Boxing Bugs
Boxing Bugs (Cinematronics, 1981) · Manual · 99 pages · 52 sections · original scan
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
BOXING BUGS
GAME MANUAL
TABLE OF CONTENTS
FCC WARNING... . 2... 2 eee ee ee ee ee
PURPOSE AND LIMITATIONS ..........2.2..
WARRANTY. 2. 2. 6 6 ee ee ee ee ee
CUSTOMER SERVICE PROCEDURES ...........
PART ONE
BOXING BUGS - THE GAME. ...........048
RECEIVING AND INSTALLING BOXING BUGS. ......
OPTION SWITCHES DIAGRAM. ..........
GENERAL INFORMATION AND PERIODIC MAINTENANCE. . .
OPERATOR'S GUIDE TO TROUBLESHOOTING .......
PART TWO
VECTORY THEORY. . .. 2... 2 ee eee ee ee
THEORY OF OPERATION AND TROUBLESHOOTING HINTS . .
TROUBLESHOOTING GUIDE AND BENCH SET-UP. .....
SUGGESTED PARTS FOR STOCK. ...........
BOXING BUGS PARTS LIST. ..... 27. 2... we
APPENDIX A
ASSEMBLY DRAWINGS, SCHEMATICS AND WIRING DIAGRAMS PAGE
ii
dii
iv
8-1
9-1
CINEMATRONICS, INC. BOXING BUGS
This equipment generates, uses, and can radiate radio frequency energy; and, if not installed and used in accordance with the Instruction's Manual, may cause interference to radio communication. As temporarily permitted by regulation, it has not been tested for compliance pursuant to Subpart J of Part 15 of FCC rules, which is designed to provide reasonable protection against such interference. Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures may be required to correct the interference.
PURPOSE AND LIMITATIONS OF THIS MANUAL
This Manual has two major purposes, and is correspondingly separated into two major parts.
Part One of the Manual contains information operators need to know. It has been written to tell people who have little or notechnical knowledge what they should know about this game, without getting technical.
Part Two of this Manual is designed to help the qualified technician understand the functions of the various circuits
in the game, At press time, all available information was included in this Manual. If you need further assistance,
please call Cinematronics' Customer Service Department at the toll-free number.
THIS MANUAL DOES NOT REPLACE TECHNICAL EXPERTISE. SHOULD
OUT-OF-WARRANTY REPAIR BE NECESSARY, WE SUGGEST THE OPERATOR
PROTECT HIS/HER INVESTMENT BY HIRING AN EXPERIENCED, COMPETENT TECHNICIAN (PREFERABLY WITH SOME KNOWLEDGE OF THE VECTORBEAM
TM* MONITOR). WE HAVE SEEN MANY EXAMPLES COME INTO THE FACTORY
OF INCOMPETENT REPAIR CREATING MANY MORE PROBLEMS THAN
ORIGINALLY EXISTED. ONE COMMON FAULT IS INCORRECT SUBSTITUTION
OF PARTS. ANOTHER IS DAMAGED FOIL TRACES ON PC BOARDS.
REPAIRING BROKEN FOIL IS TIME CONSUMING AND THEREFORE COSTLY.
ii
WARRANTY
Cinematronics, Inc. warrants the goods to be free from defects in material and workmanship under normal use and service for a period of ninety (90) days from the date of shipment from factory. Cinematronics makes no representation or warranties concerning the goods whether express or implied by operation of law or otherwise, including those of merchantability or fitness for any particular purpose, or with respect of patent infringement, except as may be specifically made herein. Cinematronics limits its warranty obligations herein to the repair or replacement of such parts which have been returned to Cinematronics' plant at purchaser's expense and which examination shall disclose Cinematronics' satisfaction to
have been so defective and to the shipment of such repaired or replacement parts to the purchaser F.0O.B. the shipping ‘ point.
This warranty does not apply to any Cinematronics' product which has been altered or repaired by unauthorized personnel or service facilities or any products which have had the unit serial number altered or removed.
Upon acceptance of the goods, the purchaser agrees to assume all liability for damages and/or bodily injury by the purchaser or any other person and to hold Cinematronics, Inc. harmless from liability or claims arising from the use of the goods by any person. Purchaser further agrees to indemnify Cinematronics, Inc. from any liability, claim, cause of action or litigation resulting from the use or misuse of the goods by any person.
Parts returned for warranty service must be packaged so that no damage is incurred during the shipment. Full documentation and instructions must accompany returned parts. Parts must ‘be shipped prepaid to: Cinematronics, Inc. ‘ 1841 Friendship Drive El Cajon, CA 92020
iii
CUSTOMER SERVICE PROCEDURES
FOR AUTHORIZED CINEMATRONICS' DISTRIBUTORS
It is the desire of Cinematronics, Inc. to provide efficient and courteous service should the need arise. We
have a fully staffed Customer Service Department and encourage you to call our toll-free number: (800) 854-2666 for technical assistance between the hours of 8:00 A.M. and 5:00 P.M., California time, Monday through Friday.
In order to provide the very best service possible, the following procedure for ordering or returning parts must be followed:
- All equipment ordered from Customer Service, whether in or out of Warranty, must be placed with a Distributor's purchase order, either by mail or verbally by telephone.
- Advance replacement items may be obtained only during the term of the Warranty and when such items are available, using the same procedure as when ordering parts. When ordering a PCB, please include with your order the game serial number and the number of the PCB you wish replaced.
- All items received as advance replacements will, after a period of thirty (30) days, become the property of the Distributor, with applicable charges applied in the event Customer Service has not received the defective item against which the advance replacement was made.
- The Distributor must call this facility for an RMA number prior to returning any item. Please be prepared to provide us with the game serial number and the PCB number when requesting an RMA.
- In all situations covered above, and in all other situations, the Warranty offered by Cinematronics, Inc. is applicable and should be fully understood.
- Parts returned for service must be packaged so that no damage is incurred during the shipment. Cartons without a prominently displayed RMA number will not be accepted. Full
iv
documentation including game serial number, PCB number on outside of package, and reason for return must accompany parts. Ship prepared to: Cinematronics, Inc. Customer Service Department 1841 Friendship Drive El Cajon, CA 92020
(800) 854-2666 (714) 562-7000
PART ONE
Information for Operators
SECTION 1
BOXING BUGS
GAME LAYOUT
In the center of the screen is a player-controlled rotating cannon, enclosed within an octagon. The cannon shoots fireballs from one end and has a boxing glove on an extension arm on the other end. The octagon is a protective wall for the cannon. Fireballs and the boxing glove pass over the wall to targets outside.
Bombs are randomly located outside the wall. Each bomb has a lite fuse. Three bugs are also randomly scattered outside the wall. The player's score, the number of cannons remaining, and the number of bugs that must be knocked out to complete the round are shown at the top of the screen.
GAME PLAY
Play begins with the three bugs outside the protective wall trying to maneuver bombs against the protective wall. After a bomb has been positioned against the wall, the bug scurries to fetch another bomb.
The player uses the cannon to shoot the bombs and bugs with fireballs or punch the bugs with the glove. The cannon is aimed by rotating it to the proper position.
If a bomb is struck by a fireball, it begins sliding away from the point of impact. The direction it moves is determined by the angle of impact, just as in shooting pool. The player can control the motion of the bombs in this manner. The boxing glove will pass over all bombs.
When a bug is struck by a fireball, it slides away just like a bomb. Bugs hit by the boxing glove are instantly knocked out.
As play progresses, the fuses on the bombs burn down and the bombs begin to explode. If a bug is next to an exploding bomb, that bug is killed. If the bomb explodes while it is next to the protective wall, a segment of the wall is destroyed. If a bomb explodes next to the cannon, the cannon is destroyed.
Bombs that explode are instantly replaced by new bombs which appear randomly on the screen. Every time a bug is killed, a new bug will randomly appear from the edge of the screen as a replacement, unless the maximum number of bugs for that round has been reached.
After a pre-determined amount of time or one wall segment is destroyed, a’ flying bug moving at the same speed as the other bugs will appear. The flying bug moves randomly around the outside of the wall. This bug then stops and faces the cannon. The flying bug will either form a head or will lay an egg. If the head is formed, the head punches at the cannon. The head will destroy a wall segment if it strikes one and then recoils. After a brief moment, the head strikes out again and punches the cannon. This results in the destruction of the cannon. If no wall segment stops the initial punch of the flying bug, the cannon will be destroyed on the first punch. If an egg is laid, it hatches into either a red or lavender baby flying bug. The red bug immediately rushes at the cannon and will destroy either a wall segment or the cannon, depending upon which it encounters first. The lavender flying bug will randomly fly around the wall. As it does so, it swoops in and destroys a single wall segment at a time, until no wall segments are left. Fireballs have no effect on a flying bug. If a flying bug is punched with the boxing glove, the bug is knocked out and slowly drifts off the screen while stars whirl around its head. Flying bugs can be punched more than once for additional points.
A round ends when all of the bugs are destroyed. Each successive round becomes more difficult as the speed of the bugs increase and the burn time of the bomb fuses shorten. The game has six levels of difficulty.
If a player can fight through round three, a bonus round is awarded. During this round, two corner boxes in opposite corners appear. Each corner box has two doors which randomly open and close. During the bonus round, the cannon does not have a protective wall. The object of the bonus round is to maneuver bombs using the fireballs into the corner boxes. The corner boxes contain sleeping bugs which periodically wake up and scurry to the other corner box. The sleeping bugs killed by the bombs score bonus points. Fireballs and the boxing glove cannot penetrate the walls of the corner boxes. A player has thirty seconds to kill as many sleeping bugs as possible. After this bonus round, every fourth round is a bonus round.
Once a cannon is destroyed, play resumes at the point of destruction. The game ends when 4ll the player's cannons are destroyed.
During a game, a player can panic three times. This is done by pressing the panic button. Once the panic button is pressed, all bombs and bugs on the screen are knocked away from the cannon. If a flying bug is on the screen, it is immediately frozen in its position for a few moments. Because there is only a limited number of times a player can panic and no more are awarded during a game, these must be used with discretion.
SCORING AND BONUSES
Each bug knocked out with the glove scores 200 points; each flying bug scores 400 points per punch. Bugs or bombs struck by fireballs score 20 points. Bugs blown up by bombs do not score any points. In addition to the above, during a bonus round, sleeping bugs that are blown up score 3000 points each.
GAME FEATURES
- Two and only two bonus cannons can be earned during the game. These are awarded at 50,000 points and 100,000 points, operator adjustable to 30,000 and 80,000.
- The number of cannons per player, operator adjustable to three or five.
- A high score list with player initials is featured.
- Players can achieve different boxing weight classes based upon points scored. (Sparring partner, bantam weight, feather weight, light weight, welter weight, middle weight, and heavy weight.)
- A complete diagnostic, including total play time, number of games played, number of bonus cannons awarded, and number of bonus rounds achieved. The diagnostic can be easily accessed by a switch located inside the coin door.
- There are five different types of bugs that are featured.
- The game uses a Wells-Gardner color X-Y monitor.
- There are six levels of difficulty and an unlimited number of rounds.
10.
ll.
12. Status messages between rounds lets players know how many bugs must be fought to complete a round, how many more times the panic button can be used, and when a new weight class has been achieved.
At the end of each bonus round, the number of sleeping bugs killed and bonus points awarded is displayed.
Operator adjustable coinage values.
A rapid fire for the fireballs is activated by holding down the fire button.
SECTION 2
RECEIVING AND INSTALLING
BOXING BUGS
RECEIVING INSPECTION
Your game was shipped in ready-to-play condition. However, after removal of the shipping carton, a brief visual examination is suggested.
‘Naturally, you will want to make note of any physical damage to the game cabinet and its external components for freight claim purposes. Considering the quality of the shipping carton, any damage to the exterior would indicate possible interior damage as well.
The interior of the game should also undergo a brief examination for: loose mounting hardware (check to be sure that the major components are still securely mounted); disconnected or loose wires, cables or harnesses; electronic devices loose in their sockets; etc.
At this time the game serial number should be logged. Remember that the game serial number will be required if you need service from your distributor. Please complete the postage-free reply card and mail immediately.
ELECTRICAL REQUIREMENTS
Unless specified otherwise, your game was shipped to operate at 115 VAC, 50/60 Hz. :
A good earth ground is essential for the proper operation of this game or for that matter, any electronic device. Problems with instability and erratic operation of computer-type devices can usually be traced to an ineffective ground system. Therefore, plug the game into a properly wired three prong outlet. If a three prong to a two prong AC adaptor must be used, an alternate method of grounding the third prong must be used. t
INITIAL ADJUSTMENTS
The audio level (volume) can be easily adjusted and THIS IS ACHIEVED BY ROTATION OF THE VOLUME POT LOCATED ON THE COIN DOOR. The audio level should compete with other machines "on the floor" to maximize play time.
Display brightness is another easy adjustment. Keep the brightness at the correct level for appeal.
OPERATOR OPTIONS
The option switches allow you to select how many cannons per game, how many coins per credit, and a test pattern for the Vectorbeam monitor. The option switch is located on the logic board. See the logic option switch diagram for switch settings.
BOXING BUGS OPTION SWITCHES
LOCATED ON LOGIC BOARD AT POSITION E=2
CREDITS PER COIN SEE TABLE ONE
CANNONS PER GAME OFF 73
OFF = 50K BONUS LeveL Off = 30K
SOUND IN ATTRACT MODE FREE PLAY
DIAGNOSTIC MODE
TABLE | SWITCH | SWITCH a 4 1 2 OIN
2-3
SECTION 3
GENERAL INFORMATION AND PERIODIC MAINTENANCE
Your Cinematronics' game is designed much the same as conventional video games. The major exception is the use of an alternate means of visual display . . . the Vectorbeam monitoring system. Otherwise, the game is built of the same basic building blocks as any other video game.
POWER SUPPLY
The power supply provides all the necessary voltages for the monitor, circuit boards and fluorescent lamp. As you look into the back of the cabinet, it is located on the lower left side of the cabinet. The power supply has two circuit breakers, and a three ampere slo-blo fuse. If one circuit breaker trips, the other breaker will soon follow. Always unplug the game before replacing the fuse or resetting the circuit breakers. If you need to replace the fuse, use only a three amp slo-blo fuse. The power supply also has a line voltage select switch that must be set to match the voltage in your area. There is also an adjustment for the +5 volt section. DO NOT ADJUST unless you use a volt meter and follow the procedure in Section
- If needed, this power supply is directly interchangeable with the power supplies used in previous Cinematronics' games.
CPU _AND 32K BOARDS
The Central Processing Unit (CPU) is the "brain" of the game. As you look into the back of the cabinet, it is the large PC (printed circuit) board on the right side. It "senses" when a coin is dropped in the coin slot, operates the coin meter, and gives credit. It then "reads" what is happening at the operator controls, interprets and computes to make the game play according to what buttons the player pushes. It tells the monitor what to draw on the screen, and it tells the audio board when to make the appropriate sound effect. The CPU has a red LED (light-emitting diode), near the Molex power plug. This LED normally flashes once when power is turned on, then stays off. More on this in Section 6. Mounted piggyback fashion on top of the CPU board is the 32K memory board. This merely increases the cerebral capacity of the CPU board.
AUDIO BOARD
The audio board generates all the sound effects for the game and powers the loudspeaker. As you look in the back of the cabinet, it is the smaller PC board on the right side, just above the CPU.
COLOR INTERFACE BOARD
The color interface board takes the output of the CPU board and sends X, Y coordinate information along with red, green and blue data to the color monitor. NOTE: OUR COLOR INTERFACE BOARD IS SIMILAR TO THOSE IN OTHER VIDEO GAMES THAT YOU HAVE SEEN. HOWEVER, WE SUGGEST YOU SPEND SOME TIME FAMILIARIZING YOURSELF WITH THE SCHEMATIC AND THEORY OF OPERATION OF THIS BOARD.
COLOR MONITOR
The monitor draws pictures on the picture tube screen according to the instructions it receives from the color interface board. If it does not receive correct data, it will pop the circuit breakers.
The monitor is a completely different system from the standard raster-type monitor. Two advantages to this monitor are:
- circuitry is simplified, and
- ability to draw fine detail in the picture far surpasses conventional monitors, adding interest to the game.
If your monitor should need repair in the future, the technician should be familiar with the monitor, because it is so different from the conventional raster system.
HARNESS AND CABLES
Interconnecting cables are of two types: The Main Wiring Harness and the Ribbon Connectors.
The Main Wiring Harness carries power from the power supply to the various units of the game. It connects to each unit through the Molex plugs. The Molex plugs are built so they can only plug in the right way. NEVER CONNECT OR DISCONNECT THE MOLEX POWER PLUGS UNLESS THE GAME IS UNPLUGGED.
The Ribbon Connectors carry data to and from the CPU. Since they can plug in two different ways, care should be taken to plug them in correctly.
3-2
SECTION 4
OPERATOR'S GUIDE TO TROUBLESHOOTING
- CHECKING THE LED:
Whenever there is a problem with the game, a good place to check first is the LED (light-ermitting diode) on the CPU board near the Molex power plug. This LED indicates whether most of the CPU circuit is working. When everything works right, here is what happens: Power to the game is turned on, the LED flashes on, then stays off. If the LED is flickering or on continuously, there is a problem with the CPU, the +5 volt supply or the 32K memory board. Check +5 volts on the logic board (follow procedures in this section). If the +5 is okay, have CPU repaired.
- CHECKING THE +5 VOLT SUPPLY:
To check the +5 volts, you need a voltmeter. Turn power on in the game. Notice on the upper corner of the logic board nearest you is a little pin marked gnd. This is a great place to put the negative probe of the voltmeter. Near this pin in position T13 (see CPU layout, in appendix) is a 20 pin IC marked 74LS377. Ignore the other numbers on this chip. We can measure the +5 volt supply at pin 20. Pin 20 is the bottom pin on the far side of the chip. Put your positive probe there, without touching any other pins, and you should get a reading. Anything between +4.8 volts and +5.1 volts is okay, otherwise, adjust the voltage.
The adjustment is located on the power supply and it is the only screwdriver adjustment on the power supply. Adjust slowly WHILE READING THE VOLTAGE. Too much voltage will destroy IC's fast. If voltage cannot be adjusted into the correct range (+4.8 - +5.1 volts), repair power supply.
- FUSES ON THE AUDIO BOARD:
The audio board has two fuses mounted on it. Next to each fuse isanLED. These LED's are normally lit. If an LED is not lit, the corresponding fuse is bad. If either of these two fuses is bad, the power amp section on the audio board is probably defective.
- TRIPPED CIRCUIT BREAKERS:
The flow diagram on the following page will help you isolate problems that are associated with tripped circuit breakers.
The following Flow Diagram will help you isolate problems that are associated with tripped circuit breakers:
Power Off
Unplug 15 Pin Molex Connector on Color Interface Board
Reset Breakers
On
Breakers Trip?
Color Interface Board is Defective
See Color Interface
Wire Harness or Power Supply is defective
Check Wire Harnsee fo See Audio Bd . Section
PART TWO
Information for Technicians
SECTION 5
VECTOR THEORY
In order to understand the basic concept behind a vector generated display, it is important to have a basic knowledge of vector theory.
In the vector display system, there are no horizontal and vertical lines (no sweep) or sync. A line generated using a vector system is shown in Figure 5-1.
A line is drawn by programming a beginning and ending point of the line to be drawn, and forcing the cathode beam to travel between these two points, illuminating the entire path on the screen of the CRT. The angle of the line, the position of the line, and the length of the line are determined simultaneously, and simply, by selecting the proper voltage levels for the beginning and ending points of the line.
This is accomplished by the two twelve-bit codes (words) applied to the DAC-80's on the display board. The DAC-80 will produce a different voltage level at its output for each possible combination of input bits (of which there are 4096 possibilities for a 12-bit word).
It is also important to remember the function of the LF 13331 analog switch and its output RC network. Because we are dealing with reactive components in C101 and C201 on the display board, the charging voltages found are non-linear by nature. (See Figure 5-2.)
Therefore, when a line appears on the CRT, it is actually only part of the entire path taken between the beginning and ending points of the vector (C-D). The section of A-B is chosen as the most linear portion of the charge curve, and is illuminated.
Sections C-A and B-D are blanked at the cathode and section A-B illuminated by controlling the 74LS374's on the color interface board. These calculations are all performed on the CPU logic board.
Voltage —————_—_—> a a Y | tt | NG@n
Figure 5-2. Non-linear Charging Voltages
When a line appears on the CRT, it is actually only part (section A-B), of the entire path taken between the beginning and ending points of the vector (section C-D). Section A-B is chosen as the most linear portion of the charge curve, and illuminated.
SECTION 6
THEORY OF OPERATION
GENERAL DESCRIPTION
This section describes the principles of operation of the major circuit functions of the Cinematronics Video Game. The system's general functional description includes trouble shooting techniques and is followed by detailed circuit schematics which are included as Appendix A. The schematics used in this manual are similar in nature to those used by most industrial electronic firms.
WELLS-GARDNER COLOR MONITOR
The Wells-Gardner displays vectors (lines) generated from X-Y coordinates originated from the logic board and processed through the Color Interface Board. The horizontal points are X (width) and the vertical points are Y (height).
Some basic checks of the Well-Gardner monitor are included in the Trouble Shooting (Section 7) portion of this manual. Further information for technical description or repair of the monitor may be obtained from Wells-Gardner directly or by calling the Cinematronics Customer Service Group.
AUDIO BOARD
CIRCUIT DESCRIPTION AND TROUBLESHOOTING GUIDE
GENERAL INFORMATION
The following section describes the theory of operation for the Boxing Bugs audio board. The last part of this section contains block diagrams of the audio board. The theory of operation of each block will be described along with test techniques to enable effective troubleshooting.
DEFINITIONS
TTL (Transistor - Transistor Logic) compatible levels are defined as follows:
1 A TTL "low" or logic O is any voltage less than 0.8 volts.
2 A TTL "high" or logic 1 is any voltage less greater +2.4 volts. vcO: Voltage Controlled Oscillator CCA: Current Controlled Amplifier U: Integrated Circuit (chip)
NOTATION
A particular pin of an IC (Integrated Circuit) is denoted in the text by first the chip designation and then the pin number: e.g. U25-10 means pin 10 of 025.
Jumper patches Wl thru W12 are sections of traces on the audio board designed to be severed in order to isolate a section of circuitry for test purposes. Be sure to sever between the two eyelets, one round and the other square. The orientation of these pads is the same on the board as on the schematic diagram. Repair by adding a short jumper wire into the holes provided.
DO NOT repair any trace by adding a blob of solder at the sever. This will cause intermittent operation.
TEST PROCEDURE (refer to Sheet 6 of the Schematics)
To verify proper operation of U30,U40 and US50 disconnect the 16-pin ribbon cable at J2 and decrease the volume. Check 030-2, 4 and 6, U40-8, 10 and 12 with a logic probe, scope, or meter. They should read high or 2.4vde - 5vde (Logic 1).
Check for proper signal shaping as follows:
1 Wave form at U50-3.9, 11 and 13 should be normal square wave __ J Ls. 2 Wave form at 030-9, 11 and 13 should have longer leading edge _ “Ls
3 Wave form at U30-2, 4 and 6 should have shorter time duration and slightly lower amplitudes. = MTs circuit is designed to filter out signal glitches but allow proper input signals to pass. Next, with a test lead, ground U50-9. U50-2 should now measure low or 0 to 4 vde. Follow this procedure for the other six pairs of Schmitt-Trigger circuits.
To verify proper operation of U49 and U39, Load all lows into their output ports by tying U50-1 to ground. Using another test lead connected to ground tap, U50-13 twenty times. Outputs QA-QH on both IC's should measure low.
Repeat the above procedure, but remove the grounded test lead from U50-1. This should load all highs into all
the output ports.
To check U47, first, load U49 with all lows and tap pin 11 with the grounded test lead and measure low. Next, load u49 with all highs and again tap U47 pin 11 with the grounded test lead. The outputs should be high.
To check U's 48 and 38 load U's 49 and 39 with all lows and tap a grounded test lead to U45-10. Measure the outputs 10-8Q on each. They should all measure low. To load all highs into U48 and U38, load all highs into U49 and U39, and tap U45-10 with the grounded test lead. NOTE: if problems are encountered here the music gating circuit may be at fault. Refer to its troubleshooting procedure if necessary.
5MHZ CLOCK CIRCUIT (Test Procedure)
With a logic probe verify U2-12 is switching high and low or measure a 20MHz square-wave with a scope. U23-5 and 6 should measure 10MHz square-wave and U23-8 and 9 should measure 5MHz square-wave.
To verify proper operation of the Divide-by-Eleven circuit, tie one end of a test lead to ground and connect the other end to TP1. U24-6 should be high. Pins 11, 12, 13, 14 and 15 of U43 should all be toggling. Move the ground from TPl to pin 9 of 043. Pins 11 and 13 should be low, pins 12 & 14 should be high. Remove the ground lead from Pin 9. Check the outputs of U33. Pins 2 and 3 should be toggling and measure 227KHz.
NOISE GENERATOR
The noise generator circuitry is composed of U62, a digital noise generator, a DC blocking network C48 and R129 and a voltage follower U63. Both outputs have a minimum amplitude of 11.5v P-P, with the wave form at U63-6 centered around ground.
Test Procedure
Check for proper amplitude signal at outputs, (U62-3 and U63-6). 0U63~6 will read approximately 2.5vrms or 11.5v P-P,
POWER CIRCUITRY CHECKOUT
25 volts
A) With power applied to board, both L.E.D.'s on
— should be lit, indicating presence of plus and minus
Ve
1 If not lit, check fuse(s) on board.
2 25 volts (plus or minus) must be present at U69 and U68 input pins.
- If not, check U69 (or U68) and D1 (or D4) for shorts.
15 volts
A) 15 volts (plus or minus) must be present at U69 and U68 output pins.
1 If not check U69 (or U68), Dl (or D4) and D2 (or D3) for shorts.
2 Verify 25 volts (plus or minus) present at input pins of U69 (or U68).
+5 volts
A) Verify +5 volts (from main power supply) present at J1-9.
+2.2 volts
A) Transistor Ql and R6, R7 and R8 provide 2.2 volts to Q2 and 18.
Z +2.2 volts should be present at emitter of Ql.
2 +5 volts should be present at collector of Ql.
QUICK CHECK PROCEDURE
At this point, all of the sounds generated on the audio board can be checked. Follow the above procedure for loading all "ones" into the control latch 047. The Bug Pushing A and B_- sounds should be turned on at this time. To turn them off, ground 047 pin 12 and 15 with a test lead. With another test lead, tap the following pin numbers on U47 to activate the corresponding sounds.
SOUND CHECK TABLE
Pin number On U47....ccecccccccceccceccess Sound 2 Soft Explosion 5 Loud Explosion 6 Chirping Birds
9 Eggs Cracking 16 Beetle Dying 19 Beetle on Screen
To check the Music circuit, load all "ones" into the output latches, U48, U38 & U47 as described above. Ground U47-12 and 15 with a test load to disable the Bug Pushing A and B sound. With another test lead, ground either pin 6 or 9 of U48 to enable the music amplitude signal. With yet another grounded test lead, tap pins 12, 15, 16, & 19 on U48 and pins 2, 5, 6 & 9 on U38. A different tone should be heard for each grounded pin.
MASTER CLOCK CIRCUITRY
(Refer to Block Diagram 2)
The crystal and 3 inverters (1/2 U2) constitute a 20MHz oscillator. 023 is a J-K flip-flop used to divide the 20MHz down to 5MHz. U43 and U24 together constitute a divided by eleven circuit. This is accomplished as follows: U43 is a Presettable binary counter. By preloading the input with five (pins 3 & 5 pulled high and 4 & 6 grounded), the counter starts counting from 5 to 15 every time a clock pulse arrives at pin 2. At fifteen a carry pulse is generated at Pin 15 and is fed to Pin 2 of a D-flip-flop (U24). The output of U24 then goes low for one clock pulse. The low is fed to the load input of the counter and it starts counting from 5 to 15 all over again. Thus, the frequency at the output of 024 is 5MHz/ll. This signal is then fed to a J-K flip-flop which toggles every time a clock pulse occurs at Pin 12, making the output 1/2 its clock input of 227KHz.
Two Phase Clock
The two phase clock utilizes both halves of a 74LS74(U29). This circuit generated 2 square wave 90 degrees out of phase and their compliments. This phasing insures that U27-2, U28-2 and U24-11 are clocked in sequence,
Divide-By-23 and Load Control Circuit
U27 &U28 comprise an 8-bit binary counter. When the "B Load~" signal appearing at Pin 9 of both U27 & U28 goes low and each gets clocked, the binary equivalent of 233 gets preloaded into the 8-bit binary counter. After 23 clock cycles, the carry output of U27 (Pin 15) goes high. During the same clock cycle, this signal, also appearing at U24-12, get clocked through causing U24-8 (B Load-) to go low. Consequently the binary counter is again preloaded with 233 and the cycle repeats itself. The output of this circuit is joined with the output of the bell circuit by Current
Controlled Amplifier U61.
Divide-By Two Circuit
This circuit simple consists of a J-K flip-flop (U34) which is wired such that the output toggles every clock pulse.
Divide-By-32
This circuit is simply two cascaded 4-bit binary counters (U26). Pin 9 is a square wave which toggles every 16 clock pulses appearing at Pin 1.
Trouble Shooting
(Refer to Sheet 1 and 3 of Schematics)
Load all “ones" in the output latch, 047 as described in the input control circuitry. Monitor the signal at U19-
- It should be a square wave with a period of about 140msec. Check the signals appearing at Pins 5, 6, 8, 9 of U29, They should all be square wave with a period about 12.8usec., To insure proper operation of U's 27 & 28, ground TPS with a test lead. U24-8 should remain high so U27 & 24 will act as standard binary counters. With a logic probe or scope, check pin 11-15 on each IC. All should be toggling. Remove the ground from TP5 and move it to U24-8. Again check the outputs of U27 & 24. Pins 11, 12, 13, 15 of 028 and 11, 13, 14, 15 of U27 will be low. Pins U28-14 and U27-12 will be high. Remove the ground from U24-8. Check pins 3-6 & 8-11 of U26. All should be toggling.
LOUD EXPLOSION
(Refer to Block Diagram 3)
The loud explosion is activated whenever the cannon is blown up. The basic components of this circuit are white noise, from the digital noise generator, a low pass filter, a current controlled amplifier (CCA), an envelope control circuit and a voltage switch.
Low Pass Filter: R130, -R134, C49 and C50
The output of the noise generator circuit is fed into the low pass filter, R130, -R134, C49 and U50. The filtered output is then fed directly into the CCA(U64).
Current Controlled Amplifier (CCA): U64
(Refer to Figure 1)
U64 can be imagined as an amplifier that generates a current wave form at Pin 6 characteristic of the voltage appearing at Pin 2. The gain of the output is proportional to the amount of current injected into Pin 5.
Envelope Control: R141 and C51
R141 limits the amount of current injected into Pin 5 of the CCA and the RC time constant of R26 & C51 determines the envelope or decay time of the output waveform at Pin 6.
Voltage Switch: R135 & R136; Q23 & Q24
The circuit is turned on by placing a low level at the junction of R135 & R136. Q23 gets forward biased and turns on. This subsequently forward biases Q24 and injects current into the CCA.
Test Procedure
(Refer to Sheet 4 of Schematics)
A. Disconnect J2 from CPU board.
B. Load “ones" into input latch U47 per input control circuitry section procedure.
C. Junction of R135 & R136 should be about +5vdc.
D. Ground junction of R135 & R136
1 Collector of Q23 caused to switch from -3.5vdc to about +5vdc.
2 Q24 should forward bias; collector change from about -14.5vde to about +5vdc.
E. If voltage switch suspect, cut jumper W5.
1 Tap grounded test lead to square pad W5.
- Explosion should be heard when current injected into CCA.
2 If no explosion heard, verify functioning of noise generator.
- Verify R130 is receiving the noise signal.
F. If bell, music or bounce sounds work (reference Quick Check Procedure), replace U64.
G. If sounds per section F do not work, check voltage follower circuit (see voltage follower section).
H. If voltage follower operates, check associated CA3080's for shorts (U59, U61, U67).
1 Isolate each CCA by cutting appropriate test jumper until explosion circuit works.
Voltage Follower
(Block Diagram lle R159, U55 & U54)
R159 converts the total current output of all the CA3080's to a _ voltage. Since this is a high impedance point, U55 is used to amplify the signal at Pin 3 before feeding it to the pot driver (U54).
Test Procedure
(Refer to Sheet 4 of Schematics)
A. U55 should be functioning if any of the following sounds work.
1 Music, loud and soft explosions, bell, bounce.
If none of sounds in (1) work, cut W7
1 Apply known good signal (with a test lead) to square pad of W7..
- Use Pin 6 of U63 (noise generator) for source.
2 Noise signal should be present on speaker if input control latch (U47) set up properly to turn off all other sounds.
SOFT EXPLOSION
(Refer to Block Diagram 3)
The soft explosion is heard whenever a bomb goes off. The technical description is identical to that of the loud explosion. The difference between the two circuits only being the component values in the envelope control circuitry giving the sound a faster decay time and lower volume.
Test Procedure
(Refer to Sheet 4 of Schematics)
See Test Procedure for Loud Explosion.
BELL
(Refer to Block Diagram 4)
The Bell sound is heard at the beginning of each round and whenever a flying beetle is hit. The technical description is identical to that of the loud explosion sound. The differences between the two circuits are different component values in the envelope control circuitry. These are responsible for a different frequency response, amplitude, attack and decay times. No low pass filter is used to feed the CCA, rather the output of the Divide-By 23 and Load Control circuit to Pin 2 of the CCA U59.
Test Procedure
(Refer to Sheet 1 of Schematics)
See Test Procedure for Loud Explosion sound, and Divide-By 23 and Load Control circuits.
CANNON
(Refer to Block Diagram 5)
The cannon sound is heard whenever the cannon is fired. The circuitry to create this sound consists of a low leakage switch, voltage controlled oscillator (VCO), TTL level converter, and a binary counter.
A low level applied to the input of the low leakage switch causes a change in voltage at Pin 5 of the VCO (U60). This control voltage causes the frequency at the output of the VCO to sweep up. As the signal rides on a DC level, a coupling capacitor is used to A-C couple the signal to a bipolar- to-TTL the level converter consisting of R122-124, Q22, D21 and D22. This signal is then fed into a _ binary counter (U13) where it is divided by four. The signal is then adjusted for volume by R125-127and A-C coupled by C46 before being sent to the summing junction.
Test Procedure
(Refer to Sheet 4 of Schematics)
Load all "ones" into the output latch U47, as described in the Input Control Circuitry section. With a test lead, ground 047-12 & 15 to disable the Bug Pushing A & B sounds.
Measure the collector of 920. With another grounded test lead, tap the junction of R113 & R114, it should switch from -3.5vdce to about +5vdc. Next measure the collector of Q21. It should switch from +14vdc to GND. Pin 5 of U60 should switch from about +l4vde to about +12.5vdc.
If there is any doubt concerning the operation of Q21, lift R119 on the Q21 side. A grounded test lead may be used to simulate the action of Q21 by touching the test lead to the lifted end of R119.
Next, measure the frequency at Pin 3 of U60 with RI113- 114 ungrounded. It should have a period of about 0.86ms and be riding on a +6vdce level. It should be approximately 8V P-P in amplitude. Next ground the junction of R113-114,. The period should be about 0.2ms. Remove the ground from the junction of R113 & 114.
Next check the collector of Q22. The period should be identical to the signal at 060-3, and have TTL compatible levels.
To insure proper operation of the binary counter (U13) monitor Pin 1. Again the signal here should be identical to that of the collector of Q22. Pin 2 should be high as well as Pins 3 through 6. Next ground the junction of R113 & 114, U13 Pin 2 should now also be grounded and the output Pins 3-6 should be toggling.
BOUNCE
(Refer to Block Diagram 6)
The Bounce sound is heard if a bug is bouncing off the ring, or if anything is hit by the cannon,
The circuitry to create this sound consists of a low leakage switch, voltage controlled oscillator (VCO), a voltage switch, an envelope control circuit, a current controlled amplifier (CCA) and a driver circuit to provide an AC component, :
Low leakage switch and VCO (Q16 & 17 and U57). This portion of the circuit is identical to that found in the Cannon section, except the signal is fed to Pin 2 of the CCA rather than to the TTL level converter of the Cannon Circuit.
Voltage Switch
(Q18 & Q19), Envelope Control R110 & C41 and CCA Circuit (U59)
This portion of the circuit is identical to that found in the Loud Explosion section. NOTE: That the low pass filter of the explosion circuit is not used.
Driver Circuit
This circuit uses U58 as a driver to inject an AC waveform into the DC signal at Pin 5 of U57.
Test Procedure
(Refer to Sheet 3 of Schematics)
See Test Procedure for Cannon to test the Low Leakage Switch and VCO portion.
See Test Procedure for Loud Explosion to test the Voltage Switch, Envelope Control and CCA circuits.
To check the Driver Circuit, use a scope to verify the presence of AC waveform at Pin 5 of U57.
BEETLE ON SCREEN
(Refer to Block Diagram 7)
The Beetle on Screen sound is heard whenever a flying beetle appears on screen.
The circuitry to create this sound consists of a gated oscillator, a low leakage switch, voltage controlled oscillator (VCO), TTL level converter and a binary counter.
Gated Oscillator
(Refer to Sheet 3 of Schematics)
The gated oscillator consists of U19, R73-75 and C29 &
- The output of the oscillator, a pulse train with a period of 140 micro-seconds is fed to U20 for squaring. The output from 020-4 is fed to the low leakage switch.
Low Leakage Switch, VCO, TTL Level Converter and Binary Counter
This portion of the Beetle on Screen circuitry is similar to that of the Cannon circuit. For a technical description, see the Cannon Section.
Test Procedure (Refer to Sheet 3 of Schematics)
See Test Procedure for Cannon, with this exception:
1 After output latch U47 is set up, check output of gated oscillator U19, Pin 3 for a pulse train with period of 140 msec (7.14Khz).
2 Check for same pulse train, after squaring, at U20 Pin 4.
3 Proceed with Cannon Test Procedure.
EGG CRACKING
(Refer to Block Diagram 8)
The Egg Cracking sound is heard whenever an egg laid by a flying beetle, is cracking open.
The technical description is nearly identical to that of the Cannon sound. The difference between the two circuits is that the Egg Cracking signal is fed to the low leakage switch through an inverter, U31 and the output of the Egg Cracking circuit from the binary counter is obtained from 3 outputs of 0U22 (instead of one) and combined in a summing junction of resistors R68-R70.
Test Procedure (Refer to Sheet 3 of Schematics)
See Test Procedure for Cannon.
MUSIC (Refer to Block Diagram 9)
Various musical tones are played when the game begins, when a player receives a bonus round or bonus cannon, and with every cartoon (starting at round 2 and every 3rd round thereafter). :
The circuitry involved consists of two phase clock; a 12-bit divide-by-N counter, which determines the musical
Two Phase Clock Generator
The two phase clock generator utilizes both halves of u44. It outputs two square-waves 90 degrees out of phase and their compliments. These four clock signals are used to clock U46-1, U36-1, U37-1, and U25-11 in sequence.
12-Bit Divide-By-N Counter
U46, 36 and 37 are 4-bit binary counters cascaded to form a 12-bit counter. When the "M Load-" signal goes low at Pin 9 of each counter and all three get clocked, the data appearing at pins 3 through 6 of 046, 36 and 37 gets preloaded into the counters. This data is referred to as the number N. After 4096-N clock pulses, the carry output of U46 (Pin 15) goes high causing the "M Load-" signal to go low and the data appearing at the counter inputs is again loaded and the sequence is repeated.
Digital Music Output
The compliment of the "M Load-" signal at U25-9 is fed to pin 9 of U34. For every pulse appearing at 034-9 the "D Music +" signal at U34-5 toggles. This signal then would have one half the frequency of the incoming clock, and is always a square wave.
Music Latch Clock Gating Circuit
This circuit is composed of U's 15, 25, 35, and 45. When the CPU wants to change the frequency select lines, it sends a pulse to connector J2-11. This pulse arrives at U25-3 and forces U25-6 low. This sets the "REQ" (request) signal at U35-9 low. If no M load operation is in progress, then 035-10 goes high. When MBCLK + goes from a low-to-high transition at U45-11, 023-9 goes high and the frequency select input at 045-6 get latched to the outputs of U48 & 38.
Current Controlled Amplifier
The digital music signal from U34-5 is fed to a CCA, U67. For a technical description refer to the Loud Explosion Section.
Amplitude Controls
There are two set of amplitude controls for the music circuit; C72, C73, R193, R194, R201 and R202. These different combinations give the music circuit more versatility by allowing different volume and envelope characteristics. For a technical description, refer to the Envelope discussion under the Loud Explosion Section.
Voltage Switches
There are two voltage switches whose input come from U48 pins 6 & 9. (These voltage switches consist of Q31 thru Q34 and associated resistors.) For a technical description, refer to the Loud Explosion Section.
Trouble Shooting
With a logic probe verify that 044 pins 5, 6, 8 and 9 all toggle.
To verify proper operation of the 12 bit counter (046, U36 and U37), ground TP2 with a test lead. With a logic probe check pins 11 thru 15 on all 3 counters, they should all be toggling.
Next, move the grounded test lead from TP2 to U25 Pin
- Load all "ones" into U48 and U38 (refer to Input Control Section). With a logic probe check pins 11 thru 14 on all 3 counters, they should all be high.
Using a second grounded test lead, ground U46-6. Verify that U8-11 is now low. Repeat this procedure for pins 11 thru 14 on U46, U36 and 037.
Remove the grounded test lead from U25-8 and Place it on U48-12. The carry outputs of all three counters should be pulsing;.....also check for activity at U25 pins 8, 9 and 12; and at U34 pins 5 and 9.
OUTPUT AMPLIFIER (Refer to Block Diagram 11)
The output amplifier section consists of a preamp and volume pot driver U55 (TLO81), main driver amp 070 (TLO81) and speaker drive transistors 927 and Q28. U54 drives the external volume pot located on the coin door and its associated cable. If little or no volume is heard, use an ohmmeter to meter the pot wires between J1-8 and J1-3. The resistance should vary as the pot is rotated. If the audio is at maximum volume regardless of the pot position, suspect an open lead between ground and the pot lead connected to connector Jl-1. The final drive is a noninverting amplifier circuit containing 070, Q27 and Q28. Observe the waveform at the speaker wire which is the emitter junction of Q27 and Q28, If the upper half of any sound waveform appears clipped, suspect Q27. For the lower half, Q28 is the suspect. For no audio, meter Q27 and Q28 out of circuit and look for burned resistors R152 and R153. Also check diodes D23 and D24 at this time.
BUG PUSHING (A & B)
The Bug Pushing sound is heard whenever a bug is. pushing a bomb.
The circuit is two 4~bit binary counters (U21) dividing a 588msec pulse input by 8 (for "A") or by 16 (for "B"). The outputs of both are adjusted for level and AC coupled to the pre-amp CCA summing junction. The Bug Pushing A & B signals are fed into the 4-bit counters through inverters U31, pins 2 and 12.
Test Procedure (Refer to Sheet 4 of Schematics)
A.. Load “ones” into input latch 047 per input control circuitry section procedure.
B. Ground U31-9 (to check "A" circuit) U31-11 (to check "B" Circuit).
1 Output pins 3-6 (for "A") or 8-11 (for "B") should be toggling.
DYING BUG (Refer to Block Diagram 11)
The Dying Bug sound is activated whenever a beetle dies on screen.
The basic components of this circuit are a low leakage switch, voltage controlled oscillator (VCO). TTL level converter and 3 binary counters. The technical description is similar to that of the Cannon circuit, with two additions. The input signal of the dying bug is fed through an inverter, U31, to the low leakage switch. The output of the TTL level converter is fed to two cascaded 4-bit binary counters, with a third binary counter feeding into the two cascaded counters. The output of the counters is fed to a summing junction (R51, 52 and 53) and AC coupled to the voltage follower circuit.
Test Procedure (Refer to Sheet 2 of Schematics)
See Test Procedure for Cannon, with the following additions:
1 To check each of the three binary counters:
- Ground pin 2 or 12 of U42 (pin 12 of U32 already grounded).
- Output pins 3-6 and pins 8-1ll of 042 should be toggling.
ec) Check wave forms of U32.
- Pin 13, pulse width of 3.27msec (305.8Khz)
- Pin 8, pulse width of 52.32msec (19.1hz)
- Pin 9, pulse width of 26.16msec (38.2hz)
CHIRPING BIRDS
(Refer to Block Diagram 14)
The Chirping Birds sound is activated whenever a beetle is knocked out.
This circuit consists of two major sections; a random noise generator circuit and the chirping birds sound circuit.
The random noise generator consists of a divide-by 64 circuit (Ul), which is two cascaded 4-bit binary counters. Pin 10 is a square wave which toggles every 32 clock pulses appearing at Pin 12. This output feeds into the digital noise generator.
The digital noise generator section is comprised of one serial in-parallel out shift register. Four outputs from the shift register are mixed together via 3 exclusive-or gates, The resulting signal is then used two places: One is to feed an anti lock-up control circuit and the other is to provide the input data for the shift register through a fourth exclusive or gate. The output of the noise circuit is taken from the QH output of the shift register and fed to the input and to the first binary counter of the chirping birds sound circuit.
Shift Register
Ull is an 8-bit parallel output shift register. Random data is generated by the combination of the shift register in conjunction with a binary addition function, The clock signal for the shift register comes from the divide-by 64 circuit previously described.
Mixer
The mixer is made up of 3 exclusive-OR gates whose inputs are taken from the outputs of the shift register. The gates perform a logical addition of the four selected taps of the shift register. U12-11 is then fed back to the input of the shift register via a fourth exclusive or gate.
Anti Lock-Up Control
If at any time all outputs of the shift register become "ones", the input to the shift register will become a "one" and will lock-up in an all "ones" state. U32 is a binary counter wired up to provide the shift register with a reset pulse if it counts all "ones".
Chirping Birds Sound Circuit
The Chirping Birds sound circuit consists of a low leakage switch, voltage controlled oscillator (VCO), TTL level converter and 2 binary counters. The technical description is similar to that of the Cannon circuit, with two additions. The input to the circuit is the signal from the random noise generator, fed through an inverter, U31, to the low leakage switch. The output of the TTL level converter is fed to two cascaded 4-bit binary counters. The chirping birds enable signal from the CPU is fed to second binary counter. The output of the counter (U41-10) is fed through resister R47, R48 and R49 to reduce the volume, and AC coupled through C22 to the voltage follower circuit.
Test Procedure (Refer to Sheet 2 of Schematics)
Divide-By 64 Circuit
1 Check wave forms at these points
- Input Ul pin 1
- Should be pulse width 588msec (1Khz)
- Outputs, Ul pin 6
- Should be pulse width 9.4msec . (106Mhz)
- Output Ul pin 10
- Should be pulse width 37.4msec (26.7hz)
Digital Noise Generator
A. Ground Pin 11 of U12 with test lead
1 Using scope, monitor outputs of shift register Ull (QA through QH). They should all be toggling.
2 Pins 12 and 13 of U12 should also be toggling.
3 U32 will now act as a straight binary counter so its outputs should also be toggling.
Chirping Birds Sound Circuit
See Test Procedure for Cannon, with the following exceptions:
1 To check the binary counters:
- Ground Pin 2 (or 12) of 041
- Outputs pins 3-6 and 8-11 of U41 should be toggling.
SHAFT ENCODER
(Refer to Block Diagram 15)
The Shaft Encoder circuit is designed to supply information to the CPU board as to the position and direction of rotation of the shaft encoder on the control panel.
The shaft encoder circuit consists of two voltage comparators with hysteresis, two TTL level converters, a series of seven flip-flops supporting two up/down binary counters, and a quad 2-input multiplexer (U18).
The shaft encoder unit on the control panel provides two square-wave outputs, 90 degrees out of phase. The phase relationship of the two outputs (which one leads) determines the direction (clockwise or counter-clockwise -- CC or CCW) information used by the shaft encoder circuit.
Comparators
The comparators (U65 and U66) compare the shaft encoder outputs to the reference voltage (+2.5v taken from network R168, R170 and C62), and will nominally switch high when the input reaches 3.47 volts, which will switch pin 6 low (1.8v or below).
TTL Level Converter
Transistors Q29 and Q30 are bi-polar to TTL level converters, feeding thru inverters U20.
Direction Flip-Flop
The first half of U10 detects which direction (CW or CCW) the shaft encoder is being rotated using signals WCl+ and WC2+.
Control Logic Circuit
The second half of 010 and U8, U7 and U6 insure that signals reach the up/down counters at the proper times. U10 will send a change of direction signal (causing the counters to count up or down) at the proper time, as the up/down count pin 5 can only change when the clock pulse input (pin 14 of U16) is high.
U8 and U7 synchronize the input pulse to pin 14 of Ul16 to arrive at the proper time.
U6 is used to synchronize the halt signal from the CPU with the clock pulse on pin 14 of U16. The halt signal from the CPU will disable the counter.
Counter
U1l6 and U17 form an 8-bit up/down binary counter, counting the pulses received from the shaft encoder.
Multiplexer
U18 is a two input multiplexer. It allows the CPU to read either of the 4-bit outputs of the counter, depending on which set the CPU selects. The outputs from the multiplexer are fed to J2 and off to the CPU board.
Test Procedure
Comparators and associated circuits
A) Check for 2.5 volts on pin 2 of U65 and U66
1 If not present, and +5 volts OK, either U65 or U66 is bad
B) Ground J3 Pin 1
1 U65 pin 6 should measure 10 volts or above
D) Repeat instead of Collector of Q29 should be .3 volts or less
U10 pin 2 should be high
pin 1 to +5 volts
U65 pin 6 should be -10 volts or below
Collector of Q29 should be high (around +5 volts)
U10 pin 2 should be low
"B" and "C" for U66 comparator, using J3 pin 3 J3 pin l.
Shaft Encoder and Direction Circuit
A) Monitor U10 pin 5 while rotating shaft encoder on control panel
Pin 5 should go high when shaft encoder rotated in one direction and low when rotated in the opposite direction.
If pin 5 does not respond correctly, either shaft encoder is bad or direction circuit is bad. Proceed with 3 to determine which.
Disconnect the shaft encoder.
- Ground J3 pin 1. WCl (020 pin 6) should be high
- With test probes attached to ground, and +5 volts, pulse J3 pin 3 to ground followed by a +5v pulse to J3-3, and another pulse to ground,
- At this time, WC2+ (U20 pin 4) should be high and 010 pin 2 will latch al.
- Leave J3 pin 3 at ground, pulse J3-1 with +5 volts
- U10 pin 2 should go low
£) Pulse J3 pin 3 with +5 volts again
- U10 pin 5 should go low, and U10 pin 9 will track U10 pin 5.
If all steps in" 3" are OK, all circuitry from J3 through U10 is good.
- If board failed test A.1 and passed all
6-20
of test 3, the shaft encoder is bad.
Control Logic Circuit
A) Ground TP4; count flag should go high
B) Use a dual trace scope and sync the scope on A CLK+.
C) Check signals on the timing diagram (Schematic Sheet 5) to A CLK+.
D) To check out U8, remove ground from TP4 and ensure shaft encoder is hooked up.
1 Count flag should be low
2 Spin shaft encoder on control panel and check for pulse activity on U8 pin 5.
E) To check out U6, ground the inverter before U6 (ground U30 pin 3).
1 Pin 9 should go high, pin 8 should go low.
Counters
A) Ground U30 pin 3, (the inverter before U6).
1 U6 pin 9 should go low.
2 Ground TP4.U16 and U17 should now operate as a binary counter.
3 Rotating the shaft encoder will cause the counters to count up or down depending on what direction the shaft encoder is rotated.
4 Check the outputs of U16 and U17 for counts.
Multiplexer
A) Ground TP4
B) Force U10 pin 9 (L DIR+) to go low using test procedure for Direction Circuit, 3a through g.
1 Outputs of U18 should be low
2 Ground 018 pin 15
3 Pulse.activity should be present on the outputs of the multiplexer.
C) Ground U50 pin 1 (inverter before Data + line).
1 U17 outputs will be selected. Verify long pulses present at outputs of U16 with scope.
D) Remove ground from U50 pin 1
1 Ul6 outputs will be selected. Verify short pulses present at outputs of U18 with scope.
N34d1L4I4 WVYOVIG X00 Td (Ge'2Z'l SNId 2P) gin ZIn‘gIn ‘aa ndd OL YGLNNOD
YaXA dL INN NMOG/dN a ~¥aLNNO :
(1 SNId €P) YSGOONA LIVHS WOYS gN'BNZNOINY Lingala 91907 TOYLNOD
ony O€0'62D 99n’ssn dO1s-di13 NOI LOSuIG
YOLVYVdNOO YAGCOONS LAVHS
CPU BOARD
The processor hardware can be broken down into five basic functional blocks as shown in Figure 6-1. The arrows indicate the possible data flow directions between the various blocks. The ALU and Control block are the main components of the processor while the Memory and I/O blocks may be thought of as merely peripherals. Figure 6-2 is a detailed block diagram of the processor. The numbers in each block correspond to the entries in Table 6-1, which lists the IC numbers of the main components of each functional block.
Figure 6-1. CPU Functional Block Diagram
6-34
The following is a brief description of each block shown in Figure 6-1. The numbers beside each functional block name are the numbers in Figure 6-2 which correspond to a particular function:
RAM (6)
The RAM is implemented with three read/write static memories configured as a 256 x 12 bit block. Data can be transferred to or from this memory via the ALU block. The processor uses this RAM as a scratch pad.
ROM (10)
The ROM is configured as a 32K x 8 bit block of memory. These memory locations contain the program instructions and/or data. It is accessed via the processor control unit.
I/O 19, 17, 18
The I/O block consists of 8 output lines implemented with a bit addressable latch, 24 input lines implemented with data selectors, and two 12 bit registers which are connected to the X Y display deflection circuits via D/A convertors.
Arithmetic Unit 1,2,3,4,5
The arithmetic unit performs all the arithmetic processing for the system. It consists primarily of two 12 bit accumulators, an arithmetic logic unit and various data selectors. The accumulators can function as temporary storage registers for arithmetic functions upon the data in the accumulators. The data selectors are used to select the various sources of data which will be processed.
Control Unit (15,16,14,7,8,9,11,12,13)
The control unit is the heart of the processor. It performs all instruction decoding operations and generates all the necessary control signals which the rest of the hardware requires to function correctly.
The following is a discussion of each block shown in Figure 6-2:
- Accumulator Selector
The accumulator selector consists of 3 quad data selectors. They are used to select the output of either the primary or secondary accumulator for processing by various other sections of the systems.
2_& 3 Primary and Secondary Accumulators
The two 12 bit accumulators are implemented with quad bidirectional shift registers. The primary accumulator consists of S4, P4, M4. The secondary accumulator consists of T4, R4, N4. All data manipulation in the processor is accomplished using these two accumulators. All output data flows through these registers.
- Arithmetic Logic Unit (ALU)
The ALU is used to perform all necessary arithmetic functions within the processor. The ALU is implemented using three 24LS181 (N6M6L6) function generators, three 74LS85 (N9,M9,L9) 4 bit magnitude comparators, and a 74LS182 (L4) look ahead carry generator. The data which the ALU manipulates can come from four different sources. The first source is the contents of the accumulators via the accumulator selector. The second and third sources are the ROM and RAM data outputs via the ALU data selector (N11, M11, L11) and the fourth source is the external input selector (E4, D4, C4).
- Data Selector
The data selector is used to read data into the ALU from either the RAM or ROM memory. Note that the ROM data is only 8 bits wide while the RAM data is 12 bits wide.
- RAM Storage
The system RAM consists of three 9101C high speed static memory chips connected as a 256 x 12 bit block. The block is 12 bits wide in order to allow the contents of an accumulator to be stored. The processor uses the RAM as temporary storage of program variables, data pointers or any other data of a dynamic nature.
- RAM Address Selector/Register
The output of this register is tied directly to the address lines of the RAM. It consists of a multiplexer which routes address data from either the ROM or RAM locations to the RAM address lines. The capability to use RAM data to select RAM addresses is the basis for the indirect addressing mode of the processor.
- Page Selector
The page selector is used to latch the high order 4 bits of a RAM access instructions.
- ROM Data Register
The register is used to temporarily hold data from the ROM during an instruction fetch.
- ROM Memory
The ROM memory consists of the actual memory chips plus a data selector and latch circuit. The latch is used to improve the memory access time during a two byte instruction fetch by allowing one byte of the instruction to be latched while the RAM address lines are decoded for the other byte. The data selector can then be used to rapidly access both bytes of the instruction by switching between the latch and memory outputs.
ll. Instruction Register
The instruction register is a latch which holds the current op code as read from ROM. Its output is tied to the instruction decode circuitry which in turn generates the necessary signals to execute the instruction.
- System Sequencer
The system sequencer is used to decode an instruction op code and to generate the appropriate timed sequence of signals which execute the instruction. The op code is decoded by using it as the address data to a set of decoder ROMS. The outputs of the decoder ROMS are then synchronized with the system clock and used to control the various system functional blocks.
- Line Length Counter
The line length counter is used during the process of drawing a vector to control the length of a vector, by turning off the beam at a pre-determined time after the vector is initiated. The counter is loaded with a value from a line length ROM and then counts up until it overflows which in turn generates a signal to indicate the vector has been finished.
14, Program Address Selector
This selector is used to provide the address data to the program ROM. It selects either the program address counter output or the accumulator selector output and routes this data to the ROM address lines. The ability to use the accumulator
contents as address data allows the program to randomly access data tables stored in the ROM or to compute a branch address after a conditional test.
- Program Address Counter
This is a 12 bit counter whose output defines the next location in ROM to be accessed. It is normally clocked sequentially to step through a program. However, it can be loaded with data from the program address register which is how the jump instructions are implemented.
- Program Address-Register
This register is a latch used for temporary storage of an address which will be loaded into the program counter during a jump instruction. The input data to this latch can come from either the program ROM or the scratch-pad RAM.
- Input Selector
The input selector is used to read the state of one of the 24 input lines into the selected accumulator. There are 16 primary inputs and 8 secondary inputs. During an input instruction, the upper 11 bits of the accumulator are set to zero while the least significant bit reflects the state of the input line. All input lines have pull up resistors on them so that they will read high if they are left unconnected.
- Output Selector
The output selector is a bit addressable latch used to control the 8 output lines. During an output instruction, the selected output line is set to the complement of the least significant bit of the accumulator. The output lines are used to control the audio board, display intensity and the mechanical coin counter.
- Display Registers
The display registers are the interface between the processor and the display driver circuits. These registers are latches into which the contents of the accumulators can be stored. The outputs are tied to D/A converters which provide the input voltage to the display deflection amplifiers.
15.
16.
17.
18.
19. ‘N-14, M-14, TABLE 6-1.
T-2, R-2, N-2
S-4, P-4, M-4
T-4, R-4, N-4
N-6, M-6, L-6, N-9, M-9,
N-11, M-11, L-11
L-14
J-12, I-12
H-12
S-13
U-7, R-7, T-7, P-7, U-9,
T-13
A-8, G-10, F-10, G-14,
E-6, D-6, E-8, H-8, G-8,
S-9, R-9, P-9
S-11, R-11l, P-11
P-13, R-13
E-4, D-4, C-4
F-2
S-2, R-2, M-2 F-14, BLOCK NUMBERS AND COMPONENT I.C.
L-9
T-9, U-ll, T-11
E-14, D-14, C-14
F-8
6-40 To
DISPLAY
ADDRESS, ADDRESS,
REGISTER COUNTER
©
OUTPUT
SELECTOR
RAM ADDRESS.
SELECTOR &
FIGURE 6-2. DETAILED BLOCK DIAGRAM
SECTION 7
TROUBLESHOOTING
UNIVERSAL BENCH TEST
CONFIGURATION:
The components depicted in Figure A represent the integral elements and interconnects necessary to effectively bench test the Cinematronics' color vector display video game system. The configuration is universal in that the game logic board, monitor, interface board and power supply are consistent from game to game. Audio board varies in design for each new game though maintaining the pinout of its input power molex plug. Player control ribbon cable terminates at the player control panel elements of each game (i.e., Joystick, Fire & Thrust buttons, Coin Acceptor Mechanism, etc.).
POWER_INTERCONNECTS:
The power supply provides all voltages necessary for game operation.
Logic board drive is +5 volts t59 applied to pin 10 of the input power molex plug, and ground enters the logic board through pin 4 to pins 1, 5 and 6. The logic board will free run in the game attract mode with proper power applied.
The audio board accepts +25 volts on pin 4 and -25 volts applied through pin 6 to pin 8. Ground enters pin 7 and,is trace connected to speaker return pin 5. Pin 9 accepts =5 volts pc.
Power for the monitor is +25 volts through pin 6 of its molex plug to pin 5 and -25 volts on pin 8. A full wave rectified, unfiltered spot kill level of approximately +25 volts is applied to pin 14. The assembly is grounded through pin 15 to pin 12.
SYSTEM TEST CONSIDERATIONS:
As previously mentioned, the logic board will free run in the particular game attract mode solely with +5 volt applied. Ribbon cables are output lines and can be removed without affecting the free-run mode. Ribbon cable is an input
FLOURESCERT LjGnT , ‘Sesioea05!
SPEAKER
. + 71-10836-01 coLon wontTon IL
seies3-01 -ocicente0
ce J | }—encooer assy '50-11575-01
bucnostic sw ‘Seite? 01
EPROM PWE
on treeeo-or NARNESS ASS¥/-cOLCR MONITOR Ye-nz0e-0c
FIGURE A
WaMess A85"/ 0ucIOSTIC SH ‘Sernveaz-ot
POWER _suPrLY| im)
aSSY se-1162801 { er
Power ‘SUPA = Seri0e9e-0" = INTERLOCK. Sw | oN pooR '3e-10896-01 || res etoremncenne SYSTEM INTERCONNECT 7 7 1 . 7 T 7 7
line and can also be removed for test purposes while free running.
The audio board can be effectively diagnosed with proper power applied and a speaker. The logic board generates most sounds by grounding various control lines through ribbon cable. The cable can be removed and game sounds can be generated by tying these lines low temporarily with a jumper wire. Refer to the appropriate audio board schematic and theory of operation section.
The color interface board must be connected to a working CPU board so it can produce proper output signals to the Wells-Gardner color monitor. If improper data were coming from the interface board to the Wells-Gardner monitor, fuses F600 or F700 could be blown. These are located on the deflection circuit board of the monitor.
TEST EQUIPMENT:
For most test purposes, a wideband oscilloscope and a digital or analog multi-meter is adequate. Also, a tri-level logic probe for verifying the presence of digital information is recommended.
Testing and troubleshooting of the logic board is the least straightforward aspect of bench test. However, Cinematronics has developed a logic board exerciser to be used in conjunction with a signature analyzer that allows effective troubleshooting and repair with a minimum knowledge of microprocessor theory and operation. The exerciser puts a 4 bit alphanumeric code on each IC leg of each chip on the CPU board which then can be probed and read with the signature analyzer to verify proper operation. Contact the Customer Service Department at Cinematronics for details.
TEST PROCEDURES:
The first step in effective bench testing is to review the system theory of operation included in the manual. Discussed are principles from the mathematical concept of vector systems to the actual hardware techniques employed in generating a vector video game display.
For specific troubleshooting procedures, refer to the symptom-remedy diagnostic chart included in the manual.
TABLE 7-1. TROUBLESHOOTING GUIDE
PROBLEM PROBABLE SOLUTIONS
Listen for audible "clatter" from the deflection yoke on the CRT neck. If the clatter is present, deflection circuitry is working and the problem is in one of the intensity circuits. No Picture
No high voltage.
If game audio is present, the CPU board is functional and the problem is in the monitor or the interface board. If the audio is distorted or absent, the CPU board is suspect. If CPU board is equipped with red led near the input power plug, verify that it flashes once when power is applied and remains off thereafter. If no LED, verify that C8 pin 6 is constantly low with a voltmeter.
Check the neck of the CRT for a glowing filament.
Be sure all connections to the CPU board and monitor are firmly seated.
If there is no filament voltage, check the line fuse from the monitor power transformer.
Check fuses F600 and F700 on monitor deflection board. Check fuses F100 and F101 on monitor deflection board.
Check H3-14 of main harness connector for a full wave rectified, unfiltered voltage signal floating at +25 volts.
An accurate high voltage to 20 KV on CRT Anode if good. Self-contained HV in accuracy.
Check cathode voltages: Screen voltage should be volts. Check for proper meter will read close high voltage is meters vary widely
Should be 150 volts. around 400 to 550 +25 and -25 volts DC.
PROBLEM
Picture on Display Jitters
No Audio
Coin Counter is Inoperative PROBABLE SOLUTIONS
Replace analog switch (LF13331) on interface board.
Check horizontal and vertical size pots for wiper noise by turning briskly while observing the screen. Readjust for proper screen size.
Check for bad solder connections on horizontal and vertical size pots.
Check DAC 80's on the interface board for bad solder connections.
Ensure that all molex connectors are properly seated.
Check for open speaker coil.
Check transistors 2N6292 and 2N6107 and nearby output components on audio board with ohmeter or transistor checker.
Check 7815 and 7915 outputs.
Check for open wiper on volume control mounted on inside of coin door.
Refer to audio board theory of operation and troubleshooting guide.
Replace F2 on logic board
Check 2N6292 transistor on logic board with ohmeter or transistor tester. Verify proper operation of A4 by grounding A4 pin 1. Coin counter should click.
Disconnect coin counter molex connector. Measure DC voltage on red wire. Meter should read +25 volts DC.
PROBLEM
Gives No Credits
PROBABLE SOLUTIONS
Tie E4 pin 12 to ground. If credits fail to appear, replace E4. If credits appear, disconnect logic board ribbon connector J3. Measure +5 volts on A4 pins 1 and 5. If missing, replace pull up resistor pack C2.
Alternately ground A4 pins 1 and 5. If credits appear, problem is in switches on coin door. Verify proper coin door microswitch operation.
Reconnect J3. Observe A4 pins 3 and 6 alternately while depressing microswitch lever on coin mechanism. Pins 3 and 6 should change states. Replace A4.
Replace F2 (74LS259) on logic board.
SECTION 8
SUGGESTED PARTS
COLOR INTERFACE
aQ us) a
AUDIO
MONITOR LF 1331
7406
2N5550
7315
7915
MC 1495
LM 318
7414
74LS259/DM8 334 74LS32
D ROM 1
20101 A2
Masked ROMS
D ROMS (1-6)
25LS181
2N6107
2N6292
TLO81/LF351
CA3080
74LS377
2688
74LS191
74LS151
DAC-80 FOR STOCK
Analog Switch
Ic Inverter
NPN Transistor 140 Volt BVCEO
+15 Volt Regulator IC
-15 Volt Regulator IC
Multiplier
Hi-Speed OP-Amp
Schmidt Trigger Inverter
Ic 8 Bit Latch
IC or Gate
IC PROM
IC RAM 256 x 4
Set of Four Contain Game Program
Custom Made for CPU
ALU
PNP Output Transistor
NPN Output Transistor
IC Op-AMP
Ic Transconduct
IC Octal D Flip-Flop (Also Used in CPU)
Noise Generator Chip Up/Down Converter
Dual 8 Line to 4 Line Multiplexer
Digital to Analog Converter
SECTION 9
BOXING BUGS
PARTS LIST
as
| ITEM | CINEMATRONICS | DESCRIPTION | QTY. |
NO. PART NUMBER |
87-11374-02 Assy, Harness, Main Wire
| 1 | 25-10561-01 | Nut, Wire |
| 2 | 34-10608-01 | Wire, 18AWG, Red |
| 3 | 34-10609-01 | Wire, 18AWG, Blue |
| 4 | 34-10610-01 | Wire, 18AWG, Black |
| 5 | 34-10906-01 | Wire, 22AWG, Twisted, Brown/ |
White
| 6 | 34-10908-01 | Wire, 18AWG, Orange |
| 7 | 34-11184-01 | Wire, Stripe, 18AWG, Blk/ |
White
| 8 | 34-11185-01 | Wire, Stripe, 18AWG, Blk/ |
Yellow
| 9 | 34-11187-01 | Wire, Stripe, 18AWG, Red/ |
Black
| 10 | 34-11271-01 | Wire, 18AWG, Twtd, Blk/White |
| 11 | 34-11273-01 | Wire, 18AWG, Green |
| 12 | 34-11407-01 | Wire, 18AWG, Yellow |
| 13 | 34-11408-01 | Wire, 18AWG, Grey |
| 14 | 34-11409-01 | Wire, 18AWG, Striped, Wht/ |
Green
| 15 | 34-11410-01 | Wire, 18AWG, Violet |
| 16 | 34-11411-01 | Wire, 18AWG, Striped, Wht/ |
Blue
| 17 | 34-11412-01 | Wire, 18AWG, Brown |
| 18 | 34-11413-01 | Wire, 18AWG, Striped, Blue/ |
Yellow
| 19 | 35-10614-01 | Pin, Male, Molex | 31 | |
| 20 | 35-10615-01 | Pin, Female, Molex | 27 |
| 21 | 35-10617-01 | Terminal, Female, Quick | 2 |
Disconnect
| 22 | 25-10580-01 | Ty Rap, W/Eyelet | 9 |
| 23 | 41-10647-01 | Conn, 12 Cir, Molex | 2 |
| 24 | 41-10648-01 _ Conn, 15.Cir, Molex | 1. | |
| 25 | 41-10649-01 | Conn, 9 Cir, Molex | 2 |
| 26 | 41-10658-01 | Conn, 4 Cir, Molex | 1 |
| 27 | 87-10984-01 | Cord, Power, W/3 Prong Plug | 1 |
9-1
| ITEM | CINEMATRONICS | DESCRIPTION | QTY. |
NO. PART NUMBER
| 28 | 25-11571-01 | Holder, Inline Fuse | iz 1 |
| 29 | 34-10907-01 | Wire, 18 AWG, White | |
| 30 | 67-11580-01 | Fuse, 5AMP Slow Blow | |
| 31 | 41-10657-01 | Conn, 6 Cir, Molex | |
| 32 | 41-10883-01 | Conn, 3 Cir, Molex | 1 |
87-11555-01 Assy, Harness, CRT Power, Slow Monitor
| 1 | 34-11635-01 | Wire, Twisted, 18AWG, Red/ |
Blk.
| 2 | 34-11636-01 | Wire, Twisted, 18AWG, Yel/ |
Blk.
| 3 | 34-11637-01 | Wire, Twisted, 18AWG, Or/Blk |
| 4 | 34-11638-01 | Wire, Twisted, 18AWG, Blu/B1k |
| 5 | 34-11639-01 | Wire, Twisted, 18AWG, Grn/Bl1k |
| 6 | 34-11640-01 | Wire, Twisted, 18AWG, Vio/ |
Vio/Blk
| 7 | 35-10614-01 | Pin, Male, Molex | 3 |
| 8 | 35-10615-01 | Pin, Female, Molex | 10 |
| 9 | 35-11604-01 | Pin, Female, AMP, 350550-1 | 13 |
| 10 | 41-10647-01 | Conn, 12 Cir, Molex | 1 |
| 11 | 41-10954-01 | Conn, 6 Cir, Molex | 1 |
| 12 | 41-11603-01 | Conn, AMP, 15 Cir 1-480710-0 | 1 |
| 13 | 25-10580-01 | Ty Rap, W/Eyelet | 3 |
87-11161-02 Assy, Harness, Coin Door
| 1 | 25-10579-01 | Ty Rap, W/O Eyelet |
| 2 | 25-10905-01 | Clamp, Cable 3/16", Plastic |
| 3 | 34-10597-01 | Wire, 22AWG, Blk |
| 4 | 34-10599-01 | Wire, 22AWG, Yellow |
| 5 | 34-10600-01 | Wire, 22AWG, Purple |
~6- -----4-—-34=-10602-01----| Wire,-22AWG,- Orange . -
| 7 | 34-10603-01 | Wire, 22AWG, Grey |
34-10906-01 Wire, 22AWG, Twisted, Brown/ White
| 9 | 35~-10614-01 | Pin, Male, Molex | 2 |
| 10 | 35-10880-01 | Terminal, Crimp, Female, | 1 |
Molex
ITEM CINEMATRONICS DESCRIPTION NO. PART NUMBER
| 1l | 41-10650-01 | Conn, 3 Cir, Molex | 1 |
87-11632-01 Assy, Harness, Encoder
| 1 | 25-10579-01 | Ty Rap, W/O Eyelet |
| 2 | 34-10597-01 | Wire, 22AWG, Blk |
| 4 | 34-10599-01 | Wire, 22AWG, Yellow |
| 5 | 34-10606-01 | Wire, 22AWG, Red |
| 6 | 34-10607-01 | Wire, 22AWG, White |
| 7 | 35-10614-01 | Pin, Male, Molex |
| 8 | 35-10615-01 | Pin, Female, Molex |
| 9 | 41-10657-01 | Conn, 6 Cir, Molex |
| 10 | 41-11579-01 | Conn, Chinch 6 Cir, 50-6A-20 |
| ll | 41-11641-01 | Conn, Key |
rr OMNI DU BRWNH HE
ro 87-11633-01
25-10579-01
34-10597-01
34-10598-01
34-10599-01
34-10600-01
34-10602-01
34-10604-01
34-10605-01
34-10608-01
35-10614-01
41-10883-01 Harness, Control Panel Ty Rap, W/O Eyelet 22AWG, Blk 22AWG, Green 22AWG, Yellow 22AWG, Purple 22AWG, 22AWG, 22AWG, Blue 18AWG, Red Pin, Male, Molex 3 Cir, Molex Wire, Wire, Wire, Wire, Wire, Orange Wire, Brown Wire, Wire,
Conn, ory.
a
ITEM NO.
Nu WN eH CINEMATRONICS PART NUMBER DESCRIPTION
20-11459-01
22-11630-01
25-10558-01
25-10559-01
25-10572-01
25-10909-01
26-11570-01
34-10596-01
37-11192-01
37-11192-02
37-11373-01
50-11575-01
25-10563-01
41-10646-01
80-10840-01
87-10846-01
25-10579-01
25-10582-01
34-10597-01
34-10599-01
34-10606-01
34-10607-01
35-10614-01
35-10615-01
41-10657-01
_ 41711879-01 41-11641-01
25-10579-01
34-10597-01
34-10598-01
34-10599-01 38-11554-01 Assy, Control Panel
Control Panel
Decal, Ctl Panel, Lexan
Nut, Hex, #10-24
Nut, Pal 5/8"
Washer, Lock, #10 Internal
Bolt, Carriage, 3/16" x 3/4" Blk. OX
Knob, Ctl Panel, B.B.
Wire, 22AWG/TC, Buss
Button, Short, White, Cocktai
Button, Short, Red
Switch, W/Plastic Mntg. Brkt, Sher
Encoder, Shaft, PC66D-250-5
Screw, Machine, #6-32 x 1/2" Pan. HD. P.
Conn, 3 Cir, Molex
Brd, Distribution, Ctl. Pnl
R. Chl, 26 Cir, W/l Female Conn. 36"
Ty Rap, W/O Eyelet Tubing, Shrink, 3/16" Roll Stk, Bl
Wire, 22AWG, Blk
Wire, 22AWG, Yellow
Wire, 22AWG, Red
Wire, 22AWG, White
Pin, Male, Molex
Pin, Female, Molex
Conn, 6 Cir, Molex
Conn, Chinch 6 Cir, 50-6A-20 conn, Key,
Ty Rap, W/O Eyelet
Wire, 22AWG, Blk
Wire, 22AWG, Green
Wire, 22AWG, Yellow
9-4 QTY.
Sr a a
PrP we
ue!
| ITEM | CINEMATRONICS | DESCRIPTION | QTY. |
NO. PART NUMBER
32 34-10600-01 Wire, 22AWG, Purple 33 34-10602-01 Wire, 22AWG, Orange 34 34-10604-01 Wire, 22AWG, Brown { 35 34-10605-01 Wire, 22AWG, Blue 36 34-10608-01 Wire, 18AWG, Red
| 37 | 35-10614-01 Pin, Male, Molex | 2 |
| 38 | 41-10883-01 Conn, 3 Cir, Molex | 1 |
38-10896-01 Assy, Coin Door, W/Lam
| 1 | 20-10896-11 Coin Door W/Lamps | 1 |
| 2 | 22-10899-01 Decal, "Cinematronics" | 1 |
| 3 | 25-10556-01 Nut, Hex #4-40 | 3 |
| 4 | 25-10570-01 Washer, Lock, #4 Internal | 3, |
| 5 | 20-10868-11 Brkt, Short Vol. Cntl/Counter | 1 |
| 6 | 25-10557-01 Nut, Hex, #6-32 | 2 |
| 7 | 25-10563-01 Screw, Machine, #6-32 x 1/2" | 2 |
Pan. Hd. P.
| 8 | 25-10571-01 Washer, Lock, #6 Internal | 2 |
| 9 | 29-10590-01 Meter, Coin | 1 |
| 10 | 35-10615-01 Pin, Female, Molex | 2 |
| 11 | 65-10812-01 Diode, 1N4003, Encpl | 1 |
| 12 | 26-10589-01 Knob, Volume | L |
13 34-11013-01 Wire, 22AWG, Twtd, Blue/Red/ Green
| 14 | 35-10614-01 Pin, Male, Molex | 1 |
| 15 | 35-10615-01 |Pin, Female, Molex | 2 |
| 16 | 41-10885-01 Conn, 9 Cir, Molex | 1 |
| 17 | 51-10722-01 Pot, W.Lk.Wsr/Nut, 10K Ohm | 1 |
| 18 | 25-10579-01 Ty Rap, W/O Eyelet | 4 |
| 19 | 25-10905-01 Clamp, Cable 3/16", Plastic | 4 |
20 34-10597-01 Wire, 22AWG, Blk
| 21 | 34-10599-01 |Wire, 22AWG, Yellow | - | | |
22 34-10600-01 Wire, 22AWG, Purple 23 34-10602-01 Wire, 22AWG, Orange 24 34-10603-01 Wire, 22AWG, Grey 25 34-10906-01 Wire, 22AWG, Twisted, Brown/ White
9-5
CINEMATRONICS PART NUMBER
35-10614-01
35-10880-01
41-10650-01
38-10891-02
20-10868-01
25-10557-01
25-10563-01 win
25-10571-01
29-10590-01
35-10615-01
65-10812-01
34-11013-01 orn nu es
35-10614-01
35-10615-01
41-10885-01
51-10722-01
38-11628-01
20-11606-01
25-10558-01
25-10568-01
25-10909-01 eB wn e
25-11392-01
43~-11552-01
82-10842-20
25-10580-01
34-10597-01
34-10600-01
35-10615-01 Bw ne DESCRIPTION
Pin, Male, Molex
Terminal, Crimp, Female, Mole 3 Cir, Conn, Molex
, Coin Meter/Vol Cntl
Brkt, Short Vol. Cntl/Counter
Nut, Hex, #6-32
Machine, Hd. P.
Lock,
Coin Screw, #6-32 x 1/2" Pan.
Washer, #6 Internal Meter,
Female, Molex
1N4003,
Wire, 22AWG, Twtd, Green Pin,
Diode, Encpl Blue/Red/
Pin, Male, Molex
Pin, Female, Molex
Conn, 9 Cir, Molex
Pot, W.Lk.Wsr/Nut, 10K Ohm
Plate, P/S & Transformer
Mtg, P/S, Transformer
Nut, Hex, #10-24
Washer, Flat, #10 x 1/2"
Bolt, Carriage, 3/16" x 3/4", Blk, OX Assy, Plate,
Bolt, Carriage, 3/16" x 1 1/4" Blk
Transformer, Color Monitor, Low Sp Power Supply, Condor
Assy, Diagnostic Switch Ty Rap, W/Eyelet
22AWG, Blk
22AWG, Purple
Female, Molex Wire,
Wire,
Pin,
9-6 NN
PNP ND
PeENe
= © © FH
w
| ITEM | CINEMATRONICS | DESCRIPTION | QTY. |
NO. PART NUMBER ae ee — 5 1 41-10659-01 Conn, 3 Cir, Molex 20-10863-01 Brkt, Interlock Switch, SC 37-10893-01 Switch, Interlock 1
38-10894-91 Assembly, Coin Drawer
| 1 | 20-10862-01 Brkt, Coin Box Tong, SC | 1 |
| 2 | 20-10864-01 Handle, Coin Box, SC | 1 |
| 3 | 20-10871-01 Coin Box, SC | 1 |
| 4 | 20-10872-01 Cover, Coin Box, SC | 1 |
38-10638-01 Assembly, Speaker
| 1 | 20-11382-01 Grill, Speaker | 1 |
| 2 | 71-10834-01 Speaker | 1 |
38-10892-01 Assembly, Interlock Swt, Back Panel
20-10863-01 Brkt, Interlock Switch, SC 1 37-10893-01 Switch, Interlock 1
38-10640-01 Assembly, Fluorescent Lamp 01-10505-01 Lamp, Fluorescent 1 26-10588-01 Fixture, Lamp, Fluorescent
ITEM
nun Fw ~-} —81-11453-01 - CINEMATRONICS PART NUMBER DESCRIPTION
25-10563-01
41-10646-01
80-10840-01
87-10846-04
81-11460-01
36-10620-01
36-10621-01
41-10661-01
44-10698-01
63-10784-01
63-10944-01
80-11460-01
38-11569-01
81-11460-01
36-10620-01
36-10621-01
41-10661-01
44-10698-01
63-10784-01
63-10944-01
80-11460-01
05-11507-01
02-11507-01
02-11507-02
02-11507-03 Assy, Board, Distribution—
Screw, Machine, Pan Hd. P
3 Cir, Molex #6-32x1/2"
Conn,
Brd, Distribution, Ctl Pnl
R. Cbl, 26 Cir, w/female Conn. 36"
Assy, Board, 32K Rom
Socket, 16 Pin, I.C., Dip Solder Ta
Socket, 24 Pin, Solder Ta
Conn, 6 Cir, Molex
Ic, 74600
Cap,. 1 MF Disc 203%
Cap, 100 MF 35V Electrolytic Radia
Brd, 32K Rom I.C., Dip
Board 32K Rom
Assy, Brd, 32K Rom
Socket, 16 Pin, I.C., Dip Solderta
Socket, 24 Pin, Solderta
Conn, 6 Cir,
Ic, 74S00
Cap,. 1MF 50V Disc 20%
Cap, 100MF 35V Electrolytic Radia
Brd, 32K Rom
Assy, E Prom
U1B,
U2B,
U3B, Assy,
I.C., Dip
Molex
Kit,
B.B.
B.B.
B.B. B.B.
E Prom,
E Prom,
E Prom, wor
PPP Be Pe
ITEM NO.
Bw roe J o2-11507-05— CINEMATRONICS PART NUMBER
02-11507-04
02-11507-06
02-11507-07
02-11507-08
87-11573-01
41-11576-01
87-10847-02
87-11574-01
41-11577-01
87-11578-01
81-11142-02
01-10500-01
35-10616-01
35-10965-01
36-10619-01
36-10620-01
36-10621-01
37-10625-01
41-10652-01
41-10653-01
41-10654-01
41-10655-01
44-10667-01
44-10671-01
44-10675-01
44-10676-01
44-10677-01
44-10678-01
44-10679-01 DESCRIPTION
E Prom, U4B, B.B. ‘E Prom, U1A, B.B. E Prom, U2A, B.B.
E Prom, U3A, B.B.
E Prom, U4A, B.B.
Assy, R, Cable, 16Cir, 8.5" 32K Rom
Conn, 16 Cir Dip, IDP-163 R. Cbl. Flat 16 Cir.
Assy, R. Cable, 24 Cir, 10" 32K Rom
Conn, 24 Cir Dip, IDP-246
Ribbon Cable, Flat 24 Cir
Assy, Board, Logic w 32K Mod Tubing, Teflon 22AWG Thin Points, Test K27C
Jumper, 16 Pin, Dip
Socket, 14 Pin, I.C., Dip Solderta
Socket, 16 Pin, I.C., Dip Solderta
Socket, 24 Pin, I.C., Dip Solderta
Switch, Dip, 7 Pole
Conn, 16 Cir, Male Header
Conn, 26 Cir, Male Header
Conn, 34 Cir, Male Header
Conn, 12 Cir, Molex
Ic, 2101A2
Ic, 7425
IC, 74265
Ic, 25LS181
Ic, 74LS00
Ic, 74LS02
Ic, 74LS04
9-9 OR RWW PP Pee
CINEMATRONICS PART NUMBER
44-10680-01 Ic, DESCRIPTION
74LS08 44-10681-01
44-10682-01
44-10683-01
44-10684-01
44-10685-01
44-10686-01
44-10687-01
44-10688-01
44-10689-01
44-10690-01
44-10691-01
44-10692-01
44-10693-01
44-10694-01
44-10695-01
44-10696-01
44-10697-01
44-10698-01
44-10699-01
44-10700-01
44-10701-01
44-10702-01
44-10703-01
44-10704-01
44-10705-01
44-10706-01
44-10707-01
44-10708-01
44-10709-01
44-10710-01
44-10711-01 ‘IC,
Ic,
Ic,
Ic,
IC,
Ic,
Ic,
Ic,
Ic,
Ic,
Ic,
Ic,
Ic,
Ic,
Ic,
Ic,
Ic,
Ic,
Ic,
IC,
Ic,
Ic,
Ic,
Ic,
Ic,
Ic,
Ic,
Ic,
Ic,
Ic,
Ic, 74LS10
74LS27
74LS32
74LS75
74885
741886
748107
74LS151
74LS157
7418163
748164
74LS194
74LS257
74L8259
74L8298
74L8377
7418393
74800
74802
74804
74808
74810
74832
748113
745158
748182
748287, DROM-1
74S288, DROM-2
748288, DROM-3
748288, DROM-4
748288, DROM-5
9-10 Roe Pe eee Pe NN RFP NE NNTDTNHYWDOrY © MeN HY WD Bw Ww}
ITEM NO.
“52 CINEMATRONICS PART NUMBER
~~ a4=10712=01-—
53-10726-01
53-10731-01
53-10732-01
53-10734-01
53-10738-01
53-10746-01
53-10753-01
53-10762-01
53-10779-01
63-10783-01
63-10785+01
63-10808-01
65-10811-01
63-10810-01
65-10814-01
66-10816-01
66-10825-01
69-10833-01
80-10837-01
34-10594-01 DESCRIPTION QTY.
“IC, 748288, DROM-6 ~~
Res, 100 OHM 1/4W 5% C.
Res, 330 OHM 1/4W 5% C.
Res, 470 OHM 1/4W 5% C.
Res, 1K OHM 1/4W 5% C.
Res, 2.2K OHM 1/4W 5% C.
Res, 10K OHM 1/4W 5% C.
Res, 30K OHM 1/4W 5% C.
Res, 560K OHM 1/4W 5% C.
Res, 1K OHM 16Cir Dip Pack
Cap,. O2MF 50V Disc 20%
Cap, 680PF 100V Disc 20%
Cap, 3.3MF 35V Dip Tantalum 10%
Diode, Signal 1N914B
Cap, 22MF 35V Dip Tantalum 103%
Led, Til 220
Transistor, NPN 2N3904
Transistor, NPN 2N6292
Crystal, 20 MHZ
Brd, Logic
Wire, 30 AWG, Blue, Kynar
9-11 an NP RrPNHYF NFP NRHP
vu Ho
N
PPP NeE DN
APPENDIX A
Assembly Drawings
Schematics
and
Wiring Diagrams
Al
A2
A3
A4
A5
A6
A7
A8
AQ
Alo
All
Al2
Al3
Al4
Al5
Al6é
Al7
Al8
Alg
A20
A21
A22
A23
A24
A25
A26 APPENDIX A
TABLE OF CONTENTS
ASSEMBLY DRAWINGS
SCHEMATICS
AND
WIRING DRAWINGS
TOP ASSEMBLY, BOXING BUGS
SYSTEM INTERCONNECT DRAWING
WIRE LIST, COLOR UPRIGHT
POWER SUPPLY AND TRANSFORMER MOUNTING PLATE ASSEMBLY
POWER SUPPLY PINOUT ILLUSTRATION
CONDOR POWER SUPPLY SCHEMATIC
NATIONAL POWER TECHNOLOGY POWER SUPPLY SCHEMATIC
CONTROL PANEL ASSEMBLY
CONTROL PANEL SCHEMATIC
C.P.U. BOARD ILLUSTRATION
C.P.U. BOARD MAJOR COMPONENT DRAWING
C.P.U. BOARD SCHEMATIC
C.P.U. BOARD SCHEMATIC
C.P.U. BOARD SCHEMATIC
C.P.U. BOARD SCHEMATIC
C.P.U. BOARD SCHEMATIC
C.P.U. BOARD SCHEMATIC
32K MEMORY BOARD MAJOR COMPONENT DRAWING
32K MEMORY BOARD SCHEMATIC
HEAT SINK ASSEMBLY
AUDIO BOARD SCHEMATIC
AUDIO BOARD SCHEMATIC
AUDIO BOARD SCHEMATIC
AUDIO BOARD SCHEMATIC
AUDIO BOARD SCHEMATIC
AUDIO BOARD SCHEMATIC
D FLUORESCENT LAMP ASSEMBLY 38-10640-01 SPEAKER 71-10834-01
SPEAKER GRILL 82-01 GLASS CRT 92-11605-01 MONITOR
PLAYER CONTROL PANEL ‘ASSEMBLY 38-11554-01 CIRCUIT PANEL ASSEMBLY
> +4] com boon ASSEMBLY. ——~| 38-108SE-11 jr otetonenee tenn FRONT VIEW vas COIN DRAWER 38-10894-01 38-11572-O1
INTERLOCK WITCH ASSEMBLY (DIAGNOSTIC) POWER SUPPLY ‘ASSEMBLY 38-11628-01
‘ASSEMBLY INTERLOCK ‘SWITCH ASSEMBLY 38-10892-01 (2 REQD)
RIGHT SIDE VIEW TOP &SSEMB.( (BOXING BUGS)
snags Smo
assy andar Wamod
Connve TOR [ FROM [TO] COLOR LENGTH | REMARKS ir} [esioR [aw Pin] TEN | REMARKS
Wa FONE SuPAY uo EF 63-C9-1042 LAMP LAMP BLACK waite [Awe Tan MC mae “TWIST PAIR,
GREEN GREEN wuTe Wee, RED/BLY RED BROW, waite Rows WiTE.
Pai suit cARTH NEUTRAL,
ry re ry rs ‘6 SWTCHED A.C Wis PNK 3 VAL “TwSt PAIR ea vac
Ione 1 || voce CRC HUTS Tie-1 yeLow RED GRAY 1B 1B SPOT KWL +25 TONNECTIOR | FROM T wat Had 133, waa H35 3-0 nat INTERFACE. H3 MOLEX 03-09-2153 42-4 HO-5 H2-9 H2-@ w2-1 BROWN ry ry ir ir we ry rs Fe REF G3VAC NOT USED NOT USED NOT USED NOT USED FE REF +25 REF @AVAC, FE REF -25 ‘NOT USED NOT USED NOT USED GND REF +5 REF SPOT NAL. REF GND
418g INTERLOCK He com He HBNO. 49 BLK 42-3, BLU/VEL RED/BLN, ry a a
AC 48 GRN LINE CORD H9 WAT Ho H9 BLK Hat Hee 48 COM ir rey ry ™ wn ae) one | w/FLLS
10-1 10-2 HID-3 10-4 10-5, COIN DOOR H10 MOLEX 93-09-1093, Hast Hes Ha-4 Ha-3 Hab H2-@ 42-5 WHT/6RM BROWN VIOLET RED wT Buu. BROWN waite Z255uu0 3 ooRt THst Nu seo fer METER REF -23 age 1 <T REF UA WA! REF 3 ke hot 1320 |
j ~ BLUE BLUE ORANGE ORANGE ORANGE BLACK, BLACK BLK ANAT ir ir rs ry ir ry rs 1B “25 +5 rey +5 ‘aNd GND GND
- COMM, #5, 47, OMNTTED 6 O1NEF END TERMINATED WYO. (NOTE 5) 5.G-FLUALE QUICK DISCONNECT. 4 ~ FEMALE SOCKET 02-09 B.M=NALE PIN 02-09-2118 2.WN= WIRE NUT CONNECTION,
- TWISTED WIRE LENGTH ARE AFTER TWISTING
ONE PER INCH, jo etonenese seen hace a3 unio N82 Ha Chew MOLEX LON 03.09.1093 14-4 a4 fee Han WHT/ERN GREEN RED GRAY VIOLET BLACK, RUE vOLUME ‘SEE NOTE © VOLUME REF 925, SEE NOTE & ee) VOLUME REE +5
Zuuuun une 32K EPROM Hu MOLEX (03-09-1063 He-lt REFGND NTL ED NUT User NUT USED | Not a> REFS |
POWER INPUT TO MONITOR 412-1 TRANSFORMER Hi2 -2 HI2 HI2-3 MOLEX 03-09-1038 HHS CAP H2-2 Het RED 18 (O) > wen 1B 43)
ne Ie
ry rr B ry NOT useD. NOT USED. ca" METER REF GND REF GND GND GND NOT USED NOT USED NOT USED F REE +5, F NOT USED NOT USED.
rae rere MONITOR TRANSFORMER 143 cap Fuse = 4430007
H13, wrest Hee, RED RED rs se WIRE LIST COLOR UPRIGHT peer P= sree]
8 T 7 T 6 2 T 1
10-24UNC RIVE LO. BOLT, CAKFINGE. , BLK OX 25-10552- 01 #10 WASH, FLAT 25-10508-01 AIO WAG, LOCH AUTEKGIAL 2£-1057%-04 c 10 240NC NUT, HEX 2510558 ‘AI
4etan A-4 {| fost oeetomens creo POWER SUPPLY (N.PT) _SHOWN
82- 10842-40 ALTERNATE POWER SUPPLIES: B2- 10642 -21 (CONDOR) 82-10842-31 (DATA POWER) Vio/ERY/N10
Nh PRIMARY ¢ (way WHT/6RN/BLK
VO MOUNTING PLATE 20- N@06-01 eo TRANSFORMER , COWR MuNIToK 43-1552 -O1 10-Z4UNC V2 LG BOLT, CARRIRGE , BLK OX 2'5-10851-01 810 WASH, FLAT 25> 10506-c1 + READ MG WASH, LOCK, INTERNAL. 28-10572-01 10-24 NUT HEX 25-10558-0
i NOTES: UNLESS OTHERWISE SPECIFIED
Dy same nunse Fuse. A ane tae rese. BY BAMP UKE CIRCUT BREAKER CB I. By SAMP LINE CIRCUIT BREAKER COE [econecroe ora | leasaalwies Couoe| FuucTioN | [yew | Back [7xFve Luge! | [Je-2 [wire [TEM wuG=3 | [ves | mace [Teme usee | [e-¢[wurre |rxeme Licad |
POWER SUPPLY CONECTORS
LBL tosr-05 ||
CORRECT FUSE
AND VOLTAGE
SELECTION: HO VAC. nS vac 230 VAC CHASSIS / EARTH
GROUND
i + SCHEMATIC SET FOR IIS VAC OPERATION
qj [omens cree Fey a
Ri RT 470.0 few s70. yw SPOT KHL
4700. 2 W mites cer Ws4or ae cra | e800 |+ + | ctoas Sa%Sarew sy Br T sods Tox
BBV
cra 5401 cs
cre 1N4003
8 7 1
PROPRIETARY
THIS DOCUMENT 18 THE PROPERTY
OF warionat PoweR TECHNOLOGY, ef REPRODUCED On ;TED WITHOUT WRITTEN ATION OF NATIONAL POWER, ‘TEeMMOLOSY INCOAPORATED. J2
NOTES: UNLESS OTHERWISE SPECIFIED
ae
BUTTON ASSY SHORT, WHT (4)
37-11192-01 SWITCH W/MTE @) 37-11373-01 PAL NUT 25-10859-01
NUT HEX @10-24 @), 25 -1058B-O1 CONTROL PANEL. 20-1188 -O1 wee 18 BSP WIRE LIST.
FROM a}
PHBL
ENCODER ASSY ‘SO-11575-O1 lo-amens aacaaaadg ZI Gut si PRO-e PBS-2 PRa-2 Paa-2 PB2-2
WIRE, Buss 34-10596-01
(PRE) oO
cannon (P85) GLOVE 64 }) PLavER 2 84) PLAYER | a3) KNOB SKIRTED, BLACK e-WS7I-O1
(Par (PB2) CANNON GLOVE (Pwe!) é h3aa i] ®
BLITTON ASSY SHORT, RED 37-11192-02 SWITCH W/ MTS ‘37-11373-O1 PAL NUT 25-10559-08
LEXAN OVERLAY (CFARSIDE) 22-11630-0) AX cinewattonies P/n. NOTES Untess omenwseePeCrieo SHAFT ENCODER HARNESS, ASSN 87-11682-01 BLACK ‘BLITTON ASSY SHORT RED |(P2) Fy 02 Ot PAL NUT 25 ~10589-01 VIOLET DISTRIBUTION BOARD BI\as3-O1 321 BAIR RECEPTACLE w/TAB OLEK # 03-09-10: 41-10083-01 cinemarronics Peal Bal a Fe lsecisseola| Sl bee
8 I 7 T 6
4 [. 3 Y 2
gee aan
PROPRIETARY
THIS DOCUMENT IS THE PROPERTY
OF CINEMATRONICS INC. AND IS
Wor TO af REPRODUCED OR PLAYER CONTROL PANEL-REAR VIEW
me. GLOVE CANNON PLAYER /PANIC (P82) wep | °
oH H20 pds 10 snarl tL xey -— mes) sett
PINS 2EG UNUSED
HIS TO J3 ON
AUDID BD
rn
DIAGNOSTIC. SWITCH N.C. F N.C. COIN SWITCHES N.O. N.O. | MOUNTED ON A COIN DOOR B COM. Pal COM. REAR VIEW Hi2 Ey 6 :
Ed Od? OLIV) NO@ald al 3 YELLOW 2 >-[wover ORANGE
NOTES: UNLESS OTHERWISE SPECIFIED. 4 3 +
REVISIONS = DESCRIPTION } ate | ARRON
6 PII CABLE TOMO PCB weqquren. awee PHY OLE : 8M One / 26 PW ABE
70 POWER HARLESS
(POURED) OPERATOR OPTION Sw/TEH
A-10
COGIC PCB
Eiceon fae CINEMATRONICS [Nom
bacilli [PO NOT SCALE Bway)
NOTES: UNLESS OTHERWISE SPECIFIED. 4 3 f
SECONDARY
ACCUM, DISPLAY
Recisten "0 DAC 80's
ADORESS
SELECT (3) DATA SeLect @)
lgAahod ADDRESS COUNTER
INSTRUCTION ADDRESS
REGISTER REGISTER
BB Ae RAM OAT @
- REGISTER fam stornace ©) 7M Mitr L_somn ] [me TOT
AUDIO
seer | COIN CONTROL SELECT ) GRIGHTNESS HAMM iba E GAME OPTION SWITCHES INPUT SELECT @ COIN COUNT! FROM CONTROL PANEL tl
“PROCEED” =~ JHHHRDE [ a PAGE FLOP RAM AoDR. SEL. & REG. TO LF 13331 PAGE SELECT BREN ENG) ERE RGRE RENE SYSTEM seauence @
(23F) x-one of nm 02 O 000 vee ose ow
Sr Li esr) (59)
1918766.
cnsoa nmumioonrension | (34.90 enaetw1 vos sounvitene 4 ‘omar sen vecenes sinawy HIRD suum wouting CALM
v
8 7 6 l 5 t 4 «307, a7, 4c3) 635 ,3A6 409
KN KIO KO KB. vem re ach CP Bio ome d PEE Leal
sore Te jsevect 7448257 (Pama anne elo OAaliod ree
1603) 34ee2 i- TOY A 8 ; tren Ft (apay baler a alder rei
mp we
. ! (20,0 roar ore PSE EY ace ls Te Te G0 UC CBUA ISLINen AS aL. care amr Hs) ising = | aMer Oley Lsi9a ow cunph oun
i fy shang — 288 of
a (203,644
sin 2 oc 8 mga g eave reer aie 7 ke Fs bea ake ‘ a)
jon | Seer L922 j[_ res ects onerns eco 8 ] 7 6 I 5
7 | 6 ] 5 4 4 |
CARRY —
- + — Aon a CN DRE Te)
Db AAD a) a sJ 2.si61 ae ee
cue MOT otras ear ht c (Bap ac a. five ma
A-14 ue a ced ie OS A i hi BAX “bebe ws we Wl wo
5051 Fo NOTES: UMESS OMMENMSE SPECIFIED v0 atau runt Meutuers. rte orem ans vet tet oe 0 Yo arcu
7 T 6 | 5 t
A-15 SrowATUNES Ox Ges) OR no Jat OPTION os tage ace FD
Notes Unens OTwenwise specireD
i j I
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Bie vee u3e c 2732 2732 2732 24 Pn 24 PN Je4 pas socket SocKeT [Socket
BIA 2732 ane
Ja PN SockeT| je ON, SoceT Os ef 3
st af Sh sf
A-18 | S aNAey Hae
A
- CAPACITOR VALUES ARE IN MICRO FARADS, 1 C2 C10 ARE DISC CAPACITORS [NOTES UNLESS OTHERWISE SPECIFIED 8 7 T 6 8 f 4 3 32K Menon:
BiWKL RELEASE ‘004 ea 0D DATA BUS
Qe ce ES q
POWER DISTRIBUTION TABLE
83858933 e se eee eazd 5 a ag B 58838 83 Qegeevseye
BEEEEEER iad 33120,24 34s
- CONTROL PAIS 2532,
EVEN DATA Bus
1 JUMPER LEGEND Oo 2532 G--0 2732 NOTES:UMLESS GTHERWISE SPECIFIED. LRECEMBER 1981
i a ¢ Tr a 5 i < 2 "ete st. 3
iT 4 H ee
| a | 95255 | aE235 FPO] |
BY
| ¢ 93282 | OBES | 72303 £403: ° | |
| aa) sgt | “ | « | we 2 |
| a | | | o | < = |
avl JO dOL GNV YOLSISNVYL JO 30VAYNS WOLLOG 3YILNS OL GNNOdWOD TWWYSHL Alddv QNNOdWOD TWWHY3HL QVL YOLSISNVYL
4O dOL NO G39V1d SI
ANIS LV3ZH TIVWS
8 7 l 6 5 4 4 l 3 1
WIAs OD
IB + (C7) ar
kz1 TrS) ci as we viz Fe
A-21
HID+ (@C1)
TALS393 754 (asec ) Taes3ea
S68 4 sec+ (103)
CHIRPING
BIRDS. Blo oat ua Ls393
RanooM NOISE + aq 2N3506 gro
TALSO4
DYING BUG
$2.32 sect ‘BAD,
u32 14L 3393 foowersetind AUDO BOARD "BEY ed ad T
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
NOTES UMLESS OTHERWISE SPECIFIED R130 wat Rise eK 47K @ew So Gen ace)
BUG PUSHING -At (8s) csa
wu2r TALS393 ciNEMaTRONIC:
39K eK 31K 087 ~15V -15V
count+ a (SAS) Gen) MID+@O)
A-25 TLR COuNT= J2 (servsnay Pamagy west is [5 5
- unre wer tL SS ermany weur ial 5» t PRIMARY INPUT 12. TIMING DIAGRAM Cred GROUNDED) vay FLL veer SLELELIL a
as
SUH + eRe) r COUNT DELAY+ no FRCL :FREE RUNNING CLOCK
READ COUNTER feonorseme od AubIO BOAeD "eR" Pama ee ITA Tae 00
Jf Coss eetstonerm oreo cme FL FL —
Spe _mene 7 cn 2q|S_CANNON-c4ve) R163 068 67 cScaaay
W9Ae 7458 ToGo
- ? F w]e, ‘ {
‘arteun 9), bar 5 pe Fxg 40 FCT 0g F ax gps zie +sv 2N3906 24k 100K
ecm wine ilar MEN 71 Cup as4 Root KD 2N3906 owe SIK 38K
24.8377 Te] & SOFT EXPL -ca4ne) 24 | S_soud exP-caee) 3q]S cuzeme eeos-283> 4g [2_£86 cracnna-Cs08) sq [12 S44 PusHNe A+ (485) 6q LS 86 Pusuina +caas) 1g [1S 846 Prmia-cens) unten ecu) 8 HIAFGCD)
LATCH CLK +
ceo) WIC
UP JO De ss xso ool 7414 ma F uaa —] SASS EN 4LSt63 WIA Coe) TALS107
TER UNLESS OTHERWISE SPECIFIED
t z 7 T 6 T