Street Fighter II Aplha 2
Street Fighter Alpha 2 (Europe 960229) (Capcom, 1996) · Manual · 22 pages · 13 sections · original scan
CAPCOM CO., LTD. 1996 ALL RIGHTS RESERVED
OPERATORS MANUAL
/\\, WARNING
This game is for use in the United States of America and Canada. Sales, export or operation outside of these countries may be constructed as copyright and trademark infringements and is strictly prohibited. Violators are subject to severe penalties and will be prosecuted to the full extent of the law.
CARCOMY COIN-OP, INC. 3311 N. Kennicott Avenue Arlington Heights, Illinois 60004 Phone: (847) 797-6100 PM00157-KIT Fax: (847) 797-6306 031996
CANPEOM com-op, inc. STREET FIGHTER™ : ALPHA 2
THANK YOU FOR PURCHASING A STREET FIGHTER ALPHA 2™ VIDEO KIT. WE INVITE YOU TO USE THE FOLLOWING MAILING ADDRESS, TELEPHONE OR FAX NUMBER FOR PARTS OR SERVICE INFORMATION CONCERNING THIS GAME:
CAPCOM® COIN-OP, INC. ATTN: FIELD SERVICE - VIDEO PRODUCTS 3311 N. KENNICOTT AVENUE ARLINGTON HEIGHTS, ILLINOIS 60004 PHONE: (847) 797-6100 FAX: (847) 797-6306
THE SERIAL NUMBERS OF YOUR KIT ARE LOCATED ON THE GAME CARTRIDGES AS SHOWN BELOW. PLEASE HAVE THESE SERIAL NUMBERS AVAILABLE WHEN CONTACTING US FOR SERVICE INFORMATION.
AAMA BRCARTRIDGE SERIAL NUMBER SERIAL NUMBER
"A" CARTRIDGE SERIAL NUMBER (BOTTOM OF CASE) ‘300900
DEPENDING ON THE TYPE OF KIT YOU PURCHASED, PLEASE RECORD THE SERIAL NUMBERS HERE:
“FULL” KIT A-CARTRIDGE SERIAL # B-CARTRIDGE SERIAL # AAMA SERIAL #
“B” KIT B-CARTRIDGE SERIAL # AAMA SERIAL #
Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.
CAPCOM? coin-op, inc. STREET FIGHTER™ : ALPHA 2
TABLE OF CONTENTS
Warranty Information
Kit Inspection
Kit Installation “FULL” Kit Preparation Installation Marquee System Wiring Test Bracket Game Cartridge(s) “B” Kit Preparation and Installation oo.eeeeesessssssseseseseseeseseeeeecseceeseneseeeeeeesnseeseateeseeseseeneeeee 7
Test Mode Test Menu Accessing the Menu How to Select an Item Closing the Menu Menu Item Descriptions Configuration Menu System Configuration Game Configuration wWBNKDOWM”MO
Cable Wiring JAMMA Connections Auxiliary Cable Connections
Template : Control Panel Drill Hole(s)
Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC. i
CAP@ONL co-op, inc. STREET FIGHTER™ : ALPHA 2
LIMITED PRODUCT WARRANTY (APPLIES TO DOMESTIC SALES ONLY)
CAPCOM® COIN-OP, INC. (Seller), warrants only to the initial purchaser of its products, that the items listed below are free from defects in material and workmanship under normal use and service for the warranty periods specified:
A. CPS II System Cartridges One (1) Year B. Electronic and Mechanical Components: (90) days
No other part of Seller's products are warranted.
Warranty periods are effective from the initial date of shipment from seller to its authorized distributors.
Seller's sole liability shall be, at its option, to repair or replace products which are returned to Seller during the warranty periods specified, provided:
A. Seller is notified promptly upon discovery by buyer that stated products are defective;
B. Such products are properly packaged and then returned, prepaid to Seller's designated plant.
This warranty does not apply to any parts damaged during shipment or handling, or due to improper installation or usage, or alteration. In no event shall Seller be liable for any anticipated profits, loss of profits, loss of use, incidental or consequential damages or any other losses incurred by the customer in connection with the purchase of a CAPCOM® COIN-OP, INC. product.
WARRANTY DISCLAIMER
EXCEPT AS SPECIFICALLY PROVIDED IN A WRITTEN CONTRACT BETWEEN SELLER AND PURCHASER, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
THIS SHIPMENT HAS BEEN CAREFULLY INSPECTED AND PROPERLY PACKAGED BEFORE LEAVING THE FACTORY. WE CANNOT ASSUME RESPONSIBILITY FOR BREAKAGE THAT MAY OCCUR DURING TRANSPORTATION OF THE GAME. IF THIS GAME IS DAMAGED UPON RECEIPT FROM THE CARRIER, IMMEDIATELY NOTIFY THE CARRIER AND FILE A DAMAGE REPORT.
ii Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.
CANP@@NI* coin-op, Inc. STREET FIGHTER™ : ALPHA 2
KIT INSPECTION
There are two kits available for conversion to STREET FIGHTER™ : ALPHA 2
- SFAT1000 (“FULL” kit) contains the complete game cartridges, all necessary graphics, and replacement joysticks and button switches. The “FULL” kit is intended for conversion of most JAMMAcompatible, horizontal screen cabinets.
- SFAT1000B (“B” kit) contains the game software cartridge (B-cartridge) and must also be installed to a current CAPCOM® System II game. It includes all the necessary game graphics for a cabinet conversion (marquee, control panel overlay, monitor card, etc.).
Check that all parts have been shipped with your kit. If any parts are missing, contact your distributor immediately.
KIT PARTS LIST
SFA1000 | SFA1000B | PART NO. DESCRIPTION v A-00653 CPS II System Cartridges (A/B ) A-00654 CPS II System Cartridge (B ) GE1200 Monitor Card AW00209 Marquee AW00145-1 Overlay, Control Panel AW00211 Decal, Joystick & Button Switches AW00212 Decal, Cabinet Side AW00210-01 Decal - Top, Instruction AW00210-02 | Decal - Btm., Instruction PM00157-KIT | Manual, Operators 03-0052 Cable, Auxiliary GE2030 Joystick 16-0130 Switch, 1-Player Start Button (White) 16-0131 Switch, 2-Player Start Button (White) 16-0133 Switch, Button (Red) 16-0134 Switch, Button (Blue) 16-0136 Switch, Button (Green) 03-0050 Bracket, Volume/Test 13-0066 Bracket, A-Cartridge Mounting SC00104-05 Screw, Wood tH Alfalofalala}o}atr|afa/a}a}ro]aj/afajajaja
[Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC, 1
CARGO coin-op, inc. STREET FIGHTER™ : ALPHA 2
[ CAUTION |
Please read the following instructions to keep the PC board in good condition:
#Do not block the ventilation slots.
#Do not drop or bump the board.
Do not spill any liquids on the case.
Do not disassemble the case.
ATTENTION
The product that you have purchased contains a recyclable battery. At the end of its useful life, under various state and local laws, it may be illegal to dispose of this battery into the municipal waste system. Check with your local solid waste official for details in your area for recycling options or proper disposal.
DISASSEMBLING THE CASE OR REMOVING THE STICKER MAY CAUSE THE TERMINATION OF YOUR REPAIR WARRANTY
OF YOUR REPAIR WARRANTY.
2 Pr ‘and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.
CAPCOM’ coin-op, Inc. STREET FIGHTER™ : ALPHA 2
“FULL” KIT INSTALLATION
AN WARNING:
MAKE SURE ELECTRICAL POWER TO THE GAME IS OFF BEFORE STARTING THE KIT INSTALLATION.
PREPARATION
- Disconnect and remove the old printed circuit board(s) from the cabinet.
- Remove or open the control panel, and disconnect and remove the buttons and joystick(s) from the control panel.
- Remove any covering from the control panel overlay, and then remove the control panel overlay.
- Place the Drill Hole Template (included in this manual) over the control panel to determine where any new holes should go. Center punch any needed new holes on the control panel.
- Cut out the new holes using a 1-3/16" hole saw.
- If there is an additional control panel cover (such as plastic or lexan) that will be utilized, cut any additional holes using the same template.
- Plug up unused holes with wood dowel (1-1/8" diameter), being careful to sand any rough edges, or use available button plugs.
INSTALLATION
Marquee Installation
- Remove the marquee glass, old marquee overlay, and the old cabinet graphics.
- Install the new marquee and replace the glass.
Control Panel Overlay Installation (See Figure 1)
- The control panel overlay in the kit is oversized to accommodate most control panel sizes. Center the overlay on the control panel, leaving some excess material at the edges.
- Remove the protective backing from the overlay and press it down on the control panel, keeping it properly aligned. Press it down firmly, smooth out any bubbles, and press it over the edges.
- Trim any excess from the overlay. Place the drill hole template on top of the overlay, aligning it with the joystick holes. Pierce through the overlay at each control panel hole. Then, cut away overlay material covering the joystick and button holes. Remove the template and clean off the overlay.
- Peel off the backings of the 6-button and joystick decals, align over the control panel holes, and press in place on the overlay (refer to the drill hole template for proper placement). Using a knife, trim material from the center hole of the joystick decal.
- Install the control panel cover (if required).
Control Panel
Figure 1 Overlay Installation Reassembly of Components
- Install all buttons and retaining rings on the control panel as shown in Figure 2. Install two RED buttons to the immediate right of each joystick, install two GREEN buttons to the right of the red ones, and install two BLUE buttons to the right of the green ones.
[Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC. 3
@AP@ON° coin-op, INC.
Control Panel Red Green Blue uh a
orice Red Green Blue
Red Green Blue Red Green Blue eS Buttons. = al ~ U
Retaining Rings ———— Switches. ae FIGURE 2 Control Panel Buttons and Switches
- Notice that there are two white buttons. (See Figure 3.) Install the PLAYER ONE button on the top left-hand side of the control panel, and the PLAYER TWO button on the top right-side of the control panel. The WHITE buttons are START buttons.
1 Player
FIGURE 3 Function and Start Buttons
- Install the switched on the buttons as shown in Figure 2. Orient the switches so that when a button is pressed, the red contact on the switch is depressed.
- Install the joysticks on the control panel as shown in Figure 4.
Wiring
FIGURE 4 Joystick Installation
connector and the appropriate control or switch wire on the normally-open connector of the switch.
- Reconnect the existing JAMMA connectors to the control panel according to the chart of Figure 5S.
- Connect the Player 1 and Player 2 Kick buttons to the auxiliary cable harness connectors shown in Figure
- Make the connections according to the chart of Figure 7.
TO GAME CASE CONNECTOR
TO PUSH-BUTTON ‘SWITCHES
TO VOLUME & TEST SWITCHES
FIGURE 6 Auxiliary Cable Harness
4 [Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.
@APCOM’ coin-op, inc. STREET FIGHTER™ : ALPHA 2
JAMMA CONNECTS
CONNECTOR REF. | *WIRE COLOR TO
rs PLAYER 1 JOYSTICK
PLAYER 1 JOYSTICK DOWN PLAYER 1 JOYSTICK LEFT
| PLAYER 1 | JOYSTICK | LEFT. |
PLAYER 1 JOYSTICK RIGHT
| PLAYER 1 | PUNCH BUTTON | JAB |
| PLAYER 1 | PUNCH BUTTON | STRONG |
PLAYER 1 PUNCH BUTTON
| VIOLET/BLACK | PLAYER 2 | JOYSTICK | |
| VIOLET/BROWN | PLAYER 2 | JOYSTICK | |
| VIOLET/RED | PLAYER 2 | JOYSTICK | |
| VIOLET/ORANGE | PLAYER 2 | JOYSTICK | |
| VIOLET/YELLOW | PLAYER 2 | PUNCH BUTTON | |
| VIOLET/GREEN | PLAYER 2 | PUNCH BUTTON | |
| b | VIOLET/BLUE | PLAYER 2 | PUNCH BUTTON |
Figure 5: Control Panel JAMMA Wiring Connections
- Wire Color Note: Wire colors shown are according to the AAMA -AMOA Standard for wire color assignments; your harness may contain different colors than shown above.
AUXILIARY CABLE CONNECTS CONNECTOR REF. WIRE COLOR TO FUNCTION
| PLAYER | | KICK BUTTON | COMMON, | ||
| ; | tts—“‘CSC‘szC | PLAYER | | KICK BUTTON | SHORT. |
| PLAYER 1 | KICK BUTTON | FORWARD | ||
| PLAYER | | KICK BUTTON | ROUNDHOUSE | ||
| PLAYER 2 | KICK BUTTON. | COMMON | ||
| GRAY/YELLOW, | PLAYER 2 | KICK BUTTON. | SHORT | |
| PINK/YELLLOW, | PLAYER 2 | KICK BUTTON. | FORWARD | |
| PURPLE/YELLOW, | PLAYER 2 | KICK BUTTON | ROUNDHOUSE | |
| GRAY/YELLOW | TEST BRACKET | VOLUME SWITCH | UP. | |
| PINK/YELLOW | TEST BRACKET | VOLUME SWITCH | ||
| BLACK/WHITE | TEST BRACKET | VOLUME SWITCH |
Figure 7: Auxiliary Cable Wiring Connections for Control Panel and Test Bracket
[Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC, 5
CAPCOM coin-op, INC.
- An optional Test/Volume bracket (see Figure
- is included in this kit. Your cabinet may already contain this bracket. If you decide to install, the bracket should be mounted inside the coin door and on top of the cash box for easy access.
‘300500 Figure 8: Test Bracket
Wiring of the Test Bracket requires connections to both the main JAMMA harness as well as the auxiliary cable harness (refer to Figure 9).
oe FUNCTION TO VOLUME-UP | AUX. CABLE ‘29°(GRAY/ YELLOW) COMMON | AUX. CABLE ‘*31’(BLACK/ WHITE) VOLUME- AUX. CABLE DOWN ‘30° (PINK/ YELLOW) AUX. CABLE *31’(BLACK/ WHITE) TEST JAMMA ‘15’
GROUND JAMMA ‘A’
or ‘B’ or ‘e’ or “f or ‘1? or ‘2’ or ‘27’ or ‘28” Figure 9: Test Bracket Wiring Chart COMMON
[Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM@ COIN-OP, INC. STREET FIGHTER™ : ALPHA 2
GAME CARTRIDGE INSTALLATION
- Install the four (4) mounting brackets to the underside of the “A” cartridge as shown in Figure 10.
Figure 10: Mounting Bracket Installation
- Using the supplied wood screws, fasten the game cartridge case to the control panel shelf, as shown in Figure 11.
Figure 11: Case Mounting
- Connect the JAMMA harness connector and the auxiliary cable connector to the “A’ cartridge. If your cabinet is equipped with Q- SOUND, also attach the audio cables.
@AP@ON"co IN-op, INC. STREET FIGHTER™ : ALPHA 2
- Power-up the game and set all operator adjustable options by pressing the TEST switch. Follow the instructions under the TEST MENU section of this manual. 3. Power-up the game and set all operator adjustable options by pressing the TEST switch. “B” KIT INSTALLATION Follow the instructions under the TEST MENU section of this manual.
- To install the cabinet graphics, you must follow the “FULL” Kit Preparation and Installation Procedure, steps 3 through 14.
- To remove the existing “B” cartridge from the “A” cartridge, pull the old case clamps apart (see Figure 12). Carefully remove the old “B” cartridge and install the new “‘B’ cartridge. Re-install the case clamps.
"A" Cartridge
Figure 12 : Case Clamp Installation
[Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC. 7
@AP@OM" coin-op, Inc. STREET FIGHTER™ : ALPHA 2
NOTES
8 [Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, I
CANP@ON* coin-op, Inc. STREET FIGHTER™ : ALPHA 2
TEST MENU
The test menu allows you to test the functions and configure the game. These items include input devices such as joysticks, buttons and coin door or switches, output devices such as monitor, speakers and meters. Through the Test Menu you can also access the Configuration Menu, where you can change the settings of the game.
- ACCESSING THE TEST MENU
¢ For a CAPCOM® cabinet, or a cabinet with a test switch: Make sure the game is on and push the test switch. The screen shown below will appear.
° For a cabinet without a test switch: Push the blue test switch on the outside of the black plastic casing (refer to the inside back cover of the manual).
TEST
8.
9. MENU
INPUT
OUTPUT
SOUND & VOICE
COLOR
DOT CROSS HATCH
GAME DATA
CONFIGURATION
MEMORY CHECK
EXIT
SELECT = 1P UP or DOWN START =1P SHOT1
- HOW TO SELECT AN ITEM
© Use the PLAYER I JOYSTICK to move the arrow in front of the desired item and press the PLAYER I SHOT I (PUNCH-JAB)button.
- To return to the test menu, push the PLAYER ] START and PLAYER 1 SHOT 1(PUNCH-JAB) buttons simultaneously. © The test menu will always return to the screen:
- After you exit the “7. CONFIGURATION MENU” and
- After the memory is tested from the menu, “8. MEMORY CHECK”.
[Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN.OP, INC, 9
CAPE’ coin-op, inc.
- CLOSING THE TEST MENU To close the Test Menu, highlight “9. EXIT” and push the PLAYER 1 SHOT 1(PUNCH-JAB) button.
- TEST MENU ITEM DESCRIPTIONS STREET FIGHTER™ : ALPHA 2
INPUT Used to test all the input switches, such as joysticks and buttons. The “0” changes to a “1” as the button is pushed or joystick is moved. Check connections and switches in case the “0” doesn’t change to a “1” when depressed or moved.
OUTPUT Used to test the coin meter and the coin lock.
SOUND & VOICE Select a code of SOUND or VOICE with the PLAYER J JOYSTICK. Push the PLAYER I SHOT I (PUNCH-JAB) button to hear the sound of the selected code.
lRarae 7 ; COLOR Shows color bars of red, green, blue, and white. Adjust RGB and brightness to obtain the optimum color balance and solid black background.
DOT CROSS Used to test the screen size, focus and distortion. HATCH GAME DATA Coin meter and playtime information will be displayed. [FaANINGLDATIAN i= re ri CONFIGURATION _ | Used to change the game play settings. Refer to the CONFIGURATION MENU section.
MEMORY CHECK | Used to test memory. “OK” appears when each block of memory passes test, “NG” appears in case of malfunction. If “NG” appears, repeat the memory test and wait for the “OK” message. Contact your distributor if “NG” still appears.
EXIT Select this item and push the PLAYER I SHOT 1(PUNCH-JAB) button to return to game play mode.
[Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC,
CAP@ONI° coin-op, INC. STREET FIGHTER™ : ALPHA 2
CONFIGURATION MENU
The Configuration Menu is used to change various game settings such as level difficulty, credits, sound configuration, etc. These settings are stored in memory on the PCB.
The Configuration Menu is divided into 2 sections. In the SYSTEM section, you can change credits, sound, and coin door configurations. In the GAME section, you can change the play difficulty level and duration of the game.
- ACCESSING THE CONFIGURATION MENU ¢ From the TEST MENU, move the arrow to “7. CONFIGURATION” and push the PLAYER I SHOT I (PUNCH-JAB) button. The screen below will be displayed. A description of each option is explained in the table below.
- CONFIGURATION MENU
. SYSTEM
. GAME
» DEFAULT
. SAVE & EXIT
SELECT 1P UP OR DOWN START 1P SHOT1
SYSTEM | Select this item to change settings for credits, monitor flip, sound and coin door configurations. GAME Select this item to change difficulty level, damage level, time count speed, maximum number of rounds and event type. DEFAULT | Use this item to restore configuration settings to the original factory values. Press the PLAYER | SHOT I (PUNCH-JAB) and PLAYER I SHOT 2 (PUNCH-STRONG) . buttons at the same time to restore default values. SAVE & Use this to save new configuration settings and exit to the Test Menu. The message EXIT “SAVING NEW CONFIGURATION IN EEPROM” will appear while the new settings are being saved. DO NOT turn power off to the game until “SAVING” is complete and the Test Menu reappears.
Pemer ‘and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC. ll
@AR@OM° coin-op, Inc.
SYSTEM CONFIGURATION
CHANGING THE SYSTEM CONFIGURATION SETTINGS
Move the PLAYER | JOYSTICK up or down to highlight the desired option. Once the option is highlighted, move the PLAYER I JOYSTICK left or right or press the PLAYER 1 SHOT 1(PUNCH-JAB) button to select.
7-1. SYSTEM CONFIGURATION
. COIN MODE
. CONTINUE
. MONITOR
. DEMO SOUND
. SOUND MODE
. CHUTE TYPE
- EXIT
SELECT OPTION =1 MODIFY SETTING
SYSTEM CONFIGURATION ITEM DESCRIPTIONS
[. COIN MODE 2 COINS 1 CREDIT
ON
NORMAL
ON
STEREO (QSOUND)
2 CHUTES SINGLE
P UP OR DOWN P LEFT OR RIGHT P SHOT1 OR SHOT2 STREET FIGHTER™ : ALPHA 2
SELECT THE CHARGE PER PLAY.
- CONTINUE
- MONITOR SELECT ON FOR CONTINUOUS PLAY OR OFF FOR NON-CONTINUOUS PLAY. FLIPS THE POSITION OF THE SCREEN. IF THE SCREEN APPEARS UPSIDE-DOWN, CHANGE THE SETTING TO. FLIP; IF THE SCREEN APPEARS CORRECT, SELECT NORMAL.
- DEMO SOUND
- SOUND MODE
- CHUTE TYPE TURNS ATTRACT SOUNDS ON OR OFF. SELECT STEREO OR MONAURAL FOR USE WITH YOUR CABINET.
- EXIT TO SAVE THE SETTINGS AND RETURN TO THE CONFIGURATION MENU, HIGHLIGHT THIS ITEM AND PUSH EITHER THE PLAYER | SHOT 1 (PUNCH-JAB) BUTTON OR THE PLAYER | SHOT 2 (PUNCH-STRONG) BUTTON. ID COIN CHUTE TYPE.
SYSTEM CONFIGURATION OPTION SETTINGS
- COIN MODE
1 CREDIT
- CREDIT
| 1 COIN | 1 COIN | 1 COIN | ||
| 1 CREDIT | 2CREDITS | 3.CREDITS | ACREDITS | |
| 1 COIN | 1 COIN | 1 COIN | 1 COIN | 2 COINS |
| 6 CREDITS | 7.CREDITS | 8 CREDITS | 9.CREDITS | 1 CREDIT |
| 3 COINS | ‘4 COINS: | ‘5 COINS | ‘6 COINS | 7 COINS |
| 1 CREDIT. | 1 CREDIT | 1 CREDIT | 1 CREDIT | 1 CREDIT |
8 COINS: ‘9 COINS: ‘2. COINS START 1 COIN CONTINUE. [- FREE PLAY
- CONTINUE, ‘OFF.
[Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC,
@ANPEOM” coin-op, Inc. STREET FIGHTER™ : ALPHA 2
GAME CONFIGURATION
CHANGING THE GAME CONFIGURATION SETTINGS
Move the PLAYER I JOYSTICK up or down to highlight the desired option. Once the option is highlighted, move the PLAYER J JOYSTICK left or right or press the PLAYER I SHOT 1(PUNCH- JAB) button to select.
7-2. GAME CONFIGURATION
. DIFFICULTY HARD 2
. DAMAGE LEVEL MEDIUM
. TIMER SPEED SLOW
. GAME SPEED TURBO 2
MAX ROUND 3 ROUNDS
. EVENT OFF
. AUTOMATIC OFF
. EXIT
SELECT OPTION = 1P UP OR DOWN MODIFY SETTINGS =1P LEFT OR RIGHT 1P SHOT1 OR SHOT2
GAME CONFIGURATION ITEM DESCRIPTIONS
‘SETS THE GAME DIFFICULTY LEVEL
- *DAMAGE LEVEL SETS THE ATTACK DAMAGE LEVEL.
- TIMER SPEED SETS THE SPEED OF THE COUNTDOWN FOR THE TIMER DISPLAY. 4, *GAME SPEED SETS THE SPEED AT WHICH THE CHARACTERS FIGHT.
- MAX ROUND ‘SETS THE NUMBER OF ROUNDS PER MATCH 1 ROUND: WINNER OF THE SINGLE ROUND WINS. 3 ROUNDS: WINNER OF 2 OUT OF 3 ROUNDS WINS. 5 ROUNDS: WINNER OF 3 OUT OF 5 ROUNDS WINS.
- EVENT OFF- NORMAL SETTING 1 MATCH- MATCHES PLAYER WITH ONE CREDIT. A WIN OR A LOSS RESULTS IN GAME OVER (CONTINUE IS NOT AVAILABLE).
- AUTOMATIC SETS AN AUTOMATIC BLOCKING FEATURE FOR MOST CHARACTERS (USED FOR BEGINNING PLAYERS). NOT RECOMMENDED FOR MOST LOCATIONS.
- EXIT RETURN TO THE CONFIGURATION MENU. *NOTE: IN THE EVENT THAT THESE SETTINGS REQUIRE ADJUSTMENT, PLEASE CONTACT US FOR ADDITIONAL INFORMATION AND RECOMMENDATIONS FOR MAXIMUM GAME EARNINGS.
GAME CONFIGURATION OPTIONS
- DIFFICULTY
- DAMAGE LEVEL
- TIMER SPEED
- GAME SPEED
- MAX ROUND
- EVENT 1 MATCH
- AUTOMATIC FREE SELECT
NOTE: FACTORY SETTING
[Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM@ COIN-OP, INC. 13
@AP@OM* coin-op, inc.
WIRE COLOR STREET FIGHTER™ : ALPHA 2
JAMMA CONNECTIONS
SOLDER SIDE
| GND +5. VDC : +5 VDC GND.
+12 VDC
| COINLOCK2
NC. COIN LOCK2
: PNc | VIDEOGREEN | SERVICE (FREECREDIT) ff
SX *NOTE : FOR CABINETS EQUIPPED WITH CAPCOM® “ THROUGH THE A-CARTRIDGE WITH RCA-TYPE CONNECTORS. 2 PLAYER - PUNCH (FIERCE) fs COMPONENT SIDE
+12 VDC
COIN COUNTER 1 COIN LOCK 1 NC.
yikey | COINCOUNTER1] |
a
«| TEST MODE (DIAGNOSTICS) | IPLAYER -COIN 1 PLAYER - COIN
SOUND, AUDIO CONNECTIONS ARE MADE
AUXILIARY CABLE CONNECTIONS
CONNECTOR ODD ROW
NIC NIC NIC NIC PURPLE/YELLOW, 2 PLAYER - KICK (ROUNDHOUSE)
1 PLAYER - KICK (ROUNDHOUSE) 1 PLAYER - KICK (FORWARD)
GRAY/YELLOW PINK/YELLOW_ 1 PLAYER - KICK (SHORT) 2 PLAYER - KICK (SHORT) 2 PLAYER - KICK (FORWARD)
GRAY/YELLOW TEST BRKT-VOLUME UP BLACK/WHITE TEST BRKT- VOLUME COMMON BLACK 1 PLAYER _- KICK (COMMON) NIC NIC NIC
TEST BRKT-VOLUME DOWN. | NIC 1 PLAYER _- KICK (COMMON) BLACK PINK/YELLOW
[Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN. ic
1-3/4" DRILL FOR JOYSTICK HOLE 1-3/16" DRILL FOR 1P OR 2P START BUTTON SWITCH
1-3/16" DRILL FOR BUTTON SWITCH HOLES
CAPCOM COIN-OP, INC. 3311 NORTH KENNICOTT AVENUE "ARLINGTON HEIGHTS, ILLINOIS 60004 PHONE (708) 787-6100 COIN-OP, INC. FAX (708) 797-6119
DRILL HOLE TEMPLATE: "STREET FIGHTER ALPHA 2"
110100
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
CAPEOMI coin-op, INC. STREET FIGHTER™ : ALPHA 2
REFERENCE INFORMATION
GAME CASE CONTROLS
| SS COMMUNICATION PORTS (NOT USED) ¢ (Sab) OUT IN
TEST VOLUME UP VOLUME DOWN
JAMMA AUXILIARY CABLE AUDIO OUT (FOR Q SOUND) CONNECTOR CONNECTOR RIGHT: RED, LEFT: WHITE 300800
TYPICAL CONTROL PANEL LAYOUT OF STREET FIGHTER™ : ALPHA 2
[Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.
NOTICE
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.
WARNING
Federal law provides severe civil and criminal penalties for the unauthorized reproduction, distribution, or exhibition of copyrighted audiovisual works and video games.
The Federal Bureau of Investigation investigates allegations of criminal copyright infringement.
ICAIRCOMY§ COIN-OP, INC. 3311 N. Kennicott Avenue Arlington Heights, Illinois 60004 Phone: (847) 797-6100 Fax: (847) 797-6306
Copyright © 1996 CAPCOM ® coin-op, INC., All Rights Reserved