Time Pilot 84 Kit Instruction Manual
Time Pilot '84 (set 1) (Konami, 1984) · Instruction Manual · 11 pages · 16 sections · original scan
nm CONVERSTONAAIT INSTRUCTION MANUAL
bbe ~~ ~ ~~ TIME PILOT'84™ and Konamls are the trademarks of Konami Industry Co., Ltd C Konami 1984 All rights reserved
20655 S. WESTERN AVE., SUITE 116, TORRANCE CALIFORNIA 90501 Konami, Inc. TEL. :(213)533-8644 8648 TELEX:4720119 KONAMER FAX.:(213)533-6040
TIME PILOT’84 CONVERSION KIT: INSTRUCTION MANUAL
CONTENTS
© CONTENTS OF CONVERSION PACK-+:::s:ereirriee 1 eo) TO THE TECHNICIAN errr rrr eter rere re ee etree eee eee eee 2 «INTRODUCTION
- BEFORE CONVERTING
- QUESTIONS AND ANSWERS re) IMPORTANT nec e cece nee e nee eee e een eeneeeseeeeseseeaceee O WARNING este errr od © TROUBLESHOOTING: +:+:+:s::ereeteeeeeeetititetettertes 5 *CONTROL *MONITOR *POWER SUPPLY © DIP SWITCH SETTING «ecceceeceecceec tec eee eee eee eee neneeen eens 6 © GENERAL WIRING DIAGRAM ------:-0--eseseseeeeereeees 7 © DIAGNOSTIC PROG.(PCB) titties 8 SELF TEST
- MANUAL TEST © HELPFUL SUGGESTIONS -1t ites 9
' CONTENTS OF CONVERSION PACK 1-Main Printed Circuit Board, P C. Board Cage | 1- Wiring Harness : | 1- Marquee Overlay(Header) 1 set- Side Panel Graphics(Left and Right) 1-Control Panel Overlay 1 set - Control Button Decals (1 player, 2 player, lever, play instructions, copyright seal) 1- Joystick 2- Push Buttons 1- Technical Instruction Manual 1- Registration Card
~
TIME PILOT’84: TO THE TECHNICIAN
INTRODUCTION
This instruction manual has been specifically designed for your use. It will provide you with enough information to convert your old game as simply as possible. These are general points necessary for operating “TIME PILOT 84" safely and securely.
BEFORE CONVERTING
- Be sure that you have all the necessary parts.
- The wiring diagram for “TIME PILOT'’84” is exactly the same as those for some of Konami games such as “GYRUSS", “TIME PILOT”, “ROC'N ROPE” and “SUPER COBRA”. So you only need to insert the new P. C. Board in case your game is one of them. However, close attention should be paid to the wiring diagram if you are not converting a Konami game
QUESTIONS AND ANSWERS
. What machines can be converted? . Any game with color raster monitor can be converted with this kit.
. Will it be necessary to change the power supply? . If present power supply cannot handle the following current parameters, it will be necessary. +5V 7.0A MAIN BOARD +12V 2.0A SOUND BOARD PO ro
Q. How much wiring is involved? A. Relatively very little. By using the old wiring, you can save time by soldering the new connecting wires to the old ones. These old wires show exactly where to connect the new wires (See the wiring diagram). Q. Will it be necessary to replace the present joystick and buttons? A. Yes. This kit includes the most suitable joystick and buttons for this game.
‘ ;
:
TIME PILOT’84: IMPORTANT
There is one very important thing for you to know. That is, whether your monitor's sync. is positive or negative.
SYNC. OF THIS P.C. BOARD APPEARS IN THE NEGATIVE PULSE IN THE TERMINAL
(1 )If your TV monitor requires tuning, adjustment must be made. Adjustment means altering composite sync. by using the IC chips known as 7404 or 74LS04. For your information, in case of this P. C. Board, the signal on this pin is a method which is a combination of HSYNC and VSYNC. , re +5V
7404 or 74LS04
from P.C. Board
- Ih
Composite Sync. OUTPUT TO MONITOR =, > (+5V and GND should be taken out of the P. C. Board.)
(2)Separate Sync, modification for “TIME PILOT'’84” . If your monitor has “Separate Sync” input, for example “Electro home made” and
- “Wells-Gardner made”. 1Step | {Negative Sync input
-H] -V| Gnd Fo \ ' ' i Blue_13 (Blue/White)? Green P (Green/White) | t
Hl
\ ‘Sync _14 (Black/White) Red _R (Red/White)
Wiring Harness | Monitor Board
Still the picture is not stable. 2 Step 2 Prepare Hook-up wire. For example “Electro home made”
B A Negative Sync input
-H| -v | Gng| Blue_13 (Blue/White) Green _P (Green/White) Syne _14 (Black/White) Red_R (Red/White) H| Vv [Gnd] B|G]R
Wiring Harness Monitor Board
[wire Logic Board PWBIB) e005]! 3000 1578
JST CONNECTOR RTB-1.5-4F
age
' TIME PILOT’84: WARNING
OPERATOR INFORMATION
WARNING
F.C. C. REGULATION COMPLIANCE
The P. C. Board cage supplied with this conversion kit must be used and grounded at the time of installation.
This is required to avoid radio frequency radiation and to comply with the s limits for a class “A” computing device pursuant to Subpart “J” of Part 15 of i F.C. C. Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment.
The operation of this equipment in a residential area, is likely to cause interference - in which case the user will be required to take whatever measures are necessary to correct the interference at his own expense.
TIME PILOT’84: TROUBLESHOOTING
Before returning the P.C. Board for repair, the following should be checked (a video game is composed of these three main blocks and a P. C. Board).
CONTROL
The joystick does not work in a specific direction. x The shooting button does not work. ®@ Check the condition of the joystick and button. ®@ Check the contact of the wiring harness.
MONITOR
W@iThe screen is dead. WiThe picture does not stand still. The picture is either too big or too small The picture is contorted Wcolors are wrong. @ Check if something is wrong with the monitor. @Check conditioning of the monitor. @Check the contact of the wiring harness.
POWER SUPPLY
@iThe power supply is dead. od HENo sound(+12V) Wit intermittently moves wrong. Mit sometimes becomes reset. @Check+5V and +12V @ Check stability of voltage. @ Check the contact of wiring harness.
if there should be a necessity to alter it, it should be done with enough ___| consideration.
{ ‘COIN 1 FREE PLAY | | COIN 2 INVALIDITY LL — - - 7 (ATTENTION) Free play means the situation, you can play without putting any COINS in
@DIP Sw 2 SET
- SWITCH FOR CHANGE OF TABLE OR UP RIGHT swl 3 | WE OSC~*d
| | | | | OFF | TABLE: | W/O for 1 or 2 player | i |
| 1 | ONT | 19 VO for only 1 player _| |
BONUS POINTS 1.0000 POINTS AND AFTER EVERY 50000 POINTS: ON | 20000 POINTS AND AFTER EVERY 60000 POINTS
- SOUND IN ATTRACTIVE MODE |SW) 8 SOUND IN ATTRACTIVE MODE
| i | OFF | | SOUND _ OFF | _ | |
| |_2[ | ON | | SOUND | ON | _! |
vR
LOUD
VR is for adjustment of sound volume. The volume is decreased by turning. VR counter-clockwise.
30000 POINTS AND AFTER EVERY 7 0000 POINTS ON [40000 POINTS AND AFTER EVERY 80000 POINTS
- DIFFICULTY OF THE GAME [DIFFICULTY _ | 1 (EASY) | 2 1 2. 4 (DIFFICULT) ON | DIP Sw2- 12345 67 3
ON -
ove sw
123 45 6°7 8
6 eee
[NOTE] ’ In the case of “UP-RIGHT TYPE”.
No need to use the following
terminals on a connector.
C:2P SHOOT 1
D:2P LEFT
3:2P SHOOT 2
4:2P RIGHT
6:2P UP 9:2P DOWN Follow this instruction for(+12V) the power supply.
capacity. REQUIRED SPEAKER POWER CAPACITY
Q 12V 1A 12V 2A 12V 2A NOT APPLICABLE SPEAKER1 ‘82 ao@ 6W SPEAKER2 (mini)
ew (mini) WIRE COLOR CODE ILINE COLOR//BASE COLOR ORANGE A IS SOLDER SIDE BIS PARTS SIDE
BA
GREEN Vy +tav A
7 GREEN a SPEAKER OUT
7 BROWN B]SPEAKER OUT
BROWN oo 2P SHOOT 2
ZORANGE —{C]2P SHOOT 1
7 BROWN, BI 2P RIGHT
7 BROWN [D)2P LEFT
ZYELLOW 5] 2P START
Z BROWN YELLOW E]iP START 6] 2P UP
57 7-sSERVICE WHITE FIP SHOOT 2
ZYELLOW
s—1-S1P SHOOT 1 1 SP LEFT YELLOW, heise H}1P SHOOT 1
<1 “iP RIGHT 7 YELLOW 1P LEFT
Z ORANGE J}iP RIGHT
Z YELLOW, 9] 2P DOWN
WHITE {K}iP UP
12V COIN COUNTER ZWHITE fio] COIN 2
COLOR MONITOR [RED }$—7—_, IgreEN 1 + irae Z WHITE LJCOIN 1
YELLOW 1] COIN COUNTER 1
i] Foor | 12V COIN COUNTER WHITE —{M}iP DOWN
WHITE ZWHITE 12] COIN COUNTER 2 fis[ BLUE
ee 10D1 Z WHITE, WHITE
ISYNC IGND + PJGREEN
AC INPUT ISOLATE POWER SUPPLY
TRANSFORMER FOR
NOISE FILTER EARTH o oe + WIRING HARNESS CONNECTOR KEL 1168-036-009 =a = m U i fo} oe) ES * GENERAL WIRING DIAGRAM =
| TIME PILOT’84: DIAGNOSTIC PROG. (=ce) Ls
SELF TEST
This P.C.Board has a function to check if there is anything wrong with the cabinet or P.C.Board itself When the power is switched ON the board will always check the basic block and if normal, indicate OK on the monitor and then will start the game. If not normal, it will indicate —B.VD_ and the picture will stop.
MANUAL TEST
- How to Start Switch on the power while pressing both 1P and 2P buttons until the cross ‘hatch appears on the screen Switch off the power once, before starting the game
- How to Select the Test Item oTest items will change in the following order as you push 1P button each time. When Item 6 is over, Item 1 will come back e oEach item will last until you push 1P button.
- Test Items
Item Details
1 Conditioning of __ Cross hatch will appear all over the Picture Contortion screen. 2 Color Conditioning — 16 blocks will show the colors. Adjust the monitor 3 Control Check — Names of all the switches (lever, COIN SW, etc.) will be on the screen. As you turn on each of them, “O" on its right will turn to “1”. 4 Coin Counter Check — To check the coin counter, counts up Coin Counter 1 and then Coin Counter 2 eight times each. Then move on to Item 5. DIP SW SET will be displayed on the screen. DIP SW condition will be read into computer only when the power is switched ON. 5 DIP SW SET
There will be sounds for testing purpose There will be automatically 8 seconds’ interval between one sound and next. The cycle of sounds will repeat. 6 Sound Check
a
TIME PILOT’84: HELPFUL SUGGESTIONS
THE FOLLOWING PROCEDURE IS RECOMMENDED BY THE GRAPHICS MANUFACTURER IN APPLYING THE SIDE PANEL DECALS AND MARQUEE OVERLAY
ONLY.
- REMOVE PROTECTIVE BACKING FROM DECALS.
- LAY OUT DECALS, ADHESIVE SIDE UR AND SPRAY EVENLY WITH A FOAMING AEROSOL SUCH AS "“WINDEX" . .
- USING THE SAME SPRAY,SPRAY THE AREA OF THE CABINET AND MARQUEE WHERE DECALS ARE TO BE APPLIED.
- POSITION THE DECAL INTO PLACE
5, USING A SOFT SQUEEGEE OR PIECE OF CARDBOARD, BEGINNING AT THE CENTER OF THE DECAL, SLOWLY AND EVENLY PRESS OUT THE EXCESS FOAM UNTIL YOU ACHIEVE A SMOOTH FINISH:
- ALLOW TO SET APPROXIMATELY 2 TO 3 HOURS,
THIS PROCEDURE HAS BEEN FOUND TO BE THE MOST EFFECTIVE WAY OF ENSURING THE PROPER POSITIONING OF THE DECALS AS IT CREATES MANEUVERABILITY OF THE DECAL AND IS AN ADDED PROTECTION AGAINST THE DECAL COMING LCOSE OR CREASING DURING APPLICATION
IT 1S RECOMMENDED THAT ALL DECALS AND STICKERS BE ALLOWED TO SET FOR 24 HOURS AFTER APPLICATION FOR MAXIMUM ADHERENCE,
© Konam