CATHODE RAY TOMES

Food Fight TM-229 3rd Printing

Food Fight (rev 3) (General Computer Corporation (Atari license), 1982) · Technical Manual · 72 pages · 55 sections · original scan

Page 1

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 2

If reading through this manual does not lead to solving a certain maintenance problem, call TELEHELP® at the Atari Customer Service office in your geographical area, as shown below.

WEST and CENTRAL U.S.A. Parts and Service

Atari, Inc. California Customer Service Office 1105 N. Fair Oaks Avenue P. O. Box 427, Sunnyvale, CA 94086 Telex 17-1103 (Monday-Friday, 7:30-4:00 pm Pacific Time) From California, Alaska, or Hawaii @ (408) 745-2900 ee Service from anywhere in the area shown in white toll-free (800) 538-1611

EAST U.S.A. Service only

Atari, Inc. New Jersey Customer Service Office 12A World’s Fair Drive, Somerset, NJ 08873 Telex 37-9347 (Monday-Friday, 7:30-4:00 pm Eastern time) exe From New Jersey (201) 469-5993 exe From anywhere else in this area toll-free (800) 526-3849

EUROPE Parts and Service

Atari Ireland Limited European Customer Service Office Tipperary Town, Ireland Telex 28-165 TIPPERARY TOWN, (Monday-Friday, 9:00-6:00 pm GMT) IRELAND

BS 062-52155

Page 3

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 4

Food Fight

© 1983 by Atari, Inc. All rights reserved. No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher. The game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the U.S. Copyright Act of 1976. This Act provides for increased penalties for violating federal copyright laws. Courts can impound infringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles. In addition, the Act provides for payment of statutory damages of up to $50,000 in certain cases. Infringers may also have to pay costs and attorneys’ fees, fines up to $25,000, and face an imprisonment of up to one year. Atari will aggressively enforce its copyrights against any infringers. We will use all legal means to immediately halt any manufacture, distribution, or operation of a copy of video games made by us. Anyone who purchases such copies risks forfeiting such a game.

Published by: ATARI, INC. 790 Sycamore Drive P.O. Box 906 Milpitas, California 95035

Printed in the U.S.A 4M

Page 5

Notice Regarding Non-ATARI Parts

‘ARNING Use of non-ATARI parts or modifications of your ATARI game Circuitry may adversely affect the safety of your game, and injure you or your players.

You may void the game warranty (printed on the inside ba you do any of the following: ck cover of this manual) if

  • substitute non-ATARI parts in the game
  • modify or alter any circuits in the game by using kits or parts vot supplied by Atari.
Note

This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart] of Part 15 of Federal Communications Commission (FCC) Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment ina residential area or modification to this equipment is likely to cause interference in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference. If you suspect interference from an ATARI® game at your location, check the following: ¢ All green ground wires in the game are properly connected as shown in the game wiring, diagram.

¢ = The power cord is properly plugged into a grounded three-wire outlet

¢ The game printed-circuit board(s) (PCB) is properly installed within the Electromagnetic Interference (EMI) cage. «The EMI Shield PCB is properly installed and connected in series with the game PCB harness.

  • All filter capacitors required on the EMI Shield PCB are properly soldered in place. If you are still unable to solve the interference problem, please contact ATARI Customer Service. See the inside front cover of this manual for service in your area,
Page 6

Food Fight

Table of Contents

1 Set-Up Procedures How to Use This Manual Game Overview. ....... Installation Specifications InspectingtheGame .......... Voltage-Plug Selection and Fuses . Switch Locations ..... .

  • Power On/Off Switch .
  • Utility Panel Switches . 7moOOR>
  • Option Switches... 2.0.0... eee beeen eee G. Selecting the Coinand Credit Options. ..............--

2 Self-Test Procedure

A. Self-Test Display. . B. Self-Test Menu . Settee eee : C. Selectingthe Options... 2.2... 000.0. 0e eee eee

3 Illustrated Parts Lists

Parts lists beginonpage ...........- OM se MAR es me

Appendix A Gimbal Joystick Maintenance ............0..0...2.. 1-4 1-4

1-6 1-6 1-6 1-6 1-6

2-2 2-3 2-6

3-2

Page 7

Figure 1-1 Figure 1-2 Figure 1-3 Figure 1-4 Figure 2-1 Figure 2-2 Figure 2-3 Figure 2-4 Figure 2-5 Figure 2-6 Figure 2-7 Figure 3-1 Figure 3-2 Figure 3-3 Figure 3-4 Figure 3-5 Figure 3-6 Figure 3-7 Figure 3-8 Figure 3-9 Figure 3-10 Figure 3-11 Figure 3-12

Figure 3-13 Figure 3-14 Figure 3-15 Figure 3-16 Figure A-1

Table 1-1 Table 1-2 Table 2-1 Table 2-2 Table 2-3 Table 2-4 Table 2-5 List of Illustrations

Game Overview, US-BuiltGame .... 1-2 Game Overview, Ireland-Built Game . 1-3 Voltage-Selection Plug and Fuse Locations 15 Option Switch Locations 1-6 Main Self-Test Menu 2-3 Hardware Tests Menu 23 Switch Test Display. 2-4 ColorPattern .... 2-4 Convergence Pattern . 2-4 Statistics Display. . . 2-5 Options Display. . . 2-6 Cabinet-Mounted Assemblies, US-Built Game 3-2 Cabinet-Mounted Assemblies, Ireland-Built Game 3-4 Control Panel Assembly. ........ 3-6 Gimbal Joystick Assembly. em 3-8 Fluorescent Tube and Speaker, US-Buil Game ee 3-10 Fluorescent Tube and Attraction Panel, Ireland-Bi Video Display, US-BuiltGame ..... . Video Display, Ireland-Built Game . Utility Panel Assembly. ......... Vertically Mounted Coin Door. « American-Made Coin Door. ........ Electromagnetic Interference emp Cage Assembly and PCB Mounting Hardware ..... . EMI Shield PCB Assembly. ...... . Food FightGame PCB .......... : Regulator/Audio I] PCB Assembly... .... Color Raster-Scan Power Supply Assembly. . Disassembling the Pivot Shaft Assembly

List of Tables

Installation Specifications 1-4 Switch Settings for Price and Bonus Options . 1-7 Playfield RAM Locations 2-2 Program RAM Locations 2-2 Program ROM Locations . . 2-2 Sound Chip Locations . 2-4 Option Settings ...... 2-6 Food Fight

Page 8

Food Fight

vi

Safety Summary

The following safety precautions apply to all game operators and service personnel Specific warnings and cautions will be found throughout this manual where they apply.

WARNINGS

Properly Ground the Game. Players may receive an electrical shock if this game is not properly grounded! To avoid electrical shock, do not plug in the game until it has been inspected and properly grounded. This game should only be plugged into a grounded 3-wire outlet. If you have only a 2-wire outlet, we recommend you hire a licensed electrician to install a grounded outlet. Players may receive an electrical shock if the control panel, video display, EMI cage, fluorescent light assembly, and utility panel are not properly grounded! After servicing, check that the green ground wire or grounding clip for each assembly is firmly attached. Only then should you lock up the game AC Power Connection. Before connecting the game to the AC power source, verify that the proper voltage-selection plug is installed on the game’s power supply Disconnect Power During Repairs. To avoid electrical shock, disconnect the game from the AC power source before removing or repairing any part of the game. Discharge High Voltage from the Video Display. When removing or repairing the video display, extra precautions must be taken to avoid electical shock. High voltages may exist within the display circuitry and cathode-ray tube (CRT) even after power has been disconnected. Do not touch internal parts of the display with your hands or with metal objects held in your hands! Always discharge the high voltage from the CRT before servicing this area of the game. To discharge the CRT: Attach one end of a large, well-insulated, 18-gauge jumper wire to ground. Momentarily touch the free end of the grounded jumper to the anode by sliding it under the anode cap. Wait two minutes and discharge the anode again. Use Only ATARI Parts. To maintain the safety integrity of your ATARI game, use only ATARI authorized parts when repairing the game. Use of non-ATARI parts or modifications of the game circuitry may adversely affect the safety of your game, void the warranty, and injure you or your players. Handle Fluorescent Tube and CRT With Care. If you drop a fluorescent tube or CRT and it breaks, it will implode! Shattered glass can fly six feet or more from the implosion. Use the Proper Fuses. To avoid electrical shock, only use replacement fuses that are specified in the parts list for this game. Replacement fuses must match those replaced in fuse type, voltage rating, and current rating. In addition, the fuse cover must be in place during game operation.

CAUTION

Properly Attach All Connectors. Before turning on the game for the first time, make sure that all connectors are properly attached. Make sure that the connectors on each PCB are properly plugged in. Note that they are keyed to fit only one way. If they do not slip on easily, do not force them. A reversed connector may damage your game and void the warranty.

Page 9

Set-Up Procedures

How to Use This Manual

This manual, written for game operators and service

technicians, describes the Food Fight™ game. The manual

contains information about both the Ireland- and US-built games. Whenever information is unique to the Ireland-

built game, this symbol appears: ®

Whenever information is unique to the US-built game, this symbol appears:

Chapter 1 contains game specifications, inspection procedures, voltage plug and fuse information, switch locations, and option information. Chapter 2 contains self-test procedures. Chapter 3 contains illustrated parts lists. Figures 3-1 and 3-2 illustrate the US-built and the Ireland-built game cabinet. Italicized type on these figures refer you to other places in the manual for information about specific cabinet parts.

Schematic diagrams of the game circuitry are included asa

supplement to this manual.

Chapter 1

Page 10

Set-Lip Procedures Food Fight

Fluorescent Tube & Speaker See Figure 3-5

Game Identification Label x

Video Display x See Figure 3-7 «Panel

Controt Panel See Figure 3-3 Gimbal Joystick See Figure 3-4 EMI Cage Self-Test Switch See Figure 3-12 Utility Panel Game PCB & See Figure 3-9 See Figure 3-14

EMI Shield PCB Coin Door Assy. . See Figure 3-13 See Figures 3-10 & 3-11 Regulator! Audio I! PCB x See Figure 3-15

WARNING Shock Hazard Deru Do not plug In the game until it has been inspected. This game should only be connected to a grounded 3wire outlet. If you Power On/Off Switch have only a 2-wire outlet, we recommend you hire a licensed electrician to install a grounded outlet. Players may receive an electrical shock If this game Is not properly grounded! x Item with a serial number label

Figure 1-1 Game Overview—US-Built Game

Page 11

Food Fight Set-Up Procedures

Fluorescent Tube & Attraction Panel See Figure 3-6 * Game Identification Label

Video Display. See Figure 3-8

Access Panel

Control Panel See Figure 33 Gimbal Joystick See Figure 34 ‘See Figure 3-14 Self-Test Switch

Coin Door See Figures 3-10 & 3-11 ige Regulator! Audio I! PCB See Figure 3-15

Utility Panel See Figure 3-9

WARNING Shock Hazard Do not plug in the game until it has been Inspected. This game should only be connected to a grounded wire outlet. If you have only a 2-wire outlet, we recommend you hire a licensed electrician to install a grounded outlet. Players may receive an electrical shock if this game is not properly grounded! Power Supply See Figure 3-16

Power On/Off Switch

Fegure 1-2 Game Overview—Ireland-Built Game

Page 12

Set-Up Procedures

B. Game Overview D. Inspecting the Game

Food Fight hero, Charley Chuck, gets points by eating his Please inspect your game carefully to ensure that it was ice cream cone before it melts. To do this, he must fight off delivered to you in good condition. Oscar, Angelo, Jacques, and Zorba, the four chefs who rise from holes and throw food at him. When Chuck eats the

cone, the ice-cream flavor changes and the game difficulty WARNING increases. Shock Hazard

To avoid electrical shock, do not plug in the All major parts of the US-built Food Fight game are illus- arn vintl the procedures in Sections D and E trated in Figure 1-1. All major parts of the Ireland-built have been completed! game are illustrated in Figure 1-2. Do not touch internal parts of the display with your hands or with metal objects held in your hands!

Cc. Installation \. Examine the exterior of the game cabinet for dents, Specifications chips, or broken parts.

  • Remove the screws from the rear access panel. Table 1-1 describes the physical, electrical, and environ- Unlock and open this panel and the coin door; inspect mental specifications of the game. the interior of the game as follows: : a. Ensure that all plug-in connectors (on the game Table 1-1 Installation Specifications harnesses) are firmly plugged in. Replug any con-
  • nectors found unplugged. Do not force connec-
Power Consumption200 Wtors together. The connectors are keyed so they
Tt7Aonly fit in the proper orientation. A reversed edge

emperature Oto +58" C (+5210 +100" F) connector may damage a PCB and will void

HumidityNot to exceed 95% relativeyour warranty.
Line Voltage100 to 240 VACb.Ensure that all plug-in integrated circuits on the

US-Built Cabinet PCB are firmly plugged into their sockets.

Width62.5 cm (25.5 in.)c.Remove the tie-wrap that secures the coiled

power cord inside the cabinet. Inspect the power

Depth 86 cm (34 in.) cord for any cuts or dents in the insulation. Repair

Height181.5 cm (72 in.)or replace it as required. Place the square strain-

Treland-Built Cabinet relief plate in the wood slot at the bottom of the

Height 181.5 cm (72 in.) or replace it as required. Place the square strain Width 60 cm (24 in.) r rear panel “ree ,

; . Inspect major subassemblies, such as the power

Depth68 cm (27 in.)supply, control panel, video display, and EMI
Height170 cm (67 in.)cage. Make sure they are mounted securely and

that the green ground wires are connected.

Page 13

Food Fight

E. Voltage-Plug Selection

and Fuses

The power supply in your game contains six fuses. When you replace a fuse, use the identical type fuse with the same electrical rating (see Figure 1-3). This power supply operates on the line voltage of many countries. The power supply comes with either one, two, or three voltage-selection plugs. Plug voltages and wire

Voltage-Selection Plug

(4 A, 250 V)

(20 A, 32 V) FUSES F4-F6' (4 A, 250 V) Set-Up Procedures

colors are 100 VAC (violet wire color), 120 VAC (yellow wire color), 220 VAC (blue wire color), and 240 VAC (brown wire color). See Figure 1-3 for placement of the voltage-selection plug. Before plugging in your game, check your line voltage. Next, check the wire color on the voltage-selection plug. Make sure the voltage-selection plug is correct for the voltage of your location. Now plug the game into a grounded 3-wire outlet.

FUSE F1 (7A, 250\) Bod FUSE F1 (4A, 250)

Figure 1-3 Voltage-Selection Plug and Fuses

Page 14

Set-Up Procedures

F. Switch Locations

Power On/Off Switch The power on/off switch is located on the back of the cabinet on the lower left side (see Figure 1-1 or 1-2).

Utility Panel Switches

The volume control, coin counter(s), self-test switch, and auxiliary coin switch are on the utility panel. The utility panel is located inside the upper coin door (see Figure 1-1 or 1-2). The volume control adjusts the level of sound produced by the game. The coin counter(s) records the number of coins entered into the game. The self-test switch initiates the self-test operating mode. The auxiliary coin switch is used to credit the game without activating a coin counter.

Option Switches

Option switches for game price selection are on the game printed-circuit board (PCB) at location SW1 (see Figure 1-4),

G. Selecting the Coin and Credit Options

Settings of the game coin and credit option switches are explained in Table 1-2. Options preset at the factory are shown by the «4 symbols. However, you may change the settings according to your individual needs.

Game PCB Food Fight

To verify other option selections, check the self-test display that appears when you turn on the game. Then, verify the option switch settings on the self-test display as described in Chapter 2, Checking Option Settings. Table 1-2 describes the settings for the DIP switch at location SW1. This switch selects the game coin and credit options available for the left and right coin mechanisms. The basic unit of measurement is a coin worth $.25 or 1 DM. Thus, if you have a 2 DM/1 DM coin door with two coin counters, set switch 5 at location SW1 to on. Then, different denominations are counted on the two coin counters.

NOTE Coin Option Interconnect Assembly JS5A-P55A (A039655-01) permits a coin placed in either coin mechanism to register in the same coin counter. The cable connector is located between the coin door harness and the main harness (see the Coin Option Interconnect Wiring Diagram in SP-229). When it is used, left coin mechanism option switches at SW1 apply to both coin mechanisms. If you want different options for the left and right coin mechanisms, remove Coin Option Interconnect Assembly J55A-P55A and connect J55 directly to P55.

Figure 1-4 Option Switch Location

1-6

Page 15

Food Fight Set-Up Procedures

Table 1-2 Switch Settings for Coin and Credit Options

Settings of 8-Toggle Switch on Game PCB (at SW1) 2 3 4 5 Option

Off Off Off On

On On

On Off

On Off

On On

Off On Off On Off On Off On

Off On Off Off On On Off Off

On On Off Off Off Off On On

On On Free Play 1 coin 2 credits 1 coin 1 credit <4 2 coins 1 credit

Right Coin Mechanism 1 coin 1 credit <@ 1 coin 4 credits 1 coin 5 credits 1 coin 6 credits

Left Coin Mechanism 1 coin 1 credit <4 1 coin 2 credits No bonus coins < No bonus coins For every 4 coins, logic adds 1 more coin For every 2 coins, logic adds 1 more coin For every 5 coins, logic adds 1 more coin For every 3 coins, logic adds 1 more coin

No bonus coins No bonus coins

4 Manufacturer's recommended settings

Page 16

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 17

Self-Test Procedure

This game will test itself and provide data to show that the game circuitry and controls are operating properly. Selftest data is presented visually on the player LEDs and the video display, and audibly through the speakers. No additional equipment is required. We suggest that you perform a self-test when you first set up, each time you collect money, change the game options, or suspect game failure.

Chapter 2

Page 18

Self-Test Procedures

A. Self-Test Display

When the power switch is turned on, Food Fight enters the automatic selftest mode, which tests playfield RAM, program ROM, and non-volatile RAM (NVRAM). At the beginning of these tests, both the one-player and two-player LEDs are [it. (This is so that the success or failure of the tests can be indicated even if the messages cannot be displayed on the monitor.) If the playfield RAM and program RAM are working, then the one-player LED turns off and the message RAM OK is displayed on the screen. If the playfield RAM fails, the one-player LED flashes one through four times followed by a pause. The playfield RAM number displayed corresponds to the board location of the faulty chip as shown in Table 2-1.

Table 2-1 Playfield RAM Locations

Playfield RAM

Number Board Location

1 3K 2 3L 3 3M 4 3N

If the program RAM fails, the one-player LED remains on, and the number of the bad chip is displayed. The program RAM number corfesponds to the board location of the faulty chip as shown in Table 2-2.

Table 2-2 Program RAM Locations

Program RAM

0 8B 1 8A 2 9B 3 9A

After the RAM is checked, the checksums for program ROM are verified. If all ROMs check out correctly, then the two-player LED is turned off and the message ROM OK is displayed. If there are faulty chips, then the ROM number

2-2 Food Fight

of each faulty chip is displayed, The ROM number cor-

responds to the board location of the faulty chip as shown,

in Table 2-3.

Table 2-3 Program ROM Locations

ROM Number Board Location

9C 8C 9D 8D OF 8E OF SF MON Rw Ne

After the program ROM is checked, the checksums for the NVRAM are verified. If all sections of the NVRAM check, then the message NVRAM OK is displayed. If any section of NVRAM fails, then the name of the faulty section is displayed and factory values from program ROM are used instead of the values from that section. If playfield RAM, program RAM, and NVRAM check out correctly, Food Fight goes into the attract mode after five seconds. If NVRAM fails, the game will go into the attract mode when the THROW button has been pushed. The five sections of NVRAM are as follows: STATISTICS holds the values for the statistics display (see the description under Self-Test Menu). These values can be reset using the options menu TIME AND CREDITS holds the total time the machine has been on, and the total number of credits. These appear at the bottom of the statistics display and cannot be reset. HIGH SCORES holds the player initials, scores, and levels achieved for the top three high-scoring games. These values appear at the top of the high-score table during the attract mode and can be reset using the options menu OPTIONS holds the current settings for the game options, which can be displayed and/or changed using the options menu. JOYSTICK VALUES holds the maximum and minimum values for the analog joystick. See the description of Joystick Calibration under the TESTS option of the selftest menu.

Page 19

Food Fight

B. Self-Test Menu

Food Fight has a menu-driven self-test mode which is entered by turning the self-test switch on. Turning the self-

test switch off at any time during self-test mode causes the

game to return to the attract mode. Immediately after the self-test switch is turned on, the main self-test menu appears as shown in Figure 2-1. Three choices are available—TESTS, STATISTICS, and OP- TIONS. Move the joystick up or down to change the current selection, which is displayed in red. Push the THROW button to select.

SELF-TEST

MOVE JOYSTICK TO CHANGE PUSH THROW TO SELECT

TEsTs STATISTICS OPTIONS

TURN SELF-TEST SWITCH OFF TO ENO

Figure 2-1 Main Self-Test Menu

NOTE The two-player start button can be used to cycle through the selections in any of the self-test menus so the game can be tested even if the joystick is faulty.

Hardware Tests

Selecting TESTS causes the hardware test menu to appear as shown in Figure 2-2. There are five choices available— JOYSTICK CALIBRATION, SWITCH TEST, COLOR PATTERN, CONVERGENCE PATTERN, and SOUND TEST. Use the joystick and THROW button to select any option. Push the one-player start button to return to the main self-test menu. Self-Test Procedures

TESTS PusH START 1 TO ENO TESTS

JOYSTICK CALIBRATION SWITCH TEST COLOR PATTERN CONVERGENCE PATTERN SOUND TEST

Figure 2-2 Hardware Tests Menu

JOYSTICK CALIBRATION resets the joystick minimum and maximum values, and should be used whenever the NVRAM or joystick is replaced. Hold the joystick steady for a full five seconds in each direction (left, right, up, down) to store new values. Push the oneplayer start button to return to the TESTS menu.

NOTE Food Fight is equipped with a self-calibrating joystick, which checks its maximum and minimum values while the game is being played. Initial values are set at the factory and stored in NVRAM. When Food Fight is turned off, the NVRAM values are updated. Each time Food Fight is turned on, the current values are read out of NVRAM. If NVRAM fails (see the description under Automatic Self-Test), then the joystick is recalibrated as the game is being played. In this case, the control will be sluggish for the first game or two after the game is turned on.
Page 20

Self-Test Procedures

SWITCH TEST displays the state of the control panel switches, the joystick values, the coin inputs, and the dual-inline-package (DIP) switches as shown in Figure 2-3. Aone (1) indicates that the switch is on, anda zero (0) indicates it is off. All eight bits are displayed for each direction of the joystick. Push both the one- and two-player start buttons to end this test. See Chapter 1, Selecting the Options, for information on the settings of the DIP switch located on the game PCB.

Figure 2-3 Switch Test Display

COLOR PATTERN displays all 256 Food Fight colors ona 16-by-16 grid of blocks in the center of the screen as shown in Figure 2-4. Use this display to check for color adjustment. Press the one-player start button to end this test. The colors are properly adjusted when the background is black and each colored block is distinguishable from those around it. Food Fight has four blue levels, eight green levels, and eight red levels. These are overlayed to display the color grid as follows: ¢ Blue is displayed in four quadrants with level 0 (no blue) in the lower left quadrant, level 1 in the lower right quadrant, level 2 in the upper left quadrant, and level 3 (intense blue) in the upper right quadrant.

© — Greenis displayed in sixteen horizontal bars, two bars

for each level, with level 0 (no green) bars at the center, level 7 (intense green) bars across the top and bottom, and intermediate levels in between. ¢ Red is displayed in sixteen vertical bars, with level 0 (no red) bars at the center, level 7 (intense red) bars at the right and left, and intermediate levels in between.

2-4 Food Fight

Figure 2-4 Color Pattern

CONVERGENCE PATTERN a white crosshatch pattern appears on the screen as shown in Figure 2-5. Use this pattern for convergence (see the raster-scan video display manual for a detailed procedure). Push the one-player start button to end this test.

Figure 2-5 Convergence Pattern

SOUND TEST tests the twelve channels of the three Custom Audio sound chips. As the channel number is displayed, the test sound is played. The test continues to cycle through the channels until the one-player start button is pressed to end the test. The channels correspond to the three Custom Audio chips as shown in Table 2-4.

Page 21

Food Fight

Table 2-4 Sound Chip Locations

Chip No. Board Location Channels

111K/L5, 6, 11,-12
21IL/M1,2,7,8
311N3, 4,9, 10

Selecting the Statistics This is the second selection on the main self-test menu. Selecting STATISTICS causes the game statistics display to appear as shown in Figure 2-6. Press the one-player start button to end this test.

svaTisticsPusHsTamT1TO END

NUMBER OF GAMES TWO- PLAYER TOTaL COIN COUNT

00:00:00 00:00:00 00:50:30 IME 00:50:20 Et CJ Tal CREDITS

Figure 2-6 Statistics Display

The totals on the display are those accumulated since the Statistics were last reset. All statistics (except the last two) can be reset using the CLEAR VALUES, and STATISTICS

selectionsof the options menu. All times on the display are

shown as hours:minutes:seconds. The following statistics are displayed: NUMBER OF GAMES reads the number of one-player

games, the number of two-player games (increased by one

for each two-player game), and the total number of games. COIN COUNT reads the number of coins inserted through each of the right and left coin mechanisms. CREDITS reads the number of paid credits, free credits (entered using the auxiliary coin button), and the total credits since the statistics were last reset.

BONUS MEN EARNED reads the number of bonus lives (extra Chucks) earned at the first stage at higher stages using level select, and the total. It also shows the percentage of games played in which at least one bonus life was earned. Self-Test Procedures

AVERAGE TIME reads the average times between credits and games.

LONG GAME reads the longest time a player was able to play on one credit. TOTAL TIME ON reads the total time the game has been turned on since the statistics were last reset.

IN PLAY MODE reads the percentage of time the game has been in play mode (as opposed to attract mode) since the statistics were last reset.

NOTE The last two statistics cannot be reset. They are accumulated from the date the game was manufactured, or since the NVRAM last failed or was replaced.

TOTAL TIME reads the total amount of time the game has been turned on.

TOTAL CREDITS reads the total number of credits.

C. Selecting the Options

Selecting OPTIONS, the third selection on the main selftest menu, causes the options display shown in Figure 2-7 to appear. Use this display to view or change game option settings, or to clear the high scores or statistics. Push the THROW button to cycle through values on the current row (indicated in red). Change the current row using the joystick or the two-player start button. Push the one-player start button to end this display and make the displayed option settings the current settings.

OPTIONS MOVE JOYSTICK TO CHANGE ROW PUSH THROW TO CHANGE SETTINGS PUSH START 1 TO END » n ez TOAna CONSTANT ENGLISH OFe ONE OO>3MM= SCOP R-0n

© T & S f

ui a ry & Ci Ret I c € OBB ~O2“<<OD. aan ZRODMM:

bcO RESTORED wl>

Figure 2-7 Options Display

Page 22

Self-Test Procedures

To restore settings or to clear values, select the desired row and push the THROW button. RESTORED or CLEARED is then displayed. The options and settings available are listed in Table 2-5.

NOTE Turning off the self-test switch during this display will cause the current option settings, the high scores, and statistics to be unaffected.

Description of Option Terms

LIVES PER GAME sets the initial number of lives (Chucks), not including bonus lives, given for each credit. DIFFICULTY sets the game difficulty at levels 4 and above. Level 1 is easy, level 5 is hard. BONUS STAGES. sets the scores at which the first or subsequent bonus lives are awarded. Additional bonus lives are awarded when the score reaches a multiple of the higher bonus stage. For example, when the factory settings of 25,000 and 100,000 are in effect, bonus lives are awarded at 25,000; 100,000; 200,000; 300,000; etc. The first bonus stage may not exceed the second bonus stage. If the two are equal, only one bonus life is awarded when the score reaches the first bonus stage. For example, if both stages are set to 25,000, then bonus lives are awarded at 25,000; 50,000; 75,000; etc. Either one or both bonus stages can be turned off. LEVEL SELECT BONUS if turned on, awards bonus lives when the player uses level select to start the game at or above level 10. An extra life is awarded for starting at Food Fight

levels at or above every multiple of 10, with one additional life at level 125. For example, ten bonus lives would be awarded for starting at level 103. These bonus lives are given at the start of the game in addition to the LIVES PER GAME. The level at which bonus lives are earned and the current number of lives awarded are displayed with Chuck heads during level select.

LEVEL SELECT MODE effects how the level select feature is handled. There are four possible settings: ¢ NORMAL allows the player to select a starting level if the last game ended less than 15 seconds before, and if the maximum level achieved in the last game was greater than level one. If both of these cases hold, the player is allowed to select a starting level up to the maximum level achieved in the last game. © CONSTANT always allows the player to select a starting level up to at least level 9. If the last game ended less than 15 seconds before, the player is allowed to select up to the maximum level achieved in the last game. © DEMO always allows the player to select up to the maximum Food Fight level, for example, level 125. This setting would probably not be used for a game out on location, but is useful to demonstrate the performance of the game at high levels. © OFF causes no level select display to occur.

ATTRACT SOUNDS disables the attract mode sounds if in the OFF setting. COIN COUNTERS causes both coin mechanisms to drive the same coin counter if in the ONE setting.

Table 2-5 Option Settings

Option Settings Available Factory Setting

Lives per game2-53
Difficulty1-52
First bonus stageOff, 5000- 1,000,00025,000:
Higher bonus stageOff, 5000- 1,000,000100,000
Level select bonusOff/OnOn
Level select modeNormal, constant, demo, offConstant
Attract soundsOff/OnOn
LanguageEnglish, German, Spanish, FrenchEnglish
Cocktail modeOff/OnOff
Coin countersOne/TwoOne

2-6

Page 23

Food Fight

RESTORE SETTINGS resets the displayed option settings to one of the following: ¢ CURRENT displays the option settings in effect before the option menu was entered. e¢ FACTORY displays the option settings from the program ROM.

NOTE

Remember that the high scores and statistics will NOT be affected if the options menu is ended by turning off the self-test switch.

CLEAR VALUES resets the high-score table to its factory setting and resets to zero all the items on the statistics display, except for the TOTAL TIME and TOTAL CRED- ITS. The clear takes effect when the options menu is ended using the one-player start button. Self-Test Procedures

2-7

Page 24

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 25

Illustrated Parts Lists

This chapter provides information you need to order parts for your game. Common hardware (screws, nuts, washers, etc.) has been deleted from most of the parts lists. However, there is a parts list for the hardware to mount the game PCB and Regulator/Audio Il PCB to the cabinet.

The PCB parts lists are arranged in alphabetical order by component. Each component subsection is arranged alphanumerically by reference designator. Other parts lists are arranged alphanumerically by Atari part number. In these parts lists, all A-prefix numbers come first. Following these are numbers in sequence evaluated up to the hyphen, namely 00- through 99-, then 000598- through approximately 201000-. When ordering parts, please give the part number, part name, number of this manual, and serial number of your game. This will aid in filling your order rapidly and correctly. We hope the results will be less downtime and more profit from your game. Atari Customer Service numbers are listed on the inside front cover of this manual.

Chapter 3

Page 26

Food Fight Mustrated Parts Lists

Fluorescent Tube & Speaker ‘See Figure 35 03739201 178034-024 (Vent. grille) (T-Molding)

A039735-01 (Cabinet assy.)

Video Display {LZ See Figure 3-7 039752-01 pees , | A038881-01 (Display shield) bes | | ‘Lock) : ” Ey 037419-02 178013-001. (Access panel) (Latch) :

Gimbal Joystick See Figure 3-4 EMI Cage Gontrot:Panel See Figure 3-12 anel ic Game PCB lid See Figure 3-14

Utility Panel Assy. EMI Shield PCB See Figure 3-9 a See Figure 3-13

A039909-01 (Main harn. assy.) Coin Door “ ey)

See Figures 3-10 & 3-11 > Regulator! Saag Audio I PCB ? See Figure 3-15 = ‘A039910-01 038870-01 J (Power harn. assy) (Coin box enclosure) 178048-001 (Caster) , ©O

A037470-01 038091-01 (Coin box)

Power Suppl 7 ‘A037453-03 See Figure 3-16 soll (Power cord) 009992.01 78-3201 (On/off switch cover) (Glide)

Figure 3-1 Cabinet-Mounted Assemblies US-Built Game A039734-01 A

3-2

Page 27

Mlustrated Parts Lists, Food Fight

Cabinet-Mounted Assemblies Parts List

Part No. Description A037A5, Strain-Relief Power Cord (U.S. and Canada) A037470-01 Power On/Off Switch and Mounting Plate Assembly A038881-01 Lock Assembly (for rear access panel) Acceptable substitute is part no. A038881-03 A039735-01 Cabinet Assembly (includes glides and PCB retainers, but not the rear access panel)

A039909-01 Main Harness Assembly A039910-01 Power Harness Assembly

The following four items are technical information supplements to this game: SP-229 Food Fight Schematic Package $T-229-01 Food Fight Label with Self-Test Procedure and Option Switch Settings TM-160 Service Manual for 19-Inch Electrohome Color Raster Display (use with part no. 92-049) Acceptable substitute is TM- 220, for use with part no. 139003-1004 TM-229 Food Fight Operators Manual with Illustrated Parts List

78-3201 Adjustable Glide 009992-01 Power On/Off Switch Cover 036495-01 Speaker Grille (not shown) O37332-01 Ventilation Grille

037419-02 Rear Access Panel (does not include lock) 038091-01 Molded Coin Box 038870-01 Coin Box Enclosure 039752-01 Video Display Shield

178013-001 Spring Draw Latch 178034-024 34-Inch Black Plastic T-Molding, 178048-001 2-Inch Rigid Caster

3-3

Page 28

IMustrated Parts Lists Food Fight

Manuals, Schematics, & Self-Test Label— See parts list on following page

Fluorescent Tube & Attraction Panel See Figure 36

038992-01 (Display shield) ere (Vent. grille)

Video Display ————

178013-001 (Latch) rent

036891-01 (Speaker grille) ry 03897602 Control Panel = See Figure 3-3 5 (Access Panel) eee Gimbal Joystick

See Figure 3-4 Game PCB See Figure 3-14 Coin Door Assy. See Figures 3-10 & 3-11

A039999-01 038781-01 (Main harn. assy.) (Coin box. Utility Panel Assy. enclosure) See Figure 3-9 Regulatoi Audio it PCB See Figure 3-15

A040000-01 178034-024 (TMolding) (Power harn. assy.)

A037784-03 (Power cord) 03809101 8 > (Coin Box) 4 78-3201 we (Glide)

Power Supply See Figure 3-16

A037470-01 (Power on/off & switch assy.) 009892-01 (On/off switch cover)

Figure 3-2 Cabinet-Mounted Assembiies Ireland-Built Game A040005-02 A

3-4

Page 29

Food Fight IMlustrated Parts Lists

Cabinet-Mounted Assemblies Parts List

Part No. Description

A037470-01 A037784-03

A038881-01 A039999-01

A040000-01 A040006-01

ST-229-01 TM-160

72-68108, 78-3201 009992-01 034530-02

03689 1-01 03733201 038976-02 03809 1-01

OAB781-01 038992-01 14800 1-013 175004-708,

178013-001 178034-024 Power On/Off Switch & Mounting Piate Assembly Strain-Relief Power Cord (United Kingdom, Ireland, Lebanon, Saudi Arabia, India, Hong Kong, Singapore, Egypt, Nigeria, Republic of South African, Zimbabwe) Lock Assembly (for rear access panel) Main Harness Assembly

Power Harness Assembly Cabinet Assembly (includes glides and PCB retainers, but not the rear access panel)

The following five items are technical iyformation supplements to this game.

Food Fight Schematic Package Food Fight Label with Self-Test Procedure and Option Switeh Settings Service Manual for 19-Inch Electrohome Color Raster Display (use with part no. 92-049) or Service Manual for 19-Inch Wells Gardner Color Raster Display (use with part no. 92-055) Food Fight Operators Manual with Illustrated Parts List

#8 x %-Inch Cross-Recessed, Pan-Head Serew Adjustable Glide Power On/Off Switch Cover Foam Pad (not shown)

Speaker Grille Ventitation Grille Rear Access Panel (does not inelude lock) Molded Coin Box

Coin Box Enclosure Video Display Shield Speaker #8 Flat Fiber Washer

spring Draw: Latch %4-Inch Black Plastic T-Molding

Page 30

Illustrated Parts Lists. Pood Fight

Players may receive an electrical shock if this trol el Is not HORIZONTAL POTENTIOMETER properly ‘grounded! Atter servic: ing any parts on the panel, make ‘sure that the ground wire Is firm: ly attached to the meta! tab on the Inside of the control panel. RED

VERTICAL POTENTIOMETER 75-9810NO 75-5520B BLACK (Nut) ‘pat

160013-001 (Leaf switch & button holder)

178030-007 (Yellow pushbutton)

\>

62-039 (LED switch) g)— Ne (Switch bezel) (Locknut)

75-07020 (Washer)

‘A039911-01 (Harness)

A040012.01 (Control panel A039745-01 (Control panel with decal) with decal) 039749-04 039749-04 (Decal—not shown) (Decal-not shown) 039744-01 040013-01 (Control panel) (Contro! panel)

Figure 3-3 Control Panel Assembly US-Built Game A039746-01 A Ireland-Built Game A040011-01 A

3-6

Page 31

Food Fight Mlustrated Parts Lists

Control Panel Assembly Parts List

Description

Built AQ39745-U1 Control Panel with Decal FROM 12 Vinyl Foam Single-Coated Adhesive Tape, %-Inch Wide x Inch Thick (24 inches required) 030744 04 Control Panel O397HO-A Contol Panel Decal (not shown)

Ireland-Built Ag4O0} 2-0) Conurol Panel with becal 939749-04 Control Pane! Decal (nor shown) 0400 15-01 Control Panel 179 125-001 Grounding Ternunal (not shown)

US- and Ireland-Built A03 8838-02 Gimbal Joystick Assembly AOS99IL-OL Control Panel Harness Assembly, 62-039 SPDT Momentary Pushbutton Start Switch with Red Light-Emiuing Diode 75-07020 #°A Steel Flat Washer

75-5520B #%-20 x 1%-inch Black Carriage Bolt 7§-9910NO #% x 11 Stamped Nut 036895-01 Black Molded Switch Bezel 160013-001 Leaf Switch and Button Holder (leaf switch only is part no, 160012-001)

177010-244 #%-20 Hex Locknut 178030-007, Yellow Pushbutton Assembly

3-7

Page 32

IMlustrated Parts Lists

036953-01}5rs
(Square control|;NN

plate) 5 és

(Knob)

A038839-01iHy03695201|
(Pivot shaft assy.)\(Housing)

038842.01 (Shaft) ~— (Screw) 1 rises | (Slide plate) (Pivot ball)

i 03695401 “en {Mounting plate}

036955-01 (Bellows cap)

75-07020 (Flat washer) 75-0108 (Washer)

75-940S (Hex nut)

mS] (Linkage)

(inner gimbal) ~ | (Resistor)

036956-02 See Appendix A for lubrication (Outer gimbal) information.

Figure 3-4 Gimbal Joystick Assembly A038838-02 A

3-8

Page 33

Food Fight IMlustrated Parts Lists

Gimbal Joystick Assembly Parts List

Part No. Description

A037853-01 Bellows Assembly A038839-01 Pivot Shaft Assembly (includes pivot ball, pivot shaft and slotted pin) 19-9026 5kQ, +20%, 2% W Variable Resistor (acceptable substitute is part no. 119000-502) 72-5240 #10-32 x 24%-Inch, Zinc-Plated Steel Machine Screw

72-8406 #4-40 x Inch Socket-Head Steel Machine Screw 73-21224 ¥-Inch Diameter x 1 ¥2-Inch Long Slotted Pin 75-0108 #10 Flat Zinc-Plated Steel Washer 75-07020 ¥,Inch Interior Diameter Special Flat Washer 75-9408 #10-32 Self-Locking Hex Nut 036279-03 Pivot Ball 036952-01 Pivot Ball Housing (two required per handle) 036953-01 Square Control Plate

036954-01 Mounting Plate 036955-01 Bellows Cap 036956-01 Inner Gimbal 036956-02 Outer Gimbal

036957-01 Gimbal Linkage 036963-01 Slide Plate 038842-01 Pivot Shaft 039940-01 Pivot Ball Knob 178027-001 Nyogel 779 Lubricant

Page 34

Ulastrated Parts Lists Food Fight

148001-013 (Speaker) 70-304 (Tube) Be-i008 \ x (Tab)

179035-001 | = 79-561816P (Tube holder) Wire nut) ‘A097457-01 (Harness)

142028-001 (Transformer)

037480-01 (Bracket)

99-11003 (Starter)

99-11009 (Socket) (Ground wire)

036498-01 (Upper retainer) S

039751-01 (Attraction panel wi graphics)

78-6900404 (Tape)

003053-01 (Lower retainer)

NOTE

To ensure that the fluorescent tube starts, make sure the ground wire is firmly attached to both the ballast transformer and the steel tube bracket.

Figure 3-5 Fluorescent Tube and Speaker Assembly A039737-01 A US-Built Game

3-10

Page 35

Food Fight Mlustrated Parts Lists

Fluorescent Tube and Speaker Assembly Parts List

Part No. Description

A037457-01 Tube and Speaker Harness Assembly A037540-01 Ground Wire with Ring Lug 70-304 18-Inch, 15-Watt, Cool White Fluorescent Tube 78-6900404 Vinyl Foam Single-Coated Adhesive Tape, Y%-Inch Wide x 4-Inch Thick (48 inches required)

79-561816P Spring-Connector Wire Nut for 16- to 18-Gauge Wires 99-11003 Fluorescent Tube Starter 99-11006 Fluorescent Tube Locking Tab (consists of two pieces) 99-11009 Starter Socket

003053-01 Lower Attraction Panel Retainer 036498-01 Upper Attraction Panel Retainer 037469-01 Steel Tube Bracket 038151-01 15-Inch Jumper Wire

03975 1-01 Attraction Panel with Graphics 142028-001 148001-013, 179035-01 179125-001 60 Hz, 118-Volt, Ballast Trsformer (used on AO38161-01 assembly) 6 x 9-Inch Oval, 4 @, 6-Ounce, Shielded High-Fidelity Speaker 2-Pin Fluorescent Tube Holder Grounding Clip (not shown)

3-11

Page 36

Mlustrated Parts Lists Food Fight

040020-01 (Upper retainer) 99-11009 (Socket) 142028-002 (Transformer)

A005493-01 (Harness) 99-11003 (Starter)

035835-01 (Y-lead connector)

A040008-01 (Attraction panel w! graphics)

70-303 (Tube)

99-11012 (Clamp)

NOTE To ensure that the fluorescent ccxcrirs tube starts, make sure the (Lower retainer) ground wire ts firmly attached to the ballast transformer.

Figure 3-6 Fluorescent Tube and Attraction Panel Ireland-Built Game

Parts List

Part No. Description :

A005493-01 Fluorescent Tube Harness Assembly A040008-01 Attraction Panel with Graphics 70-303 18-Inch, 15-Watt, Cool White Fluorescent Tube 78-6900402 Vinyl Foam Single-Coated Adhesive Tape, 4-Inch Wide x %Inch Thick (not shown—48 inches required)

99-1103 Fluorescent Tube Starter 99-11009 Starter Socket 99-11012 1{-Inch Fluorescent Tube Clamp 035835-01 12-Inch Y-Lead Connector 038986-01 Lower Attraction Panel Retainer 040020-01 Upper Attraction Panel Retainer 142028-001 50 Hz, 118 V, Ballast Transformer

3-12

Page 37

Food Fight

76-6900402 (Tape) 039752.01 (Shield) 92.049 (Electrohome display)

039750-01 (Bezel)

Shock Hazard

The following procedure should only be performed by a qual service technician, Before removing or repairing the video display, unplug the game.

High voltages may exist in any video display, even with power disconnected. Use extreme caution and do not touch electrical

WARNING

parts of the display yoke area with your hands or with metal objects in your hands!

Discharge the high-voltage from the cathode ray tube as follows: Attach one end of a large, wellinsulated, 20-kV jumper to ground. Momentarily touch the free end of the grounded jumper to the anode by sliding it under Mlustrated Parts Lists

the anode cap. Wait two minutes: jischarge the anode again.

Implosion Hazard If you drop the display and the picture tube breaks, it will im- Plode! Shattered glass and the yoke can fly six feet or more from the implosion. Use care when replacing any display.

Figure 3-7 Video Display US-Built Game

Parts List

Part No. Description

78-0900402 Vinyl Foam Single-Coated Adhesive Tape, 4-inch Wide x Y-lnch Thick (24 inches required) Display Bezel Display Shield with Graphics 19-Inch Electrohome Color Raster-Scan Display Matsushita Color Raster-Scan Display) (Acceptable substitute is part no, 139003-1004—19-Inch

Page 38

Mlustrated Parts Lists

038992-01 038808-01 (Shield) (Bezel)

: 00272801 ee | (Bracket)

(Tape) H | Food Fight

‘gane0s-0 82.049 038804-02 (Retainer) (Electrohome display) or 92-055 (Wells Gardner display)

Figure 3-8 Video Display Ireland-Built Game Parts List

Part No. Description

78-6900402 Viny! Foam Single-Coated Adhesive Tape, '4-Inch Wide x Inch Thick (48 inches required—not shown) 92-049 19-inch Electrohome Color Raster-Scan Display or 92-055 19-Inch Wells Gardner Color Raster-Scan Display 002728-01 Metal Support Bracket

038804-02 038805-01 038808-01 038992-01 Display Shelf Display Shieid Retainer Display Bezel Display Shield

3-14

Page 39

Food Fight Mlustrated Parts Lists

A038004-01 (Harness)

179125-001 (Grounding Clip)

75-9810WO (Nut)

A002465-01 (Coin Counter) 62-041 (Auxiliary Coin Switch)

89-00 178070-001 (Self-Test Switch) (Volume Control Knob)

WARNING os Before removing or repairing the facket) utility panel, turn the game off. Players may receive an electrical (Volume Control) shock if the utility panel is not properly grounded! After servicing any parts on the panel, make ‘sure that the ground wire Is firmly attached to the metal screw ‘on the back of the coin counter.
NOTE Only the Ireland-Built cabinet has two coin counters.

Figure 3-9 Utility Panel Assembly A038002-01 & -02 G Parts List

Part No. Description

A002465-01 6 V Coin Counter A038004-05 Utility Panel Harness 19-9032 Volume Control 62-041 SPDT Momentary-Contact Pushbutton Auxiliary Coin Switch with Black Cap

69-005 DPDT Self-Test Switch 0380038-01 Utility Panel 75-9910W0 '%)-32 Stamped Nut 176018-002 #0-32 x Y-Inch Machine Screw

178070-001 Volume Control Knob 179125-001 Grounding Clip (not shown)

3-15

Page 40

Ilustrated Parts Lists Food Fight

170000-001 (Lamp) a 179047-001 ~ — 98-45023 (Lamp Base) > PSS (Base Plate) @ \

99-15056 (Screw tor Bezel) 99-15026 (Coin Inlet) 99-15025 Be (Coin Inlet)

Is. “ Is 2 9915054 ~~ (Pivot for Lever)

99-15028

(ene ‘(Coin Return Box)

75-056 (Lock Wash.)

<— 99-15060 (Sw. Cover)

(Switch)

72:1414S (Screw)

Figure 3-10 Vertically Mounted Coin Door 171034-xxx A

3-16

Page 41

Food Fight Ilustrated Parts Lists,

99-15067 DN (Lock Assy 99-15038 A037542-01 (Bezei for Button) (Harness—not shown)

99-15001 thru 99-15011 (Return Button)

99-15063 (Screw)

99-15052 (Spring for Button)

99-15071 (Clamp)

NN .

  • 99-15039 99-15067 = u (Bezel for Cover) (Lock Assy.) '99-15036 (Cover)

038091-01 (Coin Box) 99-15066 (Screw)

99-15072 (Door Frame) 99-15073, 99-15070 (Upper Door) | (Doors and Frame) 99-15074 (Lower Door)

171034-001 — U.S, 25¢/25¢ Coin Door 171034-006 — U.K. 20 P/50 P Coin Door 171034-011 — German 1 DM/5 DM Coin Door 171034-003 — Canadian 25¢/25¢ Coin Door 171034-009 — German 2 DM/1 DM Coin Door 171034.015 — French 2 Frit Fr Coin Door 171034005 — U.K. 10 P/50 P Coin Door 171034-010 — German 2 DM/S DM Coin Door

Figure 3-10 Vertically Mounted Coin Door, continued 171034-xxx A

Page 42

“fhastrated Bates Lists

Vertically Mounted Coin Door Parts List

Part No. Description

99.18 99-15002 99150048

99-15004 99-15005, 9Y-15000 y9-15007

99-15008 99-15009 99-18010 9015011

99-15023 9915025, 9915026 99-15027

9915028, 99-15029 99-15036 99-15038

9915039 99-15040, 99-15042 9915052

9915054 15055, 99-15056 99-15060

99-15063 99-15066, 9915067 99-15070.

99-15071 99-15072 99-15073 99-15074

99-15075 038091-01 170000-001 171006-035 179047-001 Harness Assembly 4-40 x %g-Inch Cross-Recessed Pan-Head Stee! Machine Screw #6 Intermal-Tooth Zine-Plated Steel Lock Washer #440 Stecl Machine Hex Nut

74-40 & T-Inch 82° Cross-Recessed Flat-Head Steci Machine Screw Coin Return Button with U.S. 25¢ Price Plate Coin Return button with U.S. $1 Price Plate Botton with Ge nT DM Price Phite

Coin Return Button with German 2 DM Price Plate Coin Return Button with German 3 DM Price Plate Coin Retarn Burton with Belgian 3 Fr Price Plate Coin Return Button with French | Fr Price Plate

Coin Return Button with Japanese 100 Yen Price Plate Coin Return Button with British 10 Pence Price Plate Coin Return Button with Australian 20¢ Price Plate Coin Return Button with Italian 100 Lire Price Plate

Base Plate Left Half of Coin Inlet Right Half of Coin inlet Side Plate of Coin Retum Box

Base Plate of Coin Return Box Switch Bracket Metal Coin Return Cover Bezel for Coin Return Button

Metal Bezel for Coin Return Cover Coin Return Lever Coin Switch for U.S Spring for Coin Return Button

Pivot for Coin Return Lever Retaining Screw #4-40 x },-Inch Cross-Recessed Pan-Head Steel Machine Screw Switch Cover

Screw for Hinge Screw for Clamp Lock Assembly Doors and Frame

Clamp for Frame Door Frame Upper Door Lower Door

Switch Adjuster Coin Box (Not included in assembh 6.3 V Miniature Wedge-Base Incan Metal Coin Mechanism Lamp Base —Acceptable substitute is part number A037491-01) scent Lamp

3-18

Page 43

Food Fight illustrated Parts Lists

171006-035 99-10140 (Coin mechanism) (Panel assy.)

75-948S a (Locknut) = oo 99-10116 (Lever)

99-10096 (Fastener) 75-9448 (Locknut)

99-10151 (Lett coin inlet)

70-11-47 (Lamp)

GF / (Bar retainer) 72-9406S. 7 (Screw) ~ 98-10147 A (Harness)

99-10154 (Bracket assy.)

99-10042 thru 99-10045 29-10183 (Coin switch assy) (Coin return box)

65-4410 (Coin switch) 98-10150

  • (Switch cover)

99-10075 thru 99-10078 (Switch wire) 99-10008. 7514128 (Retainer) (Screw)

Figure 3-11 American-Made Coin Door Assembly 171027-001 A

Page 44

Food Fight IMlustrated Parts Lists

99-10148 (Lock assy.)

99-10142 (Button housing) 72-HA1404C (Screw)

99-10139 (Coin door) —>} 99-10134 99-10119 (Cover) (Button assy) ) 9.10118 (Button)

99-10115 (Spring)

99-10141 {Coin return cover) (Cam)

99-10117 (Coin return door}

99-0144 e~ clip) Se

99-10149 (Service door)

038091-01 (Coin box) 99-10143 (Frame)

171034001 — U.S. 25¢/25¢ Coin Door 171034-006 — U.K. 20 PISO P Coin Door 171034-011 — German 1 DM/5 DM Coin Door 171034-003 — Canadian 25¢/25¢ Coin Door 171034-008 —- German 2 DM/1 DM Coin Door 171034015 — French 2 Frf1 Fr Coin Door 171034005 — U.K. 10 P/SO P Coin Door 171034010 — German 2 DMS DM Coin Door

Figure 3-11 American-Made Coin Doo: 171027-001 A

3-20

Page 45

Food Fight Illustrated Parts Lists

American-Made Coin-Door Assembly Parts List

Part No. Description

171006-035, Metal Coin Mechanism for U.S. $.25 65-441 Coin Switch 70-11-47 Miniature Bayonet Lamp 72-94068 #4-40 x ¥%-lnch Truss-Head Screw

72-HAL404C #4-40 x Vs-Inch Pan-Head Screw 72-JAI405B. #4-40 x .31-Inch Pan-Head Screw 75-14128 #4-40 x %-Inch Pan-Head Screw 75-9445 #4-40 Locknut

99-10008 99-10042 99-10043 99-10044

99-10045, 99- 10068 99-10075, 99-10076,

99-1007, 99-10078 99- 10080, 99-10081

99-10096 99-10 104 99-10105, 99-10 115

99-1016 99-10117 99-1011. 99-1019

99-1013 4 99-10139, 99-10140 99-1014 1

99-10142 99-10143 99-10144 99-10145,

99-10 146 99-10147 99-10148 99-10149,

99-10150, 99-10151 99-10152 99-10153 99-10154 Retainer Coin Switch Assembly for Belgian 5 Fr and U.S. $.25 Coin Switch Assembly for German 1 DM, Japanese 100 Yen, Swiss 1 Fr Coin Switch Assembly for German 2 DM, Italian 100 L, U.S. $1.00

Coin Switch Assembly for Australian $.20, German 5 DM, British 10 P in Return Chute Switch wire (included in coin switch assembly) Switch wire (included in coin switch assembly)

Switch wire (included in coin switch assembly) Switch wire (included in coin switch assembly) Lamp socket Key holder

Fastener Bar retainer Bar Spring,

Plasuc Coin Return Lever Steel Coin Return Door Amber Coin Return Button Amher Coin Button for U.S. $.25

Coin Button Cover Coin Door Coin Door Inner-Panel Assembly Diecast Coin Return Cover

Diecast Button Housing Coin Door Frame Coin Door Channel Clip Offset Cam

Coin Inlet Chute Assembly American-Made Coin Door Harness Lock Assembly Service Door

switch Cover Left Coin Inlet Right Coin Inlet Coin Return Box Bracket Assembly

3-21

Page 46

Ulustrated Parts Lists Food Fight

72-1604F (Screw) 24

176015-110 (Screw) 037873-01 (Spacer)

EMI Shield PCB d i

A

72-1404F (Screw) / L-

A037701-02 | (Cage) Ht

175009-221 EMI Shield PCB (Washer) See Figure 3-13 178044-242 oa9946-21 ame (Grommet) 1 2 (Fastener)

72-6810S 175004-708 175004-708 (Washer) (Washer)

034536-02 (Foam pad)

176015-110 (Screw)

(Regulator! Audio I! PCB) NOTE

Within the U.S. the FCC requires that the game PCB be housed in the EMI cage with the Shield PCB attached.

Figure 3-12 Electromagnetic Interference (EMI) Cage Assembly and Printed-Circuit Board Mounting Hardware

3-22

Page 47

Food Fight Ilustrated Parts Lists

EMI Cage Assembly and Printed-Circuit Board Mounting Hardware Paris List

Part No. Description

US-Built Game

A037701-02 EMI Cage (includes guide) A037430-02 EMI Shield PCB 72-1404F #4-40 x %-Inch Cross-Recessed Steel Screw 72-1604F #6-32 x 4-Inch Cross-Recessed Steel Screw

037873-01 Spacer 175004-708 #8 Flat Fiber Washer 175009-221 Plastic Washer 176015-110 #10 x %-Inch Cross-Recessed Pan-Head Screw

178044-242 Grommet 178045-442 Snap-In Fastener 179125-001 Grounding Clip (not shown)

Jreland-Built Game

034536-02 Foam Pad 175004-708 #8 Flat Fiber Washer 72-6810S #8 x %-Inch Cross-Recessed Pan-Head Screw

3-23

Page 48

Ilustrated Parts Lists

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden sithout the specific wetten permission of Atur, Inc., Sunnyale, CA, This draw only conditionally issued, and neither on ther Of confers or transfers any 1 use. the subject fmuatter of the drawing oF ai ieal information, shown thereon, nor any right to reproduce this drawingor any part thereof. Except for manufacture by venders of Atari Inc.. and for ‘manufacture under the corporation's written license, no Nght to reproduce this drawing is granted oF the subject matter thereof unless by written agreement with oF written permission from the corporation

Figure 3-13 EMI Shield PCB Assembly

3-24 iy y iy

t a PaeReeEORIEEE cso

A040253-01 A Food Fight

Page 49

Food Fight Ilustrated Parts Lists

EMI Shield PCB Assembly Parts List

DesignatorDescriptionPart No.

Capacitors

Cl-C3O.1 uF, +80% -20%, 50 V Ceramic-Disk Capacitor122002-104
csO.L uF, +80% -20%, 50 V Ceramic-Disk Capacitor122002-104
C6-C81000 pF, +5%, 100 V, NPO Ceramic-Disk Axial-Lead Capacitor (Acceptable122016-102

substitute is part no. 122002-102)

C9-Cl11470 pF, 100 V, NPO Ceramic-Disk Axial-Lead Capacitor(Acceptable122016-471

substitute is part no. 122013-471)

C12-C200.01 pF, +80% -20%, 25 V Ceramic-Disk Axial-Lead Capacitor122005-103
C21, C22O.1 wF, +80%-20%, 50 V Ceramic-Disk Capacitor122002-104
C24-C30O.L uF, +80% -20%, 50 V Ceramic-Disk Capacitor122002-104
C31-C39O.OL MF, +80% -20%, 25 V Ceramic-Disk Axial-Lead Capacitor122005-103
C40O.L uF, +80% -20%, 50 V Ceramic-Disk Capacitor122002-104

Connector

P2044-Pin Card-Edge Connector (Acceptable substitute is part no. 179046-044)179073-044

3-25

Page 50

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 51

Food Fight

Food Fight Game Printed-Circuit Board Assembly Illustrated Parts Lists

Parts List

DesignatorDescriptionPart No.

Capacitors

ClO.1 uF, +80%, -20%, 50 V, Ceramic Capacitor122002-104
C239 pF, 100 V Minimum, Dipped, Fixed-Mica Capacitor128002-390
3100 pF, 100 V Minimum, Dipped, Fixed-Mica Capacitor128002-101
C4O.1 HF, +80%, -20%, 50 V, Ceramic Capacitor122002-104
C5-C390.1 uF, +80%, -20%, 50 V, Ceramic Capacitor122002-104
C40-C470.1 uF, +80%, -20%, 50 V, Ceramic Capacitor122002-104
C48, C49.0.1 uF, +80%, -20%, 50 V, Ceramic Capacitor122002-104
C50-C520.1 uF, +80%, -20%, 50 V, Ceramic Capacitor122002-104
C53-C550.015 pF, + 10%, 100 V, Radial-Lead Mylar Capacitor21-101153
C560.001 pF, + 10%, 100 V, Radial-Lead Mylar Capacitor21-101102
C57100 pF, 35 V Aluminum Electrolytic Axial-Lead Capacitor24-350107
C58, C59O.1 uF, +80% -20%, 50 V, Ceramic Capacitor122002-104
c90100 wk, 35 V Aluminum Electrolytic Axial-Lead Capacitor24-350107
150150 uF, 100 V Mica Capacitor128002-151

Diodes

cRIType-MV5053 Light-Emitting Diode38-MV5053
CR2Type-IN756A, + 5%, 500 mW, 8.2 V Zener Diode32-1N756A

Inductors

Ll100 pH, + 10% Inductor141002-001
L2-L41H, + 10%, 830 mA, 0.29 Q, Peaking Coil Inductor141007-001

Integrated Circuits

1E‘Type-"4LS74 Integrated Circuit37-7ALS74
1F‘Type-74LS86 Integrated Circuit37-74LS86
1H‘Type-7407 Integrated Circuit37-7407
1K‘Type-74L$74 Integrated Circuit37-T4LS74
ILType-74804 Integrated Circuit37-74804
1MType-74LS163A Integrated Circuit37-TALS 163A
1NType-74LS 163AIntegrated Circuit37-74LS 163A,
IPType-74LS175 Integrated Circuit37-74LS 175,
2BType-74LS02 Integrated Circuit37-74LS02
2c‘Type-74508 Integrated Circuit37-74S08
2D‘Type-745157 Integrated Circuit37-748157
2E‘Type-74LS08 Integrated Circuit37-74LS08
2F‘Type-74L821 Integrated Circuit137210-001
2HType-74LS74 Integrated Circuit37-74LS74
3‘Type-74L832 Integrated Circuit37-74LS32
2K‘Type-74LS74 Integrated Circuit37-74LS74
2LType-74LS163A Integrated Circuit37-74LS 163A
2MType-74LS163A Integrated Circuit37-74LS 163A,
2NType-74LS163A Integrated Circuit37-74LS 163A
2PPROM Integrated Circuit136020-112

(Continued on next page)

3-27

Page 52

Illustrated Parts Lists Food Fight

Food Fight Game Printed-Circuit Board Assembly Parts List, continued

DesignatorDescriptionPart No.
3A‘Type-74LS157 Integrated Circuit37-74L$157
3BType-74LS 157 Integrated Circuit37-74LS157
3cType-74LS174 integrated Circuit37-74LS174
3DType-74LS299 Integrated Circuit137180-001
3EType-74L$299 Integrated Circuit137180-001
3F‘Type-74LS283 Integrated Circuit137204-001
3HType-74LS21 Integrated Circuit137210-001
3yType-74L8245 Integrated Circuit37-74L8245
3PType-74L5157 Integrated Circuit37-74LS157
4A‘Type-74S163 Integrated Circuit137274-001
4BType-74S163 integrated Circuit137274-001
4cType-74LS86 Integrated Circuit37-74LS860
4FType-74LS273 Integrated Circuit37-74LS273
4HType-74L$283 Integrated Circuit137204001
4Type-74LS86 Integrated Circuit37-74LSB6
4KType-74L$367 Integrated Circuit37-74LS367
4LType-74LS157 Integrated Circuit37-74LS157
4MType-74LS157 Integrated Circuit37-74LS157
4NType-74LS157 Integrated Circuit37-74L5157
4P‘Type-74S00 Integrated Circuit37-74800
5A.Type-74S 163 Integrated Circuit137274-001
5B‘Tvpe-74S163 Integrated Circuit137274-001
5HType-74LS377 Integrated Circuit37-74LS377
5)Type-74LS245 Integrated Circuit37-74L8245
5KType-74LS273 Integrated Circuit37-7ALS273,
SLType-74L8273 Integrated Circuit37-74LS273
5MType-74LS194 Integrated Circuit37-74LS8194
5NType-74L5194 Integrated Circuit37-74LS194
5PType-74LS32 Integrated Circuit37-TALS32
6BType-74LS273 Integrated Circuit37-74LS273
OH‘Type-74LS157 Integrated Circuit37-74LS157
ogType-74LS157 Integrated Circuit37-74L8157
6KType-74LS273 Integrated Circuit37-74LS273
ONType-74LS257 Integrated Circuit37-74LS257
oPType-74L8257 Integrated Circuit37-74L8257
KILType-74LS273 Integrated Circuit37-7ALS273
7M‘Type-74LS273 Integrated Circuit37-74L8273,
8K/LMicroprocessor Integrated Circuit137289-001
8MType-74LS244 Integrated Circuit37-74LS244
8N/PType-74LS244 Integrated Circuit37-T4LS244
8HType-74LS245 Integrated Circuit37-74LS245
8H‘Type-74LS245 Integrated Circuit37-74LS245,
8P‘Type-74LS02 Integrated Circuit37-74LS02
9HType-74LS245 Integrated Circuit37-74L8245

(Continued on next page)

3-28

Page 53

Food Fight

Food Fight Game Printed-Circuit Board Assembly Parts List, continued Illustrated Parts Lists

DesignatorDescriptionPart No.
OHType-7415245 Integrated Circuit37-TALS245
OK/LMicroprocessor Integrated Circuit137289-004
9MType-741S244 Integrated Circuit37-741S8244
OP.Type-74LS00 Integrated Circuit37-74LS00
10/KType-74LS14 Integrated Circuit37-74LS14
10CType-7406 Integrated Circuit37-7406
10EType-74L$32 Integrated Circuit37-74LS32
10C/D.Type-74LS 138 Integrated Circuit137177-001
10DType-74LS138 Integrated Circuit137177-001
10HType-74LS32 Integrated Circuit37-7ALS32
10HType-74LS74 Integrated Circuit37-7ALS74
10FType-74LS74 Integrated Circuit37-74LS74
10MType-74LS161 Integrated Circuit37-74LS161
10NType-74LS161 Integrated Circuit37-74LS161
10PProgrammed Logic Array Integrated Circuit137313-001
1IC/DType-74LS273 Integrated Circuit37-74LS273
uDType-74LS244 Integrated Circuit37-74LS244
HEType-74LS244 Integrated Circuit37-74L8244
11/12yQuad Op-Amp Integrated Circuit37-LM324
VIK/LCustom I/O Integrated Circuit€012294-01
11L/MCustom I/O Integrated Circuit€012294-01
11NCustom I/O Integrated Circuit€012294-01
12DD-to-A Converter Integrated Circuit137243-001

Miscellaneous

Q2, @Nylon Snap-In Fastener81-4302

Test Point (Acceptable substitute is part no. 020670-01) 179051-002

YI12.096 MHz Crystal144000-001
swi8-Station Single-Throw Dual-Inline Package Bit Switch66-118P1T

Erasable Programmable Read-Only Memories

4EErasable Programmable Read-Only Memory136020-110
4DErasable Programmable Read-Only Memory136020-111
6L/MErasable Programmable Read-Only Memory136020-109
8cErasable Programmable Read-Only Memory136020-301
8DErasable Programmable Read-Only Memory136020-303
8EErasable Programmable Read-Only Memory136020-305
8FErasable Programmable Read-Only Memory136020-307
9CErasable Programmable Read-Only Memory136020-302
9DErasable Programmable Read-Only Memory136020-204
9EErasable Programmable Read-Only Memory136020-306
oFErasable Programmable Read-Only Memory136020-308

Random-Access Memory

3KStatic RAM Integrated Circuit90-7036
3LStatic RAM Integrated Circuit90-7036,
3MStatic RAM Integrated Circuit90-7036,
3NStatic RAM Integrated Circuit90-7036

(Continued on next page)

3-29

Page 54

Illustrated Parts Lists Food Fight

Food Fight Game Printed-Circuit Board Assembly Parts List, continued

DesignatorDescriptionPart No.
SCRandom-Access Memory157178-001
5DRandom-Access Memory137178-001
SERandom-Access Memory137178-001
SFRandom-Access Memory137178-001
6cRandom-Access Memory137250-001
6DRandom-Access Memory137250-001
OERandom-Access Memory137250-001
OFRandom-Access Memory137250-001
INRandom-Access Memory137178-001
7PRandom-Access Memory137178-001
8ARandom-Access Memory137211-001
8BRandom-Access Memory137211-001
9ARandom-Access Memory137211-001
OBRandom-Access Memory137211-001
ONNon-Volatile RAM Integrated Circuit137288-001

Resistors

RI220 Q, +5%, % W Resistor110000-221
R2, R310kQ, +5%, %& W Resistor110000-103,
R41kQ, £5%, 4 W Resistor110000-102
R5-R71kQ, +5%, % W Resistor110000-102
R8.1kQ, +5%, “& W Resistor110000-102
RO1kQ, +5%, 4 W Resistor110000-102
R1O1kQ, +5%, % W Resistor110000-102
RII470 Q, +5%, % W Resistor110000-471
R121kQ, +5%, 4 W Resistor110000-102
R13, R14220 Q, +5%, 4 W Resistor110000-221
RIS470 Q, +5%, 4 W Resistor110000-471
RIG1kQ, 45%, 4 W Resistor110000-102
RI7470 Q, +5%, % W Resistor110000-471
R18220 Q, +5%, %& W Resistor110000-221
RIO1kQ, +5%, % W Resistor110000-102
R20-R231kQ, +5%, % W Resistor110000-102
R24-R274.7kQ, +5%, % W Resistor110000-472
R28220 Q, +5%, % W Resistor110000-221
R29220 2, £5%, % W Resistor110000-221
R301kQ, +5%, % W Resistor110000-102
R31470 Q, +5%, % W Resistor110000-471
R321kQ, +5%, 4 W Resistor110000-102
R33470 Q, +5%, % W Resistor110000-471
R341kQ, +5%, 4 W Resistor110000-102
R35,470 Q, 45%, 4 W Resistor110000-471
R361kQ, +5%, % W Resistor110000-102
R37470 Q, 45%, 4 W Resistor110000-471
R381kQ, +5%, % W Resistor110000-102

(Continued on next page)

Page 55

Food Fight

Food Fight Game Printed-Circuit Board Assembly Parts List, continued Illustrated Parts Lists

DesignatorDescriptionPart No.
R39470 Q, +5%, % W Resistor110000-471
R401kQ, +5%, % W Resistor110000-102
R41470 Q, +5%, % W Resistor110000-471
R421kQ, +5%, % W Resistor110000-102
R43470 2, +5%, % W Resistor110000-471
R441kQ, 45%, % W Resistor110000-102
R45470 Q, +5%, % W Resistor110000-471
R4610kQ, +5%, 4 W Resistor110000-103
R47-R49100 kQ, +5%, % W Resistor110000-104
RS50-R5747kQ, +5%, % W Resistor110000-472
R5810kQ, +5%, 4 W Resistor110000-103
R59-621kQ, +5%, 4 W Resistor110000-102
R63-R6710kQ, +5%, % W Resistor110000-103
ROB22 kQ, +5%, 4 W Resistor110000-223
RO9-R71330kQ, +5%, 4 W Resistor110000-334
R72-R74910 2, +5%, % W Resistor110000-911
R75220 Q, +5%, % W Resistor110000-221
R761kQ, 45%, %4 W Resistor110000-102
R77220 Q, +5%, % W Resistor110000-221
R784.7 kQ, 45%, '4 W Resistor110000-472
R79330 Q, +5%, % W Resistor110000-331
R90, R914.7kQ,5%, 4 W Resistor110000-472
R150330 kQ, +5%, 4 W Resistor110000-331
R2071kQ, 45%, % W Resistor110000-102

Sockets

4D28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
4E28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
SC22-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C22
5D22-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C22
SE22-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C22
SF22-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C22
oc22-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C22
6D22-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C22
6E22-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C22
OF22-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C22
6L/M28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
7N22-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C22
7P22-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C22
8A24-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C24
8B24-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C24
8C28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
8D28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
8E28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
8F28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
8K/L64-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C64

(Continued on next page)

3-31

Page 56

Illustrated Parts Lists Food Fight

Food Fight Game Printed-Circuit Board Assembly

Parts List, continued

DesignatorDescriptionPart No.
9A24-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C24
OB24-Contact Medium-Insertion-Force Integrated CircuitSocket79-42C24
9c28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
9D28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
9E28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
OF28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
OK/L64-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C64
10P20-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C20
TIK/L40-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C40
1IL/M40-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C40
1IN40-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C40
12D28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28

Transistors

QlType-2N3904, 350 mW, 60 V NPN Transistor34-2N3904
Q2, Q3Type-2N6044, 8 A, 80 V NPN Transistor34-2N6044
Q4Type-2N3904, 350 mW, 60 V NPN Transistor34-2N3904

3-32

Page 57

Food Fight

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproducton forbidden without the specific i, Inc., Sunnyvale, CA, a. and neither receipt oF license fect matter of the drawing or any design or techni shown thereon, nor any right tO reproduce this drawing or any part thereof. Except for manufacture hy vendors of Atari, Inc and for manufacture under the corporation's written license. 0 right to reproduce this drawing is granted or the subject matter thereof unless by written agreement with or writen permission from the corporation. Ilustrated Parts Lists

R33

2 I. 4

”F885—

ox 9

g“a5

ce Me co oy

c20cay0

Cy

—-r3300—

35V

C18 no

p32 fa S.6K

a LOR

fe)Bafra7WwEOo

q

TIP 32_TOAZ002ATDA2002A
Saaz INé Coz Qs ; TTjlQ7
Ceeopco.
ae ASBS cram3
0SSIRS{|, CoGestcis
ce Gan{|eTERIRIA GO|R22cl4

[2201 R21 ew

]22Jczyb
0zh] 232470*

COIR Jooaoa coicid] 470 TA} RI Rites

° NI]soeC10
5ame+
-0820)es

R30 RI 1/2W FD cri

(oe07m)6

°

—4+33004F|
5aSav

Figure 3-15 Regulator/Audio II PCB Assembly A035435-04 K

3-33

Page 58

Illustrated Parts Lists

Regulator/Audio II PCB Assembly Food Fight

Parts List

Designator Description

Capacitors

cl470 yF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-250477
C20.001 pF, 50 V, Ceramic-Disc Axial-Lead Capacitor122002-102
c30.1 pF, 50 V, Ceramic-Disc Axial-Lead Capacitor122002-104
C4470 wF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-250477
cs0.01 pF, 25 V Minimum, Ceramic-Disc Axial-Lead Capacitor (Acceptable100015-103

substitute is part no. 122005-103)

CO0.22 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor122004-224
CT0.001 yF, 50 V, Ceramic-Disc Axial-Lead Capacitor122002-102
C80.22 pF, 25 V, Ceramic-Dis¢ Axial-Lead Capacitor122004-224
C9; C103300 wF, 35 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-350338.
cll0.1 pF, 50 V, Ceramic-Disc Axial-Lead Capacitor122002-104
Cl470 yF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-250477
C131000 pF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-250108
Cl40.01 WF, 25 V Minimum, Ceramic-Dise Axial-Lead Capacitor100015-103

(Acceptable substitute is part no. 122005-103)

Cis0.22 wF, 25 V, Ceramic-Disc Axial-Lead Capacitor122004-224
C160.001 wF, 50 V, Ceramic-Disc Axial-Lead Capacitor122002-102
Cl70.22 yF, 25 V, Ceramic-Disc Axial-Lead Capacitor122004-224
C18, C3300 uF, 35 V, Aluminum Electrolytic Fixed AxialLead Capacitor24-350338
€20,O.1 pF, 50 V, Ceramic-Dise Axial-Lead Capacitor122002-104

Diodes

CRI, C4Type-1N4002, A, 100 V Silicon Rectifier Diode31-1N4002
CR5-CR8BType-1N5401, 3 A, 100 V Silicon Rectifier Diode31-1N5401

Integrated Circuits

alType-LM305, 5 V, Linear Voltage Regulator37-LM305
QsType-TDA2002A, 8 W, Lincar Audio Amplifier Integrated Circuit137151-002
Q7Type-TDA2002A, 8 W, Linear Audio Amplifier Integrated Circuit137151-002

Resistors

Rl270 Q, +5%. 4 W Resistor110000-271
R333 Q, +5%, Ve W Resistor110000-330
R4100 Q, +5%, Ye W Resistor110000-101
RS2.7Q, +5%, 1 W Resistor110009-027
RG3.9 kQ, +5%, vs W Resistor110000-392
R?7.5 kQ, +5%, & W Resistor110000-752
R81 kQ Horizontal PCB-Mounting Cermet Potentiometer (Acceptable119002-102

substitute is part no. 19-315102)

RO2202, +5%, % W Resistor110001-221
R1012, +5%, % W Resistor110000-010
Ril102, +5%, 4 W Resistor110000-100
R12100 2, +5%, %4 W Resistor110000-101
R13, R1410 kQ, +5%, %4 W Resistor1 LQ0UU- 103

(Continued on next page)

Page 59

Food Fight Illustrated Parts Lists

Regulator/Audio II PCB Assembly Parts List, continued

DesignatorDescriptionPart No.
R191Q, +5%, % W Resistor110000-010
R2010 2,5%, 4 W Resistor110000-100
R21220 2, +5%, % W Resistor110001-221
R22100 2, +5%, 4 W Resistor110000-101
R240.1.2, +3%, 7 W Wirewound Resistor19-100P 1015,
R27, R281kQ, +5%, 4 W Resistor110000-102
R29, R30102, +5%, % W Resistor110000-100

R33 5.6 kQ, 45%, % W Resistor 110000-562

Transistors

Q2‘Type-TIP32 PNP Power Transistor33-TIP32
QType-2N3055 NPN Silicon Transistor34-2N3055

Mechanical Parts

J66-Position Connector Receptacle79-58306
ae9-Position Connector Receptacle79-58308
J84-Position Connector Receptacle79-58354
JO6-Position Connector Receptacle79-58306
Jio12-Position Connector Receptacle79-58346
Q2#6-32 x %-Inch Binder-Head Nylon Screw75-F60405
Q3#6-32 Nut/Washer Assembly75-99516
Q3Thermally Conductive Silicon Insulator78-16008.
Q5Thermally Conductive Silicon Insulator78-16008
Q5, Q7#6 x YeInch Cross-Recessed Pan-Head Thread-Forming Type-AB Zinc-72-6606

Plated-Steel Screw

Heat Sink 03453101 Test Point (Acceptable substitute is part no. 020670-01) 17905 1-001

3-35

Page 60

Iustrated Parts Lists Food Fight

WARNING Fuse block cover must be In place during game operation. A035888-01 (Transtormer assy.)

A021084-xx. (Voltage plugs) 29-053 (Capacitor) 034544-01 (Fuse block cover)

79-4411001 (Fuse post)

78-70501SC (Capacitor bracket)

(Fuse)

A035891-02 (Fuse harness assy} 034482-02 VA (Chassis) 46-301203 (Fuse)

78-2708 (Bushing)

A034630-01 (Filter Assy.) 79-3206 (Fuse block) 46-2014002 (Fuses)

79-15021001 A035890-01 (Terminal block) (Power harness)

A034629-01

Assembly

3-36

Page 61

Food Fight

Power Supply Assembly Parts List US-Built Game A037671-01 G Iustrated Parts Lists

Designator Description Part No.

cl27,000 uF, 15 VDC Electrolytic Capacitor29-053
cl2-Inch Diameter Capacitor Mounting Bracket78-70501SC
CRI‘Type-MDA 3501 Bridge Rectifier3A-MDA3501
FLPanel-Mounting Non-Indicating 3AG Cartridge-Type Fuse Post79-4411001
FL7 A, 250 V, 3AG Slow-Blow Glass Cartridge-Type Fuse46-2017002
FlLabel for Fuse Value037639-01
F24A, 250 V, 3AG Slow-Blow Glass Cartridge-Type Fuse46-2014002
F2-F65-Position 3AG Fuse Block with %-Inch Quick-Disconnect Terminals79-3206
F2-F6Fuse Harness AssemblyA035891-02
F2-F6Fuse Block Cover034544-01
F2-F6Label for Fuse Values037640-01
F320 A, 32 V, 3AG Slow-Blow Glass Cartridge-Type Fuse46-301203
F42-Circuit Single-Row Terminal Block (located under F4)79-15021001
F4-F64A, 250 V. 3AG Slow-Blow Glass Cartridge-Type Fuse46-2014002
FLIRFI Filter Assembly (designation not marked)A034630-01
J2Power Harness AssemblyA035890-01
3BVoltage Plug for 120 V (105-135 VAC) (yellow wire color—plugs into J3)A021084-02
J4aAC Harness AssemblyA034629-01
TlTransformer Assembly (designation covered—Acceptable substitute is part no.‘A035888-01

A035888-02) Nylon Type 6/6 Hole Bushing with %-Inch Inside Diameter x °%4-Inch 78-2708 Outside Diameter x %-Inch Thick

Power Supply Chassis Base 034482-02 Metal Base Plate (not shown in illustration) 037243-01

3-37

Page 62

Ilustrated Parts Lists

Power Supply Assembly Parts List Ireland-Built Game A037671-03 G Food Fight

DesignatorDescriptionPart No.
cl27,000 pF, 15 VDC Electrolytic Capacitor29-053,
cl2-Inch Diameter Capacitor Mounting Bracket78-705018C
CRIType-MDA 3501 Bridge Rectifier3A-MDA3501
FIPanel-Mounting Non-Indicating 3AG Cartridge-Type Fuse Post79-441101
FILabel for Fuse Value037639-02
Fl, F24 A, 250 V, 3AG Slow-Blow Glass Cartridge-Type Fuse46-2014002
F2-F65-Position 3AG Fuse Block with %-Inch Quick-Disconnect Terminals79-3206
F2-F6Fuse Harness AssemblyA035891-02
F2-F6Fuse Block Cover034544-01
F2-F6Label for Fuse Values037640-01
F320 A, 32 V, 3AG Slow-Blow Glass Cartridge-Type Fuse46-301203
Fa2-Circuit Single-Row Terminal Block (located under F4)79-15021001
F4-F64A, 250 V, 3AG Slow-Blow Glass Cartridge-Type Fuse46-2014002
FLIRFI Filter Assembly (designation not marked)A034630-01
J2Power Harness AssemblyA035890-01
J3Voltage Plug for 220 V (200-240 VAC) (blue wire color—plugs into J3)A02 1084-04
J3Voltage Plug for 240 V (220-260 VAC) (brown wire color—plugs into J3)A021084-05
J4aAC Harness AssemblyA034629-01
TITransformer Assembly (designation covered—Acceptable substitute is part no.A035888-01

A035888-02) Nylon Type 6/6 Hole Bushing with ¥,Inch Inside Diameter x *%-Inch Outside Diameter x %-Inch Thick

Power Supply Chassis Base Metal Base Plate (not shown) 78-2708

034482-02 037243-01

Page 63

Gimbal Joystick Maintenance and Repair

Before removing or repairing the joystick, turn the game off.

Normal maintenance involves lubricating four parts in the joystick control approximately every three months (this requires removing the control). First, open the control pancl. Tilt the control panel towards you. Then unsolder the harness from the two potentiometers on the joystick assembly. From the inside of the control panel, remove the four flat washers, hex nuts, and carriage bolts that mount the joystick to the control panel Then open up the joystick control assembly by removing, the four flat washers, hex nuts, and long screws (see Figure 3-4). At this point, most of the parts should disassemble. For lubrication, use only Nyogel 779 lubricant (Atari part no. 178027-001). Lubricate the following parts inside the control: © — The insides of the two black linkages, located on the potentiometer shafts © — The insides of the two gimbals, where the bottom of the shaft wears against them. © — The sides of the pivot ball housings at the four holes where the gimbals are attached. If the bellows need replacing, remove both gimbals and the bellows cap. Slide the bellows off the bottom of the shaft, Slide the new bellows up over shaft

Reassemble the joystick control, and then reinstall it in the control panel. Reconnect the harness wires as shown in Figure 3-3, Make sure the right colors go to the tabs on the potentiometers. Refer to Chapter 2, Self-Test Menu, for instructions on how to recalibrate the joystick.

Appendix A

If the square pattern control plate (part no. 036953-01) or mounting plate (part no. 036954-01) need replacing, disassemble the lower half of the control by removing the four hex nuts. Support the pivot ball of the pivot shaft assembly on a hard surface that has a hole slightly deeper than the length of the rolf pin (see Figure A-1). Knock out the #.-inch roll pin using a #,-inch punch. Reassemble in reverse order.

%e-inch punch

Pivot bail a

Figure A-1 Disassembling

the Pivot Shaft Assembly

AL

Page 64

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 65

Food Fight™ 3rd printing

YOUR COMMENTS, PLEAS

Your comments will assist Atari in improving Our publications. The comments are an important part of preparing for revisions of game manuals. Please write in the space below. No postage stamp is necessary if mailed in the U.S.A.

If you have any technical questions about certain ATARI games products, of are requesting additional publications, we will immediately forward your note to the appropriate person.

Page: Comments:

Fill in if you wish a reply

Name

Firm © Distributor

Address Tl Operator

City State Zip (J Other

Area Code Phone

Page 66

First Fold

age cessary if

BUSINESS REPLY MAIL

FIRST CLASS PERMIT NO. 1004 SUNNYVALE, CA

POSTAGE WILL BE PAID BY ADDRESSEE

Atari, Inc. Attn.: Field Service/Coin-Op Division P.O. Box 427 Sunnyvale, California 94086

Second Fold

odd

a8po spp ade,

Page 67

Food Fight™ 3rd printing

YOUR COMMENTS, PLEASE!

Your comments will assist Atari in improving our publications. The comments are an important part of preparing for revisions of game manuals. Please write in the space below.

If you have any technical questions about certain ATARI games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.

Page: Comments:

Fill in if you wish a reply

Name

Firm we Distributor

Address &. Operator

City Country < Other

Phone: Country Code: Local Number

Page 68

First Fold

Attach Necessary Postage

Atari Ireland Limited Attn.: Field Service/Coin-Op Division

Tipperary Town, Ireland

Second Fold

wos

apa snp adey,

Page 69

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 70

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 71

PEG LWE, SRR GE GE YE EE SS SE ES

Warranty

Seller warrants that its printed-circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its video displays (in games supplied with displays) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment. None of the Seller's other products or parts thereof are warranted. If the products described in this manual fail to conform to this warranty, Seller’s sole liability shall be, at its option, to repair, replace, or credit Buyer’s account for such products which are returned to Seller during said warranty period, provided: {a) Seller is promptly notified in writing upon discovery by Buyer that said products are defective; (b)Such products are returned prepaid to Seller’s plant; and (c)Selier’s examination of said products discloses to Seller’s satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation, or improper testing. In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages. Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms herein, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller’s part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products by Seller.

The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to you and others. Be very cautious in using non-Atari-supplied components with our games, in order to insure your safety. Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories. Atari cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor.

Page 72

A

ATARI

ATARI, INC. 790 SYCAMORE DRIVE P.O, BOX 906 MILPITAS, CALIFORNIA 95035 408/942-3100 ¢ TELEX 35-7488