CATHODE RAY TOMES

Head On 2 Invinco

Head On 2 / Invinco (Gremlin/SEGA, 1980) · Manual · 45 pages · 17 sections · original scan

Page 1

SSHSOTOOSESE RELAY SOCEOLSOTEOSEROSS SESEOSESSSDES SESS 2648:

-0359

RS MANUAL

MANUFACTURED BY

OWNE

ANUAL PART NO

29FSELSRSLSIRE DGS D FP SSSSREEESDE GES S| C6886 9924989898086) $888 6895060420089 a trreaTreowr@gq@gew#gea&aq@qgn&kie@gonpgd aff oa ar.

Page 2

HEAD ON 2

&

INVINCO

DUAL GAME MANUAL

HEAD ON2/INVINCO OWNER'S MANUAL (C) Copyright 1980 by GREMLIN INDUSTRIES, INC. All Rights Reserved.

Page 3

INTRODUCTION

This is an electronic game that makes extensive use of digital integrated circuitry and television monitor circuitry. This manual assumes the maintenance technician possesses a general knowledge of solid state circuitry,microprocessor, TTL digital integrated circuitry and T.V. monitor concepts. Any individual NOT knowledgeable in these areas SHOULD NOT attempt repair of the electronic portion of this game. IT SHOULD BE NOTED THAT ANY ATTEMPT TO REPAIR THE GAME IN THE FIELD WITH- OUT EXPRESS CONSENT OF THE FACTORY WILL IMMEDIATELY VOID THE WARRANTY!!!

IMPORTANT NOTES:

NEVER replace any components with anything other than exact replacement parts. (See Parts List located on Service Schematics.

NEVER remove circuit boards/connections while power is on.

DO NOT replace the fuse with anything other than the proper value. A blown fuse indicates an overload condition within the game. Replacing the fuse with a higher value can cause severe damage to internal components if an overload occurs.

ALWAYS consult the manual before attempting repairs.

CORRESPONDENCE regarding this game should be addressed to:

GREMLIN INDUSTRIES, INC.

8401 Aero Drive

San Diego, California 92123

(714) 277-8700

Page 4
IMPORTANT NOTE

An important service note is posted in this game and is repeated here for emphasis:

IF AT ANY TIME THE T. V. SCREEN SHOWS A MEANINGLESS DISPLAY

OR THE GAME OTHERWISE MALFUNCTIONS, SIMPLY DROP A COIN INTO

THE COIN MECHANISM. THIS SHOULD CORRECT THE PROBLEM. IF

NOT, THE GAME REQUIRES SERVICE.

The circuitry in this game has been arranged so that the insertion of a quarter through the coin mechanism will reset the system. This clears up temporary problems caused by power line disturbances, static, etc.

SERVICE TECHNICIAN NOTE:

The system reset circuitry described above requires that the coin counter is attached to the system. If there is a coin counter problem and no replacement is available, the game will function properly if a 10K Ohm resistor is connected across the coin counter input pins to the video logic board.

Page 5

REPACKAGING INSTRUCTIONS

Should it be necessary to ship this game, follow the instructions below for game recrating:

A) If the original shipping bolts have been discarded (Ref.1), obtain four 5/16-18x1 3/4'' hex head bolts with 5/16" flat washers. Carefully lay the game on its side and attach skid (Ref.2).

B) Place game upright. Tape game keys to upper flange of operator's panel (Ref.3). Crate the game using appropriate shock-absorbent packing material (Ref.4). Include padding on all four corners of the game (Ref.5). After crating is completed, secure package with strapping (Ref.6).

NOTE: If the game is to be shipped to GREMLIN for service or repair, attach a tag identifying the distributor and indicate the service or repair to be made; include the full serial number of the game. GAME MUST BE SHIPPED PREPAID.
Page 6

HEAD ON 2-GAME CONCEPT

The most noticeable change on Gremlin's new HEAD ON 2 game, is the addition

of two turn-around lanes on either side of the screen. With these turn-around

lanes, HEAD ON 2 becomes a different game, even more challenging and exciting.

The game begins by displaying the following information on the screen:

BONUS

POINTS PER ..- POINTS PER 0%

The computer's car and the player's car start at the bottom of the screen. When

the player clears all lane markers against one computer car, he is awarded the 200 BONUS points and then is pitted against 2 computer cars. After clearing the

lane markers again, 3 computer cars appear. Finally, 4 computer cars are the

maximum amount that drive against the player. Each time a player clears all

lane markers, the BONUS POINTS value is increased, so that more bonus points are awarded for beating 2 computer cars than for beating 1. In addition, the

POINTS PER dot/diamonds values increase each time the bonus is awarded.

In HEAD ON 2, the player now has a few more lane options open to him in order to gain the most points and avoid a collision with the computer car. For example, if the player reverses his car's direction by passing through a turn-around lane,

he then becomes either the pursuer or the pursued. If he is pursued by the computer car, the player must be careful to avoid a rear-end collision. If the player is following a computer car, he must again watch for a possible rear-end collision into the computer car. The different possibilities are what makes HEAD

ON 2 an even more challenging and strategy-demanding game.

Also, each game is different from the next. While it is tempting to find a winning

pattern, the game will not necessarily respond the same way every time, Because of the varied combination of action, a working pattern for one game may not work

for the next. This feature will keep them playing game after game; and, each

time, new video excitement is there for all players.

Refer to the OPTIONS section of this manual for instructions on changing the

number of player cars.

Page 7

na aes fs | INVINCO GAME CONCEPT

INVINCO is a fast-paced Gremlin Multi-Phase game that pits the player

against a attacking force of numerous enemy warriors. The player begins with three Prime Defenders which are released one at a time behind the defense barrirer. The enemy warriors immediately

begin to advance, firing missiles as they approach. In order to destroy them the player must blast away the barrier in strategic places, exposing the columns of warriors to his own missiles. The player then proceeds to

destroy as many warriors as possible while dodging their attacking missiles. The warriors in the back rows are worth more points and each warrior in the very last row must be hit three times (becoming smaller after each hit)

before it is finally destroyed. If the player aims carefully enough, he may hit one warrior behind another. This will cause that warrior to

explode, taking nearby warriors with it. For an even higher score the player may try to hit the large bonus targets which sweep intermittantly across the backfield.

If during this time the player's Prime Defender is hit by enemy fire,

it will explode and another will take its place. This continues until all three Prime Defenders are destroyed and the game ends. If the Prime Defenders are not destroyed and the player clears the entire field of

enemy warriors, INVINCO will send out the ''Avenging Spirit,'' a large target which manuevers wildly as it fires its missiles in a last ditch effort to destroy the Prime Defender. If the player clears the field a second time, two Avengiftg:Spirits will descend; after the third clearing the player will face three. Thus the difficulty is intensified as the

player's skill increases.

Page 8

OPTIONS SELECTION INSTRUCTIONS:

Your HO2/INVINCO game is adjustable for different numbers of player cars and player firing bases. The following chart shows how to change these: (Locate the 6-position DIP switch on the logic board. This switch selects the desired number)

HEAD ON 2 #of cars desired

INVINCO # of firing bases position on DIP switch switches 1 and 2 up

switch 1 up

switches 1 and 2 down

ion of DIP switch posi switch 4 up

switch 3 up

Page 9

SPECIAL NOTE: NEW GAME BOARDS AND NEW EPROMS.

The following chart shows the two kinds of logic boards Gremlin will use in future games. These will be either a SINGLE VIC board or a DUAL VIC board. Also shown are the possible combinations of Eprom types that Gremlin will be using. The 2 Eprom types are

  • 2708 (holds 8K of memory)
  • 2716 (holds 16K of memory) Obviously, the 2716 holds twice as much information as the 2708, BUT the 2 Eproms are NOT directly compatible-- in other words, you have to replace a 2716 with another 2716, and a 2708 with another 2708. In addition, the 2716 Eprom socket is modified slightly to accept the 2716 Eprom. If it is ever necessary to replace a new Eprom, be sure to specify ''2708" or ''!2716''. These numbers are printed on the Eprom package.
Logic Board Type:Possible Eprom Types Used:Where Used:
SINGLE VIC board1) all 2708'sHEAD ON 1

(see Figure 1)* HEAD ON 2 Future games

  • 2708's and 1 2716 INVINCO (used in combination) DEEP SCAN Future games
DUAL VIC board1) all 2708'sAny dual game

(see Figure 2)* Future games

The reason for using both types is that some game programs are larger than could be contained in a set of 2708's. So, usually one 2716 provides enough additional memory space to hold a longer program.

Figures 1 and 2 show each of the two types of Gremlin logic boards. The boards in the photos are labelled for easy identification of all external connections.

Page 10

SPECIAL NOTE: POWER SUPPLY MODIFICATIONS: For DUAL VIC Logic Boards ONLY

In order to supply -5 volts to the DUAL VIC logic board, it was necessary to modify the game power supply. The modification simply adds a 7905 -5 volt regulator (Gremlin part #313-0023) to the power supply chassis; the 7905 is connected into the -12 volt line at pin 11 of the power supply output connector. PIN 17 OF THIS CONNECTOR NOW BECOMES THE -5 VOLT OUTPUT. The other pins remain the same: pin 11= -12v pin 12= +12v pin 13= 2-3 V AC signal pins 14,15,16 = GROUND pin 17= -5v pins 18,19,20= +5v Also, a 8900 ufd filter capacitor has been added to the power supply to provide better +12 volt regulation.

TRANSFORMER VOLTAGE CONVERSION INSTRUCTIONS:

To convert the game transformer to 100, 115, or 230 VAC, refer to the following chart:

*For 100 volts: Connect the voltage INPUT lines to transformer terminals 1 and 2.

*For 115 volts: Connect the voltage INPUT lines to transformer terminals 1 and 3.

*For 230 volts: Connect the voltage INPUT lines to transformer terminals 1 and 4. The fluorescent lamp line must be connected to transformer terminal 3.

ALSO, THE TV MONITOR MUST BE CONVERTED TO THE SAME VOLTAGE INPUT AS THE GAME TRANSFORMER. REFER TO THE MONITOR MANUAL IN THE GAME.

Page 11

MAINTENANCE PROCEDURES

|. Power Supply (Refer to drawing #815-0020, sheet 4)

  • Remove output connectors from power supply.
  • Make these initial tests: (GND to BLACK lead on C18, 9000 ufd capacitor) +9 VDC on POSITIVE terminal of C18 +17-19 V on C6 (4700 ufd cap.) -17-19 V on C5 (4700 ufd cap.) -12 V at output pin 11 (adjustable by trim pot R42) +12 V at output pin 12 (adjustable by trim pot R8) +5 V at output pins 18,19,20 (adjustable by trim pot R9) GND (ground, 0 V) at pins 14,15,16 2-3 V AC at pin 13 (Don't forget to change meter scale to AC) + 75 Vat pin 17
  • Check these voltages again with the logic board connected. If any are wrong, a loading condition exists in the logic board, most likely. -TanARAn TD

Il. Logic Board

The following instructions will help you trace down and find most problems associated with the logic board. The procedures are listed by the more

common kinds of problems that could arise. Read through all the steps first, then apply them one at a time. The necessary equipment are an oscilloscope | and AC/DC voltmeter.

  • NO PICTURE: TV TUBE AND FLUORESCENT LAMP ARE OFF a. Plug the game in and check to see that it is receiving 115 (230) VAC. | Measure 115 VAC at the input terminals of the game transformer. If it # is not present here, proceed to next step.

| b. Check the fuse; if it is good, proceed to next step. c. Remove the cover of the junction box in back of the game. Measure 115 VAC on the output of the line filter. If it is not present, the line | filter may be bad. Or, one of the AC line connections in the junction box may be loose. UNPLUG the game and re-check these connections.

| d. If the fluorescent lamp still does not operate, turn off game and on ~ again. This usually re-starts the lamp. If it doesn't, turn the lamp in its socket; this will re-seat it for a better connection. Sometimes | the lamp works loose during shipment. e. An ON/OFF switch for the TV monitor is located on the TV chassis, below the neck of the picture tube. Make sure it is ON.

  • NO PICTURE: TV TUBE AND FLUORESCENT LAMP ARE ON. SCREEN BLACK. a. First, make a quick check of the moni tor-to-logic board connections: | Are all wires making contact with the pin connector? Are the wires secure on the monitor plug-in connector?
Page 12

b. Check to be sure U14 is seated in its socket properly, and that no pins are bent. This IC is a Prom that develops the necessary video timing sequences. Usually if one pin on the chip is out of the circuit, the screen will appear black. Proceed to next step if this chip is seated correctly.

c. Inspect the high-voltage lead coming off the monitor's high-voltage transformer. This lead attaches directly to the TV tube. Sometimes, during shipment, this wire is jostled out of contact with the transformer. Turn off the game, and carefully push the wire down, toward the transformer, to re-seat it. Now check to see if the picture comes on. If it doesn't, proceed to step d.

d. Using a voltmeter, measure the three voltages powering the logic board. These voltages, +5,-5, +12 volts can easily be measured at the power supply-to-logic board connection. If all the voltages are present, go to next step.

e. Using an oscilloscope, test for clock signals at the following points: (For the moment, don't worry about what each signal should look like: We're concerned with finding floating signals, and/or signals that are not present when they should be, and why they are not.)The scope setting is .2v/div. @ 5usec., with a 10:1 probe. All clock signals, except the video signal, are about 5 volts in amplitude.

  • Check pin 6 of U50. Look for a 14-2 volt video signal. If not there, check pin 4 of U50. If it is here, U50 is probably bad. If the signal is not at pin 4 of U50, suspect U57 and U67.
  • Check the following IC's and pins for any floating or missing signals: U13, pin 8. U22, pin 9. UI5, pins 11,12,13,14. UI4, pins 1-7, 9. U19, pins 2,6,10,15. U20, pins 2,7,10,14,15. These chips make yp the video timing circuit. Make sure there are no floating or missing signals on any of these chips. If there are, suspect the chip is bad.

PICTURE APPEARS: COLOR IS DISTORTED; SOME COLORS MISSING

a. Check the red, blue, and green output signals on U67, pins 47,9, respectively. If no signals present, suspect U67, U49, or uéé.

INCOMPLETE PICTURE: RANDOM DISPLAY

a. Sometimes the game appears on the screen with parts of the picture showing incorrect information. For example, the "HI SCORE" listings display jumbled information, while the rest of the picture is normal. The most likely cause of this problem is one of the 8 Ram IC's U69 through U76. The quickest way to find the bad Ram is simply to replace each IC, one at a time, with knowngood Rams. Be sure not to bend any pins when replacing the IC's. Also, den't overlook the possibility that one of the Ram sockets is bad.

. RANDOM DISPLAY WHEN GAME IS TURNED ON

a. Activate the coin switch a few times to see if this clears the picture. If not, turn the game off, then on again. If the jumbled display still appears, proceed to step b.

b. Check the reset circuit on the logic board. (Refer to the schematic)

Page 13

When power is first applied to the game, a reset circuit consisting of QI, Q2, U18 and U35 is triggered on to reset the microprocessor. This reset signal forces the microprocessor to start at the beginning of the game program. If the microprocessor is not reset, it will still operate—it just won't operate on the right program instructions or data, and will continually display a jumbled pattern on the screen. So, begin by checking for a 3-4 VAC signal at pin 3 of the power supplyto-logic board connector. Follow the signal through Q1, where, at the collector, a sawtooth wave appears. Then, when power is first applied, observe pin 2 of U18 as capacitor C10 slowly charges to about 3 volts. When this level is reached, U18 is triggered to change states, causing pin 3 to go high, then low. This change is inverted by U17 and finally reaches pin 26 of the Z80. Check pin 26 of the Z80 for a low-to-high signal change. If not present, one or more of the reset circuit components is bad. If it is present, proceed to step c.

c. The following lists some probable causes of the jumbled display pattern:

  • one or more RAMs one of the Eproms, U1-8, U26-33 The microprocessor, U 16, is bad. U47 (74LS245) is bad. U51 and U52 are bad.
  • Check the 3 operating voltages, +5,-5, +12 VDC.
  • GAME DOES NOT COIN UP

a. A common problem with a game that does not coin up is that the coin switch trip wire is out of adjustment. Usually, all that is necessary is to bend the trip wire up or down, depending on whether a heavier or lighter tension is needed.

b. There may be a problem in the coin circuit on the logic board. Check U62, pins 6,8 for pulses each time the coin switch is tripped. Also, U43 and/or U62 may be bad. Suspect U45, also.

c. It is possible that one of the coin counter transistors, Q3 and Q4, is bad. Determine whether or not the counter advances each time the coin switch is tripped.

d. Don't overlook an incorrect or faulty coin switch-to-logic board connection; sometimes these wires work loose from the coin switches.

  • PLAYER CONTROLS NOT WORKING

a. Check first to be sure all control switch connections are secure. This includes checking the black wires, or ground leads.

b. If these connections are good, make sure the control panel leads are intact inside the Molext™ connector to the logic board.

c. If the controls still do not work, suspect U44 on the logic board. However, U44 could be good but might not be receiving the activating pulses from U24, pin 10 or U25, pin 12. Check these also.

  • GAME'S SOUNDS NOT HEARD
Page 14

. Check to be sure the sound board output leads are making good contact on the GAME SELECT SWITCH located on the control panel. Also, make sure the audio lead from this switch is connected to the power supply/ amplifier board properly. (Refer to the game wiring schematic)

If these connections are good, check the power supply/amplifier board for any audio signals. Specifically, check U4, Q8,09 on the amplifier board for any game sounds.

If there are none here, suspect U63 and U64 on the logic board. Also, check U23 for the pulses that turn on U63 and U64.

If these chips appear good, the sound boards are probably bad. Refer to the sound board schematics for each sound's circuit.

The following chart lists the sound type and corresponding sound board pin numbers:

HEAD ON: Sound type Sound board pin #

Crash High speed player car Car sound on High speed computer car Audio output Screech #1 Screech #2 Bonus. OUR EWH =

INV INCO: Ship hit UFO hit Laser UFO 1 Saucer UFO 2 Audio out NN ONnEWN

DEEP SCAN: Bonus sub. 1 Sonar 3 Score bonus 4 Water spray a Depth charge explosion 10 Sub explosion 11 Ship explosion 12 Audio out 15

Page 15

RECOMMENDED SPARE PARTS LIST- DUAL GAMES

Gremlin Part #:

130-0001

130-0002

200-0011

253-0104

253-0120

253-0121

253-0123

390-0011

220-0008

220-0035 220-0066

220-0071

220-0072 475-0007

510-0014

510-0042

510-0051

(800-0076)

270-0001

514-0001

240-0007

510-0023

510-0050 800-0056

240-0091 250-0289

250-0291

510-0041

315-0019

315-0050

316-0246

316-0287 Description:

speaker

speaker cover

Algol color monitor

Plexi front monitor panel

panel logo, HO2/INVINCO sd o HO2/DEEP SCAN

" = DEEP SCAN/ INV

fluorescent lamp

coin counter

coin door lock and key coin mechanism, complete

coin reject buttonéspring coin return stop (U-bolt)

volume control

slide switch

coin switch

push button switch

photo coin assy.

line filter, junction box

fuse, 2A, slo

black pushbutton control

mounting/contacts for above

game select switch

complete joystick

joystick knob

threaded rod

upper sleeve

joystick switch

2708 Eprom, blank specify by number on Eprom 2716 Eprom specify by number on Eprom

color prom INV/DS

color prom H02/INV Quantities per 10 games:

Uw wWwwWwnwwwny

set

set

Page 16

314-0001 314-0093 314-0099 314-0104 314-0105

315-0031

315-0039 315-0042

316-0206 475-0002

482-0010

482-0014

510-0043

(The following are suggested parts for all sound boards: 313-0008

314-0042 315-0006

315-0035

315-0043 481-0006

481-0008

482-0006

482-0023 313-0004

315-0005

315-0009 color prom H02/DS

color prom INVINCO

color prom DEEP SCAN

555 IC 74LS374 IC THLS245 745138 74LS253 Z80 microprocessor

RAM IC Video Interface Chip (VIC)

video timing prom resistor pack PE8050 transistor 2N4401 "'

6-position DIP switch

LM348. IC

7406 IC CMOS 4017 IC MM 5837 IC CMOS 4069 IC 1N914 diode 1N5231 Zener diode

2N4403 transistor 2N4093 "' LM741 IC cmos 4013 IC

CMOS 4081 IC NwWwwWwwu =

Page 17

PART NO PARTS |TITLE assy

LIST QTY PER ASSY DESCRIPTION REF DES

{51 -O00OS CAP CER &B0 pf SDV Ele

/S1-OO// CAP CER Olt 5OV £73,274, CH1,C42

Sd = ODA CAP CER -f pt 50v C1,2,4,5,511, |3-40,43-12

752-000! CAP FILM «left /O0V L275

JS3B-060 i CAP TANT 10 pF 28 y €3,C6,C/0

4153-0002 CAP TANT Iypf 25V Cg

153-0008 CAP TANT /OOpf ZOV ca

17O-O/174 PC BOARD

Z2/!- 0004 CONN PIN TEST PT TP! —TPG

212-000 + CONN M + PIN

2/2~O02! CONN M_/DO PIN

2/2-003! LONN M_/2@ P/N BKT 16 PIN DUAL INLN XDI4,49,69-76, XSW!

SKT #0 P/N DUAL INLN XVie, XU57

SAT 2¢ PIN DUAL INZLN XU /=XUB,XU26-X3 XTAL CLK 15.46848 MHA Yl

3/4-000! /cG NESS55 UIB, U36,U 37

314-00/5 /C 7404 UIT

314-00/2 7FLABOO 23,UGe 25,U68

Page 18

parTS |TITLE assy LIST |} DUAL GAME V.L€.

ett | QTY PER ASSY |

PART NO DESCRIPTION REF DES

Al4-0040 | /C 7#LE/Z5 US/,U52,U54,U55 StF -00 Fa /C 7F#SOF4 U13 3I4~O0 5H /C 7#LEOSG UIO-~-Wl2, 1335,U5b6

3/4-O0 59 3BI14+-O062 314-0070 3BI*F-O072 4C 7#E5175 U/7,U20 iL! FL rha7 UL7 fC F4eCS 02 U2d {GQ 7#FCS24S U47 10 74L586 uUsO 1C 7#LSI74 U53,U66

3/4+-0073 314-0076 3BI#+-0093 a 10 74#L5 374 063,064 /2 7445/38 U7,U34 4C 7425 253 UFIdt - U4 (C 74#LB/63 UIs 1E 2BO CPU Ultio 1C RAM #K D OA4SPEC 2H UGI-U76G 1/C VIDEO (NTERFAC DST 3/G- 4C PROM 32X%8 CTL 390- LED RED

Page 19

PART NO

PARTS [TITLE 4 SSY

gi oan ma LIST | QTY PER ASSY | DUAL GAME \V.1.C,

DESCRIPTION

REF DES

47/1-O/101 RES 100 OHM (7P2W5% R5

47/-O102 RES 1k OHM !4/2W5% R H-F13 19-2 4,2 1528 3990

47/1-O1034 RES /OK OHM Il/2W 5% R190, R34 "R35.

“£71 -OlOF RED 1OOK OHM I/2W 5@ A fy Re R7

47/-O018B3 RES (8K OHM |/2W5% R30, R36

471-~-O220 RES 22 OHM Il¥z2ws% "RI4-RIo

F7Tl-0O221 RES 220 OHM V2ZWS5% R33

e7i- P85) RES 330 OHM 172 W5%|R3,R4,RG6,R17,R18,R3\

4+7/-OFT71 RES 470 OHM 172 WS Ra

471-0472 RES 4.7K OHM 1/72 W5% RI, R37

4785 -000\ POT /OK CAR PCLMTYV R32

477-O002|2 RES PACK /5 X 2.2K RPI,RP2

4#B1-0001 DIODE INF¢OO2

4+Bl- 0006 O+ DIODE INV/4 AING/4AD DI,D3

$F BZ-OOlOl|l XSTR PE BOSO @ 3

+B2-00/4 XSTR 2N4¢40! 41,02, 04, 95

510 -0043| 1 SW/ITLH GPOS DIP SWI

152-0007 {2 CAP FILM .00l,pF 250V C76,C77

Page 20

TITLE

HEAD ON SOUN

DWG NO OF & | REV

APPR

[RAFT | CHEGK | AppR | woe | vin Ke | of | YT ce PER ECN 308 ) se [RS TB. |

/LTR] DATE = \- 8774 1-75-79] ECN 273 ADDENDUM 273 2-12-79

Page 21

ti PART NO QTY PER ASSY PARTS | TITLE LIST DESCRIPTION REF DES

PF 51“OOI| CAP CER 20) uF 50vV £8 4/3,!7, 82,21, 22

y EV=DO12 CAP CER o/ pf SOV C5,C12,C 20,627,035

#5Z-0001 CAP FILM ol ut 100V £37C20,025 “4

Hx2='00 12 CAP FILM O47 pF 2ZO0OV CZ, 023,024

52-0018 CAP FILM 01 pf 250V C3,C@,019

I5Z2=OO2Z0 2.1, CIB, Clb

1A}9) 00) a} S P33a-O001 CAP FILM 47 yt /00V CAPTANT /0 pt 25V C10, C11,C2 8-2 30,C33C349

153-0002 £4,069

IN 133-000 3 CAP TANT /yf 25V CAP TANT B.2 pf2 5V CIF, /5

r5 23-0004 CAP TANT 4.7 pf 25V

SE COGSGoGGGamS LTO -0O154 PZB HEAD ON 50UND

212-003! CONN M /2 PIN Pl

313-0004 /C LM714I EN DIP U3

313 -O008 12 LM34¢8 DIP Ul

314-0001 !C NESS5 DIP U2,04,U9,012 ,UI4

BLS =0005 /C 40/3 U5-UB

BLS 5 OOO 9 12 4081 Ull

alb= 0035 1C MM 5837 ul2

ents = 0043 ic 40649 UIO

Page 22

PART NO

TITLE

Gremlin Industries, PARTS Sam Biage, Eaiiternia LIST [QTY PER ASSY | [QTY FER ASSY |

HEAD ON SOUN

DESCRIPTION

REF DES

F7l-Ol10Ol 100 OHM "Y2W 5% RZ23,R32

471-O1O? | K OHM I/2W 5% P4,R5,RB,R14,R22,R35, R45,R55,R72Z, R48

47/1-O1038 /OK OHM 172 W 54%) RIO,RIZ,R13,R 25, R43,R46,R50,R50-RLO Rlo4,RG7,ROBR15

47/-Ol1lO4F 100K OHM //2W5% R15 —RZ1,R24,R 34,238 R41,R42,R 62,RG65,ROF R1I,R 16

47/-O1O5 1 MEG OHM /72WS5% R3,RIO.R17

471-O!l24+ 120K OHM '2W5% R47, R51,RG3,RGG

47/-O\53 RED 15 K OHM !/2W5& RI,R2

F7/- O1S4 RES 150K OHM |/2W 5% R39

471-0220 RES 22 OHM !/2 W5% R49

471-0224 RES 220K OHM |I/2W5% R40

4¢7/-O394 RES 390 K OHM I/2W 5% R2C~R31,R4+4,R873

47/-O472 RES 4.7K OHM I/2W 5% R3B6,R52,R714

4¢7I~OFT73 RES 47K OHM 1/2W 5% R33.

471-0474 RES 470k OHM ive W St R9,RII

4+7/-O0682 RED f R53,R54

od +] ]~[—|=]a] aj ~] a] y POT, RG,RT

©

DIODE

ING/4/ IN 4148 oOi-Ds

FORM NO. 001-1501

Page 23

SS —_ a Se ene ese BE FE SE SF SS Be SE FS Ss S =

PARTS | TITLE

LIST

E | QTY PER ASSY |

DESCRIPTION REF DES

47/- 0723|/ RES 22K OHM aw 5% RI7

Page 24

i= =

MONITOR @ [ae falsfeyny—

# BAl-DOIe

DUAL GA LOGIC BO

< | wanes 231-0007

  • B|9)2

GAME POWER SUPP LY

is

25 || 27) 28)

Page 25

REVISIONS Pla DESCITON one RELERGED. acs

COIN MECH. #2

MARNE SS t 807-0010 © © Sly @) } HARNESS # 200-070 INVINCO. SOUND BOARD

wen ub

= Lane ware OPTIONAL GAME SELECT SwiTe

731-0026

ROMENCLATURE OR DESCRIPTION PARTS UST Gremlin industries, ine. flan Biage, Catitorne 923

DO_NOT SCALE DRAWING WIRING DIAGRAM

HEAD ON 7 / INVINCO

A

sneer 5 OF 5

Page 26

B.Z VRM & o£ oz t@.5 VRM Sis ov

SHIELD o—)

560-0003 .

NOT ON P.C. BOARD

D/O D3 Dig, Ds IN523! MRO! | MR5O![MRSo

HIZV Le 10pF 25v R2u 27K C/T /0pF

R20 IK

aay +] /DOnF z5V

Ci4 + Oly Sov

APPLICATION:

Page 27

REVISIONS ZONE LR DESCRIPTION A | RELEASED BI PER ECN 327

| Qe Tip |

so] eer | NOMENCLATURE OR DESCRIPTION

HERWISE SPECIFIED S ARE IN INCHES SARE DECIMALS ANGLES. xX = = x = PARTS LIST Gromiin industries, Inc, San Biags, Cobiormin 92023

DUAL SCHEMATIC ——

POWER SUPPLY

GAMES

ALE DRAWING ‘CODE IDENT NO. [DRAWING NO. 800-DO072 a

N

S S Q

Page 28

Lyin HER Mey STORE TO BE MOUNTED WITH Lit PLETE £ IMSULAT NG HARDWARE "BE Awe FZ2 5A

LESS UTHERWISE SHECIFIED

Page 29

ce-o9 A\ REF ONLY

TM 1X18) 2)(2) / (a) (a) &

  • (4) PCB REF UNLY DATE

TRANSFORMER

WIRING DIAGRAM

SEE (DETACHED FARTS 2/ST A|RELEASED wie Birr ron W ain 12-3-79 Vy 89]

reRN

new

Pint MOLEX COUN

PARTS LIST Nowra ~ oseetns _ =

Tactes OIneRW SPrCTINO IMRENSIONS ARE INCAS TOLERANCES ARE FRACTIONS DECALS ANGLES.

wus Gremlin industries, inc.

ASS ¥ POWER SUPPLY

DUAL GAMES

TE [COOL WERT FS [SRAWING WO Ray D BOC “77? | B t

Page 30

Do

Ds

D4

D3 yz lo |7

ves BIS-0039

315-0037

v7 315-0039

ur 315-0039

“73 315-0039

s74 BIS- 0039

u7s BIS ~0037 +

i

a

1? lo BIS -0039

cs Ve if 3 +5y it

Page 31

REVISIONS: Zone | UR ‘DESCRIPTION ‘ATE

AEyesWIE [19-17-79 Be
PreePERF 4 350vB [ro 23-75]
vesPER8 [ae 79)
TOMPaL424y 422 fo

TIMER wars Te. [hee 741504 ot *e D

#30 pp 18K 741800 ree 791574 eal H FXT BLK wR—2| -~3V @

5 2] 8 VSG * R 5 zys]? papzys

74.508 DIDa). bow4

5a] 740574 = == EaES UAL

piifa774a5
+401asetcsrs7pisVibE

Ng 4 |? PRao comp vin} C

J Sto SYNC

2vsyne "827Caitca5GD} +sv

741508

i5z10le
USB ® 74L51744TTsa fio uss

M1 Vv BUT 3 70 74L 808 CoMPSY

RIReRsR4—p R34vineo
R2RIep
  • oe | r
ustustustus4ussussussuss
329125129
:177415125
‘bfy8Bulo5in3

rai Sizs VIDRD

D7DGbsD+D3D2oOog
ke) aePART ORNOMENCLATURE

90] ent | weNTirnNG no. OR DESCRIPTION. PARTS LST Grumiin industries, ie. Son Grow Eativormin ORE DCHEMATIC

DUAL GAME V.1.C.

‘SIZE [CODE IDENT RO [ORAWTING FO. Riv 30f-D058& EXT ASST USED On "APPLICATION. (DO NOT SCALE DRAWING SCALE NONE

Page 32

PETE

F = Jo |S

a tw |r

un

2|s

vfs

273Z

32 K ROM zI SOCKETS USED JUMPERS

sv ALL EI-EZ, £8-1 EN-€i Pays EEW ETO ae a UB Gou4ue U33,034025,027, *5Y lunbu, Uae EI-ES,E5 Eu-EI2. An | u33,U29, UB, U4 EI-E3E5-El4) GND|v33,u29, uB,U4+ E1-ESES-EI4,

Page 33

7HLSI25 si

Penn fing SCHEMATIC —— pean TE lay | NNUAL GAME VIL. “EE [EOE WENT 0, ORAWTNG RO £3, ENE! D| BIO-0O 4A

Page 34

BAL MZ MA VCAS VRAS WH pa LS SHT &

YI 15.46848 MHZ

C12 esos 74204 74504 nope

nad

(404 7404

D4 $x In9002% 10K

2,132 cza-2A, Fp pie30-40RRi2 SPI [ex 30-40, SAO ne Sar

rant REF COIN SWITCH

Page 35

2 | 1 REVISIONS TORE UTR DESCRIFTION DATE ALF te. to

QQQHOO 09

DAT 2

ZomP BL

TIMER

Com FF

7 NOMENCLATURE _ OR’DESCRIPTION PARTS LST ax] Se PART OF po | ent | IDENTIFYING No

forarss orrtnwse SPrCTED cron ane OH CHES TouERanct San Bioge, Catitornss 9223

DIAL GAME V1.

AIT HNO SBC

7 [eer a oF I r is TERT WO [DRAWING WO eev DO_NOT SCALE DRAWING

Page 36

INVADER

LASER SHOT 4SV t5ue5Y +5

74L3107

INVADER, arr fa]

SAUCER| c3a RBI {t AAA 10pf 100K +12

RIz0 100.0.

ans [eo 741504

Page 37

REVISIONS [aoe [ore BescmrTION Filia t

7#1800

cz aotpt se jopf Rss. ]* TT raNr 5K = = ey ae +IZV i INVADER BOUND

ine sov

Rios. SK INVADER HIT SoUND

RIBS Lmag20 i R30) SK SAUCER SOUND

Page 38

+5V +5V +5v

Seow 3900

cs tet aur

Page 39

LM3900

SBCHEMT/< — INVINCA 2°! ND

Page 40

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 41

‘DRIMYUC_JTVOS JON_OG ‘aa GNNOS NO GvV3SH DIANW 3H OS ee SmeeED “Borg Ses DE BOpURSMPe WHOL Ip h2SzUI8

Page 42

2 PLAYER Zam) SS

SDUND IN-HEAD ON 2.

eeuect OPTIONDL GAME SELECT <wiiTC HEAD ON Z

Page 43

4 3 | 2 1 ef DESCRIPTION

JUD, WIRE HOLD DOWN) hs. 200-0004 d ——BRN— PIN 1 RED}

P66. HARNESS CONTROL PANEL 231-0010

pen'Y, CONTROL VANEL

  • 000. EXTRA GROUND FOR OPTIONAL CONTROL

So] awe PART OF NOMENCLATURE rao | toewr_| IDENTIFYING No. OR DESCRIPTION PARTS LIST ORLESS oTrennSe SPECIFIED DIMENSIONS. ARE-IN INCHES TOLERANCES AF Gremlin industries, Inc. a San Biege, cakitorven 9223 werent SS" CONTROL PANEL A

ae COMPLETE HEAD ON 2 7 INVINCO

D AS-COOB A

a Sa Be an Tie]

2 1

Page 44

HEAD ON SOUND INVINE

HARNESS 32-0007

cow MECH

DUAL GAME Vl. Ce

DEGAUSSING coe HARNESS 832-0003

DEGAUSS ING SWITCH

HARNESS BS -0000

Page 45

Z PLAYER

Q] attach To eRAcKeT BolT NOTES: l paver #1 .

1 iesj|

1} ey | \|rse1 es | & A fine

|s,Ia

‘ee ae —s EY 831-0017 = LTA Lea 32-0004 [a3 labs rm Cs

[23 cas 8 aig HARNESS Leg} 32-0005) eal | x = ine == a) = ae

uzPLAYER *ZmS
bal|©6]g
|ieNy
Ess 852-0015Oe) aci [reereh

ee a)

il|reins

| L

| SOLATION TRANA FORMER a aEv 732-0001 = JA = el ocr int ys aiialaahe 735 cet ee aaa Crt KTAIL