CATHODE RAY TOMES

Gain Ground

Gain Ground (World, 3 Players, Floppy Based, FD1094 317-0058-03d Rev A) (Sega, 1988) · Manual · 20 pages · 11 sections · original scan

Page 1

3 PLAYER TYPE

OWNER’S MANUAL

Page 2

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 3

TABLE OF CONTENTS

Introduction to the Owner’s Manual . Handling Precautions .........0. . Prevention of Counterfeiting and Conversion . Precautions Concerning the Place of Installation . . Opening the Front Door Name of Parts .........00+ . Removable Hinges and Control Panel ....... . Servicing the Power Supply Unit and Fuse . P.C. Board Assembly . Servicing the Floppy Disk

  • Monitor Adjustments and Game Board Servicing
  • P.C. Board Component Locations ..........sesee . 10
  • Service Switch Adjustment
  • Parts List
  • Adjustment Instruction Switch Setting Sheet
  • Disk Installation .
  • Schematic Diagram WaenNAWAWNE CANDADWNHRWHWNNEH

SPECIFICATIONS

INSTALLATION SPACE : 38 in. W x 42 in.D HEIGHT : 72 in. POWER : 201 W CR.T. : 26 MONITOR WEIGHT : 180 kg (394.5 Ibs.)

NOTE « Descriptions herein contained may be subject to improvement changes without notice.

INTRODUCTION TO THE OWNER’S MANUAL

SEGA ENTERPRISES, LTD., supported by its high electronic technology of LSIs, microprocessors, etc. and a wealth of experience, has for more than 30 years been supplying various innovative and popular game machines to the world market. This OWNER’S manual is intended to provide detailed comments together with all the necessary information covering the operation in general of electronic assemblies, electromechanicals, servicing control, spare parts, etc. as regards the GAIN GROUND 3 PLAYER TYPE, a new SEGA product. The manual is intended for those who have knowledge of electricity and technical expertise especially in ICs, CRTs, microprocessors, etc. Carefully read so as to acquire sufficient knowledge before working on the machine. Should there be a malfunction, non-technical personnel should under no circumstances touch the interior system.

Page 4

1, HANDLING PRECAUTIONS

When installing or inspecting, be very careful of the following points and pay attention to ensure that the player can enjoy the game safely.

  • Be sure to turn the power off before working on the machine.
  • To insert or pull out the plug quickly is dangerous.
  • It is necessary to make sure that the power cord or the grounding wire is not exposed on the road, etc. in a manner so as to be dangerous. Make sure that grounding connections are made safely at the position where so specified. ¢ Do not use any fuse that does not meet the specified rating. ¢ Make complete connections for the IC board and other connectors. Insufficient insertion is very dangerous. + For protection of the disk, please remove from machine prior to relocation.

Also, for the IC board circuit inspections, only the logic tone is allowed. The use of a tester is not permitted, so be careful in this regard. After confirming that there are no irregularities, turn the power ON.

  • PREVENTION OF COUNTERFEITING AND CONVERSION

LABELLING To prevent counterfeits and conversions, the following labels are put on all the SEGA products. When handling such goods, be sure to confirm the labels. They are used to prevent illegal acts such as the unauthorized copying of the products and the printed circuit boards thereof or carrying on business by manufacturing similar merchandise or by converting, selling or using such products or printed circuit boards.

ORIGINAL SEAL LICENSE SEAL The following seal is put on the The following seal is put on the machines manufactured by kits , such as the printed circuit boards, SEGA. of SEGA products.

COPYRIGHT NOTICE This SEGA product has the copyright notice as follows: © SEGA 1988 This signifies that this work was disclosed in 1988 and is the property of SEGA ENTERPRISES, LTD.

Page 5
  • PRECAUTIONS CONCERNING THE PLACE OF INSTALLATION

The GAIN GROUND 3 PLAYER is an indoor game machine. Absolutely do not install it outside. Even indoors, avoid installing in places mentioned below so as to ensure proper usage: Places subject to rain or water leakage, or condensation due to humidity. In the proximity of an indoor swimming pool and/or shower. Places subject to direct sunlight. Places subject to heat sources from heating units, etc., or hot air. Vicinity of highly inflammable/volatile chemicals or hazardous matter. Sloped surfaces. Vicinity of anti-disaster facilities such as fire exits and fire extinguishers. Places subject to any type of violent impact. Dusty places. er er er ey

  • OPENING THE FRONT DOOR OF THE GAIN GROUND 3 PLAYER To open the front door of the GAIN GROUND 3 PLAYER TYPE, follow the steps mentioned below:
  • Open the 3 slot Coin Door. + Locate 3 latches equally spaced on the right inside cabinet.
  • Carefully open the door to the left.
Page 6
  • NAME OF PARTS

MARQUEE

26” MID RES MONITOR

SIDE DECAL ___

3 POSITION COIN DOOR

FRONT DECAL

Page 7
  • REAR VIEW OF STEERING ASSEMBLY, FOOT PEDAL ASSEMBLY, REMOVABLE HINGES & CONTROL PANEL ASSEMBLY

Power Cord Box

Page 8
  • SERVICING THE POWER SUPPLY UNIT AND FUSE

Power Supply Assembly

OOOO®@

Page 9

834-6510

VO BD GAIN GROUND

837-6443

FDD BD SYSTEM 24

837-6571

MAIN BD SYSTEM 24

W/O SECURITY

FLOPPY DISK DRIVE UNIT

COVER

DS3-5000-01A is

GAME SOFT GAIN GROUND

Drawing of PC Assembly

Page 10
  • SERVICING THE FLOPPY DISK

Shield Case

REMOVE THE LID of the SHIELD CASE. Remove the sheet metal and pull out the game board unit in a manner so that both ends of it will meet the shield case. Open the FDD (loppy Disk Drive) LID by taking off the 2 (M3 x 8) SCREWS when replacing the FLOPPY DISK.

Page 11
  • MONITOR ADJUSTMENTS AND GAME BOARD SERVICING

Monitor Adjustment

bir SW #2

Page 12
  • PC BOARD COMPONENT LOCATIONS

SEGA® 837-6442 SYSTEM 24 © SEGA 1987 MADE IN JAPAN

sebll-udal

MAIN BD SY 24

IC1 EPR-12186 (IC MB27C1000-15) IC2 EPR-12187 (IC MB27C1000-15) IC3 IC 68000 IC4 ICSECURITY CPU 68000 OR IC 68000 FOR GAME PROGRAM

Swi SW2 CN2 CN 5 CN 3 DATA COMMUNICATION CONNECTOR CN 6 RESERVE POWER CONNECTOR CN7 INPUT (SOUND) CONNECTOR CN 8 HEADPHONE OUTPUT CONNECTOR RV 1 MAIN SOUND VOLUME RV2 HEADPHONE SOUND VOLUME FOR SYSTEM

DIP SW

Page 13

12, SERVICE SWITCH ADJUSTMENT

+ SERVICE SW (MAIN) Not used for the purpose of servicing (see below)

+ SERVICE SW 1, 2,3 Used for the purpose of servicing and increasing the credits without registering on the meter (this allows you to check the game).

+ TEST SW For operating this switch, see SELF-TEST.

  • VOLUME CONTROL Controls the speaker volume.

+ SERVICE SW (MAIN)

  • As regards the FLOPPY DISK BACKUP
  • The SYSTEM 24 BD used for the GAIN GROUND is provided with a game disk’s BACKUP mode. Use the supplied disk as a master disk and prepare the 3.5" 2HD TYPE for WRITE.

il

Page 14

Coin Door Assembly

¢ COIN MECH

¢ 3 COIN CHUTES

¢ SERVICE SWITCH BRACKET

Coin Door and Service Switch

Page 15
  • PARTS LIST

CABINET ASSEMBLY PARTS LIST

ITEMPARTS NUMBERDESCRIPTION
11050-0064MAIN SWITCH BRACKET
21170-5131ATERMINAL
31170-5131TERM BLK, 5P
41300-5018SPEAKER, 8-OHM 10W
52001-5125-24MONITOR 26
62200-0001COIN DOOR, 3 SLOT
72200-0101-ADECAL, 3 PLAYER COIN INPUT
82201-51305K OHM, LONG LIFE, LINEAR
92600-0011-1FAN, AXIAL
102600-0011-2FINGER GUARD
Ww2800-0418STRAIN RELIEF
123901-0002A40 WATT CLEAR LAMP
133901-0003DUAL LAMP FIXTURE
144001-5072PWR SUPPLY 5V-7A, 12V-2A
154201-5000-3DMANUAL GAIN GROUND
164211-6592STICKER ON/OFF
174211-6671STICKER, DANGER HIGH VOLTAGE
184211-6682STICKER, SERVICE INSTRUCTION
194211-7224STICKER, FUSE INST 5A, 5A
204211-7228STICKER, SWITCH UNIT
214231-0000-3DMARQUEE GAIN GROUND U/R
224750-0049RHEOSTAT, 100 OHM 10W
235090-0039SWITCH, ON/OFF
245090-5028SWITCH, PB MOM.
255140-0034FUSE, 5A
265140-0064FUSE HOLDER, 2P
275601-5126TRANSFORMER, 160P1
286000-0078POWER CORD 10 FT
296010-0001FUSE COVER
306010-0043KNOB, 1/8
316010-0420LINE FILTER, 5A
32HL1-4101SHIELD CASE
33HL1-4102SHIELD LID
34MO1-1215YPOWER CORD BOX
35UP1-0001MARQUEE BRACKET (TOP)
36UP1-0002SPEAKER BRACKET, MARQUEE (LOWER)
37UP1-0003CONTROL PANEL
38UP1-0103-ADECAL, P1 CONT. PNL.
39UP1-0103-BDECAL, P2 CONT. PNL.
40UP1-0103-CDECAL, P3 CONT. PNL.

Ai

42UP1-0005FRONT TRIM (VERTICAL)
Page 16

CABINET ASSEMBLY PARTS LIST

ITEMPARTS NUMBERDESCRIPTION
43UP1-0006CASH BOX LOCK BRACKET
44UP1-0007CASH BOX ASSY.
45UP1-0008SERVICE SWITCH BRACKET
46UP1-0009GLASS BRACKET (BOTTOM)
47UP1-0010HINGE, REMOVABLE TYPE
48UP1-0011LATCH BRACKET
49UP1-1102-ASIDE DECAL, LEFT (REAR)
50UP1-1102-BSIDE DECAL, RIGHT (REAR)
51UP1-1102-CSIDE DECAL, LEFT (FRONT)
52UP1-1102-DSIDE DECAL, RIGHT (FRONT)
53UP1-1102 EFRONT DECAL, LEFT (FLAGS)
54UP1-1102 FFRONT DECAL, RIGHT (FLAGS)
55UP1-1015-1GLASS, FRONT
57UP1-1115-3MONITOR BEZEL, WITH INST
59UP1-8888PACKAGING ASSY
60000-0308-FSM SCR PH WIFS M5 X8
61117-5123NAME PLATE ELEC SPEC
62421-5800-87ORIGINAL SEAL GAIN GROUND
63421-6119-91STICKER FCC
64421-6594STICKER SERIAL NO. INFO
65421-6709STICKER SERVICE INSTRUCTION
664201-0000-00ADJUST INST SH GAIN GROUND
67421-7209-01STICKER FDD COVER ENG
68600-5661CONN FEM 4P X 2
71600-5672ASSY FEM & FL CA 34P (L=250)
72601-6073RUBBER GROMMET
73610-0198ASSY FDD UNIT 3.5 TYPE
74835-6570-01GAME BD SYSTEM 24
75839-0141FILTER BD GAIN GROUND
76DS3-5000-3DGAME SOFT GAIN GROUND 3P
77HL-4202FDD BASE
78HL-4203FDD COVER
79HL-4205SASH RUBBER 110
80HL-4304FOD LID
Page 17
  • ADJUSTMENT INSTRUCTION SWITCH SETTING SHEET
COIN/CREDIT OPTION SWITCH SETTINGDIP SW #1PIN ASSIGNMENT
OPTION2727]*]s)]el[7]2COMPONENT SIDESOLDER SIDE
1 COIN+ CREDITOFF]OFF]OFFGNDaT AGND
1 COIN2 CREDITSOFF]OFF]OFFGND21BGND
1COIN3.CREDITSON | OFF]OFF31
+ COIN4.CREDITSon | oFF|OFFsv[ieav
1 COINSCREDITSOFF]ON | OFF+5V4[D+5V
1COIN6 CREDITSOFF]ON | OFFHavB/E+12V
seone: eeDeonajaCOINMETER1| 6[F |COINMETER2
4.COINS1 CREDITOFFOFF]ON(NoT USED) ~— | _7/H(NOT USED)
2. COINSSCREDITSOFF]OFF]ON(NOT USED)Bld(NOT USED)
1P WEAPON 19[K2P WEAPON 1

2 COINS 1 CREDIT

4 COINS2CREDITSon | off!on1P WEAPON 2s0[L2P WEAPON 2
5 COINS3 CREDITS1P SERVICEa3[M2P SERVICE
8 COINSSGREDITSNOT1PDOWN =[42[1N2P DOWN
2 COINS1 CREDIT4P UP13| P2PUP
IN |OFF]ONUSED
4 COINSS.CREDITS|e(ALL OFF)1P RIGHT14] R2P RIGHT
1 COIN4 CREDIT1P LEFTB/S2P LEFT
2 COINS2 CREDITS3P DOW
geomeScREone3p oe ta Uap uP "
4.COINS4 CREDITS| 17]
5 COINS6 CREDITSSPWEAPON2 = [78] V3P RIGHT
3P SERVICE19] W3P LEFT
1 COIN1 CREDITrol
2 COINS2 CREDITScon1[20[x(NOT USED)
3. COINS3CREDITScoIn2= [ail(NOT USED)
4 COINSS CREDITStest| 2alz(NOT USED)
1COIN1 CREDIT‘ON | ONALL SERVICE)| 23} a(NOT USED)
2 COINS3 CREDITS‘SPEAKER (+)24| b‘SPEAKER (-)
FREE PLAYon | oNONONRED[25/¢GREEN
COIN SW. #1COIN SW. #2BLUE — | 26] dCMP. SYNC
end[27/eGND
end[2a/fGND

GAME OPTION SWITCH SETTING DIP SW #2 56P P:3.96mm

OPTION 1 8

MONITOR NORMAL

FLOPTURNEDONBARE BD NO.

171-5553~ NOT USED

MODERATE LITTLE HARD HARD

GAME HARDEST

DIFFICULTY LITTLE EASY

EASY SYSTEM 24 EASIEST O0

EASIER

MODERATE 1 TIME LIMIT EASY PERSTAGE EASIEST

DIP SW2 DIP SW1 HARD

CLOCKOF 1 = 1.0S TIMELIMIT 1 =0.8S

vtytyvtyMONITOR
~O-0~O-90-0-0

x t wo won x t Swen won x 4 Ne WEAPON ict VERTICAL 2 1

4P SIDE2P SIDE9P SIDE421-7350-02

GAIN GROUND (834-6570-03~)

Page 18
  • DISK INSTALLATION
IMPORTANT

INSTALLATION INSTRUCTIONS

Gain Ground contains a revolutionary new memory system for video games. This memory system is a Floppy Disk System which is housed in the RF Cage. This system allows Sega to give you more memory at a Cost effective price.

To insure that no damage occurs to this delicate system during transit, we have packaged the Floppy Disk separately which must be installed upon receipt of the game. Please follow the listed instruction for the installation of the disk.

DISK INSTALLATION

  • Open Coin Door and remove Cash Box.
  • Open Cash Box and remove Floppy Disk. (NOTE: It is housed in a plastic protection cover.)
  • Reach thru the Coin Door opening and unlatch the three spring latches which hold the front assembly securely to the rear assembly of the game. These latches are located on the right, inside of the front assembly.
  • Once the three latches are unlocked, pull on the far right steering wheel and the fron assembly will swing oper to the left. This allows front access to the three player controls, PCB Assembly and Power Supply Assembly.
  • Remove the cover of the PCB RF Cage by removing the four sheet metal screws.
  • Remove the two screws located on the left side of the wooden base of the PCB Assembly.
  • Lift the left side of the PCB Assembly. This will allow access to the disk drive, which is located underneath the PCB.
  • Remove the disk from the plastic protection case and install it into the disk drive label side up with the metal cover protection slide installed first. The disk should slide in and snap down to indicate that it is securely inserted.
  • Replace the two screws that you removed in Step #7 to secure the Wooden PCB base to the RF Cage.
  • Replace the lid of the RF Cage using the four sheet metal screws that were removed from the assembly in Step #6.
  • Close the front assembly and latch.
  • Apply power to the game and verify proper operation. This completes the Drive Assembly.
  • For protection of the disk, please remove it from the machine prior to relocation.
Page 19

ort003} \1d0d xa Z-hL6 (Re ee ‘Ud | (aaa. WAAVTd © GNNOWD NIVO VOSS

  • SCHEMATIC DIAGRAM

OvLEONHO UND aT DEY CaND) al Heyes —>

, ‘Roowh) show HeAvel —Le €

z DVLGRUMOTIN NAO OAV

a Peoty

hi a a i Deraseee agave ce-smmetys E247 a et SE=809R 808. J rowvne 3339 @ RSET (A148 HAE ASEV 0000-18) cavern we-tosectve WOS-TH Cteee-428 7]

Page 20

SEGA ENTERPRISES, INC. (USA) 2149 Paragon Drive San Jose, CA 95131 Tel. (408) 435-0201 ©SEGA 1988