PC10 Countertop Operation Manual (PCK-CT-US)
PlayChoice Countertop (Nintendo, 1989) · Manual · 26 pages · 11 sections · original scan
Nintendo
OPERATION MANUAL
©1989 Nintendo'of America Inc.
IV.
Vi.
Vil. TABLE OF CONTENTS
LOCATION SET UP .... - 1
A. Game Installation ............... . 1 B. Power On/Off Switch ................00005 - 1 C. Bookkeeping and Self-Test/Option Switch Settings . (Insert)
ADJUSTMENTS ..... sees 2
A. PC Board Adjustments ~ 2 B. Volume Control/Service Switch ... +. 2 C. Monitor Adjustments ........ 0.060. c ccc e cece cece cee eet eee e nets 2
MAINTENANCE AND REPAIR ...... 00-0 eee e eee cence eens rey fees cevenee 3
A. Fuse Replacements ........0. 000s cece cece cee tenet e eee e enn e ne een eens 3 B. Cleaning 3 C. Control Panel . 3 D. Front Screen Removal .. . -4 E, Video Monitor Removal . . 4 F.. Game PCB Removal ........... 0.0 cece cece etc e eee entree nee ene teen eens 5
RADIO FREQUENCY INTERFERENCE ..........00 000 eeeeeeeeeee sence rene rene 6
WIRING DIAGRAM ...........00006 oe 68 Ree ERs HERVE so CaS Na See ETE (Insert)
FCC PCB — PCKCT ............44- DOO e es ence eeenenenaecereenceserees (Insert)
REORDER PARTS LIST 2.0.2... eee eee cece cece ener eee e eee e nee e ene eeenes ~ 7 A. Body Parts B. Control Panel .. C. Wiring Harnesses 2.2.0... cece cece teeter eet ene e ete e teens 13, D. Monitor Parts 2.0.6... 6c cece cece rene ete tenet n ete n nee eee 14 E. Main,PE Board Parts: ce .0. vecvers newness ceaete rete an seen eapent eee wiie 15-17 Fo FCC Board Parts ....... 0... c cece cece eet e teen enn etn e nent eens 18
I. LOCATION SET UP
The PlayChoice Countertop is shipped ready for operation. Please check the following to insure proper operation:
- Check the exterior of the game for shipping damage, dents, chips or broken parts.
- Make sure the swivel base operates.
- Unlock the front control panel and rear service door and inspect the interior of the game.
- Remove the plug-in connectors from the FCC board and unsnap the six (6) snap fasteners. (See. Fig. 2.) Pull out slowly until main PC board is clear of cage. Make sure all plug-in game boards are firmly connected. Slide main PC board and FCC cover back into place (make sure the edges of the PC board are in the card guide channels). Snap the six (6) snap fasteners and reconnect all the connectors.
A. Game Installation Requirements AC Power: 120V Grounded Outlet Only Amperage: 1.2 Amps Temperature: 0 to 38 degrees Celsius (32 to 100 degrees Fahrenheit)
Humidity: 95% Relative Maximum Requirement: 34” Maximum Swing Diameter
Countertop Space
Height: 21"
IF YOU HAVE ANY QUESTIONS, PLEASE CALL NINTENDO SERVICE AT: 1-800-633-3236
B. Power On/Off Switch A Power On/Off Switch is located in the rear of the game, in the bottom left corner of the cabinet.
USE ONLY A GROUNDED OUTLET FOR THIS GAME. FAILURE TO DO SO MAY RESULT IN DESTRUCTION OF ELECTRIC COMPONENTS.
I. ADJUSTMENTS
Red Gain FIG 2. PC BOARD ADJUSTMENTS
Green Gain Blue Gain
Service Switch Speaker Volume
Focus Screen H. Pos. H. Hold V. Pos. V. Size V. Hold Bright Contrast FIG 3. MONITOR ADJUSTMENTS
II, MAINTENANCE AND REPAIR
A. Fuse Replacements This game contains two fuses. Replace only with the same type as listed:
Main Fuse 4A 250V (on Switch Plate) Video Monitor Fuse 1.5A 125V Slow Blow
B. Cleaning The exterior of the game and all metal parts can be cleaned with a nonabrasive cleanser. Use only a soft cloth and a plastic cleaner for cleaning the plastic front screen.
C. Control Panel and Coin Mechanism
Unlock the control panel by turning the key to the right and swinging the panel forward. (See Fig. 4.) The coin mechanism can now be removed for repair or adjustment. Reach under the coin mechanism bracket and loosen the wing nut. Pull out and down. The coin mechanism wires must be disconnected before total removal is possible. Reverse the procedure for re-assembly.
D. Front Screen Removal
After opening the control panel, reach under the front screen just to the left of center using the finger hole. Pull forward to remove or replace the front screen. (See Fig. 4.)
Fig. 4
E. Video Monitor Removal
If you need to remove the video monitor, follow the instructions listed below. However, the following procedure should only be performed by an experienced Service Technician:
IT lS RECOMMENDED THAT THE GAME BE LEFT UNPLUGGED FOR AT LEAST ONE HOUR BEFORE REMOVING THE VIDEO MONITOR. THIS WILL PROBABLY DISCHARGE THE CRT, BUT EXTREME CAUTION IS STILL NECESSARY.
Video Monitor Removal — Continued
- Make sure the game is unplugged.
- Unlock and remove the back door and unplug all the harnesses and cables from the video monitor.
- Standing at the front opening of the game, carefully remove the cardboard bezel attached at the corners with velcro. (See Fig. 6.) 4, Remove the four (4) mounting machine screws and disconnect the coin-timer PC board.
- Carefully pull the video monitor straight out toward you.
USE EXTREME CAUTION AND DO NOT TOUCH ELECTRICAL PARTS OF THE YOKE AREA WITH YOUR HANDS OR WITH ANY METAL OBJECT IN YOUR HANDS.
F. Game PCB Removal . Make sure the game is unplugged! . Open the back door. . Remove all the plug-in type connectors from the FCC board. . Pull out the six (6) snap fasteners on the perimeter of the cover. (See Fig. 2.) . Slowly pull the FCC board and main PC board out of the FCC cage. . Carefully pull the FCC board off the main board edge connectors or lay flat on a table as shown in Fig. 5 below. Qu pwn sa
- Reverse the procedure exactly to reinstall.
0 ‘ 0 tt ANNU
Fig. 5
IV. RADIO FREQUENCY INTERFERENCE In order to protect against RFI radiated from this equipment, please comply with the following:
- Do not use non-Nintendo parts. ¢ Do not modify your game circuitry.
- Do not modify the wiring harness and connections.
- Connect this game only to a grounded 3-wire outlet. ¢ After servicing the game PCB, shut the shield cover completely with the snap fasteners. (See Fig. 2.)
PC BOARD
DEBESBESEEBEReos EEBEBERBEROLERSERee U eB
C BOARD
or) feof] eh
40] 40 [LEFT (4) He 4522 gESCESEE
LED PCB
PCK1-LED POWER SUPPLY
yyy Wy ayy
ISOLATION TRANSFORMER
POWER CORD
AC4120V
GREEN
COIN MECH. SPEAKER 4P + Ta oo rt ite = 4j4 pa Lo
OPERATION PANEL
WHITE
BLACK
eP afro}
MAIN PCB
D By COLOR MONITOR
GND WIRING DIAGRAM = 01/43/89 = a 4 SHIAK
PCK COUNTER TOP
Nintendo of America Inc. p
Ls
C18=- char cear- cas, cae x Ga 403 | 108 a
103 | 102 c7 ce=-co Camron ciep cis-csey cts ciey-cs 103 | es | 63 | 63 | es C4 S202 >= 3 == C405 06 it co =
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
VII. REORDER PARTS LIST
BODY PARTS — FRONT VIEW (FIG. 6)
ITEM NO. PART NUMBER
1 PCKCT-01-01 2 PCKCT-01-02 3 PCKCT-01-03 4 PCKCT-01-04 5 PCKCT-01-05 6 PCKCT-01-06 7 PCKCT-01-07 8 PCKCT-01-08 9 PCKCT-01-09 10 PCKCT-01-10 1 PCKCT-01-11 12 PCKCT-01-12 13 PCKCT-01-13 14 PCKCT-01-14 15 PCKCT-01-15 16 PCKCT-01-16 17 PCKCT-01-17 18 PCKCT-01-18 19 PCKCT-01-19 20 PCKCT-01-20 21 PCKCT-01-21 22 PCKCT-01-22 ORDER NO.
8479 8480 8481 8482 8483 8484 8485 8486 8487 8488 8489 8490 8491 8492 8493 8494 8495 8496 8497 8498 8499 8500 DESCRIPTION
Cabinet, (PCKCT) Bracket, Front Screen (PCKCT) Speaker, SS403 (PCKCT) Power Supply, SPL-50-3200 Bracket, Power Supply (PCKCT) Cover, Power Supply Bracket (PCKCT) Lock Catch, Control Panel (PCKCT) Game Counter, 6-Y-41611-401-SE Coin Slot, 25 cents (PCKCT) Bezel, Coin Slot (PCKCT) Bracket, Coin Mech. (PCKCT) Bezel, Coin Return (PCKCT) Coin Mech, 11-4040-09 Control Panel Assy. (PCKCT) Grill, Speaker (PCKCT) Screen, Front (PCKCT) Bezel, Monitor (PCKCT) PCB, PCK1-LED Complete Assy (PCKCT) Bracket, LED PCB (PCKCT) Monitor, 13” Y19G7803 Picture Tube, (PCKCT) Manual, Operation (PCKCT)
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
BODY PARTS — REAR VIEW (FIG. 7)
ITEM NO.
OMBNOORWN= PART NUMBER
PCKCT-01-23 PCKCT-01-24 PCKCT-01-25 PCKCT-01-26 PCKCT-01-27 PCKCT-01-28 PCKCT-01-29 PCKCT-01-30 PCKCT-01-31 PCKCT-01-32 PCKCT-01-33 PCKCT-01-34 TKGU-01-03 TMAU-11-14. PCKCT-01-35 TMAU-14-12 PCKCT-01-36 PCKCT-01-37 PCKCT-01-38 PCKCT-01-39 PCKCT-01-40 PCKCT-01-41 ORDER NO.
8501 8502 8503 8504 8505 8506 8507 8508 8509 8510 8511 8512
8513
8514 8515 8516 8517 8518 8519 DESCRIPTION
Fan, DFA0812L Assy Bracket, Fan (PCKCT) Nut, 6-23 Kep (PCKCT) Power Switch Assy (PCKCT) Switch, Power XR-210K-ON-OFF Bracket, Power Switch (PCKCT) Cord, Power Assy (PCKCT) Bushing, Strain Relief SR 6P3-4 Cage, FCC (PCKCT) PCB, PCK1-CPU Complete Assy PCB, PCK-CT-FCC Complete Assy Door, Back (PCKCT) Lock, K6510 Cam, B31R Door, Cash (PCKCT) Lock, Cash Door Retainer, Door (PCKCT) Box, Cash (PCKCT) Transformer, 3P87 Lock Catch, Cash Door (PCKCT) Fuse, 4A 250v Fuse, 1.5A SB 125v
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
CONTROL PANEL ASSEMBLY (FIG. 8)
DESCRIPTION ITEM NO. PART NUMBER ORDER NO.
| 1 | PCKCT-23-01 | 8521 |
| 2 | PCKCT-23-02 | 8522 |
| 3 | PCKCT-23-03 | 8523 |
| 4 | PCKCT-23-04 | 8524 |
| 5 | MDSA-23-29 | 933 |
| 6 | MDSA-23-30 | 934 |
| 7 | MDSA-23-31 | 935 |
| 8 | TKGU-01-03 | 632 |
| 9 | TMAU-11-14 | 639 |
| 10 | PCKCT-23-05 | 8525 |
| 1 | PCKCT-23-06 | 8526 |
| 12 | PCKCT-23-07 | 8527 |
| 13 | PCKCT-23-08 | 8528 |
Base, Control Panel w/overlay (PCKCT) Overlay, Control Panel (PCKCT) Joy Stick, SWSTK Hinge, 87942-1088 Collar, Switch P163 Bezel, Switch P163 Switch, P163CWAG Red Lock, #K6510 Cam, B31R Button Assy, 53-9200-16 Black Button Assy, 53-9200-10 Red Sponge, 19.7 x 0.5 x 0.5 Black w/Ad Nut, 8-32 Kep
FIG. 8
WIRING HARNESSES
PART NUMBER
PCKCT-41-01 PCKCT-41-02 PCKCT-41-03 PCKCT-41-04 PCKCT-41-05 PCKCT-41-06 PCKCT-41-07 PCKCT-41-08 PCKCT-41-09 PCKCT-41-10 PCKCT-41-11 PCKCT-41-12 PCKCT-41-13 PCKCT-41-14 PCKCT-41-15 ORDER NO.
8530 8531 8532 8533 8534 8535 8536 8537 8538 8539 8540 8541 8542 8543 8544 DESCRIPTION
Harness, Control 24P (PCKCT) Harness, Joystick 6P (PCKCT) Harness, Power 10P (PCKCT) Harness, Video 6P (PCKCT) Harness, Counter/Coin 8P (PCKCT) Harness, LED 12P (PCKCT) Harness, Speaker 2P (PCKCT) Harness, Coin 4P (PCKCT) Harness, Monitor 2P (PCKCT) Harness, Power Supply 3P (PCKCT) Harness, Transformer (PCKCT) Harness, Fan 3P (PCKCT) Wire, Fuse Black (PCKCT) Wire, Power Switch White (PCKCT) Wire, Power Switch Black (PCKCT)
MONITOR PARTS
PART NUMBER ORDER NO. DESCRIPTION
| MON-20-01 | 8558 | IC, Regulator STR 3123 |
| MON-20-02 | 8559 | IC, Video UPC 1397 NEC |
| MON-20-03 | 8560 | IC, Horiz Vert LA7823 |
| MON-20-04 | 8561 | IC, Vert Output UPC 1378 |
| MON-21-01 | 8562 | Diode, D1 Fast SW RU-2 |
| MON-21-02 | 8563 | Diode, SI 1A 600v |
| MON-21-03 | 8564 | Diode, GFE 10R |
| MON-22-01 | 8565 | Transistor, NPN CC |
| MON-22-02 | 8566 | Transistor, 2SD1398 |
| MON-22-03 | 8567 | Transistor, 2SC2068 |
| MON-23-01 | 8568 | Coil, Width — TODAI |
| MON-23-02 | 8569 | Coil, Lin — TODAI |
| MON-24-01 | 8570 | Transformer, Flyback |
| MON-24-02 | 8571 | Transformer, Horiz Driver |
| MON-25-01 | 8572 | Res, Variable 2K ohm |
| MON-25-02 | 8573 | Res, Variable 10K ohm |
| MON-25-03 | 8574 | Res, Variable 200 ohm |
| MON-25-04 | 8575 | Res, Variable 200K ohm |
| MON-25-05 | 8576 | Res, Variable 500 ohm |
| MON-25-06 | 8577 | Res, Trim Pot 2K ohm 0.3w |
| MON-25-07 | 8578 | Res, Trim Pot 200 ohm |
| MON-26-01 | 8579 | Cap, Electrolytic 1.0 UF 50v |
| MON-26-02 | 8580 | Cap, Electrolytic 10 UF 25v |
| MON-26-03 | 8581 | Cap, Electrolytic 22 UF 160v |
| MON-26-04 | 8582 | Cap, Electrolytic 47 UF 25v |
| MON-26-05 | 8583 | Cap, Electrolytic 470 UF 16v |
| MON-26-06 | 8584 | Cap, Electrolytic 1000 UF 16v |
| MON-26-07 | 8585 | Cap, Electrolytic 1000 UF 25v |
| MON-26-08 | 8586 | Cap, PolyPro PP6100 2% 1500v |
| MON-26-09 | 8587 | Cap, PolyPro .39 UF 5% 200v |
| MON-26-10 | 8588 | Cap, .1 20% 125v AC |
| MON-26-114 | 8589 | Cap, Disc .0015 10% 500v |
| MON-26-12 | 8590 | Cap, Disc .0022 10% 500v |
| MON-27-01 | 8591 | Res, M. Oxide 3.9K 5% |
| MON-27-02 | 8592 | Res, 2.7 ohm 5% 7w |
| MON-27-03 | 8593 | Res, Thermister |
| MON-28-01 | 8594 | Fuse, 1.5A |
| MON-29-01 | 8595 | Plug, 2 Pin |
| MON-29-02 | 8596 | Plug, 4 Pin |
MAIN PC BOARD — PLAYCHOICE
PARTNUMBER ORDERNO. DESCRIPTION (Reference Designations and Locations)
| PCKU-21-01 | 7929 | PCK1 CPU Complete PCB Assembly | |
| PCHU-21-11 | 946 | Z80A Microprocessor | (6X) |
| PCHU-21-12 | 945 | RP2A03E Microprocessor | (1H) |
| PCHU-21-13 | 4460 | RP2CO3B PPU | (3H) |
| PCKU-21-14 | 7936 | 27128 16K-Byte EP-ROM 300ns PCK 1-C-8T | (8T) |
| PCKU-21-15 | 7937 | 2764 8K-Byte EP-ROM 300ns PCK 1-C-8K | (8K) |
| PCKU-21-16 | 7938 | 2764 8K-Byte EP-ROM 300ns PCK 1-C-8M | (8M) |
| PCKU-21-17 | 7939 | 2764 8K-Byte EP-ROM 300ns PCK 1-C-8P | (8P) |
| PCHU-21-18 | 2060 | TMM2115BP-15 2K-Byte RAM 150ns | (2k) |
| PCHU-21-19 | 2061 | HM6116 ASP-20 2K-Byte RAM 200ns | (4K, 8R, 8V) |
| PCHU-21-20 | 4811 | TC5517 CPL-20 2K-Byte C-MOS RAM 200ns | (8W) |
| PCKU-21-21 | 7940 | N82SI29N 256 x 4-Bit Bipolar ROM PCK1-C-6D | (6D) |
| PCKU-21-22 | 7941 | N82SI29N 256 x 4-Bit Bipolar ROM PCK1-C-6E | (6E) |
| PCKU-21-23 | 7942 | N82SI29N 256 x 4-Bit Bipolar ROM PCK1-C-6F | (6F) |
| PCHU-21-24 | 2189 | 74LS00 Quad 2-Input NAND | (5H, 8J, 6U) |
| PCHU-21-25 | 2190 | 74LS02 Quad 2-Input NOR | (4U) |
| PCHU-21-26 | 2191 | 74LS04 Hex Inverters | (8D, 3G, 8G, 5u, 7R, 7Y, 4Z) |
| PCHU-21-27 | 2193 | 74LS08 Quad 2-Input AND | (7X) |
| PCHU-21-28 | 2195 | 74L811 Triple 3-Input AND | (5P) |
| PCHU-21-29 | 2196 | 74LS14 Hex Schmitt Inverters | (4v) |
| PCHU-21-30 | 2202 | 74LS32 Quad 2-Input OR | (7C, 5T) |
| PCHU-21-31 | 2203 | 74LS42 4 To 10 Decoders | (47) |
| PCHU-21-32 | 2204 | 74LS55 2-Wide 4-Input AND-OR-INVERT Gates | (5K) |
| PCHU-21-33 | 2205 | 74LS74A Dual “‘D” Flip-Flops (P, CL) | (7J, 7K, 5M) |
| TPP2-06-20 | 2208 | 74LS86 Quad 2 Input EX-OR | (4M) |
| PCHU-21-34 | 2210 | 74LS109A Dual J-K Flip-Flops (PLE, CL) | (4Y) |
| PCHU-21-35 | 2216 | 74LS139 Dual 2 To 4 Decoders | (7H, 2L, 6T) |
| PCHU-21-36 | 2220 | 74LS157 Quad 2 To 1 Data Selectors | (7S, 7T, 7U, 7V) |
| PCHU-21-37 | 2223 | 74LS161A 4-Bit Binary Counters | (6H, 6J, 6K, 6L, 6M, 4R) |
| PCHU-21-38 | 2225 | 74LS164 8-Bit Shift Registers | (8H, 5Q) |
| PCHU-21-39 | 2226 | 74LS165A 8-Bit Shift Registers | (8B, 8C, 7F) |
| PCHU-21-40 | 2228 | 74LS175 Quad “D” Flip-Flops (CL) | (4S) |
| PCHU-21-41 | 2229 | 74LS194A 4-Bit Shift Registers | (6Q, 6R) |
| PCHU-21-42 | 2230 | 74LS240 Octal Bus Inverters (TS) | (5A, 6A, 7B) |
| PCHU-21-43 | 2232 | 74LS244 Octal Buffers & Line Drivers (TS) | (6B, 1L, 2M, 3M, 8S, 5V, 6V) |
| PCHU-21-44 | 2233 | 74LS245 Octal Bus Transceivers (TS) | (1K, 6Z) |
| PCHU-21-45 | 2235 | 74LS259 8-Bit Addressable Latches | (7D, 7E) |
| PCHU-21-46 | 2239 | 74LS299 8-Bit Shift/Storage Registers | (7L, 7N, 7Q) |
| PCHU-21-47 | 2242 | 74LS367A Hex Bus Drivers | (4L) |
| PCHU-21-48 | 2243 | 74LS368A Hex Bus Drivers | (8E, 8F, 5S) |
| PCHU-21-50 | 2247 | 74LS377 Octal “D” Flip-Flops | (6P) |
| PCHU-21-51 | 2267 | 74804 Hex Inverters | (2G, 6N) |
| PCHU-21-52 | 2259 | 7437 Quad-2-Input NAND Buffers | (4X) |
| PCHU-21-53 | 2278 | 75471 Dual Peripheral AND Drivers | (6C) |
| PCHU-21-54 | 4812 | 74HC10 Triple 3-Input NAND C-MOS | (8Y) |
| PCKU-21-55 | 8004 | TC74HC373 Octal 3-State D-Latches C-MOS | (8K) |
| PCKU-21-55 | 1143 | PST518A Low Voltage Detector | (72) |
| PCHU-21-56 | 1445, | LM324 Quad Operational Amplifiers | (3E) |
| PCHU-21-57 | 1443 | LM3900 Quad Operational Amplifiers | (1E) |
MAIN PC BOARD (CONTINUED)
PARTNUMBER ORDERNO. DESCRIPTION (Reference Designations and Locations)
| PCKU-21-57 | 7943 | TC 4053BP Triple 2-Channel Multiplexer C-MOS | (5C) |
| PCHU-21-58 | 735 | CD 406 6B Quad Analog Switches C-MOS | (3C) |
| PCHU-21-59 | 2178 | 2SA933 Silicon PNP Transistor | (Q11, Q12, Q14, Q15, Q17, |
Q18)
| PCHU-21-60 | 2179 | 2SA1015 Silicon PNP Transistor | (Q3, Q5, Q7, Q20) |
| PCHU-21-61 | 2184 | 2SC1740 Silicon NPN Transistor | (Q8VQ10, Q13, Q16, Q19, |
Q20~Q26)
| PCHU-21-62 | 2185 | 28C1815 Silicon NPN Transistor | (Q1, Q2, Q4, Q6) |
| PCHU-21-63 | 1003 | ES1F Diode | (D1) |
| PCHU-21-64 | 1012 | 185277B Diode | (D3, D4) |
| PCHU-21-65 | 4813 | EG01Y Diode | (D2) |
| PCHU-21-66 | 1002 | DAN401 Quad Cathode-Common Diode Array | (DA1~DA8) |
| PCHU-21-67 | 4817 | 1.0f 5.5V Electric Double Layer Capacitor (EEC F5R 5U105) | (C3) |
| PCHU-21-68 | 680 | 68pf 50V Ceramic-Disc Capacitor | (D44) |
| PCHU-21-69 | 663 | 100pf SOV Ceramic-Disc Capacitor | (C35, C36, C46, C71) |
| PCHU-21-70 | 669 | (C11, C39) | |
| PCHU-21-71 | 675 | 330pf 50V Ceramic-Disc Capacitor | (C2, C6, C40, C41) |
| PCKU-21-71 | 7945 | 470pf 50V Ceramic-Disc Capacitor | (C12) |
| PCHU-21-72 | 664 | 1000pf 50V Ceramic-Disc Capacitor | (C5) |
| PCHU-21-73 | 665 | 0.01uf 50V Ceramic-Disc Capacitor | (C4, C22, C38, C43, |
C80~C83, C86~C89, C91, C92, C94~~C101, C1038~C108, CC110C120, C122C126, C128, C130~C144, C146, C148~C156, C158~C163, C165~C187)
| PCHU-21-74 | 4815 | 0.047uf 50V Ceramic-Disc Capacitor | (C15~C17) |
| PCHU-21-75 | 655 | 0.2uf 12V Ceramic-Disc Capacitor | (C21) |
| PCHU-21-76 | 716 | 0.047uf 50V Film Capacitor | (C33, C34) |
| PCHU-21-77 | 685 | uf 16V Al Electrolytic Radial Cap. | (C7, C8) |
| PCHU-21-78 | 689 | 3.3uf 16V Al Electrolytic Radial Cap. | (C13, C14, C25, C28, C31, |
C32)
| PCHU-21-79 | 683 | 10uf 16V Al Electrolytic Radial Cap. | (C23, C24, C26, C27, C29, |
C30, C37, C42)
| PCHU-21-80 | 688 | 33uf 16V Al Electrolytic Axial Cap. | (C9) |
| PCHU-21-81 | 4818 | 47uf 16V Al Electrolytic Radial Cap. | (C47~C50) |
| PCHU-21-82 | 684 | 100uf 16V Al Electrolytic Axial Cap. | (C46) |
| PCHU-21-83 | 4819 | 100uf 25V Al Electrolytic Axial Cap. | (C70) |
| PCHU-21-84 | 687 | 220uf 16V Al Electrolytic Axial Cap. | (C1) |
| PCHU-21-85 | 691 | 470uf 16V Al Electrolytic Axial Cap. | (C20) |
| PCHU-21-86 | 4820 | 3.3uf 16V Tantalum Electrolytic Cap. | (C85, C90, C93, C102, C109, |
C121, C127, C145, C157)
| PCHU-21-87 | 2075 | 0 Ohm Shunt Lead | (R99) |
| PCHU-21-88 | 2076 | 10 Ohm 1/4W + 5% Resistor | (R7) |
| PCHU-21-89 | 2120 | 33 Ohm 1/4W + 5% Resistor | (R32, R37) |
| PCHU-21-90 | 2137 | 51 Ohm 1/4W + 5% Resistor | (R8, R19, R23, R27, R31) |
| PCHU-21-91 | 2077 | 100 Ohm 1/4W + 5% Resistor | (R17, R68, R69, R73) |
| PCHU-21-92 | 2082 | 110 Ohm 1/4W + 5% Resistor | (R3) |
| PCHU-21-93 | 2121 | 330 Ohm 1/4W + 5% Resistor | (R13, R14, R18, R21, R25, |
R29, R36, R90, R91, R97, R93, R110, R111, R112)
| PCHU-21-94 | 2138 | 510 Ohm 1/4W + 5% Resistor | (R46, R56, R66) |
| PCHU-21-95 | 2155 | 820 Ohm 1/4W + 5% Resistor | (R1, R2) |
| PCHU-21-96 | 2078 | 1K Ohm 1/4W + 5% Resistor | (R94~VR96, R120~R131) |
| PCHU-21-97 | 2099 | 2K Ohm 1/4W + 5% Resistor | (R15, R87, R109) |
| PCHU-21-98 | 2105 | 2.2K Ohm 1/4W + 5% Resistor | (R35, R40, R42, R50, R45, |
R52, R55, R60, R62, R65)
| PCHU-21-99 | 2134 | 4.7K Ohm 1/4W + 5% Resistor | (R43, R53, R63) |
| PCHU-21-100 | 2139 | 5.1K Ohm 1/4W + 5% Resistor | (R4, R5, R22, R26, R30, R88, |
R89)
| PCHU-21-101 | 2152 | 7.5K Ohm 1/4W + 5% Resistor | (R16) |
MAIN PC BOARD (CONTINUED)
PART NUMBER ORDER NO.
PCHU-21-102
PCHU-21-103 PCHU-21-104
PCHU-21-105 PCHU-21-106 PCHU-21-107 PCHU-21-108 PCHU-21-109 PCHU-21-110 PCHU-21-111 PCHU-21-112 PCHU-21-113 PCHU-21-114
PCHU-21-115 PCHU-21-116 PCHU-21-117 PCHU-21-118 PCHU-21-119 PCHU-21-121 PCHU-21-123 PCHU-21-124 PCHU-21-125 PCHU-21-126 PCHU-21-127 PCHU-21-129 PCHU-21-130 2079
2086 2100
2080 2101 2126 DESCRIPTION (Reference Designations and Locations) 10K Ohm 1/4W + 5% Resistor (R12, R34, R38, R41, R44, R51, R54, R61, R64, R74, R82, R83, R92, R93, R100~R102, R104, R106, R108) 12K Ohm 1/4W +5% Resistor 20K Ohm 1/4W + 5% Resistor
100K Ohm 1/4W + 5% Resistor 200K Ohm 1/4W + 5% Resistor 360K Ohm 1/4W + 5% Resistor 750K Ohm 1/4W + 5% Resistor 1M Ohm 1/4W +5% Resistor 1.8M Ohm 1/4W + 5% Resistor 2.2M Ohm 1/4W + 5% Resistor Hex 5.1K Ohm Series Resistor Array Octal 1K Ohm Series Resistor Array Quad 68 Ohm Parallel Resistor Array
NT-01 Resistor Array 500 Ohm Variable Resistor, Red Cap 500 Ohm Variable Resistor, Green Cap 500 Ohm Variable Resistor, Blue Cap 8MHZ Crystal 21.47727MHZ Crystal 8-Station, Single-Throw, DIP Bit Switch MINI-BIT Header 16 Pin DIP IC Socket 28 Pin DIP IC Socket 40 Pin DIP IC Socket 96 Pin DIN Connector Receptacle GL-3HD1 Visible Light Emitting Diode (R71) (R6, R39, R70, R72, R103, R105, R107) (R33, R75) (R9~R11) (R79) (R78, R80, R84) (R76, R85) (R81) (R77, R86) (RM1, RM16) (RM5, RM8‘VAM10, AM13) (RM6, RM7, RM11, RM12, RM14, RM15) (RM2~RM4) (vR1) (vR2) (VR3) (x1) (x2, X3) (Swi, Sw) (sw) (S688) (S2V$5) (S1, $9, $10) (CH1\CH10) (LED1)
FCC PC BOARD
PART NUMBER
PCKCT-24-01 PCKCT-24-02 MDST-31-02 PCKCT-24-03 PCKCT-24-04 MON-61-02 MON-13-00 PCKCT-24-05 PCKCT-24-06 PCKCT-24-07 ORDER NO.
PCKCT-24-08 MDSU-08-42 TKG-15-16 TRS-07-69 CHPU-21-68 DESCRIPTION
Conn, Edge 44 pin Conn, Edge 36 pin IC, Audio Amp MB3730 VRES, 1K Ohm Switch, SPST Mom. B3F Res, Carbon 56K 1/4w 5% Res, Carbon 1 ohm 1/4w Bead, Ferr. BLO1RN1-AL2 Cap, Epoxy 68pf Cap, Epoxy 0.01mf(103)
Cap, Epoxy 0.001(102) Cap, Mylar 0.1mf(104) Cap, Electro 4.7mf 16v Cap, Electro 22mf 16v Cap, Electro 220mf 16v LOCATION(S)
P1 P2 IC1 VR1 swi R1 R2, R3 FB1-FB12 C2, C3, C4, C5 CO, C1, C6, C7, C9, C11, C13, C15, C16, C17, C19, C21, C24, C25, C26, C27, C28, C29, C30, C41 C8, C10, C12, C14, C18, C20, C22, C23 C35, C38, C39 C33, C34 C36 C31, C32, C37
PRINTED IN U.S.A,