Night Driver TM-080 1st Printing
Night Driver (Atari, 1976) · Technical Manual · 72 pages · 27 sections · original scan
1st printing NIGHT (T DRIVER ths
Seller warrants that its printed circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its television monitors (in games supplied with monitors) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment. None of the Seller's other products or parts thereof are warranted.
lithe products described in this manual fail to conform to this warranty, Sellers’ sole liability shall be, at its option, to repair, replace, or credit Buyer’s account for such products which are returned to Seller during said warranty period, provided:
- Seller is promptly notified in writing upon discovery by Buyer that said products are defective;
- Such products are returned prepaid to Sellers’ plant; and
- Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation or improper testing.
Zone . In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages.
EXCEPT FOR ANY EXPRESS WARRANTY SET FORTH IN A WRITTEN CONTRACT BE- TWEEN SELLER AND BUYER WHICH CONTRACT SUPERSEDES THE TERMS OF THIS ORDER, THIS WARRANTY IS EXPRESSED IN LIEU OF ALL OTHER WARRANTIES EX- PRESSED OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTA- BILITY AND FITNESS FOR A PARTICULAR PURPOSE, AND OF ALL OTHER OBLIGA- TIONS OR LIABILITIES ON THE SELLER'S PART, AND IT NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR THE SELLER ANY OTHER LIABILITIES IN CONNECTION WITH THE SALE OF PRODUCTS UNDER THIS OR- DER.
This document is and contains confidential trade secret information of Atari, Inc.
This document is loaned under confidential custody for the sole purpose of operation, maintenance or repair of Atari equipment and may not be used by or disclosed to any person for any other purpose whatever, and remains the property of Atari, Inc.
Neither it nor the information it contains may be reproduced, used, or disclosed to persons not having a need to know consistent with the purpose of the loan, without written consent of Atari, Inc.
NIGHT DRIVER Operation, Maintenance and Service Manual
ATARI INC. 1265 BORREGAS AVENUE SUNNYVALE, CA 94086 408/734-5310 @ TELEX 35-7488
By the Publications Group, Engineering Department AM
ATARI Innovative leisure
All rights reserved. Copyright © 1976 by Atari, Inc. No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher.
For permission requests, write: ATARI INC. 1265 BORREGAS AVENUE SUNNYVALE, CA 94086 408/734-5310 ¢ TELEX 35-7488
Lithographed in the U.S.A.
Table of Contents
Subject Page
{. INTRODUCTION 1.1 Physical Description of Game 1 7.2. Summary of Game Play .... 1 ll. SPECIFICATIONS .. a3 2.1 General 3 2.2 Electrical 3 2.3 Environmental ... ee 3 2.4 Owner/Operator Options for Structuring of Game Play . 3 2.5. Accessories Available on Separate Order . 3 Il. DESCRIPTION OF OPERATION . 5 3.1 Functionai Description of Game . 5 3.2 General Information 3.2.1 Energizing the Game 3.2.2. TV Monitor 3.2.3. TV Monitor Picture 3.3 Game Sequence 2.0.6.6 ice te ce eee nee 5 3.3.1 Operating Modes 3.3.2 Attract Mode 3.3.3 Play Mode 3.4. Owner/Operator Options 3.4.1 Price/Time Per Game Options 3.4.2. Bonus/Track Difficulty Options 3.4.3. Volume Control Iv. THEORY OF OPERATION ... 4.1 General Comments .. 4.2. Components of the Microcomputer System . 4.2.1 Program PROMs 4.2.2 Page Zero Memory 4.2.3. Microprocessor 4.2.4 Tri-state Devices 4.3, Microcomputer SysteM . 0... 0.06 10 4.3.1 Program PROMs Enable 4.3.2 Page Zero Enable 4.3.3 Phase 2 4.3.4 Playfield and Roadway Address 4.4 Microcomputer Watchdog .... 1.0.0.0 c eee cent tn et n eee nW V. INSTALLATION INSTRUCTIONS ...... 5.1 Unpacking Instructions 5.1.1 Examination for Shipping Damage 5.1.2. Mechanical Inspection Verifying Operation of Interlock Switches ... Operation of Self-Test Feature 5.3.1 Activating the Self-Test Feature 5.3.2 Visual Check ae Wr
Table of Contents
5.3.3 Audio Check 5.3.4 Adjusting the Options 5.3.5 Game Play Operation Test 5.4 Troubleshooting Self-Test Failures ........ 666 e cece eevee 5.4.1 Visual Check Failures 5.4.2 Audio Check Failures VI. MAINTENANCE AND ADJUSTMENTS 6.1 Routine Maintenance 6.2. Adjustments on TV Monitor ... Vil. DISASSEMBLY AND ASSEMBLY .. 7.1 General Information 7.2 Removing and Installing the Night Driver PCB 7.3 Removing and Installing the TV Monitor . 7.4 Replacing the Steering Board PCB .... 7.5 Replacing the Black Light Tube ....... : Vill. TROUBLESHOOTING AND REPAIR 8.1 General Procedure .. 8.1.1 Identifying the Trouble Area 8.1.2 Locating the Trouble Cause 8.1.3 Correcting the Trouble Cause 8.1.4 Verifying Correct Game Operation 8.2 Test Equipment 0.6.6 c ccc tent teen ete ete 8.2.1 Basic Test Equipment 8.2.2 Optional Test Equipment 8.3 Specific Troubleshooting Information «00.6... .60 0.2.2 c cere eee ee 83.1 Coin Mechanism 8.3.2. TV Monitor IX. SCHEMATICS, DRAWINGS, AND PARTS LISTS
|. INTRODUCTION
1.1. PHYSICAL DESCRIPTION OF GAME Atari's Night Driver is a one-player driving game. The game is packaged in its own distinctively styled upright cabinet that rests directly on the floor. A 23-inch TV monitor is mounted in the top front of the cabinet, with the monitor viewing screen slightly tilted back from vertical. (Figures 7-1 and 7-2 in Section VII and drawing number A006264-01, in Section IX of this manual, provide external and sectional views of the game cabinet.) The TV monitor is covered with a Plexiglas panel.
Player-operated controls are mounted directly below the TV monitor viewing screen on the front of the game cabinet. The controls consist of a steering wheel, a four-speed gear shifter, an accelerator foot pedal, a three-position rocker switch, and a pushbutton. The rocker switch is labeled NOVICE TRACK, PRO TRACK, and EXPERT TRACK. The pushbutton switch is labeled START. Two speakers mounted at the front of the game cabinet provide game sound.
Two identical coin mechanisms are mounted on the lower front center of the game cabinet, below the steering and shifting controls. Either of these two mechanisms can initiate play. The cash box is located behind a locked access door to the coin mechanisms.
1.2. SUMMARY OF GAME PLAY The player's objective is to keep the car within the pylon boundaries of the track and to go as fast as. possible After the proper coins have been inserted in the coin mechanism, the choice of which track to be played should be made. The difficulty factor of the tracks is determined by the track select rocker switch. In other words, the PRO TRACK is more difficult than the NOVICE TRACK, and the EXPERT TRACK is more difficult than the PRO TRACK.
Once the determination of the desired track is made, a player must press the start pushbutton. This begins the game play and the game time begins counting down from 100.
Now with the left hand on the steering wheel, the right hand on the four-speed gear shifter. the right foot on the accelerator foot pedal. and the sound of an idling motor, the player may begin to “drive” the car along the racetrack.
Acceleration is as in a real car. Start out in anything but first gear and the car accelerates slowly. Start out in first gear and the car accelerates nicely Once the car is moving, shifting into progressively higher gears increases the speed oi the car. If the car goes into a turn too rapidly, there will be the sound of the car skidding from the game cabinet speakers. if the car “drives” into a track boundary, a crash sound will be heard from the game cabinet speaker and the TV monitor viewing screen will flash.
The outstanding feature of Night Driver is that it is a game of skitl The player must skillfully manipulate his car along the track in a race against time.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Il. SPECIFICATIONS
2.1. GENERAL
Cabinet Dimensions: Height 73 inches, Width 2514 inches, Depth 32 inches.
Black and white 23-inch screen, video input. TV Monitor:
Coin Mechanisms: Two — identical mechanisms, accept only quarters.
Removable; located behind locked access door to coin mechanisms. Cash Box:
Power Cord: Approximately 6 feet long. extends from rear of game cabinet and has grounded three-prong plug for conventional grounded wall outlets.
Hidden above the Accelerator Foot Pedal for owner/operator access. On/Off Switch:
Located at the inside front of game cabinet to the immediate left of coin box. Self-Test Switch:
One 18-inch fluorescent tube for cabinet lighting. One 9-inch black light for bezel lighting. Lighting:
2.2 ELECTRICAL
Power Requirements:Uses conventional grounded wall outlet providing 110 volts AC, 60 Hz, single phase, rated at about 200 watts.
All fuses accessible from Rear Access Door of the game cabinet; TV monitor has two 3AG 1-amp slow blow, 250 volt fuses and remainder of game is protected by two 3AG 3-amp quick blow, 250 volt fuses, both Fusing: mounted side-by-side on the Electronics Tray Assembly.
Power Interrupt Switches: These are safety interlock switches located inside the game cabinet Rear Access Door. They cause the removal of AC power to the game when the access door is opened
2.3. ENVIRONMENTAL
Operating and From 32 degrees Fahrenheit to Storage 120 degrees Fahrenheit (am- Temperature Range: bient temperature}
Maximum of 80% without condensation. Relative Humidity:
2.4 OWNER/OPERATOR OPTIONS FOR STRUCTURING OF GAME PLAY
Cost: @ 25¢ per player 25¢ per two players © 50¢ per player
e 50 seconds © 75 seconds © 100 seconds © 125 seconds Game Length:
Extended Play See paragraph 3.4.2 in Section
2.5 ACCESSORIES AVAILABLE ON SEPARATE ORDER
Video Probe: Order from Atari
Computer Test Fixture: Order from Atari, catalog no. CTF-1
Order from Atari, Plugs and Test PROMs Computer Test Fixture Night Driver Adaptor: Program
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Ill. DESCRIPTION
3.1. FUNCTIONAL DESCRIPTION OF GAME The block diagram in Figure 3-1 illustrates the major functional parts of the Night Driver Game. Note that the game printed circuit board (hereafter referred to as PCB) sends composite video signal to the IV monitor and a separate audio signal to the game cabinet speaker
3.2. GENERAL INFORMATION General information about the game in the tollowing subparagraphs provides a background for the Installation Instructions in Section V of this manual, and the description of Game Sequence in paragraph 3.3 of this section,
3.2.1 Energizing the Game: The game is energized by inserting the AC power plug into an active wall outlet that provides the specified AC power as listed in Section 4M, Specifications. of this manual. The Power On/Off switch, hidden above the accelerator foot pedal must be set to the “on” position.
3.2.2. TV Monitor: The game's TV monitor is a self-contained transistorized television monitor with composite video input. Because the composite video signal sent to the monitor by the control circuitry differs in many respects from the signal derived from commercial TV broadcasts. the picture appearing on the screen is unlike that of ahome TV set and the monitor does not produce any sound.
3.2.3. TV Monitor Picture: The game's TV monitor picture produces only two levels of video (white and black), instead of more or less continuous shades of gray seen on a home TV screen.
3.3. GAME SEQUENCE
3.3.1 Operating Modes: During normal use, Night Driver can be described as operating in one of two modes—attract and play. Connecting the power cord to the proper AC source energizes the game and the game will be in the attract mode. The game remains in the attract mode until the proper number of coins have been inserted and the coins clear the coin mechanism and the start pushbutton has been pressed. Pressing the start pushbutton initiates game play and the game timer begins counting down from 100 by one-digit increments. When the timer reaches zero, the game goes into the attract mode (see Owner/Operator Options, paragraph 3.4 of this section).
3.3.2 Attract Mode: Figure 3-2 illustrates the TV monitor display during the attract mode. During the attract mode the
HIGH SCORE 000 TOP SPEED 000 GAME OVER ATARI YOUR SCORE 000 TOP SPEED 000
Figure 3-2 Attract Mode TV Monitor Display
TV monitor wil display the highest score and speed obtained by a player since the last power-up of the game. The words “GAME OVER" will flash on and off. The roadway pylons will move as if the car is moving along the road.
3.3.3 Play Mode: Figure 3-3 illustrates the TV monitor display during the play mode. During this mode the TV monitor will display a roadway that advances when the accelerator foot pedal is stepped on. Shifting the gear shifter through the gears increases the advancing speed of the roadway pylons. \f the car comes into contact with one of the pylons, the roadway pylons will stop advancing, the TV monitor display will flash, and a crash sound will come from the game speakers. If the car “drives” off the roadway, the following message will be displayed on the TV monitor:
Ac SOURCE a MORIZUNTAL DEFLECTION
Iw Moni TOR INTE RUC SWITCH
INTERLOCK SWITCH FLECTROMICS tRAy ASSEMHL Y CIRCUITRY
VERTICAL PLELEC TION
TY SHEET ASSEN Y
COIN MIE CHANISNN
COI MECHARISHE
Stan PUSH BUTTON
TRACK SULECT ROCKER SWITCH
STLLRING CONTROL
1 SPFFOGTAR SHIFTER
ACCELERATOR TOOT PEDAL
SFLF TEST swirce coMmens iT neo
AUDIO
Figure 3-1 Functional Block Diagram of Night Driver Game
TIME 089 TOP SPEED 103 YOUR SCORE 013
Figure 3-3 Play Mode TV Monitor Display
OFF THE ROAD WAIT FOR THE TOW TRUCK
After approximately three seconds, the message will disappear and the roadway pylons will reset so that the car is again between the roadway pylons.
Table 3-1 Price/Time Per Game Options Settings
SWITCH SECONDS PLAY POSITION PRICE
| 0 | 50 | 2 plays/coin |
| 1 | 50 | 1 play/coin |
| 2 | 50 | 1 play/coin |
| 3 | 50 | 1 play/2 coins |
| 4 | 75 | 2 plays/coin |
| 5 | 75 | 1 play/coin |
| 6 | 75 | 1 play/coin |
| 7 | 25: | 1 play/2 coins |
| & | 100 | 2 plays/coin |
| 9 | 100 | 1 play/coin |
| A | 100 | 1 play/coin |
| B | 100 | 1 play/2 coins |
| Cc | 125 | 2 plays/coin |
| D | 125 | 1 play/coin |
| E | 125 | 1 play/coin |
| F | 125 | 1 play/2 coins |
3.4 OWNER/OPERATOR OPTIONS
3.4.1 Price/Time Per Game Options: Mounted on the Night Driver PCB is a hexadecimal switch that has fifteen different: switch positions. This switch, located at coordinates 110 on the PCB (see Figure 3-4). may be adjusted for the desired price/time structuring as indicated in Table 3-
- The Switch Position column indicates the alphanumeric that is printed on the switch itself, as well as the first character immediately following the word OPTIONS in the TV monitor display during self-test (see Figure 5-1). The Seconds column indicates the total play length (not including bonus, as adjusted according to paragraph 3.3.2). The Play Price column indicates the Price to play the game. 3.4.2. Bonus/Track Difficulty Options: Mounted on the Night Driver PCBis a four toggle DIP(dual in-line package) switch, This switch (see Figure 3-4). located at coordinates M10 on the PCB, may be adjusted for no bonus time, bonus time, or “hard-to-get" bonus time. Also this switch may be adjusted to change the tracks, thus decreasing the ‘player familiarity” factor. Theseoptions are all listed in Table 3-2. The Switch Position column indicates the toggle position of switch M10 on the Night Driver PCB. The Self-Test Display column indicates the four characters grouped together after the word OPTIONS in the TV monitor display during self-test (see Figure 5-1). The Option column indicates the option provided when that switch is in the ON position.
3.4.3. Volume Control: Control for the volume of all game audio is located on the Night Driver PCB. This is a small potentiometer (R111) located on the component side of the PCB, as illustrated in Figure 3-4,
Table 3-2. Bonus Time/Track Familiarity Options Settings SELF-TEST DISPLAY SWITCH POSITION 1 2 °3 ~¢4 OFF OFF OFF OFF 0000 ON OFF OFF OFF 1000 OPTION
No option selected. Toggle 1 provides bonus time (equal to game time) awarded for score of 350. Toggle 4 ON when Toggle 1is ON makes bonus time score of 350 more difficult to achieve. Toggle 2 reverses the turns of all three tracks Toggle 3 has no function and is not connected in the circuit. ON OFF OFF ON — 1001
ION ON OFF ON — 1101
ON ON ON ON © 1111
“I
Bonus Time/ Track Familiarity Switch
Price/Time Switch
Figure 3-4 Locations of Owner/Operator Option Switches and Volume Control
IV. THEORY OF OPERATION
4.1 GENERAL COMMENTS This section provides a technical description of the Night Driver PCB that is supplemental to the signal description in Section VII, Troubleshooting. Section IX contains schematic diagrams, assembly drawings and parts lists referred to in the following subparagraphs of this section. Figure 4-1 is a block diagram of the Night Driver PCB.
On the Night Driver PCB schematic diagram, drawing number 006231, the symbol P (appearing at vatious inputs of the integrated circuits) indicates a connection to +5 VDC through one of the 1k ohm resistors R7, R48, R52, R112.
For easy reference, the Night Driver PCB is. divided into 126 sections. These sections are identified by letters A through R (skipping letters G, |, O,andQ, because they may easily be confused with numbers 6, 1, and 0) for the short side ot the PCB and numbers 1 through 9 for the long side of the PCB. For example, sheet 3. of schematic 006321 illustrates a randomaccess memory (RAM) H6 at the upper left of the drawing. The component hardware of RAM H6 will be found at coordinates H and 6 on the PCB.
4.2, COMPONENTS OF THE MICROCOM- PUTER SYSTEM The microcomputer system carries Out complex tasks of the game by performing a large number of simple tasks. Control of the system is the primary function of the Microprocessor, The Microprocessor causes the system to perform the desired operations by addressing the Program PROMs (programmable read-only memories} for an instruction, reading that instruction, then executing the simple task dictated by that instruction. Temporary storage of data necessary for the execution of a future instruction, such as arithmetic operation, takes place in the Page Zero memory.
4.2.1 Program PROMs (bottom of schematic sheet 3): The Program PROMs consist of read-only memories (ROMs), permanently programmed by Atari to execute the Night Driver game. This memory has the capability of outputting eight bits of data for each of 2,048 combinations of ones and zeros on the ten address inputs. In computer terminology, this is stated as a memory size of 2K x 8.
The Night Driver game contains one of two combinations of ROM chips to make up the Program PROMs, depending on when the individual Night Driver PCB was manufactured. For the early production models, Program PROMs consist of eight chips (as illustrated to the left of the word PROGRAM PROMS on the schematic diagram). Later production models consist of two chips (as illustrated to the right of the word PROGRAM PROMS on the schematic diagram). The eight Program PROM chips are completely interchangeable with the two Program PROM chips, but need not be retrofit
Since data in the Program PROMS is a permanent physical configuration of the PROM chips, the data is not lost when power is disconnected from the game or when the chip is removed from its socket. Since the Program PROMs consist of read-only memories, the result of an address input can only be the “reading” of data stored in the manufacturing process. It is not possible to “write” in more data. (The term PROM stands for programmable read-only memory. To Atari, this means that the chip is a programmable ROM. To you, this chip is oniv a ROM.)
4.2.2 Page Zero Memory (right side of schematic sheet 3): Page Zero memory consists of two random-access memories (RAMs). Data may be stored in Page Zero memory (called ‘writing’ Page Zero), then later recalled (called “reading’’ Page Zero). Memory size of Page Zero is 512 x 8
In order to read Page Zero, R/W (pins 16) input of the chips must be a high logic level and OD (pins 9) input must be a low logic level. To write Page Zero, R/W input must be a low logic level and OD input must be a high logic level.
As previously mentioned, data stored in Page Zero memory is for the purpose of performing operations on data as instructed by the Program
Re epar
ADDRESS _| ADDRESS ENABLE
DATA yea
PROGRAM PROMS nam BOOP
ADOAESS DATA » PLavEieto
DATA
ENABLE
ABD ACESS
STEERING
ACCELERATOR ENABLE ouTPuT PORTS
MOTOR SOUND
Figure 4-1 Block Diagram of the Night Driver PCB
PROMs. Since Page Zero is a temporary storage area, removing power from the chips will “erase” all stored data.
4.2.3 2): As mentioned earlier, the controller of the Microcomputer is the Microprocessor. From the Microprocessor, a sixteen-bit address bus addresses the Program PROMs, Page Zero, and Enable. An eight-bit bi-directional data bus serves as a path for wansferring data from the Program PROMs, to and from Page Zero, and to the Roadway RAMs. Microprocessor (left top of schematic sheet
4.2.4 Tri-State Devices: Tri-state devices, such as M1 of schematic sheet 2, are capable of having normal logic output of ones and zeros when disable (pin 1) is ata low logic level. When disable is at a high logic level, the output becomes a high impedence. In other words, when disable is at a high logic level, it is equivalent to completely removing device M8 from the circuit. ROMs and RAMs are also tri-state devices. Each ROM or RAM must be enabled by a certain logic level at its chipenable input before the device is capable of inputting or outputting data. In the case of the Page Zero RAMs, this chip-enable input is identified as OD.
4.3, MICROCOMPUTER SYSTEM The primary function of the Night Driver Microcomputer is to instruct the game circuitry for the proper TV monitor display and audio outputs for corresponding manual inputs. 4.3.1 Program PROMs Enable: With initial power applied to the Night Driver PCB, the Microprocessor addresses the Program PROMs for an instruction by placing a sixteen-bit code at outputs ABO through AB15. Enable H2 receives three address lines (AB10, AB11, and AB12) as an instruction of which part of the Program PROMs to access. Outputs of one-of-ten decoder H6 enable
only the individual ROMs of the Program PROMs required for the desired instruction
4.3.2 Page Zero Enable: Now. with Liable addressed for the enabling of the desired Programy PROMs, and the Program PROMs addressed for a data instruction, the Microprocessor receives an eight-bit data instruction from the Program PROMs on the data bus. If this data instruction includes the storage of information, the Microprocessor addresses Enable one-of-ten decoder }2 taddress lines BAY, BAT0, and BA11) to enable Page Zore, and it writes data into Page Zero, The procedure of writing into Page Zero is enabled by two signals: output disable OD {pin 9) must be a high logic level and read awrite R/W {pin 16} must be alow logic level With this condition, data from the Microprocessor an. the data bus is stored into a Page Zero location determined by Page Zero address inputs BAO through BAT.
p2 E4 pin6 |. 4 usec fe 0.46 usec | 72 E4 pin 8
Figure 4-2. b2 and 2 Signals 4.3.3 Phase 2: Phase 2(B0 2) is an output of the Microprocessor and is derived from the IMHz input signal from divide-by-twelve M3, Phase 2 is the master timing signal of the microcomputer system. The signal, as illustrated in) Figure 4-2, is positive when the Microprocessor addresses the Program PROMS for a data instruction
The Microprocessor addresses Page Zero and writes or reads data when the inversion of phase 2, or phase 2 not (Be)2), is positive
4.3.4 Playfield and Roadway Address: Both the Playtield and Roadway are addressed by the tour least significant bits of the address bus from the Microprocessor. However. in order to write data into the Playfield or Roadway RAMs, the latter must receive their enabling signals from Enable J2. Since phase 2 is not an input to Enable J2 (actually C4 pin 5}: data is only written into the Playfield and Roadway RAMs when phase 2 not is a low logic level
4.4. MICROCOMPUTER WATCHDOG Watchdog is an external monitoring system that resets the Program execution back to its initial instructions, if the program execution deviates from its intended sequence. This is accomplished by a watchdog statement (address code), incorporated in Program Memory (Program PROMS), that results ina WATCH-DOG pulse at the clear inputs of flip-flops L7 This clears the count of vertical blanking pulses (V BLANK) and must be accomplished before the flipflops reach the count of three vertical blanking pulses
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
V. INSTALLATION INSTRUCTIONS
5.1 UNPACKING INSTRUCTIONS
5.1.1 Examination for Shipping Damage: Before shipment from the factory, components and sub-assemblies of each game are carefully checked for proper operation. However, during shipment some adjustments may have changed or parts may have been damaged. Upon initial removal of the game from the shipping container, first examine the exterior of the cabinet, Then open the reat access panel (refer to Section VIL, Disassembly and Assembly) and examine the interior of the cabinet. Any shipping damage, such as a dented, cracked or broken cabinet, sub-assemblies broken loose, ete., should be reported immediately to the shipper and to Atari, Inc
5.1.2. Mechanical Inspection: After determination that the game has been received in good condition, carefully inspect the interior parts and verily the following:
- All plug-in connectors are firmly seated.
(b} The fuses are all seated in their holders.
ic) No loose foreign objects are present (especially metal objects that could cause electrical short circuits)
id) No harness wires have become disconnected or pulled loose.
Be sure all major assemblies have been checked: game PCB, the transformer and other components on the electronics tray assembly. the two coin mechanisms, the speakers. player controis. and TV monitor chassis
Do not go on to the remaining paragraphs in this section until the above mechanical inspection has been thoroughly performed.
5.2. VERIFYING OPERATION OF INTERLOCK SWITCHES: Interlock switches are located inside the rear access door and are there to prevent accidental shock of anyone who has reason to stick a hand inside the game cabinet. The function of these switches is to remove all power that goes into the game when the rear access door is open. These switches are mechanically aligned by Atari, but it is important that they are checked to insure the proper operation after shipping
Afier the completion of subparagraph 5.1.2, plug the AC Power Cord into the appropriate AC Power Source (refer to Section il, Specifications). Set the “Power On/Off” switch, hidden above the accelerator foot pedal. to the “on” position. Within approximately thirty seconds, there should be a raster display on the TY monitor. Verify operation of interlock switches as follows:
(a} Unlock and completely remove rear access door. This will cause the picture of the TV monitor screen to disappear
- Press switch plunger for one of the interlock switches and hold for at least ten seconds. If TV monitor picture comes on, replace the other interlock switch
(c Repeat step (b) with the other interlock switch.
- Check that both interlock switches are aligned in a manner that when the rear acecess door is opened. the interlock switches will disengage.
Do not go on to the remaining subparagraphs in this section until the operation of the interlock switches has satisfactorily verified.
5.3. OPERATION OF SELF-TEST FEATURE
5.3.1 Activating the Self-Test Feature: Bejore activating the Self-Test feature, set the track select switch to the PRO TRACK position andset the gear shifter to the 4th gear position. Now activate the Self-Test feature by unlocking and opening the coin mechanism door, then setting the Self-Test switch located immediately inside and to the leit of the coin mechanism door to the “on” position.
ABCDEFGHIJKLMNOPQRSTUVWXYZ 0123456789 OPTIONS F 1111 ROM OK
Figure 5-1 Self-Test TV Monitor Display
5.3.2. Visual Check: The TV monitor viewing screen’s display shall be as illustrated in Figure 5-1. The major items of the display to be checked are as follows:
- Alphanumerics: Check to make sure that all alphanumerics are displayed in the correct order and each character is complete. Any problems that exist indicate a problem associated with the playfield generator. To troubleshoot, refer to paragraph 5.4 in this section.
- Options: At this time, ignore the OPTION line of the TV monitor display. This will be discussed in subparagraph 5.3.4.
- ROM Check: The ROM line should indicate a statement “ROM Ok”. If not the statement will indicate ROM 1 through 7. This number represents the ROM or combination of ROMs that have failed this test. To troubleshoot, refer to paragraph 5.4 in this section.
- Roadway Check: The bottom of the TV monitor viewing screen shall display two sets of white boxes that diminish in size from the bottom up and have seven boxes in each group. If these boxes are in any way different than as illustrated in Figure 5-1, refer to paragraph 5.4 in this section
(ec) Steering Check: Turn the steering wheel to the right. The roadway pylon boxes should move to the right. Turn the steering wheel to the left. The roadway pylon boxes should move to the left.
- Start Light) Check: The start pushbutton should be lighted. If not, refer to paragraph 5.4 in this section.
5.3.3 Audio Check: Perform the following check steps. If there is a failure, refer to paragraph 5.4 in this section. The following checks should cause an audio screech sound from the game speakers:
- Set track select switch to NOVICE TRACK position
- Set track select switch to EXPERT TRACK position.
(c} Press the start pushbutton.
- Set gear shifter to Ist-gear position.
- Set gear shifter to 2nd-gear position
- Set gear shifter to 3rd-gear position
- Step on the accelerator foot pedal.
- Trip the right coin acceptor.
- Trip the left coin acceptor.
The following checks should cause mo audio screech sound from the game speakers:
- Set track select switch to PRO TRACK position.
- Set gear shifter to 4th-gear position.
5.3.4 Adjusting the Options: The option line of the TV monitor display indicates the optional game structuring for which the game has been set. These options are adjustable by the owner/operator. For instructions for setting these options. refer to paragraph 3.4 of Section III, Description of Operation
5.3.5 Game Play Operation Test: Set the Seli-Test switch to the “ofi” position. Check the operation of the coin mechanisms by inserting old and new coins into the coin slot. Once you determine that the coin mechanisms are OK, initiate game play by pressing the start button. Check that the car motor sound increases while shifting through the gears with the accelerator foot pedal depressed. Then check that there is acrash sound and that the TV monitor display flashes when a roadway pylon makes contact with the car. The game is now ready to earn money.
5.4 TROUBLESHOOTING SELF-TEST FAILURES 5.4.1 Visual Check Failures: The following subparagraphs (a) through (f) refer to the identical subparagraphs (a) through (f) of paragraph 5.3.2. Visual Check. For example, if there is a failure in the alphanumerics line on the TV monitor display as described in step (a) of subparagraph 5.3.2, troubleshoot by following the hints and instructions in step (a) of this subparagraph. !f there is no TV monitor display, check to make sure that the game is plugged into an active AC source, the game is turned on (hidden ON/OFF switch}, check all connectors, check all fuses, and check interlock switches. If these are all OK, troubleshoot TV monitor (substitution is best way), then troubleshoot Night Driver PCB (substitution is best way).
- Alphanumerics: Replace Night Driver PCB (refer to Section VII), If all of the TV monitor display is garbled, this indicates a problem withthe data and/or address lines in the Night Driver PCB. Check that lines are not shorted together or to ground. If TV display is garbled except for boxes at the bottom of the display, there is a malfunction in the Playfield signals. Check these signals using Table 8-1 in Section VIII of this manual as a guide for Circuit familiarization and troubleshooting. Suspect input/output signals of RAM M2 or ROM P2. Ii alphanumerics line is completely missing, suspect NAND gate }5 or shift register P3 input/output signals.
- This step was skipped.
(¢) ROM Chock: Replace Night Driver PCB (refer to Section VII). If ROM line of the TV monitor display indicates a number instead of OK, then refer to Table 5-1. Find the number that matches the number
Table 5-1 ROM Failures
FAILURE NUMBER FAILING ROM(s)
D1, J1 E1, K1 D1, £1, J1, K1 71,01 D4, F1, J1, 11 E1, F1,J1, 11 C1, D1, £1, FI H1, 1, K1, 01 NODURWNA
displayed after the word ROM on the TV monitor display in the FAILURE NUMBER column of Table 5-1. Match that number with the FAILING ROM(s) column. Troubleshoot the ROM circuit(s) indicated in Yable 5-1 using Table 8-1 of Section VII! of this manual as a guide for troubleshooting.
(dj) Roadway Check; Replace Night Driver PCB (Refer to Section VI). If the Roadway display is missing or garbled, there is a malfunction in the Roadway circuits. Check these signals using Table 8-1 of Section VILL of this manual as a guide for circuit familiarization and troubleshooting. If Roadway display is missing, suspect shift register M5 input/output signals, vertical line comparator E7, F7, N7, P7 (pin 8 output), and P8 (pin 6 output), or match latch N3. if garbled, suspect
Roadway RAMs E6, H4, H6, J4, J6, K4, L4, L6, M6, and P6.
- Steering Check: If Roadway pylon boxes move in one direction but do not move in the other direction, replace Night Driver PCB. There is a malfunction in the Input Port circuits. Check these signals using Table 8-1 of Section VIII of this manual as a guide for circuit familiarization and troubleshooting. Suspect flip-flop £8 (pin 9 output), multiplexer K9 inputs and outputs, or tri-state device M8 inputs and outputs. If Roadway pylons do not move atall, check continuity of harness wires between Steering PCB and Night Driver PCB. If continuity is OK, check for a voltage that switches between +2VDC and +5 VDC on pins 4 and 8 of the Steering PCB (referenced to ground) as the steering wheel is very slowly turned. If this voltage is as specified, replace the Night Driver PCB. Suspect flip-flop E8 inputs and outputs, multiplexer K9 inputs and outputs, or tri-state M8. If voltage is not as specified, replace Steering PCB.
- Start Light: Ifstart light is not lighted, check for +5 VDC on red wire to Start Switch. If voltage is not present, check continuity of harness wire between switch and Night Driver PCB. If continuity is OK, short black/red wire to Start Switch to ground through a 150-ohm resistor. If still unlighted, replace switch, If lighted, replace Night Driver PCB. Suspect Output Port £5 inputs and outputs or Schmitt trigger J8 (pin 10) output.
5.4.2 Audio Check Failures: The following subparagraphs (a) through (k) refer to identical subparagraphs (a) through (k) of subparagraph 5.3.3, Audio Check. For example, if there is a failure in step (a) of subparagraph 5.3.3, troubleshoot by following the hints and instructions in step (a) of this subparagraph. If there is no audio sound present in any of the steps in subparagraph 5.3.3, check continuity of white/black wire from gear shifter switches to ground. If continuity is OK, check operation of speakers by substitution. If speakers are OK, replace Night Driver PCB. Suspect Input Port F9 inputs and outputs or tri-state MB.
- If nosound, check voltage on red/white wire to the track select switch. If voltage is +5 VDC, replace track select switch. If voltage is 0 VDC, replace Night Driver PCB. Suspect Input Port F9 input.
- If no sound, check voltage on white/red wire to the track select switch. If voltage is +5 VDC, replace track select switch. If voltage isOVDC, (d)
le
'g
{h
i
iT)
(k ) replace Night Driver PCB. Suspect Input Port F9 input.
There should be no audio.
{f no sound, check voltage on gray wire to the Start pushbutton, If voltage is +5 VDC, replace Start pushbutton. If voltage is 0 VDC, replace Night Driver PCB. Suspect Input Port F9 input.
If no sound, check voltage on blue/white wire to first gear switch. If voltage is +5 VDC, replace switch. If voltage is 0 VDC, replace Night Driver PCB. Suspect Input Port F9 input.
If no sound, check voltage on yellow/white wire to 2nd-gear switch. If voltage is +5 VDC, replace switch. If voltage is 0 VDC and continuity between switch and Night Driver PCB is OK, replace Night Driver PCB. Suspect Input Port £9.
If no sound, check voltage on orange/white wire to 3rd-gear switch. If voltage is +5 VDC, replace switch. If voltage is 0 VDC and continuity between switch and Night Driver PCB is OK, replace Night Driver PCB. Suspect Input Port F9.
There should be no audio.
If no sound, check voltage on blue wire to accelerator foot pedal. If voltage is +5 VDC, replace switch. If voltage is 0 VDC and continuity between switch and Night Driver PCB is OK, replace Night Driver PCB. Suspect Input Port F9.
If no sound, check voltage on orange wire to coin acceptor switch. If voltage is +5 VDC, replace switch. If voltage is 0 VDC and continuity between switch and Night Driver PCB is OK, replace Night Driver PCB. Suspect Input Port Schmitt trigger E9 (pin 12) output or input of multiplexer F9.
If no sound, check voltage on yellow wire to coin selector switch. If voltage is +5 VDC, replace switch. If voltage is 0 VDC and continuity between switch and Night Driver PCB 15 OK, replace Night Driver PCB. Suspect Input Port Schmitt trigger E9 (pin 2) output or input of multiplexer F9.
Vi.
6.1 ROUTINE MAINTENANCE Due to its solid-state electronic circuitry, this Atari game should require very little maintenance and only occasional adjustment.
Game cabinets and glass may be cleaned with any non-abrasive household cleaner. If desired, special coin machine cleaners which leave no residue can be obtained from distributors.
6.2 ADJUSTMENTS ON TV MONITOR The TV monitor need be adjusted only when the picture is distorted, or if the contrast or brightness seem out of adjustment
MAINTENANCE AND ADJUSTMENTS
The TV monitor is accessible only from inside the game cabinet and these adjustments have to be done while the game is energized. Therefore only persons familiar with safety measures and repair procedures on electrical equipment should perform them.
The monitor's adjustments function like those of a conventional commercial television set, except that the volume adjustment has no effect. Instead the yame produces its sound in a speaker separate from the TV monitor. Figure 6-1 shows the location of the adjustments on the rear of the chassis. When making the adjustments follow these general guidelines:
FUSES CONT © BRITE VERT HORIZ VOL HOLD HOLD
Figure.6-1 Location of Adjustments on TV Chassis
BRITE (Brightness)—Perform this adjustment betore the contrast. Adjust so that the white lines covering the screen just barely disappear. when the brightness is turned up. CONT (Contrasti—Adiust so that the images are as bright as possible against the — dark background without being blurred. HORIZ HOLD (Horizontal Hold)—Adjust if the picture is slightly off-center horizontally, if the images appear warped, or if the picture is broken up into a series of diagonal lines. Adjust for a stable, centered picture VERT HOLD (Vertical Hold)—This needs adjustment only if the picture appears to be rolling up or down the screen, Adjust for astable, centered picture.
Vil.
7.1 GENERAL INFORMATION The following procedures are supplemented by exploded diagrams 7-1 for the front of the game cabinet and 7-2 for the rear of the game cabinet. All capitalized component terms directly refer to the parts list and drawing A006264-01 located in Section IX of this manual.
When working inside the Rear Door Assembly, always check to make sure that the two interlock switches are not in the defeat position or stuck in the “on” position.
7.2. REMOVING AND INSTALLING THE NIGHT DRIVER PCB
- Remove three #8x14%-inch Flat Head Phillips Screws from each side of the Rear Door Assembly.
- Unlock and remove Rear Door Assembly.
- Locate R.F. Shield Box Assembly immediately inside the rear access and mounted on the right side panel. it is an aluminum box with many small holes. On the closest end of the box is the R.F. Board Assembly.
- Unplug the edge connector from the R.F. Board Assembly.
- Remove five #6x¥2-inch Small Pan Head Phillips Screws from each of the long sides (total of ten) of the R.F. Board Assembly.
- Carefully remove the R.F. Board Assembly while pulling the Night Driver PCB out of the R.F. Box Assembly.
To install the Night Driver PCB, follow preceding steps (a) through (f) in the reverse order. Do not force or bend the printed circuit boards. Before installing them into the R.F. Shield Box Assembly, always inspect the two printed circuit boards for physical damage. &
DISASSEMBLY AND ASSEMBLY
7.3_ REMOVING AND INSTALLING THE TV MONITOR
- Remove three #8x1¥%4-inch Flat Head Phillips Screws from each side of the Rear Door Assembly.
- Unlock and remove Rear Door Assembly.
- Unplug the 12-pin Molex connector from the chassis of the TV monitor.
({d) With a 34-inch wrench, remove two #10-24 Machine Hexagonal Nuts, two #10 Split-Lock Washers, and two #10 Flat Washers from underneath the bottom rear sides of the wood TV Shelf Assembly.
- Remove two #10-24x1.25-inch Carriage Bolts from the top reat of the wood TV Shelf Assembly.
- With a ¥%-inch wrench, remove four “4-20 Machine Hexagonal Nuts, four ¥%-inch Split Lock Washers, and four ¥%4-inch flat washers from the rearmost outer edges of the Dashboard Assembly.
- From the front of the game cabinet, being careful not to pull on the harness wires, lift the the Dashboard Assembly away from the game cabinet.
{h) Push upwards and pull out the Main Display Plexiglas.
{i) Remove the 23” Monitor Bezel.
- Slowly and carefully, slide the TV Shelf Assembly forward and out of the game cabinet.
- To install the TV Shelf Assembly, follow preceding steps (a) through {j) in the reverse order. If installing a new TV Shelf Assembly, remove the race car from the screen of the old TV monitor. Attach the race car to the center of the TV monitor screen with the bottom of
17 LIGHT BOX PANEL PLEXIGLAS
FLUORESCENT TUBE
BLACK LIGHT
16 23’ MONITOR BEZEL
16A MAIN DISPLAY PLEXIGLAS.
2 DASH BOARD ASSEMBLY
Figure 7-1 Exploded View, Front of Game Cabinet
7 R.F. SHIELD BOX ASSEMBLY
9 PC BOARD
8 R.F. BOARD
11 REAR DOOR ASSEMBLY ™al 4 ELECTRONIC TRAY ASSEMBLY ZA.
Figure 7-2 Exploded View, Rear of Game Cabinet
the race car '>-inch above the bottom of the screen. Use a water-soluble glue or adhesive tape.
7.4 REPLACING THE STEERING BOARD PCB fa) Remove three #8x114-inch Flat Head Phillips Screws from each side of the Rear Door Assembly
- Unfock and remove Rear Door Assembly
Unplug the 10-pin Molex connector from the Steering Board PCB. (c
With a7/16-inch wrench, remove self-locking hexagonal nut and %-inch internal tooth starlock washer from the steering wheel axis screw, while a helper holds the steering wheel at the front of the game cabinet. (d
- Remove black plastic edge-toothed wheel.
- Remove Steering Board PCB by removing two #2-56x12-inch Pan Head Phillips Screws.
- To install the Steering Board PCB, follow preceding steps (a) through (f) in the reverse order. Before installing the Steering Board PCB, make sure there is a sufficient amount of silicone lubricant on the inner hole of the black plastic edge-toothed wheel.
7.5 REPLACING FLUORESCENT TUBE {a) With a %-inch hex wrench, remove three #10- 32x1-inch Button Head Socket Cap Screws from the top Plexiglas Retainer. ib) Lift the Attraction Panel Plexiglas up and out of the bottom Plexiglas Retainer.
ic} Remove fluorescent tube.
- To instail Attraction Panel Plexiglas. follow preceding steps (a} and (bi in the reverse order,
7.6 REPLACING BLACK LIGHT TUBE
- Remove three #8x1'4-inch Flat Head Phillips Screws from each side of the Rear Door Assembly
- Unlock and remove Rear Door Assembly.
- With a ‘s-inch wrench, remove four !4-inch tlat washers from the back-side outer edges of the Dashboard Assembly.
- From the front of the game cabinet, being careful notto pull on the harness wires, lift the Dashboard Assembly away from the game cabinet
(ce) Push upwards and pull out the Main Display Plexiglas
(f} Remove the 23” Monitor Bezel.
- Remove black light.
- To reassemble the game cabinet, follow preceding steps (a) through (g) in the reverse order.
Vill.
8.1 GENERAL PROCEDURE
This section describes troubleshooting procedures in detail sufficient for a person with moderate technical ability to understand. However, for those interested in gaining more information on video game technology, especially the electronics, we recommend reading the Video Game Operator’s Handbook, manua! no. TM- 043. This book is available from Atari, Inc., attn. Customer Service Dept., 2175 Martin Avenue, Santa Clara, CA 95050 for $5.00 each, or from your distributor.
8.1.1 Identifying the Trouble Area: If the Night Driver game fails to respond properly to any of the tests as described in paragraph 5.3 of Section V, Installation Instructions, troubleshoot the game as described in paragraph 5.4. When a failure occurs, you should make certain the failure doesn’t exist due to skipping or misreading one of the procedural steps. For failures of the audio checks in subparagraph 5.3.3, it is common sense to first check the associated harness wires using the harness schematic in Section IX of this manual.
The statement “Replace the Night Driver PCB” is intended to eliminate unqualified personnel from damaging this expensive item. The Night Driver PCB is a complicated non-throw-away item and should be only worked on by those who are familiar with its circuitry.
Table 8-1 and Insert 8-1 are a comprehensive familiarity guide to the Night Driver PCB signals. Figure 8-1 is an illustration of the steering signals. All signals of the Night Driver PCB are described in Table 8-1, and many of the signals are illustrated in the figure and insert. For signals to the Playfield and Roadway circuits, the table was written in the same order that the actual hardware receives the signals. The table first covers signals of schematic sheet 1 of the Night Driver PCB; the second sheet, then the third sheet.
TROUBLESHOOTING AND REPAIR
8.1.2 Locating the Trouble Cause: Once a problem has been narrowed down to one or more areas, the next step is to perform various tests and measurements to isolate a specific cause of the trouble. Remember that sometimes a very complicated problem, such as erratic game operation, can be traced to a simple cause—the printed circuit board not being properly seated in its edge connector. Start with the most suspect area and trace backwards from the point where the trouble is first observable, using a process of elimination to eventually locate the faulty component, connection, etc.
Substitution of parts is.a legitimate and easy way to isolate the cause. For instance, if the PCB is the suspected trouble area, remove it and substitute a known-to-be-good PCB. Then check for correct game operation. Similarly, to check the TV monitor, connect the game to a known-to-be-good monitor. The harness can often be checked by substitution also. Substitute both a known-to-be-good PCB and TV monitor. If the trouble still persists, the harness must be at fault.
The test equipment for use in troubleshooting is discussed in paragraph 8.2. 8.1.3 Correcting the Trouble Cause: In practice, the steps required to correct troubles can range from simple adjustments (correctly seating the PCB in its edge connector, changing the setting on a potentiomeier, adjusting the picture controls on the TV monitor) to repair of loose connections and replacement of defective parts, Extreme care should be exercised when removing integrated circuit devices and discrete components. Use a 40-watt maximum soldering pencil with a small tip designed especially for IC work, Before removing an IC, clip the signal output or input lead of the suspected failing IC to determine if another component is creating the problem. To remove an IC device, follow this procedure:
Clip all leads and lift the IC package out, leaving two rows of leads. Then remove leads individually with a soldering iron and needle-nose pliers. Finally, evacuate the holes with a solder sucker. Afterwards
STEER 7 a a ping RIGHT TURN STEER 1B i ee EQ pin 11
STEER 1A | | i | | L E9 pin 9 LEFT TURN steent8 | CftCt«idLS(“(FTSC*dC Ss Spin
low logic level STEERA RIGHT TURN STEERB J K9 pin3 K9 pin 13
STEERA
LEFT TURN high logic level K9 pin 13
I steerB If LE IffsU U OU UO OU kenins
Figure 8-1 Steering Signals
clean the area thoroughly, using an approved PCB cleaning solution to remove any traces of flux and dirt. Alcohol will do in a pinch, if necessary.
The microprocessor, read-only memories, and tandom-access memories are removed by simply pulling them out of their sockets. When placing them into their sockets, make certain they are placed in the correct socket.
Insert the new IC device using an IC insertion tool, making sure that the reference notch is oriented correctly and that the device’s leads are not bent during insertion into the board. Afterwards, be sure to solder each lead on both sides of the PCB, using as little solder as possible. After soldering, clean the area thoroughly to remove the flux.
Observe the same removal and_ insertion procedures when replacing discrete components. Trim the leads as close as possible and be sure to orient diodes and capacitors correctly. 8.1.4 Verifying Correct Game Operation: After locating and correcting the cause of a trouble, re-energize the game and perform a final check by placing the game in the self-test function, then check for correct operation during game play. Doing this will verify that your troubleshooting was correct. If the game operation is still not correct, go back and double-check your work. Make sure that any replaced components were installed correctly. If this was done properly, then start the troubleshooting steps over again. Keep in mind that there may be more than one trouble at a time, and that correcting one trouble can sometimes bring previously undetectable troubles to light.
This verification is especially important when the original trouble has been intermittent, that is, was not happening all the time.
8.2 TEST EQUIPMENT Electronic troubleshooting of a video game essentially consists of checking for the presence of various signals and of examining their condition. A
signal can be thought of as acting like a “messenger” that carries instructions from one unit or circuit to another. Many different types of signals are produced in a video game, and for this reason several unusual and perhaps unfamiliar types of test instruments are used during troubleshooting. Each instrument has its own set of advantages and disadvantages for examining a given type of signal, and both the depth of the intended troubleshooting capability and budget will determine what instruments will be needed. Some instruments are basic and essential, no matter what size of service facility, while other optional instruments are desirable because they make troubleshooting easier and quicker. 8.2.1 Basic Test Equipment:
- The Video Probe, This is a simple but invaluable instrument having two leads—a test-clip lead and a test-probe lead. During troubleshooting of video signals the test-clip lead is left connected to the test point from resistor R65, located at coordinates P9 of the Night Driver PCB. When the test-probe lead is then connected to any video developmental signal, that signal will be coupled to the video signal going to the TV monitor and a video probe picture will appear on the TV screen. The shape and other characteristics ot this picture will give information about the signal being probed. the video probe is suited for troubleshooting synchronization and image signals, but willnotbe useful tor extremely fast signals fsuch as the Clock) or for very slow analog or digital signals.
A video probe can be constructed in a few minutes from these common electrical Components: a fength of 20 AWG (American Wire Gauge) rubbercoated wire, a 4.7K-ohm, '-watt carbon resistor, and two test leads. For the leads, use a single Mouser test clip (Mouser #131C301 or 302) attached to one end of the wire. and a test prod containing the resistor on the other.
To assemble the video probe, proceed as follows: Remove the cap trom the test clip and strip 3/16 inch off cach end of the wire. Solder one end to the postin the tesi clip. thread the other end through the hole in the cap. and snap on the cap. Next unscrew the plastic body of the test prod from the point and trim both leads of the resistor to a 3/16-inch length. Solder one resistor lead to the inside of the point. Thread the other end of the wire through the hole in the body and solder it to the other resistor lead; screw the body back onto the point
- The togic Probe. This is a test instrument designed tor fast verification of digital IC outputs, It is small, convenient to carry, easy to read, and relatively inexpensive, The logic probe derives its power from the system under test; it Ras two power leads, one for connection to ground and the other to +5 volts DC. When the logic probe's tip is held against a digital signal point, three colored lamps in the tip will indicate the signal's condition or state, as follows:
@ The red lamp lit indicates a high or logic level 1 (for TTL components, this is +2.4 to +5 volts) @ The white lamp lit indicates a low or logic 0 (for TTL components, this is 0 to +0.8 volt) ® the blue lamp lit indicates that the signal is changing states ® No lamps lit indicate the grey region between Oand 1 (lor TTL this is between +0.8 and #2.4 volts}
A circuit Shorted to ground will illuminate the white lamp end an open circuit will illuminate the red lamp
The Jogic probe is readily available trom electonic supply sources: a commercial model found satisfactory is the Kurz-Kasch model LP 520.
- The Logic Pulser. This test instrument is similar in size and shape to the logic probe. and it also derives. its power from the system under test. When the logic pulser’s tip is held against a digital signal point, the
source and sink capabilities of the pulser override any
{C output. and the pointis driven to the opposite logic level. If the point that the logic pulser is held against is low. pressing the switch on the side of the pulser will introduce a high pulse. Conversely, pulsing a high linc will pull that line low momentarily.
During troubleshooting the logic pulser allows stimulation of in-circuit ICs with a shaped digital pulse. For example, a certain feature of the game may not be working and you suspect that a circuit is not receiving the necessary signal. Use- the pulser to imitate that signal: if the circuit begins working, you have proved that the signal was in fact missing and you can begin tracking it down. This technique is very similar to jumping coils in electromechanical games such as pinball machines.
In addition to the regular “pulse” button, there is another switch mounted on the logic pulser. When this switch is set in the “rep” mode, the instrument pulses the digital signal point at a 5-Hz rate or 5 times per second. This extremely low rate is slow enough to allow watching events initiated by the pulser. Counter outputs, for example, are more easily observed when the counter is pulsed or clocked at this rate.
The logic pulser is also readily available from electronic supply sources; acommercial model found satisfactory is the Kurz-Kasch model HL 583.
- Oscilloscope. The most versatile test instrument, and also the most expensive, is the oscilloscope. The high-speed TTL integrated circuits usedin video games produce fast-rise-time signals. The oscilloscope should have a 50-MHz bandwidth, dual trace and dual time base capability. These latter features allow examination of both input and output signals simultaneously, so that precise timing relationships can be checked. The oscilloscope should also have provision for internal or external sync.
Of the newer, solid-state oscilloscopes, a satisfactory model is the Tektronix 465.
- VOM or Volt-Ohmmeter. This common measuring instrument is extremely useful in video game troubleshooting. It can be used to check tine voltage, transformer secondary windings, continuity, resistance, power supply voltages, and to some extent used for measurements in the analog circuitry.
One commercial model found satisfactory is the Simpson 260.
8.2.2 Optional Test Equipment:
- The Logic Comparator. This test instrument’s main benefit is that it can be used to check the functioning of an integrated circuit device while the device is still in place on the printed circuit board. The logic comparator performs the check by comparing the suspect ICs functioning with that of an identicaltype reference IC mounted in the instrument itself. Suppose that the functioning of a type-74195 device on the PCB is suspected to be defective. First insert a program card with a known-to-be-good 74195 into the logic comparator, and then clip the comparator test leads onto the leads of the suspect device. If there are any logic state differences between the reference IC and the suspect IC under test, then a LED on the logic comparator will light up to indicate which output is not functioning correctly. Once a defective IC has been located, it should be replaced.
Logic comparators are readily available from electronic supply sources.
- Atari Universal Test Fixture. In situations where a large number of video games are being serviced, investment in the Universal Test Fixture will be justified. This item of test equipment forms a test station for troubleshooting printed circuit boards after they have been removed from the game cabinet. The Universal Test Fixture has a full set of controls for operating the game and also has its own TV monitor. The game's PCB is plugged into an edge connector mounted on the side of the Fixture; with this arrangement the PCB is positioned in a convenient way for connecting probes and other test instruments.
A program and card inserted into a receptacle in the top of Fixture takes the place of the game's interconnect wires. The program card thus sets up the Fixture for each particular game; the game’s name is clearly printed on the program card itself.
With the Universal Test Fixture the method of troubleshooting via substitution of known-to-begood parts is made fast and convenient. For example, suppose that the TV picture in a game is completely broken up and you want to determine whether the game or monitor is causing the problem. Remove the PCB and plug it into the Fixture’s edge connector, and also insert the correct program card for that game. If the picture on the Fixture’s monitor is correct, then you know that the problem lies in the game’s monitor.
8.3. SPECIFIC TROUBLESHOOTING INFORMATION The following subparagraphs give additional troubleshooting information about certain areas of the Night Driver game.
8.3.1 Coin Mechanism: If a player inserts a com and the game does not respond, first check the coin mechanism. If pressing the coin rejector button forces the — rejector mechanism to return the coin, then examine the coin to make sure that it is genuine. If it is, then use a set of your own test coins (which should include both very new and very old, worn coins) to determine whether or not the player’s coin is undersize or underweight. If your test coins are also returned, this indicates that servicing of the coin acceptor portion of the coin mechanism is called for. Generally the cause of this particular problem is an improperly adjusted magnet gate.
Inside the coin mechanism a magnet is used to test the metallic composition of the coin. Highly magnetic coins, such as those made of steel or iron, will be retained by the magnet and can be returned by actuating the wiper operating lever. Coins having comparatively high magnetic properties will be slowed down by the magnet, and will drop off the end of the rail short of “accept” entrance and be returned.
Coins having little or no magnetic properties, such as brass or zine coins, will pass through the magnetic field so fast that they will overshoot the “accept” entrance and be returned.
A magnetic gate adjusted with too large a gap may pass both genuine and counterfeit coins. An adjustment with too small a gap can lead to rejection of some or even all coins. Over a period of time, the screw that adjusts the magnet gate has a tendency to work loose, resulting in a gradual narrowing of the gate. At first, only the thickest (i.e., newest) coins are rejected, As time passes, more and more coins are rejected until finally player complaints lead to the calling of the game repairman.
If pressing the coin rejector button does not cause the coin to be returned, and if the game still does not respond, then check the coin mechanism to see if the coin is jammed inside.
If you are certain that the coin is genuine, and that the coin passes through the coin mechanism and into the cash box, then the lack of game response is probably due to some kind of electrical trouble. Check for signals at the electrical contacts of the coin mechanism before moving on to the harness and other parts of the circuitry.
8.3.2. TV Monitor: The TV monitor is a self-contained unit housed in its own chassis. A trouble’s cause may be narrowed down to the monitor—cither by the substitution method using a known-to-be-good monitor. or by verifying presence of AC power to the monitor power supply and presence of the correct composite video signal. The entire monitor can then be removed from the game cabinet. Doing this facilitates troubleshooting steps, because all monitor components will then be accessible.
A schematic diagram of the monitor circuitry is included in section IX of this manual. After disconnecting and removing the monitor from the game. standard TV troubleshooting techniques are adequate for locating causes of trouble. Additional servicing information is available from the monitor manufacturer (Motorola)
AUDIO SIGNALS Table 8-1 Night Driver Signal Descriptions
SCHEMATIC SIGNAL FROM TO SIGNAL DESCRIPTION
ATTRACT ES (pin 5)
BANG Summing point of resistors
CRASH E5 (pin 22)
MOTOR SOUND
SPEED 1 D5 (pin 2) SPEED 2 D5 (pin 5) SPEED 3 D5 (pin 7) SPEED 4 D5 (pin 10)
SCREECH 1 C7 (pin 11)
SCREECH 2 C2 (pin 3)
SKID 1 D5 (pin 12)
SKID 2 D5 (pin 15)
AUDIO OUT- minus side PUT (SPEAKER) of 1000 yf Cap, C14. BANG input resistor R61 of Audio Amplifier A9.
D6 (pin 9) D7 (pin 9)
C8 (pin 11) D8 (pin 13)
MOTOR input resistor R60 of Audio Amplifier A9.
Resistor R11 Resistor R10 Resistor R9 Resistor R8
Screech 1 input resistor R59 of Audio Amplifier AY.
Screech 2 input resistor R58 of Audio Amplifier AQ.
C7 {pin 13)
C7 (pin 1)
Speakers High logic level during attract mode. From output port E5. Disable Motor Sound. BANG sound that is the result of a roadway pylon making contact with the car.
Low logic level from Output Port E5 that resets noise generator D6, D7.
Low logic level from Output Port £5 that enables BANG generator C8, D8.
Summed and modulated frequencies that depend upon the digital SPEED input of the motor generator.
Digital SPEED information from output port D5 that is converted into analog by summing resistors R8, R9, R10, and R11. Analog signal controls the oscillating frequency of oscillators A5, A6, and AZ. Screech audio signal of approximately 1KHz modulated by digital noise and gated through NAND gate C7 with SKID 1 signal.
Screech audio signal of approximately 833 Hz modulated by digital noise and gated through NAND gate C7 with SKID 2 signal.
Enabling signal for SCREECH 1 audio signal. From Output Port D5. Enabling signal for SCREECH 2 audio signal. From Output Port D5. Audio output from audio amplifier A9.
INPUT PORTS SIGNALS
ACC Accelerator Switch
GEAR 1 Gear shifter Ist gear Switch Edge Connector Pin P F9 (pin 1)
Edge Connector Pin H M9 (pin 12) Low logic level to F9 when accelerator foot pedal is depressed. Transferred to output of F9 only if address input is as follows: BAO —high logic level BA1—low logic level BA2—high logic level
Low logic level to M9 when gear shifter is in Ist gear position. Transfers to output 2Y only if address input is as follows:
SCHEMATIC SIGNAL | FROM TO SIGNAL DESCRIPTION
GEAR 2
GEAR 3
OPT OPT2 OPT3 OPI4
START Gear shitter 2nd gear Switch:
Gear shifter 3rd year Switch
110 (pin 15) L10 (pin 14) 110 (pin 6) 110 (pin 7)
START pushbutton Fdge Connector Pint M9 (pin 4i
Edge Connector Pink K9 (pin 12)
M9 (pin 10} M9 {pin 6) K9 (pin 10) KS {pin 6)
Edge Connector Pin 13 F9 (pin 2) BAO —low logic level BAIhigh logic level
low logic level to M9 when gear shifter is in 2nd gear position. Transfers to output 1Y only if address inputis as follows: BAO —low loxic level BA1—high logic level
Low Jogic level to K9 when gear shifter is in 3rd gear position. Lransfers to output 2Y only if address input is as follows BAO —low logic level BAI—high logic level
Logic inputto 1C0 and 2C0 inputs of multiplexers KI and M9. Transiers to 1Y and 2Y only if address Input is as follows BAG —low logic level BAI—low logic level
Logie level inputs of OPT] through OPT4 for given setting of hexadecimal switch L10 as (ollows
Switch
| Setting OPTI | OPT2 | OPT3. | OPT4 | |
| 0 | low | low | low | low |
| 1 | high | low | low | low |
| 2 | low | high | jow | low |
| 3: | high | high | low | low |
| 4 | low | low | high | low |
| 5 | high | low | high | low |
| 6 | low | high | high | low |
| 7 | high | high | high | low |
| 8 | low | low | low | high |
| 9 | high | tow | low | high |
| A | low | high | low | high |
| B | high | hign | low | high |
| Cc | low | low | high | high |
| D | high | low | high | high |
| E | low | high | high | high |
| F | high | high | high | high |
Low logic level to F9 when START pushbutton is depressed. Transfers to output of F9 if address input is as follows: BAO —low logic level BA1—high logic level BA2—low logic level
[SCHEMATIC | SIGNAL FROM TO SIGNAL DESCRIPTION
| STEER A | E8 (pin 9) | K9 (pin 13) | Steering direction input to multiplexer K9. Low logic |
level indicates right: turn. High logic level indicates left turn. Transfers to output 2Y of K9 if address input is as follows: BAO —high logic level BA1—high logic level Refer to Figure 8-1.
| STEER 1A | Steering Board | Edge Connector | Steering input from Steering Board Assembly. Leads |
| Assembly | Pin S | STEER 1B for right turn. Lags STEER 1B for left | |
| pin 8 | F9 (pin 9) | turn. Refer to Figure 8-1. | |
| STELR B | £8 (pin 5} | K9 (pin 3) | Steering rate input (the faster steering wheel is turned, |
the shorter the duty cycle of the pulse input) to multiplexer K9. Transfers to output 1Y of K9 if address input is as follows: BAO —high logic level BA1--high logic level Refer to figure 8-1.
| STEER 1B | Steering Board | Edge Connector | Steering input from Steering Board Assembly. Lags |
| Assembly | Pin 16 | STEER 1A for right turn. Leads STEER 1A for left | |
| pin 4 | E9 (pin 11) | turn. Refer to Figure 8-1. | |
| TEST, | TEST Switch | Edge Connector | Low logic level to K9 when TEST Switch is set to “on” |
Pin J position. Transfers to output of K9 if address K9 (pin 5) input is as follows: BAO —high logic level BA1—low logic level
| TRACK | track select | Edge Connector | Low logic level to F9 when track select switch is set to |
| SELECT 1 | Switch | Pin 14 | NOVICE TRACK position. Transfers to output of |
F9 (pin 15) F9 only if address input is as follows: BAO —low logic level BA1—-low logic level BA2—high logic level
| TRACK | track select | Edge Connector | Low logic level to F9 when track select switch is set to |
| SELECT 2 | Switch | PinR | PRO TRACK position. Transfers to output of F9 |
F9 (pin 14) only if address input is as follows: BAO —high logic level BA1—low logic level BA2—high logic level
| V BLANK | J7 (pin 10) | K9 (pin 11) | V BLANK pulse transfers from the input to the output |
of K9 only if address input is as follows: ABO —high logic level AB1—low logic jevel Refer to Insert 8-1. a
oe
a
ace YUTPUT PORTS SIGNALS
SCHEMATIC
SIGNAL FROM TO SCHEMATIC = SIGNAL
| BDO | F3 (pins 2 & 4) | D5 (pin 3) | SPEED 7 logic level same as BDO logic level when |
OUTO goes from low logic level to high logic level.
| BD1 | E3 (pins 12 & 14) | D5 (pin 4) | SPEED 2 logic level same as BD1 logic level when OUTO |
oes from low logic level to high logic level.
| BD2 | E3 (pins 2 & 4) | 5 (pin 6) | SPEED 3 logic level same as BD2 logic level when OUTO |
‘oes from low logic level to high logic level.
| BD3 | F3 (pins 5 & 7) | D5 (pin 11) | SPEED 4 logic level same as BD3 logic level when OUTO |
goes from low logic level to high logic level.
| BD4 | F3 (pins 12 & 14) | D5 (pin 13) | SKID 1 logic level same as BD4 logic level when OUTO |
goes from low logic level to high logic level.
| BD5S | E3 (pins 9 & 11) | 5 (pin 14) | SKID 2 logic level same as BDS logic level when OUTO |
goes from low logic level to high logic level.
| BDO | F3 (pins 2 & 4) | E5 (pin 3) | CRASH logic level same as BDO logic level when |
OUT goes from low logic level to high logic level.
| BD1 | E3 (pins 12 & 14) | E5 (pin 4) | ATTRACT logic level same as BD1 logic level when |
OUT1 goes from low logic level to high logic level.
| BD2 | £3 (pins 2 & 4) | E5 (pin 6) | Output not used. |
| BD3 | F3 (pins 5 & 7) | E5 (pin 11) | Logic level at N9 (pin 1) same logic level as BD3 when |
OUT1 goes from low logic level to high logic level.
| BD4 | F3 (pins 12 & 14) | E5 (pin 13) | Logic level as J8 (pin 11) same logic level as BD4 when |
OUT1 goes from low logic level to high logic level.
| BDS | E3 (pin 9 & 11) | E5 (pin 14) | Output not used. |
MICROPROCESSOR SIGNALS a —— ~
| ABO | C3 (pin 9) | 2 (pin 2) | |
| ABI | a. (pin 10) | 2 (pin 4) | |
| AB2 | (plo 11) | 2 (pin 6) | |
| AB3 | 3 (pin 12) | 2 (pin 10) | |
| AB4 | C3 (pin 13) | C2 (pin 12) | |
| AB5 | C3 (pin 14) | C2 (pin 14) | |
| AB6 | C3 (pin 15) | B2 (pin 2) | Address bus to 8T97 tri-state devices. Tri-state devices |
| AB7 | C3 (pin 16) | B2 (pin 4) | not used for high Z output, but instead only used |
| ABB | C3 (pin 17) | B2 (pin 6) | as signal buffer. |
| AB9 | C3 (pin 18) | B2 (pin 10) | |
| AB10 | C3 (pin 19) | B2 (pin 12) | |
| AB11 | C3 (pin 20) | B2 (pin 14) | |
| AB12 | C3 (pin 22) | B4 (pin 10) | |
| AB13 | C3 (pin 23) | B4 (pin 12) | |
| AB14 | C3 (pin 24) | B4 (pin 4) | |
| AB15 | C3 (pin 25) | B4 (pin 6) |
| SIGNAL From/To From/To SIGNAL DESCRIPTION
| DBO | C3 (pin 33) | F3 (pin 3) | |
| DBI | C3 (pin 32) | £3 (pin 13) | Bi-directional data bus to bi-directional buffers 8128. |
| DB2 | C3 (pin 31) | E3 (pin 3) | Data buffers E3 and F3 buffer the data signal from |
| DB3 | C3 (pin 30) | F3 (pin 6) | the Microprocessor through one path of E3 and |
| DB4 | C3 (pin 29) | F3 (pin 13) | F3 when R/W is low logic level and buffer the |
| DBS | C3 (pin 26) | £3 (pin 10) | data signal to the Microprocessor through |
| DB6 | C3 (pin 27) | £3 (pin 6) | another path when R/W is a high logic level. |
| DB7 | C3 (pin 26) | F3 (pin 10) |
MICROPROCESSOR SIGNALS (CONT)
SIGNAL FROM To SCHEMATIC SIGNAL
| IRQ | J7 (pin 14) | C3 (pin 4) | Interrupt request. This signal informs the Micro- |
processor that the vertical blanking period is beginning. Refer to Insert 8-1.
| RESET | C7 (pin 6) | C3 (pin 40) | This signal is the result of watchdog. Refer to Section |
IV, Theory of Operation, paragraph 4.4.
| R/W | C3 (pin 34) | B4 (pin 14) | Read/write signal is a Microprocessor signal derived |
from phase 2 and determines the direction of data to or from the Microprocessor.
| b2 | C3 (pin 39) | E4 (pin 9) | Phase 2: Basic timing signal of the Microprocessor. |
Refer to Section IV, Theory of Operation, subparagraph 4.3.3.
WATCH DOG SIGNALS
| V BLANK | 37 (pin 11) | L7 (pin 11) | The V BLANK pulse starts L7 to flip-flop. After three |
| WATCH | K7 (pin 9) | L7 (pins 1 & 13) | pulses a low logic level will appear at RESET. |
DOG However, this should never happen if the
| RESET | C7 (pin 6) | C3 (pin 40) | Micorprocessor address bus and read/write bus |
(BR/W) and Program Memory is operating properly. Program Memory instructs an address that is decoded by Enable J2 for an output of HFC (J2 pin 3). At the same time, the Microprocessor outputs a low logic level BR/W. These two signals are received by Decoder K7 (schematic sheet 3) through OR gate K8. The result is a low logic WATCH-DOG signal at the output of K7 (pin 9). If all is operating properly, WATCH-DOG will be present before flip-flop L7 reaches the count of three pulses.
PLAYFIELD SIGNALS (cont) "SCHEMATIC AL SIGNAL FROM To SIGNAL DESCRIPTION
| BAO | C2 (pin 3) | L2 (pin 13) | During V BLANK period (V BLANK is a high logic |
| BAI | C2 (pin 5) | L2 (pin 10) | level), BAO through BA6 address the Playtield |
| BA2 | C2 (pin 7) | L2 (pin 6) | RAM through multiplexers K2 and L2. Also |
| BA3 | C2 (pin 9) | L2 (pin 3) | BR/W is transferred through multiplexer K2. If |
| BA4 | C2 (pin 11) | K2 {pin 13) | BR/W is a low logic level, data is written into the |
| BAS | C2 (pin 13) | K2 (pin 10) | Playfield RAM via the Data Bus. |
| BA6 | B2 (pin 3) | K2 (pin 6) | |
| BR/W | B4 (pin 13) | K2 (pin 3) | During V BLANK period (V BLANK isa low logic level), |
| 8H | L3 (pin 14) | L2 (pin 14) | 8H through 128H, 16V, and 32V address the |
| 16H | L3 (pin 13) | L2 (pin 11) | Playfield RAM through multiplexers K2 and L2. |
| 32H | L3 (pin 12) | L2 (pin 5) | The read/write input of the Playfield RAM |
| 64H | L3 (pin 11) | L2 (pin 2) | becomes a high logic level (K2 1A input |
| 128H | J3 (pin 14) | K2 (pin 14) | transferred to 1Y output); thus the data written |
| 16V | H8 (pin 14) | K2 (pin 11) | into the Playfield RAM during V BLANK period is |
| 32V | H8 (pin 13) | K2 (pin 5) | now addressed (resulting in transferring the data |
to address the Playfield ROM) by horizontal and vertical timing signals.
| PFW | J2 (pin 2) | D4 (pin 1) | During V BLANK period all three signals would |
| PER | H2 jpin 1) | D4 (pin 2) | normally be high until Enable H2 receives an |
| V BLANK | J7 (pin 10) | D4 (pin 13) | address that results in a low logic level PFW |
signal. At this time there will bea high logic level output from NOR gate D4 (pin 12). This high logic level input to M2 (pin 10) enables the tristate data buffers of M2 to receive a data input. Refer to Insert 8-1
| Prw | }2 (pin 2) | M1 (pins 1 & 15) | Low logic level PFW signal enables tri-state device M1 |
so data may be written into the Playfield RAM M2.
| a | F8 (pin 14) | P2 (pin 21) | These three signals are the three least significant bits |
| 2v | F8 (pin 13) | P2 (pin 22) | of the Playfield ROM address. These bits |
| 4V | F8 (pin 12) | P2 (pin 23) | determine which horizontal line is to be scanned |
with what ROM data.
| 1H | K3 (pin 13) | J5 (pin 1) | These eight signals determine when Shift Register P3 | |
| 2H | k3 (pin 12) | J5 (pin 4) | loads data for displaying a character. Signals V | |
| 4H | K3 (pin 11) | J5 (pin 5) | BLANK and 256H determine that P3 will be | |
| 256H | J3 (pin 13) | J5 (pin 11) | loaded only during the horizontal scan period. | |
| V BLANK | J? (pin 11) | J5 (pin 6) | Signals 8V, 64V, and 128V determine that P3 is | |
| BV | L8 (pin 2) | J5 (pin 3) | loaded during horizontal scan lines zero | |
| 64V | J8 (pin 4) | J5 (pin 2) | through eight, sixteen through twenty-four, | |
| 128V | J8 (pin 8) | J5 (pin 12) | thirty-two through forty, and | forty-eight |
through fifty-six. Signals 1H, 2H, and 4H determine that P3 is loaded thirty-two times per enabled scan line.
——_—____l
2GHEM ANE IGNAL DESCRIPTION
SIGNAL FROM To SIG Si fe)
| 6MHz | K3 (pin 14) | P3 (pin 7) | When a low logic level pulse appears on load input of |
P3 (pin 15), the data input from the Playfield ROM is immediately clocked out as serial data from P3 (pin 13) at the rate of 6¢MHz.
| PLAYFIELD | P3 (pin 13) | K8 (pin 5) | Playfield video serial data generated by the Playfield |
circuitry.
ENABLE SIGNALS
| BA10 | B2 (pin 11) | H2 (pin 15) | These five signals enable the read address decoder H2. |
| BA11 | B2 (pin 13) | H2 (pin 14) | If Be 2 or BA15 is a low logic level, there will not |
| BA12 | B4 (pin 9) | H2 (pin 13) | be an output from Enable H2. The Enable |
| Bo2 | E4 (pin 6) | F4 (pin 10) | outputs for a given input are as follows: |
| BA15 | B4 (pin 7) | F4 (pin 9) |
BA15 Bb2 BA12BA11BA10 H2 Output Signal H2Pin #
| H | H | L-L | LoL | PFR. | pint | |
| H | oH | L | L | H | STEER RESET | pin 2 |
| H | H | L | HL | pin 3 | ||
| H | H | L | HoH | pin 4 | ||
| H | H | H | LoL | PROM 0 | pin 5 | |
| H | H | H | LH | PROM 1 | pin 6 | |
| H | H | H | H | oL | PROM 2 | (pin 7) |
| H | H | H | HH | PROM 3 | (pin 9) | |
| BAQ | B2 (pin 9) | J2 (pin 15) | These eight signals enable address decoder J2. If BA12, | |||
| BA10 | B2 (pin 11) | J2 (pin 14) | Be 2, BA13, BA14, or BA15 is a high logic level, | |||
| BAI | B2 (pin 13) | J2 (pin 13} | there will not be an output from Enable J2. The | |||
| BA12 | B4 (pin 9) | D4 (pin 3) | Enable output for a given input is as follows: |
E4 (pin 11)
| Bb2 | £4 (pin 8) | C4 (pin 5) |
| BA13 | B4 (pin 11) | C4 (pin 6) |
| BAI4 | B4 (pin 5) | C4 (pin 9) |
| BA15 | B4 (pin 7) | C4 (pin 8) |
BA15BA14BA13 B® 2 BA12BA11BA10 J2 Output Signal J2 pin #
| L | L | L | L | L | L | L | SCRAM | pin 1 |
| Loko | oto | obLobtotiou | PFW | pin 2 | ||||
| Loko | ok | tL | tb | HoL | AVC | pin 3 | ||
| Lo | otk | oto | ot | ot | oH | oH | INO | pin 4 |
| Loko | bob | H | LoL | INT | pin5 | |||
| L | L | L | LH | LH | OUT 0 | pin 6 | ||
| Lobo | oto | tL | H | HL | OUT1 | pin7 | ||
| LoL | obtobtoeoH | HH | not used | pin 9 |
L_ 1
?OWER SUPPLY VOLTAGES ISCHEMATIC To SIGN : SIGNAL FROM IGNAL DESCRIPTION
| Resistors | many locations | The symbol ‘‘P” stands for pull-up. This means that |
R1, R7, R48, R52 anywhere on the schematic that the symbol “P” and R112 appears, that point is connected directly to resistors R1,R7,R48,R52and R112. Therefore the circuit is “pulled-up” to +5 VDC one of those pull-up resistors.
| +5V | LM323 | many locations | This is the +5 VDC power to all integrated circuits on |
the PCB, except Audio Amplifier A9.
| +20V (DC, | Plus side | AQ (pins 9 & 11) | This is the +20 VDC unregulated power for the Audio |
| unreg) | of 4700 ufd | Amplifier. |
cap. C27.
VIDEO SIGNALS
| H SYNC | HS (pin 6) | P8 (pin 9) | These two signals are the horizontal and vertical sync |
| VSYNC | J7 (pin 6) | P8 (pin 10) | signals necessary to “kick” the TV_monitor |
scanning circuitry into a retrace. H SYNC is inverse of H SYNC and V SYNC is inverse of V SYNC, as illustrated in Insert 8-1.
| 256H | J3 (pin 13) | P8 (pin 2) | These two signals are the horizontal and vertical |
| V BLANK | J7 (pin 11) | P8 (pin 1) | blanking pulses necessary to drive the TV |
monitor into the black level during retrace. The combination of these two signals is COMP B at P8 (pin 3). Refer to Insert 8-1,
| ROADWAY | L8 (pin 6) | K8 (pin 4) | These two signals are the video serial data from the |
| PLAYFIELD | P3 (pin 13) | K8 (pin 5) | Playfield circuitry and the Roadway circuitry. |
The playfield consists of four possible horizontal rows of alpha numerics between horizontal scan lines zero and eight, sixteen and twenty-four, thirty-two and forty, and forty-eight and fifty-six. The Roadway consists of the fourteen roadway pylons.
| VIDEO | C8 (pin 3) | C6 (pin 9) | This signal is present anytime the roadway makes |
INVERT connection with the car. The signal is originated in the audio BANG circuit. Its function is to make the TV monitor display flash during the BANG sound period.
| 8v | F8 (pin 11) | C4 jpin 2) | These signals provide a backlight window at the |
| 16V | H8 (pin 14) | C4 (pin 3) | center bottom of the TV monitor display. Signal |
| 32V | H8 (pin 13) | N8 (pin 3) | V BLANK places the window on the TV monitor |
| 64V | HB (pin 12) | N8 (pin 2) | display during the horizontal scan time. The |
a)
SCHEMATIC
| SIGNAL | | | FROM | To | SIGNAL DESCRIPTION |
| 128V | H8 (pin 11) | N8 (pin 1) | vertical timing signals place the window | |
| 64H | L3 (pin 11) | C6 (pin 5) | between horizontal scan lines 232 and 240. The | |
| 128H | J3 (pin 14) | C6 (pin 4) | horizontal timing signals place the window in | |
| 256H | J3 (pin 13) | NB (pin 12) | the center of the TV monitor display and makes | |
| V BLANK | J7 (pin 11) | N8 (pin 6) | the width of the window equal to 128H. |
ROADWAY SIGNALS
| BDO | F3 (pins 2 & 4) | H6 (pin 4) | Data input to the vertical position read-only memory | ||||
| BD1 | £3 (pins 12 & 14) | H6 (pin 6) | (VP RAMs H6, P6). In order to write vertical | ||||
| BD2 | £3 (pins 2 & 4) | H6 (pin 10) | position data into the VP RAMs, POSV (H6, P6 | ||||
| BD3 | F3 (pins 5 & 7) | H6 (pin 12) | pin 3) must be a low logic level. The address | ||||
| BD4 | F3 (pins 12 & 14) | P6 (pin 4) | input is from the outputs of demodulator P5 | ||||
| BD5 | £3 (pins 9 & 11) | P6 (pin 6) | (pins 4, 7,9, and 12). During the V BLANK period, | ||||
| BD6 | £3 [pins 5 & 7) | P6 (pin 10) | data is stored in these VP RAMs for the vertical | ||||
| BD7 | F3 (pins 9 & 11) | P6 (pin 12) | position of all the roadway pylons. | ||||
| BDO | F3 (pins 2 & 4) | J6 (pin 4) | Data bus input to the horizontal position read-only | ||||
| BDI | £3 (pins 12 & 14) | J6 (pin 6) | memory (RAMs J6, L6). In order to write | ||||
| BD2 | £3 (pins 2 & 4) | J6 (pin 10) | horizontal position data into the RAMs, POS H | ||||
| BD3 | F3 (pins 5 & 7) | J6 (pin 12) | (6. L6 pin 3) must be a low logic level. The | ||||
| BD4 | F3 (pins 12 & 14) | L6 (pin 4) | address | input | is | from | the outputs of |
| BD5 | £3 (pins 9 & 11) | L6 (pin 6) | demodulator P5 (pins 4, 7,9, and 12). During the | ||||
| BD6 | E3 (pins 5 & 7) | L6 (pin 10) | V BLANK period, data is stored in these RAMs for | ||||
| BD7 | F3 (pins 9 & 11) | L6 (pin 12) | the horizontal position of all of the roadway |
pylons.
| BDO | F3 (pins 2 & 4) | E6 (pin 4) | Data bus input to the character picture read-only |
| BD1 | £3 (pins 12 & 14) | E6 (pin 6) | memory (RAMs E6, M6). In order to write |
| BD2 | £3 (pins 2 & 4} | E6 (pin 10) | character picture data into the RAMs, CHAR |
| BD3 | F3 (pins 5 & 7) | E6 (pin 12) | must be a low logic level. The address input is |
| BD4 | F3 (pins 12 & 14) | M6 (pin 4) | from the outputs of demodulator P5 (pins 4,7, 9, |
| BD5 | £3 (pins 9 & 11) | M6 (pin 6) | and 12.) During the V BLANK period, data is |
| BD6 | £3 (pins 5 & 7) | M6 (pin 10) | stored in these RAMs for the size and width |
| BD7 | F3 (pins 9 & 11) | M6 (pin 12) | (character picture) of the roadway pylons. |
| BA4 | C2 (pin 11) | K7 (pin 14) | Address signals BA4 and BAS select the outputs of K7 as |
| BAS | €2 (pin 13) | K7 (pin 13) | in the following table. If at any time HVC or BR/W |
| HVC | J2 (pin 3) | K8 (pin 9) | is u low iogic level, all of the outputs of K7 will be |
| BR/W | B4 (pin 13) | K8 (pin 10) | alow logic level. |
BAS BA4 Decoder K7 output
| L | L | POS H |
| L | H | POs V |
| H | L | CHAR |
| H | H | WATCH-DOG |
| COMP B | L8 (pin 4) | Composite blanking signal. During the vertical blanking |
period and horizontal blanking period, this is a low fogic level. During the horizontal scan period, this is a high logic le Refer to Insert
IscHEMATIC FROM To SIGNAL DESCRIPTION SIGNAL
| PSAI | L2 (pin 12) | P5 (pin 3) | Picture sync/address signals. These signals are the |
| PSA2 | L2 (pin 9) | PS (pin 6) | address signals for the vertical position RAM (H6, |
| PSA3 | L2 (pin 7) | P5 (pin 10) | P6}, horizontal position RAM (J6, L6), and |
| PSA4 | L2 (pin 4) | P5 (pin 13) | character RAM (£6, M6). During the vertical |
blanking period, the address signal comes directly from the four least significant bits of the address bus (BAO through BA3, inputs L2 pins 13, 10, 6, and 3). During the vertical non-blanking period and during horizontal blanking, the address signal comes directly from horizontal synchronization 8H, 16H, 32H. and 64H (inputs L2 pins 2, 5, 11, and 13).
| VPI | H6 (pin 5) | F7 (pin 10) | Vertical position data signals. These signals are applied |
| VP2 | H6 (pin 7) | F7 (pin 8) | to a coarse (N7) and fine (F7) vertical line |
| VP3 | H6 (pin 9) | F7 (pin 3) | comparator. When the vertical line comparator |
| VP4 | H6 (pin 11) | F7 (pin 11) | vertical synchronization inputs IV through 128V |
| VP5 | P6 {pin 5) | N7 (pin 10) | match the vertical position data signal, the |
| VP6 | P6 (pin 7) | N7 (pin 8) | coarse and fine vertical line comparator (F7,N7) |
| vP7 | P6 (pin 9) | N7 (pin 3) | outputs will all be a high logic level. |
| VP8 | P6 (pin 11) | N7 (pin 11) | |
| PICT | E6 (pin 5) | E7 (pin 9) | Picture height data signals. These signals determine |
| PIC2 | E6 (pin 7) | E7 (pin 11) | the height of the data roadway pylon to be |
| PIC3 | E6 (pin 9) | E7 (pin 14) | displayed. For example, if the pylon is only to be |
| PIC4 | E6 (pin 11) | E7 (pin 1) | six vertical lines high, PIC data signal code will be |
0111 (7). When VP1 through VP4 is equal to IV through 8V, the outputs of F7 will all be a high logic level. Beginning with the next vertical line, the outputs of F7 will begin counting down. When the “A” inputs of E7 reach the count of six, output A<B E7 (pin 7) will be a high logic level.
| 56H | E4 (pin 2) | KS, J5 (pin 1) | Horizontal timing signal that represents the horizon- |
tal blanking period when it is a high logic level. During norizontal blanking, horizontal position signals (HP1 through HP8) are transferred to the outputs of multiplexers K5 and L5. During the horizontal scan time, horizontal timing signals (1H through 128H) are transferred to the outputs of multiplexers K5 and L5.
| 256H | J3 (pin 13) | N3 (pin 12) | Horizontal position address inputs to match RAM |
(M4) and object RAMs(H4, }4, K4, and L4) during horizontal blanking. If the horizontal blanking period is preceding a horizontal scan line on which a roadway pylon is to be displayed, R/W (pin 12 0f match and object RAMs) will receive a low logic level from the output of the vertical line comparator (P8 pin 6). Therefore data is written into the match and object RAMs. The
SCHEMATIC SIGNAL FROM TO
data written into the match RAM is a low logic level for RAM address locations (output of N3 pin 9). The data written into the object RAMs is PA1 through PA4.
| PAI | P5 (pin 4) | L4 (pin 13) | During horizontal blanking period, these signals are |
| PA2 | P5 (pin 7) | K4 (pin 13) | from horizontal timing signals 8H, 16H, 32H and |
| PA3 | P5 (pin 9) | J4 (pin 13) | 64H (inputs to multiplexer L2). These signals are |
| PA4 | P5 (pin 12) | H4 (pin 13) | the data input to the object RAMs L4, K4, J4, and |
H4.
| V BLANK | J7 (pin 10) | M4 (pin 3) | During a horizontal scan line that is going to display a |
| CLK* | N4 (pin 8) | N3 (pin 3) | roadway pylon, the match RAM and object |
| COMP B | P8 (pin 3) | N3 (pin 1) | RAMs are addressed by timing signals 1H |
| MATCH | N3 (pin 5) | N5 (pin 9) | through 128H. Therefore the address input |
| MATCH. | N3 (pin 6) | P8 (pin 5) | changes at a rate of 1H 256 times during a |
horizontal scan line. When the address comes to a point where a low logic level has been stored in the match RAM, one 12 MHz (CLK*) pulse later, match latch N3 output pin 5 becomes a high logic level. This results in the inverse data output of the object RAMs through flip-flop N5.
| BJO | N5 (pin 3) | PS5 (pin 2) | Roadway object address signal. During the scan line, |
| OBJ1 | N5 (pin 6) | P5 (pin 5) | these signals address the Roadway character |
| OBJ2 | N5 (pin 11) | P5 (pin 11) | RAM M6 through multiplexer P5 if MATCH |
| OB)3 | NS (pin 14) | P5 (pin 14) | signal goes to a high logic level. The signals cause |
a data output from roadway picture RAM E6.
| PICS | M6 (pin 5) | M5 (pin 15) | Roadway picture signals PIC5 through PIC8 are |
| PIC6 | M6 (pin 7) | MS (pin 1) | applied directly to the inputs of shift register M5. |
| PIC7 | M6 (pin 9) | MS (pin 10) | Since MATCH is a low logic level, the PICS |
| PIC8 | M6 (pin 11) | MS (pin 9) | through PIC8 signals are immediately clocked |
| MATCH | N3 (pin 6) | M5 (pin 11) | out of shift register at a 6-MHz rate. This signal, |
| ROADWAY | [8 (pin 6) | K8 (pin 4) | called the ROADWAY signal, is fed directly to |
the video output.
PROM SIGNALS
| BDO | H1, J1, K1, | F3 (pins 2 & 4) | These signals make up the data bus from Program |
11 (pin 14) PROMs (C1, D1, E1, F1, H1, J1, K1, L1) to the
| BD1 | H1, J1, K1, | E3 (pins 12 & 14) | Microprocessor (schematic sheet 3). This data |
L1 (pin 13) bus is unidirectional (one direction only) and
| BD2 | H1, J1, K1, | £3 (pins 2 & 4) | goes only from Program PROMs to the |
11 (pin 12) Microprocessor.
| BD3 | H1, J1, K1, | F3 (pins 5 & 7) | These signals are an output of Program PROMs as a |
11 (pin 11) result of an address input to Program PROMs.
| BD4 | C1, D1, E1, | F3 (pins 12 & 14) | Program PROMs are only addressed by the ten |
FI (pin 14) least significant bits of the address bus.
| BDS | C1, D1, £1, | E3 (pins 9 & 11) |
F1 (pin 13)
SCHEMATIC FROM To SIGNAL DESCRIPTION SIGNAL
| BD6 | C1, D1. £1, | E3 (pins 5 & 7) |
FI (pin 12)
| BD7 | C1, D1, £1, | F3 (pins 9 & 11) |
fl
| BAO | C2 (pin 3) | C1, D1, £1, F1, | These signals are the ten least significant bits of the |
H1,J1, K1, 11 address bus from the Microprocessor. An (pin 5) address input to Program Memory will resultina
| BAI | C2 (pin 5) | C1, D1, E1, F1, | data output. The individual PROM integrated |
H1, $1, K1, 1 circuit pairs selected are determined by the (pin 6) enabling signal. All PROM chips are not used at
| BA2 | C2 (pin 7) | C1, D1, £1, F1, | the same time. |
H1, J1, K1, L7 (pin 7)
| BA3 | C2 (pin 9) | C1, D1, E1, F1, |
H1, f1, K1, L1 (pin 4)
| BA4 | C2 {pin 11) | C1, D1, £1, F1, |
H1, J1, K1, 11 (pin 3)
| BAS | C2 (pin 13) | C1, D1, E1, F1, |
H1, J1, K1, 1 (pin 2)
| BAG | B2 (pin 3) | C1, D1, £1, F1, |
H1, J1, K1, L1 (pin 1)
| BAZ | B2 (pin 5) | C1, D1, E1, F1, |
H1, 1, K1, 11 (pin 17)
| BAS | B2 (pin 7) | C1, D1, €1, F1, |
H4, J1, K1, 1 (pin 16)
| BA | B3 (pin 9) | C1, D1, E1, F1, |
H1, j1, K1, U1 (pin 15)
| PROMO, | H2 (pin 5) | C1, H1 (pin 8) | These are the ROM enabling signals. With a low logic |
| PROM 1 | H2 (pin 6) | D1, J1 (pin 8) | level signal the individual pairs of ROMs are |
| PROM 2 | H2 (pin 7} | E1, K1 (pin 8) | enabled. The term PROM is an abbreviation for |
| PROM 3 | H2 (pin 9) | F1, L1 (pin 8) | programmable read-only memory. The PROMs. |
are programmed by Atari specifically for the Night Driver game. These PROMs have the capability of being programmed only once. Therefore, for all practical purposes these eight chips may be referred to as ROMs. _|
PAGE ZERO SIGNALS
SCHEMATIC
| SIGNAL | FROM | TO | SIGNAL DESCRIPTION |
| BAO | C2 (pin 3) | Al, B1 {pin 4) | These are the address bus signals to the Page Zero |
| BAI | C2 (pin 5) | A1, B1 (pin 3) | (Scratch Pad) Memory. With an address code |
| BA2 | C2 (pin 7) | Al, B11 (pin 2) | input to Page Zero Memory, the Microprocessor |
| BA3 | C2 (pin 9) | A1, B1 (pin 1) | writes a data code into the Memory. At this time |
| BA4 | C2 (pin 11) | A1, B1 (pin 175 | it is necessary for the read/write (R/W) input |
| BAS | C2 (pin 13) | A1, B1 (pin 5) | (A1, B1 pin 16) to be a low logic level and output |
| BA6 | B2 (pin 3) | A1, B1 (pin 6) | disable (OD) input (A1, B1 pin 9) to be a high |
| BA7 | B2 (pin 5) | Al, B1 (pin 7) | logic level. The data recorded into the Page Zero |
Memory can later be read by the Microprocessor if the R/W input is a high logic level and OD is a low logic level. An address input will then cause the output of data that was previously stored at that address location.
| sea re | From/To | From/To | SIGNAL DESCRIPTION |
| BDO | F3 (pins 2 & 4) | Al (pin 11) | These are bi-directional data lines from the |
| BD1 | E3 (pins 12 & 14) | Al (pin 12) | Microprocessor to the Page Zero Memory or to |
| BD2 | £3 (pins 2 & 4) | Al (pin 13) | the Microprocessor from the Page Zero |
| BD3 | F3 (pins 5 & 7) | Al (pin 14) | Memory. The determining factor_as to the |
| BD4 | F3 (pins 12 & 14) | B1 (pin 11) | direction of the data signal is the R/W signal and |
| BD5 | £3 (pins 9 & 11) | B1 (pin 12) | the OD (A1,B1 pin 9) signal. If the data signal is to |
| BD6 | E3 (pins 5 & 7) | B41 (pin 13) | the Page Zero Memory, OD must be a high logic |
| BD7 | F3 (pins 9 & 11) | B1 ipin 14) | level. If the data signal is from Page Zero |
‘ Memory, OD must be a low logic level.
SCHEMATIC
| SIGNAL | FROM | TO | SIGNAL DESCRIPTION |
| BR/AW | B4 (pin 13) | £4 (pin 3) | Read/write bus. This signal is a high logic level when |
data is read from the Page Zero Memory and a low logic level when data is written into Page Zero Memory.
| Bb2 | E4 (pin 6) | F4 (pin 5) | Phase 2 bus. This is a timing signal from the Micro- |
processor. When Bb 2 is a high logic level, data is manipulated to and from the Microprocessor. Refer to Section IV, subpapragraph 4.3.3.
| SCRAM | J2 (pin 1) | A1, B1 (pin 15) | Scratch Pad RAM (Page Zero Memory) enable. This |
signal originates in the Enable (Address Decoder) J2. This signal must be a low logic level before Page Zero Memory will operate.
IX. SCHEMATICS, DRAWINGS, AND
NUMBER
A006 264-01
A006 262-01
A006547-01
A006321-01
A000607
006543-01
(none) PARTS LIST
TITLE
Parts List and Drawing Final Assembly
Parts List and Drawing Dashboard Assembly
Drawing Electronic Tray Assembly
Parts List, Drawing, and Schematic Night Driver PCB
Parts List, Drawing, and Schematic Steering Board PCB
Schematic Harness
Schematic Motorola Model XM701-10 TV Monitor
ASSEMBLY TITLE PINAL ASSEMBLY P/Lacos264-01 ASSEMBLY TITLE FINAL ASSEMBLY P/Lacos26a-01 REV. 1 PARTS LIST SPECIFICATION Page 1 of 2 PARTS LIST SPECIFICATION Page2 of 2 Drawn Barney Huang Item Part Number Qty. Description
ATARI Checked Mech. Eng. Innovative Kee Games| Proj. Eng. Elec. Eng. Rev. 40 78-25001 leisure arlen =F al 4006544-01 Mfg. Eng. a 42 006543-01 43 TM-080 44 006305-01 A pap aa 9/30/74 45 82-1824
3 | Rev per ECN 3073 0/5/76 C| Rev per ECK 3098 0/13/76 D__| Rev pér ECN 3110 0/15/7 Screw Down Tie Wrap Main Harness Harness Schematic ‘Tach Manual Poly Bay Wood Screws, #8 x 1.25" Lg. Flat Ha. Phil.
Rev. Description Date |Apprv Rev. Description Date |Apprv.| Aadade
[Item Part Number Qty. Description
2006234-02 A006262-01 A006263-01 A006547-01 A003637-11 A006315-O1 4005912 -01 A006690-01 006237-0: 10 A006245-01 il A005906-0: 12 060869-01 13 002728-01 14 005233-01 A, 15 A006572-01, 16 006251-02 17 006571-01 7A 005843-0. 18 72-6608 19 75-99090006 20 82-8016 21 003053-01 22 A006321-01 23 72-5524 24 75-015s 25 75-045 26 75-9158, 27 73-77002 28 75-5124B 29 75-040 30 75-9115 31 75-0108 32 72-6812 33 75-5132N 34 72-6820 35 48-004 36 75-931 37 72-6610 38 006329-01 39 A0062FA-01 Cabinet Assembly with Graphics Dashboard Assembly T.V. Shelf Assembly Electronic Tray Assembly Coin Door Assembly Single Foot Pedal Assembly R.F. Shield Box Assembly R.F. Board Assy (N.Driver Black-Lite Display Assy Display Assembly Rear Door Assy Speaker Grill. Bracket, Panel Mtg. Rear Door Seal Bezel, 23" Monitor (Silkscreened Plex, Main Display Plex, Attraction Panel (Silkscreen, £ | Plex, Light Box Panel Screw, Sm. Pan Hd., #6 x .50" Lg. Well Nut, Blind Hole Fastener Screw, Button Hd., Socket 10-32 x 1.00" Lg
Plex Retainers P.C. Board Assy Screw, Mach, Hex. Ha., Stl 4-20 x 1.50" Lg.
Washer, Flat i Washer, Split Lock Nut, Mach, Hex, 4-20 Pop Rivet, 3/16 0.D. x 3/4" Lg. Carriage Bolt, 10-24 x 1.50" Lg. Washer, Split-Lock #10 Nut, Hex, Hd., #10-24 Washer, Flat #10 Screw, Sm., Pan Hd., Phil., #8 x 3/4 Lg Carriage Bolt, 10-24 x 2.00" Lg. Screw, Sm., Pan Hd., Phil., #8 x 1.25 Lg
4" Speaker 10-24 Wing Nut Screw, Sm., Pan Hd., Phil., #6 x 5/8" Lg
Copy Right Decal Shipping Container
Hams or an & Add dtd dda Caan gM woondd rN goO0oao cae Sagan ATS a
E003 e a ai) aos z aoe 7 $6) 6.002 N ome ~ @) aonz
NIGHT DRIVER i ASSEMBLY TITLE DASHBOARD ASSY ATART PARTS LIST SPECIFICATION | Mech, Eng, Innovative «ee Games| Proj. Eng. Elec. Eng. Rev. leisure Mfg. Eng. c
| Rev. | Description | Date |Apprv. Rev. | Description | | Date [appre] |
| A | oD | REL | 9/30/7 | |
| B | Rev per ECN 3096 | 0/12 | ||
| c | Rev per ECN 3131 | 10/22/7 |
i
[
| Item | Part Number | Qty. | Description |
| 1 | 006261-01 | 1 | Control Panel with Graphics |
| 2 | 006248-01 | 1 | Control Panel (Top-Wood) |
| 3 | 006249-01 | 1 | Control Panel (Main-Wood) |
| 4 | 00059 8-03 | 1 | Steering Wheel Assy, (10" Dia Wheel) |
| 5 | 85-22F112 | 10 Screw, Mach., Pan Hd., Phil., #10-24, 3/4 Lg. Type F. | |
| 6 | 000567 | aa | Bow Washer |
| 7 | A000608-02 | 1 | N-Shift Assembly |
| 8 | 005255-01 | 1 | Shift Bezel |
| > | 75-010S | 4 | #10 Flat Washer |
| 10 | 75-015S | 4 | #4-20 Flat Washer |
| il | 75-045 | 4 | #4-20 Lock Washer |
| 12 | 75-9158 | 4 | #4-20 Hex Nut |
| 13 | 75-5524B | 2 | #4-20 x 1.50" Lg. Carriage Bolts |
| 14 | 75-5524N | 2 | #4-20 x 1.50" Lg. Carriage Bolts |
| 15 | 62-002 | 1 | Led Switch |
| 16 | 001856-01 | 1 | Aluminum Bushing, Switch |
| 17 | 61-081c | 1 | Rocker Switch Snap in Bezel (Gold Contacts, Dry Circuit) |
| 18 | A006546-01 | 1 | Control Panel Harness |
| 19 | 72-6610 | 3 | Screw, Sm., Pan HD., Phil., #6 x 5/8 "Lg. |
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
NIGH
ASSEMBLY TITLE ECTRONICS TRAY ASSY 006547-01
PARTS LIST SPECIFICATION Page lof _1_
va Drawn NEXT ASSY A006264-01 ATARI Checked Mech, Eng.
| Innovative KEE Games| Proj. Eng. | Elec. Eng. | Rev. | ||
| leisure | so at | Mig. Eng. | ! | |
| Rev. | Description | Date |Apprv Rev. | Description | Date |Apprv,| |
EN 9/30/76 B_ | Rev per ECN 3079 10/6/76; Cc |Rev per ECN 3100 10/13/76! D_ [Rev per ECN 3119 |
| Item | Part Number | Qty. | Description | |||
| 1 | 006250-01 | 1 | Electronics Tray | | | |||
| 2 | 2006545-01 | 1 | Power Supply Harness | |||
| 3 | 001551-01 or -02 | 1 | Transformer, 001551 | |||
| 4 | 000622-01 | 1 | Cover, Transformer | |||
| 5 | 000871-01 | 1 | Label | |||
| 6 | 46-201202 | 2 | Fuse, 2 Amp | |||
| 7 | 79-3202 | 2 | Fuse Holder | |||
| 8 | 68-002 | 1 | Interlock Switch | |||
| 9 | 000268-02 | 1 | Bracket, Switch Mounting | |||
| 10 | 41-2001 | 1 | Filter, Power Line | |||
| 1 | a006550-01 | 1 | Mini-Harness | |||
| 12 | A006222-01 | 1 | Power Cord Assy, 8 Ft | |||
| 13 | A006447-01 | 1 | Power in On-Off Switch Harness | |||
| 14 | A006448-01 | 1 | Power Out On-Off Switch Harness | |||
| 15 | A006449-01 | 1 | On-Off Switch Assy | |||
| 16 | 78-25001 | 1 | Screw Down Tie Wrap | |||
| 17 | A001921-01 | A/R |) Shorting Block, 95V | ||||
| 18 | A001921-02 | " | " | Ls | 1lov | |
| 19 | A001921-03 | " | " | " | 220V H | |
| 20 | A001921-04 | 7 | " | " | 220V L | |
| 21 | A006555-01 | 1 | PC Board, Rectifier | |||
| 22 | 29-053 | 1 | Capacitor, Sprague Electrolytic 26,000 uf @15V | |||
| 23 | 78-70501SC | 1 | Bracket, Capacitor Mounting Sprague #4586-48 | |||
| 24 | 72-6608 | 6 | Screw, Sm, Pan Hd, Phil #6 x 4 Lg. | |||
| 25 | 72-6612 | 8 | " | SS | " | “#6 x 3/4 Lg. |
| 26 | 72-6812 | 7 | " | _* 3 | "#8 x 3/4 Lg. | |
| 27 | 75-2820B | 1 | Screw, Mach., Rd Hd, Brass #8 - 32 x 14 Lg. | |||
| 28 | 75-918B | 1 | Nut, Mach, Brass, #8-32 |
fs a [moe cone Bone nse C “OUTSTANDING ECNS
PRIMARY _SEC ONDARY Oe
1 DRAWING
DO NOT SCALE
ORY BURR [ OR GY OR
1&3 19 2 1 Io
NIGHT ORIVER
2ge8 ae i ELECTRONICS TRAY GN BR OV R/T GN By BU ASSEMBLY TRANSE WIRE COLORS AQ06547-0] ne
NIGHT DRIVER A. ATARI Innovative KEE GAMES leisure : ASSEMBLY TITLE ‘Assy, Night Driver P.C.B. P/L aooss2i1-01
PARTS LIST SPECIFICATION Page lof _4_
Drawn H. Slade Checked Mech, Eng. ASSEMBLY TITLE Assy, Night Driver P.C.B. PARTS LIST SPECIFICATION
Item Part Number g P/L acoss21-01 REV.A Page 2 of 4
Description
Proj. Eng. Elec. Eng, Rev.
Mig. Eng.
[ Rev. Description Date |Apprv] Rev. Description Date _|Apprv.
A PROD REL.
Item Part Number Qty. Deseription
ae woe it 008322-01 10-5470 10-5101 10-5151 10-5221 10-5331 10-5471 10-5102 10-5222 10-5332 10-5392 10-5472 10-5682 10-5822 10-5912 10-5103 10-5183 10-5271 10-5473 40-5104 10-5224 10-5474 10-5105 10-5225 10-5681 aus coy wae ANA aaa daa Printed Circuit Board
Resistor, Resistor, Resistor, Resistor, Resistor, Resistor, Resistor, Resistor, Resistor, Resistor, Resistor, Resistor, Resistor, Resistor, Resistor, Resistor, Resistor, Resistor, Resistor, Resistor, Resistor, Resistor, Resistor, Resistor, Carbon Comp, Carbon Comp, Carbon Comp, Carbon Comp, Carbon Comp, Carbon Comp, Carbon Comp, Carbon Comp, Carbon Comp, Carbon Comp, Carbon Comp, Carbon Comp, Carbon Comp, Carbon Comp, Carbon Comp, Carbon Comp, Carbon Comp, Carbon Comp, Carbon Comp, Carbon Comp, Carbon Comp, Carbon Comp, Carbon Comp, Carbon Comp, 1/4w, 5%, 5%, 5%, 5%, 5%, 5%, 5%, 5%, 5%, 5%, 5%, 5%, 5%, 5%, 5h, 5%, 5%, 5%, 5%, 5%, 47 ohm 100 ohm 150 ohm 220 ohm 330 ohm 470 ohm 70-73, 75-82 94-98,
1K ohm 2.2K ohm R54, 63-66, , 3.3K ohm R45, ! 3.9K ohm R56, 100 4.7K ohm R62 6.8K ohm R15, 61 8.2K ohm R46, 55 9.1K ohm R43 10K ohm R44, 60 18K ohm R17 270 ohm 47K ohm R47, 58, 59 100K ohm R12,90 220K ohm R8,13 470K ohm R9 1Megohm 2,2Megohm R11 680 ohm R83 R16, 42 R51 R49, 50, 68 R4, 5, 109 R19, 20, 22, 25, 101-104, 113 Ri, 2,7, 18, 21, 23,24, 26-41, 48,52, 88,67, | 69, 89, 112 99,105,106 | R108 R10 R6 10-5184 12-5151 19-8D9W2P0 19315502 19-315504 27-250102 27-250103 27-250104 27-250304 21-101224 28-101221 29-006 24-250105 24-250225 24-250106 24-250226 24-250476 24-250227 24-250108 24-250478 31-1N914 32-1N962B 38-MV5013 34-2N3643 37-7400 37-7402 37-7404 37-7408 37-7410 37-7414 37-7430 37-7432 37-7442 37-7474 37-7483 37-7485, 37-7486 37-7492 37-74107 37-74151 37-74153 37-748157 37-74164 37-74166 Hoadnntae QZ AMAA Ae ddd dda daa tO AAA AH Add a Resistor, Carbon Comp, 1/4w, 5%, 180K ohm R110 Resistor, Carbon Comp, 1w, 5%, 150 ohm RST
Resistor, Wirewound, 20w, 2 ohm Potentiometer, 5K Potentiometer, 100K Capacitor, Ceramic Dise, 25V, Dise, 25V,
Capacitor, Capacitor, Capacitor, Capacitor, Capacitor, Capacitor, Capacitor, Capacitor, Capacitor, Capacitor, Capacitor, Capacitor, Capacitor, Capacitor, Cerat Ceramic Disc, 25V, .1luf Ceramic Disc, 25V, Mylar, 100V, .22uf Dipped Mica, 100V, Tantalum, 35V, luf Electrolytic, Electrolytic, Electrolytic, Electrolytic, Electrolytic, Electrolytic, Electrolytic, Electrolytic, Diode 1N914 Diode, Zener, 1N962B LED, Red, Transistor 1.C. 7400 7402 7404 7408 7410 7414 7430 7432 7442 TAT4 7483 7485 7486 7492 74107 74151 74153 SRckoEoRoMcoRoEoReRoRsReRcRoRoRoRe) I.C. 74164 C. 74166 MV5013 2N3643 748157 or 93522 25v, 25v, 25v, 25v, 25v, 25v, 25, 25v, luf 2, 2uf louf 22uf atu 220uf 1000uf 4700uf 001uf .Oluf -33uf 220pf R74 R11 R14 C5,7,9,23 C18, 24 C1, 19, 20, 22, 25, 26, 28-50 c1z 6,11 cai C4 c1z C3, 15,16 c10 c13 c8 ce cu c27 CR1,2,3 cR4 CR5,6,7 @,3 HB, F4,C7 c4 E4,N4, L8 BS, PS D4 38, E9 35, P7, NB KB A2,H2, J2 N3, H5, L7, E8 F7,N3 E? C6 M3 D8 F9 K9, M9 K2, L2,K5, Ls, PS D6, D7 P3
+ Item Part Number ASSEMBLY TITLE Assy, Night Driver P.C.B. PARTS LIST SPECIFICATION Qty. P/L Ac06s21-01 = REV. A Page 3 of 4
Description
ql it 37-74174 37-74175 37-748175 37-74191 37-74193 37-9316 37-9321 37-555 37-566 37-MF C6040 37-MFC3040 37~LM324 37-8T97 37-8T28 37-TDA1004 37-LM323 90-6010 90-7002 90-7005 90-7008 90-7015 006559-01 006560-01 006561-01 006562-01 006563-01 006564-01 006565-01 006566-01 006567-01 006568-01 006569-01 006570-01 90-102 66-014P2T 66-114P1T 79-42540 78-06001 78-16005 78-06009 78-13016 006457-01 72-1608C 75-0168 AHHH HAO tea ry Le D5, E5 I.C. 74175, J7 I,C. 748175 N5 I.C. 74191 MS 1.C. 74193 c8 1.c J3,K3, L3, F8,
I.C, 9321 KT I.C, 555 co I.C, 566 A5, A6,A7 1.C. MFC6040 BT 1.C. MFC3040 B6 1.C, LM324 BS 1.C. 8T97 or 74367 M8,M1, B2, C2, B4 I.C, 8728 £3, F3 1.C., Audio Amp, TDA1004 Ag
1.C., Regulator, LM323 1c. c3 LC M2 E6, H6, J6, M6, P6, Lé RAM 82816 H4, J4,K4, M4, RAM 2111-A Al, B1 PROM, Syne HT PROM 1 H1 PROM 2 cl PROM 3 al PROM 4 DL PROM 5 Kl PROM 6 El PROM 7 Li PROM 8 Fl PROM, Alpha-Numeric P2 MASK ROM 1 D2 MASK ROM 2 E2 Crystal, 12.096Mhz Y1 DIP Switch, Hexa~-Decimal L10 DIP Switch, 4PST M10
Socket, 40-Pin Heatsink, LM323 Sil- Pad Heatsink, TDA1004 Cement, Heatsink Buss Bar, 13-Post Screw, Machine, Pan Hd., Phillips, #6-32 x 1/2" CRES
Washer, Flat, #6 Item Part Number ASSEMBLY TITLE Assy, Night Driver P.C.B.
ee PARTS LIST SPECIFICATION Qty. P/L aoves21-01 REV. A Page 4 of 4
Description
75-056 75-916C 10-5391 31-A14F oa Washer, Lock, Internal Star #6 Nut, Hex, #6-32, CRES Resistor, Car. Comp, %W, 5%, 390 ohm
Diode, Al4F R107 CR8,9
NOTES:
- MCF3040 To Replace MFC6040 When Stock is
Depleted. ** Use Item 118, MASK ROM1, In Position D2 To Replace Items 109,110,111 & 112. Use Item 119, MASK ROM 2, In Position F2 To Replace Items 113,114,115 & 116.
HOR\E & VER TIMING
- Bane
SCREECHT
ADDI SCREECH2
eas HUY HVA i le aK le
BTLMPE 040) pag BEMFC3340 aie (212, MoTOR > SOUND che yy paren ewe gay Wee BONS T 4133 PSeick
- snows pire. STEERIA ERS +8u sl ‘ BeOS 4 220 5 veAck ser +s srare,
ROR
STEER RESET To [Etsy sTzer l
0 LE opts 2B 2|4 —opre ® 4\e—opra 5 al —oere
INPUT PORTS
$20v Ror ae wis ly li 6B AD Rvo | & TDA woToR Wp SOUND ion RS9 le on seReeca1 Wy Sot f" Rs senecenz = ae Aik TF
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
vy
PLAYFIELD
+sv
PLAYFIELD
lan
\ a
i 2 oh am
i zh
ab.
ep
ae 1p
! Sas vevme 256H 205s 3 Sle" Vera —_ 2} 8S oF Rom? = 9000 008 ROADWAY ae ‘o Puavrie.o 22. E/Nioes
VIDEO INVERT D] van
j = z +s 3 +5Y INDICATOR Aa ees 5 mvsora $ "
ROE
9 $20 pe urea) z, R57 2 Sis0 sas w 1
Balhae 22 ANSSZB a
cRA
R_SUPPLY ‘OUTSTANDING ECNs
SCHEMATIC
NIGHT DRIVER
ID | “ooezei-01 Pes ie es
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
us ‘nl eS
NOTES
- DBE THIS ASSEMBLY WITH ©06322-O1 REVISION A” PC. BOaeDS.
MODIFICATIONS I. COT AND LIFT Pin 3 OF SS (7430).
- JUMPER PIN HOF FE(SBIE) TO PIN 1 OF LB (7404). %. JUMPER, PIN 2 OF LB To PIN 3 OF 45.
—(28) HEAT SIN (Saoneaive
a wa AL
- ™ ASSEMBLY, P/LAOOES21-01 NIGHT DRIVER RC.BD
Ce oe
an CRI LED METI24 R2
Q ( { ens QZ. 3 R3
Ro Bak
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING
NEXT ASSY RY AIO
RY
ce '- Ol
INTERPRET THIS DRAWING PER USASIYI45
UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES. on: FRACTIONS = 41/16 LES = a1?) ANGLES SURFACE FINISH x48
pT
USED ON DRAW. 8
CHECKED
DESIGN ENGINEER.
ARON T ENGINEER
DOCUMENT CONTROL INITIALS wad DATE, DESCRIPTION
RELEASED FOR PROD REV. PER ECN 441 REV. PER ECN ISBD DRETG CHECK TEN ie
GND M\ICROFARADS, B
- ALL CAPAAITDRS IN) -SV YAW, 5% , CARBON. LALL RESISTORS IN RMS, NOTES: (UNLESS OTHERWIE GAR)
ALY ATARI INCORPORATED 14600 Winchester Boulevard Los Gatos, California 95030
ATARI
Sate NOE] SHEET, ) ‘OF \
Job Title RACETRAK STEERING PCB ASSY Pwe-PYL 000607
a {h sheet 1 of 1
Drawn
Checked Mech. Eng. Proj. Eng. Elec. Eng.
ATARI [Rev. Description Apprv. Description
| H | Redesigned | 5-6-74 |
J Rev per ECN 397 5/|/28/74 K Rev_per ECN'457 6/3/74 L_|Rev per ECN 601 7/15/74 M Rev per ECN 1531
| Item | Part. No. | Qty. | Description |
a
| 1 | 000614 | 1 | Printed Cipcuit Board (E) |
| 2 | 001092 | 1 | Light loun |
| 3 | 001151 | Ref | Schematic Piagram |
| 4 | 11750/10-5750 | 2 | Reslistgr, Comp., 75 ohm, % watt, 5% |
| 5 | 11471/10- 5471 | 4 | Reslistor, Comp, 470 ohm, % watt, 5% |
| 6 | 11332/10-5332 | 2 | Resistor, Comp, 3.3Kohm, \ watt, 5% |
| 7 | 34104 /27-101103 | 2 | Capacitor,| Ceramic, .Oluf | |
| 8 | 70006/38-2N5777 | 2 | Transistor), 2N 5777 (Photo Darlington) |
| 9 | 70000/34-2N3643 | 2 | Transigtor), 2N 3643 |
| 10 | 71008 /38-ME7124 | 2 | Light Emitting Diode, I.R. ME 7124 |
12 |
| 14 | 80089 /79-58905 | 1 | Connector,| 10 pin, PC Mount, Amp #1-380991 |
| 15 | 72-12128 | 1 | Scyew, |Machine, Pan Head Phil, #2-56 x 3/4 Lg. |
| 16 | 75-042 | 1 | Wagher slic Lock #2 |
| 17 | 75-9128 | 1 | Nut, Hex, #2~56 |
| 18 | 003749 | 1 | Retainer, Led Light Mount |
MODIF, 2
= =
MODIF. £ REFER TO SCHEMATIC COIIS! MODIFICATIONS | FOR, COOGI4A REV J P.C. BOARDS
1, BUMPER FROM PIN 2 TO PIN IO OF THE IO PIN CONNECTOR,
ON CiecuIT SIDE OF BOseD,
- JUMPER FROM PIN, 1 OF THE IO PIN CONNECTOR To THE PAD MARKED +5 (END OF eI) ON Ci@cuITt S1Ce OF BOALD, MODIFICATIONS ‘ FOR COCSIA REV K P.C.BOARDS. }, BUMPER FROM PIN Z TO PIN IO OF THE IO PIN CONNECTOR,
ON CIRCUIT S\iDe OF BOARD.
ATARI INCORPORATED
14600 Winchester Boulevard
ATARI Los Gatos, California 95030
MS BMSSEMBUY STEERILG BoARD
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
OR “TWO SHORTING pe | PLOCK SHOWN et
ha ~4+4
- Te
w ACW INPUT Bk
H
\ ! a —*
| Wghes | x | i | 7 |
| Br Ih
| pg xe) | | |S 4 | ; | /E- |
| rep] | w/GN | soe op eo | 1 $203} |
| aa | 23 9% 79 Oe, | 315) 2) | il |
~ > ~= NITOR te TRACK, seecr | me ~ gpro } or onl wie | Wwowe | exer: | | BLACK FLUORESCENT L-_-|---4 LIGHT LIGHT
- ENB
STEERING
5, 25 2, °2. Ya Je. !
t I ! )
I on 4,
NIGHT DRIVER HARNESS SCHEMATIC
Ip "506543-01 eee Ce
coho §» 2, Se eoaeconmcion TA
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.