Robotron Instruction Manual (16P-3005-101) May 82
Robotron: 2084 (Solid Blue label) (Williams / Vid Kidz, 1982) · Instruction Manual · 11 pages · 16 sections · original scan
16P-3005-101 Hiltiams @ io
FOBOro:
INSTRUCTION MANUAL
FOR
UPRIGHT AND COMPACT GAMES
Including procedures for...
¢ Operation
e Auditing
e Adjustment
¢ Diagnostics
or service ° Noe NEW TOLL-FREE Dj TELEPHONE NUMBERS: ELECTRONICS, INC. 800-621-1253 > N. Califo In Illinois call: a i 60618 : Cable Address: WILCOIN, CHICAGO 800-572-1324 (a12) 267-2240
ROM SUMMARY
Current Robotron Games use blue-label ROMs. Earlier games have either yellow or red-label ROMs, which are interchangeable and may be mixed in the same game. DO NOT attempt to mix blue-label ROMs with red or yellow-label ROMs.
| ROM | PART NO. | DESCRIPTION |
| ROBOTRON 1B | A-5343-09898 | PROM, 4Kx8, RED or YELLOW LABEL |
A-5343-09945 PROM, 4Kx8, BLUE LABEL
| ROBOTRON 2B | A-5343-09899 | PROM, 4Kx8, RED or YELLOW LABEL |
A-5343-09946 PROM, 4Kx8, BLUE LABEL
| ROBOTRON 3B | A-5343-09900 | PROM, 4Kx8, RED or YELLOW LABEL |
A-5343-09947 PROM, 4Kx8, BLUE LABEL
| ROBOTRON 4B | A-5343-09901 | PROM, 4Kx8, RED or YELLOW LABEL |
A-5343-09948 PROM, 4Kx8, BLUE LABEL
| ROBOTRON 5B | A-5343-09902 | PROM, 4Kx8, RED or YELLOW LABEL |
A-5343-09949 PROM, 4Kx8, BLUE LABEL
| ROBOTRON 6B | A-5343-09903 | PROM, 4Kx8, RED or YELLOW LABEL |
A-5343-09950 PROM, 4Kx8, BLUE LABEL
| ROBOTRON 7B | A-5343-09904 | PROM, 4Kx8, RED or YELLOW LABEL |
A-5343-09951 PROM, 4Kx8, BLUE LABEL
| ROBOTRON 8B | A-5343-09905 | PROM, 4Kx8, RED or YELLOW LABEL |
A-5343-09952 PROM, 4Kx8, BLUE LABEL
| ROBOTRON 9B | A-5343-09906 | PROM, 4Kx8, RED or YELLOW LABEL |
A-5343-09953 PROM, 4Kx8, BLUE LABEL
| ROBOTRON 10B | A-5343-09907 | PROM, 4Kx8, RED or YELLOW LABEL |
A-5343-09954 PROM, 4Kx8, BLUE LABEL
| ROBOTRON 11B | A-5343-09908 | PROM, 4Kx8, RED or YELLOW LABEL |
A-5343-09955 PROM, 4Kx8, BLUE LABEL
| ROBOTRON 12B | A-5343-09909 | PROM, 4Kx8, RED or YELLOW LABEL |
A-5343-09956 PROM, 4Kx8, BLUE LABEL
| Decoder ROM 4 | A-5342-09694. | PROM, 512x8 |
(Horizontal)
| Decoder ROM 6 | A-5342-09821 | PROM, 512x8 |
(Vertical)
| Video Sound ROM 3 | A-5343-09910 | ROM, 4Kx8 |
Special Chip 1 A-5410-09911 Special Chip
POWER TURN-ON
WHEN THE GAME IS FIRST TURNED ON it produces a sound. Simultaneously general illumination should come on and a moment later a scanning “rug pattern” indicating the RAM test should appear on the screen. Next the rug should become stationary as the ROM test is performed. In a correctly running game the rug pattern will be followed by the message "INITIAL CHECKS INDICATE: OPERATIONAL". If RAM or ROM failure messages come up on the screen instead, refer to Power-Up Tests in TROUBLESHOOTING PROCEDURES.
GAME OPERATION
GAME START - Insert coins; a random sound is produced and credits are displayed on the CRT. With one or more credits displayed, pressing 1-player start initiates a l-player, *3-turn game. With two or more displayed, pressing 2-player start initiates a 2-player, *3-turn game.
PLAYER CONTROLS
MOVE JOYSTICK (LEFT) maneuvers mutant clone (our hero) in any of eight directions: N-NE-E-SE-S-SW-W-NW.
FIRE JOYSTICK (RIGHT) fires anti-robot laser gun in same eight directions.
GAME PLAY
ROBOTS ARE THE ENEMY - The player (represented by the mutant clone) must deactivate six types of robots with a laser gun. However the robots' armada including tanks, electrodes and cruise missiles will be deployed against the mutant. Meanwhile defenseless normal clones must be protected by the mutant or they will be captured and reprogrammed by the robots. Arriving at 25,000* points (or any multiple of 25,000), the mutant is awarded a new opportunity to defend his clonekinsmen.
HIGH SCORE SIGNATURE
Select letters with the MOVE joystick. Push up to move forward through the alphabet; pull down to move backward. Then push the FIRE joystick up to lock in the letter.
BOOKKEEPING AND EVALUATION TOTALS
- In Game-Over Mode, open the cashbox and depress the cashbox advance switch. The advance switch located on the coin door can also be used. The CRT should indicate all bookkeeping and evaluation totals. If so, go to step 3. If the CRT display comes up in the ROM test, perform step 2.
AUTO-UP
HIGH MANUAL ADVANCE SCORE DOWN RESET
Figure 1. Coin Door Button Switches
- Continue to depress the cashbox advance switch, stepping the game through test programs for ROMs, RAMs, CMOS RAMs, color RAMs, sounds, switches, and then CRT test patterns, of which there are five. The fifth test pattern, color bars, directly precedes the CRT display of the bookkeeping and evaluation totals.
- The bookkeeping and evaluation totals appear on the displays as in Figure 1.
- Adjustable feature
CLEARING BOOKKEKPING TOTALS
Depress ADVANCE to display Game Adjustments. Operate MOVE joystick to position cursor on CLEAR BOOKKEEPING TOTALS. Push FIRE. Depress ADVANCE. RwNe
BOOKKEEPING TOTALS LEFT SLOT COINS 16 CENTER SLOT COINS 0 RIGHT SLOT COINS 426 PAID CREDITS 593
EXTRA MEN EARNED 221 PLAY TIME IN MINUTES 1200 MEN PLAYED 2000
CREDITS PLAYED 593
AVERAGE TIME PER CREDIT 2:01
AVERAGE TURNS PER CREDIT _ 3.37
Figure 1. Bookkeeping display
GAME ADJUSTMENTS
In the Game-Over Mode open the coin door with AUTO-UP, and depress the coin door ADVANCE switch twice to cause a CRT display as shown in Figure 2.
To select and then set functions to the desired values, use the MOVE (UP-DOWN) joystick to select the that is to be changed and then, making sure the coin door is open, use the FIRE (UP-DOWN) joystick to increase or reduce the value of the selected function.
The number of turns per game can be set anywhere from | to 20 (3 recommended). Difficulty is factory-programmed at 3 (liberal). It can be custom-programmed (0-10, with 10 conservative) as desired.
Game pricing is selected with standard settings or with custom settings as shown in Tables | & 2. Table 1 lists some common pricing schemes and directs the reader to the proper entry in Table 2, which shows what the CRT display should look like to accomplish the desired pricing. Note that free play can be elected by entering the code number 9 at the PRICING SELECTION function (see Tables 1 and 2).
For standard settings you need change only the PRICING SELECTION. For custom settings, first set PRICING SELECTION to zero and then set the remaining values according to Table 2.
GAME ADJUSTMENT
EXTRA MAN EVERY 25000 RECOMMENDED TURNS PER PLAYER RECOMMENDED
PRICING SELECTION 1/QUARTER 4/DOLLAR LEFT SLOT UNITS CENTER SLOT UNITS RIGHT SLOT UNITS UNITS REQUIRED FOR CREDIT UNITS REQUIRED FOR BONUS CREDIT MINIMUM UNITS FOR ANY CREDIT FANCY ATTRACT MODE DIFFICULTY OF PLAY LETTERS FOR HIGH SCORE NAME RESTORE FACTORY SETTINGS NO CLEAR BOOKKEEPING TOTALS NO HIGH SCORE TABLE RESET NO AUTO CYCLE NO SET ATTRACT MODE MESSAGE NO SET HIGH SCORE NAME NO USE -MOVE- LEVER TO SELECT ADJUSTMENT USE -FIRE- LEVER TO CHANGE THE VALUE
PRESS ADVANCE TO EXIT LIBERAL RECOMMENDED YE
Figure 2. Game Adjustment
Highest Score Signature
The number of letters allowed the highest scoring player for entering his name can be varied from 3 to 20 and is recommended as 3. If objectionable words are entered as the signature name, you can change the lettered entry leaving the highest score the same. See Setting Highest Score Name.
Restore Factory Settings Position the cursor on RESTORE FACTORY SETTINGS. Push FIRE. Depress ADVANCE. wn
Resetting High Score Table
Position the cursor on RESET HIGH SCORE TABLE. Push FIRE. Depress ADVANCE. wn
Setting Attract Mode Message
Position the cursor on SET ATTRACT MODE MESSAGE. Push FIRE. Depress ADVANCE. Enter up to two lines of your message following instructions on the screen Depress ADVANCE to terminate process. WURUNS
Setting High Score Name
Position the cursor on SET HIGHEST SCORE NAME. Push FIRE. Depress ADVANCE. Enter new signature; depress ADVANCE to terminate process.
Table 1. Pricing Schemes
TABLE 2
| COIN DOOR MECHANISM | CREDITS/MONEY | STANDARD SELECTION/ |
CUSTOM KEY Twin Quarter 1/25¢, 5/$1 Quarter, Dollar, Quarter 2/50¢, 5/$1 1/25¢, 4/$1 2/50¢, 4/$1 1/50¢, 3/$1, 4/$1.25 1/50¢, 3/$1, 7/$2 1/50¢, 3/$1, 6/$2 1/50¢ 1DM, 5DM 1/1DM, 6/5DM 20-Cent, 50-Cent 1/20¢, 3/50¢ 1 Franc, 5 Franc 1/2F, 3/5F ole Rr alt wlolrlofalalalalnfrolun-moaww> 25 Cent 1/25¢, 4/1G 1 Guilder 1/25¢, 5/IG 5 Franc 1/SF, 2/10F 10 Franc 1/10F 1 Franc, 2 Franc 2/1F 5/2F 100 Lire, 200 Lire 1/200 Lire Twin Coin 1/1 Coin 1/2 Coins 1/3 Coins, 2 5 Coins 1 Unit, 5 Unit 1/2, 3/5 1/1, 5/5 1/3, 2/5 FREE PLAY -
Table 2. Pricing Settings
| DISPLAY | STANDARD | SELECTION | CUSTOM KEY |
FUNCTIONS A/|B/C{|D|JE|F|G/H/|I]J
| Pricing Selection | 1 | 2/3 | }4)5)6)7/8)9})0/0)0)0;/0;/0}]0]0);0)0 | |||||||||||||||
| Left Slot Units | 1 | 6 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 3 | 12) | 6 | 1 | 2 | 1 | 2 |
| Center Slot Units | 4/0]}4)16}4]0]/0)0/4]4)4)] | 4/12/48} | 0)]0)])0;]0)0 | |||||||||||||||
| Right Slot Units | 1 | 1 | 1 | 6 | 1 | 4)2]2 | 1 | 1 | 1 | 1 | 3 | }12) | 15} | 4 | 2] | 5 | 10 | |||
| Units per Credit | 2 | 1 | 1 | 2/2 | 1 | 1 | 2 | 1 | 1 | 1 | 1 | 4) | 14] | 5 | 1 | 5 | 1 | 5 |
Units for Bonus Credit 4/0/0);0]0]0]/0);0/0]/4)4/]/0/15])/96;}0)4)0}]0)0 Minimum Units forCredit | 0 | 0 | 0 |0/0/0]0/0]0{0/]2]2{|0424;0}]0}]0/]0j0
TROUBLESHOOTING PROCEDURES Certain types of game malfunctions may inhibit the game's diagnostic or display faculties. Troubleshooting procedures of malfunctions as well as malfunctions that permit self-diagnosis are covered below. for most of these types Our troubleshooting algorithm begins with Power-Up and continues until Game Over Mode. performed with minimal test equipment or merely by observing the game itself. All procedures can be
POWER-UP TESTS NO GENERAL ILLUMINATION NO INITIAL VIDEO (RUG PATTERN) CHECKING POWER SUPPLY BOARD (I) Check fuse F2 on power supply board.
- Check for proper installation of jumpers W1, W2, W3 and/or resistor R27. (Some machines DO NOT have an R27. Refer to your drawing set.)
- Check 4P1/J 1, 4P3/J3, 6P2/J2 and 6P3/J3.
- If all the above don't turn up the problem check power supply board.
- Open back doors
- Press reset button on CPU Board.
- Try RAM and ROM tests (see below).
- If all the above don't turn up the problem, check power supply board.
- Swap power supply board with one from known-good game.
- If game plays, problem is on power supply board.
- If game doesn't play, check power transformer with voltmeter.
- If known-good power supply is unavailable for tests above, check +5V,—5V and + 12V outputs on power supply in game. Each MUST BE within 2% of rated output with less than 0.1% AC hum. MORE POWER-UP TESTS ROM BOARD | ROM BOARD TEST LEDs LEDs VIDEO REMEDY RECOGNIZE IDENTIFY
CONDITION CHIPS
| GENERAL | “0” means all | - | (1) Scanning rug pattern | If any video (see left) is missing or |
| power-up tests | (2) Stationary rug | pattern | error message is displayed, proceed to | |
| passed | (3) "INITIAL 1 | INDICATE: | Diagnostic Mode tests. |
OPERATIONAL"
- Game-Over Mode
| CMOS | “QO” means tests | - | “HIGH SCORE TABLE RESET” | (1) Open coin door and turn power |
| (See Appendix A) | passed | “BOOKKEEPING TOTALS CLEARED” | off and on. |
“ADJUSTMENT FAILURE” “RESTORE FACTORY SEITINGS BY
| “OQ” means tests | - | “FACTORY SEITINGS RESTORED” | (2) Press ADVANCE. Game should |
passed return to Game-Over Mode.
| BATTERY | “Q” means tests | - | “HIGH SCORE TABLE RESET” | (1) Open coin door and turn power |
| (See Appendix A) | passed | “BOOKKEEPING TOTALS CLEARED” | off and on. Or press ADVANCE. In |
“ADJUSTMENT FAILUR! either case, game should return to “RESTORE FACTORY SEITINGS BY Game-Over Mode. OPENING FRONT DOOR AND. (2) Check AA alkaline cells on CPU TURNING GAME OFF AND ON” Board.
- If problem persists proceed with CMOS RAM test by putting the game into its Diagnostic Mode (see SELF- DIAGNOSTICS).
| MEMORY | “OQ” means tests | - | “HIGH SCORE TABLE RESET” | (1) Making and breaking coin door |
| PROTECT | passed | “BOOKKEEPING TOTALS CLEARED” | interlock switch, check with VOM |
| INTERLOCK | “ADJUSTMENT FAILURE” | and replace if faulty. | |
| (See Appendix A) | “RESTORE FACTORY SEITINGS BY | (2) Replace if faulty: Memory protect |
OPENING FRONT DOOR AND. gates 6E, IC1, Ql, or CMOS RAM TURNING GAME OFF AND ON” SPECIAL CHIP | “0 meanstests | - (1) Scanning rug pattern. passed (2) Blank screen instead of “INITIAL TESTS INDICATE: OPERATIONAL” chips one at a time with known good.
- High score table with no scores. chip:
- Intro blank or program crash. (3) Turn Machine on after each replacement and run through Power- Up Tests.
+5v DC ADJUSTMENT (R10 & R24)
Before adjusting the voltage output, always check the output at the supply for AC hum. This hum should never rise above 0.005v on the +5v DC supply. If it does, consult your schematic drawing set for proper DC voltages throughout the circuit. Test for these with the DC setting of your multimeter. Make a second check using the AC setting. Pay particular attention to readings at TP5 (top of capacitor C10). If the voltage here is too low (less than +11v DC) or you find excessive ripple (more than 700mv rms), replace the capacitor.
Table 3 Voltage Adjustments to +5v De Supply
| WHICH RESISTORS | Neither | R10 only | R24 Only | R24 &R10 |
SUPPLY HAS...
| TO INCREASE VOLTAGE | Add R24 | Remove R10 or add _ | - | Remove R10 or add |
| IF UNDER 4.25v DC... | R24 | R24 | |
| TO DECREASE VOLTAGE | Add R10 | - | Remove R24 or add_| | Remove R24 or add |
| IF OVER 5.25v DC... | R1O | RIO |
SELF DIAGNOSTICS
If RAM or ROM failure messages are displayed on the CRT after the “rug pattern” proceed with self-diagnostics. Selfdiagnostic procedures are controlled by the AUTO-UP/MANUAL-DOWN and ADVANCE switches in the coin door. Set the AUTO-UP/MANUAL-DOWN switch to the MANUAL-DOWN position and depress the ADVANCE pushbutton. The game is now in its Diagnostic Mode and a ROM test is performed. With ROM test results present on the CRT display, depressing the ADVANCE pushbutton initiates the RAM test. Further tests (CMOS, sound, switch, color RAM, monitor test patterns) are encountered one after the other as the ADVANCE pushbutton is depressed (once more for each subsequent test).
MONITOR TEST PATTERNS - For ease in monitor adjustments, the monitor may be slid back and the screen viewed in the CRT mirror provided on the inside-top of the cabinet. Remove the two bolts and carefully slide the monitor back in its shelf; secure the monitor in the extended position by inserting the two bolts though holes in the monitor base and monitor shelf provided at the left side of the monitor.
AUTO CYCLE MODE - From the color bar pattern (or Game Over with the switch set to AUTO-UP) depress ADVANCE two times to display GAME ADJUSTMENTS.
- Position the cursor on AUTO CYCLE with the MOVE Joystick and push the FIRE joystick up.
- Depress ADVANCE.
- The system will now sequence through ROM, RAM, and CMOS RAM tests repeatedly. The coin door must be open during the Auto Cycle test. If an error is detected, the test is terminated and the failure indication is displayed on the CRT.
- To terminate the Auto-Cycle test, turn the game OFF and ON.
EEIEIE|
elalalelald
BBE EE Figure 4. RAM Location and Numbering on the CPU Board
DIAGNOSTIC MODE RAM AND ROM TESTS ROM BOARD ROM BOARD TEST LEDs LEDs VIDEO REMEDY RECOGNIZE IDENTIFY CONDITION CHIPS ROM “2” means ROM 2-digit ROM “ROM ERROR” and ROM chip no. (1) Turn power off. error. chip number (2) Replace suspected chip. RAM “1” means RAM Bank number “RAM ERROR” followed by RAM (1) Check for normal voltages on error. first... then bank number and chip number (Note: | indicated RAM chip: -5v/pin 1, chip number in| with multiple RAM failures this +12v/pin 8, +5v/pin 9. sm (see figure | display may not appear) (2) Turn power off.
- Replace suspected chip.
- With multiple RAM failures. always check power supply. See POWER-UP TESTS. CMOS “3” means CMOS | - “CMOS RAM ERROR OR WRITE (1) Check pin 22 of CMOS RAM (See Appendix A) | RAM error PROTECT FAILURE” for +3.8VDC. If present, replace CMOS chip IC. If absent replace AA alkaline cells.
- With new alkaline cells, check for +3.8VDC. If still absent, replace diodes D9 and D10.
- Upon power-up and re-entry into diagnostics if CMOS error message persists check CMOS RAM memory protect and address decoding circuits with a logic probe.
Tests 4 and 7 provide sequential subtests. To stop automatic cycling set switch to MANUAL-DOWN Depress advance in MANUAL-DOWN to step through subtests. LED indications are not made for these tests.
TEST & PROCEDURES VIDEO REMEDY OR ADJUSTMENT
SOUND “SOUND LINE 1” Missing Check (Test 4) “SOUND LINE 2” 1 2P4/IOP3 Pin 3 “SOUND LINE 3” 2 2P4/10P3 Pin 2 “SOUND LINE 4” 3 2P4/10P3 Pin 5 “SOUND LINE 5” 4 2P4/10P3 Pin 4 “SOUND LINE 6” 5 2P4/10P3 Pin 7 (These appear one at a time) 6 2P4/10P3 Pin 6 All Perform Sound Board Diagnostics (see below) SWITCH TEST CRT indicates AUTO-UP closed and any stuck | (1) COIN DOOR SWITCH STUCK: (Test 5) switches. CRT Display for Each Switch ... Disconnect 2P3
- Set switch to MANUAL-DOWN and clear any stuck switches.
- CRT should indicate no switches closed.
- Operate switches and check for display of switch name. Coin Door Player Panel
ADVANCE 1- PLAYER START AUTO-UP 2- PLAYER START HIGH SCORE RESET MOVE UP LEFT COIN MOVE DOWN CENTRE COIN MOVE LEFT RIGHT COIN' MOVE RIGHT SLAM SWITCH FIRE UP FIRE DOWN FIRE LEFT FIRE RIGHT
- PLAYER PANEL SWITCH STUCK: Disconnect 3P2 or 3P3
- COIN DOOR SWITCH DOES NOT OPERATE: Ground corresponding pin of 2P3.
- PLAYER PANEL SWITCH DOES NOT OPERATE: Ground corresponding pin of 3P2 or 3P3
SYMPTOM REMAINS SAME... ROM Board or Interface Board Faulty. SYMPTOM CLEARS UP... Problem is in switches or wiring
MORE DIAGNOSTIC MODE TESTS
TEST & PROCEDURES VIDEO SEQUENCES REMEDY OR ADJUSTMENT
COLOUR RAM TEST (Test 6)
- CRT sequences through 8 colors, 2 seconds each
- Thick vertical band indicates color RAM fault. 1 Light red screen 2 Red screen 3 Dark red screen RAM 1B RAM 2B Too-light or Magenta band too dark red or gray band 4 Light green screen | Yellow band Cyan band 5 Green screen 6 Dark green screen 7 Light blue screen Magenta band Too-light or too 8 Blue screen dark blue or gray band 4 Light green screen | Green band Dark green band or gray band 5 Green screen Light green band Dark green band or gray band 6 Dark green screen : Grey band MONITOR & COLOUR RAM TEST (Test 7)
8=MAGENTA Color Bar Pattern Cross hatch pattern Aids you in setting up vertical and horizontal linearity, convergence and focus.
Red screen Green screen Blue screen Color Bars Aids you in optimizing color purity
Color Bars
- Double-width
- Half-width
- Transposed
- Missing If color RAM test 6 indicates no faults, symptoms at left suggest a fault in 1A, 1B, 2B or 2C chips.
SOUND BOARD DIAGNOSTICS
Depress the DIAGNOSTIC pushbutton on the bottom of the Sound Board. A check is made of the Sound ROM and sounds are produced if the check is good. If sounds are produced but not in Audio Test 5 check for ROM board PIA output on Sound Board inputs that are stuck low. If no sound is produced either the Sound ROM, IC12, input power, or other Sound Board circuitry is faulty.
CMOS RAM Data Test Protocol
The first sub-test of the CMOS RAM data is that of the ATTRACT MODE MESSAGE checksum. If the test does not pass, the factory ATTRACT MODE MESSAGE is restored. Next, the game adjustments are checked and restored to factory settings if an error is found. If game adjustments are found intact, the high score table is checked for any bad entries. Bad entries are replaced with a score of 4,000 points and no initials. If all entries check, the game returns to the Game Over Mode.
If game adjustments are restored to factory settings, the AUDIT TOTALS are checked. If 5 or more audit digits are other than 0-9 (that is hexadecimal A through F) all audit totals are cleared. This is followed by a check of the high score table and the table is reset to factory settings if errors are found. Finally, game adjustments are rechecked and either OPEN COIN DOOR or FACTORY SETTINGS RESTORED is displayed. With the former, open the coin door and turn the game OFF and ON and then FACTORY SETTINGS RESTORED will be displayed. Return to game over by depressing the ADVANCE pushbutton or by turning the game OFF and ON a second time. APPENDIX A
> FAIL
RESTORE FACTORY MESSAGE
RESTORE FACTORY SETTINGS.
5 OR MORE HEX A-F
CLEAR AUDITS
FAIL, PASS.
RESET HIGH SCORE TABLE ‘TO FACOTRY SETTINGS.
FAIL PASS:
"OPEN COIN DOOR" DISPLAYED.
OPEN COIN DOOR POWER OFF AND ON o PASS
BAD ENTRIES REPLACED WITH 4,000 AND NO INITIALS }—_ “INITIAL TESTS INDICATE ALL. SYSTEMS GO" DISPLAYED
FACTORY SETTINGS RESTORED DISPLAYED
POWER ON AND OFF.
s
“Warning: This equipment generates, uses, and can radiate radio frequency ener gy and if not installed and used in accordance with the instructions manual, may cause interference to radio communications. As temporarily permitted by regulation it has not been tested for compliance pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference. Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures may be required to correct the interference.”