Frenzy
Frenzy (revision RA1) (Stern Electronics, 1982) · Manual · 29 pages · 14 sections · original scan
- ELECTRONICS, INC. 1725 Diversey Parkway, Chicago, Illinois 60614 (312) 935-4600, Telex 25-4657 Toll Free Service Assistance (800) 621-6424
INTRODUCTION
This game has been STERN final tested and is ready to play, but on all games there are some items that must be checked first after shipment. Making these visual inspections may avoid time consuming service work later. Minor troubles caused by abusive handling in shipment are unavoidable, such as cable connectors that may have been loosened. Check ALL CONNECTORS on the game to make sure they are firmly seated. Examine the exterior of the game cabinet for dents, chips or broken parts. Check all major subassemblies, control panel and T.V. monitor to make sure that they have not loosened up during shipment.
1.2 VISUAL INSPECTION BEFORE PLUGGING IN LINE CORD
aoP,on . Check that the primary wiring of the transformer corresponds to the location voltage (See Figure E). . Check the transformer for any foreign material shorting across wiring lugs. . Check that fuses are firmly seated and making good contact. . Check the T.V. for any foreign material that could cause shorts (VISUAL INSPECTION ONLY). . Check game boards for any foreign material that could cause shorts. Make sure all circuit boards are connected properly.
1.3 ON/OFF POWER INTERLOCK SWITCHES
. The on/off power switch is located on the top right side 12” from the front. . There are two interlock main power switches, one by the front door (See Figure A) and one on the back access panel (See Figure B). . Interlock switches interrupt all power from game except service outlet and flourescent lights for Marquee. Interlock switches can be locked in “ON” position by pulling stem out when servicing game. :
1.4 GENERAL INFORMATION
. On the front door there is a bookkeeping switch (See Figure A). Depressing this switch will step through bookkeeping functions one at a time for each time switch is pressed. Pressing fire button will clear whatever bookkeeping function you are in. (See Page 14 for bookkeeping function).
. There are two coin chutes on the front door. They can be adjusted to work separately. (See Page 13). . Game adjustment switches are located on ZPU board. (See Pages 10, 12 & 13 for adjustments and location). . Volume control for electronic sound is located inside the front door on right side. (See Figure B). . Power supply has an adjustment for the +5 VDC regulator, this MUST BE SET BETWEEN +5.0 VDC and +5.25 VDC as measured at TP4, VSU-1000. (See Figure D for test points on power supply and adjustment pot).
FIGURE -A
FRENZY FRONT CABINET
SPEAKER
CONTROL PANEL
SEE FIGURE - C FOR SLIDING DRAWER DETAIL
INTERLOCK SWITCH
LOCKING ASS'Y. FOR SLIDING DRAWER DOOR BOOKKEEPING SWITCH
FIGURE -B
FRENZY
REAR CABINET
ON/OFF SWITCH SPEAKER
INTERLOCK SWITCH
FLUORESCENT 4 FUSE ASS'Y.
CONVENIENCE OUTLET
VOLUME CONTROL
SLIDING DRAWER FIGURE - C
ADJUSTMENTS & FUSES
TO REMOVE SLIDING DRAWER CABINET
- REMOVE ONE LOCKING SCREW FROM BACKSIDE THAT LOCKS SLIDE IN PLACE
- REMOVE SLIDE RETAINER BRACKET THAT IS HELD ON WITH TWO SCREWS: REMEMBER TO REPLACE THESE ITEMS IF GAME IS TO BE MOVED SA/ NORMAL OPERATION JUMPER MUST BE IN NORMAL POSITION FOR GAME TO PLAY/— RESET BUTTON FREE GAME BUTTON SEE PAGE 10 SEE FIG. -D
DIP SW. BANK F2-c— rose DIP SW. BANK F3- c—— P (3 ASB)
- DIP SW. BANK F4- : DIP SW. BANK F5-C—3
DIP SW. BANK F6- C— VARISTOR
oO 130V FOR 115VAC LINE 250V FOR ZPU-1001 220 VAC LINE
120V/240V JUMPER BOARD BSC-1000
POWER AND sB-1000 [] ISOLATION XFMR.
DIP SWITCHES SEE PG. 10 SEE PAGE 8
NOTE:
+5 V ADJUSTMENT MUST BE
TP-1 +5V TP-2 +5 VDC ADJUST. —5VDC BETWEEN +5.00 & +5.25 VDC
(SEE NOTE) (MEASURED AT TP4, VSG-1000)
HEATSINK tov BRIDGE
- [ es | et 2 ra 3_AMP 3/4 AMP 5 AMP ‘ASY 'A,SSV
OO00l-Sd
O60 Bloons
Ag SawnidwsnNwn QNY GINDINaa +19V #12V —5y REGULATORS FIGURE D
POWER
TP-4 TP-5 TP-3 +12 VDC GRD +15 VDC
FIGURE - E
TRANSFORMER STERN 16D-13
13124 3 21
JUMPER
115 VAC 220VAC 130V VARISTOR 250V VARISTOR FOR 115 VAC LINE FOR 220 VAC LINE
J-2 10-PIN
u-4 10-PIN = aa CODBNONSOND— NFWOOSONODTSAWNH=
aaa N-OCOBNONSWOND—
OCOOnNONE2WN= General III. General Il! Volume Control High
Bookkeeping Volume Control Low Coin Door Common Slam Coin 1 Coin 2 Coin 3 Spare
Spare Spare Fire Joystick Left Joystick Right
Joystick Up Joystick Down +5 to PRU Control Pane! Commo:
Two Player Start
One Player Start Fire Spare Ground Joystick Left Joystick Right Joystick Up Joystick Down Spare +5 to PRU Control Panel Common
Speaker High
Speaker Low Video SYNC Red Green Blue Spare Video Ground Video Ground J-5 12-PIN
J-6 10-PIN
Player 2 (Cocktail version only)
12-PIN
J-8 10-PIN To Monitor
OPERATION
Insert coin for credit. Start game by pressing START button. Object of game is to have Humanoid Intruder shoot as many Robots as possible and escape from room. Humanoid Intruder is controlled by player with control stick. (Eight directions possible). Note: Humanoid Intruder stops moving when shot is fired. Shot is fired in direction Control Stick points to. Bonus Score for each room full of destroyed Robots (even if Robots destroy each other), EVIL OTTO comes out from position Humanoid Intruder started, can be destroyed will go thru walls, and follows Humanoid Intruder with its object to destroy the Humanoid Intruder.
F2 | F2 LOC. F2 617 BANK
LOC. F3 BANK
F4| F4 LOC. F4 6|7 BANK
FS LOC. F5 7 BANK
F6 F6 F6 LOC. F6 3 5 7 BANK
sw.2 FREE GAME SWITCH
(BOOKKEEPING)
ADDITIONAL SWITCHES
| ELECTRONIC BOARDS | SWITCH NO. | PINS | USAGE |
| Bsc | 1 | 1-8 | Breaks WAIT line for SIGNATURE |
ANALYSIS (S.A) MUST BE Closed for game operation
| 2 | 2-7 | Adjusts color outputs for the variations In |
| 3 | 3-6 | monitor input circuitry |
| 4 | 4-5 | SHOULD BE: |
QPEN FOR WELLS-GARDNER CLOSED FOR ELECTROHOME
| VFB 100 | 1 | 1-8 | NOT USED |
| 2 | 2-7 | Breaks NMI line for S.A. |
MUST BE Closed for game operation
| 3 | 3-6 | Breaks iNT tine for S.A. |
MUST BE Closed for game operation
| 4 | 4-5 | Breaks WAIT line for S.A. |
MUST BE Closed for game operation
| $B 1000 | 1 | 1-8 | Breaks WAIT tine for S.A. |
| 2 | 2-7 | NOT USED | |
| 3 | 3-6 | NOT USED | |
| 4 | 4-5 | NOT USED |
JUMPER OPTIONS
SB 1000: JUMPER W1 MUST BE CONNECTED (W2 OPEN)
VSU 1000: JUMPER W3 MUST BE CONNECTED (W4 OPEN)
ZPU-1001: J8 PINS 2-3 MUST BE CONNECTED TOGETHER
CHIP 6513 H 6513L 6514 CHIP LOCATION 1€ MAY BE POPULATED BY ANY ONE OF 3 DIFFERENT CHIPS
STERN PART NO. 56A-6-S004 56A-6-S003 56A-6-S002 CONNECT JUMPER WSs Ww6 wit
FREE GAME SWITCH (SW. # 2)
Switch #2 (printed on board “Bookkeeping Clear”), if pressed when HIGH SCORE TO DATE IS DIS- PLAYED will provide one game without being added on any coin bookkeeping.
MONITOR DIP SWITCH AND GAME SWITCH DISPLAY TEST
Set dip switch 3 on the ZPU board (location F2, See fig. D) to “ON” position, then press the RESET button (SW. #1, located at F1 on the ZPU board). The monitor will display the OFF (0 on the monitor) ON (G on the monitor) status of the 40 “ZPU DIP SWITCHES” on the upper chart and the open (0 on the monitor), closed (Q on the monitor) status on all game switches on the lower “VFB SWITCHES” chart. SEE BELOW FOR ZPU AND VFB SWITCH ASSIGNMENTS. (SEE PAGE 13 FOR DIP SW. DESCRIPTION) (NOTE: GAME SWITCHES CAN BE TESTED BY CLOSING AND SEEING IF CLOSED DISPLAY SHOWS UP. ON MONITOR CHART). To return to normal operation set dip switch 9 to OFF position and press RESET (SW. #1) button on the ZPU board.
| H | : | 3 itch | M | DIP |
| Normal; | Normall | wite! | lonitor | |
| OFF | | OFF | | Test | Test | BANK #1 |
z (On tor Loc, F2
| U | 10 | 1 | 12 |
| ° | EXTRA MAN ADJUSTMENTS | Pees EPG. 13 | Een #2 |
t SEE PG. 13 " LOC. F3
| s | 7 | 18 | 19 | 20 | 21 | 22 | 23 | 24 |
DIP
| sf | ~ COIN ROUTINE COIN SW. 2 | BANK #3 |
| t | SEE PG. 13 | Loc, F4 |
c
| H | 25 | 26 | 27 | 28 | 29 | 30 | 31 | 32 |
DIP s COIN ROUTINE COIN SW. 1 BANK #4
| T | SEE PG. 13 | LOC. F5 |
A
| tT | [a3 | 34 | 35 | 36 | 37 | 38 | 39 | 40 |
3 SET VALUE FOR DIP
CREDIT BUTTON BANK #5
| | | SEE PG. 13 | LOC. F6 |
VEB SWITCHES (SHOWS SETTINGS)
ON WHEN | ON WHEN | ON WHEN | ON WHEN | ON WHEN vee | JOYSTICK | JOYSTICK | JOYSTICK | JOYSTICK | FIRE . ATLEFT | AT RIGHT | UP
s
| w_ | | ON WHEN | ON IF |
f START 1 7 | PLAYER ¢ [ISON H STATUS *
O = SWITCH OFF (OPEN) OG = SWITCH ON (CLOSED)
- = NOT USED
ZPU DIP SWITCH
| SWITCH NO. | LOCATION | FUNCTION |
SW. #100000... cece FQ occ ccc ce eee ee ees Signature analysis mode (service only)
| SW. #2 | F2 | Signature analysis mode (service only) |
| SW. #3 | F2 | Switch test |
SW. #4....... 0c FO cece cece eee teens Monitor test
| SW. #5 | F2 | N/U |
| Sw. #6 | F2 | N/U |
F2 N/U FQ cee cecneeee eee eees N/U FS eee eee F3 F3 Extra man adjustments (See page 13) F3 F3 be hew sent eamnane eben NvU N/U F3
Coin routine coin switch #1 (See page 13)
Set value for credit button (See page 13)
DIP SWITCH. ADJUSTMENTS
CREDIT/COIN ADJUSTMENTS: The Frenzy Credit System is a programmable system using the Binary number system to set a value to both Coin Chutes and the Credit Button.
This Coin-to-Credit system will allow many different pricing schemes. Every coin is counted as a Dip Setable number of clicks. The Credit Button is also counted as a Dip Setable number of clicks. When enough clicks to make a credit are on hand, a credit is given and the clicks are subtracted from the total on hand when the Credit Button is pushed. There can be clicks left over in any amount less than the number needed for a credit. The click value for the coins is set to zero whenever the player(s) start a game. Dip Bank #3 on the Z.P.U. Board sets the value for Coin Switch 2. Dip Bank #4 on the Z.P.U. Board sets the value for Coin Switch 1. Dip Bank #5 on the Z.P.U. Board sets the value for the Credit Button.
Dip Switch Number 12 3 4 5 6 7 8 ON Binary Value 1 2 4 8 #16 32 64 128 OFF
FOR EXAMPLE: Dip 3 12xxxxxx = Binary Value 3 Dip 4 12xxxxxx = Binary Value 3 Dip 5 x2xxxxxx = Binary Value 2 GIVES: Credit/Coin Ratio of; 1/1,3/2. Dropping the first Coin gives you three clicks, if you push the Credit Button now (the Credit Button value is set at two clicks) you will get one credit and have one click left over. If you now drop a second coin, you will get three more clicks plus the one you had left over, giving a new total of four clicks, for two credits.
DIP BANK 1 DIP BANK 2 xxxx No ExtraMan x23x 6000 xx34 12,000
| 1 | SA. | 1 | 1xxx 1000 | 123x 7000 | 1x34 13,000 |
| 2 | S.A. MODIFIER | 2 | EXTRA MAN | pet con | xxx4 8000 | x234 14,000 |
| SWITCH TEST | 3 ( LEVEL | xX | 1xx4 9000 | 1234 15,000 | |
| 3 | xx3x 4000 | x2x4 10,000 | |||
| 4 | MONITOR TEST | 4 | 1x3x 5000 | 12x4 11,000 | |
| 5 | N/U | 5 | N/U | ||
| 6 | N/U | 6 | N/U | ||
| 7 | N/U | 7 | 0,0 = English | ||
| 8 | N/U | 8 } LANGUAGE | 0,1 = French |
ad 1,0 = German 1,1 = Spanish
BOOKKEEPING
Inside the coin door Is the BMDS (Bookkeeping Monitor Display Switch) - (See Fig. A). Depressing this switch one time initiates this function. The first bookkeeping function to appear on the monitor is number of credits (*Green). To delete from memory press either Fire Button. Depressing the BMDS one more time will advance the bookkeeping up (*Blue), and the second bookkeeping function (total coins thru coin chute #1) will be displayed on the botton (*Green). To delete from memory press either Fire Button. The previous bookkeeping functions will remain on the screen (*Blue) and the new function will appear on the botton (*Green). Bottom function can be deleted from memory. Following is a complete list of bookeeping functions. ‘ “Color of display if color monitor is used.
FUNCTION DESCRIPTION DIGIT DISPLAY
| 1) | Credits | Total Credits | 00 |
| 2) | Chute #1 (Left) | Total Coins | 00000000 |
| 8) | Chute #2 (Center) | Total Coins | 0000000 |
| 4) | Chute #3 (Right) | Total Coins | 00000000 |
| 5) | Plays | Total Number of Plays | 000000 |
| 6) | Score | Accummulated Score | 000000000000 |
| 7) | Time Played | Total Amount of Time |
Played (in seconds) 000000000000
| 8) | High Score | High Score To Date | 000000 |
COIN INSTRUCTION TRANSLATION (SWS. #15 & 16)
Will say in different language correct coinage
SW.-#15 SW.-#16
| ENGLISH | OFF | OFF |
| FRENCH | OFF | ON |
| GERMAN | ON | OFF |
| SPANISH | ON | ON |
TROUBLE SHOOTING BY SELF-TESTS
PERTINENT INFORMATION
- The following tests occur each time the RESET button is momentarily pressed or when power is removed and re-applied.
- The self-test indicating LED is on the ZPU-1001 board (CR45) and each indicating flash is accompanied by a tone from the sound system.
- The LED stops flashing at the malfunction provided all PC boards are connected in the system.
FIRST SELF-TEST
The first of 8 LED flashes occur accompanied by a tone from the speakers. This first test analyzes the ROM circuits on the ZPU board.
ANALYSIS OF FIRST TEST WHEN LED STAYS ON
Continuous illumination of the LED indicates problems in one or more of the following areas:
- The POWER-ON RESET circuit. Check NAND gate 7G, inverter 8G and associated circuits.
- Loss of clock signal. Check oscillator transistor Q12, flip flop divider 8A and other associated components.
- Microprocessor (Z-80) is defective (Chip 7B).
- Defective Address Bus (shorted or open) or contro! buffers (chips 6B and 7D, type LS244).
- Defective ROM chip(s).
- Defective 1/O Decode Circuits. Check chips 5A, 4A, 6A, 7G and decoder 7E.
- Defective LED latch. Check chips 7G, 3A, and 8G.
Analysis of First Test when LED Flashes Once and stays OFF. This sympton indicates the problem is in one or more of the following areas.
- Defective PROM circuitry. Check all PROM chips since the malfunction may be in any one chip.
- Defective Address Decode Circuit. Check chips 6E, 4A, 5A, 6A and 8G.
SECOND SELF-TEST The second of 8 LED flashes should occur accompanied by a tone from the speaker. This test analyzes the “scratch pad” area of the RAM on the ZPU-1001 board. For the following diagnostics, the LED must flash twice and extinguish.
ANALYSIS OF SECOND TEST
- Check transistor Q2 and associated components/circuits.
- Defect in gating chips 2A, 3A and 6A.
- Check that the jumper used for chip 1E (W5, W6 or W11) Is correct for the particular chip part number. See page 10 for jumper options.
THIRD SELF-TEST The third of 8 LED flashes should occur accompanied by a tone from the speaker. This test analyzes the RAM (screen RAM) located on the VFB-1000 board. For the following diagnostics, the LED must flash three times and extinguish.
- The CRT will display a RAM chip location map which will indicate a defective chip. Mentally rotate the map 90 degrees counterclockwise to properly orient the map with the lower right hand portion of the VFB-1000 board. If the defect is not located, use the following steps: . Check the +12V and -5V voltages, specifically to the VFB-1000 board. . Check RAM address Multiplexers 6F, 6G, 6H and 6E. . Check the RAS* and CAS* circuits: chips 4E, 7E, 1G, 5G and 5F. . Check the “RAM write” circuits: chips 5F and 5E. . Check the Address/Arbitration circuits, chips 5G, 5F, 7E, 3F, 1F and 2D. Check that switch 2B (contacts 4 & 5) is set to the ON position. . Check the “magic” enable circuits of chips 7B and 5C. . Check the “write” data path of chips 7A, 8A, 10A, 11A, 12C and 10C.
- Check the “Read” data path of chips 10D, 11D and 6D.
- Checks all Bus connectors, especially J1 and J2 on both the VFB-1000 and BSC-1000 boards. @Oaaron
on
*Denotes negative true logic
FOURTH SELF-TEST The fourth flash plus a tone test the RAM circuits on the BSC-1000 color board. IF the LED stops on the fourth flash, perform the following listed tests:
- Check RAM chips 3B, 2B, 1B, and 2A.
- Check the Address Multiplexer chips 4C, 4B and 4A.
- Check that DIP Switch 2F (pins 4 & 8) is set to the ON position.
FIFTH SELF-TEST The fifth flash plus tone test the Shifter/Flopper circuits on the VFB-1000 board. If the LED stops on the fifth flash, perform the following tests.
- Check Shifter/Flopper chips TA, 8A, 9A, 10A, 11A, 8B, 9B, 10B, 118.
- Check ENABLE gates 7B and 5C.
- Check control latch 6C.
- Check “OLD DATA” latch 7C.
- Check Port Decoder 4D.
SIXTH SELF-TEST The sixth flash plus a tone tests the Arithmetic and Logic Unit (ALU) and the intercept circuits on the VFB-1000 board.
- Check ALU chips 12C, 10C.
- Check ENABLE gate 5C.
- Check the Intercept gates 12A, 12B.
- Check Flip-Flop 68 and associated gates of 5G and 1H.
SEVENTH SELF-TEST The seventh flash plus a tone tests the Interrupt and Non Maskable Interrupt (NMI) circuit portions which are on both the ZPU-1001 and VFB-1000 boards. When the LED stops at the seventh flash, perform the following tests:
- Check that Dip Switch 2B (pins 3-6 and 2-7) is set to on.
- Z-80 microprocessor.
- Interrupt generating circuitry 1G, 3D, 2D.
- Time Gating circuity 1E, 2F, and 2E.
- NMI ENABLE Latch 1D.
- NMI generating circuitry 2E, 3E & 2D.
EIGHT SELF-TEST If the LED indicator and associated tone have occured eight times, the malfunction is either in a circuit that is not within the testing capabilities of this self-test program or the problem Is unique such as an intermittent condition that changes with physical movements or temperature. After eight flashes have been obtained, try the game to see if the problem has been removed by the check-out action. If the game operates propertly, it is advisable to attempt to locate the former tia by checking all connectors for tightness. Also lightly tap various areas while viewing the RT. If eight flashes have occurred and the game is still inoperable, the following information outlines the circuits that are not part of the self-test routine and must be verified by other test methods:
- Check the settings of all DIP switches on the ZPU-1001 and VFB-1000 boards by setting switch $9 (on ZPU-1001) to ON and then pressing the RESET* button (on ZPU-1001). The CRT will display the ON/OFF conditions of all switches which must then be checked against the Installation and Operating manual data.
- Visual analysis of the CRT pattern (when it is available) can provide many clues to circuit operation as described in the following paragraphs. Total loss of the CRT display usually indicates problems in the monitor itself.
- Malfunctions in the horizontal or vertical address counting circuitry, or SYNC generator circuits will cause “bad” video to be displayed. Vertical or horizontal stripes should give an indication of where the error is. A rolling or flipping picture is an indication of SYNC problems, either in the monitor or on the VFB-1000 board SYNC circuits.
- Color splotches are an indication of a malfunction in the color gating circuitry, or a monitor problem. Check BSC-1000 board chips 2C, 1C, 2D, 3D, 3E and associated switches and resistors.
SOUND SYSTEM PROBLEMS
- NO SOUND; Check amplifier 8C on the SB-1000 board. Check VAUDIO (+15V MAX).
- Voice is normal but there are no sound effects: Check the 6840 chip on the VSU-1000 board. On this board check that Dip Switch 10B (pin 1-8) is in the ON condition. Check the addressing and timing circuitry chips 6A, 8A, 9B, 9A, 9C, 10C, 8A and 10B. Any other malfunction will result in either the loss of a specific sound or, a change in a sound and car: thus be identified as a related circuit.
- Sound effects are normal but there is no voice: Check VSU-1000 chips: CRC ROM chip 3C, PROMs IC, 2C, clock generator 5A, 6A, decode & control logic 1A, 2A, 3A, 4A, 2B, 5B, 6B, 6C. Also check the -10V supply (on the board). Distorted Noise: check PROM 1C, 2C, CRC ROM chip 3C, filter & amplifier 5C.
RF INTERFERENCE PROBLEMS
ES ES TE SS POF CS YE ° ELECTRONICS, INC. 1725 Diversey Parkway, Chicago, Illinois 60614 (312) 935-4600, Telex 25-4657 Toll Free Service Assistance (800) 621-6424
REVISIONS
SYM DESCRIPTION
A ISSUED E.I. 80922. 2N6226
ca n
CRI KBPC6005 BRIDGE <<
i. A /\ No 8 Jl ¢ 2 15,000 MFD + SV. REG. 16 V. (fra) } Sy ts REG
Fe
- ——_|—_~-|_J
RZ 2A SB R7 |
y ¥ CRS IN5391 | spd °} i
FOR I2DV LINE, CONNECT I TCS AND 2 T0 4 SN +12V_UNREG [ ; LL +12V REG FOR 24@V LINE, CONNECT 2 703, | AND 4 SHOLLD GO TO LINE. tev REG
Cc? 6 Sek sgl | T @. af C
L NOTES - 3,8,9,10 $-826-9b¢
i r-4 GND [) ~> SHOULDER WASHER REQUIRED ON MOUNTING STUD 2> GENERAL INSTRU-AENTS 6.3 VRMS TO GEN. ILL.
cRe J he o 2 IN4004 1A SB 75.0. ,2W
lz le
l |"
TO MONITOR c5 a: 103 vaMS @ [et t>>—e L
POWER TRANSFORMtR 16D-26-1
ELECTRONICS, INC. 1725 owerse Parkway, Cheap, ino 60614 "Telex 254657
SCHEMATIC ,POWER SUPPLY
P.C. BOARD
34C -978-S
HEAT Sik @ REGULATOR, vy SHOW FOR REFEREE chly IE NOT LOCATED ONP.C. BOARD [ HSA-1000 | jo
| | sasea i
I I
1_START.
3 START
,~—4 _ 5
TRANS FOMEF EF EREMLE CFL, NO™ PRO BIAEL REVISIONS
DESCRIPTION
ISSUED, EI. 00285
+5 VDC REG
45 VDC REG
45 Ve RES
-5V REG A\2V REG
NAV REE
~5V RES
@up
-——> 10 and e—— awn \2 +9f,,(Audtor key-——L5 13 Key
\ JNREG Wyte), ONRE S77 UNRE: is Zep 4
NRG 45 ve. Ree, ¥5VDC F
+5VDC FE:
-5V fee
+lav Re
+2V FES
~5v REG
4 @ND
1o GND
1 @vo
12+ 85, (AUdTO) 13 KEY
ee eS 15-4, For WN RES
1725 DIVERSEY PARKWAY. CHICAGO, ILLINOIS 60614 (9121 895-400, TELEX 25.4057
TOLL FREE SERVICE ASSISTANCE (00) 621.6426
- ILLINOIS ONLY (0) 872: FRENZY POWER SUPPLY BOARD
12D-668-S
& os os Wn & ot
| R28 s HH HH R29 R2
Wn. Ro = RI2 ion. wey Wn R40 RB oa’ Lobe Ra = RIA
eS mae | Oa Lege tox R43 Rig R44 = RIT lon. Sie Wa.
R50
12D-788-S CAPACITOR & RESISTOR BOARD on”, RSS RAG Ton. ta 4 Wa
FRENZY RESISTOR, ILLINOIS ONLY (800) 721948 (312) 895-4000, TeLex 25-4657
TOLL FREE SERVICE ASSISTANCE (90) 62.6428
1725 DIVERSEY PARKWAY. CHICAGO, ILLINOIS 6614 = Ss @ TS$-88l-aell_ a o sym A DESCRIPTION ISSUED E.I. 99389 REVISIONS Joare Joare | Dare |
REVISIONS: orm DESCRIPTION eae A | ISSUED EI 60324 eet 3 5
c DRAFTING ERROR E.I. 00390 ‘ADDED MISSING INFORMATION E.T, 00441 Bee
ill
ES shit
a SELLE LL oe SPOS! CoP epete @8 eqbeeeo [ rari Zan $
ital EE BeelRs RE
a i PEL Se EEE se EEPE
aaa 88 abe =
xfue
R| on zeezebeee) 4 SPARE GATES
ay Pr} ried &: ||||||b , é
(SCREEN RAM)
S367 Ls273 Ls244 Stenarur BNaLYSIS. La Lsi6i wears wile : 5 7 i Cel Ty oe Lsi66 Lsi61 ANALYSIS: LSI55 Lsi53 LsI09 Ls75 us74 Ls32 Ls27 Lsi4 LsIo Lsos Lso4 Lso2 L800 7401 fer-6 rune a} fy] ]y] as] | a] |5 | | co | 0 | 00 | 0
Cc. TYPE 1725 DIVERSE PARKWAY. CHICAGO, ILLINOIS 60614 312) 9354600, TELEX 254657
TOLL FREE SERVICE ASSISTANCE (@00) 621.5424
ILLINOIS ONLY (800) 572.948 FRENZY VIDEO FRAME BUFFER BOARD
12D-660-S
HL INTENS SPARE GATES REVISIONS, DESCRIPTION TO COMPLETE PRODUCTION SCHEMATIC E.T. 00433
CEs ts 7
| GED—GED rey | ‘sy | $V a |
an +L ce CIB, CII,Cl2,C13,C14,C15, 22uf
| ‘srr | lev | = |
Olut ©) a SND =D
(SEE NOTE)
| % | RI | RIG | 5 |
Took W/W 9 WA — +5 3600 2700 {> ) 12 BRESo2 yg
| isio | ‘7406 | 1500 |
("7777 ZZ
| L | Fe Fp | 20 | \o3 | 2 | RED, | les. |
| Lt | ise7 | Ls04 | nr | (sao | 7406 | . |
NOTES: ns
| + | (See NOTE) | |. DIP SWITCHES F2-2,F2-3, & F2—4 | o | |
| tc | 5 | R20 | Rig | SHOULD BE OPEN WHEN USING WELLS |) |
+5V GARDNER MONITOR, CLOSED FOR 4
| Ls00) | 3600 | 2700 | ELECTROHOME MONITOR. | o |
| 5 | 2. FOR NORMAL OPERATION SWITCH | io |
RIS F2-1 SHOULD BE CLOSED.
| | | 5, | 5 | 4] 3p | 65] | 6 | 4 | a |
tT t El ic 7502
| 4 | ames | (soo | Lsio | 7406 |
tsoo
| GeD— | Gm st | 12 |
:) GREEN
| (ero | TED AIS. | 13] 20 | pot |
r| 6
| fore | CED AS | Ls0o | |||
| GeD—GEDES | Ff Ie | (SEE NOTE) | us273 | 20 | 1 | ||
| Ges | TT | Fes | RIT, | uses7 | 16 | 8 | |
| (SEE NOTE) | 2p | \>8__MEMRD, | 6 | R2I | asv |
| G89} | Lado | Ls24s | 20 | 10 |
yy US74 us7a | 14 | 7
| Ges | a5 tl | user | a | 7 |, |
LsIo 4 | 7 GE—GED
| Gat | Fea SMO. | WiS>o! | Lso4 | 14 | 7 |
Lso4 tsoo | 14 | 7 ev vas | 14 | 7
| 5 | 7401 | 4|7ke | |
| ieee | 214 | Is | 9 |
| | 20 | ps! | 10 | BLUE |
SERV +5V | GND
| GE | H=18 | *. | 7406 | t.c. TYPE -———+-__—4 | |
| E | i | LSOO | KEY G3=3) | ~~ | PIN NO. |
1725 DIVERSEY PARKWAY. CHICAGO, ILLINOIS 60614 (312) 995-4600, TELEX 25-4657 (eS eevee] TOLL FREE SERVICE ASSISTANCE (80) 621-6424 ([SSHeeewne) uiwors oncy coos 572.1068, FRENZY BUFFER SYSTEM COLOR BOARD
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
5 MHZ
GDH +5V 2.5Mnz +8v +5V CR35
| +N | 7 | R33 | iNaia8 | R36 | R29 |
Ds “Pt seth x
| or | : | cro: |
Tea 2,03). THRU C1
| BA | [ | cig THRU C27 | mice | +5V xe |
| 6 | cRa6 | Olu | ||
| tk | om | F ingias | NMOS RAM |
re y" 7474 ost 028. R44 4701 25V 47ptT +5v POWER _ON NESET DATA _BUS, tev
| MicRO — PROCESSOR | leo | rs | ||||
| 1 14 Sag | 2 | Sar ve 7 | Ae ne? | a | ||
| 15 | 31 | Wai | ari | Al | = | |
| Toe | Aan | ALNMO 9 0 | bah | |||
| oe aa | las ays | 8 | Pipers) | |||
| os a3 | ‘Bese, evetZ | a3 | 7 | rien | 7 | |
| oa nap 34 | Thong ovat | Aa | 6 | in | 6la2 oa {tt_F]N_§] | |
| 15} oq3TYP | AS. | 5 ad Me 3 | 5],.ROM [ig | |||
| os asl | 4 Pe ie) bai 6 | AG | as) 03 L | JAB 2 08 | ||
| ve ao 3& | ia2 (8) v2] | 4 | 14 | Fiver | 4 | |
| 2 tT | 18 | AT | a4 be | |||
| o7 arp Sz | 1G_2t | 3 | 15 | as os LS | 5. | |
| ir) | 1g LS244 | 2] 10 Tg | 30 Li | 2 | ||
| 760 | s | op gus | t 2146 ' | as °? os iS | ||
| +5v. | BUFFER | i | 17 | i | i | Hi |
| 20 | AT 07 | jar? OF a5} | ||||
| fr sof 38 | Sis vee afl4 | AB | 23), | 23/,6 | 23], | |
| frm a} 39 | 4x2 waft | Ag | 22). 2732 | 22] 2782 | 22], | |
| BUSREC, gy] 40. | rary | vif 8 AIBN, 1g | [920 | 2] fe]sf2o | ||
| a an | Weng eva | ai | = | |||
| 3 | z | a3 | . | |||
| eae TYP eve | mi St | ‘ | ||||
| 84g (8) salt | aN 45y—=d % | +5v-26 & |
A ear Faq es AISK] au SPARE GATES TTY Sig | L244 Bol
| = | ‘ADD Bus| | 1h | . |
| = | 4 BUFFER | ‘SEE MANUAL FOR W3,W4, 8 WS | mage |
| ALL | 18 5 oa} | ‘OPTIONS | |
| Al2 | u | f2 |
or QADOUN AIS i Pu Bie oe pe GE ps}4 apo 1AM 13 tas oof 5 reo N als. 14 beg osp& 32x8 ve PROM 6
| (Sqr or}2 — | ; | Yea | |||
| Le Ts | 456 | Ts32 | |||
| ~ Casy Li | see | Ls06 | RD | 304 | 4 |
| 1 Rolb | Bh 2 | “1804 | 1 pt soe | ||
| 1304 | 4/44 oS —4 | = | f= 34 |
SS rey) +5v WAI ree +5V
| or | won | ides | ||
| aan | ts32 | 00 7 oR eye) 3D | ||
| lor_i6 fe | 4 | or | ||
| 1 | NTA | 2 Bot | oz 15],, | 44,5 | 02 |
| 7408 | oS 13log | gel | 203 |
Ey
| BeaDeE | | | T | +5V | 4 18) 5) e res | D4. | |
| IN/OUT | JAS | | REO | 4 | YO5 1H 5 | ref 2 | Os |
| | | 10K | Mabiad | \06_14}55, | ast | ||
| 8 | \O7_12 | wale | D7 | |||
| G | nee | 96 | Yon” | N2N4403 BOOKKEEPING | 27 cu & | | |
| ah | 24403 | RESET | Lys |
Ts0q Ls245
| i | 25 | C38 Ig asi | ne | = | |
| SB | Ie Pav | , | vf | +5V | |
| AG | : | 15) wie | a 15} swag [2-S2] | wa ry2fi6 DU | 1K.a R24 |
14 eae ave
| swe | ca swer 2 $3 | TREN oe | 928 lake | nce | ney | ||||||
| Id | swee 4-4 | 13 ge 3 | 038K n R26 | Ke | ad | ||||||
| mie | cr 12| swoo/5-S5 | aaa” eva} O41 0,23 Yaka, | a | ae | al | ||||||
| 3, | cx ui} $f,|6 sé | tae vad DST | 5 | Wea R28 | |||||||
| swes | Rp IO ys: SZ | eee va | Noe | eh — i | |||||||
| 9} swa2 ff | 2al avif2 | J 07. | Wk.o R27 | ||||||||
| “see | naias | nai | ae | = | (Sbitces) | (SPeaces) | ] | us2eq | We ae | bt | A |
| (ot aces) | (B PLACES) | (8 PLACES) | es | It | 2N4403, | “ore |
odes Sdeebattoiagsess GAME SETTING SWITCHES BQEESE ECHECE B05 SOR ESR ESE ii oe ae t 169-0
| 4 | TR4 | 30 |
Als) "
BOS TOLL PREE SERVICE ASSISTANCE (20) 62-0424 p a TCLINOIS ONLY (00) 5724048 i f f FRENZY e ZPU-1001 UNIT \s) 3) 34C-907-S
Tp2 Tea
TPS
TPB TEST POINT FUNCTION LOCATION
+5V GND. TP5 —_ BUSACK 6c WR TPT cpu 8B ZPU- 1001 + UREG 5V (9V)
ures +5vpo7
[TEST POINT FUNCTION LOCATION J3-4 TPL ono Tee ENABLE Tes VaTEN Tpa——vaUDIO TPS. +5V
SB-1000
Tel -10v Tez cLock Tes ‘GND. Tra 45V TEST POINT FUNCTION LOCATION J3-10
3-3 I3=12, PS-1000 ar hd TEST POINT FUNCTION 3-9)
| ya-2| one | Te | Ny |
| = | 2 | ty |
| +5v | TPs | sy |
| eno | Tes | ey |
TPS ‘GND
TO SHIELD HSA-1000
aupio 1/0 }93-3
aupio GNo}YS-2.
: 3c AUDIO}Y3-6 ac TPI TR2 TP3 TP4 TPS TP6 TP? TPB
Vsu-1000 LEFT W8-10 560
RIGHT 35-9 |p
uP 8 lpasaz
DOWN 5-7 |p yags FIRE __J5" 6} pagpq ISTART 6-10] 4959
2START _J6-9 logge,
con2 6-3] O66 VIA ‘SOLDER LUG TO COLOR MONITOR 120 VAC_ISOLATED (—pj-¢-)
120 VAG ISOLATED “Si-g)
TO SHIELD
TO SHIELD EARTH GND ih ‘o00Pr]_ ‘Trooorro FOUR POSITION 500V SOOV. 2A. SB TERMINAL STRIP IL I IN_CLIP ‘AC HI OVD a)
RIP JUI vi 1! FILTER LINE VOLTAGE (JUMPERS
| PREZ HW 1 | 7 | SHOWN 120 VAC OPERATION) |
i
| PRI2 LO | __} | AC LOW | Pr?) |
TEST POINT FUNCTION LOCATION sync
| GND | 1F | da-1 | ea | J8-4 ) | |
| ao | 3A | owe | ger | rrr | om |
| We | 1c | BSC-1000 | 9-5 | 34-6 | |
| WEMRD, | 1D | GREEN] | GREEN | Cie) |
Reo}
| emp | 4-4 | SPEAKER LO | aes | ||
| To | a | VIDEO GND | |||
| SHIELD VIA | 4210 | ve-9_) | |||
| SOLDER LUG | VOL CONT LO | a | |||
| TEST POINT FUNCTION LOCATION | COIN DOOR COMMON. | sec? | |||
| TPl | TORQ | Ic | GENERAL _ILLUM. | a | |
| Te2 | ADDI | 26 | |||
| TP3 | CPU | 2H | GENERAL ILLUM. | (mas-2) | |
| TR4 | 9S MHZ | 3H | +i | RCR-1000 | VOL. CONT. HI |
| TPS | SMDEL | 4G | 15-3) | ||
| TPE | CPUWRITE | 4G | BOOKKEEPING | ros | |
| TPS | <5V | 6H | aeN | 15-9 | |
| TRIO | +5V | 5H |
TPll = MEMRD 76
| TPI2 | GND | 7H | Son 2 | v5-I1) | |
| TPIS | +12V | 8H | +5V | TWO PLAYER START | Ta) |
ONE PLAYER START 3)
ono f28=2 CONTR!
- PANEL COMMON =p) FIRE
| VFB-1000 | JOYSTICK DOWN | Tro |
JOYSTICK UP =}
JOYSTICK RIGHT IPT)
JOYSTICK LEFT
1725 DIVERSEY PARKWAY. CHICAGO, ILLINOIS 0614 [rare {31a eas TELEX 254657 Seeewre) [ows oncy oo sree
DRAWER WIRING DIAGRAM FRENZY COMPONENT
34D-2196-WD