Power Drift
Power Drift (World, Rev A) (Sega, 1988) · Manual · 25 pages · 11 sections · original scan
UPRIGHT YZ TYPE (W/O MOTOR)
OWNER’S MANUAL
kK SEGA ENTERPRISES, LTD. DN
DS APBDZDRRODIAPLOYDARLEER A
TABLE OF CONTENTS
Introduction to the Owner’s Manual . Handling Precautions .........0....... . Prevention of Counterfeiting and Conversion . Precautions Concerning the Place of Installation . Name of Parts ...........0064 . Servicing the Handle Unit . . Disassembling and Adjusting the Handle Uni . Disassembling and Adjusting the Accelerator and Brake . Adjusting the Accelerator/Brake Potentiometer . . Adjustment of the Service Switch . DIP Switch Setting . EPROM/ROM Locations . Test Mode .... . Parts List .. . Schematic Diagram . SeEMIDMNAWNE Meee RWNHE WCeoONURWWNNE
SPECIFICATIONS
INSTALLATION SPACE : 700 mm (27.6 in.) W x 550 mm (21.6 in) D HEIGHT : 1650 mm (65.0 in.) POWER : 145 W C.R.T. : 19" MONITOR WEIGHT : 95 kg (209.4 lbs.)
- Descriptions herein contained may be subject to improvement changes without notice.
INTRODUCTION TO THE OWNER’S MANUAL
SEGA ENTERPRISES, LTD.., supported by its high electronic technology of LSIs, microprocessors, etc. and a wealth of experience, has for more than 30 years been supplying various innovative and popular game machines to the world market. This OWNER’S manual is intended to provide detailed comments together with all the necessary information covering the operation in general of electronic assemblies, electromechanicals, servicing control, spare parts, etc. as regards the POWER DRIFT, a new SEGA product. The manual is intended for those who have knowledge of electricity and technical expertise especially in ICs, CRTs, microprocessors, etc. Carefully read so as to acquire sufficient knowledge before working on the machine. Should there be a malfunction, non-technical personnel should under no circumstances touch the interior system.
- HANDLING PRECAUTIONS
When installing or inspecting, be very careful of the following points and pay attention to ensure that the player can enjoy the game safely. ¢ Be sure to turn the power off before working on the machine.
- To insert or pull out the plug quickly is dangerous.
- Itis necessary to make sure that the power cord or the grounding wire is not exposed on the road, etc. in a manner so as to be dangerous. Make sure that grounding connections are made safely at the position where so specified.
- Do not use any fuse that does not meet the specified rating.
- Make complete connections for the IC board and other connectors. Insufficient insertion is very dangerous.
Also, for the IC board circuit inspections, only the logic tone is allowed. The use of a tester is not permitted, so be careful in this regard. After confirming that there are no irregularities, turn the power ON.
- PREVENTION OF COUNTERFEITING AND CONVERSION
LABELLING To prevent counterfeits and conversions, the following labels are put on all the SEGA products. When handling such goods, be sure to confirm the labels. They are used to prevent illegal acts such as the unauthorized copying of the products and the printed circuit boards thereof or carrying on business by manufacturing similar merchandise or by converting, selling or using such products or printed circuit boards.
LICENSE SEAL ORIGINAL SEAL The following seal is put on the The following seal is put on the machines manufactured by kits , such as the printed circuit boards SEGA. of SEGA products.
SEGA: AU YF MEE : [ORIGINAL SEAL Sorsicwto
COPYRIGHT NOTICE This SEGA product has the copyright notice as follows: © SEGA 1988
This signifies that this work was disclosed in 1988 and is the property of SEGA ENTERPRISES, LTD.
- PRECAUTIONS CONCERNING THE PLACE OF INSTALLATION
The POWER DRIFT is an indoor game machine. Absolutely do not install it outside. Even indoors, avoid installing in places mentioned below so as to ensure proper usage: Places subject to rain or water leakage, or condensation due to humidity. + In the proximity of an indoor swimming pool and/or shower. ¢ Places subject to direct sunlight. + Places subject to heat sources from heating units, etc., or hot air. ¢ Vicinity of highly inflammable/volatile chemicals or hazardous matter.
- Sloped surfaces. + Vicinity of anti-disaster facilities such as fire exits and fire extinguishers.
- Places subject to any type of violent impact. + Dusty places.
- NAME OF PARTS
DESIGN PLATE POWER DRIFT 4231-0091
19" MONITOR ASSY 2000-5090 ASSY CONTROL PANEL WINDOW GLASS POWw-20002 POW!-1713
DECAL RTSIDE . SHIFT LEVER UNIT POW!-1701-8. POW-2745
START BUTTON 509-5218
COIN DOOR 2200-0000
ASSY ACCEL & BRAKE POW-2617 a
TOOLS
(TAMPERPROOF WRENCH) (TAMPERPROOF DRIVER)
M4 540-0006-01 M4 540-0018 M5 540-0007-01 M5 540-0017 M6 540-0015-01 M8 540-0009-01 Se
- SERVICING THE HANDLE UNIT AND WINDOW MASK
EMBLEM HL-2010
M8X30 TAMPERPROOF — SHIFT LEVER UNIT SCREW 029-0217 (4ea) mi POW-2745 START SWITCH [ I 509-5218 ~~ caer CONTROL PANEL COVER f POW-2743 —_—. TOP PLATE POW-2732 | ASSY CONTROL PANEL POW-20002 STEERING WHEEL KR-1121X
@ The HANDLE UNIT can be opened towards you by removing the 4 M8 x 40 TAMPERPROOF SCREWS.
@® Toremove the WINDOW GLASS from the cabinet, take off the TAMPERPROOF screws (M5) inside the WINDOW GLASS. K.
@® Next open it towards you.
This allows for the clearing of the monitor screen (CRT surfaces). ]
- DISASSEMBLING AND ADJUSTING THE HANDLE UNIT
To open the dashboard, take off the 4 M8 TAMPERPROOEF screws. After doing this, spring replacements and steering adjustments can be made.
POW-20002 Control Panel Assy
@ 220-5130 5K Potentiometer KR-1129 Gear D (Pot. Gear) (Between Arm Plates) 601-6172 Gear 48 POW-2745 Shift Lever Assy (see Shift lever Assy) KR-1126 Gear A POW-2729 _ Exit Spring KR-1127 Gear B POW-2708 Arm Plate KR-1127 Gear B POW-2704 Steering Shaft KR-1115 Stopper POW-2706 Bumper Bracket POW-2707 Bumper Stopper KR-1114 Bumper POW-2734 Braked Cam 100-5035 Bearing (Steering Shaft) KR-1109Y Arm Bar QQOQOOOOEOQOOEHOGO
@ Release the 2 adjusting screws of the potentiometer bracket and perform the necessary adjustments by changing its gear position, making sure that the variable is within the allowable extent as shown below, and then retighten the adjusting screw.
POTENTIOMETER BRACKET POTENTIOMETER
ADJUSTMENT SCREW
Standard value & © Minimum Go) |7F 80H 81H | Maximum 0) > « Allowable adjustment range >
Assembly Shift Lever Unit YZ Type POW 2745 @ POW-2740 Sub Assy Shift Lever (@) POW-2732 Cover “B” @) POW-2730 Guide Plate @ POW-2202 Transmission Case “B” @® POW-2206 Stopper Rubber @® POW-2204 Stopper Shaft “A” @) POW-2207 Cam POW-2210 Extension Spring @) POW-2208 Hook @ 509-5088 Micro Switch @ POW-2201X Transmission Case “A” © POW-2739 Stopper Shaft “B” ®@ POW-2206 Stopper Rubber @ 100-5018 Ball Bearing 8 @ POW-2731 Cover “A”
| 000-0316 | 2ea | _M3x16 Phillips Screw | |
| 000-0510-5 | 4ea | = M5x10 Phillips Screw | |
| 000-0416-5 | 2ea | M4x16 Phillips Screw | |
| 065-0007 | 6ea | = 7mm E-Ring | |
| 061-0006 | lea | M6 | Spring Washer |
| 060-0008 | Sea | M8 | Flat Washer |
| 054-0006 | 2ea | = M6 | "U" Nut |
Control Panel Assy Hardware List (POW-20002)
PART No. Q/U_ DESCRIPTION
000-0408-FS 2 000-0416-FS 4 000-0508 000-0510 000-0516 001-0516 001-0520 029-0152 008-0415 008-0425 028-0007 028-0010 028-0014 000-0312-FS 030-0825 030-0630 045-0004 045-0005 050-0012 054-0005 054-0006 080-0005 060-0006 060-0008 060-0010 069-0020 061-0006 061-0008 061-0012 069-0022 028-0012 029-0078 045-0014 006-3113 054-0004 030-0620 000-0525-FS 061-0005 051-0004 059-0014 090-0012 090-0013 005-3516-F 069-0084 008-0420 059-0002 000-0516-FS 008-0516 ar NUON
aor
=
nS PRNNENERANNNNANE WEEE EDAE RE RIUDISDENODANANWHEAW MSCR PH W/FS M4 x 8 M SCR PH W/FS M4 x 16 M SCR PH W/EFS M5 x 8 M SCR PH W/FS MS x 10 MSCR PH W/S MS x 16 MSCR FH M5 x 16 MSCR FH MS x 20 TMP PRF SCR TH CROME MS x 12 TMP PRF SCR TH M4 x 16 TMP PRF SCR TH M4 x 25 SET SCR HEX SKT CP UNBR M4 x 10 SET SCR HEX SKT CP M5 x 8 SET SCR HEX SKT CP UNBR M4 x 4 M SCR PH W/FS M3 x 12 HEX BLT M8 x 25 HEX BLT M6 x 30 COT PIN 1.6 x 15 COT PIN 2 x 15 HEX NUT M12 U NUT MS U NUT M6 FLT WSHR M5 FLT WSHR M6 FLT WSHR M8 FLT WSHR M10 FLT WSHR M12 SPR WSHR M6 SPR WSHR M8 SPR WSHR M12 FLT WSHR 5.5 - 14x 1 SET SCR CH SPCL M5 x 12 TMP PRF SCR BH M6 x 16 SPR PIN UNBR 3 x 26 W SCR FH 3.1 x 13 U NUT M4 HEX BLT M6 x 20 M SCR PH W/EFS MS x 25 SPR WSHR M5 FLG NUT M4 WELL NUT M4 SCREW LOCK (Three Bond K01C — 2009 RED) GREASE (SHYOWA SHELL SEKIYU RETINAX A) W SCR RH W/F 3.5 x 16 E RING 19mm TMP PRE SCR TH M4 x 20 FLT WSHR 5.5 - 19 x 1.2 M SCR PH W/ES M5 x 16 TMP PRF SCR TH MS x 16
- DISASSEMBLING AND ADJUSTING THE ACCELERATOR AND BRAKE
To remove the accelerator/brake unit, take off the 7 M5 TAMPERPROOF SCREWS.
Assembly Accelerator & Brake (POW-2617) ®
@® 220-5130 SK potentiometer
® 601-5410 Gear 15 @ 6 (Pot. Gear)
® POW-2610 Adjust Gear
@® POW-2615 Extension Spring
® POW-2611 Center Spring
| 000-0314-F | 2ea | M3x14 Phillips Screw | |
| 000-0408-F5 | 10ea | M4x8 | Phillips Screw |
| 000-0510 | 4ea__ | M5x10 Phillips Screw | |
| 008-0510 | Sea | | M5x10 Tamperproof Screw | |
| 028-0002 | 4ea_ | M3x6_ | Set Screw (Phillips) |
| 029-0200 | 4ea | = _M3x8_ | Tap Screw (Phillips) |
| 030-0410 | 4ea | _M4x10 Hex Bolt | |
| 045-0007 | 2ea | —_M3x30 Cotter Pin | |
| 054-0003 | 2ea | M3 | “U” Nut |
| 054-0005 | Sea | MS | = “U” Nut |
| 060-0004 | 4ea | M4 — Flat Washer | |
| 061-0004 | 4ea | M4 | Spring Washer (Lock-Washer) |
| 069-0020 | 2ea | M12 | Flat Washer |
- ADJUSTING THE ACCELERATOR/BRAKE POTENTIOMETER
@ DISPLAY THE SELF-TESTING MODE screen shown on page 15.
@ Release the adjustment screws, move the bracket, and make adjustments so that the variable becomes 20H when the accelerator/brake is released and returns to its original Position.
® Even after the above procedure has been followed, if the variable is not within the allowable range, then slightly turn the gear to make an adjustment.
ACCELERATOR BRAKE
POTENTIOMETER POTENTIOMETER
ACCELERATOR
Minimum Standard Maximum (fully openy
- & (CO)
1CH_ 1DH 1EH 1FH 20H 21H 22H 23H 24H] >
BRAKE
- > Allowable adjustment range > (CO)
- ADJUSTMENT OF THE SERVICE SWITCH
The layout as shown below can be viewed by opening the coin chute door.
VOLUME CONTROL
SERVICE SWITCH
TEST SWITCH
OPERATING INSTRUCTIONS
SERVICE SWITCH .......ceeeeceeeeeeee es Used for the purpose of servicing and increasing the credits without registering on the meter (this allows you to check the game).
TEST SWITCH ...........ccccceeeeeeeeeeees For operating this switch, see SELF-TESTING.
VOLUME CONTROL ...........ccceeeeeeee Potentiometer Adjustment
- DIP SWITCH SETTING
COIN/CREDIT OPTION SWITCH SETTING DIP SWITCH A
OPTION
1COIN 1 CREDIT 1COIN 2CREDITS 1.COIN 3 CREDITS 5COINS. 1 CREDIT 6 COINS. 1 CREDIT 1 COINS 6 CREDIT 2COINS 1 CREDIT 3.COINS 1 CREDIT 4 COINS 1 CREDIT 2COINS SCREDITS 6 COINS 4 CREDITS 4 COINS. SCREDITS 5.COINS 6 CREDITS 4 COINS. S CREDITS 2.COINS S CREDITS
‘COIN SW. #1 COIN SW. #2
POWER DRIFT PCB ASSY (834-6697-04)
DIP SWITCH “B"
DIP SWITCH “A”
GAME OPTION SWITCH SETTING DIP SWITCH B wamoneme [> [e[>[-T [ef T+
| MOVING | OFF | OFF | |
| * CABINET | UPRIGHT | ON | OFF |
TYPE MINI UPRIGHT | OFF | ON
| NO USE | ON | ON |
- ADVERTISE OFF SOUND ON
- INITIAL, 2CREDIT CREDIT 1 CREDIT
- CONTINUE YES OFF ON GAME NO. ; NORMAL, ger | or * When DIP Switch B. 5 is set to SOEEICULTY = oe oF] “ON”, also set DIP SWITCH B. 6 HARDEST ON to “ON”.
ll
- EPROM/ROM LOCATIONS
837-6696 | Q 1 o 0 VIDEO BD
O of of D Of of a 834-6697 GAME BD POWER DRIFT = = 837-6695 CPU BD POWER DRIFT IC LOCATION | NUMBER MAIN WORK a 1 IC 24 EPR-11745 837-6695 2 Ic 25 EPR-11746 3 IC 26 EPR-11747 CPU BD POWER DRIFT 4 IC 27 EPR-11748 PROGRAM 5 Ic 53 EPR-11749A 6 IC 54 EPR-11750A 7 IC 80 EPR-11751 8 IC 81 EPR-11752 9 Io 102 EPR-11753 | SOUND PROGRAM CPU BD POWER DRIFT 837-6695 to | IC 107 | EPR1i892 (2M EPROM) "1 IC 106 EPR-11893 SOUND DATA 12 IC 105 EPR-11894 837-6696 VIDEO BD POWER DRIFT 13 Ic 16 EPR-11789 14 Ic 14 EPR-11791 LINE OBJ 15 Ic 67 EPR-11757 16 IC 75 EPR-11758 17 IC 86 EPR-11759 18 Io 114 EPR-11760 19 Ic 66 EPR-11761 20 Ic 74 EPR-11762 21 IC 85 EPR-11763 22 Io 113 EPR-11764 OBJECT 23 Ic 63 EPR-11773 24 Ic 71 EPR-11774 25 Ic 82 EPR-11775 26 Ic 110 EPR-11776 27 Ic 62 EPR-11777 28 iC 70 EPR-11778 29 IC at EPR-11779 30 IC 109 EPR-11780 31 Ic 17 EPR-11790 32 Ic 15 EPR-11792 LINE OBJ 33 IC 65 EPR-11765 34 IC 73 EPR-11766 35 IC 84 EPR-11767 36 Ic 112 EPR-11768 37 Io 64 EPR-11769 38 Ic 72 EPR-11770 39 IC 83 EPR-11771 40 Io 411 EPR-11772 OBJECT o 41 Ic 61 EPR-11781 LJ 16|20] 34)38] 24| 28/42/46 42 Ic 69 EPR-11782 43 ic 80 EPR-11783 17}2113e)9] 24 aolaaler 44 IC 108 EPR-11784 i] 45 IC 60 EPR-11785 [ 4} ic 63 | EPR-411786 ef a 26 a0|4alea 47 ic 79 EPR-11787 co oO 48 Ic 107 EPR-11788 OBJECT
- TEST MODE
This test mode verifies that the game board is correctly operating or if there are any malfunctions. Color and sound adjustments can also be tested using the test mode.
- SELECTION OF INDIVIDUAL TEST
- Push the TEST SW and the following test menu will be displayed:
DIAGNOSTIC VER. 1.00
INDIVIDUAL MEMORY TEST INPUT TEST OUTPUT TEST MOTOR TEST SOUND TEST CR.T. TEST DIP SWITCH ASSIGNMENT BOOKKEEPING BACKUP RAM CLEAR 3 EXIT
TEST ITEMS DESCRIPTION
- INDIVIDUAL... eens INDIVIDUAL/CONTINUE mode change.
- MEMORY TEST ..........eeeeeeeees Tests the game board’s memory IC’s.
- INPUT TEST ..........cccceeceeeeee Checks the numerical value of each switch, steering handle, etc.
- OUTPUT TEST.... Checks the “ON” and “OFF” of the START SW LAMP and COIN SOLENOID.
- MOTOR TEST ............0.cc00000 Tests in this mode are not applicable for the type.
- SOUND TEST ..............ccceeeee Checks the SOUND ROM and POWER AMPLIFIER.
- CR.T. TEST 00... eeecceee eee Checks the monitor adjustment color bar display.
- DIP SWITCH ASSIGNMENT ... Displays the DIP SW setting status.
- BOOKKEEPING ... .. Displays the records of the number of game plays, game time, etc.
- BACKUP RAM CLEAR.......... Clears the records of the number of game plays, game time, etc.
.... Returns to the ordinary game screen.
- Turning the steering handle to the right/left will cause the * mark to move upward/down. Move the desired test item and push the TEST SW to select the test.
- When the tests are finished, move the * mark to EXIT and push the TEST SW.
- DESCRIPTION OF EACH TEST ITEM
- INDIVIDUAL
With the * mark positioned at INDIVIDUAL, pushing the TEST SW or START BUTTON changes the mode from INDIVIDUAL to CONTINUE. Similarly, with the * mark positioned at CONTINUE, pushing the TEST SW or START BUTTON changes the mode from CONTINUE to INDIVIDUAL.
In the CONTINUE MODE, when a test item is finished, the next test item automatically starts, thus making it convenient when performing all the tests continuously.
- MEMORY TEST
This test checks whether the memory IC’s on the game board are correct or not.
The indication of “GOOD” means the IC No. is OK. If a memory IC is incorrect, the IC No. will be indicated as “BAD.”
DIAGNOSTIC VER. 1.00
MEMORY TEST IC. 24 GOOD IC. 26 GOOD IC. 56 GOOD
- INPUT TEST
Checks the operation of each switch, and the V.R. numerical value of the steering handle, accelerator and brake.
DIAGNOSTIC VER. 1.00
INPUT TEST COIN #1 OFF START COIN #2 OFF SERVICE
LOW GEAR ®
HANDLE RIGHT LEFT ACCEL BRAKE
@ Operate each switch. The “ON” indication means that the corresponding SW is OK.
@ When the shift lever is in a low position, “LOW GEAR?” will be indicated and similarly when in a high position, “HIGH GEAR.”
@® The steering test is OK if the numerical value increases to DOH or higher when it is turned to the right and decreases to 30H or lower when it is turned to the left, and becomes 80H+1 when taking your hand off the steering handle.
® The accelerator/brake test is OK if the numerical value increases to COH or higher when it is applied and becomes 20H+1 when it is not applied.
- OUTPUT TEST
Checks the operation of the START LAMP and the OPEN/CLOSE of the coin solenoid which is used to lock in a coin.
DIAGNOSTIC VER. 1.00
OUTPUT TEST
START LAMP ON COIN SOLENOID OPEN
In accordance with the on-screen display, the ON/OFF of the START LAMP and the OPEN/CLOSE of the SOLENOID will take place in one second cycles, and if not, it is considered to be malfunctioning.
() N/A
- SOUND TEST
Only the sound can be manually outputted. Check sound ROM, sound circuit and the operation of the power amplifier.
DIAGNOSTIC VER. 1.00
SOUND TEST 00H®
SELECT BY STEERING
PUSH START BUTTON!
@® Turning the steering handle to the right/left results in increasing/decreasing the numerical value of the sound No. Stop the steering handle at the desired number, push the START button, and that number’s sound will be emitted. For the sound numbers and the description thereof, refer to the following table:
Sound No. | Description OOH - 3FH | Engine sound 61H - 8DH | Effects 90H - 97H | B.G.M. 99H - 9DH | FM effects AOH - C3H | VOICE FFH ALL SOUNDS OFF
- C.R.T. TEST
The monitor adjustment color bar is indicated.
C.R.T. TEST RED
Each color in 8
GREEN gradations
BLUE | @® CR.T. POSITION
L CHECK
Brightness (from white to black)
® Adjust the screen’s position and size by performing the C.R.T. POSITION CHECK.
- DIP SWITCH ASSIGNMENT
Displays the present setting status of DIP SWITCH A & B. For the function of each switch, refer to 24. DIP SWITCHES.
{ DIAGNOSTIC VER. 1.00
DIP SWITCH ASSIGNMENT
| 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | |
| DIPSWA. | OFF | OFF | OFF | OFF | OFF | OFF | OFF | OFF |
| DIPSWB. | OFF | OFF | ON | OFF | OFF | OFF | OFF | OFF |
| A | 1234 | COINSW #1 | 1 COIN | 1 CREDIT | ||||
| A | 5678 | COINSW #2 | 1 COIN | 1 CREDIT | ||||
| B | 12 | CABINET TYPE | MOVING | |||||
| B | 3 | ADVERTISE SOUND | ON | |||||
| B | 4 | EVER OFF | ||||||
| B | 5 | INITIAL CREDIT | 2 CREDIT | |||||
| B | 6 | CONTINUE GAME | YES | |||||
| B | 78 | GAME DIFFICULTY | NORMAL |
- BOOKKEEPING
Displays the records of the number of game plays, game time, etc. Push the START button to proceed to the next screen.
DIAGNOSTIC VER. 1.00 Description of Numbers
BOOKKEEPING @ Number of coins put in COIN
CHUTE 1
| COIN CHUTE #1 | *#*@) | @ Number of coins put in COIN |
| COIN CHUTE #2 | *#@) | CHUTE 2 |
| COIN CREDITS | *#G) | @) Total credits of COIN CHUTE |
SERVICE CREDITS **G) 1&2
| TOTAL CREDITS | ***() | @ Service switch credits |
Total credits of (8) and (@) Total time during which the power was “ON” Number of game plays (including CONTINUE) Number of CONTINUE plays out of @) above Average score ® 1)
@
©) @® High score ® ie)
® TOTAL TIME **H **M **S@)
PUSH START BUTTON
DIAGNOSTIC VER. 1.00
NUMBER OF GAMES ee RED)
RE
CONTINUE Lowest score
| AVE. SCORE | cee | LrC) | ae comer | tee) was |
| TOP SCORE | RHEE RGD) | ae | oe |
LOW SCORE a6) verage game time Longest game time
- * GAMETIME * *
| TOTAL | **H | **M | *S@ |
| AVERAGE | **H | **M | *S@ |
| LONGEST | **H | **M | *S@ |
PUSH START BUTTON
- BACKUP RAM CLEAR
DIAGNOSTIC VER. 1.00 All the BOOKKEEPING contents can be closed. When doing so, BACK UP RAM CLEAR bring the * mark to yes and push the TEST button. When not NO clearing, bring the * mark to NO YES and push the TEST button.
SELECT BY STEERING
PUSH TEST BUTTON
- PARTS LIST
| ITEM | PARTS NUMBER | DESCRIPTION | QTY |
| 1 | 1050-0064 | MAIN SWITCH BRACKET | 1 |
| 2 | 1170-0184 | TERM PLT. (4P) | 1 |
| 3 | 1170-5131 | TERM BLK (5P) | 1 |
| 4 | 1170-5131A | TERMINAL | 5 |
| 5 | 1300-5018 | SPEAKER, 8-OHM 10W | 2 |
| 6 | 1500-0265 | CAP, 24000 UF | 1 |
| 7 | 1500-0265A | CAP MOUNT | 1 |
| 8 | 2000-5090 | MONITOR, 19" RGB | 1 |
| 9 | 2200-0000 | COIN DOOR ASSY | 1 |
| 10 | 2200-5179 | VOL. CNTRL 5K | 1 |
| W | 2600-0011-1 | AXIAL FLOW FAN | 1 |
| 12 | 2600-0011-2 | FAN SCREEN GUARD | 1 |
| 13 | 2800-0418 | STRAIN RELIEF | 1 |
| 14 | 3901-5120 | FLUORESCENT LAMP (1V173) | 1 |
| 15 | 3901-5120-01 | FLUORESCENT FIXTURE (2V810) | 1 |
| 16 | 4001-5089 | POWER SUPPLY 5V @ 15A | 1 |
| 17 | 4201-5891-03 | OWNER'S MANUAL, POWER DRIFT | 1 |
| 18 | 4211-6550 | STICKER, SERVICE SWITCH | 1 |
| 19 | 4211-6592 | STICKER, ON/OFF | 1 |
| 20 | 4211-6671 | STICKER, DANGER | 1 |
| 21 | 4211-6682 | STICKER, SERVICE INSTRUCTIONS | 1 |
| 22 | 4211-6690-01 | STICKER, 120V | 1 |
| 23 | 4211-7224 | STICKER, FUSE 6A, 5A, 3A | 1 |
| 24 | 4231-0091 | MARQUEE PLEX POWER DRIFT | 1 |
| 25 | 4810-0157A | DIODE BRIDGE, 8A | 1 |
| 26 | 5090-0039 | SWITCH, ON/OFF | 1 |
| 27 | 5090-5028 | SWITCH, MOMENTARY | 2 |
| 28 | 5140-0031 | FUSE, 6A | 1 |
| 29 | 5140-0034 | FUSE, 5A (SLO) | 1 |
| 30 | 5140-0036 | FUSE, 3A | 1 |
| 31 | 5140-0045 | FUSE HOLDER, 1P | 1 |
| 32 | 5140-0064 | FUSE HOLDER, 2P | 1 |
| 33 | 5601-5095 | POWER TRANSFORMER, 160P4 | 1 |
| 34 | 6000-0078 | POWER CORD | 1 |
| 35 | 6010-0001 | FUSE COVER | 3 |
| 36 | 6010-0042 | KNOB, 1/4" SHAFT | 1 |
| 37 | 6010-0420 | LINE FILTER, 5A | 1 |
| 38 | MO0-1215Y | POWER CORD BOX | 1 |
| 39 | POWO-1703 | HOLDER BRACKET A (CONTROL PNL) | 1 |
| 40 | POW1-1623 | ASSY ACCEL PEDAL | 1 |
| 41 | POW1-1701-B | DECAL, RIGHT SIDE | 1 |
| 42 | POW1-1701-C | DECAL, LEFT SIDE | 1 |
| 43 | POW1-1702 | SWITCH UNIT BRACKET | 1 |
| 44 | POW1-1706 | HINGE 580 | 1 |
| 45 | POW1-1707 | SUPPORT BRACKET RIGHT | 1 |
| ITEM | PARTS NUMBER | DESCRIPTION | QTy |
| 46 | POW1-1708 | SUPPORT BRACKET LEFT | 1 |
| 47 | POW1-1712 | MONITOR BEZEL | 1 |
| 48 | POW1-1713 | WINDOW GLASS | 1 |
| 49 | TBO-3003 | T.V. MASK 20 | 1 |
| 50 | YZ0-0016 | SHIELD COVER UR | 1 |
| 51 | YZ0-0019 | SHIELD CASE U/R | 1 |
| 52 | YZO-1031-A | BILLBOARD COVER | 1 |
| 53 | YZO0-1031-B | SPEAKER NET | 2 |
| 54 | YZ1-1604 | SUPPORT BRACKET FRONT | 1 |
| 55 | YZ1-1699 | HINGE SUPPORT BRACKET | 1 |
| 56 | 008-0408 | TMP PRF SCR M4X8 | 2 |
| 57 | 008-0416 | TMP PRF SCR TH M4X16 | 8 |
| 58 | 008-0520 | TMP PRF SCR TH M5X20 | 2 |
| 59 | 008-0525 | TMP PRF SCR TH M5X25, | 7 |
| 60 | 008-0545 | TMP PRF SCR M5X45, | 2 |
| 61 | 029-0038 | TMP PRF SCR SCR BH BLK M6X20. | 8 |
| 62 | 029-0152 | TMP PRF SCR TH CROME M5X12 | 3 |
| 63 | 029-0192 | TMP PRF SCR TH CROME M5X20 | 3 |
| 64 | 029-0217 | TMP PRF SCR BH CROME M8X40 | 4 |
| 65 | 069-0087 | FLT WSHR CROME M8 | 4 |
| 66 | 220-5130 | VOL CONT B-5K OHM | 1 |
| 67 | 280-5079 | NYLATCH GROMMET | 16 |
| 68 | 280-5080 | NYLATCH PLUNGER | 16 |
| 69 | 421-6119-91 | STICKER FCC | 1 |
| 70 | 421-6120 | STICKER SEGA USA | 1 |
| 71 | 421-6709 | STICKER SERVICE INSTR ENG | 1 |
| 72 | 421-7329 | ADJUST INSTR SHEET POWER DRIFT | 1 |
| 73 | 600-5726-01 | WIRE HARN EXT VCC. | 1 |
| 74 | 600-5726-02 | WIRE HARN EXT PWR AMP | 1 |
| 75 | 600-5726-04 | WIRE HARN EXT RGB | 1 |
| 76 | 600-5726-08 | WIRE HARN SOUND | 1 |
| 77 | 600-5726-09 | WIRE HARN RGB | 1 |
| 78 | 600-5726-13 | WIRE HARN EXT CAB POW | 1 |
| 79 | 600-5726-14 | WIRE HARN EXT CONTROL | 1 |
| 80 | 600-5726-15 | WIRE HARN VCC POW | 1 |
| 81 | 600-5726-16 | WIRE HARN VO POW | 1 |
| 82 | 834-6697-04 | GAME BD POWER DRIFT | 1 |
| 83 | 839-0035-01 | PWR AMP DC 12V 10W | 1 |
| 84 | 839-0207 | FILTER BD GALAXY FORCE U/R | 1 |
| 85 | POW-20002 | ASS'Y CONT PANEL YZ TYPE | 1 |
| 86 | POW-2210 | EXT SPRING | 1 |
| 87 | POW-2615 | EXT SPRING | 2 |
| 88 | POW-2617 | ASS'Y ACCEL & BRAKE YZ TYPE | 1 |
| 89 | POW-2729 | EXT SPRING | 2 |
| 90 | SGB-1035X | KEY BAG | 1 |
| 91 | YZ-1031 | ASSY, BILL BOARD COVER | 1 |
MS TAMPERPROOF SCREW 029-0152
A ST : (CEES Se a Pp es : eae DESIGN PLATE ‘POWER LRIFT" Lb gly} ‘i? : 4 4231-0091
ASSY BILLBOARD COVER YZ-1031-A
MS TAMPERPROOF SCREW IV.MASK 20 029-0152 TBO-3003
FLUORESCENT LAMP <f 3901-5120 IPR © L_ Ftuonescent rxture 3901-5120-01
- = 8.OHM 10-WATT 1300-5018
FILTER BD POWER DRIFT 839-0207 i. 2 —_— FCC CAGE ASSY & PCB
ASSY ACCEL & BRAKE
POW-2617
P/D U/R POWER SUPPLY ASSY
COIN DOOR 2200-0000
POW-2617
BRAKE PEDAL
ACCEL BAR POW-2608
POWER SUPPLY 5V/SA 4001-5089
FUSE BLOCK ASSY
___ POWER TRANSFORMER, 5601-5095
LINE FILTER 6010-0420
SERIAL # PLATE—————>-
- SCHEMATIC DIAGRAM
Taay| MY NP ie bory
Bat
Thess ILEER Bo GALALY FoKcs 0/8 [=A
229-0207
12-4000 Assy Pe seur
e yea! He Tr