Destroyer TM-106 1st Printing
Destroyer (Atari, version O2) (Atari, 1977) · Technical Manual · 76 pages · 18 sections · original scan
TM-106 1st printing
Operation, Maintenance and Service Manual
Complete with Illustrated Parts Catalog
Seller warrants that its printed circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its television monitors (in games supplied with monitors) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment. None of the Seller's other products or parts thereof are warranted.
If the products described in this manual fail to conform to this warranty, Sellers’ sole liability shall be, at its option, to repair, replace, or credit Buyer’s account for such products which are returned to Seller during said warranty period, provided:
- Seller is promptly notified in writing upon discovery by Buyer that said products are defective;
- Such products are returned prepaid to Sellers’ plant; and
- Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed. and were not caused by accident, misuse, neglect, alteration, improper repair, installation or improper testing.
In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages.
EXCEPT FOR ANY EXPRESS WARRANTY SET FORTH IN A WRITTEN CONTRACT BE- TWEEN SELLER AND BUYER WHICH CONTRACT SUPERSEDES THE TERMS OF THIS ORDER, THIS WARRANTY 1S EXPRESSED IN LIEU OF ALL OTHER WARRANTIES FX- PRESSED OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTA- BILITY AND FITNESS FOR A PARTICULAR PURPOSE, AND OF ALL OTHER OBLIGA- TIONS OR LIABILITIES ON THE SELLER'S PART, AND IT NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR THE SELLER ANY OTHER LIABILITIES IN CONNECTION WITH THE SALE OF PRODUCTS UNDER THIS OR- DER.
This document is and contains confidential trade secret information of Atari, Inc.
This document is loaned under confidential custody for the sole purpose of operation, maintenance or repair of Atari equipment and may not be used by or disclosed to any person for any other purpose whatever, and remains the property of Atari, Inc.
Neither it nor the information it contains may be reproduced, used, or disclosed to persons not having a need to know consistent with the purpose of the loan, without written consent of Atari, Inc.
DESTROVEF Operation, Maintenance and Service Manual
Complete with Illustrated Parts Catalog
TARI INC. 1265 BORREGAS AVENUE RO. BOX 9027 SUNNYVALE, CALIFORNIA 94086 408/745-2000 * TELEX 35-7488
A
ATARI
All rights reserved. Copyright © 1977 by Atari, Inc. No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher.
For permission requests, write:
ATARI INC 1265 BORREGAS AVENUE RO. BOX 9027 SUNNYVALE, CALIFORNIA 94086
Lithographed in the U.S.A.
TABLE OF CONTENTS
1 LOCATION SETUP INTRODUCTION .... GAME INSPECTION .. LOCATION OF SERIAL NUMBER . INSTALLATION REQUIREMENTS . Power Requirements ... Temperature Range . Humidity Range ... Location Space Requirements Type of Power Cord E. INTERLOCK AND POWER ON/OFF SWITCHES . F. SELF-TEST PROCEDURE IN TABLE 7 G. OPERATOR OPTIONS IN TABLE 2 .. H. Soe>
. FOREIGN LANGUAGE TRANSLATION VOLUME CONTROL SAARARARAWKWWA
2 GAME PLAY ATTRACT MODE READY-TO-PLAY MODE .. C. PLAY MODE ...... D. GAME OVER MODE
3 MAINTENANCE AND ADJUSTMENTS CLEANING ‘i COIN MECHANISM . Components On Coin Door Access to Coin Mechanisms Cleaning of Coin Paths Lubrication .......0.06505 Adjustment of Coin Switch Trip Wire . Mechanical Adjustments on Coin Mechanism . General Troubleshooting Hints FUSE REPLACEMENT LAMP REPLACEMENT REMOVING THE CONTROL PANEL . REMOVING THE TV MONITOR =™90
4 THEORY OF OPERATIO. A. GENERAL INFORMATION... 00. 0c ccc cece cere cece eee e nent tenes B. POWER SUPPLIES C. CRYSTAL OSCILLATOR AND TV SYNC COUNTDOWN CHAINS D. E Fr . MICROCOMPUTER ADDRESS MAP ... INPUTIOUTPUT Digital Output Inputs ..
MINOR OBJECT CIRCUIT ... MAJOR OBJECT CIRCUIT ALPHA-NUMERICS ... VIDEO OUTPUT ... WAVE GENERATOR .. AUDIO ..
5 ILLUSTRATED PARTS CATALOG. . PAST ETO
LIST OF ILLUSTRATIONS
Figure 1-1 Location of Serial Number on Game PCB Figure 1-2. Location of Voltage-Changing Plugs on the Power Supply Figure 1-3. Location of Power On/Off and Interlock Switches Figure 14 Location of Volume Adjustment .. Figure 3-1 Coin Door Assembly ...........+ Figure 3-2. Hinging Open the Magnet Gate Assembly Figure 3-3 Removal of Coin Mechanism ...............6 Figure 3-4 Surfaces to Clean Inside the Coin Mechanism Figure 3-5 Removal of Plate Covering Rear of Coin Slot . Figure 3-6 Close-Up View of Lubrication Point . Figure 3-7 Detail View of Coin Switch and Trip Wire rigure 3-8 Securing the Coin Switch Trip Wire ... Figure 3-9 Adjustments on Coin Mechanism ..... Figure 3-10 Removing the Cabinet Light Assembly Figure 3-11 Removal of TV Monitor .........+ Figure 4-1 Destroyer Game Block Diagram Figure 4-2. Destroyer Game PCB Block Diagram .. Figure 4-3 Destroyer Game Harness Diagram .. Figure 4-4 Destroyer Power Supply Schematic ... Figure 4-5 Destroyer Game PCB Schematic Diagram Figure 4-6 TV Monitor Schematics .... Figure 5-1 Destroyer Final Assembly . Figure 5-2. TV Shelf Assembly ... Figure 5-3 Display Light Assembly . Figure 5-4 Coin Door Final Assembly Figure 5-5 Coin Door Assembly Figure 5-6 Power Supply Assembly .. Figure 5-7 RF Shield PCB Assembly .. Figure 5-8 Destroyer Game PCB Assembly Figure 5-9 Control Panel Assembly .. Figure 5-10 Switch Assembly . Figure 5-11 Shift Assembly ...
LIST OF TABLES
Table 1-1 Self-Test Procedure Table 1-2 Option Switch Settings Table 1-3 Language Option Switch Settings
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
LOCATION SETUP
A. INTRODUCTION Atari’s Destroyer ™ is aone player computer controlled game that simulates anti-submarine warfare. The object of the game is to sink as many submarines as possible. A player controls the speed of the destroyer, the time at which the depth charges are released, and the depth at which depth charges explode. Point value of submarines depends on both the speed and the depth at which the submarines travel.
As the owner of Destroyer, you have certain options available in the game. The options include: the number of coins necessary to play the game, how long the game will last, and whether or not extended play is awarded. These options are selected by removing the game printed circuit board from the metal RF box and setting the desired switches.
Figure 1-1 Location of Serial Number on Game PCB
Destroyer, like all recent Atari video games, has a self-test feature that tests approximately 75% of the game’s circuitry. By energizing the self-test feature, you can determine whether the game is operating properly.
B. GAME INSPECTION Your new Destroyer game is manufactured by Atari with the intent of being ready to play right out of the shipping carton. However, we need your cooperation in supplying the last touch of quality control. Therefore, please follow the procedures below to ensure that you are getting the quality of game that you expect from Atari.
- Examine the external parts of the game cabinet for dents, chips, or broken parts. If you have purchased this game as a new unit, make sure that it looks new.
- Unlock and open the rear access door. Examine the inside of the game cabinet for anything that appears broken or out of place.
VOLTAGE-CHANGING PLUG WIRE COLOR
ON/OFF AND INTERLOCK SWITCHES
PRIMARY FUSES C. LOCATION OF SERIAL NUMBER The serial number for Destroyer is located on a metallic label in the upper left-hand corner of the back of the game cabinet. This serial number also appears in the corner (common to both edge connectors) on the back of the PCB inside the game cabinet. See Figure 1-1.
D. INSTALLATION
REQUIREMENTS
Ail special requirements for installing the game are listed as follows:
Power Requirements: Atari ships Destroyer for domestic operation on 110 VAC, rated at approximately 150 watts. The game can be changed to operate at 95 VAC, 205 VAC, or 220 VAC by unplugging the Molex connector plug (see Figure 1-2 for location of plug), and plugging in another Molex connector plug.
SECONDARY FUSES (MAY OR MAY NOT BE INCLUDED IN GAME)
Figure 1-2 Location of Voltage-Changing Plugs on the Power Supply
Temperature Range: Location and storage temperature ranges should be no lower than zero degrees Celsius (32 degrees Fahrenheit), and no higher than 49 degrees Celsius (120 degrees Fahrenheit).
Humidity Range: Relative humidity at the game location or storage area should not exceed 95%.
Location Space Required: Destroyer requires a minimum of 185 centimeters (73 inches) of vertical clearance, a minimum of 75 centimeters (29.5 inches) of width clearance, and 152 centimeters (60 inches) of depth clearance. Depth clearance includes a minimum of 61 centimeters (24 inches) of player space.
Type of Power Cord: Atari has added a strain relief power cord to Destroyer. The advantage of the strain relief cord is that, if tripped over, the cord will break off. Tripping over a non-strain relief cord may result in ripping out the inside of the game.
E. INTERLOCK AND POWER ON/OFE SWITCHES To minimize the hazard of electrical shock while you are working inside the game cabinet, an interlock switch has been installed at the rear access door. This switch removes all power from the game while the access door is open.
To help you conserve energy, a power on/off switch has been installed on the right side of the top panel, near the front of the game cabinet. See Figure 1-3 for location of switches.
Please check for the proper operation of the rear access interlock switch by performing the following:
- Unlock and open the rear access door.
- Plug the AC power cord into a 110-volt source. (If the voltage is less than 100 VAC, make sure that the voltage plug is changed to the black plug.)
- Set the power on/off switch to the on position by flipping the toggle switch toward the front of the game cabinet.
- Close the rear access door. Within approximately thirty seconds the TV monitor should display a picture,
- Slowly open the rear access door until the TV monitor picture disappears. The TV monitor picture should disappear when the rear access door is opened to less than one-inch at the top of the door.
- Close and lock the rear access door. If the results of Step 5 are satisfactory, then the interlock switch is operating properly. If not satisfactory, check to see if the switch is broken from its mounting or stuck in the on position.
F. SELF-TEST PROCEDURE IN TABLE 1-1 Destroyer will test itself and provide data to communicate with you that the game's circuitry and controls are working properly. We suggest that you do the Destroyer self-test procedure each time you empty the coins from the game’s cash box.
There are two tests performed with the self-test switch on. The first test is done completely by the Destroyer computer. In this test, the computer displays the alpha-numeric character set, determines if its memory is ok, and then displays a code for the game time setting. The second test requires you to activate each switch to determine if they are operating properly. A third test is performed with the selftest switch off. In this test, you determine if the depth control and cursor are operating properly. Perform the self-test by following the instructions in Table 1-1.
G. OPERATOR OPTIONS IV TABLE 1-2 At this time, decide what options are best suited for your location of the Destroyer game. The coinage options on Destroyer are free play, 2 games per coin, 1 game per coin, or 2 coins per game. Destroyer also has a time option for a 50-second, a 75-second, a 100-second, or a 125-second game. A free play mode may also be set for demonstration.
Set the options of the game as described in Table 1-2. Refer to Table 1-2 for the location of the option controls.
H. FOREIGN LANGUAGE TRANSLATION Translation of the English language, used on the TV monitor display, is easily accomplished by adding two read-only memories (ROMs). These ROMs provide translation into German, French, and Spanish. After adding these ROMs, the option
Figure 1-3 Location of Power On/Off and Interlock Switches
Table 1-1
Instruction Destroyer Self-Test
Results if Test Passes Results if Test Fails
Unlock and open the coin door. Set self-test slide switch (located inside and to the left of the coin door) to the on position.
Press START pushbutton.
Move DESTROYER SPEED CONTROL from one position to the other and back again.
Press the DEPTH-RELEASE CONTROL.
Trip the left then the right coin acceptor trip wire.
Close contacts of the coin door slam switch. Top displayed line on TV monitor is numeric characters 0 through 9, displayed twice.
Second displayed line on TV monitor is Alphabetic characters A through Z.
Third displayed line on TV monitor is RAM OK ROM OK.
Fourth displayed line on TV monitor is a single digit indicating the setting of the game timer as follows: 0 = 50 second game 75 second game 100 second game 125 second game One or more numeric character is missing.
One or more alphabetic characters is missing.
Third displayed line on TV monitor is BAD RAM and/or BAD ROM.
Sonar ping sound is heard each each time the START pushbutton is pressed.
Sonar ping sound is heard each time the DESTROYER SPEED CONTROL is moved to FAST and each time it is moved to SLOW.
Sonar ping sound is heard each time the DEPTH-RELEASE CONTROL is pressed.
Sonar ping sound is heard each time a coin acceptor trip wire is tripped.
Sonar ping sound is heard each time the slam switch contacts are closed. No sound is heard.
No sound is heard.
No sound is heard.
No sound is heard.
No sound is heard.
3 Set self-test slide switch to off position. Trip one of the coin acceptor trip wires for a game credit. Rotate knob marked ROTATE TO SET DEPTH OF CHARGE fully clockwise, then fully counterclockwise. Dashed horizontal line moves up when knob is rotated in one direction and down when rotated in the other direction. Dashed horizontal line does not move or is not present at all.
Table 1-2 Option Switch Settings
Option Switch Settings Option
| Free Play | ON | ON |
| 2 Plays per Coin | ON | OFF |
| 1 Coin Per Play | OFF | ON |
| 2 Coins Per Play | OFF | OFF |
| 50-Second Game | ON | ON |
| 75-Second Game | ON | OFF |
| 100-Second Game | OFF | ON |
| 125-Second Game | OFF | OFF |
No Extended Play
Extended Play for 1500 points
Extended Play for 2500 points
Extended Play for 3500 points
OPTION SWITCH (LOCATION B8)
switches must be set for the proper language translation. See Table 1-3 for the proper option switch settings.
Table 1-3 Language Option Switch Settings The translation ROMs are available through Atari Customer Service. In your order, please include the serial number of your Destroyer game. Contact Atari Customer Service at the following address:
Ic . , i Atari Customer Service Option Switch Setting 2175 Martin Avenue Language rs |. 6 | Santa Clara, California 95050
| German | OFF | OFF | |
| French | ON | OFF | |
| Spanish | OFF | ON | I. VOLUME CONTROL |
L If volume is incorrect for your location, remove
| English | ON | ON | the game PCB and adjust the volume to your desire. |
See Figure 1-4 for the location of volume control.
Figure 1-4 Location of Volume Adjustment
During game play, Destroyer operates in one of four modes: attract, ready-to-play, play mode, or game over mode.
A. ATTRACT MODE The attract mode begins with the application of power and ends when the proper amount of coins are accepted. During this mode the most recent score appears in the upper left, the high score since power on appears in the upper right. The appropriate coin and extended play messages appear in the middle of the screen, according to the options you have selected. All controls and sounds are inactive during this mode. The submarines and the destroyer appear as in game play.
B. READY-TO-PLAY MODE This mode begins when the proper number of coins are accepted, and ends when the START button is pressed. During this mode, the message PRESS START appears, coin messages disappear, the ships freeze on the screen and the depth control is enabled so that the player is familiar with it before the game starts.
Cc. PLAY MODE This mode begins when the START button is pressed and ends when the game is over. During this mode all controls and sounds are active. The player sets the depth at which charges explode by rotating the DEPTH-RELEASE CONTROL. Depth is indicated on the screen by a dashed horizontal line (called “the cursor’). Depth charges are released by pushing the DEPTH-RELEASE CONTROL. Once the depth charges are released, the depth cannot be reset. In other words, the charges always explode at whatever depth the cursor was set at when the charges were released. A direct hit is not necessary since the shock wave from a near miss will crush the submarine’s hull. The speed of the destroyer may be controlled by the DE- STROYER SPEED CONTROL lever. The control has a SLOW and a FAST position that result in a distinctive change in the rate at which the Destroyer moves across the TV monitor. The engine sound changes accordingly.
When a depth charge explodes without hitting a submarine, a low “boom” sound is heard. When a sub is hit the explosion quality changes to cue the player (along with the explosion scene) that a submarine has been hit. Sonar pings are heard any time explosions aren't active. Points are displayed where the submarine was hit, after each explosion scene.
D. GAME OVER MODE When the game ends, the words GAME OVER appear on the screen for approximately four seconds. Then, if there is credit, the machine enters the readyto-play mode. If there is no credit the machine enters the attract mode.
MAINTENANCE AND ADJUSTMENTS
Due to its solid-state electronic circuitry, this Atari unit should require very little maintenance and only occasional adjustment. Information given in this chapter and elsewhere in this manual is intended to cover most servicing situations that may be encountered at the game site. The procedures given are in sufficient detail to be understood by a person with moderate technical background.
If reading through this manual does not lead to solving a specific maintenance problem, you can reach Atari’s Customer Service Department by telephone Monday through Friday, from 7:30 a.m. to 4 p.m. Pacific Time. From California, Alaska and Hawaii, call (408) 984-1900; from the remaining 47 states call (800) 538-6892 (toll-free).
If you are interested in gaining more information on video game technology, especially the electronics, we recommend reading the Video Game Operator’s Handbook, manual number TM-043. This book is available from Atari, Inc., Attn. Customer Service Department, 2175 Martin Avenue, Santa Clara, CA 95050 for $5 each, or from your distributor.
A. CLEANING The exteriors of game cabinets and plex panels may be cleaned with any non-abrasive household cleaner. If desired, special coin machine cleaners that leave no residue can be obtained from your distributor. Do not dry-wipe the plex panels because any dust can scratch the surface and result in fogging the plastic.
B. COIN MECHANISM Components On Coin Door Figure 3-1 shows the back side of the coin door assembly where the game’s two coin mechanisms are mounted. Included is the lock-out coil assembly; the lock-out wires are connected to this assembly but are hidden behind the coin mechanisms. During the attract mode the microcomputer energizes the lockout coil, causing the lock-out wires to retract far enough to allow genuine coins to reach the coin box. But during the ready-to-play mode when the LED is lit, and during the play mode (and also when AC power to the game has been turned off),the lock-out coil is de-energized, causing the lock-out wires to move out far enough to divert coins over to the return chute.
Slam Switch Assembly
Coin Lock-out Coil LAMP HOLDER
Figure 3-1 Coin Door Assembly Directly below each coin mechanism is a secondary coin chute and a coin switch with a trip wire extending out to the front edge of the chute. When the trip wire is positioned correctly, a coin passing down the secondary chute and into the coin box will momentarily push the trip wire down and cause the switch contacts to close.
Also shown in the photograph is a slam switch assembly. It has been included to discourage any players who might try to obtain free game plays by violently pounding on the coin door to momentarily close the contacts on a coin switch. The slam switch contacts connect to the microcomputer system, which will ignore coin switch signals whenever the slam switch contacts are closed.
Access to Coin Mechanisms To remove jammed coins, and for maintenance cleaning, each magnet gate assembly can be hinged open without removing it from the door, as shown in Figure 3-2. Or, if necessary, each coin mechanism can be entirely removed from the door merely by pushing down onarelease lever and simultaneously tilting the mechanism back, then lifting it up and out. This is shown in Figure 3-3.
Figure 3-2. Hinging Open the Magnet Gate Assembly
Figure 3-3 Removal of Coin Mechanism
Cleaning of Coin Paths
By talking to many operators, we have found that the best method of cleaning a coin mechanism is by using hot or boiling water and a mild detergent. A toothbrush may be used for those stubborn buildups of residue. After cleaning, flush thoroughly with hot or boiling water, then blow out all water with compressed air.
Figure 3-4 shows the surfaces to clean inside the coin
(Clean both surfaces where coin enters the mechanism, as well as the magnet) Figure 3-4 Surfaces to Clean Inside the Coin Mechanism mechanism. These include the inside surface of the mainplate, and the corresponding surface of the gate assembly. There may also be metal particles clinging to the magnet itself. To remove these you can guide the point of a screwdriver or similar tool along the edge of the magnet.
If coins are not traveling as far as the coin mechanisms, youwill need to clean the channel beneath the coin slot. To gain access to this channel, use a %-inch wrench and remove all three nuts that secure the cover plate (refer to Figure 3-5). Removing the plate will provide access to the entire channel.
Also clean the inside surfaces of the secondary coin chutes, but when doing this be careful not to damage or bend the trip wires on the coin switches.
Figure 3-5 Removal of Plate Covering Rear of Coin Slot
Lubrication Do not apply lubrication to the coin mechanisms. The only points that may need lubrication (and only rarely) are the shafts of the scavenger buttons (coin rejection buttons) where they pass through the coin door. Apply only one drop of light machine oil, and be positive that no oil drops down onto a coin mechanism. Figure 3-6 shows this lubrication point.
Adjustment of Coin Switch Trip Wire In order for a coin switch to operate reliably when a coin travels down the secondary coin chute, the rest position of its trip wire should be as shown in Figure 3-7. Use extreme care when handling or touching these wires.
Manually hold down rejection button and apply one drop here
= Lock-out Wire
Figure 3-6 Close-Up View of Lubrication Point
Correctly adjusted trip wire
Figure 3-7 Detail View of Coin Switch and Trip Wire CRIMP TOGETHER MOUNTING STUD AT 2 ARROWS SHOWN
Figure 3-8 Securing the Coin Switch Trip Wire
Three problems can occur with trip wires—they can be too long, too short, or become loosened and fall off.
With a wire that is too long, you may have a problem of it catching on the opening in the cash box as a coin is accepted. You can cut off the end of the wire in small increments, making sure it still extends slightly through the “V” of the coin chute.
If the trip wire is too short (either by wrong adjustment or by being cut off too much), coins may slip by the wire without tripping it, and no credits will be given. The solution is to carefully bend and straighten out the wire to lengthen it. If you cannot straighten it sufficiently, contact your distributor to order another trip wire.
If the wire is loose and falls off its mounting stud, it will also cause no credits to be given. Secure the wire by crimping together both ends of the brasscolored mounting stud with a pair of pliers (see Figure 3-8). If you should ever need to remove the trip wire, the two halves of the mounting stud can be separated with a small screwdriver.
Mechanical Adjustments on Coin Mechanism Coin mechanisms are adjusted prior to shipment from the factory and normally will retain these adjustments for many months. If, due to wear or other causes, it becomes necessary to make new adjustments, remove the coin mechanism from the coin door. Then take it to a clean, well lighted area where it can be placed in a vertical position on a level surface (such as a bench top). Besides a screwdriver, you will
need several coins, including both newand old, worn ones. Figure 3-9 shows an exploded view of the mechanism and gives procedures for adjusting the kicker, separator, and the magnet gate. These adjustments should only be done by someone with experience in servicing coin mechanisms and who understands their operation.
General Troubleshooting Hints The first action is to look for jammed coins. After these have been removed, examine the coin path for presence of foreign material or loose objects (such as chewing gum, small metallic objects, paper wads, etc.). In cases where game usage is heavy, it may be necessary to clean the entire coin path periodically, in order to prevent build-up of contaminants that can hinder the movement of coins through the mechanisms. Also confirm that the trip wire on each coin switch is intact, and is properly adjusted. If troubles still persist, check the conditions and positions of the lock-out wires, and the mechanical adjustments on the coin mechanisms, before suspecting the electronics. If a coin mechanism rejects genuine coins, try to readjust it. If this is not successful, then replace it with a working mechanism.
C. FUSE REPLACEMENT Destroyer contains four fuses, two on the power supply assembly and two on the TV monitor assembly. These fuses are all easily accessible through the rear access door. Replace fuses only with the same type of fuse as follows:
TV Monitor Fuses: 3AG 1-amp slow-blow, 250 volts Power Supply Fuses: 3AG 2-amp slow-blow, 250 volts
D. LAMP REPLACEMENT Cabinet lighting is done with an eighteen-inch fluorescent tube. The bezel is lighted with an eighteen-inch black light tube. Both the fluorescent and black light are mounted in one lamp assembly. To remove the lamp assembly, follow the instructions in Figure 3-10.
E. REMOVING THE CONTROL PANEL Removing the Control Panel Assembly can easily be accomplished through the coin door by removing four %-20 wing nuts, split lock washers and flat washers at each corner of the Control Panel Assembly. Remove the Control Panel Assembly.
F. REMOVING THE TV MONITOR The TV monitor in Destroyer may be easily replaced. This is accomplished by opening the rear access door, unplugging the Molex connector from the monitor, removing the securing screws, and sliding the monitor out the back door. See Figure 3-11 for the location of the securing screws on the monitor.
ITEM IDENTIFICATIONS 1 Kicker and Separator Screws 2 Washers
7 Mainplate Assembly 8 “C" washer 9 Rail 10 Gate Assembly 12 Cradle Assembly
~~ 13 Upper Gate Pivot Spring 14 Undersize Lever Assembly 15 Magnet Gate Assembly 16 Magnet Gate Adjuster 17 Re! 18 Coverplate A: 19 Return Coverpl 20 Coverplate Studs Pivot Spring 23 Coin Release Lever
Kicker and separator . Set the acceptor with the back of the unit facing you In the test position. . Loosen the kicker and separator screws (1) and move the kicker (3) and the separator (4) as far to the right as they will go. Lightly tighten the screws. . Insert several test coins (both old and new) and note that some are returned by striking the separator. . Loosen the separator screw and move the separator a slight amount to the left. Lightly retighten the screw. . Insert the test coins again and, if some are still returned, repeat Step 4 until all the coins are accepted.
- Loosen the kicker screw and move the kicker as far to the left as it will go. Lightly retighten the screw. . Insert the test coins and note that some are returned. Loosen the kicker screw and move the kicker a slight amount to the right. Lightly retighten the screw. }. Insert the test coins again and, if some are still returned, repeat Step 8 until all the coins are accepted, ). Be sure that both screws are tight after the adjustments have been made.
Magnet gate
- Set the acceptor with the front of the unit facing you in the test position.
- Turn the magnet gate adjusting screw (16) out or counterclockwise until none of the coins will fit through.
- With a coin resting in the acceptor entrance, turn the adjuster in or clockwise until the coin barely passes through the magnet gate.
- Test this adjustment using several other coins (both old and new) and, if any fail to pass through the magnet gate, repeat Step 3 until all the coins are accepted.
- Fix the magnet gate adjusting screw in this position with a drop of glue.
Additional Cleaning
- Remove the transfer cradle (12) and the undersize lever (14).
- Use a pipe cleaner or similar effective cleaning tool to clean the bushings and pivot pins.
- Replace the transfer cradle and the undersize lever.
- To be certain the coin mechanism is completely free of any residue, place the mechanism in a solution of boiling water and mild detergent for several minutes. Carefully remove it and {et it air-dry completely before reinstalling in the door.
Figure 3-9 Adjustments on Coin Mechanism
REPLACING THE BLACK LIGHT TUBE
Remove the Front Housing Assembly as follows:
- Reach through the coin door and remove four %-20 wing nuts, one at each corner of the Control Panel Assembly.
. Disconnect the harness connector from the Control Panel Assembly, then remove the Control Panel Assembly.
. With a 0.125” hex wrench, remove three #10-32 x 1inch buttonhead screws and the metal seam cover from the top of the Front Housing Assembly. ‘METAL SEAM COVER . Lift off the Front Housing Assembly.
. With a Phillips-head screwdriver, remove two #8 x 1.5-inch wood screws from each side of the Display Light Assembly.
. Pull Display Light Assembly out of cabinet far enough to remove the black light.
. Re-assemble the cabinet, performing steps 1 through 6 in the reverse order.
an
FRONT HOUSING ASSEMBLY
CONTROL PANEL ASSEMBLY
REPLACING THE FLUORESCENT TUBE
- Remove the Display Plex Graphics Panel by using a 0.125-inch hex wrench to unscrew five #10-32 x 1-inch socket head screws.
- Remove the fluorescent tube.
Figure 3-10 Removing the Cabinet Light Assembly
Step 1
Step 2
Step 3
Step 4
Step 5 Refer to Figure 3-10 and remove the front housing assembly.
Remove two sets of screws, nuts, and washers at front of TV shelf assembly.
Remove two wood screws from back of TV shelf assembly.
Unplug Molex connector from TV monitor chassis.
Lift back of TV shelf assembly and slide out of cabinet.
Figure 3-11 Removal of TV Monitor
A. GENERAL INFORMATION The block diagram of Figure 4-1 shows the major controls, circuits and outputs of the game. Figure 4-2 is a block diagram of the Destroyer game PCB.
The game’s television monitor is a self-contained transistorized unit. Because the composite video signal sent to the monitor differs in many respects from the signal derived from commercial TV broadcasts, the picture appearing on the screen is unlike that of a home TV set and the monitor does not produce any sound. The game’s composite video signal is made to produce only four video levels instead of the more or less continuous shades of grey seen on a home TV screen, The background of the picture is black video level only, but game objects may use any of the four video levels.
THEORY OF OPERATION
ON/OFF
INTERLOCK ‘SWITCH
SWITCH ‘AC SOURCE ‘- GAME LIGHTING
PLAYER CONTROLS
COIN DOOR
COINAGE LAMP TV MONITOR
Figure 4-1
On the game PCB schematic diagram, Figure 4-5, the symbol “P” (appearing at various inputs of integrated circuit devices) indicates a connection of +5 volts DC through a pullup resistor. For easy reference, the game PCB is divided into grid sections. Along the short side of the board these sections are identified by letters A through R (skipping letters G, I, O and Q because they may be easily confused with the numbers 6, and.0 respectively). Along the long side of the board the numbers 1 through 12 are used. For example, sheet 1 of Figure 4-5 illustrates the type-7474 flip-flop, 2 at the lower left of the drawing. This device J2 will be found at coordinates J and 2 on the PCB.
Figure 4-3 is a harness diagram of the entire Destroyer game. This figure illustrates how all electrical and electronic assemblies are electrically connected together.
B. POWER SUPPLIES (lower left corner of sheet 1 Figure 4-5) The two AC voltage inputs to the board come from the 25 VAC and 16.5 VAC center-tapped secondary windings of the power transformer inside the Power Supply Assembly. The +5 volt regulated supply provides Vcc for most of the board’s integrated Destroyer Game Block Diagram
circuits. The +12 volt and —5 volt regulated supplies provide lower-current voltages for analog circuitry on the game PCB. The unregulated +18 volts connects to the audio driver stage for the game’s audio output.
C. CRYSTAL OSCILLATOR AND TV SYNC COUNTDOWN CHAINS A 12.096-MHz crystal oscillator (sheet 1 of Figure 4-5)generates the basic clock frequency that is divided down to produce the TV synchronization signals. The signals used to produce a TV monitor raster consisting of 262 horizontal lines at a horizontal frequency of 15,750 Hz (256H). Synchronized with line 240 is a vertical blanking pulse that occurs for the duration of 22 more horizontal scans, resulting in the total number of 262 lines per picture frame.
Besides being used for the TV raster, the TV timing signals are also used in the motion circuits, in the alphanumerics display circuit, in the microcomputer clock and in various other places on the board.
D. MICROCOMPUTER The microcomputer is the control center for the action of the circuitry that makes up the game. The microprocessing unit (MPU) sends out addresses on its address bus and accepts data or outputs data onto
NOTICE TO ALL PERSONS RECEIVING THIS ORAWING CONFIDENTIAL: Reproduction forbidden withoul the specitic written permission o Atar., Inc. Sunnyvale Calitornia. This drawing is only conditionally 'ssued. and either receipl nar possese,cn thereal confers or transters: fany right im. oF license 10 se, the subject matter of the Grawing or any design 9° technical information shown, hereon nor any right tereproduce this ramingor any part thereol excepl for manulacture by vendors of Atari Ineot- Poreted and for marutaciure under Ine corporation s wit fenlicense norighite reproduce this drawings granted oF the sunject matter thereot uniess by written agreement tailh oF written permission trom the corparation Figure 5-2 TV Shelf Assembly
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
I. ALPHANUMERICS During VBLANK, the MPU loads RAMs N4.and M4 with data at the address locations from multiplexers N3 and M3. During VBLANK, vertical and horizontal sync functions address the RAMs. Due to decoder N2 and gate P3, the alphanumerics can only appear in special zone on the TV monitor.
J. VIDEO OUTPUT Video output is synchronized to 6 MHz by latch L8, then fed into a resistive summing network to produce the multi-level video out signal.
K. WAVE GENERATOR Wave information stored in ROM K2is allowed to appear only on the two lines specified by the inputs to multiplexer L2. These two lines of information are changed in sucha fashion to resemble moving waves.
L. AUDIO Only one sound at a time can be produced. Sonar ping, low and high explosion all share the white noise, amplitude-modulated with a decaying envelope, generated at pin 3 of E9. Sonar ping is generated by a bandpass filter comprised of 3 operational amplifiers of H9. Sonar ping is gated out at pin9 of E9 by SONGATE. Low explosion is generated by a bandpass comprised of the remaining operational amplifier of H9. It is gated out by LE (low explosion). High explosion is a sum of low explosion and unbandpassed white noise. It is gated out by HE (high explosion). Motor sound is produced by the triangle waved output from half of the 556 timer H8, then amplitude modulated by the other half of the 556 through D10. Depth charge launch sound is gated and filtered random noise. The Attract mode signal turns off all sounds, except the sonar ping sound. Sonar ping is at a reduced volume during the Attract mode. This sound may be eliminated during the Attract mode by opening the solder pad between the collector of the 2N3643 transistor and pin 6 of D10 and soldering the jumper pad between the transistor and pin 5 of B10.
Ree c won le
44 PIN EDGE Pe
CONNECTOR oot Tower ee wearer Bley oe fee
[or j Ree)
2,
Wov FoR our Powe SUPPLY SCHEMATIC. ‘See 867197-01 SRT INS, Stow NC. RE ERE NS aw — TEST NS. Sa TEVERT TEKoOF ATER SPEAKER GED] 2EVRE
Figure 4-3 Destroyer Game Harness Diagram
vith oF
TRANSFORMER PCB A0OLSSS-O1 OOU!B 1-01 3] oe 8 | 2.0004 _ Y_ 1, 220V OR di @'5V R3« i HOw A : - VOLTAGE | Rign_ SAmp [2 SELECTICIN ~ Fee 3
BLOCK 3
SHOWN OR 4
oR ox : [ OR b | 3 POWER
& 8) "to R 9/PcB us 0 Y ; OuT Bu
Bu fi] sv bai ouT &
3 TP TP
INTERLOCK, ——, SWITCH Woot wR wy BRIS y BK | BK | 3 ce bates 5 {oir ON/OFF SWITCH INPUT Bxiw| 4 + But 718K
wiBK | 2 W/BKy |W GN |S acre
Figure 4-4 Destroyer Power Supply Schematic
na LDL are 8 ns ae pees
NOTICE To ALL PERSONS ECE!
CONFIDENTIAL. Reproduction
e
Diagram ic Figure 4-5 Destroyer PCB Schemati Taree — | Faderiew [oxo0-oner | een 3088 rar Exrenpe Sua does | isso, eee Soot res elojelele[o foes [ress elo Bees Pear waar ® Tau sug RERLES Corre
Sheet 1 of 5
Figure 4-5 Destroyer PCB Schematic Diagram Sheet 2 of 5
~ ‘VEGARO® r" Wom | - a LANE: owe it
preeces
Figure 4-5 Destroyer PCB Schematic Diagram Sheet 3 of 5
Sheet 4 of 5 Figure 4-5 Destroyer PCB Schematic Diagram
i Figure 4-5 Destroyer PCB Schematic Diagram . Sheet 5 of 5
Figure 4-6 Motorola TV Monitor Schematic
Figure 4-6 TEC TV Monitor Schematic
ILLUSTRATED PARTS CATALOG
The purpose of this Chapter is to provide you with the necessary information for ordering replacement parts for the Destroyer Game.
When ordering parts from your distributor, give the part number, part name, applicable figure number of this list, and the serial number of your Destroyer game. This will help to avoid confusion and mistakes in your order. We hope the results will be less downtime and more profit from your Destroyer game.
If there are any questions about this list, please contact Atari’s Customer Service Department by telephone Monday through Friday, from 7:30 a.m. to 4 p.m. Pacific Time. From California, Alaska and Hawaii, call (408) 984-1900, from the remaining 47 states call (800) 538-6892 (toll-free).
Your game will include either the Motorola or TEC monitor, depending on their availability during production.
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING. ci
(TEMS NOT SHOWN ¢
NOTICE TO ALL PERSONS RECEIVING THIS ORAWING
]
i
Figure 5-1 Destroyer Final Assembly
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING. CONFIDENTIAL. Reprocuction forbidden without the Specific writen permission of Atari. inc. Sunnyvale nia. This drawing Is cnly conditionally issued. and "receipt nor possession thereat conlers or transfers fany righ in. oF license #0 use. the subject matter of the Grawing oF any design or lechaical information shown thereon. norany nightie reproduce ths Grawing or any part Inoreo!. except for manulacture by vendors of Atariincorporated and for manufacture under the corporation's writ: lenlicense. no nightto reproduce nisdrawing!s granted or the subject matter thereof Unless by wallen agreement jth oF written permission om the corporation
Figure 5-1 Destroyer Final Assembly
Figure 5-1 Destroyer Final Assembly
ATARI
SS Part Number Description
| 1 | A008577-O1 | 1 | Tv Shelf Assy - See Figure 5-2 |
| 2 | 009264-01 | 2 | Block TV Tray |
| 3 | 72-6812 | 14 | Screw, SM. #8 x 3/4 Lg., Phil Pan Hd. |
| 4 | 75-010S | 4 | #10 Washer Flat |
| 5 | 75-040 | {o | #10 Washer, Split-Lock |
| 6 | 75-5132N | 4 | Bolt, Carriage, #10-24 x 2.00 Lg. |
| 7 | 75-9118 | 4 | #10-24 Nut, Hex |
| 8 | A009511-01 | 1 | Power Switch & Harness Assy |
| 9 | 82-1824 | 8 | Wood Screw, #8 x 1.50" Lg. Flat Hd. Phil |
| 10 | A009013-01 | 1 | Power Switch Harness |
| il | 72-6610 | 25 | Screw, SM., Pan Hd., Phil., #6 x 5/8" Lg. |
| 12 | 009773-01 | 1 | Rear Bezel W/Graphics |
| 13 | 008572-01 | 1 | Monitor Mask |
| 14 | 009763-01 | 1 | Vacuum Formed Overlay W/Graphics |
| 16 | A009341-01 | 1 | Mirror/Tape Assembly |
| 17 | AO008557-01 | 1 | Mirror Tie-Down Panel Assy |
| 21 | 009774-01 | 1 | Front Bezel, with Graphics |
| 22 | A009270-01 | Ref | Flourescent Light Harness |
| 23 | 78-67032 | A/R | Black Photo Tape |
| 24 | A008568-01 | 1 | Display Light Assembly - See Figure 5-3 |
| 25 | A006548-01 | Be | Slide Switch Assembly |
| 26 | 4009770-02 | 1 | Cabinet Assembly with Graphics |
| 27 | A009083-01 | 1 | Coin Door Final Assembly - See Figure 5-4 |
| 28 | 75-5516B | 4 | Bolt, Carriage, #4-20 x 1.00" Lg, Black |
| 29 | 75-935S | 4 | Nut, Wing 4-20 |
| 30 | 75-045 | 4 | Washer Split Lock, % |
| 31 | 75-0158 | 8 | Washer, Flat %" |
| 32 | 006870-01 | L | Bracket, Coin Box |
| 33 | 009343-01 | 1 | Yoke Shield |
| 34 | A007902-01 | 1 | Cash Box Assembly |
| A007197-01 | 1 | Power Supply Assembly (B) - See Figure 5-6 |
A007784-01 78-25001 Power Cord Assembly Screw Down Tie Wrap
© Warner Communications Company
JA ATART
A030114-01 A009626-02 A009775~01 43 A009528-01 44 72-6808 45 72-6608 46 001638-01 47 A009760-01 48 82-8016 49 75-99090006 50 A009766-01 51 75-5516B 52 TM~106
55 006305-01 56 A006683-XX 57 A006647-02 58 005233-01 59 46-201202 60 009345-01 6l 75-990505S 62 009992-01 63 ST-106 sss tae sesae Ther ff Figure 5-1 Destroyer Final Assembly
Pe HPWWEPNHEEPH EEE
PR ARPNEHPRH DESCRIPTION.
Main Harness R.F. Shield Box Assembly R.F. Shield PCB Assembly — See Figure 5~7 Destroyer Game PCB Assembly - See Figure 5-8 Screw, SM., Pan., Hd., Phil., #8 x 4" Lg. Screw, SM., Pan., Hd., Phil., #6 x % Lg. Bracket Panel MTG Front Housing Assembly Screw, Button Hd. Socket Cap, 10-32 x 1.00" Lg. Well Nut, Blind Hole Fastener, 10-32 Control Panel Assembly - See Figure 5-9 Bolt Carriage #%-20 x 1.00" Lg., Black Operation, Maintenance and Service Manual
Printed Poly Bag Shipping Container Assembly Rear Door Assembly W/Lock Rear Door Seal Fuse, 2 AMP Seam Cover #%-20 Nylon Lock Nuts On/Off Switch Enclosure Self Test Chart
the data bus. When the MPU is reset, by receiving first a low level and then a high level on its RESET line, it outputs addresses that cause the program memory to put data onto the data bus. The MPU reads this data and uses it to address the main program. The main program instructs the MPU to execute operations and at which address to execute them. This controls the flow of data on the bus and “reads” inputs and “writes” to outputs. Data may flow into the MPU from program memory, “zero page” (read/write) random-access memory (RAM), and from tri-state input multiplexers at D7 and E7, or tri-state drivers from the option switches. Data may flow out of the MPU to zero-page RAMS, to alphanumerics RAMS N4 and M4, input latches of picture ROMS, output latches, to the inputs of the minor object counters, and major object RAMS. The 16 address bus lines are labeled ABUS. The 8 data bus lines are labeled DBUS. For purposes of timing in the program, the interrupt request (IRQ) line of the MPU is strobed 4 times per picture frame. The non-maskable interrupt (NMI) line is strobed when valid potentiometer (player's depth control) data is present (see 1/O section). E. ADDRESS MAP (Schematic Sheet 1) The address map is provided as a troubleshooting aid for the technician using Atari’s Computer Test Fixture CTF-1. This map lists all the addresses in both binary and hexadecimal form, for enabling game circuitry. With the CTF-1 test fixture and the accessory diagnostic board, a technician can address a suspect circuit and troubleshoot the circuit while it is in an address loop. F. INPUT/OUITPUT Digital Output The digital outputs of the MPU consist of the unbuffered data and address lines. The data BUS is buffered by AND gates E5 and E6. The address bus is buffered by AND gates A4, B4 and C4. This buffering provides more power to the signals and does not change the information content. The BUS lines 0, 1,2, 12, 13 and 14 are decoded by address decoders A7 and D4. These decoders provide signals for enabling the appropriate circuits. For example MAJOBJSEL (major object select) is gated
with ABUSO and WRITE to write the position RAMS in the major object circuitry. Address decoding for other functions is similar. Inputs Digital inputs are enabled by their own decoder signals. For example, inputs for the option switches are enabled by the signal SWRD (switch read) that strobes tri-state buffer D8. Analog inputs come from the player's depth control potentiometer. The voltage is compared by comparator R9 (LM319) to a voltage ramp provided by a discrete analog circuit that conditions the VBLANK signal. When the ramp voltage exceeds the input voltage an NMI (non-maskable interrupt) signal is generated. The computer then reads the VSYNCdata functions from tri-state line receiver D1 to tell where the cursor should be located. G. MINOR OBJECT CIRCUIT There are 2 identical minor object circuits. Minor object pictures are stored in ROMs _ F4and K4. Minor objects consist of depth charge pictures, charge explosion pictures, and post-explosion score pictures. Counters H5 and H6 (J5 and J6) are loaded with horizontal position information, and counters F5 and Fé (K5 and K6) are loaded with vertical position information. The top four bits of each counter are combined by NOR gates at H7 (J7) to provide “window” signals within which picture information is enabled. The low bits of these counters address ROM F4 (K4) and multiplexer H4 (J4) to provide serial picture data to the video summer. Latch E4 contains the code for which object is to be displayed. H. MAJOR OBJECT CIRCUIT Picture information for the destroyer, submarines, and submarine explosion is stored in ROMs P8 and N8. The ROM information is multiplexed by multiplexer N7 to provide serial video data. Four levels of video are provided by combining object level 1 and object level 0 in the video summing network. During VBLANK, multiplexer P2 allows the MPU to address picture RAM M5 and horizontal position RAMs M6 and P5, while data is written into the RAMs. During VBLANK, vertical sync functions address the RAMs. The ADDRESS at which the horizontal position data is stored, determines which of 15 vertical position bands the pictures displayed. Exclusive OR GATES at L7 and P7, controlled by D4 of M5 control the direction in which the subs and destroyer point. D1 and D2 of M5 choose which picture is displayed and D3 decides which scan window to enable.
1z
Zp aang wesde1q 490]g Fd awed 4240.359q
#
ATARI" Figure 5-2 TV Shelf Assembly
| Item | Part Number | Qty. | Description |
| 1 | 008556-01 | 1 | T.V. Shelf |
| 2 | 72-6812 | 8 | Screws, Self Tapping, #8 x 3/4 Phil. Pan Hd |
| 3 | 005594 | 4 | Monitor Tie Down |
| 4 | 92-032 | 1 | 23-inch TV Monitor, Motorola Model M7000-155 |
or 92-030 23-inch TV Monitor, TEC Model TM-623
| 5 | 006319-02 | L | Copyright Decal |
© | viorer Communoations Gomaany
Figure 5-3 Display Light Assembly NOTICE TO ALL PERSONS RECEIVING THIS ORAWING CONFIDENTIAL: Reproduction forbidden without the specific writlen permission of Atari, Inc. Sunnyvale, California. This drawing is only conditionally sued. and neither receipt nor possessior thereot confers or transters any right in. or icense to use. the subjact matter of the ‘rawing or any design or technical information shown thereon. norany righttoseproduce thisarawing or any thereof, except for manutacture by vendors of Atari NCO erated and for mangtacture under the corporation's wr tenvicense.no rightto reproduce this drawing is granted or the subject mater thereo! unless by written agreement wth oF written permission trom the corporation
A. ATARI’ Figure 5-3 Display Light Assembly
| Item | Part Number | Qty. | Description |
| 1 | A008860-01 | ib | Black Light Assembly 18" |
| 2 | 005495-01 | 1 | 18~Inch Fluorescent Light Assembly |
| 3 | A008561-01 | 1l | Light Mount Assembly |
| 4 | 72-6812 | 4 | #8 x 3/4" S.M, Screw |
| 5 | 75-0108 | 4 | Washer Flat, #10 |
| 6 | 4009270-01 | 1 | Fluorescent Light Harness |
| 8 | 70-306 | 1 | Fluorescent Tube 18" (F15 T8/BL) |
© 4 warner Communications Company
fe) o 28 PES Z7R fark
<
<o mx aS> r Ea A CoA oO 28 eas £ NOTICE TO ALL PERSONS RECEIVING THIS DRAWING. CONFIDENTIAL Reproduction forbidden without the
ter tnereo! unless by written agree ten permission from the corporation,
Ho
0 0°
(3
Figure 5-4 Coin Door Final Assembly
A ATARI" Figure 5-4 Coin Door Final Assembly
| Item | Part Number | Qty. | Description |
| 1 | A006794-01 | 1 | Coin Door Assy. for American Quarter Only -See Figure 5-5 |
A006794-02 Ref.| Coin Door Assy. for Belgian 5 Francs Only ~-See Figure 5-5 A006794-03 Ref.| Coin Door Assy. for German Mark Only -See Figure 5-5 A006794-04 Ref.|Coin Door Assy. for Swedish Krona Only -See Figure 5-5 A006794-05 Ref.|Coin Door Assy. for Japanese 100 Yen Only -See Figure 5-5 A006794-06 Ref.|Ccoin Door Assy. for English 10 Pence Only -See Figure 5- A006794-07 Ref.| coin Door Assy. for Australian 20-Cent Piece Only- See Figure 5-5
| 2 | A006921-01 | 1 | Harness Assembly |
gy Nee BEA] ways Sy BA BECO co) eo GB __| | | sviaz
Figure 5-5 Coin Door Assembly L eto [® 6) i Ku sez (2) (7)
fp Ses
@OOQ
A ATARI’ Figure 5-5 Coin Door Assembly
Item Part Number 1 ‘A007637-01 A007637-02 007637-03 A007637-04 A007637-05 A007637-06 A007637-07
75-9165, A007639-O1 A007640-01 A002465-01 004320-01 004341-01 004344-01 004340-01 10 004337-01 il 004338-01 12 004336-01 a: 004326-01 14 75-046 15 006904-01 16 007359-01 17 70-11-47 18 73-3008 19 75-9914001 20 75-0268 21 75-00516 22 008629-01 23 71-2118 24 71-1225CU 71-125FB 71-121MG 71-121KS 71-12100YT 71-1210PE 71-1220CA 25 007753-01 26 A007638-01 Description Front Bezel Assy. - Used -01 Coin Front Bezel Assy. - Used -02 Coin Front. Bezel Assy. - Used -03 Coin Front Bezel Assy. - Used -04 Coin Front. Bezel Assy. - Used -05 Coin Front Bezel Assy. - Used -06 Coin Front Bezel Assy. - Used -07 Coin Nut 6-32 Coin Lock-Out Assembly Coin switch Assembly Coin Counter Assembly Coin Door Weldment Secondary Coin Chute Key Loop Spring-Return Bracket, Wire Form Lock-Out, Wire Form, R.H. Lock-Out, Wire Form, L-H. Button, Scavenger Lock Washer, #6 Spacer Lamp Socket Lamp Retaining “C" Ring, Truarc #5103-25 Self-Threading Nut, Tinnerman #SR186006 Washer #6 Kepnut, Style 842, Stl., 6-32 spring Lock Assembly, Hudson Lock Coin Mechanism for American Quarter only Coin Mechanism for Belgian 5 Francs Only Coin Mechanism for German Mark only Coin Mechanism for Swedish Krona Only Coin Mechanism for Japanese 100 Yen Only Coin Mechanism for English 10 Pence Only Coin Mechanism for Australian 20-Cent Piece only
Plate, Anti-Probe Switch Assembly - Slam
© 4 Warnes Communications Company
OSC)
a e Ceeses) fe e o Teeen eso]
Figure 5-6 Power Supply Assembly res REQD
ii Figure 5-6 Power Supply Assembly ATARI
| Item | Part Number | Qty. | Description |
| 1 | A009266-01 | 1 | Power Supply Base Weldment Assembly | |
| 2 | A006886-01 | 1 | Transformer Termination Assembly "Type B" |
| 3 | 29-053 | 1 | Cap., Sprague Electrolytic 26,000mf @ 15V |
| 4 | 78-70501SC | 1 | Brkt., Cap. Mtg. Sprague #4586-48 |
| 5 | A006555-01 | 1 | P.C. Board Rectifier |
| 7 | 79-4411004 | 5 | Fuse Holder, Panel Mounting |
| 8 | 41-2003 | 1 | Filter, Power Line, 5 AMP |
| 9 | A006958-C1 | A/R | Volt Sel Block 95V |
| 10 | A006958-02 | = | Volt Sel Block 110v |
| 11 | A006958-03 | " | Volt Sel Block 205V |
| 12 | A006958-04 | " | Volt Sel Block 220V |
| 13 | 78-2708 | 1 | Grommet ,Plastic |
| 14 | 72-1808S | 3 | Screw Pan Hd., #8-32 x *" Lg. |
| 15 | 72-1812S | 6 | Screw Pan Hd., #8-32 x 3/4" Lg. |
| 16 | 75-038 | 9 | Washer, Lock, External Star #8 |
| 17 | 75-9188 | 9 | Nut Hex #8 |
| 18 | 75-018S | 4 | Washer Flat #8 |
| 19 | BO007192-01 | 1 | Power Switch Termination |
| 20 | A007444-01 | 1 | Power In Harness |
| 21 | 46-203801 | 1 | Fuse, 8 AMP, 125V, 3 AG Fast Acting |
| 22 | 46-201251 | 2 | Fuse, 24 AMP, 125V, Slow Acting |
w') ‘Warner Communications Company
‘sod 0}
‘S274 Ol YOLIAGN| VVWANS
& z n
HEAR LIS v/ET
Waren \ ape + noa zt Moa ' yno Buyjnd |B eoreqdr yn |
ro) NOTICE 70 ALL PERSONS RECEIVING THIS DRAWING. CONFIDENTIAL: Reproduction forbidden without the specie writien permission of Atari, Ine., Sunayvale Califorma, This drawing 1S only conditianally saved, and either eeceipt ox possession thereof conters oF Iransters, any right in. 0 license to Use, the subject matter of tne Grawing of any design or technical intormation shown ‘ereon, nov any right lo reproduce this arawingor any part Itereo, except for manulacture by vendors of Atari Incorporated and for malnutacture under tne corporation's writfenticense.noright to reproduce this drawings granted or the subject matter thereof unless by written agreement with oF written permission from the corporation.
TAXMAN ASZANWIAE HI 20D e GaLvzian; 3uaHM NIBLVWIXOUddY ACISUVS HOVILY ©
ao 2 eg 9 o 9 cer Oo} ny N N
o oO
i
\
- ie) |
Figure 5-7 RF Shield PCB Assembly
A ATARI Figure 5-7 RF Shield PCB Assembly
Part Number
006549-01 79-517222 27-250104 27A-250104 41-3003 41-3004 52-003 52-004 009468-01 Coraubwonne
© A warmer Communications Company Description
P. C. Board Connector, 44 Pin P. C. Mount Cap., Cer Disc, .luf, 25V Cap., Cer Disc, .luf, 25V (Small) (Bottom Row) Inductor, 100uh,(Large) Inductor, 100uh (Small) (Bottom Row) Jumper, .60 Centers Jumper, .30 Centers Decal, R. F. Shield Label
NOTICE TO ALL PERSONS RECEIVING THIS ORAWING CONFIDENTIAL. Reproduction forbidden without tne spacitic written permission ot Atan. Inc.. Sunnyvale, California. This drawing 's only conditionally issued, and neither receipt nor possession thereo! confers or iransters , any right in. or licange (0 use, the subject matter of the ‘drawing oF any design oF technical information shown thereon. norany righ! 1a reproduce this drawing or any part thereof except for manufacture by vendors of Atari Inc porated and for manufacture under the corparation's wr tenlicense na right{o reproduce this drawings granted or the subject matter thereof unless by weitten agreement with oF wetter permission trom the comoration woua to-
(rear nezsi be
90-600! COU
WOU Figure 5-8 Destroyer Game PCB Assembly
iN Figure 5-8 Destroyer Game PCB Assembly ATARI
009529-01 P.C. Board 10-5101 Resistor, Carbon Comp., 5%, XW, R87 10-5102 won R3,7=21,24,25 28-35, 38, 45- 53,55-58,97-
10-5103 R23,54,61,62, 67-69, 73,89
10-5104
10-5106
10-5152
10-5153
10-5154
10-5220
10-5221
10-5222 R64-66 , 74 R63
R6,27
R71
R43
R22
R4,5, 39,40 R37,41,82,92,
10-5223 R76
10-5272 1 R88
10-5331 R1,2,84,85,90
10-5332 R70
10-5333 R72,75,79 10-5334 R83
10-5392 R80, 81 10-5393 R42
10-5473 R77
10-5474 R59,60 Ce a
© warner Communications Company
ATARI’ Figure 5-8 Destroyer Game PCB Assembly
| Tem | Fat ember | [0 | Deserinton | Tem] | Partemer | [Oe | Description | |||
| 22 [05562 | 2 || Rostov, Carton | Compe, 58, BH, 5 Oo FO6,TR | 6 | sp-nar7s | 1 | |fte, mars | me | ||||
| 2 | toseat | 2 | vem | am | 600m 3686 | 1 | sy-nasin | nlf | gain | 2 AS, | ||
| oi | 10:Sie, | 1 | ia | ww 6K | KR | erence, | |||||
| 28) dosent | * | " | . | wo | Saag | Be | 8 | 97-74795, | 1 | #74195 | cy |
| bi | 89 | S7=THLS206 | v | Tabs 264 | Cy | ||||||
| . | | 31-7415257 | r | 7aLs257 | ‘DT,E7 | ||||||
| » | senso | 1 |] seiepee, 508 ohm | 195 | bl eras | oa | | ren | 7 | ||||
| a0 | rsesoswiro | | 2 |) sentotor, kieawoun'y 104, 6 em | 6 | ba aie | yee | : | |||||
| * | 93 | s7-4066 | 1 | “4066 | |||||||
| bed | 96 | 37-556 | 1 | "556 | cr | ||||||
| bd | 95 | 57-¥e3%0, | v | me3340- | p10, | ||||||
| a4 | rieaoni96 | 2 flewsestor, oie, | 100, | aot erie | 3 ae | ty | Re | m | |||
| as | aeaseroe | | | cc | ee | w lanume | | | en | on | |||
| hea | se srano23 | 1] | eoseror, | 029 | ||||||
| 26 | ascasoaes | 2 | . | + | ot | cohas | ov | 97010 | ap | raz | o | |
| a7 | 2e-2s0u07 | | | ey | 109 37-7905 | ry | 105 | @ | ||||
| 28 | 24czsor08 | 5 | " | tom | ep | ror] s7-ror006 | 1 |) autio ap | zBmone | vo | ||
| x9 | 2e2:0708 | rife» | “a0 "em | x04 | |||||||
| 40 | nc2soure | ‘S| | a | om | v | ||||||
| a | aeasonoe | al} | oo | 048,70,86 | rod | ||||||
| a arasoees | ail» | "lena = | 602,64 | 103 6001 | 1 || svisen, momentary, sr5t | |||||
| aa] araseos | rif | os | “a1 "60 | tos setters | 1 |] | ow | ssrocteion tr, srs x | eo | ||
| 4c | ar-asoax | ‘ | " | lat | 5658 0, | 107 m-10086 | 2 || screw, ten Wis Phil, 6232 x Ste, CaS | ||||
| . | , | . | we | 104) 75-016 | 2 || sooner, ria, #6 | |||||
| 45 | aveasoroe | ol} | « | "a | ghana | 104 15-056 | 2 || eshory Lasky Tat. Stary #6 | ||||
| ait | 119] rsa0e | 2 | mot, Hers 6932, CxS |
ooo ni 1a v4
| ian | nner. o8001 | 1 | neatsise | (or 329) | ||||
| noossio0 | |i | ||» | (or Ta008) | ||||
| 46 anetoran | 1 |] | ptpped Mica, 100%, | 220 or | ene | nef ream | sal] cocane | (tor Tont006 Heatat> |
| | aos | aff | om | aways | 117) 16005 | 1 || stipe | (or 229) | |
| «| w010 | 1]]# | tantes Feces 10%, | Baz et | 635 | 1 |
6 ns 0 w J
| Tam [Pant Foner | = | Ten | Pan amber | 107 | Deseripaen |
| 2 | 1a |acazok0 | 1 |] fecker, cosh nats Tonertton | ||
| 52 {naavore | 2 |] ptoce, swore | on | 12 | |
| 53 faransoot | a |] | amon | cass | 1p |
| % | 125 soe102 | 1 | a1, 12.096 He | n |
rs 16
| 57 | ssassece | 1H | sranacstoe, me | a | w | |||||
| sa | scanned | a | lpn | anaes | aa | ve | ||||
| s9 | se-ansisn | fs | | ec | 6 | 123}s0.0001 | 1 |] rterapracessor, HEss00L | o1cs | |||
| © | 1302-7005 | 3 | [fm | eases | |||||
| a | 131fs0-7019 | afje | amas | caps | |||||
| “ | 1o2)poeron | 2 | oun | nan | |||||
| 63 | 1-100 | 2 |[ re, m0 | pe | |||||||
| 66 | sence | al | moe | ever | 134 | |||||
| 65 | m-moe | afin | 0. | 23,269 | 5 | |||||
| 6 | sre | rf | see | nl | 1303-1 | 1 |) peoth enarge syne Poor | " | |||
| | arr | 7 | 98 | sect, | sn7foaorz2-0 | a |] =m minor obicete | rote | |||
| 6a | 37-7410 | 1 | mo | Me | heal acon | * | 7 | Se | = | |
| pl aes | type | mee | 7 | apjoxnt eat | 1 | Halor Objects 2 | ™ | ||
| ba be | a | ae | to | solo 001 | af | Rohaniertes | m | ||
| reifopos6-01 | ill | ave | ry | ||||||
| ni | ar-raa8 | 7 | co) | 8 | ut | |||||
| na| s143e | sl] | + | nae | 12.078. | wl | ||||
| 13 | y-7437 | L | “437 | Be | so | | |||||
| ie | emag | ale | uae | ayn A? | 14s) oxma01 | 1 || seven change vaow | 1500 10 | n | ||
| 7 | samt | af) | sun | avi | 14elormaron | iff | = | roe | 7900 x | n |
| i | aan | | | en | n | owhooiaeo, | a |] © | = rao | 7600 x0 | nm | |
| a lieouae | Pa | | ene | ber | 10 owr4eeot | aff | © | poe | 2600 | 2B |
| 2] sr-r93 | 1 | 499 | crs | | | |||||
| | sree | 1 | |= | x16 | os | |||||
| to| a2 | a|] | » | ras. | 2,826 | |||||
| | a-7esa | rif» | ass | ” | ||||||
| se | sms? | a] | «mse | 299,49 | ||||||
| 3] ar-rasia | all | © | asim | ama | |||||
| 4 | sr-rasise | af) | masies | vie | ||||||
| 5) 3-712 | a] | * | mam | rs |
Drove: conmcaton conser
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL. Reproduciion forbidden without the specific written permission of Aan, Inc.. Sunnyvale California. This drawing s anly conditionally issued, and ‘ether recerpt nor possession thereot confersor transfers any right in. oF license to use. the subject matter of the drawing or any design or technical information shown thereon. nor any ght to repreduce this drawingor ary part thereot. except for manularture by vendors of Atari Incorporated and ter manulactute under the corporation s wettenlicense.no night to reproduce this drawing s granted or the subject matter thereo! unless by written agreement with or written permission trom the corporation t
z-— wow { TESTED epioes SESE? PT
SF
Figure 5-8 Destroyer Game PCB Assembly 2200 mF
hii
35,
N. Figure 5-8 Destroyer Game PCB Assembly ATARI’
Part Number Description 009529-01 P.C. Board 10-5101 Resistor, Carbon Comp., 5%, %W, 100 Ohm R87
| 3. | 10-5102 | 44 | " | " | mom om 1K | R3,7221,24,25 |
28-35, 38,45- 53,55-58,97- 100 ;
| 4 | 10-5103 | 9 | " | " | now om 10K" R23,54,61,62, |
67469, 73,89
| 5 | 10-5104 | 4 | " | " | wm | 100K "R64 =66, 74 | |
| 6 | 10-5106 | 1 | " | " | now om OM | R63 | |
| 7 | 10-5152 | 2 | " | " | mom om ASK | R627 | |
| 8 | 10-5153 | 1 | " | 7 | moo om 45K | RTL | |
| 9 | 10-5154 | 1 | " | 4 | wom om 150K | R43 | |
| 10 | 10-5220 | 1 | " | " | wo | 22 | R22 |
| 11 | 10-5221 | 4 | " | " | um | 220, | R45, 39,40 |
| 12 | 10-5222 | 5 | " | " | mow mt 2.2K" -R37,41,82,92, | ||
| 13 | 10-5223 | 1 | " | " | nom om 22K" R76 | ||
| 14 | 10-5272 | 1 | " | " | "ww 2.7K | R88 | |
| 15 | 10-5331 | 6 | " | " | nm | 3300" RL, 2,84,85,90 | |
| 16 | 10-5332 | 1 | " | u | mom | 343K R70 | |
| 17 | 10-5333 | 3 | " | " | "ow om 33K R72,75,79 | ||
| 18 | 10-5334 | 1 | " | " | wom om 330K "R83 | ||
| 19 | 10-5392 | 2 | " | " | um om 349K "R80, 81 | ||
| 20 | 10-5393 | 1 | " | " | wom om 39K | RAD | |
| 21 | 10-5473 | 1 | we | " | nom om 47K | RIT | |
| 22 | 10-5474 | 2 | " | " | um | 470K R59,60 |
© warner Communications Company
ATARI’ Figure 5-8 Destroyer Game PCB Assembly Tes [Pan Number [QW Description
| 23 | ronssen | 2 | |[Restazor, carton Conp., 5h, Wf, 5.68 Ohe R26,78 | ||
| 2u | r0-seen | 2 | " | nn 60 | B36 |
| 23 | 0.5607 | 1 | ete | onl | ae Hay |
| 26 | roasnar | 1 | cc | ace |
v ey
| 9 | 19-3503 | 1 || tetepoe, $08 ohm | ms |
| 30 | 19-s0suar0 | 2 || aesteeor, wirewourd, 108, 6 Ohm | 196 |
”
| x | ar-roniee | 2 || camecteor, Myer, | 100Y, | Lue | o71,72 | |
| 38 | ma2s0106 | 8 | % | Blace, | 25%, | 1028, 38 Hy |
| 36 | rsasona6 | 2 | . | “ | - | ont |
| a7 | aecrsouer | 2 | " | " | + | ame |
| ae | 24250108 | 1 | * | . | 1000. | |
| 9 | ren2sor28 | 1 | » | "00 | ||
| to | 2250476 | 1 | "ao | |||
| ‘a | 27-230102 | af | * | on | ||
| 42 | 27-250223 | || | = | " | » | wo |
| 4a | 27-2so103 | 1 | . | * | » | |
| aa | 27-2s0226 | 6 | ° | . | "oa | |
| 45 | 27-2500 | wolf | " | » | " | eua325 |
Pan seca ee) 2730582 Suseis3) 055,672 ers, dey79 a1 aahariae
| os | maiz | 1 | Dipped Mien, 100%, | 220 pF 086 | |
| a7 | eon | 2 | . | "yo | 9,5 |
| as | 3-010 | 1 | Tames, Hace, IY, | 2D ut | 635 |
°
AS a | st
| st areanoua | 2 |] toe, wore | m2 | |
| 3 |st-anoo | |] | neon | ons |
se
| 57 | sseanseue | 2 |] tranetaor, 203640 | a | |
| 58 | ahe2H603 | “ | 364 | eas |
| 59 | si-2nsi80 | 1 | *xsi90 | % |
« “ &
| 63 | 37-7400 | 2 |} x, | 200 | |
| + | s7a7402 | a | ||" | mor |
| 5 | 37-7008 | a | |} | 08 |
| 6 | 37-7008 | 1 | 70 | |
| «7 | 37-708, | 7 | |)» | 2408 |
| [>-710 | afin | mo | |
| oof 37-7120 | af} | «mo |
0 | s7=7425, Fa |
| ni | sre7ea | ra | | ed | ‘s |
| ra | sr-7032 | s |] ° | 7s | 22,87,08,88, |
cs
| 73] sr-r0a7 | af} | mr | 2 | |
| ra | a7-7002 | af} | mee | 2, 06,47 | |
| 75| sr=7a7a | Fal | 2,160 | ||
| 76 a7-r08% | al] | + | rast | a |
| nn| a7-7086 | Fa | oe) | ue | ||
| ra | 97-7493 | Pa | ce) | o | ||
| 19| sv-7an6 | a|] | = | are | |
| 20 | 70181 | 3 | pas | 2,6, | |
| a | 3770153 | ra | oe | ” | ||
| 92 | 37-70157 | af) | nasr | 92,9000 | |
| a9) s7-7ausi61 | aff | mse | ae ta | |
| | 97eTaLsi64 | al] | + | sastee | 1320) |
| ahs | a7-74174 | al] | «mm | Pay |
Par Rmber Desorption
| 6 [57-7017 | | apse, | ms | i | |
| 7 | srarasie | 22] | © | raster | F5,85,25,05, |
15,76,86,36) U6, )47
| 8 | a7-7ai95, | 1 |] = | miss | Re | |
| 9 | sr-raiszue | al] | masa | pm | |
| 90 | s7-na15257 | ail" | Tausest | oe? | |
| st | a7-8107 | 1 | ant | ps | |
| 92 | 37.990 | r|] | eos | rf | |
| 93 | s71066 | 1 | ||» | sose | Ps |
| oa | 37-556 | 1 | 86 | s | |
| 9s | y-reast0 | 1 | e330 | oo | |
| 96 | 37s | 1|] | © | usr | 9 |
| 97 | s7aunsan | 2 |] © | eee | 3,89 | |
| 96 | syaunse9 | 1 || rentater, | 4323 | ||
| 99 | s7-7012 | 1 | " | m2 | e |
| 09] 37-7908, | 1 | . | 7908 | o |
| roi} s7-raar006 | 1 || svete amp | tatoos | m0 |
1: 20: 103 62-00, 1 || seteen, momentary, Sest
| 106 66an18e17 | a |] +" | aepoateton om, SPST x @ | ae |
107] 7226080 2 || serew, Pan ta, PALL, 6-52 x 4 Lg, CRES
| 108) | 75-016 | 2|| | Manner, eter, #6 |
109) 75.056 2 || waaner, Lock, Inte Star, #6 119 75.9166 2 || Nee, mex, 6-32, CHES m1
| 114) 7806001 | 1 |] nanessne | Cor wise) |
| us}ooeate- | 1 | " | (foe T4100) |
| nig 7823016 | || Conant | Clo 7081008 Hentstne) |
| 17} 78-26008 | 1 |] stipe | Cor 029) |
ws rr
| Rom] | Par Nanber | |. | Description |
ani |rene2o40 1 |] soceee, s0nPia, Meus nsertion a 123] 1]
| 125]s0-102 | 1 || cryseat, 12.096 we | 1 |
126] a rea
| 12930-6001 | 1 | wor, NESAOOL | vies | |
| 12030-7005 | 3 | |], | azsas | 15,7506 |
| rai]s0-7019 | al) | amine | 2,03 | |
| 3290-70 | 2 | |i | noes | ca |
a3] ws
| 136Joso131-01 | 1 || bepen charae syne ow | ” | ||
| rar]oros2-01 | 2 || = | minor objects | Pak | |
| 138) 020133-01 | al] | + | © Majer objeees 2 | xs |
| 133] o30134-01 | a || * | © Major objects 2 | Ps | |
| uo) 030135-01 | al] | Atphannertes | Pe | |
| 141] 030136-01 | aif | Ravan | Ke |
eq 143] 5) 16} wt asl
| 149) osn4e-01 | 1 |]oepen charge ROM | 3 |
NOTICE TO ALL PERSONS RECEIVING THIS ORAWING CONFIDENTIAL: Reproduction forbidden without the
neither receipt nor possession thereo! conters ortranglers any right in, or fcense to use. the subject matter ol the deawing oF ary design oF technical thereon. nor 2ny right to reproduce this theteol. except for manutaeture by vena: Ten icense. no rightto reproduce this dr the subject matter thereof unless by swath or written permission trom the co:
(7)> SEA. RED.
009767-01
Figure 5-9 Control Panel Assembly
i Figure 5-9 Control Panel Assembly ATARI’
Part Number Description
009767-01 A030118-01 A007547-02 001856-01 62-002 75~5116B 75-010S 75-040 A030115-01 Control Panel with Graphics Switch Assy - See Figure 5-10 Shift Assy - See Figure 5-11 Bushing, Alun. Switch, LED, Lighted Carriage Bolt, #10-24 x 1.00 Lg (Black) #10 Washer, Flat #10 Washer, Split-Lock Control Panel Harness WOIDHRYNE POOORRPHEH
© A warner Communications Company
NOTICE TO ALL PERSONS RECEIVING THIS ORAWING CONFIDENTIAL: Reproduction forbidden without the specitic written permission of Atari. Inc.. Sunnyvale California. This arawieg 1s only conditionally issues. and either receipt nor possession inereot conters or transters, any right in. or licanse to use. the subject matter of the ‘drawing or any design of technica intormation shown, thereon. nor any right lo reproduce this drawing or any part thereo!, except for manufacture by vendors of Atari incor Porated and for manulacture under the corporation's written license. no rightto reproduce thisdrawing is granted or the subject matter thereof unless by written agreement with or written permission from the corporation,
Figure 5-10 Switch Assembly
Figure 5-10 Switch Assembly
Part Number
030116-01 030117-01 73-830 *65-081A 72-1410 75-054 75-9145 75-918S 75-028S 75-048 75-015S 19-9011
© warmer Communications Company PRPENNNNNNEBBEH Description
MTG Plate Flat Spring Knob Micro Switch* Machine Screw 4-40 x .62 La. Lock Washer Int. Tooth #4 Hex Nut #4-40 Hex Nut #8-32 Flat Washer #8 Split Lock Washer #8 Flat Washer #% Wide Pot 5K, Slip Clutch
- Acceptable Substitutes 65-091A, 65-101A, 65-11A, 65-041¢c
NOTICE TO ALL PERSONS RECEIVING THIS ORAWING CONFIDENTIAL. Reproduction forbidden without ine specific writien permission of Atari, Inc. Sunnyvale Califoraia. This drawing 1s only conditionally issued. and neither receipt nor possession iherec! confers or transfers any right 19. or license to use. the subject matter of the drawing or any design or technical information shown thereon, nor any right to reproduce this drawing crany part nereo! excep! far manulacture by vendors of Alar lNcorporated and for manulacture under the corporation's writ fenlicense, no right toeproduce this drawings granted or the subject matter thereo! uniess by wntten agreement with or written permission fom the Corporation.
ic
‘53 neao
Figure 5-11 ) 2 ReaD
Shift Assembly
I\ Figure 5-11 Shift Assembly ATARI
| Item | Part Number | Qty. | Description |
| L | A007480-01 | 1 | Shaft Assy |
| 2 | A007534-01 | 1 | Switch/Bracket Assy |
| 3 | A007188-01 | 1 | Shift Bracket Weldment |
| 4 | 007396-01 | 1 | Plate Slider |
| 5 | 007535-01 | 3 | Retainer, Compression |
| 6 | 007373-01 | 1 | Shaft |
| 7 | 007372-01 | 1 | Spring Pin |
| 8 | 75-014 | 2 | Flat Washer #4 |
| 9 | 75-2804S | 2 | Machine Screw 8-32 x 4" Lg. |
| 10 | 75-048 | 2 | Split Lock Washer #8 |
| 11 | 73-3002 | 2 | Retaining Ring #23-2 |
| 12 | 78-3001025 | 1 | Spring (LEE #LE-D45D-4) |
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Cut along this line
TM-106 1st printing
YOUR COMMENTS, PLEASE!
Your comments will assist Atari in improving the usefulness of our publications. They are an important part of preparing for revisions of manuals and parts catalogs. No post age stamp is necessary if mailed in the U.S.A. If you have any technical questions about certain Atari or Kee Games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.
Page: Comments:
Fill in if you wish a reply:
Name Firm O Distributor C1 Operator Address C1) Other -
City State Zip
First Fold
First Class Permit #1004 Sunnyvale, CA
Atari, Inc. P.O. Box 9027 Sunnyvale, California 94086
Attn.: Publications Group, Coin-Op Engineering
Second Fold
98076 VO ‘ajeaduuns 2206 XO “O'd “OUy ‘ery
abpy siy1 edey meee Ee ee HE EE EE EE
Cut along this line
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
ATARI INC 1265 BORREGAS AVENUE P.O. BOX 9027 SUNNYVALE, CALIFORNIA 94086