CATHODE RAY TOMES

Bally Midways Licensed Games Standarized General Instructions (M051-00132-0000)

Licensed Games (Bally/Midway, 1983) · Manual · 55 pages · 37 sections · original scan

Page 1

Bally/Midwavy’s Licensed Games |

Standardized General

Instructions

Ciallly MIDWAY MFG.CO.

10750 W. Grand Avenue Franklin Park, Wlinois 60131 U.S.A.

Phone: (312) 451-1360 Cable Address: MIDCO Telex No:: 72-1596

FORM NO. M051-00132-0000

Page 2
WARNING THIS GAME MUST BE GROUNDED. FAILURE TO DO SO MAY RESULT IN DESTRUCTION TO ELECTRONIC COMPONENTS.
WARNING: This equipment generates. uses. and can radiate radio frequency energy and if not and used in accordance with the instructions manual. may cause interference to radio communications. It has been tested and found to comply with the limits for a CLASS A computing device pursuant to SUBPART J of PART 15 of FCC RULES. which are designed to provide reasonable protection against such interference when operated (na commerical environment..Operation of this equipment ina residential area Is likely to cause interference in which case the user at his own expense will be required to take whatever measures may be required to correct the interference.

ELECTRICAL BULLETIN: FOR ALL APPARATUS COVERED BY THE CANADIAN STANDARDS ASSOCIATION (CSA) STANDARD C22.2 NO. 1, WHICH EMPLOYS A SUPPLY CORD TERMINATED WITH A POLARIZED 2-PRONG ATTACHMENT PLUG.

CAUTION: TO PREVENT ELECTRIC SHOCK DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET

PRES SORE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE

ATTENTION: POUR PREVENIR CHOCS ELECTRIQUES NE PAS UTILISER CETTE FICHE POLARISEE AVEC UN PROLONGATEUR. UNE PRISE DE COURANT OU UNE AUTRE SORTIE DE COURANT, SAUF SI LES LAMES PEUVENT ETRE INSEREES A FOND SANS EN LAISSER AUCUNE PARTIE A DECOUVERT.

CBally| MIDWAY Snveites Your Ta Use

OUR TOLL FREE NUMBERS FOR SERVICE INFORMATION CONCERNING THIS GAME, OR ANY OTHER BALLY/MIDWAY™ GAME YOU NOW HAVE ON LOCATION.

CALL US FOR PROMPT, COURTEOUS ANSWERS TO YOUR PROBLEMS

ANSWERS TO YOUR PROBLEMS.

Continental U.S. 800-323-7182 Illinois Only 1-800-942-0497

© COPYRIGHT MCMLXXxXIIl BY BALLY/MIDWAY CO. ALL RIGHTS RESERVED. NO PART OF THIS PUBLICATION MAY BE REPRODUCED BY ANY MECHANICAL, PHOTOGRAPHIC, OR ELECTRONIC PROCESS, OR iN THE FORM OF A PHONOGRAPHIC RECORDING, NOR MAY IT BE TRANSMITTED, OR OTHERWISE COPIED FOR PUBLIC OR PRIVATE USE, WITHOUT PERMISSION FROM THE PUBLISHER. THIS MANUAL IS FOR SERVICE USE ONLY, AND NOT FOR GENERAL DISTRIBUTION. FOR PERMISSION REQUESTS, WRITE: MIDWAY MFG. CO., 10750 W. GRAND AVE., FRANKLIN PARK, iL 60131 Printed in U.S.A.

Page 3

I. Location and Setup

INSPECTION 1. 2.

5. Remove the game from its shipping crate. Inspect the entire outside of it for any signs of damage. 0 Any scratches?, dents?, cracks? O Any broken controls? O Any broken glass or plastic? O Just look it over closely and make a note of any signs of damage. . Remove the shipping cleats from the bottom of the cabinet. O UPRIGHT MODELS ONLY: In order to help prevent easy theft of your game, you may wish to remove the Caster Wheel Assemblies from the bottom of your cabinet at this time. . Install the four levelers, one at each corner of the cabinet. O Level the cabinet. Open the cabinet and inspect the inside of the game for any signs of damage. See Figure 1-1. O Also check to make sure all plug-in connectors on the wire harness are firmly seated.

NOTE: ALL connectors or plugs are keyed so they will only go together when all pins are properly lined up.

1-1 O Replug any connectors found unplugged. DO NOT FORCE PLUGS ONTO CONNECTORS. DO NOT FORCE PLUGS TOGETHER. If it won't go on easily, assuming the keys are lined up, it either does not belong there or is damaged. Make sure all printed circuit boards (P.C.B.’s) are firmly seated in their connectors. See Figure 1-1; These connectors are also keyed. The P.C.B.’s will only go into them one way without being damaged.

Note the location of the game's serial number. See Figure 1-1. Check all major subassemblies to be sure they are mounted securely. These are called out in Figures 1-1 & 1-2. Power supply. Control panel(s). T.V. monitor. Other P.C.B.’s and/or P.C.B. rack, etc. Power supply filter assembly. Transformer board assembly.
  • Make a note of any problems that can’t be easily corrected.
  • Call your distributor and/or service man about your problem list.
Page 4

ON/OFF SWITCH

INTERLOCK SWITCH

POWER SUPPLY CHASSIS

UPRIGHT

SERIAL NUMBER (MAY BE LOCATED ON ANY CORNER)

POWER SUPPLY CHASSIS

CONTROL PANEL (PLAYER 1)

GAME BOARD

INTERLOCK SWITCH _ (INSIDE DOOR) ~~ SERIAL NUMBER

TV. MONITOR @

INTERLOCK SWITCH

GAME BOARD

ON/OFF SWITCH

POWER SUPPLY CHASSIS (NOT SEEN)

TY. MONITOR

POWER SUPPLY P.C.B.

CONTROL PANEL (PLAYER 2)

ON/OFF SWITCH UNDER GAME ON | 4 PLAYER 2 SIDE

COCKTAIL

Figure 1-1 Location of Serial No., Interlock Switch, On/Off Switch, and Major Sub-Assemblies

Page 5

CONTROL PANEL

UPRIGHT

Figure 1-2 Major Sub-Assemblles (cont. from Fig. 1-1)

INSTALLATION

  • Location requirements:

O Power: Domestic 110 V @ 60 Hz Foreign 200 V to 240 V @ 50 Hz

Temperature: 32° to 100°F (0° to 38°C)

O Humidity: Not over 95% relative

O Space required: Upright 32" x 25” (81cm x 63cm) APPROX. Mini 20" x 24" (50cm x 60cm) Cocktail 32” x 22” (81cm x 55cm)

O Game height: Upright 70" (175cm) APPROX. Mini 61" (153cm) 7 Cocktail 29" ( 73cm) Figure 1-3 Interlock Switch Operation

Page 6
  • Voltage Selection: Your game is designed to work properly on the line voltage where you are located.:Check your line voltage with a meter to determine what its value is. Then ‘check the power input wires to the main power supply transformer on your game to be sure they are connected to taps which correspond to your line voltage value. If the power input wires to the main power supply transformer are not connected to taps which correspond to your local line voltage, move them to the proper taps. if the line voltage in your area falls outside the upper or lower limits of the range of inputs covered by the main power supply transformer, DO NOT PLUG YOUR GAME IN until you have talked with your distributor and/or service man and obtaineda solution to this problem. Otherwise you could damage your game.
  • Interlock and power ON/OFF switches. See Figure 1-1.

0 To help prevent the possibility of getting an electric shock while working inside the game cabinet, interlock switches have been installed at each cabinet access door (this DOES NOT include the coin door in the Upright and Mini models).

O When any access door is opened, the interlock switch installed there turns off all power to the game.

O Check each operation. After checking the line voltage in your area and determining that the input wires to the main power supply transformer: of your game are connected properly — or — after obtaining a solution to your over or under voltage problem from your distributor and/or your service man, plug the game into your A.C. wall outlet. The game ON/OFF switches for all models are located as shown in Figure 1-1. Turn the game on and allow it to warmup a few minutes. Slowly open each access door to the game (this does not include the coin door on the Upright and Mini models). As the door is opened approximately 1” (2.54cm) the power to the game should go off (the T.V. monitor, all the lights, and all sounds will stop). lf this does net happen, check the interlock switch by this door to see if it has broken loose from its mounting or if it is stuck in the “ON” Position. interlock switch for proper

1-4 If the switch is found to be bad, turn the game off, unplug it, and replace the interlock switch. When done, plug the game back into the wall outlet, close the access door, and turn the game back on. After the game has warmed up, repeat the above interlock switch test. When the interlock switch is working properly and turns the power to the game off, power may be restored to the game with the access door(s) open. Take hold of the interlock switch plunger and gently pull it out to its fully extended position. THIS IS TO BE USED ONLY FOR SERVICING THE GAME. See Figure 1-3.

GAME VOLUME ADJUSTMENT CONTROL. See Figure 1-4. The volume control pot is located on a P.C. board inside the game cabinet. See Figure 1-4. It may be reached through the coin door on the UPRIGHT models and through the rear access door onthe MINI models. On the COCKTAIL TABLE models, you will have to open the table top to reach it. To make the sounds louder, turn the pot clockwise as you face it (~~). To make the sounds less loud, turn the pot counterclockwise as you face it (4—~ ).

OPTION SWITCH SETTINGS To change the option switch settings, you DO NOT have to take the CPU board out of the game. They can be easily reached through the rear access door on the Upright and Mini models. On the Cocktail Table model, you do have to open the table top to reach them. When changing any options, ALWAYS check the results by playing the game to be sure the switches have worked properly and that no switches were accidentally moved that were not meant to be. (These switches are small and this can happen.) The option switch settings and what they will make the game do are shown in Figure 1-6. See Figure 1-5. for option switch locations.

Page 7

INCREASE

VOLUME CONTROL

Figure 1-4 Location of Game Volume Adjustment Control

DIP SW.1 POSITION 8D

DIP SW.2 POSITION 7D

Figure 1-5 Location of Option Switches

1-5

Page 8

BUMP & JUMP

OPTION SWITCH SETTINGS

LATTA STATA TR SWATCH 8D (SHI) TTT

COINS PER CREDIT COIN SWITCHES HUMBER T AND NUMBER 2)” SWHT SWi2 OWES SWH4 SWHS SWH6 SWHT SWAB

*1 = - COIN1 - CREDITOFF OFF ©—~
1 - COIN2 - CREDITSON OFF
1 - COIN3 - CREDITSOFF ON
2 - COINS4 = CREDITON ON

TEST CREDIT BUTTON Swi S¥#2 SWH3 SWH4 SW#S SWite SWH7 SWH8

* 1 - COIN1 - CREDITOFF OFF
1 - COIN2 - CREDITSON OFF
1 - COIN3 - CREDITSOFF ON
2 - COINS1 - CREDITON ON|

DIAGNOSTICS SWHT SWi2 SWH3 SWIG SWHS SWH SWHT SWE

  • CAME MODE OFF ~ OFF NORMAL TEST PROCEDURE ON OFF NO EFFECT OFF ON VIDEO P.C. BOARD TEST ONLY ON ON

CABINET DESIGN Swi SWH2 SWH3 SWIG SWHS SWhe SWH7 SWAB UPRIGHT CONTROL PANEL ON COCKTAIL CONTROL PANELS OFF UPRIGHT SCREEN ON COCKTAIL SCREEN OFF

FILTH TTA TATA ALLL DIP SWETCH 7D (SW) PILI TATU

NUMBER OF CARS PER GAME SWAT SWH2 SWHS SWHG SWHS SWH6 SWH7 SWHO

  • 3 CARS OFF OFF OFF OFF 5 CARS ON

BONUS CARS AWARDED EVERY SWHT SWH2 SWH3 SWH4 SWHS SWHe SWH7 SWHB

  • 1 CAR EVERY 30,000 POINTS OFF ” OFF “OFF OFF OFF 1 CAR EVERY 70,000 POINTS ON OFF 1 CAR ONLY AT 20,000 POINTS OFF ON 1 CAR ONLY AT 30,000 POINTS ON ON

RACK BONUS

] SWAT SWie SWS SWH4 SWHSSWH6 SWH7SWS
  • NORMAL GAME OFF OFF OFF OFF CAN CONTINUE GAME FOR ADDITIONAL COINS. ON

DIFFICULTY LEVEL OF PLAY SWF SWH2 SWi3 SWHS SWHS SWH6 SWH7 SWHS

  • EASY - COMPETITORS NOT TOO AGGRESSIVE OFF OFF OFF HARD - COMPETITORS VERY AGGRESSIVE ON

(= INCICATES FACTORY RECOMMENDED SETTINGS. PART NO. M051-00349-A014

Figure 1-6 Option Switch Settings

1-6

Page 9

II. Maintenance and Repair

Your NEW game needs certain types of maintenance to keep it in good working order. CLEAN, well MAINTAINED games attract players and EARN MORE PROFITS.

The most important thing for you to remember is to play your game thoroughly EVERY TIME you collect money from the coin box. JUST LOOKING at your game WILL NOT tell you if all its controls and inside parts are working Correctly. ONLY being familiar with and playing your game will inform you whether or not it is working the way it should. The second most important thing you should remember is to clean the outside of the game and coin acceptor mechanisms on a regular basis.

CLEANING The outside of the game cabinet plus the metal can be cleaned with any non-abrasive household cleaner. However, the front of the T.V. monitor tube and both sides of all other glass and plastic on or in the game MUST be cleaned with anti-static cleaner ONLY. For cleaning the coin acceptors: hot soapy water may be used on the plastic ones and any household cleanser may be used on the metal ones. If you wish, special coin machine cleaners that leave no residue may be Purchased from your distributor. DO NOT dry-wipe any of the plastic panels. This is because any dust that was on them can scratch their surfaces. If this has happened, anyone looking through this type of damaged plastic would feel he was looking at the game through a fog. This fogging damage CANNOT be repaired or reversed. The ONLY solution is to replace the damaged piece of plastic.

FUSE REPLACEMENT This game contains several fuses located as shown in Figure 2-1.

  • UPRIGHT MODEL: As viewed from the back, facing the cabinet, with the rear access door removed; the fuses are located on the Power Chassis and the Power Supply Board Assemblies.
  • MINI MODEL: As viewed from the back, facing the cabinet, with the rear access door removed; the fuses are located on the Power Chassis and the Power Supply Board Assemblies.
  • COCKTAIL TABLE MODEL: As viewed from the coin door side of the cabinet, with the monitor tilted open to one side; the fuses are located on the Power Chassis and Power Supply Board Assemblies. Replace fuses ONLY with the type and size listed in the Illustrated Parts Breakdown Section of your game manual. See the T.V. Monitor Manual (available on request from your Distributor or the Monitor manufacturer) and/or the T.V. Troubleshooting Section of your game manual for information on these fuses.

FUSES ON POWER CHASSIS & POWER SUPPLY PCB (TYP. ALL 3 MODELS)

Figure 2-1 Location of Fuses

Page 10

OPENING THE CONTROL PANEL. See Figure 2-2.

  • UPRIGHT MODEL: 2. MINI MODEL: O The control panel is held in place by two or three latches. See Figure 2-2. They are spring loaded to provide constant positive pressure on their latch plates. They can be reached through the coin door AFTER turning power to the game off. To release the latches, lift up and toward the front center of the control panel. Once they are released, unhook them from their latch plates. O To remove the control panel: Raise it up and tilt it toward you until you can see the cable behind it. Cradling the control panel between yourself and the cabinet, disconnect it from its cabling and nylon retaining strap. The control panel is now free and can be removed. O To reinstall the control panel, reverse this procedure.

CERTAIN

UPRIGHT MODELS ONLY O The control panel is held in place by two latches. See Figure 2-2. They are spring loaded to provide constant positive pressure on their latch plates. They can be reached through the coin door AFTER turning power to the game off. To release the latches, lift up and toward the center of the control panel. Once they are released, unhook them from their latch plates. To remove the control panel: Raise it up and tilt it toward you until you cansee the cable behind it. Cradling the control panel between yourself and the cabinet, disconnect it from its cabling and nylon retaining strap. The control panel is now free and can be removed. O To reinstall the control panel, reverse this Procedure.

Figure 2-2 Opening the Control Panel — Upright & Mini

Page 11

CLAMPS

Figure 2-3 Opening the Cocktail Game

  • COCKTAIL TABLE MODEL: O Each control panel is held in place by several screws, two on the inside of the cabinet and LFT three along the outside bottom edge of the CONTROL UP. control panel. Turn power to the game off. Open the coin box door and release the two REMOVE ne c Ox dc ¢ (2) SCREWS latches indicated in Figure 2-3. EACH SIDE
CAUTION: The right id latch is very close to on the

Once they're released, unhook them from their latch plates. Grasp the table top at “A” and open it as indicated in Figure 2-3.

REMOVE(3) SCREWS

CAUTION: Due to the weight of the monitor, EXTREME CARE MUST be taken when opening the cabinet.

Remove the screws which secure the control panel in place. See Figure 2-4. To remove the control panel(s): Disconnect it from its cabling. The contro! panel is now free and can be removed. O To reinstall the control panel, reverse this procedure. Figure 2-4 Removing the Control Panel — Cocktail

2-3

Page 12

REMOVAL OF THE MAIN-DISPLAY- GLASS AND/OR THE TV. BEZEL ASSEMBLY

  • UPRIGHT MODEL: See Figure 2-5.
NOTE: In order to do this, the control panel MUST be removed first. See the “Mini Model” procedure. O Turn the power to the game off and remove the control panel. O Certain models only: Remove the screws which secure the glass clamping plate and lift it out. O This frees the main-display-glass so it can be lifted up. O By putting your finger in the hole in the middle of the main-display-glass support, you can lift it up and out. Loosen the screws which secure the T.V. bezelglass-clamps in place. Move the clamps to the side and the bezel glass may be removed. Remove the above mentioned screws and the bezel with four bezel-glass-clamps may be removed. To reinstall the T.V. bezel assembly and the main-display-glass, reverse this procedure. o

DISPLAY

GLASS CLAMPS

. Figure 2-5 Removing the Main Display Glass & T.V. Bezel — Upright

  • MINI MODEL: See Figure 2-6.
NOTE: In order to do this, the control panel MUST be removed first. See the “Mini Model” procedure.

O Turn the power off to the game and remove the control panel. 01 Remove the screws which secure the glass clamping plate. O Lift out the glass clamping plate. This frees the main-display-glass so it can be lifted up. O By putting your finger in the hole in the middle of the main-display-glass support, you can lift it up and out. O Remove the screws which secure the T.V. bezel assembly and lift it out.

NOTE: Use the hole in the center of the maindisplay-glass support to grasp it.

0 Reverse this procedure to reinstall the T.V. bezel assembly and the main-display-glass.

DISPLAY GLASS

GLASS CLAMPING PLATE

Figure 2-6 Removing the Main Display Glass & T.V. Bezel — Mini

Page 13
  • COCKTAIL TABLE MODEL: See Figure 2-7.
NOTE: This may be done with the table top in the open or the closed position. If you decide to open the table top, TURN THE POWER TO THE GAME OFF FIRST.

O Remove tne screws which secure the table top glass clamps in place. O Remove the table top glass. D Loosen the screws which secure the T.V. bezelglass-clamps in place. Move the clamps to the side and the bezel glass may be removed. Remove the screws which secure the bezel assembly to the table top and the bezel with four bezel-glass-clamps may be removed. O To reinstall the T.V. bezel assembly and the table top glass, simply reverse this procedure.

Figure 2-7 Removing the Top Glass & T.V. Bezel — Cocktail

2-5 T.V. MONITOR REPLACEMENT

CAUTION: High voltages may exist in any television’ unit, even with the power disconnected. Use EXTREME CAUTION and do not touch electrical parts or the T.V. yoke area with your hands or with metal objects held in your hands! In addition, BE SURE TO USE HEAVY GLOVES when handling the monitor. You could cut your’ hands on the metal T.V. chassis without such protection.
DANGER: The TV. monitor DOES NOT contain an isolation transformer on its chassis (it is mounted instead on the floor of the cabinet). When servicing the monitor ona test bench, YOU MUST ISOLATE THE MONITOR FROM AC VOLTAGE WITH AN ISOLATION TRANSFORMER.
  • UPRIGHT MODEL: See Figure 2-8. D Turn power off to the game. O Open the rear access door. O Completely disconnect the T.V. monitor from all its cabling. DON’T FORGET THE CHASSIS GROUND WIRE. Before removing the T.V. monitor, the maindisplay-glass and bezel MUST be removed. See above “Upright Model” procedure. With the removal of only four bolts, the T.V. monitor and its mounting channels will be loose. The monitor mounting channels slide on top of and against two metal guides mounted to the cabinet’s right and left sides. The monitor is removed by sliding it out the back of the cabinet. See Figure 2-8. To reinstall the T.V. monitor, reverse this procedure. After replacing the T.V. monitor, be sure to run the game Self-Test.
  • MINI MODEL: See Figure 2-9. O Turn the power off to the game. O Open the rear access door. O Completely disconnect the T.V. monitor from all its cabling. DONT FORGET THE CHASSIS GROUND WIRE. Before removing the T.V. monitor, the maindisplay-glass and bezel MUST be removed. See above “Mini Model” procedure. With the removal of only four bolts, the T.V. monitor will be loose. a

Oo

CAUTION: BE SURE to support the T.V. monitor from the rear while removing the four bolts so it will Not fall out of the cabinet.
Page 14

ht hand latch is very close to ‘AGE on the monitor. The monitor is removed~by supporting it and CAUTION: The pulling straight back as shown in Figure 2-9. | the HIGH V! O To reinstall the T.V. monitor, reverse this O Once the latches are released, unhook them procedure. e After replacing the T.V. monitor, be sure to run from their latch plates. the game Self-Test. O Grasp the table top at “A” and open it as indicated in Figure 2-10.

  • COCKTAIL TABLE MODEL: See Figure 2-11.
CAUTION: due to the weight of the monitor, O Tur the power off to the game. EXTREME CARE MUST be taken when open- O Open the coin box door and release the two ing the cabinet. latches indicated in Figure 2-10.

REMOVE (4) BOLTS REMOVE

  • BOLTS

Figure 2-8 Removing the Monitor — Upright Figure 2-9 Removing the Monitor — Mini

2-6

Page 15

Figure 2-10 Opening the Cocktail Game

O Remove the screws which hold the table top glass clamps in place. 0 Remove the table top glass. O Lift out the T.V. bezel assembly. O Completely disconnect the T.V. monitor from all its cabling. DON’T FORGET THE CHASSIS GROUND WIRE. Remove the screws holding the T.V. monitor chassis to the “L” by the door hinge(s). See Figure 2-11. C Close the Cocktail Table and re-latch it. Remove the screws which secure the T.V. monitor mounting brackets to the edges of the slot cut in the table top. See Figure 2-11. O Pry up the end of each monitor mounting bracket with a screwdriver or similar tool until you can grasp them both. 0 Lift the T.V. monitor straight up and out of the table top being VERY CAREFUL not to bump the neck of the picture tube. O To reinstall the T.V. monitor assembly, reverse this procedure. O Be sure to check the clearance of the “L” brackets BEFORE setting the monitor into the table top. O After replacing the T.V. monitor, be sure to run the game Self-Test. REMOVE 6 SCREWS (3 EACH SIDE) LIFT MONITOR STRAIGHT UP

REMOVE 4 SCREWS (2 EACH SIDE)

Figure 2-11 Removing the Monitor — Cocktail

Page 16

PRINTED CIRCUIT BOARD (P.C.B.) REPLACEMENT

  • UPRIGHT MODEL: See Figure 2-12. CO Turn the power to the game off.

O Unlock and open the rear access door (game board) and the coin door (sound board). O Disconnect the game board from all its cabling. Disconnect the sound board from allits cabling. € Remove the indicated P.C.B. supports and lift the above P.C.B.’s out the cabinet.

REMOVE SUPPORT TO SLIDE GAME BOARD OUT REMOVE SUPPORT TO SLIDE POWER SUPPLY BOARD OUT

Figure 2-12 Removing P.C.B.’s — Upright

2-8 O Disconnect the power supply board from all its cabling, remove the P.C.B. supports indicatedin Figure 2-12, and slide it out the back of the cabinet.

0 To reinstall the above P.C.B.’s, reverse this procedure.

NOTE: P.C.B.’s are all keyed and will ONLY fit into their connectors one way without forcing them. The plugs on the cable harness which connectit to the P.C.B.’s are also keyed and will ONLY go onto their connectors one way without forcing them.

REMOVE SUPPORT TO SLIDE GAME BOARD FROM CABINET REMOVE SUPPORT TO SLIDE POWER SUPPLY BOARD FROM CABINET

Figure 2-13 Removing P.C.B.’s — Mini

Page 17

REMOVE SUPPORT TO SLIDE GAME BOARD OUT REMOVE SUPPORT TO SLIDE POWER SUPPLY BOARD FROM CABINET

Figure 2-14 Removing P.C.B.’s — Cocktail

  • MINI MODEL: See Figure 2-13. 0 Turn the power off to the game. O Unlock and open the rear access door. 0 Disconnect the game board from all its cabling. Disconnect the sound board from all its cabling. DO Remove the indicated P.C.B. supports and lift the above P.C.B.’s out of the cabinet. O Disconnect the power supply board from its cabling, remove the P.C.B. supports indicated in Figure 2-13, and slide it out the back of the cabinet. O To reinstall the above P.C.B.’s, reverse this procedure.
  • COCKTAIL TABLE MODEL: See Figure 2-14. O Turn the power off to the game. O Open the cabinet: Open the coin box door and release the two latches indicated in Figure 2-10.
CAUTION: The right hand latch is very close to the HIGH VOLTAGE on the monitor. Once they're released, unhook them from their latch plaies. :

O Grasp the table top at “A” and open it as indicated in Figure 2-10.

CAUTION: Due to the weight of the monitor, EXTREME CARE MUST be taken when opening the cabinet.

D To remove the power supply board. See Figure 2-14. Disconnect it from all its cabling. Remove the two smallest P.C.B. supports. Once these are removed, the power supply can be lifted out the top of the cabinet. To reinstall the power supply board, reverse this procedure. D To remove the game and Sound boards. See Figure 2-14. Disconnect the game board from all its cabling. Disconnect the sound board from all its cabling. Remove the indicated P.C.B. supports and lift the above P.C.B.'s out of the cabinet. To reinstall the game and sound boards, reverse this procedure.

Page 18

OPENING THE ATTRACTION PANEL:

  • UPRIGHT MODEL: See Figure 2-15. 2. MINI MODEL: See Figure 2-17. O Turn the power to the game off. O Turn the power off to the game. O Opening the attraction panel: O Remove the screws from the top and bottom of Remove the screws which secure the top the formed attraction panel. bracket in place. (They are on its top side.) See O Remove the formed attraction panel by pulling it Figure 2-15. straight away from the cabinet. This exposes the Remove the top bracket and slide up the attrac- attraction panel light bulbs and their mounting tion panel. This exposes the attraction panel board. fluorescent light tube and its mounting bracket assembly. To reinstall the attraction panel, reverse this procedure. O The fluorescent light tube may be replaced at this time. BE CAREFUL NOT TO DROP IT. REMOVE TOP BRKT. & SLIDE HEADER UP
WARNING: If you drop a fluorescent tube and it breaks, IT WILL IMPLODE! Shattered glass can fly six (6) feet or more from the implosion. Use care when replacing any fluorescent tube.

D Replacing the fluorescent light tube starter. See Figure 2-16. Be sure the power to the game has been turned off. Grasp the starter (it is on the back of the mounting bracket), give it a quarter turn, and remove it from its socket. To replace the fluorescent light tube starter, reverse this procedure. 0 Replacement of the fluorescent tube mounting bracket assembly. Be sure the power is off to the game. Disconnect it from its power cable. Remove the screws which secure it and gently Slide it out the front of the cabinet, being careful not to catch its power cable on anything. To reinstall the fluorescent tube mounting bracket assembly, reverse this procedure. O Replacing the speaker. Be sure the power is off to the game. Remove the attraction panel and disconnect the speaker from its cabling. Remove the nuts and bolts which secure the speaker and speaker grill in place and set them and the speaker grill aside. Once the bolts which secure the speaker in place are removed, the speaker may be removed through the opening where the attraction panel was. Reverse this procedure to reinstall the speaker. Figure 2-15 Opening the Attraction Panel — Upright

Page 19

FLUORESCENT _ TUBE STARTER EON

4 TURN TO REPLACE

Figure 2-16 Replacing Fluorescent Tube Starter

O To service the light bulbs and their mounting board: Turn the power to the game back on so you can REMOVE TOP see which bulbs are burnt out. BRKT. & SLIDE Mark the burnt out bulbs and turn the power to HEADER UP the game back off again. To replace the burnt out bulbs, grasp them gently and pull straight out. The new bulbs are gently pushed into the empty sockets. To completely replace the light bulb mounting board: Open the cabinet rear access door and unplug the mounting board from its power cable. Remove the screws that hold the mounting board to the cabinet. Gently slide the mounting board out the front of the cabinet being careful not to catch its cable on anything. To reinstall the above removed items, reverse this procedure. O To replace the speaker. Be sure the power is off to the game. Disconnect the speaker from its cabling. Remove the nuts and bolts securing the speaker. Slide the speaker out through the rear access door. To reinstall the speaker, simply reverse this Procedure.

  • THE COCKTAIL MODE HAS NO BACK-LIT ATTRACTION PANEL. Figure 2-17 Opening the Attraction Panel — Mini
Page 20

Il. Technical Troubleshooting

Introduction

The most common problems occur in harness components such as the coin acceptor, player controls, interconnecting wiring, etc. The TV monitor and PCB computer cause their share of problems too, but not as much as the harness and its component parts. TV monitor troubleshooting will not be covered here because it is covered in that section of this manual. As you already know, the PCB computer is a complex device with a number of different circuits. Some circuits remain basically the same among games, but overall there are a great many differences between them. PCB troubleshooting procedures, therefore, can be lengthy and will differ greatly among games. However, some basic Z-80 CPU information is involved in this section.

General Suggestions

The first step in any troubleshooting procedure is correctly identifying the malfunction’s symptoms. This includes not only the circuits or features malfunctioning, but also those still operational. A carefully trained eye will pick up other clues as well. For instance, a game in which the computer functions fail completely just after money was collected may have a quarter shorting the PCB traces. Often, an experienced troubleshooter will be able to spot the cause of the problem even before opening the cabinet. After all the clues are carefully considered, the possible malfunctioning areas can be narrowed down to one or two good suspects. Those areas can be examined by a process of elimination until the cause of the malfunction is discovered.

oa

Harness Component Troubleshooting

Typical problems falling in this category are coin and credit problems, power problems and failure of individual features.

3-1 NO GAME CREDIT For example, your prospective player inserts his quarter and is not awarded a game. The first item to check is if the quarter is returned. If the quarter is returned, the malfunction most certainly lies in the coin acceptor itself. First, use aset of test coins (both old and new) to ascertain that the player's coin is not undersize or underweight. If your test coins are also returned, coin acceptor servicing is indicated. Generally, the cause of this particular problem is a maladjusted magnet gate. Normally, this will mean slightly closing the magnet gate a little by turning the adjusting screw out a bit (see section on coin acceptor for more details). If the quarter is not returned and there is no game credit, the cause of the malfunction may be in one of several areas. First try operating the coin return button; if the coin is returned, the problem is most likely in the magnet gate. Enlarge the gap according to the coin acceptor service procedures. If this does not cure the problem, remove the coin acceptor, clean it and perform the major adjustment procedure. If the trapped coin is not returned when the wiper

lever is actuated, you may have an acceptor jammed

by a slug, gummed up with beer, a jammed coin chute, or mechanical failure of the acceptor mechanism. In this case, first check for the slug that will generally be trapped against the magnet. If so, simply remove the slug and test the acceptor. If the chute is blocked, remove the acceptor and remove the jammed coins. If there is actual failure of the acceptor, remove the unit and repair as indicated in the coin acceptor service procedures. If the coin is making its way through the acceptor (that is, falling into the coin box), yet there is still no game credit, you either have a mechanical failure of the coin switch or electrical failure of the coin and credit circuits. The first place to begin is by checking the coin switch. Most of these switches are the make/break variety. of micro switch, which is checked by testing for continuity between the NO, NC, and C terminals. When not actuated, the NC and C terminals should be continuous and the NO terminal open. When operated, the NO and C terminals should close and the NC should be open. If the coin switch checks out, examine the connections to the terminals to make sure there is good contact. If necessary, use the continuity tester and check from the terminal lug on the switch to the associated PCB trace. This will tell you if there is a continuous line all the way to the credit circuit.

Page 21

\f the coin switch wires do not check out, the probiem is in the computer — most likely in the coin and credit circuitry. If you do get game credit when a coin is deposited, but the game will not start when the start switch is pressed, you may have a problem in the start switch, the interconnecting wiring or in the computer. First check the switch. If the switch is OK, proceed to check the wiring. Again, make sure you go from the terminal lug on the switch to the PCB trace. This way, you will check the terminal contact as well as PCB edge connector contact. If the wiring is continuous, proceed to check the PCB credit circuit. If not, check each section of the wiring, until the discontinuity is located. If the wiring is OK, the problem must lie in the computer.

Transformer and Line Voltage Problems

Your machine must have the correct line voltage to operate properly. If the line voltage drops too low, a circuit in the computer will disable game credit. The point at which the computer will fail to work will vary some from game to game, but no game will work on line voltage that drops below 105 VAC. Low line voltage may have many causes. Line voltage normally fluctuates a certain amount during the day as the total usage varies. Peak usage times occur mainly at dawn or dusk, so if your machine’s malfunction seems to be related to the time of day, this may be a factor. A large load connected to the same |ine as the game (such as a large air conditioner or other device with an exceptionally large motor) may drop the line voltage significantly when starting up. This drop can result in an intermittent credit problem. In addition, poor connections in the location wiring, plug, or line cord may aiso cause a significant drop in power. Cold solder joints in the game’s harness, especially in areas like the transformer connections, interlock switch, or fuse block, may also produce the same results, although probably on a more permanent basis. Sometimes location owners (especially in bars) replace light switches with dimmer rheostats, and the game is sometimes on the same line. Obviously, the voltage available to the game is going to drop dramatically when the dimmer is turned. In any case, the way to check for correct line voltage is with your VOM. Set the VOM to 250 VAC and stick the probes in the wall receptacle. If it's OK here, check the transformer primary connections. if you do not get 117 VAC, examine the solder joints on the transformer, fuse block, and interlock switch. If you do get 117 VAC, the problem must be either in the transformer, harness connections, or in the PCB power supply. \f you suspect the transformer, check its secondaries with the VOM set to 50 VAC and correlate the readings with the legend on the side of the transformer. The transformer must also be correctly grounded, so check the ground potential as well, especially if there is a hum bar rolling up or down the TV screen.

HARNESS PROBLEMS Other harness problems include blowing fuses and malfunctioning controls. The repeating blown-fuse problem -can sometimes be quite exasperating to solve, for short circuits have the tendency tooccurin areas almost impossible to find. First, try inserting a new fuse, as old fuses age and blow without cause. If the new one also blows, you definitely have a short. The best way to approach this problem is by turning the power off and disconnecting devices that may be causing the problem, such as the TV, transformer, and PCB. Disconnect the devices by pulling off their connectors, but do not allow them to touch. If necessary, insulate them with small pieces of electrical tape. Then, connect your VOM across the terminals of the fuse block (all electrical power shut off), and set it to one of the resistance scales. This will save blowing a fuse each time you want to check the circuit. lf the VOM reveals that disconnecting the devices removed the short, reconnect the devices one by one until the short returns. The last device connected is the one that is at fault. If the VOM reads a short even after the devices are disconnected, the fault must lie in the harness itself, and only patient exploration will reveal its location. First, carefully examine ali the wiring, looking for terminals that may be touching, metal objects such as coins shorting connections or burned insulation. If necessary, use the VOM to check each suspected wire. MALFUNCTIONING CONTROLS One of the most common problems here is a bad potentiometer. Typically, a bad pot will cause the image to jump as it reaches a certain point. The only cure for this one is to install a new pot. If a feature that is operated by a switch (for example, joysticks, foot pedals, control panel buttons) does not operate at all, check the switch with a VOM or continuity tester to verify its operation. If the switch does not check out, replace it. If the switch is OK, you should suspect the input to the switch from the PCB. In this case, get out the harness and logic schematics and check to see what kind of input itis. In many cases, the input will be +5 VDC. If so, use the VOM to check its presence. Normally, the switch is used to pull a +5 VDC line LOW to GND or to pulla LOW line HIGH. If the PCB output is missing, check the wire length from the PCB. If you find the signal at the PCB trace, the wire length or connection is at fault. If not, begin exploring the PCB using the logic schematics.

Page 22

A Glossary of Microprocessor Terms

MICROPROCESSOR — one or several microcircuits that perform the function of a computer's CPU. Sections of the circuit have arithmetic and comparative functions that perform computations and executive instructions. CPU — central-processing unit. A computing system’s “brain”, whose arithmetic, control and logic elements direct functions and perform computations. The microprocessor section of a microcomputer is on one chip or several chips. PROM — programmable read-only memory. User permanently sets binary on-off bits in each cell by selectively fusing or not fusing electrical links. Nonerasable. Used for low-volume applications.

EPROM — erasable, programmable, read-only memory. Can be erased by ultraviolet light bath, then reprogrammed. Frequently used during design and development to get programs debugged, then replaced by ROM for mass production.

ROM — read-only memory. The program, or binary

on-off bit pattern, is set into ROM during manufacture, usually as part of the last metal layer put onto the chip. Nonerasable. Typical ROM'’s contain up to 16,000 bits of data to serve as the microprocessor’s basic instructions. RAM — random-access memory. Stores binary bits as electrical charges in transistor memory cells. Can be read or modified through the CPU. Stores input instructions and results. Erased when power is turned off. “ LSI — large scale integration. Formation of hundreds or thousands of so-called gate circuits on semiconductor chips. Very large scale integration (VLS) involves microcircuits with the greatest component density. MOS — metal-oxide semiconductor. A layered construction technique for integrated circuits that achieves high component densities. Variations in MOS chip structures create circuits with speed and low-power requirements, or other advantages (static will damage a MOS chip).

Page 23

IV. Coin Door Maintenance

SPECIAL NOTE: If you have any questions about the coin acceptors in your game(s), please feel free to contact their manufacturers. Each manufacturer's name is PROMINENTLY imprinted on every acceptor mechanism. Metal mechanisms only: COIN MECHANISMS, INC. 817 Industrial Drive Elmhurst, IL 60126 Phone (312) 279-9150

COIN DOOR MAINTENANCE

METAL COIN ACCEPTOR MECHANISMS

Periodically, the metal coin acceptor mechanism(s) must be removed from the coin door and cleaned.

  • Make sure the power to the game is off.
  • Unlock and open the coin door.

TO REMOVE PUSH LATCHES DOWN

PLACE PEGS IN SLOTS TO REPLACE PULL MECHANISM OUT Metal and Plastic mechanisms: COINCO COIN ACCEPTORS, INC. 860 Eagle Drive Bensenville, IL 60106 Phone (312) 766-6781

  • Remove the coin acceptor mechanism as shown in Figure 4-1. O Push down on the two spring loaded latches. G While holding the latches down, pull the top of the coin acceptor mechanism toward you. 0 Release the latches and lift out the coin acceptor mechanism.

PUSH MECHANISM IN

Figure 4-1 Removing & Replacing the Coin Acceptor

Page 24
  • Clean the magnet of all foreign particles. See 7. To lubricate the coin acceptor: Figure 4-2. Use ONLY powdered graphite and put it ONLY O This may be accomplished by swinging the on the moving parts of the coin acceptor. These gate open as shown in the above figure. parts are called out in Figure 4-3.
  • Remove the cradles and undersize levers and O Be extremely careful to keep the powdered clean the bushings. (A pipe cleaner makes a good graphite away from paths that are traveled by bushing cleaner.) the coins. D Also clean the pivot pin.
  • Whenever needed, the coin acceptor should be cleaned with hot water and cleanser in the follow- — WARNING — ing manner: DO NOT USE OIL © Place the coin acceptor in boiling water for TO LUBRICATE THE F min Pon TEES COIN ACCEPTOR. about ten minutes.
CAUTION: BE CAREFUL NOT TO BURN YOUR-

SELF. & Check the coin chute for obstructions such as:

O Next, use a brush and kitchen cleaner to Paper, gum, etc. remove all remaining foreign matter from the 9. Reinstall the coin acceptor to the coin door. See unit. Figure 4-1. O Rinse the coin acceptor in clean boiling water. O Place the two pegs at the coin acceptor’s base O Dry the coin acceptor thoroughly by using into their retaining slots. filtered compressed air to blow it dry. O Now push the top of the coin acceptor toward j ae the coin door until it snaps in place and is held

NOTE: The reason we recommend using boiling + . water is that it evaporates faster than cold water there by the two spring loaded latches. and speeds drying time. 10. Close and lock the coin door.

APPLY POWDERED GRAPHITE HERE

GATE OPEN AS SHOWN CLEAN MAGNET BY DRAGGING A SCREWDRIVER BLADE ACROSS SURFACE CRADLE

Figure 4-2 Cleaning the Metal Coin Acceptor Figure 4-3 Lubricating the Metal Coin Acceptor

4-2

Page 25

SQUEEZE PINS TOGETHER TO UNLOCK SWING BOTH GATES OPEN

HOLDING BOTH GATES TOGETHER, PUSH UP AND PULL OUT

Figure 4-4 Opening the Plastic Coin Acceptor

PLASTIC COIN ACCEPTOR MECHANISMS

The plastic coin acceptor mechanism(s) must be removed periodically from the coin door and cleaned.

1, Make sure the power to the game is off.

  • Unlock and open the coin door.
  • Remove the coin acceptor mechanisms(s) as shown in Figure 4-1. Push down on the two spring loaded latches. O While holding the latches down, pull the top of the acceptor mechanism toward you. O Release the latches and lift out the mechanism.
  • Squeeze the two pins indicated in Figure 4-4 together to open the mechanism and break itdown into its three basic parts. OD Clean the mechanism in hot soapy water. It never rusts. O Rinse the mechanism in clean hot water and allow it to dry. O Reassemble the mechanism (it never needs lubrication).
  • Check the coin chute for obstructions such as: paper, gum, etc.
  • Reinstall the coin acceptor to the coin door. See Figure 4-5. O Place the two pegs at the coin acceptor's base into their retaining slots. © Now push the top of the coin acceptor toward the coin door until it snaps in place and is held there by the two spring loaded latches.
  • Close and lock the coin door.
NOTE: See Figure 4-6 for instructions on how to set the plastic coin acceptor mechanisms to either accept or reject Canadian quarters.

4-3

Page 26

ACCEPTOR CAN BE SET TO ACCEPT U.S. QUARTERS ONLY OR BOTH U.S. AND CANADIAN QUARTERS.

MAGNET

SY

SLIDE MAGNET TO EXTREME RIGHT (AS SHOWN) TO ACCEPT BOTH U.S. AND CANADIAN QUARTERS.

TO ACCEPT U.S. QUARTERS ONLY, SLIDE MAGNET TO EXTREME LEFT.

Figure 4-5 Changing the Plastic Coin Acceptor to Accept American or Canadian Quarters

4-4

Page 27

PLEASE NOTE:

THE INFORMATION CONTAINED !N THIS SECTION IS TOLD IN AN EASY TO UNDERSTAND MANNER AND IS INTENDED TO AID THOSE WITHOUT AN ELECTRONICS DEGREE IN TROUBLESHOOTING AND REPAIRING THEIR GAMES T.V. MONITOR.

IF YOU READ THROUGH THIS SECTION AND STILL HAVE QUESTIONS, PLEASE CONTACT YOUR DISTRIBUTOR OR MIDWAY MANUFACTURING COMPANY AT THE TOLL. FREE NUMBER PROVIDED WITH YOUR GAMES PAPERS.

OUR STAFF AND OUR DISTRIBUTORS STAND READY TO HELP YOU!

THANK YOU

Introduction: (How to

use this section of your manual.)

This section has been designed to simply familiarize you with one of the more mystical components in your game — the T.V. monitor. If you are an electronics technician who is quite knowledgeable on the subject, you may decide to just go to the schematics and start troubleshooting the defective monitor. But if you are like most people, a monitor is a T.V. set, and that means a complex doo-dad that means big buck repairs. This isn’t necessarily so. This section of the manual will acquaint you with the monitor and could just help you repair it if you feel adventurous enough to give it a try. If you have any knowledge of electronics, especially the use of a voltmeter, the repairs you can make are astonishing. Just keep in mind that ELECTRICITY CAN BE VERY DANGEROUS, SO BE CAREFUL!

If you want to understand how a monitor works, just read the “THEORY OF OPERATION” subsection. If you wish, you can follow along with the schematics. The information is presented in a very basic manner but a more complete treatment of the subject can be found in the technical sections of bookstores.

If you want to attempt to repair your monitor, it would be a good idea to read this whole section beginning to end before starting. Pay attention to all warnings and take them seriously. The more equipment you have the better, but a low cost Volt-Ohm-Milliameter can often do the trick. Here are the steps to take:

  • Find the symptom that matches the problems your monitor has in the “SYMPTOM — DIAG- NOSIS” subsection. The diagnosis tells the circuit or area the problem may be in and possibly even the actual component causing it. Once you have the circuit that is causing the trouble, read the “TROUBLESHOOTING” subsection to learn- the procedure for finding the bad part. . Next, go to the schematic section and find the schematic that matches your monitor. It may be helpful to read the “DIFFERENCES BETWEEN MONITORS” subsection if you are unsure of which monitor you have. Use the schematic to see what parts are in the offending circuit.

That really is all there is to it. Just remember that there are some bizarre or rare symptoms not covered, or that a monitor may have two or more different problems that only a genius, the experienced, or an experienced genius can figure out. But be patient, follow safety precautions, and remember that there is also literature available from the monitor companies through your distributor or from Bally Midway Manufacturing Company on request. (There is a toll free number on the back side of the front cover of this manual.)

Page 28

Symptom Diagnosis

  • Insufficient width or heighth: A. Horizontal line (due to VERTICAL CIR- CUIT DEFECT). Bad yoke. O Bad vertical output section. D Open fusible resistor in vertical section. O Bad height control. O Bad flyback. B. Vertical line (due to HORIZONTAL CIR- CUIT DEFECT). O Bad yoke. O Open width coil. O Open part in horizontal output section.
  • Picture spread out too far or crushed in certain areas: A. Horizontal or vertical output transistor. B. Bad Component in output circuitry. C. Vertical linearity or damper control needs adjustment.
  • Line too close with black spacing: A. Problem in vertical section causing poor linearity.
  • Poor focus and convergence: A. Bad high voltage transformer (‘‘flyback”) or control. B. Focus voltage wire not connected to neckboard terminal.
  • Colors missing; check: Interface color transistors. Color output transistors. Cracked printed circuit board (neck Board). Color circuits. Video input jack. Defective picture tube.
  • Picture not bright enough: A. Weak emission from picture tube.
  • Silvery effect in white areas; check: A. Beam current transistors. B. Weak picture tube emission.
  • Too much brightness with retrace lines; check: A. Beam limiter transistors. B. Brightness and/or color blanking control set too high.
  • Increasing brightness causes an increase in size and poor focus. A. Weak high voltage rectifier or regulation (high voltage unit). B. Bad component in monitor's power supply. mmMoOOD>

5-2 10.

11.

12,

13.

14,

15.

16.

17.

18.

19. Small picture and/or poor focus: A. Low B+ voltage (power supply trouble).

Vertical rolling: A. Vertical oscillator in the IC, vertical sync. transistor, or circuit. B. No sync from logic board. C. Three pin sync. jack is loose or plugged in wrong. Horizontal line across center: A. Vertical output circuit is dead (see symptom No. 1. A.). B. Vertical oscillator is not putting out the right wave form. Picture bends: A. Horizontal sync needs adjusting. B. Magnetic or electromagnetic interference. Flashing picture, visable retrace lines: A. Broken neck board. B. Internal short circuit in the picture tube (arcing). Unsymmetrical picture or sides of picture: A. Defective yoke. No brightness, power supply operating — No high voltage for the picture tube; check: A. Horizontal oscillator. B. Horizontal amplifier and output. C. Flyback transformer (high voltage unit). No brightness, high voltage present; check: A. Heater voltage to the tube at the neck board. B. Screen-grid voltage for the tube. C. Focus voltage. D. Grid to cathode picture tube bias. No high voltage; check: A. For AC input to the “flyback”. 8B. Horizontal deflection stages. C. Flyback transformer. D. Yoke. E. Power supply.

No horizontal and vertical hold; check: A. Sync transistors and circuit. B. Wires and jack from logic board to the monitor. Wavey picture — (power supply defect); check: A. Transistors, diodes, electrolytic capacitors in the power supply.

Page 29
  • Moving bars in picture: A. Ground connector off between monitor and logic boards. B. Defect in the power supply (see wavy picture symptom).
  • Washed out picture (see picture not bright enough): A. Check video signal at the cathode pins with an oscilloscope. If there is about 80 volts peak to peak, the picture tube has weak emission.
  • Monitor won't turn on: A. Problem in the power supply: Check fuse, transistors, open fusible resistor.

B. Shorted horizontal output transistor. C. Defective high voltage disabling circuit. D. Crack(s) somewhere on main chassis board.

  • Can't adjust purity or convergence:

A.

9 OD

mm Use a degausser to demagnetize the picture tube carefully following your degausser’s instructions. Picture tube defective. Nearby equipment is electromagnetically interferring. The poles of the earth are pulling off the purity — see “A” above. Poor focus or width of picture. Make sure you have the correct CRT number for that brand of monitor.

Guide To Schematic Symbols

THERMISTOR (POLARITY DOESN'T MATTER)

SY WL INDUCTOR, COIL, CHOKE (POLARITY DOESN'T MATTER)

{-) CATHODE

(+) ANODE

ZENER DIODE

5-3 IRON CORE TRANSFORMER (SUCH AS A FLYBACK)

Ls

FUSE (POLARITY DOESN'T MATTER)

CATHODE (-)

ANODE (+)

DIODE

Page 30

COLLECTOR Te COLLECTOR - BASE ————~ BASE ————- EMITTER — EMITTER TE

NPN TRANSISTOR PNP TRANSISTOR

' Wwn—

VARIABLE RESISTOR, POT, CONTROL RESISTOR

(POLARITY DOESN'T MATTER) (POLARITY DOESN'T MATTER)

+ +

LINES ARE CONNECTED ELECTROLYTIC CAPACITOR

LINES ARE NOT CONNECTED CAPACITOR (POLARITY DOESN'T MATTER)

hg = GROUND

5-4

Page 31

Troubleshooting

Troubleshooting monitors requires experience, patience, and luck. The first step is to match the symptom the monitor displays to the diagnosis next to it in the “SYMPTOM-DIAGNOSIS” subsection. This will pinpoint the circuit the problem is probably in, and often the parts to check. Next, the circuit should be visually inspected to see if there are any parts broken, burned, or if something is there that shouldn't be, like a loose screw, etc. Some parts go bad before others and should be checked first. In fact, following is the general order in which parts usually go bad:

  • Semiconductors (like transistors, diodes, and integrated circuits).
  • Fusible resistors.
  • Electrolytic capacitors.
  • Resistors.
  • Capacitors and coils. Always remember thata monitor can bite like a snake. Even when it is turned off, capacitors hold voltage and will discharge it to you should you be touching chassis ground. The picture tube or CRT, itself, is a giant capacitor, so avoid the flyback anode plug hole. With the monitor on, the power supply circuit and/or the flyback, which puts out at least 23,000 volts, CAN BE KILLERS! Avoid handling power transistors (usually output transistors) or ICs, yoke terminals, and other high power components when the monitor is on.
WARNING: That picture tube is a bomb! When it breaks, first it implodes, then it explodes. Large pieces of glass have been known to fly in excess of 20 feet in all directions. DO NOT carry it by the long, thin neck. Discharge its voltage to ground by shorting the anode hole to ground. Use a plastic handled screwdriver, connect one end of a wire with an alligator clip at each end to chassis ground and the other end to the metal shaft of the screwdriver. Using ONE HAND ONLY (put the other in your pocket) and touching ONLY the plastic handle of the screwdriver (DO NOT TOUCH THE METAL SHAFT) stick the blade of the screwdriver into the anode hole.
IMPORTANT! The side brackets of the monitor are chassis ground as is the aquadag, the picture tube’s dark conductive coating. BUT, on the ZENITH MONITOR there are metalic mounting parts which ARE NOT chassis ground. Discharging the CRT to these will damage the monitor!

5-5 Be prepared for a fairly loud pop and a flash. The ionger the monitor has been turned off, the smaller the pop and dimmer the flash. But BE CARE- FUL, picture tubes will hold a very healthy charge for at least a week if not longer. Even after you've discharged it once, it may still carry a residual charge. It’s better to be too careful than dead, which is why electronic equipment always carries stickers referring servicing to qualified personne!. Handle the side with the viewing screen against your chest when changing it. ALWAYS wear safety goggles when handling the picture tube. To maintain the safety and performance of the monitor, always use exact replacement parts. For instance, the wrong components in the power supply can cause a fire, or the wrong color transistor may give a funny color to the picture. Service your monitor on a nonconductive firm table like wood, NOT METAL, and take off all of your jewelry just in case. With all this in mind, you are ready to begin troubleshooting.

Observe the picturg carefully. Try to vary the appropriate control that would most likely affect your particular symptom. For example, if there is poor brightness or no picture, try turning up the brightness or contrast control. If the controis have no effect at ail, chances are there is trouble with the control itself, the circuit it controls, or a nearby circuit that may be upsetting voltages. Go to the list of symptoms and determine with the schematic where the bad circuit is.

CAUTION:

Keep in mind that capacitors hold a charge as can the picture tube (for at least a week and usually longer), and could shock you.

First, check for obvious visual defects such as broken or frayed wires, solder where it is not supposed to be, missing components, burned components, or cracked printed circuit boards. If everything looks good up to this point, make sure that diodes, electrolytic capacitors, and transistors have their leads connected in the right polarity as shown.on the schematic and the circuit board. Turn on the power and measure the voltages at the leads of the active devices such as tubes, transistors, or integrated circuits. Any voltage that does not come within at least 10% to 15% of the voltage specified on the schematic indicates either a probjem with that device or a component connected with it in the circuit. The next step is to use the ohmmeter to narrow down the field of possible offenders.

Page 32

To test a transistor, one lead of the ohmmeter is placed on the base; and the other lead placed just on the emitter, then on the collector. A normal transistor will read either high resistance (infinite), or little resistance (400 to 900 ohms), depending on the polarity of this type transistor. Then the leads should be switched, one remaining on the base, and the other switched from the emitter to the collector. Now the opposite condition should result: the resistance should be infinite if it was lower when the other lead was on the base. Consistantly infinite readings indicate an open, anda short is demonstrated by 0-30 ohms on most of these test readings. Finally, place one lead on the collector, then the other on the emitter. No matter which lead is used, there should be infinite resistance. Any lower reading, such as 50 ohms (which is typical on a bad transistor), indicates a short. This all sounds pretty confusing, but a little experience on a good transistor will make you an expert in no time. Usually, the lowest ohmmeter setting is used for testing transistors. Once in a great while a transistor may check out good on this test, but may actually be “leaky” or break down only on higher voltages. If in doubt, change it. It is also wise tocheck the transistor out of the circuit just in case some component in the circuit is affecting the onmmeter reading. A diode is tested like a transistor except it only has two leads. Again, there should be high resistance one way and little resistance the other. If it tests bad, take one lead out of the circuit in case some components messing up the ohmmeter reading.

NOTE: DO NOT leave soldering equipment on the leads too long since all semiconductors, especially integrated circuits, are easily destroyed by heat.

Without special equipment, integrated circuits are checked by verifying the proper DC voltage on the pins and the correct AC wave form using an oscilliscope. BE CAREFUL: Shorting their pins can easily destroy them. Resistors are checked with an ohmeter and should usually be within ten percent of the value stated on them and on the schematic. You may have to desolder one lead from the printed circuit board. If you wreck the foil on the board, carefully solder a small wire over the break to reconnect the conductive foil. Capacitors are tricky. Their resistance goes up when checked with an ohmmeter which shows a charging action. As they suck up current from the meter, the voltage goes up and so does the resistance. If you are

sure a particular circuit is giving you a problem and

everything else checks out O.K., Electrolytic capacitors are prime suspects. Substitute a new one and keep your fingers crossed.

Theory of Operation

To understand what goes on inside the monitor, large general groups of circuits will be examined instead of laboriously analyzing the branches and small circuits that make up these groups. This will help avoid confusion and aid in a basic, concrete, knowledge of what makes up a monitor.

THE POWER SUPPLY — The AC going to the monitor from the game transformer is just like the voltage and current from your wall outlet. It jumps up and down going positive and negative sixty times a second. But a monitor needs nice, smooth DC; direct current, not alternating. So diodes chop up the AC and a big electrolytic capacitor filters it out to make it even smoother. Since the monitor is a big piece of electronic equipment, with many circuits demanding a lot of power from the power supply, there are also zener diodes and transistors to help maintain a nice, constant, smooth voltage so that the monitor circuits don’t jump around. And this is what happens when you see a wavy picture. There is AC creeping through the power supply, so it must be malfunctioning. If the voltage from the power supply is too low, the other circuits will be starved for power and you may see a small, wavy picture, or noneatall. Some circuits receive voltages that are higher than what the power supply should put out. But they come from the flyback transformer which will be discussed later.

THE INTERFACE SECTION OF THE CHASSIS — The interface section of the chassis is fairly easy to identify. It is right by the place where the video jack(s) from the logic board{s) plug into. There are sets of transistors that receive the separate red, green, blue, and sync information from the cables that come from the logic boards. The circuits jack up the voltage and match impedances, or in other words, prepare the logic board outputs for the circuits that will really amplify them for the output devices such as the yoke in the case of the sync, or the picture tube that shows the colors.

Page 33

An interesting aside is that our sync is composite negative sync. That means two things:

  • The sync is a negative going wave form.
  • There are two pulses going at different speeds over the same wire: a. Vertical wave forms at 60 times per second (or Hertz) and b. Horizontal wave forms at about 15,750 times per second (Hz). The sync is amplified by a sync amplifier transistor and sent on its way to the oscillators. The syne or timing information will be explained along with the oscillator shortly. The color information is sent via wires to the neck board where the main amplification occurs. This will also be discussed later.

VERTICAL AND HORIZONTAL DEFLECTION— After the sync signal is amplified by the sync amp, it goes to two different sections, the vertical and horizontal circuits. Basically, the sync signals are for timing so the picture doesn’t mess up since it is assembled like an orderly jigsaw puzzle, but so fast that you can’t see the electron beams for each color painting the picture on the screen. This will all become clear soon. For now, we will follow the 60 cycle component of the sync as it goes on its journey to the deflection yoke. The 60 cycle pulse goes to the vertical oscillator to make sure this circuit goes back and forth (or oscillates) at 60 times a second. Without this pulse keeping the circuit at the correct speed, it may get lazy and oscillate at 58 cycles or lower, or get ambitious and oscillate at 62 cycles or higher. At the wrong speed, the picture will start to roll up or down. A Wells Gardner 13” (K4806) or 19” (K4906, K4956) color monitor uses an integrated circuit for its sync section. An Electrohome 13” or 19” color monitor uses an integrated circuit 1C501 for its sync section. The Zenith monitor (CD19MXRFO6) also uses an IC for the sync processing. Wells Gardner uses HA11423, Electrohome uses HA11244, and Zenith uses 221-175 (their part number). These ARE NOT interchangeable! The idea is all the same. The output to the vertical amplifying transistors for all monitors must form a sawtooth wave form, sort of like a bunch of pyramids, racing through the yoke’s vertical coils at 60 times a second.

Along the way to the output transistors, the 60 cycle pulse is shaped and amplified to do the job: the yoke magnetically pushes the electron beam to fill the screen out sideways looking at the screen with the greatest length going up and down. Or viewing the screen sitting like a home television set, the amplified vertical output fills the screen up and down. Watching a monitor like this, seeing only a horizontal line means a problem with the vertical coils of the yoke or

5-7 anything from the vertical output section on back to the oscillator. The horizontal section is very similar with a few exceptions. The horizontal wave shape is more like a square and has a frequency of 15,750 cycles a second. Both Wells Gardner and Electrohome use the other side of their respective integrated circuits for the horizontal circuitry. If the oscillator isn't going at the correct speed, the picture may move sideways, start to slant, or tear up with slanted thin figures. With both the vertical and horizontal of all monitors, there are variable resistors that change the speed of the oscillators up and down. This way you have controls that can make the correct frequencies to keep the electronic jigsaw puzzle nicely locked in place. If you're driving in acarand next to yousomeone else is driving their car at exactly the same speed, it will appear that they are not moving. And this is why the sync frequency and the oscillator’s frequency must match, so the picture doesn’t appear to move. The correct wave form is shaped and amplified in the circuitry just like in the vertical section. But the horizontal output transistor is a large power transistor and not only serves to give current to the horizontal yoke windings, it also feeds the flyback transformer.

THE FLYBACK TRANSFORMER (OR HIGH VOLTAGE UNIT) — The picture tube needs high voltage to light up, and the power supply can’t meet this demand. The flyback transformer receives current alternating at about 15,750 times per second from the horizontal output transistor. The “flyback” jacks up its input voltage and puts out a higher voltage alternating at the same speed. But, in your “flyback” there are diodes that chop up the alternating voltage to make it asmooth DC output just like in the power supply. This is what goes through that thick red wire to your picture tube. THIS AREA HAS ABOUT 24,000 VOLTS ON IT AND IT CAN KILL YOU! The “flyback” may be dangerous, but it is also generous. It has extra output windings which give voltage to the heater pins of the picture tube, voltage for the vertical deflection circuits, and picture tube screen-grid voltage. So in a way, the high voltage “flyback” is like a second power supply. COLOR CIRCUITS — The color circuits are pretty straight forward. The signals go into the interface section where some amplification and impedance matching occurs. These circuits are pretty sparse and simple. Each color just has two transistors and a diode with some resistors and capacitors. From here, the AC color signal is sent by wires to the neck board. The color output circuits are on the neck board. The color signals going to the transistors are controlled by two variable resistors called drive controls. There are only two, one for the red and one for the green on

Page 34

Wells Gardner and Electrohome monitors. Zenith monitors have all three: red, blue and green. The Wells Gardner and Electrohome monitor have another variable resistor in their emitter part of their color output transistors. These “cutoff controls” vary the amount of A.C. signal that the transistor amplifies and sends to the cathodes of the picture tube. The Zenith monitor has its cutoff controls in the interface section to vary the amount of signal going to the output transistors. The more signal, the more color. If you think this is confusing, here is another little hitch. The Electrohome and Zenith monitors both have the actual A.C. picture information signal going through the emitters of the color output transistors. The Wells Gardner has the A.C. signal going to the base of the transistors. The blanking and beam limiting signals which come from the blanking and beam limiting transistors in the interface section go into the color output transistor base in the Electrohome and Zenith monitors, but enters into the emitter of the Wells Gardner monitor's color output transistor. Should you feel adventurous enough to look at this signal on an oscilloscope, it should look like a square. The beam limiter helps control the brightness level, and the blanking transistor rapidly turns the picture tube on and off so that retrace lines don’t show up on the screen. By turning up the brightness on a good monitor, these four to six retrace lines can be seen slanting diagonally across the picture.

PROTECTION CIRCUIT —

To protect the high voltage section against voltages that are too high coming from the power supply which could cause X-rays to be emitted from the “flyback”, a circuit senses the higher power supply voltage and turns off the horizontal oscillator. Since the horizontal oscillator doesn't work, the horizontal output transistor has nothing to feed the “flyback” which in turn has nothing to feed the picture tube. The monitor will be silent, have no picture, and will appear to be off. But don’t be fooled. There is still that excessive amount of voltage coming from the power supply. To find out, check at pin two of Wells Gardner's C501 and emitter of X04 for the Electrohome monitor. Check the 95 volt test point (located near the “flyback”) for the Zenith monitor. Here are the voltages you should receive: Wells Gardner = 130VDC Electrohome = 120VDC Zenith = 95VDC The best place to measure this voltage on an Electrohome monitor is at a pin marked B1 on the chassis. This is because a 13 inch color Electrohome monitor, The GO7-FBO or G07-902, has an integrated circuit and very little else in the power supply. Still, there should be 120VDC at B1. THE PICTURE TUBE (OR CRT) —

ATTENTION! For information on picture tube replacement types, go to the last section, “PICTURE TUBE INTERCHANGEABILITY”.

The picture tube or CRT is an output device. In other words, the end result of the circuit's work is displayed by this part. Actually, the output of other circuits is in the neck of the picture tube. First, there is the heater. The heater boils off electrons from the cathodes so that they (the electrons) shoot up to the screen to excite the phosphors so that the three phosphors emit three colors of light. The cathodes are next, and again they emit electrons to turn on the tube phosphors, making it glow. A defective cathode may cause the particular color it handles to be missing. Next come the grids. The first grid is grounded. The following grid is the screen grid which receives about 300VDC depending on the brightness setting. The next grid closest to the picture tube screen is the focus grid which gets about one fifth the amount of voltage that is applied to the picture tube anode. After jetting from the cathode through all these grids, the electrons speed through a mask, a sheet of material with tiny holes, and then excite the tiny dots of phosphor in the inside surface of the picture tube screen. The green electron gun (or cathode and circuitry) spits out electrons which head for the green phosphors only. The same goes for the red and blue guns. The way the phosphor light blends determines the color seen. Shouid these electron beams become too intense, they may burn the phosphor. With the monitor off, this can be seen as a dark permanent image of the video information on the tube screen.

Differences Between Monitors

The easiest way to identify the brand of monitor you are working with is to find the manufacturer's name or model number printed on the chassis or chassis base. But what if the monitor was in a Texas dust storm or buried in volcanic ash and this information is no longer there? Fear not! Each monitor has its own peculiarities and the following should heip to identify them: The ELECTROHOME G07-904 (19”) and GO7-902

  • have their horizontal and vertical processing IC hidden under a silver can. A shiny metal top behind the “VERTICAL HEIGHT” and “HORIZONTAL FRE- QUENCY” control prove this is an Electrohome monitor.
Page 35

The WELLS GARDNER K4906 (19”) and K4806 (13") have their horizontal and vertical processing IC outin the open directly behind the “VERTICAL HOLD” control. The ZENITH CO19MXRFO6 (19) monitor has its horizontal and vertical processing IC way in back by the picture tube. The monitor also has large white cables going from the main board to the neck board. K4906 (1st TYPE) — This monitor's identifying tags have BLACK ink printed on a white background. There is NO Vertical Damping Control. (This Control would be next to the Vertical Hold Control but this area is jumpered with a small wire instead. K4906 (2nd TYPE) — This monitor's identifying tags have RED ink printed on a white background. There IS a Vertical Damping Control next to the Vertical Hold Control. The Damping Control provides a few more lines on the top of the monitor screen (monitor viewed as a normal T.V. would be) for any video game that may need these lines to fit the picture on the screen. Moving the Control may distort the top part of your picture (or the side, depending onthe game and how the monitor is mounted) so go ahead and move it if you are having this type of problem. To accommodate this new feature, there are a few circuit changes. ONE MAJOR DIFFERENCE BETWEEN THESE TWO VERSIONS OF THE K4906 IS THE YOKE. They look the same but notice the part numbers: K4906 WITHOUT the Damper Control: 2021111201 K4906 WITH the Damper Control: 2021111258 Since the companies like to change part numbers at the drop of a hat, the best thing to do is to request whatever part number is written on your yoke. If you should get the wrong yoke, the results will be: Picture distortion. Excessive brightness. Too much or too little vertical picture size.

CONTROLS YOU MAY NOT TOUCH Basically, on the Electrohome monitor, you can move any control you want EXCEPT for the B1 control. This sets the power supply voltage (ideally at 120 VDC) and is located right behind VERTICAL HOLD. The 13” Electrohome DOES NOT have this control. It may also be wise not to move the VERTICAL LIN- EARITY since this distorts the picture and is hard to reset perfectly. If you do move it, turn on the Cross Hatch Test Pattern of your game and try to get the squares to the point where they are equal in size by readjusting this Linearity Control. On the Wells Gardner monitor, brightness is adjusted by the “BLACK LEVEL” Control which is right next to the Horizontal Frequency Control. Under the Focus Control is the “SCREEN” Control which youDO NOT touch. Yes, this control does adjust the brightness, but it is used to set the CRT bias and is adjusted at the factory. When Wells Gardner sets it, they mark the position with a black mark on the knob. If you moveit, be sure to realign the mark and THEN set the BLACK LEVEL Control to the brightness you desire. So, other than the SCREEN control, you may adjust any of the controls. The Zenith monitor has a 95 volt adjustment control. It is green and located behind the jack labeled 3D3. To discourage you from moving it, Zenith has placed a little glue on top of this control.

Parts Interchangeability

Some parts can be interchanged on all of the monitors. Here are the rules:

  • You CAN swap any resistor between monitors that has the same resistance, wattage rating, and tolerance. You CAN swap any capacitor between monitors that has the same capacitance and voltage rating.

. You CAN swap many of the parts between the 19" and the 13” versions of each manufacturer's monitor. BUT, be certain to compare the manufacturers’ part numbers to be positive the parts you want to interchange are identical. BE SURE you have read the section DIFFERENCES BE- TWEEN MONITORS which was covered earlier.

You MAY BE ABLE to swap picture tubes between monitors. In the past you could swap any picture tube, but due to rampant engineering changes and new monitor models being introduced, you would need a computer to keep track of what could be swapped. For more information on this subject, go to “PICTURE TUBE INTERCHANGEABILITY”.

You CANNOT change any part that is a safety part, one that is shaded in gray on the schematic; it MUST be IDENTICAL to the original. To do otherwise IS DANGEROUS. For instance, the 13 inch Electrohome (G07-902) monitor “flyback” looks identical to the 19 inch Electrohome (G07- 904) monitor “flyback”. In fact, there is evena 19 inch Electrohome (G07-905) monitor (which is an obsolete model) with a similar looking “flyback". NONE OF THESE ARE INTER- CHANGEABLE!

You CAN change any of the parts between the G07-904 and GO07-907. They're essentially the same monitor except that the G07-907 has a vertically mounted picture tube.

Page 36

If there is any doubt about what parts can be swapped between each manufacturer's 19 inch and 13 inch models, compare the manufacturer's part number between each one. If they match up, they are the same part.

Picture Tube Interchangeability

13” MONITORS There are currently two 13" monitors being used: the Wells Gardner K4806 and the Electrohome G07-902. The picture tubes used are NOT interchangeabie. The pins on the neck of the CRT will not fit in the socket should you use the wrong CRT. Here is a chart for ail the 13” color monitors Bally Midway uses. ELECTROHOME _ G07-902 — 370ESB22 WELLS GARDNER K4806 —370KSB22

19” MONITORS Here it gets a little tricky. All of the picture tubes will fit no matter which is used. But if you use the wrong one, you. will have problems with purity and/or dynamic convergence. Purity trouble means that the color won't be true. If you turn up the color control for one color, instead of seeing that Solid color it will show blotches or blobs of other colors on the screen.

Trouble with dynamic convergence means that there will be color fringing around solid lines at the edges of the screen.

The only way to ensure that you avoid these problems is to get the right picture tube or the right substitute.

Here is a list of the 19” monitors and the CORRECT

CRT numbers. ALL ELECTROHOME G07-904 — 19VMNP22 RCA 19VMJP22 RAULAND 510UJB22 HITACHI WELLS GARDNER K4906 — I9VLTP22 RCA 19VMLP22 ZENITH J9VMKP22 PHILLIPS

ZENITH CD19MXRFO6 — 1I9VMLP22 ZENITH I9VLTP22 RCA 19VMKP22 PHILLIPS The factory recommended CRT type could change in the future for one reason or another, but the listed picture tubes will work. As a matter of fact, you can call another picture tube company to see if they have a replacement number to recommend.. .but caveat emptor — {et the buyer beware.

5-10

Page 37

Power Supply Yoitage and Symbois

Symbol | Voltage Operating Circuit

@|tv| Vert. Ose.

| | Syne Blanking | | CRT Cut-off

eR|130v | Horiz, Ose.

| Horz, Drive | Horz. Output i Vert. Output

| ,

1d)|175V_ | Video Output

Q351 COLLECTOR

1VIDIV 200uSECIDIV 20VIDIV 10uSECIDIV

TP-31 DC COUPLED 94023 BOTTOM LINE =0 VDC

2VIDIV 200MSECIDIV SVIDIV 20uSECIDIV

LC, 301, PIN 3 F

VOTH

cael mr]

1VIDIV SMSECIDIV 1VIDIV 20u SECIDIV

Tp82 TP.31, AC COUPLED

20VIDIV SMSECIDIV 1VIDIV 200uSEC/DIV

1.C. 301, PIN 13 NEGATIVE SIDE OF C303,

1VDIV 200uSECIDIV 2VIDIV SMSECIDIV O.5IDIV SMSECIDIV

O.5/DIV 20u SECIDIV

LC. 301, PIN 15

2VIDIV 10uSECIDIV

F

1VDIV 2MSECIDIV |). THIS PRODUCT CONTAINS CRITICAL |) ELECTRICAL AND MECHANICAL PARTS -

ESSENTIAL FOR X-RAY RADIATION

FOR REPLACEMENT PURPOSES, USE ONLY TYPE PARTS SHOWN 19” COLOR MONITCR SCHEMATIC DIAGRAM MODELS 19K4901, 19K 4906, 19K4951, 19K 4956 A “Ls

IN THE | : —

CAUTION: FOR CONTINUED SAFETY, REPLACE SAFETY GRITICAL COl PONENTS ONLY WITH MANUFAC- TURES'S RECOMMENDED PARTS. AVERTISSEMENT: POUR MAINTENIR LE DEGRE DE SEGURITE DE L'APPAREIL NE REMPLACER LES COMPOSANTS DONT LE FONCTIONNEMENT EST CRITIQUE POUR LA SECURITE QUE PAR DES PIECES RECGMMANDEES PAR LE FABRICANT,

o202 2scie15+/ st BSt545 pe R204 owe 9209 lesciaisy /

|[sync.ame [esciéisyvo Feces

Jezes $0 |cooseiaey 11 ‘c= ri E39 HOR RIVE 2scesezsK ~) zsCzsiosK

|e 360 OSCILLOSCOPE WAVEFORM PATTES The waveforms showin are as observed on the wide banc oscilloscope with the moniior turned to a reasonably strong signal and a normal picture. The voltages shown on each waveform are ihe approximate peak ampli: tudes. if the waveforms are observed on the oscilioscope wit! a poor high frequency response, the corner of pulses wiil tend to be more rcunded than those showr and the ampiitude of any high frequency pulse tend to be less.

401 02, aeo'our _geteN Gur shoe bur 28C2050.8/ BK 25020681 8/LBEK 25C2060 81 68K| 2SCIBIBBVC/CvE 2SCIBISBVECVC 2SCIBIABVE-CVC

(FOR CENTERING] H.V.UNIT 7382

  • K4901D, K4906D, K4951D 5833 k49568 rr “40
Page 38

REPLACEMENT PARTS LIST This monitor contains circuits and components included specifically tor safety purposes. For continued protection no changes should be made to the originai design, and components shown in shaded areas of schematic, or A* on parts list should be replaced with exact factory replacement parts. The use of substitute parts may create a shock, fire, radiation or other hazard. Service should be performed by qualified personnel only.

MAIN BOARD

Ref. No.Part No.DescriptionRef. No.Part No.Description

RESISTORS RESISTORS (CONT.)

R201203X6500-6451K Ohm, 5%, 1/4W CarbonR369203X5602-329680K Ohm, 5%, 1/2W Comp.
R202203650052330 Ohm, 5%, 1/4W CarbonR370203X6501-00233K Ohm, 5%, 1/4W Carbon
R203203x6500-405100 Ohm, 5%, 1/4W CarbonR371203X9014-5841K Ohm, 5%, 1W Metal Oxide
R204203X6700-327100 Ohm, 5%, 1/2W CarbonR372203%9101-11912K Ohm, 5%, 1W Metal Oxide
R205203X6700-421270 Ohm, 5%, 1/2W CarbonR375203X6700-7636.8K Ohm, 5%, 1/2W Carbon
R206203X6500-540390 Ohm, 5%, 1/4W CarbonR376203X9104.404270 Ohm, 5%, 2W Metal Oxide
R207340X2201-934200 Ohm, 5%, 1/4W CarbonR377203X6500-447150 Ohm, 5%, 1/4W Carbon
F208203X6500-540390 Ohm, 5%, 1/4W CarbonR378203X6500-88610K Ohm, 5%, 1/4V¥ Carbon
R209340X2201-934200 Ohm, 5%, 1/4W CarbonR379203X6500-88610K Ohm, 5%, 1/4W Carbon
R210203X6500-540390 Ohm, 5%, 1/4W €arbonR380203X6500-865,&2K Ohm, 5%, 1/4W Carbon
R211340X2201-934200 Ohm, 5%, 1/4W CarbonR381203X6500-7242.2K Ohm, 5%, 1W Metal Oxide
Rota203X6500-6451K Ohm, 5%, 1/4W CarbonR383203X8014-387150 Ohm, 5%, 1W Metal Oxide
R215203X6501-126100K Ohm, 5%, 1:4W Carbon502203X6500-88610K Ohm, 5%, 1/4W Carbon
R216203X6500-645,1K Ohm, 5%, 1/4W Carbon503204X 1700-535150 Ohm, 5%, 15W Metal Oxide
R217203X6500-405100 Ohm, 5%, 1/4W CarbonR504203x9014-26747 Ohm, 5%, 1W Metal Oxide
R218203X6500-6451K Ohm, 5%, 1/4W CarbonR505203X6501-2092.2K Onm, 5%, 1/4W Carbon
R219203X6501-126400K Ohm, 5%, 1/4W CarbonR506203x9104-10515 Ohm, 5%, 2W Metal Oxide
R220203X6500-6451K Ohm, 5%, 1/4W CarbonR507203X5602-185,330K Ohm, 5%, 1/2W Comp.
R221203X6500-405100 Ohm, 5%, 1/4W CarbonA*R601204X1625-0583.3 Ohm, 5%, 10W WW
R222203X6500-7623,3 Ohm, 5%, 1/4W CarbonR701203x9105-1412.2 Ohm, 5%, 2W Metal Oxide
R224203X6500-16910 Ohm, 5%, 1/4W CarbonR702203X6206-4412.2 Ohm, 5%. 1/2W Carbon
R225203X6500-169,10 Ohm, 5%, 1/4W Carbonvr201204x2070-072,2K Ohm-B Semi-Fixed
R226203X6500-16910 Ohm, 5%, 1/4W CarbonR301204x2070-0845K Ohm-B Semi-Fixed
R227203X6501-04447K Ohm, 5%, 1/4W CarbonR303204X2070-055,500 Ohm-B Semi-Fixed
R228203X8500-6451K Ohm, 5%, 1/4W CarbonR351204x2070-0722K Ohm-8 Semi-Fixed
R229203X6700-421270 Ohm, 5%, 1/2W CarbonVR352204x2070-0722K Ohm-B Semi-Fixed
230203X6500-8638.2K Ohm, 5%, 1/2W Comp.
R231203X6500-8638.2K Ohm, 5%, 1/2W Comp
Ras203X6500-8638.2K Ohm, 5%, 1/2W Comp.
233,203X6500-468180 Ohm, 5%, 1/4W Carbon
R234340X2820.93482 Ohm, 5%, 1/4W CarbonCAPACITORS
R235340X2820-93482 Onm, 5%, 1/4W CarbonC201203X0014-0881000 uF, 16V, Electrolytic
R236340X2820-93482 Ohm, 6%, 1/4W Carbon202202X7200-064330 pF, 500V, Ceramic
R301203X6500-508270 Ohm,5%, 1/4W CarbonC203202X7200-043220 pF. 500V, Ceramic
R302203x6500-863,8.2K Ohm, 5%, t/4W CarbonC204202X7200-043220 pF, S00V, Ceramic
R303203X6500-8638.2K Ohm, 5%, 1/4W Carbon0205203X0014-076470 uF, 16V, Electrolytic
R304203X6500-7242.2K Ohm, 5%, 1/4W CarbonC208203X1810-1490.1 uF, 125V Mylar
R305203X6500-842§.8K Ohm, 5%, 1/4W CarbonC207349X2232-109022 uF, 100V Mylar
R306203X6003-2017.8K Ohm, 2%, 1/4W Carbon301203X0014-065330 uF. SOV Electrolytic
R307203X8500-8255.6K Ohm, 5%, 1/4W Carbon302203X 1600-5630.033 UF, 50V Mylar
R309203X6500-96522K Ohm, 5%, 1/4W CarbonC303203x0629-0373.3 uF, 50V Electrolytic
R310203X6500-98839K Ohm, 5%, 1/4W CarbonC304203x1600-3660.068 pF, SOV Mylar
R311203X6500-7623.3K Ohm, 5%, 1!4W CarbonC308203X0412-0122.2 uF, 16V Tantal
R312203x9014-7414.7K Ohm, 5%, 1/4W Carboncw7203X1600-6340.033 uF, 50V Mylar
fats204X1450-5371K Ohm, 5%, SW CarbonC308203X0025-1743.3 uF, 50V Electrolytic
R314203X6500-481220 Ohm, 5%, 1/4W CarbonC309203X1207-1000.068 uF, 100V PP
R315203X6500-16910 Ohm, 5%, 1/4W Carbon6310203X0629-06110 uF, 100V Electrolytic
R316203X6500-7623.3K Ohm, 5%, 1/4W Carbonc3it203x0041-02510 uF, 160V Electrolytic
R317203X6700-10712 Ohm, 5%, 1/2W Carbon312202X7050-2481000 pF, 500V Ceramic
R318203X6500-540390 Ohm, 5%, 1/4W CarbonC313203X0040-05247 uF, 180V Electrolytic
R319203X6500-645,1K Ohm, 5%, 1/4W Carbon314203x 1201-2650.033 uF, 200V PP
R320203X6501-00233K Ohm, 5%, 1/4W CarbonC315,203X0629-0231 uF, 50V Electrolytic
R321203X6501-224270K Ohm, 5%, 1/2W CarbonC351203x0629-0231 uF, 50V Electrolytic
R322203X6500-88640K Ohm, 5%, 1/4W CarbonC362203X0619.045,47 uF, 25V Electrolytic
R351203X8500-88610K Ohm, 5%, 1/4W CarbonC353203X1190-0150.0082 pF, 50V Mylar-PP
F352203X6500-7853.9K Ohm, 5%, 1/4W CarbonC354203X0619-04547 UF, 25V Electrolytic
R353203X6501-08668K Ohm, 5%, 1/4W CarbonC355203X1600-3660.0068 pF, 50V Mylar
F354203x6500-7623.3K Ohm, 5%, 1/4W CarbonC356202X7050-4830.01 uF, S00V Ceramic
R355,203x9205-143,6.8K Ohm, 5%, 3W Metal Oxide0369202X8065-608100 pF, 500V Ceramic
R358203X5601-87856K Ohm, 5%, 1/2W CarbonC360202X7050-3660.0033 pF, 500V Ceramic
360203X6500-561470 Ohm, 5%, 1/4W CarbonC361202X7050-4830.01 uF, 500V Ceramic
R361203X6500-88610K Ohm, 5%, 1/4W Carbon362202X7203-0320.01 uF, 50V Ceramic
R362203x9014-6451.8K Ohm, 5%, 1W Metal OxideB*C363203X 1270-9118700 pF, 1.5 KV PP
£363204X1527-7513.9K Ohm, 5%, 7W Metal Oxide#0365203K1201-2650.33 uF, 200V PP
R364203X6500-24622 Ohm, 5%, 1/4W CarbonC366203x0019-02622 uF, 25V Electrolytic
R365,203X6501-00233K Ohm, 5%, 1/4W Carbon367202X8065-1626 pF, 500V Ceramic
isd203X6500-88610K Ohm, 5%, 1/4W CarbonC368202X7203-0320.01 uF, 50V Ceramic
R368203X5602-185330K Ohm, 5%, 1/2W Comp372203X1207-1250:1 uF. 100V PP

8-11 MAIN BOARD (CONT.)

Rel. No.P+No.Ref. No.Pari No.Description

CAPACITORS SEMICONDUCTORS (CONT)

2380202X7200.087amic208200X3181-523Transistor (NPN) 28C1815GR
Ac50I203K 1810-149.207200X3181-523Transistor (NPN) 2SC1815GR
4 0502202X7050-282Ceramic208200X3181-523Transistor (NPN) 25C1818GR
4.6503202X7810-214WV CeramicQ208200X3181-523Transistor (NPN) 2SC1851GR
Acae4202K7812.-216Ceramic210200X3181-523Transistor (NPN) 28C1851GR
505203X0075200V Electrolytic301200X3181-523Transistor (NPN) 2SC1851GR
506203Xi_0-0340302200X3207-306Transistor (NPN) 28C2073LBGL2
507203X0041.0579303200X3207-306Transistor (NPN) 25C2073LBGL2
C701293X00 19-0920351200X3248.217Transistor (NPN) 28C24828K
702203X0634-06"Q352200X4589-802Transistor (NPN) 2SD898B
703202X7080-248ae ett200X2300-0331C HA11423
a1501200X2600-183.IC 8TR381

SEMICO

apeekTRANSFORMERS & COILS
D205201X2010-158L361201X4710-134Coil, (RF Choke)
D206201X2010-1591352201X5000-083Coil, Horiz. Size
0207 .201X2010-158L701611X0004-007Coil, Adg.
208301x2010-1897351202X1300-080Transformer, Hor. Drive
209201x2010-188Ak 1352200X9720-301HV-Unit M-1t

D301 201X2010-165

302201X2010-159MISCELLANEOUS
0303201X2010-159AFSOt204x7120.073Fuse, 4 Amp. 125V
D304201X2120-008402206X5008.632Recep W Wire 3P-M-BG
D305201X2120-009P201204X9600-466Plug, PWB 3P-J
D306201X2010-159P202204X9601-477Plug, PWB 6P.
D501201X3120-216P40t204X9600-298Plug, PWB 4P-B
40502201X3120-216P50t204X8600-249Plug, PWB 2P-B
4.0503201X3120-216P601204x9600.304Plug, PWB 4P-C
4.0504201X3120-216TH501201X0100-112Thermistor

D505 201X3120-216 D: 13120:

byorZoixetgo 204FINAL ASSEMBLY PARTS
0702201X2120.009.A% 28X0128-50649VLTP22 Pix Tube
201200X3181-523Transistor (NPN) 2S61815GR205X9800-158Lateral/Purity Assembly
202200X3 181-523Transistor (NPN) 2SC1815GRA 202X1131-201Yoke Deflection
2203200X4056-260Transistor (PNP) 25A862-Y-TM204X9301-255CRT Socket
0204200X4056-260Transistor (PNP) 2SA562V-TM291X5004-262Automatic Degaussing Coil Unit
0205200%4056-260Transistor (PNP) 25A562-Y-TM

NECK BOARD RESISTORS CAPACITORS

R401203X6000-729220 Ohm, 5% 1/4W Carboncaot202x7050-2691200 pF, 500V Ceramic
R402203X6500-540390 Ohm, 5% 1/4\W Carbonc402202X7050-2481000 pF, 500V Ceramic
R403203X6000-661820 Ohm, 5% t/4W CarbonC403202X7050-2484000 pF, 500V Ceramic
Raod203X6000-729228 Ohm, 5% i/4W CarbonC404202X7050.2821500 pF, 1.5KV Ceramic
R405203x6500-54030 Ohm, 5% 1/4W CarbonC405202X7050-4830.01 uF, 500V Ceramic
R406203X6000-661820 Ohm, 3% 1/6W Carbon
R407203X6000-72¢470 Ohm, 5% #/4W Carbon
R408203X6000-998270 Ohm, 5% 14W CarbonSEMICONDUCTORS
R409203X6000-66114 Carbon401200X3206-800Transistor (NPN) 2SC2068LB
R4102039104824W MO. Forming402200X3206-800Transistor (NPN) 28C2068L8
Ratt203X9104-8242 M.O. FormingQ403200X3206-800Transistor (NPN) 2SC2068LB
R412203K9104-8245% 2W M.O. Forming
R413203X6000.9982.7K Ohm, 5%1/2W Comp.
R414203X6000-9982.7K Ohm, 8% 1/2W Comp.MISCELLANEOUS
pieaeSRtmcome401206X5009-296RECEP W Wire 4P-E
‘.2Ohm, 5% AW Metal Oxide402204X9600-254Plug,PWR 3P-A
R419203X6500-7412.7K Ohm, 5% 1/4W CarbonP403204X9600-981Pi 9. Pin1P.
R420203X6500-7412.7K Ohm, 5% 1/4W Carbon,ug,Pin 1D
bee.P701204X9601-020Plug, PWB 4P-E
R421203X6500-7412.7K Ohm, 5% 1/4W Carbon
vR401204K2115.014500 Ohm,
R402204X2115-014500 Ohm, -B Semi-Fixed
vR403204X2115-0065K Ohm, "8 Semi-Fixed
vRad4204x2115-0065K Ohm. -B Semi-Fixed
R405204x2115-0065K Ohm, -Bxed

8-12

Page 39

XI05 VIDEO AMR, 28c484c. zou XI06 VIDEO AMP. 25A673¢ MOl-xd3 RGB VIDEO OUTPUT, 28C28Il or 2ScIsiaV

'X301,%302,5308,x308 lene AMP “CSAC oF 2OCI6E5 mesa Te Hemme Be 308 cml 3 | " we ot | | ay 4 weanrive vsvwe | — {yd 5 —_X308 SEAM LIMITER 284673 Tit [9308 BLanaing 25C454C or ticles mcr prser

X901 POWER DRIVE 25¢ 2688 902 ERROR AMP —2SC1890

x04 { 28cuo6a, asciase PoweR REGULATOR sera, fee Fat, ty i ae i i tr

erPgth

ere care cur a

BAjaf |]=
xsoroteme
as 80caem
an carenOtfamSchematic Notes

ere L Unless otherwise specified fp Resistance: (Q) (K->KQ, M-M&), 1/4 (W) carbon resistor + Capacitance: 1 or higher— (pF), less than 1-~ (yF) i i working voltage -> 50 (V) ' i ceramic capacitor L ff: Inductance: (vH) Electrolytic Cap: Capacitance Value (» F)//working voltage (V), NP -* non-polar (or bipolar) electrolytic cap. Refer to the parts list for additional component information oyor DEFLECTION YOKE

2 i i tion

X7OI_ X-RAY PROTECTOR301 HORIVEor OUT2indicates test point connection
701 X-RAYPr28cls07 BO, 25ces7v 250808 or:,.iflec
SEAS Attar, ASEIGRP-Scaen of Escecue ss0803ohindicates chassis ground unless otherwise specifies

zs0820 ACIZOV 6OH2/50H: Hz __ indicates cycles per second 10% For safety purposes (and continuing reliability) a replace all componenis marked with safety syrnoo wit" identical type.

NOTE: FR — fusibie resistor

00-4147-04 Parts identification on circuit boards: G07-CBO e.g. SU1126A (R107 = R1107) SU3030A (R113 = R3113}

Page 40

REPLACEMENT PARTS LIST - ELECTROHOME 19”” MONITOR

special characteristics important to safety. Components identified by the A symbol in the PARTS LIST and on the Schematic have

DO NOT degrade the safety of the set through improper servicing.

Abbreviations for Resistors and Capacitors

Resistor Capacitor CR Carbon Resistor C Cap.

Comp. R: Composition ResistorM Cap
OMR: Oxide Metal Film ResistorE Cap.
VR: Variable ResistorBP E Cap.

MFR : Metal Film Resistor

CMF R: Coating Metal Film ResistorMM Cap.
UNF R: Nonflammable ResistorPP Cap.
FR: Fusible ResistorMPP Cap.

PS Cap Tan. Cap. Cerarnic Capacitor Mylar Capacitor Electrolytic Capacitor Bi-Polar (or Non-Polar} Electrolytic Capacitor Metalized Mylar Capacitor Polypropylene Capacitor Metalized PP Capacitor Polystyrol Capacitor Tantal Capacitor

NOTE: When ordering replacement parts please specify the part number as shown in this list including part name, and model number. Complete information will help expedite the order. Use of substitute replacement parts which do not have the same safety characteristics as specified, may create shock, fire or other hazards. For maximum reliability and performance, all parts should be replaced by those having identical specifications.

SERVICE REPLACEMENT PARTS LIST

Symbol Description Main P.C.B. Ass'y CRT Socket P.C.B. Ass'y Purity Shield Ass’y Part Number SU-1133A SU-3032A 07-220083-03 Outside of the P.C.B. Ass'y Symbol Description Picture Tube 19” A £SDeflection Yoke PC Magnet A A\Flyback Transf. A AHVR ROS UNF Resistor 2200,25W K C04 C Capacitor 150pF, AC1.5KV x01 Si. Transistor x02 Si. Transistor sc Screw #8-% sc Screw % x % Pix Tube Mtg. (4) WA Pyramidal Lock Washer (4) Nut Retainer, Pix Tube Mtg. (4) Clip — P.C.B. Support Standoff Wire Terminal (Gnd. Strap) Terminal Lug (Gnd.) Groundstrap Assy. Grounding Spring Wire Hook (Gnd. Strap) Purity Shield Holddown Clamp Support Brkt. RH Support Brkt. LH Chassis Base Yoke Wedge (3)

Purity Shield Ass’y. Parts List

Symbol Description Degaussing Coil D911, D912 Rectifier 1 Amp 600V (2) Pin Terminal (2) Pin Terminal Housing Purity Shield (2 pcs.) Purity Shield (2 pcs.) C911 Capacitor 100nF 10% 400V R921 Resistor, Wirewound 3322, 4W Fire Retardent Term. Strip 4 Lug

CRT Socket P.C.B. Ass’y (SU-3032A) Parts List

Resistors Symbol Description

R3105VvR 200
R3106vR 200
R3113vR SK
R3114vR 5K
R3115VvR 5K
R3116OMR 10KQ2W J
R3117OMR 10KQ2W J
R3118OMR 10KQ2W J

R3119 Comp. R 3.3KQ%WK R3120 Comp. R 3.3KQ*%W K C3121 Comp. R 3.3KQ2%W K

Capacitors Symbol Description C3107 E Cap. 10uF 250VA C3108 Cc Cap. 1000pF DC1400V P

Coils Symbol Description L3101 Peaking Coil Part Number 17-7198-03 A29779-D = 21-141-01 A75034-B = 29-32-01 A29951-B A46600-A QRF258K-221 QCZ0101-005 2SD870 2SC1106A 31-610818-06 31-601418-12 33-255-01 33-494-01 33-629-02 33-670-010R-02 34-228-03 34-33-04 34-574-02 35-212-03 35-3053-02 35-2348-01 35-3890-01 35-3890-02 38-449-02 39-1233-01

Part Number 21-1007-30 28-22-27 34-708-01 34-709-01 35-3847-01 35-3847-02 48-171544-62 42-113301-03 34-492-09

Part-Number QVZ3234-022 QVZ3234-022 QVZ3234-053 QVZ3234-053 QVZ3234-053 QRG029J-103 QRGO029J-103 QRG029J-103 QRZ0039-332 QRZ0039-332 QRZ0039-332

Part Number QEWS53EA-106 QCZ9001-102M

Part Number QQL043K-101

Page 41

Semiconductors Symbol X3101 X3102 X3103

Miscellaneous Symbol A Description Si. Transistor Si. Transistor Si. Transistor

Description AXCRT Socket

Main PCB Ass’y (SU-1133A) Parts List

Resistors Symbol R1406 R1408 R1410 R1414 R1415 R1421 R1422 ASFR1401 4R1503 R1504 R1509 R1512 R1514 R1515 R1522 R1523 R1528 R1534 VR1501 AR1703 ASR1704 4R1901 R1902 R1903 R1904 R1905 A.Q1908 A\R1909 R1910 AXFR1901

Capacitors Symbol C1301 1402 1407 1411 C1412 C1508 AC1512 AC1513 AC1514 C1515 C1520 C1523 C1524 AC1531 401532 C1904 1905 Description Vv R 2002 Vv R 2002 CMF R 68Q1WJ OM R 3.3KQ1W J OM R 27KQIWJ

OMR12KQ2W J

Vv R 10KQ AF R 6822W K AXCMF Rs 11.8KQ.%W +1% Vv R 5KQ

OMR10K22W J

OM R 8.2KQ2W J OM R 82022W J CMF R 8&2Q1WJ CMF R 4701WJ OM R 6822W J OM R 39021W J ZN R ZN R ACME R_ 39Q%W +1% AXCMF RE 7.68KQ KW +1% A\Posistor UNF R 2Q7WK CMF R 4.703W J

OMR10KQ2W J
OMR18KQiW J

ACMF RR 47Q.4W +1% Vv R 2KQ ACMF RR 2.74KQYW +1% AF R 2200%W K

Description BPE Cap. 3.3uF 50V A Tan. Cap. 2.2uF 16V K E Cap. 4.7uF 6.3V A E Cap. 100uF 160V A

  • Cap. 3.3uF 160V A PP Cap. 5600uF SOV J APP Cap. 2000pF DC1500V J AXPP_ Cap. 2000pF DC1500V J AXPP_ Cap. 2000pF DC1500V J PP Cap. 0.53uF DC1200V J BPE Cap. 3.3uF 50V A E Cap. 1uF 160V A M_— Cap. 0.1uF 200V K A\PP Cap. 2000pF DC1500V J AXPP_— Cap. 1500pF DC1500V J E Cap. E Cap. 10uF 250V A Part Number 28C1514VC 28C1514VC 28C1514VC

Part Number A76068

Part Number QVZ3230-002 QVZ3230-002 QRX019J-6R8 QRG019J-332 QRGO019J-272 QRG026J-123Z QVZ3230-014 QRH024K-680M QRV142F-1182 QVZ3230-053 QRG026J-103Z QRG026J-822Z QRG026J-821Z QRX019J-8R2 QRX019J-4R7 QRG026J-680Z QRGO019J-391 ERZ-C052K471 ERZ-C0S5DK271 QRV122F-3902 QRV142F-7681 A75414 QRFO76K-2RO QRX039J-4R7 QRGO026J-103Z QRGO19J-183 QRV122F-470Z QVP5A0B-023E QRV142F-2741 QRH124K-221M

Part Number QEN61HA-335Z QEES1CK-225B QEW51JA-475 QEWS52CA-107 QEWS52CA-335 QFP31HJ-562 QFZ0082-202 QFZ0082-202 QFZ0082-202 QFZ0067-534 QEN61HA-335Z QEW62CA-105Z QFM720K-104M QFZ0082-202 QFZ0082-152 QEY0034-001 QEW52EA-106

Page 42

Coils Symbol 11502 11503 L1504

Transformers Symbol 71501 T1503

Semiconductors Symbol 101501

X1101 X1102 X1103 X1104 X1105 X1106 X1301 X1302 X1303 X1304 X1305 X1401 X1402 X1501 X1901 x1902

D1101 D1102 D1103 1301 D1401 D1402 D1503 D1504 D1505 D1506 D1507 D1508 Ap1701 A\D1901 A\D1902 A\01903 A\D 71904 A\D1905

Miscellaneous Symbol A\F1901 AXF1902

Description Part Number

Linarity Coil A39835, Width Coil C30380-A, Heater Choke C30445-A

Hor. Drive Transf. A46022-BM Side Pin Transt. C39050-A

IC HA11244

Si. Transistor 2SC1685(R) Si. Transistor 2SA673(C) Si. Transistor 2SC1685(R) Si. Transistor 2SA673(C) Si. Transistor 28C1685(R) Si. Transistor 2SA673(C) Si. Transistor 2SC1685(R) Si. Transistor 2SC1685(R) Si. Transistor 2SA673(C) Si. Transistor 28C1685(R) Si. Transistor 2SC1685(R) Si. Transistor 28D478 Si. Transistor 28D478 Si. Transistor 28C2610BK Si. Transistor Si. Transistor

Si. Diode Si. Diode Si. Diode Si. Diode Si. Diode Zener Diode

Si. Diode Si. Diode Zener Diode Si. Diode Si. Diode Si. Diode AXZener Diode ASSi. Diode ASi. Diode ASi. Diode ASSi. Diode AsZener Diode

Description AFuse 1.25A AXUL Fuse 3A 2SC2688 (K.L.M.) 2SC1890A (E.F.) WO6A WO6A WO6A 1$Z473H 18Z473H RD10F(C) HF-1 VOSE RD11E(B) WO6A 18881 18Z473H RD20EV2 1$1887A 181887A 181887A 181887A RD6.8EV3

Part Number QMF53U1-1R25S QMF66U1-3ROS

Page 43

X303 BEAM UMITER 258673 ca | CRT SOCKET pce assy |

ICol POWER REGULATOR R MAIN PCB ASSY

X70) X-RAY PROTECTOR Schematic Notes Unless otherwise specified Resistance: (Q) (K->KQ, M->MQ), 1/4 (W) carbon resistor Capacitance: 1 or higher-> (pF), less than 1-> (yF) working voltage -» 50 (V) ceramic capacitor Inductance: ( H) Electrolytic Cap: Capacitance Value (yF)/working voltage (V), NP -> non-polar (or bipolar) electrolytic cap. Refer to the parts list for additional component information. 2 indicates test point connection oh indicates chassis ground unless otherwise specified Hz indicates cycles per second For safety purposes (and continuing reliability) a replace all components marked with safety symbol with identical type.

NOTE: FR - fusible resistor —e3~'

Parts identification on circuit boards: e.g. SU1126A (R107 = R1107) $U3030A (R113 = R3113)

Page 44

REPLACEMENT PARTS LIST - ELECTROHOME 13”’ MONITOR

Components identified by the A symbol in the PARTS LIST and on the Schematic have special characteristics important to safety.

DO NOT degrade the safcty of the set through improper servicing. H

Abbreviations for Resistors and Capacitors

Resistor Capacitor

CR: Carbon ResistorC Cap.Ceramic Capacitor
Comp. R: Composition ResistorM CapMylar Capaciior
OM R: Oxide Metal Film ResistorE Cap.Electrolytic Capacitor
VR: Variable ResistorBP E Cap.Bi-Polar (or Non-Polar)
MFR: Metal Film ResistorElectrolytic Capacitor
CMF R: Coating Metal Film ResistorMM Cap.Metalized Mylar Capacitor
UNF R: Nonflammable ResistorPP Cap.Polypropylene Capacitor
FR: Fusible ResistorMPP Cap.Metalized PP Capacitor

PS Cap : Polystyrol Capacitor Tan. Cap. : Tantal Capacitor

NOTE: When ordering replacement parts please specify the part number as shown in this list including part name, and model number. Complete information will help expedite the order. Use of substitute replacement parts which do not have the same safety characteristics as specified, may create shock, fire or other hazards. For maximum reliability and performance, all parts should be replaced by those having identical specifications.
SymbolDescriptionPart Number

Main P.C.B. Ass'y SU-1103A CRT Socket P.C.B. Ass'y SU-3016A

Outside of the P.C.B. Ass’y

SymbolDescriptionPart Number
Av01A\Picture Tube370ESB22(E)
ADY01A\Deflection YokeC29123-V

PC Magnet A76366-A Wedge 30006 AFlyback Transf. A19183-A

ARIIAFocus V RA46606-A
AROSUNF Resistor 2202, 25W. KQRF258K-221
Axco4AC Capacitor 150 pF, AC1.5KVQCZ0101-005
x01Si. Transistor2SD869
1C01IC RegulatorSTR383
Lo1Degausing Coil21-1007-31

Degausing Coil Pin Terminal (2) 34-708-01 Degausing Coil Pin Terminal Housing 34-709-01 Groundstrap Ass’y, 34-697-04 Groundstrap Wire Terminal 34-228-03 Groundstrap Spring (2) 35-3560-01

BRSupport Bracket RH35-3919-01
BRSupport Bracket LH35-3919-02
scSCREW 10-'% Pix Tube Mtg. (4)31-631018-08
WAPyramidal Lockwasher (4)33-255-01

Clip P.C.B. Support (2) 33-629-02 Ground Lug 34-33-04

CHChassis Base38-452-01

8-19 Main P.C.B. Ass'y (SU-1103A) Parts List

Resistors Symbol! R1406 R1408 R1410 R1414 R1415 R1421 R1422 AXFR1401 A\R1503 R1504 R1509 R1511 R1514 R1515, R1522 R1523 R1528 R1534 VR1501 ASR1703 AXR1704 AR1901 R1902 R1903 R1904 ASFR1901

Capacitors Symbol 1402 1411 C1412 C1508 C1511 ACI512. AC1513 Ac1514 C1515 C1520 C1524 1904 C1905 A\C1907

Coils Symbol L1501 1502 L1503 1504 L1901

Transtormers Symbol T1501 T1503 CMF R 6891WJ R 3.3KQ1W J R 27KQWJ OM R 12KQ2WJ R 10KQ R 68Q2W K ASCMF Ro 11.8KQ«W +1% VR 5KQ OM R 10KQ2W J OM R 5.6KQ2W J OM R 68022W J CMFR 82Q1WJ CMF R 4.7Q1W J OM R 5622WJ OM R 39021WJ ZN R ZN R ACMF R_ 39K QW +1% ACMF R_7.68KQYUW +1% A’Posistor UNF R 2Q7W K CMF R 5.623W J OM R 10KQ2W J AF — R 22024%WK

Description Tan.Cap. 2.2uF 16V K

  • Cap. 100uF 160V A E Cap. 3.3uF 160V A PP Cap. 5600pF 50V J E Cap. 47uF 160V A A\PP Cap. 2000pF DC1500V J AXPP Cap. 2000pF DC1500V J APP Cap. 2500pF DC1500V J PP Cap. 0.53uF DC1200V K BPE Cap. 1uF 50V A M Cap. 0.1uF 200V K E Cap. E Cap. 10uF 250V A A\MM Cap. 0.1uF AC150V Z

Description Peaking Coil Liniarty Coil Width Coil Heater Choke Line Filter

Description Hor. Drive Transf. Side Pin Transf.

8-20 Part Number QVZ3230-022 QVZ3230-022 QRX019J-6R8 QRGO019J-332 QRG019J-272 QRG029J-123 QVZ3224-014H QRH024K-680M QRV142F-1182 QVZ3230-053 QRG029J-103 QRG029J-562 QRG029J-681 QRX019J-8R2 QRX019J-4R7 ORGO29J-560 ORG019J-391 ERZ-C05ZK471 ERZ-COS5DK271 QRV122F-3902 QRV142F-7681 A75414 QRFO76K-2RO QRX039J-5R6 QRG026J-103Z QRH124K-221M

Part Number

QEES1CK-225B QEWS2CA-107 QEW52CA-335 QFP31HJ-562 QEWS52CA-476S QFZ0082-202 QFZ0082-202 QFZ0082-252 QFZ0067-534 QEN61HA-105Z QFM72DK-682M QEY0034-001 QEWS52EA-106 QFZ9008-104

Part Number A75360-6 A39934 C30380-A C30333-A A39475-J

Part Number A46022-BM C39050-A

Page 45

Semiconductors Symbol 101501

x1101 x1102 X1103 X1104 X1105 X1406 X1301 X1302 X1303 x1304 X1305 x1401 x1402 X1501 x1701 D1101 D102 D1103 D1301 1401 01402 D1503 D1504 D1505 01506 01507 D1508 401701 AxD1901 A\p1902 A\D1903 AxD 1904

Miscellaneous Symbol ASF1901 AF1902 Description Lc.

Si. Si. Si. Si. Si. Si. Si. |. Transistor Si. Si. Si.

Si Transistor Transistor Transistor Transistor Transistor Transistor Transistor

Transistor Transistor Transistor

Si. Si. Si. Si. Si. Si. Transistor Diode Diode Diode Diode Diode Zener Diode Si. Si. Diode Diode Zener Diode Si. Si. Si. Diode Diode Diode AsZener Diode ASi. ASi. ASI. ASi. Diode Diode Diode Diode

Description AFuse 1A ANUL Fuse 3A Part Number HA11244

2SC1685(R) 2SA673(C) 2SC1685(R) 2SA673(C) 2SC1685(R) 2SA673(C) 2S01685(R) 2SC1685(R) 2S8A673(C) 2SC1685(R) 2SC1685(R) 2SD478 2SD478 2SC2610BK 2SC1685(P-S) WO6A WO6A WO6A 182473H 182473H RD10F(C) HF-1 Voge RD11E(B) WO6A 18881 182473H RD20EV2 1S1887A 1$1887A 181887A 1$1887A

Part Number QMFS3U1-1ROS QMF66U1-3R0S

Page 46

CRT Socket P.C.B. Ass'y (SU-3016A) Parts List

Resistors Symboi R3105 R3106 R3113 R3114 R3115 R3116 R3117 R3118 R3119 R3120 R3121

Capacitors Symbol C3107 C3108

Colls Symbol £3101

Semiconductors Symbol X3101 X3102 X3103

Miscellaneous Symbol A Description Vv R 2002 v R 2002 Vv R 5KQ v R 5KQ v R 5KQ OM R 10KQ2W Ss OM R 10K22W J OM R 10K22W J Comp. R 3.3KQ2%W K Comp. R 3.3KQ%WK Comp. R 3.3K Q%W K

Description E Cap. 10uF 250V A C Cap. 1000pF DC1400V P

Description Peaking coil

Description Si. Transistor Si. Transistor Si. Transistor

Description A\CRT Socket

8-22 Part Number QVZ3234-022 QVZ3234-022 QVZ3234-053 QVZ3234-053 QVZ3234-053 QRG029J-103 QRG029J-103 QRG029J-103 QRZ0039-332 QRZ0039-332 QRZ0039-332

Part Number QEWS2EA-106 QCZ9001-102M

Part Number QQL043K-101

Part Number 2802611 28C2611 28C2611

Part Number AT5522

Page 47

IX Schematics and Wiring Diagrams |

Page 48

4 1k s i mt

ae = oon

  • at = aoe L| 7 = ra

LE 1st coms

Ta Shas ete ed MT. 1958 _ om m1 44 im vey 4 na sen se 1d ie i m4 ma na mt mt mt a snap sip-no® we Lyt oles ms i

os is Let

tos

f f we ee SE eee ye ee ee eee ee eee be oe ee ee ce ee ee ne 4

:POWER CHASSIS *70VA - UPRIGHTBALLY / MIDWAY
1-5 rena BARRIER STR OLMISMSV ~ GORE10601 W BELMONT AVE.
aPART NO. A945- 00036-0002FRANKLIN" PARC IL 6013!

7 OWG. NO. MOS! - 00945 -BO5I_ INGREAGED FUSE VALUES] WO Was SaMP “now aaup™ | 315-63 Was AMP — Now SAMP ADDED PART NO. (U.L.) FEV | INCREASED Flise VALUE WAS. Sane “NOW ‘SAME

Page 49

ar aa

Se fee Lit " 2 baw so-80

TWOREASED FUSE VALUES WAS 3AMP = NOW 4AMP WAS 4aMP — NOW SAMP ADDED _PART_NO._(U.L.) INCREASED FUSE “VALUE WAS. 3AMP = NOW AMP PART NO. A845 -00036-0000 DWG NO. “MO5I-00945-B046 POWER CHASSIS *70VA BALLY, / MIDWAY coc! 060! iu Narceme MODEL Frat Paes 6D

Page 50

FF

i : we

REV. @] NGREASED FUSE VALUES | WB WAS SAMP'- NOW 4AMP- | 3-15-63, ADDED PART NO. (UL) REV. ©) | INCREASED FUSE VALUE | MB WAS 3AMP— Now aame | 3-24-83

POWER CHASSIS "125 VA

SV, = GOH, PART NO, A945 - 5 A945 - 00020-0000 DWG. NO. MOSI - 00945 -BO37 BALLY / M IDWAY. I 10601 W. BELMONT AVE. FRANKLIN PARK, IL. 60131

Page 51

TO YOKE 10_YOKE

t _7s2Asa__

| rea 6 a!

|vert. toveerwiz. _f'33 |
TWIST CABLEa“} —rea——
msi)|
Yo|Ww
=iioe|
Ss vem 4 ytvent|}Loo
veRT.vio|SU)LegeRIVER
|.=a
{363a|we5
ig}eremaandenere brazsah nessas desaee J |
||eeulee TSfom TaSal

C3222 | 77

* ° = 4.¢3216 | os209 eto mas) ever Pe oie

|Qx3202CR32055300"

| 2eky

  • |< fs,
R206,ut||VOLTAGE

RK: |

ox3207coconsPE | wane

121-975} ball SHUTDOWN |.csoa3 =

—_=63v

3201 3 ve a

be

-_srov (e-P

o

:|aa
52_|_ammperr_19-186-03
om |Sys
Let—-:_

Sih Rwrse Sheree. ara Pie i i j | [3 ono

oo —+ ae 9-\g6-03

craaut

oxi] 03208 ny

F 4 I ree |

—i 2240 7 1

A-9740-05 +

cLosae

REFERENCE ONLY

SCHEMATIC FOR 9- 186-G2 SWEEP BOARD RGB COLOR MONITOR ZENITH | '* RADIO corP..! B CHICAQO, ILL. 3-186

"M051-00087-A021

ores sg wie crncut REFERENCE oestousroRs? Bue ssce MunTS LigY FON aePLicaBL= Usaee See | LER mise useD tS © -@* © PROVISION ON PRITITEE CIRCUIT BOARO,

Page 52

9-155-10 | (204-960) |

i !

RS110 t 1K ) €5103 Hl €5102/ J 7 |

A i f } 7 |

| RELLY iL S104 L5103 | eo ‘220UH 3220UH

R513 ¢RS112 Q5103, 4.7K 47K ! L510) | ae 3H + +

95102 + 121-1034 | | RED OUT ! i 1 esto pmes t = RS11S 180 | 1/4W |

| RS114 no 14a I

i

«156 CENTERS

T Lae L +140 VOC

‘ACL RESISTORS ARE 1/2WATT UNLESS OTHERWISE. SPECIFIED. M05 1-00087-A022

SCHEMATIC FOR NOTES: (USED WITH CIRCUIT REFERENCE DESIGNATORS) A. P/L = SEE PARTS LIST FOR APPLICASLE USACE. — > wih B. ee = JUMPER WIRE USED INSTEAD. ROE OR MONITOR C. em © = PROVISION ON PRINTED CIRCUIT BOARD. CRT_SUCKET SOAK th + ZENITH | owen SRO RADIO CORP. Ps CHICAGD, ILL. se

Page 53

-—TO H.0.T. ASSY

A-lO0530

c3 c4 530 PF 7 530 PF

18-3059

73-3059 |

a 1 c2 Le PE tt

NOTE: M051-00087-A023 WIRE HOLES #22 GA. SCHEMATIC FOR A-10539 70 WIDTH STEF ASSY

SWEEP MODULE RADIO CORP. A-|0530

CHICAGO, ILL.

Page 54

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 55

MAIN MODULE (SEE CHART) 7 363 ek aly oooo0 fia] a

—3W3|-

a oso o/b 303 -

idpoao00fs}°oo

2A3 | Q1\c i DAG

9||wy

| SWEEP MODULE (SEE CHART)

E x

ooo0000 poo 3s3 3R3

ao ooo

L ! o? 5 | 2A 285 3F3 318 3s8 3R8 20] [a

i fp J HV POWER

ASSEMBLY

—, YOKE (SEE CHART:

  • MIO + AIR : | TO DEGAUSSER So

AC

VIDEO OUT (SEE CHART)

[a |sxa a

3h 383 4

Pa PCB

WIDTH STEP (SEE CHART)

INTERCUNNE CJ

VIDEO GAME

ZENITH |

IMPORTANT CAFETY NUTICE WHEN SERVICING THIS CHASEIE, UNDER NC CIRCUMSTANZS "SHUULO THE ORIGINAL UE-

SIGN BE MCCIFIEL OR ALTEREL WITHOUT

PERMISSICN FRUM THE ZENITH RACIC COR- PORATICH. ALL COMPONENTS SHOUL PLACEL CNLY WITH TYPES IGENT THOSE IN THE ORIGINAL THEIR PHYSICAL LOCATE ING AND LEAL oR T“GNFORM TC ORISINAL CAYGUT CMPCETION OF REFATRS. FON FepectaL <IRCUITS ARE ALSO USEL_TO RE- 1 VENT SHCEK ANC FIRE HAZARD. THESE AREAS | ARE SHAGEL ON THE SCHEMATIC FOR EASY ICENTIFICATICN, THE LETTER * cl ' IN THE [TEM NUMBER LES IGNATE: AFE COMPONENTS IN THESE AREA: ; ARE REGUIREL TL MRINTALY | FORMANCE. NO LEVIATIUNS ARE AL. | WITHCUT PRIOR APPROVAL St. THE PRU ING LEFARTMENT ,

WIS CIRCUIT CTAGRAN GARY C CIFFER FROM THE ACTJK. CIRCUIT ISEC THIS HAY. [MFEMESTATIN OF THE CATEST SAFETY AO FERFURMAYICE IMPROVEMENT CHANGES INTC THE SET If NUT Gk AYEC ONTI. THE NEW SERVICE LITERATE 1S PRINTEL.

FOR

MONITOR