CATHODE RAY TOMES

Space Wars

Space Wars (Cinematronics, 1977) · Document · 35 pages · 6 sections · original scan

Page 1

SPACE WARS

THE CENTER OF ATTENTION

SERVIIGE ANN OW MEWS NUANIULALL

(714) 440-2933

Page 2

SPACE WARS SERVICE

AND

OWNER'S MANUAL

© COPYRIGHT 1978

CINEMATRONICS, INC,

Page 3

1.

3.

4a

5.

6.

7.

9.

10. CONTENTS

ContentS.cesccsececrcrcece

Introduction ....06

General Information ......

Vector Theory .ecsscoeseee

Technical Information ....

CPU Logic .scscceeees

Display cccccccsscces

Trouble Shooting Guide ...

Schematics .eeccssscrceoee

Parts List ,ceccescoesceee (suggested stock)

Warranty ceececvccccccccee

Return and Ordering Procedure sssssccsereceecs PAGE

ll

Page 4

INTRODUCTION

keKK

Dear Space Wars Owner:

This manual is provided to allow the owner of the Space Wars game and personnel assigned to service the game a greater understanding of its operation. It is hoped that the deeper understanding of your Space Wars game will aid in reducing any down time that may be encountered by providing better technical assistance and general information pertaining to upkeep and parts procedure.

Also contained within this manual can be found information pertaining to your Space Wars warranty, and trepair procedures for any defective assemblies under warranty.

Your Space Wars game is designed to provide you and your customers maximum return in both profits and enjoyment throughout the longevity of the game, Please take the time to read through this manual as it will help to keep your investment in good order.

Thank yous

i c SA

Frank Sola Service Department Cinematronics, Inc.

Page 5

GENERAL INFORMATION

Generally speaking, your Space Wars game is designed much

the same as conventional video games. The only major exception

to this is the fact that the Space Wars game is provided with an

alternate means of visual display: the patented Vectorbeam tm x

monitoring system.

The game is, however, built of the same basic building blocks

as any other video game.

The Power Supply which provides all necessary voltages to

power each separate electronics assembly as well as all lighting

required throughout the game. It must be noted that there are

“on board" regulators provided for certain voltages needed on both

the audio logic board and the display printed circuit board. The

plus five (+5) volts d.c. regulated voltage for the central processing

logic board (CPU) is developed totally on the power supply. This

same voltage is used where needed on the audio logic board and also

the display printed circuit board.

The Central Processing Unit, contains circuitry to strobe and

interpret all input functions including the player control panel

switches and all coin and credit information and to create all the

digital signals used in providing the visual display, It also contains

all the software (1.e., machine language and game personality memory)

needed to control the game operation and to generate the proper vectors

needed to display.

  • "Vectorbeam *™" 1g Cinematronics service mark for video game repair and educational services.
Page 6

In fact, the CPU logic board contains a great portion of the

vector generating system, which also includes the display unit. The

CPU logic board also controls the switching (electrically) of the audio

printed circuit board.

The Audio Board, as in many other video games, is comprised of a

noise generator and the associated wave shaping circuits as well as a

number of amplifiers. The various audio tones are simply switches to the

output amplifier stages on command from the CPU logic board.

The Vectorbeam *™ * Display Electronics is the final form of

interpretation of the CPU's calculations. The CPU logic informs the

display electronics unit of information regarding line length and line

placement on the CRT. This is accomplished with two twelve-bit words,

one each for horizontal and vertical deflection, and a number of other

controlling signals for the cathode drive circuit and switching in the

deflection circuits.

The major difference between the vector generator and raster scan

type monitors is the means by which the cathode beam is directed (deflection)

across the screen.

In the raster scan types of display the electron beam from the

cathode to the anode of the CRT is constantly deflected (scanned) across

the face of the CRT in a series of horizontal lines that trace from the

upper portion of the screen to the bottom in a syncronous pattern, Vertical

information is added, also syncronous with the horizontal, forming a matrix-

type pattern of mathematically possible illumination points on the CRT. If

the cathode current is increased at these points on the screen in matrix-type

patterns (similar to placing dots on a piece of graph paper where the lines

intersect) coherent video in the form of shapes and alpha-numerics to form

the game backgrounds can be displayed.

Page 7

The vector generator takes a slightly different approach to cathode

beam deflection. The results are a much higher degree of resolution and

much smoother motion across the screen, as well as the ability to draw true

curved lines on the screen. Rather than using a constantly scanning cathode

beam, the beam is directed only to points of eventual illumination, using

a vectoring form of programming rather than a matrix approach. Basically,

the cathode beam is directed between two determined points, and illuminates

the entire path of phosphores between these two points, unless blanked by

stopping cathode current (i.e.: when the beam moves from one star to another

on your screen). The ability to illuminate (1.) direction desired, (which

is not possible in a raster scan system) creates a much higher degree of

resolution than can be found in a raster scan system, while at the same time

creating a much greater number of angle possiblities. This is also supported

by the ability to accomodate two twelve-bit words of information, twelve

each for vertical and horizontal deflection, and the fact that there is no

background illumination from a constantly scanning beam when brightness is

turned up. The higher degree of resolution combines with the totally

blackened background creating an appearance of depth not found in a raster

sean system,

Another major design difference is the fact that no sync. signals

are needed to produce vectors on the CRT, This greatly simplifies the

hardware design of the system, and therefore the understanding of the

theory of operation, of the CPU logic as well as the display electronics.

(1.) The entire path of phosphors crossed by the electron beam, in any

Page 8

VECTOR THEORY

In order to understand the basic concept behind a vector

generated display, it is important to have a basic knowledge of vector

theory.

As mentioned in the general information section of this manual, the

raster scan display uses a matrix type display pattern, A graphical

representation of a matrix is shown below in Figure A.

HORIZONTAL

Cooeee} L VERTICAL For example, to produce a line on the CRT with a matrix-type pattern,

the appropriate intersection points of horizontal and vertical lines are

illuminated. The calculations which select these points are made on the

logic board, and converted into video information for the monitor to digest.

Although there are spaces between the illuminated points, the illusion of a

solid line is made by your eyes, and the resolution is determined by the number

of available horizontal and vertical lines in the system, and the speed of

the sweep.

Page 9

In the vector display system, there are no horizontal and vertical

lines (no sweep) or sync. a line created using a vector system as shown in

4 TCH Figure B., below.

Co

+—t am a

ea t

2K, -by)| “f T

| im LI] {TE H

A line is drawn by programming a beginning and ending point of the line

to be drawn, and forcing the cathode beam to travel between these two points,

illuminating the entire path of phosphorus on the CRI. The angle of the line,

the position of the line, and the length of the line are determined simultaneously,

and simply, by selecting the proper voltage levels for the beginning and ending

points of the line.

Page 10

The end result of using the vector generator is an immensely increased

number of programable point, which is in direct proportion to the word size

and the capabilities of the DAC-80 (i.e., greater esolution, definition and

smoother motion using minimum of hardware).

Page 11

CPU LOGIC THEORY

The CPU (central processing unit) logic board used in Space Wars

is not a micro-processor, but rather a dedicated TTL processor, much like

a mini-computer would use,

The primary advantages of using a dedicated processor versus a micro-

processor are that the CPU logic is much faster electroncially, and it has

the ability to use a word length designed for a specific task.

The primary disadvantages from a service standpoint, are that the

system is heavily software controlled with it's own machine language and

op-codes and there are a number of "loops'"' within the signal paths that are

virtually impossible to trouble-shoot using ordinary means and techniques.

The speed of the signals occuring on the CPU logic board are also a drawback

of sorts, since very fast scopes must be used to analyze the signals.

Because of the difficulty encountered when service is necessary, a

factory test fixture, a Hewlett Packard signature analyzer (model 5004A)

and a specially prepared set of schematics must be used to repair the board.

This trouble-shooting system has been designed to the point where virtually

anyone with a minimum of electronics background is able to repair the CPU

logic board,

There are, however, a few areas of the CPU logic board that should be

understood, as they have a direct relationship with the display electronics,

and also because there is not much difficulty in trouble-shooting these areas

using conventional methods.

These areas are the IO devices between the CPU logic and monitor, the

IO device between the CPU logic and the audio printed circuit board, and the

reset circuit which performs self-test functions on the CPU logic board.

There are six IO devices between the CPU logic board and the monitor.

Page 12

Three of these devices are 7418377, M2, P2, S2, latches, which provide

the two twelve-bit words to the DAC-80's. The inputs to these latches eminate

from six 74L8194's (M4, P4, S5, N4, R4, T4) which are part of the primary and

secondary accumulators.

One I0 device is a 74LS32, 2 input And Gate, at location J2, Pin 3 output

provides the "intensity" signals to U7 (7406) on the display board, Pin 11 output

provides the "brightness" signal to U7 of the display board, As mentioned before,

these signals control the various intensity levels of the objects on the CRT, as

well as the blanking of CRT cathode current.

The final two IO devices found on the CPU logic board, that provide control

signals to the display board, control the LF 13310 analog switch (U1) on the display

board. These devices are found at locations H8, Pin 13 and G8 Pin 5, ("initial

position" and "live drawing" respectively).

The IO device that is found at location F2 on the CPU logic board (74LS259)

is the switching control output to the audio printed circuit board. Outputs

4,5,6,7,9, and 12 provide the two TL 182 switches on the audio board unit command

signals. Output 10 is used in the coin control circuit on the CPU logic board,

and output Pin 11 is used in the brightness control circuit.

Considering the fact that all of these devices mentioned are direct I0

paths between the game's sub-assemblies, it is generally good trouble-shooting

practice to check these IO devices on both assemblies if a problem is felt to be

located in one of the two circuits, For example, if the TL182 switch on the audio

printed circuit board were to fail, it could, not most likely would, cause the

74LS259 (F2) on the CPU logic board to fail also. If the TL 182 on the audio

board is replaced, and the 74LS359 is not checked, there is a good possibility

that the new TL182 will also fail, caused by the 74LS259 which was damaged

originally. This same situation could occur between any two I0 devices found

in a problem area, or any board.

Page 13

This is accomplished by the two twelve-bit codes (words) applied

to the DAC~80's on the display board. The DAC-80 will produce a different

voltage level at its output for each possible combination of input levels

(of which there are 4128 possibilities for each 12 bit word.)

It is also important to remember the function of the LF 1331D (V-2)

analog switch and its output RC network (see monitor theory). Because we

are dealing with reactive components in C101 and C201 on the display board,

the charging voltages found are non-linear by nature, (See Figure C., below).

Therefore, when a line appears on the CRT, it is actually only part

(section A-B, Figure C) of the entire path taken between the beginning and

ending points of the vector (C-D). The section of A-B is chosen as the most

linear portion of the charge curve, and illuminated

Sections C~A and B-D are blanked at the cathode, and points A and B chosen

by controlling the analog switch (V-1) on the display board, Again, these

calculations are all performed on the CPU logic board.

Page 14

The final area on the CPU logic board to consider is the reset circuit.

If a failure on the CPU logic board occurs, in any of approximately 90% of the

signals present on the board, a reset condition will occur. This reset condition

will "shut down" the CPU logic and prevent any information from reaching the

DAC-80 inputs of the display board, If this condition occurs, the two 25V

circuit breakers (or fuses) will let go due to the saturation of the four output

transistors in the deflection circuits on the display board, It is therefore

essential to determine, if thease breakers have tripped, whether the reset

condition exists on the CPU logic board since the problem will appear at first

sight to be in the monitor, The reset signal (actually reset) is found at C8 Pin

5 (74L8107) on the CPU logic board, It is necessary to use a logic probe with

a very fast response (faster than 20 Nano seconds) or an oscilloscope with a

horizontal sweep of at least 100 MHZ in order to see the reset signal which is

a steady state high when the CPU logic board is functioning properly, and pulse

is low or stays low when the CPU loigce board fails. It is also important to

note that there are only a few controlling signals that will cause a reset to

occur, (1.e., power up reset, cold start, etc.) By determining which of these

signals causes a reset to occur, the section of the CPU logic board that has

the actual failure can be isolated. This can be a very helpful tool in trying

to isolate a problem on the CPU logic board,

Page 15

VECTORBEAM MONITOR OPERATION

t™ monitor can be divided into two basic sections. The vectorbeam

One section is the deflection amplifiers, and the other section is the high

voltage and cathode drive circuit.

The deflection amplifier can be further divided into two indentical

channels: one for vertical deflection, and one for horizontal deflection. We

will describe the operation of only one channel (vertical) and the same theory

of operation will also hold true for the horizontal section,

Digital information, in the form of a twelve-bit word, is applied to

the input of the DAC-80 digital to analog converter (U101) on pins one through

twelve. The most significant bit (MSB) is applied to pin one, and the least

significant bit is applied to pin twelve. The DAC-80 makes the necessary

¢ onversion from digital signals to analog signals which are outputted as

analog voltage signals on Pin fifteen (which is proportional in level depending

on the input word applied), The result is a positive and negative voltage signal

about its reference voltage (remember, there is no "sync" signal present, and

the signal is not true video as seen in raster scan monitors),

From the DAC-80 the analog signal is then sent to a high-speed analog

switch, (U1). The analog switch has two parallel inputs for the display signal,

and two controlling inputs which select one of two outputs from the switch,

At the outputs is found an R.C. network, which is used to create line length

and line position on the screen,

Output fifteen from the switch routes the analog signal through a 5K

potentiometer (R102), an 11k resistor, (R103) and to the input of U102 op-amp.

The time constant developed by these two resistors and the capacitor (C101)

determine the length of the vector line seen on the screen. Adjusting of the

potentiometer will adjust the length of the vertical lines seen on the screen.

Page 16

Output ten from the analog switch routes the signal directly to the

input of U102 op-amp, and the resulting time constant of the op-amp input

impedence and the capacitor C101 determines the position on the screen of the

vector line.

Op Amp, U102, serves a dual purpose: one, it acts as a buffer between

the deflection amplifiers and the analog switch; and two, it acts as an "edge

gain" amplifier (i.e., height).

At the output of U102, there is a resistor amp, diode network consisting

of R1O5-R110, and CR101 - CR104. This resistor diode network is used to compensate

for the non-linear characteristics of the CRT near the edges of the screen. If

this circuit were not used, any object displayed on the screen would increase

in size as it moved closed to the edges of the screen. Also contained in the

circuit is a potentiometer (R109), which adjust the height of the pictures.

From the wiper of R109, the signal proceeds to Q101, which is the first

stage of deflection amplification, Q103 is an emitter coupled with Q101 to

provide a degenerative feedback loop from the yoke. Q102 is used to provide

a constant current source to both emitters.

At this point, the deflection circuit can again be divided into two

identical circuits. One circuit, which controls the lower half of the screen,

is comprised of Q104, Q106, Q108, and Q110. The other circuit, which controls

the upper half of the screen is comprised of Q105, Q107, Q109, and Ql11. **

Q104, Q108 and Q110 are three stages of amplification, while Q106 is

used as current limiting protection for Q108 and Q110. The same holds true

for the other configuration of Q105, Q107, Q109 and Q111. R124 through R129 are

used as a current divider network for the yoke,

% In the horizontal section of the deflection amplifier, Q204, Q206, Q208, and

Q210 control the left hand side of the screen, and Q205, Q207, Q209, and Q211 control

the right hand side of the screen. By dividing the screen in this manner, four

quadrants of deflection area have been developed (see vector theory chapter.)

Page 17

R122, R123, and C102 form a RC network, which compensates for any CEMF

that may develop by the expanding and collapsing of the deflection coil's electro-

magnetic field,

The high voltage and cathode circuitry is the second section of the monitor.

This section also contains the necessary voltage regulation to power the IC's located

on the display board as well as develop the high voltage.

U4 and U6 provide plus 15V and minus 1L5V respectively to power the DAC-80's

and the TLO81 op-amps on the display board.

U3 and U5 provide plus 18V and minus 18V used in the high voltage transformer

(T-1) and oscillator (the oscillator circuit is necessary because there is no

horizontal sync. used to develop the high voltage pulses.) The oscillator circuit

is comprised of primary windings, Q4 and associated discreet components.

The high voltage 18KV is developed by Tl secondary windings, the high

voltage tripler, and the focus circuitry. The potentiometer, R16, is used to adjust

the focus of the cathode beam.

One of the secondary windings of Tl develops the necessary cathode voltage,

which when measured at the cathode of CR6 should read 88VDC. The cathode circuitry

in the vectorbeam ™™ monitor is comprised of U7, a 7406 IC used for buffering logic

signals which control brightness and blanking. It also contains the transistors, Ql,

and Q2, and Q3, and then associated discreet components.

Q1, and the first gate of U7 control the brightness of the cathode signals

upon command of the CPU logic board. Q3 and the second gate of U7 control the

intensity (blanking) of the cathode signals, also upon command of the CPU board.

Q2 is used as a power failure protection for the cathode circuit in the event of

a loss of 25V power supply voltage. This protection aids in avoiding phosphor

burning on the CRT, R111 is the brightness potentiometer, which adjusts the

amplitude of the negative spikes used for brightness and intensification.

Page 18

TROUBLE SHOOTING HINTS

Read carefully before servicing game, Because of a number of design criteria in your Space Wars game, a problem that arises will generally cause one or both of the twenty five (25) volt fuses or breakers in the power supply to blow. When this occurs, the following procedures will aid in locating the fault assembly. It is important that this procedure be followed in the order in which it is written!

  • Unplug the game and short or meter the two filter capacitors found in the power supply. These are the two 20,000 micro-fared capacitors mounted near the transformer. They will maintain a charge when the fuse(s) are blown.
  • Replace the fuse(s) with MDL-3 Fuses.
  • Disconnect the Molex plug and the ribbon connector from the monitor.
  • Plvg in the game again and observe the fuses.

5, If the fuses remain in tact, place a credit on the game.

  • Start a game as if you were going to play, and listen for the game sounds,
  • If the sounds of the game (acceleration and fire) are present, the problem is in the monitor. If the sounds are not present, or if they are distorted, the problem generally is in the CPU logic board.

The reasoning behind this procedure is that if a failure occurs, in the CPU logic board, it will enter a "constant reset" mode, When the CPU logic board is in this mode of operation, or when there is a lack of computer information at the monitor input (i.e., disconnected a faulty ribbon cable), the monitor will automatically deflect the electron beam off the screen to protect the phosphors in the CRI. When this occurs, the monitor deflection amplifiers will enter a current limiting state and eventually cause the fuses to blow.

For further troubleshooting procedures, use the flow chart provided.

NOTE: It is important to follow steps one and two every time a fuse blows, to protect yourself from electrical shock, and also to protect the game from further damage.
Page 19

Yes TROUBLE SHOOTING FLOW CHART

Replace

Fuses

Unplug Monitor

Replace Fuses

Plug in Game Paplug Audio Repatr or

eplace Fuses Blown? Fuses Blown? Audio Board

Monitor Place Credit Replace Fuses Replace or

+5VDC on on Game Unplug CPU logic Repase ti

CPU board 9 Fuses Blown ogic +5VDC? Accept Credit?

Replace or Repair Power supply Start Game

Game Sounds?

Replace or

Repair Monitor Disconnect CPU Logic Monitor & &SVDC +SDVC?

Page 20

Due to the fact that: the vectorbeam SUGGESTED PARTS FOR STOCK

tm system is a new type of display

technology, there are a number of components used which may have limited

availability from your local parts suppliers. It is suggested that the following

list of parts be purchased from Cinematronics in the event servicing of your game

becomes necessary:

1.

2.

3.

5.

6.

7.

8.

9.

10.

1.

12. TL182 - Analog Switch

TLO81 - Op Amp

7918 - Regulator IC

7915 - Regulator IC

7818 - Regulator IC

7815 - Regulator IC

LF 1331D - High speed analog switch

DAC-80 Digital to Analog Convertor **

7448259 - IC (Texas Instruments only)

74LS32 - IC

Set D-ROMS (1-6)

Masked ROMS

Note: Contact factory for current prices
Page 21

WARRANTY FOR SPACE WARS

Cinematronics, Inc. warrants the goods to be free from defects in materials and workmanship under normal use and service for a period of (12) twelve months from the date of delivery on all parts except switches, potentiometers, buttons, fuses and lights, for which the warranty period is of ninty (90) days from the date of delivery. Cinematronics makes no representation or warranties concerning the goods whether express or implied by operation of law or otherwise, including those of merchantability or fitness for any particular purpose, or with respect of patent infringement, except as may be specifically made herein, to the repair or replacement of such parts which have been returned to Cinematronics plant at purchaser's expense and which examination shall disclose to Cinematronics satisfaction to have been so defective and to be the shipment of such repaired or replacement parts to the purchaser F.0.B, the shipper point.

This warranty does not apply to any Cinematronics product which has been altered or repaired by unauthorized personal or service facilities or any products which have had the unit serial number altered or removed.

Upon acceptance of the goods, the purchaser agrees to assume all liabilities for damage and/or bodily injury by the purchaser or any other c laims arising from the use or service of the goods by any person. Purchaser further agrees to idemnify Cinematronics, Inc. from any Liability, claim, cause of action or litigation resulting from the use or misuse of the goods by any person,

Page 22

RETURN AND ORDERING PROCEDURES

When it becomes necessary to return items to the factory for repair or replacement, or to order parts from the factory, the following procedure must be used:

  • All items returned must be accompanied by a credit memo which includes the items returned, the serial number of the unit from which they came, and whether the units are for credit against advance replacements or for repair or replacement and return,
  • When the items are for credit against advance replacement, reference must be made to the Cinematronics invoice that was received with the advance replacement item(s).
  • All items and/or parts ordered from Cinematronics, whether in or out of warranty, must be placed with a Distributors purchase order, either by mail or verbally by telephone.
  • Advance replacement items may be obtained from the factory, when available, using the same procedure as when ordering parts.
  • All items received as advance replacements will after a period of thirty (30) days, become customer property, and applicable charges and prices will be applied, if Cinematronics, Inc. has not received the defective units to credit against the original invoice(s).
  • In all situations convered above, and in all other situations, the warranty offered by Cinematronics, is applicable, and should be fully understood.
Page 23

OPERATORS ADJUSTMENT OF

SPACE WARS

The Cinematronics Space Wars video game using the patented vectorbeam tm

monitor has three adjustments inside the cabinet which can be set by the

operator,

  • Sound effects volume (see SOUND BOARD DRAWING: FIGURE 3)
  • Display intensity (see MONITOR CHASSIS LAYOUT: FIGURE 2)
  • Game time per coin adjustments (see LOGIC BOARD LAYOUT: Figure 4)
NOTE: All other adjustments inside the game cabinet are factory adjustments

to be reset if necessary by authorized personnel only. Incorrect adjustments

may permanently damage the machine.

FUSES: The Space Wars game has three fuses located on the power supply chassis.

Replace blown fuses with 3 AMP slow blow fuses.

WARNING}

DO NOT CONNECT OR DISCONNECT WIRES OR CABLES INSIDE THE MACHINE WITH THE POWER

ON. DAMAGE WILL OCCUR AND WARRANTY WILL BE VOID.

Page 24

VECTORREAM™" MONITOR f igre 2

BRriGwrnv ess COnwrTRasa

Sequce 3

LOGIC BOARD

OOU QO000000000 0000 OO OO00D C000 0000000 OOOO oo0 sooo NOo000oD coccoonnd Coo000o0 Ooudooo0 Nodooocog oo0o0o0000 Fryere 4 ‘ GAMES TIME: PER COIN [E] !:00 F.] 1:30 al 2:00 fe] 345

Page 25

LAMP

SPEAKER

vecrTeraean™ Man rar

KFrSonhD PANEL

PLAYS® ConT ech PANEL AUDIO BoaRD

CorNw Deore

POWER Svreee.y LoGic Board

corvw Bax

ew we ee ee oe.

SPACE WARS

(caBenéEr REAR view)

Page 26

290827

BEConary | 4 sTRosE

en

TeLsisl B " a cy Tausist

a RewsToR is RESISTOR Pre 1 Te PACK ay cw 4 2 4

[sudst dst,]si,]si,|sts154. la dor.dpralon Lpredpreden ber we fn @ : oops ie Aue tnrvrs! cone races 3 med 13500

Prin) ara D coumren

a0 in o> aneas2

4 thE? : af Os)

ma (ax) {7 PULL UP RESISTOR TO +5

7-K FLIP FLO ARE T4LSIOT VNLESS NOTED

in 2ort aneeT ions

Page 27

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 28

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 29

HM T0083 DeROMH Ave) Few) Trad one)

Lone ree Ave p93 (9) Lens enon fom imib A) warren aed ERATE TEEFER ASD wat (3,9) Tae area CY se wmire wth) ware axe Chi)

oss (40 prow (2,4) ERAT (4) wone (4) Loon ave (4) veri (4), a 2]

2075 weer gorse

Page 30

pRaweiwe,

Tasos ne Ne ene Lint Done

wane Tek

Pea Teen Aon

yausies Pe

Pay | PAR PRL [Phe Shy 15h, | SM | Sao May [Pe 1 Mag Ap 1504 +. | a

TNLINT MA

2ovs sneer Sor Ss

Page 31

v 1ouUe 9e-oe-1 NI8V) SYVM 3DdvdS ™ INOY| $9 WWAINID el ee ee

Frmuvages, Rereto Neretisn ©

; woeTS or ae te

Rete we seve oe wa ty 28 towne :

one se ae segre we awe erty ied enw ewes Kaeat uname

Page 32

herr som OW <——~~ ecw ise > SPEAKER

MOTE! Ting REsiswe [Lh tine comme 8 re pomer O Meter Commscren 9 Few So hsage s20r Geet fe sash ee 10 p88

Es Os. 77

Page 33

th CINEMA RONICS, INC. Tivem: DISMAY REECTAOMIES

& # Es r te

et aan AMMAR 1

Page 34

ALL CAPACITOR VALUSS ARE 1B MICROFARDS ALL ARISTON VALVES ARE 1m ObMS euEESS OTHER Wisk NeTED MeTS: © Arte THRU AILS ANB AEZOTHAU ALS ARE ComPEseD OF

‘Seu 2:20 \w agsisrena © THESE fowsD TAAMNSTERS ARE ComTsD congaT sives WG ARL SSPRATH FAR THE CC. F04hO (Ou ud tin) @ THESE ARE sen CODNECTiON famTs On THE RC. 66480 COMEMAT Oucs, inc. Titee; DismLat seecTAOMICS SCHEMATIC. See |" 207 [MA

Page 35

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.