRKT. 0017-00101-0586 #8-32 x 3/16 SLT. PAN HD. MS. (2 REQ’D.) A084-91482-A000 OPTICAL ENCODER P.C. BRD. ASSY. 0017-00042-0072 PLASTIC GROMMET (4 REQ'D.) 0017-00101-0018 #6 x 3/4 SLT. HEX HD. WD. SCR. (4 REQ’D.)
KOZMIK KROOZ’R — POWER CHASSIS ASSY. — 125VA., 115V.
KOZMIK KROOZ'R — POWER CHASSIS ASSY. — 125 VA., 115V. — PARTS LIST
ORDER BY PART NUMBER ONLY
ITEM PART NO. DESCRIPTION
| 1 | 0945-00104-00XF | CHASSIS |
| 2 | A945-00029-0000 | MTG. PLATE & BARRIER ASSY. |
| 3 | 0945-00107-01XF | STRAP (2 REQ’D.) |
0017-00101-0123 #8 x 1/4 UNSLOT. HEX HD. SCR. (12 REQ'D.) MT0G-00101-A000 ISOLATION TRANSFORMER W/O SHIELD ASSY. — 115V., 50/60 HZ. 0017-00103-0061 #8-32 HEX NUT W/SEMS (4 REQ’D.)
| 6 | MT00-00099-A000 | POWER TRANSFORMER ASSY. — 115V., 60 HZ. |
0017-00103-6084 #6-32 HEX NUT W/SEMS (4 REQ’D.)
| 7 | 0175-181T4-GXJK | CAPACITOR — 3.5 M-F., 440V. |
| 8 | 0017-00009-0535 | CLAMP |
0017-00101-0565 #6-32 x 7/16 SLT. PAN HD. SCR. 0017-00103-0084 #6-32 HEX NUT W/SEMS
| 9 | 0017-00101-0067 | #6 x 3/8 PHIL. PAN HD. SCR. (11 REQ’D.) |
0945-00103-00XF PARTITION — LOCATED UNDER CHASSIS (NOT SEEN)
| 10 | 0945-00902-0000 | SNAP BUSHING (3 REQ’D.) |
| cn) | 0017-00021-0297 | 2 POSITION CONNECTOR |
| 12 | A945-00030-0100 | CONNECTOR & CABLE ASSY. #1 |
| 13 | A945-00030-0200 | CONNECTOR & CABLE ASSY. #2 |
| 14 | A945-00021-0000 | CONVENIENCE OUTLET ASSY. |
| 15 | 0017-00101-0573 | #6-32 x 1/2 PHIL. RND. HD. SCR. (2 REQ'’D.) |
0017-00103-0084 #6-32 HEX NUT W/SEMS (2 REQ’D.} A945-00025-0000 FILTER ASSEMBLY — 125V. — UNDER GHASSIS (NOT SEEN)
| 16 | 0017-00021-0510 | TERMINAL STRIP |
| W | 0017-00101-0140 | #4-40 x 5/16 PHIL. PAN HD. SCR. (2 REQ'D.) |
| 18 | 0017-00003-0263 | SLO-BLO FUSE — 4A., 250V. |
0017-00003-0005 FUSE —- 2A., 250V. 0017-00003-0444 QUICK CONN. FUSEHOLDER (2 REQ’D.) — FOR ABOVE FUSES 0945-00816-1902 CAPACITOR — 100,000 M.F. 0945-00816-1901 CAPACITOR — 55,000 M.F. 0017-00104-0107 #10 FLAT WASHER (4 REQ'’D.) 0017-00103-0081 #10-32 HEX NUT W/SEMS (4 REQ’D.) 0017-00009-0422 CLAMP (2 REQ'D.) 0017-00101-0758 #8-32 x 3/4 PHIL. RND. HD. SCREW (2 REQ’D.) 0017-00103-0061 #8-32 HEX NUT W/SEMS (2 REQ'D.) 0017-00101-0067 #6 x 3/8 PHIL. PAN HD. SCR. (6 REQ’D.) 0945-00904-0000 5 POSITION FUSE HOLDER 0017-00003-0263 SLO-BLO FUSE — 4A., 250V. 0017-00003-0217 SLO-BLO FUSE — 2.5A., 250V. (2 REQ'D.) 0017-00003-0007 SLO-BLO FUSE — 3A., 250V. (2 REQ’D.) 0945-00903-0000 FUSE HOLDER BARRIER A945-00022-0000 HEATSINK & DIODE ASSY. 0017-00101-0067 #6 x 3/8 PHIL. PAN HD. SCR. (2 REQ’D.) 0017-00101-0780 #6 x 1/2 PHIL. PAN HD. SCREW (2 REQ’D.) 0017-00021-0629 5 POSITION TERMINAL STRIP — (UNDER CHASSIS) A945-00019-0600 LINE CORD ASSY. — 115V. (NOT SHOWN) A945-00030-0500 CONNECTOR & CABLE ASSY. 0017-00101-C660 #10-32 x 3/4 PAN HD. SCREW 0017-00104-0107 #10 FLAT WASHER 0017-00103-6081 #10-32 HEX NUT W/SEMS
FRONT DOOR ASSEMBLY — U.S.A. 25¢
FRONT DOOR ASSEMBLY — U.S.A. 25¢ — PARTS LIST
ORDER BY PART NUMBER ONLY
PART NO. DESCRIPTION
0090-00002-04BK DOUBLE ENTRY COIN DOOR FRAME 0017-00101-0121 #6-32 x 5/16 PHIL. TRS. HD. SCR. (3 REQ'D.) A090-00073-02BK DOUBLE ENTRY COIN DOOR W/DRESS PLATE 0017-00101-0123 #8 x 1/4 UNSLOT. HEX HD. SCREW (12 REQ’D.) 0017-00007-0019 KEY HOOK 0017-00103-0059 PUSH NUT (4 REQ’D.) 0090-00912-0000 COIN ENTRY PLATE — 25¢ (2 REQ’D.) A097-00005-0000 DOOR LOCK & KEY W/SCREW & NUT (OR) A097-00006-0000 DOOR LOCK & KEY W/SCREW & NUT 0090-00128-00XF DOOR TILT SWITCH BRKT. 0017-00005-0225 DOOR CAM A090-00095-0000 DOOR TILT SWITCH 0090-00126-03XF SWITCH BACK-UP PLATE 0017-00101-0525 #5-40 x 9/16" PHIL. HD. M.S. (2 REQ’D.) A090-00096-0000 DOOR TILT SWITCH & BRKT. ASSY. (ITEMS 9 & 11 THRU 13) 0090-00903-9500 25¢ WINDOW (2 REQ’D.) 0090-00143-00XF COIN PLEX RETAINER 0017-00003-0219 12 VOLT LAMP — G.E. #194 (2 REQ'D.) 0017-00031-0048 WEDGE SOCKET W/BRKT. (2 REQ'D.) A090-00100-0000 BRKT. ASSY. 0017-00103-0084 #6-32 HEX NUT W/SEMS (4 REQ'D.) A090-00089-0000 COIN METER W/DIODE 0017-00101-0124 #6 x 1/4 UNSLOT. HEX HD. SCR. (4 REQ’D.) 0090-0091 1-0009 INSULATOR (2 REQ’D.) A090-001 12-0000 COIN CHUTE & TOP ASSY. (2 REQ'’D.) 0010-00134-0000 SPRING 0010-00181-0000 SPRING 0017-00007-0083 1/8 x 1-5/8 ROLL PIN (0090-00129-00XF PIVOT POST 0090-00167-00XF PIVOT LEVER 0090-00182-00XF REJECT LEVER 0017-00100-0018 E-RING A090-00088-0000 REJECT LEVER ASSY. (2 REQ'D.) (ITEMS 30 THRU 33) A090-00105-0000 COIN ACCEPTOR FRAME ASSY. (2 REQ'D.) 0017-00005-0003 COIN ACCEPTOR W/STRING CUTTER (2 REQ'’D.) (OR) 0017-00005-0211 COIN ACCEPTOR W/ANTI STRING DEVICE (2 REQ'D.) (OR) 0017-00005-0214 COIN ACCEPTOR W/STRING CUTTER (2 REQ’D.) A090-00064-0000 ANTI-PENNY DEVICE 0017-00101-0099 #6 x 1/4 SLT. HEX HD. M.S. (2 REQ'D.) 0090-00162-00XF COIN SWITCH MTG. BRKT. 0017-00005-0203 COIN SWITCH CHUTE 0017-00005-0195 COIN SWITCH 0010-00599-0000 COIN SWITCH WIRE 0017-00007-0015 PUSH-ON RING A090-00059-0400 COIN SWITCH & WIRE ASSY. (ITEMS 40 THRU 42) 0017-00101-0147 #4-40 x 3/4 PHIL. PAN. HD. M.S. (2 REQ'D.) A090-00077-0000 COIN GUIDE & SWITCH ASSY. (ITEMS 38 THRU 43) OCMONMAMH AWN
V Technical Troubleshooting
Introduction
The most common problems occur in harness components such as the coin acceptor, player controls, interconnecting wiring, etc. The TV monitor and PCB computer cause their share of problems too, but not as much as the harness and its component parts. TV monitor troubleshooting will not be covered here because it is covered in that section of this manual. As you already know, the PCB computer is a complex device with a number of different circuits. Some circuits remain basically the same among games, but overall there are a great many differences between them. PCB troubleshooting procedures, therefore, can be lengthy and will differ greatly among games. However, some basic Z-80 CPU information is invoived in this section.
General Suggestions
The first step in any troubleshooting procedure is correctly identifying the malfunction's symptoms. This includes not only the citcuits or features malfunctioning, but also those still operational. A carefully trained eye will pick up other clues as well. For instance, a game in which the computer functions fai! completely just after money was coliected may have a quarter shorting the PCB traces. Often, an experienced troubleshooter will be able to spot the cause of the problem even before opening the cabinet. After all the clues are carefully considered, the possible malfunctioning areas can be narrowed down to one or two good suspects. Those areas can be examined by a process of elimination until the cause of the malfunction is discovered.
Harness Component Troubleshooting
Typical problems falling in this category are coin and credit problems, power problems and failure of individual features. NO GAME CREDIT For example, your prospective player inserts his quarter and is not awarded a game. The first item to check is if the quarter is returned. If the quarter is returned, the malfunction most certainly lies in the coin acceptor itself. First, use a set of test coins (both old and new) to ascertain that the player's coin is not undersize or underweight. If your test coins are also returned, coin acceptor servicing is indicated. Generally, the cause of this particular problem is a maladjusted magnet gate. Normally, this wili mean slightly closing the magnet gate alittle by turning the adjusting screw out a bit (see section on coin acceptor for more details). |f the quarter is not returned and there is no game credit, the cause of the malfunction may be in one of several areas. First try operating the coin return button; if the coin is returned, the problem is most likely in the magnet gate. Enlarge the gap according to the coin acceptor service procedures. If this does not cure the problem, remove the coin acceptor, clean it and perform the major adjustment Procedure. If the trapped coin is not returned when the wiper lever is actuated, you may have an acceptor jammed by a slug, gummed up with beer, a jammed coin chute, or mechanical failure of the acceptor mechanism. In this case, first check for the slug that wil! generally be trapped against the magnet. If so, simply remove the slug and test the acceptor. If the chute is blocked, remove the acceptor and remove the jammed coins. If there is actual failure of the acceptor, remove the unit and repair as indicated in the coin acceptor service procedures. lf the coin is making its way through the acceptor (that is, falling into the coin box), yet there is still no game credit, you either have a mechanical failure of the coin switch or electrical failure of the coin and credit circuits. The first place to begin is by checking the coin switch. Most of these switches are the make/break variety of micro switch, which is checked by testing for continuity between the NO, NC, and C terminals. When not actuated, the NC and C terminals should be continuous and the NO terminal open. When operated, the NO and C terminals should close and the NC should be open. If the coin switch checks out, examine the connections to the terminals to make sure there is good contact. If necessary, use the continuity tester and check from the terminal lug on the switch to the associated PCB trace. This will tell you if there is a continuous line all the way to the credit circuit.
If the coin switch wires do not check out, the problem is in the computer — most likely in the coin and credit circuitry. If you do get game credit when a coin is deposited, but the game will not start when the start switch is pressed, you may have a problem in the start switch, the interconnecting wiring or in the computer. First check the switch. If the switch is OK, proceed to check the wiring. Again, make sure you go from the terminal lug on the switch to the PCB trace. This way, you will check the terminal contact as well as PCB edge connector contact. If the wiring is continuous, proceed to check the PCB credit circuit. If not, check each section of the wiring, until the discontinuity is located. If the wiring is OK, the problem must lie in the computer.
Transformer and Line Voltage Problems
Your machine must have the correct line voltage to operate properly. If the line voltage drops too low, a circuit in the computer will disable game credit. The point at which the computer will fail to work will vary
some from game to game, but no game'will work on
line voltage that drops below 105 VAC. Low line voltage may have many causes. Line voltage normally fluctuates a certain amount during the day as the total usage varies. Peak usage times occur mainly at dawn or dusk, so if your machine’s malfunction seems to be related to the time of day, this may be a factor. A large load connected to the same line as the game (such as a large air conditioner or other device with an exceptionally large motor) may drop the line voltage significantly when starting up. This drop can result in an intermittent credit problem. In addition, poor connections in the location wiring, plug, or line cord may also cause a significant drop in power. Cold solder joints in the game's harness, especially in areas like the transformer connections, interlock switch, or fuse block, may also produce the same results, although probably on a more permanent basis. Sometimes location owners (especially in bars) replace light switches with dimmer rheostats, and the game is sometimes on the same line. Obviously, the voltage available to the game is going to drop dramatically when the dimmer is turned. In any case, the way to check for correct line voltage is with your VOM. Set the VOM to 250 VAC and stick the probes in the wall receptacle. If it's OK here, check the transformer primary connections. If you do not get 117 VAC, examine the solder joints on the transformer, fuse block, and interlock switch. If you do get 117 VAC, the problem must be either in the transformer, harness connections, or in the PCB power supply.
5-2 If you suspect the transformer, check its secondaries with the VOM set to 50 VAC and correlate the readings with the legend on the side of the transformer. The transformer must also be correctly grounded, so check the ground potential as well, especially if there is a hum bar rolling up or down the TV screen.
HARNESS PROBLEMS Other harness problems include blowing fuses and malfunctioning controls. The repeating blown-fuse problem can sometimes be quite exasperating to soive, for short circuits have the tendency to occur in areas almost impossible to find. First, try inserting a new fuse, as old fuses age and blow without cause. If the new one also blows, you definitely have a short. The best way to approach this problem is by turning the power off and disconnecting devices that may be causing the problem, such as the TV, transformer, and PCB. Disconnect the devices by pulling off their connectors, but do not allow them to touch. If necessary, insulate them with small pieces of electrical tape. Then, connect your VOM across the terminals of the fuse block (all electrical power shut off), and set it to one of the resistance scales. This will save blowing a fuse each time you want to check the circuit. If the VOM reveals that disconnecting the devices removed the short, reconnect the devices one by one until the short returns. The last device connected is the one that is at fault. If the VOM reads a short even after the devices are disconnected, the fault must lie in the harness itself, and only patient exploration will reveal its location. First; carefully examine all the wiring, looking for terminals that may be touching, metal objects such as coins shorting connections or burned insulation. If necessary, use the VOM to check each suspected wire. MALFUNCTIONING CONTROLS One of the most common problems here is a bad potentiometer. Typically, a bad pot will cause the image to jump as it reaches a certain point. The only cure for this one is to install a new pot. If a feature that is operated by a switch (for example, joysticks, foot pedals, control panel buttons) does not operate at all, check the switch with a VOM or continuity tester to verify its operation. If the switch does not check out, replace it. if the switch is OK, you should suspect the input to the switch from the PCB. In this case, get out the harness and iogic schematics and check to see what kind of input it is. In many cases, the input will be +5 VDC. If so, use the VOM to check its presence. Normally, the switch is used to pull a +5 VDC line LOW to GND or to pulla LOW line HIGH. If the PCB output is missing, check the wire length from the PCB. If you find the signal at the PCB trace, the wire length or connection is at fault. If not, begin exploring the PCB using the logic schematics.
A Glossary of Microprocessor Terms
MICROPROCESSOR — one or several microcircuits that perform the function of a computer's CPU. Sections of the circuit have arithmetic and comparative functions that perform computations and executive instructions.
CPU — central-processing unit. A computing system's “brain”, whose arithmetic, control and logic elements direct functions and perform computations. The microprocessor section of a microcomputer is on one chip or several chips. PROM — programmable read-only memory. User permanently sets binary on-off bits in each cell by selectively fusing or not fusing electrical links. Nonerasable. Used for low-velume applications.
EPROM — erasable, programmable, read-only memory. Can be erased by ultraviolet light bath, then reprogrammed. Frequently used during design and development to get programs debugged, then replaced by ROM for mass production.
ROM — read-only memory. The program, or binary on-off bit pattern, is set into ROM during manufacture, usually as part of the last metal layer put onto the chip. Nonerasable. Typical ROM's contain up to 16,000 bits of data to serve as the microprocessor's basic instructions. RAM — random-access memory. Stores binary bits as electrical charges in transistor memory cells. Can be read or modified through the CPU. Stores input instructions and results. Erased when power is turned off LSI — large scale integration. Formation of hundreds or thousands of so-called gate circuits on semiconductor chips. Very large scale integration (VLS) involves microcircuits with the greatest component density. MOS — metal-oxide semiconductor. A layered construction technique for integrated circuits that achieves high component densities. Variations in MOS chip structures create circuits with speed and low-power requirements, or other advantages (static will damage a MOS chip).
Introduction to the
Z-80 CPU
The term “microcomputer” has been used to describe virtually every type of small computing device designed within the last few years. This term has been applied to everything from simple “microprogrammed” controllers constructed out of TTL MSI up to low end minicomputers with a portion of the CPU constructed out of TTL LSI “bit slices.” However, the major impact of the LSI technology within the last few years has been with MOS LSI. With this technology, it is possible to fabricate complete and very powerful computer systems with only a few MOS LSI components. The Zilog Z-80 family of components can be configured with any type of standard serniconductor memory to generate computer systems with an extremely wide range of capabilities. For example, as few as two LSI circuits and three standard TTL MS1 packages can be combined to form a simple controller. With additional memory and I/O devices a computer can be constructed with capabilities that only a minicomputer could previously deliver, New products using the MOS LSI microcomputer are being developed at an extraordinary rate. The Zilog Z-80 component set has been designed to fit into this market through the following factors:
5-3
- The Z-80 is fully software compatible with the popular 8080A CPU. Existing designs can be easily converted to include the Z-80. . The Z-80 component set is at present superior in both software and hardware capabilities to any other microcomputer system on the market today. For increased throughput the Z80A operating ata 4MHZ clock rate offers the user significantspeed advantages. Microcomputer systems are extremely simple to construct using Z-80 components. Any such system. consists of three parts:
- CPU (Central Processing Unit)
- Memory
- Interface Circuits to peripheral devices The CPU is the heart of the system. Its function is to obtain instructions from the memory and perform the desired operations. The memory is used to contain instructions and in most cases data that is to be processed. For example, a typicai instruction sequence may be to read data from a specific peripheral device, store it in a location in memory, check the parity and write it out to another peripheral device. Note that the Zilog component set includes the CPU and various general purpose i/O device controllers, while a wide range of memory devices may be used from any source. Thus, all required components can be connected together in a very simple manner with virtually no other external logic.
General Purpose Registers There are two matched sets of general purpose registers, each set containing six 8-bit registers that may be used individually as 8-bit registers or as 16bit register pairs by the programmer. One set is called BC, DE and HL while the complementary set is called BC’, DE’ and HL’. At any one time the programmer can select either set of registers to work with through a single exchange command for the entire set. In systems where fast interrupt response is required, one set of general purpose registers and an accumulator/flag register may be reserved for handling this very fast routine. Only a simple exchange command need be executed to go between the routines. This greatly reduces interrupt service time by eliminating the requirement for saving and retrieving register contents in the external stack during interrupt or subroutine processing. These general purpose registers are used for a wide range of applications by the programmer. They also simplify programming, especially in ROM based systems where little external read/write memory is available. Arithmetic & Logic Unit (ALU) The 8-bit arithmetic and logical instructions of the CPU are executed in the ALU. Internally the ALU communicates with the registers and the external data bus on the internal data bus. The type of functions performed by the ALU include: Add Left or right shifts or rotates (arithmetic and logical)
Subtract Increment
Logical AND Decrement Logical OR Set bit Logical Exlusive OR Reset bit Compare Test bit Instruction Register and CPU Control As each instruction is fetched from memory, it is placed in the instruction register and decoded. The control sections performs this function and then generates and supplies all of the control signals necessary to read or write data from or to the registers, control the ALU and provide all required external control signals.
Z-80 CPU Pin Description The Z-80 CPU is packaged in an industry standard 40 pin Dual In-Line Package. The I/O pins are shown in the below figure and the function of each is described.
| (x | a7 | 30 | A |
= Ay ‘wee «=? _] 2 4,
| SYSTEM | oro | 2 a, | |
| CONTROLS | a5 | a | | Boy |
| wR | 7 | ve |
| » a,
| | RESH | 28 | 37 |
| U | = | }—— A, |
| a | ae | ADDRESS |
__ BUS
| vat | I | 2-80 CPU | [as As |
| pom A.
| —___ | 28 | 1 |
Ay
| cpu | WAIT —_——| | [> ; |
CONTROL /—» Ar.
| wr | OB | pea, | |
nm = 7 4 |—* » a,. 268 bea. RESET ————* ——_ 25 CPU ‘BUSRO a | BUS BUSAK <—~—| CONTROL a Lor bag D,
| 6 | 6 | 2 |
- 0. 1 8
| lav | mene | DATA | |
| cnn | — = | ja» v, | BUS |
byt Ds 2-80 PIN CONFIGURATION ty
5-4
Ao-Ass (Address Bus) Tri-state output, active high. Aj-A,; constitute a 16bit address bus. The address bus provides the address for memory (up to 64K bytes) data exchanges and for /O device data exchanges. |/O addressing uses the 8 lower address bits to allow the user to directly select up to 256 input or 256 output ports. Ap is the least significant address bit. During refresh time, the lower 7 bits contain a valid refresh address.
D,-D; (Data Bus) Tri-state input/output, active high. Dy-D; constitute an 8-bit bidirectional data bus. The data bus is used for data exchanges with memory and I/O devices.
My, (Machine Cycle one) _ Output, active low. M, indicates that the current machine cycle is the OP code fetch cycle of an instruction execution. Note that during execution of 2-byte op-codes, M1 is generated as each op code byte is fetched. These two byte op-codes always begin with CBH, DDH, EDH or FDH. M1 also occurs with IORQ to indicate an interrupt acknowledge cycle. MREQ (Memory Request) Tri-state output, active low. The memory request signal indicates that the address bus holds a valid address for a memory read or memory write operation. 1ORQ (Input/Output Request) Tri-state output, active low. The IORQ signal indicates that the lower half of the address bus holds a valid I/O address for al/O read or write operation. An IORQ signal is also generated with an M1 signal when an interrupt is being acknowledged to indicate that an interrupt response vector can be placed on the data bus. Interrupt Acknowledge operations occur during M, time while I/O operations never occur during M, time. RD (Memory Read) _ Tri-state output, active low. RD indicates that the CPU wants to read data from memory or an I/O device. The addressed I/O device or memory should use this signal to gate data onto the CPU data bus. WR (Memory Write) Tri-state output, active low. WR indicates that the CPU data bus holds valid data to be stored in the addressed memory or I/O device.
5-5 RFSH (Refresh) Output, active low. RFSH indicates that the lower 7 bits of the address bus contain a refresh address for dynamic memories and the current MREQ signal should be used to do a refresh read to all dynamic memories.
HALT (Halt state) Output, active low. HALT indicates that the CPU has executed a HALT software instruction and is awaiting either a non maskable or a maskable interrupt (with the mask enabled) before operation can resume. While halted, the CPU executes NOP’s to maintain memory refresh activity. WAIT (Wait) Input, active low. WAIT indicates to the Z-80 CPU that the addressed memory or I/O devices are not ready for a data transfer. The CPU continues to enter wait states for as long as this signal is active. This signal allows memory or I/O devices of any speed to be synchronized to the CPU. INT (Interrupt Request) Input, active low. The interrupt Request signal is generated by \/O devices. A request will be honored at the end of the current instruction if the internal software controlled interrupt enable flip-flop (IFF) is enabled and if the BUSRQ signal is not active. When the CPU_accepts tne interrupt, an acknowledge signal (IORQ during M, time) is sent out at the beginning of the next instruction cycle. The CPU can respond to an interrupt in three different modes that are described in detail in section 5.4 (CPU Control Instructions). NMI (Non-Maskable Interrupt) Input, negative edge triggered. The non maskable interrupt request line has a higher priority than INT and is always recognized at the end of the current instruction, independent of the status of the interrupt enabie flip-flop. NMI automatically forces the Z-80 CPU to restart to location 0066%. The program counter is automatically saved in the external stack so that the user can return to the program that was interrupted. Note that continuous WAIT cycles can prevent_the current instruction from ending, and that a BUSRQ will override a NMI.
RESET Input, active low. RESET forces the program counter to zero and initializes the CPU. The CPU initialization includes:
- Disable the interrupt enable flip-flop
- Set Register |= 00x
- Set Register R =001
- Set Interrupt Mode 0 During reset time, the address bus and data bus go to a high impedance state and ali contro! ouput signals go to the inactive state.
BUSRQ (Bus Request) input, active low. The bus request signal is used to request the CPU address bus, data bus and tri-state output control signals to go to a high impedance state so that other devices can control these buses. When BUSRQ is activated, the CPU will set these buses to a high impedance state as soon as the current CPU machine cycle is terminated. BUSAK (Bus Acknowledge) Output, active low. Bus acknowledge is used to indicate to the requesting device that the CPU address bus, data bus and tri-state control bus signals have been set to their high impedance state and the external device can now control these signals.
CLK (Clock) Single phase TTL level clock which requires only a 330 ohm pull-up resistor to +5 voits to meet all clock requirements.
MCR II SYSTEM P.C. BOARD JUMPER OPTIONS
VIDEO GENERATOR P.
SUPER C.P.U. P.C. BOARD
JUMPER OPTIONS FOR PROGRAM ROMS ONLY
MANUFACTURER EPROM NO. | Jw#2 | Jwi#a | uwas | uwee # MOTOROLA #
TA. # INTEL 2764 | * | * JW#7 | JWH#18 | JWH19 f=
JUMPER OPTIONS FOR er [we] ROMS =
MANUFACTURER EPROM NO. | JW#10 | awe Jwe12| Jw#13 | IWH14 | swt | [swe | [swer7| 68764 MOTOROLA —_— 68766
TA. 2564
INTEL 2764 . # = * #
NUMEROUS MFR'S SOUND 1/0 P. C. BOARD
NUMEROUS MFR'S ee | # | * |
- = CUT JUMPER WIRES WHERE THIS SYMBOL “*” APPEARS. # = LEAVE JUMPER WIRES !N WHERE THIS SYMBOL “#” APPEARS.
The above table illustrates the fact that the Video Generator P.C. Board used in the MCR II System has 8 jumper wires, the SUPER C.P.U. P.C. Board used in the MCR II System has 19 jumper wires, and the Sound I/O P.C. Board used in the MCR Il System has 2 jumper wires.
All of the above Boards can be used with a variety of different SETS of EPROM chips. However, these EPROMS are not all made by the same manufacturer and do have some internal differences. So, in order to make them function properly in their respective P.C. Boards, certain jumper wires on these Boards have to be cut.
The above table tells you which jumpers to cut (depending on which EPROM set you're going to use) by showing a “*” under that jumper wire's number. If there is NO “*” under a jumper wire’s number, THAT PARTICULAR JUMPER WIRE IS NOT TO BE CUT.
PLEASE NOTE:
THE INFORMATION CONTAINED IN THIS SECTION 1S TOLD iN AN EASY TO UNDERSTAND MANNER AND IS INTENDED TO AID THOSE WITHOUT AN ELECTRONICS DEGREE IN TROUBLESHOOTING AND REPAIRING THEIR GAMES T.V. MONITOR.
IF YOU READ THROUGH THIS SECTION AND STILL HAVE QUESTIONS, PLEASE CONTACT YOUR DISTRIBUTOR OR MIDWAY MANUFACTURING COMPANY AT THE TOLL FREE NUMBER PROVIDED WITH YOUR GAMES PAPERS.
OUR STAFF AND OUR DISTRIBUTORS STAND READY TO HELP YOU!
THANK YOU
Introduction: (How to
use this section of your manual.)
This section has been designed to simply familiarize you with one of the more mystical components in your game — the T.V. monitor. If you are an electronics technician who is quite knowledgeable on the subject, you may decide to just go to the schematics and start troubleshooting the defective monitor. But if you are like most people, a monitor is. a T.V. set, and that means a complex doo-dad that means big buck repairs. This isn't necessarily so. This section of the manual will acquaint you with the monitor and could just heip you repair it if you feel adventurous enough to give it a try. If you have any knowledge of electronics, especially the use of a voltmeter, the repairs you can make are astonishing. Just keep in mind that ELECTRICITY CAN BE VERY DANGEROUS, SO BE CAREFUL!!
If you want to understand how a monitor works, just read the “THEORY OF OPERATION” subsection. If you wish, you can follow along with the schematics. The information is presented in a very basic manner but a more complete treatment of the subject can be found in the technical sections of bookstores.
\f you want to attempt to repair your monitor, itwould be a good idea to read this whole section beginning to end before starting. Pay attention to all warnings
6-1 and take them seriously. The more equipment you have the better, but a low cost Volt-Ohm-Milliameter can often do the trick. Here are the steps to take:
- Find the symptom that matches the problems your monitor has in the “SYMPTOM — DIAG- NOSIS” subsection. The diagnosis tells the circuit or area the problem may be in and possibly even the actual component causing it.
- Once you have the circuit that is causing the trouble, read the “TROUBLESHOOTING” subsection to learn the procedure for finding the bad part.
- Next, go to the schematic section and find the schematic that matches your monitor. It may be helpful to read the “DIFFERENCES BETWEEN MONITORS” subsection if you are unsure of which monitor you have. Use the schematic to see what parts are in the offending circuit.
That really is all there is to it. Just remember that there are some bizarre or rare symptoms not covered, or that a monitor may have two or more different problems that only a genius, the experienced, or an experienced genius can figure out. But be patient, follow safety precautions, and remember that there is also literature available from the monitor companies through your distributor or from Bally Midway Manufacturing Company on request. (There is a toll free number on the back side of the front cover of this manuai.)
Symptom Diagnosis
. Insufficient width or heighth: A. Horizontal line (due to VERTICAL CIR- CUIT DEFECT). C Bad yoke. O Bad vertical output section. ] Open fusible resistor in vertical section. D Bad height control. 0 Bad flyback. Vertical line (due to HORIZONTAL CIR- CUIT DEFECT). O Bad yoke. O Open width coil. 0 Open part in horizontal output section. . Picture spread out too far or crushed in certain areas: A. Horizontal or vertical output transistor. B. Bad Component in output circuitry. Cc. Vertical linearity or damper control needs adjustment. . Line too close with black spacing: A. Problem in vertical section causing poor linearity. }. Poor focus and convergence: A. Bad high voltage transformer (‘‘flyback”) or control. B. Focus voltage wire not connected to neckboard terminal. . Colors missing; check: interface color transistors. Color output transistors. Cracked printed circuit board (neck Board). Color circuits. Video input jack. Defective picture tube. ™mMOOW>
. Picture not bright enough: A. Weak emission from picture tube. . Silvery effect in white areas; check: A. Beam current transistors. B. Weak picture tube emission. Too much brightness with retrace lines; check: A. Beam limiter transistors. B. Brightness and/or color blanking control set too high. . increasing brightness causes an increase in size and poor focus. A. Weak high voltage rectifier or regulation (high voltage unit). B. Bad component in monitor's power supply.
6-2 10.
11.
12.
13.
14,
15.
16.
17.
18.
19.
20. Small picture and/or poor focus: A. Low B+ voltage (power supply trouble).
Vertical rolling: A. Vertical oscillator in the IC, vertical sync. transistor, or circuit. B. No sync from logic board. C. Three pin syne. jack is loose or piugged in wrong. Horizontal line across center: A. Vertical output circuit is dead (see symptom No. 1. A.). B. Vertical oscillator is not putting out the right wave form. Picture bends: A. Horizontal sync needs adjusting. B. Magnetic or electromagnetic interference. Flashing picture, visable retrace lines: A. Broken neck board. B. Internal short circuit in the picture tube (arcing). Unsymmetrical picture or sides of picture: A. Defective yoke. No brightness, power supply operating — No high voltage for the picture tube; check: A. Horizontal oscillator. B. Horizontal amplifier and output. C. Flyback transformer (high voltage unit). No brightness, high voltage present; check: A. Heater voltage to the tube at the neck board. B. Screen-grid voltage for the tube. C. Focus voltage. D. Grid to cathode picture tube bias. No high voltage; check: For AC input to the “flyback”. Horizontal deflection stages. Flyback transformer. Yoke. Power supply. moog>
No horizontal and vertical hold; check: A. Sync transistors and circuit. B. Wires and jack from logic board to the monitor. Wavey picture — (power supply defect); check: A. Transistors, diodes, electrolytic capacitors in the power supply.
- Moving bars in picture: A. Ground connector off between monitor and logic boards. B. Defect in the power supply (see wavy picture symptom).
- Washed out piciure (see ‘picture not bright enough): A. Check video signal at the cathode pins with an oscilloscope. If there is about 80 volts” peak to peak, the picture tube has weak emission.
- Monitor won't turn on: A. Problem in the power supply: Check fuse, transistors, open fusibie resistor. B. Shorted horizontal output transistor. 24, C. Defective high voltage disabling circuit. D. Crack(s) somewhere on main chassis board.
Can't adjust purity or convergence: A. Use a degausser to demagnetize the picture tube carefully following your degausser’s instructions. Picture tube defective. Nearby equipment is electromagnetically interferring. The poles of the earth are pulling off the purity — see “A” above. Poor focus or width of picture. F. Make sure you have the correct CRT number for that brand of monitor. 59 OD
m
Guide To Schematic Symbols
THERMISTOR (POLARITY DOESN'T MATTER)
INDUCTOR, COIL, CHOKE (POLARITY DOESN'T MATTER)
(-) CATHODE
(+) ANODE
ZENER DIODE IRON CORE TRANSFORMER (SUCH AS A FLYBACK)
Ls
FUSE (POLARITY DOESN'T MATTER)
CATHODE (-)
ANODE (+)
DIODE
COLLECTOR Ke BASE ————— EMITTER $i
NPN TRANSISTOR
i VARIABLE RESISTOR, POT, CONTROL (POLARITY DOESN'T MATTER)
+
LINES ARE CONNECTED
+
LINES ARE NOT CONNECTED
COLLECTOR 4S
BASE ——— EMITTER “mT
PNP TRANSISTOR
WW
RESISTOR (POLARITY DOESN'T MATTER)
ELECTROLYTIC CAPACITOR
+
CAPACITOR (POLARITY DOESN'T MATTER)
hg = GROUND
6-4
Troubleshooting
Troubleshooting monitors requires experience, patience, and luck. The first step is to match the symptom the monitor displays to the diagnosis next to it in the “SYMPTOM-DIAGNOSIS" subsection. This will pinpoint the circuit the problem is probably in, and often the parts to check. Next, the circuit should be visually inspected to see if there are any parts broken, burned, or if something is there that shouldn't be, like a loose screw, etc. Some parts go bad before others and should be checked first. In fact, following is the general order in which parts usually go bad:
- Semiconductors (like transistors, diodes, and integrated circuits). Fusible resistors. Electrolytic capacitors. Resistors. Capacitors and coils. Always remember thata monitor can bite likea snake. Even when it is turned off, capacitors hold voltage and will discharge it to you should you be touching chassis ground. The picture tube or CAT, itself, is a giant capacitor, so avoid the flyback anode plug hole. With the monitor on, the power supply circuit and/or the flyback, which puts out at least 23,000 volts, CAN BE KILLERS!! Avoid handling power transistors (usually output transistors) or ICs, yoke terminals, and other high power components when the monitor is on.
6-5 Be prepared for a fairly loud pop and a flash. The longer the monitor has been turned off, the smaller the pop and dimmer the flash. But BE CARE- FUL, picture tubes will hoid a very healthy charge for at least a week if not longer. Even after you've discharged it once, it may still carry a residual charge. It’s better to be too careful than dead, which is why electronic equipment always carries stickers referring servicing to qualified personnel. Handle the side with the viewing screen against your chest when changing it. ALWAYS wear safety goggles when handling the picture tube. To maintain the safety and performance of the monitor, always use exact replacement parts. For instance, the wrong components in the power suppiy can cause a fire, or the wrong color transistor may give a funny color to the picture. Service your Monitor on a nonconductive firm table like wood, NOT METAL, and take off all of your jewelry just in case. With all this in mind, you are ready to begin troubleshooting.
Observe the picture carefully. Try to vary the appropriate control that would most likely affect your particular symptom. For example, if there is poor brightness or no picture, try turning up the brightness or contrast control. If the controls have no effect at all, chances are there is trouble with the control itself, the circuit it controls, or a nearby circuit that may be upsetting voltages. Go to the list of symptoms and determine with the schematic where the bad circuit is.
Keep in mind that capacitors hold a charge as can the picture tube (for at least a week and usually longer), and could shock you.
First, check for obvious visual defects such as broken or frayed wires, solder where it is not supposed to be, missing components, burned components, or cracked printed circuit boards. If everything looks good up to this point, make sure that diodes, electrolytic capacitors, and transistors have their leads connected in the right polarity as shown on the schematic and the circuit board. Turn on the power and measure the voltages at the leads of the active devices such as tubes, transistors, or integrated circuits. Any voltage that does not come within at least 10% to 15% of the voltage specified on the schematic indicates either a problem with that device or a component connected with it in the circuit. The next step is to use the ohmmeter to narrow down the field of possible offenders.
To test a transistor, one lead of the ohmmeter is placed on the base; and the other lead placed just on the emitter, then on the collector. A normal transistor will read either high resistance (infinite), or little resistance (400 to 900 ohms), depending on the polarity of this type transistor. Then the leads should be switched, one remaining on the base, and the other switched from the emitter to the collector. Now the opposite condition should result: the resistance should be infinite if it was lower when the other lead was on the base. Consistantly infinite readings indicate an open, and a short is demonstrated by 0-30 ohms on most of these test readings. Finally, place one lead on the collector, then the other on the emitter. No matter which lead is used, there should be infinite resistance. Any lower reading, such as 50 ohms (which is typical on a bad transistor), indicates a short. This all sounds pretty confusing, but a little experience on a good transistor will make you an expert in no time, Usually, the lowest ohmmeter setting is used for testing transistors. Once in a great while a transistor may check out good on this test, but may actually be “leaky” or break down only on higher voltages. If in doubt, change it. It is also wise to check the transistor out of the circuit just in case some component in the circuit is affecting the ohmmeter reading. A diode is tested like a transistor except it only has two leads. Again, there should be high resistance one way and little resistance the other. If it tests bad, take one lead out of the circuit in case some componentis messing up the ohmmeter reading.
Without special equipment, integrated circuits are checked by verifying the proper DC voltage on the pins and the correct AC wave form using an oscilliscope. BE CAREFUL: Shorting their pins can easily destroy them. Resistors are checked with an ohmeter and should usually be within ten percent of the value stated on them and on the schematic. You may have to desolder one lead from the printed circuit board. If you wreck the foil on the board, carefully solder a small wire over the break to reconnect the conductive foil. Capacitors are tricky. Their resistance goes up when checked with an ohmmeter which shows a charging action. As they suck up current from the meter, the voltage goes up and so does the resistance. If you are sure a particular circuit is giving you a problem and everything else checks out O.K., Electrolytic capacitors are prime suspects. Substitute a new one and keep your fingers crossed.
Theory of Operation
To understand what goes on inside the monitor, large general groups of circuits will be examined instead of laboriously analyzing the branches and small circuits that make up these groups. This will help avoid confusion and aid in a basic, concrete, knowledge of what makes up a monitor.
THE POWER SUPPLY — The AC going to the monitor from the game transformer is just like the voltage and current from your wail outlet. It jumps up and down going positive and negative sixty times a second. But a monitor needs nice, smooth DC; direct current, not alternating. So diodes chop up the AC and a big electrolytic capacitor filters it out to make it even smoother. Since the monitor is a big piece of electronic equipment, with many circuits demanding a lot of power from the power supply, there are also zener diodes and transistors to help maintain a nice, constant, smooth voltage so that the monitor circuits don't jump around. And this is what happens when you see a wavy picture. There is AC creeping through the power supply, so it must be maifunctioning. If the voltage from the power supply is too iow, the other circuits will be starved for power and you may see a small, wavy picture, or noneatall. Some circuits receive voltages that are higher than what the power supply should put out. But they come from the flyback transformer which will be discussed later.
THE INTERFACE SECTION OF THE CHASSIS — The interface section of the chassis is fairly easy to identify. It is right by the place where the video jack{s) from the logic board(s) plug into. There are sets of transistors that receive the separate red, green, blue, and sync information from the cables that come from the logic boards. The circuits jack up the voltage and match impedances, or in other words, prepare the logic board outputs for the circuits that will really amplify them for the output devices such as the yoke in the case of the sync, or the picture tube that shows the colors.
An interesting aside is that our sync is composite negative sync. That means two things: 1, The sync is a negative going wave form.
- There are two pulses going at different speeds over the same wire: a, Vertical wave forms at 60 times per second (or Hertz) and b. Horizontal wave forms at about 15,750 times per second (Hz). The sync is amplified by a sync amplifier transistor and sent on its way to the oscillators. The syne or timing information will be explained along with the oscillator shortly. The color information is sent via wires to the neck board where the main amplification occurs. This wiil also be discussed later.
VERTICAL AND HORIZONTAL DEFLECTION— After the sync signal is amplified by the sync amp, it goes to two different sections, the vertical and horizontal circuits. Basically, the sync signals are for timing so the picture doesn't mess up since it is assembled like an orderly jigsaw puzzle, but so fast that you can’t see the electron beams for each color painting the picture on the screen. This will all become clear soon. For now, we will follow the 60 cycle component of the sync as it goes on its journey to the deflection yoke. The 60 cycle pulse goes to the vertical oscillator to make sure this circuit goes back and forth (or oscillates) at 60 times a second. Without this pulse keeping the circuit at the correct speed, it may get lazy and oscillate at 58 cycles or lower, or get ambitious and oscillate at 62 cycles or higher. At the wrong speed, the picture will start to roll up or down. A Wells Gardner 13” (K4806) or 19" (K4906, K4956) color monitor uses an integrated circuit for its sync section. An Electrohome 13” or 19" color monitor uses an integrated circuit |C501 for its sync section. The Zenith monitor (CD19MXRFO6) also uses an IC for the sync processing. Weils Gardner uses HA11423, Electrohome uses HA11244, and Zenith uses 221-175 (their part number). These ARE NOT interchangeable! The idea is all the same. The output to the vertical amplifying transistors for all monitors must form a sawtooth wave form, sort of like a bunch of pyramids, racing through the yoke's vertical coils at 60 times a second. Along the way to the output transistors, the 60 cycle pulse is shaped and amplified to do the job: the yoke magnetically pushes the electron beam to fill the screen out sideways looking at the screen with the greatest length going up and down. Or viewing the screen sitting like a home television set, the amplified vertical output fills the screen up and down. Watching a monitor like this, seeing only a horizontal line means a problem with the vertical coils of the yoke or anything from the vertical output section on back to the oscillator. The horizontal section is very similar with a few exceptions. The horizontal wave shape is more like a square and has a frequency of 15,750 cycles a second. Both Wells Gardner and Electrohome use the other side of their respective integrated circuits for the horizontal circuitry. If the oscillator isn’t going at the correct speed, the picture may move sideways, start to slant, or tear up with slanted thin figures. With both the vertical and horizontal of all monitors, there are variable resistors that change the speed of the oscillators up and down. This way you have controls that can make the correct frequencies to keep the electronic jigsaw puzzle nicely locked in place. If you're driving in acar and next to you someone else is driving their car at exactly the same speed, it will appear that they are not moving. And this is why the sync frequency and the oscillators frequency must match, so the picture doesn’t appear to move. The correct wave form is shaped and amplified in the circuitry just like in the vertical section. But the horizontal output transistor is a large power transistor and not only serves to give current to the horizontal yoke windings, it also feeds the flyback transformer. THE FLYBACK TRANSFORMER (OR HIGH VOLTAGE UNIT) — The picture tube needs high voltage to light up, and the power supply can't meet this demand. The flyback transformer receives current alternating at about 15,750 times per second from the horizontal output transistor. The “flyback” jacks up its input voltage and puts out a higher voltage alternating at ihe same speed. But, in your “flyback” there are diodes that chop up the alternating voltage to make it asmooth DC output just like in the power supply. This is what goes through that thick red wire to your picture tube. THIS AREA HAS ABOUT 24,000 VOLTS ON IT AND IT CAN KILL YOU! The “flyback” may be dangerous, but it is also generous. It has extra output windings which give voltage to the heater pins of the picture tube, voltage for the vertical deflection circuits, and picture tube screen-grid voltage. So in a way, the high voltage “flyback” is like a second power supply. COLOR CIRCUITS — The color circuits are pretty straight forward. The signals go into the interface section where some amplification and impedance matching occurs. These circuits are pretty sparse and simple. Each color just has two transistors and a diode with some resistors and capacitors. From here, the AC color signal is sent by wires to the neck board. The color output circuits are on the neck board. The color signals going to the transistors are controlled by two variable resistors called drive controls. There are only two, one for the red and one for the green on
Wells Gardner and Electrohome monitors. Zenith monitors have all three: red, blue and green. The Wells Gardner and Electrohome monitor have another variable resistor in their emitter part of their color output transistors. These “cutoff controls" vary the amouni of A.C. signal that the transistor amplifies and sends to the cathodes of the picture tube. The Zenith monitor has its cutoff controls in the interface section to vary the amount of signal going to the output transistors. The more signal, the more color. If you think this is confusing, here is another little hitch. The Electrohome and Zenith monitors both have the actual A.C. picture information signal going through the emitters of the color output transistors. The Wells Gardner has the A.C. signal.going to the base of the transistors.. The blanking and beam limiting signals which come from the blanking and beam limiting transistors in the interface section go into the color output transistor base in the Electrohome and Zenith monitors, but enters into the emitter of the Wells Gardner monitor's color output transistor. Should you feel adventurous enough to look at this signa! on an oscilloscope, it should look like a square. The beam limiter helps control the brightness level, and the bianking transistor rapidly turns the picture tube on and off so that retrace lines don’t show up on the screen. By turning up the brightness on a good monitor, these four to six retrace lines can be seen slanting diagonally across the picture. PROTECTION CIRCUIT — To protect the high voitage section against voltages that are too high coming from the power supply which could cause X-rays to be emitted from the “flyback”, a circuit senses the higher power supply voltage and turns off the horizontal oscillator. Since the horizontal! oscillator doesn’t work, the horizontal output transistor has nothing to feed the “flyback” which in turn has nothing to feed the picture tube. The monitor wili be silent, have no picture, and will appear to be off. But don’t be fooled. There is still that excessive amount of voltage coming from the power supply. To find out, check at pin two of Wells Gardner's C501 and emitter of X04 for the Electrohome monitor. Check the 95 voit test point (located near the “flyback”) for the Zenith monitor. The Wells Gardner monitor doesn't use this circuit, but an open in the horizontal section could cause the monitor to appear off, yet still have power supply voltage flying around. Here are the voltages you should receive: Wells Gardner = 130VDC Electrohome = 120VDC Zenith = 95VDC The best place to measure this voltage on an Electrohome monitor is at a pin marked B1 on the chassis. This is because a 13 inch color Electrohome-monitor, The G07-FBO or GO7-902, has an integrated circuit and very little else in the power supply. Still, there should be 120VDC at B1.
6-8 THE PICTURE TUBE (OR CRT) —
ATTENTION! For information on picture tube replacement types, go to the last section, “PICTURE TUBE INTERCHANGEABILITY”.
The picture tube or CRT is an output device. In other words, the end result of the circuit's work is displayed by this part. Actually, the output of other circuits is in the neck of the picture tube. First, there is the heater. The heater boils off electrons from the cathodes so that they (the electrons) shoot up to the screen to excite the phosphors so that the three phosphors emit three colors of light. The cathodes are next, and again they emit electrons to turn on the tube phosphors, making it glow. A defective cathode may cause the particular color it handles to be missing. Next come the grids. The first grid is grounded. The following grid is the screen grid which receives about 300VDC depending on the brightness setting. The next grid closest to the picture tube screen is the focus grid which gets about one fifth the amount of voltage that is applied to the picture tube anode. After jetting from the cathode through all these grids, the electrons speed through a mask, a sheet of material with tiny holes, and then excite the tiny dots of phosphor in the inside surface of the picture tube screen. The green electron gun (or cathode and circuitry) spits out electrons which head for the green phosphors only. The same goes for the red and blue guns. The way the phosphor light blends determines the color seen. Should these electron beams become too intense, they may burn the phosphor. With the monitor off, this can be seen as a dark permanent image of the video information on the tube screen.
Differences Between Monitors
The easiest way to identify the brand of monitor you are working with is to find the manufacturer's name or mode! number printed on thechassis or chassis base. But what if the monitor was in a Texas dust storm or buried in volcanic ash and this information is no longer there? Fear noti Each monitor has its own peculiarities and the following should help to identify them: The ELECTROHOME G07-904 (19”) and G07-902 (13") have their horizontal and vertical processing IC hidden under a silver can. A shiny metal top behind the “VERTICAL HEIGHT” and “HORIZONTAL FRE- QUENCY” control prove this is an Electrohome monitor.
The WELLS GARDNER K4906 (19”) and K4806 (13") have their horizontal and vertical processing IC out in the open directly behind the “VERTICAL HOLD” control. The ZENITH CO19MXRFO6 (19") monitor has its horizontal and vertical processing IC way in back by the picture tube. The monitor also has.large white. cables going from the main board to the neck board. K4906 (ist TYPE) — This monitor's identifying tags have BLACK ink printed on a white background. There is NO Vertical Damping Control. (This Control would be next to the Vertical Hold Control but this area is jumpered with a small wire instead. K4906 (2nd TYPE) — This monitor's identifying tags have RED ink printed on a white background. There IS a Vertical Damping Control next to the Vertical Hold Control. The Damping Control provides a few more tines on the top of the monitor screen (monitor viewed as a normal T.V. would be) for any video game that may need these lines to fit the picture on the screen. Moving the Control may distort the top part of your picture (or the side, depending onthe game and how the monitor is mounted) so go ahead and move it if you are having this type of problem. To accommodate this new feature, there are a few circuit changes. ONE MAJOR DIFFERENCE BETWEEN THESE TWO VERSIONS OF THE K4906 IS THE YOKE. They look the same but notice the part numbers: K4906 WITHOUT the Damper Control: 2021111201 K4906 WITH the Damper Control: 2021111258 Since the companies like to change part numbers at the drop of a hat, the best thing to do is to request whatever part number is written on your yoke. If you should get the wrong yoke, the results will be: Picture distortion. Excessive brightness.
Too much or too little vertical picture size.
CONTROLS YOU MAY NOT TOUCH Basically, on the Electrohome monitor, you can move any control you want EXCEPT for the B1 control. This sets the power supply voltage (ideally at 120 VDC) and is located right behind VERTICAL HOLD. The 13” Electrohome DOES NOT have this control. It may also be wise not to move the VERTICAL LIN- EARITY since this distorts the picture and is hard to reset perfectly. If you do move it, turn on the Cross Hatch Test Pattern of your game and try to get the squares to the point where they are equal in size by readjusting this Linearity Control. On the Wells Gardner monitor, brightness is adjusted by the “BLACK LEVEL” Control which is right next to the Horizontal Frequency Control. Under the Focus Control is the “SCREEN” Control which youDO NOT touch. Yes, this control does adjust the brightness, but it is used to set the CRT bias and is adjusted at the factory. When Wells Gardner sets it, they mark.the position with a black mark on the knob. If you move it, be sure to realign the mark and THEN set the BLACK LEVEL Control to the brightness you desire. So, other than the SCREEN control, you may adjust any of the controls. The Zenith monitor has a 95 volt adjustment control. It is green and located behind the jack labeled 3D3. To discourage you from moving it, Zenith has placed a little glue on top of this control.
Parts Interchangeability
Some parts can be interchanged on ail of the monitors. Here are the rules:
- You CAN swap any resistor between monitors that has the same resistance, wattage rating, and _ tolerance.
- You CAN swap any capacitor between monitors that has the same capacitance and voltage rating.
- You CAN swap many of the parts between the 19" and the 13” versions of each manufacturer's monitor. BUT, be certain to compare the manufacturers’ part numbers to be positive the parts you want to interchange are identical. BE SURE you have read the section DIFFERENCES BE- TWEEN MONITORS which was covered earlier.
- You MAY BE ABLE to swap picture tubes between monitors. In the past you could swap any picture tube, but due to rampant engineering changes and new monitor models being introduced, you would need a computer to keep track of what could be swapped. For more information on this subject, go to “PICTURE TUBE INTERCHANGEABILITY”.
- You CANNOT change any part that is a safety
- part, one that is shaded in gray on the schematic; it MUST be IDENTICAL to the original. To do otherwise IS DANGEROUS. For instance, the 13 inch Electrohome (G07-902) monitor “flyback” looks identical to the 19 inch Electrohome (G07- 904) monitor “flyback”. In fact, there is even a 19 inch Electrohome (G07-905) monitor (which is an obsolete model) with a similar looking “flyback”. NONE OF THESE ARE INTER- CHANGEABLE!
- You CAN change any of the parts between the G07-904 and G07-907. They're essentially the same monitor except that the G0O7-907 has a vertically mounted picture tube.
6-9
\f there is any doubt about what parts can be swapped between each manufacturer's 19 inch and 13 inch models, compare the manufacturer's part number between each one. If they match up, they are the same part.
Picture Tube Interchangeability
13" MONITORS There are currently two 13” monitors being used: the Wells Gardner K4806 and the Electrohome G07-902. The picture tubes used are NOT interchangeable. The pins on the neck of the CRT will not fit in the socket should you use the wrong CRT.
Here is a chart for all the 13” color monitors Bally Midway uses. ELECTROHOME WELLS GARDNER K4806
19” MONITORS Here it gets a little tricky. All of the picture tubes will fit no matter which is used. But if you use the wrong one, you will have problems with purity and/er dynamic convergence. Purity trouble means that the color won't be true. If you turn up the color control for one color, instead of seeing that solid color it willshow blotches or blobs of other colors on the screen.
Trouble with dynamic convergence means that there will be color fringing around Solid lines at the edges of the screen. The only way to ensure that you avoid these problems is to get the right picture tube or the right substitute. Here is a list of the 19” monitors and the CORRECT CRT numbers. ALL ELECTROHOME G07-904 — 19VMNP22 RCA 19VMJP22 RAULAND 510UJB22 HITACHI WELLS GARDNER K4906 — 19VLTP22 RCA 19VMLP22 ZENITH JSVMKP22 PHILLIPS
ZENITH CD19MXRFO6 — 1OVMLP22 ZENITH JOVLTP22 RCA 19VMKP22 PHILLIPS G07-902 ~ 370ESB22
- 370KSB22 The factory recommended CRT type could changein the future for one reason or another, but the listed picture tubes will work. As a matter of fact, you can call another picture tube company to see if they have a replacement number to recommend. ..but caveat emptor — let the buyer beware.
Monitor
Power Supply Voltage and Symbols
Symbol | Voltage Operating Circuit | 7 ]
| ® | | | 15V_ | Vert. Osc. | i |
| | | Sync | | | |
| | | Blanking | | | |
| | | CRT Cutoff | | |
e 130V | Horiz. Osc |
| | | Horz. Drive | | |
| Horz, Output | | | | Vert. Output wy T i @ | 175V I Video Output
AVIDIV 200uSECIDIV
‘TP-31 DC COUPLED BOTTOM LINE =0 VOC
2VIDIV 200MSECIDIV
LC, 301, PIN 3
1VIDIV SMSECIDIV
TP.82
20VIDIV SMSECIDIV
LC. 301, PIN 13,
AVDIV 200uSECIDIV 9351 COLLECTOR
2OVIDIV 10uSECIDIV
402-3
SVIDIV 20uSECIDIV
F
1VIDIV 20u SECIDIV
‘TP-31, AC COUPLED
1VIDIV 200uSECIDIV
NEGATIVE SIDE OF €303
2VIDIV SMSECIDIV P81
8 ease omens
O.5IDIV SMSECIDIV
O.5/DIV 20u SECIDIV
LC. 301, PIN 15
2VIDIV 10uSECIDIV
1VDIV 2MSECIDIV 19” COLOR MONITOR SCHEMATIC DIAGRAM
MODELS 19K4901, 19K4906, 19K4951, 19K4956
SERVICE TECHNICIAN WARNING
X-RAY RADIATION PRECAUTION:
THIS PRODUCT CONTAINS CRITICAL ELECTRICAL AND MECHANICAL PARTS ESSENTIAL FOR X-RAY RADIATION PROTECTION FOR REPLACEMENT PURPOSES, USE ONLY TYPE PARTS SHOWN IN THE PAI
hace sync amp vese Hose °°
Hatia23,
cso8 iy | 2 Se8ea00 at so: { 867g
DEGAUSEING COIL
9.40) 9.40: reo'Sur sree Bur 2SCZ06E. 8/8 25C20081.8/ GOK 25C2060L.8/.80K| 28CIBIBBVC/CVC 2SCIBISEVELVC 2SCISI4BVC/CVC
cab) ier é ari? OSCILLOSCOPE WAVEFORM PATTERN The waveforms shown are as observed on the wide band oscilloscope with the monitor turned to a reasonably strong signal and a normal picture. The voltages shown on each waveform are the approximate peak amplitudes. If the waveforms are observed on the oscilloscope with @ poor high frequency response, the corner of the pulses will tend to be more rounded than those shown and the amplitude of any high frequency pulse will tend to be less.
bP bur
f20 229 e FEB oa3 25C945 —
[SYNC amp lescieisy/o
nar? cis BR) 80 180 (780 270 10K Fay PCH ‘eee (pave) FF) [G.CUTOFF
ie
| case | Tee | "ee | _o3se |
1] Stn aot HOR OUT
| 381 | T | 208 |
saxnses) ,SORORIVE =] yee 2808968 ie 2sc24e2% ” rs] 2sczsione
|© t 2368
Piles an in en
Tes ge 263 TEE T3883 ~ ase:
isea78 a) Sek
Yende va)
re, (HOR-CENTERING| er sp goome HV.UNIT 16008/800v
K49010, K4906D, K4951D 5833 K4956B
REPLACEMENT PARTS LIST MAIN BOARD (CONT.,)
| This monitor contains circuits and components included specifically | Ret. No. | Part No. | Description | Ret. No. | Part No. | Description |
for safety purposes.
| For continued protection no changes should be made to the original | CAPACITORS (CONT.) | SEMICONDUCTORS (CONT) | , | |||||
| on parts list should be replaced with exact factory replacement parts. | 202X7050-282 | 1800 pF, S00V Ceraric | 208 | 200x3181-523 | Transistor (NPN) 28C1815GR | |||
| The use of substitute parts may create a shock, fire, radiation or other | 4 0503 | 202X7810-214 | 2200 pF, 125V Ceramic | 209 | 200X3181-523 | Transistor (NPN) 28C1851GR | ||
| hazard. Service should be performed by qualified personnel only. | 0504 | aoaxrei02 4 | 2200 BF 125V Coramlc | Geto | peeled | Transistor NPN seciesian | ||
| C505, | 3X02% | 560 | uF, | lectrolytic | -f | ransistor | ||
| 506 | 209X0040-034 | 22 uF, 160V Electrolytic | 302 | 200X3207-306 | Transistor (NPN) 28C2073LBGL2 | |||
| cs07 | 203X0041.057 | 47 uF, 160V Electrolytic | 9303 | 200X3207-308 | Transistor (NPN) 25C2073LBGL2 | |||
| MAIN BOARD | 701 | 203x0019-092 | 1000 uF, 25V Electrolytic | 351 | 200X3248-217 | Transistor (NPN) 2SC2482BK | ||
| 702 | 203X0634-061 | 10 uF, 100V Electrolytic | 0352 | 200X4589-802 | Transistor (NPN) 2SD898B | |||
| C703 | 202X7050-248 | 4000 pF, 500V Ceramic | ag ot | 200%2500-039 | IC HAL 1428 | |||
| Ret. No. | Part No. | Description | Raf. No. | Part No. | Description | 1C501 | 200X2600-1: | IC STR381 |
- SEMICONDUCTORS
| 203 | 201X2010-159 | Diode, 1$2076-27 | |||||||||||
| RESISTORS | RESISTORS (CONT.) | 0204 | 201X2010-159 | Diode, 1$2076-27 | ast | Line) cede ERS & Colts | |||||||
| R201 | 203x6500-645 | 1K Ohm, 5%, 1/4W Carbon | R369 | 203x5602-329 | 680K Ohm, 5%, 1/2W Comp. | ooos | aoe | Bree: lesuenen | (382 | 201x8000.083 | Coil, Horlz. Size | ||
| R202 | 203X6500-523 | 30 Ohm, 5%, 1/4W Carbon | R370 | 203X8501-002 | 33K Ohm, 5%, 1/4W Carbon | pe | ppoatnace | Dieser earest | or | 11X0004-007 | Coil’ Adg, | ||
| R203 | 203X6500-405, | 100 Ohm, 5%, 1/4W Carbon | R371 | 203X9014-584 | 1K Ohm, 5%, 1W Metal Oxide | peor | poor a | piode, Is207e-27 | 7354 | 202X1300-080 | Transformer, Hor. Drive | ||
| R204 | 203X6700-327 | 100 Ohm, 5%, 1/2W Carbon | R372 | 203X9101-119 | 12K Ohm, 5%, 1W Metal Oxide | £ | node. | ‘ | Ak 1352 | 200X9720-301 | HV-Unit M14 | ||
| R205 | 203X6700-421 | 270 Ohm, 5%, 1/2W Carbon | R375, | 203X6700-763 | 6.8K Ohm, 5%, 1/2W Carbon | 0209 | 201X2010-159 | Diode, 1$2076-27 | |||||
| R206 | 203X6500-540 | 390 Ohm, 5%, 1/4W Carbon | R376 | 203X9104-404 | 270 Ohm, 5%, 2W Metal Oxide | Beer | peas | aoe 'ss81 | 7 | MISCELLANEOUS | |||
| R207 | 340X2201-934 | 200 Ohm, 5%, 1/4W Carbon | R377 | 203X6500-447 | 150 Ohm, 5%, 1/4W Carbon | 302 | anne | Hoge, lezo7e2 | AFSo1 | ooaxri20.078 | Filte, 4.e, | 225% | |
| R208 | 203X6500-540 | 390 Ohm, 5%, 1/4W Carbon | R378 | 203X6500-886 | 10K Ohm, 5%, 1/4W Carbon | 0303 | 1X2010-158 | Diode, tad | vee | peavenneieae | Feces Wiese tees | ||
| R209 | 340X2201-934 | 200 Ohm, 5%, 1/4W Carbon | R379 | 203X6500-886 | 10K Ohm, 5%, 1/4W Carbon | 0304 | Ete | Diode, RH-I | ee | ous | pee pn ie | ||
| R210 | 203X6500-540 | 390 Ohm, §%, 1/4W €arbon | 380 | 203X8500-865 | 8.2K Ohm, 5%, 1/4W Carbon | 0305 | 201K2120 | Diode, RH-IV | en | sopeeto see | Plug, PW SP) | ||
| R211 | 340X2201-934 | 200 Ohm, 5%, 1/4W Carbon | R381 | 203X6500-724 | 2.2K Ohm, 5%, 1W Metal Oxide | eee | go | 10-159 | Diode, 1$2076-27 | Can | Epis cetettd | Bae Rape | |
| Ra14 | 203X6500-645 | 4K Ohm. 5%, 1/4W Carbon | R383 | 203X9014-387 | 150 Ohm, 5%, 1W Metal Oxide | rie | eee | Diode, Ld | Ll | soaxgano | 298 | Plu cwoae | |
| R215 | 203X6501-126 | 100K Ohm, 5%, 1/4W Carbon | R502 | 203X6500-886 | 10K Ohm, 5%, 1/4W Carbon | 4 502 | a | 12028 | Diode, FM 1 | a | coueens aoe | mae ae | |
| R216 | 203X6500-645 | 1K Ohm, 5%, 1/4W Carbon | R503 | 204X1700-535, | 150 Ohm, 5%, 15W Metal Oxide | ry 0503 | 1X3120-2 | Diode, | RM-1AV | THe01 | poixei0tt2 | ba i lator | |
| R217 | 203X6500-405 | 100 Ohm, 5%, 1/4W Carbon | R504 | 203X9014.267 | 47 Ohm, 5%, 1W Metal Oxide | 0504 | 201X3120-216 | Diode, RM-1AV | lermis' | ||||
| R218 | 203X6500-645 | 1K Ohm, 5%, 1/4W Carbon | R505 | 203X6501-209 | 2.2K Ohm, 5%, 1/4W Carbon | ‘D505 | 201X3120-216 | Diode, RM-1AV | |||||
| R219 | 203X6501-126 | 400K Ohm, 5%, 1/4W Carbon | R506 | 209X9104-105, | 15 Ohm, 5%, 2W Metal Oxide | 506 | pean | bese pray | FINAL ASSEMBLY PARTS | ||||
| R220 | 203X6500-645 | 1k Ohm, 5%, 1/4W Carbon | R507 | 203X5602-185 | 330K Ohm, 5%, 1/2W Comp. | o701 | 201X2130-234 | lode, i Mv | ‘Ask 98X0138-506 | TOVLTP22 Pix Tube | |||
| R221 | 203X6500-405 | 100 Ohm, 5%, 1/4W Carbon | A*REO1 | 204X 1625-058 | 3.3 Ohm, 5%, 10W WW | D702 | cmieieiees | Diode, | RH- | pone | aay | Apt ee | bk |
| R222 | 203X6500-762 | 3.3 Ohm, 5%, 1/4W Carbon | R701 | 203X9105-141 | 2.2 Ohm, 5%, 2W Metal Oxide | Q201 | 200X3181-523 | Transistor (NPN) 2SC1815GR | se ouexriieon | ts orale ur ly Assembly | |||
| R224 | 203X6500-169 | 10 Ohm, 5%, 1/4W Carbon | R702 | 203X6206-441 | 2.2 Ohm, 5%, 1/2W Carbon | Q202 | 200X3181-523 | Transistor (NPN) 25C1815GR | 4 | 301.258 | ars eke | ||
| R225 | 203X6500-169 | 10 Ohm, 5%, 1/4W Carbon | R201 | 204X2070-072 | 2K Ohm-B Semi-Fixed | Q203 | 200X4056-260 | Transistor (PNP) 2SA562-Y-TM | 204X9301~ | CRT | Socket | | | |
| R226 | 203X6500-169 | 40 Ohm, 5%. 1/4W Carbon | R301 | 204X2070-084 | 5K Ohm-B Semi-Fixed | Q204 | 200X4056-260 | Transistor (PNP) 2SA562-Y-TM | 291X5004-262 | Automatic Degaussing Coil Unit | |||
| F227 | 203X6501.044 | 47K Ohm, 5%, 1/4W Carbon | VR303 | 204X2070-055 | 500 Ohm-B Semi-Fixed | 205 | 200X4056-260 | Transistor (PNP) 2SA562-V-TM | |||||
| R228 | 203X6500-645 | 1K Ohm, 5%, 1/4W Carbon | VR351 | 204X2070-072 | 2k Onm-B Semi-Fixed | ||||||||
| R229 | 203X6700-421 | 270 Ohm. 5%, 1/2W Carbon | VR352 | 204x2070-072 | > | 2K Ohm-B Semi-Fixed | |||||||
| R230 | 203X6500-863, | 8.2K Ohm, 5%. 1/2W Comp. | |||||||||||
| R231 | 203X6500-863 | 82K Ohm, 5%, 112W Comp. | |||||||||||
| R232 | 203X6500-863 | 8.2K Ohm, 5%, 1/2W Comp. | |||||||||||
| R233, | 203X6500-468 | 180 Ohm, 5%, 1/4W Carbon | |||||||||||
| R234 | 340X2820-934 | 82 Ohm, 5%, 1/4W Carbon | CAPACITORS | KB | |||||||||
| R235 | 340X2820.934 | 82 Ohm, 5%, 1/4W Carbon | 201 | 203x0014-088 | 1000 uF, 16V, Electrolytic | NECK | BOARD | ||||||
| 238 | sanxzgz0 04 | 82 Ohm, 8%, 1M4W Carbon | C202 | 202x7200-084 | 330 pF, 500V, Ceramic | esis | |||||||
| R301 | 203X500-508 | 270 Ohm.5%, 1/4W Carbon | 6203 | 202X7200-043 | 220 pF, S00V, Ceramic | RESISTORS | CAPACITORS | ||||||
| R302 | 203X6500-863 | 8.2K Ohm, 5%, 1/4W Carbon | C204 | 202X7200-043 | 220 pF, 500V, Ceramic | ||||||||
| 303 | 203X6500-863 | 8.2K Ohm, 5%, 14W Carbon | C205 | 203X0014.078 | 470 UF, 16V, Electrolytic | R401 | 203x6000-729 | 220 Ohm, 5% 1/AW Carbon | c401 | 202X7050-269 | 1200 pF, 500V Ceramic | ||
| R304 | 203X6500-724 | 2.2K Ohm, 5%, 1/4W Carbon | C208 | 203X1810-149 | 0.1 uF, 125V Mylar | R402 | 203X6500-540 | 390 Ohm, 5% 1/4W Carbon | 402 | 202X7050-248 | 1000 pF, 500V Ceramic | ||
| R305 | 203X6500-842 | 6.8K Ohm, 5%, 1/4W Carbon | 207 | 349X2232-109 | 022 uF, 100V Mylar | R403 | 203X6000-661 | 820 Ohm, 5% 1/4W Carbon | 403 | 202X7050-248 | 1000 pF, 500V Ceramic | ||
| R306 | 203x6003-201 | 7.5K Ohm: 2%. 1/4W Carbon | 301 | 203X0014065 | 390 uF. SOV Electrolytic | R404 | 203x6000-729 | 220 Ohm, 5% 1/4W Carbon | C404 | 202X7050-282 | 1500 pF, 1.5KV Ceramic | ||
| R307 | 203X6500-825 | 5.8K Ohm, 5%, 1/4W Carbon | C302 | 203x 1600-563. | 0.033 UF, 50V Mylar | R405 | 203X6500-540, | 390 Ohm, 5% 1/4W Carbon | 405 | 202X7050-483, | 0.01 uF, 500V Ceramic | ||
| R309 | 203X6500-965 | 22K Ohm, 5%, t/4W Carbon | 303 | 203X0629-037 | 3.3 UF, 50V Electrolytic | R408 | 203%6000-661 | 820 Ohm, 5% 1/4W Carbon | |||||
| R310 | 203x6800-988 | 39K Ohm, 5%, 1/4W Carbon | C304 | 203X 1800-366 | 0.068 pF, S0V Mylar | R407 | 203X6000-729 | 470 Ohm, 5% 1/4W Carbon | SEMICONDUCTORS | ||||
| R311 | 203X6500-762 | 3.3K Ohm, 5%, 1/4W Garbon | C306 | 203X0412-.012 | 2.2 uF, 16V Tantal | R408 | 203X6000-998 | 270 Ohm, 6% 14W Carbon | |||||
| R312 | 203X9014-741 | 4.7K Ohm, 5%, 1/4W Carbon | 307 | 203X 1600-634 | 0.033 uF, SOV Mylar | R409 | 203X6000-661 | 820 Ohm, 5% 1/4W Carbon | 401 | 200X3206-800 | Transistor (NPN) 2SC2068LB | ||
| R313 | 204X 1450-537 | 1K Ohm, 5%, SW Carbon | 308 | 203x0025-174 | 3.3 uF, 50V Electrolytic | Reto | 205KO 104-824 | 15K Ohm, 5% 2W M0. Forming | Qao2 | 200x3206-800 | Transistor (NPN) 2SC2068L8 | ||
| R314 | 203X6500-481 | 220 Ohm, 5%, 1/4W Carbon | 309 | 203X 1207-100 | 0.068 uF, 100V PP | Ratt | 203x9104-824 | 15K Ohm, 5% 2W M.O. Forming | 403 | 200X3206-800 | Transistor (NPN) 2SC2068LB | ||
| F315 | 203X6500-169 | 40 Ohm, 5%, 1/4W Carbon | C310 | 03X0629.061 | 10 uF, 100V Electrolytic | R412 | 203X9104-824 | 15K Ohm, 5% 2W M.O. Forming | |||||
| R316 | 203X6500-762 | 3.3K Ohm, 5%, 1/4W Carbon | C311 | 203X004 1-025 | 10 uF, 160V Electrolytic | Ra13 | 203X6000-998 | 2.7K Ohm, 5% 12W Comp. | |||||
| R317 | 203X6700-107 | 12 Ohm, 5%, 1/2W Carbon | C312 | 202X7050-248 | 1000 pF, 500V Ceramic | Rata | 203X6000-998 | 2.7K Ohm, 5% 12W Comp. | MISCELLANEOUS | ||||
| R318 | 203X6500-540 | 390 Ohm, 5%, 1/4W Carbon | C313 | 203X0040-052 | 47 uF, 180V Electrolytic | R415 | 203X6000-998 | 2.7K Ohm, ore ey Comp. | J401 | 206X5009-296 | RECEP W Wire 4P-E | ||
| R319 | 203X6500645, | 1K Ohm, 5%, 1/4W Carbon | C314 | 203X1201-265 | 0.033 uF, 200V PP | R416 | 203X9105-154 | 2.2 Ohm, 5% 2W Metal Oxide | pave | oaxeeooa84 | Bug, PWB SPA | ||
| R320 | 203X6501-002 | 33K Ohm, 5%, 1/4W Carbon | 6315 | 203X0629-023 | 1 uF, 50V Electrolytic | R419 | 203X6500-741 | 2.7 Ohm, 5% 14W Carbon | 403 | 204x9600.981 | Plug, Pin 1P-D | ||
| R321 | 203X6501-224 | 270K Ohm, 5%, 1/2W Carbon | C351 | 203x0629-023, | 1 uF, 50V Electrolytic | R420 | 203X6500-741 | 2.7K Ohm, 8%. U4WiCarbon | P701 | 204X9601-020 | Plug, PWB 4P-€ | ||
| A322 | 303x6500-886 | 40K Ohm, 5%, 1/4W Carbon | 352 | 203x0819.045 | 47 uF, 25V Electrolytic | R421 | 203x6500-741 | 2.7K Ohm, 5% 1/4W Carbon | |||||
| R351 | 203X6500-886 | 10K Ohm, 5%, 1/4W Carbon | C353 | 203X 1190-015 | 0.0082 pF, S0V Mylar-PP | R401 | 204X2116-014 | 500 Ohm, -B Semi-Fixed | |||||
| R352 | 203X6500-785 | 3.9K Ohm, 5%, 1/4W Carbon | C354 | 203X0619-045 | 47 uF, 25V Electrolytic | Migs | 204X2115-014 | 500 Ohm, -8 Semi-Fixed | |||||
| R353, | 203X6501.086 | 88K Ohm, 5%, 1/4W Carbon | C355 | 203X 1600-366 | 0.0068 pF, 50V Mylar | VR403 | 204X2115-006 | 5K Ohm, -B Semi-Fixed | |||||
| R354 | 203X6500-762 | 3.3K Ohm, 5%, 1/4W Carbon | C356 | 202X7050-483 | 0.01 uF, S00V Ceramic | VR404 | 204X2115-006 | 5K Ohm. -B Semi-Fixed | |||||
| R355 | 203X9205-143, | 6.8K Ohm, 5%, 3W Metal Oxide | C359 | 202X8065:608 | 100 pF. 500V¥ Ceramic | R405 | 204X2115-006 | 5K Ohm, -B Semi-Fixed | |||||
| R358 | 203X5601-878 | 56K Ohm, 5%, 1/2W Carbon | 360 | 202X7050-368 | 0.0033 pF, 500V Ceramic | ||||||||
| R360 | 203X6500-561 | 470 Ohm. 5%, 1/4W Carbon | C261 | 202X7050-483 | 0.01 uF, 500V Ceramic | ||||||||
| R361 | 203X6500-886 | 10K Ohm, 5%, 1/4W Carbon | C362 | 202X7203-032 | 0.01 uF, 50V Ceramic | ||||||||
| R362 | 203x9014-645 | 1.8 Ohm, 5%, 1W Metal Oxide | D*C363 | 203x 1270-911 | 8700 pF, | 15 KV PP | |||||||
| R363 | 204X1527-751 | 3.9K Ohm, 5%, 7W Metal Oxide | C365 | 203X1201-265 | 0.33 uF, 200V PP | ||||||||
| R364 | 203X6500-246 | 22 Ohm, 5%, 1/4W Carbon | C366 | 203X0019-026 | 22 uF, 25V Electrolytic | ||||||||
| R365 | 203x8501-002 | 33K Ohm, 5%, 1/4W Carbon | 367 | 202X8065-162 | 6 pF, 500V Ceramic | ||||||||
| R367 | 203X6500-886 | 10K Ohm, 5%. 1/4W Carbon | C368 | 202X7203-032 | 0.01 UF, 50V Ceramic | ||||||||
| R368 | 203X5602-185, | 330K Ohm, 5%, 1/2W Comp. | 372 | 203X1207-125, | 0.1 uF. 100V PP |
6-13
6-14 Beroea, asciasa POWER REGULATOR rps, fe] X91 POWER DRIVE 25¢ 2688 X 902 ERROR AMP 25C1890 BLUE a"1U4 RED X101.X103 ond X15 VIDEO AMP. 28C454C X102.X704 ond _Xi96 VIDEO AMP. 2586736
i:
+
J] xs0s wea uimiter 250673 [x301,x302,%308,x308 ISyNC AMP l2scas4c or pciees
pe [304 BLANKING 28C484C or dscices
he ROENOS Ree Voge cuTruT 2SC26II or BScisia
1 ie
1/Sho
aoe ONT Fate asf tet 34! si08 rim nth
By
bie ares, te a
X701 X-RAY PROTECTOR 28C454¢ or 28C1685
ACIZOV 60Hz/50H2 10% 301 H.0RIV OUT Beiso7 WG, escesrv 390898 er 2SC26il or B8C26iOaK 280869 or 250820 { i ' { ut cz) fem
00-4147-04 G07-CBO Schematic Notes Unless otherwise specified Resistance: (.) (K->KQ, M-~MQ), 1/4 (W) carbon resistor Capacitance: 1 or higher—> (pF), less than 1-~ (yF) working voitage -> 50 (V) ceramic capacitor Inductance: (vH) Electrolytic Cap: Capacitance Value (y F)/working voltage (V), NP — non-polar (or bipolar) electrolytic cap. Refer to the parts list for additional component information. 2 indicates test point connection ah indicates chassis ground unless otherwise specified Hz _ indicates cycles per second For safety purposes (and continuing reliability) a replace al} components marked with safety syrnbol with identical type.
Parts identification on circuit boards: e.g. SU1126A (R107 = R1107) $U3030A (R113 = R3113)
REPLACEMENT PARTS LIST~ELECTROHOME 19" MONITOR
Components identified by the A symbo! in the PARTS LIST and on the Schematic have special characteristics
DO NOT degrade the safety of the sei through improper servicing.
Abbreviations for Resistors and Capacitors
Resistor
| CR | : | Carbon Resistor |
Comp. R Composition Resistor
| OMR | : | Oxide Metal Film Resistor |
| VR | : | Variable Resistor |
MFR Metal Film Resistor CMF R Coating Metal Film Resistor
| UNF R | : | Nonflammable Resistor |
| FR | : | Fusible Resistor |
MM Cap. PP Cap. MPP Cap. PS Cap. Tan. Cap. Capacitor
C Cap. M Cap. E Cap. BP E Cap. Ceramic Capacitor Mylar Capacitor Electroiytic Capacitor Bi-Polar (or Non-Polar) Electrolytic Capacitor
Polystyrol Capacitor Tantal Capacitor Metalized Mylar Capacitor Polypropylene Capacitor Metalized PP Capacitor
Use of substitute replacement parts which do not have the same safety characteristics as specified, may create shock, fire or other hazards. For maximum reliability and performance. all parts should be replaced by those having identica! specifications.
SERVICE REPLACEMENT PARTS LIST
Symbol _ Description Main PC.B. Ass'y CRT Socket PC.B. Assy Purity Shield Ass'y
Outside of the P.C.B. Ass'y Symbol Description Picture Tube 19" a A\Deflection Yoke PC Magnet A AFlyback Transf. aN AHVR ROS UNF Resistor 220.2,25W K co4 C Capacitor 150pF AC1.5KV X01 Si. Transistor x02 Si. Transistor sc Screw #8-% sc Screw % x % Pix Tube Mtg. (4) WA Pyramidal Lock Washer (4) Nut Retainer, Pix Tube Mtg. (4) Clip—P.C.8. Support Standoff Wire Terminal (Gnd. Strap) Terminal Lug (Gnd.) Groundstrap Assy. Grounding Spring Wire Hook (Gnd. Strap) Purity Shield Holddown Ciamp Support Brkt. RH Support Brkt. LH Chassis Base Yoke Wedge (3) Part Number SU-1133A, SU-3032A 07-220083-03
Part Number 17-7198-03
A29951-B A46600-A QRF258K-221 QCZ0101-005 2SD870 2SC1106A 31-610818-06 31-601418-12 33-255-01 33-494-01 33-629-02 33-670-010R-02 34-228-03 34-33-04 34-574-02 35-212-03 35-3053-02 35-2348-01 35-3890-01 35-3890-02 38-449-02 39-1233-01 Purity Shieid Ass’y. Parts List
Symbol Description Degaussing Coil 0911, D912 Rectifier 1 Amp 600V (2) Pin Terminal (2) Pin Terminal Housing Purity Shield (2 pes.) Purity Shield (2 pcs.) co11 Capacitor 100nF 10% 400V R921 Resistor, Wirewound 33.2, 4W Fire Retardant Term. Strip 4 Lug Part Number 21-1007-30
28-22-27 34-708-01 34-709-01 35-3847-01 35-3847-02 48-171544-62 42-113301-03 34-492-09
CRT Socket P.C.B. Ass'y (SU-3032A) Parts List
Resistors Symbol Description
| R3105 | Vv | R | 200 |
| R3106 | v | R | 200 |
| R3113, | v | R | 5K |
| R3114 | Vv | R | 5K |
| R3115 | Vv | R | 5K |
| R3116 | OM | R | 10Ke2W J |
| R3117, | OM | R | 10K22W J |
| R3118 | OM | R | 10K22WJ |
| R3119 | Comp. R | 3.3KQ%W K | |
| R3120 | Comp.R | 3.3KQ%W K | |
| R3121 | Comp.R | 3.3K2%W K |
Capacitors Symbol Description
| C3107 | E | Cap. | 10uF 250V A |
| C3108 | C | Cap. | 1000pF DC1400V P |
Part Number QVZ3234-022 QVZ3234-022 QVZ3234-053 QVZ3234-053 QVZ3234-053 QRGO029J-103 QRGO29J-103 QRGO29J-103 QRZ0039-332 QRZ0039-332 QRZ0039-332
Part Number QEW53EA-106 QCZ9001-102M CRT Sccket P.C.B. Ass'y (SU-3032A) Parts List (Cont.)
Colls Symbo! £3101
Semiconductors Symbol X3101 X3102 X3103
Miscellaneous Symbol A Description Peaking Coii
Description Si, Transistor Si. Transistor Si. Transistor
Description ASCRT Socket
Main PCB Ass’y (SU-1133A) Parts List Resistors Symbol R1406 R1408 R1410 R1414 R1415 R1421 R1422 AFR1401 AXR1503 R1504 R1509 R1512 R1514 R1515 R1522 R1523 R1528 R1534 VR1501 A\R1703 A\R1704 AR1901 R1902 R1903, R1904 R1905 A\qi1908 AR1909 R1910 AFR1901
Capacitors Symbol C1301 1402 C1407 C1411 C1412 C1508 Ac1512 Ac1513 Aci514 C1515 C1520 C1523 C1524 Ac1s31 Ac1532 C1904 C1905 Description VR 2002 VR 2002
| CMF | R | 6821WJ |
| OM | R | 3.3KQ1WJ |
| OM | R | 27KQIWJ |
| OM | R | 12KQ2WJ |
| Vv | Rs | 10KQ |
AF — R 6822WK
| ACMF | R | 11.8KQ%W+1% |
VOR 5KQ
| OM | R | 10KQ2WJ |
| OM | R | 82KQ2WJ |
| OM | R | s82022WJ |
| CMF | R | 8.201WJ |
| CMF | R | 4.701WJ |
| OM | R | 6822WJ |
| OM | R | 39021WS |
ZN OR ZN OR ACMF R 392%W+1% ACMF R 7.68KQ%W+1% AsPosistor
| UNF | R | 227WK |
| CMF | R | 4.723WJ |
| OM | R | 10KQ2WJ |
| OM | R | 18KQ1WJ |
| ACMF | R | 472%W+1% |
VR 2ka
| ACMF | R_ | 2.74KQ%W+1% |
AF = R 2200%WK
Description BPE Cap. 3.3uF 50V A Tan Cap. 2.2uF 16V K E Cap. 4.7uF 6.3VA E Cap. 100uF 160V.A E Cap. 3.3uF 160V A PP Cap. 5600uF SOV J APP Cap. 2000pF DC1500V J APP Cap. 2000pF DC1500V J AXPP_ Cap. 2000pF DC1500V J PP Cap. 0.53uF DC1200V J BPE Cap. 3.3uF 50V A E Cap. 1uF 160V A M_ Cap. 0.1uF 200V K APP Cap. 2000pF DC1500V J APP Cap. 1500pF DC1500V J E Cap. E Cap. 10uF 250VA Part Number QQL043K-101
Part Number 2SC1514VC 2S8C1514VC 28C1514VC
Part Number A76068
Part Number QVZ3230-002 QVZ3230-002 QRX019J-6R8 QRGO19J-332 QRGO19J-272 QRGO26J-123Z QVZ3230-014 QRH024K-680M QRV142F-1182 QVZ3230-053 QRGO26J-103Z QRGO026J-822Z QRG026J-821Z QRX019J-8R2 QRX019J-4R7 QRGO26J-680Z QRGO19J-391 ERZ-C052K471 ERZ-C05ZK271 QRV122F-3902 QRV142F-7681 A75414 QRFO76K-2RO QRX039J-4R7 QRGO26J-103Z QRGO19J-183 QRV122F-470Z QVP5A0B-023E QRV142F-274i QRH124K-221M
Part Number QEN61HA-335Z QEES1CK-225B QEWS51JA-475 QEWS52CA-107 QEWS52CA-335 QFP31HJ-562 QFZ0082-202 QFZ0082-202 QFZ0082-202 QFZ0067-534 QEN61HA-335Z QEW62CA-105Z QFM720K-104M QFZ0082-202 QFZ0082-152 QEY0034-001 QEWS2EA-106 Main PCB Ass'y (SU-1133A) Parts List (Cont.) Colls ‘Symbol 11502 L1503 L1504
Transformers Symbol T1501 T1503
Semiconductors Symbol 1C1501 X1101 X1102 X1103, X1104 X1105 X1106 X1301 x1302 X1303 X1304 X1305 X1401 X1402 X1501 X1901 X1902 D1101 01102 01103 D1301 D1401 D1402 D1503 01504 D1505 D1506 D1507 D1508 Ap1701 A\D1901 AD1902 A\D1903 A\D1904 A\D1905
Miscellaneous Symbol AF1901 AF1902 Description Linarity Coil Width Coil Heater Choke
Description Hor. Drive Transf. Side Pin Transf.
Description Ic Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Diode Si. Diode Si. Diode Si. Diode Si. Diode Zener Diode Si. Diode Si. Diode Zener Diode Si. Diode Si. Diode Si. Diode AZener Diode ASi. Diode ASi. Diode ASi. Diode ASi. Diode AZener Diode
Description Afuse 1.254 ANUL Fuse 3A Part Number A39835, C30380-A C30445-A
Part Number A46022-8M C39050-A
Part Number HA11244 28C1685(R) 2SA673(C) 28C1685(R) 2SA673(C) 28C1685(R) 2SA673(C) 28C1685(R) 28C1685(R) 2SA673(C) 2SC1685(R) 28C1685(R) 28D478 28D478 28C2610BK 28C2686 (K.L.M.) 2SC1890A (E.F) WoeA WO6A WO6A 18Z473H 18Z473H RD10F(C) HF-1 VO9E RD11E(B) Wo6A 18881 18Z473H RD20EV2 181887A 181887A 181887A 181887A RD6.8EV3
Part Number QMF53U1-1R25S QMF66U1-3ROS
6-16 Ico! POWER REGULATOR STR363 SU-1103A MAIN PCB ASSY Md SAKES HE XIO1 XIO3 and KIO’ VIDEO AMP, 28C454C y 8c 1685 2102. x198 ang Xi06 VI0EO_AMA_284673¢
X303 BEAM LIMITER 258673 X304 BLAYKING ascasac TO=Xi03 RGB VIDEO OUTPUT, 28¢2611 or a8cisiav
& SU-3016A | CRT SOCKET pee assy |
| Se
Acizov 6oHe/SoHE 210% byor DEFLECTION YOKE
501 H.ORIVE On OUT 25cis07 KL, 28C237IV 250838 or 28C2ai or 28C26108K 250969 TOI X-RAY PROTECTOR 25CA34C or 25¢ 1665
G07-FBO
00-4147-03 Schematic Notes Unless otherwise specified Resistance: (Q.) (K->KQ, M*MQ), 1/4 (W) carbon resistor Capacitance: 1 or higher—> (pF), less than 1-~ (yF) working voltage» 50 (V) ceramic capacitor Inductance: (v H) Electrolytic Cap: Capacitance Value (y F)/working voltage (V), NP — non-polar (or bipolar) electrolytic cap. Refer to the parts list for additional component information. 2 indicates test point connection oh indicates chassis ground unless otherwise specified Hz _ indicates cycles per second For satety purposes (and continuing reliability) & replace all components marked with safety symbol with identical type.
Parts identification on circuit boards: e.g. SU1126A (R107 = R1107) SU3030A (R113 = R3113)
REPLACEMENT PARTS LIST—-ELECTROHOME 13" MONITOR
Components identified by the A symbol in the PARTS LIST and on the Schematic have special characteristics
DO NOT degrade the safety of the set through improper servicing.
Abbreviations for Resistors and Capacitors
Resistor Capacitor
| CR | : | Carbon Resistor | C Cap. | Ceramic Capacitor |
| Comp. R | Composition Resistor | M Cap. | Mylar Capacitor | |
| OMR | Oxide Metal Film Resistor | E Cap. | Electrolytic Capacitor | |
| VR | Variable Resistor | BPE Cap. | Bi-Polar (or Non-Polar) | |
| MFR | Metal Film Resistor | Electrolytic Capacitor | ||
| CMF R | Coating Metal Film Resistor | MM Cap. | Metalized Mylar Capacitor | |
| UNF R | Nonflammable Resistor | PP Cap. | Polypropylene Capacitor | |
| FR | : | Fusible Resistor | MPP Cap. | Metalized PP Capacitor |
PS Cap. Polystyrol Capacitor Tan. Cap. Tantal Capacitor
Use of substitute replacement parts which do not have the same safety characteristics as specified, may create shock, fire or other hazards. For maximum reliability and performance, all parts should be replaced by those having identical specifications.
SERVICE REPLACEMENT PARTS LIST
Symbol Description Main PC.B. Ass'y CRT Socket P.C.B. Ass'y
Outside of the P.C.B. Ass'y
Symbol Description Avo1 = APicture Tube 13" Apyo1 ADetiection Yoke PC Magnet Wedge AsFlyback Transf. Ari1 AFocus VR AROS UNF Resistor 220:2,25W. K Aco4 AC Capacitor 150pF, A C1.5KV X01 Si. Transistor 1Co1 IC Regulator Lot Degaussing Coil Degaussing Coil Pin Terminal (2) Degaussing Coil Pin Terminal Housing Groundstrap Ass'y Groundstrap Wire Terminat Groundstrap Spring (2) BR Support Bracket RH BR Support Bracket LH sc SCREW 10-% Pix Tube Mtg. (4) WA Pyramidal Lockwasher (4) Clip PC.B. Support (2) Ground Lug CH Chassis Base Part Number SU-1103A SU-3016A,
Part Number 370ESB22(E) C29123-V A76366-A 30006 A19183-A A46606-A QRF258K-221 QCZ0101-005 2SD869 STR383 21-1007-31 34-708-01
34-709-01 34-697-04 34-228-03 35-3560-01 35-3919-01 35-3919-02 31-631018-08 33-255-01 33-629-02 34-33-04 38-452-01 Main P.C.B. Ass'y (SU-1103A) Parts List
Resistors Symbol Description
| R1406 | Vv | R | 2002 |
| R1408 | Vv | -R | 2000 |
| R1410 | CMF | R 6821WJ | |
| R1414 | OM | R | 33Kq1WJ |
| R1415, | OM | R | 27KQIWJ |
| R1421 | OM | R | 12KQ2WJ |
| R1422 | VR | 10K | |
| AFR1401 | AF | R | 6822WK |
| AR1503. | «= ACMF | R= | 11.82%W +1% |
| R1504 | VR | 8KQ | |
| R1509 | OM | R | 10K22WJ |
| R1511 | OM | R | 5.6K22WJ |
| R1514 | OM | R | 68022WJ |
| R1515, | CMF | R | 8.221WJ |
| R1522 | CMF | R | 4.701WJ |
| R1523, | OM | R | 5622WJ |
| R1528 | OM | R | 39021WJ |
| R1534 | ZN | OR | |
| VR1501 | ZN | oR | |
| Ar1703. | = ACMF | R 3aKeKW +1% | |
| AR1704. | ACMF | R | 7.68KQY%W +1% |
AR1901 — APosistor
| R1902 | UNF | R | 227WK |
| R1903 | CMF | R | 5.623WJ |
| R1904 | OM | R | 10Ke2WJ |
| ArFR1901 | AF | R | 2202%W K |
Part Number QVZ3230-022 QVZ3230-022 QRX019N-6R8 QRGO19J-332 QRGO19J-272 QRGO29J-123 QVZ3224-014H QRH024K-680M QRV142F-1182 QVZ3230-053 QRGO028J-103 QRGO029J-562 QRG029J-681 QRX019J-8R2 QRX019J-4R7 ORGO29J-560 ORGO19J-391 ERZ-CO5ZK471 ERZ-CO5DK271 QRV122F-3902 QRV142F-7681 A75414 QRFO76K-2RO QRX039J-5R6 QRGO26J-103Z QRH124K-221M Main P.C.B. Ass'y (SU-1103A) Parts List Capacitors Symbol Description C1402 Tan. Cap. 2.2uF 16V K
| C1411 | E | Cap. 100uF 160VA |
| C1412 | E | Cap. 3.3uF 160V A |
| C1508 | PP | Cap. 5600pF SOV J |
| C1511 | E | Cap. 47uF 160V A |
AC1512 APP Cap. 2000pF DC1500V J Aci513 APP Cap. 2000pF DC1500V J Aci514 = APP Cap. 2500pF DC1500V J C1515 PP_ Cap. 0.53uF DC1200V K C1520 BPE Cap. 1uF 50VA
| C1524 | M_ | Cap. 0.1uF 200V K |
| C1904 | E | Cap. |
| C1905 | E | Cap. 10uF 250VA |
4\C1907 AMM Cap. 0.1uF AC150V Z
Coils Symbol Description L1501 Peaking Coil L1502 Liniarty Coil L1503, Width Coil L1504 Heater Choke L1901 Line Filter
Transformers Symbol Description 71501 Hor. Drive Transf. T1503 Side Pin Transf.
Semiconductors Symbol Description 1C1501 Lc. X1101 Si. Transistor X1102 Si. Transistor X1103 Si. Transistor X1104 Si. Transistor X1105 Si. Transistor 1106 Si. Transistor X1301 Si. Transistor X1302 Si. Transistor X1303 Si. Transistor X1304 Si. Transistor X1305 Si. Transistor X1401 Si. Transistor X1402 Si. Transistor X1501 Si. Transistor X1701 Si. Transistor D1101 Si. Diode D1102 Si. Diode D1103 Si. Diode D1301 Si. Diode D1401 Si. Diode D1402 Zener Diode D1503 Si. Diode D1504 Si. Diode D1505 Zener Diode D1506 Si. Diode D1507 Si. Diode D1508 Si. Diode AD1701 AZener Diode Apdi901_— Si. Diode A\D1902 ASi. Diode A\D1903 ASi. Diode A\D1904 ASi. Diode
Miscellaneous Symbol Description ArFi901 — AFuse 1A AF1902_ — AUL Fuse 3A Part Number QEES1CK-225B QEWS2CA-107 QEWS2CA-335 QFP31HJ-562 QEWS52CA-476S QFZ0082-202 QFZ0082-202 QFZ0082-252 QFZ0067-534 QEN61HA-105Z QFM720K-682M QEY0034-001 QEWS2EA-106 QFZ9008-104
Part Number A75360-6 A39934 C30380-A C30333-A A39475-5
Part Number A46022-BM C39050-A
Part Number HA11244 28C1685(R) 2SA673(C) 2SC1685(R) 2SA673(C) 2SC1685(R) 2SA673(C) 28C1685(R) 2SC1685(R) 2SA673(C) 2SC1685(R) 2SC1685(R) 280478 28D478 2SC2610BK 2SC1685(P-S) WO6A ‘WO6A. WO6A 1$2473H 182473H RD10F{(C) HF-1 VOoE RD11E(B) WO6A 18881 182473H D20EV2 181887A 1$1887A 1S81887A 181887A
Part Number QMF53U1-1ROS QMF66U1-3ROS Resistors Symbol Description R3105 VR 2002 R3106 VR 2002 R3113 VR 5KQ R38114 VR 5KQ R3118 VR 5KQ R3116 OM R 10K22W J R3117 OM R 10K22WJ R3118 OM R 10K22W J R3119 Comp. R 3.3K2%W K R3120 Comp. R 3.3K2%W K R3121 Comp. R 3.3K2%W K
Capacitors Symbol Description C3107 E Cap. 10uF 250V A C3108 C Cap. 1000pF DC1400v P
Coils Symbol Description L3101 Peaking coil
Semiconductors Symbol Description X3101 Si. Transistor X3102 Si. Transistor X3103 Si. Transistor
Miscellaneous Symbol A Description CRT Socket CRT Socket P.C.B. Ass'y (SU-3016A) Parts List
Part Number QVZ3234-022 QVZ3234-022 QVZ3234-053 QVZ3234-053 QVZ3234-053 QRGO29U-103 QRGO29J-103 QRGO29J-103 QRZ0039-332 QRZ0039-332 QRZ0039-332
Part Number QEW52EA-106 QCZ9001-102M
Part Number QQLO43K-101
Part Number 2SC2611 2SC2611 2802611
Part Number A75522
6-17
6-18
| er | 1 | a | — | 77 |
re 1 oO) | oa | \ ___ vert. Low vert | TWIST CABLE | — mgr | | r
| a | se | r | TES | ae | « |
k caer?
ew3276 & Ra279
(cRaz02 I nxa240 bex2208 ‘raaso% Raves Figs
£3) 3H
egs: +e
ET t,, ei A Vs wot tae = ‘ote
Raza 2.28 te 83242
cas | i oS oN
ie
‘2
254 ne |
ad | sacames
coe | oe
| a38s
: 2 MEG
‘GROUND wun se Source i axe Prey rans | ORIVE
cece ees 3298, a |
| Tae | I | vt | Tea208 | Te. | |
| 93204 | ~ DRIVER | as | ad | ‘SWEEP | teen” 53229 | sag |
| 121-83 | axse02 | | | _ | one | |
| deca | oxs202 | ! | _ |
| 26KV
| j | / | < AtGH | r |
i} H VOLTAGE
“LL RES TORS ARF 1/6 aa FILM 9% TOLERANCE ess Stwemwise SMECILC, SAPECICHTORS ARE IN MICROFANADS USLESS (OmiSE SPECIFIED TO \ |? Base | 9-166-03] 983 Bite cx3227
, so cxaze9 re Teen
| rxazo2 |
f-9740-0%
REFERENCE ONLY
SCHEMATIC FOR
SWEEP BOARD | RGB COLOR MONITOR | | ZENITH pee RADIO corP..! 8 , cHicaco. 1. | M05 1-00087-A021
ores: sep win cmmeur eres See super wine USED Hse: Ce ¥ @— PROVISION ON PRINTEE CIRCUIT BOARD.
Ref. No.
C2131 C2152 C3201 CX3202 C3203 CX3204 CX3205 C3206 C3207 C3209 03211 C3212 03213 C3214 C3216 C3217 C3218 C3222 CX3228 CXx3229 C3233 C3244 C3261
CR3202 CR3203 CRX3204 CR3205 CR3206 CR3207
CR3208 CR3209 CR3210 CR3211 QX3202 QX3204 Q3206 QX3207 Q3209 SWEEP BOARD (9-186-03)
| Part No. | Description | Ret. No. | Part No. | Description |
CAPACITORS TRANSFORMERS & COILS
| 22-7508 | 47 MF, 38V, +20% Electrolytic | 13207 | 149-454 | Core, Ferrite Bead |
| 22-7508-01C | 22 MF, 35V, +20% Electrolytic | 13220 | F-13834 | Core & Sleeving Assy. (149-509-01) |
| 22-7410-05 | 10 MF, 100V, +20% Electrolytic | Lx3261 | 20-3976 | Coil Width |
| 22-710-01C | 1 MF, 50V, +50%-10% Electrolytic | Lxg262 | 20-3975 | Coil, Linearity, with 205-271 Hot Melt |
| 22-7711-08C | 47 MF, 63V, +50%—10% Electrolytic | 3205 | 95-3344 | Transformer, Horizontal Driver |
| 22-7773-24A | 0.1 MF, 100V, +5% Polyester | 7x3204 | 95-3581-01 | Transformer, Sweep |
22-7523-01 0.01 MF, 2KV, +20% Disc 22-7708-04C 4.7 MF, 25V, +50%—10% Electrolytic RESISTORS
| 22-5665 | 330 PF, 1000V, +10% Disc | R2105 | 63-9921-94 | 8.2K Ohm, +5% 1/4W Film |
| 22-7242 | 0.0018 MF, 200V, +10% Disc | R2110 | 63-9921-64 | 470K Ohm, +5% 1/4W Film |
| 22-7777-20B | 0.047 MF, 200V, + 10% Polyester | Rott | 63-9919-83 | 3K Ohm. 12% 1/4W Film |
| 22-7234 | 560 PF; 500V, 10% Dise | 2112 | 63-9919-96 | 10K Ohm, +2% 1/4W Film |
| 22-7775-16A | 0.022 MF, 100V, +20% Polyester | RXx3204 | 63-9021-80 | 2.2K Ohm, +5% 1/4W Film |
| 22-7775-10A | 0.0068 MF, 100V, +20% Polyester | RX3206 | 63-7805 | 3.3K Ohm’ +5% 1/2W Carbon |
| eee | 470'EF, 500V.420% Disc: | RX3207 | 63-9921-32 | 22 Ohm, +5% 1/4W Film |
| 22-5684 | 470 PF, SOOV, +20% Disc | RX3208 | 63-10235-80 | 2.2K Ohm, +5% 1/4W Film |
| 22-7774-15C | 0.018 MF, 100V, +10% Polyester | RX3209 | 63-10236-72 | 1K Ohm, 45% 1/4W Film |
| 22-7742-10 | 0.001 MF, SOV, £10% Axial | RX3210 | 63-7805, | 3.3K Ohm, +5% 1/2W Carbon |
| 22-6466 | 530. PF, SKV, 210% Disc | RX3211 | 63-10810-07 | 3K Ohm, +1% 1/2W Film |
| 22-7672-07 | (0.013 MF, 1 6KV, +5% Polypropylene | RX3214 | 63-10233-81 | 2.4K Ohm, +2% 1/4W Film |
| 22-7728 | 0.68 MF, 200V, +10% Polyester | RX3216 | 63-10810-06 | £196 1/2W Film |
| 22-7566-24 | 0.1 MF, 250V, +10% Polyester | RX3217 | 63-7760 | re |
| 22-7683-01 | 0.68 MF, 200V, +5% Polypropylene | RX3215 | 62-10235-98 | |
| RX3218 | 63-10235-82 | 25% 1/4W Film | ||
| SEMICONDUCTORS | RX3219 | 63-10235-88 | 5% 1/4W Film | |
| 103-142-01 | Diode, Low Voltage | 3224 | 63-9946-88 | 5% 1/2W Film |
| 103-330A | Diode, Low Voltage | 3225 | 63-10836-68 | 680 Ohm, +5% 2W Wire Wound |
| 103-308A | Diode, Zener | F3226 | 63-10235-74 | 1.2K Ohm, +5% 1/4W Film |
| 103-305 | Diode, Damper | 3227 | 63-10235-80 | 2.2K Ohm, +5% 1/4W Film |
| 103-2844 | Diode, Low Voltage | RX3295 | 63-10810-06 | 1.2K Ohm, +1% 1/2W Film |
| 103-295-01A | Diode, Low Voltage | RX3240 | §3-10657-04 | 10 Meg Ohm, +20% 1/2W Carbon |
| (used with 149-454) | 3242 | 63-10243-80 | 2.2K Ohm, +5% 1/2W Film | |
| 103-295-01A | Diode, Low Voltage | 3243 | 63-10243-80 | 2.2K Ohm, #5% 1/2W Film |
| 103-142-01 | Diode, Low Voltage | R3244 | 63-7868 | 100K Ohm, +5% 1/2W Carbon |
| 103-142-01 | Diode, Low Voltage | R3261 | 63-10444-86 | 390 Ohm, +10% SW Wire Wound |
| 103-142-01 | Diode, Low Voltage | 3262 | 63-10565-65 | 510 Ohm, +10% 1/2 Film |
| 121-975 | Transistor, NPN | 3263 | 63-10565-65 | 510 Ohm, +10% 1/2W Film |
| 121-973, | Transistor, PNP, Shutdown | 3282 | 63-10235-96 | 10K Ohm, +5% 1/4W Film |
121-1037 Transistor, NPN, Forward Driver 121-975 Transistor, NPN, Shutdown 121-1040 Transistor, NPN, Reverse Driver ZENITH MONITOR — SWEEP BOARD REPLACEMENT PARTS LIST
c3ace
i | 289s ft | a he ween TS ; xe sore i “3429 © \ _ 7 9 ‘3425 ~ alee E Ee a a
raaee | 3 tt sto aw
oa Resor a mn
ot cram
| ie Te peaabeden =} + races te
hi hw 120 vic 1 i bl | oe 1 | % owe | Oy ee sear | a £ Sey Pl S44 7
SCHEMATIC FOR 9 -227-01 RGB COLOR MONITOR (MAIN BOARD)
ZENITH | RADIO CORP. C CHICAGO, ILL ice) ) N
MO51-00087-A024
6-20
ZENITH MONITOR — MAIN BOARD REPLACEMENT PARTS LIST MAIN BOARD (Continued)
Board Board
| 9-227 | 9-227 | Ref. No. | Part No. | Description | |||||
| Ret.No. PartNo. | Description | 9-227 | -01 | Ref.No. PartNo. | Description | 9-227 | -01 | Ref.No. PartNo. | Description |
7 CAPACITORS
| RESISTORS | RESISTORS (Continued) | RESISTORS (Continued) | 2101 | 22-7778-10A | 0.0068 MF, 100V +20% Polyester | |||||||||||
| x | X | RX2101 | 63-10565-32 22 Ohm, +5%, 1/2W Film | X | 2518 | 62-10295-73 | 1.1K Ohm, +5%, 1/4W Film | x | X | 3222 | 63-10235-40 47 Ohm, +5%, 1/4W Film | C2102 | 22-7775-24A | 0.1 MF, 100V +20% Polyester | ||
| x | X | A2102 — 63-10243-56 220 Ohm, +5%, 1/2W Film | x | R2519 — 63-10235-93 | 7.5K Ohm, +5%, 1/4W Fiim | x | X | 3231 | 63-9982 | 1 Ohm, | +10%, 2W Wirewound | C2103 | 22-7709-09C | 100 MF, 35V +50%—10% Electrolytic | ||
| x | X | R2103 | 63-10235-88 4.7K Ohm, +5%, 1/2W Film | X | R2519 | 63-10235-82 | 2.7K Ohm, +5%, 1/4W Film | x | X | A3ZBS_-63-10565-14 3.9 Ohm, | +5%, 1/2W Film | C2104 | 22-7613-24D | 0.01 MF, 50V +10% Disc | ||
| x | X — RX2104 63-10243-11 | 3 Ohm, +5%, 1/2W Film | x | R2520 | 63-10235-80 2.2K Ohm. +5%, 1/4W Film | x | X | 8234 | 63-10565-14 3.9 Ohm, | +5%, 1/2W Film | C2105 | 22-7390-02 | (0.47 MF, SOV +:20% Electrolytic | |||
| x | X | RX2105 63-10243-11 | x | R2521 | 63-10235-50 | 120 Ohm, +5%, 1/4W Film | x | X | 3239 | 63-10244-20 | 100K Ohm, +5%, 1/2W Film | C2106 | 22-7710-07C | 33 MF, 50V +50%-10% Electrolytic. | ||
| x | X | R2106 | 63-10235-72 | X | 2521 | 63-10235-48 | 100 Ohm, | +5%, 1/4W Film | x | X | 3241 | 63-8246 | 4 Ohm, 10W Wirewound | C2107 | 22-7615-03D | 0.0033 MF, 50V +80%-10% Disc |
| x | X | R2107 | 63-10235-66 | . | x | R2522 | 63-10235-74 | 1.2K Ohm. +5%, 1/4W Film | x | X | 3244 | 63-10840-40 47 Ohm, +5%, 3W Film, | C2110 | 22-7742-10 | 0.001 MF, 50V +10% Polyester | |
| x | X | R2108 | 63-10235-66 560 Ohm, +5%, 1/4W Film | x | R2523 | 63-10236-28 | 220K Ohm, +5%, 1/4W Film | Tin Oxide | C2111 | 22-7774-17A | 0.027 MF, 100V +10% Polyester | |||||
| x | X | R2109 | 63-10565 | 1 Ohm, +5%, 1/2W Film | X | 2523 | 63-10236-52 | 2.2 Meg Ohm, | +5%, 1/4W Film | x | X | R3245 | 63-10710A_—Thermistor | C2176 | 22-7725 | §80 MF, 50V +100%-10% Electrolytic |
| x | X | R2110 | 63-10565 = 1 Ohm, +5%, 1/2W Film | x | X | 2524 | 63-10235-90 5.6K Ohm, +5%, 1/4W Film | x | X | RX3246 63-10657-03 | 1.2 Meg Ohm, +20%, | C2501 | 22-7621-42C | 220 PF, S0V +5% Disc | ||
| x | X | R111 | 63-10565 = 1 Ohm, +5%, 1/2W Film | x | R2525 | 220 Ohm, | +5%, 1/4W Film | 1/2W Carbon | 2502 | 22-7621-42C | 220 PF, SOV +5% Disc | |||||
| Xx | X | R2112 | 63-10565 | 1 Ohm, +5%, 1/2WFilm | X | 2525 | 270 Ohh, | +5%, 1/4W Film | X | R3260 | 63-10243-96 | 10K Ohm, +5%, 1/2W Film | C2503 | 22-7621-42C | 220 PF, 50V +5% Disc | |
| x | X | R2113_ | 63-10243-60 330 Ohm, +5%, 1/2W Film | x | R2526 | £5%, 1/4W Film | X | 3261 | 63-10244-24 | 150K Ohm, +5%, 1/4W Film | 3201 | 22-7775-24A | 0.1 MF, 100V +20% Polyester | |||
| X | X | 2114 | 63-10235-72 | 1K Ohm, | +5%, 1/4W Film | X | 2526 | 63-10235-69 | X | R3262 | 63-10235-68 680 Ohm, +5%, 1/4W Film | C3204 | 22-7603 | 4.7 MF, 315V +100%~10% Electrolytic | ||
| x | X | 2115 | 63-10235-88 4.7K Ohm, +5%, 1/4W Film | x | R2527 — 63-10857-31 | SK Ohm, Control-Rotary | x | X | RG401 | 63-10236-46 | 1.2 Meg Ohm, +5%, 1/4W Film | 3205 | 22-3512 | 0.01 MF, 1KV +40%-20% Disc | ||
| x | X | R2116 | —63-10235-60 330 Ohm, +5%, 1/4W Film | Single-Blue | x | X | R402 | 63-10236-22 | 120K Ohm, | +5%, 1/4W Film | 3206 | 22-7603-01A | 10 MF, 315V +100%~10% Electrolytic | |||
| x | X | R214? | 63-10235-80 2.2K Ohm, +5%, 1/4W Film | X | R2527 | 63-10857-26 | 800 Ohm, Control-Rotary | x | X | R3403_ | 63-10235-86 | 3.9K Ohm, +5%, 1/4W Film | 3207 | 22-7742-10 | 0.001 MF, 50V 10% Axial | |
| x | X | R2118 | 63-10235-88 4.7K Ohm, | +5%, 1/4W Film | Single-Blue Cut-Off | x | X | —R3404 | 63-10235-86 | 3.9K Ohm, +5%, 1/4W Film | C3208 | 22-7742-10 | 0,001 MF, 50V +10% Axial | |||
| x | X | 2119 | 63-10235-54 | 180 Ohm, +5%, 1/4W Film | x | R2528 | 63-10857-30 | 1K Ohm, Control-Rotary | x | X | R340 | 63-10236-08 | 33K Ohm, +5%, 1/4W Film | 3209 | 22-7395 | 470 PF, S00V +5% Disc |
| x | X | 2120 | 63-10565-08 | 2.2 Ohm, +5%, 1/2W Film | Single-Yellow | x | X | 3406 | 63-10235-68 | 680 Ohm, | +5%, 1/4 Film | C3234 | 22-7398 | 470 PF, S00V +5% Disc | ||
| x | X | 2121 | 63-10243-52 | 150 Ohm, +5%, 1/2W Film | X | R2528 | 63-10857-26 | 800 Ohm, Control-Rotary | x | X | R3407 | —63-10236-18 82K Ohm, +5%, 1/4W Film | C3236 | 22-7861-14 | 2200 MF, 35V +20% Electrolytic | |
| x | X | 2122 | 63-10243-52 | 150 Ohm, +5%. 1/2W Film | Single-Blue Drive | x | X | R3408 | 63-10236-04 22K Ohm, +5%, 1/4W Film | C3246 | 22-7603-01A | 10 MF, 315V +100%~10% Electrolytic | ||||
| x | X | 2125 | 63-9023-02 | 550 Ohm, +20%, Control- | x | R2529 | 63-10235-76 | 1.5K Ohm, +5%, 1/4W Film | x | X | R340 | 63-10857-17 | 100K Ohm, Control-Rotary | C3247 | 22-7860-12 | 470 MF, 25V +20% Electrolytic |
| Rotary Single-GRA | X | R2529 | 63-10235-75 | 1.3K Ohm, +5%, 1/4W Film | Single-Green | 3249 | 22-7431-06 | 0.0047 MF, +20% Disc | ||||||||
| X | R2126 | 63-10243-66 560 Ohm, =5%, 1/2W Film | x | R2530 | 63-10235-93 | 7.5K Ohm, +5%. 1/4W Film | x | X | 3410 | 63-10236-31 | 300K Ohm, | +5%, 1/4W Film | CX3250 | 22-7431-08 | 0.0047 MF, +20% Disc | |
| x | 2126 | 63-10243-53_ | 160 Ohm, +5%, 1/2W Film | X | R2530 | 63-10235-82 | 2.7K Ohm, +5%, 1/4W Film | x | X | 3411 | 63-10236-03 | 20K Ohm, +5%, 1/4W Film | C3251 | 22-7811 | 0.001 MF, 1KV +10% Disc | |
| X | 2127 | 63-10243-69 | 750 Ohm, +5%, 1W Carbon | x | R2531 | 63-10235-80 | 2.2K Ohm, +5%, 1/4W Film | x | X | RB412_ | 63-10236-13 | 51K Ohm, +5%, 1/4W Film | C3252 | 22-7811 | 0.001 MF, 1KV +40% Disc | |
| x | R2128 | 63-10243-66 560 Ohm, +5%. 1/2W Film | x | R2532 | 63-10235-50 | 120 Ohm, | +5%, 1/4W Film | x | X | R3413__63-10236-07 30K Ohm, +5%, 1/4W Film | C3253 | 22-7811 | 0.001 MF, 1KV +10% Disc | |||
| X | P2128 | 63-6058 | 510 Ohm’ +5%, 1W Carbon | X | R2532 | 63-10235-48 | 100 Ohm, +5%, 1/4W Film | Xx | X | 3414 | 63-10235-98 | 12K Ohm, +5%, 1/4W Film | 3254 | 22-7404-08 | 22 MF, 16V +20% Electrolytic | |
| X | R2129 | 63-10243-65 510 Ohm, +5%, 1/2W Carbon | x | 2533 | 63-10235-74 | 1.2K Ohm, +5%, 1/4W Film | x | X | R3415 | 63-10236-02 | 18K Ohm, +5%, 1/4W Film | 63256 | 22-7508-05B | 2200 MF, 35V +50%~10% Electrolytic | ||
| x | R2501 | 63-10236-28 220K Ohm, +5%, 1/4W Film | R2534 | 63-10235-52 | 150 Ohm, +5%, 1/4W Film | Xx | X | —R3417_ | 63-10243-60 330 Ohm, +5%, 1/2W Film | C3257 | 22-7395 | 470 PF, 500V | +5% Disc | |||
| X | R2501 | 63-10236-52_ 2.2 Meg Ohm, +5%, 1/4W Film | x | R2535 | 63-10235-52 | 150 Ohm, +5%, 1/4W Film | x | X | 3418 | 63-10857-08 2K Ohm, Control-Rotary | 3401 | 22-7613-24D | 0.01 MF, SOV | +10% Disc | ||
| x | X | R2502 | 63-10235-90 5.6K Ohm, +5%, 1/4W Film | x | R2536 | 63-10235-52 | 150 Ohm, +5%, 1/4W Film | Single-Yellow | 3402 | 22-7406-01 | 1.0 MF, 35V +20% Electrolytic, | |||||
| x | R2503 | 63-10235-56 220 Ohm, +5%, 1/4W Film | x | 2537 | 63-10235-52 | 150 Ohm, 5%, 1/4W Film | x | X | R3419 | 63-10235-84 | 3.3K Ohm, +5%, 1/4W Film | £3403 | 22-7773-18A | 0.033 MF, 100V +5% Polyester | ||
| X | 2503 | 63-10235-58 270 Ohm, +5%, 1/4W Film | x | R2538 | 63-10235-56 220 Ohm, +5%, 1/4W Film | x | X | R3420 | 63-10236-10 | 39K Ohm, +5%, 1/4W Film | C3404 | 22-7773-17A | 0.027 MF, 100V | +5% Polyester | ||
| x | R2504 | 63-10235-80 2.2K Ohm, | +5%, 1/4W Film | X | 2538 | 63-10235-48 | 100 Ohm, +5%, 1/4W Film | x | X | 3421 | 63-10235-73 | 1.1K Ohm, +5%, 1/4W Film | C3405 | 22-7775-10A | 0.0068 MF, 100V +20% Polyester | |
| X | R2504 | 63-10235-69 750 Ohm, | +5%, 1/4W Film | x | R2539 | 63-10235-56 220 Ohm, +5%, 1/4 Film | x | X | 3422 | 63-10243-60 | 330 Ohm, +5%, 1/2W Film | 3407 | 22-7710-01A | 1.0 MF, 50V +50%~10% Electrolytic | ||
| x | R2505 | 63-10857-11_ | 5K Ohm, Control-Rotary | X | 2539 | 63-10235-48 | 100 Ohm, +5%, 1/4W Film | x | X | RB423° | 63-10243-60 330 Ohm, +5%, 1/2W Film | c3409 | 22-7709-09C | 100 MF, 35V +100%~10% Electrolytic | ||
| Single-RED | x | R2540 | 63-10235-56 220 Ohm, +5%, 1/4W Film | x | X | 3424 | 63-10235-72 | 1K Ohm, +5%, 1/4W Film | C3410 | 22-7404-06A | 22 MF, 16V +20% Electrolytic NP | |||||
| X | 2505 | 63-10857-27 | 800 Ohm, Control-Rotary | X | 2540 | 63-10235-48 | 100 Ohm, | +5%, 1/4W Film | Xx | X | 3425 | 63-10235-88 4.7K Ohm, +5%, 1/4W Film | 3411 | 22-7708-09 | 100 MF, 25V +50%-10% Electrolytic | |
| Single-Red Cut-Off | X | 2541 | 63-10235-54 | , 1/4W Film | x | X | R3428 | 63-10235-82 2.7K Ohm, +5%, 1/4W Film | C3412 | 22-7710-01C_ | 1.0 MF, 50V +50%~10% Electrolytic | |||||
| x | R2506 | 63-10857-30 | 1K Ohm, Control-Rotary | X | R2542 | 63-10235-53 | , 1/4 Film | x | X | 3429 | 63-10235-76 | 1.5K Ohm, +5%, 1/4W Film | C3413 | 22-7562-32 | 0.47 MF, 100V +5% Polyester | |
| Single-Yellow | X | R2543 | 63-10235-54 | . 1/4 Film | x | X | R3431 | 63-10235-80 | 2.2K Ohm, +5%, 1/4W Film | C3414 | 22-7774-16A | 0.022 MF, 100V +10% Polyester | ||||
| X | R2506 | 63-10857-27 800 Ohm, Contro!-Rotary | X | 2544 | 63-10235-54 | 180 Ohm, +5%, 1/4W Film | x | R3432 | 63-10235-55 | 200 Ohm, +5%, 1/4W Film | C3419 | 22-7751-39 | 180 PF, 50V +5% Axial | |||
| Single-Red Drive | X | 2645 | 63-10235-54 180 Ohm, | +5%, 1/4W Film | X | 3432 | 63-10235-79 | 2K Ohm, £5%, 1/4W Film | 3420 | 22-7710-01C | 1.0 MF, 50V +50%-10% Electrolytic | |||||
| x | R2507 | 63-10235-76 | 1.5K Ohm, +5%, 1/4W Film | X | R2546 | 63-10235-53_ | 160 Ohm, +5%, 1/4W Film | x | X | P3433 | 63-10236-20 | 100K Ohm, | +5%, 1/4W Film | 3421 | 22-1773-188 | 0.033 MF, 100V +5% Polyester |
| X | R2507 | 63-10235-75 | 1.3K Ohm, +5%, 1/4W Film | X | 2548 | 63-10235-67 | 620 Ohm, +5%, 1/4W Film | x | X | 3434 | 63-10236-22 | 120K Ohm, +5%, 1/4W Film | C3422 | 22-7613-24D | 0.01 MF, 50V +10% Disc | |
| X | R2508 | 63-10235-93_ 7.5K Ohm, | +5%, 1/4W Film | X | R2549 | 63-10235-67 | 620 Ohm, +5%, 1/4W Film | x | X | 3435 | 63-10235-63 430 Ohm, +5%, 1/4W Film | C3423 | 22-7613-08D | 470 PF, SOV +10% Disc | ||
| x | R2508 | 63-10235-82 | 2.7K Ohm, | +5%, 1/4W Film | X | 2550 | 63-10235-32 22 Ohm, +5%, 1/4W Film | x | X | R3436 | 63-10235-72_ | 1K Ohm, +5%, 1/4W Film | C3424 | 22-7742-05 | 390 PF, SOV +10% Axial | |
| x | R2509 | 63-10235-80 2.2K Ohm, +5%, 1/4W Film | X | 2552 | 63-10235-32 | 22 Ohm, +5%, 1/4W Film | x | X | R3439_ | 63-10243-79 | 2K Ohm, +5%, 1/2W Film | C3425, | 22-7742-10 | 0.001 MF, SOV +10% Axial | ||
| Xx | R2510 | 63-10235-50 | 120 Ohm, +5%, 1/4W Film | X | 2554 | 63-10235-32 22 Ohm, +5%, 1/4W Film | x | X | R3440_ | 63-10235-86 | 3.9K Ohm, +5%, 1/4W Film | C3426 | 22-7742-10 | 0.01 MF, 50V +10% Axial | ||
| X | 2510 | 63-10235-48 | 100 Ohm, +5%, 1/4W Film | x | X | 3201 | 63-10235-59 300 Ohm, +5%, 1/4W Film | Xx | R3441 | 63-10857 | 100 Ohm, Control-Rotary | ©3427 | 22-7647-35C | 150 PF, +10% Axial | ||
| Xx | R2511 | 63-10235-74 | 1.2K Ohm, +5%, 1/4W Film | x | X | 3202 | 63-10235-44_ 68 Ohm, +5%, 1/4W Film | Single-Horizontal Center | 3428 | 22-7774-12 | 0.01 MF, 100V +10% Polyester | |||||
| X | R2511 | 63-10235-67 620 Ohm, +5%, 1/4W Film | x | X | 3203 | 63-10235-52 | 150 Ohm, +5%, 1/4W Film | X | 3441 | 63-10857-02 250 Ohm, Control-Rotary | C3428 | 22-7774-20A | 0.047 MF, 100V +10% Polyester | |||
| x | R2512 | 63-10236-28 220K Ohm, +5%, 1/4W Film | x | X | R3205 | 63-7781 | 820 Ohm, +5%, 1/2W Carbon | Single-Horizontal Center | (on-01 version) | |||||||
| X | R2512 | 63-10236-52 2.2 Meg Ohm, +5%, 1/4W Film | x | R3206 | F-11851 | 12 Ohm, +10%, 10W Resistor | x | X | 3442 | 63-10235-86 | £5%, 1/4W Film | 3429 | 22-7405-04 | 4.7 MF, 25V +20% Electrolytic NP | ||
| x | X | R2513 | 63-10235-90 5.6K Ohm, +5%, 1/4W Film | & Splice Assy. | x | R3443 | 63-10235-65 | . | C3429 | 22-7406 | 0.47 MF, 35V +20% Electrolytic NP | |||||
| x | R2514 | 63-10235-56 220 Ohm, +5%, 1/4W Film | X | 3206 | 63-10460-50 12 Ohm, +10%, 10W | X | R3443_—63-10235-80 | 2.2K Ohm, +5%, 1/4W Film | (on-01 version) | |||||||
| X | R2514 | 63-10235-58 | 270 Ohm, +5%, 1/4W Film | Wirewound | x | X | R3444_ | 63-10235-60 330 Ohm, +5%, | 1/4W Film | 3430 | 22-7613-24D | 0.01 MF, 50V +10% Disc | ||||
| x | R2515 | 63-10235-80 2.2K Ohm, | +5%, 1/4W Film | x | X | 3210 | 63-10420-31 | 2 Ohm, +5%, 2W Wirewound | x | X | R3445 | 63-10235-80 2.2K Ohm, +5%, 1/4W Film | 3431 | 22-7774-16A | 0.022 MF, 100V +10% Polyester | |
| R2515 | 63-10235-71 | 910 Ohm, +5%, 1/4W Film | x | X | 3212 | 63-10235-76 | 1.5K Ohm, +5%, 1/4W Film | X | 3446 | 63-10235-72 | 1K Ohm, +5%, 1/4W Film | C3434 | 22-7742-06 | 470 PF, 50V +10% Axial | ||
| x | R2516 | 63-10857-32 5K Ohm, Control-Rotary | x | R3213 | 63-10235-83 | 3K Ohm, +5%, 1/4W Film | x | R3449 | 63-10235-76 | 1.5K Ohm, +5%, 1/4W Film | C3436 | 22-7613-24C | 0.01 MF, 100V +10% Disc | |||
| Single-Green | X | R3213__63-10235-86 3.9K Ohm, +5%, 1/4W Film | x | 3451 | 63-10235-82 | 2.7K Ohm, +5%, 1/4W Film | 3450 | 22-7739-29A | 0.27 MF, 100V +10% Polyester | |||||||
| X | R2516 | —63-10857-25 800 Ohm, Control-Rotary | x | X | 3214 | 63-10235-74 | 1.2K Ohm, +5%, 1/4W Film | X | 3451 | 63-10235-88 4.7K Ohm, +5%, 1/4W Film | C3450 | 22-7619-41C | 200 PF, 50V +5% Disc | |||
| Single-Green Cut-Off | x | R3215 | 63-10244-38 60K Ohm, +5%, 1/2W Film | x | X | R3452__63-10235-92 | 6.8K Ohm, +5%, 1/4W Film | (on-01 version) | ||||||||
| x | 2517 | 63-10857-30 | 1K Ohm, Control-Rotary | X | R8215 | 63-10244-40 | X | 3453 | 63-10235-75 | 1.3K Ohm, +5%, 1/4W Film | C3461 | 22-7710-01C | 1.0 MF, SOV +50%~10% Electrolytic | |||
| Single-Yellow | x | X | R3216 | 63-10244-25 | ; | x | X | R3461 | 63-10236 | 15K Ohm, +5%, 1/4W Film | 03462 | 22-7710-01C | 1.0 MF, 50V +50% 10% Electrolytic | |||
| X | 2517 | 63-10857-25 | 800 Ohm, Control-Retary | x | X | R3217 | 63-10244-33_ 360K Ohm, +5%, 1/2W Film | x | X | 3462 | 63-10236-13 51K Ohm, +5%, 1/4W Film | C3462 | 22-7739-09 | 0.0056 MF, 100V +10% Polyester | ||
| Single-Green Drive | x | X | 3218 | 63-10235-80 | 2.2K Ohm, +5%, 1/4W Film | (on-01 version) | ||||||||||
| x | R2518 | 63-10235-76 | 1.5K Ohm, +5%, 1/4W Film | X | 3219 | 63-10244-38 | 560K Ohm, +5%, 1/2W Film | 3463 | 22-7508 | 47 MF, 35V +20% Electrolytic |
6-21
ZENITH MONITOR — CRT SOCKET BOARD MAIN BOARD (Continued) REPLACEMENT PARTS LIST
| Ref. No. | Part No. | Description |
SEMICONDUCTORS CRT SOCKET (9-155-10)
| CR2104 | 103-142-01 | Diode, Low Voltage | |||
| CR2105 | 103-254-01 | Diode, Low Voltage | RetsNos | PartNo. | Description |
| cR2106 | 103-254-01 | Diode, Low Voltage | |||
| CR2107 | 103-254-01 | Diode, Low Voltage | CAPACITORS | ||
| CR2501 | 103-142-01 | Diode, Low Voltage | 5101 | 22-4671 | 0.01 MF, 1.5KV, +80%-20% Disc |
| cR2502 | 103-142-01 | Diode, Low Voltage | 5102 | 22-3512 | 0.01 MF, 1KV, +40%-10% Disc |
| CR2503 | 103-142-01 | Diode, Low Voltage | |||
| CR3202 | 103-330A | Diode, Low Voltage | TRANSFORMERS & COILS | ||
| CR3205 | 103-309-01 | Diode, Zener 10V1W | Ls102 | 20-3887-28E | 220MH Peaking |
| CR3206 | 103-254-01 | Diode, Low Voltage | 5103 | 20-3887-28E | 220MH Peaking |
| CR3208 | 103-3260 | Diode, Low Voltage | 5104 | 20-3887-28E | 220 MH Peaking |
| CR3210 | 103-254-01 | Diode, Low Voltage | |||
| CR3211 | 103-254-01 | Diode, Low Voltage | SEMICONDUCTORS | ||
| ae | qosGeek, | Diode? rete vonce | Q5101 | F7510 | Transistor, NPN, Video Out, Blue |
| GR3219 | 103-3308 | Diode, Low Voltage | 5102 | F7510 | Transistor, NPN, Video Out, Red |
| R3223 | 103-3300 | Diode, Low Voltage | Q5103 | F7510 | Transistor, NPN, Video Out, Green |
| CR3224 | 103-330 | Diode, Low Voltage | |||
| CR3231 | 103-315-06A | Diode | RESISTORS | ||
| cR3232 | 103-315-06A | Diode | R5101 | 63-10840-88 | 4.7K Ohm, 45%, 3W Film |
| R3233 | 103-315-06A | Diode | R5102 | 63-7785 | 1K Ohm, +10%, 1/2W Carbon |
| CR3234 | 103-315-06A | Diode | 5103 | 63-7785 | 1K Ohm, +10%, 1/2W Carbon |
| CR3235, | 103-2844 | Diode, Low Voltage | R5104 | 63-10235-64 | 180 Ohm, +5%, 1/4W Film |
| CR3401 | 103-142-01 | Diode, Low Voltage | R5105 | 63-10235-48 | 100 Ohm, +5%, 1/4W Film |
| CR3404 | 103-143-01 | Diode, Low Voltage | R5106 | 63-7785 | 4K Ohm, #10%, 1/2W Carbon |
| CR3405, | 103-142-01 | Diode, Low Voltage | R5107 | 63-7785 | 1K Ohm, +10%, 1/2W Carbon |
| CR3406 | 103-142-01 | Diode, Low Voltage | R5108 | 63-7785 | 1K Ohm, +10%, 1/2W Carbon |
| CR3408 | 103-279-14 | Diode, Zener 6.8V 1/2W | R5109 | 63-7785, | 1K Ohm, +10%, 1/2W Carbon |
| Q2101 | F-10896 | Transistor & Heat Sink Assy. | S110 | 63-7785 | 1K Ohm, +10%, 1/2W Carbon |
| Q2102 | F-10896 | Transistor & Heat Sink Assy. | RS111 | 63-7799 | 2.2K Ohm, +10%, 1/2W Carbon |
| Q2103 | 121-975 | Transistor NPN | 5112 | 63-10840-88 | 4.7K Ohm, +5%, 3W Carbon |
| Q2104 | 121-1064 | Transistor PNP | R5113, | 63-10840-88 | 4.7K Ohm, +5%, 3W Carbon |
| Q2501 | 121-1019 | Transistor PNP | S114 | 63-10235-54 | 180 Ohm, +5%, 1/4W Film |
| Q2502 | 121-895 | Transistor NPN | 5115, | 63-10235-54 | 180 Ohm, £5%, 1/4W Film |
| 2502 | 121-551 | Transistor NPN |
(on-01 version) MISCELLANEOUS
| 2503 | 121-1019 | Transistor PNP | 5A2 | 86-799 | Stake Connector 4/.156 |
| Q2504 | 121-895 | Transistor NPN | 5C2 | 86-799 | Stake Connector4/.156 |
| 2504 | 121-551 | Transistor NPN | 5H3 | 86-799 | Stake Connector 2/.156 |
| (on-01 version) | 5X7 | 86-799 | Stake Connector 1/.312 | ||
| 2505 | 421-1019 | Transistor PNP | ‘A-10008 | CRT Socket | |
| 2506 | 121-895 | Transistor NPN | |||
| Q2506 | 121-554 | Transistor NPN |
(on-01 version)
| 2507 | 121-1019 | Transistor |
| 2508 | 121-1019 | Transistor |
| Q2509 | 121-1019 | Transistor |
| 93200 | F-12737 | Transistor & Heat Sink Assy. |
| Q3201 | 121-499-01 | Transistor NPN Regular Feed Back |
| 93202 | 121-1034 | Transistor NPN |
| 93203 | 121-1059 | Transistor PNP |
| Q3401 | 121-895, | Transistor NPN |
| 3402 | 121-986 | Transistor PNP |
| Q3403 | 121-985 | Transistor NPN |
| 3404 | 121-895 | Transistor NPN |
| 03405 | 121-895 | Transistor NPN |
TRANSFORMERS & COILS
| L2502 | 20-3887-01 | Coil Peaking 1.2 UH |
| 1.2503 | 20-3887-01 | Coil Peaking 1.2UH |
| 12504 | 20-3887-01 | Coil Peaking 1.2 UH |
| (3201 | 20-2021 | Coil Peaking 100 UH |
| Lx3202 | 95-3501-01 | Transformer Choke 60 UH |
| 3401 | 20-3831 | Coil Peaking 663 UH |
| 3402 | 20-3998 | Coil Peaking 39 UH |
| 1.3402 | 20-4026 | Coil Turnable 39 UH |
(on-01 version)
FIL FIL
9-155-10 | (204-960) I
NOTES: (USED WITH CIRCUIT REFERENCE DESIONATORS) A. PA. = SEE PARTS LIST FOR APPLICABLE USAGE. —o—* = JUMPER WIRE USED INSTEAD. Cl —@ = @ = PROVISION ON PRINTED CIRCUIT BOARD. M051-00087-A022 SCHEMATIC FOR SeHie KR MONTTOR
DAG SIONAL GROUND GROUND RADIU ZENITH ( LURF . | CHILAGL» TL. _ i 6-23

This page is a drawing, shown as the original scan.
F-13473 [
3710657203 tte
To. 0.C. GROUNC
IMF URTANT WHEN SERVIZING THIS CHASEIS, INDER Mt TRS: SHCUCD THE ORISINAL DE - SIs SF MCCIFIEC OR ALTEREC WITHOUT PERMISSION FRUM THE ZENITH RACIC CCR PORATICN. ALL COMPONENTS SHOULD BE_RE- TUENTICAL TO ROUIT. ANC WIRING AND
TIGN CF REFAIRS. UopectaL 15 ARE ALSC _UGEL_TC FRE- + VENT SHOSK ANC FIRE HAZARD. THEE AREAS | ARE SHACEL CN THE SCHEMATIC FOX EASY ICENTIFICATICN. THE LETTER "x" INCLUDED, ' ITEM NUMBER LESIGNRTES: SPESTAL SAFE COMPONENT: IN THESE ARE WHICH ARE REGJIREL Ti MAINTAIN SAFE PER~ FORMANCE. NO CEVIATIUNS ARE ALLCHEL WITHCUT PRIOR APPR VAL SY THE PRUCUCT FETY ENGINEERING LEFARTMENT . JLT CTAGRAY RY USCALICNA: CIFFER FRU THE SEC. THIS HAY, IMEEM THE LATEST SAFETY AC FERFORMATICE IMPROVEMENT EHANGES INTC THE SET Ic NCT Ob AYEC UNTIL THE NEW SERVI-€ SiTERAT Ihe TS PRINTED.
MO051-00087-A025
| 3v3 | — | fa | — |
ao} |
| MAIN MOOULE | —t | 3OOMF ly | + | |
| (SEE CHART) | | | | | a | - |
3 [eaaco Lia] H 22-7735-01
| = | 3W3 | f | 7 |
5 5 303
| ooo | fis] | . | deo] |
| " | | | “2R3 |
El ur
| i | | | uy |
| c _. SWEEP MODULE (SEE CHART)
E x
ooooaa ooo 383 3R3 foo ooo
Ls 18 hd t ¢ 4 t
| 2AS | 285 | 3F3 | 378 | 3s8 | 3R8 | |||||
| [eeee | ooo00 | aoa | | 0 | e| | [e = =| | fe = o | i | 3 | | | | |
~ {a} J HV POWER ASSEMBL: MBLY YOKE
| [ | Liu | an | (SEE CHART) |
AIR
’ 10 TO DEGAUSSER 23 (I
7 aa
| i | i | 353 | (o] |
| soo | ia | . | PcB |
uw Ls] ASSEMBLY WIGTH STEP
| — | TL. | ee | (SEE CHART) |
ee VIDEO gut ™~ (SEE CHART)
SH3
| feo] | [o]sxs | . | rt | | |
| 4 | = | {3} | 7 | OO |
is INTER ! =e) iim VIDEO ‘DAG
ZENTTH RAG TO Li AP | CHICASU, fue.
CONNECT FOR GAME
MONITOR
6-25
VII. Coin Door Maintenance
SPECIAL NOTE: If you have any questions about the coin acceptors in your game(s), please feel free to contact their manufacturers. Each manufacturer's name is PROMINENTLY imprinted on every acceptor mechanism. Metal mechanisms only: COIN MECHANISMS, INC. 817 Industrial Drive Elmhurst, IL 60126 Phone (312) 279-9150
COIN DOOR MAINTENANCE
METAL COIN ACCEPTOR MECHANISMS
Periodically, the metal coin acceptor mechanism(s) must be removed from the coin door and cleaned.
- Make sure the power to the game is off.
- Unlock and open the coin door.
TO REMOVE PUSH LATCHES DOWN
PLACE PEGS IN SLOTS TO REPLACE PULL MECHANISM OUT Metal and Plastic mechanisms: COINCO COIN ACCEPTORS, INC. 860 Eagle Drive Bensenville, IL 60106 Phone (312) 766-6781
- Remove the coin acceptor mechanism as shown in Figure 5-1. Push down on the two spring loaded latches. O While holding the fatches down, pull the top of the coin acceptor mechanism toward you. D Release the latches and lift out the coin acceptor mechanism.
PUSH MECHANISM IN
Figure 5-1 Removing and Replacing the Coin Acceptor
- Clean the magnet of all foreign particles. See Figure 5-2. O This may be accomplished by swinging the gate open as shown in the above figure.
- Remove the cradles and undersize levers and clean the bushings. (A pipe cleaner makes a good bushing cleaner.) QO Also clean the pivot pin.
- Whenever needed, the coin acceptor should be cleaned with hot water and cleanser in the following manner: O Place the coin acceptor in boiling water for about ten minutes.
O Next, use a brush and kitchen cleaner to remove all remaining foreign matter from the unit. Q Rinse the coin acceptor in clean boiling water. O Dry the coin acceptor thoroughly by using filtered compressed air to blow it dry.
GATE OPEN AS SHOWN CLEAN MAGNET BY DRAGGING A SCREWDRIVER BLADE ACROSS SURFACE
Figure 5-2 Cleaning the Metal Coin Acceptor
7-2
- To lubricate the coin acceptor: O Use ONLY powdered graphite and put it ONLY on the moving parts of the coin acceptor. These parts are called out in Figure 5-3. O Be extremely careful to keep the powdered graphite away from paths that are traveled by the coins.
- WARNING — DO NOT USE OiL TO LUBRICATE THE COIN ACCEPTOR.
- Check the coin chute for obstructions such as: paper, gum, etc. 9, Reinstall the coin acceptor to the coin door. See Figure 5-1. O Place the two pegs at the coin acceptor's base into their retaining slots. 1 Now push the top of the coin acceptor toward the coin door until it snaps in place and is held there by the two spring loaded Jatches.
- Close and lock the coin door.
APPLY POWDERED GRAPHITE HERE
UNDERSIZE LEVER
“E” RINGS
CRADLE
Figure 5-3 Lubricating the Metal Coin Acceptor
SQUEEZE PINS TOGETHER TO UNLOCK cx, “See. SWING BOTH GATES OPEN
HOLDING BOTH GATES TOGETHER, PUSH UP AND PULL OUT
Figure 5-4 Opening the Plastic Coin Acceptor
PLASTIC COIN ACCEPTOR MECHANISMS
The plastic coin acceptor mechanism(s} must be removed periodically from the coin door and cleaned.
- Make sure the power to the game is off.
- Unlock and open the coin door.
- Remove the coin acceptor mechanisms(s) as shown in Figure 5-1. O Push down on the two spring loaded latches. O While holding the latches down, pull the top of the acceptor mechanism toward you. O Release the latches and lift out the mechanism. 4, Squeeze the two pins indicated in Figure 5-4 together to open the mechanism and break it down into its three basic parts. O Clean the mechanism in hot soapy water. It never rusts. O Rinse the mechanism in clean hot water and allow it to dry. O Reassemble the mechanism (it never needs lubrication).
- Check the coin chute for obstructions such as: paper, gum, etc.
- Reinstall the coin acceptor to the coin door. See Figure 5-5. O Place the two pegs at the coin acceptor's base into their retaining slots. O Now push the top of the coin acceptor toward the coin door until it snaps in place and is held there by the two spring loaded latches.
- Close and lock the coin door.
7-3
ACCEPTOR CAN BE SET TO ACCEPT U.S. QUARTERS ONLY OR BOTH U.S. AND CANADIAN QUARTERS.
SLIDE MAGNET TO EXTREME RIGHT (AS. SHOWN) TO ACCEPT BOTH U.S. AND CANADIAN QUARTERS.
rs
TO ACCEPT U.S. QUARTERS ONLY, SLIDE MAGNET TO EXTREME LEFT.
Figure 5-5 Changing the Plastic Coin Acceptor to Accept American or Canadian Quarters
7-4
VIII. Schematics & Wiring Diagrams
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
DESIGNATION LIST
‘DRAWING 2518 FW ‘k082-90812-0000 ‘Mosi~00945-0006
a2
MT 89
mT 90 4948-00002-0000 iat 2ns772 Fer Riot FERRITE SEAD 0.18
FILTER ASS'Y
DOMESTIC fl
' EXPORT 9 )--- 7 anze0s, o.tMe <>
Festvew +12V7 44M
vA JE-11 VIDEO ORIVERS 5-9 WSC Ro
EARTH GNO < _ OPTIONAL GND,
VOLTAGE. @ FUSE VALUE VARIES WITH APPLICATION
FROM X-¥ MONTOR XFMR (OR ISOLATION XFMR. rile 18072" +, nos j 10 cio
| sw | | unsos | - | a70UF |
4 18-6 “SENSECi2v)
vaio
aise 47 LOGIE BRO Kk JS:12 misc
| L | SENSE_ | tf | i | |
| common | Tani | | | ||
| Uo 0.28.uN | aie | 0208 ineoo) | . | wet wear |
| ly | ag | — | ||
| | | 205 | 0204 | 7 | Bo |
wl LS
| | | = | ~av | 45-1 _ COUNTER DRIVERS |
aes
| aus7me | FERRITE BEAD | Mo | +5V/7.5AMP 14-3 Lote @RD |
| Zs | = | 1 | 346" Locie eR |
| sw | | | $425 LOOIC BRO | |
| | | nn | 5-2 AUK, BRD | |
| | | 12K | J54 MISC |
a8 eenwvew
+] + | cior vo? 2 “108
| ovr | 00" | s70MF |
Por J4-9 Losic ano aur Lasie BRO
| a7 | - | t | J | $560 | LoaIe BRO |
| ome | cu | 5-5 AUX, ORD | |||
| sente | ca | 1 | ae | ||
| — | ) | 5-7 CONTROLS | |||
| COMMON. | 4 | 5-3 Mise |
14-2 SENSE (SV)
7 _ 35-10_COUNTER ATW
| _ | UNREG. AUX. V | J5-14_ CONTR LAMPS |
) OIG UNREG. FILTERED V__ 48.13 aupio cer. 101 Dios, clot
1_CONTR-LAMPS.
-2ee4 AC SYNCHRONIZATION —
ac synch
is Reser
| owe | 108 | avert | ||
| a | ee | th all oe qrnauy. | | | [iss av0i0 xr |
| ' | + | +8v | ne | ' |
wee4 '
| os | zoe | m | ; | ||
| R201 | 4nz8 | J® | e201 | oz02reos. | YS | 0 |
| 270 | A | 1 001MF aige | Lim | 320° |
oa 201
| t | 1) waren | 083m |
| 2 | ry | 1 |
| =. PUMP cHargeR - --------
Pe wee wor
its
io
203 R206 Walaa
o.oimt fooK
| U3 | g 0.087HF | A |
3800 R208
--ONE SHOT 2Ngao1 PROJECT ENG. L_OEKKER Rovere 1 PER. 2505. SATANWATOCLOW FULL MIDWAY MFG. CO. |
POWER SUPPLY I25VA ‘W/CKT SUPORT A082-90412-D000 MOS1-00945-D007
DESIGNATION LIST CROSS REFERENCE LIST
| DESIGNATION | DESCRIPTION | DESCRIPTION QTY DESIGNATION | PART NO | |||||
| C1,c2 | 4? mf 25v rd tant | Imf 50vaxce 6 | C?CIO | 0986-008001100 | ||||
| c3,c4 | 22mf bv" | cP2CP3 | ||||||
| c5,c6 | a70mf bv ax.elect | ‘ | 47 mf 25vrdtant 2 | CIC2 | 0986-008003100 | |||
| C?7-C1O | mf 50v ax.cr | 22mf By | | 2 | c3c4 | 0986-00800-1600 | |||
| CPI | 220mf 25v ax elect | 220mf 25vaxSlec 1 | CPI | 0986-00800-3200 | ||||
| CP2,CP3 | mf SOv ax.cr | tee | wae | 470mf 6v | 2 | csce | 0986-00800.1700 | |
| RIRZ | 2.7KN Vaw 5% CRBN, | INV 2w 5% | 4 | RS-RB | 0062-026D3-1Xxx | |||
| R3,R4 | 27s | " | _ | C2 | 2704 | 2 | R3R4 | 0062-068B3-1Xxx |
| R5-R8 | 1 Vw" | " | Ge) | 27K | 2. | -RLR2 | 0062 -199B3-1XXx | |
| U1,Uu2 | MB3730 | CE co | Gc | MB3730 | 2 | U1,U2 | O066 -188X x - Xx4x | |
| Jl | 3PIN STRT KKIS6 | cr | 2PINSTRTKKIS6 1 | J2 | 3000-16367 - 0200 | |||
| 2 | ; a | HSAL | HSA2 | Buh | 2 | dhe | 3000-16367 -0300 | |
| TI | ee | J | 00 -16367 -0400 | |||||
| ci | c2 | HEATSINK ASSY 2 | HSA, | A986 - | 00010000 | |||
| HSA1,2 | HEATSINK ASSY | CcEn | 40 | HSA2 | mee |
c4
| MH1-MH4 | HEYCO BUSHING | c3O | <@) | HEYCO BUSHING 4 MHI-MH4 | 0017-00042-0014 |
| fc | fF ce | | PC BOARD | | | AO80 - 90910-E000 | |
| cm) | (k2] | . |
\ Ea ae, _
THIS DWG IS CONFIDENTIAL & PROPERTY OF MIOWAY MFG CO. PR NG._ CM
| untessomenwise spec | fe | — | MIDWAY MFG. CO. | |
| CONCENTRICITY TI R 002 f°" | “9- 3 | FRANKLIN PK, IL. 60131 | A BALLYCO | |
| ANGLE | 212° Feec cH | Zz | A080-90910-E 000 | MO51-00986- E0IO |
DO NOT SCALE DWG ee
8-4
PIN 1
PIN 1
eeee @xr9H8ew
Ounewn Jt
J2 N.C. L. AUOIG t. SHIELD KEY V AUDIO RETURN A. AUDIO A. SHIELD Vv AUDIG Vv AUOIS
Vv AUDIO
I —T.lCUdle CHIPS CPL cp2 cP3 it 220uf 25v y° {* AL 2.7K Lé
lL
SHIELD
R2 2.7K R>
R
SHIELO
vauni6 =>
vaupIg =>
RETURN a
REVISIONS
MIDWAY MFG. CO. TLL
FRANKLIN PK
DO NOT SCALE DWG
NO. REQ'D IPER.
SCHEMATIC, DUAL POWER AMP
SPECIFIED DIM. TOLERANCES UNLESS MO51-00986-E0OI1
A082— 90910— E000
9/|_ /82
doo PATE
8-5
DESIGNATION LIST ' - - CROSS REFERENCE LIST
| DESGN. NO. | DESCRIPTION | DESCRIPTION | QTY DESGN. NO. | PART_NO. |
| cor | 4.7uf TANT I6V RAD. | -Ol wf SOV AX. CER. | CP1,3,4,6. | 0628-00800-0100 |
| A | 4.7 yt I6V RAD. TANT. | clot | 0628 - 00800-0200 | |
| cel | -Ol wf SOV AX. CER. | 10 wf I6V AX, ELECT. | cP2,5 | 0628-00800-0300 |
cp2 10 wf I6V AX, ELECT.
| cP 3 | -Olst SOV AX. CER. | 120 ohm 1/4W 8% | RIO6 | 0062-116B3-1XXxx |
| cP4 | -Olyf SOV AX. CER. | 4.7K 1/4W 5% | R101, 102, 111. | 0062-211B3-1Xxx |
| cps | lO.uf IGV AX. ELECT. | 6.2K 1/4W 5% | RIOB, 112 | 0062-217B3-IXxXx |
| cPé | -Ol wt SOV AX. CER, | 30K 1/4W 5% | RIOT | 0062 -249B3-IXxXXx |
| i | 91K 1/4W 5% | R108 | 0062-273B3-IXXX | |
| RIO1 | 4.7K 1/4W 5% | 200K 1/4W 5% | R103,104,109,110. 0062-269B3-1XXxXx |
R102 4.7K 1/4W 5%
| R103 | 200K 1/4W 5% | T4LS491 | ul | 0628-00803 -2700 |
| R104 | 200K 1/4W 3% | LM 339 | v2 | 0628-00803-2900 |
| R108 | 6.2K 1/4W 5%. | OPTICAL SENSOR | OPT! | 0628-00804-0100 |
R106 120 ohm 1/4W 5%
| R107 | 30K 1/4W 5% | 13 PIN KK-156 | tout | 3000-16387-131! |
| R108 | 91K 1/4W 8% | CRT.ANGLE PIN II OMITTED) |
R109 200K 1/4W 5%
| RIO | 200K 1/4W 5% | PLASTIC RIVET RND.HD. 2 MHOPTIA,IB. | 0017-00072-0091 |
Rit 4.7 K1/4W 5%
| Ril2 | 6.2 K1/4W 5% | P.C.B. | t | A082-91482-A000 |
opt! OPTICAL SENSOR vl 74LS491
| v2 | LM 339 | 1A, 1B——MHOPTIA, IB. |
vl 13 PIN KK-156 RT. ANGLE (PIN I OMITTED)
MH OPT IA,IB PLASTIC RIVET RND. HD.
A082-91482-A000 P.C.B.
; REVISIONS
PROJECT ENG: JOHN BOYDSTON USED ON KOZMIK KROOZ’R_| (Zafy | MIDWAY MFG.CO.
itt TOLERANCES ASSY DRAWING PART NO. . OPTICAL SENSOR A082-91482-A000 MO51 -OOI14 -A022 A084-91482 - A000
+5v tev rev +5V +5v
PaSe--5
prmnnn4
TaLsaot
200K Rios - E REVISIONS PROvECT ENG: JOHN BOYDSTON WES _KOZMIK KROOZ’R| Baty | MIDWAY MFG. CO DONOT SEALE OWS NO.REQD | PER FRANKLINPK ILL
‘SCHEMATIC DRAWING OPTICAL SENSOR A082 -91482-A000 A084 -91482~-A000 PART NO.
MOSI -OO114 -A023 SOSA 00 88ofoure 2/17/83
a7
DESIGNATION LIST DESIGNATION DESCRIPTION. DESIGNATION, DESCRIPTION Designation DESCRIPTION, ‘ Sees iSeneec tess patsire 2
ae yo he See oes :
awa [am roeue OGD z = [ran fone i ren Wr6.co. Post - oo8s9 - xose | Aoe2= 80010-6000 i
a8
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
CROSS REFERENCE LIST
| 1 | iad | * | ||
| De scRIPT DESIGNATION DESCRIP | SSRI Max. cen ag | EBBE-B 00-1000 | ||
| DESIGNATION DESCRIPTION | DESIGNATION DESCRIPTION | Ot yt SOV AK. ce 60 | "3, 078-10, | 0906-00800: 2500, |
. 7 cwe2-20,cP22-27, eur 74.820 . : c1e 100 pt ax. ELECT pe oa ecrateal rae) 7408
| f | x | : | fee 7474 | ||||||
| oie late | ie o3 T4L5 194 he oa fateees | £0 49-54,0036-6, | |||||||
| ice racsers an a | = | i | 63-67, cP69-71 | ||||||
| cru-bo.20-27 | peace parsley ies aaa | = | ai co oF & 9 6 8 A te | oat 25 ax. rant " | 0886 -00800-2400 | ||||
| Ne 20.8 Zi | 06 74.5187 | ca " | . | I ; | |||||
| 0729-33, 98.96, | a | eur TALsis7 | — | ; | 4 1 n | y | 0800. | ||
| eee ou sneer | 1c 07 users | i, | a, ts | 4 4 t:[ |t | 100 wt 25 Ax. evecr 2 | 0988 -00800-1800 | |||
| gaan | icm 7430 | : | I U : | 3 “ “ fe | 1K 1/4 CRON, FLM a | (0062- 17903- xxx | |||
| ata | ear ne | F | 4 | . | i som Se | : | 03660080800 | ||
| beg te een 1c M3 Tas T4 | Ee i | HCO PIN SIP | 1 | (0986 - 00804-1000 | |||||
| Ge tetas, iowa a6 | oe | ro ea ee | ana-2 | 2 | 0986-00803-2300 | ||||
| ©P4,1,21,20,34, | lees 74.5187 eae ue | ef] as | yet | : | ae | ; | ose6-o0e0s 2000 | ||
| eae ce.ee; soon 5 ax. tan: | COG raLsisr tom? Tass? | - ' | IU ' . | NaN | 7404 | ' | 10996 -00803-8300 | ||
| eea.ce. | i ? on U | + | te |] || Pte | 74504 | : | 0986 -00803-3i00 | |||
| wore 400 | 4 con rl | j | aos | ; | 0906 -00808- 3200 | ||||
| ers 74.504 icone ated | ~ omen on an | z | ea | 7a.s20 | 2 | 62,u1 | 0986-00803- 3400 | ||
| lore TaLs 374 a 7, | Ib | al | 7427 | i | Ne | (0886-00803-3800 | |||
| WOI-19,201,202, 1% 1/4W 5% | ciao Pesce tens 74us273 | || #2 | iG | moon | fa | 7430 | 5 | S253, K2, MINE 0986 -00803- 3600 | |
| ree tats'ar tone pacers | UT ur uyue | L | a | fae | i | ue | 0906-00803-4400 | ||
| as 7acs2as | l | 5 | fa | 7ausse | ‘ | oa7,car, | 0986-00803. 3700, | ||
| mae rac ikiow, | iene nce | , | zl | Usk | fy | rar | 2 | Kes | 0986 -00803-4500 |
| aus oP 1X SIP | tees rats e6 lon? racsis7 | a 3 | ert) ont a | “ | 74574 | 2 | H3, | 10986-00803- 4100 | |
| 103 ee ee | || | Te . Kit | : | 74.si87 | ‘8 | 42,3,4,5,6,7,05.6 0986 -00803- 2400 | |||
| wee neiuses | : BHT | u: U | £5,6,F5,6,66.N6, | ||||||
| tes Tacszes | u. | hale F | g | J6.C7M7IN7 | |||||
| leas eprom | i NCSA1.81,C1,01. 2806 1¢ SOCKET | | 3 | 3 | U ou i | SOT, | ||||
| "eae 74USi87 | te o6 Tetsier | ' | fim etey ore | Fa | ama | 3 | Kieu | 0986-00803-2800 | |
| ica 74 sis? | Some | ae homo’ eT] | 2 nei. | 0986 -00803-2600 | |||||
| eae ier | tems racses 1805,6,c8,6, 220m 1 sooKeT | H +! | TTI | 3 | il Hye die | ? | Loeineneneres | |||
| ie reusir | tower | 5K es | . | ela Bs | reuse | ° | 30s 09003-2900 | ||
| tone racist | emia ar | | UO Wyu vu UU uyue fje qf u | racseas | f | cry | 0366-00803-3000 | |||
| oar Tausisr | e raiTa ICSK6,L6. ——_18PIN IC SOCKET | a | 7 | a | racse73 | « | 24,7,04.N3 | 0986-00803-3800 | |
| ens | 4 | H | E | 4 | 74.s2e3 | 5 | 63.415 Ua.na, 0966-00803- 3900, | ||
| iene racsis7 s3.4,8 24 PIN RIGHT ANGLE conn, U, | Wo napn | ie ata | racsara | 2 | care | 0986 -00803-4000 | |||
| ro | wwicswe — JuMPeR wine | : | 7 | ot at Ts] | T Ig | 93422 | 4 | 95, 5,05, 5 (0986-00804-0800 | ||
| nae | ue 7430 | ‘ | FS | Ut | Bly sd | e3eze | ‘ | 85. 86,c5.c6 0966 60808-1010 | |
| pares TaLsi94 | 7 fees Bee uss oan | U IU Ut | U | 2U | spece | : | ee. Bec | ||
| ees eae | we | {| U U Orsee oacty mowar ura, &b | U | ono | ' | fe | ROW/EPROM OPTIONS KIT | |||
| 84 racsse | weve pacears POMHI-4 pc eo sPacER | BOTA mg ngsenves | : | 1 weer joszezoces..2000) | |||||
| : | eas s22 PCMHS-8 PC MTG SCREW | sot sae on | oon | conom | ' | ct tye | |||
| wees Ba | teve ral sis7 | | “eh : | ale a4 | new | d | Si. tuee) | wal | ||
| an | . | ofl | PAT. Penoine | 13 sly | JUMPER WRE | ° | 0 | ||
| fare rausse | ‘4080-91899-H000 Vi0.GEN. Pe | p fff | eq, | geen | 8 | Fpstroseeanien | |||
| wees ra | A Us Ue U : | » i | +n | mela | i | 4080-91399-€000 | |||
| lee 7430 | “ | 7 | is | ||||||
| tes aa | tees ra74 | bi | 24 RIGHT ANGLE CONN, 3 | 0986-00804. 470 | |||||
| he jausies: | ies 7461 | 280 socket” | 4 | 0986-00804-0300 | |||||
| es ad | leKs 422 | 22 SOCKET | e | 1€303,6,€8,6.18,45,L5,M5_0986-00804-0700 | |||||
| tees oa | pene cate | te PIN sockeT | z tes Ke Le | 0986-00804-0600 |
wes “
| ce azz | Po epspacer | 4 | Pom -Powns 0986-00701-00xF |
| seer r4us3e | PC MTG SCREW ‘ | POMHS-PoMHE 0017- 00101-0388 |
7 c0sH [ae KOT RROOZA] —ceiy | wIOWAY MFC.CO. eee a ae Co sepasiern_ = ao 7 NERATOR Pc. [rsT™ . =a woke ooy Dwe Mos!~ 00638 - A034 ial A08291399- HO00 sfc cenares reese
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
DESIGNATION LIST =
ep pp
SHES ESOT
= TSSEWaLY ORANG oa Sipersaue varceosso | wost ~ 90639 ~A038
a2
aa ar ar z= F Zlearae = ic ors
DESIGNATION _LLST CROSS REFERENCE LIST
| DESIGNATION NO. | DESCRIPTION | DESCRIPTION _QTY | DESIG.NO. | _PA\ | . |
| c1,c2 | 100 pf AX.CER SOV | 100 pf AX. CER.50V | cicz | 0639-00800-0003 | |
| -01 pf AX.CER.50V | CP2-cPI0 | 0628 -00800-0100 |
ELECT. I6V
| eet erie | iat Aa ER bOq | lo yf AX.ELECT.I6V | cP | 0628 - 00800-0300 |
| 43° | ohm 1/4. W5% | RI, RS | 0062 - 083 B3 -1Xxx |
5% ,
| ens | 903 | 13K" | "2% | R2,R6 | 0062-18582 -1Xxxx | ||||
| He | Hd | = | opr | nos2-01488-t000 | 27k " | "5% | RBR4,R7 | 0062-199 B3-IXXX |
| 43 | 5% | loo" «POT IveW | VRI,VR2 | 0639- 00804-0004 |
alas
| 13 k | 2% | ; as | a | Py | |
| - | - | T4LS244 | IC 1B,2A | 0639 - 00803-0003 |
2.7K 5%
| cee | cra | i) | 74393 | “ 2B,3A | 0639 - 00803-0005 | |
| VRI,VR2 | 100 ohm POT 1/8W | al | le | 40408 | « 3B,4A | 0639 - 00803 - 0004 |
| FE | 3 | a | 7 | |||
| tc 28 | 74.8 244 | [en eS | 74sc240 | 48 | 0639- 00803-0006 | |
| = | 74308 | ore | OFS | 1o- 40 wH COIL | Lice | 0639 - 00804-0003 |
| slots | — | 22 PIN KK-100 RT. | ut | 3000- 16366-2302 | ||
| “1B | 74L8 244 | a | oO’: | ANGLE PIN 18 OMITTED |
Pz : "2B 74393
| “38 | 40408 | u q | ANALOG JOYSTIC P.C. | A080- 91458-E000 |
“48 74.8c240 PAT. PENDING
| Li,Le | 10-40 pH COIL | uC) |
cP10 vt 23 PIN KK-I00 RT. ANGLE PIN 18 OMITTED vet ANALOG JOYSTIC P.c.
| A080-91458-E£000 | ANALOG JOYSTIC P.C. | (© 1982 BALLY MIOWAY MFG.,CO. ALL RIGHTS RESERVED |
PROJECT ENG: J. BOYDSTON use ONKOZMIK KROOZ"R] Batty | MIDWAY MFG. CO. ‘DO NOT SCALE OWG. cad IPER FRANKLINPK. ILL CunLestsencriee” ASSY. DWG.,ANALOG JOYSTIC P.C. | PART NO. A082 -91458- E000 - - A084 -91458-E000 MOS! 0028 6 E025)
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
8-16 DESIGNATION LIST
DESIGNATION NO.
cl Ri RE! Jl
J2 PC MHI-PCMH4 A080 -90509 -CO00
DESCRIPTION
-O | pf AX.CER.50V 1.5 Kohm |1/4W 5% SOLID STATE RELAY 4 PIN KK-I56 STR. CONN. PIN 3 OMITTED
CABLE CONNECTION P.C.MTG HDRW Pc. BOARD
CROSS REFERENCE LIST
sO lyf AX CER 50V 1.5 K ohm 1/74 W 5% SOLID STATE RELAY
PIN 3 OMITTED
CABLE CONNECTION P.C.MTG HDRW P.c. BOARD QTY _DESIGNATION NO. PART NO.
| cl | RI | REI 4 PIN KK-1I56 STR.CONN. 1 Jl
J2
PCMHI- PCMH4
0628-00800-0100 0062 -187B3-!XXX 06 39 - 008C 4-0002 3000 - 16367 - 0410
A639 -00024-0000 0017-00042 -0320 A080 - 90509- C000
PROJECT ENG: J.BOYDSTON USED ONKOZMIK KROOZ’ R
| PER REVISIONS
@aly | MIDWAY MFG.CO. FRANKLIN PK fLL
ASSEMBLY DWG SOLID STATE RELAY PC. A082-90509-CO0CG A084-90509-C000 DIM. TOLERANCES nsemyauiterse
Bo oe Blog 02 28°83 PART NO
MOSI - OOI114 -CoOl9
Jl an | S.S. RELAY
A.C. OUTPUT
| 3 i SIGNAL Dc.
! I
I CONTR.
Lone 4 INPUT
PROJECT ENG: J. BOYDSTON UsED ON KOZMIK KROOZ’R)
DIM. TOLERANCES Und seednies SCHEMATIC DWG concenmerry 214 — S.$. RELAY P.C, ocomac + vos A082 -90509-CcG00 move ola — ¢.002 .000f pare O2 /28/ 83 A084 -90509-C000 REVISIONS
®aly | MIDWAY MFG.CO. FRANKLIN PK. ILL
PART NO. MO51-—00114 - COl18
8-17
DESIGNATION LIST
DESIGNATION NO.
cP I cp2 cp 3 cp 4-6
amma mavanDaDDA a ' oO
vl
v2
OPTOI-3
A080 -91434-D639
8-18 DESCRIPTION
lOuf I6V AX, ELECT. -Olut 50V AX. CER.
lO mf 16V AX. ELECT. Olaf 50V AX. CER.
390 1/2W 5% CRBN FILM
| 100K | 1/4Ww " | " | |
| 20K | " | " | " |
| 3.3K | 0" | 4 | " |
| IM | " | " | " |
| 10K | " | " | " |
| 10K | " | " | " |
| 1.3K | " | " | " |
2N2222A TRANSISTOR
LM339
7407
OPTICAL SENSOR
KK-100 VERT 12 PIN
PLASTIC RIVET
P.C. BOARD R20 RI9 Ri7
+ CP3 ces _j {8s
R6
cp2 + CPI
«28h oare O 3 /O2 PROJECT ENG: JOHN BOYDSTON USED ON KOZMIK KROOZ’R
NIM. TOLERANCES ff UNLESS SPECIFIED. ASSY DRAWING SENSOR P.C.
A084 -91434-D639 DESCRIPTION
-Olwt SOV AX. CER. !Ouf 16V AX, ELECT.
3902 1/2W 5% CRBN FILM
| 13K 1/4W | a | " | |
| 3.3K | " | " | ui |
| 10K | " | ¥ | 7 |
| 20K | 7 | " | 7 |
| 100K | " | " | i |
| IM | 7 | it | " |
2N2222A TRANSISTOR
LM339
7407
OPTICAL SENSOR
KK-100 VERT 12 PIN
PLASTIC RIVET RND.HD
PC BOARD CROSS REFERENCE LIST
Q
» ty
Gaby | MIDWAY MFG. CO. FRANKLIN PK. ILL
PART NO.
MOS| DESIGNATION NO.
cP2,4-6. cPl,3.
'
17,19. 4-6, 20. 13-16 ,18. pDDDD-DD
i
Ul
ve
OPTO I-3
vl
- 00639 -DO06 PART_NO.
0639 ~-00800-0002 0639-00800-000I
0062 -150D3~IXxx 0062-185B3-1IXxXx
0062-203B3-IXXXx
0062-227B3-IXXXxX
0062 -241B3-IXXX
0062-275B3-IXXX
0062-323B3-1XxXXx
0639-00802-0001
0639-00803-0002
0639-00803-0001
0639-00804-0001
3000-16364-1201
0017-00072-0091
A080 - 91434- D639
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.