CATHODE RAY TOMES

Jambo Safari STD 2nd Printing

Jambo! Safari (Rev A) (Sega, 1999) · Manual · 82 pages · 79 sections · original scan

Page 1

STD VERSION

OWNER’S MANUAL

SEGA ENTERPRISES, INC. USA

MANUAL NO. 999-0886

Page 2

Warranty

Your new Sega Product is covered for a period of 90 days from the date of shipment. This certifies that the Printed Circuit Boards, Power Supplies and Monitor are to be free of defects in workmanship or materials under normal operating conditions. This also certifies that all Interactive Control Assemblies are to be free from defects in workmanship and materials under normal operating conditions. No other product in this machine is hereby covered.

Sellers sole liability in the event a warranted part described above fails shall be, at its option, to replace or repair the defective part during the warranty period. For Warranty claims, contact your Sega Distributor.

Should the Seller determine, by inspection that the product was caused by Accident, Misuse, Neglect, Alteration, Improper Repair, Installation or Testing, the warranty offered will be null and void.

Under no circumstances is the Seller responsible for any loss of profits, loss of use, or other damages.

This shall be the exclusive written Warranty of the original purchaser expressed in lieu of all other warranties expressed or implied. Under no circumstance shall it extend beyond the period of time listed above.

Page 3

TABLE OF CONTENTS

INTRODUCTION OF THE OWNERS MANUAL GENERAL PRECAUTIONS ADUNRWN—

8.

9.

10. . PRECAUTIONS TO BE HEEDED FOR OPERATION . NAME OF PARTS . ACCESSORIES . ASSEMBLY AND INSTALLATION . PRECAUTIONS TO BE HEEDED WHEN MOVING MACHINE . CONTENTS OF GAME . EXPLANATION OF TEST AND DATA DISPLAY 7-1 SWITCH UNIT AND COIN METER 7-2. SYSTEM TEST MODE 7-3 GAME TEST MODE 7-4 INPUT TEST 7-5 OUTPUT TEST 7-6 SOUND TEST 7-7 C.R.T. TEST 7-8 VOLUME SETTING 7-9 GAME ASSIGNMENTS 7-10 COIN ASSIGNMENTS

7-12 BACKUP DATA CLEAR HANDLE MECHA 8-1 REMOVING THE CONTROL PANEL 8-2 REPLACING AND ADJUSTING THE HANDLE’S VR 8-3 GREASING SHIFT LEVER 9-1 REMOVING THE SHIFT LEVER 9-2. SWITCH REPLACEMENT ACCEL & BRAKE 10-1 ADJUSTING AND REPLACING THE VR 10-2 GREASING TO FOOT BRAKE AND ACCEL . COIN SELECTOR . MONITOR . REPLACEMENT OF FLUORESCENT LAMP. 13-1 REPLACEMENT OF FLUORESCENT LAMP . PERIODIC INSPECTION TABLE . TROUBLESHOOTING . GAME BOARD 16-1 REMOVING THE GAME BOARD 16-2 REPLACMENT OF FUSE 16-3 COMPOSITION OF THE GAME BOARD . DESIGN RELATED PARTS . PARTS LIST . WIRING DIAGRAMS

Page 4

SPECIFICATIONS

Installation space: 68 in.(L) x 41 in. (W)

Height: 84 in.

Weight: Approx. 550 lbs.

Power maximum current: 3.5 Amp AC 120V 60 Hz

MONITOR: 29" NANAO MONITOR

INTRODUCTION OF THE OWNERS MANUAL

SEGA ENTERPRISES, LTD., has for more than 30 years been supplying various innovative and popular amusement products to the world market. This Owners Manual is intended to provide detailed descriptions together with all the necessary installation, game settings and parts ordering information related to JAMBO SAFARI STD, a new SEGA product.

This manual is intended for those who have knowledge of electricity and technical expertise, especially in ICs, CRTs, microprocessors, and circuit boards. Read this manual carefully to acquire sufficient knowledge before working on the machine. Should there be a malfunction, non-technical personnel should under no circumstances touch the interior system. Should the need arise, contact our main office, or the closest branch office listed below.

SEGA ENTERPRISES, INC. (USA) Customer Service 45133 Industrial Drive Fremont, CA 94538 Phone 415.701.6580 Fax 415.701.6594 7:30 am - 4:00 pm, Pacific Standard Time Monday thru Friday

Page 5

General Precautions

Follow Instructions: All operating and use instructions should be followed. Attachments: Do not use attachments not recommended by the product manufacturer as they may cause hazards. Accessories: Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use only mounting accessories recommended by the manufacturer. Moving the Product: This product should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product to overturn. Ventilation: Slots and openings in the cabinet are provided for ventilation, to ensure reliable operation of the product and to protect it from overheating; these openings must not be blocked or covered. The openings should never be blocked by placing the product in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

Power Sources: This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your location, consult your local power company. For products intended to operate from battery power or other sources, refer to the operating instructions. Grounding or Polarization: This product is equipped with a three-wire grounding-type plug, a plug having a third (grounding) pin. This plug will only fit into a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug. Power Cord Protection: Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product. Overloading: Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.

Object and Liquid Entry: Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product. Servicing: Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. Damage Requiring Service: Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:

  • If the power cord or plug is damaged;
  • If liquid has been spilled, or objects have fallen into the product;
  • If the product has been exposed to rain or water;
  • If the product does not operate normally when following the operating instructions. Adjust only those controls that are explained in the operating instructions. An improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation;
  • If the product has been dropped or damaged in any way;
  • When the product exhibits a distinct change in performance; this indicates a need for service. Replacement Parts: When replacement parts are required, be sure the service technician has used replacements parts specified by the manufacturer or that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.
Page 6

Safety Check: Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. Heat: The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat. Lithium Battery- Dispose of batteries only in accordance with the battery manufacturer’ s recommendations. Do not dispose in an open flame condition, since the battery may explode. Cleaning: When cleaning the monitor glass, use water or glass cleaner and a soft cloth. Do not apply chemicals such as benzine, thinner, etc. Location: This an indoor game machine, DO NOT install it outside. To ensure proper usage, avoid installing indoors in the places mentioned below: ¢ Places subject to rain/water leakage, or condensation due to humidity; + In close proximity to a potential wet area;

  • Locations receiving direct sunlight;
  • Places close to heating units or hot air; eIn the vicinity of highly inflammable/volatile chemicals or hazardous matter;
  • On sloped surfaces; « In the vicinity of emergency response facilities such as fire exits and fire extinguishers; + Places subject to any type of violent impact; Dusty places.

INSTALLATION PRECAUTIONS ¢ Verify the amperage of the branch circuit outlet before plugging in the power plug. Do not overload the circuit.

+ Avoid using an extension cord. If one is required, use an extension cord of type SJT, 16/3 AWG rated min. 120 VAC, 7A.

  • Moving this unit requires a minimum clearance (of doors, etc.) of 32” (W) by 77” (H). + For the operation of this machine, secure a minimum area of 32” (W) by 42”(D).

REGULATORY APPROVALS This game has been tested and found to comply with the Federal Communications Commission Rules. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This game has been tested and listed by Underwriters Laboratories, Inc., to ANSI/UL22.

LISTED

5K92

AMUSEMENT MACHINE

Page 7
  • PRECAUTIONS TO BE HEEDED FOR OPERATION

In order to prevent accidents, be sure to comply with the following points before and during operation.

PRECAUTIONS TO BE HEEDED FOR OPERATION BEFORE STARTING THE OPERATION

@ In order to avoid accidents, check the following before starting the operation: Check if all of the adjusters are in contact with the surface. If they are not, the cabinet can move and cause an accident.

WARNING!

ensure contact with floor

Do not climb on the product. Climbing on the product can cause falling down accidents. To check the top portion of the product, use a step. @ To avoid electric shock, check to see if door & cover parts are closed.

@ To avoid electric shock, short circuit and or parts damage, do not put the following items on or in the periphery of the product:

Flower vases, flower pots, cups, water tanks, cosmetics, and receptacles/ containers/vessels containing chemicals and water.

To avoid injury, be sure to provide sufficient space by considering the potentially crowded situation at the installation location. Insufficient installation space can cause the player to come into contact with or hit others

CAUTION! and result in injury or trouble.
Page 8

PRECAUTIONS TO BE HEEDED DURING OPERATION

CAUTION!
CAUTION! To avoid injury and accidents, those who fall under the following catagories are not allowed to play the game:
  • Intoxicated persons
  • Those who have high blood pressure or heart problems.
  • Those who have experienced muscle convulsion or loss of consciousness when playing video games, etc.
  • Persons susceptible to motion sickness.
  • Persons whose acts runs counter to the products warning displays.
  • Instruct those who wear high-heeled shoes to refrain from playing the game by explaining that playing the game with highheeled shoes is very dangerous and likely to cause a potentially hazardous situation.

To avoid electric shock and short circuit, do not allow customers to put hands and fingers or extraneous matter in openings of the product or small openings in or around doors. To avoid electric shock and short circuit, do not allow the customers to unplug the power plug without a justifiable reason. Although this product has the accident preventive covering attached to potentially hazardous places where hand and fingers could be caught, small children are unable to perceive hazards. Use care so that small children do not come close to the product when in play. Immediately stop such violent acts as hitting and kicking the product. Such violent acts can cause parts damage and/or falling down, resulting in injury due to fragments and falling down.

Page 9
  • NAME OF PARTS

JAMBO SAFARI STD

BILLBOARD

CONTROL PANEL.

COIN CHUTE TOWER

SEAT

GAME SPECIFICATIONS WIDTH in. LENGTH in. HEIGHT in. WEIGHT Ibs.

All measurements are and rounded UP

DURING SHIPPING 45” x 70” xX 84” ~ 600 LBS.

WHEN ASSEMBLED 39” xX 65” Xx 80” 550 LBS.

Page 10
  • ACCESSORIES

DESCRIPTION OWNERS MANUAL

Part No. (Qty.) 999-0886

Note

Figures

If Part No. has no description, the Number has not been registered or can not be registered. Such a part may not be obtainable even if the customer desires to purchase it. Therefore, ensure that the part is in safekeeping with you.

TAMPERPROOF WRENCH M8 540-0009-01 (1) TOOL KEY MASTER 220-5576 (2) For opening/closing the doors

a Os Or ees ia 200 wa KEY (2) For the CASHBOX DOOR

Page 11

THE SHIPMENT METHOD DESCRIBED BELOW ONLY APPLIES TO ‘MODEL 3’ BOARDS CONTAINED IN THE

WARNING! FOLLOWING GAMES:

LOST WORLD, VIRTUA FIGHTER 3, SUPER GT, SEGA BASS FISHING, STRIKER 2 HARLEY DAVIDSON, RALLY 2, DAYTONA 2, DIRT DEVILS, HOUSE OF THE DEAD 2, OCEAN HUNTER, STAR WARS TRILOGY, ZOMBIE REVENGE, CRAZY TAXI, MAJOR LEAGUE BASEBALL, VIRTUA TENNIS, JAMBO SAFARI !!NEVER SHIP MODEL 3 / NAOMI GAME

BOARDS OUTSIDE OF CAGE!!

CARTON BOX 601-8928 (1) Used for transporting the GAME BOARD. {SUPPLIED WITH YOUR GAME}

DO NOT SHIP GAME BOARD WITHOUT THIS BOX AS IT MAY DAMAGE THE GAME BOARD AND VOID YOUR WARRANTY.

“CHECK SIDE” Display

FILTER BOARD

NO OTHER GAMES BOARDS ARE TO BE SHIPPED IN THE CAGE AS THEY MAY BE DAMAGED BEYOND REPAIR. PLEASE SHIP THEM WITHOUT CAGE PROPERLY PROTECTED DURING SHIPPING.

WARNING!
Page 12
  • ASSEMBLING AND INSTALLATION

A

CAUTION! Assembling should be performed as per this manual. Since this is a complex machine, erroneous assembling may cause damage to the machine, or malfunctioning to occur. When assembling, be sure to perform work by plural persons. Depending on the assembly work, there are some cases in which performing the work by a single person can cause personal injury or parts damage.

When carrying out the assembly work, follow the procedure in the following 5-item sequence:

A

CAUTION! 1 | ASSY OF THE REAR CABI (COCKPIT)

ASSY OF BILLBOARD

SECURING IN PLACE (ADJUSTER ADJUSTMENT)

4 | POWER SUPPLY

ASSEMBLING CHECK

1 ASSY OF REAR CABI (COCKPIT)

ote that the tools such as a phillips screwdriver and wrench for M16 hexagon bolt w/24 mm width across flats are required for the assembly work.

Permanantly tightening the hex bolts should not be completed until the leg levelers are adjusted properly.

POWER CORD

Page 13

® Install the coin chute tower on the Right-hand side of cabinet. Open the coin chute door and the cashbox door to secure with the 4 hexagon bolts from inside the doors. Please note that the Coin Chute tower is NOT mounted

COIN CHUTE DOOR

COIN CHUTE TOWER

FLAT WASHER HEXAGON BOLT (4} M& X20

NOTE: ON SEGA’s CRAZY TAXI GAME THERE IS NOT TWO COCKPITS SIDE BY SIDE AS PICTURED ABOVE. THE GAME HAS ONLY ONE COCKPIT AND THE COIN TOWER WILL MOUNT ON THE RIGHT SIDE AS YOU FACE THE CABINET..
Page 14

2 ASSY OF THE BILLBOARD

Due to its large size, it is very difficult for one person alone to install the billboard, Make sure 2 or more persons are available to perform this work. Attempting to perform the installation alone can cause an accident.

WARNING!

® Mount Billboard on cabinet by ensuring the front lip of the Billboard is securely placed under the mounting bracket already installed on the cabinet. Fasten with the 3 hexagon bolts.

@) Connect all of the 4 connectors inside the Billboard box (This needs to be done prior to final installation of Billboard Assy).

™t+-——__ HEXAGON BOLT(black) (4EA)

BILLBOARD HOLDER

HEXAGON BOLT(black) (4)

BILLBOARD CASE

BILLBOARD’ s_ connector

Page 15
WARNING! SECURING IN PLACE (ADJUSTER ADJUSTMENT)

Be sure to have all the Adjusters make contact with the surface. Unless the Adjusters come into contact with the surface, the Cabinet can move of itself, causing an accident.

This machine has 4 each of casters and adjusters (shown below). When the installation position is determined, cause the adjusters to come into contact with the floor directly, make adjustments in a manner so that the casters will be raised approximately 5mm. from the floor and make sure that the machine position is level.

  • Move the machine to the installation position.

o) Move the machine to the installation position @ Cause all of the leg levelers to make contact

with the floor. By using a wrench, make adjustments in the height of the leg adjusters to ensure that the machine's position is level. \ Leg Leveler

QB) After making adjustments, fasten the leg Leg Leveler

adjuster nut upward and secure the height of the leg adjuster.

Page 16

4 | power SUPPLY

@ Ensure that the power cord is not exposed on the surface (passage, etc.). If exposed, they can be caught and are susceptible to damage. If damaged, the cord can cause an electric shock or short circuit. @ Ensure that the wiring position is not in the customer's passage way

WARNING! or the wiring has protective covering.

Connect the game to the power supply and turn on power to the game. Before connecting power supply be sure that power switch is off

MAIN SW

@ Turning the AC unit’s main switch on will cause the machine Q In the Power On check, the steering wheel turns left and right,

to start the power check and network check automatically.

and then returns to the centering position and stops. In this check, the values of the VR inside the control panel are corrected.

G3) Until this check is finished, and the steering wheel stops, do

not touch the steering wheel or play the game.

If you do, the steering reaction during the game (reaction at the time of course-out or crash) can not be obtained correctly. In the case of an abnormal reaction during the game, turn power on again from the beginning and complete the power on check.

To the Power Supply Socket outlet

Page 17

ASSEMBLING CHECK

The TEST MENU allows for each part of the cabinet to be checked, the Monitor to be adjusted, and the coin and game

related various functions to be performed.

Selecting the MEMORY TEST on the test mode menu screen causes the on-board memory to be tested automatically. The game board is satisfactory if the display beside each IC No. shows GOOD.

MENU MODE

SYSTEM MENU

RAM TEST JVS TEST SOUND TEST C.R.T. TEST SYSTEM ASSIGNMENTS COIN ASSIGNMENTS: BOOKKEEPING BACKUP DATA CLEAR. CLOCK SETTING

ROM BOARD TEST > GAME TEST MODE (XXXXX KKK KKK]

EXIT SELECT WITH SERVICE BUTTON AND. PRESS TEST BUTTON VOLUME SETTING BOOKKEEPING BACKUP DATA CLEAR CRAZY TAX! TEST MENU

INPUT TEST OUTPUT TEST SOUND TEST GAME ASSIGNMENTS

~> EXIT

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

SYSTEM TEST MODE MENU

INPUT TEST

ORIVE GEAR OFF REVERSE GEAR OFF START OFF COIN CHUTE #1 OFF COIN CHUTE #2 OFF SERVICE OFF TEST OFF HANDLE 80H ACCEL 30H BRAKE 30H

PRESS TEST AND SERVICE BUTTON TO EXIT

OUTPUT TEST

START LAMP. ON

PRESS TEST BUTTON TO EXIT GAME TEST MODE MENU

Selecting the INPUT TEST on the Test Mode menu screen causes the screen (on Which each switch adnV.R. are tested) to be displayed. Press each switch. For the coin switch test, insert a coin from the coin inlet with the coin chute door

being open. If the display beside each switch indicates “ON”, the switch and wiring connections are satisfactory. Check the display of V.R. value for steering wheel and accelerator & brake. If the V.R. values are not satisfactory, make adjustments as neccesary.

In the OUTPUT TEST mode, carry out lamp test to ensure that each lamp lights up satisfactory.

Page 18

SOUND TEST

Voice

EFFECT

BGM.

>EXIT

SELECT WITH SERVICE BUTTON AND. PRESS TEST BUTTON TO EXIT

CRTTEST 12

WHITE WM oe

PRESS TEST BUTTON TO CONTINUE In the TEST mode, selecting SOUND TEST causes the screen, on which sound related BD and wiring connections are tested, to be displayed. Be sure to check if the sound is satisfactorily emitted from each of speaker and the sound volume is appropriate.

In the TEST mode menu, selecting C.R.T. TEST allows the screen (on which the projector is tested) to be displayed. Although the projector adjustments have been made at the same time of shipment from the factory, color deviation, etc., may occur due to the effect caused by geomagnitism, the location building’s steel frames and other game machines in the periphery. By watching the test mode screen, make judgement as to whether an adjustment is needed. If it is neccessary, adjust the projector by refering to Section 9.

Perform the above inspections also at the time of monthly inspection.

Page 19
  • PRECATIONS TO BE HEEDED WHEN MOVING THE MACHINE

@ When moving the machine, be sure to pull out the plug from the power supply. Moving the machine with the plug as is

WARNING! inserted can damage the power cord and cause a fire or electric shock. @ When moving the machine on the floor, retract the Adjusters and ensure that Casters make contact with the floor. During transportation, pay careful attention so that Casters do not tread power cords. Damaging the power cords can cause an electric shock and/or short circuit. @ When lifting the cabinet, be sure to hold the catch portions or bottom part. Lifting the cabinet by holding other portions can damage parts and installation portions, due to the empty weight of the cabinet, and cause personal injury.

Use care when handling glass made parts. When the glass is damaged, fragments of glass can cause injury

CAUTION!

Do not push the

cabinet from the left/right direction.

Page 20
  • CONTENTS OF GAME

The following explanations apply to the case the product is functioning satisfactorily. Should there be any moves different from the following contents, some sort of faults may have occured. Immediately look into the cause of the fault and eliminate the cause thereof to ensure satisfactory operation. During the Advertise mode, the Billboard’s Decoration Lamp lights up periodically. When the machine is energized, the Billboard’s Fluorescent Lamp is always lit. The Steering Wheel repeats centering action periodically. Automatic centering will apply to the Steering Wheel if it is not centered. During the Advertise Mode, sound is emitted from the Speaker beside the Monitor.

OUTLINE OF GAME

The player as a ranger that captures wild animals in Africa for investigation rides in a jeep and captures animals witha rope and net. Capturing an animal increases the ranger point (displayed on the upper left screen) and the time.

Divided into 6 investigation areas, the various kinds of animals to capture as the norm set for the player (displayed on the upper center) and ther time limit (displayed on the upper right) are provided in each area. When the player fullfills the above norm within the time limit, the investigation in that area is finished and he/she can proceed to the next area. Finishing the investigation in all areas results in clearing the game. When the time limit becomes zero, the game is over.

HOW TO OPERATE

The operation of Steering Wheel, and Accelerator & Brake Pedals is similar to the actual car.

ROPE/NET LEVER: Throw a rope with the monitor (the rear) side input and cast a net when the animal is caught by the rope. Draw in the rope passed around with the front side input unit.

STEERING WHEEL Pea

1K) (aa)

5 °

START BUTTON

BRAKE PEDAL ~~ ACCELERATOR PEDAL.

Page 21

HOW TO PLAY

oO) Insert a coin. Coin insertion causes credit(s) to be displayed on the screen. For example, in the case of 2 coins one credits setting, “INSERT MORE COIN(S) CREDIT(S) 1/2” is displayed when one coin is inserted.

® Inserting one play worht of coin(s) causes “PRESS START BUTTON” to be displayed and START button to flash. Press START button to have the Mode Select Screen appear on the monitor.

@ Select the play mode from either BEGINNER or EXPERT Mode in the Mode Select Screen. BEGINNER mode consisits of 2 areas. In this mode, “instructions” is given during the game play. BEGINNER Mode is suitable for those who first play this game. EXPERT Mode consists of 4 areas, and is suitable for those who have played this game before. “Instructions” is not given during the game in the EXPERT Mode.

To select the mode, turn ther Steering Wheel left or right to shift the frame attached to the mode. Step on the Acelerator Pedal to decide on the mode with the frame being attached.

While the Mode Select is displayed, countdown is executed. Counting down to 0 causes the mode with frame being attached to be selected automatically.

In case BEGINNER is selected, the monitor proceeds tothe confirmation screen and the play mode to be selected again. Deciding the play mode causes the Character Select Screen to appear.

® In the Character Select Mode, select on-screen player character. Turn the Steering Wheel left or right to shift each character. Press START button or step on the Accelerator Pedal to decide on the character being displayed.

While the Character Select Mode is displayed, countdown is executed. Counting down to 0 causes the character being displayed to be selected automatically. Character ability is identical.

  • When the character is determined, the game starts. By driving the jeep, move on the field and look for the animal you wish to catch. When you find the animal to aim at, approach to the animal until sight is appeared on the monitor and throw a rope by inclining the lever to the back. Zero-in on the animal unit] the rope captures the animal.

SERCHING FOR ANIMALS SCREEN. CAGES. The acinals are classified RANCER POIKT and taken te Une cage Gane Score. TIM_Let Renaining Tine

SiG Direction the rope and the net are thrown to.

DRIFT TURN =

WANE OF_CORIAND Sinultaneously displayed when the command is executed by the player.

Page 22

© When the rope is passed around the animal, pull the rope by inclingin the Lever towards you and approach the animal.

Time is increased by at least onesecond each time the player get s the ring attached to the rope. When the rope flashes red and the tension gauge displays “ATTENTION”, release the Lever to loosen the rope. Otherwise the rope will be broken.

@ Throw the net over the animal. When the player’s view changes and the screen displays the sight, throw the net by inclining the Lever backward. Zero-in on the animal unit! the animal is captured by the net with the net. When the player succeeds to capture the animal without spending much time, the on-screen replay scene of capturing the animal is displayed.

GRAPPLING MODE

The Distance Ncter TENSION GAUGE The Distance to the animal The rope's tension.

RANGER TIME

POINTS coceo 50 FACE JOON Expresses the animal's condition.

® When the animal is captured, the on-screen image changes to the evaluation mode. Operation is not allowed during this time.

In the evaluation mode, the animals are taken into the cage after the dsescriptions and the rank (number of *) of animals captured, the time earned, and the points earned are displayed. The evaluation is based on the rank of ther animals the playeer captured. The higher the rank, the more time and points the player can earn. However, capturing the identical animals decreases the amount of time and points the player casn earn

EVALUATION MODE

POINTS: coven 50

DESCRIPTION

RANK

TIME BONUS

Page 23

® Upon completion of the Evaluation Mode, the monitor shifts to the Binoculars Mode. In the Binoculars Mode, various kinds of animals around the player and the distance to the animals are shown. In this mode, when the Steering Wheel is turned, the view point is also shifted to the same direction. Step on the Accelerator pedal whe the animal aimed at appears, and the screen shifts to the Searching for animals mode from thr Binoculars Mode and displays the arrow pointing to the animal on the ground.

The time limit counts down more slowly while the Binoculars mode is displayed

BINOCULARS MODE RANK OF ANIMAL DISPLAYED NO.of colored stars.

DISTANCE NEW 1 : Distance to the pererererarsg ture i animal displayed. FINISHED) 7

IDENTIFIED OR UNIDENTIFIED NEW: Unidentified FINISHED: Identified

@ After finishing the investigation, the screen shifts to the Report of Investigation Mode. The toal point and the rank intechnique are displayed in this mode.

TOTAL POINT: The sum of the points that the player has earned so far and that the remaining time in the area is converted to .

TECHNICAL LEVEL: Levels in accordance with the TOTAL POINT.

@ When the time limit becomes zero, the game is over. Total Level, Total Point, and the Total Ranking are displayed. The Total Ranking is the point ranking based on the data of 99 players who have played the game on the machine. then the screen proceeds to the “GAME OVER” screen. If any credit(s) which is one play worth or more remians, the START LAMP unlit during the game will then flash.

Page 24

KNACK OF PLAY

® Always keep the animal on the center of the screen when drawing in the rope. If you operate the Steering Wheel keeping the this in mind, you can smoothly get close to the animal.

@ Don’t chase the animal too far. If it seems to take too much time to ge the animal you aim at, change to the animal of lower rank. Know your technical level and pay attention to the time.

(©) Use Commands. DASH: With the Steering Wheel in the centering position, quickly step on the Accelerator pedal twice. Speed can be greatly increased for a while. Effective for getting close to animals who run fast or who are away from here.

DRIFT: Turn the Steering Wheel to the direction you wish and step on the Accelerator Pedal again. This increases the turning ability without reducing speed. Efective for getting animals who have high turning ability.

Page 25
  • EXPLANATION OF TEST AND DATA DISPLAY

By operating the switch unit, periodically perform the tests and data check. When installing the machine initially or collecting cash, or when the machine does not function correctly, perform checking in accordance with the explanations given in this section. The following shows tests and modes that should be utilized as applicable.

=

IMPORTANT! CAUTIONS TO BE HEEDED WHEN USING THE TEST MODE: In the case where plural machines are linked for communication play, if even one seat enters the test mode, all of the linked seats will enter the test mode. Therefore, if any one of the linked machines is in play, use care so as not to use the test mode. The contents of the setting changes made will not be effective unless the test mode is finished in the test mode. When the setting is changed, be sure to “EXIT” in the menu mode. Do not press the TEST BUTTON during network check at the time of turning the power on or exiting from the test mode. If anyone of the linked machines uses the test mode during network check, all other Seats will continue network checking. Cause all of the Seats to reenter the test mode and then have all of the Seats exit from the test mode simultaneously.

TABLE 7 EXPLANATION OF TEST MODE

ITEMS DESCRIPTION SECTIONS

When the machine is installed, perform the following:

INSTALLATION|1. Check to see that each setting is as per standard setting made7-10, 7-11

OF MACHINE at the time of shipment. 1-6

  • In the INPUT TEST mode, check each SW and VR. 7-7
  • In the OUTPUT TEST mode, check each of lamps. 7-3,7-4
  • In the MEMORY TEST mode, check ICs on the IC Board.

Choose MEMORY TEST in the MENU mode to allow the

MEMORYMEMORY test to be performed. In this test, PROGRAM7-3,7-4

RAMs, ROMs, and ICs on the IC Board are checked.

PPeriodically perform the following:7-10,7 -I
  • MEMORY TEST
  • Ascertain each setting. 7-6
  • In the INPUT TEST mode, test the CONTROL device
  • In the OUTPUT TEST mode, check each of lamps. 7-7
CONTROL1. In the INPUT TEST mode, check each SW and VR.71-6

SYSTEM 2. Adjust or replace each SW and VR.

  • If the problem can not be solved yet, check the CONTROL’s moves.) 8

MONITOR In the MONITOR ADJUSTMENT mode, check to see if the 12

MONITOR adjustment is appropriately made.

IC BOARD1. MEMORY TESTT2
  • In the SOUND TEST mode, check the sound related ROMs. 7-8
DATA CHECK{Check such data as game play time and histogram to adjust the7-15

difficulty level, etc

Page 26

7-1 SWITCH UNIT AND COIN METER

Never touch places other than those specified. Touching places not specified can cause electric shock and short circuit.

@ Adjust to the optimum sound volume by considering the environmental requirements of the installation location. @ |f the COIN METER and the game board are electrically disconnected,

IMPORTANT! game play is not possible.

Open COIN CHUTE DOOR, and the switch unit shown appears. The function of each switch is as follows:

SWITCH UNIT

() SOUND VOLUME

Controls the speaker volume of the right/left speakers.

(2) TEST BUTTON (TEST SW)

For the handling of the TEST BUTTON, refer to the section on test mode.

(3) SERVICE BUTTON (SERVICE SW)

Gives credits without registering on the coin meter.

SOUND VOLUME

COIN METER

SQUND VOLUME

© CE) DEMAGNETIZER SWITCH

SERVICE BUTTON,

Page 27

7-2 SYSTEM TEST MODE

The contents of setings chnaged in the TEST mode are stored when the TEST mode is finished from EXIT in the MENU mode. If the power is turned off before the TEST

mode is finished, the contents of setting chnage become ineffective. Executing “BACKUP DATA CLEAR” in the SYSTEM TEST MODE does not clear the

IMPORTANT! BOOKKEEPING data in the GAME TEST MODE.

Entering the TEST mode clears fractional number of coins less than one credit and BONUS ADDER data.

The SYSTEM TEST mode mainly allows for IC Board functioning check, monitor adjustment, coin assignments, etc. For details, refer to NAOMI SERVICE MANUAL. The following assignments, however, should be designated for this product. CABINET TYPE: 1 PLAYER (S)

MONITOR TYPE: HORIZONTAL

COIN CHUTE TYPE: COMMON

7-3 GAME TEST MODE

SYSTEM MENU JAMBO SAFARITEST MENU

RAMTEST IVS TEST PUT TES! SOUND Test OurPUT Test CRITEST SOUND TEST SYSTEM ASSIGNMENTS GAME ASSIGNMENTS COIN ASSIGNMENTS VOLUME SETTING

BOOKKEEPING BOOKKEEPING

BACK UP DATA CLEAR BACK UP DATA CLEAR

CLOCK SETTING

SEXIT ROM BOARD TEST >GAME TEST MODE,

EXIT

SELECT WITH SERVICE BUTON SELECT WITH SERVICE BUTTON See AND PRESS TEST BUTTON TO EXIT

+ Press the TEST button to display the SYSTEM TEST MODE MENU. By pressing the SERVICE button, move the arrow (->) to select the GAME TEST MODE. + Press the TEST button to enter GAME TEST MODE. The screen displays the GAME TEST MODE MENU. + By pressing the SERVICE button, move the arrow (->) to select the desired item. Press the TEST button to execute the selected item.

+ Select EXIT and press the TEST button to exit from the GAME TEST MODE and return to the SYSTEM TEST

MODE MENU. Further, select EXIT and press the TEST button to finish SYSTEM TEST MODE and return to the

normal mode.

Page 28

7-4 INPUT TEST Select INPUT TEST to have the screen shown below appear and to observe the status of each switch and the value of each V.R. on the Control Panel. Periodically check the status of each switch and V.R. on this screen.

INPUT TEST

COIN CHUTE #1 OFF

COIN CHUTE #2 OFF

SERVICE OFF TEST OFF START OFF LEVER UP OFF LEVER DOWN OFF HANDLE. oH

ACCEL, 30H

BRAKE 33H

PRESS TEST AND SERVICE BUTTON TO EXIT

FIG. 7.4 INPUT TEST

7-5 OUTPUT TEST

OUTPUT TEST

STARTLAMP OFF

>EXIT

PRESS TEST BUTTON TO EXIT

FIG. 7.5 OUTPUT TEST @ By pressing each switch, if the display on the right-hand side of the name of each switch changes to ON from OFF, the SW and the wiring connections are satisfactory.

To check CHUTE | & CHUTE 2 coin switches, open the COIN CHUTE DOOR and insert a coin(s) in the slot.

Press either the TEST BUTTON and the START BUTTON to return to the test menu.

As a standard, refer to the following for each of the Volume’s adjustment. By operating the Handle (Steering Wheel) and Pedal, if the V of each Volume guage smoothly moves as the corresponding value varies ina natural manner, then it is satisfactory.

Choose OUTPUT TEST to cause the following lower screen to appear. In this test, check the status of each lamp.

The right-hand side “ON” & “OFF” display of START LAMP automatically alternates. The lamp lights up when “ON” is displayed and goes off when “OFF” is displayed. Check to ensure that the lamp lights up and goes off in consistency with the display of “ON” and “OFF”.

Press the TEST button to return to the TEST MENU.

Page 29

7-6 SOUND TEST

SOUND TEST

BGM. os (SOUND STOP) EFFECT: 0/360 (SOUND STOP) Ics (SOUND STOP) >EXIT

SELECT WITH SERVICE BUTTON PRESS TEST BUTTON TO EXIT

FIG. 7.6 SOUND TEST

7-7 C.R.T. TEST

CRTTEST 12

Wiis oe

PRESS TEST BUTTON TO CONTINUE

PSPECEE St FIG. 7.7 C.R.T. TEST This test mode allows each sound related board and speaker to be checked.

e Press the Service Button to select the sound to be tested, and press the Test Button to have the selected Sound Test screen appear.

@ Select EXIT and press the Test Button to return to the Test Menu.

@ Select C.R.T. TEST to cause the MONITOR to display the screen shown left, allowing MONITOR adjustment status to be checked.

@ Periodically check the MONITOR adjustment status on this screen.

The screen (1/2) enables color adjustment check to be performed. The color bar of each of the 4 colors, i.e.,red, green, blue, and white, is the darkest at the extreme left and becomes brighter towards the extreme right.

Press the TEST BUTTON to shift to the next screen (2/2).

The screen (2/2) allows screen size and distortion to be tested.

Check if the CROSSHATCH FRAME LINE goes out of the screen and if the crosshatch lines are distorted.

Press the TEST BUTTON to return to the MENU mode.

Page 30

7-8 VOLUME SETTING

When VOLUME SETTING is selected, the following appears on the screen and each operating unit’s Volume can be

set.

If the operability is unsatisfactory, or when the Volume is adjusted or replaced, set the Volume in this mode.

The 3 kinds of Volume Settings for HANDLE, ACCEL, and BRAKE are to be set. The Max. value, Min. value for each

and the HANDLE’S CENTER value are to be set as applicable.

VOLUME SETTING

Press the SERVICE button to select the Volume value to be changed. HANDLE SETTING ADO:70H CENTER 7bH

LEFT MAX IaH <---> aH RIGHT MAX Press the TEST button to cause the characters of the

ACCEL SETTING AD1:30H

selected Volume value to turn red. MIN 31H <---> OH MAX

BRAKE SETTING AD2:38H. MIN 39H <.-->bcH MAX Input the value in the manner corresponding to the selected item. >EXIT © © © ©

Press the SERVICE buton to select EXIT, and press the TEST button to return to the MENU mode. At the same time the VOLUME SETTING is finished, the input values are stored as the Max. and Min. values.

ELECT WITH SERVICE BUTTON

RIG.19s8 VObUMEISETTING

Page 31

7-9 GAME ASSIGNMENTS

Selecting the GAME ASSIGNMENTS in the MENU mode causes the present game settings to be displayed and also the game settings changes (game difficulty, etc.) can be made. Each item displays the following content.

SETTING CHANGE PROCEDURE

@ Press the SERVICE BUTTON to move the “>” to the desired item. @) Choose the desired setting change item by using the TEST BUTTON. @ To return to the MENU mode, move the arrow to EXIT and press the TEST BUTTON.

GAME ASSIGNMENTS

START TIME (NORMAL) CONTINUE TIME (NORMAL) GET TIME DIFFICULTY (NORMAL) CABINET TYPE (sTD)

>EXIT

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON 10 EXIT @ START TIME This is the time alloted at the time of game start. Setting is possible starting from the shortest time sequentially in order of 35, 40, 45, 50, 55, -60, 65, and 70.

CONTINUE TIME Sets the time limit given when the game is continued. Select from among 5 levels, i.e. Very Easy, Easy, Normal, Hard, Very Hard.

GET TIME DIFFICULTY Sets the Bonus Time given when an animal is caught. Sets the difficulty level in 5 categories, i.e., WERY EASY, EASY, NORMAL, HARD, and HARDEST.

CABINET TYPE Setting of Cabinet. Set to STD

Page 32

7-10 COIN ASSIGNMENTS

The “COIN ASSIGNMENTS” mode permits you to set the start number of credits, as well as the basic numbers of coins and credits. This mode expresses “how many coins correspond to how many credits.”

SETTING CHANGE PROCEDURE

Gran Setting changes cannot be stored unless the TEST BUTTON is pressed

while the arrow is on EXIT.

PORTANT!

() Press the SERVICE BUTTON to move the arrow to the desired item.

@ Choose the desired setting change item by using the TEST BUTTON.

@ To return to the MENU mode, move the arrow to EXIT and press the TEST BUTTON.

7 - 10 COIN ASSIGNMENTS

COIN ASSIGNMENTS

COIN/CREDIT SETTING #1 CHUTE# = 1COIN. 1 CREDIT

CHUTEH2 COIN 1 CREDIT

ADDITIONAL SETTING MANUAL SETTING

>EXIT

SELECT WITH SERVICE BUTTON

AND PRESS TEST BUTTON

@ COINCREDIT SETTING Sets the CREDITS increase increment per coin insertion. There are 27 setings from #1 to #27, expressed in XX CREDIT as against XX COINS inserted. (TABLE 7.10a, 7.10b) #27 refers to FREE PLAY. ‘When the COIN CHUTE TYPE is set to INDIVIDUAL, there are some setting numbers not displayed as indicated in TABLE 7.10b.

MANUAL SETTING This allows credit increase setting as against coin insertion to be further set in the manner finer than COIN/CREDIT SETTING (refer to TABLE 7.10c).

Page 33

TABLE 7.10a COIN/CREDIT SETTING (COIN CHUTE COMMON TYPE)

SETTING FUNCTIONING OF CHUTE#1

SETTING #11 COIN1 CREDIT.
SETTING #21 COIN2 CREDITS
SETTING #31 COIN3 CREDITS
SETTING #41 COIN4 CREDITS
SETTING #51 COIN5 CREDITS
SETTING #61 COIN2 CREDITS
SETTING #71 COIN5 CREDITS
SETTING #81 COIN3 CREDITS
SETTING #91 COIN4 CREDITS
SETTING #101 COIN5 CREDITS
SETTING #111 COIN6 CREDITS
SETTING #122 COINS1 CREDIT.
SETTING #131 COIN1 CREDIT.
SETTING #141 COIN2 CREDITS
SETTING #151 COIN1 CREDIT

2 COINS 3 CREDITS

SETTING #161 COIN3 CREDITS
SETTING #173 COINS1 CREDIT.
SETTING #184 COINS1 CREDIT.
SETTING #191 COIN1 CREDIT

2 COINS 2 CREDITS 3 COINS 3 CREDITS 4 COINS 5 CREDITS

SETTING #201 COIN5 CREDITS
SETTING #215 COINS1 CREDIT.
SETTING #221 COIN2 CREDITS
SETTING #232 COINS1 CREDIT

4 COINS 2 CREDITS 5 COINS 3 CREDITS

SETTING #241 COIN3 CREDITS
SETTING #251 COIN1 CREDIT

2 COINS 2 CREDITS 3 COINS 3 CREDITS 4 COINS 4 CREDITS 5 COINS 6 CREDITS

SETTING #261 COIN1 CREDITS

SETTING #27 FREE PLAY

Page 34

MANUAL SETTING

COIN TO CREDIT

BONUS ADDER

cON 1 CREDIT 1

cON 1 CREDIT 1

>EXIT

COIN CHUTE #1 MULTIPLIER

  • COIN COUNTS AS 1 COIN

COIN CHUTE #2 MULTIPLIER 1 COIN COUNTS AS 1 COIN MANUAL SETTING

LOIN

NO BONUS ADDER -]

23456788
23456789
203456789
23456789

‘SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

FIG. 7.11b MANUAL SETTING

@ Determines Coin/Credit setting.

@ This sets how many coins should be inserted to obtain one Service Coin. Selecting MANUAL SETTING in the COIN ASSIGNMENTS mode displays the following screen.

ed ae)

@ This sets how many tokens one coin represents.

Table 7.10e MANUAL SETTING

COIN TO CREDIT 1 COIN 1 CREDIT 2 COINS 1 CREDIT 3 COINS 1 CREDIT 4 COINS 1 CREDIT 5 COINS 1 CREDIT 6 COINS 1 CREDIT 7 COINS 1 CREDIT 8 COINS 1 CREDIT 9 COINS 1 CREDIT

BONUS ADDER NO BONUS ADDER 2 COINS GIVE | EXTRA COIN 3 COINS GIVE | EXTRA COIN 4 COINS GIVE 1 EXTRA COIN 5 COINS GIVE 1 EXTRA COIN 6 COINS GIVE | EXTRA COIN 7 COINS GIVE | EXTRA COIN 8 COINS GIVE | EXTRA COIN 9 COINS GIVE | EXTRA COIN

COIN CHUTE MULTIPLIER 1 COIN COUNTS AS 1 COIN 1 COIN COUNTS AS 2 COINS 1 COIN COUNTS AS 3 COINS 1 COIN COUNTS AS 4 COINS 1 COIN COUNTS AS 5 COINS 1 COIN COUNTS AS 6 COINS 1 COIN COUNTS AS 7 COINS 1 COIN COUNTS AS 8 COINS 1 COIN COUNTS AS 9 COINS

Page 35

7 - 11 BOOKKEEPING Choosing BOOKKEEPING in the MENU mode displays the data of operating status up to the present are shown on 2 pages. Press the TEST BUTTON to proceed to PAGE 2/2.

NUMBER OF GAMES. Total number of plays. BOOKKEEPING TAGE e

@ NUMBER OF CONTINUE Total number of continues. NUMBER OF GAMES 0 NUMBER OF CONTINUE 0 AVERAGE PLAY 00H OOM 00s

In Page 2/3, Histogram of Number of Play as against Play Time is displayed. For setting the DIFFICULTY, refer to this histogram.

Page 3/3 displays Histogram of Number of Play as against Game Score. For setting the DIFFICULTY, refer to this histogram. PRESS TEST BUTTON TO CONTINUE

FIG. 7.11a BOOKKEEPING (1/3)

BOOKKEEPING PAGE 2/3 BOOKKEEPING 3/3,

TIME HISTOGRAM ‘ooMO0S~00MS9S 0 TOTAL SCORE HISTOGRAM

O1MO0S~O1MS9S0F19999fi
(2Mo0S~02MS9S0-399990
(03MO0S~03MS9S0-599899
05790990

° fio

(06MO0S~06M59S0ieee.
O7MO0S~O7MS9S0:1599990
O8MO0S~08MS9S0.1799990
(09MO0S~09MS9S021999990
1OMO0S~10MS9S0.2199990
0:2299990

L4Mo0S~14MS9S 0 OVER ~ 1SMO0S 0 ‘SELECT WITH SERVICE BUTTON PRESS TEST BUTTON TO EXIT

PRESS TEST BUTTON TO CONTINUE FIG. 7.11b BOOKKEEPING (2/3) FIG. 7.11¢c BOOKKEEPING (3/3)

7-12 BACKUP DATA CLEAR GAckUPDMAGIEAR Clears the contents of BOOKKEEPING and high : eS score player ranking entry.

oho Mace) @ = When clearing, bring the arrow to “YES” and when

not clearing, to “NO”, by using the SERVICE BUTTON, and push the TEST BUTTON.

@ = When the data has been cleared, “COMPLETED”

will be displayed. Bring the arrow to “NO” and press the TEST BUTTON to cause the MENU mode to return on to the screen.

@ Note that the contents of the GAME SETTING, SELECT WITH SERVICE BUTTON COIN SETTING, and BOARD SETTING are not passmsrnetetoess affected by BACKUP DATA CLEAR operation.

FIG. 7.12 BACKUP DATA CLEAR 32

Page 36
  • HANDLE MECHA

@ In order to prevent an electric shock and short circuit, be sure to turn power off before performing work by touching the interior parts of the product. @ Be careful so as not to damage wirings. Damaged wiring can cause an electric shock ‘ARNING! Wi al or short circuit accident.

In the test mode, if the steering wheel’s VR variations are not within the allowable range, the VR installation position adjustments or VR replacement is needed. Also, be sure to apply grease to the VR gear portion once every 3 months.

8-1 REMOVING THE CONTROL PANEL

® Turn the power switch off. @ Remove a total of 4 tamperproof screws from both sides of the control panel’s front.

  • Remove the two tamperproof screws fromthe underside of the control panel. ® Wiring connectors are connected inside the control panel. Carefully draw the control panel in a mnner so as not to damage wiring. ©) Disconnect the wiring connector.

TAMPERPROOF SCREW (black) (6) WS x 30

Page 37

8 - 2 REPLACING AND ADJUSTING THE HANDLE’S VR

@ Never touch places other than those specified. Touching places not specified can cause electric shock and/or short circuit.

WARNING! @ After the replacement or adjustment of the VR, be sure to set the variable value of . the VR in the test mode’s Volume Setting.

REPLACING THE VOLUME

® Turn off the power. @ Disconnect the connector.

  • Take out the 2 screws which secure the volume Bracket and remove the Volume Bracket. ©) Take out the 2 screws to remove the Volume Gear and replace the Volume.
  • After replacing the Volume, perform Volume setting in the Volume Setting Mode.

ADJUSTING THE VOLUME

® In the Test Mode, have the Volume value indicating screen displayed. @ Loosen the 2 screws which secure the Volume Bracket to disengage Gear Mesh. @ With the Steering Wheel in the centering position, cause gears to be engaged in the manner so that the Volume Shaft is in the status shown below. @® Fasten screws which secure the Volume Bracket. © Perform Volume setting as per the Volume Setting Mode.

cw (2) MIX8,w/flat & spring washers

VR_BRACKET a "D"CUT FACE

Page 38

8 - 3 GREASING

@ Never touch places other than those specified. Touching places not specified can cause electric shock and/or short circuit.

WARNING! @ After the replacement or adjustment of the VR, be sure to set the variable value of . the VR in the test mode’s Volume Setting.

Apply greasing to the Volume gear mesh portion every 3 months. For spray greasing, use Grease Mate (Part No. 090-0066).

SPRING DYN-1269

KX (Oo | cimmii? O VOLUME GEAR MESH PORTION

O O

SLIDING FACE OF CAM

Page 39
  • SHIFT LEVER

@ In order to prevent electric shock and short circuit, be sure to turn off the power before performing work on the interior parts of the product.

CAUTION! |] @ Be careful not to damage wiring. Damaged wiring can cause electric shock or short circuit. @ Do not touch places other than those specified. Touching places other than those specified can cause an electric shock or short circuit accident.

If the Shift Lever operation is not satisfactory, remove the Shift Lever in the following procedure and replace the microswitch.

9-1 REMOVING THE SHIFT LEVER

Turn Power off.

Take out the 4 SPECIAL BOLTS and pull the SHIFT LEVER UNIT upward by paying careful attention so as not to damage the wiring. Disconnect the 2 connectors to allow the unit to be removed. ©O 00

When reinstalling, follow the procedure oppisite as when removing. At this time, ensure that“"DOWN” display

TAMPERPROOF SCREW MS X12, black appears on the upper part as shown.

Page 40

9-2 SWITCH REPLACEMENT

Each microswitch is secured with 2 screws. Remove the 2 screws and replace the Microswitch.

LAFF LY OUREM Ves M3 X 16 v GREASING

ICROSWITCH

After replacing the Switch, check to see if the switch is inputted as per Shift Lever operation in the Test Mode.

Page 41
  • ACCEL & BRAKE(S)

@ In order to prevent an electric shock and short circuit, be sure to turn power off before performing work by touching the interior parts of the product. @ Be careful so as not to damage wirings. Damaged wiring can cause an electric

WARNING! shock or short circuit accident. @ Do not touch places other than those specified. Touching places not specified can cause an electric shock or short circuit accident.

If Accel and Brake operation is not satisfactory, adjustment of Volume installation position or Volume replacement is needed. Also, be sure to apply greasing to the gear mesh portion once every three months.

10 - 1 ADJUSTING AND REPLACING THE V.R.

When released: When stepped on: Under 30 H Over COH Under 30 H Over COH

Check Volume values in the Test Mode.

Since work is performed inside the energized cabinet, be very careful so as not to touch undesignated portions. Touching places not specified can cause an electric shock or short circuit.

® Take out the 2 truss screws and remove the Front Cover TRUSS SCREW '2) W4axé. chrom: from the Accel. & Brake unit. @ Loosen the screw which secures the Potentiobase, and adjust the Volume Value by moving the Base. @ Secure the Potentiobase. @ Perform Volume setting in the Volume Setting Mode.

FRONT COVER SCREW Wa 12, «flat washer

TOTENNOBASE VR. 220-8373, S484

Page 42

Check Volume values in the Test Mode.

Since work is performed inside the energized

cabinet, be very careful so as not to touch ; ; : ‘TRUSS SCREW (2

undesignated portions. Touching places not MAx8 POTENTIOCOVER

specified can cause an electric shock or short ]

¢ circuit.

Take out the 2 truss screws and remove the Front Cover

from the Accel. & Brake unit.

Loosen the screw which secures the Potentiobase, and

adjust the Volume Value by moving the Base. Secure the Potentiobase. ©© © © Perform Volume setting in the Volume Setting Mode.

10 - 2 GREASING

Gron Be sure to use designated grease. Using undesignated grease can

cause parts damage.

IMPORTANT!

Once every 3 months, apply greasing to the Spring and Gear Mesh portion. For spray greasing, use GREASE MATE (PART No. 090-0066).

Page 43

11 . COIN SELECTOR

HANDLING THE COIN JAM

If the coin is not rejected when the REJECT BUTTON is pressed, open the coin chute door and open the selector gate. After removing the jammed coin, put a normal coin in and check to see that the selector correctly functions.

CLEANING THE COIN SELECTOR

The coin selector should be cleaned once every 3 months. When cleaning, follow the procedure below: @) Turn the power for the machine OFF. Open the coin chute door. Open the gate and dust off by using a soft brush (made of wool, etc.).

(6) Remove and cleen smears by using a

soft cloth dipped in water or diluted chemical detergent and then squeezed dry. (@) Remove the CRADLE. When removing the retaining ring(Ering), be very careful so as not to bend the shaft. © Remove stain from the shaft and pillow

portions by wiping off with a soft cloth,

etc. ©) After wiping as per #5 above, further apply a dry cloth, etc. to cause the coin selector to dry completely.

@ Never apply machine oil, etc. to the coin selector @ After cleaning the Coin Selecting,

IMPORTANT! Insert a regular coin in the normal

working status and ensure that the Selector correctly functions. ©

FIG. Ila

Insert a coin

COIN INSERTION TEST aie

Once a month, when performing the COIN SW gutton pressed TEST, simultaneously check the following: down and check if it is + : : rejected. O Does the Coin Meter count satisfactorily? an O Does the coin drop into the Cashbox correctly? COIN METER O Is the coin rejected when inserted while keeping the REJECT BUTTON is pressed down? FIG. lle

Page 44

OPTIONAL DOLLAR BILL ACCEPTOR

@ THE COIN DOOR ASSEMBLY USED ON JAMBO SAFARI COMES EQUIPPED TO ACCEPT A DOLLAR BILL ACCEPTOR. ALL NEEDED WIRING CONNECTIONS ARE CONVIENENTLY LOCATED INSIDE THE GAME FOR THIS APPLICATION.

@ THE COIN DOOR CAN ACCCOMMODATE THE FOLLOWING VALIDATORS:

HOLE POSITION#1 Mars 2000 series (FORWARD-MOST POSITION)

HOLE POSITION#2 Mars 2000 series DBV45 (JCM)

HOLE POSITION #3 CURRENTLY NOT USED

HOLE POSITION #4 DSI01*

*The back flange on the chute can be removed for hold position #4. If the flange is not removed, it may interfere with the back of the cabinent.

The frame and cashbox enclosure on this coindoor has been modified to accomodate a Mars 2000 series upstacker. A 2000 series stacker can be added by simply removing the top two entry door and replacing it with a one entry door with a cut-out for a stacker. This one entry door can be ordered through Coin Controls or one of Coin Controls authorized distributors. The part number is 91-4000-01. The Mars stacker can be obtained through an autherized Mars distibutor.

4l

Page 45

I Croyk T [elels R!iN O/N|T/R/O|LIS Ti OiNn ALL alt 1850 HOWARD ST., ELK GROVE EL 60007 (847) 228-1810

+ MARS SERIES 2000 UPSTACKER ADAPTABLE G OVER/UNDER TWO ENTRY COIN DOOR*

PART #DESCRIPTIONCOSTPART #DESCRIPTIONCOSTPART #DESCRIPTIONCOST
1) I2-4060-KX S-10 ACCEPTOR19.5016) 91-1108-16 BEJRCT FLAP NYLON, BLACK = 2.7028) 23-L0UL-00 (2F OC ABTER8.50
I-4150-011 S-7 US 8.2512.00IT) S-HM13-OL ENTRI/REJECT BITTON 25¢4.4523-03-00 4.57 00 WBTER3.50
2) AHITTH0 PLASTIC CASBBOX7.4018) 91-1117-00 LAVPHOLDER1.4023) 90-1082-01 ABTER & LOCKOUT SCREPe)
3) 20-4189-00NCLOSTRE, 2200027.5019) 1-1121-00 B/R BUTTON SPRINGBi30) 22-1400-00 LOCKING BAR7.00
4) 90-1002-00 HINGE SCREBb20) S1-1118-006Y LAMP FRDGE BASE%SL) 90-1019-00 3/4" LOCKTASHER2
5) 90-1003-00 CLAMP SCRET%21) S-C3LL-16 BUTTON BREEL BLACK2.70
6) 90-1017-00 SCREV BRZEL NYLON42) M-1312-16 RRJECT BRZEL BLACK2.70
7) 90-1206-02 H-40 KEP AUPB23) 91-2125-00 127 LOCKOUT COTL ASSEMBLY12.85
8) 90-1300-00 KEYHOOK324) GL-2216-16 NICROSRITCH ASSEMBLY15.00
9) 91-0508-16 FRAME30.00UA) SI-L1L6-16 MICROSPITCE BLACK5.40
10) 91-0506-00 CLAKPAbSL-LLIG-HL MICROSRITCH THITE5.40
$1) 91-0547-00 DOUBLE D Call Lock5.2SI-LLL6-10 MICROSRITCH RED5.40
12) 91-0603-16 BLACK MINT DOOR5.402B) S1-1125-00 WICROSRITCH PLASTIC COVER = 85
13) 91-0604-(6 2 ENTRY UPPER DOOR10.0025) 92-1002-01COT INLET LAMP SIDE1.80
14) 91-4008-099 LOCKOUT BRACKET4.3026) $2-4002-021 COIN INLET COVER SIDE1.80
15) 91-1008-107 RASEPLATE ASSENBLY5.0021) 92-1002-10 HOLD DOTY BRACKET1.50

JAN. 1998 FORM 92-1003-05

Page 46
  • MONITOR
CAUTION! When performing such work as installing and removing the monitor, inserting and disconnecting the external connectors to and from monitor, be sure to disconnect the power connector (plug) before starting work. Proceeding the work without following this instruction can cause electric shock of malfunctioning. Using the monitor by converting it without obtaining a prior permission is not allowed. SEGA shall not be liable for any malfunctioning and accident caused by said conversion.

COIL DEMAGNETIZER| @ FOCUS LEAD

SECONDARY SIDE FBT. Approx. (Chassis, sheet metal work, CRT, etc.) Disconnect or unplug 29kV Primary side and secondary side The monitor’s circuit which is divided into the Primary side and secondary side, is electrically isolated. Do not touch the primary side and the secondary side simultaneously. Failing to observe the instruction can cause electric shock, and this is very dangerous. SECONDARY SIDE When making monitor adjustments, use a non- (Chassis, CRT) conductive driver and make adjustment without touching any other part other than the Adjustment V.R. and Knob. Also, be sure not to cause a shortcircuit to the Primary side and the Secondary side. If short-circuited, it can cause electric shock or malfunctioning, which is very dangerous.

High tension Voltage Some of the parts inside the monitor are subject to high-tension voltage in excess of 20,000 volts and very dangerous. Therefore, do not touch the monitor interior. Should soldering & paper wastes, etc. be mixed in the monitor, turn the power off so as not to cause malfunctioning or fire hazard.

2) ANODE CAP PRIMARY SIDE DEMAGNETIZER. REAR PART

c @® ANODE LEAD |_ MAIN BD Approx. 29 kV

(black) Approx. 10 kV

Connecting the CRT and PCB For combining the CRT and PCB, use the specified part No. to maintain the status of adjustments made at the factory. The anode of the CRT itself will be accumulitavely charged as time elapses, generating high tension voltage which is very dangerous. The monitor should be used with the Chassis, CRT and PCB assembled. When repair, etc. is required at the time of malfunctioning, be sure to send it in an “as assembled” condition. If these are disassembled, what’s charged to said high tension voltage can be discharged, causing a very hazardous situation. Therefore, under no circumstances should it be disassembled.

CAUTION! Static Electricity Touching the CRT surface sometimes causes you to slightly feel electricity. This is because the CRT surfaces are subject to static and will not adversly affect the human body. Installation and removal Ensure that the Magnetizer Coil, FBT (Fly-Back Transformer), Anode Lead and Focus Lead are not positioned close to the sheet metal work’s sharp edges, etc. and avoid damaging the insulated portions so as not to cause an electric shock and malfunctioning. (For the name of parts, refer to the above figures.)
Page 47

For the purpose of static prevention, special coating is applied to the CRT face of this product. To protect the coating, pay attention to the following points. Damaging the coating film can cause electric shock to the customers. For the caution to be heeded when clearing, refer to the Section of Periodic Aluminum Foil inspection Table. Do not apply or rub with a hard item (a rod with pointed edge, pen, etc.) to or on C.R.T. surfaces. Avoid applying stickers, seals, etc. on the C.R.T. face. Do not remove aluminum foils from the C.R.T. corners. Removing the aluminum foils can cause static prevention effects to be lowered.

CAUTION!

Monitor adjustments have been made at the time of shipment. Therefore do not make further adjustment without a justifiable reason.

CAUTION! Adjusting the monitor which contains high tension parts is dangerous

work. Also, an erroneous adjustment can cause deviated synchronization and image fault, resulting in malfunctioning. When making adjustment, utilize a resinous Alignment Rod. Servicing with bare hands or using conductive tools can cause electric shock.

Page 48

NANAO monitor: 200-—5242-—2 4—0 4 (24K mode)

feel (6) Cfianam Fig Bie °&

@ oO

SANWA monitor: 200-5 2 4 3—2 4 (24K mode)

COROROMCHORCEOMOCROM”

RGAIN GGAIN BGAIN — BRIGHT HSIZE HHOLD HPOS! VSIZE VHOLD VPOSI

R-GAIN

G-GAIN ........ Controls colors.

B-GAIN

BRIGHT........... Controls screen brightness.

H. SIZE ........... Controls horizontal screen size.

H. HOLD ....:.:.. Provides horizontal synchronization, i.e., controls right/left hold.

Controls horizontal display position on screen.

. Controls vertical screen size.

. Provides vertical synchronization, i.e., controls up-down hold.

. Controls vertical display position on screen. BOOELOOSHOSO CONTRAST... Adjusts image contrast.

Page 49
  • REPLACEMENT OF FLUORESCENT LAMP

@ When performing the work, be sure to turn power off. Working with power on can cause an electric shock or short circuit accident. @ The Fluorescent Lamp, when it gets hot, can cause burns. Be very careful when replacing the Fluorescent Lamp.

To perform work safely and securely, be sure to prepare a step which is in a secure and stable condition. Not using a step or using an unstable step can cause violent falling down accidents.

CAUTION!

13 -1 REPLACEMENT OF FLUORESCENT LAMP

@ Take out the 3 Tamperproof screws from the rear of the billboard.

@ Be sure to disconnect all connectors

conected to the Marquee assembly before removing the Billboard and/or performing work.

® Take out the two screws which secure the lower billboard plate mask and remove billboard

TRUSS SCREW (3)

8-32x16 Tmpr Prf TOP SASH flat washer used

~

BILLBOARD

FLUORESCENT LAMP 20W, white,

local purchase

Page 50

14, PERIODIC INSPECTION TABLE The items listed below require periodic check and maintenance to retain the performance of this machine and ensure safe operation.

@ Be sure to check once a year to see if Power Cords are damaged, the plug is Plug, etc. Using the product with dust as is accumulated can cause a fire or

securley inserted, dust is accumulated between the Socket Outlet and the Power

WARNING! electrical shock. Periodically once a year, request the place of contact herin stated or the Distrib- @ uter, etc. where the product was purchased from, as regards to the interior cleaning. Using the product with dust as is accumulated in the interior without cleaning can cause a fire or short circuit accident. Note that cleaning the interior parts can be performed on a pay-basis.

Iten terval Reference

CABINETCheck Adjusters’ contact with surface.Daily
HANDLE MECHACheck Lamp.Monthly

Check VOLUME VALUE. Monthly Check ADJUST GEAR engagement. Trimonthly Greasing of GEAR. Trimonth ly

AGCEL. & BRAKECheck VOLUME value.Monthly

Cheek ADJUST GEAR engagenent. Trimenthly Gear and Sprigg portion greasing. | Trimonthly

SHIFT LEVERCheck switches.Monthly
COIN CHUTE TOWERCheck COIN SW.Monthly

Coin insertion test. Monthiy Cleaning of COIN SELECTOR. Trimonthiv

MONTTOR Check adjustments. Monthly of when moving,

Cleaning of CRT surfaces. Weekly

SHAT Antistatic measures Bimonthly

Applying grease to Seat Rail Trimonthiy

CAME BDMEMORY TEST.Monthly7
Check settings.Monthly7
Cabinet surfacesCleaningAs occasion arises. | Next page

ANTERIOR Cleaning Annually See above,

POWER SUPPLY PLUG Inspection and cleaning

CLEANING CABINET SURFACES

If the cabinet is badly stained, use a cloth which is dipped in the chemical detergent liquid diluted with water and then squezzed dry. Do not use thinner, benzine, alcohol or chemical dustcloth as these can damage Cabinet surf:

SEAT (Greasing to Seat Rail Portion) ns

Move the Seat to the rearmost portion and apply spray greasing to the _-, portion shown at the right once every 3 months by using NOK KLUBER L60 or GREASE MATE SEGA PART No. 090-0066. After greasing, move seat a few times forward and backward so as to allow the grease to be applied all over uniformly. Be sure to wipe grease which attaches to the surfaces of the PROTECT RUBBER on the seat Rail, or any excess grease.

Page 51
  • TROUBLESHOOTING Should trouble occur, first check connector connections.

PROBLEMS CAUSE COUNTERMEASURES

With Main SW ON, no activation Power is not supplied.

Power supply/voltage is not correct.

AC main fuse causes the power to be cut off due to momentary overload. Plug in correctly

Make sure that power supply/voltage is correct. Check fuse. Remove the cause of overload and replace fuse

Operation is unsatisfactory Volume Setting Failure

Poor mesh of V.R. gear.

Spring failure due to secular change of Accelerator and Brake Mecha. Perform Volume setting Adjust or replace V.R.

Adjust Gear mesh..

Replace the Spring.

Irregular sound emitted from inside Rear Cabinet Greasing to gear mesh portion is not satisfactory, or extraneous matter mixed in. Apply greasing or eliminate extraneous matter.

The color of the image on PROJ. screen is incorrect. Connector connections are defective. Check the connection for the RGB and SYNC connectors of the PROJ. TERM. BD and VPM BUFFER BD.

The image on PROJ. screen has color deviation. Affected by the magnetic field of installation location. Make CONVERGENCE adjustment. (Refer to Section 12.)

No sound is emitted. Sound Volume adjustment is not appropriate.

Sound BD and speaker are Adjust sound volume. (see Section 7).

Perform sound test to find and replace

is not possible. malfunctioning. defective parts.(Refer to Section 7).

NETWORK check NOT AVAILABLE NOT AVAILABLE will not finish.

Communication play |} NOT AVAILABLE NOT AVAILABLE

No sound from Cockpit. In correct Cabinet Type Setting. Correct Cabinet Type Setting.

The Fluorescent lamp does not light up. The Fluorescent tube is burnt out. Replace the Fluorescent tube (Refer to Section 11).

Shift operation is not satisfactory in gameplay. Shift SW malfunctioning. Replace SW

Page 52
  • GAME BOARD
WARNING!
CAUTION! @ In order to prevent an electrical shock, be sure to turn power off before performing work by touching the interior parts of the product. @ Be careful so as not to damage wirings. Damaged wiring can cause an electric shock or short circuit accident.

Do not expose the Game BD, etc. without a good reason. In this product, setting changes are made during the test mode. The Game BD need not be operated. Use the Game BD, etc. as is with the same setting made at the time of shipment.

16-1 REMOVING THE GAME BOARD

To replace the IC Board or to change dip switch settings, take out the IC board using the following procedure;

® Turn main switch off. @ Unlock the base, and remove the 2 truss screws from the side of the base. @® Turn the knob to unlock. The seat can be inclined in the direction shown. When inclining the seat, be careful not to damage seat parts. Carefully rest the backrest portion of the seat on the ground. ® If neccessary, protect the seat from damage by using a cloth or blanket on the floor. © Take off the 3 screws to remove the case lid. The game board is inside the shield case. © Take off a total of 4 screws from both sides with the seat being in an inclined state and remove the base lid F. Removing base lid F allows the Elec Base to be seen.

TRUSS _HEAD SCREW (2) / ¥5X12, black INCLINE THIS CAREFULLY.

{TRUSS HEAD SCREW(4) M5X12, black

Page 53

16 - 2 REPLACEMENT OF FUSE

WARNING! @ In order to prevent an electric shock, be sure to turn power off before performing work by touching the interior parts of the product. @ Be careful so as not to damage wirings. Damaged wiring can cause an electric shock or short circiut accident @ After eliminating the cause of the blowing of fuse, replace the fuse. Depending on the cause of the fuse blowing, using the fuse as is blown can cause generation of heat resulting in fire.

Incline the Seat and remove the Base Lid to view the Base interior. The composition of the Base interior is as shown. below. There is a fuse on each of the Connect BD. and Motor Drive BD. When replacing the fuse, be sure to use the specified one.

LOCAL PURCHASE

Page 54

16 - 3 COMPOSITION OF GAME BOARD

Ensure that the DIP SW setting is performed as designated as designated. Failure to observe thisw may cause functioning not suitable for tyhe operation, or malfunctioning.

IMPORTANT!

ASSY CASE NAO USA (840-0002D-01) :USA

SCREW (4) 7 63X30

ROM CASE NAO CTA 840-0002C

NN 840-0001A-O1 ASSY CASE NAOMI MAIN BD USA

DIP SW SETTING

IN the product, set all of the DIP SWes to OFF.

GE

Page 55
  • DESIGN RELATED PARTS

ITEM NO.

ll coppisite side og

PART NO.

DYN-OO11 LOCAL PURCHASE 999-0885 999-0870 SPG-1201-E DYN-1214-C DYN-1214-D DYN-1214-E SPG-2002 999-0868 999-0869 999-0871 999-0871 999-0883 999-0878 999-0872 999-0875 999-0876 999-0877 999-0879 999-0880 999-0881 999-0882 999-0884 999-0866 999-0867 DESCRIPTION

DENOMI PLATE W/O ORIGINAL DENOMINATION SHEET | GAME DECAL SEAT ADJUSTMENT JBA. DECAL INSTR SH JBA METER PANEL DESIGN PL TACO MTR TWIN DESIGN PL OIL MTR TWIN DESIGN PL WATER MTR TWIN STEERING EMBLEM DECAL MONITOR COVER L JBA. DECAL MONITOR COVER R JBA DECAL MAIN BASE L JBA DECAL MAIN BASE R JBA DECAL CONTRL TOP JBA LEFT DECAL SEAT CENTER JBA MARQUEE PLEX JBA DECAL SEAT BACK UPPER JBA DECAL SEAT MIDDLE W/LOG JBA DECAL SEAT LEFT JBA DECAL SEAT RIGHT JBA DECAL INSTR SHIFTER JBA. DECAL INSTR START BUTTON JBA DECAL CONTROL TOP RIGHT JBA DECAL CONTROL TOP CENTER JBA DECAL MARQUEE CAP LEFT JBA DECAL MARQUEE CAP RIGHT JBA

Page 56
  • PARTS LIST

TOP ASSY JAMBO SAFARI STD

i]

i]

oO

ITEM NO. PART NO.

1 999-0887 2 DUTS5-0300 3 999-0888 4 200-5787 22 INY-0004, 23 DYN-0008 25 DYN-OOI1 29 LOCAL PURCHASE 201 LOCAL PURCHASE 202 068-852216 203 000-T00440-0B 204 LOCAL PURCHASE 205 LOCAL PURCHASE 206 000-T00416-0C 209 010-P00408-F DESCRIPTION

ASSY BILLBOARD ASSY COIN CHUTE TOWER ASSY COCKPIT CLR DSPLY 29 TYPE 31K 100V. BACK LID INY BACK LID B DENOMI PLATE W/O ORIGINAL MARQUEE RETAINING PLATE 1/4-20X1 1/4” TMPR PRF SCREW FLT WSHR M8 M SCR PH W/FS BLK M4X40 HEX BLT 8/32-20X1 SPR WSHR 8/32-20X1 M SCR TH CRM M4X16 S-TITE SCR PH W/F M4X8

Page 57

ASSY BILLBOARD STDJBA (999-0887)

ITEM NO. PART NO. DESCRIPTION

1 999-0872 MARQUEE PLEX JAMBO SAFARI 2 999-0873 LOWER MARQUEE PLEX JBA 3 999-0731 MARQUEE COVER L 4 999-0732 MARQUEE COVER R 101 LOCAL PURCHASE ASSY FL 20W EX W/CONN HIGH S

Page 58

ASSY COINCHUTE TOWER (DUTS5-0300)

Page 59

ASSY COINCHUTE TOWER (DUTS5-0300)

ITEM NO. PART NO.

1 SPG1-0350 2 SPG1-0301 3 DYN-0302Y 4 DP-1167 5 BOX-CASH 10 DYN-0305 i 105-5202 12 SPG-0302 13 SPG-0303 101 92-1003-05* 102 220-5412 103 999-0169 104 220-5574 105 220-5575 106 999-0167 DESCRIPTION

SW UNIT COIN CHUTE TOWER COIN METER BRKT TNG LKG CASH BOX TOWER BRKT HOLE COVER WIRE BOX WIRE BOX LID ASSY C.C. 2DR MAG CNTR W/CONN CASTER 2 1/2” CAM LOCK W/KEYS CAM LOCK MASTER W/O KEY LEG LEVELER

  • This coin door is produced by Coin Controls and can be ordered through your local distributor.
Page 60

SW UNIT (SPG5-0350)

SOUND VOLUME

DEGAUSS SW TEST SW) SERVICE SW

ITEM NO. PART NO. DESCRIPTION

1SPG5-0351SWITCH BRKT
101509-5028SW PB IM
102220-5179VOL CONT B-5K OHM
103601-0042KNOB 22MM
104220-5412MAG CNTR W/CONN

105 509-5453-91-V-B ROCKER SWJ8 V-B

Page 61

AC UNIT (DRT 1-0400)

TEM NO. PART NO.

SPG5-0401 600-5843-25 280-5134-6N34 509-5453-91-V-B DESCRIPTION

AC BRKT CA & PLUG ASSY 15A W/F-L=2.5M BUSHING STRAIN RELIEF 6N34. SW ROCKER J8 V-B

Page 62

ASSY SPEAKER (SPG-1100)

ITEM NO. PART NO. DESCRIPTION

1 INY-1701 SPEAKER BRKT 101 130-5159 GULL BOX SPEAKER 80HM 5W

Page 63

ASSY VIRTUAL BUTTON TWIN (DRT5-1290)

ITEM NO. PART NO.

DRT5-1291 171-6478B 212-5205-12 509-5560-Y DESCRIPTION

VR BUTTON BRKT PC BD LIGHTING SW CONN JST M 12P RTA PB SW WIL6V ILY

Page 64

ASSY BASE BOX (DRT1-1500)

> = 2 °

go he °

] : * ~J Fb.

SS Se eS ~ %

ITEM NO. PART NO. DESCRIPTION

1DRT1-1501MAIN BASE
2DYN-2003BASE LID F
3DYN-2004LOCK TNG
4DYN-2005XFLOOR MAT
5DYN-2006HINGE 480
6DRT-1510ASSY BASE LID R
7DYN-2007XLID EDGE L
8DYN-2009XLID EDGER

101 220-5575 CAM LOCK MASTER W/O KEY

Page 65

MAIN BASE (DRT1-1501)

ITEM NO.

WYN PART NO.

DYN-2002X-A 999-0871 999-0871 999-0167 999-0169 DESCRIPTION

MAIN BASE BLANK STICKER BASE L STICKER BASE R LEG ADJUSTER BOLT 1/2X13X3 CASTER 2 1/2"

Page 66

ASSY SEAT TWIN IP (DRT-1600)

M8 Bolt for fastening the plastic: 82kgf+cm

a

E; FS g

a

wo] ai3|8 3/s|8 3g zlels

Page 67

ASSY SEAT TWIN IP (DRTI-1600)

ITEM NO.

SIDHAWNE

ll PART NO.

STC-1650 DRT-1602-A DRT-1603-A. STC-2201 STC-1604 999-0874 STC-1606 STC-1607 STC-1608 STC-1609 STC-1610 STC-1611 STC-1612 STC-1613 INY-1302-B 601-9059 601-9060 130-5159 601-6563-188 601-6563-100 280-5297 000-P00410-W 030-000816-S 050-H00800 060-S00800 000-T00616-0B 010-P00408-F DESCRIPTION

ASSY WOOFER UPPER SEAT LOWER SEAT SEAT BASE SEAT FRAME SEAT REAR COVER IP. SEAT MOUNT TRAY SP MOUNT BRKT SPEAKER NET L SPEAKER NET R SAFETY GUARD CABLE BEAR BRKT PROTECT RUBBER SAFETY GUARD F MASK CUSHION SIDE SEAT RAIL L SEAT RAILR GULL BOX SPEAKER 80HM 5W BUSH 2.4T BUSH 2.4T SCRIVET 8 1K31 M SCR PH W/FS M4X10 HEX BLT W/S M8X16 HEX NUT M8 SPR WSHR M8 M SCR TH BLK M6X16 S-TITE SCR PH W/F M4x8

Page 68

ASSY WOOFER (STC-1650)

ITEM NO. PART NO. DESCRIPTION

1 STC-1651 WOOFER BRKT F 2 STC-1652 WOOFER BRKT R 101 130-5160 SUB WOOFER 4 OHM 30W.

Page 69

ASSY ACCEL&BRAKE (SPG-2200)

Page 70

ASSY ACCEL&BRAKE (SPG-2200)

ITEM NO. PART NO.

SPG-2201 SPG-2202 SPG-2203 SPG-2204 SPG-2205 SPG-2206 SPG-2207 SPG-2208 SPG-2209 SPG-2210 SPG-2211 SPG-2212 SPG-2213 SPG-2214 SPG-2215 SPG-2216 SPG-2217 SPG-2219 SPG-2220 SPG-2221 100-5263 220-5484 601-7944 310-5029-F15 280-0419 028-A00304-P. 020-000520-0Z 000-P00420 000-P00508-W 000-T00408-0C FAS-450005 000-P00405 FAS-000001 050-H00500 060-F00400 DESCRIPTION

BASE ACCEL PEDAL BRAKE PEDAL ACCEL SPRING BRAKE SPRING SHAFT ACCEL GEAR BRAKE GEAR NUETRAL STOPPER VR PLATE ACCEL VR PLATE BRAKE AMPL GEAR GEAR SHAFT STOPPER RUBBER CUSHION COVER VR COVER GEAR STAY WSHR NUETRAL STOPPER BEARING 12 VOL CONT B-5K OHM GEAR 15 SUMI TUBE F F 15MM HARNESS LUG SET SCR HEX SKT CUP P M3X4 HEX SKT H CAP SCR BLK M5X20 M SCR PH M4X20 M SCR PH W/FS M5X8 M SCR TH CRM M4X20 SPR PIN BLK OZ 6X10 M SCR PH M4X5 M SCR TH CRM M3X6 HEX NUT M5 FLT WSHR M4.

Page 71

ASSY HANDLE MECHA (CTA-2100)

Page 72

ASSY HANDLE MECHA (CTA-2100)

ITEM NO. PART NO.

CTA-2101 CTA-2101 CTA-2103 CTA-2104 CTA-2105 CTA-2106 CTA-2107 DYN-1262 DYN-1269 DYN-1273 BVG-1340 BVG-1341 SLC-1130 SLC-1141X SOR-2112 SOR-2113 SOR-2115 SPG-2109 601-6172 601-6959 601-8966 SLC-1108

100-5018 100-5112 100-5041 220-5484

028-A00408-P. 028-A00308-P. FAS-650011 000-P00408-W 000-P00412-W 060-F00600 050-U00600 060-F00800 050-U00800 065-E00700 060-S00800 DESCRIPTION

HANDLE BASE BASE LID HANDLE SHAFT STOPPER BOLT SPRING HOOK SPACER RING VR BRKT SWING ARM SHAFT EXT SPRING SWING ARM FLT WSHR 8.1-12X2 FLT WSHR 4.1-12X2 ADJUST RING WHITE CAM BEARING SHAFT SPACER KEY 5X10 STOPPER RUBBER GEAR 48 GEAR 64 GEAR HOLDER WIRE HOLDER

BEARING BALL 8 BEARING 17 BEARING NSK F688 ZZ VOL CONT B-5K OHM

SET SCR HEX SKT CUP P M4X8 SET SCR HEX SKT CUP P M3X8 STP RING BLK OZ S17 M SCR PH W/FS M4X8 M SCR PH W/FS M4X12 FLT WSHR M6 U NUT M6 FLT WSHR M8 UNUT M8 E RING 7MM SPR WSHR M8

Page 73

ASSY SHIELD CASE NAO (840-0013D-01)

ITEM NO. PART NO. DESCRIPTION

1 840-0013A-01 SHIELD CASE JBA NAO USA 2 840-0013C ROM CASE NAO

Page 74

ASSY ELEC BASE (CTA1-4500-02)

4 e le (8)

oS oS oP

e

=

NNN 2 [eum )

Ss

ITEM NO. PART NO. DESCRIPTION

1 NOT AVAILABLE WOODEN BASE ELEC

101560-5250-01XFMR 12.8V 8A

102 LOCAL PURCHASE FUSE BLOCK W/ FUSES

104838-11651-91LOW PASS AMP

105 837-13551-92 VOBD

106 840-0002D-01 NAOMI BD 107 400-5330-03 PWR SPPLY

108838-11650-29EQ POWER AMP
Page 75

ASSY COCKPIT 1P (DRT1-10001)

= oa Ss S a

Details of PART B

*07)(108)(106)(07)

Page 76

ASSY COCKPIT 1P (DRT1-10001)

ITEM NO. PART NO.

DRT5-20001 DRT5-1031 DRT5-1046 DRTS5-1201 SPG-1004 SRT-1002 INY-1016 SPG-1008 TTR-1067X SPG-1005 DYN-1025 INY-1015

200-5787

280-5112 280-5113 280-5114 280-5185-6 601-6231-C100 DESCRIPTION

ASSY MAIN BASE 1P MONITOR COVER L 1P MONITOR COVER R 1P ASSY CONTROL PANEL MONITOR STAND WIRE COVER BOX MONITOR SUPPORT ROOF LID MONITOR MASK MASK HOLDER RUBBER CUSHION CRT ADJUST PANEL

ASSY CLR DSPL 29 TYPE 31K 100V

BUSH FOR TV COLLAR FOR TV SPACER 6.4-25x2 SPACER TUBE L=6 EDGING NEW TYPE

Page 77

) ) Yen

Page 78

ASSY CONTROL PANEL (DRT1-1201)

ITEM NO.

YAURWNE .o

ll PART NO.

DYN-1201 DYN-1209X INY-1203 JBA-2001 SPG-1205 INY-1204 DYN-1223X SPG-1204 CTA-2100 610-0408-91 DRTS5-1290 SPG-2039

020-000820-0Z 060-F00800 060-S00800 050-H00800 FAS-200013 000-T00416-0B 000-P00412-W 008-T00516-0B 030-000820-S 000-T00412-0C DESCRIPTION

STEERING WHEEL HANDLE COLLAR STEERING EMBLEM CONTROL PANEL COVER CONTROL PANEL BRKT SHIFT COVER INY SHIFT COVER B SPL BLT M8 ASSY HANDLE MECHA ASSY SHIFTER ASSY VIRTUAL BUTTON SPACER RING

HEX SKT H CAP SCR BLK OZ M8X20 FLT WSHR M8 SPR WSHR M8 HEX NUT M8 HEX SKT H CAP SCR CRM M4X16 M SCR TH BLK M4X16 M SCR PH W/FS M4X12 TMP PRF SCR TH BLK M5X16 HEX BLT W/S M3X12 M SCR TH CRM M4X12

Page 79

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 80

ASSY MAIN BASE 1P (DRT5-20001)

ITEM NO. PART NO.

DRT-1500 DRT1-1600 SPG-2200 CTA1-4500 SRT1-0400 SPG-1502 RAL-2007 RAL-2008 SPG-1503 260-0011 DESCRIPTION

ASSY BASE BOX ASSY SEAT TWIN ASSY ACCEL&BRAKE ASSY ELEC BASE AC UNIT PEDAL BASE RUBBER HOLDER R TWIN RUBBER HOLDER L TWIN FAN BRKT AXIAL FLOW FAN AC100V 50-60 HZ

Page 81

VISIT OUR WEBSITE!

Netscape: SEU SERVICE HOMEPAGE

ve BA egymadat cs FZ 5 GoTo: J [http:/Avww.seuservice.com/SEGASERVICE/mainpage.htm|

MAILING LIST

SEGA DISTRIBUTORS

SERVICE STAFF

DARL'S OFFICE

HOME

[¥2K COMPLIANCE]

Sega Enterprises Inc.,USA Service Department Phone (650)-632-7580 Fax (650)-632-7594

Best Viewed with [What's new] [Manuals] [Bulletins] [Part Numbers][Game Monitors], [Board Systems] [Mailing List](SEGA Distributors] [Service Staff] [Darl's Office] [Samples],

Coin-Op Links:

Star Tech Journal

Amusement industry Mega Site

/f you have any questions about this Home Page please E-Mail to:

dari. davidson@seu.sega.com OR fan.rockhili@seu.sega.com

A total of BIR YC IE Mi) people have accessed this page.

Page 82

SEGA ENTERPRISES, INC. (USA)

45133 Industrial Drive Fremont, CA 94538 (415) 701-6580 phone (415) 701-6594 fax