Hit the Ice Kit (16-30203-101 Dec 1990)
Hit the Ice (US) (Taito Corporation (Williams license), 1990) · Manual · 43 pages · 29 sections · original scan
KIT MANUAL
OPERATIONS MANUAL
including:
Game Operation & Adjustment Game Testing & Problem Diagnosis Parts Information Reference Diagrams & Schematics
WILLIAMS ELECTRONICS GAMES, INC. 3401 N. Califomia Avenue Chicago, I. 60618 December 1990 16-30203-101
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Table of Contents
Section 1: Kit Installation, Operation & Troubleshooting SAPO... ec cessecsesneetesessesscseseesuecesessnsseeesesesaeeaessnnsseesieasecescgetsessneesesteesesenesnees Conversion instructions
Cabinet Modificatior Control Panel Modification: Installing PC Boards into a JAMMA Game Cabinet Installing PC Boards into a NON-JAMMA Game Cabinet. Game Features Starting-up.... Player Controls. Typical Contro! Panel Layout. Game Operation- Control Switches. dati ieeasinwicd snntecayriceen aiacTiae sacs IO Game Adjustments and Diagnostics Rules & General Information. DIP Switch Table. Troubleshooting
Section 2: Diagrams & Schematics
Coin Switch & Meter JAMMA Chait....... Cabinet Wiring Diagram: Control Panel Template Diagram(s|
COPYRIGHT© 1990 WILLIAMS ELECTRONICS GAMES, INC. ALL RIGHTS RESERVED
NOTES:
HIT THE ICE KIT
SECTION ONE
Installation & Operation |
Safety Notices
The following safety hints apply to allkit operators and service personnel. Specific warnings and cautions will be found throughout this manual where they apply. We recommend that you read this page, and also all of Section 1, before preparing your kit for play.
NOTICE: SALVAGED PARTS Parts salvaged from old games are required to complete your kit. These salvaged parts must operate perfectly: otherwise, the converted game cannot perform properly or safely. Always repair circuit board malfunctions and cabinet damage before conversion Is attempted.
NOTICE: POWER SUPPLY Be sure the power supply from your old game is capable of +5V dc at 5A ,~8V de at 1A and +12V at 1A. These operating voltages are necessary for your kit. Your power supply must be FCC approved.
NOTICE: MONITOR This kit is not intended for use with X-Y monitors. Suitable monitors have horizontally mounted CRYs and raster electronics with inputs for red, green and blue video, as well as composite Negative Sync inputs,
NOTICE: COIN MECHANISM Be sure to clean and lubricate your old coin mechanisms. Servicing them is crucial to your game's earning potential and operation.
NOTICE: COIN METERS Coin meters are not provided with this kit. Wiring information is provided as a convenience to the operator.
NOTICE: SERVICING, INSTALLING Always turn your game OFF and unplug it before attempting to service or Install your kit.
PROPERLY ATTACH ALL CONNECTORS. Be sure that the connectors on each printed circuit board (PCB) are properly connected. Ifthey do notslip on easily, do not force them. A reversed connector may damage your kit and void the worranty. All connectors are keyed to fit specific pins on each board.
Conversion Procedure
Inspection Unpack the materials from the carton and inspect for obvious signs of damage. Use this checklist to be sure your kit is complete.
Part No. ltem Quantity
| () C-9241-1 | Button Assy. Biue | 2 |
| () C-9241-4 | Button Assy. Red | 2 |
| () C-9241-5 | Button Assy White | 8 |
| () H-14272 | Player 3/4 Cable | 1 |
| () 03-6047-2 | Spacer 3/8 | 4 |
| () 16-30203-101 | Manual | 1 |
| () 16-9191 | Template Controls | 1 |
| () 16-9191-1 | Player 2 Cntr. Pni. Template | 1 |
| () 16-9191-2 | Player 3 Cntr. Pn. Template | 1 |
| () 16-9191-3 | Player 4 Cnirl. Pai. Template | 1 |
| () 20-9222 | Palnut 5/8 | 12 |
| () 20-9319-1 | 8 Way Wico Joystick-Red | 2 |
| () 20-9319-9 | 8 Way Wico Joystick- Blue | 2 |
| () 20-9457 | Button Holder w/Switch | 12 |
| ( 31-1480-30203 | Marquee Kit | 1 |
| () 31-1482-30203 | Decal Set Kit | 2 |
() 31-1612-30203 Control Panel Kit () 4308-01123-20B — Carg. Bolt 8-32x1-1/4 () §901-12734-00 CPU Assy. Hit The Ice © Assorted Hardware
Recommended Tools and Supplies () black semi-gloss paint Q electric drill Q electric screwdriver () grease pencil or marker hex driver () 180 grit sandpaper or electric sander Q pliers Q razor knife () soldering iron and solder () wire cutters Q black electrical tape () quick-hardening wood putty
1-3
Cabinet Modifications
Fill in gouges with a good quick-hardening wood putty. Sand cabinet and wipe it clean.
Repaint the cabinet with black semi-gloss paint (Games wood grain sides: remove the old decals and clean the glue residue from the old decal before painting). Allow paint to dry completely.
Pencil a line roughly at the top of the old graphic. Lightly moisten the cabinet with soapy water. Apply the decat starting at the top and working down. After the decal is in place, use a piece of the foam packaging as a squee gee and smooth the decal down, taking care to squeeze out the air bubbles. If you miss an air bubble, pop it with razor blade or a pin and burnish it down. Allow 12 hours for the adhesive in the decals to set. Remove masking.
Check the HIT THE ICE KIT for an FCC sticker and apply it over the existing sticker on the cabinet. When Williams ships a game. it is in compliance with FCC regulations. Your sticker is proof. If the sticker is missing or damaged, legal repercussions to the owner or distributor ofthe game may result. If your game kit does not contain an FCC. sticker, call Williams Electronics Games, Inc. immediately.
Apply the Instructions (Card or Decals) to the CRT viewing glass.
Control Panel Modifications
lL Remove the control panel buttons and joysticks and remove the old vinyl covering.
Place the template onthe control panel and use it to help you design your contro! panel. You will need to use the appropriate Mounting Template(s) for each player. There are (4) templates included in the set. For a 4 player kit simply layout each template as shown on the following page. Please note alternate the layout for a 2 player kit as shown on the following page.
1-5
4- PLAYER CONVERSION KIT
tm. BARE
a parege | | : 7 apapey aaa | | & 3 1] a «3 | 7 ;
2- PLAYER CONVERSION KIT
- Drill holes as needed for the joysticks and buttons. Plug previous holes with wood blocks, putty, cardboard or epoxy. File the new holes smooth.
4, Carefully remove the backing on the vinyl control panel overlay (user provided, not included in kit). Place the overlay on top of the control panel. Prevent air bubbles from getting under the vinyl overlay.
- a) After the overlay is on securely , use a razor knife to cut holes for the buttons and joysticks.
- Position the stickers around the appropriate button locations. Refer to the Typical Control Panel Layout diagram on the previous page for suggested button and joystick locations.
- Peel the backing from the adhesive on the clear protective overlay. Position the overlay so that it covers the stickers and press it into place. Use a razor knife to cut holes for the joystick and buttons.
- Tomount the pushbuttons and button-holder/switch to the control panel, push the threaded end of the pushbutton through the control panel from the top so that the threads extend through the back of the control panel. Then, take the white plastic button holder/ switch and place it over the pushbutton threads so that the threads extend through the hole in the holder. The blade switch must point toward the back of the cabinet and face you. Secure into place with a palnut. Repeat for all of the pusbutton switches.
The joystick must be disassembled before mounting it to the control panel.
1-6
Installing the PC Boards and Wiring into aJAMMA Game Cabinet
1, Disconnect and remove the existing video board in the JAMMA Game Cabinet.
- Mount the HIT THE ICE KIT video board inside the JAMMA
- If you choose to use the JAMMA Cable provided with
Properly eae oy unused the kit, unsolder your old JAMMA cable from the speaker,
Cable within the JAMM powersupply, control panel switches (which may already
anIe. be disconnected) and coin door. Remove the cable from the game. If you are not going to use the JAMMA Cable provided with the kit, check the JAMMA Cable Connector Chart to be sure your cable is compatible. Leave your power supply chassis as is.
- Connect the JAMMA Cable to J1 on the HIT THE ICE KIT video board. Using the JAMMA Cable Connector Chart for reference, solder the correct JAMMA Cable wires to the speaker, power supply, control panel switches and coin door.
- a) Fora(4) player conversion, wire the player 3/4 cable from players 3 & 4 control panel joysticks & buttons to connectors 3P & 4P on the CPU Board. (see drawing below)
- Fora(2)playerconversion, ignore above (a) andprocede.
- Place the FBI Warnng Label on the inside of the cabinet next to the PC boards. Be sure the label is completely visible.
HIT THE ICE CPU BOARD
Make sure the red bundle of wires goes to the Plager 3 connector,
and tha blue bundle cOnnECTOR
of wires goes to the plager 4 connector.
Installing the PC Boards and Wiring into a NON- JAMMA Game Cabinet
}. Disconnect and remove the existing video board in the JAMMA Game Cabinet.
- Mount the HIT THE ICE KIT video board inside the JAMMA Game Cabinet where the old video board was located
- Leaving several inches of wire, Cut the wires at the coin door, control panel switches (which may already be dis connected) speaker and power supply.
- Connect the JAMMA Cable to J1 on the HIT THE ICE KIT video board. Follow the JAMMA Cable Connector Chart and spiice the wires of the JAMMA Cable to the existing wires forthe coin door, power supply, speaker and Control panel. Be sure all of the spliced wires are well insulated with black electrical tape.
- a) Fora (4) player conversion, wire the player 3/4 cable from players 3 & 4 control panel joysticks & buttons to connectors 3P & 4P on the CPU Board. (see drawing below)
- Fora(2) player conversion, ignore above (a) and procede.
- Place the FBI Warnng Label on the inside of the cabinet next to the PC boards. Be sure the label is completely visible.
HIT THE ICE CPU BOARD
Make sure the red bundle of wires goes to the player 3 connector, JamMMA Be sure alll spliced wires are well insulated with black electrical tape.
Properly insulate any unused wires within the JAMMA Cable.
and the blue bundle CONNECTOR of wires goes to the plagar 4 connector.
Game Features
Starting Up
Switch on power tothe game. A "rug"pattern appears on the HIT THE ICE KIT is a two or four crt screen. The game then procedes to go through a self- player game. check. The game then moves to the attract mode. Afterthe proper coinage has been inserted, the game exits the attract mode and enters the play mode.
Player Controls
& Each Start button allows (1 to 4) players to begin play or continue play. When an error is detected during
- 1 Pass/Save Button per player. Start-up Tests, game start-up does not progress, and an error £§ 1 Shoot/Check Button per player. Message appears on the screen. 1 Joystick per player. Find below the suggested control panel layouts for a two player kit & a four player kit.
2 PLAYER HIT THE iCE CONTROL PANEL DIAGRAM
One Player Two Player Start Button Start Button
Player 1
Four Player ‘Start Button
Game Operation
HIT THE ICE is a one to four player video game with a color monitor. From the player's perspective, the game has two modes of operation: Ready-to-Play andPlay. Forthe owner/ operator, the game has a service option through the Dip Switch settings (ocated on Main Board, accessed through the pull-out shelf).
Control Switches
The COIN DOOR SLAM TILT SWITCH detects any forceful vibrations against the Coin Door. This eliminates pounding for free games.
[The VOLUME CONTROL allows increasing or decreasing the volume level of the game music and speech. For greater profits, set your game's volume level at its maximum (located on the Main Board, accessed through the pul-out shelf).
TheTEST/DIAGNOSTICS SWITCH is not used on this game.
#1 The SERVICE CREDIT SWITCH is a special feature switch that allots credit without affecting the game's bookkeeping total.
General HIT THE ICE Information
“Hit The Ice” is a 1 to 4 player video game based on the game of Ice Hockey. It takes place on the Official “VHL’ (Video Hockey League) ice rink pitting the Reds (left side) against the Blues (right side). Each team is made up of 3 players - 2 forwards and a goaltender. The object of the game is to shoot the puck into the other team's goal. What comes to mind when you think of “Ice Hockey”? Okay. Now forget all the stuff about confusing rules, obscure penalties and stoppage of play...and what are you left with? “Hit The Ice” Delivers!
Fights, Trips, Body Slams, Shattering Glass, Blazing Shots, Head over heels bone crunching hits, Hacking, Slashing, Spearing, Elbowing all out knock down, punching, crunching action. You don’t need to know how to skate to enjoy “Hit The Ice”- the ultimate red blooded sport, Fast paced end to end action, heart stopping incredible saves, booming slapshots, impossible in the air 360 degree cartwheel supershots (with some good natured humor thrown in).
“Hit The Ice” is designed for those totally unfamiliar with the traditional game of Ice hockey as well as for true fanatics of the sport. Don’t think we forgot the true hockey fan either “Hit The Ice” provides crisp passing, strategic play and players who skate with finesse and speed. And if that isn’t enough - we offer a power drink to each player between periods which turns you all star into an all out maniac on ice with a shot froma cannon! Power Drink-- during the locker room scene, players are offered the purchase (1 credit) of a power drink. As it says on the screen “Skate Faster, Shoot Harder, It really, Really works! A player inserts 1 credit and hits his start button to buy the drink. At the start of the next period you'll see your player undergo a wild cartoon like transformation that always gets a chuckle. And turns your player into a maniac. For the next 1:00. (Power drinks may be purchased only in the locker room.)
To speed up or skip pre game time out & locker room scenes, hold down ANY SHOOT button to make time run out on clock!
1 to 4 Player Competition
1 player game - player competes against the computer (he controls his character, his goalie, and partially his computer controlled teammate).
Two player games - players can team up against the computer or go head to head.
Players can also team up for a 3 or 4 player game.
Continuous Buy-in feature allows players to join in the game at any time.
Game Length
The game is divided into 3 five minute periods. Players return to the locker room between each period (and at a 2:00 minute warning during the 3rd period) to get playing tips and are each offered a “Power Drink” (purchased with one credit).
General HIT THE ICE Information Con’t.
Player Selection
Before play begins in the 1st period, players are asked to choose their goalies and the rest of their characters from a group of twelve. If they are not playing with another person on their team, the computer selects the “Hit The Ice” teammate for them.
As you move your joystick over the different characters you will seed them displayed full figure at the bottom of the screen showing their unique hitting style.
Each “Hit The Ice” character has his own unique style of a “Hit”.
Players begin the game with a faceoff at center ice. The player you chose has his face and name displayed at the top of the screen as the game progresses and he gets more and more beat up, you'll see it reflected in his face at the top of the screen - each major hit he takes - a new lump appears.
Fighting
With action this intense, fights are bound to happen - players who relentlessly slam, spear, and trip each other soon drop their sticks and gloves and go at it. Two fisted fun doesn’t stop the play (as there are no Penalties) so play continues with the winner skating off with the puck, and the loser on the ice shaking off the cobwebs. The best time to start a fight (and when they most often occur) is after a goal is scored - drop the gloves and work out your frustrations on you opponent's face! Loss of a fight results in loss of skating speed (and sometimes the ability to stand without falling down) for the next 10 seconds of play - so there is a clear advantage to winning fights! Lose 3 fights in a row and your player is carried off the ice to be replaced by a new player!
Player Controls (Skater)
To make a WRIST SHOT: Hit SHOOT Button & Hit JOYSTICK simultaneously. Tomake a SLAP SHOT: Hold down SHOOT Button & Release, Hit JOYSTICK simultaneously. To “FAKE” A SHOT: Hit SHOOT Button ONLY. To PASS: Hit PASS Button. To REQUEST A PASS: Hit PASS Button. To HIT: Hit CHECK Button.
Player Controis (Goalie)
To MAKE A SAVE: Hit SAVE Button. To “FREEZE” PUCK: Catch Puck/Wait for Whistle. To PUNCH: Hit CHECK Button. To PASS: Hit PASS Button. To PUNCH: Hit CHECK Button. REMEMBER: JOYSTICK CONTROLS GOALIE & SKATER
HIT THE ICE DIP SWITCH TABLE
Troubleshooting
Problem
NO PICTURE OR DISTORTED PICTURE.
TURN GAME ON & NOTHING HAPPENS
NO SOUND
NO GENERAL ILLUMINATION
MOVE JOYSTICK, BUT PLAYER DOES NOT MOVE OR FIRE
PRESS START BUTTON AND NOTHING HAPPENS
NO CREDIT GIVEN WHEN COINS ARE INSERTED
TOO MANY CREDITS FOR NUMBER OF COINS INSERTED
GAME WONT GO INTO THE TEST MODE. Possible Solution
Check for faulty video board or monitor. Check for disconnected video signal cable, or video extension cable.
Check line fuse. Check for +5V de at pins C, D, 3, and 4 of the JAMMA Connector.
Check the speaker and speaker connection to pins Land 10 on JAMMA Connector. Check volume control setting. Check for +12V de at pins F and 6 on the JAMMA Connector.
Check the 1A.,S-B fuse on the floor below the coin box.
Check for open wires between Joystick and CPU Board. Check for contamination on joystick switch contacts and CPU Board pins. Check for proper ground.
Check for open wires between button and CPU Board. Check for contamination on CPU Board pins or bution switch blade contacts. Check for proper ground.
Check DIP switch Coin setting. Check for contamination on coin switch contacts. Check for an open wire between Coin Switch 1 and pin 16 on JAMMA Connector or Coin Switch 2 and pin T of JAMMA Connector.
Check Game Pricing setting. Check for a short between pins T & 16 on JAMMA Connector.
Try to activate Dip Switch again (found on Main Board, access through pull-out mount Ing shelf).
1-14
HIT THE ICE KIT
SECTION TWO
Diagrams & Schematics
MPU 68000P-12 ° ) tye
oLeseDRE ID Be <D x L} a Be
c? Gesscatmacccccn «= ATT «| eas RRC RRC ham CDEDOD,., Dry yen 9606038 Pred me RRC RRC 3Ph
CP [bocaeGsbanacocooacG) ae, TF PitePaas
wD St(kqr008 11a] RAMI frm anf Tare conraeaton 1 $3256-100 $3256-100| MAIN PCD 43 gD ‘D RAMT RAMI
- 43256-1900 43256~-100 ery ee aL $3256-100 43256-100 any) cD is RAMI Rant 1LS3256~100 sP43256~100 GJ samMA @@ 6 seeqssess9se QQQLXAQPLOPPMLPOPLPPPPPPPPPPPPPPPPPPPOPPR, @GOga9888888988088
Oo GO ab wm wm
ee) "by Opin ef ao ec pects
EE NOTE 6
QS no mount REVISIONS
Soo MARK
RRC CATHODE MARK Xo ELEC.BLOCK TANT,. DIP & CAP,FILM © CAP,.CERAMIC
NOTE 2 BEADS FILTER
sew (DP cy PRINTED FACE -NOTE3.. TRANSISTOR.
OTE4 POWER AM
vex jp Vana cut NOTES. JUMPER
CPU ASSEMBLY 2-1
°
>
| 7 | i | 6 | LL | _ | _ | 3 | tl | 2 | : | t |
PT LOS (2-70, 4-4, 7-70, 12-66 17-7 Lo REVISIO + | —— JOS (2-70, 2-66, -- 1. F-3e - j_cra | oescarprion | oate| appaorved| | [7 /as (2-70, 12-68) (14-70. 32-70) 4 CPUA (2-60. 3-78.5-54, 7-70, 9-7C, 11-40) A, i
| 68000-12 | AY 271001/ 4000 | ‘by 274001/1000 | 5563 | ||
| S2MHZ | 15 Ieik aos {23 | 12 Jao oo[ 13 | 12 Ino oof+3 9 | AO 01 | |
| (2-10) | 20 | ao2[30 | 14 Igy orjt4 | $1 lay o1 . $ | As 02 |
| + i8areseT 203 [33 | 10 Jaa 02,45 | 10 \,2 02 | A203 | ||
| ao4|32 | Stag 03,42 | 9 a3 o3,47 3 | A3 4 | ||
| A05 | 8 | < | Ad a5 | ||
| {| _ | 7 | 5 | |||
| 8 KS | A06 | 2 | : | AS 06 | |
| 7 Woos | A07 | 8 | AG 07 |
- }} 8 tos A0B AT aa /oTackK_t) 10 d07kTK 409 Ae onic
| (2-40) | A9 Nae ALO | Ag 4g |
vp, —— 1-2 Wien Ati aro vee M1
| (2-50) | tah | ae | 26 |
| eA | Ai3 | A12 3g |
{12 tecaex Ata OE GNno
| Aides | AMS | WE 44 |
—AlgatT ais cs e+ 22 BERR Ad7 toons
| 25 | tie | TCbe |
Teto 8649 (2-50) / TPL 24qPtt = 420
| (2-50) /TPL2 | 23dTPt2 kas | /#ORK (2=5C) | |
| - | A22 | 7LCS (2-20) | |
| (2-70) FCO- | 28 Ico | A23 | 7 RO (2-2C) |
| (2-70) Fc | 27 ecy | 000 |
(2-70) Fc2 28 koa D041
oo2
| bi | 271001/1000 | 5563 |
| tee | 12 tao 00 e u | Ao 01 |
| 006 | 14 Jay oip44 9 | As 02 |
| Do? | $0 Ina oat ts | A2 03 |
S143 03,12 Ag 04 vee 008 Ho 14,49 999 GND 06 18,53 040 06 or oa
013 N.C
A 10 yee ous ALL R/ W 26 1c27 A12 35
6NO
————4 100ns Tc40 g g JWORK (2-5C) L/W > «
| Syes | - | /W08 (2-20) |
(4- 4a) 70 (2-20) (8-10) paces (14-50. 11-70, 12-78) 86SEt . - a - Lso7 CPUO(2-5c, 3-68.7-70. 9-70)
| / ORES | 9 | 7 |
(3-6C) Ic24 Lso7 it 10
tc24
(2-10. 2-20, 3-6C) RDWE (4-44, 7-6C, 8-10. 12-68)
| 7 | « | 6 |
ow
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
CPU 2-5 VCU_CL (11-20) Fa
CPUA (1-29) (2-BA)V/ VALE (1-70)/ Los (1-70)/ uvos—__ 82 yuos
(1-64) AOWE (2-sC)/ vcu -7A)/RESET- (2-70VVvCu-oTA—__2?// oT ack (2-50) INT4 INTL (2-58, 3-6C, 12-7ALNTS 87 inte (7-50, 42-7ABLANK 68 lcouPBLANK (7-48) SYNC 58k ompsync 79leLocKIN 144Pin FLAT It29 TCO*BOVE U FO26 Fo2s5 FO24 F023 FO22 Foes Fo20 Fos Foie FOIT7 FOS FO15 FO%4 FO13 FO12 FOu4 Fo10 FOS Foe FO? Fo6 FOS FO4 FOS Foe Fo. FOO
CH (6-30) (7-30. (7-6¢, 12-58. 7-60) v >+—_
12-7A) IC314 ol oste7
- 6MHZ~ 164M in
0 LE L 43, 5MH2Z2 (7-30, 7-50) CHALE (6-4C) (5-70) FO (5-5C)
REVISIONS oescartprron | oare japprosco
FA (4-70)
43256
| 9 | to [ro oo Ltt 0 | 16 |
| 4 | Sky oy [42 | 17 |
| G | 8 th2 o2 [132 | 18 |
| 3 | 2 In3 03 [45 3 | 19 |
| 4 | 6 lag o4 L156 4 | 20 |
SoS ks ogg [47 5 21
| B | “tke 6 | 18 6 | s4 |
——3_Ia7 o7 [13 7 23 O 25 |g 9 24 Ihg 49 24 Ih 4 23,44 vec 42 2 Iny2 28 13 26 443 GNO 14 1 olaga 14 (4-70) / FHEO 27 RE “ 72 Fone Se Pe 15 $00nS 4 1c7
FDO (4-60)
| 43256 | 43256 | 43256 | |||
| 9 | 10 fo oo Lt 0 | 0 | 10 fro oo Ltd 8 | 0 | 10 [hg oo L1t 16 |
| Stay oy (42 | 1 | Tht 001 (229 | 1 | Soa: oy (4247 | |
| a | 8 lho o2 (43 2 | 2 | 8 lao 02 [23 10 | 2 | Carey o2 (13 18 |
| E) | 7 W393 [953 | 3 | 7 oMk3) 03 [4581 | 3 | 7 |a3 3 [4819 |
| 4 | 8 hq o4 [48 4 | 4 | 6 lau oa (18 12 | 4 | 5 lhe og [28 20 |
| 5 | 5s os [475 | 5 | 5 las os [47213 | 5 | Sas os [12 24 |
| § | 4odas og (18 6 | 6 | 4 lh os [18 14 | 6 | 4 lag og [13 22 |
| Z | 3_Ia7 o7 (19 7 | 7 | Ema he) o7 19 15 | 7 | 2 a7 o7 [13 23 |
| é | {| 25 hg | 8 | 25 laa | 13 | 25 ip |
| E | 24 Ihg | 9 | 24 |ag | Ts | 24 |g |
| 40 | 21 thi | 10 | 21 lato | 10 | 21 thio |
| i | 23 |,44 vec | i | 23 Iayy VOC | it | 23a dary 3e% |
| i | 2 Inia 28 | 12 | 2_lay2 28 | 12 | Zhaie 26 |
| 13 | 26 [443 GNO | 13 | 26 |, 43 GNO | 13 | 26 4,3 one |
| 14 | — $ootaga 14 | 14 | 1 odaya 14 | 14 | t olga 34 |
| LL 27 We | 27 hE | 27 ke | |||
| ) | 22 40 | 22 toe | 22 be | ||
| FHEN | {cs | 20 eS | 20 Ke | ||
| (4-70) | 10ons | 5 1000s | 5 100nS) | ||
| Ice | IC6 | 1c4 |
+ + + +
| 7 | si | 3 | - |
CPU 2-6
HEVISTONS ural oescaterrom |oare |approveo
CH (4-28)
234000
A0 At Az Oo
x=
oO
CHALE (4-20)
CPU 2-7
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
MIX
PCM (8-38)
(9-28) +12V
o = 3 |?
14, 7uFC
r c54
E220uFC c56 4 | 5}
E1qgouFC c49
raeeale a] G-10) SP(+) MB3735 7 ; . 1c46 8 i LJ G-t SP [-) WITH HEAT SINK |
7 w]e 1/2W x2 o | 104F SWNG 8 od = |, o E100uFC Loar aw i
CPU 2-11
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
Coin Switch and Meter Wiring
Option 1
+5V
Meter
JAMNA Pin 16
JAMMA Pin 8
Option 2
Coin Sw 1 >
JAMMA Pin 16
Coin Sw2
JAMMA Pin T JAMMA Pin8 Gnd
JAMMA PINJ
Wrong Way !
Coin Sw 1 - JAMMA Pin T
JAMMA Pin 16
Do NOT Connect the coin switches this way. This Circuit is INCORRECT and will cause twice as many credits per coin.
2-15
HIT THE ICE KIT
Jamma Chart
Function
GROUND A
GROUND hepato
a
#o13NNOO 3903 ONIHIM LANIGVS LDi 30! SHL LIH
2-17
& __. ANS Slo FHOLES
ls
nei = Ww
aw z DIA. TA RU F+/OLLES
—a| Nig h—
Ss 10 -F/P/ TE/IPLATE CONTROLS PLAYER */ USED ON 30203 K/7T
Ve DIA. THRE
F HOLES
3 DIA.THRY / (84 POLES
SG 3F = -/ 3 IN
& = 3 ——_+
SO-F/P-1 Le
TEMPLATE CONTROLS
PLAYER 2 USED ON 30203 K/7 2-19 = 1 = AK ——
a \y Vjz DIA. THRE FHOLES
Z Le at ae
$ ey
yao ‘3 wi —t I * # an THIRY 2 HOLES pe ae 7E/IPLATE CONTROLS
PLAYER FS
2-20 USED ON 30203 KIT
12 DIA. THRE F/IOLELS
: T
+
oy ‘8 |} Cg
——/ ae if Loam} — 3 2 vA “> a SF Ve “eA | /9 | 14
—_ 3 BZ DIA. TARY /O-WP -3Z FLPIOLES TE/IPLATE CONTROLS 2-21
PLAYER *F
USED ON 30203 KIT
NOTES:
NOTES:
WARNINGS & NOTICES
- For safety and reliability, substitute parts and modifications are not recommended.
- Substitute parts or modifications may void FCC type acceptance.
- This game is protected by federal copyright, trademark and patent laws. Unauthorized modifications may be illegal under Federal law. This also applies to WILLIAMS logos, designs, publications and assemblies. Moreover, facsimiles of WILLIAMS equipment (or any feature thereof) may be illegal under federal law, regardless of whether or not such facsimiles are manufactured with WILLIAMS components.
Notice When Williams Electronics ships a game, it is in compliance with FCC regulations. Your sticker is proof. If the sticker is missing or damaged, legal repercussions to the owner or distributor of the game may result. If your game kit does not contain an FCC sticker, call Williams Electronics immediately.
Notice No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may be transmitted, or otherwise copied for public or private use, without permission from the publisher.
Entire contents of this manual copyright © 1990 WILLIAMS ELECTRONICS GAMES, INC. All Rights Reserved.
Programmed By TAITO CORPORATION.
WILLIAMS ELECTRONICS GAMES, INC. 3401 N. CALIFORNIA AVE. CHICAGO, IL 60618
FOR SERVICE:
CALL YOUR AUTHORIZED WILLIAMS DISTRIBUTOR.