CATHODE RAY TOMES

Food Fight TM-229 1st Printing

Food Fight (rev 3) (General Computer Corporation (Atari license), 1982) · Technical Manual · 72 pages · 55 sections · original scan

Page 1

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 2

If reading through this manual does not lead to solving a certain maintenance problem, call TELEHELP® at the Atari Customer Service office in your geographical area, as shown below.

WEST and CENTRAL U.S.A. Parts and Service

Atari, Inc. California Customer Service Office 1105 N. Fair Oaks Avenue P. O. Box 427, Sunnyvale, CA 94086 Telex 17-1103 (Monday-Friday, 7:30-4:00 pm Pacific Time) From California, Alaska, or Hawaii @ (408) 745-2900 ee Service from anywhere in the area shown in white toll-free (800) 538-1611

EAST U.S.A. Service only

Atari, Inc. New Jersey Customer Service Office 12A World’s Fair Drive, Somerset, NJ 08873 Telex 37-9347 (Monday-Friday, 7:30-4:00 pm Eastern time) exe From New Jersey (201) 469-5993 exe From anywhere else in this area toll-free (800) 526-3849

EUROPE Parts and Service

Atari Ireland Limited European Customer Service Office Tipperary Town, Ireland Telex 28-165 TIPPERARY TOWN, (Monday-Friday, 9:00-6:00 pm GMT) IRELAND

BS 062-52155

Page 3

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 4

Food Fight

ii © 1983 by Atari, Inc. All rights reserved. No part Of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher. The game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the U.S. Copyright Act of 1976. This Act provides for increased penalties for violating federal copyright laws, Courts can impound infringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles. In addition, the Act provides for payment of statutory damages of up to $50,000 in certain cases. Infringers may also have to pay costs and attorneys’ fees, fines up to $25,000, and face an imprisonment of up to one year. Atari will aggressively enforce its copyrights against any infringers. We will use all legal means to immediately halt any manufacture, distribution, or operation of a copy of video games made by us. Anyone who purchases such copies risks forfeiting such a game.

Published by: ATARI, INC. 790 Sycamore Drive P.O. Box 906 Milpitas, California 95035

Printed in the U.S.A. 3M nde

Page 5

Notice Regarding Non-ATARI Parts

WARNING Use of non-ATARI parts or modifications of your ATARI game circuitry may adversely affect the safety of your game, and injure you or your players.

You may void the game warranty (printed on the inside back cover of this manual) if you do any of the following: © substitute non-ATARI parts in the game © modify or alter any circuits in the game by using kits or parts wot supplied by Atari.

Note

This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart) of Part 15 of Federal Communications Commission (FCC) Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area or modification to this equipment is likely to cause interference in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference. If you suspect interference from an ATARI® game at your location, check the following:

  • All green ground wires in the game are properly connected as shown in the game wiring diagram. © The power cord is properly plugged into a grounded three-wire outlet. © The game printed-circuit board(s) (PCB) is properly installed within the Electromagnetic Interference (EM1) cage.
  • The EMI Shield PCB is properly installed and connected in series with the game PCB harness. © All filter capacitors required on the EMI Shield PCB are properly soldered in place. If you are still unable to solve the interference problem, please contact ATARI Customer Service. See the inside front cover of this manual for service in your area. Food Fight

ii

Page 6

Food Fight

Table of Contents

1 Set-Up Procedures Howto Use This Manual. . . . Game Overview. Installation Specifications . Inspectingthe Game ...... Voltage-Plug Selection and Fuses. Switch Locations .... 1, Power On/Off Switch .

  • Utility Panel Switches .
  • Option Switches G. Selecting the Coin and Credit Options ..... 0.6.0.2... eee eee HOOD

2 Self-Test Procedure A. Self-Test Display. . B. Self-TestMenu ... C. Selecting the Options .. . 3 Illustrated Parts Lists Parts listsbeginon page ..... 66... eee eee eee

Appendix A Gimbal Joystick Maintenance ... 2... 0... ee eee es

Page 7

ons we Figure 1-1 Figure 1-2 Figure 1-3 Figure 1-4 Figure 2-1 Figure 2-2 Figure 2-3 Figure 2-4 Figure 2-5 Figure 2-6 Figure 2-7 Figure 3-1 Figure 3-2 Figure 3-3 Figure 3-4 Figure 3-5 Figure 3-6 Figure 3-7 Figure 3-8 Figure 3-9 Figure 3-10 Figure 3-11 Figure 3-12

Figure 3-13 Figure 3-14 Figure 3-15 Figure 3-16

Table 1-1 Table 1-2 Table 2-1 Table 2-2 Table 2-3 Table 2-4 Table 2-5 List of Illustrations

Game Overview, US-BuiitGame ........... 1-2 Game Over view, Ireland-Built Game 13 Voltage-Selection Plug and Fuse Locations , 15 Option Switch Locations .... 1-6 Main Self-TestMenu ... 23 Hardware Tests Menu 23 Switch Test Display... . . 2-4 Color Pattern 2-4 Rie enianaial : 2-4 Statistics Display. . 25 Options Display. . 26 Cabinet-Mounted Assemblies, US-Built Game . 3-2 Cabinet-Mounted Assemblies, Ireland-Built Game 3-4 Control Panel Assembly. 3-6 Gimbal Joystick Assembly. . . . . 3-8 Fluorescent Tube and Speaker, us- BuiltGame . 3-10 Fluorescent Tube and Attraction Panel, Ireland-Built Game . 3-12 Video Display, US-BuiltGame .... 3-13 Video Display, Ireland-Built Game . . 3-14 Utility Panel Assembly... . 3-15 Vertically Mounted Coin Door. » 3-16 American-Made Coin Door. ..... - . 3-19 Electromagnetic Interference (EMI) Cage Assembly and PCB Mounting Hardware EMI Shield PCB Assembly. Food Fight Game PCB . Regulator/Audio II PCB Assembly. . i Color Raster-Scan Power Supply Assembly. bead

List of Tables

Installation Specifications 1-4 Switch Settings for Price and Bonus Options . 1-7 Playfield RAM Locations . . 2-2 Program RAM Locations 2-2 Program ROM Locations 2-2 Sound Chip Locations . 2-4 Option Settings 2-6 Food Fight

Page 8

Food Fight

vi

Safety Summary

The following safety precautions apply to all game operators and service personnel. Specific warnings and cautions will be found throughout this manual where they apply.

WARNINGS

Properly Ground the Game. Players may receive an electrical shock if this game is not properly grounded! To avoid electrical shock, do not plug in the game until it has been inspected and properly grounded. This game should only be plugged into a grounded 3-wire outlet. If you have only a 2-wire outlet, we recommend you hire a licensed electrician to install a grounded outlet. Players may receive an electrical shock if the control panel, video display, EMI cage, fluorescent light assembly, and utility panel are not properly grounded! After servicing, check that the green ground wire or grounding clip for each assembly is firmly attached. Only then should you lock up the game. AC Power Connection. Before connecting the game to the AC power source, verify that the proper voltage-selection plug is installed on the game’s power supply. Disconnect Power During Repairs. To avoid electrical shock, disconnect the game from the AC power source before removing or repairing any part of the game. Discharge High Voltage from the Video Display. When removing or repairing the video display, extra precautions must be taken to avoid electical shock. High voltages may exist within the display circuitry and cathode-ray tube (CRT) even after power has been disconnected. Do not touch internal parts of the display with your hands or with metal objects held in your hands! Always discharge the high voltage from the CRT before servicing this area of the game. To discharge the CRT: Attach one end of a large, well-insulated, 18-gauge jumper wire to ground. Momentarily touch the free end of the grounded jumper to the anode by sliding it under the anode cap. Wait two minutes and discharge the anode again. Use Only ATARI Parts. Jo maintain the safety integrity of your ATARI game, use only ATARI authorized parts when repairing the game. Use of non-ATARI parts or modifications of the game circuitry may adversely affect the safety of your game, void the warranty, and injure you or your players. Handle Fluorescent Tube and CRT With Care. If you drop a fluorescent tube or CRT and it breaks, it will implode! Shattered glass can fly six feet or more from the implosion. Use the Proper Fuses. To avoid electrical shock, only use replacement fuses that are specified in the parts list for this game. Replacement fuses must match those replaced in fuse type. voltage rating, and current rating. In addition, the fuse cover must be in place during game operation.

CAUTION

Properly Attach All Connectors. Before turning on the game for the first time, make sure that all connectors are properly attached. Make sure that the connectors on each PCB are properly plugged in. Note that they are keyed to fit only one way. If they do not slip on easily, do not force them. A reversed connector may damage your game and void the warranty.

Page 9

Set-Up Procedures

A. How to Use This Manual

This manual, written for game operators and service technicians, describes the Food Fight™ game. The manual contains information about both the Ireland- and US-built games. Whenever information is unique to the Ireland-

built game, this symbol appears: *®

‘Whenever information is unique to the US-built game, this symbol appears:

Chapter 1 contains game specifications, inspection procedures, voltage plug and fuse information, switch locations, and option information. Chapter 2 contains self-test procedures. Chapter 3 contains illustrated parts lists. Figures 3-1 and 3-2 illustrate the US-built and the Ireland-built game cabinet. Italicized type on these figures refer you to other places in the manual for information about specific cabinet parts, Schematic diagrams of the game circuitry are included asa supplement to this manual.

Chapter 1

Page 10

Set-Up Procedures

Fluorescent Tube & Speaker See Figure 3-5

Video Display * Ee See Figure 3-7 oe

Control Panel See Figure 3-3 Gimbal Joystick See Figure 3-4

Utility Panel See Figure 3-9 I

Coin Door Assy.: | See Figures 3-10 & 3-11

WARNING Shock Hazard Do not plug in the game until it has been inspected. This game should only be connected to a grounded 3-wire outlet. If you have only a 2-wire outlel, we recommend you hire a licensed electrician to install a grounded outlet. Players may receive an electrical shock if this game is not properly grounded! Self-Test Switch

Power Supply See Figure 3-16

Power On/Off Switch

Figure 1-1 Game Overview—US-Built Game Food Fight

ame Identification Label x

‘Access Panet

EMI Cage See Figure 3-12 Game PCB * See Figure 3-14

EMI Shield PCB See Figure 3-13

Regulator! ‘Audio 1! PCB x See Figure 3-15

,CO

‘x Item with a Serial number label

Page 11

Food Fight

Fluorescent Tube & Attraction Panel See Figure 3-6

Video Display See Figure 3.8

Control Pane! See Figure 33 Gimbal Joystick ‘See Figure 3-4

Coin Door See Figures 3-10 & 3-11 |

Utility Panel See Figure 3-9

WARNING Shock Hazard Do not plug in the game until it has been inspected. This game should only be connected to a grounded 3-wire outlet. If you have only a 2-wire outlet, we recommend you hire a licensed electrician to install a grounded outlet. Players may receive an electrical shock if this game is not properly grounded! Set-Up Procedures
  • Game Identification Label

Access Panel

Game PCB See Figure 3-14 Self-Test Switch

Regulator! Audio I! PCB See Figure 3-15

Power Supply See Figure 3-16

Power On/Off Switch

Figure 1-2. Game Overview—Ireland-Built Game

Page 12

Set-Up Procedures

B. Game Overview

Food Fight hero, Charley Chuck, gets points by eating his ice cream cone before it melts. To do this, he must fightoff Oscar, Angelo, Jacques, and Zorba, the four chefs who rise from holes and throw food at him. When Chuck eats the cone, the ice-cream flavor changes and the game difficulty increases. All major parts of the US-built Food Fight game are illustrated in Figure 1-1. All major parts of the Ireland-built game are illustrated in Figure 1-2.

C. Installation

Specifications

Table 1-1 describes the physical, electrical, and environmental specifications of the game.

Table 1-1 Installation Specifications

Power Consumption 200 W Temperature Oto +38° C(+32 to +100° F) Humidity Not to exceed 95% relative Line Voltage 100 to 240 VAC US-Built Cabinet Width 62.5 cm (25.5 in.) Depth 86 cm (34 in.) Height 181.5 cm (72 in.) Treland-Built Cabinet Width 60 cm (24 in.) Depth 68 cm (27 in.) Height 170 cm (67 in.)

1-4 Food Fight

D. Inspecting the Game

Please inspect your game carefully to ensure that it was delivered to you in good condition.

WARNING Shock Hazard To avoid electrical shock, do not plug in the game until the procedures in Sections D and E have been completed! Donot touch internal parts of the display with your hands or with metal objects held in your hands!

Examine the exterior of the game cabinet for dents, chips, or broken parts. Remove the screws from the rear access panel. Unlock and open this panel and the coin door; inspect the interior of the game as follows: a. Ensure that all plug-in connectors (on the game harnesses) are firmly plugged in. Replug any connectors found unplugged. Do not force connectors together. The connectors are keyed so they only fitin the proper orientation. A reversed edge connector may damage a PCB and will void your warranty. b. Ensure that all plug-in integrated circuits on the PCB are firmly plugged into their sockets. c. Remove the tie-wrap that secures the coiled power cord inside the cabinet. Inspect the power cord for any cuts or dents in the insulation. Repair or replace it as required. Place the square strainrelief plate in the wood slot at the bottom of the rear panel opening. d. Inspect major subassemblies, such as the power supply, control panel, video display, and EMI cage. Make sure they are mounted securely and that the green ground wires are connected.

Page 13

Food Fight

E. Voltage-Plug Selection and Fuses

The power supply in your game contains six fuses, When you replace a fuse, use the identical type fuse with the same electrical rating (see Figure 1-3). This power supply operates on the line voltage of many countries. The power supply comes with either one, two, or three voltage-selection plugs. Plug voltages and wire

Voltage-Selection Plug

FUSE F2 (4A, 250 V) FUSE F3 (20 A, 32 V) FUSES F4F6 (4 A, 250 V) Set-Up Procedures

colors are 100 VAC (violet wire color), 120 VAC (yellow wire color), 220 VAC (blue wire color), and 240 VAC (brown wire color). See Figure 1-3 for placementof the voltage-selection plug. Before plugging in your game, check your line voltage. Next, check the wire color on the voltage-selection plug. Make sure the voltage-selection plug is correct for the voltage of your location. Now plug the game into a grounded 3-wire outlet.

FUSE Fi (7A, 250 Vp FUSE Fi (4A, 250 V)

Figure 1-3 Voltage-Selection Plug and Fuses

Page 14

Set-Up Procedures

E. Switch Locations

Power On/Off Switch The power on/off switch is located on the back of the cabinet on the lower left side (see Figure 1-1 or 1-2).

Utility Panel Switches

The volume control, coin counter(s), self-test switch, and auxiliary coin switch are on the utility panel. The utility

panel is located inside the upper coin door (see Figure 1-1

or 1-2), The volume control adjusts the level of sound produced by the game. The coin counter(s) records the number of coins entered into the game. The self-test switch initiates the self-test operating mode. The auxiliary coin switch is used to credit the game without activating a coin counter.

Option Switches

Option switches for game price selection are on the game printed-circuit board (PCB) at location SW1 (see Figure 1-4).

G. Selecting the Coin and Credit Options

Settings of the game coin and credit option switches are explained in Table 1-2. Options preset at the factory are shown by the « symbols. However, you may change the settings according to your individual needs.

Game PCB Food Fight

To verify other option selections, check the self-test display that appears when you turn on the game. Then, verify the option switch settings on the self-test display as described in Chapter 2, Checking Option Settings. Table 1-2 describes the settings for the DIP switch at location SW 1. This switch selects the game coin and credit options available for the left and right coin mechanisms. The basic unit of measurement is a coin worth $.25 or 1 DM. Thus, if you have a2 DM/1 DM coin door with two coin counters, set switch 5 at location SW1 to on. Then, different denominations are counted on the two coin counters.

NOTE Coin Option Interconnect Assembly JS5A-P55A (A039655-01) permits a coin placed in either coin mechanism to register in the same coin counter. The cable connector is located between the coin door harness and the main harness (see the Coin Option Interconnect Wiring Diagram in SP-229). When it is used, left coin mechanism option switches at SW 1 apply to both coin mechanisms. If you want different options for the left and right coin mechanisms, remove Coin Option Interconnect Assembly J55A-P55A and connect J55 directly to P55,

OFF 1-8

Figure 1-4 Option Switch Location

1-6

Page 15

Food Fight Set-Up Procedures

Table 1-2 Switch Settings for Coin and Credit Options

4 5 Settings of 8-Toggle Switch on Game PCB (at SW) 2 3 4 6 Option

Off Off Off On

On On

On Off

On Off

On On

Off On off On ofr On Off On

Off On off Off On On Off Off

On On Off Off Off Off On On

On On Free Play I coin 2 credits 1 coin 1 credit <4 2 coins 1 credit

Right Coin Mechanism 1 coin 1 credit 1 coin 4 credits 1 coin 5 credits 1 coin 6 credits

Left Coin Mechanism 1 coin 1 credit <4 1 coin 2 credits No bonus coins <4 No bonus coins For every 4 coins, logic adds 1 more coin For every 4 coins, logic adds 2 more coins For every 5 coins, logic adds ? more coin For every 3 coins, logic adds 1 more coin

No bonus coins No bonus coins

<4 Manufacturer's recommended settings

Page 16

*

Page 17

ees

Self-Test Procedure

This game will test itself and provide data to show that the game circuitry and controls are operating properly. Selftest data is presented visually on the player LEDs and the video display, and audibly through the speakers. No additional equipment is required.

We suggest that you perform a self-test when you first set

up, each time you collect money, change the game options, or suspect game failure.

Chapter 2

Page 18

Self-Test Procedures

A. Self-Test Display

‘When the power switch is turned on, Food Fight enters the automatic selftest mode, which tests playfield RAM, program ROM, and non-volatile RAM (NVRAM). At the beginning of these tests, both the one-player and two-player LEDs are lit. (This is so that the success or failure of the tests can be indicated even if the messages cannot be displayed on the monitor.) If the playfield RAM and program RAMare working, then the one-piayer LED turns off and the message RAM OK is displayed on the screen. If the playfield RAM fails, the one-player LED flashes one through four times followed by a pause. The playfield RAM number displayed corresponds to the board location of the faulty chip as shown in Table 2-1.

Table 2-1 Playfield RAM Locations

Playfield RAM

Number Board Location

1 3K 2 3L 3 3M 4 3N

If the program RAM fails, the one-player LED remains on, and the number of the bad chipis displayed. The program RAM number corresponds to the board location of the faulty chip as shown in Table 2-2.

Table 2-2 Program RAM Locations

Program RAM

0 8B 1 8A 2 9B 3 9A

After the RAM is checked, the checksums for program ROM are verified. Ifall ROMs check out correctly, then the two-player LED is turned offand the message ROM OK is displayed. If there are faulty chips, then the ROM number Food Fight

of each faulty chip is displayed. The ROM number corresponds to the board location of the faulty chipas shown. in Table 2-3

Table 2-3. Program ROM Locations

ROM Number Board Location

9C 8C 9D 8D OR 8E oF SF MAU RWNEO

After the program ROM is checked, the checksums for the NVRAM are verified. If all sections of the NVRAM check, then the message NVRAM OK is displayed. If any section of NVRAM fails, then the name of the faulty section is displayed and factory values from program ROM are used. instead of the values from that section. if playfield RAM, program RAM, and NVRAM check out correctly, Food Fight goes into the attract mode after five seconds. If NVRAM fails, the game will go into the attract mode when the THROW button has been pushed. The five sections of NVRAM are as follows: STATISTICS holds the values for the statistics display (see the description under Self-Test Menu). These vaiues can be reset using the options menu. TIME AND CREDITS holds the total time the machine has been on, and the totai number of credits. These appear at the bottom Of the statistics display and cannot be reset. HIGH SCORES holds the piayer initiais, scores, and levels achieved for the top three high-scoring games. These values appear at the top of the high-score table during the attract mode and can be reset using the options menu. OPTIONS holds the current settings for the game options, which can be displayed and/or changed using the options menu. JOYSTICK VALUES holds the maximum and minimum values for the analog joystick. See the description of Joystick Calibration under the TESTS option of the selftest Menu.

Page 19

ee Food Fight

B. Self-Test Menu

Food Fight has a menu-driven self-test mode which is entered by turning the self-test switch on. Turning the selftest switch offat any time during self-test mode causes the game to return to the attract mode. Immediately after the self-test switch is turned on, the main self-test menu appears as shown in Figure 2-1. Three choices are available—TESTS, STATISTICS, and OP- TIONS. Move the joystick up or down to change the current selection, which is displayed in red. Push the THROW button to select.

SELF-TEST

MOVE JOYSTICK TO CHANGE Push THROW TO SELECT

TESTS STATISTICS OPTIONS

TURN SELF-TEST SWITCH OFF TO END

Figure 2-1 Main Self-Test Menu

NOTE The two-player start button can be used to cycle through the selections in any of the self-test menus so the game can be tested even if the joystick is faulty.

Hardware Tests

Selecting TESTS causes the hardware test menu to appear as shown in Figure 2-2. There are five choices available— JOYSTICK CALIBRATION, SWITCH TEST, COLOR PATTERN, CONVERGENCE PATTERN, and SOUND TEST. Use the joystick and THROW button to select any option. Push the one-player start button to return to the main self-test menu, Self-Test Procedures

TESTS PUSH START 1 TO ENO TESTS

JOYSTICK CALIBRATION SWITCH TEST COLOR PATTERN CONVERGENCE PATTERN SOUND TEST

Figure 2-2 Hardware Tests Menu

JOYSTICK CALIBRATION resets the joystick minimum and maximum values, and should be used whenever the NVRAM or joystick is replaced. Hold the joystick steady for a full five seconds in each direction (left, right, up, down) to store new values. Push the oneplayer start button to return to the TESTS menu.

NOTE Food Fight is equipped with a self-calibrating, joystick, which checks its maximum and minimum values while the game is being played. Initial values are set at the factory and stored in NVRAM. When Food Fight is turned off, the NVRAM values are updated. Each time Food Fight is turned on, the current values are read out of NVRAM. If NVRAM fails (see the description under Automatic Self-Test), then the joystick is recalibrated as the game is being played. In this case, the contro! will be sluggish for the first game or two after the game is turned on.

2-3

Page 20

Self-Test Procedures

SWITCH TEST displays the state of the control panel switches, the joystick values, the coin inputs, and the dual-inline-package (DIP) switches as shown in Figure 2-3 Aone (1) indicates that the switch is on, and a zero (0) indicates it is off, All eight bits are displayed for each direction of the joystick. Push both the one- and two-player start buttons to end this test. See Chapter 1, Selecting the Options, for information on the settings of the DIP switch located on the game PCB.

RISHT COIN Aux COIN

OP swiTcHEs

Figure 2-3 Switch Test Display

COLOR PATTERN displays all 256 Food Fight colors

ona 16-by-16 grid of blocks in the center of the screen as

shown in Figure 2-4. Use this display to check for color adjustment. Press the one-player start button to end this test. The colors are properly adjusted when the background is black and each colored block is distinguishable from those around it. Food Fight has four blue levels, eight green levels, and eight red levels. These are overlayed to display the color grid as follows:

  • Blue is displayed in four quadrants with level 0 (no blue) in the lower left quadrant, level 1 in the lower tight quadrant, level 2 in the upper left quadrant, and level 3 (intense blue) in the upper right quadrant.
  • — Greenis displayed in sixteen horizontal bars, two bars for each level, with level 0 (no green) bars at the center, level 7 (intense green) bars across the top and bottom, and intermediate leveis in between. ¢ — Red is displayed in sixteen vertical bars, with level 0 (no red) bars at the center, level 7 (intense red) bars at the right and left, and intermediate levels in between.

2-4 Food Fight

Figure 2-4 Color Pattern

CONVERGENCE PATTERN a white crosshatch pattern

appears on the screen as shown in Figure 2-5. Use this pattern for convergence (see the raster-scan video display manual for a detailed procedure). Push the one-player start button to end this test.

Figure 2-5 Convergence Pattern

SOUND TEST tests the twelve channels of the three Custom Audio sound chips. As the channel number is displayed, the test sound is played. The test continues to cycle through the channels until the one-player start button is pressed to end the test. The channels correspond to the three Custom Audio chips as shown in Table 2-4.

Page 21

Food Fight

Table 2-4 Sound Chip Locations

Chip No. Board Location Channels

1K/L5,6, 11, 12
211L/M1,2,7,8
311N2, 4,9, 10

Selecting the Statistics

This is the second selection on the main self-test menu. Selecting STATISTICS causes the game statistics display to appear as shown in Figure 2-6, Press the one-player start button to end this test.

STATISTICS PUSH START 1 TO END

NUMBER OF Games

'WO- PLAYER

camoor ®

T i ) rt rx

00:50:20 °

Figure 2-6 Statistics Display

The totals on the display are those accumulated since the statistics were last reset. All statistics (except the last two) can be reset using the CLEAR VALUES, and STATISTICS selections ofthe options menu. All times on the display are

shown as hours:minutes:seconds. The following statistics

are displayed: NUMBER OF GAMES reads the number of one-player games, the number of two-player games (increased by one for each two-player game), and the total number of games. COIN COUNT reads the number of coins inserted through each of the right and left coin mechanisms. CREDITS reads the number of paid credits, free credits (entered using the auxiliary coin button), and the total credits since the statistics were last reset.

BONUS MEN EARNED reads the number of bonus lives (extra Chucks) earned at the first stage at higher stages using level select, and the total. It also shows the percentage of games played in which at least one bonus life was earned, Self-Test Procedures

AVERAGE TIME reads the average times between credits and games.

LONG GAME reads the longest time a player was able to play on one credit. TOTAL TIME ON reads the total time the game has been turned on since the statistics were last reset.

IN PLAY MODE teads the percentage of time the game has been in play mode (as opposed to attract mode) since the statistics were last reset.

NOTE The last two statistics cannot be reset. They are accumulated from the date the game was manufactured, or since the NVRAM last failed or was replaced.

‘TOTAL TIME reads the totalamount of time the game has been turned on.

‘TOTAL CREDITS reads the total number of credits.

C. Selecting the Options

Selecting OPTIONS, the third selection on the main selftest menu, causes the options display shown in Figure 2-7 to appear. Use this display to view or change game option settings, or to clear the high scores or statistics. Push the THROW button to cycle through values on the current row (indicated in red), Change the current row using the joystick or the two-player start button, Push the one-player start button to end this display and make the displayed option settings the current settings.

OPTIONS MOVE YOYSTICK TO PUSH THROW TO CHANGE SETTINGS PUSH START 1 TO END CHANGE ROW

& m <z mio COD AMM Hm OBR -=O2-4C¢OD4. < OM ZROBANTON EDF OM

FJ n a rT

S F

ul ul a & ¢ fet T c € pco fs) r n wry lal a po

Page 22

Self-Test Procedures

To restore settings or to clear values, select the desired row and push the THROW button. RESTORED or CLEARED is then displayed. The options and settings available are listed in Table 2-5.

NOTE ‘Turning off the self-test switch during this display will cause the current option settings, the high scores, and statistics co be unaffected.

Description of Option Terms

LIVES PER GAME sets the initial number of lives (Chucks), not including bonus lives, given for each credit. DIFFICULTY sets the game difficulty at levels 4 and above. Level 1 is easy, level 5 is hard. BONUS STAGES. sets the scores at which the first or subsequent bonus lives are awarded. Additional bonus lives are awarded when the score reaches a multiple of the higher bonus stage. For example, when the factory settings of 25,000 and 100,000 are in effect, bonus lives are awarded at 25,000; 100,000; 200,000; 300,000; etc. The first bonus stage may not exceed the second bonus stage. If the two are equal, only one bonus life is awarded when the score reaches the first bonus stage. For example, if both stages are set to 25,000, then bonus lives are awarded at 25,000; 50,000; 75,000; etc. Either one or both bonus stages can be turned off. LEVEL SELECT BONUS if turned on, awards bonus lives when the player uses level select to start the game at or above level 10. An extra life is awarded for starting at levels at or above every multiple of 10, with one additional life at level 125. For example, ten bonus lives would be Food Fight

awarded for starting at level 103, These bonus lives are given at the start of the game in addition to the LIVES PER GAME. The level at which bonus lives are earned and the current number of lives awarded are displayed with Chuck heads during level select.

LEVEL SELECT MODE effects how the level select feature is handled, There are four possible settings: ¢ NORMAL allows the player to select a starting level if

the last game endediess than 15 seconds before, and if

the maximum level achieved in the last game was greater than level one. If both of these cases hold, the player is allowed to select a starting level up to the maximum level achieved in the last game. *@ CONSTANT always allows the player to select a starting level up to at least level 9. If the last game ended less than 15 seconds before, the player is allowed to select up to the maximum level achieved in the last game. This setting could be used in a location where the players are familiar enough with Food Fight that they would not be confused by the level select screen coming up at the beginning of the game. *° DEMO always allows the player to select up to the maximum Food Fight level, for example, level 125. This setting would probably not be used for a game out on location, but is useful to demonstrate the performance of the game at high levels.

  • OFF causes no level select display to occur.

ATTRACT SOUNDS disables the attract mode sounds if in the OFF setting. COIN COUNTERS causes both coin mechanisms to drive the same coin counter if in the ONE setting.

Table 2-5 Option Settings

Option Settings Available Factory Setting

Lives per game2-53
Difficulty1-52
First bonus stageOff, 5000-1,000,00025,000
Higher bonus stageOff, 5000-—-1,000,000100,000,
Level select bonusOff/On.On
Level select modeNormal, constant, demo, offConstant
Attract soundsOff/OnOn

Language English, German, Spanish, French English

Cocktail modeOff/OnOff
Coin countersOne/TwoOne
Page 23

aad Food Fight

RESTORE SETTINGS resets the displayed option settings to one of the following: ¢ CURRENT displays the option settings in effect before the option menu was entered. e FACTORY displays the option settings from the program ROM.

NOTE

The present self-test program causes an error in the option menu display when the factory settings are restored. The coin counter display should be set for TWO when any of the options are changed. Self-Test Procedures

NOTE

Remember that the high scores and statistics will NOT be affected if the options menu is ended by turning off the self-test switch.

CLEAR VALUES resets the high-score table to its factory setting and resets to zero all the items on the statistics display, except for the TOTAL TIME and TOTAL CRED- ITS. The clear takes effect when the options menu is ended using the one-player start button.

2-7

Page 24

BO a

Page 25

Illustrated Parts Lists

This chapter provides information you need to order parts for your game. Common hardware (screws, nuts, washers, etc.) has been deleted from most of the parts lists. However, there is a parts list for the hardware to mount the game PCB and Regulator/Audio I PCB to the cabinet. The PCB parts lists are arranged in alphabetical order by component. Each component subsection is arranged alphanumerically by reference designator. Other parts lists are arranged alphanumerically by Atari part number. In these parts lists, all A-prefix numbers come first. Following these are numbers in sequence evaluated up to the hyphen, namely 00- through 99-. then 000598- through approximately 201000-. When ordering parts, please give the part number, part name, number of this manual, and serial number of your game. This will aid in filling your order rapidly and correctly. We hope the results will be less downtime and more profit from your game. Atari Customer Service numbers are listed on the inside front cover of this manual.

Chapter 3

Page 26

Food Fight IMlusteated Parts Lists

Manuals, Schematics, & Self- Test Label— See parts list on following page

Fluorescent Tube & Speaker ‘See Figure 35 03733201 178034024 (Vert. grille) (T-Moiding)

A039735-01 (Cabinet assy)

Video Display 4 ~LEE Q, See Figure 3-7 03741201 —=— (Display shield) A038881-01 | qj (Lock) ——— 037419-02 178013-001. (Access panel) (Latch) r

Gimbal Joystick See Figure 3-4 EMI Cage ry See Figure 3-12 ° Contro} Pane! Game PCB See Faure 38 See Figure 3-14 4

Utility Panel Assy. EMI Shield PCB See Figure 3-9 See Figure 3-13

A039909-01 coin (Main harn. assy.)

See Figures 3-10 & 3-11 Regulator! Audio || PCB 038091-01 See Figure 3-15 (Coin box} A039910-01 038870-01 (Power harn. assy.) (Coin box enclosure) 178048-001 EN (Caster) SZ

A037470-01 Power Supp (Power on/ott A037453-03 . See Figure 3-16 Switch assy) (Power cord)

009992-01 78-3201 (On/off switch cover) + (Glide)

Figure 3-1 Cabinet-Mounted Assemblies US-Built Game A039734-01 A

3-2

Page 27

Illustrated Parts Lists Food Fight

Cabinet-Mounted Assemblies Parts List

Part No. Description

A037453-03 Strain-Relief Power Cord (U.S. and Canada) A03 7470-01 Power On/Off Switch and Mounting Plate Assembly A038881-01 Lock Assembly (for rear access panel) Acceptable substitute is part no. A038881-03 A039735-01 Cabinet Assembly (includes glides and PCB retainers, but not the rear access panel)

A039909-01 Main Harness Assembly A039910-01 Power Harness Assembly

The following four items are technical information supplements to this game: SP-229 Food Fight Schematic Package ST-229-01 Food Fight Label with Self-Test Procedure and Option Switch Settings TM-160. Service Manual for 19-Inch Electrohome Color Raster Display (use with part no. 92-049) Acceptable substitute is TM- 220, for use with part no. 139003-1004 TM-229 Food Fight Operators Manuai with Illustrated Parts List

78-3201 Adjustable Glide 009992-01 Power On/Off Switch Cover 036495-01 Speaker Grille (not shown) 037332-01 Yentilation Grille

037419-02 Reat Access Panel (does not include lock} 038091-01 Molded Coin Box 038870-01 Coin Box Enclosure 039752-01 Video Display Shield

178013-001 Spring Draw Latch 178034-024 44-inch Black Plastic T-Molding 178048-001 2-Inch Rigid Caster

Page 28

Ilustrated Parts Lists

Manuals, Schematics, & Self-Test Lal ‘See parts list on following page

Fluorescent Tube & Attraction Panel Food Fight

See Figure 36

038992-01 (Display shield) oaras2-01 (Vent. grille)

Video Display ; See Figure 3-8

(Latch) L | ‘A038881-01

03689101 ! je S| (Speaker grille) = ° oseo7ec2 Control Panel belt See Figure 3-3 (Access Panel) pe Gimbal Joystick See Figure 3-4 Game PCB Coin Door Assy. See Figure 3-14 -oin Door fe See Figures 3-10 & 3-11

A039999-01 038781-01 (Main harn. assy.) (Coin box ay Panel Assy enclosure) a Regulator! Audio 11 PCB See Figure 3-15

178034-024 (T-Molding) (Power harn. assy.) ° 037784-03 (Power cord) 038091-01 . (Coin Box) 4 J 78-3201 a (Glide)

Power Supply See Figure 3-16

‘A037470.01 (Power on/off & switch assy) 009992-01 (On/off switch cover)

Figure 3-2 Cabinet-Mounted Assemblies Ireland-Buiit Game A040005-02 A

3-4

Page 29

Food Fight ‘illustrated Parts Lists

Cabinet-Mounted Assemblies Parts List

Part No. Description

A037470-01 Power On/Off Switch & Mounting Plate Assembly A037784-03 Strain-Relief Power Cord (United Kingdom, Ireland, Lebanon, Saudi Arabia, India, Hong Kong, Singapore, Egypt, Nigeria, Republic of South African, Zimbabwe) A038881-01 Lock Assembly (for rear access panel) A039999-01 Main Harness Assembly

A040000-01 Power Harness Assembly A040006-01 Cabinet Assembly (includes glides and PCB retainers, but not the rear access panel) ‘The following five items are technical information supplements to this game: SP-229 Food Fight Schematic Package ST-229-01 Food Fight Label with Self-Test Procedure and Option Switch Settings TM-160 Service Manval for 19-Inch Electrohome Color Raster Display (use with part no. 92-049) or TM-201 Service Manual for 19-Inch Wells Gardner Color Raster Display (use with part no. 92-055) T™ 229 Food Fight Operators Manual with Lllustrated Parts List

72-6810S #8 x ¥,-Inch Cross-Recessed, Pan-Head Screw 78-3201 Adjustable Glide 009992-01 Power On/Off Switch Cover 034536-02 Foam Pad (not shown)

036891-01 Speaker Grille 037332-01 Ventilation Grille 038976-02 Rear Access Panel (does not include lock) 038091-01 Molded Coin Box

038781-01 Coin Box Enciosure 038992-01 Video Display Shield 148001-013, Speaker 175004-708 #8 Flat Fiber Washer

78013-001 Spring Draw Latch 178034-024 ¥4-Inch Black Plastic T-Molding.

3:5:

Page 30

Illustrated Parts Lists Food Fight

Players may receive an electrical shock if this control panel is not HORIZONTAL POTENTIOMETER properly grounded! After servicing any parts on the panel, make RED sure that the ground wire is firm: ly attached to the metal tab on VIOLET the inside of the control panel. VERTICAL POTENTIOMETER asad 75-9910NO 75-5516B BLACK (Nut) (Bolt)

160013-001 (Leaf switch & button holder)

178030-007 (Yellow pushbutton)

177010-244 (Locknut) 62-039 {LED switch) 75-015S S )— (Washer)

036895-01 (Switch bezel)

A039911-01 (Harness)

A039745-01 Ea A040012-01 * (Control panel (Control panel with decal) with decal) 039749-04 039749-04 {Decal—not shown} (Decal-not shown) 039744-01 040013-01 (Control! pane!) (Control panel)

Figure 3-3 Control Panel Assembly US-Built Game A039746-01 A Ireland-Built Game A040011-01 A

3-6

Page 31

ak Food Fight Illustrated Parts Lists

Control Panel Assembly Parts List

Part No. Description

US-Built

A039745-01 Control Panel with Decal 78-6900402 Vinyl Foam Single-Coated Adhesive Tape, %4-Inch Wide x ¥%Inch Thick (24 inches required) 039744-01 Control Panel 039749-04 Control Panel Decal (not shown)

A040012-01 039749-04 040013-01 179125-001

A038838-02 A039911-01 62-039 75-0158,

75-5516B 75-99 10NO 036895-01 160013-001

177010-244 178030-007 Treland-Built

Control Panel with Decal Control Panel Decal (not shown) Control Panel Grounding Terminal (not shown)

US- and Ireland-Built

Gimbal Joystick Assembly Control Panel Harness Assembly SPDT Momentary Pushbutton Start Switch with Red Light-Emitting Diode #¥%4 Flat Washer

#¥%-20 x L-lnch Black Carriage Bolt #4 x 11 Stamped Nut Black Molded Switch Bezel Leaf Switch and Button Holder (leaf switch only is part no. 160012-001)

#%4-20 Hex Locknut Yellow Pushbutton Assembly

Page 32

Illustrated Parts Lists Food Fight

036953-01 2 SK

(Square control:—

plate) IS a ~ < 03994001 . | (Knob) =) (Knob) 03695201 | . A038839-01 : 2

(Pivot shaft assy);A(Housing)

0388.42.01 : Gren) Zhe: 72-5240

BENSthEgy|(Screw)

; e \ (Slide plate) (Pivot ball) >

036954-01 (Mounting plate)

A037853-01 (Bellows)

036955-01 (Bellows cap)

75-940S (Hex nut)

036957-01 ( (Linkage)

03695601 (inner gimbal) 49.0026 (Resistor) *

: See Appendix A for lubrication (Cuter gimbal) information,

Figure 3-4 Gimbal Joystick Assembly A038838-02 A

3-8

Page 33

th

on

al. Food Fight Illustrated Parts Lists

Gimbal Joystick Assembly Parts List

Part No. Description

A037853-01 Bellows Assembly A038839-01 Pivot Shaft Assembly (includes pivot ball, pivot shaft and slotted pin)

  • 19-9026 5kQ, +20%, 2% W Variable Resistor (acceptable substitute is part no. 119000-502) 72-5240 #10-32 x 2%-Inch, Zinc-Plated Steel Machine Screw

72-8406 #4-40 x ginch Socket-Head Steel Machine Screw 73-21224 ¥e-Anch Diameter x 1 ¥-Inch Long Slotted Pin 75-0108 #10 Flat Zinc-Plated Steel Washer 75-07020 YeInch Interior Diameter Special Flat Washer

75-9408 #10-32 Self-Locking Hex Nut 0362.79-03 Pivot Ball 036952-01 Pivot Ball Housing (two required per handle) 036953-01 Square Control Plate

036954-01 Mounting Plate 036955-01 Bellows Cap 036956-01 Inner Gimbal 036956-02 Outer Gimbal

036957-01 Gimbal Linkage 036963-01 Slide Plate 03884201 Pivot Shaft 039940-01 Pivot Ball Knob 178027-001 Nyogel 779 Lubricant

Page 34

Illustrated Parts Lists Food Fight

148001013 (Speaker) 70-304 99-11006 x (Tab) o

179035-001 79-561816P (Tube holder) (Wire nut) A037457-01 (Harness)

142028-001 (Transformer)

037489-01 (Bracket)

99-11003 (Starter)

99-11009 (Socket) 'A037540-01 (Ground wire)

636498-01 (Upper retainer)

~ oaa76101

(Attraction panel w graphics) 78-6900404 (Tape)

003053-01 (Lower retainer)

NOTE

To ensure that the fluorescent tube starts, make sure the ground wire is firmly attached to both the ballast transformer and the steel tube bracket.

Figure 3-5 Fluorescent Tube and Speaker Assembly A039737-01 A US-Built Game

3-10 awe

eae

ay

es

Page 35

care, i Food Fight Ilustrated Parts Lists

Fluorescent Tube and Speaker Assembly Parts List

Part No. Description

A037457-01 Tube and Speaker Harness Assembly A037540-01 Ground Wire with Ring Lug 70-304 18-Inch, 15-Watt, Cool White Fluorescent Tube 78-6900404 Viny! Foam Single-Coated Adhesive Tape, 44-Inch Wide x %-Inch Thick (48 inches required)

79-561816P spring-Connector Wire Nut for 16- to 18-Gauge Wires 99-11003 Fluorescent Tube Starter 99-11006 Fluorescent Tube Locking Tab (consists of two pieces) 99-11009 Starter Socket

003053-01 Lower Attraction Panel Retainer 036498-01 Upper Attraction Panel Retainer 037469-01 Steel Tube Bracket 038151-01 15-Inch Jumper Wire

039751-01 Attraction Panel with Graphics 142028-001 60 Hz, 118-Volt, Ballast Transformer (used on AQ38161-01 assembly) 148001-013 6x 9-Inch Oval, 4 2, 6-Ounce, Shielded High-Fidelity Speaker 179035-001 2-Pin Fluorescent Tube holder

Page 36

Illustrated Parts Lists Food Fight

040020-01 (Upper retainer) 99-1109 (Socket) 142028-002 se-tions (ianstormer} (Starter) A005493-01 (Harness}

(Y4ead connector)

A040008-01 Attraction panel wi graphics)

70-303 (Tube)

99-11012 (Clamp)

NOTE To ensure that the fluorescent 038986-01 tube starts, make sure the (Lower retainer) ground wire is firmly attached to the ballast transformer.

Figure 3-6 Fluorescent Tube and Attraction Panel Ireland-Built Game

Parts List

Part No. Description

A005493-01 Fluorescent Tube Harness Assembly 404000801 Attraction Panel with Graphics 70-303 184nch, 15-Watt, Cool White Fluorescent Tube 78-6900402 Vinyl Foam Single-Coated Adhesive Tape, “Inch Wide x ¥%Inch Thick (not shown—48 inches required)

99-11003 Fluorescent Tube Starter 99-11009 Starter Socket 99-11012 1 %-Inch Fluorescent Tube Clamp 035835-O1 12-Inch Y-Lead Connector 038986-01 Lower Attraction Panel Retainer 640020-01 Upper Attraction Panel Retainer 142028-001 50 Hz, 118 V, Ballast Transformer ad say

Page 37

ne ay

he: Food Fight

amon ce | ae

039752-01 (Shield)

Shock Hazard The following procedure should only be performed by a qualified service technician. Before removing or repairing the video display, unplug the game.

High voltages may exist in any video display, even with power disconnected. Use extreme caution and do not touch electrical (Electrohome dispiay)

WARNING

Parts of the display yoke area with your hands or with metal ‘objects in your hands!

Discharge the high-voltage from the cathode ray tube as follows: Attach one end of a large, wellinsulated, 20-kV jumper to ground. Momentarily touch the free end of the grounded jumper to the anode by sliding it under Illustrated Parts Lists

the anode cap. Wait two minutes and discharge the anode again.

Implosion Hazard If you drop the display and the picture tube breaks, it will implode! Shattered glass and the yoke can fly six feet or more from the implosion. Use care when replacing any display.

Figure 3-7 Video Display US-Built Game

Parts List

Part No. Description

78-6900402 Vinyl Foam Single-Coated Adhesive Tape, Y4-Inch Wide x Inch Thick (24 inches required) 039750-01 Display Bezel 039752-01 Display Shield with Graphics 92-049 19-Inch Electrohome Color Raster-Scan Display (Acceptable substitute is part no. 139003-1004—19-Inch Matsushita Color Raster-Scan Dispiay)

Page 38

Illustrated Parts Lists Food Fight

038992-01 038808-01 (Shield) (Bezel)

002728-01 (Bracket)

038805-01 92-049 (Retainer) (Electrohome display) or 92-055 (Wells Gardner display) he

Figure 3-8 Video Display Ireland-Built Game Parts List

Part No. Description ‘ ° 78-6900402 Vinyl Foam Single-Coated Adhesive Tape, %-Inch Wide x }j-Inch Thick (48 inches required—not shown) Ss 92-049 19-Inch Electrohome Color Raster-Scan Display or 92-055 19-Inch Wells Gardner Color Raster-Scan Display 002728-01 Metal Support Bracket

038804-02 Display Shelf 038805-01 Display Shield Retainer 038808-01 Display Bezel 03899201 Display Shield

Page 39

we

sae

ay

ala Food Fight Illustrated Parts Lists

A002465-01 ‘A038004-01 WA (Harness) (Coin counter)

038003-01 (Bracket)

62.041 (Auxiliary coin switch)

19-9032 mS) ~ 7 >» (Volume control) eae) (ez 178018-002 Ae SAQQ (Screw) 69-001 (Self-test switch) 178070-001 (Volume contro! knob)

WARNING Before removing or repairing the utility panel, turn the game off. Players may receive an electrical shock if the utility panel is not properly grounded! After servic- NOTE ing any parts on the panel, make i |-Built cabinet ‘sure that the ground wire is firm- a Aled on pense 7 ly attached to the metal screw on the back of the coin counter.

Figure 3-9 Utility Panel Assembly A038002-01 &-02 G Parts List

Part No, Description

A002465-01 6 V Coin Counter A038004-01 Utility Panel Harness 19-9032 Volume Control 62-041 SPDT Momentary-Contact Pushbutton Auxiliary Coin Switch with Black Cap

69-091 DPDT Self-Test Switch 75-9168 #6-32 Standard Machine Nut 038003-01 Utility Panel 75-9910WO 'y,,-32 Stamped Nut

176018-002 #6-32 x %-Inch Pan Head Machine Screw 178070-001 Volume Control Knob

3-15

Page 40

Illustrated Parts Lists

170000-001 (Lamp)

179047-001 (Lamp Base)

99-15056 (Screw for Bezel)

99-15025 (Coin Inlet)

75-914S (Hex Nut)

(Lock Wash.)

(Switch)

  • a 9915023 (Base Plate)

T24414S (Screw)

Figure 3-10 Vertically Mounted Coin Door 171034-xxx A

3-16 (Coin Return Box) Food Fight

th

al.

Page 41

Food Fight

A037542-01 (Harness—not shown)

99-15063 (Screw)

99-15067 (Lock Assy) Illustrated Parts Lists

(Lock Assy.) 99-15038 (Bezel for Button)

99-15001 thru 99-15011 (Return Button)

(Spring for Button)

99-15071 (Clamp)

038091-01 (Coin Box) 99-15066 (Screw)

a oo

9946072 (Door Frame)

99-15073, 99-15070 (Upper Door) | (Doors and Frame) 99-15074 (Lower Door)

171034-001 — U.S. 25¢/25¢ Coin Door 171034-006 — U.K. 20 P/50 P Coin Door 171034011 — German 1 DM/5 DM Coin Door 171034-003 — Canadian 25¢/25¢ Coin Door 171034-008 — German 2 DM/1 DM Coin Door 171034-015 — French 2 Frit Fr Coin Door 171034-005 — U.K. 10 P/50 P Coin Door 171034-010 — German 2 DM/S DM Coin Door

Figure 3-10 Vertically Mounted Coin Door, continued 171034-xxx A

Page 42

Illustrated Parts Lists

Vertically Mounted Coin Door Parts List

Part No. Description

A037542-01 Harness Assembly 72-14148 #4-40 x 7%-Inch Cross-Recessed Pan-Head Steel Machine Screw 75-056 #6 Internal-Tooth Zinc-Plated Steel Lock Washer 75-9148 #4-40 Steel Machine Hex Nut

75-34148 #4-4) x %-Inch 82° Cross-Recessed Flat-Head Steel Machine Screw 99-15001 Coin Return Button with U.S. 25¢ Price Plate 99-15002 Coin Return Button with U.S. $1 Price Plate 99-15003 Coin Return Button with German | DM Price Plate

99-15004 Coin Return Button with German 2 DM Price Plate 99-15005 Coin Return Button with German 5 DM Price Plate 99-15006 Coin Return Button with Belgian 5 Fr Price Plate 99-15007 Coin Return Button with French | Fr Price Plate

99-15008 Coin Return Button with Japanese 100 Yen Price Plate 99-15009 Coin Return Button with British 10 Pence Price Plate 99-15010 Coin Return Button with Australian 20¢ Price Plate 99-15011 Coin Return Button with Italian 100 Lire Price Plate

99-15023 Base Plate 99-15025 Left Half of Coin Inlet 99-15026 Right Half of Coin Inlet 99-15027 Side Plate of Coin Return Box

99-15028 Base Plate of Coin Return Box 99-15029 Switch Bracket 99-15036 Metal Coin Return Cover 99-15038 Bezel for Coin Return Button 99-15039 Metal Bezel for Coin Return Cover 99-15040 Coin Return Lever 99-15042 Coin Switch for U.S. 25¢ 99-15052 Spring for Coin Return Button

99-15054 Pivot for Coin Return Lever 99-15055 Retaining Screw 99-15056 #4-40 x 9%¢-Inch Cross-Recessed Pan-Head Steel Machine Screw 99-15060, Switch Cover

99-15063 Screw for Hinge 99-15066 Screw for Clamp 99-15067 Lock Assembly 99-15070 Doors and Frame

99-15071 Clamp for Frame 99-15072 Door Frame 99-15073 Upper Door 99-15074 Lower Door

99-15075 Switch Adjuster 038091-01 Coin Box (Not included in assembly—Acceptable substitute is part number A037491-01) 170000-001 6.3 V Miniature Wedge-Base Incandescent Lamp 171006-035 Metal Coin Mechanism 179047-001 Lamp Base

3-18 ak

Page 43

Ulustrated Parts Lists Food Fight

171006-035 9910140 (Coin mechanism) (Panel assy}

75-9485 -— (Locknut) a 99-10116 (Lever)

99-10152 (Right coin inlet).

(Fastener) 75-9448 (Locknut)

9910151 (Left coin iniet)

99-11 (Lamp oN 70-11-47 ; (Lamp) so go &

/ 99-10108 | (Bar retainer) Screw) i 98-10147 (Hamess)

98-10154 Z (racket assy)

99-10042 thru 99-10045 99-10153 (Coin switch assy.) (Coin return box)

Ss e54gic (Coin switch) A A oN 7 (Switch cover)

99-10075 thru 99-10078 (Switch wire) 98-1008 7514128 (Retainer) (Screw)

Figure 3-11 American-Made Coin Door Assembly 171027-001 A

Page 44

Food Fight Illustrated Parts Lists

99-10148 (Lock assy.)

9910142 (Button housing)

99-10134 (Cover)

99-10115 (Spring) 99-10119 (Button assy) 99-10118 (Button)

99-10141 (Coin return cover)

99-1017 (Coin return door)

19-10149 (Service door)

Cee

99-10143 (Frame) 99-10139 (Coin door) —>|

(Cam) 99-10145 —>(

038091-01 (Coin box) oe ee

171034-011 — German 1 DW5 DM Coin Door 171034015 — French 2 Fifi Fr Coin Door

  • German 2 DM/1 OM Coin Door 171034010 — German 2 DM/5 DM Coin Door 171034-008 — U.K. 20 P/50 P Coln Door 171034-009 171034-001 — U.S. 25¢/25¢ Coin Door 171034-003 —- Canadian 25¢/25¢ Coin Door 171034-005 — U.K. 10 P/50 P Coin Door

Figure 3-11 American-Made Coin Door Assembly, continued 171027-001 A

3-20

Page 45

Food Fight Illustrated Parts Lists

American-Made Coin-Door Assembly

Parts List

Part No. Description

171906-035 Metal Coin Mechanism for U.S. 8.25 65-441C Coin Switch 70-11-47 Miniature Bayonet Lamp 72-94068 #4-40 x 34-Inch Truss-Head Screw

72-HAI404C #4-40 x '4-Inch Pan-Head Screw 72-JA1405B #4-40 x .31-Inch Pan-Head Screw 75-1412 #4-40 x ¥4-Inch Pan-Head Screw 75-9448 #4-40 Locknut

99-10008 Retainer 99-10042 Coin Switch Assembly for Belgian 5 Fr and U.S. $.25 99-10043 Coin Switch Assembiy for German 1 DM, Japanese 100 Yen, Swiss | Fr 99-10044 Coin Switch Assembly for German 2 DM, Italian 100 L, U.S, $1.00 99-10045 Coin Switch Assembly for Australian $.20, German 5 DM, British 10 P 99-10068 Coin Return Chure 99-10075 Switch wire (included in coin switch assembly) 99-10076 Switch wire (included in coin switch assembly) 99-10077 Switch wire (included in coin switch assembly) 99-10078 Switch wire (included in coin switch assembly) 99-10080 Lamp socket 99-10081 Key holder

99-10096 Fastener 99-10104 Bar retainer 99- 10105 Bar 99-AOLIS Spring

99-10116 Plastic Coin Return Lever 99-10117 Steel Coin Return Door 99-10118 Amber Coin Return Button 99-10119 Amber Coin Button for U.S. $.25 99-10134 Coin Button Cover 99-10139 Coin Door 99-10140 Coin Door Inner-Panel Assembly 99-10141 Diecast Coin Return Cover

99-10142 Diecast Button Housing 99-10143 Coin Door Frame 99-10144 Coin Door Channel Clip 99-10345 Offset Cam

99-10146 Coin Inlet Chute Assembly 99-10147 American-Made Coin Door Harness 99-10148 Lock Assembly 99-10149 Service Door

99-10150 Switch Cover 99-AO15L Left Coin Inlet 99-10152 Right Coin Inlet 99-10153 Coin Return Box 99-10154 Bracket Assembly

3-21

Page 46

Illustrated Parts Lists Food Fight

72-1604F (Screw)

176015-110 (Screw) 03787301 (Spacer) 4

EMI Shield PCB

jo ° [ | aN ° 72-1404F 5 (Screw) i eo

‘403770102 (Cage)

175009-221 EMI Shield PCB (Washer) See Figure 3-13 178044-242 mien Gi ame (rammet} 178045-442

(Fastener)

72.6810S 175004-708 175004-708 (Screw) (Washer) (Washer)

034536-02 (Foam pad)

(Screw)

A035435-04 egulator/ Audio II PCB)

NOTE

Within the U.S. the FCC requires that the game PCB be housed in the EMI cage with the Shield PCB attached.

Figure 3-12 Electromagnetic Interference (EMI) Cage Assembly and Printed-Circuit Board Mounting Hardware

3-22

Page 47

On

a Food Fight

EMI Cage Assembly and Printed-Circuit Board Mounting Hardware Parts List Illustrated Parts Lists

Part No. Description

A0Q37701-02 A037430-04 72-1404F 72-1004F

037873-01 175004-708 175009-221 176015-110

178044-242 178045-442 179125-001

034536-02 175004-708 72-68108 US-Built Game

EMI Cage (includes guide) EMI Shield PCB #4-40 x %-Inch Cross-Recessed Steel Screw 46-32 x %4-Inch Cross-Recessed Steel Screw

Spacer #8 Flat Fiber Washer Plastic Washer #10 x %-Inch Cross-Recessed Pan-Head Screw

Grommet Snap-In Fastener Grounding Clip (not shown)

freland-Built Game

Foam Pad #8 Flat Fiber Washer #8 x %-Inch Cross-Recessed Pan-Head Screw

3-23

Page 48

Illustrated Parts Lists

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING FIDENTIAL: Reproduction forbidden without the speci Inc., Sunnyvale, CA. This drawing is only conditionally issued, and neither receipt nor possession there: of Confers or transfers any right in, of license t0 use, the subject matter of the drawing or any design or technical information show thereon. no any right to reproduce this drawingorany part thereof. Except for manufacture hy yendors of Atari, Inc., and for manufacture under the corporation’ written license, no right (©, reproduce this drawing is granted or tbe subject matter thereof luntess by written agreement with of written permission from the corporation.

Figure 3-13 EMI Shield PCB Assembly

3-24 g R Hd dl

eaueeeeesgeggd ae TT

A040253-01 A Food Fight

aan

Page 49

Ow Food Fight Illustrated Parts Lists

EMI Shield PCB Assembly Parts List

DesignatorDescriptionPart No.

Capacitors

C1-C30.1 pF, +80% -20%, 50 V Ceramic-Disk Capacitor122002-104
cs0.1 uF, +80% -20%, 50 V Ceramic-Disk Capacitor122002-104
C6-C81000 pF, +5%, 100 V, NPO Ceramic-Disk Axial-Lead Capacitor (Acceptable122016-102

substitute is part no. 122002-102)

C9-C11470 pF, 100 V, NPO Ceramic-Disk Axial-Lead Capacitor(Acceptable122016-471

substitute is part no, 122013-471)

C12-C200.01 uF, +80% -20%, 25 V Ceramic-Disk Axial-Lead Capacitor122005-103
C21, C220.1 uF, +80% -20%, 50 V Ceramic-Disk Capacitor122002-104
C€24-C300.1 uF, +80% -20%, 50 V Ceramic-Disk Capacitor122002-104
C31-C390.01 pF, +80% -20%, 25 V Ceramic-Disk Axial-Lead Capacitor122005-103
C40O.1 uF, +80% -20%, 50 V Ceramic-Disk Capacitor122002-104

Connector

P2044-Pin Card-Edge Connector (Acceptable substitute is part no. 179046-044)179073-044

3-25

Page 50

Food Fight Illustrated Parts Lists

. *

  • co a o oo 32 372n1 ie72an rey Fi as - 501 “cot fae) Smeal 02 etl Eres S87 of Ta7Zi1 (B72 =

i -oo! O01 bisz72] mre erry 57] Gal

gy [aeszs] [aceze ac] (2xo2 | [oxor Eat Seue] se Seal Se au 2 Boo 7 TBeoe ‘ ac Sar] ("tees Brae Bae Se'| Ges) sex py TE

ese za eS 3. mes & Sb ea iB@o020| [BeOZo aed Be 2N3904 =xow | f -ros er Gans Lox e295] See] Sisal [iBeoz5] [12e0z0 EI (-xo8 | [-,07 2a eae eer rer Sec}

ij a2as| 9 (5285) Se? Ssa77 Stax) ber] pmor uv 2: fiszas] f) [seas] ‘ = fe} li Sz ae] ee Sisal z

  • =o ~ Tersr) ear) Sa7] Sesa] of} Sera] 147289-52 . Booze) Ee ies] erry eon 6% eh “209 | sae Moses Bae [oar Bez ae] are) aa =e] S 7 a

xo = pa = sar] Ss faae7] =r73) Ta37] fo Rae] er) Er)

eee =a] ia] feo Se] 75] 28] con OS) sez ae cus = 10 9 8 6 5 4 3 2 1

A Figure 3-14 Food Fight Game PCB Assembly A039445-21

3-26

Page 51

Food Fight

Food Fight Game Printed-Circuit Board Assembly Mlustratedl Parts Lists

Parts List

DesignatorDescriptionPart No.

Capacitors

ClO.1 HE, +80%, -20%, 50 V, Ceramic Capacitor122002-104
c239 pE, 100 V Minimum, Dipped, Fixed-Mica Capacitor128002-390
C3100 pF. 100 V Minimum, Dipped, Fixed-Mica Capacitor128002-101
C4O.1 pF, +80%, -20%, 50 V, Ceramic Capacitor122002-104
C5-C39O.L uF, +80%, -20%, 50 V, Ceramic Capacitor122002-104
C40-C47O.1 uF, +80%, -20%, 50 V, Ceramic Capacitor122002-104
C48, C49O.1 pF, +80%, -20%, 50 V, Ceramic Capacitor122002-104
C50-C52O.1 AF, +80%, -20%, 50 V, Ceramic Capacitor122002-104
C53-C550.015 uF, + 10%, 100 V, Radial-Lead Mylar Capacitor21-101153
C560.001 EF, + 10%, 100 Y, Radial-Lead Mylar Capacitor21-101102
C57100 wF, 35 V Aluminum Electrolytic Axial-Lead Capacitor24-350107
C58, C59O.L MF, +80% -20%, 50 V, Ceramic Capacitor122002-104
C60120 pE, 100 V Mica Capacitor128002-221
C90100 pF, 35 V Aluminum Electrolytic Axial-Lead Capacitor24-350107

Diodes

CRIType-MV5053 Light-Emitting Diode38-MV5053
CR2Type-IN7564, + 5%, 500 mW, 8.2 V Zener Diode32-IN756A

Inductors

Li100 wH, + 10% Inductor141002-001
L2-L41pH, + 10%, 830 mA, 0.29 Q, Peaking Coil Inductor141007-001

Integrated Circuits

IE‘Type-74LS74 Integrated Circuit37-TALS74
IF‘Type-74L$86 Integrated Circuit37-TALSB6
1H‘Type-7407 Integrated Circuit37-7407
1KType-74LS74 Integrated Circuit37-74LSTA
IL‘Type-74804 Integrated Circuit37-7AS04
1M‘Type-74LS163A Integrated Circuit37-TALS1O3A
INType-741S163A Integrated Circuit37-7ALSI63A,
IP‘Type-74LS175 integrated Circuit37-7ALS175
2B‘Type-74LS02 Integrated Circuit37-74L802
2CType-74S08 Integrated Circuit37-74808
2DType-748157 Integrated Circuit37-748157
2B‘Type-74LS08 Integrated Circuit37-74LS08
2FType-74LS21 Integrated Circuit137210-001
2H‘Type-74L874 Integrated Circuit37-74LS74
za‘Type-74L$32 Integrated Circuit37-7ALS32
2K‘Type-74LS74 Integrated Circuit37-74LS74
2LType-74LS163A Integrated Circuit37-TALS163A
2M‘Type-74LS163A Integrated Circuit37-TALS1G3A,
2N‘Type-74LS 163A Integrated Circuit37-74LS163A
2PPROM Integrated Circuit136020-112

(Continued on next page)

3-27

Page 52

Illustrated Parts Lists Food Fight

Food Fight Game Printed-Circuit Board Assembly Parts List, continued

DesignatorDescriptionPart No.
3AType-74LS157 Integrated Circuit37-74LS157
3BType-74LS 157 Integrated Circuit37-74LS 157
3cType-74LS 174 Integrated Circuit37-74LS174
3DType-74LS299 Integrated Circuit137180-001
3EType-74L$299 Integrated Circuit137180-001
3FType-74L$283 Integrated Circuit137204-001
3HType-74LS21 Integrated Circuit137210-001
3)Type-74LS245 Integrated Circuit37-74LS245
3PType-74LS157 Integrated Circuit37-74LS157
4AType-74S163 Integrated Circuit137274-001
4BType-745163 Integrated Circuit137274-001
4CType-74LS86 Integrated Circuit37-74LS86
4FType-74LS273 Integrated Circuit37-74LS273
4HType-74LS283 Integrated Circuit137204-001
4‘Type-74LS86 Integrated Circuit37-74LS86
4KType-74L5367 Integrated Circuit37-74L8367
4LType-74LS157 Integrated Circuit37-74LS157
4MType-74LS157 Integrated Circuit37-74LS157
4N‘Type-74LS157 Integrated Circuit37-74LS157
4PType-74S00 Integrated Circuit37-74S00
5AType-74S 163 Integrated Circuit137274-001
5BType-745 163 Integrated Circuit137274-001
5HType-74LS377 Integrated Circuit37-74LS377
5)Type-74L8245 Integrated Circuit37-74L8245
5KType-74LS273 Integrated Circuit37-74L8273
5LType-74LS273 Integrated Circuit37-74LS273
5MType-74LS194 Integrated Circuit37-74LS194
5NType-74LS 194 Integrated Circuit37-74LS194
5PType-74L$32 Integrated Circuit37-74LS32
6BType-74LS273 Integrated Circuit37-74LS273
6HType-74LS 157 Integrated Circuit37-74LS157
0‘Type-74LS157 Integrated Circuit37-74LS157
6KType-74LS273 Integrated Circuit37-74LS273,
6NType-74LS257 Integrated Circuit37-74LS257
oPType-74LS257 Integrated Circuit37-74LS257
TKILType-74LS273 Integrated Circuit37-74LS273
7MType-74LS273 Integrated Circuit37-74LS273
8K/LMicroprocessor Integrated Circuit137289-001
8MType-74LS244 Integrated Circuit37-T4LS244
8N/P‘Type-74L8244 Integrated Circuit37-74L8244
8HType-74LS245 Integrated Circuit37-74LS245
8HType-74LS245 Integrated Circuit37-74LS245
8pType-74L802 Integrated Circuit37-7ALSO2
oHType-74LS245 Integrated Circuit37-74LS245

(Continued on next page)

3-28

Page 53

Food Fight

Food Fight Game Printed-Circuit Board Assembly Parts List, continued Mlustrated Parts Lists

DesignatorDescriptionPart No.
oH)Type-741.8245 Integrated Circuit37-TALS245
OK/LMicroprocessor Integrated Circuit137289-001
OMType-74LS244 Integrated Circuit37-7ALS244
opType-74LS00 Integrated Circuit37-74LS00
10)/K‘Type-74LS 14 Integrated Circuit37-74LS14
10CType-7406 Integrated Circuit37-7406
10EType-74LS32 Integrated Circuit37-74LS32
10C/D‘Type-74LS138 Integrated Circuit137177-001
10D‘Type-74LS 138 Integrated Circuit137177-001
10H)‘Type-74L832 Integrated Circuit37-7ALS32
10H‘Type-74L874 Integrated Circuit37-TALS74
1OFType-74LS74 Integrated Circuit37-TALS74
10MType-74LS161 Integrated Circuit37-74LS161
10NType-74LS161 Integrated Circuit37-74LS161
10PProgrammed Logic Array Integrated Circuit137313-001
1IC/DType-74LS273 Integrated Circuit37-T4LS273
rte)Type-74L$244 Integrated Circuit37-TALS244
HEType-74L8244 Integrated Circuit37-74L8244
1/12yQuad Op-Amp Integrated Circuit37-LM324
JIK/LCustom I/O Integrated CircuitC012294-01
1IL/M.Custom I/O Integrated CircuitC012294-01
I1INCustom I/O Integrated CircuitC012294-01
12DD-to-A Converter Integrated Circuit137243-001

Miscellaneous

Q2, Q3Nylon Snap-In Fastener81-4302

Test Point (Acceptable substitute is part no. 020670-01) 17905 1-002

Yi12.096 MHz Crystal144000-001
SWI8-Station Single-Throw Dual-Inline Package Bit Switch66-118P1T.

Erasable Programmable Read-Only Memories

4DErasable Programmable Read-Only Memory136020-110
4EErasable Programmable Read-Only Memory136020-111
6LIMErasable Programmable Read-Only Memory136020-109
8CErasable Programmable Read-Only Memory136020-101
8DErasable Programmable Read-Only Memory136020-103
BEErasable Programmable Read-Only Memory136020-105
8FErasable Programmable Read-Only Memory136020-107
9cErasable Programmable Read-Only Memory136020-102
9DErasable Programmable Read-Only Memory136020-104
9EErasable Programmable Read-Only Memory136020-106
oFErasable Programmable Read-Only Memory136020-108

Random-Access Memory

3KStatic RAM Integrated Circuit90-7036
3LStatic RAM Integrated Circuit90-7036
3MStatic RAM Integrated Circuit90-7036
3NStatic RAM Integrated Circuit90-7036

(Continued on next page)

3-29

Page 54

Illustrated Parts Lists Food Fight

Food Fight Game Printed-Circuit Board Assembly Parts List, continued

DesignatorDescriptionPart No.
5cRandom-Access Memory137178-001
5DRandom-Access Memory137178-001
SERandom-Access Memory137178-001
SFRandom-Access Memory137178-001.
6cRandom-Access Memory137250-001
6DRandom-Access Memory137250-001
GERandom-Access Memory137250-001”
OFRandom-Access Memory137250-001
JNRandom-Access Memory137178-001
7PRandom-Access Memory137178-001
8ARandom-Access Memory137211-001
8BRandom-Access Memory137211-001
9ARandom-Access Memory137211-00i
OBRandom-Access Memory137211-091
ONNon-Volatile RAM Integrated Circuit137288-001

Resistors

RL220 Q, +5%, %& W Resistor110900-221
R2, R310 kQ, +5%, % W Resistor119000-103
R41kQ, +5%, % W Resistor110000-102
RS-R71kQ, +5%, 4 W Resistor110000-102
R81kQ, +5%, % W Resistor110000-102
RO1kQ, +5%, % W Resistor110000-102
RIO1kQ, +5%, 4 W Resistor110000-102
Ril470 Q, +5%, 4 W Resistor110000-471
R121kQ, +5%, %& W Resistor110000-102
R13, R14220 2, +5%, 4 W Resistor110000-221
RIS470 Q, 45%, Y%4 W Resistor110000-471
RIO1kQ, +5%, 4% W Resistor110000-102
RI7470 Q, +5%,W Resistor110000-471
RIS220 Q, +5%, 4 W Resistor110000-221
RIO1kQ, +5%, % W Resistor110000-102
R20-R23,1kQ, 45%, %& W Resistor110000-102,
R24-R274.7kQ, +5%, Ys W Resistor110000-472
R28220 Q, 5%, 4 W Resistor110000-221
R29220 Q, £5%, % W Resistor110000-221
R301kQ, £5%, % W Resistor110000-102
R31470 Q, +5%, “%& W Resistor110000-471
R321kQ, +5%, 4 W Resistor110000-102
R33470 Q, +5%, v4 W Resistor110000-47 1«
R341kQ, +5%, %4 W Resistor110000-102
R35,470 Q, 45%, 4 W Resistor110000-471
R361kQ, +5%, %& W Resistor110000-102,
R37470 Q, +5%, %4 W Resistor110000-471
R381kQ, +5%, % W Resistor110000-102

(Continued on next page)

3-30

Page 55

Food Fight

Food Fight Game Printed-Circuit Board Assembly Parts List, continued Illustrated Parts Lists

DesignatorDescriptionPart No.
R39470 Q, +5%, 4 W Resistor110000-471
R401kQ, +5%, % W Resistor110000-102
R41470 Q, +5%, 4 W Resistor110000-471
R421kQ, +5%, % W Resistor110000-102
R43470 Q, +5%, 4 W Resistor110000-471
R441kQ, +5%, % W Resistor110000-102
R45470 Q, +5%, 4 W Resistor110000-471
R4610kQ, +5%, 4% W Resistor110000-103
R47-R49100 kQ, +5%, 4 W Resistor110000-104
R50-R574.7kQ, +5%, %4 W Resistor110000-472
R5810kQ, +5%, 4 W Resistor110000-103
R59-621kQ, +5%, % W Resistor110000-102
R63-R6710 kQ, +5%, ¥%4 W Resistor110000-103
R6822 kQ, +5%, 4 W Resistor110000-223
R69-R71330k, +5%, % W Resistor110000-334
R72-R74910 Q, +5%, 4 W Resistor110000-911
R75,220 Q, +5%, % W Resistor110000-221
R761kQ, +5%, % W Resistor110000-102
RI7220 2,5%, 4 W Resistor110000-221
R784.7kQ, +5%, Y% W Resistor110000-472
R79330 Q, +5%, ¥4 W Resistor110000-331
R90, ROL4.7kQ, +5%, 4 W Resistor110000-472
R2071kQ, 45%, %& W Resistor110000-102

Sockets

4D28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
4E28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
5c22-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C22
5D22-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C22
SE22-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C22
SF22-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C22
6c22-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C22
6D22-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C22
6E22-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C22
OF22-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C22
OL/M28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
7N22-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C22
7P22-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C22
8A24-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C24
8B24-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C24
8C28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
8D28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
8E28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
8F28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
8K/L64-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C64

(Continued on next page)

Page 56

Illustrated Parts Lists Food Fight

Food Fight Game Printed-Circuit Board Assembly

Parts List, continued

DesignatorDescriptionPart No.
OA24-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C24
OB24-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C24
9C28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
9D28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
9E28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
oF28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
OK/L.64-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C64
10P20-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C20
1IK/L.40-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C40
1IL/M40-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C40
11N40-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C40
12D28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28

Transistors

aiType-2N3904, 350 mW, 60 V NPN Transistor34-2N3904
Q2, @Type-2N6044, 8 A, 80 V NPN Transistor34-2N6044
Q4Type-2N3904, 350 mW, 60 V NPN Transistor34-2N3904

3-32 eed

Page 57

Food Fight

NOTICE TO ALL, PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbitlden without the specific ‘wrigen permission oF Atari Ine, Suanyvale, CA. This drawing is nly conitionally issued, and’ neither receipt nor possession thereof confersor tcansfers any rightin, oF license 0 use, the sub

ject matter ofthe drawing or any desiga or echnical information

shown thereon, nor any night (0 reproduce this drawing or any part thereof, Except for manufacture by vendors of Atar, Inc, and for manufgeture under the corporation's written license, no {ight 9 reproduce this Grawing is granted or the subject matter thereof unless by written agreement with or weliten permission from the corporation, Iustrated Parts Lists

[o) 33 > rea, 7h O

TiP32 TOAZ 002 A Toazo02a— | & Q2 inscoz Q5 Orr af cR4 t 1 Ho i RSet ee C7 S creat 33IRS <| Ce) = |,,o| cist ee y7,_[220 Leet, vew cle yh 4S +} oR encif] CATR

Our + Raa

Figure 3-15 Regulator/Audio II PCB Assembly A035435-04 K

3-33

Page 58

Ilustrated Parts Lists Food Fight

Regulator/Audio IJ PCB Assembly Parts List

DesignatorDescriptionPart No.

Capacitors

cl470 uF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-250477
C20.001 pF, 50 V, Ceramic-Disc Axial-Lead Capacitor122002-102
C30.1 uF, 50 V, Ceramic-Disc Axial-Lead Capacitor122002-104
C4470 pF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-250477
cs0.01 pF, 25 V Minimum, Ceramic-Disc Axial-Lead Capacitor (Acceptable100015-103

substitute is part no, 122005-103)

C60.22 pF, 25 V, Ceramic-Disc Axial-Lead Capacitor122004-224
c70.001 uF, 50 V, Ceramic-Disc Axial-Lead Capacitor122002-102
c80.22 pF, 25 V, Ceramic-Disc Axial-Lead Capacitor122004-224
C9, C103300 pF, 35 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-350338
cll0.1 uF, 50 V, Ceramic-Disc Axial-Lead Capacitor122002-104
C12470 uF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-250477
cia1000 pF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-250108
C140.01 wE, 25 V Minimum, Ceramic-Disc Axial-Lead Capacitor100015-103

(Acceptable substitute is part no. 122005-103)

cis0.22 pk, 25 V, Ceramic-Disc Axial-Lead Capacitor122004-224
C160.001 pF, 50 V, Ceramic-Disc Axial-Lead Capacitor122002-102
cl70.22 wR, 25 V, Ceramic-Disc Axial-Lead Capacitor122004-224
C18, C193300 pF, 35 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-350338
C20, C210.1 pF, 50 V, Ceramic-Disc Axial-Lead Capacitor122002-104

Diodes

CRI, C4Type-1N4002, 1 A, 100 V Silicon Rectifier Diode31-1N4002
CR5-CR8BType-1N5401, 3 A, 100 V Silicon Rectifier Diode31-1N5401

Integrated Circuits

QlType-LM305, 5 Y, Linear Voltage Regulator37-LM305,
as‘Type-TDA2002A, 8 W, Linear Audio Amplifier Integrated Circuit137151-002
Q‘Type-TDA2002A, 8 W, Linear Audio Amplifier Integrated Circuit137151-002

Resistors

RL2702, 5%, %& W Resistor110000-271
R333 Q, +5%, 4 W Resistor110000-330
R4100 2, £5%, % W Resistor110000-101
RS2.7Q, +5%, 1 W Resistor110009-027
RO3.9 kQ, +5%, Ys W Resistor110000-392
R77.5 kQ, +5%, % W Resistor110000-752
R81 kQ Horizontal PCB-Mounting Cermet Potentiometer (Acceptable119002-102

substitute is part no. 19-315102)

RO220 Q, +5%, % W Resistor.110001-221
R101Q, £5%, % W Resistor110000-010
RI10 Q, +5%, % W Resistor110000-100
RI2100 2, +5%, % W Resistor110000-101
RL, R1410 kQ, +5%, % W Resistor110000-103

3-34 (Continued on next page)

Page 59

Food Fight Mlustrated Parts Lists

Regulator/Audio II PCB Assembly Parts List, continued

DesignatorDescriptionPart No.
RID1Q, +5%, 4 W Resistor{10000-010
R2010 2, 45%, & W Resistor110000-100
R21220 2, +5%, Ye W Resistor110001-221
R22100 2, +5%, 4 W Resistor110000-101
R240.12, +3%, 7 W Wirewound Resistor19-100P 1015,
R27, R281kQ, +5%, 4 W Resistor110000-102
R29, R3010 2, +5%, 4 W Resistor110000-100
R32, R335.6 kQ2, +5%, % W Resistor110000-562

Transistors

Q2Type-TIP32 PNP Power Transistor33-TIP32
Q3Type-2N3055 NPN Silicon Transistor34-2N3055

Mechanical Parts

JO6-Position Connector Receptacle79-58306
J79-Position Connector Receptacle79-58308
184-Position Connector Receptacle7958354
JO6-Position Connector Receptacle79-58306
Jlo12-Position Connector Receptacle79-58346
Q2#6-32 x 14-Inch Binder-Head Nylon Screw75-F60405
3#6-32 Nut/Washer Assembly75-99516
Q3Thermally Conductive Silicon Insulator78-16008
QsThermally Conductive Silicon Insulator78-16008
Q5, Q7#6 x ¥-Inch Cross-Recessed Pan-Head Thread-Forming ‘Type-AB Zinc-72-56606S

Plated-Steel Screw

Heat Sink 034531-01 Test Point (Acceptable substitute is part no. 020670-01) 17905 1-001

3-35

Page 60

Food Fight IMustrated Parts Lists

WARNING Fuse block cover must be in place during game operation. (A035888-01 (Transtormer assy.)

A021084-xx, (Voltage plugs)

29-053 (Capacitor) 03454401 (Fuse block cover)

78-70501SC (Capacitor bracket) hy ‘A035801-02 034482.02 wa (Chassis)

78-2708 (Bushing) < SS NY A034630-01 79-3206 ~ (Filter Assy.)

(Fuse block) 462014002 (Fuses)

N 79-15021001 >> ‘A035890-01 (Terminal block) (Power harness)

A034629-01 Beet © (AC harness) (Rectifier)

Figure 3-16 Color Raster-Scan Power Supply Assembly A037671-01 &-03 H

3-36

Page 61

Food Fight

Power Supply Assembly Parts List US-Built Game A037671-01 G Illustrated Parts Lists

DesignatorDescriptionPart No.
cL27,000 pF, 15 VDC Electrolytic Capacitor29-053
cl2-Inch Diameter Capacitor Mounting Bracket78-70501SC
CRIType-MDA 3501 Bridge Rectifier3A-MDA35O1
FlPanel-Mounting Non-Indicating 3AG Curtridge-Type Fuse Post79-441101
Fl7 A, 250 V, 3AG Slow-Blow Glass Cartridge-Type Fuse46-201 7002
FlLabel for Fuse Value037639-01
F24 A, 250 V, 3AG Slow-Blow Glass Cartridge-Type Fuse4G6-2014002
F2-F65-Position 3AG Fuse Block with 4-Inch Quick-Disconnect Terminals79-3206
F2-F6Fuse Harness AssemblyA035891-02
F2-F6Fuse Block Cover034544-01
F2-FOLabel for Fuse Values037640-01
F320 A, 32 V, 3AG Slow-Blow Glass Cartridge-Type Fuse46-301203
F42-Circuit Single-Row Terminal Block (located under F4)79-15021001
F4-F64 A, 250 V, 3AG Slow-Blow Glass Cartridge-Type Fuse46-2014002
FLIRFI Filter Assembly (designation not marked)A034630-01
RPower Harness AssemblyA035890-01
iBVoltage Plug for 120 V (105-135 VAC) (yellow wite color—plugs into J3)A021084-02
J4aAC Harness AssemblyA034629-01
Ti‘Transformer Assembly (designation covered—Acceptable substitute js part no.A035888-01

A035888-02) Nylon Type 6/6 Hole Bushing with %Inch Inside Diameter x *%-Inch 78-2708 Outside Diameter x %-Inch Thick

Power Supply Chassis Base 034482-02 Metal Base Piate (not shown in illustration) 037243-01

Page 62

Illustrated Paris Lists

Power Supply Assembly Parts List Ireland-Built Game A037671-03 G Food Fight

DesignatorDescriptionPart No.
cl27,000 pF, 15 VDC Electrolytic Capacitor29-053,
cl2-Inch Diameter Capacitor Mounting Bracket78-70501SC
CRIType-MDA 3501 Bridge Rectifier3A-MDA3501
FIPanel-Mounting Non-Indicating 3AG Cartridge-Type Fuse Post79-441101
FILabel for Fuse Value037639-02
FI, F24 A, 250 V, 3AG Slow-Blow Glass Cartridge-Type Fuse46-2014002
F2-F65-Position 3AG Fuse Block with 4 -Inch Quick-Disconnect Terminals79-3206
F2-F6Fuse Harness AssemblyA035891-02
F2-F6Fuse Block Cover034544-01
F2-F6Label for Fuse Values037640-01
F320 A, 32 V, 3AG Slow-Blow Glass Cartridge-Type Fuse46-301203
F42-Circuit Single-Row Terminal Block (located under F4)79-15021001
F4-F64 A, 250 V, 3AG Slow-Blow Glass Cartridge-Type Fuse46-2014002
FLLRFI Filter Assembly (designation not marked)A034630-01
j2Power Harness AssemblyA035890-01
3BVoltage Plug for 220 V (200-240 VAC) (blue wire color—plugs into J3)A021084-04
J3Voltage Plug for 240 V (220-260 VAC) (brown wire color—plugs into J3)A02 1084-05
JaaAC Harness AssemblyA034629-01
TlTransformer Assembly (designation covered—Acceptable substitute is part no.A035888-01

A035888-02) Nylon Type 6/6 Hole Bushing with %-inch Inside Diameter x 5%4-Inch 78-2708 Outside Diameter x %4-Inch Thick

Power Supply Chassis Base 034482-02 Metal Base Plate (not shown) 037243-01

Page 63

Gimbal Joystick Maintenance and Repair

WARNING Before removing or repairing the joystick, turn the game off.

Normal maintenance involves lubricating four parts in the joystick control approximately every three months (this requires removing the control). First, open the control panel. Tilt the control panel towards you. Then unsolder the harness from the two potentiometers on the joystick assembly. From the inside of the control panel, remove the four flat washers, hex nuts, and carriage bolts that mount the joystick to the control panel. Then open up the joystick control assembly by removing the four flat washers, hex nuts, and long screws (see Figure 3-4). At this point, most of the parts should disassemble.

Appendix A

For lubrication, use only Nyogel 779 lubricant (Atari part no. 178027-001). Lubricate the following parts inside the control:

© — The ball pinned to the shaft and the ends of the pivot

pins that protrude from the ball. e The insides of the two black linkages, located on the potentiometer shafts. ¢ The insides of the two gimbals, where the bottom of the shaft wears against them. ¢ The sides of the pivot ball housings at the four holes where the gimbals are attached. If the bellows need replacing, remove both gimbals and the bellows cap. Slide the bellows off the bottom of the shaft. Slide the new bellows up over shaft. Reassemble the joystick control, and then reinstall it in the control panel. Reconnect the harness wires as shown in Figure 3-3. Make sure the right colors go to the tabs on the potentiometers. Refer to Chapter 2, Self-Test Menu, for instructions on how to recalibrate the joystick.

Page 64

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 65

Food Fight ™ Ist printing

YOUR COMMENTS, PLEASE!

Your comments will assist Atari in improving our publications. The comments are an important part of preparing for revisions of game manuals. Please write in the space below. No postage stamp is necessary if mailed in the U.S.A.

If you have any technical questions about certain ATARI games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.

Page: Comments:

Fill in if you wish a reply:

Name

Firm CO) Distributor

Address CO Operator

City State Zip O Other

Area Code _ Phone -

Page 66

First Fold

No postage necessary if mailed in the United States

BUSINESS REPLY MAIL

FIRST CLASS PERMIT NO, 1004 SUNNYVALE, CA

POSTAGE WILL BE PAID BY ADDRESSEE

Atari, Inc. Attn.: Field Service/Coin-Op Division P.O. Box 427 Sunnyvale, California 94086

Second Fold

word

a8po snp ode,

Page 67

a

YOUR COMMENTS, PLEASE!

Your comments will assist Atari in improving our publications. The comments are an important part of preparing for revisions of game manuals. Please write in the space below.

If you have any technical questions about certain ATARI games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.

Page: Comments:

Fill in if you wish a reply:

Name .

Firm O Distributor Address ~ Cl Operator

City Country D Other

Phone; Country Code Local Number Food Fight ™ Ist printing

Page 68

First Foid

Atari Ireland Limited Attn.: Field Service/Coin-Op Division

Tipperary Town, Ireland

Second Fold

OI

a8po spp adey

Page 69

pad prow

Page 70

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 71

PEG LWE, SRR GE GE YE EE SS SE ES

Warranty

Seller warrants that its printed-circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its video displays (in games supplied with displays) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment. None of the Seller's other products or parts thereof are warranted. If the products described in this manual fail to conform to this warranty, Seller’s sole liability shall be, at its option, to repair, replace, or credit Buyer’s account for such products which are returned to Seller during said warranty period, provided: {a) Seller is promptly notified in writing upon discovery by Buyer that said products are defective; (b)Such products are returned prepaid to Seller’s plant; and (c)Selier’s examination of said products discloses to Seller’s satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation, or improper testing. In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages. Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms herein, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller’s part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products by Seller.

The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to you and others. Be very cautious in using non-Atari-supplied components with our games, in order to insure your safety. Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories. Atari cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor.

Page 72

A

ATARI

ATARI, INC. 790 SYCAMORE DRIVE P.O, BOX 906 MILPITAS, CALIFORNIA 95035 408/942-3100 ¢ TELEX 35-7488