CATHODE RAY TOMES

The Main Event Instruction Manual

The Main Event (4 Players ver. Y) (Konami, 1988) · Instruction Manual · 11 pages · 16 sections · original scan

Page 1

od KONAMI

INSTRUCTION MANUAL

MAIN EVENT™ is a registered trademark of Konami Inc, © 1988 Konami Inc. Py KONAM?? is a trademark of Konami Industry Co,, Ltd.

Page 2

MAIN EVENT:

WIRE COLOR KEY:

WIRING HARNESS

Solder Side <—__—__ > Parts Side

BLACK

BLACK

RED

RED

ORANGE

YELLOW

WHITE/GREEN

WHITE

VIOLET/WHITE

RED/GREEN

BLUE/YELLOW

VIOLET/YELLOW

ORANGE/GREEN

ORANGE/YELLOW

BLACKIYELLOW

ORANGE/GRAY

BLACK

BLACK GND

GND

» +5V DC

+5V DC

NOT USED

+12V DC

*KEY

(EMPTY)

(EMPTY)

SPEAKER (-)

{EMPTY)

VIDEO GREEN

VIDEO SYNC

(EMPTY)

(EMPTY)

COIN 2

2P START

2P UP

2P DOWN

2P LEFT

2P RIGHT

2P TAG

2P ACTION

NOT USED

NOT USED

NOT USED

GND

GND A | 1 | GND | B | 2 | GND c | 3 | +5v0c bp | 4 | +svbc

  • | 5 | NOTUSED F [ 6 | +12vDC H | 7 | *KEY J | 8 | COIN COUNTER « | 9 | (EMPTY) L | 140 | SPEAKER (+) m | 11 | (empty) nN | 12 | VIDEO RED P | 13 | VIDEO BLUE R | 14 | VIDEO GROUND s | 15 | MPTy) ' tT | 16 | COIN4 u | 17 | 1P START v | 48 | 1PUP w | 19 | 1p DowN x | 20 | 1PLEFT | -y | 21 | 1P RIGHT z 22 | 1PTAG a | 23 | 1P ACTION b | 24 | NOT USED c | 25 | NOTUSED } d | 26 | NOTUSED e t 27 | GND

f 28 | GND

(BASE COLORILINE COLOR) BLACK

BLACK

RED

RED

ORANGE

GREEN/GRAY

BLUE

RED/WHITE

BLUE/WHITE

BLACK

BLUE/BROWN

PINK/YELLOW

ORANGE/WHITE

BLACK/WHITE

RED/GRAY

GRAY/WHITE

RED/WHITE

GREEN/BROWN

BLACK

BLACK

Page 3

MAIN EVENT: SUB HARNESS

CN3 3P CONTROLS

CNS ap CONTROLS

CN2 ACTION LAMP OUTPUTS Coin 3

Empty

3P Left 3P Right 3P Up 3P Down 3P Tag 3P, Action

Ground

Coin 4

4P Left 4P Right 4P Up 4P Down 4P Tag 4P Action

Ground

Lamp 1 Lamp 2 Lamp 3 Lamp 4

+ 12 Volts White/Violet

White/Red White/Yellow White/Black White/Blue White/Brown White/Orange

Black

Blue

Yellow/Black Brown/Black Green/Yellow Yellow/Red Yellow/White Yellow/Blue

Black

Violet Blue Green Yellow

Black

Page 4

DIP SWITCH SETTINGS

DIP SWITCH NO. 1 SETTINGS

  • COIN 1
SW1234COIN |CREDIT;
.OFF | OFF | OFF | OFF11
ON12
OFFON13
ON14
OFF | OFFONOFF15
ON16
OFFON17
ON21
OFF | OFF | OFFON23
ON25
OFFON31
ON32
OFF | OFFONON34
ON41
OFFON43
ON45

SWS5 through SW8 are not used.

DIP SWITCH NO. 2 SETTINGS 1, BONUS ENERGY

sw12ENERGY
|OFF | OFF90
.ON80
OFFON70|

ON 60

  • DIFFICULTY OF THE GAME
sw67DIFFICULTY

OFF | OFF EASY

.ONNORMAL

OFF ON DIFFICULT

ON VERY DIFFICULT

  • SOUND IN ATTRACTIVE MODE sw | 8 SOUND OFF OFF + | oN ON

SW 1, SW2 and SW3 are not used.

DIP SWITCH NO.3 SETTINGS

  • VIDEO SCREEN FLIP

Sw 1

.OFFNORMAL

ON UPSIDE DOWN

  • CHANGE OF MODE
SW3MODE
.OFFGAME

ON TEST

SW2 and SW4 are not used.

  • Shows recommended settings
Page 5

=

MAIN EVENT: AC FLOW CHART

1, GREEN/YELLOW 2, BLACK

  • RED
  • BLUE
  • BROWN
  • RED/BLACK
  • BLACK/WHITE
  • WHITE
  • GREEN 10, VIOLET 11, ORANGE LINE CORD

NOISE FILTER

MAIN SWITCH (Top of Cabinet)

ISOLATION TRANSFORMER POWER SUPPLY

4 AMP FUSE FLOURESCENT Me

Page 6

PARTS SIDE

MAIN EVENT: WIRING DIAGRAM SOLDER SIDE

(ijt Gro pon No a REQUIRED POWER CAPACITY a...

+5V +5Y [ay +3v a oesv ee ae {_6] +12V

COIN COUNTER 1 CONTROL FOR 3P

SAME AS 1P CONTROLS

[ry

COIN COUNTER CN3 EXTENSION 1/6 J 15P NH CONNECTSR

BI5P-SHF-1AA JST

SPEAKER (+) SPEAKER (~) CN2 LAMP OUTPUT 6P VH CONNECTER

RED B6PS-VH JST

GREEN BLUE SYNC VIDEO GNO LAMP 14 COLGR MONITOR

l COIN’ 1 LAMP 3

COIN 2 1P START

1P uP 2P UP 1P DOWN 2P DOWN 1P LEFT 2@P LEFT 1P RIGHT 2P RIGHT COIN4 1P TAG 1 N.C CONTROL FOR 4P aP TAG 21,5 ACTION 3 SAME AS 1P CONTROLS

2P ACTION AME

CONTROL FAR 2P

SAME AS 1P CONTROLS

CONTROL FOR 1P

ACTION TAG RIGHT LEFT uP 27 GND GND Down Zwc 28 GND 13) *.

  • NOTES - GND Lt} GNo +2 ono 1 1P NO.1 PLAYER 2P N@.2 PLAYER a5 — — CN4 EXTENSION I/O 3P.NO.3 PLAYER © 4P_NO.4 PLAYER JAMA 56PIN EDGE CONNECTOR 15P NH CONNECTOR + 2 SURGE KILLER OIODES FOR COIN 9/92 INCH PITCH BIS SHEIK IST

COUNTER INSTALLED ON THE P.C.B. 1P_TAG 1P_ACTION

Page 7

COMPLETE COIN DOOR ASSEMBLY

EXPLODED VIEW

0-1900-00 L, (90-1000-00-—~ T !

#1-1109-00.

91-1922-00 —" of 91-1117-00 ——+ 91-1119-00

91-1127-00"

PARTS LIST 12-4050-01 $-10 Acceptor Body U.S. 25° 12-4050-03 S-10 Acceptor Body Canadian 25* 20-4177-00 Plastic Cash Box 20-4179-00 Stee! Enclosure 22-1400-00 Locking Bar 24-1150-00 Wire Harness 90-1000-00 Keyhook Bezel Screw 90-1001-00 Bezel Screw 90-1092-00 Hinge Screw 90-1003-00 Clamp Screw 90-1007-00 Flat Head Microswitch Mounting Screw 90-1008-00 — Panhead Microswitch Mounting Screw or-i1t8. 91-1141-00

90-1007-00

90-1102-00

90-1207-00

90-1300-00 91-0502-00 91-0503-00 91-0504-00 91-0505-00

91-0506-00 91-0515-00

91-0535-00

91-0545-00 Washer for Bezel Screw Nut for Microswitch Mounting Screw Keyhook Zinc Die Cast Frame ‘Lower Door Upper Door Round Lock and Cam Assembly Clamp Flat Lock and Cam Assembly Flat Lock and Cam Assembly Round Leck and Cam Assembly 91-1103-00 91-1104-00 91-1105-00 91-1106-00 91-1107-00 91-1108-01 91-1109-00 91-1110-00 94-1111-00 91-1112-00 91-1113-01

91-1116-00

91-1117-00 91-1118-00 91-1111-90 99-1211-00

91-1119-01 go vretteo 2 3-1112-00 1-12 12-00, es

Coin Inlet Lamp Side Coin Inlet Cover Side Reject Cup Side Plate Reject Cup Base Plate Microswitch Bracket Lockout Flap U.S. 25* Reject Flap Metal Switch Adjuster Black Button Bezel Black Reject Bezel Eniry/Reject Button U.S. 25 Microswitch (Black End Arm) Lampholder 6 V Wedge Base Lamp 91-1108-00

91-1119-00 91-1120-00 91-1122-00

91-1125-00

91-1927-00 91-1141-00

91-1144-00

91-1211-00

91-1212-00 Buttton Spring Lockout Spring Retaining Screw tor Acceptor Body Clear Plastic Cover for Microswitch Plastic Switch Adjuster Base Plate With Pivot and Stud 6 Volt DC Lockout Coil Assembly Zinc Plated Button Bezel Zine Plated Reject Bezel

Page 8

Gold Mech Engineering Data and Parts List

91-3009-00

91-3011-00 91-3022-00

91-3029-00 91-3023-00. \

9 hie

91-3013-00:

91-3006-00———*

Lo ~ 91-3028-00 Zee

91-3002-00

91-3026-00

s-—_ 91-3025-00 ® ES) or-s010-00

‘91-3001-00

~ |” —~91-1036-00

~@=— 90- 1030-00

91-3017-00

91-3008-00

PARTS LIST

90-1030-00 Retaining Screw (#6-32x.250”) 91-3009-00 Gate 91-1036-00 Mounting Stud 91-3011-00 Cradle 91-3001-00 Back Plate 91-3013-00 Magnet Holder with Magnet 91-3002-00 Reject Lever 91-3016-00 Gate Spring 91-3003-00 Reject Lever Spring 91-3017-00 Gate Pin 91-3006-00 Cover Plate 91-3019-00 Separator 91-3008-00 Anti-Stringing Device 91-3022-00 Diameter Adjustment

wa SOIN 1.027 INLET eum

-> MOUNTING STUDS FITTED UPON REQUEST 91-3023-00 Locknut-Magnet Holder 91-3024-00 Screw-Magnet Holder 91-3025-00 Screw Separator 91-3026-00 Washer 91-3028-00 Cotter Pin for Anti-stringing Device 91-3029-00 E-Clip for Cradle

3 HOLES (EACH SIDE) FOR MOUNTING STUDS IF REQUIRED. 6-32 SCREW

Page 9

Gold Mech: Service Information

CLEANING and CARE of the MECHANISM

The magnet that is fitted to the mechanism, should be kept clean from foreign particles. The magnet can be cleaned by swinging the gate open. (as shown in Fig. 1.) Remove metal filings from the magnet by guiding the point of a screwdriver along the edges of the magnet, such that the filings cling to the screwdriver.

The mechanism can be cleaned by immersing in water using a small brush to clean the mechanism. Rinse the mechanism with boiling water and dry with compressed air.

Note: Since the Gold Mech relies on coins passing the magnet at a constant speed, the rejector must be free of dirt and grease which may slow down the coins. Do not lubricate the acceptor with oi! as this slows down coins.

If the above procedures are not successful, check for worn, bent or damaged parts and replace where necessary.

Coin Switch

The coin switch comes in two different spring tensions— identified by the color of the plastic boss at the wire's pivot point.

Red: Light tension—-U.S. 25°

White: Heavy tension—heavy foreign coins Removal of Mechanism

To remove the coin selector: Unscrew the two screws (as SHOWN IN Fig. 2)—swing rear of selector body away from the lock-out side and withdraw.

The Gold Mech Acceptors are designed to require a minimum of maintenance and field adjustment. Coins are checked by diameter and thickness, weight, metal content, bounce, and for ferromagnetic coins such as nickel and steel, a rim test is also used.

The Magnet

Coins that are too thick will fail to pass between the magnet and the backplate of the mechanism; and will be cleared by the magnet wiper when the reject lever is actuated. (Fig. 3)

Page 10

DIAMETER ADJUSTMENT SLOTTED HEX SCREW

ACCEPT PATH OF COIN REJECT

The first check on the coin is at the entry slot which prevents the entry of grossly oversize and bent coins. The next test is at the cradle. When the correct coin falls into the cradle, the cradle tipples and the coin is delivered to the magnet check. Under-diameter coins fall between the legs of the cradle and are returned to reject. Under-weight coins fail to tipple the cradle and.can be returned to reject by pressing the reject lever.

Adjustment

The Gold Mech Acceptors are factory adjusted for optimum performance. If more critical adjustments are desired, or if the unit has been disassembled, the following adjustment procedure is suggested. (Fig. 4)

  • Ensure that the mechanism is in an upright and level position.
  • Loosen the hex locking screw on the magnet holder and unscrew the slotted hex screw.
  • Place a true U.S. 25* coin in the mechansim. Turn the diameter adjustment (Fig. 4) clockwise until the coin falls into the cradle. The cradle should tipple and the coin come to rest on the side of the magnet. Turn the slotted hex screw clockwise until the coin just clears the magnet. Give this screw a further ¥2 turn clockwise for optimum clearance and tighten the locknut. Base Plate Assembly for Coin Doors and Front Plates

-1118-00 100-00

\ on \ bala > er1101 aa

BV-1312-16

Part Number Description 12-4150-01 Gold Mech Acceptor 90-1000-00 Keyhook Bezel Screw 90-1007-00 Flat Head Microswitch Mounting Screw 90-1008-00 Pan Head Microswitch Mounting Screw 90-1016-00 CPJS/Bezel Screw 90-1030-00 Mounting Screw for Gold Mech 90-1032-00 Bezel/Hinge Screw PZ 90-1109-00 Lock Washer for Microswitch Assembly 90-1207-00 Nut for Microswitch Mounting Screw 91-1103-00 Coin Inlet Lamp Side 91-1104-00 Coin Inlet Cover Side 91-1105-00 Reject Cup Side Plate 91-1106-00 Reject Cup Base Plate 91-1107-00 Microswitch Bracket 91-1108-00 Lockout Flap U.S. 25° 91-1109-16 Reject Flap 91-1110-00 Metal Switch Adjuster 91-1113-01 Entry/Reject Button U.S. 25° 91-1116-10 Microswitch (Red End Arm) 91-1117-00 Lampholder 91-1118-00 GV Wedge Base Lamp 91-1120-00 Lockout Spring 91-1121-00 Button Spring 91-1125-00 Clear Plastic Cover for Microswitch 91-1141-00 Base Plate w/Pivot Coit 91-1145-00 12V DC Lockout Coil 91-1311-16 Black Nylon Button Bezel 91-1312-16 Black Nylon Reject Bezel

Page 11

PART #799400

USER INFORMATION

WARNING

F.C.C. REGULATION COMPLIANCE

THIS EQUIPMENT COMPLIES WITH THE REQUIREMENTS IN PART 15 OF FCC RULES FOR A CLASS A COMPUTING DEVICE. OPERATION OF THIS EQUIPMENT IN A RESIDEN- TIAL AREA MAY CAUSE UNACCEPTABLE INTERFERENCE TO RADIO AND TV RECEPTION REQUIRING THE OPERATOR TO TAKE WHATEVER STEPS ARE NECESSARY TO CORRECT THE INTERFERENCE.

“yy KONAMI

815 Mittel Drive, Wood Dale, Illinois 60191 Telephone: (312) 595-1443, Telex: 6871385 KONAM UW, Fax: (312) 595-2973