CATHODE RAY TOMES

Sente SAC Field Conversion (M051-00C47-A019)

SAC 1, SAC 1A, SAC 1B, SAC-MAN & C.T. MAINFRAME (Bally Sente) · Field Conversion Kit · 17 pages · 15 sections · original scan

Page 1

==

FIELD CONVERSION KIT

SAC 1, SAC 1A, SAC 1B,

SAC-MAN & C.T. MAINFRAME

Phone (312) 451-9200 Cable Address Avenue

MIDCO~ Telex No. 72-1596

M05 1-00C47-A019

Page 2
WARNING

THIS GAME MUST BE GROUNDED. FAILURE TO DO SO MAY RESULT IN DESTRUCTION TO ELECTRONIC COMPONENTS.

WARNING: This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a CLASS A computing device pursuant to SUBPART J of PART 15 of FCC RULES, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures may be required to correct the interference.
iELECTRICALBULLETIN:FORALLAPPARATUSCOVEREDBYTHECANADIAN
|STANDARDSASSOCIATION(CSA) STANDARD C22.2 NO.1, WHICH EMPLOYS A

; SUPPLY CORD TERMINATED WITH A POLARIZED 2-PRONG ATTACHMENT PLUG.

CAUTION:TOPREVENT ELECTRIC SHOCKDONOT USE THIS (POLARIZED)

PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE ; EXPOSURE. :

ATTENTION:POUR PREVENIR CHOCSELECTRIQUESNE PASUTILISERCETTE
FICHEPOLARISEEAVECUNPROLONGATEUR.UNEPRISEDE
COURANTOUUNE AUTRESORTIEDECOURANT,SAUFSILES
ZLAMESPEUVENTETREINSEREESAFONDSANSENLAISSER

id AUCUNE PARTIE A DECOUVERT.

our TOLL FREE NUMBERS FOR SERVICE INFORMATION CONCERNING THIS GAME, OR ANY i OTHER BALLY/SENTE™ GAME YOU NOW HAVE ON LOCATION. La

CALL US FOR PROMPT, COURTEOUS ANSWERS TO YOUR PROBLEMS

ANSWERS TO YOUR PROBLEMS.

Video - Continental U.S. 800-323-7182 OW

. 10601 West Belmont Avenue Franklin Park, illinois, 60131 phone (312) 451-9200

©COPYRIGHT MCMLXXXVI BY BALLY SENTE INC. ALL RIGHTS RESERVED

NO PART OF THIS PUBLICATION MAY BE REPRODUCED BY ANY MECHANICAL, PHOTOGRAPHIC, OR ELECTRONIC PROCESS, ORIN THE FORM OF A PHONOGRAPHIC RECORDING, NOR MAY IT BE TRANSMITTED, OR OTHERWISE COPIED FOR PUBLIC OR PRIVATE USE, WITHOUT PERMISSION FROM THE PUBLISHER. THIS MANUAL IS FOR SERVICE USE ONLY, AND NOT FOR GENERAL DISTRIBUTION. FOR PERMISSION REQUESTS, WRITE BALLY/SENTE INC., 10601 W. BELMONT i AVE., FRANKLIN PARK, IL 60131

Printed in U.S.A.

Page 3
WARNING

The parts contained in this field conversion kit must be Installed without deviation from the instructions contained in this manual and kit. Failure to follow these instructions in every detail! may result in the creation of Illegal interference to radio and TV reception.

BALLY SENTE has verified that this field conversion kit, when installed in the game(s) specified in this manual, complies with the requirements in Part 15 of the FCC rules for a Class A computing device. Mperation of this equipment in a residential area may cause unacceptable interference to radio and TV reception, requiring the operator to take whatever steps are necessary to correct the interference.

BALLY SENTE will not be responsible for incomplete or improper conversions, or installation in a game for which this field conversion kit is not intended. If this field conversion kit is installed in a game that is not specified in this manual or in a previously converted game, the operator is required to take whatever steps are necessary to insure compliance with the requirements in Part 15, Subpart J, of the FCC Rules for a Class A computing device. °

SPECTAL NOTE:

DO NOT DISCARD ANY OF THE PARTS YOU REMOVE WHEN MAKING THE MODIFICATIONS EXPLAINED IN THIS MANUAL.

THEY WILL BE RE-USED IN FUTURE CONVERSION KIT!

Page 4

UPRIGHT KIT CONVERSION PROCEDURE FOR SAC 18, SAC 1A OR SAC 1 OR SAC-MAN*

To Change Attract (Header) Art

2. 3. 4a 5. 6. Remove bolts holding in Attract Retainer located at top front of cabinet. Remove Attract Retainer, Slide Attract Glass up and out of cabinet. Remove old Attract Art and replace with new Attract Art. Slide Attract Glass containing new are back into cabinet. Replace and secure Attract Retainer. Clean front of Attract Glass.

‘Yo Change Control! Panel !nsert Assembly (SAC 1B, SAC 1A or SAC 1)

1.

2.

3. 4.

5. Power off SAC 1R (SAC 1A or SAC 1) unit using switch on top of cabinet toward the back. Unlock Coin Mech door and reach through to unlatch large front door from inside cabinet. (One side jatch for SAC 1A or SAC 1. One top latch and one bottom latch for SAC 1B.) unlatch two (2) clamps !ocating Inside the cabinet at each end of Control! Panel, Disconnect the Control! Pane! Insert Assembiy harness from the main harness of SAC 1B (SAC 1A or SAC 1) unit. SAC 1R or SAC 1A Unit: Swing out Controf Panel on its hinge. SAC 1 Unit: Lift Control Pane! up, slide to right and pu!lt down to remove. Carefully pul! Control Panel harness wiring out of opening at rear of Control Panel tray. Remove bolts and nuts securing the old Control Panel Insert Assembiy to the Contro Panel. Remove old Insert Assembly. instal! new Controi Panel Insert Assembly by reversing this procedure, Power on SAC 1R (SAC 1A or SAC 1) unit using switch at rear of cabinet, Play game to check if all switches and controls are working properly.

To Change Game Cartridge

8. 9% 10. VW. 12.

BE SURE Power off SAC 1B (SAC IA or SAC 1) unit using switch on top of cabinet toward the back. Untock Coin Mech door and reach through to untatch large front door from inside cabinet. Find Game Cartridge On/Off Switch located at bottom front right of Electronic Chassis just inside Jarge front door (this switch may be used to power unit on and off in place of switch at rear of cabinet). Turn Game Cartridge On/Off Switch off to permit Game Cartridge to slide out of Electronic Chassis. Stide old Game Cartridge out of chassis. Slide new Game Cartridge between runners to plug Into the Main PC Roard. Be sure Game Cartridge Is securely plugged in. ROMs on the Game Cartridge should be facing to the left as you look Into the cabinet. Turn Game Cartridge On/Off Switch back on (this also locks cartridge into place). Check game option switch settings. Close and latch large front door. Close and lock Coin Mech door. Power on SAC 1R (SAC 1A or SAC 1) unit using switch at rear of cabinet. Play game to test if unit is working properly.

TO SAVE GAME CARTRIDGE, CONTROL PANEL INSERT, AND ATTRACT (HEADER FOR REUSE).

  • PLEASE REFER TO YOUR "SAC-MAN" FIELD CONVERSION KIT INSTRUCTION MANUAL FOR KIT CONVERSION PROCEDURE iNFORMATION,
Page 5

COCKTAIL TABLE KIT CONVERSION PROCEDURE

GENERAL :

The baslc purpose of this Instruction sheet is to give you some simple guide lines for instal{Ing your game kIt+ In the COCKTAIL TABLE MAINFRAME portion of your game cabinet. Guidelines, where applicable, are provided for removing all the parts of the old game. Turn your game off, unplug It from It's power source, and open it's Colin Door.

  • To convert the two Control Insert Assemblies:
NOTE: Each of the Control Insert Assembl!es Is held in place to the Control! Shelf

2.

3,

4. Sub-assembly by several screws, Two winghead screws (and washers) hold a-Light Shield and the Control (nsert Assembly against two Locating Brackets (with each bracket mounted to a Control Shelf Side plece and the inside of the Mainframe Cabinet). Three screws hold the bottom of the Control Insert Assembly to the hinge portion of a Bottom Plate and Hinge Assembly (which is also mounted to two Contro! Shelf Side pieces and the Inside of the Mainframe Cabinet).

A. Follow the "Cabinet Opening Instructions" In the following illustration to remove the

B.

C.

Dd. table top from the cabInet's pedestal.

Remove the Control! Insert Assembly by performing the following: . a

  • Disconnect the Control Insert Assembly's cabling trom the cabling of the Mainframe 5 cabinet.
  • Remove the winghead screws and washers holding the Control Insert Assembly to the Light Shield and the two Locating Brackets.
  • Remove the three screws holding the Control Insert Assembly to the Bottom Plate and Hinge Assembly.
  • Lift out the Assembly,
  • Remove the Light Shield and Lamp Assembly held by screws to the Control Insert Assembly.

To install the new game's two Control Insert Assemblies, reverse this procedure but leave the table top off of the cabinet's pedestal.

Player 1 contro! is always on the left side of game looking from the coin door.

Replace the old game's P.C. Cartridge with the P.C. Cartridge from your new game kit by referring to the following Illustration.

Secure the table top to the cabinet's pedestal.

To convert the Under lay:

A.

RB.

C. Remove the screws which secure the table top Main-Nisplay-Glass in place and then remove the table top Main-Display-Glass.

The old Underlay can be lifted off of the table top.

The new Underlay (as provided in the new game Field Conversion Kit) can be installed by reversing this procedure.

Close the Coin Door, reconnect the game's Power Plug to it's power source, turn it on arc run a Self-Test.

When through completing a positive Self-Test (everything checks good), your game is ready for use.

Page 6

=4-

CABINET OPENING INSTRUCTIONS

LATCHES

TO SERVICE MONITOR AND OTHER ELECTRONIC COMPONENTS OF GAME:

Is Il. Ill.

OPEN COIN BOX DOOR

WARNING: RIGHT HAND LATCH IS CLOSE TO HIGH VOLTAGE ON MONITOR

A. RELEASE THE TWO LATCHES INDICATED IN ABOVE SKETCH GRASP THE TABLE TOP AT "A", RAISE IT 90° AND LIFT IT STRAIGHT UP AND AWAY FROM THE GAME RELEASE THE TWO MONITOR RETAINING LATCHES INDICATED ABOVE AND TILT MONITOR TO THE SIDE

Page 7

C.P.U. BOARD REFERENCE DRAWING

oN

OPTION SWITCH

LOCATED AT "G=1™

LOCATED AT "H=I"

1234567 8 DOUUUUGH| 3

-5~

Page 8

Game Review

Self Test

Pressing the self-test switch on the chassis tray will cause the program to enter a sequenced self-test mode. First the screen RAM is tested by outputting a pattern to the monitor and checking it. This part of the test takes about 3 seconds and results in sta~ tus screen that indicates whether the screen RAM is good and also indicates the status of the ROM checksums. Pressing start 1 will then go to the. switch Input test where the state of all the controls and option switches is presented to the user. Pressing start 1 again will take the user to the game score statistics screen where a cumulative graph of scores and other Information is presented to the viewer. Next start 1 again will take the user to a similar game time statistics screen. On either this screen or the prior one, the user may choose to reset the cumulative statistics and high scores by pressing the start 2. Pressing start 1 yet again returns the user to the switch input screen. To exit self-test mode, the self-test switch must be returned to its original position on the game chassis.

. Attract Mode

  • When game is tirst powered on or when self-test mode is exited, a blank screen with the message loading appears for approximately 30 seconds. (This Is to allow the sound circuitry to be Inittalized).
  • Title screen will appear (approx. 8 seconds).
  • High score screen will appear (approx. 8 seconds). 4, Demonstation screen will appear (approx. 8 seconds).
  • Credits screen wil! appear (approx. 10 seconds).
  • Excetera.
  • Cycle repeats from Step 2.
Page 9
NOTE: FOR YOUR CONVENIENCE THESE ARE WICO PART NUMBERS.

15-172601

15-172800 15-173400

30-020500 15-174400

23-199100

15-172900

15-172207 30-131860 __+|

Track Ball Assembly (700-0162-01)

Page 10

15-9468 Ball Handle

15-9471 2” Washer

15-9473 Spring

30-0933 ve" E Ring

15-9478 Switch Actuator (.500" Dia. for 4-Way Joystick) \

15-9470 Switch Actuator (,600" Dia. for 2- & 8-Way Joystick)

Wico Joystick Assembly (700-0163-01)

Page 11

WICO JOYSTICK ASSEMBLY (700-0163-01) PARTS LIST PART NO. (WIC) DESCRIPTION QUANTITY

15.9468BALL HANDLE1
15-94712 WASHER1
18-9473,SPRING1
15-9470SWITCH ACTUATOR (.600" Di. FOR 2: & B:WAY JOYSTICK)1
15-9478SWITCH ACTUATOR (.500” DIA. FOR 4-WAY JOYSTICK)1
30-0933Yat E RING1
Page 12

SPEAKERS

ON/OFF 8H SAFETY SM SAFETY SH Top) <BOOR? WOLTAGE SELECTOR 6P0S A-N-L it 4, 348 vac SELECTION ‘CHELLOMD

be 4 4, 220 vac SELECTION ie a} cue

meer oF 29e1-10900-s008 aayoa nao wr aunae | Saas fre conrRoL Pawel fre comma. renee

Page 13

ONTROL. PANEL wore 3

Loose PINNED WIRES

BRLLY MIDUAY RFE. ce,

Page 14

amp f nor.27135 ava o20 fy TeN-W S049 ¥OL97135 3961704

(901) Ms 4123¥s mS 440/NO ira ea) syvoa uray 01 G4

aoa aNI7 {i} v bd 00s H109 01 Asst SfesuHa wrod

Page 15

2 n i flu ifastjarkaas eats aes Sef

NOTES: UNLESS OTHERWISE SPECIFIED === ee la

—— == TRACKBALL , CONN

Page 16

ALNAS

Ol-v008-900 wv AaY

Wi sey ies

q pURE

[S\=<z SRGANOD TWEYDVEL “MEWASSY S20 ly |vO-07-2008-900 e am ee] SevaTau Nowondons [ses] Vp

Page 17

PCB ASSEMBLY, TRACKBALL CONVERTER (006-8004-010A) (M051-00818-A007) PARTS LIST - SHEET 2 of 2

TTEMOly.PART NO.REFERENCEDESCRIPTION
11007-8004-0 1-0A0PCB,FAB,TRACKBALL CONVERTER
31210-0003-01u21C,DIG,CMOS,4013B,DUAL D F/F
41210-0009-01ulIC ,DIG,CMOS,4584B,HEX INV.
51260-0034-01U3IC,LIN,OP AMP ,TLO82,DUAL JFET
72330-0007-01C3, C5CAP, PES,RAD,0.O33UF , 100V, 10%
81310-0013-01c7CAP, TANT, AXL, 2. 2UF , 10V, 20%
9330-0009-01Cl, C2, C8CAP,CER,AXL,0. 1UF ,50V 20%
10233-0008-01C4, C6CAP ,RES,RAD ,0. 10UF , 100V, 10%

"1

12440-03301-01RI = R4RES,CF,1/4W,58,3.3K OHM
13240-01002-01R5, RBRES,CF,1/4W,5%,10K OHM
14240-0220-01R10, R7RES,CF, 1/4W,5%,220K OHM
15240-0390-01R6, RORES,CF,1/4W,5%,39K OHM
7210-0000-01CRI, CR2DIODE,S1, 10MA, 75P1V,1N914
19155-0006J9CONN, 8P ,MOLEX,09-74~1081
20655-00018-01J23CONN,PC,F,PINS,MLX 02-09-1134
21155-00061-01J23CONN, CBL,6P,RCP,MLX 03-09-1064