CATHODE RAY TOMES

TacScan

Tac/Scan (Sega, 1982) · Manual · 154 pages · 20 sections · original scan

Page 1

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 2

Heat

Owner’s Manual

Manufactured By

TLX 910-335-1621

TACISCAN OWNER’S MANUAL Copyright © 1982 by SEGA/Gremlin, All Rights Reserved

Page 3

TABLE OF CONTENTS

Introduction. 2... ee ee ee ee eee ee ew A Game Concept . 2. 6 eee eee ee ee ee ee 2

Scoring 2 ee ee ee ee ee ee ee

Game Set-Up and Inspection. . 1... 6. ee ee ee ee

Specifications and important Notes. .........6

Option Selection. ©... eee ee ee ee ee ee eB

Self-Test 2... eee eee ene ee ee eee TM G-80 Bus Details... ee ee ee ee IS

Troubleshooting Procedures... ......242. 16

Circuit Desription. .. 2... 2.2... ee ee eee 20

Monitor Block Diagram 2... ee ee ew eee ee 25

Adjustments and Specifications. .......... 36

Parts Catalog «1 6 wee ee ee ee ee eee ee AD

Schematics 2. 6 eee ee ee ee ee ee ew TTA

Page 4

INTRODUCTION

TAC/SCAN is a microprocessor based coin-operated electronic game, that makes extensive use of digital integrated circuitry and television monitor concepts. This manual is designed for the use of the maintenance technicians who possess a general working knowledge of solid-state circuitry and video monitor theory. Any individual NOT knowledgeable in these areas SHOULD NOT attempt repair of the electronic portions of the game.

In addition to this manual and training in electronics, troubleshooting and repair will be facilitated by: access to general electronic type handtools, a multimeter, a 50 to 100 Mhz oscilloscope and a logic probe would be helpful.

Technical assistance is available by calling (800) 854-1938, or (800) 722-8576 inside CA. Questions or comments concerning TAC/SCAN or any of our games are welcome and should be directed to:

Customer Service Manager SEGA/Gremlin 16250 Technology Drive San Diego, California 97127

Page 5

GAMF CONCFPT

TAC/SCAN is a one or two player alternate action game, displayed via SEGA's Color X-Y video system. Commanding unprecedented firepower, the player maneuvers seven fighter ships in a squadron formation. Al) seven ships fire al once when the FIRE button Is pressed, producing a spectacular missile salvo. The object of the game is ta accumulate points by destroying incoming enemy ships while dodging fireballs launched by these enemies. TAC/SCAN presents the space battle from two entirely different perspective views in the course of the game, with visually exciting transition sequences interconnecting the two views. The player begins the game with a seven ship formation, and a supply of reserve ships which are shown above the player score on the screen. The number of reserve ships at the beginning of the game are switch selectable. An ADD SHIP button placed next to the FIRE button transfers one of the reserve ships in the squadron furmatton, Where the reserve ships are placed is shown by a half-intensity fighter in the formation. This "add ship" position continuously cycles between the empty squadron positions, and the advanced player will time the ADD SHIP function to place squadron fighters at preferred positions. A player fighter is blown up by contact with either an enemy ship or an enemy fireball. Whenever all seven ship positions become empty the game is over, EVEN IF THERE ARE REMAINING RESERVE FIGHTERS shown above the

player score, Thus the player must continuously judge when to add reserve tighters by using the ADD SHIP button, Add them too early, and they might be depleted too fast; use them too late and you risk ending the game with reserve fighters left over. There is an additional way to add ships to the squadron. During the course of the action, player fighter ships enter the playfield and intermix with the enemy ships. The player can capture these fighters directly into the seven ship formation by steering them into empty fighter positions. The player's missile fire DOES NOT blow up friendly fighters--only enemy ships. TAC/SCAN begins with a top view of the battle. For the first ten seconds the player shoots at enemy ships without having to worry about return tire. After this ‘'warm-up" period, game play escalates dramatically. During this first phase, a different type of enemy appears just after

Page 6

two of the player fiahters fly onto the screen. This is the Stinger, which flits around the field and shoots a deadly laser. This ship is a highpriority target, since if not dealt with, it will pick off all of the squadron ships and end the game. When the player attempts to dock a friendly fighter into the squadron formation, he or she has the choice of any of the empty ship positions shown in the squadron. A special feature occurs when the player ship docks into the frontmost ship postition (marked with a red “cursur'). This causes the squadron formation to regroup into a different pattern. If

the lead pogition is occupied, a Fighter fe added to the reserve caunt ahnve

the player's score. At the end of the first phase (the top view) the squadron ships regroup, and a dramatic transition sequence takes the player into phase two. This sequence consists of the fighters rising and enlarging in size, then turning INTO the screen, lighting afterburners, and proceeding to fly forward to continue the battle. The enemy ships now appear far off in the distance, and grow in size as they approach the player's squadron. The player is given chances to rendezvous with friendly fighters, as in phase

one. At the end of this second phase, a space tunnel appears on the sereen, and the playcr uses the rotary control to steer the sqitadron formation through the tunnel. Any fighter which hits a side walt of the tunnel explodes on contact. A triangular guide is shown during this sequence to show the player where his triangular ship formation should be. If the player keeps the formation centered within the guide, no ships will

be lost. Once out of the space tunnel, the player resumes with the second round, This is a more difficult top view battle, as at the beginning ot the game. TAC/SCAN proceeds with multiple two phase rounds {phase one is the top view, phase two 1s the rear view) untt) all squadron ships arc

lost. A switch option allows bonus reserve ships to he added with certain score values. The factory set option is to add one reserve ship every

30,000 points. Regardless of the number of squadron ships on the screen, there are always seven misssiles at a time available to the player. If there are seven ships on the screen (a full squadron), pressing the FIRE button launches al? seven at once. Another push of the FIRE button cancels the

Page 7

seven in flight and launches seven new ones. If the squadron is not full, the seven missiles can be independently targeted. For example, with a single ship, seven missiles can be fired in seven directions, and only when the efghth Is shot Is the first one terminated (if it is still on the screen). The two player game is played with players alternating after

successful negotiation of the space tunnel. Whenever a player is eliminated, the other player continues and finishes the game.

SCORING

Enemy Ships Stinger

Round |100 points1000 points
Round 22002000
Round 33003000
Round 44004000
Round 55005000
Round 66006000
Round 77007000
Round 8 and above8008000

Destroying two enemy ships with a single missile satvo doubles the point values shown.

Destroying three enemy ships with a single missile salvo triples the point values shown.

Page 8

GAME SET-UP AND INSPECTION

  • Inspection
  • Before plugging in your new game, inspect it closely to spot any possible shipping damage. Check to ensure the graphics are in place, the monitor is not damaged and that the overall cabinet is in good condition.
  • Open the coin mechanism door and inspect the inside of the game electronics compartment. Be sure no components or connectors have come loose. Proper connector fittings must be checked before game power is applied. Check all related connectors for good contact. Although disconnected connectors are easily spotted, poor contacts are difficult to locate. The connectors should therefore be pushed in firmly and then loosened to spot poor connections.
  • Check to ensure the fuses are intact. There are five fuses (not counting the monitor fuses which are detailed in the monitor manual for this game). One fuse is located on the AC junction box. The other four are on the power supply PC boara.
  • Voltage Selection

Before plugging in your game, make sure that the game voltage is correct for your location. Locate the two leads from the AC junction box to the power transformer. For 110 VAC, they should be connected to terminals 1 and 3 on the power transformer. For 100 VAC, connect 1 and 2, and for 220 VAC applications, they should be connected to 1 and 4. You will also notice on the AC junction box that there is a safety interlock switch. When the front panel is in place the switch is depressed and the game receives power. Removing tne front panel, the switch returns to its original position and the power is cut off from the game. For servicing, this switch can be pulled out and power will be restored.

  • Game Specifications

Power 100 VAC, 60HZ (nominal), 150 watts maximum

Page 9
  • Game Specifications (Cont)

Power 110 VAC, 60HZ (nominal), 150 watts maximum 220 VAC, GOKZ (nominal), 150 watts maximum

Dimensions 25-1/2 inches wide X 30-1/4 inches depth (64.8 cm wide X 76.8 cm depth) 72-1/2 inches height (184.2 cm height)

  • Important Notes
  • The following note is included in compliance with FCC rules:
WARNING: This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. As temporarily permitted by regulations, it has nat heen tested for compliance with the limits for Class A computing devices pursuant to Subpart J of Part 15 FCC Rules, which are designed to provide reasonable protection against interference in which case the user at his own expense will be required to take whatever measures may be required to correct the interference.
  • Miscellaneous

NEVER remove circuit board connections while power ts on.

NEVER replace any components with anything other than exact replacement parts.

DO NOT replace fuses with anything other than proper value. A blown fuse indicates an overload condition within the game, Replacing the fuse with a higher value can cause damage to internal components, if an overload occurs.

  • Control Panei Removal

Wilh Lie dour bo Lie game electronics Compartment ypen, disconmel the control panel harness, reach under the control panel and flip the fasteners on

Page 10

both sides of the control panel. The control pane] will now swing outwards. Slide the spring-loaded pins on both sides and remove the control panel.

  • Front Plexiglass, Interior Graphics and Graphics Frame Removal

The front plexiglass, which secures the interiur yraphics, is held in place by the control panel. Release the fasteners on the control panel and swing it down. Directly under the front plexiglass, you will notice a small frame support piece. Grab it by the hand slot in the middle and pull it from the game. The front plexiglass can now be removed easily by lifting it on the bottom slightiy and pulling it outward. The interior graphics can now be removed. You will also see the graphics frame, which is located directly behind the interior graphics. It must be removed when taking out the monitor. To remove the graphics frame, simply grip two sides and carefully lift out.

  • Card Cage Removal

If it is necessary to remove the card cage for servicing, first disconnect all the connectors. Then remove the three mounting screws, located on the front bracket. The card cage can now be slipped from under the rear bracket and removed from the game.

  • Logo Panel Removal

Underneath the logo panel are four mounting screws. Remove these and the logo panel can be |tfted from its stot. With the logo panel removed, easy access is gained to the speaker and fluorescent lamp assemblies for servicing.

  • Monitor Removal

To remove the monitor for servicing or replacement, first open the rear panel on the cabinet and disconnect the power cable and video cable to the’ monitor. Then, remove the front plexiglass, interior graphics and graphics frame as explained earlier. Remove the four bolts in each corner of the Monitor board. Now grasp the board by the hand holds provided at top and bottom and pull the monitor from the front of the cabinet.

Page 11

OPTION

UPRIGHT COCKTAIL

8 EXTRA SHIPS 6 EXTRA SHIPS

4 EXTRA SHIPS 2 EXTRA SHIPS

GAME DIFFICULTY: HARD

MEDIUM

EASY

BONUS SHIP: 10,000 POINTS 20,000 POINTS 30,000 POINTS

NO BONUS SHIP OPTION

4 COIN/1 CREDIT

3 COIN/1 CREDIT

2 COIN/1 CREOIT

1 COIN/? CREDIT

1 COIN/2 CREDIT

1 COIN/3 CREDIT

1 COIN/4 CREDIT

COIN/S CREDIT OPTION SELECTION

SWITCH #1 1 a

x x xX x

x Xx

x x

x Xx

x Xx

xX x Xx x x x

0 0 ia} c c 0

Cc Cc SWITCH #2

1 2

c c

c c

c Cc

¢ Cc

c it)

c 0

Cc 0

C 0 “x ><

>< ome oe OK

aM =< KR KOTO

w x > E

KOK OK OK

x «x kK KO OO cod

anoe

moe Oe OK OOO

wn > > KK OK OKO aooneg *

a ><

oe OK OK

> oO mK OE

an mK > OK OK OK Oe > me OK °

o

Page 12

OPTION SWITCH SETTINGS - (cont.)

OPTION SWITCH #2

I 2 3 4 5

COIN/6 CRCDIT ie) c c c O

Nn COTN/1 CREDIT 0 c Cc Oo ie)

4 COIN/2 CREDIT 5 COIN/3 CREDIT

2 COIN/1 CREDIT 0 c 0 Cc 9 4 COIN/3 CREDIT

COIN/1 CREDIT 0 c 0 0 it) COIN/2 CREDIT COIN/3 CREDIT wr

4 COIN/4 CREDIT 0 c 0 0 0

5 COIN/6 CREDIT

COIN/1 CREDIT 0 0 Cc Cc 0 COIN/2 CREDIT COIN/3 CREDIT COIN/5 CREDIT Pwr

COIN/1 CREDIT o o ¢ 0 90 2 COIN/3 CREDIT

COIN/2 CREDIT 0 0 0 Cc 0 COIN/4 CREDIT COIN/6 CREDIT COIN/8 CREDIT COIN/11 CREDIT anPpwn =

Page 13

OPTION SWITCH SETTINGS - (cont.)

OPTION SWITCH #2

1 2 3 4 5 6 7 8

1 COIN/2 CREDIT 0 ie) 0 (¢) ie) 0 fa) ie) 2 COIN/4 CREDIT

3 COIN/6 CREDIT 4 COIN/9 CREDIT

X = NOT USED O = OPEN C = CLOSED

Page 14

SELF-TEST

The G-80 system contains a built-in self-test system, activated by depressing the red self-test switch located on the CPU Board. If the cover to the G-80 card cage is in place, the switch can be activated by putting a per or pencil through the hole provided on the cover.

Basic diagnostics test sequence:

l. CPU RAM

  • Maskabie interrupts
  • First 1K of game ROMs
  • Video RAM and Hardware multiplier
  • Player start buttons

6, Display screen (visual)

  • All game ROMs

8, System inputs

  • Game controts
  • Sounds /Voice

Individualized diagnostics descriptions and procedures:

  • CPU RAM - tests all RAM on CPU card before proceeding, system needs to use this RAM for stack and variables during other tests so if any locations are bad processor will half (halt light will come on).

W

Page 15

2, Maskable interrupts - video interrupt is enabled through output port bit and all maskable interrupts are enabled inside processor, CPU then executes several HALT instructions to insure that at least one edge triggered interrupt has occured. If no interrupts occur during this test the halt Jignt will remain on constantly. This is the same result as a bad CPU RAM. This ambiguity can be climinated by checking the vertical intcrrupt another way. The system reset/power-up logic will also halt if the video interrupt is not functioning, to try this press the RESET switch.

  • First IK of game ROMs - the first IK of the first game ROM will be checked for validity. If this portion of the first ROM is bad the system will not be able to proceed because vital information defining parameters of the game are stored in this first 1K. If an error occurs during this validity check, the CPU will lock up and repeatedly flash the halt light.
  • Video RAM and Hardware multiplier - the video RAM is tested first and in the event that it tests good then the hardware multiplier is checked. If the video RAM is good, the message "ALL VIDEO RAM GOOD, MULTIPLIER GOOD“ appears. If a bad video RAM chip is found, then the message "BAD VIDEO RAM, CHIP U##* appears on the screen along with that chip's location. Due to the fact that sometimes a bad video chip causes the display to be erratic, the system also flashes out the bad chip's location on the halt light, over and over again separating the U#s with a one second on pulse.

The hardware multiplier is used in the game to multiply two 8 bit numbers together Lo form one 16 bil product. This Lest perforus a select group of multiplications, over 2,000 multiplications in actuality, designed to thoroughly exercise the process of multiplication between the software and the hardware multiplier. The messages "GOOD" or "BAD" are the only indication of functionality with respect to this test.

  • Player start buttons - one of the two "game start" push buttons on the front of the cabinet is very special. The "one player start" button was designated by the system as a way to terminate the test that is currently being run. ine reason That these two Duttons were tested relatively early in the sequence, was so that the remaining tests could use the “one player start”
Page 16

hutton for a termination signal. To be cure that these two buttons are func tioning properly, see that when untouched the status indicated is "0" (for open switch contact) and that when pushed or depressed momentarily the indicated status is “C" (for closed switch contact) during the time the button is down. This notation for switches being in the open or closed state, "0" or “C", will be used throughout the diagnostic sequence whenever the status of a switch is being displayed on the screen.

  • Screen - this test is supplied by the game logic, external to the CPU ROM, to provide a visual indication of how well the Wisplay screen i> CuncLiuning. It tests beam deflection and colors to check that all electron guns are functioning. In the display, you should see some sort of test showing the colors white, red, green and blue.
  • Ail.game ROMs - the intent of this test was to insure the integrity of all of the data in all of the game ROMs, At the time the ROMs for a game were originally generated there was an algorithm performed on each IK block of data. Each of these calculations, a form of CRC (cyclic redundancy check, similar to @ checksum), produced one 16-bit word. These words are stored, along with a Gremlin part number, in the first ROM. When this test is run, all of these 16-bit CRC words are regenerated and are compared to the known values stored in the table in the first ROM. If one of these newly calculated values does not match its corresponding stored value, then the system kicks out an error which amounts to the message "BAD ROM" followed by one or more bad part numbers of that ROM that was found in mis-match. If al] ROMs are good the screen displays: “ALL ROMS GOOD". Then the system quickly proceeds on to the next test.
  • System inputs - these inputs are referred to as ‘system inputs', simply because they control system functions, such as credit accumulation, coinage options, game configuration, etc. The diagnostic user may check to see that the coin switches, service switch, and option dip switches are functionina Properly. The open and closed switch notation applies here as described earlier,
Page 17
  • Game controls - the names of the controls that the game player would use to ‘control the action on the screen is what this test was designed to check. Make sure that when hands are off of the controls all of the switches are open.

When a particular control is twisted, pushed, turned or in whatever way activated, watch to see that the status of that control, and only that particular control, changes to reflect the action on the control panel. The screen should display from open to closed.

  • Sounds/Voice - just sit back, listen ana watch this one. All of the sounds made by the game will be produced and their respective names will appear in the center of the screen. The termination button acts sluggish during this test due to the fact that some of the sounds must be created by subroutines external to the CPU ROM. After completion of this test, the system will return

to the advertising mode.

Page 18

G-80 Bus Detail

TolFrom Coin Mechanism/Game Controls To RGB Monitor or X-Y CRT

To Sound Ampiifier/Speaker Wor

Uta

Z80A Video

4Mhz 48k - Sound and

CPU Board EPROM XY Speech Oto 2

With Game Board Boards Expansion Slots

And Coin (1 or 2 siots) On Mother Board

HO (1 or 2 slots) Il

__ 8 Bil Bi-directional Data Bus > J LU J LUI Tl LUI J

16 Bit Address Bus 80 I rT TL rT rT, us

System Control Bus

Page 19

TAC/SCAN TROUBLESHOOTING PROCEDURES

TAC/SCAN is a "state-of-the-art" electronic microprocessor based, video

game. The result of hundreds of hours of work, design, research, experiment and more work. However; as with any electronic device, component failure or other problems can result in a game that doesn't function properly, or doesn't function at all. In either case, your game is "down", and so critically, are your profits.

Your objective is to fix it as quickly as possible, and logical troubleshooting goes a long way toward that repair. Although many troubleshoot ing methods may be familiar to you, procedural logic is common among them, and might be stated in this order: visual inspection, symptom recognition, symptom isolation, function isolation, component isolation and repair. Familiarity with the equipment in question will allow you to bypass one or more of these steps, as any particular problem may be obvious to you, or may have happened before. In general though, these 6 steps form a good premise upon which to approach your “down" game.

An extremely important item in our procedure is the first mentioned, giving the gear the “once over". A large percentage of failures found in electronics, show themselves visually and often a great deal of time can be saved by inspecting for burnt or blown components, loose or disconnected wiring or connectors, or PCB traces burnt or pulled up. Thorough visual inspections become increasingly important the closer you get to the faulty item, and should be repeated each time another portion of the game 1s eliminated. Symptom recognition (as with al] electronic troubleshooting) in your game depends firet, on knowing what a proper display is, and second, knowing how your display differs from a normal one. ‘Symptom isolation follows naturally; (i.e, "I have no picture", "I have no sound", "I have no control over the car", “the picture is scrambled"), ergo, a video, audio, input or logic problem, Function isolation, such as a sync problem with the video, requires that you consider those functions that go to make up video sync. Is it a monitor problem, or an “on-the-board" problem? A monitor input check to verify the signal will tell you. Does the board have the voltage (from the power supply) that it needs? Yes? We must have a board failure, as we've just isolated down to function.

Page 20

Taking our sync problem further, before we begin our search for an individual component, let's reapply that first item in our "Logical Troubleshoot ing Procedure". Look at the board. Open resistors, diodes, and capacitors often give themselves away.

Noticing a trace litcrally burned open can save you scrious "down-time". The board looks OK, so on we go. Specific component isolation relates to the specific nature of the failure, component commonality, proper inputting (both signal and power) and proper outputting (as in the case of an output held high, low, or floating by input port failure in the succeeding state). More general problems (such as a total loss of video sync) requires the more involved Procedure of systematic elimination of possibilities. This operation can be expedited however, by dividing the circuit in half, establishing a "go-no/go" at that point, and again dividing the suspect circuit portion in half. The largest possible areas can be eliminated in this manner, dividing and subdividing until the individual component failure is found.

As we've outlined previously, any electronic repair procedure consists of a series of efforts to isolate a problem down to a “managable" level; restating our Logical Troubleshooting Procedure in 6 steps, 1. Visual Inspection, 2. Symptom Recognition, 3. Symptom Isolation,

  • Function Isolation, 5. Component Isolation, and 6. Repair.

In our TAC/SCAN game system, we are dealing with, essentially, 3 major func- tional components:

  • The Power Supply
  • The 6-80 Boards (Card Caga Module)
  • The Color X-Y Monitor

So, in a typical maintenance procedure, having isolated down to Function (Step 4.), we would next attempt to determine which of the 3 major elements is defective. In the following paragraphs, we will look at each element and some of its sub-divisions as a guide in isolating further.

Page 21

Usually, the power supply can be eliminated as the source of a problem if the games comes up on the screen. The major exception is when the game plays normally but no sounds are produced. In this case, the power supply's ampli- Tier circuit should be checked for audio signals from the sound and speech boards. If they are present on the amplifier output, then a bad speaker or connection is probably the cause of the problem. If the signals are not there, Suspect the amplifier circuits on the sound and/or speech boards.

If the picture does not appear on the screen, check the power supply for the main AC voltage to the primary of its transformer; then ensure that the G-80 boards are supplied with the correct DC voltages from the power supply. Also make sure the 3 VAC reset signal is being applied to the CPU board. If all these tests prove normal, then eliminate the power supply as cause of the problem and proceed to check the remaining functional game components - G-80 boards and monitor.

In most cases, a simple test will help to isolate a problem of no picture to either the G-80 boards or monitor. On an oscilloscope, look for varying voltage signals on pins 1 and 4 of the 4-pin Molex connector on the Timing Board. If the signals look similar to those shown in Figure 1, check for Signals swinging between 0 and +4 volts on the RGB outputs (4-pin Molex connector pins 4, 1, 2 respectively) on the Control Board. If all three outputs are at 0 volts, suspect the X-Y boards. If the signals appear normal, suspect the monitor as the cause of the problem. If however, pin 1 (to the monitors horizontal input) is held at or near +4 or -4 volts DC, suspect one Or both X-¥ boards. If pin 4 (to the vertical input) 1S held at or near +3 or -3 volts, suspect the other G-80 boards. In either case, TURN OFF THE POWER AND IMMEDIATELY DISCONNECT THE X Y¥ MONITOR. Proceed to check the inputs to D/A converters U1 and U4 (15) for active signals. Verify that none of the Character Data lines (CD0-CD7) are pulled high or low, or are floating. Check for the XCL and YCL ctock signals from U28 (16). Verify that the 15 MHz crystal clock is operating and that a 40 Hz signal is present on pin-11 of UI3 (17). Check BOS signal to be sure it is not held; signal DRAW should be switching high and low. On the Contro? Board, observe the signal FETCH to ensure it pulses high and low. Also, none of the Data lines (DO-D7) should be held high, low, or floating (C5). Check for clock signals PCC and SCL (C5).

Page 22

Look for input changes on Ul and U5 of the color circuit (C6); also, pin-3 of U4 should be active high and low. (See figure 1 in the illustrations section).

When the monitor is suspected of a problem, check for all] correct power supply voltages as shown in the schematic. Isolate incorrect voltages to either the monitor power supply or to the circuit receiving the voitage.

NOTE: The Culur X-Y Munilur cuntains a cireuit that shuts off the high-voltage oscillator when no vertical or horizontal inputs are present. 00 NOT ATTEMPT TO RAISE OR LOWER EITHER INPUT WHEN TESTING THE MONITOR. DOING SQ WOULD CREATE EXCESSIVE DEFLECTION CURRENT THAT COULD SEVERELY DAMAGE THE MONITOR. For testing the monitor, use only the outputs of the G-80 hardware. In adaition, 00 NOT operate the monitor WITHOUT proper fuses in the main AC line. If a

monitor is blowing main fuses, check the deflection amp power transistors Q605, Q606, Q705 and Q706, WITH THE POWER OFF. Shorted transistors or diodes in the deflection amplifiers will also blow main tine AC fuses.

Check the transistors in the color drive circuits for shorts or opens when one or more colors te missing from the display, and the G-80 hnards are known

to be good.

Page 23

COLOR X-Y MONITOR AND G-80 CIRCUIT DESCRIPTION

To begin our discussion of the Color X-Y Monitor, let's first pay tribute to the “other kind of monitor" - the raster-scan. As you may remember from your knowledge of raster-scan displays (like those in a TV), that the electronbeam inside the tube always moves in a predictable way. That is, it always starts at the top left of the screen and scans across it, forming a pattern of horizontal lines on the inside surface of the tube as it moves downward. When it gets to the bottom, the beam is forced back to its starting point and repeats the raster-scan movement. To create a simple display (for example, a large "+" symbol) on the raster-scan monitor, we figure out first, where we want it to appear on the screen; let's say the center, in this case. Then we generate a video signal that represents the "+", plug the signal into the monitor, and we get a "+" on the display. What we have done is intensify the electron-beam so that only those points corresponding to the "+" light up on the raster. (To see how it would look close-up, refer to figure 2 in the illustrations section.)

Notice how the vertical line is not much of a line, but more a column of stacked lines. This occurs because the raster lines, which run horizontally inside the CRT, are spaced slightly as the beam traces them. So what we see, looking at our line from top to bottom is a tiny segment of the lit up raster, then a black space, another lit up segment, another black space, and so on. Now the horizontal line of our figure is perfect, one solid, lit up line corresponding to that particular "raster". The fact that you can't get highquality traces in both directions is what led to the development of the X-Y Monitor. Tf we create that came centered "+" an an X-Y¥ display, we would see two perfect, solid lines - no gaps anywhere. (Refer to figure 3.) What Produces the high-quality, solid lines in any direction in an X-Y monitor is the electron-beam inside the CRT (there are actually three electron-beams, one for each of the three colors, red, green, and blue, although it is often simpler to think of it as one beam). Unlike the beam in a raster-scan unit, the X-Y beam can be moved in any direction we choose. All we have to do is determine where we want to move it. We also need to tel] the beam when to turn on, or intensify, to “draw” the design we want, how big to make the

Page 24

design, what color the lines should be, what angles the tines will take, and when to stop drawing. For now, remember that we are directly influencing the X-¥ beam to create our lines by moving it and turning it on when necessary; in the raster-scan, all we had to do was turn on the beam at the right times.

Impurlant vif ferences between the raster and A-¥ monitors are that tne X-¥'s have no need for vertical or horizontal oscillators and drive circuits,

since these predetermine the electron-beam's muvemenl., Alou, nu Flyback pulse is needed in the X-¥ to move the beam to the top of the raster. However, a

very high voltage is still necessary in the X-Y to attract the electron-heam to the front surface of the tube.

Before we delve into the circuits that make up the color X-Y monitor, let's consider how we actually contro} an electron-beam. Inside the picture tube neck, there is a piece of metal called a cathode. When it is charged with a voltage, it generates electrons. As the electrons are emitted, they are shaped to form a thin ray, or beam, that strikes the front of the monitor. The only way the beam will move up or down, left or right is if a magnetic field is applied around the beam. This is what the deflection coils located around the CRT neck do. There are two coils, one to move the beam up or down (VERTICAL DEFLECTION COIL) and one to move it left or right (HORIZONTAl DEFLECTION COIL). So, by running some current through either coil, we create a magnetic field around the beam to deflect it in any direction. The larger the current we put through either coil, the stronger the magnetic field and the more the beam will deflect.

While we're on the subject of beam movement, consider why this monitor is called an "X-Y monitor", Picture our "+" symbol on the screen again; the horizontal line is called the "X" axis and the vertical line is the "Y" axis, hence "X-¥ monitor". Make a mental note that whan we move the beam horizontally, we are moving it on the X-axis; moving the beam vertically occurs on the Y-axis. Let's look closer at the color X-Y monitor circuits and see where this deflection coil current comes from. (For the following explanation, please refer to the schematic of the monitor in this manual.) The circuitry primarily consisting of IC 600 (15-2156-01) accepts two varying voltage levels, one for Vertical, one for Horizontal, from the G-80 boards. These

Page 25

voltages are called ANALOG signals because they represent all voltage levels between two pre-determined levels.

Let's say that we want an analoy signal Lhat can vary between Lwu vullages, +3 and -3 volts. We could control it to look like this on an oscilloscope:

As the signal changes, it moves through all possiple voltage levels that exist between +3 and -3 volts. Don't confuse this type of signal with a digital one. The digital signal switches between 0, and typically, +5 volts. It does not drop to a negative voltage level. As these varying valtages come into the X-¥ monitor, they activate, first the Input Driver, intended to set a proper reference, and the X and Y power amplifiers (Q 600-606, Q 700-706). These amplifiers control the current that flows into the X and Y deflection coils, depending on the voltage levels on the inputs, and the input current set by Limiters Q 201, 202, 251, 252. Remember that this current controls the electron-beam movement, so if we vary the input voltage, we vary the output current and the airection of tne peam. Tne rollowing cnart will Clearity tnis:

INPUT VOLTAGE BEAM MOVEMENT

Y~AMP Positive Up (Vertical) Negative Down

X-AMP Positive Right

(Horizontal) Negative Left

Earlier, we said that there has to be a way to turn on, or intensify the electron-beam to create an image on the screen. Well, there are three more Inputs Lo the X-Y that alluw us tu du Just ial; they are Lhe culor inputs R,G,B and they accept analog signals from the G-80 hardware. These color

Page 26

signals activate the intree color electruu-beaus Uiruugh the circuits in the Video PCB, Using what we know so far, let's apply it to an actual example of drawing something simple on the screen - a white line for instance. (Refer to figure 4 - illustrations section.)

Point A, the center of the screen, is the starting point for the electronbeam. To move the beam to point B, we have to supply voltages to the monitor's inputs that cause the beam to move at a 45 degree angle. To do that requires two increasing positive voltages on the horizontal and vertical inputs. (See tne cnart above). Not only are tnese voltages positive fn this case, iney also have to be equal. And if they are equal, the deflection coils will force the beam the same distance both upward, and to the right, at the same time. Moving at any other angle is just a matter of making one coil deflect more or less than the other. Again, notice that both coils force beam deflection simultaneous ly.

Since we don't want this 45 degree line to show up on the screen, we don't feed any voltages to the RGB inputs. But, we know the beam is at point B, awaiting further deflection. Now, we cause the voltage on the horizontal (X) input to go negative and leave the vertical voltage where it is. Also, we turn on the RGB inputs to give us a white line. From the chart, you can see that these voltages will cause the beam to move to the left, horizontally, to point C. Qur line is complete, and here is what our input signals looked 1 ike during this process:

+V Horizontal (X) Voltage 9 Vv +V

Vertical (Y) Voltage

Page 27

In our example, we made a very short line, considering we could have drawn one clear across the screen. In order to draw longer lines, in any direction, we simply increase the positive or negative voltage on the inputs. Remember the higher the voltage, the more the deflection, the longer the line.

The remaining circuits in the monitor are a power supply, a CRT and brightness control (CRT PCB), and high voltage generator. Here are Functional Block, and Signal Flow diagrams for the Color X-Y Monitor:

Page 28

INPUT DRIVER

Q 800-803 P 8008 J 800 P-100 6] BLUE xf x 5| GREEN y[2 Y

  • feo GND GND 3] XIN BLue [4 2] YIN GREEN |S 1] ano rede, Ic 600 Q 600-604 Q 700-704 Q@ 400, 401

O= , DEFLECTION AMP PCB

al P 401 x 7 + FB] ocomuss ac

pPso0 y[4 P 402 rer [a a REF [7 FAN

Q 605 P 400 Q 606 Fe] asvac POWER SUPPLY cT | asvac eg@geog J 600 >> > 33> 4 Bex i = 8B Y +7 oS S48 REF [1

  • REF [7 P 700 !

x [4 REF [1 rer [&

Q 705 Q 706 ul-T [>]

PTsI-TaTs

al~T-TT]

th

COLOR X-Y MONITOR

MODEL G08-003 T~f-T+To

r

Page 29

X-AXIS CURRENT LIMITER

  • XIN 1] REF 47] ner P 200

Q 201 Q 202

P 201 4] X OUT 4] REF 7] ser VIDEO PCB

BLUE GREEN RED

{| Q 100-105

[-@ | +55VDC BLUE

  • 03VDC GREEN t-# |-9.1VDC. RED

4TYIN

  • REF
  • REF 4] Y OUT 1] REF 7| REF

Pst

Q 251 Q 252

BRN

Y-AXIS CURRENT LIMITER H.V. PCB

Ic 900 22.5KV Q 900-903 x BRIGHT. o x 8

HAT ty v + 126VDC 6.3VDG. +9.1VDC -9.1VDC

GND GND NOT LISED ZS] ole] ~ Jala] a]o[n]=.o

vG2 5] H.V. REGU- LATOR Q 320-323

+ 126V0C IN + 100VDC OUT

Page 30

Refering back to the monitor schematic for the following discussion, the circuitry in block A serves two purposes. First, it compensates for a type of distortion known as the pin-cushion effect. This occurs because the electronbeam must travel a greater distance when striking the edges of the CRT than when it hits the center. If we cause the beam to trace along the edges of the CKI, the beam would draw a box with 1ts left and right sides bowed inward. To compensate for the effect, this circuit offsets the point where the beam would normally strike the CRT surface.

Secondly. this circuit contains two error amplifiers, one for the horizontal and one for the vertical inputs. Each error amp has two inputs; one is set to zero volts, the other accepts the analog signal from the G-80 system, sensing current movement in the deflection coil. The anatog signal is allowed to pass through the error amps and drive the deflection (power) amps. The deflection amps are shown in blocks B and F. The outputs of the X and Y power amps pass current through their respective deflection coils. The output leads of the two culls are connected back Lu Lhe analuy inpuls of the respective error amps, as mentioned above. This acts as an error, or feedback, signal and ensures that the current through the deflection coil remains proportional to the voltage on the error amp inputs. If this signal were not provided, there would be a slight deflection error when an analog input signal was present.

The outputs of the X and Y deflection amps can swing petween +60V and -60¥. This voltage is high enough to provide up to 8 amps, peak-to-peak, of current through the deflection coils.

The color drive circuits are located in schematic block C and they accept a 4 volt maximum signal on the RGB inputs. The outputs drive the three electron-beams in the CRT. Three neon glow-bulbs, NE-100, 101, and 102 act as spark arrestors for the color-drive outputs to the CRT. In block 0, the CRT is shown, as well as the brightness adjustment for it. The circuit of D 409, R 411, R 410 is a spot-killer that prevents the electron-beams from burning a hole in the phosphor surface of the CRT when the monitor is turned off. Section G of the schematic consists of the high-voltage oscillator in IC 900 (14-2155-01) which operates tne ntgh-voltage transformer, T 901. This transformer is technically a flyback type, but it is not used to deflect the beam.

Page 31

The IC serves two other functions; it senses the presence of the 10.3KV through R 921 and R 932 and cumpares iL against Lhe 9.1 supply vultaye Lu ensure a regulated output, and also senses the varying current in either deflection coil. If no change is detected, the IC shuts down the high-voltage oscillator to prevent the beam from “burning” the face of the CRT.

Finally, the X-Y power supply is shown in block E, generating the following voltages: +60V to X-¥ power amplifiers +55V to RGB video drivers and spot killer +9.1V to the IC's +120V. to the EHT oscillator

A degaussing circuit is provided through D 404, D 405, and R 400. The CRT is automatically degaussed when R 400 is conled sufficiently ta conduct current through the degaussing coil.

G-80

It's not hard to imagine how fast the input signals to the color X-Y monitor must be changing in order to produce the game displays. It's also obvious that a computer must be making ail this happen. That is exactly the case with the G-80 hardware used in Color X-Y game. It contains two new boards, the X-Y Timing and X-Y Control boards that produce the X-Y monitor input signals. The G-80 still relies on its CPU, EPROM, Sound, and Speech hoards ta camplete the computer.

But what does a digital computer have to do with producing the analog signals required by the X-Y monitor? Basically, the computer converts certain digital signals into analog ones. On the G-80 X-Y boards are circuits (some are actually single IC's) called Digital-to-Analog converters, D/A for short. These circuits accept a particular digital word, that is, a string of 0 and +5V vullage levels. The D/A cunverter senses Lhe word and outputs one anu unly one voltage level which corresponds to the digital word. For example, we could dasign a simple D/A converter that would generate the following voltages when we input certain digital words:

Page 32

DIGITAL WORD ANALOG OUTPUT

0000 -1 Volt wi 11 Volt

1000 Q Volt

This is a very basic case, but it shows that, for a particular D/A converter, we always produce one voltage level from the corresponding digital input. If we cycle through a variety of digital inputs, we'll get a variety of output voltages. If we do this fast enough, we actually create a rapidly varying range of output voltages. This output 1s exactly the king of signa) we need to drive the deflection coils in the monitor.

Now that we know where the analog signals come from, what about the digital

ones? Before we can display anything on our X-Y screen, we have to ask some questions: (Answers are provided for examples sake)

QUESTIONS ANSWERS

1, What do you want on the screen? A Urlangle.

  • How many? One.
  • What design? - What angle? Equalateral (3-60° angles).

4, What size? 3" on a side.

  • Positioning? Centered on the

screen.

  • What colors? 2 sides white, 1 side

blue.

  • Screen alignment? Like thts:

BLUE,

Page 33
  • What will it do? dust sit there.
  • How many lines does the electron- In our triangle, the beam have to trace? beam must make 4 lines:

B,

D ‘blue

A (even though we don't see it), B, C, and D.

Now that we have our specifications, we have to store this information someplace so the Timing and Control boards can get to it and understand. That place is video memory RAM (or Random Access Memory). It holds 4096 eight-bit words or bytes. Naturally, we don't place all this into memory and hope the X-¥ boards can find it; it's stored in an orderly fashion.

First, we divide the video memory into two main groups - let's call them 1) The Symbol Instructions and, 2) The Line Instructions. Into the Symbol Instructions Section we store one group of ten words for every symbol or design we put on the screen, In our example, we have only one symbol, so we use only 10 words. Into the Line Instructions Section we put one group of four words for every Line that the beam has to draw. So. for our triangle. which requires 4 lines, we would store 4 groups of 4 words in the Line Instructions space. Every word we store in memory has one and only one address, so the same word can be called on over and over. Now let's look closer at the Symbol Instructions memory space. Here is what the 10 words do: (Don’t be concerned with the actual values of those words right now.)

WORD 1 It tells the X-¥ boards either to make the beam draw the

symbol in this group of words or not to draw it. And the same word informs the boards that either this group of words is the only group or that there are more 10-word groups to follow.

Page 34

WORD 2 and 3

WORD 4 and 5

WORD 6 and 7

WORD 8 and 9

WORD 10

Again, since groups after the

of memory:

WORD 1

WORD 2

WORD 3

WORD 4 These tell the boards where the beam is on the X-axis.

These tell the boards where the beam is on the Y-axis. The

last four words then, give the cxact coordinates of the electron-beam.

Words 6 and 7 tell the X-Y hardware what the first address is

of the Line Instructions section.

These tell the hardware how the complete symbol (our triangle) will appear on the screen, or at what angle.

This word tells what the overall size of the design will ve.

we're only making one design, there will be no more 10-word one above. Now take a look at the Line Instructions section

GROUP 1

This word tells the G-80 boards either to blank or to unblank the line. And, it informs the boards that either additional

4-word groups follow or no more groups follow. Finally, it defines the color this particular line is to be.

This word represents the length of the line tha beam is to

draw.

Word 3 tells the hardware at what angle the beam should make its line. 45°7, 90°

Word 4 defines in which of the four sections of the screen

the line is to appear - which quadrant.

The remaining 4-word groups contain the same representations of their respective lines, as in Group 1. The values will be different, of course,

Page 35

depending on how the lines differ. In our triangle exampie we would find 3 More groups of four words after Group |.

By now, you may be wondering what atl these “words” really are. Since we are dealing with a digital computer, the "words" we described above must be digital. More accurately, they are digital values of the specifications required to create our designs. We have taken the specifications for sizes, angles, shapes, colors and locations and converted them into digital words and create displays that the word represent.

Before we go any further, you should know that the words read from the video RAM didn't get there by magic. The microprocessor put them there. All words that represent all the characters and designs in a game are kept safely in EPROM (Erasable Programmable Read Only Memory), on the EPROM board. When the game is powered up the CPU moves the variuus word yruups from EPROM to RAM ‘Once situated in video memory, the words are made available to the Timing and Control boards to create displays. Rriefly, here is what the two X-Y¥ boards do with the words:

After al] the character words are loaded into video RAM, the Program

  • Counter is forced to call on the first RAM address. Here the Program Counter finds the first word in the Symbol Instructions section. One at a time, these ten words are taken out of RAM and latched into specific parts of the X-Y boaras. Tnis’séquence 1$ controlled by the liming Generator which generates 15 active-low signals; only one signal pulses iow at a time to latch the words Next, the following sequence occurs: oF
  • Word 1 is latched into U52. Last Symbol block.
  • Words 2 and 3 (from the Symbol Instructions) are loaded into the X-axis Up/Down counters.
  • Words 4 and 5 are loaded into the Y-axis Up/Down counters.
  • Wurds 6 and 7 are stored in the Vector Agagress counter.

4g. Words & and 4 are stored in the Symbol Angle latch.

Page 36
  • Word 10 is loaded into the Serial Multiplier.

Now the first 10 words of a character we wish to display are stored somewhere. If we had not wanted tu draw this character, the Program Counter woula have jumped to the next set of 10 symbol words, if there were another symbol. Once the Program Counter is finished moving out the words, the Vector Address Counter takes control of memory. This switching between the Program and Vector Address counters is governed by the Multiplexer. Through it, the G-80 Address Bus or one of the other counters can address video memory. Only one device is allowed access to memory at a time. When it is the Vector Address counter's turn to get into memory, the counter addresses the first word of the Line Instructions section. The reason for this, is that the Vector counter was Previously loaded with words 6 and 7 in the Symbol Instructions section. These words tell the Vector Address counter the locations of the first word in the

Line Instructions section. Now the Vector counter causes the Line Instruction words to be moved out of memory, one at a time. Here is what happens to the group of four words:

  • Word 1 is stored in the Color Latch and in U52, Last Vector.
  • Word 2 is stored in the Vector Length counters.
  • Word 3 is loaded into the Vector Angle circuit.
  • Word 4 is used in the Vector Angle circuit.

Up to this point then, 10 words that describe some symbol and 4 words that represent one line in that. symhn] have heen clacked out of memory. When the Vector Address counter takes out the last group of words that represents the

last line to be drawn, memory access is switched back to the Program Counter. It will now either restart the sequence as before (if there is another symbol to be drawn) or it will stop until the counter is reset to the beginning again.

Now the system is ready to draw its first line, to actually move the beam, because we have yiven il exact specifications to go so. Tne position or tne electron-beam is now known, (Words 2 through 5 in the Symbol Instructions) so

Page 37

we know where the beam will start to draw. Then, the X-Y boards calculate the Tength and angle of our first line. Anu they knuw Lhe color, If any, or tnis line. (In our triangle, recall that our first line, A, is one that we Shouldn't see, although it must be drawn. We also know that it must be drawn at a 0° angle, straight up.) The boards calculate the line length and angle

by assigning a certain number of digital clock pulses to these qualities. The circuitry acts as a digital “ruler” and “protractor” and measures any line, in terms of how many pulses in length and angle it is. All this figuring is performed by the Full Adder's, 2708 EPROM and Rate Multipliers. The output of each Rate Multiplier (XCL and YCL) is a string of clock puises that clock the respective Up/Down counter, X or Y. But the pulses are not just random pulses, they are the digital equivalents of a line with a particular length and angle. So we clock both Up/Down counters at the same time with tnese pulses. Doing so we force the counters to start counting from the beam position words previously Stored in the counters. The important point is this; if we change the digital values of the beam position words, we change the position of the beam through the D/A converters. How far, and at what angle we change the beam depends on the amount of pulses applied to the Up/Down counters. Just before the beam is moved, the color of the line (black included) is sent to the monitor through the RGB D/A converters.

There you have 1t - one line. For more lines, the G-80 system rapidly follows the same procedure of reading the symbol and line words, latching them, calculating Tine values, color values, and then furcing the beam 1 ine-byline to form complete symbols.

Notice that throughout our discussion, we have mentioned the microprocessor's role just once; loading the character word into memory. During an ‘actual game however, it does more than act as a "loader". Whenever we want to move our symbols on the screen, for example rotate the triangle, we need some way of changing all those words to represent new lines and angles. The CPU fulfills this job nicely. Under program control, the CPU is told when and how to alter these words to create a whole range of dynamic displays - different colored lines, new angles, longer or shorter lines, bigger or smaller characters, whatever the game play calls for. Alsu, Lhe micruprucessur yoveris. functions such as player control] and coin inputs, or sound and speech outputs.

Page 38

The CPU then, gives us the variety and color in our X-Y games. - PLEASE NOTE: Tne destgnations in parentnesis wiil be used throughout the tollowing detailed discussion to refer the reader to the proper schematics. C = X-Y Control Board (P/N 800-0163) sheets 5 and 6. T = X-¥ Timing Board (P/N 800-0161) sheets 5, 6, and 7. e.g. (C6) = Control Board, sheet 6.

The CPU addresses video memory, U24-U31, through multiplexer IC's U48 and U49 (C5). Character words are taken from memory as the Program Counter, ICs U33, U34, U22 (C5), addresses them through multiplexers U36, U49, U35, and U2] (C5). If Word 1 (Symbol Instructions) says to not display a symbol, the Program Counter is advanced 10 counts by U33, a full adder, which adds 10 to the counter when signal ADD goes low. The Vector Address counter is composed of U10, Uil, and U1Z (C5) and is loaded with the first adgress of the Line Instructions from video memory's Character Data Bus, CD0-CD7. The CPUs Data Bus, DO-D7, is brought to the memory through a bi-directional buffer, UI4 (CS). The signal labelled FETCH (C5) latches the various Character Data words from memory. The MUX (C5) signal commands the multiplexer ICs to allow either the CPU, Program Counter or Vector Address counter to address memory. MEMR (memory read) and MEMW (memory write) come from the CPU board to read from or write to the RAM. Signal VCE (C5), Vector Clock Enable, increments the Vector Address Counter. PCC (Program Counter Clock) is the string of pulses that advances the Program Counter; PCR (Program Counter Reset) ensures that the Program Counter starts counting at the first location in video RAM each time PCR goes low. This signal uccurs first al puwer-up and then 40 times a second during Program execution. So, it causes the X-Y monitor to draw and re-draw each symhol on the screen 40 times a second. The signal is generated from the master clock (crystal Yl and U14, 17) by U31-U34 and UZ2 (T7). The other clock signals (VCE, PCC, FETCH, ADD, MUX, and VCL) are all generated by the X-Y Timing board (17).

The outputs of the Last Symbol and Last Vector latches (U52, T7} are AND gated together with the signal END, which originates from the Control board's U18 (C6). When UI8's output goes iow, it signifies that no more symbols are to be drawn. Then the Program Counter is reset by the 40 Hz signal to the start of the vidco memory to rcpcat the display sequcnce. U22 (T7) is the DRAW latch and its output, through U2], creates the DRAW signal which initiates a

Page 39

sequence that causes the beam to draw. This sequence occurs on the Timing Board, sheet 6; by this time, all video words have been stored in their proper Places in the system. On the Timing Board (77), the vector angle is in U56, the symbol angle in USS. So when DRAW goes high, it causes strinys of digital Pulses that represent the vector and symbol angles to be generated. These streams of pulses (from U28, 16) are the ones that clock the X and Y Up/Down counters, shown on T5 (U15-U20). U25 (T6) tells the counters in which direction to count, up or down (D/U X, D/U Y). Then, the outputs of the Up/Down Counters, X and Y, become the digital words that are converted to analog signals by D/A converters U1 and U4 (T5). On Amps U2 and U3 (T5) convert current from the D/A converters to voltage levels. These levels drive the Vertical and Horizontal inputs to the monitor. Signals DRAW and VCL are combined in UZ’ (16) to form DCL (Vraw Clock). [his signal clocks gown the Vector Length counters U15, U16 and U17 (C6) which contain words that represent various lengths of the Tines to be displayed. When the counters have counted down to Q, the END signal becomes active. As the X and Y Up/Down counters are clacked, their outputs are sensed by U5-U10 (T5), which are multiplexers. The multiplexers are necessary to tell the system when the beam is off the screen. It does this by generating the BOS signal (T5). Then BOS is AND gated with DRAW at US (C6), to blank (turn off) the beam whenever BOS goes low.

U3 (C6) compensates for the inherent delay in deflecting the electronbeams. It provides a number of taps to select a range of delay times. From U2 (C6), the color word is read ana applied to the RGB D/A converters U5, UI and associated diodes and resistors. The RGB outputs go directly to the color X-¥ monitor.

U50. a 74LS154 (T7) decoder IC, selects one of 15 outputs by making the output low. The outputs sequentially store the video memory words, one at a time. U50 is enabled at pin 18, forty times per second by U22 (T7), and at pin 19 by U21. U51 sequences U50 through its 15 count cycle; at count 14, pin 16 of U50 goes low to initiate the DRAW signal through U40, U2] and U22 (T7).

The circuitry at the top of schematic C6 (U45, U51-U54) is not used in yenerating and aisplaying characters on tne X-¥ monitor. Its Tunction 1$ to perform lengthy calculations under software control.

Page 40

ADJUSTMENTS AND SPECIFICATIONS

On the X-Y Timing Board, there are two potentiometers that adjust the Outputs of the X and Y current-to-voltage converters (U2 and U3, respectively); they are:

R3 (X) R6 {Y) u2

Uz

On the monitor, there are a number of factory-set adjustments. DQ NOT USE THESE CONTROLS. They are:

R106

R117

R6iT

R702 R917 R918

R9ZO

The following controls can be used to adjust the monitor if necessary:

R605

R712

R107

R118 R136

R930

R922 Vertical

Horizontal

Red

Green Blue

Brightness Focus

Input specifications from the C-80 boards to the color X-Y monitor are:

Vertical Input Horizontal Input Red Input Green Input Blud Input 43V maximum +4V maximum +4V @ full brightness +4V @ full brightness +4V @ full brightness

Page 41

VOLTAGE ANALYSIS FOR THE GO8-003 COLOR X-Y MONITOR

DEFLECTION PCB

P 900 (EHT) Pin 1 2.8 VAC

2 3.5 VAC

3 -9.1 VOC

4 9.1 VOC

5 GRD 6 GRD

7 5.0 VAC

8 120 VOC

9 OPEN

10 400 vOC

0 401 - cathode 63 VDC

D 403 - cathode 63 VDC

D 400 - anode -63 VOC

D 402 - anode ~63 VOC

ZD 400 59 VDC ZD 40) 9.0 VDC ZD 402 -9.1 VDC

Q 400 - base 59 VDC, - emitter 58.8 VDC, - coliector 63.5 VDC Q 401 - base 9.7 VOC, ~- emitter 9.1 VDC, - collector 17 VOU IC 600

Pin 1 0 10 0

2 4.2 VDC VW 0 3 oO 12 -9.1 VOC 4 0 13 0

5 0 14 0 6 9.1 VOC 15 0

7 7.5 VDC 16 0 8 0 Vv 0

9 0 18 4.2 VOC

Q 600 - collector 34.5 VOL Q /0U - collector 35.9 VUL Q 601 - collector 0.8 VOC Q 701 - collector 0.5 VDC

Page 42

Q 602 -

Q 603 -

Q 604 - Q 605 -

Q 606 -

EHT PCB

IC 900 Pin

Q 901 -

Q 902 -

Q 903 collector

collector

collector collector

base emitter

collector

base

emitter

emitter

base

collector

emitter

base

collector

emitter

base

collector ~0.5 VOC

63.5 VDOC

-63.9 VOC

63.9 VOC

0.1 VDC

0.1 VOC

-63.9 VOC

-0.1 VOC

-0.1 VOC

0.4 VOC

0.1 WDC

-9.1 VOC

9.0 VOC

0.7 VDC

1.7 VOC 7.5 VOC

0.1 VOC

8.0 VDC

7.5 VDC

U.3 VUL

0.3 VOC

0.5 VOC

)

0.5 VOC

3.0 voc Q 702 Q 703 Q 704 Q 705

Q 706

Wy collector

collector

collector

collector

base

emitter

collector

base

emitter -0.8 VOC

63.5 ¥OC

-63.5 VOC

63.9 VOC

0.1 voc 0.1 WoL

-63.9 VOC

-0,1 VOC -0.1 VOC

1.7 VOC

8.7 VOC

8.7 VOC

2.3 VOC

9.0 VOC 0.5 voc

0.1 voc 8.7 VDC

Page 43

illustrations

Raster-Scan i Display- : i

| Nice Line i

Figure 1 Figure 2

NA moniter Nice Lines:

Figure 3 Figure 4

Page 44

TOP ASSEMBLY

ITEM NO. PART_NO. QTY REQD.

1 130-0020 I

2 130-0002 1

3 140-0021 1

4 140-0055 1

5 220-0194 2

6 220-0167 2 7 220-0178 2

8 200-0025 1

9 420-0636 1

10 250-0038 1 1 250-0048 1

12 250-0458 1

13 250-0481 1 14 250-0492 1 15 250-0497 2

16 420-0800 1

7 280-0345 a

18 253-0272 1

19 253-0222 2 20 253-0228 ]

al 800-0295 1

22 280-0005 30

23 280-0324 2

24 280-0327 6

25 280-0360 2

26 280-0359 2 27 390-0019 1 28 420-0798 1 29 420-0030 1

31 420-0796 ]

32 420-0795 1 DRAWING NUMBER 800-0160-01

DESCRIPTION

Speaker Game 6 x 9, 10W Speaker Cover 6 x 9

Cover J-Box

Cabinet Universal Upright

Coin Mech/W Light Lock Coin Mech Door (& Back) Draw Latches

19" X-¥ Monitor

Tag, Extra Value Molding Strip Clip Switch Saddle G-80 Cage Strike Plate Molding Logo Panel

Clamp Component Board Decal, Dipswitch

Tie Wrap, Screw Mounted Panel Logo Coin Receptacle Monitor Panel Clear

Assy Fan Cabinet Cable Tie

Cable Clamp Nylon Base Tit Wrap

Washer Lack, Lock

Crimp Sleeve Lamp Fluor Game Instruction Decal Decal Caution

Graphic Interior Manual

Page 45

TOP ASSEMBL Y-Cont inued

ITEM_NO. PART_NO. QTY REQD.

33 420-0568 1

34 420-0624 1

35 800-0145-01 i)

36 800-0147 1

37 800-0178 1

338 800 0190 1 39 800-0191 1

40 800-0192 1 4i 800-0232 1 42 420-0656 1

43 800-0255 1

44 800-0277 1 45 800-0279 1

46 800-0280 J

47 800-0284 1

48 800-0285 1

4g 800-0286 1

50 800-0290 1

51 800-3 265 1

52 800-3267 1

53 800-0315 54 281-0014-28 4

55 283-0024-00 4

56 284-0004-00 q

57 284-0034-00 6

58 284-0016-00 25

59 800-0276 1

60 282-0005-20 1 61 284-0036-00 45

62 283-0025-00 7 63 282-0005-24 3

64 281-0044-08 2 DRAWING NUMBER 800-0160-01

DESCRIPTION

Decal FCC Light Baffle

Assy J-Box Assy Fluor Lamp 2

Assy Harn Power Assy XFMR EMI Assy Game Power Supply Assy Speaker Harn Assy Harn Gnd Intf Mech Decal Self-Test Instructions

Assy Harn AC Monitor Intf X-¥ Assy Vol Control Block Assy Conn Bracket Assy Coin Counter

Assy Harn Gnd Coin Mech Univ. Assy Harn Gnd Game Elec. Univ. Assy Harn Gnd G-80 PS Univ. Assy Gnd Strap Control Pnl Univ.

Assy Control Panel Assy Game Electronics Assy Harn Coin Mech Lighting Scr Oval Hd Mach #8-32 x 1,750

Nut Hex Mach #8-32

Washer Flat Std U.U. steel #3

Washer Lock Split Steel #8 Washer Flat Small 0.D. Steel #10

Assy Harn Coin Mech Bolt Carriage Hd Mach #10-24 x 1.250

Washer Lock Split Steel #10 Nut Hex Mach #10-24 Bolt Carriage Had Mach #10-24 x 1.500 Scr PN HD Phi S/M Type A/AB #8-15 x .500

Page 46

TOP ASSEMBL Y-Cont inued

ITEM _NO. PART NO. QTY REQD.

65 281-005 2-08 4

66 282-0017-24 67 286-0044- 12

68 282-0017-16 2 69 284-0027-20 14

70 283-0007-00 4

nN 284-003/+UU Wu

72 281-004 2-32 6

73 284. 0002-00 4

75 281 -0045-12 27

76 284-0006-00 12

7 281-0074-12 ia

78 283-0015-00 ] DRAWING NUMBER 800-0160-01

DESCRIPTION

Scr 82° Flat HD Phi S/M Type A/AB

#6-18 x .500

Bolt Hex HD Mach #1/4-20 x 1,500

Scr PN HD Phi S/M Type A/AB B1k #8-15 x

Bolt Hex HD Mach 11 1/4-20 x 1.000 Washer Flat 1.250 0.0. Steel #1/4 Nut Hex Self-Locking Mach #1/4-20 Washer Lock Split Steel #1/4 Scr PN HD Phi S/M Type A/AB #6-18 x 2.000 Washer Flat Std 0.D. Steel #6

Scr PN HD Phl S/M Type A/AB #10-12 x .750

Washer Flat Std 0.D. Steel #10 Scr 82° Flat HD Phil Wood #8-15 x .750

Nut Wing Mach #10-24

Page 47

SECTION A-A a é ey ead

Se & TOP ASSEMBLY 700-0160.0%

Page 48

10-09 10-002 ATSWASsSY dOL

Page 49

700-0106-01 TOP ASSEMBLY

+ TIE BACK UNUSED LEAD UBING ITEM *22

Page 50

TOP ASSEMBLY

ITEM NO. = PART.NO. QTY _REQD.

1 130-0020 1

2 130-0002 1

3 140-0021 1

4 140-0055 !

6 220-0167 2 7 220-0178 2

8 420-0656 1

y 420-0636 1

10 250-0038 1

it 250-0048 1

lz 250-0458 1

13 250-0481 1 14 250-0492 1 15 250-0497 “2 16 420-0800 7 280-0345 VW 18 253-02/2 I 19 253-0222 2 20 253-0228 1

21 260-0001 1 22 280-0005 30 23 280-0324 2 24 280-0327 8 25 280-0360 2 26 280-0359 2 27 390-0019 1

29 420-0030 1

31 amn-N796 1 DRAWING NUMBER 800-0160-00

DESCRIPTION

Speaker Game 6 x 9, 10W

Speaker Cover 6 x 9

Cover J-Box

Cabinet Universal Upright

Lock Coin Mech Door (& Back) Draw Catch

Decal Self-Test Instructions

Tag, Extra value Molding Strip Clip Switch Saddle G-80 Cage Strike Plate Molding Logo Panel Clamp Component Board Decal, Dipswitch Tie Wrap, Screw Mounted Panel Logo Coin Receptacte Monitor Panel Clear

Fan Axial Cooling

Cable Tie

Cable Clamp Nylon Base Tie Wrap Washer Lock, Lock Elec. Crimp Sleeve Lamp Fluor

Decal Caution 115¥

Graphic Interior

Page 51

TOP ASSEMBLY-Continued

ITEM NO. PART NO. QTY REQD.

32 420-0795 1 33 420-0568 1

34 420-0624 1 35 800-0145-01 q 36 800-0147 1 37 800-0178 1 38 800-0190 1 39 800-0791 1

40 800-6192 7 4 800-0232 1

42 200-0025 1

43 800-0255 1 44 800-0277 1 45 800-0279 1 46 800-0280 1 47 800-0284 1 48 800-0285 1 49 800-0286 ] 50 800-0290 q 51 800-3 265 1

$2 800-3267 1 53 420-0798 1

54 281-0014-28 4 55 283-0024-00 4

56 284-0004-00 4 57 284-0034-00 6 58 284-0016-00 25 59 800-0276 1 60 282-0005-20 W 6] 284-0036-00 45 62 283-0025 -00 7 63 282-0005-24 3 DRAWING NUMBER 800-0160-00

DESCRIPTION

Manual

Decal FCC Light Baffle Assy AC Junction Box Assy Fluor Lamp 2 Assy Harn Power Assy XFMR EMI Assy Game Power Supply G-80 Assy Speaker Harn G-80 Assy Harn Gnd Intf 19" Electrohome X-Y Clr Monitor

Assy Harn AC Monitor Intf X-¥ Assy Vol Contro] Block Assy Conn Bracket Assy Coin Counter Assy Harn Gnd Coin Mech Univ. Assy Harn Gnd Game Elec Univ. Assy Harn Gnd G~80 PS Univ. Assy Gnd Strap Cont Pni Univ. Assy Cont Pni Assy Game Electronics Necal Game Instructions Scr Oval Phil Mach #8-32 x 1.750 Black Nut Hex Mach #8-32 Washer Flt Sta 0.D. Steel #8 Washer Lock Split Steel #8 Washer Flt Small OD Stl #10

Assy Harn Coin Mech Bolt Carriage HD Mach #10-24 x 1.250 Washer Lock Split Stl #10 Nut Hex, Mach #10-24 Bolt Carriage HD Mach #10-24 x 1.50

Page 52

TOP ASSEMBLY-Cont inued

ITEM _NO. PART NO. QTY REQD.

64 281-0044-08 2

65 281-005 2-08 4

66 282-0017-24 8 67 286-0044-12 4

68 282-0017-16 @ 69 284-0077-2n 14 70 283-0007-00 4 71 284-0037-00 10 72 281-004 2-32 6

73 284-000 2-00 4

75 281-0045- 12 27

76 284-0006 -00 12 77 28)-0074-12 iW

78 283-0015-00 1

80 800-0314 1

81 800-0315 1 82 800-0321 1

83 220-0194 1 84 800-0322 1 ORAWING NUMBER 800-0160-00

DESCRIPTION

Scr PN HD Phil S/M Type A/AB # 8-15 x

Ser 82° Flt HD Phil S/M Type A/AB #6-18 x .500 Bolt Hex HD Mach #1/4-20 x 1.500

Scr. PN HD Phil S/M Type A/AB Blk #8-15 x «750

Bolt Hex HD Mach #1/4-20 x 1.000 Washer Flat 1.250 0.D. Sti #1/4 Nut Hex Self Locking Mach #1/4-20 Washer Lock Split Stl #1/4 Scr PN HD Phil S/M Type A/AB #6-18 x 2.000 Washer Fit Std OD Stl #6

Scr PN HO Phil S/M Type A/AB #10-12 x

Washer Flt #10 x 3/4 Scr Flt HD Phil #8-15 x .75 LG 82°

Wing Mach #10-24

Assy Harn Power Assy Harn C/M Light Assy Harn C/M Univ. Coin Mech W/Light Assy Cord Fan

Page 53

TOP ASSEMBLY 700-0160-00

Aa SECTION A-A

Page 54

TOP ASSEMBLY

@ 2828608 © ©

ac Al, HO K PO. SOQ BEM

c (@) + 700-0160-00

2A. or ayes \eaa) Ors @) SECTION 8-8 ” ge

Page 55

TOP ASSEMBLY 700-0106-00

TIE BACK UNUSED LEAD USING ITEM "22.

Page 56

CONTROL PANEL ASSEMBLY

ITEM NO. PART _NO. Qry REQD.

1 250-0538 1 2 253-027 3-00 1 3 800-0390 1 4 240-0111 2 § 240-0006 2 6 240-0009 2

8 510-0064 6

9 280-0329 6 10 282-0005- 12 4 1 284-0016-08 4

1 284-0036 4 13 283-0005 4 14 800-0374 1

16 28] -0002- 10 4 V7 284-001 2-06 4 18 800-3 248 1

19 280-0327 2 20 280-0005 8 21 250-0565-00 ] DRAWING NUMBER 800-3265

DESGRIPTION

Subpanel Metal Graphic Control Panel Assy, Rotary Control Button, Plunger, Blue Button, Plunger, Red Button, Plunger, Yellow

Switch Pushbutton Metal Panel 1/2 IN - 13 Hex Pal Nut Bolt 10-24 x .750 Carriage Mach Washer, Flat #10-.220 I.D. x .500 0.0.

Waster Lock Split #10 Nut 10-24 Hex Self Locking Interface Assy Single Player Control Panel

Screw 6-32 x 5/8 IN Pan HD Mach Washer, Flat #6-.150 1.0. x .375 0.0. Control Panel Harness Assy

Base Tie Wrap Cable Tie Knob-Modified Rotary Control

Page 57

CONTROL PANEL COMPLETE ASSEMBLY 800-3265

Page 58

CONTROL PANEL COMPLETE ASSEMBLY 800-3265

aun @ Ye (3) »\ mx © “\ 1 ff - 7 \- :

  • 7 12.00 [305]. = (oY bee Gry ona Z = is | a
Page 59

COMPONENT SHELF ASSEMBLY DRAWING NUMBER 800-3266

Qry ITEM NO. PART NO. REQD. DESCRIPTION

1 250-0458-00 1 Saddle 6-80 Cage 2 25 2-014 2-00 1 Component Shelf UP. CAB. 3 280-0324-00 1 Cable Clamp Nylon 4 281 -0045-12 15 SCR 10-12 x 3/4" PN HD Type A/AB 5 284-0016-08 15 Washer Flt #10 Small OD 1/2" 6 284-0036-00 15 Washer Lock Split #10 7 280-0005-00 5 Cable Tie 8 800-0190-00 1 Assy XFMR EMI 9 800-0191-00 1 Assy Game Pwr Supply G-80 10 800-0277-00 1 Assy Volume Contrul Block a 800-0285-00 1 Assy Harn Gnd Game Elec. 12 800-0286-00 1 Assy Harn Gnd Pwr Supply 13 800-0314-00 q Assy Harn Pwr 14 800-3267-00 1 Game Elec. Assy 15 280-0475-00 12 Staple

Page 60

COMPONENT SHELF ASSEMBLY 800-3266

fo fefr" ia Z. la

@ — rie] feu] fr 25 @ <Q

HARNESS.

ee ol 1.5] DETAIL A_SPL =e

Page 61

GAME ELECTRONICS ASSEMBLY

qry JIEM NO. PART NO. REQD.

1 420-0560-00 1 2 420-0801 -00 1 3 600-0089-00 1 W4 800-0161-00 1 45 800-0163-00 1 6 800-0282-00 1 7 800-0296-00 1 8 800-0378-00 1 9 800-3 268-00 1 10 800-32609-00 1 YW 800-3270-00 1 12 800-030 2-00 1 DRAWING NUMBER 800-3267

DESCRIPTION

Decal Test Button Decal Electronics TAC/SCAN 7 Cable X-Y Interface Assy X-Y Timing PCB

Assy X-¥ Control PCB Assy Harn Video X-Y¥ Intf Assy G-80 Gage Univ CPU Master Harn Assy Assy CPU PCB Assy 2716 Prom PCB Sound Board Assy Assy Jumper Plug

Page 62

GAME ELECTRONICS ASSEMBLY 800-3267

3.50 [38.9] —_——s 1.00 —— tea] [e* f F ' Las ! ° Test ° (44.5) —- z ) | in -- L- ( | HS | -G) oe (el a

he ' oN 1 = SY > Holl ~O) UE UR BY ;

Page 63

GAME ELECTRONICS ASSEMBLY

EMPTY SLOT

Eid ITEM 800-3267

STEM a ITEM 1) P

PART OF ITEM #8

ao

© x —j— : I -|-U "ay | P 1 8 18] “U8 i Ts +]- o/s Lye uted = -|p ~ a éls B " ry

  • ITEM #3

{3

Td [OD

Page 64

SINGLE PLAYER CONTROL PANEL INTERFACE ASSEMBLY

ITEM NO. PART NU. QTy

REQD.

—-FOO8MNANG BPwWH 4 150-0088

151-0058 151-0059 170-0258

212-0024 212-0156

314-0055

314-0062

314-0075

314-QU85

471-0102 DESCRIPTION

Cap £ 10 uf 25V¥ ROL

Cap .01 uf 16V AX Cap .001 16V AX PC Board

Conn 12 Pin M RTA PLRZD Conn Header 15 Pin

IC 7418244

IC 74.874

IC 74LS397 IC 74LS14

Res IK Ohm 1/2W 5% DRAWING NUMBER 800-0374

REF DES.

c3

Ci, C2 c4

P30 Pio

v2, U3

US ul

u4

RI-R3

Page 65

SINGLE PLAYER CONTROL PANEL INTERFACE ASSEMBLY 800-0374

Ct ~~) iy 70.3 en an 12 [Pro : er | i

ao, RI m4. kes ke i NY

Page 66

ROTARY ASSEMBLY INTERFACE

ITEM NO.

Om wr a PART NO.

170-0160

212-0081

285-0001-04

370-0006

470-0101 QTY REQD DRAWING

DESCRIPTION

PC Board

Conn M 4 Pin RTA PLRZO

Rivet .125 Dia X .25 Lg Opto Electric Fneoder XSTR Res 100 Ohm 1/4W 5% NUMBER 800-0382

REF DES

Pl

DSI, ps2 Ri

Page 67

Rotary Interface Assembly 8UU-0382

TOP

DSI —,

DSzZ

BOTTOM

DEVICE ORIENTATION LOCATION NUMBER MARK

H2IAZz NOTCH FACING BOTTOM

HeIAD NOTCH FACING BOTTOM! K-2133 DOT FACING TOP

k-2133A DOT FACING TOP

Page 68

ROTARY CONTROL ASSEMBLY

ITEM NO.

Pwr a PART NO.

281-0031-04

284-0011 -05 800-0382

800-0383 QTY REQD

—~ 3 WW ®% DRAWING NUMBER 800-0390

DESCRIPTION

Scr #4-40 X 1/4" PN HD Thd Forming Wshr #4 F1, SM OD, Stl

Rotary Interface Assy Rotary Bracket Assy

Page 69

ROTARY CONTROL ASSEMBLY 800-0390

2PL

Page 70

FLUORESCENT LAMP 2 ASSEMBLY DRAWING NUMBER 800-0147-00 FLUORESCENT LAMP 2 ASSEMBLY DRAWING NUMBER 800-0147-01

QTY REQD. ITEM NO. PART NO. 00-01 DESCRIPTION

q 217-0041 2 2 Conn Pin Amp 2 211-0044 1 1 Conn Cap Amp ¢@ Pin

4 211-0166-00 1 - Gonn Crimp Ring #10

6 280-0361 - 1 BSHG STR RLF AC Cord

  • 280-0362 - 2 Elec CRP SL 24-18 AWG

9 281-0002-06 1 1 SCR #6-32 x 3/8" PN HD Mach

VW

14 284-0002-00 - 1 Washer Flat STD 0.D. #6

7 390-0083 ] - Fluor Lamp Fxt 18 IN 18 390-0117 - 1 Fluor Lamp Fxt 18 IN U.L.

2)

23 600-0079-00 1] 5.9" CA 2 Cond Zip Cord

Page 71

FLOURESCENT LAMP ASSEMBLY 800-0147

PART OF TEM >

=00_ASSY

Page 72

FLUORESCENT LAMP 2 ASSEMBLY 800-0147

Ol ASSY

Page 73

VOL CONTROL BLOCK UNIV ASSEMBLY

qry LEM NO. — PART_NO. REQD.

1 240-0001-00 1

2 250-046 2-00 1

3 285-0001.04 4

4 420-0623-00 1

5 475-0007-00 1

6 510-0051-00 2 7 800-0402-00 1 DRAWING NUMBER 800-0277

DESCRIPTION

Knob Volume Control

Brkt Volume Control

Rut .125 Dia x .250 LG MDRL Pull, Dome

HD, AL

Decal Oper Cont Blk Pot 10K Car PNLMNT

SW Pushbutton Slide

Harn Vol Control B1k Univ

Page 74

VOLUME CONTROL BLOCK UNIVERSAL ASSEMBLY

Cat FWAIGA \gnmon ADIAWAS

ae) 800-0277

p24

Page 75

COIN COUNTER ASSEMBLY DRAWING NUMBER 800-0280

ITEM_NO. PART NO. QTY REQD. DESCRIPTION

1 220-0008 1 Digital Counter, 6 volts 2 250-0496 1 Coin Counter Bracket 3 281-000 2-08 4 Pan Head Phillips screw, 6-32 x 1/2"

machine 4 284-000 2-00 4 Flat Washer, #6

5 2RA-NN22-NN 4 Split Lock Washer. #6 6 283-002 2-00 4 Hex Nut, #6-32

Page 76

COIN COUNTER ASSEMBLY 800-0280

4PL

Page 77

FAN CARINFT #2 ASSFMBLY DRAWING NUMBER 800-0297

qry ITEM NO. PART NO. REQD. DESCRIPTION

1260-00011Axial Cooling Fan, 110 VAC
2211-00782Conn Term Pin 20-14 AWG
3280-00057Cable Tie
4211-00441Conn Cap Amp 2 Pin
Page 78

FAN CABINET #2 ASSEMBLY 800-0297

\o- $2.00 L 13204

ke— 3.00 Av 3.00 C762 C7] 7PL

BLK IB AWG \ @ BLK 18 AWG ® CONN VIEWED : FROM WIRING END SOLDER WIRE CONNECTION 2PL

Page 79

A.C. JUNCTIUN BOX ASSEMBLY

A.C. GUNCTION BOX ASSEMBLY A.C. JUNCTION BOX ASSEMBLY

QTY REQD. ITEM_NG. PART NO. -00 Ol -02

' 140-0020 1 1 1 2 211-0165 2 2 2

3 211-0164 4 4 4

5 280-0361 1 1 1 6 270-0001 1 1 1

? 280-0007 1 1 1

8 280-0362 4 4 4 9 420-0598 1 yO 510-0013 1 1 1 W 514-0001 1 : - 12 514-0005 i 1 1 13 BUL-UUUT | } i

15 600-0079 2 Ft. 2Ft. 2 Ft.

16 280-0005 2 2 2 17 218-0002- 10 2 2 2 18 —-283-0022-00 2 2 2 ig 284-0042-00 2 2 2 20 281-0004-12 1 1 1

21 283-0024-00 2 2 2

ce 284-004 4-UU 1 i 1

24 284-007-900 1 1 1

25 —-283-0025-00 1 1 1 26 282-0005-2R 1 1 1 27 310-0016-16 1 1 1 DRAWING NUMBER 800-0145-00 DRAWING NUMBER 800-0145-01

DRAWING NUMBER 600-0145-02

DESCRIPTION

dunction Box Metal Conn Quick Fem Fully Ins]. .250 x .032 (AWG 18-22) Conn Quick Fem Fully Inst. .187 x +020 (AWG 18-22)

Bushing S/Rel AC Cord Filter EMI

Bushing S/Ret 1/2 Electric Crimp Sleeve AWG 24-18 Decal 2 Amp Fuse Switch SPOT Cherry Fuse 2 Amp 250V S.B. Holder Fuse Cord Line 3 Cond.

Cord Line Zip Cable Tie

SCR PN HD Phil #6-32 x .625 Mach Nut Hex HD #6-32 Mach

Washer Lock Int. Tooth #6 SCR PN HD Phil #8-32 x .750 Mach

Nut Hex HD #8-32 Mach

Washer Lock Int. Tooth #8

Washer Flat STD 0.D. #1/4

Nut Hex HD #10-24 Mach

Ralt Carriage #10-24 x 1.769 Mach Insul T6B .187 ID

Page 80

A.C. JUNCTION BOX ASSEMBL Y-Cont inued A.C. JUNCTION BOX ASSEMBLY-Cont inued A.C. JUNCTION BOX ASSEMBL Y-Cont inued

QTY REQD. ITEM NO. PART NO. -00 -01 -02

28 284-0004-00 2 2 2 29 420-0597 - = 1 30 420-0634 - 1 - 31 -514-0051 | 32 514-0053 - 1 - DRAWING NUMBER 800-0145-00 DRAWING NUMBER 800-0145-01

DRAWING NUMBER 800-0145-02

DESCRIPTION

Washer Flat STD 0.0. #8

Decal 1 Amp Fuse Decal 5 Amp Fuse Fuse 7 Amp 250V Fuse 5 Amp $.8.

Page 81

AG JUNCTION BOX ASSEMBLY 800-0145

C882

Sco

(*} (3) 1

SMOOTH WIRE

O—- @)——

-or 02 -00

—™ >

pS

  • 29) 9 OF -02 -00
Page 82

AC JUNCTION BOX 800-0145

TS TRANSFORMER

pan EMLFILTER ay BLK

remo | w ean | 9 Swrrcn 5 § BLU BLU BLK H _

a = gy «| F FEI SND STUD , | BLK | if '

I =

FUSE HOLDER

AG PLUG

TTI

JUNCTION BOX SCHEMATIC

Page 83

TRANSFORMER EMI ASSEMBLY DRAWING NUMBER 800-0190

ITEM_NO. PART NO. QTY _REQD. DESCRIPTION

1560-00551G-80 Power Supply Transformer
2212-00161Connector, Female, 10 Pin
3211-00059Connector Crimp
4211-00451Connector Plug Amp, 6 Pin
5211-00426Connector Socket
6211-00432Connector Plug Amp, 2 Pin
7600-00791 footZip Cord
8280-00054Cable Tie
30.5 feetElectric Strand Wire, Black, AWG 18
10280-03593Electric Crimp Sleeve
VW211-00774Connector Terminal Socket, 20-14 AWG
Page 84

EMI TRANSFORMER

XFMR

Pwr 600-0190

Pio

PH Pe ITEMS P2s 7 2PL LG BLK 3.00 76 RED 0 RED / BLK RED 3 "0 8 erY | Bik 3.00 76 5 o wo 7 BRN BRN / BLK 3 BRN ; PI3 ORN , ORN / WHT 2 ORN 3 6 WHT / BLK (0) ® war 5 @® | + ®@© CONN VIEWED BLK & | FROM WIRING END

Page 85

EM! TRANSFORMER ASSEMBLY 800-0190

Cre

t P25| FF, (

L

t t + ra ad, 7

Ye) EB) a a BoC 400 [eo32] [c.g] Pl

= a le .S0 TYP ~ c3]

DETAIL _A

Page 86

iy" X-¥ COLOR MONITOR DRAWING NUMBER 200-0025

PART NO. DESCRIPTION RES. DES.

EHT SUPPLY ASSEMBLY SEMI-CONDUCTORS 315-0118 EHT Control Circuit 1¢900 481-0211 Zener Diode 70993, 904 481-0207 Rectifier 1A 1400V D901

482-0062 Transistor 3906 Q901 482-0244 Transistor MPSUO7 Q902 482-0030 Transistor 3904 Q903 TRANSFORMERS

560-0062 Horiz. Buffer Trans. T900 560-0073 Horiz. Uutput Irans- 1901 COILS

180-0010 Horiz. Delay Chuke L900 CAPACI TORS 150-0007 4.7 uf 16V c900 152-0053 0.22 uf SOV c902 151-0109 2000 uf 50V C903 150-0015 22 uf 16V c904 151-0110 0.1 uf 100V C906, 912 150-0222 0.022 uf 100¥ c907 150-0010 100 uf 16V cal 150-0221 High Current Cap c914, 915 151-0113 47 uf 160V C916 162-0027 0.047 uf 100V cys RESISTORS 470-0103 10K 1/44 5% R900. 901, 906 460-0008 47K 1/4W 5% R902 470-0154 150K 1/4W 5% R904, 916, 934 470-0123 12k 1/4W 5% R905, 915

  • -0472 4.7K 1/4W 5% R907, 938, 939 471-0474 470K 1/ W 5% R910 460-0016 1.2K 1/4W 5% R914
Page 87

19" X-¥ COLOR MONI TOR-Curit inued

PART NO. DESCRIPTION

EHT SUPPLY ASSEMBLY CONT'D RESISTORS

475-0043 475-0044

470-0271

4/0-U4/1

471-0240

470-0330

470-0680

462-0001

464-0114

470-0333 470-0274

471-0475

471-0331

472-0470

470-0562 EHT SUPPLY ASSEMBLY KIT 482-0242

475-0035

EHT REGULATOR ASSEMBLY

SEMI- CONDUCTORS

482-0268 482-0269

481-0204

CAPACI TORS

152-0149

1d1-U108

472-0223

471-0683

472-0273

471-0473 200 Ohms Control 2k Control

270 Ohm 1/4W 5%

470 Ohm 1/4W 5% 24 Ohm 1/2W 5%

33 Ohm 1/4W 5%

68 Ohm 1/4W 5%

68 Ohm IW 5%

470K Control

33K 1/4W 5% 270K 1/4W 5% 4.7M 1/2W 5% 330 Ohm 1/2W 10%

47 Ohm 1W 5%

5.6K 1/4W 5%

PWR Transistor 5A 1400V

Focus Control

2N 6558 TIP 47 (Motorola) IN 5263

68 pf 500V 470 pf 500V 2% IW 5%

GOK 1/2W 5% 27K WW 5%

47K 1/?W 5% DRAWING NUMBER 200-0025

RES. DES.

R917 R918

R923

R924

R925

R927

R930

R932

R933

R935 R936

R937

R940

R94]

R942

Q300 R922

Q320, 321, 323 Q322 20340

C330

(331

R300

R301

R302

R304

Page 88

19" X-¥ COLOR MONI TOR-Cont inued

RAAT NO. DESCRIPTION

EHT REGULATOR ASSEMBLY CONT'D

RESISTORS 470-0331 330 Ohm 1/4W 5%

  • -03R3 3.3 Ohm 1/2W 5% 470-0363 36K 1/4W 5% 460-0008 47K 1/4W 5% 475-0048 10K Control Pot. DEFLECTION AMP PCB ASSEMBLY SEMI -CONDUCTORS

315-0117 Input Amplifier IC 481-0202 Rectifier 481-0020 Rectifier 1A 200V

481-0006 Diode IN 914 481-0204 Zener Diode IN 5263B 1/2W 56V 481-0205 Zener Diode 1N 5239B 1/2W 9.1V 481-0179 Zener Diode 9.1V¥ IW 5%

482-0248 Transistor TIB 298 482-0244 Transistor MPSU60 (Motoro la) 482-0245 Transistor 300V¥ 1/2A

482-0243 Transistor MPSUIO (Motorola)

CAPACTORS 180-0211 100 uf 80V 150-0212 680 uf T60V

150-0213 6800 uf 80V 150-0004 10 uf 25V

151-0046 Ceramic 0.1 uf Ib 2-0U96 0.1 uf 200V 150-0220 22 uf 250V DRAWING NUMBER 200-0025

RES. DES.

R305 R306 R307

R308 R310

1600 D400-403

0404-407, 409, D408, 601-605 701-705

20400

70401

z0402

Q400, 401 yeou, 700 Q601, 604, 701,

Q602, 603, 702

c401 c402

c403, 404 c405

407, 621, 721 c410

cat

Page 89

19" X=¥ COL

PART NO. DESCRIPTION

DEFLECTION AMP PCB ASSEMBLY CONT'D CAPACITORS 152-0145 2.2 pf 500V 152-0146 12 pf 500V 152-0147 100 pf 10% 500V 152-0023 47 pf 10% 500V 151-0107 j 0.068 uf 200V

152-0149 5.6 pf 10% 152-0150 560 pf S00V ZU%

RESISTORS 478-0006 Thermistor 120¥ GO Ohm 473-0330 33 Ohm 4W 10% 472-0223 2x IW 10% 470-0222 2.2K 1/4W 5% 474-0220 220 Ohm 10W 471-0822 8.2 1/2W 5% 474-0680 680 Ohm 60

470-0472 4.7K 1/4W 5% 470-0275 2.7M 1/4W 5%

470-0155 1.5M 1/4W 5% 470-0621 620 Ohm 1/4W 5% 471-0911 910 Ohm 1/4W 5% 470-0103 10K 1/4W 5% 470-0182 1.8K 1/4W 5% 470-0303 30K 1/4 5% 475-0037 50K Trim Pot 470-0104 TOOK 1/4W 5% 470-0242 2.4K 1/4W 5% 470-0102 IK 1/4W 5%

475-0038 VK Trim Pot 470-0183 18K 1/4W 5% RES. DES.

C600

C603, 703 C620, 720 (622, 722 C624, 724 C702

C725

R400 R401

R402

R403

R404 R405

R406 R410

Rall

R412

R600 R601

R602

R603, 624, 724 R604

R605

R606

R607, 710 R608, 636, 637, 715, 736, 737 RGIT

R620, 720

Page 90

19" X-¥ COLOR MONI TOR-Cont inued DRAWING NUMBER 200-0025

PART_NO. DESCRIPTION RES. DES.

DEFLECTION AMP PCB ASSEMBLY CONT'D RESISTORS 470-0622 6.2K 1/4W 5% R621, 721 470-0181 180 Ohm 1/4W 5% RA22, 625, 631, 722, 725, 731 470-0223 22k 1/4W 5% R623, 704, 705,

470-0101 100 Ohm 1/4W 5% R626, 629, 726,

471-0183 18K 1/2W 10% R627, 727 470-0271 270 Ohm 1/4W 5% R628, 728 471-0223 22K 1/2W 5% R630, 730 472-047] 470 Ohm 2W 5% R632 470-0151 150 Ohm 1/4W 5% R633

460-0056 82 Ohm 1/4W 2% R634 474-0150 1.5 Ohm 10W R635

470-0222 2.K 1/40 5% R700, 701 475-0039 5K Trim Pot R702

470-0153 15K 1/4W 5% R703, 706 470-0152 1.5K 1/4W 5% R714 472-0391 390 Ohm 2W 5% R732 470-0475 4.7M Trim Pot R930, 931 CRT SOCKET PCB ASSEMBLY SEMI-CONDUCTOR S 482-0243 Transistor MPS ul0 (Motorola) 100-105 LAMPS 390-0107 Lamp NE100-103 CAPACI TORS 151-0067 100 pf 500V C100, 110, 130 151-0112 0.1 uf 200V 101 15 1-UU5U U.U1 ut 500¥ 10% cloz, 111, 131 151-0096 0.01 uf 1000V C1l2, 113

Page 91

19" X-¥ COLOR MONI TOR-Cont inuea ORAWING NUMBER 200-0025

PART_NO. DESCRIPTION RES. DES.

RESISTORS 470-0101 100 Ohm 1/4W 5% R101, 112, 130 470-0275 2.7K 1/4W 5% R102, 113, 131 462-0056 3.3K IW 5% R103, 114, 132 472-0471 470 Ohm 1/4W 5% R104, 115 470-0122 1.9K 1/aW 5% R106, 116, 124 475-0041 250 Ohm Trim Pot R106, 117 475-0042 2.5K Trim Pot R107, 118, 136 471-0222 22K 1/2 5% R108, 119, 137 470-0181 180 Ohm 1/4W 5% R109, 121 470-0102 IK /4W 5% R110 471-0224 220K 1/2W 5% R122 471-0102 IK I/2W 5% R123 471-0474 470K 1/2W 5% R124 470-0621 620 Ohm 1/4W 5% R133 HEAT SINK ASSEMBLY

482-0260 2N 6259 Q605. 606. 705.

260-0010 Motor Blower Fan MO1 MISCELLANEOUS 200-0040 CRT val 180-0009 Deflection Yoke oY0l 180-0017 Degaussing Coil L100 213-0019 CRT PCB Socket 9101 280-0208 Yoke Wedge x ANN-0307 Input Limiter PCB x 800-0318 Input Clamp PCB x

Page 92

19” X-¥ Color Monitor 200-0025

X-Y P.C.B. COMPONENT LAYOUT

Page 93

19” X-Y Color Monitor 200-0025

C.R.T. P.C.B. COMPONENT LAYOUT

R932 +300

we z ob ) -<- 4, aaOF fs wee & $ sa ca caer Q

En Ri a rs p GMEONENT se) ee sYOUT Wr ws c 300 3 . save 02 , Roe = s 1 z noo QO i é py F wa re. ig pon, . ls oop = ooh 3 B ls E OQ ms oO

EHT P.C.B. COMPONENT LAYOUT

Page 94

G-80 CAGE UNIVERSAL ASSEMBLY

ITEM NO, PART_NO. QTY REQD.

1 250-0456 1 2 250-0499 ? 3 280-0343 1

4 420-0560 1 5 800-0105 1 6 281 -0045-06 6

7 281-0001-12 4

8 281-0001 -06 4

9 284-0001 -00 4 DRAWING NUMBER 800-0296

DESCRIPTION

G-80 Cage Assembly G-80 Cage Rracket. Split Grommet Test Button Decal 6-Siot Master Board Assembly Pan Head Phillips Screw, Type AB, 10l@ x .375 Lg Pan Head Phillips Machine Screw, #4-40x3/4 Pan Head Phillips Machine Screw, #4-40x3 /8 Flat Washer, #4

Page 95

800-0296 G-80 CAGE UNIVERSAL ASSEMBLY

Page 96

G-80 CAGE UNIVERSAL #2 ASSEMBLY

800-0296

Page 97

G-80 2716 EPROM BOARD ASSEMBLY DRAWING NUMBER 800-015

qry ITEM NO. PART NO. REQO. DESCRIPTION REF OES.

1 161-0058 13 Ceramic Capacitor, -01 uf, C2, CA, C6, C8, CO 16V AX Cli, C14, C16, C18 C21. C23. C25. C27 2 151-0060 15 Ceramic Capacitor, .1 uf, Cl, €3, C5, C7, 16¥ AX C10, Ci2, C13, Cid C17, C19, C20, C22 C24, C26, C28 3 170-0211 q PC Board 4 213-0001 23 24-Pin Dual Inline Socket XU1-xXU23 5 314-0055 1 Ic 74.5244 u25 6 314-0058 3 IC 74808 U26-U28

7 314-0069 1 Ic 7ALS10 u29

8 314-0104 1 IC 748138 u30 9 314-0120 1 IC 74LS154 U24 10 211-0008 3 Test Point Connector Pin TP 1-1P3 1 150-0088 1 Electrolytic Capacitor, C29 10 uf, 25V 12 280-0420 2 Card Ejector, Snap On

Page 98

G-80 2716 EPROM Board Assembly

800-0151

¥ L | ic f 1" ts 4,09 2 4 7. Plt t Ho , yo o> To os J 4 fi | § r

Page 99

CPU BOARD ASSEMBLY

qry

ITEM NO. PART NO. REQD.

1 150-0088 3 2 151-0005 1 3 151-0012 1

4 151-0020 1 5 151-0060 2

6 151-0061 36

7 170-0194 1 8 211-0008 4 9 212-0098 4

10 230-0013 1

nN 314-0001 1 12 314-0015 1

B 314-0018 4

14 314-0019

15 314-0055 3

16 314-0058 1

v7 314-0062 5

18 314-0066 1

19 314-0067 1

20 334-0068 2

2 314-0078 1 22 314-0083 1

23 314-0085 2

24 314-0087 1

25 314-0093 1

26 314-0099 1

27 314-0105 4

28 315-0041 1 29 315-0046 4 DCSCRIPTION DRAWING NUMBER 800-0107

REF DES.

Cap E 10 uf 25V Cap CER 680 pf 50V Cap CER .1 uf 50V Cap CER 33 pf 50V Cap CER .1 uf 16V AX

Cap CER 220 pf 16V AX PC Board ;

Conn Pin Test PT

Conn M 10 Pin RTA

XTAL 8.000 MHZ

IC NE555 Ic 7404

IC 74LS00

IC 741804

IC 7418244

Ie 74LS08

IC 74LS74

IC 74LS27

1¢ 741830

IC 74.832

IC 74LS°2 IC 7418240

TC 74L514

IC 74LS139

IC 74L$374

IC 74LS245

IC 74L$253

IC 280A

IC 2114 C43, C46, C62 cs0

C47 c49

€37-C42, C44, C48, CoI-Lol, Co3, Ub4

C1-C36

TP1-1P4

YI

ulz u30

U6, U8, U14, U9 ul8

U34, U36, U38

ul3

ul0, UIT, UI7. U2Z0, U39

u16

u37 U32, U33 u23

u4

U7, U31 u24

u3

u35

Ui, U2, U5, U9

Uu22

U26-U29

Page 100

CPU BOARD ASSEMBLY-Cont inued

ITEM_NO.

4a PART NO.

315-0050

316-0764

390-0003

471-0101

471-0102

471-0103

471-0104

471-0122

471-0220

47-0221

471-0331

477-0002

481-0001

481-0006

482-0006

482-0010

482-0014

510-0052

510-0053

213-0001

213-0002

213-0004 213-0005

510-0049

471-0472

280-0420 471-0473

151-0031 QTy REQD.

HSH RH Hw HK BH BiH HH KB KH WOW aowion aa DESCRIPTION

IC 2516 (2716) IC Prom 32x8

Led Red

Res 100 Ohm 1/2W 5%

Res 1K Ohm 1/2W 5% Res 10K Ohm 1/2W 5% Res 100K Ohm 1/2W 5%

Res 1.2K Ohm i/2W 5%

Res 22 Ohm 1/2 5% Res 220 Ohm 1/2W 5%

Res 330 Ohm 1/2W 5% Res Pack 15x2. 2k

Diode 1N4002

Diode 1N914/1N4148

XSTR 4403

XSTR PE8050

XSTR 4401

SWITCH PTANO DIP

SW Pushbutton Side PCM

SKT 24 Pin Dual INLN

SKT 18 Pin Dual INLN

SKT 16 Pin Dual INLN SKT 40 Pin Dual INLN

Switch 8 Pos Dip Res 4.7K Ohm 1/2W 5%

Card Ejector, Snap On Res 47K Ohm 1/2W 5%

Cap CER .22 uf 16V DRAWING NUMBER 800-0107

REF DES.

U25

U15

D3

RS

Kt, KS R6

R7, RB, R22 R12

R14

R2, R4, RIB R10, R11, R15-R20 RP1-RP3

DI, 02 p4

qQ7 Ql, Q2 Q3-Q6, Q8 sui

Sw3

XU25

XU26-xU29

XU15 xu21, xuz2 Sw2

Rel

R9

C45

Page 101

& ; 3005 BRE) GONG GG GOQEGENRR SOadRa (GF ’ T al sd fl Uo atin? Path i 00 aa orn bem Poof Ca iy tye —— [_ Hf 3 0000

\ sue \oene Lanna =

:

= an =

CPU Board Assembly

800-0107

Page 102

X-Y TIMING ASSEMBLY

qry ITEM NO, PART _NO. REQU. DESCRIPTION

1 151-0005 1 Cap CER 680 pf 50V 2 151-0058 25 Cap .01 uf 16V AX 3 170-0218 | PC Board 4 211-0008 1 Conn Pin Test PT

5 212-0101 1 Conn 4 Pin M RTA 6 213-0001 3 SKT 24 Pin Dual INLN 7 213-0004 2 SKT 16 Pin Dual INLN 8 213-0010 2 SKT 8 Pin Dual INLN 9 230-0009 1 Xtal 15.46848 10 280-0420 2 Cara Ejector iB} 313-0004 2 IC LM741EN Dip 12 313-0044 2 Ic AD561 13 314-0018 1 IC 74LS00

  • 314-0019 2 IC 74LS04 15 314-0040 1 IC 74.8125 16 314-0046 1 IC 74LS04 V7 314-0055 3 IC 7418244 18 314-0058 2 IC 74LS08 9g 314-0062 5 IC 741874

20 314-0070 1 IC 741386 21 314-0073 4 IC 74t$175 22 314-0074 A 1¢ 7aL$191 23 314-0076 6 IC 7418157 24 314-0078 1 IC 74LS02 25 314-0093 4 IC 7418374 26 314-0097 6 IC 74LS161 27 314-0101 4 IC 74.5283

28 314-0108 4 IC 741S107 2g 314-0120 1 LU /4L5154 30 314-0135 1 IC 74LS11 DRAWING NUMBER 800-0161

REF DES.

c?

C1-C3, C6, C8-c28

TPI

XP1, XU39, XU5O xul, Xu4 Xu2, XU3 YI

U2, U3 Ul, U4 u28

U30, U40 U27

ul4 U54, U57, U58 ul3, U2] U25, U26, U42, U43, us2 u29

U35-U38 U1S-U20

US-U10 U53 U48, U49, US5, U56 U31-U34, U41, U5) U44-U47 U11, U22-U24 U50 ul2

Page 103

X-¥ TIMING ASSEMBLY-Cont inued

QTY ITEM_NO. PART NO. REQD. DESCRIPTION

31 315-0019 1 If 2708 32 471-0202 2 Res 2K Ohm 1/2W 5% 33 471-0331 2 Res 330 Ohm 1/2W 5% 34 471-0392 2 Res 3.9K Ohm 1/2W 5%

35 475-0024 2 Pot 1K 10 Turn 36 151-0008 2 Cap CER .001 uf 50V 37 150-0088 2 Cap E 10 uf 25V RDL 38 151-0042 q Cap, Cer 4/U pf SUV 39 481-0006 2 1N914 Diode AO 151-0002 2 Cap CER 100 pf SOV DRAWING NUMBER 800-0161

REF DES.

uz9

R2, R4 R7, RB R1, R5 R3, RO c29, ¢30 C4, C5 c3t

D1, D2 C32, C33

Page 104

X-Y TIMING ASSEMBLY 800-0161

! i ial

ee oo bE J et eos a i a | Choy FS

Page 105

X-¥ CONTROL ASSEMBLY

ITEM NO.

—~SCwanan wn =

aBa RE

w MHA NNR Be HS a S8SBSRResesgnvet®seansa PART NO.

150-0088

151-0002

151-0058 170-0219

212-0101 213-0001

280-0330

314-0018

314-0019

314-0040

314-0055

314-0058

314-0059 314-0060

314-0062 314-006 / 314-0068

314-0074

314-0075

314-0078

314-0087

314-0093 314-0097

314-0099

314-0101

314-0108

314-0127

314-0128

314 0137

315-0046 Qry

REQD.

Noe wow eos

Onee ner anne eae wnw enw Hr DESCRIPTION

Cap — 10 uf 25V Cap CER 100 pf 50V Cap CER .01 uf 16¥ AX PC Board

Conn 4 Pin M RTA

SKT 24 Pin Oual INLN

Card Ejector

IC 74.500

Ic 74LS04

IC 74L$125

IC 74LS8244

IC 74LS08

IC 74LS10 IC 74LS20

IC 74.874

IC 74830

IC 74LS32

IC 74L$191

IC 74L$393

1¢ 74.802

IC 74L$139

IC 74.8374 IC 74LS161

IC 7418245 IC 74LS283 IC 74LS107

IC 74.8164

TC 74LS95

IC 74LSO9

1c 2114 DRAWING NUMBER 800-0163

REF DES.

C23

C14

C1-C13, C15-C22

XPI

u40

U9, U32, u42

U39 U20, U21, 035, U36, U48, U49, u54 u37

ulg, U4) u50

ulg, u51 ua7

ua, u38 U18-U17

uzz

u23

u46

u2, u13 U10-U12, U34, U52 ui4 u33

u53

u3

U6, U7, U44, U45

Ul, US u24-U31

Page 106

X-¥ CONTROL ASSEMBL Y-Cont inued DRAWING NUMBER 800-0163

qry ITEM NO. PART NO. REQD. DESCRIPTION REF DES,

31-35-0072 2 IC AN25LS14 us, U43 32 © 471-0123 3 Res 12K Ohm 1/2W 5% R1, R3, R5 330-471-0472 1 Res 4.7K Ohm 1/2W 5% RT 34471-0622 3 Res 6.2K Ohm 1/2W 5% R2, R4, RE 35 481-0006 6 Diode 1N914/1N4148 D1-D6 3b Z43-UUUZ 8 Socket 18 Pin XU24-XU31 37471-0471 1 Res 470 Ohm 1/2W 5% R8 38 471-0103 1 Res 10K Ohm 1/2W 5% Rg 39471-0332 1 Res 3.3K Ohm 1/2W 5% Ril 40 471-0512 1 Res 5.1K Ohm 1/2W 5% R10 41 482-0006 1 XSTR 2N4403 ql 42 482-0014 1 XSTR 2N4401 Q2

Page 107

800-0163 X-Y CONTROL ASSEMBLY

a ® pro = | Ol H Us 9 WOO Ud UU ae LooOOg 1 is ef

ae se | i)

Page 108

UNIVERSAL SOUND BOARD ASSEMBLY DRAWING NUMBER 800-0377

QTY ITEM_NO. PART NO. REQO. DESCRIPTION REF DES.

1 150-0087 2 Cap-E 4.7 f 25V ROL cl, C4 2 150-0090 1 Cap-E 33 f 25¥ RDL C60 3 150-0135 7 Cap-E 1 f 25V ROL C14, C15, C33- C36, C54 4 151-0002 9 Cap-CER 100 pf SOV C6-C8, C19-C24 5 154-0021 e Cap-CER 20 pf 50V cAl, CA2 6 151-0060 29 Cap .1 f 16V AX C3, C5, C10-Cl2, C18, C26-C31, €37-C40, C43- C-50, C57-C59, C61, C62 7 152-0011 3 Cap-F .15 f 50V C5i, C55, C56 152-0085 6 Cap-F .01 f 50V co, C13, C16, C17, C25, C32 9 152-0144 1 Cap-F .082 f 50V c53 10 170-0259 1 PC Board W 212-0081 1 Conn 4 Pin M RTG PLZD Pl 12 213-0001 2 Skt 24 Pin Dual INLN XU50, XU517 3 213-0002 2 Skt 18 Pin Dual INLN xu44, XU45

15 213-0005 1 Skt 40 Pin Dual INLN XU46 16 230-0037 1 XTAL 6.0 MHz Yl

7 280-0420 2 Card Ejector Snap On 18 313-0037 1 IC TLO81 vag 19 313-0038 13 IC TLO82 Ul, U3-U6, U9, u17-U23 20 314-0018 1 Ic 74LS00 U36

21 314-0055, 1 IC 7418244 u55 22 314-0060 1 IC 74LS20 u40 23 314-0062 2 IC 74874 U2, U38 24 314-0067 1 IC 74830 U59

Page 109

UNIVERSAL SOUND BOARD ASSEMBL Y-Cont inued

ITEM_NO.

4] PART NO.

314-0068

314-0075

314-0076 314-0085

314-0087

314-0099

314-0100

314-0104

314-0131

315-0035

315-0046

315-0059

315-0077

315-0079

315-0132

315-0133

470-0102

470-0103

470-0104 qry REQD.

Aww nm Ho BHM HO wR

~~ oO

VW DESCRIPTION

IC 741832

IC 7418393

1¢ 7418157 Ic 74814

IC 7418139

IC 74LS245

IC 74LS273

IC 74L$138

IC 74L$373

1C MM5837

IC 2114

IC 8253 IC 8035

IC CD4053

Ic A07524 IC eK x 8 Static RAM

Res 1K Ohm 1/4W 5%

Res 10K Ohm 1/4W 5%

Res 100K Ohm 1/4W 5% DRAWING NUMBER 800-0377

REF DES.

U35, U37, U39

U32, U33 U56-U58

U48

u10, ull

Use, Ub2 u54

u34

u60 u44, U45

U41-U43 u46

u7, U8, U15, u16, 30, U31 U12-U14, U24-U29 ub0, US) R23, R24, R30, R33, R53, R56, R59, R63

R20-R22, R27, R40, R41, R50- R52, R57, R58 R1, R7-R10, R12, R13, R15, R16, R18, R19, R25, R28, R29, R31, R32, RI4-R346, R38, R39, R42, R43, R45, R46, R48, R49, R54,

R55

Page 110

UNIVERSAL SOUND BOARD ASSEMBLY-Continued

QTY

ITEM_NO. PART NO. REQD.

44 470-0105 2

45 470-0124 ]

46 470-0222 2 47 470-0271 1 48 470-0272 2

AD 470-0333 4

50 470-0324 1

51 470-0562 3

52 470-0332 ] 53 482-0023 1

54 182-0054 1 $5 152-0076 1

56 212-0158 1

57 212-0159 1 DESCRIPTION

Res 1M ohm 1/4W 5% Res 120K Ohm 1/4W 5%

Res 2.2K Ohm 1/4W 5% Res 270 Onm 1/4W 5%

Res 2.7K Ohm 1/4W 5% Res 33K Ohm 1/AW 5H

Res 330K Mhm 1/4W 5% Res 5.6K Ohm 1/4W 5%

Res 3.3K Ohm 1/4W 5% XSTR 2N4093

Cap-F .001 f SOV Cap-F .1 f 50V Conn Header 8 Pos

Conn Jumper DRAWING NUMBER 800-0377

REF DES.

R2, R11

R6

R5, R60 R62

R64, RES RIA, R37, RAA, R61

R3

R17, R26, R47

R4 qi ca

C52

p2

Page 111

800-0377 UNIVERSAL SOUND BOARD ASSEMBLY

Page 112

G-80 POWER SUPPLY CHASSIS ASSEMBLY DRAWING NUMBER 800-0191

qry ITEM NO. PART NO. REQD. DESCRIPTION REF DCS.

1 530-0016 1 Heat Sink, G-80 Pwr Sup. 2 250-0460 1 Chassis Support 3 250-0461 1 Cover 4 800-0170 | PCB Assembly 5 253-0206 6 PCB Support, Threaded 6 281-0032-06 8 Thread Forming Screw, #6 Type B, 3/8 long

8 482-0104 1 Power Transistor TIP 141 313-0023 1 Negative 5 Volt Regulator 320TS 10 313-0014 1 Positive 12 Volt Regulator 340T12 W 313-0015 1 Negative 12 Volt Requlator 320T12 l2 482-0100 1 Power Transistor (Audio TIP 125 Amp) 13 482-0019 1 Power Transistor (Audio TIP 120 Amp )

16 420-0557 1 Fuse Decal 7 280-0117 1 Tab Rivet Male 1/4" 18 420-0575 1 Power Supply B Necal 19 281-0001-08 6 Pan Head Phillips Screw, 4-40x1/2" Lg 20 280-0341-00 6 Shoulder Washer, #4 21 310-0006-01 6 Transistor Insulator, T0-220 22 284-0001-00 6 Flat Washer #4 23 284-0031-00 6 Split Lock Washer #4 24 283~0021-00 6 Machine Hex Nut, 4-40 25 800-0243 ] G-80 Transistor Harness

Assembly PI

Page 113

G-80 POWER SUPPLY CHASSIS ASSEMBL Y-Cont inued DRAWING NUMBER 800-0191

qTy TTEM NG. PART NO. REQD. DESCRIPTION REF DES.

26 800-0244 1 G-80 Transistor Harness Assembly, P2 27 800-0245 1 G-80 Transistor Harness Assembly, P3 28 800-0246 1 G-80 Transistor Harness Assembly, P4 29 800-0247 1 G-80 Transistor Harness Assembly, Pb 30 800-0248 1 G-80 Transistor Harness Assembly, P6 31 310-000 7-01 1 Transistor Insulator "H", 10-218

Page 114

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 115

G-80 POWER SUPPLY PC ASSEMBLY DRAWING NUMBER 800-0170

Qqry ITEM NO. PART NO. REQD. DESCRIPTION REF DES.

1 150-0088 9 Electrolytic Capacitor, C5, C8, C10, C18, 10 uf, 25V Ci9, C23, C24, C26, ¢31 2 150-0092 1 Electrolytic Capacitor, Ci7 100 uf, 25V 3 150-0095 1 Electrolytic Capacitor, c30 3300 uf, 25V 4 150-0096 3 Electrolytic Capacitor, C€32-C34 6800 uf, 16V 5 150-0097 4 Electrolytic Capacitor, C15. C16. C27, C28

4700 uf, 25V 6 351-0002 1 Ceramic Capacitor, 100 pf, C9 50V 7 151-0007 1 Ceramic Capacitor, .005 uf, C20 TOOv 8 151-0011 4 Ceramic Capacitor, .0l uf, Czl, C22, C25, C29 50V 9 151-0012 3 Ceramic Capacitor, .1 uf, €2, C13, C14 SOV 10 151-0021 1 Ceramic Capacitor, 20 pf, c7 5ov Vy 170-0222 1 PC Board 12 212-0020 2 10-Pin Male Connector RTA 3 212-0081 2 4-Pin Male Connector RTA 14 313-0001 1 IC LM723 Dip ul 15 471-0011 1 Resistor, 10 Ohm, 1/2W 5% R2 16 471-0101 1 Resistor, 100 Ohm, 1/2 5% R32 7 471-0102 3 Resistor, 1K Ohm, 1/2W 5% RIO, R27, REO 18 471-0103 2 Resistor, 10K Ohm, 1/2 5% R6, R30 19 471-0104 1 Resistor, 100K Ohm, 1/2W 5% R22 20 471-0222 2 Resistor, 2.2K Ohm, 1/2 5% R21, R22

WW

Page 116

G-80 POWER SUPPLY PC ASSEMBLY-Cont inued

Qry ITEM NO. PART NO. REQD.

ral 471-0223 2 22 471-0332 1 23 471-0182 1

24 471-0681 1

25 473-05R0 1 26 473-00R2 2 27 475-0004 1 28 481-0002 2

29 481-0004 10 30 481-0006 3 31 482-0006 2 32 482-0014 2 33 514-0002 2 34 514-0003 8 35 514-0006 1 36 514-0008 1

37 800-0191 1

38 471-0220 1

39 471-0221 ] DESCRIPTION

Resistor, 22K Ohm, 1/2W 5% Resistor, 3.3K Ohm, 1/2W 5% Resistor, 1.8K Ohm, 1/2W 5% Resistor, 680 Ohm, 1/2W 5%

Resistor, .05 Ohm, 5W 3%

Resistor, «2 Ohm, 3W 5% Pot 1K Car PCMTV

Diode MR751 Diode MR501

Diode 1N914/1N4148 Transistor 2N4403

Transistor 2N4401

Fuse 3A Norm

Clip Fuse Mounting Fuse 1.5A Norm

Fuse 10A Slow Blow

Schematic Reference

Resistor, 22 Ohm, 1/2 5% Resistor, 220 Ohm, 1/2W 5% DRAWING NUMBER 800-0170

REF DES.

R5, R9 R28

R26

R7

R25

R14, RIS R31

010, DI2 06-D9, 011, 013-D17 D1, D4, 05 Qi, V7 Qe, U3 Fl, F2

F4

F3

R8

R33

Page 117

G-80 POWER SUPPLY PC ASSEMBLY 800-0170

a GL] a af, 2 ok ARE i hl =" ee TTT TT TTEETTOTT ® Bay @ Hy 6 : * > 5}

Page 118

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 119

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 120

D IO 7 62? QJ °

6s © + ° ba + oO 82 © t ° + 226 el £1 & REF ONLY Bg

Out? @we z " 8, Cl sau 2-@vue t 2 Gut 2@ve = Te 10 aut 3 ©ne 7 13 i;{ Ui | 74253893

tz 1 4 fe aT 74

ma Se es

A oo

ie

NEXT ASSY USED ON APPLICATION

Page 121

REVISIONS, ZONE | LTR DESCRIPTION ‘Date | APpRoveD ~] 866 SHT 1

FIRE D

THRUST THRULT

FIRE

g PLAYER 1 PLAYER =

LY

¢c

ua TEL Sit Le—

a Na XK a © S & ke

B

I TY | ‘CODE I PART OR I NOMENCLATURE [ [me nop IDENT IDENTIFYING NO- OR DESCRIPTION NO. PARTS LIST UNLESS OTHERWISE SPECIFIED [CONTRACT NO. DIMENSIONS ARE IN INCHES FTOLERANCES ARE: FRACTIONS DECALS ANGLES ve _ os San EAT. SINGLE PLAYER q CHECKED Gp GRICE [F562 CONTROL PANEL A [MECH J farce INTERFACE i fe SIZE] CODE IDENT NO TORAWING KO REV J prover C 800-0374 B 00 NOT SCALE DRAWING scae W246] [sneer oF 4 +

Page 122

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 123

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 124

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 125

J 4 3 2 1 FEVSIONS ca TEsonPron oar | aoe a BELEASED FFF [ese gol a ROW Bl ECN #528 CTC [ste Pipi CT ECN* GES cTe 2 wv 21 RA pi DLECNF G77A Cte fee a zw ® E | PER ECW # 978 MGA faves ee Pcéé HT f FOE 7 wae D PF

ao) a 20, PF

35 2) }+}-— RF

a a

PF

¢c

Sip st = D5 (SHT 6) i —____ Ha —__——4/a us 19} 15253 uy 2 D4 (SHT 6)

  • 2 13} ar ta B 220, a PF _ Lead L___ al > (sHT 6) he 220. {$$ [—_ Pe n iS]

[ee] es [echt | ed I [ BARTS Her Pueoc eR wae PT Gremlin industries, Ine. TOLERANCES ARE: San Bago, Californen 92ES FRACTIONS DECALS ANGLES : a Teens oa A lssrexx PRIN carrer noes tre Re [nro | CPU BOARD LES. earee ar [SIE EDGE TORT FO BRT FO REY is} 800-0107 F Te ae Pret [APPLICATION 5 ROT SEALE DRAWING ene wONET] Ten or 7 3 2 ] 1

Page 126

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 127

J 4 | 3 | 2 | 1 TEGO one ure] ‘DESCRIPTION [Sr [arrowed (eT ses tar FoR Guances lasts |

+5V AIS Al 20 le it G2 60-67 0-77 100-107 T9117 130-127 ie ko eo By

=

:

ur us ane ug ene 276 2716 1 “ a

ute api 220-227

a SY ed ed ed Cd ad Cod ead ed od SPRRARRARE pele ]-}.[J.[J1], ey DpPOMpsayg 210-297 S

tH

p= lelel[lole[ Jol).

GRUS(ECUMMGJUGOE: Ge OWEC uo Sms 7 1 4

= 200-207 2i0- 217 FIG lo7 730-237 240-247 a fi we Jeo Jeo Jeo deo jee ot caF RAAAB AAR us ur7 arte ure ero ule ote uso one 21), uae 6 TALS 7 isa 8 Is Ise [LELLELE ple] -ffulafale[~. Jeb I-LLLLEL

a +2 F UUs pM GOD FS a T

AP ARS Ale ALL Hid f

is |v fe Je fir [is Ja |s Saul V VV VVYVV Vie

tol is [a fia ta fs [rie ] 800-018) [LT

PP CNM aXXo Of O1 D2 P3 74 DE De DT

ome Ta OF TNoMENATC Tae] SS [wetttinthe _T ed I I

Po JBIMENsIONs ARE IN INCHES Gremlin Industries, ine. enacts Ark: Sun Oiege, Cabéernia 9223 FRACTIONS DECIMALS. ANGLES. = me = Bare AROS aan PANN Futter ya “4 lord 2716 EPROM BOARD i arr aa,

(NEXT ASSY USED_ON o 01 51 APPLICATION D0 ROT SCALE GRAWING fence wor? ] Paar ore i] 4 3 2 | [

Page 128

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 129

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 130

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 131

ay DEscRIEMOW [one [armnove [eco ey

a R=) 0

D

is 1 aa a Ema | w misot io 4 Fa

Cc

=

aim

  • B

v2 fatsre = gj ues jo ovuy = | 3s Oo i

@

[ae] [otis | Froud | [ Tare ter ene een meee | [TS ‘Gremlin Industries, ine. Eoaraties aoe cuts an Bioge, Catvernen 92193 ? ne Toms [one A pexseane PRR son DUONG __|3-Ker BY ee, Lae lad’ X-Y TIMING Aaa aie ata ial “SIZE [CODE IDENT NO./ORAWING NO, REV BA? eee o 800-0161 | . nanT A951 UD ON "APPLICATION DO_NOT SCALE DRAWING AE NONE] eee or 7 3 2 | 1

Page 132

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 133

J 4 3 2 1 REVISIONS zone [UR] DESCRIPTION [pare _[ arrnoven [ [eee ee ~

tr = ATOPF Sov, (a) 0 _ 208 } FL SOB D & 4 3 Ca “ wf 8 ay isio7 [2 ua io 3s toe uso 4 [any 4 43 5 ht EET Ey 30 tsoa ' vee I is) eh a> amie -—

  • war

<> rere c

cz raw 7 fa) maw « te fur Ga) vee aM wor ig) mux re

B

usec on z [uss 3 = = {us) Ta [usa)}* 4 —_—-___@ 76 3 o cop ! a

[ee] Se [ete e | SPE, i I : PARTS 1ST Barges ane m neve” || ST Gremlin Industries, Inc. FRACTIONS «DECIMALS ANGLES ‘San Biege, Cotiternia $22 : ae 2 PR aa A xe naive Som_w0n6 —_|o-¥-60) Poe Pease |ia-bo X-Y TIMING rare’ fool?" 5 a iE [CODE ERT WO [ORANG BOT T REV GA-EEViESBOEA D 800-0161 | - WOT Assi 50 On "APPLICATION DO NOT SCALE_ DRAWING scat HONE | [sneer 7 or 7 ; 4 3 2 | 1

Page 134

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 135

t 3 2 1 REVISIONS. Fe DESCRETION ae) 1 5 5 | [ste sett So (6-4-8) [Fe RON [;) tel re] 7 7 fe) la « + 3] naw 3] ram 3] am 7} ae 2) ana 2] un C30 1] uzs T) ues D if oo td C3 te ie 6 15; 1s at 3. 8, D io: 5 ht fepaye oGDGs 18 2 7 3 bd

15 |rauszeg S. ” Is, 5 s } um [6 aus |— 5 te te 8 7 (m0) 7 7 7 2 ee gre = + + Tp, efz 2 3 EY E i

  • MM zi} mM Zz) OR + 2 rT} 24 Ty alte 17] Ute 7] u2s 7) uae le a o 5: S rs 2 + cop [taj 8 8. 7 é io D lo. c |, 8 2 uw fie fae fu Jee Jalia moots a] US are [a ak 1 T 4] UB hs ba 7 i one ie o cor yn }

le—

B Paaeeaaa| o BEREK., 0 PERE Ks 5 7 eye. 8 = iszaa 45 £7] mse! +52] vase o tH) uzo zhu [ee un ft -_— Fy rary Ceqepee [yee = 8 + t 9 ash: Ss 244 H it 8 S[pepsye

iBemt_|__omnnnrne no. Se Desh ae] Sette] UTR I PARTS UST Shagant ane meses Gremlin Industries, ine. FRACTIONS DECIMALS ANGLES ‘San Pisge, entorornés 92107

  • Xx = ROWS Tae A xe RR SoM OuoN —_|\o-6-80 aver X-Y CONTROL

pe [CODE IDENT NO.TDRAMING NO. REV BO0- 3155 [700-005 \ 4 a tae [7090074 800.0163 | APPLICATION ‘DO NOT SCALE DRAWING nore] [sneer 5 FS | 1

Page 136

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 137

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 138

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 139

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 140

alule [ales fals|= Jen run &

ia

4053 WR 6 DL_02 0304 05 06 07 AE % Y ur ic

4053

x

u7y

[>

ee es

line! ~|c0] 0/5

Page 141

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 142

£300 L SOC tay sto le bs g te WE Vee GAO if,ce 2h. poe 4 Ay te Ae uss gue E e cud £832

; — sue i? 3 _———

p Ifo os cz or “6, ps ua_u ae (rae i 2) fia

DR? DRo

brs , DR? DRE LRI wet

Page 143

2 1 REVSONS zone [ure] DéscRITON To pate | arenoven: { [eters cary L

D

ys na — aR we Is a le G2A628G! U3F || Ble so 8 ‘a a v2 yi yal c

74251398

=

B

<i N nN Da) s & q

[ee] i [cole Bend | [ret amizaer Ths Se SES oor Gk ‘DATE = ~ A Saas UNIVERSAL SOUND BOARD

ree woe PROEET Ld 800-0377 a APPLICATION (00_NOT SCALE_DRAWING some ot eT Pesos t 4 3 2 ] 1

Page 144

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 145

1 4 | 3 2 1 1 jl P2 Pe REVIONS Tent] Tao davdlo IN“ >A <B> <>avpio our # (sheer ae

Re + zese : anaaagl R? a D

eo m1 +—it 2N4g0) 100 PF ‘az

as ee] $5 AIS BK aor 20 }— , RO RZ 22K en T FOR FUTURE USE 1 a | c2 | PL I our ; 4 ij 1 <> aupio ww #2 \ qe | | | 1 | \ fer c | {1 | (Our | 1our L-—_|4 | Ra | R22 680 | 2.2K | | Lt | ana4or Ri fee | 7 1 _ i | he I RI | teen | +5V 4A | | \ t

-5V IA ) B

——— tievia i = Te GND | a +—<S> \ S i} iS | 8 —_—_% -izv a I = P3. Li aa ae ee

Te woth] Se ORSERTON l [ Pais ust a a ae Gremlin industries, Ine, To swaurs San Dioge, ¢atiternis 92075 = a= + APPROVALS: DATE A JX AWN cTERAL CATTELL [2/1i/ay eects ee [nso] G-80 POWER SUPPLY SPener ap ser a TE OODE TDENT WO [ORAWTTE WO REV a > 800-0191 a APBLICATION BO_ROT GALE_ORAWING pene wOnE | Parse 3 t 4 3 2 | 1

Page 146

Model Numb« [— aut ape 3B

a a “Ei t EC

i i i i Hs i " i q fl ll ql i H i c =

Page 147

es r 35S OMERWSE SPECIFIED RESISTANCE tanta He ' prises STAND CONTIMRIING PURPOSE: oe pant VA REPLACE ALL COMPONENTS MARKED ‘SAFETY SYMBOL WITH IDENTICAL TYPE. i‘

I

is

' nveee t FS 2: —

00°4177-04

iber GO8-003

19” X-Y¥ Color Monitor 200-0025

Page 148

WE WELCOME YOUR COMMENTS!

Your comments and suggestions will assist us in improving the usefulness of our publications. They are an integral part of preparing for revisions of manuals and parts catalogs.

\f you have any technical questions about any SEGA/Gremlin game, are requesting additional publications, or have a suggestion about how we can make our publications more useful to you, drop us a line or use the handy form below. We value your input.

Comments:

Fill in if you wish a reply: Name. Firm, O Distributor Address OOperator City State Zip Oother

TS

Page 149

First Fold.

BUSINESS REPLY MAIL

FIRST CLASS PERMIT NO. 10129. SAN DIEGO, CALIFORNIA

POCTAGE WIL) RE Pam RV ANNRRCCEE

SEGA/GREMLIN 16250 Technology Drive San Diego, California 92127

Attn: Customer Service IT NO POSTAGE NECESSARY IF MAILED AN THE UNITED STATES

Second Fold

abpg sip adey

Page 150

SERVICE NOTE

EFFECT: tacyscan

NUMBER: 001

There have been some errors identified in the Tac/scan™ Owner's Manual (P/N 420-0795). Please correct your documentation as follows:

“At the top right-hawd worner of pages 40 tnrougn 44, correct the Drawing Number to read 700-0106-01, “At the top right-hand corner of pages 45 through 50, correct the Drawing Number to read 700-0106-00. 7On pages 40 and 46, please add this information to ITEM NO. 30 on both sheets:

iTEM NO. PART NO. QTY _REQ’D. DESCRIPTION 30, 253-0245-u0 1 CRT Mask -The two attached sheets contain part numbers for programmed IC's used on TAC/SCAN™ cpu and 2716 EPROM Boards. Please include them with your

Qwner's Manual.

A SS SSS SEGA Electronics, Inc. 16250 Technology Drive, San Diego, CA. 92127-1985 Toll-free technical assistance 1-800-854-1938 outside CA. 1-800-722-8576 inside CA.

Page 151

A3SY. 2716 PROM PCB DRAWING NUMBER 800-3269

ITEM_NO. PART NO. QTY. REQ'D OESCRIPTION REF. DESG.

1 316-1670-00 1 IC EPROM 2716 ul

316-1671-00 1 IC EPROM 2716 U2 316-1672-00 1 IC EPROM 2716 U3

316-1673-00 1 IC EPROM 2716 u4

316-1674-00 1 IC EPROM 2716 us

316-1675-00 1 Tt FPROM 2714 us 316-1676-00 1 IC EPROM 2716 U7 316-1677-00 1 IC EPROM 2716 U8 316-1678-00 1 TC EPROM 2716 ug 316-1679-00 1 IC EPROM 2716 uTO

316-1680-00 1 1C EPROM 2716 ull 316-1681-00 3 IC EPROM 2716 ul2

316-1682-00 1 IC EPROM 2716 u13

316-1683-00 1 IC EPROM 2716 ul4 316-1684-00 1 IC EPROM 2716 UIs 316-1685-00 1 TC EPROM 2716 U16 316-1686-00 1 IC EPROM 2716 Ul? 316-1687-00 1 IC EPROM 2716 ug

316-1688-00 1 IC EPROM 2716 ulg

316-1709-00 1 IC EPROM 2716 uzo

316-1710-00 1 IC EPROM 2716 u2t

2 800-0151-00 1 ASSY G-80 2716 PROM BOARD

Page 152

ASSY. CPU PCB DRAWING NUMBER 800-3268

ITEM_NO. PART NO. QTY. REQ'D DESCRIPTION REF. DESG.

1 316-1711-00 1 IC EPROM 2716 U25

2 315-0076-00 1 CHIP 315-0082 21

3 800-0107-00 1 ASSY. CPU BOARD

Page 153

EFFECT: tac/scan™ convert-a-pak

NUMBER: 002 11/24/82

It has been noted that a number of Tac/scaN™” CONVERT-A-PAK's (P/N 700-0107) have left the factory with two possible assembly problems. We recommend that you perform the following simple checks:

  • With the front electronics compartment door open, reach up on both sides and flip the contré] panel latches up. Swing the control panel up and out, revealing the control panel harness connector on your right. With each wire, one at a time, tug firmly (though NOT HARD), checking for loose pin crimps. In the event that any wires do pull out of the connector, an attempt can be made to salvage the pins; using a Molex pin extractor, remove the pin from the connector. Pry open the crimp, re-insert the wire, and re-crimp the pin onto the wire, If the pin cannot be saved, replacement Molex female pins (P/N 211-0042) are available from your distributor.
  • Facing an open G-80 card cage, note the red plastic connectors at the front edge of the various cards. This is an "insulstiondisplacement! type of connector, and the problem here is that the wires may not be inserted into the connector far enough to effect an electrical connection. Simply take any thin-bladed screwdriver (a "tweeker'' is ideal) and push the wires further

into the connector. This forces the wire between two metal

"blades", cutting the insulation and bringing the conductor into physical contact with that particular "pin-out".

ey SEGA Electronics, Inc., 16250 Technology Drive, San Diego, CA. 92127-1985 Toll-free technical assistance: 1-800-854-1938 outside CA. 1-800-722-8576 inside CA.

Page 154

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.