CATHODE RAY TOMES

Thunder Cross

Thunder Cross (set 1) (Konami, 1988) · Document · 12 pages · 23 sections · original scan

Page 1

“7 KONAMI GP THUNDER ROSS.

INSTRUCTION MANUAL

Page 2

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 3

KIT CONTENTS

Quantity Part # Description

1873003Thunder Cross PCB
1873100Control Panel Overlay
1873101Control Panel Decals
1873200Marquee Styrene
2873300Side Decals
130304Red Joy Stick
130305Blue Joy Stick
230110Red Button
230111White Button
230112Blue Button
630250Palinut
630202Switch Holder
1873400Manual
1 set873401Schematic
140903Kit Harness
140605FCC Cage
140310Clear Plexiglass Marquee
  • *& * IMPORTANT NOTICE x x x

The Japanese Amusement Machine Manufacturers Association (JAMMA) has introduced a new standard in video game P.C.B’s. It was decided that all new products from any JAMMA member will use the same pin print-out on the edge connecter. The edge connector will have 56 pin outs, 28 per side.

Konami Inc. will offer a 56 to 36 pin adaptor P.C.B. available through your distributor. This new adaptor P.C.B. will enable the new 56 pin out to adapt to Konami’s old standard 36 pin out.

Page 4

PUTTING YOUR BEST GAME FORWARD

PREPARATION: For best results, all old graphics should be removed completely from the cabinet. ‘‘Stick-on’’ graphics can be removed by using a hairdryer or hot air “evice. The heat from the dryer will loosen the adhesive, allowing you to easily peel them off—any adhesive residue can be cleaned off with acetone and a soft dry cloth. (DO NOT USE ACETONE ON SURFACES PAINTED WITH FLAT PAINT.) TOOLS YOU NEED:

  • Foaming Aerosol (such as ‘‘Windex’’).
  • Soft Squeegee.
  • X-Acto Knife. SIDE PANEL DECALS
  • Spray area of cabinet where Side Panel decals are to be applied with foaming aerosol or a mild soap solution.
  • Remove protective backing from decals.
  • Position decals into place.
  • With a soft squeegee, beginning from the center of the decal, slowly and evenly press out excess foam until you achieve a smooth finish.
  • Allow to set approximately 2 to 3 hours before handling. Maximum adherence is achieved in 48 to 72 hours.
  • Trim side decal to fit your cabinet.

poe PANEL OVERLAY: . Refer to Recommended Control Panel Layout on page 1.

  • Drill any new holes needed.
  • Plug any holes that will not be used. (A permanent epoxy-filler works well for this step.)
  • Pre-position the overlay prior to removing the backing.
  • Slowly apply the overlay — inch by inch on the control panel, removing the backing as you apply it.
  • Once it’s in place, by using an X-Acto knife, cut around the button and joystick placements. INSTRUCTION/BUTTON DECALS: Apply the Player Instruction, Button and 1 Player/2 Player decals in their respective positions. Apply pressure liberally. Allow to set as long as possible before putting game on location.
NOTE: Maximum adherence is achieved in 48 to 72 hours.

MARQUEE

(WEAR PROTECTIVE GLASSES WHILE TRIMMING MARQUEE) 1/8" Acrylic Marquee should be cut to fit your game. DO NOT remove protective mask until this is done. One way of cutting your Marquee is as follows: (Be sure to protect painted side of Marquee from any surface which may scratch or mar finish). CUTTING WITH A KNIFE OR SCRIBER: Acrylic sheet up to 3/16” thick may be cut by a method similar to that used for cutting window glass. Use a scriber of some kind — a scribing knife such as the one pictured, a metal scriber, an awl, or even a sturdy craft knife —to score the sheet. Draw the scriber several times (7 or 8 times for a 3/16” thick piece) along a straight edge held firmly in place. It is best not to remove the protective masking. Make the cuts carefully using firm, even pressure. For best results make each stroke cleanly off the edge of the sheet. Then clamp the acrylic sheet or hold it rigidly under a straight edge with the scribe mark hanging just over the edge of a table. Protect your hands with a cloth, and apply a sharp downward pressure to the other side of the sheet. It will break along the scratch. Scrape the edges to smooth any sharp corners. This method is not recommended for long breaks or thick material.

Always draw the scribing knife along a straight edge. Break sheet over edge of table after scribing.

P.C.B. CAGE INSTALLATION

Konami, Inc. now supplies a new style P.C.B. cage which is superior to old style cages because of ease of installation. The cage is made of a 32 point stem-stock which is fire retardant. . TO INSTALL THE CAGE:

  • Open cage bottom and secure to desired PC.B. position.
  • Install printed circuit board inside cage using wood screws, screwed through the cage bottom into cabinet side.
  • Close the cage over printed circuit board and secure with latch on cage.
Page 5

THUNDER CROSS TECHNICAL INFORMATION

Thunder Cross requires horizontally mounted monitor. It also generates composite negative sync. If your monitor is composite positive sync, you will have to change to composite negative sync.

To alternate composite positive sync to composite negative sync, use 7404 IC or 74LS04 IC. The signal on the output pin from the PC.B. is a combination of H-syne and V-sync.

NOTE: Please refer to Figure 2.

FIGURE 2: +5V

FROM P.C. BOARD

NEGATIVE COMPOSITE SYNC. (PIN P on P.C.B. EDGE) (+5V and GND should be taken out of the P.C. Board.)

TROUBLE SHOOTING GUIDE

__. OUTPUT TO MONITOR POSITIVE COMPOSITE SYNC.

PROBLEM: POSSIBLE SOLUTION

No Screen or 1). Check +5V line at the P.C.B. Adjust if necessary. Constant Reset 2). Make sure all socketed eproms and custom IC’s are seated securely. Apply light pressure to secure. 3). Check harness to be sure it is not on backwards.

No Sound 1). Check +12V line at the PC.B. 2). Make sure both speaker out wires are connected to the speakers. (DO NOT CONNECT A GROUND.)

Distorted Sound 1). Replace cabinet speaker.

VO Problem (coin 1 1). Do not hook a coin counter to the coin 1 or coin 2 outputs. This doesn’t work or Joystick will cause damage. Up doesn’t work, etc.) 2). Check your schematic for the 74LS253 IC that corresponds to your V/O problem. Check the appropriate pin with a scope or multimeter for a high output (5V), if output is low replace the 74LS253.

CAUTION

DO NOT WIRE COIN COUNTERS TO THE COIN 1 OR COIN 2 OUTPUTS. THIS WILL CAUSE DAMAGE TO THE I/O MICROCHIP 74LS253, COIN COUNTERS CAN ONLY BE WIRED TO COIN COUNTER OUTPUTS.

Page 6

THUNDER CROSS WIRING HARNESS

WIRE COLOR KEY: Solder Side

BLACK

BLACK

RED

RED

SRRGNK ORANGE

BRevINEEhIOW

WHITE/BROWN

WHITE/GREEN

WHITE

RED/YELLOW

ViQLETIWEITE

RED/GREEN

BLUE/YELLOW

VIOLET/YELLOW

ORANGE/GREEN

ORANGE/YELLOW

BLACK/YELLOW

ORANGE/GRAY*

BROWN/WHITE

GREEN/YELLOW

BLUE/GRAY

BLACK

BLACK NOT USED

+12V DC

"KEY

(EMPTY)

SPEAKER

(EMPTY)

VIDEO GREEN

VIDEO SYNC

SERVICE SW

(EMPTY)

GOIN:2

2P START

2P-UP

oo, 2P DOWN

2P LEFT

2P RIGHT

2P SHOOT

2P SUPER WEAPON

NOT USED

NOT USED

NOT USED

GND

GND Parts Side

+5V DC

+5V DC

NOT USED

+12V DC

*KEY

COIN COUNTER 1

(EMPTY)

SPEAKER

VIDEO BLUE

VIDEO GROUND

(EMPTY)

COIN 1

1P START

1P UP

1P DOWN ‘/

iP LEFT

1P RIGHT

1P SHOOT

1P SUPER WEAPON

NOT USED

NOT USED

NOT USED

GND

GND

(BASE COLOR/LINE COLOR) BLACK

BLACK

RED

RED

ERE, ORANGE

GREEN/GRAY

YELLOW/GRAY

RED/WHITE

BLUE/WHITE

BLACK

BLUE/BROWN

~ PINK/YELLOW-

ORANGEMPHITE

BLACK/WHITE

RED/GRAY

GRAY/WHITE

PINK/WHITE

GREEN/BROWN

RED/BROWN

WHITE/BLACK

WHITE/VIOLET

BLACK

BLACK capes

Page 7

PARTS SIDE

[SOLDER SIDE

1A sav Ds sv 3 powcr an i SUPPLY +12 SE tev | — ia +92V

on

REQUIRED POWER CAPACITY

| COIN COUNTER 1 & COIN COUNTER 1 [_ cow COUNTER 2 J] COIN COUNTER 2

i t RED iz RED

GREEN N] GREEN

COLOUR MONITOR BLUE 13 BLUE SYNC P] sync No 1a VIDEO GND FR] service

fi 2P START 1p START comne comm fi SERVICE 7 Ss COIN 1 T) cow 2

1P START

UT) ar start 4p uP

2p up BAME AB 1P CONTROLS ET Yee oF LEFT WT) 2 vow 2 RIGHT ea iP LEFT 2 SHOOT —1%] 2 Lert 2PoP. CON. al 1P RIGHT YO] ap RiGHT

CONTROL FOR 2p

22 1 SHOOT Z} 2P sHoot Fz 1P OP. CON. a] 2 oP. con.

CONTROL FOR 1P (a

1p UP. oP. CON. 1P_ DOWN 25.

SHOOT [1p LEFT —e RIGHT 1P_RIGHT 26

LEFT 1P_SHOCT uP 1F OP. CON. 2 Ed own . 26 NO L] sw

~ NOTES - 4 {4 is 1 gf 16: Most “PLAYER: GAMMA SPIN EDGE CONNECTOR 2 1S NO.2 PLAYER 5/32 INCH PITCH

2 SURGE KILLER DIODES FOR COIN

COUNTER INSTALLEO ON THE P.C.B.

Page 8

1.0

2.0

3.0

4.0

5.0

6.0

7.0

MONITOR INFORMATION

SERVICE INSTRUCTIONS

NOTE: All monitors are equipped with automatic degaussing coils (L701) which demagnetize the picture tube every time the monitor is turned on after being off for a minimum of 5 minutes. Should any part of the chassis become magnetized it will be necessary to degauss the affected area with a manual degaussing coil. Move the coil slowly around the CRT face and all surrounding metal parts. Then slowly withdraw for a distance of 6 feet before turning off.

BLACK LEVEL CONTROL ADJUSTMENT This control has been set at the factory and should not need further attention, however, when the game is connected a slight adjustment of VR201 may be necessary to obtain the proper black level (the black portion of the picture just extinguished). VERTICAL SIZE (HEIGHT) Location of this control is shown in Fig. 1. This control must be adjusted slowly, if necessary, until the picture or test pattern attains the correct vertical proportions. CIRCUIT PROTECTION A 4.04 pigtail fuse, mounted on the Main Board has been provided to protect the Power Output Circuit. Focus Adjust the focus control, located on the HV unit (1352), for maximum over-all definition and fine picture detail. HORIZONTAL HOLD CONTROL ADJUSTMENT, VR351 (See Fig. 1) A warm-up period of at least five minutes should be allowed before alignment is carried out. With the monitor being driven from the game signal, short TP601 to TP31. Adjust VR351 until the picture stops sliding horizontally. Remove the short. HORIZONTAL VIDEO POSITION If the video is off center on the raster some compensation can be made by adjusting this control. VERTICAL RASTER POSITION ADJUSTMENT If the video is off center vertically, (short dimension of picture tube) some compensation can be made by moving the vertical raster position adjustment jumper to either positions ‘‘U” or ‘‘D’’. HORIZONTAL RASTER POSITION ADJUSTMENT If the video is off center horizontally (long dimension of the picture tube) some compensation can be made by moving the horizontal raster position adjustment jumper to either positions ‘‘R” or “‘L’. sNEG H SYNC + NEG V SYNC 9.0 HORIZONTAL WIDTH ADJUSTMENT The horizontal width coil is a hexagonal tuning tool adjustment. This control must be adjusted slowly, if necessary, until the picture or test pattern attains the correct horizontal proportions.

  • KONAMI GAMES ARE ALL NEGATIVE COMPOSIT SYNC. USE THE THREE PIN CONNECTOR ON THE MON!TOR

GRN 9 rive '9

RED CUTOFF GRMN CUTOFF’. BLU CUTOFF

WHEN USING COMPOS- ITE SYNC USE HORIZ. SYNC INPUTS, POS H SYNC: POs V SYNC. HORIZ. wiOTH

BLU. crn HORIZ HOLD RED BLK LEVEL

A ers

HORIZ VERT VERT VERT HORIZ

CENTERING SIZE HOLD RASTER RASTER SHIFT SHIFT.

FIGURE 1

Page 9

DIP SWITCH NO. 1 SETTINGS

  • COIN SWITCH NO. 1 SETTINGS

DIP SWITCH SETTINGS

DIP SWITCH NO. 2 SETTINGS

1, PLAYER'S BASIC ENERGY

sw1234 | COIN | PLAYsw12NUMBER
© | orf | OFF | OFF | OFF | 11OFF | OFF2
ON12°ON3
OFF | ON13OFF | ON5
ON14ON7
OFF | OFF | ON | OFF15
  • BONUS LIFE AVAILABILITY
ON16
sw3AVAILABILITY
OFF | ON17
r4O | OFFNO
ON21

ON YES

OFF | OFF | OFF | ON23
ON253. BONUS LIFE (Turn SW3 ON when you use this setting.)
OFF | ON31sw|4]5BONUS LIFE
ON32OFF | OFF | AT 30,000 PTS AND THEN EVERY 200,000 PTS
OFF | OFF | ON | ON34©[ONAT 50,000 PTS AND THEN EVERY 300,000 PTS
ON41OFF | ON | AT 30,000 PTS ONLY
OFF | ON43ONAT 50,000 PTS ONLY

ON FREEPLAY FREEPLAY: You can play games without coins. 4, DIFRIGUETY“OF THE GAME

sw67DIFFICULTY

OFF | OFF EASY NORMAL

2. COIN SWITCH NO. 2 SETTINGS°an
sw5678 | COIN | PLAYOrr | ONDIFFU

ON VERY DIFFICULT

O | OFF | OFF | OFF | OFF11
ON125. SOUND IN ATTRACTIVE MODE
OFF | ON13sw8SOUND
ON14OFFOFF
OFF | OFF | ON | OFF15°ONON
ON16SWS is not used.
OFF | ON17
ON21Ip GWITCH NIN. 4 SETTI_Noe

DIP SWITCH NO. 3 SETTINGS

OFF | OFF | OFF | ON23as
ON251. VIDEO SCREEN FLIP
OFF | ON31‘Sw1
cl72Oo | OFFNORMAL
OFF | OFF | ON | ON | 34ONUPSIDE DOWN
ON41
OFF | ON432. CHANGE OF MODE
ONVOIDsw3MODE

O | OFF GAME ON TEST SW2 and SW4 are not used. O shows recommended settings.

Page 10

THUNDER CROSS TECHNICAL INFORMATION

TECHNICAL INFORMATION

  • Required power capacity GND-Vec 5V 4A or more GND-(+12V) *See the Wiring Diagram.
  • Output R (red) analog, positive G (green) analog, positive B (blue) analog, positive SYNC. H-V complexed, negative
  • The monitor should be horizontally installed.
  • Use the volume knob on the PCB to adjust sound level. Turn the knob clockwise and it becomes louder.
  • Handle with care. SELF TEST

Normal: OK will be displayed. Then the game will start. Abnormal: BAD will be displayed and self test will repeat itself.

MANUAL TEST

  • How to start Turn on the power while the SW3 of the DIP SWITCH No. 3 is on. Push player 1 start button to change items.
  • Test items
  • ROM check
  • Picture contortion
  • Color check
  • VO check 5. 6. . Sound check . Dip switch settings *Push 1P SHOOT button to change sound code.

RECOMMENDED CONTROL PANEL LAYOUT

1P START bo

BLUE JOYSTICK SHOOT WEAPON

2P START.

RED JOYSTICK

Page 11

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 12

USER INFORMATION

WARNING

F.C.C. REGULATION COMPLIANCE

THIS KIT IS INTENDED FOR USE ONLY ON COIN-OPERATED VIDEO GAMES MANUFACTURED AFTER OCTOBER 1, 1983 WHICH HAVE BEEN VERIFIED FOR COMPLIANCE WITH RE- QUIREMENTS IN PART 15 OF F.C.C. RULES FOR A CLASS A COMPUTING DEVICE.

IMPROPER CONNECTION OF THIS KIT OR CONNECTION TO ANY OTHER GAME NOT SO MANUFACTURED OR VERIFIED FOR COMPLIANCE MAY CAUSE UNACCEPTABLE INTER- FERENCE TO RADIO AND TV. RECEPTION, REQUIRING THE OPERATOR TO TAKE WHATEVER STEPS ARE NECESSARY TO CORRECT THE INFERFERENCE.

THE PC. BOARD CAGE SUPPLIED WITH THIS CONVERSION KIT MUST BE UTILIZED AND TERMINATED TO GROUND AT THE TIME OF INSTALLATION.

od KONAMI"

815 Mittel Drive, Wood Dale, Illinois 60191 Telephone: (312) 595-1443, Telex: 6871385 KONAM UW, Fax: (312) 595-2973 For Technical Assistance Call Toll Free (800) 222-6181 (Outside Illinois)