Vigilante
Vigilante (World, Rev E) (Irem, 1988) · Manual · 22 pages · 8 sections · original scan
0084-00.
Ps
DATA EA‘
470 NEEDLES Of 37 USA, INC. RIVE (408) 286-7074 SAN JOSE, CA 95112 TELEPHONE: -PART NUMBER : 780as
- SERVICE & INSTALLATION MANUAL. at
FCC WARNING This equipment generates and uses rao frecuenoy energy and if not instal and used propery isin strict with this instructions accordance manual, may harmful interference to radio communications. This equipment has been tested and found fo comply with the Seuts for a Class A computing device pursuant to Subpart J of Part 1B of the FCC rules, which are desimed to provide reasonable protection against such inter ference when the equipment is operated in a commercial environment. Operation of this a residential is Ikely to cause interference in which case the user, at his own expense, will Be remured fo take whatever mestoren we neces te coe ihe ieee
FBI WARNING
Federal law provides severe civil and criminal reproduction, distribution, or exhibition of copyrighted audio-visual for the unauthorized ted works and video games. The Federal Burcau ef heesficaton ruesteater mores ee, copyright infringemant.
COPYRIGHT NOTICE
Vigilante ™ is Copyright 1987 trem Corporation, licensed and sold exclusively in the United States of America and Canada by Data East USA, ne. All rights reserved.
ENVIRONMENTAL DATA
‘This product is intended for use indoor use only, power requirements are 105-125 volts AC, 50-60 hz, and requires a3 wire grounded outlet.
SERVICE PROCEDURES
Free Techie’ seas ee contact the authorized Date East Distributor i your area. tf you require referral or further technical assistance, you may contact Data East's Customer Service the hours of &00 am to 5:00 pm Pacific Time at (408) 286-7074,
| viciLaNTeT™ | | re |
UPRIGHT MODEL
SERVICE & OPERATION MANUAL,
TABLE OF CONTENTS
GENERAL INFORMATION
Installation and Set-Up s meeersesessecseed
GAME INFORMATION
Game Options.....seecceeseveveene
+ Power-Up Self-Testecsccssseteeseeeseeceeseeeseseereeseed
System Adjustments.......eeeeeeee
« Main Harness Diagram....scceseeeeeucues
REPLACEMENT PARTS LIST... cee eeeeeee cece tere eee eeee eres
PCB SCHEMATIC DIAGRAMS... ...s.eeeeeeee . ween?
© 1987 DATA EAST USA, INC. 470 NEEDLES DRIVE SAN JOSE, CA. 95112 (408) 286-7074
FIRST PRINTING JANUARY 1988
PN: 780-0084-00
GENERAL INFORMATION |
Installation and Set-Up.
- Remove the shipping screws to remove the Rear Access Door using the key supplied. The 2 bolts used to hold the Control Panel to the rear access door during shipment are also used to mount the control panel to the cabinet. The two remaining bolts required can be found threaded into T-nuts in the control panel. Remove the Control Panel from the back door at this time.
- Locate the keys in the package on the front of the cabinet, open the Coin Door. The control panel has two (2) retaining clamps that hold down the hinged section of the panel. Release the clamps at this time. Position the control panel on the front of the cabinet. Raise up the hinged section of the panel and reach inside the cabinet to start threading in the four mounting bolts. Thread in the bolts until they are finger tight. Using a ratchet with a 7/16" socket, tighten the mounting bolts. These may be easier to reach from the rear of the cabinet,
- Plug the 12 pin Molex connector from the control panel into the Main Harness. Close the Control Panel and secure with the clamps.
- Check the Main Harness for loose or unplugged connectors, and check for secure mounting of the monitor, power supply, and game pcb. Stabilize the cabinet using the leg levelers in the floor of the cabinet to prevent the game from rocking.
- The selectable options have been pre-set at the factory for optimum player appeal, however, refer to Chapter 2, Section A} Dip Switch Options in this manual to set the game up for special requirements.
- Remove the power cord from the inside of the cabinet and insert the strain relief plate into the slot at the bottom of the rear access door opening. Plug the AC cord into a grounded 117 VAC outlet and flip the power switch to the ON position. Allow 2 to 3 minutes for the monitor to warm up and check for proper demonstration mode video on the screen. Insert the proper coinage into a coin slot and start a game. Check for proper operation of all joystick controls and switches.
PAGE 1
| 2. GAME INFORMATION
The game options can be changed via 2 banks of dip-switches on the game PCB set. Be certain to remove power to the game when changing settings.
DIP SWITCH 1:
ACTION
NUMBER OF THREE (3): OFF OFF FIGHTERS TWO (2): ON OFF OFF ON ON DIFFICULTY OFF ON DECREASE OF ENERGY COIN MODE OFF
COIN COIN COIN COIN COIN OFF OFF ON OFF OFF ON ON ON iN) |. one
a DOWNER ERR ONE WONE EEE FREE PLAY:
PAGE 2
DIP SWITCH 2:
ACTION
FLIP PICTURE NO:
CABINET TYPE TABLE: OFF UPRIGHT: ON COIN MODE MODE 1: OFF MODE 2: ON SOUND IN DEMO MODE
BUY-IN MODE
DEMO FREEZE MODE : 2P=STOP_1P=CONTINUE YES: NO DEATH MODE
ALWAYS KEEP SWITCH 8 OFF
| B. Power-Up Self Test.
When power ig turned on, the following test is conducted automatically:
- RAM TEST ytests system RAMs for read and write capability.
- ROM TEST jtests system ROMs for valid data.
The RAM test causes various video patterns to appear on the screen for several seconds, and then displays results of RAM and ROM test.
If a RAM fails the test, the screen will display an error message indicating the defective device.
If a ROM fails the test, the screen will display an error message indicating the defective device.
PAGE 3
System Adjustments.
The Volume Control, Coin Counter, and Service Switch are located on the Service Panel. The Service Panel is located inside the Coin Door, mounted on the wall of the cabinet on the left side.
The Coin Counter increments once for every coin dropped through either coin entry slots.
The Volume Control is used to adjust the overall loudness of the game sounds, NOTE: The volume control potentiometer on the Main pcb is preset to mid-range at the factory and should not be adjusted.
The Service Switch can be used to add credits to the game without incrementing the Coin Counter.
The fuses for the AC power line and the 12 volts for the Coin Door lamps are located on the Switch Bracket of the Power Supply assembly as is the ON/OFF switch. The fuse holders are labeled on the Switch Bracket as to the proper fuse ratings.
The +5 vde adjustment level control is on the Power Supply's Switching Regulator is pre-set at the factory. In the event that an adjustment is required, measure the +5 volt level present at the game logic pcb with a Digital Multi-Meter while adjusting the output level of the Switching Regulator. The voltage must measure between +4,90 vde to 5.10 vde at the game logic peb for proper operation.
PAGE 4
PAGE 5 end GND GND GND tRy tH . GND cue
“SV +sv
+rsv +5v +iRav cn-3 Counrer,
~bv 7lav riev Po) BRI Bi cN-4 3 BK FRom ARM o
FROM LOW SIDE (-)
eB] oe sir) CHS
y 2B 4] TO HiGh SIDE (+) “ T] cer exve 7 ELE] cet GREEN
COUNTER 2 COUNTER | SPEAKER (-) SPEAKER @) CRT GREEN CRT RED ERT Syne cRT BWWE
SERVICE
CRT GND
CRT RED CN-& CRT SYNC
CRI GAD SERVICE CN-7
GND
com 2. con |
START 2
START | 2p up 1P uP
2P Down
1P DOWN ap Lert 1P LEFT 2° Right 1P RiGHT 2P PUSH! 1P PUSH) 2P PusH2 VP Push. 2P PUSH 1P PUSHS GND con | L 8) GND cone CNB
CN-IO. KT ony 2 BK Av
LZ] Pi RIGHT +2) Pl LEFT PIUP PL DOWN Pi PUSH | Pl PUSH 2. PI PUSHS GND p2 LEFT Ae P2 uP cK§ P2 DO P2 Pusn) mes PL PUSH
Pr SeuecT 2 Sececr
ND GND CHASSIS GND Wiring Diagram,
. REPLACEMENT PARTS LIsT | Le ll
FINAL ASSEMBLY
CABINET, EMPTY, 1US30, GREY CABINET, EMPTY, 1US25, GREY CONTROL PANEL ASSY., VIGILANTE COIN DOOR, COIN CONTROL 2 SLOT, WIDE COIN DOOR ASSY., COIN CONTROL MONITOR ASSY., UNIVERSAL H/V POWER SUPPLY ASSY., 11AMP PCB SET, VIGILANTE RETAINER, PLEX, MONITOR PLEX, CLEAR, DISPLAY 23.75 X 23.75 UNDERLAY CARD, VIGILANTE LABEL, INSTR. VIGILANTE ‘A’ LABEL, INSTR. VIGILANTE ‘B’ DECAL, SIDE, VIGILANTE PLEX, MARQUEE, VIGILANTE RETAINER, PLEX, MARQUEE, CURVED RETAINER, PLEX, MARQUEE SPEAKER, 6 X 9" OVAL HARNESS, MAIN, JAMMA STD. U/R
CONTROL PANEL
CONTROL PANEL, BARE OVERLAY, CTRL PNL, VIGILANTE PUSHBUTTON, BLACK PUSHBUTTON, YELLOW PUSHBUTTON, BLUE HARNESS, CTRL PNL, 1P/2P, 2S. JOYSTICK, MONROE 4/8 WAY
MISCELLANEOUS PARTS
REGULATOR, 5V @ 11 A& 12V@1A ISOLATION TRANSFORMER NOISE FILTER SWITCH BRACKET W/FUSEHOLDERS HARNESS, DC OUT, 11A CASHBOX, 3 SLOT, METAL CASHBOX BRACKET, LOCKING CASHBOX, PLASTIC FIXTURE, LAMP, DUAL LAMP, 40 WATT, INCANDESCENT LAMP, 14 VDC .19 AMP WEDGE, #161 SERVICE PANEL ASSY. COIN COUNTER, 12 VOLT POT, 50 Q 12.5W, 1/8" SHAFT POT, 100 2 4W 1/4" SHAFT (replaces above) SWITCH, PUSHBUTTON, MOM.
- = FIRST RELEASE VERSION
PAGE 6 365-0012-00% 365-0010-00 510-0127-00 510-0127-00% 510-0004-00 §10-0120-00 510-0002-01 510-0124-00 535-0073-00* 660-0001-01 810-0028-00 406-0088-01 406-0088-02 820-0045-00 830-0036-00 535-0078-00% 535-0008-00 031-0006-00 036-0159-00
535-0083-00 800-0031-00 350-0001-00 350-0001-04 350-0001-06 036-0115-01 450-0014-01
001-0012-00 010-0001-00 150-0004-00 §15-0004-00 036-0031-02 535-0076-00* 535-0077-00% 545-0004-00 170-0002-00 165-0004-01 165-0009-00 515-0029-00 090-0002-00 123-0009-12 123-0008-11 180-0022-00
ONLY
PCB SCHEMATIC DIAGRAMS |
M75-A-B PCB: PAGES 1/5 THRU 5/5
M7S5-B-A PCB: PAGES 1/7 THRU 7/7
PAGE 7
ida BE F-bofe | do bn BEEREE z
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
A rsa nl e.cosas
a a Seas [SR eT ore t zs t es sags «) 1% aot tes
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
TE ars oe ere ee ‘ . v7 ce . :
: dete | bm) econ A
a, wo war MORO.
r Breceegne
LLL Lh H BERCEER TE
eae eee a ee SST SS 3 uf _rouvwoasco oven OUNUN
rT Vo WH7OD-3 ji F Segeeene Beaandng cll
zrrxrerz Beaesn-FH oovox<<cccrxrerrrzzzz ~Rea~-Rgres Re x o f