Street Fighter III
Street Fighter III: New Generation (Europe 970204) (Capcom, 1997) · Manual · 18 pages · 21 sections · original scan
© CAPCOM CO., LTD. 1997 ALL RIGHTS RESERVED © CAPCOM U.S.A. INC. 1997 ALL RIGHTS RESERVED
OPERATORS MANUAL
VN WARNING
This game is for use in the United States of America and Canada. Sales, export or operation outside of these countries may be constructed as copyright and trademark infringements and is strictly prohibited. Violators are subject to severe penalties and will be prosecuted to the full extent of the law.
® COIN-OP, INC. 3311 N. Kennicott Avenue
Arlington Heights, Illinois 60004 PM00186-KIT
Phone: (847) 797-6192 022897 Fax: (847) 797-6306
CAPCOM co-op, nc. STREET FIGHTER THREE™
THANK YOU FOR PURCHASING STREET FIGHTER THREE™ WE INVITE YOU TO USE THE FOLLOWING MAILING ADDRESS, TELEPHONE OR FAX NUMBER FOR PARTS OR SERVICE INFORMATION CONCERNING THIS GAME:
CAPCOM® COIN-OP, INC. ATTN: FIELD SERVICE - VIDEO PRODUCTS 3311 N. KENNICOTT AVENUE ARLINGTON HEIGHTS, ILLINOIS 60004 PHONE: (847) 797-6192 (SERVICE) (847) 797-6320 (PARTS) FAX: (847) 797-6306
THE SERIAL NUMBERS OF YOUR GAME ARE LOCATED AS SHOWN BELOW. PLEASE HAVE THESE SERIAL NUMBERS AVAILABLE WHEN CONTACTING US FOR SERVICE INFORMATION.
PLEASE RECORD THE AAMA SERIAL NUMBER HERE:
- AAMA SERIAL NUMBER:
PLEASE APPLY PRODUCT SERIAL NUMBER STICKER HERE:
CAP@OM* co-op, Inc. STREET FIGHTER THREE™
TABLE OF CONTENTS
Warranty Information ii
Kit Inspection 1
Kit Installation Preparation 2 Installation 2 Marquee 2 Control Panel Components 3 Cabinet Decals 2 Wiring Control Panel 3,10 Test/Volume Bracket 3,7 PC Boards 4,5 CD-DRIVE 4,5
Game Adjustments Test Menu 6 Accessing the Menu 6 How to Select an Item 6 Closing the Menu 6 Menu Item Descriptions 6 Configuration Menu 7 System Configuration 8 Game Configuration 9
Reference Information JAMMA Connections 10 Auxiliary Cable Connections 10
Please read the following instructions to keep the PC boards in good condition:
@ Do not drop or bump the boards. @ Do not spill any liquids on the boards.
DISASSEMBLING THE BOARDS OR REMOVING STICKERS MAY
CAUSE THE TERMINATION OF YOUR REPAIR WARRANTY.
Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC. ‘
CAPCOM’ co-op, ine. STREET FIGHTER THREE™
LIMITED PRODUCT WARRANTY (APPLIES TO DOMESTIC SALES ONLY)
CAPCOM® COIN-OP, INC. (Seller), warrants only to the initial purchaser of its products, that the items listed below are free from defects in material and workmanship under normal use and service for the warranty periods specified:
A. Printed Circuit Boards: Ninety (90) Days B. Electronic and Mechanical Components: Ninety (90) Days
No other part of Seller's products are warranted.
Warranty periods are effective from the initial date of shipment from seller to its authorized distributors.
Seller's sole liability shall be, at its option, to repair or replace products which are returned to Seller during the warranty periods specified, provided:
A. Seller is notified promptly upon discovery by buyer that stated products are defective;
B. Such products are properly packaged and then returned, prepaid to Seller's designated plant.
This warranty does not apply to any parts damaged during shipment or handling, or due to improper installation ‘or usage, or alteration. In no event shall Seller be liable for any anticipated profits, loss of profits, loss of use, incidental or consequential damages or any other losses incurred by the customer in connection with the purchase of aCAPCOM® COIN-OP, INC. product.
WARRANTY DISCLAIMER
EXCEPT AS SPECIFICALLY PROVIDED IN A WRITTEN CONTRACT BETWEEN SELLER AND PURCHASER, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
THIS SHIPMENT HAS BEEN CAREFULLY INSPECTED AND PROPERLY PACKAGED BEFORE LEAVING THE FACTORY. WE CANNOT ASSUME RESPONSIBILITY FOR BREAKAGE THAT MAY OCCUR DURING TRANSPORTATION OF THE GAME. IF THIS GAME IS DAMAGED UPON RECEIPT FROM THE CARRIER, IMMEDIATELY NOTIFY THE CARRIER AND FILE A DAMAGE REPORT.
CAP@OM co-op, inc. STREET FIGHTER THREE™
KIT INSPECTION
CHECK THAT ALL OF THE FOLLOWING PARTS HAVE BEEN SHIPPED WITH YOUR KIT. IF ANY PARTS ARE MISSING, CONTACT YOUR DISTRIBUTOR IMMEDIATELY.
SFNG1000 KIT PARTS LIST
PART NO. DESCRIPTION
SFNG1400 ASSY, PCB, CP3 SYSTEM, STREET FIGHTER THREE SFNG4001 SECURITY CARTRIDGE, STREET FIGHTER THREE SFNG4002 CD-ROM DISK, STREET FIGHTER THREE A-00741 | ASSY, CD-ROM DRIVE C-00322 CABLE, CD-ROM DRIVE DATA, 50-PIN C-00323 CABLE, CD-ROM DRIVE POWER, 4-PIN MT00691 BRACKET, MOUNTING, CD-ROM DRIVE, 1 PIECE TYPE MT00692 BRACKET, MOUNTING, CD-ROM DRIVE, 2 PIECE TYPE $C00101-02 SCREW, 8-32X1/4 PPH SEMS ZC $C00104-05 SCREW, STS #8X5/8 PPH “AB” ZC, FOR WOOD GE1200 MONITOR CARD AW00244 MARQUEE, “STREET FIGHTER THREE” PL00376 PLEX, MARQUEE, CLEAR, 27.0 X 9.0 X 1/8” ‘AW00147 DECAL, CABINET SIDE ‘AW00216 OVERLAY, CONTROL PANEL AW00245-1 DECAL - TOP, GAME PLAY INSTRUCTION, SFNG ‘AW00245-2 DECAL - BOTTOM, GAME PLAY INSTRUCTION, SFNG AW00245-3 DECAL, JOYSTICK & BUTTON SWITCHES, SFNG PM00186 MANUAL, OPERATORS, SFNG 03-0104 HARNESS, STEREO SPEAKER 03-0066 CABLE, AUXILIARY GE2030 JOYSTICK, 8 WAY 16-0130 SWITCH, 1-PLAYER START BUTTON (WHITE 16-0131 SWITCH, 2-PLAYER START BUTTON (WHITE) SWITCH, BUTTON (RED) SWITCH, BUTTON (BLUE) 16-0136 SWITCH, BUTTON (GREE!
Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP. INC. 1
CAPCOM’ co-op, INC,
KIT INSTALLATION
MAKE SURE ELECTRICAL POWER TO THE GAME IS OFF BEFORE STARTING THE KIT INSTALLATION.
PREPARATION
- Disconnect and remove the old printed circuit board(s) from the cabinet.
- Remove or open the control panel, and disconnect and remove the buttons and joystick(s) from the control panel.
- Remove any covering from the control panel overlay, and then remove the control panel overlay.
- Place the drill hole template over the control panel to determine where any new holes should go. Center punch any needed new holes on the control panel.
- Cut out the new holes using a 1-3/16" hole saw.
- If there is an additional control panel cover, figure 1 (such as plastic or lexan) that will be utilized, cut any additional holes using the same template. *cover is not included in the kit.
- Plug up unused holes with a wood dowel (1-1/8" diameter) and sand any rough edges.
INSTALLATION
Marquee Installation
- Remove the marquee plexi glass, marquee overlay, and the cabinet graphics.
- — Install the new marquee and replace the plexi glass. Clear plexi glass is included in “full” kit.
Control Panel Overlay Installation (See Figure 1)
+10. The control panel overlay in the kit is oversized to accommodate most control panel sizes. Center the overlay on the control panel, leaving some excess material at the edges.
- Remove the protective backing from the overlay and press it down on the control panel, keeping it properly aligned. Press it down firmly, smooth out any bubbles, and press it over the edges.
- Trim any excess from the overlay. Place the drill hole template on top of the overlay, aligning it with the joystick holes. Pierce through the overlay at each control panel hole. Then, cut away overlay material covering the joystick and button holes. Remove the template and clean off the overlay.
iN) Proprietary and confide STREET FIGHTER THREE™
- Peel off the backings of the 6-button and joystick decals, align over the control panel holes, and press in place on the overlay (refer to the drill hole template for proper placement). Using a knife, trim material from the center hole of the joystick decal.
- Install the control panel cover, figure. 1. (if required).
Overlay (Trim to size)
Figure 1: Overlay Installation
CABINET DECAL INSTALLATION
- Remove monitor glass and install monitor card
- Peel-off the backing to the instruction decals and place on both the top and bottom of the monitor card. (See Figure 5). Also, apply the cabinet decals to both sides of the cabinet.
MARQUEE OVERLAY MONITOR CARD CABINET DECAL INSTRUCTION DECAL - BOTTOM
INSTRUCTION DECAL - TOP
(CARCOMY COIN-OP, INC.
Reassembly of Components
- Notice that there are two white buttons. See figure 2. The WHITE buttons are START buttons. Install the PLAYER ONE button on the top left-hand side of the control panel, and the player two button on the top right-side of the control panel. 1 Player OQ © ye - Figure 2: Start Buttons Red Green Blue Red Green Blue
pe 7 2 Player
Red Green Blue Red Green Blue
Buttons —_
Retaining Rings
Switches —~
Figure 3: Control Panel Buttons and Switches
- Install all buttons and retaining rings on the control panel as shown in Figure 3. Install two red buttons to the immediate right of each joystick, install two green buttons to the right of the red ones, and install two blue buttons to the right of the green ones.
- Install the switches on the buttons as shown in figure 3. Orient the switches so that when a button is pressed, the plastic contact on the switch is depressed.
- Install the joysticks on the control panel as shown in figure 4.
Figure 4: Joystick Installation
PC BOARD INSTALLATION
Proprietary and confi 3 to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC. STREET FIGHTER THREE™
CONTROL PANEL WIRING
- Reconnect the existing jamma connectors to the control panel according to the chart in table 1.
- Connect the player 1 and the player 2 kick buttons to the auxiliary cable harness as shown in figure 6. Make the connections according to the chart in table 2. To PC Board Connector cna
Figure 6: Auxiliary Cable Harness
TEST SWITCH WIRING
- Your cabinet may already equipped test switch. An optional test/volume bracket (see Figure 7) is available through your local CAPCOM distributor (part number 03- 0050). When installing, the test switch bracket should be mounted inside the coin door and on top of the cash box for easy access. (See Page 7 for wiring detail)
Figure 7: Test/Volume Bracket
- If you are converting a cabinet that is equipped with CAPCOM® Q-SOUND, you may use stereo audio output connect to existing Q-SOUND POWER AMPLIFIER.
we
(CARCOMY COIN-OP, INC.
- Install the caged PCB to the control panel shelf with supplied wood screws, as shown in figure 8.
Figure 8: PC Board Mounting STREET FIGHTER THREE™
CD DRIVE INSTALLATION
- Install the CD-DRIVE in place you can access easily. Horizontal placement is recommended for stable operation. (See figure 9).
USE ONLY supplied “Pam Head Screw” to mount CD- DRIVE.
MISUSE of screw may cause mechanical damage to the unit. Make sure CD-DRIVE mounted horizontally and leveled.
PPH 8-32x1/4 Qty. 8 Total
Self Tapping Screw Qty. 4 Total
Picture shown only Right side Bracket & Screws.
Figure 9: CD-DRIVE Mounting
PC BOARD WIRING CONNECTIONS
JN WARNING
Improper installation of the connector haness (JAMMA / CD-DRIVE / AUX) to the PC board connector may cause damage to the PC board and CD-DRIVE.
- Attach Power and Data Cable to CD-Drive. Connect other end to SCSI combination connector on the -main PCB (Figure 11).
- Connect the JAMMA harness connector to the edge connector on the PC Board (Figure 11).
- Attach the auxiliary cable connector to the PC Board. (Figure 11).
- Ifyou elect to use Q Sound Audio Amplifier, connect audio cable to audio output on the PC Board. (Figure 11). Carefully check connections before applying power.
Check the Cassette seating , press firmly from top and confirm it is not loose.
- Power-up the game and set the CD-ROM into CD- Drive. (See Figure 12. For detail)
CD-Tray Door will not operate without power.
Game will not work without the CD-ROM installed.
- After set the CD-ROM, the game is playable. Adjust the speaker volume by turning the volume control knob clockwise to increase volume, or counterclockwise to decrease volume (see Reference page).
34, Set all operator adjustable options by pressing the TEST switch. Follow the instructions under the TEST MENU section of this manual.
4 [Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.
CAPGOH cow.op, inc. STREET FIGHTER THREE™
To Audio Power Amp,
To Power Supply, Control Panel Coin Door, Monitor, Test Switch and Speaker (Monaural).
Figure 11: PC Board and CD-Drive cable connection
CD-ROM INSTALLATION 35. Press Open/Close button to open the CD-Tray.
- Set the CD-ROM. Secure the CD-ROM withi Disc Locks. (See Figure 12). Move four Disc Locks toward center to secure CD-ROM.
Make sure it is centered and locked in place.
- Close the CD-Tray by pressing Open/Close button.
- After loading CD-ROM, the game is ready to play.
CAUTION
Do not remove the CD-ROM from the Drive during the game. It could result in break down. OPEN/CLOSE Button
Figure 12: CD-ROM Installation
Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.
CAP@ONT’ co-op, ine. STREET FIGHTER THREE™
TEST MENU
The test menu allows you to test various functions of the game and configure settings used in the game. These items include input devices such as joysticks, buttons and coin mechs, output devices such as monitor, speakers and meters. Through the test menu you can also access the configuration menu, where you can change the settings of the game.
TEST
« INPUT . OUT! PUT . SOUND & VOICE . COLOR . DOT CROSS HATCH . GAME DATA
- CONFIGURATION .
- ACCESSING THE TEST MENU
MENU
- For a CAPCOM® cabinet or a converted cabinet with a test switch: Make sure the game is on. Open the coin door, find the location of the test switch, and press “Test”. The screen shown left will appear on the monitor:
For a cabinet without a test switch: . MEMORY CHECK . GAME REWRITE
- EXIT
SELECT = START =
Player 1 Joystick 1P UP OR DOWN 1P START & SHOT1
Player 1 Start Push “Test switch” on the PC Board. (See Reference page ).
- HOW TO SELECT AN ITEM
- Use the PLAYER | JOYSTICK to move the arrow in front of the desired item and press the PLAYER 1 PUNCH LIGHT button.
- to return to the test menu, push the PLAYER / START
Player 1 Shot 1 (Punch Light) Player 1 Shot 2 (Punch Middle), and PLAYER 2 START buttons simultaneously.
- Closing the test menu To close the test menu, highlight “9. Exit” and push the PLAYER 1 PUNCH LIGHT button. visor
. The test menu will always appear on the screen: A) after you exit the “7. CONFIGURATION MENU” and B) after the memory is tested from the menu, “8. MEMORY CHECK”.
- TEST MENU ITEM DESCRIPTIONS
INPUT USED TO TEST ALL THE INPUT SWITCHES, SUCH AS JOYSTICKS AND BUTTONS. THE “0” CHANGES TO A “1” AS THE BUTTON IS PUSHED OR JOYSTICK IS MOVED. CHECK CONNECTIONS AND SWITCHES IN CASE THE “0” DOESN'T CHANGE TO A “1” WHEN DEPRESSED OR MOVED. OUTPUT USED TO TEST THE COIN METER AND THE COIN LOCK. SOUND SELECT A CODE OF SOUND OR VOICE WITH THE PLAYER I JOYSTICK. PUSH THE PLAYER | PUNCH LIGHT BUTTON TO HEAR THE SOUND OF THE SELECTED CODE. COLOR SHOWS COLOR BARS OF RED, GREEN, BLUE, AND WHITE. ADJUST RGB AND BRIGHTNESS TO OBTAIN THE OPTIMUM COLOR BALANCE AND SOLID BLACK BACKGROUND. DOT CROSS HATCH USED TO TEST THE SCREEN SIZE, FOCUS AND DISTORTION. GAME DATA COIN METER AND PLAYTIME INFORMATION WILL BE DISPLAYED. CONFIGURATION USED TO CHANGE THE GAME PLAY SETTINGS. REFER TO THE CONFIGURATION MENU SECTION. MEMORY CHECK USED TO TEST MEMORY. “OK” APPARS WHEN EACH BLOCK OF MEMORY PASSES TEST, “NG” APPEARS IN CASE OF MALFUNCTION. IF “NG” APPEARS, REPEAT THE MEMORY TEST AND WAIT FOR THE “OK” MESSAGE. CONTACT YOUR DISTRIBUTOR IF “NG” STILL APPEARS. GAME REWRITE IN CASE THE GAME IS NOT FUNCTIONAL PROPERLY, REWRITE THE DATA TO THE MOTHER BOARD. IF YOU SHOULD CONTINUE TO HAVE PROBLEMS REWRITING THE PROGRAM, CONTACT YOUR DISTRIBUTOR. *WARNING : THIS FUNCTION WILL TAKE 20 MINUTE. *NEVER TURN THE POWER OFF DURING THE PROCESS. EXIT SELECT THIS ITEM AND PUSH THE PLAYER 1 PUNCH LIGHT BUTTON TO RETURN TO GAME PLAY MODE.
6 Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.
CAP@OM’ co-op, inc. STREET FIGHTER THREE™
CONFIGURATION MENU
The configuration menu is used to change various game settings such as level difficulty, credits, sound configuration, etc. These settings are stored in memory on the PCB rather than DIP switches. The configuration menu is divided into 2 sections. In the SYSTEM section, you can change credits, sound, and coin door configurations. In the GAME section, you can change the play difficulty level and duration of the game.
1, ACCESSING THE CONFIGURATION
- CONFIGURATION MENU MENU
. SYSTEM . From the TEST MENU, move the arrow to “7. . GAME CONFIGURATION” and push the PLAYER | PUNCH
. DEFAULT LIGHT button. The screen below will be displayed. A description of each option is explained in the table below.
. SAVE & EXIT
SELECT START = 1P UP OR DOWN =1P START & SHOT1
| SYSTEM SELECT THIS ITEM TO CHANGE SETTINGS FOR CREDITS, MONITOR FLIP, SOUND AND COIN DOOR CONFIGURATIONS. GAME SELECT THIS ITEM TO CHANGE DIFFICULTY LEVEL, DAMAGE LEVEL, TIME COUNT SPEED, MAXIMUM NUMBER OF ROUNDS AND EVENT TYPE. DEFAULT USE THIS ITEM TO RESTORE CONFIGURATION SETTINGS TO THE ORIGINAL FACTORY VALUES. PRESS THE PLAYER | START AND PLAYER 1 PUNCH LIGHT BUTTONS AT THE SAME TIME TO SELECT THIS OPTION. SAVE & EXIT
AX Cy USE THIS TO SAVE NEW CONFIGURATION SETTINGS AND EXIT TO THE TEST MENU. THE MESSAGE “SAVING NEW CONFIGURATION IN EEPROM” WILL APPEAR WHILE THE NEW SETTINGS ARE BEING SAVED. . DO NOT TURN POWER OFF TO THE GAME UNTIL “SAVING” IS COMPLETE AND THE TEST MENU REAPPEARS.
Wiring of the test bracket requires connections to the main jamma harness as shown in Table 1:
LEAD WIRE COLOR SWITCH FUNCTION CONNECTS TO
YELLOW VOLUME-UP NO CONNECTION BLACK VOLUME-DOWN [NO CONNECTION GREEN COMMON NO CONNECTION. BROWN
[Proprietary and c TEST JAMMA “15” JAMMA “A” OR “B” OR “E” OR “F” OR “1” OR “2” OR “27” OR “28”
Table 1: Test/Volume Bracket Wiring Chart
information, not to be disclosed or copi ut the express permission of CAPCO!
CAPCOM’ cow.op, inc. STREET FIGHTER THREE™
SYSTEM CONFIGURATION
CHANGING THE SYSTEM CONFIGURATION 7-1. SYSTEM CONFIGURATION SETTINGS
>4. COIN MODE 2 COINS 1CREDIT . CHUTE TYPE 2 CHUTES SINGLE
OO NUE ON Move the PLAYER I JOYSTICK up or down to highlight the
. DEMO SOUND desired option. Once the option is highlighted, move the . SOUND MODE PLAYER I JOYSTICK \eft or right or press the PLAYER | Hex PUNCH LIGHT button to select.
SELECT OPTION =1P UP OR DOWN MODIFY SETTING =1P LEFT OR RIGHT =1P SHOT1 OR SHOT2
SYSTEM CONFIGURATION ITEM DESCRIPTIONS
1, COIN MODE SELECT THE CHARGE PER PLAY.
- CHUTE TYPE SELECT THE NUMBER OF PLAYER(S) AND COIN CHUTES. 1 CHUTE SINGLE: WITH THIS SETTING, EITHER PLAYER CAN START THE GAME. 2 CHUTES SINGLE: TWO PLAYERS USE ONE COIN CHUTE AND PLAY AT THE SAME TIME. THE PLAYER WHOSE COIN WAS PUT IN FIRST STARTS THE GAME. 2 CHUTES MULTI: TWO PLAYERS USE TWO COIN CHUTES AND PLAY SEPARATELY. THE GAME STARTS FROM THE SAME SIDE AS THE COIN CHUTE WAS USED.
- CONTINUE USED TO SET THE CONTINUOUS PLAY.
- MONITOR USED TO FLIP SCREEN. IF SCREEN APPEARS UPSIDE DOWN, CHANGE THE SETTING.
- DEMO SOUND TURNS ATTRACT SOUNDS ON OR OFF.
- SOUND MODE SELECT STEREO OR MONAURAL FOR USE WITH YOUR CABINET. . NOTE: STEREO SHOULD ONLY BE SELECTED FOR USE WITH CAPCOM® QSOUND CABINETS OR THE CABINET EQUIPPED STEREO POWER AMPLIFIER. TO SAVE THE SETTINGS AND RETURN TO THE CONFIGURATION MENU, HIGHLIGHT THIS ITEM AND PUSH THE PLAYER | START BUTTON
SYSTEM CONFIGURATION OPTION SETTINGS
| 1. COIN | 1COIN | 1 COIN | 1 COIN | 1 COIN | 1 COIN |
| 1 CREDIT | 2 CREDITS | 3 CREDITS | 4 CREDITS | 5 CREDITS | |
| 1 COIN | 1 COIN | 1 COIN | 1 COIN | ||
| 6 CREDITS | 7 CREDITS | 8 CREDITS | 9 CREDITS | ||
| 3 COINS | 4 COINS | 5 COINS. | 6 COINS | 7 COINS | |
| 1 CREDIT | 1 CREDIT | 1 CREDIT | 1 CREDIT | 1 CREDIT | |
| 8 COINS | 9 COINS. | 2 COINS START | FREE PLAY | ||
| 1 CREDIT | 1 CREDIT | 1 COIN CONTINUE |
- CHUTE TYPE 1 CHUTE SINGLE 2 CHUTES SINGLE 2 CHUTE MULTI
- CONTINUE
Ni 4, MONITOR
- DEMO SOUND
- SOUND MODE
8 Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.
CAPCOLI coin-op, inc. STREET FIGHTER THREE ™
GAME CONFIGURATION
CHANGING THE GAME CONFIGURATION
7-2. GAME CONFIGURATION SETTINGS
| > 1. GAME DIFFICULTY | EASY [.. | .] HARD | |
| 2. DAMAGE LEVEL | Low [.: | .] HIGH | |
| 3. TIMER COUNT SPEED | Penn | a | Move the PLAYER | JOYSTICK up or down to highlight the |
| 4. MAX ROUND | 3 ROUNDS | desired option. Once the option is highlighted, move the | |
| 5. EVENT | OFF | PLAYER I JOYSTICK left or right or press the PLAYER | |
- EXIT PUNCH LIGHT button to select.
SELECT OPTION
MODIFY SETTINGS
= 1P UP OR DOWN =1PLEFTORRIGHT =1PSHOT1 ORSHOT2
GAME CONFIGURATION ITEM DESCRIPTIONS
1, DIFFICULTY SETS THE DIFFICULTY LEVEL.
- DAMAGE LEVEL SETS THE OFFENSIVE POWER LEVEL
- TIMERCOUNT SETS THE SPEED OF THE COUNTDOWN.
- MAX ROUND SETS THE NUMBER OF ROUNDS PER MATCH FOR “VS. CPU”: 1 ROUND: WINNER OF A SINGLE ROUND WINS; 3 ROUNDS: WINNER OF 2 OUT OF 3 ROUNDS WINS; 5S ROUNDS: WINNER OF 3 OUT OF 5 ROUNDS WINS.
- EVENT TURNS ON EVENT MODE. USEFUL FOR CHAMPIONSHIP TOURNAMENT. OFF: NORMAL SETTING. SETS THE MODE TO NORMAL OPERATION. ON: MATCHES PLAYER WITH ONE CREDIT. A WIN OR A LOSS RESULTS IN GAME OVER. (CONTINUE IS NOT AVAILABLE). RETURN TO THE CONFIGURATION MENU.
GAME CONFIGURATION OPTIONS
- DIFFICULTY HARD
- DAMAGE LEVEL HIGH
- TIME COUNT
- EVENT
Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC, 9
CAP@OM co-op, inc. STREET FIGHTER THREE™
*WIRE COLOR SOLDER SIDE COMPONENT SIDE *WIRE COLOR
N
N.C.
+12 VDC
KE
COIN COUNTER 1
COIN LOCK 1
*SPEAKER (+)
N.C.
VIDEO RED
VIDEO BLUE
VIDEO GROUND
TEST MODE
1 PLAYER - COIN
1 PLAYER - START
1 PLAYER - UP
1 PLAYER - DOWN
1 PLAYER - LEFT
1 PLAYER - RIGHT
1 PLAYER - PUNCH LIGHT
1 PLAYER - PUNCH MIDDLE
1 PLAYER - PUNCH HEAVY
NIC
NIC
GND COIN LOCK 2 [ —_Fsreaxer 6
VIDEO SYNC
SERVICE (FREE CREDIT) NIC
2 PLAYER - COIN
2 PLAYER - START
VIOLET/BLACK 2 PLAYER - UP
2 PLAYER - DOWN
2 FLAYER -LEFT
2 PLAYER - RIGHT
2 PLAYER - PUNCH LIGHT
2 PLAYER - PUNCH HEAVY
LT WHITE/BLACK
WHITE/BROWN
WHITE/RED
WHITE/ORANGE
WHITE/YELLOW
WHITE/GREEN
WHITE/BLUE MO ae TE NK KE MC OBA VZSZO RACE IM ONS
Table 2: JAMMA Wiring Connections
- Wire Color Note: Wire colors shown are according to the AAMA-AMOA Standard for wire color assignments; your harness may contain different colors than shown above.
CONNECTOR EVEN ROW WIRE COLOR
NIC
NIC
NIC PURPLE/YELLOW PLAYER 2 KICK HEAVY
NIC
NIC
PLAYER | KICK HEAVY PLAYER 1 KICK MIDDLE
PLAYER 1 KICK LIGHT GRAY/YELLOW PLAYER 2 KICK LIGHT PINK/YELLOW ny a PLAYER 2 KICK MIDDLE NIC NIC NIC oh N/C NIC qv GRAY/YELLOW NO CONNECTION NO CONNECTION PINK/YELLOW
BLACK/WHITE NO CONNECTION NIC BLACK Ww i}
a PLAYER 2 COMMON
Table 3: Auxiliary Cable Wiring Connections PLAYER | COMMON BLACK
Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC,
1-3/16" DRILL FOR 1P OR 2P START BUTTON SWITCH
1-3/4" DRILL FOR JOYSTICK HOLE
1-3/16" DRILL FOR BUTTON SWITCH HOLES
CAPCOM Con-cP, INC. 3011 NORTH KENMICOTT AVENUE ‘ARLINGTON HEGHTS, ILLINOIS 60004 PHONE (708) 797-6100 COIN-oP, ING. FAX (10a) 737-5119
DRILL HOLE TEMPLATE: STREET FIGHTER THREE™ DATE | ‘DRAWN BY: | eV.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
CAPGOL" co-op, inc. STREET FIGHTER THREE™
REFERENCE INFORMATION
PC BOARD CONNECTIONS AND CONTROLS
Volume Control Knob
Stereo Audio
Connector Cartridge
JAMMA Harness Test Switch mo Auxiliary Cable
TYPICAL CONTROL PANEL LAYOUT OF STREET FIGHTER THREE ™
ete woe eR @e@@ @e@e@ four wcfune sree
1600200
NOTICE
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.
WARNING
Federal law provides severe civil and criminal penalties for the unauthorized reproduction, distribution, or exhibition of copyrighted audiovisual works and video games.
The Federal Bureau of Investigation investigates allegations of criminal copyright infringement.
CARCOMS COIN-OP, INC. 3311 N. Kennicott Avenue
Arlington Heights, Illinois 60004
Phone: (847) 797-6192 Fax: (847) 797-6306
Copyright © 1997 CAPCOM ® coin-op, Inc., All Rights Reserved