CATHODE RAY TOMES

Dark Planet

Dark Planet (Stern Electronics, 1982) · Manual · 14 pages · 13 sections · original scan

Page 1

Be _.. OPERATION

TERN gees"

Page 2

The object of the game is to get all three bases burning at once, and keep them burning.

When the game first starts you will see two fighters and trak laying jeeps appearing from a bunker below you. Destroy fighters and jeeps from above by using the laser button (which destroys everything below it). The trak-laying jeeps are trying to build &@ loop of trak so the laser train (which destroys everything above it), has maximum mobility.

When the laser train appears, a protective fighter appears with it. You must destroy this fighter with your laser from above, before dropping down to the lower level to battle with the laser train. After destroying all the jeeps and the-laser train on a loop you can then attack the bunker on that loop and set it on fire. . :

To move back and forth between levels you must go up or down the transport tube.

Occasionally fighters will come up the transport tube to the upper level to attack you if you stay on the upper level too long without dropping down to the lower level. Also, two enemy guns located in the cliffs of the upper level start to shoot 4f you stay on the upper level too long.

Randomly the volcano will start to erupt and start to cover the screen in blue. You must shoot the volcano with your missles to stop the eruption. (You must be on the upper level to shoot the volcano). If the eruption covers the screen, you will be destroyed.

When attackers are below you, use the laser button to destroy them. When attackers are on the same level as your ship, use the missle button to destroy then.

Laser train has no defenses on lower level, but will destroy everything above it.

Each loop is worth 24,200 points each.

Each loop contains:

12 - jeeps worth 100 points each. 3 - fighters worth 1,000 points each. 1 - laser train woth 10,000 points each. 1 - bunker worth 10,000 points each. 50,000 point bonus if you have all three bunkers on fire at the same time.

Page 3

MIRROR MAINTENANCE REFER TO ILLUSTRATIONS FOR MIRROR IDENTIFICATION

Mirror and color filters should be dusted periodically to prevent dust and dirt build-up on the mirrors and filters, which will affect their performance.

A soft cotton rag or a camel hair brush should be used to dust the mirrors and filters periodically. .

If a mirror or filter needs cleaning, only a silicon based cleaner with a spray head, such as STERN ELECTRONICS MIRROR CLEANER (part #264-36) should be used. Wo alkaline, acidic, or ammonia type cleaners (such as Windex (TM) or Fantastic (TM)) should be used. Only a soft cheesecloth or cotton rag should be used to clean the mirrors or filters.

CAUTION: At no time should anything abrasive be used on the mirrors or color filters.
Page 4

, VIEWING MODULE

  • 6-32 x 5/16 SEMS Ti6 REQD.)

FLUORESCENT

PC-B-2316

VIEWING MODULE

SIDE ASSEMBLY

RIGHT. SIDE : C-2327 LEFT SIDE: C-2328 TAPE (WNA-I38) BLACK BAFFLE ASSY.

BLACK BAFFLE

BLUE FILTER ASSY. ora ag

28-371

(2 PER SIDE) MIRROR ASSEMBLY

C-233! MIRROR : 15B-50-2 MOUNTING SCREW 1/4-20x1I"LG.

RED FILTER ASSY. MIRROR 15B-50-1 LOCKWASHER 3A-143-25 (4 OF EACH REQD.)

Page 5

(78-5i-1) VIEWING MODULE 1 esses ASSEMBLY 2828) aSseMel Lowe! "AN ASSEMBLY fece : Te, BRACKET be Ga-77-4)

PLANET a FLUORESCENT IGHT SOCKET

REFLECTOR (130-7 INET LIGHT BOARD ASS'

LAMP ASSEMBLY. (ea-423) 7 OW INCANDESANT CONTROL PANEL APPLIANCE GRADE BULB ASSEMBLY APPLIAN

peal ANET LIGHT SHIELD

PLANET BAFFLE. Usc-49) PLANET @ MIRROR ASSY (A-2324)

ENCODER (88-414) con REAR DOOR (A-232!) (0-705-3) Tiarree | cation) COUNTER (a-2343) poor guscunones FRONT Poor bAestelsy st UNE FLIER

‘CASH BOX & CASH BOX COVER 90-297) (c-263) COIN MECH (98-230)

Page 6

ah sa (28-485 _ IMPORTANT:

REPLACE WITH 40 WATT

APPLIANCE BULBS ONLY. (GE"40AI5-22) : (SYLVANIA™ 40A15)

CLEAN YELLOW GLASS

PERIODICALLY.

MIRRORS IN OPTICS MODULE ARE 1ST SURFACE, I.E. HAVE COATINGS ON THE

SURFACE OF THE GLASS. _

CLEAN WITH A SOFT COTTON

RAG AND DON'T. SCRATCH.

NOTE: USE ONLY A DRY RAG, (NO GLASS CLEANER) FOR THE LARGE MONITOR MIRROR.
Page 7

"8-32x1" CARRIAGE BOLT a (4REOD) T PUSH BUTTON A-7II-(SPECIF Y COLOR) 10-24% 1/4" CARRIAGE BOLT 318-352 SCREENED ——-PLASTIC PANEL 130-77

CONTACT SWITC! SW-477-5 (6 REQO.) WOOD CONTROL PANEL 230-140

FLAT WASHER 3A-109 ; KEPS HEX NUTS 10x3/4 S.M.SCREW

1 7 | B..-——— 31A- 888 nt 8 (4 RED.)

ENCODER SWITCH 8B-414 *(WITH WASHER & NUT) all a HOLD-DOWN BRACKET : L- § 170-155

Page 8

2.

4.

5.

6. COLOR MONITOR SETUP_INSTRUCTIONS 69x1179-100

one one

wago1 xhg952 (O86 W SYNC wee : 43902 wh956 =~ CO sctne eve use 4906 KU95ER pos» smc | wonizowras src Kugit Ku961

WOR VERT VERT VERT «WERT WORIZ SCREEN CENTERING SIZE HOLD DAMPING RASTER RASTER emet suirT

HORIZONTAL FREQUENCY

With the monitor betng driven from the game signal, connect a Jumper between TP601 and TP31. Adjust the horizontal hold control until picture stops sliding horizontally, remove Jumper. Do not use the horizontal hold contro! for hortzontal centering. (See #3) NOTE: When game sync Is composite, use horizontal sync Input.

PICTURE SIZE

Adjust the vertical size control, and the horizontal width coil for desired picture size.

PICTURE CENTERING

If the video Is off center vertically, move the vert raster position adjustment to the up or down position. If the video Is off center horizontally, adjust the horizontal video position control to center the picture. If any additional horizontal positioning Is required, move horizontal raster position adjustment to the left or right position. .

VERTICAL DAMPING

Adjustment of this control fs required only If the monitor ts being used with @ game In which the top several raster lines are visible on the scréen. Adjust the vertical damping control for uniform spacing of the top raster lines.

BLACK LEVEL

Adjust the black level control to obtain the proper black level (the black portion of the picture Just extinguished). Do not use the screen control to set the black level.

Focus Adjust the focus control for best overall definition and fine picture detail.

Page 9

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 10

M3177 +5V.D.C. REGULATOR

-5V.D.C. REGULATOR 7905C

CONNECTION TO SV.D.C. POWER TRANSISTOR +12V.D.C. = REGULATOR lal F2 F3 7812 4 AMP_2AMP 1 AMP

POWER OUT BRIDGE RECTIFIER CRI

KBPC 6005

TRANSFORMER

FIGURE 4. POWER SUPPLY BOARD PS-1200

Page 11

EDGE CONNECTOR

Page 12

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 13

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 14

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.