CATHODE RAY TOMES

Suzuka 8 Hours Coca Cola Operators Manual

Suzuka 8 Hours (World, Rev C) (Namco, 1992) · Document · 48 pages · 8 sections · original scan

Page 1

Namco-America, Inc.

Operators Manual

Page 2

FCC Notice

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Pari 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
Page 3

© 1992 NAMCO-AMERICA, INC. - All rights reserved.

No part of this publication may be reproduced by any mechanical, photographic or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from NAMCO-AMERICA, INC.

Published by: NAMCO-AMERICA, INC. 150 Charcot Avenue San Jose, CA 95131 U.S.A. TEL: (408)383-3900 FAX: (408)383-0128

Printed in the U.S.A.

Page 4

namco

Operators Manual

INTERNATIONAL RACING COURSE HEE” SUZUKA CIRCLUT

Page 5

9.

10.

11. CONTENTS SPECIFICATIONS .........ceessseeees ee

PRECAUTIONS 2-1 Caution When Installing... 2-2 Caution When Handling... GAME COMPONENTS, 3-1 Carton Contents .... 3-2 Game Configuration INSPECTION...

INSTALLATION 5-1 Four-Player Game Installation 5-2 Spectator Tower Assembly. 5-2-1 Assembling Tower Base...... 5-2-2 Attaching the Tower Spectator Monitor .. 5-2-3 Installing 4-Player Game Center Filler Panels .. 5-3 Attaching Motorcycle Assembly to Game Cabinet 5-4 Two-Player Game — Attaching Marquee 5-5 Connecting Multiple Game Links 5-6 Final Setup and Adjustments ADJUSTMENTS/TESTING 6-1 Power Switch aay 6-2 Adjustment Switches on the Service Panel 6-3 Test Modes and Play Options 6-3-1 Test Mode .. 6-3-2 Changing Game Settings 6-3-3 Spectator Tower Option Screen . 6-3-4 Switch Test Screen 64 Monitor Adjustments ..... 6-5 Adjustments When Replacing Parts HOW TO PLAY.

MAINTENANCE 8-1 Game Cabinet Assembly 8-1-1 Replacing Fluorescent Lamp 8-1-2 Opening Maintenance Door 8-1-3: Replacing Fuse ..... 8-1-4 Removing EMI Cage 8-1-5 Removing Game PC Boards 8-1-6 Removing Monitor Assembly 8-2 Motorcycle Assemblly.............. 8-2-1 Replacing Bank Angle Potentiometer 8-3 Handlebar Assembly 8-3-1 Removing Handlebar Assembly Cover 8-3-2 Replacing Throttle Potentiometer 8-3-3 Replacing Brake Potentiometet 8-3-4 Removing the Throttle Assembly 8-4 Spectator Tower Assembly ............ 8-4-1 Changing Tower Lamps and LEDs 8-4-2 Replacing Spectator Tower Monitor TROUBLESHOOTING ~ GENERAL .....

PARTS LIST

GAME HARNESS WIRING DIAGRAMS ONNFCOHORRO

COBNRHHATHAA

Page 6
  • LIST OF ILLUSTRATIONS

3-1

3-2

3-3

3-4

3-5

3-6

3-7

5-1

5-2

5-3

5-4

5-6

5-7

6-1

6-2

6-3

6-4

6-6

6-7

6-8

8-1

8-2

8-3

8-4

8-5

8-6

8-7 Game Cabinet with Two-player Marquee ..........c.cscscesesescseesceeeseessneseenesneessesneseeeeasaneneesaenes 3

Motorcycle Assembly

Spectator Tower Monitor Bezel and Graphics Panels ...........scssesssseceseeneseeseessateeneenee 4

Tower Monitor Display ASSEMDIy oo... ccscceeceeeseeeseeseseseesesneeneeseneeseseseseeeeeeeesneneensneneaneae 4

Tower Pylon, Legs and Filler Panel ...........cccecsecsessessesseseesseceessnserssanenseeessesssesessnesesseesess 4

Two-player Game Configuration ..........-.cccscccecssseessesesssesssssessesseesesssessssueesnesneenesereessneeeets 5

Two-player Layout Plan...

Four-player Game Configuration ..........:sccecseeccccssseesecessueseessnesnsansseessueesesessncaureaseeesnsaneeses 6 Four-player Layout Plan ou... seseeeecseeseeeeesssssnessseenssesseeeeneeesnseseseeseeneasinessaeeesieseesneeconse 6

Assembling Tower Base .........cccsesesssesesssesereessseeseeeeseseeerseersseeenssesssseesesseessessenenenereneeess 8

Tower Filler Panels

Bike and Cabinet — Ready for COnmection ..........scecceccccceceeseesteeeeseesseesessessseesesseensaneeseesy 10

Base Arm Connection

Attaching the Two-player Marquee «........ccccsccseceseeeeccesee tenes ceeseceesesenseesseeeceteenesteneaeeeetiee 12 Link PCB Bracket

Multiple Game LINKS .......... ce ceesesseecesesteneeesesrecesscstsesssesuneneecersrasseecesseevansnesetsetesercereeenee 13

Service Panel ........cccssecesesesessssesseessesseesssesseeseesnsesnscaseesneespegeesesessneeserscsnssuecsenessseesaeeensens 14

Game Option Screen.....

Game Option Settings ...........cccccccssususseessesseseesessessessusssssseeseeesceeerseseeseeesutseesneseeesieesnes 16

Tower Service Panel ........sccscsscssesecseessssssecsesseeseesseersessssessecsiesssesecseasarsuesussessessnsseeeeseesee 16

Switch Test Screen

Monitor Remote Adjustment Board

Monitor Adjustment SCreens ........ccecseseeesccsesesescsseneseneeesaneessssaceceescacscreeeseeeststecsnersasieetaee 18

Switch Test Screen — Initialized

Fluorescent Lamp Replacement

Maintenance Door Latches «0.2... scscessscseessesesneessensnseensessacessessesssessstsssecensersnesssssneeenee 21

EMI Cage/ Game PCB Removal........ Replacing Bank Angle (steering) Potentiometer ............::cceccsencs sees 2D Handlebar Assembly ..........:..s::ccssesseseseeseceeseesesceeseeesseeeeessscesseesncessusseeeensuseeensesenasaciceseaes 24 THI. ASSOMDLY..........0ss-cesnssvriniserssbieevivnecttne seecusshe usnvetuiessninvsvognvensediebeesssseesueesstsnienters 24 Spectator Tower Display Assembly (OPeN VIEW) ...........scecss sees eeneestestesteseeatressesseeesserse 2B

Page 7
  • SPECIFICATIONS

POWER SUPPLY:

POWER CONSUMPTION: Game Cabinet Tower (where applicable) MONITORS: Game Cabinet Tower (where applicable)

INSTALLED DIMENSIONS: Two-player Unit Four-player Unit

CARTON DIMENSIONS: Game Cabinet Carton Motorcycle Assy. Carton Marquee Panels Spectator Tower Base Spectator Tower Display

SHIPPING WEIGHT: Game Cabinet Carton Marquee Panels Carton Motorcycle Assy. Carton Tower Base Carton Tower Display Carton

ACCESSORIES:

Note: Specifications may change without prior notice. Modification and/or alteration of the Suzuka 8 hours™ game with kits or parts not supplied by NAMCO may void the warranty. PC XT Type Switching Power Supply

150 Watts 150 Watts

2 standard 25" Color Monitors 1 standard 27" Color Monitor (all with auto degause and remote adjustment boards)

Width Depth Height 79 1/2" 74" 75" 183" 87" 81 1/2"

Width Depth Height 73" 32" 58" 56" 38" 39" 26" 34" 5 3/4" 61" 26" 26" 73" 26" 30"

366 Ibs. 48 Ibs. 183 Ibs. 228 lbs. 285 Ibs.

Keys: (Coin Box) (Coin Door) (Rear Door)... Security Wrench 00... eects esses tssesaeeseeneesteneeee 2 Leg Levelers: (Game Cabinet) .. (Motorcycle Assy (Tower) Numeral Decal Set ........ccsccceseseessssessesseseeseeseeseeese 1 Link Cable o..c..cesceccecsessessssneseessessesessesteseseeeesneneentens 1

Instruction Manual .........c.cscsssecssseesessesesesseesesteeeens 1

Page 8
  • PRECAUTIONS

2-1 Caution when installing This game is designed for indoor use only. The game should not be installed outdoors or under the following conditions: a.

c. In areas directly exposed to sunlight, high humidity, direct water contact, dust, high heat or extreme cold. In locations that would present an obstacle in case of emergency, i.e. near fire equipment or emergency exits. On an unstable surface or floor subject to other vibration.

2-2 Caution when handling/transporting a. b.

c. d

i Do not subject game to physical shock when transporting or moving it. . AC power sources should be via dedicated circuits. The cabinet should be grounded with a securely connected ground plug. . Care should be taken at all times to avoid electrical shock whenever inspecting or adjusting the game, particularly around the video monitor. To unplug AC cords from electrical outlets, grasp the plug, never the cord. Power should always be turned off before replacing any parts or connecting/ disconnecting any connectors. DO NOT attempt to repair the Printed Circuit Boards (PCBs) on site. They contain sensitive chips that could easily be damaged by even the small voltage of a multi-meter. Always return PCBs to your distributor for repairs. Failure to do so will void the warranty. Before moving any assembly, make sure that the leg levelers are in the highest position and the unit(s) rest only on the casters. When moving, separate the game into individual units (Game Cabinet, Motorcycle Assembly, Tower, etc.).

  • GAME COMPONENTS 3-1 Carton Contents The Suzuka 8 Hours™ Game components are packaged in individual cartons, i.e: 1. 2. Game Cabinet Carton - Game PCBs and two monitors preinstalled. Motorcycle Assembly Carton ~ one motorcycle frame and body preattached to the bearing assembly and stand. Two-player Marquee Panel Carton -- one three-piece Marquee Panel for attachment to the cabinet top. Tower Base Carton — one tower pylon, two cross beam support legs, and three filler panels. Tower Display Carton — one display monitor, with LEDs and two back-lighted acrylic graphic panels preinstalled.
Page 9

[namco |

Suzuka 8 hours

Ilustration 3-2, MOTORCYCLE ASSEMBLY

Page 10

prairies

SACKLIGHTED MONITOR BACKLIGHTED IRAPHIC PANEL EZEL GRAPHIC PANEL: BI

—, ____\

Iilustration 3-3, TOWER MONITOR BEZEL AND GRAPHICS

Illustration 3-4, TOWER MONITOR DISPLAY ASSEMBLY

TOWER PYLON

TOWER FILLER ;— PANELS (3 pieces)

TOWER LEGS (2)

a ee ey a

Tilustration 3-5, TOWER PYLON, LEGS AND FILLER PANEL

Page 11

3-2 Game Configuration 3-2-1 Two-player Game with Marquee

NOTE No motorcycle body should be closer than "X" distance (20°) from any obstruction, or 2“X" (40") from a bike on another game unit.

Illustration 3-7, TWO-PLAYER LAYOUT PLAN

Page 12

3-2-2 Four player game with Tower

Illustration 3-8, FOUR-PLAYER GAME CONFIGURATION

(12 2") 146" -— (6'3") 75" LELLLEL LD

  • (14! 8") 176" ——+|
NOTE No motorcycle body should be closer than “X" distance (20") from any obstruction, or 2 “X” (40") from a bike on another game unit.

Illustration 3-9, FOUR-PLAYER LAYOUT PLAN

Page 13
  • INSPECTION The contents of all cartons should be carefully inspected upon receipt to insure that the game is complete and was delivered in good condition. Inspect the game cabinet and other assemblies by doing the following:
  • Examine the exterior of all units for dents, chips, cracks, or broken parts.
  • Unlock and open the game cabinet's coin door and, by reaching inside, release the two (2) latches securing the front service door, and open it. Inspect the interior of the cabinet as follows: a. Verify that all plug-in connectors (on the cabinet harnesses) are firmly plugged in. The connectors are keyed so they fit only in the proper orientation. b. Inspect the power cords to insure that there are no cuts in the insulation. c. Inspect the power supply connectors. d. Inspect the other major sub-assemblies, such as the video display monitors, PCBs, and speakers. Make sure that they are mounted securely and that all ground wires are firmly connected. e. Remove the PCB shipping blocks (2 screws each).
  • Locate the metal shipping brackets on each side of the lower Motorcycle Assembly.
NOTE - These brackets should not be removed until] all connections of the bike and cabinet are complete as detailed in Section 5 (Installation).

4, Examine the contents of the operator convenience pack(s) shipped with the following game units:

Game Cabinet with two Motorcycles Hex Key Wrench, 1/8 CCRAB Torx T-25 Wrench, TMPF 24' RCA Link Cable Number Decal Set, Numerals 1-4 Power Cord

Two-player Marquee Lock Washers, 6/16 Zinc Hex Head Machine Screws, 1/4-20x3/4 Zinc with Lock and Flat Washers and Kep Nuts

Spectator Tower Unit

HHO h Hex Head Machine Screws, 5/16-18x3/4 Zinc with Lock and Flat Washers Hex Head Machine Screws, 1/4-20x3/4 Zinc with Lock and Flat Washers Button Head Machine Screws, 10-24x3/4, Zinc #10 Flat Washers Hex Key Wrench, 1/8 CCRAB 6' RCA Link Cable

Page 14
  • INSTALLATION
NOTE: If installing only individual (two-player) game units, skip the next section and proceed to Section 5-3 on page 10.

5-1 Four-Player Game Installation

You have received a 4-player Suzuka 8 hours game, shipped in 8 cartons. When set up, the game will consist of two 2-player game cabinets with two motorcycles each. The two cabinets will be connected by a set of 4-player center filler panels that will position the cabinets at the proper angle and distance. A seven foot high Spectator Tower with a 27 inch monitor and LED scoreboard will be located above and behind the center panels and the game cabinets. (Refer to page 6.)

  • Remove all assemblies and parts from the eight (8) shipping containers and prepare to assemble them in the intended area of operation.
  • Open the game cabinets, the tower base and the tower monitor cabinet to insure that no connectors or wires have come loose and that no damage has occurred during shipment.

5-2 Spectator Tower Assembly

5-2-1 Assembling Tower Base TOWER PYLON | REARTOWERLEG —

vecteverers @ —O G yy FRONTTOWERLES

faa CASTERS (3)

Mlustration 5-1, ASSEMBLING TOWER BASE

a. Install the Spectator Tower first by attaching the front (shorter) tower leg to the rear leg to form a “T” shape by using the two (2) hex head bolts provided in the monitor tower accessories kit. b. Place the Tower Pylon on it's back and attach the legs with the four (4) hex head bolts from the accessories kit. c. Lift the base upright and move it to where the game will be operated. d. Lower the leg levelers until the rear casters clear the floor.

5-2-2 Attaching the Tower Monitor

a. Move the spectator tower monitor cabinet (Ref. Illustration 3-4, page 4) near the tower pylon and insure that all five (5) connectors in the tower base are below the top, but are still accessable.

Page 15

b. WITH A MINIMUM OF FOUR (4) PEOPLE, lift the tower monitor cabinet and place it on top of the tower base. DO NOT LEAVE THE MONITOR CABINET UNATTENDED AT THIS POINT! c. Line up the bolt holes and secure the monitor with the four (4) bolts from the monitor tower accessory kit. d. Open the back door of the monitor cabinet and connect the five (5) connectors (paying close attention to any lables) from the tower base to the monitor cabinet. e. Secure the back door, raise the leg levelers, move the tower into its final operating position, and then lower both (2) leg levelers until the casters are clear of the floor.

5-2-3 Installing the 4-Player Center Filler Panels

Illustration 5-2, TOWER FILLER PANELS a. Remove the two (2) hex head bolts, near the bottom, from the sides of the game cabinets to be placed together. These bolts will be used to secure the filler panel later. b. Locate the three (3) holes (two on the top and one near the front center) covered by the side decal, and cut the decal to expose the holes. c. Remove the front cover of the lower (L-shaped) filler pane} by removing the four (4) screws securing it to the panel frame. d. Place the filler panel frame on the front leg of the tower assembly and insert one (1) of the hex head bolts (provided in the tower accessories kit) through the bottom back section of the frame into the tower base. DO NOT TIGHTEN the bolt until step (j).

Page 16

e. With the filler panel frame resting on the front leg of the tower assembly, move one of the game cabinets into position next to the frame. f. Use the game cabinet leg levelers to adjust the cabinet until it is parallel to the filler panel and the three (3) holes line up. g. Secure the panel frame to the game cabinet with one (1) of the hex head bolts and the two (2) bolts previously removed from the game cabinet in step (a). h. Secure the upper filler panel to the top, side wall of the same game cabinet, into the holes provided, with two (2) hex head bolts from the accessories kit. i. Move the second game cabinet into position and secure both the lower panel frame and upper panel to it with five (5) hex head bolts. The leg levelers should be used with the second game cabinet in the same manner as in step (f). j. Tighten the bottom back bolt in the lower filler panel frame to the tower base. k. Reattach and secure the lower front cover to the filler panel frame with the four (4) screws previously removed in step (c).

  • Attach the graphic front panel to the upper and lower panels using the four
  • allen head screws, from the accessories kit, securing them into the weld nuts on the panels.

5-3 Attaching the Motorcycle Assembly to the Game Cabinet a. Roll a motorcycle assembly up to the front of the game cabinet. b. Remove the six (6) bolts from the bike base arm (refer to Illustration 5-4). These bolts will be reinstalled to secure the bike assembly.

MOTORCYCLE NUMERAL ASSEMBLY DECAL

MAINTENANCE COVER

GAME CABINET

  • LEG LEVELERS (4) CAB. CASTERS (4) WIRING HARNESS ‘CONNECTORS (15 Pin) FRAME BOLTS (2) — FLANGE BOLTS (4)

Illustration 5-3, BIKE AND CABINET READY FOR CONNECTION BIKE ASSEMBLY LEG LEVELERS (2)

BIKE CASTERS (3) SHIPPING BRACKET (2) FRAME COVER §=——

Page 17

c. Each Motorcycle Assembly has a rectangular flange on the front of its base. (Refer to Illustration 54). A 15 pin connector attached to the motorcycle wiring harness should protrude through the center hole of this flange. If it is does not, gently pull it out with some slack in the harness. If it is not visible, you may have to remove the frame cover over the base arm. d. Matching 15 pin connectors (one for each bike assembly) should protrude from the lower front openings of the game cabinet. If not reachable, open the cabinet service door and reach in to push the connector through the opening. e. Attach the two connectors firmly together.

‘COVER SHOWN rEMOvED FORlARTY

45 PIN CONNECTORS (2)

“FLANGE MOUNTING BOLTS (4)

FRAME MOUNTING BOLTS (2)

Illustration 5-4, BASE ARM CONNECTION

f. Using extra caution to avoid pinching the wiring harness, carefully slide the motorcycle assembly forward so that the front base arm (with flange) slips over the cabinet bracket and is flush with the front surface of the cabinet. Insert the 4 bolts, removed in step (b.), through the holes in the flange, into the cabinet front and secure partially, BUT DO NOT TIGHTEN. g. Insert the 2 bolts, removed in step (b.), through the sides of the seat assembly base arm frame into the cabinet bracket. TIGHTEN SECURELY. h. Tighten the four front flange bolts at this time. i. Repeat the procedure for all remaining motorcycles. j. Adjust the 4 leg levelers on the game cabinet, and extend the 2 levelers on each bike assembly, until all casters are clear of the floor and the assembled unit is level and rests firmly in place.

Page 18

5-4 Two-Player Game — Attaching Marquee (Two-player versions only) When operating Suzuka 8 hours™ as a two-player game, a marquee is supplied (in a separate carton) for attachment to the game cabinet top to add graphic attraction. y Fact dcrs4y F ; PANELASSY. je BOLTS (6) #4 MARQUEE PANEL (top view)

: MARQUEE PANEL GRAPHICS =! GRAPHICS. | —— (Irom)

amco GAME ‘CABINET Sutuka 8 hours

Illustration 5-5, ATTACHING THE TWO-PLAYER MARQUEE To install the two-player marquee panels: a. Bolt the three marquee pieces together using 6 assembly bolts per the diagram. b. Locate the bolts on the top of the game cabinet and remove them. c. Set the marquee support brackets directly on top of, and aligned with, the holes. d. Reinsert and tighten the 4 cabinet attaching bolts.

5-5 Connecting Multiple Game Links When installing more than one Suzuka 8 hours™ game, the units must be linked using standard audio cable. a. Insure that all leg levelers on the game cabinets, motorcycles and monitor tower (if applicable) have all been lowered, and that all casters are clear of the floor. Make sure that all power to the game is turned OFF. b. To link multiple cabinets (24 units), locate the LINK PCB Bracket Refer to Illustration 5-6 on the back of each Game Cabinet, and move all slide switches to the “External” (Right) position.

NOTE: A single cabinet (not linked) must have the slide switch set to the “INTERNAL” (Left) position. If not, the two players will not link.

SLIDE SWITCH SPECTATOR TOWER MONITOR PLUG

Illustration 5-6, LINK PCB BRACKET

c. Using the appropriate diagram from Illustration 5-7, connect the link cables provided from “IN” to “OUT” between each of the game units to be linked. d. To connect the Spectator Monitor, plug the link cable from the monitor into just one (1) monitor connection plug. Only one connection is necessary.

Page 19

ONE GAME TWO GAMES (4 BIKES) (2 BIKES) [OOM ONO} + ONE MONITOR w or ow

THREE GAMES (6 BIKES) + ONE MONITOR

Com Cm com Com

FOUR GAMES (8 BIKES) © ® ©® © © ©© + TWO MONITORS

Illustration 5-7, MULTIPLE GAME LINKS

FOR BETTER OPERATION: Link Cables transmit electronic data between games and are subject to electronic interference. Install the Link Cable as far from other room cables as possible.

5-6 Final Setup and Adjustments a. Remove the power cords from the accessories kits, and apply power to all the cabinets. b. Initialize each motorcycle assembly by releasing all controls, centering the bike, and holding the service switch in while toggling the test switch to “ON”. Once you see “INITIALIZE COMPLETED” on the screen, turn the test switch off. Do this step for all bikes. c. Affix the large bike numeral decals from the accessories kit to the rear of each bike on top of the existing color decals, or on each side of the gas tank. d. The small numeral decals should be affixed in the blank area of the COCA- COLA decals located just above each monitor. These numbers should be placed in the same order as the motorcycle decals. e. Remove the two (2) shipping brackets (one on each side) from the base of each bike, and save them for future use. f. Enter the test mode, and using the Option Screen, set the rank, number of laps, and grid locations (bike number) for each unit (Ref. Section 6-3-2, Game Option Screen, for more information).

NOTE: Each bike must have a different grid number for proper operation. g. Using the service switch, advance to the switch test screen and insure that all controls and potentiometers are operating properly. h. Ifa spectator tower is installed, remove the tower side door, turn on the test mode and insure that the game settings match with those on the game units. If changes need to be made, refer to Section 6-3-3. i. Play the game to check for proper operation.
Page 20
  • ADJUSTMENTS/TESTING

6-1

6-2 Power Switch

The on-off switch is mounted on the inside rear wall of the game cabinet and is accessible from both the inside and the outside of the game.

Adjustment Switches on the Service Panel Open the coin door to locate the Service Panel. There are duplicate switches and control knobs for each player position — left and right — and they must be adjusted separately.

LEFT PLAYER RIGHT PLAYER

‘o) j |_ VOLUME CONTROL H CABINET SPEAKERS L Roto R : | _ VOLUME CONTROL BIKE SPEAKER ON ON = | — TEST SWITCH : © (togale) j OFF

RIGHT PLAYER COIN COUNTER

Illustration 6-1, SERVICE PANEL SERVICE SWITCH (push button)

LEFT PLAYER COIN COUNTER

a. Test Switch

Toggling this switch “ON” enters the test mode for the appropriate player. This is where the self-tests are performed, and game variables (including pricing, level of difficulty, number of laps per game etc.) are set/changed. Tur the test switch to the “OFF” position at any time to return to the attract mode, b. Sound Volume Control (Cabinet Speakers) These volume controls are used to set the volume of the left and right speakers located above each monitor. c. Sound Volume Control (Motorcycle) This control is used to set the volume of the speaker located in the gas tank of each motorcycle. It is suggested that the volume of this speaker be set a bit louder than the volume of the cabinet speakers for best effect. d. Service Switch This switch is used to step through the various game option and test screens and for service credits. It will not advance the coin counter when it is pressed.

Page 21

6-3 Test Mode Suzuka 8 hours™ automatically conducts a self test during the first few seconds when the power is turned on. Additional tests can be performed manually.

6-3-1 Test Mode Open the coin door and flip the Test Switch to the “ON” position. The Game Option Screen will be displayed on the appropriate monitor.

Various tests are displayed sequentially by pressing the service switch to advance through the five (5) test screens. The test switch can be turned off at any time to return to the attract mode.

6-3-2 Changing the Game Settings (Game Option Screen) The Game Option screen is used to change the game fees, etc. The Game Option Screen is the first screen in the test mode.

NOTE: The setting for RANK, NUMBER OF LAPS, and WAIT TIME must be the same for all connected machines for the game to function properly. This includes monitor tower settings. (Ref. Sec. 6-3-3).

GAME OPTIONS COIN 1 MECH 1 COUNT 1 COIN COIN 2 MECH 1 COUNT 1 COIN GAME COST 2 COINS 1 CREDIT BONUS COIN NONE — FREE PLAY NO ——__—_ RANK LAP GRID NO. CAR TYPE BLACK/GREEN LINK ON 2 WAIT TIME C SOUND TEST 1 Hi SCORE INITIALIZE? NO

Illustration 6-2, GAME OPTION SCREEN

Make all changes referring to the Game Option Settings. (Illustration 6-3, Game Option Settings).

Turn the throttle of the appropriate motorcycle to select the item to be changed. Squeeze the brake to make the change.

When changes are completed, press the Service Switch to advance to the next screen, or turn off the Test Switch and the monitor will return to the attract mode.

Page 22

TABLE OF GAME OPTION SETTINGS (<1 standard setting)

CONTENT

(a) | COIN 1 MECHCoin count per one coin1-9 (original setting is 1)
(b) | COIN 2 MECHCoin count per one coin1-9 (original setting is 1<1)
  • | GAME COST Coin count required for one game (1 credit) | 1-9 3 2 player version) (3<] 4-8 player versions)
(d) | BONUS COINEnter "X" number of coins to gainNONE <

*X* bonus coin(s). INSERT BONUS 2-9COINS 1-3 Coins

  • | FREE PLAY No <4 YES ) | RANK (difficulty) A (easy) to D (hard) (B<] original setting)
  • | LAP 3t06 (4<{ original setting) (hy | GRID No. |—to—8 Match with the number of the connected motorcycle (motorcycle number) No BIKES should have the same Grid #.
  • | CAR TYPE Changes the colors of the motorcycle. @ | LINK Normal when ON. (The numeral is the number of bikes connected together).
  • | SOUND TEST Used to test sound effects. () | WAIT TIME A (shor) to D (long) (C-<1 original setting)
  • | Hi SCORE INITIALIZE? No < YES — Erases all high scores

Illustration 6-3, GAME OPTION SETTINGS

6-3-3 Spectator Tower Options Screen The Spectator Tower operates with an independent PC) the tower assembly. B located in the base of

VOLUME CONTROL TOWER SPEAKERS L R ON

OFF }-- TEST SWITCH |_SERVICE SWITCH (push button)

(toggle)

Illustration 6-4, TOWER SERVICE PANEL Remove the side door and turn the test switch on to see the current settings. If changes need to be made, follow these steps: a. Insure that the power to the tower unit has been turned off. b. Open the PCB enclosure by removing the six (6) phillips head screws and slide the logic board toward you. c. Locate DIP switch 8 on the corner of the PCB next to the small edge connector and turn it “ON”. This puts the logic board into the automatic test mode. d. Replace the PCB into the enclose and turn the tower unit on. e. Turn the test switch on the tower service panel to the “ON” position. The Game Options Screen should be displayed on the monitor. f. To select the item to change, quickly flip the test switch OFF and back ON.

Page 23

g. Tochange the selected item, press the service switch until the desired option is displayed. h. Turn the service panel test switch to “OFF” and remove power from the monitor tower. i. Return DIP switch 8 to its original “OFF” position. j. Power up the spectator tower and use the service panel test switch to check your settings. To advance to the next screen, press the service switch. 6-3-4 Switch Test Screen (2nd test) This screen is used to test for proper operation of all switches and potentiometers.

SWITCH TEST DIP sw 12345678 - (a) TEST SW (b) COIN 1 SW (ce) COIN 2 SW (d) BANK (e) THROTTLE + BRAKE (9)

Illustration 6-5, SWITCH TEST SCREEN

  • Displays the status of the option switches located on the game PC board (CPU-PCB). If “ON”, the numbers corresponding to the option switches are red. This function is also displayed on the monitor tower test screen.
  • Always should be displayed red. This function is also displayed on the tower monitor.
  • When the LEFT (Coin 1) switch is triggered, a red “ON” will be displayed and the number will increase.
  • When the RIGHT (Coin 2) switch is triggered, a red “ON” will be displayed and the number will increase.
  • The following is displayed when testing the motorcycle potentiometer: + When the motorcycle is in the upright position, “OO CENTER” is displayed. ¢ When the motorcycle is tilted to the left, “LEFT” is displayed. The further it is leaned left, the more the number will increase and “OK” lights indicating maximum left lean.
  • When the motorcycle is tilted to the right, “RIGHT” is displayed. The further it is leaned right, the more the number will increase and “OK” lights indicating maximum right lean.
Page 24
  • When the throttle grip is turned counterclockwise, the numerical value changes, and “OK” is displayed when the value reaches “80” or more.
  • When the brake lever is squeezed, the numerical value will change, and “OK” is displayed when the value reaches “20” or more.

6-4 Monitor Adjustments eeentantantentent <Yecrccurstrrtyctraty \atrt'<r pleetenlententonionton

DANGER HIGH VOLTAGE ! THE MONITOR CONTAINS LETHAL HIGH VOLTAGE. THE MONITOR IS !

L TO BE SERVICED BY A QUALIFIED SERVICE TECHNICIAN ONLY.

The monitor remote adjustment controls (illustration 6-6) are located in the rear of the cabinet and, at operator option, can be mounted near the front service door. The Spectator Tower monitor controls can be accessed by removing the right side graphic panel. OQ ‘aM O

i)©>
VR 103VR 102VR 101

»)» ~) »

VR 106VR 105VR 104

TOP ROW-LEFTTO RIGHT BOTTOM ROW- LEFT TO RIGHT VR'103 - VERTICAL POSITION VR 108 - HORIZONTAL POSITION VR 102 - BLACK LEVEL VR 105 - VERTICAL HOLD VR 101 - CONTRAST VR 104 - VERTICAL SIZE

Illustration 6-6, MONITOR REMOTE ADJUSTMENT BOARD

There are three (3) monitor test screens:

CROSS HATCH CROSS HATCH with WHITE BLOCK COLOR BAR

Illustration 6-7, MONITOR ADJUSTMENT SCREENS

6-4-1 Cross Hatch Pattern

To center cross hatch pattern: + Use VR 103 (V-POS) to adjust cross hatch UP or DOWN.

  • Use VR 106 (H-POS) to adjust cross hatch LEFT or RIGHT.
Page 25

6-4-2 Cross Hatch Pattern with White Block Adjust

White block adjustment should not be necessary — just insure that block is centered in the cross hatch, and is white. If it is not, call a qualified Service Technician, or NAMCO Customer Service.

6-4-3 Color Bar Test

Color should not need adjusting, but if the white fade test (the bottom white bar) is tinted an off color, adjustment can be made with the appropriate color gun adjustment on the CRT neck board by a qualified Service Technician.

6-5 Adjustments When Replacing Parts (Initialization) When replacing the game PCBs, the motorcycle bank, throttle, or brake potentiometers, be sure to follow the procedures below. If not done, the game may not function properly. a. b. Open the coin door. Release the throttle grip and brake lever so they are in their “netural” positions. Make sure the motorcycle is in the upright (centered) position. For accurate settings, it is recommended that one person hold the bike upright, while another person performs the remaining steps. If working alone, the shipping brackets can be temporally reinstalled to accomplish this. Press and hold the Service Switch down, while toggling the Test Switch to the “ON” position. Adjustment is completed when “INITIALIZE COMPLETED” appears on the bottom of the Switch Test Screen. Turn the test switch “OFF” to return to the attract mode.

SWITCH TEST DIP SW 12345678 TEST SW ON CcOIN1 SW OFF 00 COIN2 SW OFF 00 BANK 00 THROTTLE 00 BRAKE 00

INITIALIZE COMPLETED

Illustration 6-8, SWITCH TEST SCREEN - INITIALIZED

Page 26

HOW TO PLAY

¢ Suzuka 8 hours™ is a motorcycle racing game modeled on the famous Suzuka Circuit that allows players to compete against time and/or each other.

  • Four sets of two-player games can be interconnected, so that up to eight (8) players can race simultaneously.

+ Players manipulate their motorcycles independently by using the throttle grip, brake lever, and leaning left or right to steer (just like a real bike). The object of the game is to cross the finish line first within the time allowed, while avoiding a crash with opponents motorcycles and/or computer-controlled bikes.

+ After a player inserts the proper coin(s), an entry prompt appears on the screens in front of any empty seats displaying a message urging others to enter. Additional players can enter the race by inserting the proper coin(s) within 20 seconds (operator adjustable). One person can always play if no others enter that particular race.

  • Once all the players have entered the game, or if the entry time passes, the timer counts down “3-2-1”, and the race starts with a “GO” sign.

+ A Spectator Tower, located between and above every other game unit, is incorporated into any game featuring 2 or more players. This allows bystanders to enjoy the thrills and excitement of the race, and be encouraged to participate in additional races. Each racer's position is shown on a map display.

+ The race continues until the timer counts down to zero. Any player to successfully complete a lap before the timer hits “0” extends the game time for all players.

+ After completing the preset number of laps (operator adjustable), players cross the finish line to the thrill of a checkered flag.

+ When players reach the finish line or time runs out, racing statistics, including the player's ranking and lap times, are shown. When a player wins a race in which two or more persons are entered, a Championship Celebration is shown on their monitor.

+ Ifa player finishes first, and is in the top 15 of the latest 500 winners, his/her initials can be entered by rotating the throttle grip to select a letter and squeezing the brake lever to enter it.

¢ Allinitials entered are saved on the individual players’ screens, as well as on the spectator monitor, until erased by using the Game Option Screen. (Ref. Sec. 6-3-3)

Page 27
  • MAINTENANCE Be sure to turn the power off before conducting any maintenance procedures.

8-1 Game Cabinet Assembly

8-1-1 Replacing the Fluorescent Lamp/Starter

ACRYLIC CENTER PANEL ;>——— BEZI Ty) —[fremee |

MONITOR BEZELS (2) ‘——-MONITOR BEZELS (2) le} jd loin SPEARERS (4)

MONITOR RETAINING BRACKETS (2)

Illustration 8-1, FLUORESCENT LAMP REPLACEMENT

a. Remove the four (4) bolts holding the center acrylic graphic panel in place. Remove it to expose the fluorescent lamp and starter. b. Remove and replace the bad fluorescent lamp or starter.

8-1-2 Opening the Maintenance Door

REACH THROUGH COIN DOOR TO ACCESS LATCHES

LATCHES MAINTENANCE (inside) DOOR

LATCH

MAINTENANCE DOOR

IDustration 8-2, MAINTENANCE DOOR LATCHES a. Open the coin door. b, Unlatch the two latches located inside the left back of the maintenance

door.

8-1-3 Replacing the Fuse(s) a. Open the maintenance door(s). b. Replace the fuse on the power base. Make sure to use the specified fuse values; 3A for the game cabinet and 3A for the tower.

Page 28

8-1-4 Removing the EMI Cage a. Open the maintenance door. b. Insure that the PCB shipping blocks have been removed. c. Remove the edge connectors (2 pieces) from the EMI board. d. . To remove the ground terminal, remove one (1) phillips head screw from the EMI Board. e. Remove the one (1) finger nut from the top center of the PCB retaining bracket.

f. Slide out and remove the EMI Cage.

BEHIND 4 1K MAINTENANCE DOOR: | 7 EDGE AINTENANC| | fe \ F CONNECTORS (2) 4 \

GAME PCB BOARDS (2) POWER SUPPLY ind at FUSE LOCATION EMI RETAINER EM! BCARD

Illustration 8-3, GAME PCB REMOVAL

Removing the Game PC Board a. Open the maintenance door. b. Insure that the PCB shipping blocks have been removed. c. Remove the edge connectors (2 pieces) from the EMI Board. d. . Remove the six phillips head screws (M4 x 10), and remove the EMI Board and the EMI retainer. e. Pull the game PCBs (2 pieces) and the EMI Board carefully toward you and remove them.

Removing the Monitor Assembly ltentaeteslamter oy ertestca ste tecthcc tw lente loatanoatoalo

DANGER HIGH VOLTAGE | THE MONITOR CONTAINS LETHAL HIGH VOLTAGE. THE MONITOR IS |

LL, TOBE SERVICED BY A QUALIFIED SERVICE TECHNICIAN ONLY,

Open and remove the rear door of the Game Cabinet. Disconnect the two connectors from the Monitor Assembly. Remove six screws securing the monitor bezel and remove it. Remove the four bolts (1 each corner) securing the plywood base to which the monitor is bolted.

e. Slide the monitor (with board attached) forward and out. aos Pp

Page 29

8-2 Motorcycle Assembly

8-2-1 Replacing the Bank Angle (steering) Potentiometer

SET SCREW POT. BRACKET. POTENTIOMETER

PHILLIPS SCREWS (4)

(Me X10)

Illustration 8-4, REPLACING THE BANK ANGLE POTENTIOMETER

a. Remove the four (4) bolts and remove the access cover on the lower rear of the Motorcycle Assemble. b. Write down the color order of the wires (i.e 1=yellow, 2=white/blue, 3=white etc.) and desolder the potentiometer harness. c. Remove the four (4) screws holding the potentiometer bracket, and remove it. d. Remove the potentiometer from the bracket and replace it with a new one.

NOTE: When remounting the potentiometer, position the gear so that its screw faces the same direction of the terminals of the potentiometer, when the motorcycle is in its neutral (upright) position.
Page 30

8-3. Handlebar Assembly

8-3-1 Removing Handlebar Assembly Cover The handlebar assembly cover is removed by unscrewing the four security bolts using the special driver in the accessories kit. This is required to access the throttle and brake potentiometers, as well as to remove the throttle assembly.

SECURITY BOLTS (4)

BRAKE LEVER

HANDLEBAR COVER O C

oa [— THROTTLE GRIP SIDE COVER

Illustration 8-5, HANDLEBAR ASSEMBLY

8-3-2 Replacing the Throttle Potentiometer

ce) BOLT (MS x 12)

  • NUT (Ms) POTENTIOMETER

BRAKE. POTENTIOMETER BRACKET ALLEN HEAD SCREW (M4 x 8)

  • omeng° Pa x & co)

SIDE COVER

POTENTIOMETER

THROTTLE POT. BRACKET SCREWS (2) (M5 x 8) SPRING SUPPORT/ SPACER ROD GEAR

Idustration 8-6, THROTTLE ASSEMBLY

Page 31
NOTE: Remove Handlebar Assembly Cover. (Ref. Sec. 8-3-1) Remove the two phillips head screws (M5 x 8) retaining the throttle potentiometer bracket just above the throttle shaft, and remove the bracket Write down the color order of the wires and desolder the potentiometer harness. Remove the potentiometer from the throttle pot. bracket and replace it with a new one.

When remounting the potentiometer, position the gear so that the potentiometer shaft does not restrict the movement of the throttle. Failure to do so can destroy the potentiometer.

8-3-3 Replacing the Brake Potentiometer a. b. Remove Handlebar Assembly cover (Ref. Sec. 8-3-1). Remove three Torx bolts (M5 x 12) holding the side cover and the allen head screw (M4 x 8) through the end of the spring support rod. Remove the side cover and slide out the throttle assembly. . Remove nut (M5) and bolt (M5 x 12) holding the brake potentiometer bracket, and remove it. e. Remove the potentiometer harness.

NOTE: Remove the brake potentiometer from the brake pot. bracket and replace it with a new one.

When remounting the potentiometer, position the gear so that the potentiometer shaft does not restrict the movement of the brake. Failure to do so can destroy the potentiometer.

8-3-4 Removing the Throttle Assembly a. b. Remove Handlebar Assembly cover (Ref. Sec. 8-3-1). Remove three Torx bolts (M5 x 12) holding the side cover and the allen head screw (M4 x 8) at the end of the spring support/spacer rod. Remove the side cover and slide out the throttle assembly. . When replacing the throttle assembly, be sure to have the spring arm above the spring support/spacer rod or the throttle will not return to the neutral position when released. Resecure the side cover and handlebar cover by reversing the steps described above.

Page 32

8-4 Spectator Tower Assembly

8-4-1 Changing Tower Fluorescent Lamps and LEDs

SPEAKER GRILL. SPEAKER GRILL, RETAINING SCREWS (4) {2 each sito)

ACRYLIC MONITOR BEZEL— GRAPHIC PANELS (2) Left and Right

TOWER SPEAKERS (2) FA

a FLUORESCENT TUBES (3)

  • LED DISPLAYS (2) MONITOR RETAINING CLEATS (3)

Illustration 8-7, SPECTATOR TOWER DISPLAY ASSEMBLY

a. Remove the five (5) screws securing each backlighted acrylic end panel to the display cabinet and set aside. b. Remove and replace failed flourescent tube(s) or starter(s). c. Remove and replace failed LED unit(s).

8-4-2 Replacing Spectator Tower Monitor ssc

DANGER HIGH VOLTAGE | THE MONITOR CONTAINS LETHAL HIGH VOLTAGE. THE MONITOR IS : L TO BE SERVICED BY A QUALIFIED SERVICE TECHNICIAN ONLY.

a. Remove the five (5) screws securing each backlighted acrylic end panel to the display cabinet and set aside. b. Remove the four (4) screws securing the tower monitor bezel and lift forward and down. c. Remoye the three (3) wood cleats (2 screws each) that hold the monitor bezel in place. d. Open the rear door of the monitor cabinet, and loosen the two guide brackets. e. Disconnect the monitor chassis wiring harness connectors. f. Carefully slide the monitor assembly forward and out rhe front of the cabinet.

CAUTION: Because of the monitor's weight and elevation, this procedure should be performed by two or more persons.
Page 33
  • TROUBLESHOOTING — GENERAL If you suspect the game may be malfunctioning, the following steps should be taken before a service request is made.
  • The power supply should be between 110-120 Volts AC. However, when some other equipment (air conditioner, multiple pinball games, air compressors, etc.) are connected to the same power supply, the voltage may change beyond this range and cause game trouble or improper operation. Each cabinet should have its own dedicated. power source.
  • When the game does not work with the power turned on, turn the power off for about ten (10) seconds, and then back on. This may restart the game. If it still does not work, inspect the fuses. (Ref. Sec. 8-1-3 Replacing Fuses)
  • When the game PCB, the Motorcycle Bank Angle, Throttle, or Brake Potentiometers are replaced, it is necessary to initialize the CPU for normal operation. Make the appropriate adjustments by referring to Section 6-5, Adjustment when replacing the parts (Initialization).
  • Check all wiring connections as malfunctions can be caused by loose connections.
  • Foreign substances on the game PCB or on the monitor PCB, or dust may cause malfunctions or improper operation. Check that the PCB enclosures are clean.
  • When you make electrical checks, use the wiring diagrams for reference.
  • If the above suggestions are not applicable, or no improvement is observed, contact your distributor or the service office printed on the back cover of this manual.
  • DO NOT ATTEMPT TO REPAIR THE GAME PCB YOURSELF. Instead, please return the board to your distributor for any repairs. This PCB contains sensitive chips that could be destroyed even by the internal voltage of a multimeter.
  • When sending parts to be repaired, make sure to pack them firmly with a complete explanation of the problem. When sending PCBs, package them in anti-static foam or bubble wrap, and pack them in cardboard boxes to protect against impact damage during shipment. To ship monitors, pack them in wooden frames so that CRTs and PCBs are protected against excess load.
Page 34

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 35

Parts List

Page 36

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 37

10-1 Motorcycle Assembly

l © @

  • (19)

MOTORCYCLE ASSEMBLY eM | DESCRIPTION PART NO. ITEM DESCRIPTION "| PART NO.

+ | _ Frame, Metal MotorcycleEH10-00782.7]Gas TankEH190-00895-00
21Frame, PedestalEH10-00842-0018F GearEHO09-261-234
3MastEH09-261-219 _|19Motorcycle Side, RightEH90-00640-00
4 | ShaftEHO9-261-22019 | Motorcycle side, LeftEH90-00640-01
| 5 | Stopper HousingEHo9-261-22120 |Stopper Rubber~ | eHo9-261-237
@_|_Gycle Speaker PlateEH10-00839-00[21 |Assembly, Handle BarEHO3-00871-00
7IDiamond Plate__ [eH 0-00843-0022Shipping BracketEH10-00841-00
8[Pedestal Cover PlateEH10-00844-00zoStopper SpacerEH09-261-248
8 _|Spacer_| prers|[24Pitow Unit woP207EH09-261-261
10Potentiometer Holder BracketEH10-00840-0025Rubber Spring OR-S 27X100.EH09-261-262
i1_|__Volume Bracket (V)EH09-261-22726 |Spur Gear $758258+0306EHo9-261-263,
12Rosta BracketEHO9-261-22827Caster, Swivel 160-3VG24-00783-00
13.| _ Brkt. ABS Cover #2aera28 |_Leveler, Leg‘VG20-00095-00
14Brkt. ABS Cover #5| EH10-00896-0029|SpeakerVG54-00172-00
15_|_Brkt, ABS Cover #1EH10-00869-00@_| Volume EWSUOAFZ0ES3'$G08-008.006
16 |Brkt, ABS Cover #3EH10-00885-0031|_HiteceEHO3-00670-00
Page 38

10-2 Throttle/ Brake Assembly

suas

THROTTLE and BRAKE ASSEMBLY

ITEMDESCRIPTIONPART NO.ITEMDESCRIPTIONPART NO.
1Brake Upper PlatoEH09-261-31310 | Grip Base (R)EHO9-240-102
&Throttle Volume BracketEHO09-261-314nNThrottle SpringEH09-240-116
3Brake Volume BracketEHO9-261-31512 |Brake GearEHOS-240-117
4Collar (A)EHO9-261-31613_|Brake Volume Gear| EH09-240-118
5Collar (B)EHO9-261-31814Stopper LODEHO9-240-122
6Throttle StopperEHO9-261-31815 | _ Spring SpacerEHO9-240-124
7Slide PlateEHO9-261-31916‘Spur Gear SIS 24B+0806EHO9-240-126,
8Brake SpringEH9-261-3227Micro Switch SS-5GL13EH09-000-054
9Brake StopperEnorertses |18 |Volume EWSUOAF20E53EHO9-008-006
Page 39

10-3 Handle Assembly — EH03-00671-00

HANDLE ASSEMBLY | {rem | DESCRIPTION PART NO.

1Handle BaseEHO09-261-311
2CoverEHO9-261-312
3Handle CoverEH09-261-320
4TachometerEH09-261-321
5Grip RubberEHO9-240-104

6 _|__Brake Lever EH09-240-105

Page 40

10-4 Parts List

ASSEMBLY MOTORCYCLE EH05-00848-00 [ASS¥. MOTORCYCLE MONITOR CABINET EHO05-00845-00

(TEMDESCRIPTIONPART NO.ITEMDESC!PART NO.
1_[Assembly, Handle BarEH03-00671-00 | |_1_|CabinetEH63-00802-00
2_|Cover, Handle Bar ABSEHO9-261-3122_|Monitor, 25°, YBaVGB5-00042-00
3_|SpeakerV@54-00172-003 _| Transformer, 3PBBEVG56.00174-00
4 _| Cover, Speaker ABSEH190-00662-004| Speaker, ShieldedVG54-00753-00,
|Namco Volume AssemblyEHO3-00672-005 _| Speaker Grill‘VG10-00485-00
@_|Access PanelEH190-00697-006 _| Plate, Door LockVG10-00446-00
7_|Frame, Metal MotorcycleEH10-00782-007_|Hinge, Front DoorEH19-00816-00 |
8 | Cycle Speaker PlateEH10.00809-008_|Chassis, FloorEH69-00817-00
9_|Potentiometer Holder BrktEH10-00840-009_|Front Door Latch BracketVG13-00818-00
10_|ABS Holding Brackets£H10-00869-00 | | 10 | Audio PCB BracketEH19-00819-00
11 _| Shipping BracketEH10-00847-00 | |11 | Monitor Top GoverEH10-00820.00
12 _| Cover, Motorcycle ABS, Right€H90-00640-00 |[412 _| Link BracketEH10-00821-00
13_|Cover, Motorcycle ABS, LeftEH90-00640-01 | | 13 | PCB Suppor Bracket| EH3-00822-00
14_|Seat, Plastic FormedEH90-00696-00 | | 14 | PCB RetainerEH70-00823-00
15_|Light, Rear Plastic Formed£H90-00701-00][15 | UL Ground Bracket‘VG10-00801-00,
16 | Hit PCBEH03-00670-00 |[16 | Decal, Sidewall LogoEH40-00812-00
17_|Edge, TWhiteVG90-00757-00

18 _| CRT Bezel, Right EH90-00698-00,

ASSEMBLY, SHIPPING BOX MOTORCYCLE19_|CRT Bezel, LeftEH90-00878-00

20 _| Decal, Monitor (Coca Cola) EH40-00772-00

TemDESCRIPTIONPART NO.31[beck Dooryao6-00867-00
1__|Box, Shipping, MotorcycleEH60-00784-00 | | >tSang BenelerIe0.00605-00
2 _| Label, Shipping, Nameove44-00151-00|1351pispiay Panol ah Conorucourss
3 _| Label, "Motorcycle"Vo46-00785-00 |[4 | Clamp, HRT Overcenter ZN‘VG78-00824-00
4 _| Shipping BagNG60-00152-00 |35 | Fan, Axial 80 CFM‘VG55.00060-00
5 _| Checklist, OCEH00-00805-00 |[25 | Soreen, Fan wiHoles6x6VG55-00061-00
& _| Label, Serial #MEH 00706-00:27 _| Power Supply, XT 150W P. Chou‘VG88-00173-00
28_|Relay PCBEHO3-00668-00
29_|Fixture, Fluorescent 18°VG57-00058-00
‘ASSEMBLY, MOTORCYCLE MONITOR SHIPPING30| Lamp, FISTeGWyae7a00600
TEMDESCRIPTIONPART NO.31_|Enclosure, Coin HousingVG10-00465-00,
1 | Box, Shipping Motorcycle Monitor| EH60-00765-00 | | 92 _| Housing,Coin No Enel., WhiteH70-00796-00 |
2 _| Label, Shipping Namcov@a400151-00||33 | Box, PlasticGash‘vG83-00088-00
3_|Label, "Cycle Monitor Cabinet”EH46.00767-00|| 34 | Counter, Goin¥GB3-00090-00,
4__|Shipping BagVG60-00152-0035 | PCB, 8 Hours MotorcycleEHO3-00667-00
8_|Service ManualEH45-00832-00 | | 36_|Housing, FerriteVG76-00199-00
6 _| Schematics, Right—H45-00833-00 | | 37 _| Bead, FerriteVG76-00198-00
7_|Schematics, Left£H45-00634-00 | | 38 | UL Fuse Label, 1 AmpVG46-00809-00
@_|Label, FBI‘Ve44-00150-00| 39 | UL Fuse Replac. Caulion LabelVG44-00826-00
9 _| Label, Serial #‘ve44.00795-00|| 40 | Caster, Swivel 160-3VG24-00783-00
10 | Checklist, ACEHO0-00835-0041_|Leveler, LegVG20-00095-00
1t_|Label, FOCvea6-00031-00|| 42 | Fuse HolderVG67-00827-00
12_|Cover, Serial #va95.00836-00|| 43 | Fuse,1AmpVG52-00804-00
13 | Label, ULvea6.00065-00|| 44 | Fasteners| Ve@20-00828-00
Page 41

10-4 Parts List

[EH PLASTICS KIT (Motorcycle) EH0S-00846.00 ~_] [NAMCOLTD. EXPORT KIT EH05-00674-00

ITEMDESCRIPTIONPART NO.ITEMDESCRIPTION|_PART No.
1Motorcycle Side Panel, RightEH90-00640-00 | | 1 | Game PCBx2EHO3-00667-00
2_| Motorcycle Side Panel, LeftEH90-00640-012 | Relay PCBx1EH03-00668-00
3_|Gas TankEH90-00695-00=2CHPCB x2EH03-00668-00
4 | SeatEH90-00606-004|HitPCBx2EHO3-00670-00
5 _ | Access PanelEH90-00697-005_|Namco Handle Assy.EH03-00671-00
6| CRT Bezel, RightEH90-00698-006 _| Namco Volume Assy.EH03-00672-00
7 | CRT Bezel, Lett| EH90-00878-007__| Bearing Assy.EHO03-00673-00

8 | Blank Bezel _| £H90-00699-00 9 | Tail Light EH90-00701-00

EH GRAPHICS KIT EH05-00847-00 __] [ ASSY., MOTORCYCLE PEDESTAL EH05-00849-00 ITEM DESCRIPTION PART NO.

1_|Decal, Motorcycle Side, RightEH40-00769-00
ITEMDESCRETIONPARTNO. |[2 | Decal, Motorcycle Side, LeftEH40-00764-00
1_|Frame, Pedestal___} EH10-00842-003_|Decal, Motorcycle # Set 1-4EH140-00766-00
2 _| Diamond PlateEH10-00843-004 | Decal, Moteraycle Logo (Namco)EH40-00760-00
3 _| Pedestal Cover PlateEH10-00844-00=lbecul cebwiet topa(caea cash| Exananr7ao0
4_| Caster, Swivel 160-3VG24-00788-00= | besalepen eatena00077500
5 _| Leveler, Leg\G20-00095-007_|Display Panel, Cabinet, CenterEH40-00775-00

@ | Decal, Cabinet, Right Side £H40-00770-00 9 | Decal, Cabinet, Left Side £H10-0077100 | [10 | Decal, 2° Marquee, Fight EH40-00776-00

11_|Decal, 2P Marquee, LeftEH40-00777-00

12 _| Decal, 2P Marquee, Center EH40-00778-00

METAL MARQUEE EH05-00814-00__ |73tower ig EwerEason 2000 |
ITEMDESCRIPTIONPART NO.14_|Tower, Lelt PanelEH40-00787-00
1__|Metal Marquee PanelEH10-00815.00 |[15 _| Display Panel, 4P, CenterEH40-00779-00
2 _| Decal, 2P Marquee, Right£H40-00776-00|| 16 "| Decal, Motorcycle Set # 58EH40-0076800 |
3 _| Decal, 2P Marquee, Left£Fi40-00777-00 |[47 _| Decal, Logo Set #58EH40-00774-00
4 _| Decal, 2P Marquee, CenterEH40-00776-00 |[18 | Decal, Namoo Logo, SideEH40-00812-00 |
Page 42

10-4 Parts List

ASSEMBLY SPECTATOR MONITOR CAB, EH05-00838-00 ASSEMBLY, TOWER EH05-00825-00

ITEMDESCRIPTIONPART NO.{TEMDESCRIPTIONPART NO.
1_|CabinetEH63-00790-001_|PCB, TowerEHO3-00786-00
2_|Edge, T WhiteVGS0-00757-002__|Tower Metal StandEH10-00810-00
3_|Bumper RubberEH06-00856-003__|Tower, Fan SaeenEH10-00850-00
4_|Fixture, Fluorescent 18"VG57-00058-004_|Fan Holder BracketEH10-00851-00
5_|Lamp, FIsTEGWVG57-00058-005 _| Power Supply TrayEH10-00852-00
\~6_|Speaker, ShieldedVG54-00753-006 _| Beam, RightLettEH10-00853-00
7_|Monitor, 27°, Base MountVG85-00798-007_|Beam, Fronv/BackEH10-00864-00
8 _| Tower BezelEH90-00662-00& | Tower DoorEH63-00855-00
9. | Monitor Holddown BracketEH10-00859-009 _| Rubber BumperEHO6-00856-00
10 _| Monitor Support BracketEH63-00860-00 | | 10 | Lock,1Key~_| WG26-00857-00
11_|Screen, Back Door[eH10-00871-00 |[11 _| Fuse HolderVG52-00629-00
12_|Screen, Speaker wiLogo€H10-00872-00 | | 12 | UL Fuse Label, 2 Amp\VG44-00796-00
13_|Bracket, Trim, OutsideEH10-00873-01 | | 13 _| UL Fuse Replac, Caution LabelVG44-00826-00
14 | Bracket, Trim, InsideEH10-00874-00 | | 14 | Fuse,2 AmpVG52-00797-00
18 _| Plate, Door LookvGr0-00446-00 |[15 _| Transtonmer, PBB‘VG56-00174-00
16 _| Bracket, Right ScoreEH10-00861-00 | | 16 | Cabel MountEH13-00858-00
17_|Bracket, Left Score€H10-00862-00 | | 17 | GrommetEH95-00870-00
18 _| LED, ScoreEH03-00791-00 | | 18 | Fan, AxialVGS55-00060-00
19. | Tower Acrylic PanelEH90-00739-00 | | 19 | Power Supply, XT 150W P. ChouVG88-00173-00
20 _| Tower Acrylic PanelEH90-00793-00 |[20 | Caster, Swivel 160-3VG24-00783-00
21 _| Box, Shipping, Spectator TowerEH60-00792-00 | | 21 | Leveler, Leg‘VG20-00095-00
22 _| Label, Shipping, Namcove44-00151-00 |[~22_|Box, Shipping TowerEH60-00787-00

23 _| Label, “Spectator Monitor Cabinet” | EH44-00863-00 | | 23 _| Label, Shipping Namco VG44-00151-00

24_|Shipping BagVG60-00182-00 | | 24 _| Label, “Tower Stand”EH46-00789-00

[ 25 _| Service Manual, Spec. Monitor Cab. _| EH45-00864-00 | | 25 | Shipping Bag VG60-00152-00 26 _| Schematics, Tower EH45-00865-00

27_|Label, FBIVG44-00150-00
28_|Label, Serial #v@a4-00795-00 | [ ASSY, MIDDLE CONN. UNIT (Filler Panel) EH05-00886-00
29 _| Checkist, OCEH00-00895-00 |TiremDESCRIPTIONPART NO.
30 _| Label, FOCWG46-00051-00 ||ifidale Connector Base FrameEH10-00875-00
=~cover cenitwe2__|Middle Connector Top FrameEH10-00876-00
33 | Leck, DoorKey*va26.00857-003__|Middle Connector Bottom PanelEH10-00877-00
34 | Fasteners‘WG20-00828-00aa Payeraee:e190-0073800 |

5 _| Display Panel, 4 Player, Center £H40-00779-00 35 | Assy., Wire Harness, Spec. Monitor | EH50-00866-00

EH TOWER PLASTICS KIT EH TOWER GRAPHICS KIT

(TEMDESCRIPTIONPART NO.ITEMDESCRIPTIONPART NO.
1 __ | Tower Marquee Bezel£H90-00738-00 } | 1 | Tower, Right PanelEH40-00780-00
2__|Tower Acrylic Panel, Right£H90-00739-00 ] | 2 _| Tower, Left PanelEH40-00787-00
3 _| Tower Acrylic Panel, Left| £H90-00783-00 | | 3 _| Display Panel, 4P CenterEH40-00779-00

EH TOWER NANCO LTD. EXPORT KIT EH05-00885-00 | ITEM DESCRIPTION |_PART No. 1 Display LEDs [ EHO09-00882-00 2 | Tower PCB | EH03-00884-00

Page 43

10-5 Coin Assembly

Bi 91-1311-16

91-0604. 16 eI 91-1113-01 Ss 92-1002-021 i 1300-00 91-1121-00 90-1300- ° 91.1141.00 EY i Beppe 90-1000-00__po* is a \- . 90-1017-00 _—

L 91-0502.16 92-1002.01 ——_;

91-1117-00.

ee of L “& -®— 90-1003-00 “TT (91.0506-00 I 12-4150-011 12-4050-01

et 91-1120-00 90-1208-02 a

oot.€ =aS

92-1002-08 ~y ay 91-1408-01 Sa VY)

seroo2os”ffuswva
92100207Ss93-1107-00}

99-1007-00 os 91-1105-00 R ! 99-1110-00 91-1116-16 91-1125-00

92-1002-11

20-4177-00 —

90-1032-00

COIN CONTROLS COIN DOOR ASSEMBLY

Page 44

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 45

R Red = Gh

blue | BLWhite2h
Orange °Light Biuc+ LB
—- -—————=: - - .--—Yeliow ~- ¥Yellowish Green - GS
|Purple - Ppink= 31

Grey = cy

“ren Aieassy ianneTe

Ye rcoassr ae S| son ea) co reset SOP winstan Eoce| 1203

06NDcup fp}SRAK wout
Bee || eo] stieevee Ot? |
“ADGNO.ono? H——]A‘peeck (AMP car
MVecGND|attSw102
peperiar
nme | oa[ae(uanols D
TarePaern%

ANS Bae fr oe ts rz A nt my ry {as on Repent

=||:

Vee in [ar py} |) path see J

mupiotst| Me — 1§ 0 CTRDTeee
Seiwa) quoi tei] Hi—4 4wagerer]

Foam | }

b>RasuiH

SCOUT Greet 4 t

mivcsn_||— oLUEBe|!

ie | [SYNE

iG IK] | ~v-Gug fs 24 —~]I+sau!
AnouTwhtit|
co} Senviee [a~!
vee | | eer fa=|oti)

[conf

‘Sonecous? x~~}

rom sou —rP +

x~~serge;
jemaos ow ee|
my—P_22|9°P:
eeainSEALER SrnTesl S
a[>]46rae ZARFit eel cage ee
| yourrgn Sees4}aeBRReekese ermeagel

ASSY (2) “nefete) 6B 8 — LER. possessed |

(257)Lew=oBj
aie7LRLe eoatertt
feseaneee A?mriassErato
SaLA2Tea loemenererat | |
|°|
ONY2ree aaa yt
,rmcom sure |

Sie Be GR onrseuere a | ee cory CSAP = footer i Sas !

4W) 6ey ASSY[Goya seeecrre 2) j
4|cc com Zeusrer CD
  • ;
emmntes 3P-LLCON ASSY |

ce cous ceuzer (2)

Suzuka 8 hours™

  • Wiring Harness Diagram
Page 46

NOTES

Page 47

Nil <> b—— bs

fitness for a particular purpose, and of all other obligations or liabilities on the Seller's part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products by Seller.

Namco-America, Inc. distributors are independent, being privately owned and operated. In their judgement they may sell parts or accessories other than Namco-America, Inc. parts or accessories. Namco-America, Inc. cannot be responsible for the quality, suitability or safety of any non-Namco-America, Inc. part or any modification including labor which is periormed by such distributor. SOOO TO OU UU aa a"a eran a'a"n“e'a'n'sne'n0'e6'06'n'0'h'b'e6s 0'0'8's'6'0'0'8'0'0'0"s FO ee OOOO OU = a ¢) =e ee RO <4 =) _ k — = Warranty rs J) = > = <= =S> 4 — = bes a \ <_> = =

SS 4Seller warrants that its printed circuit boards and parts thereon are free from defects in>

S=4 = material and workmanship under normal use and service for a period of ninety (90) days K —

— 3from the date of shipment. Seller warrants that its video displays (in games supplied with—=—
C4_~__svideo displays) are free from defects in material and workmanship under normal use and———

SSA Cs senice for a period of thirty (30) days trom date of shipment. None of the Seller's other —s

=>producis or parts thereof are warranted.<=

4 <>

<—S4sit the products described in this manual fail to conform to this warranty, Seller's sole liabilityers
=4shall be, at its option, to repair, replace, or credit Buyer's account for such products which=
— 3are returned to Seller during said warranty period, provided:——

—>) —<—>

Ss(a)Seller is promptly notified in writing upon discovery by Buyer that said products areK =
=|defective;tS

Cn) p—_ >

  • S43) — Such products are returned prepaid to Seller's plant; and — = <sS
—S3(©) __ Seller's examination of said products discloses to Seller's satisfaction that such—=—
—4alleged defects existed and were not caused by accident, misuse, neglect, alteration,<>
—‘+:,.=

3 improper repair, installation, or improper testing. 6 =e, 6

<>}__sInno event shail Seller be liable for loss of profits, loss of use, incidental or consequentialx
SAdamages.6

<> 6

—S3Except for any express warranty set forth in a written contract between Seller and Buyerie
4)which contract supersedes the terms herein, this warranty is expressed in lieu of all other>
—'warranties expressed or implied, including the implied warranties of merchantability andif

Qa) cS 3 cS oS}

SS —o,

oO N NY TA

Page 48

namca

NAMCO-AMERICA, INC. 150 Charcot Avenue San Jose, CA 95131 U.S.A.

(408) 383-3900

FAX: (408) 383-0128

Reorder Number EH45-00832-00