CATHODE RAY TOMES

Asteroids Deluxe Cocktail DP-174-1st-02B

Asteroids Deluxe (rev 3) (Atari, 1980) · Drawing Package · 1 pages · original scan

Page 1
Scan of page 1

INPUTS

PLAYER INPUT CIRCUITRY

Gggss #iiimi,,

sor nent [i

<eeaee]

J denotes a test point

OPTIONS INPUT CIRCUITRY

VIDEO INVERTER

Do nv

‘The x: and y-video inverter circuits are identical; therefore, only the x-video inverter circuit Is explained. For invertered video operation, pin 19 is grounded which turns ‘on transistor Q13 and turns off transistor Q12. In this state INV is. +82 VOC and NONINV is 8.2 VOC.

For a noninverted video output, pin 19 is unconnected

and floats. In cocktail games, pins 19 and 7 are shorted ‘and have a potential of +5 VDC. This causes transistor {013 to be cut off and transistor 12 to be turned on. INV Is then -82 VOC and NONINV is approximately + 82 VOC.

In upright games, only the x-video inverter is used. In ‘cocktail games both x-and y-video inverters are used, and In cabaret games video inversion is not necessary, 80 neither is used.

‘Sheet 2, Side B DP-17402 st printing OUTPUTS

DIAG STEP (diagnostic step), 3. KHz, SELF-TEST SLAM, HALT, FIRE, and HYPER inputs are read by the MPU ‘when SINPO (switch input zero enable) is low. Switches to be ‘wad are selected by ABO thru ‘AB2 from the MPU. All inputs fare read on DB7. Switch inputs ‘are active when pulled to ‘ground. DIAG STEP, 3 KHz, and SELF-TEST are signals read by the MPU to initiate and control the game's selttest procedure. SLAM Is a signal read by the MPU to indicate the status of the antisiam switch mounted fon the coin door. The MPU reads HALT to determine the slate of the vector generator. The coin door and some con- ‘ol panel switches are read by the MPU when SINPT (switch input one enable) is low. Switches to be read are ‘selected by ABO thru AB2 from the MPU. All inputs are read on data line OB7. Switch inputs are “on” when pulled to ‘ground, IW determines the direc: tion of data flow (DB0-DB7) as addressed by ABO-AB3. When FIW is high, the MPU reads the Input data from DIP switch LB. When FUW is low, the MPU writes the audio 1/0 instruction for an output.

‘The 2 input from the MPU is. the operating frequency for the audio UO chip and sets the tim ing for data bus lines OB0-DB7.

When PKYDCD, ABI0, and ABI1 are high and ABE is low, a chip select pulse is gated 10 the audio 1/0 chip. This pulse prepares the audio 1/0 for ‘operation. The game option switches are read by the MPU when OPTS (option switch enable) is low. Switch toggles to be read are selected by ABO and ABI trom the MPU. Switch toggles 4, 3, § and 7 are read on data {ine DBO and toggles 2, 4,6 and 8 are read on DBI. Toggle inputs are “on” when pulled to ‘ground.

exoroor

Ges Te 00 exravoe vee —$ exravos

Boag ‘The Custom Audio chip M7/8 generates most of the sounds for Asteroids Deluxe™

oy exevosne—

me“) Tese fe} sv02

‘The EXPLODE sound is heard when any object explodes. Noise is Sampled at a frequency determined by P7, and control bits EXPITCHO and EXPITCH1. Changing the samp lng rate changes the pitch of the ex plosion. The noise is amplitude. Modulated in RB by EXPAUDO- EXPAUDS,

[RB and P@ generate random noise. This noise is filtered by P11 and produces the tumble sound heard when the ship is thrusting. LAMP, LED, AND COIN COUNTER OUTPUT

oer con {a} eoars com

oe aay eee com This circuit consists of coin counter drivers 08, (29, 210 and data latch M10, clocked by the micro- Computer's address decoder. When the input to drivers clocked high, its collector goes low, ground: ing the return of the coin counter in the coin door. When START! or START2 is clocked low, it grounds the START LEDs in the control panel

VIDEO OUTPUTS

sua

ge FPF

EWleenoies change by incicated revision <= penotes a test point eT At enon kc maw ‘The video-output cicuit consists of three individual circuits: Xaxis, Y-axis, and Zaxis. ‘The X-axis and Y-axis video-output circuits each consist of a digital-to-analog converter, (OAC), currentto-voltage converter, two sample and holds, and amplifier. The Zaxis, video-output circuit consists of a shift register and a summer.

X and ¥ Outputs ‘The DACs (011 and B11) each receive binary numbers from the vector generator’s position counter outputs. These numbers represent the location of the beam on the monitor. For the nom-inverted X axis, the numbers range from 0 to 1023, where Os at the far left of the monitor screen, $12 i atthe center, and 1023 sat the far right. For the non-inverted Y axis, the numbers range from 128 to 996, where 128 is at the bottom of the monitor ‘screen, 512's at the center, and 996 is atthe top. When the X axis and Y axis are inverted, the monitor picture is turned upside down. This is used for a two-player cocktail game. ‘The DACs convert these binary number inputs to current outputs. The DACs’ current outputs are applied to the pin inputs of current tovoltage converters C12 and A12. From the current-to-vltage converters, the signal is fed to two sample-and-hold circuits: One is non:inverted and the other is inverted. The non-inverted sample and hold consists lof one stage of analog switch O12 and capacitor C89 for the X axis, and B12 and C109 for the axis. The inverting sample and hold consists of invertor E12, one stage of analog switch 12, and capacitor C88 for the X axis and BICI2, BI2 and G10 for the ¥ axis. ‘The sample-and-hold circuits are controlled by SHCON (sample and hold contro}. 'SHCON is derived by gating 3 MHz from the microcomputer clock circuitry and VGCK" from the vector generators state generator. The result of these inputs insures that the ‘norinverted and inverted analog signals that are applied to the analog switches have sutficiently stabilized before being applied to the sample-and-hold capacitors.

‘The output swing of SHCON is ~8 to +8 VDC. When SHCON is high, the voltage charges or discharges the sampleand-hold capacitors to the X and Y analog voltage Value. The voltages are then applied to the Inputs of the second analog switch. These ‘switches select either the non-inverted or inverted X-axis and Y-axis outputs. The outputs are then amplified by the second stages of C12 and A12 for an impedance-matched output to the Xand Y inputs to the monitor. Since the monitor doesn’t have feld-adjustable Xand ¥ gains, the gains are adjustable by variable resistors R120 and R126. Z Output ‘The Z-axis video output receives six inputs. BVLD (beam valid), from the output of the ‘counters, tells the Z axis to draw the line. BLANK (vector line ‘ ‘machine, tells the Z axis to stop drawing a line. ‘SCALED thru SCALES (grey-level shading scale), Irom the output of the vector generator’s ata ltch tls the 2 axis the greyevel shading of te line hat is being drawn onthe monitor.

When BVLD and BLANK are both high, a high is clocked through shift register K9 that turns transistor Q3 off. This allows the scale inputs to be passed through transistor Q2. When ‘goes low, a low is clocked through K8, transistor Q3 tums on, and the signal is grounded at the base of transistor 2. ‘The scale inputs at the base of transistor Q1 determine Q1's emitter voltage, during the line draw period. The SCALEO thru SCALES resistors R36 thru R39, resistor P35, and resistor Ré0 result in a range of about + 1.0 VDC when all are low and + 4.0 VDC when all are high. The emitter of Qt follows at about + 1.7 o 4.7 VDC, while the emitter of tran: sistor Q2 follows at about + 1.0 to 40 VOC. This output Is applied to the Z input of the monitor. Since there are brightness and conirast controls in the monitor, there are no adjustments in this circuit.

@ ATARI

Sheet 2, Side B

ASTEROIDS DELUXE™ Switch Inputs, Coin Counter, LED and Audio Outputs

© 1801 Ata, he