Star Trek
Star Trek (Sega, 1982) · Manual · 149 pages · 55 sections · original scan
SIAR TREK.
Owner’s Manual
Manufactured By
SEGA
TLX 910-335-1621
STAR TREK™ Owner’s Manual Copyright © 1983 by SEGA Electronics, Inc., All Rights Reserved STAR TREK™ Indicates a Trademark of Paramount Pictures, Inc.
TABLE OF CONTENTS
Introduction... . 2... 2... ee ee a 1 Game Set-Up and Inspection... .... 2... 2... . 0. ee ee 2 Specifications and Important Notes ...... we eee wee 3 Game Concept... 2... . ee ee 4 Scoring ..... ee ». 6 Option Selection. ......... ee eee ewe mene d Self-Test 2. 6 6 eee ee ee ee ee -. 10 G-80 Bus Detail .... 1... se ee see ee ee 14 G-80 Mother Board Bus Pin Assignments ............. 15 Troubleshooting Procedures... . 2... ee eee eee eee 29 Color X-Y Monitor and G-80 Circuit Description. ........ 33 Color X-Y Monitor Block Diagram . 2... 2... .. 2... ee 38 Circuit Description Illustrations ............2.4. 49 Adjustments and Specifications ...... a 50 Universal Sound Board Circuit Description ......... » . 53 STAR TREK™ Sounds... . ee ee ee ee ee soe ee ee 54 Sound Block Assignments ... 2... 2... 5.000047 wee 55 Parts Catalog . 2... ee eee ee eee eee eee see 56 Schematics . 2. 1 ee ee ee ee ee a ee - . . 130 Cabinet Wiring Diagram . 2... 2... eee wee ee ee. 130 Sub-Assembly Wiring Diagram... ... 2... me ee ee - 131 Single Player Control Panel Interface... ......... 132 CPU Board... . ee ee eee Pe 133 EPROM Board... .. a 135 X-Y Timing Board . 2... . ee ee ee 136 X-Y¥ Control Board... 1. ee ee ee 139 Speech Board ... 1... ee eee ee ee woe . 141 Universal Sound Board... 2... eee ee ee ee eee 142 G-80 Power Supply... 2. we ee 145 Color X-Y Monitor...) ee ee eee 146
INTRODUCT ION
STAR Trex™ is a microprocessor based coin-operated electronic game, that makes extensive use of digital integrated circuitry and television monitor concepts. This manual is designed for the use of the maintenance technician who possess a general working knowledge of solid-state circuitry and video monitor theory. Any individual NOT knowledgeable in these areas SHOULD NOT attempt repair of the electronic portions of the game. In addition to this manual and training in electronics, troubleshooting and repair will be facilitated by: access to general electronic-type handtools, a multimeter, a 50 to 100 MHz oscilloscope and a logic probe would be helpful. Technical assistance is available toll-free by calling: 1-800-854-1938 outside California 1-800-722-8576 inside California Parts information assistance is available toll-free by calling: 1-800-854-1900 outside California 1-800-722-8575 inside California
Questions or comments concerning STAR Trex! or any of our games are
welcome and should be directed to: Customer Service Manager SEGA Electronics, Inc. 16250 Technology Drive San Diego, California 92127-1985
GAME SET-UP AND INSPECTION
- Inspection
- Before plugging in your new game, inspect it closely to spot any possible shipping damage. Check to ensure the graphics are in place, the monitor is not damaged and that the overall cabinet is in good condition.
- Open the rear service door and inspect the inside of the game electronics compartment. Be sure no components or connectors have come loose. Proper connector fittings must be checked before game power is applied. Check all related connectors for good contact. Although disconnected connectors are easily spotted, poor contacts are difficult to locate. The connectors should therefore be pushed in firmly and then loosened to spot poor connections.
- Check to ensure the fuses are intact. There are five fuses (not counting the monitor fuses). One fuse is located on the AC Junction Box. The other four are on the power supply PC board.
- Voltage Selection
Before plugging in your game, make sure that the game voltage is correct for your location. Locate the two leads from the AC Junction Box to the power
transformer. For 110 VAC, they should be connected to terminals 1 and 3 on the power transformer. For 100 VAC, connect 1 and 2, and for 220 VAC applications, they should be connected to 1 and 4. You will also notice on the AC junction box that there is a safety interlock switch. When the front panel is in place the switch is depressed and the game receives power. Removing the front panel, the switch returns to its original position and the power is cut off from the game. For servicing, this switch can be pulled out and power will be restored.
- Game Specifications
Power 100 VAC, 60 Hz (nominal), 150 watts maximum
- Game Specifications (Cont)
Power 110 VAC, 60 Hz (nominal), 150 watts maximum 220 VAC, 60 Hz (nominal), 150 watts maximum
4, Important Notes
- The following note is included in compliance with FCC rules:
tested and found to comply with the limits for a Class A computing device
pursuant to Subpart J of Part 15 of FCC rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment.
Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures may be required to correct the interference.
- Miscellaneous
NEVER remove circuit board connections while power is on.
NEVER replace any components with anything other than exact replacement parts.
DO NOT replace fuses with anything other than proper value. A blown fuse
Gndicates an overload condition withing the game. Replacing the fuse
with a higher value can cause damage to internal components, if an overload occurs.
GAME CONCEPT
STAR TREK™ is a one or two player SEGA Color X-Y video game with computerized speech synthesis. The player finds himself the Captain of the Starship Enterprise, his mission being to rid the universe of a number of threats to the United Federation of Planets.
STAR Trek™ has a unique method of displaying the information vital to the game play. This method involves the separation of the CRT into three completely separate "screens".
Status Scanner
Viewer
The “Scanner" is where the player sees a “top down" or plan view of local space, ‘with the Enterprise always in the center of this screen. The "Viewer" is where the player sees actual "apparent 3-D" images, as if he were looking out the ships front window. The "Status" screen displays player score in addition to Shield strength, number of Photon Torpedoes, and amount of Warp energy remaining.
The game begins by introducing Klingons, Starbases and the Enterprise into the Scanner with an exciting "shrink down" animation sequence. The Enterprise starts with one to four Shields and Photon Torpedoes (switch selectable). By actuating the rotary knob and depressing the Thrust button the player may maneuver about the Scanner screen.
In order to destroy enemies the player may use either of two weapons; Phasers (the Fire button) or Photon Torpedoes. Each has unique properties.
- Phasers are instantaneous, can destroy only one enemy at a time, and are in unlimited energy supply.
- Photon Torpedoes require time to travel, can destroy many enemies, and are in LIMITED supply. Displayed in the Status screen, Photon Torpedo supply appears as a red bar (squares).
For high speed the player may depress the WARP button. While this button is held down the Enterprise moves very quickly and cannot be damaged in any way by anything. A blue bar in the Status screen displays the amount of Warp energy available and shrinks as the Warp button is held down.
The Enterprise is shrouded by an automatic Shield, which protects the Enterprise from enemy fire and collisions. The Shields are displayed in the Status screen as green line segments (a bar). Once the strength of the Shields is depleted, the ship can sustain damage. When damaged, the Enterprise looses ship functions in the following order: Shields, Photon Torpedoes, Warp Drive. If all of these are damaged, the next hit will destroy
the Enterprise and end the game.
In order to repair this damage the player may choose to dock with a Starbase. Docking is accomplished by merely flying into a Starbase, The "DOCKED" message appears, all damage is repaired, and a Shield unit, Photon Torpedo, and some Warp time are added to the ships supplies. Although only four of each supply unit is displayed at any one time, 255 can be collected.
The primary enemy is the Klingon Battle Cruiser, which comes in three colors:
- Red Klingon - ignores the Enterprise and sets out to destroy a Starbase, after which the Klingon turns purple.
- Purple Klingon - ignores Starbases and attempts to destroy the Enterprise by firing plasma energy balls. Purple Klingons will stop a certain distance away while attacking so as not to risk collision. After a certain period of time (depending on round), purple Klingons turn white.
- White Klingons - sometimes known as “Maniac Klingons", these Klingons will move VERY QUICKLY and attempt to ram the Enterprise.
Ant i-Matter Saucers appear randomly and move about the screen in a "confusing" fashion. These saucers can be destroyed only with Phasers. If the saucer collides with the Enterprise, it will attach itself, drain your ships Warp energy, then leave quickly.
After a number of rounds, the player advances to the Nomad round. In this sequence Nomad zips about the screen depositing dangerous mines. The mines
Cause chain reactions which should be avoided. Nomad can only be destroyed with Phasers. Once Nomad has delivered its total load of 30 mines, it waits for the last mine to detonate, leaves the screen and ends the round.
Every 10,000 to 40,000 points (operator selectable) the player is awarded a bonus Shield unit, Photon Torpedo and Warp time unit. The two player game is played with players alternating with each complete round. Whenever a player is eliminated, the other player continues and finishes the game.
SCORING
Points are awarded for destroying enemies and for the “Starbase Bonus".
- Enemies Klingons... 1. ee eee ee ew ew ee 25 + (round number X 25) Points Anti-Matter Saucer... 2. ee ee ee ee ee ee ee ee © 65,000 Points Nomad 2 ee ee ee ee ee eee ee ee ee © + 30,000 Points
- Starbase Bonus - at the end of a round Used Starbase . 2... ee ee ee ee ee = + (rOund number X 250) Points Un-used Starbase . ... 2... + ee ee ~~ (round number X 1,000) Points
OPTION SWITCH #1
VOICE DURING ADVERTISING
NO VOICE DURING ADVERTISING
PHOTON TORPEDOES:
DIFFICULTY:
BONUS
opr ION
4 COIN/1 CREDIT
3 COIN/1 CREDIT
2 COIN/1 CREDIT
1 COIN/1 CREDIT
1 COIN/2 CREDIT
1 COIN/3 CREDIT
1 COIN/4 CREDIT
1 COIN/S CREDIT PBwn =
EASY
MEDIUM
HARD
TOURNAMENT
10,000 pts 20,000 pts 30,000 pts 40,000 pts OPTION SELECTION
x «x Ox < >< > OX x «> x x «x x
>< > > >< >< > OO oOa0O0 oaocoa
eoonln aoooo >< > > OK >< >< >< OK
SWITCH #2
>< >< OK OK oon oa <<
>< >< >< OOK >< >< OK OK ooo 0n
>< >< >< OK > >< KOK =< «KO OX °o
>< >< OK OO <>< OX
>< >< KOK
<> OK OK
OPTION SWITCH SETTINGS - (cont. )
OPTION SWITCH #2
| 1 | 2 | 3 | 4 | 5 | |
| 1 COIN/6 CREDIT | 0 | c | c | c | 0 |
| 2 COIN/1 CREDIT | 0 | Cc | Cc | 0 | 0 |
4 COIN/2 CREDIT 5 COIN/3 CREDIT
| 2 COIN/1 CREDIT | 0 | Cc | 0 | c | 0 |
4 COIN/3 CREDIT
| 1 COIN/1 CREDIT | 0 | c | 0 | 0 | 0 |
2 COIN/2 CREDIT
3 COIN/3 CREDIT
| 4 COIN/4 CREDIT | 0 | Cc | 0 | 0 | 0 |
5 COIN/6 CREDIT
| COIN/1 CREDIT | 0 | 0 | Cc | c | 0 |
COIN/2 CREDIT COIN/3 CREDIT COIN/5 CREDIT Pwr a
| 1 COIN/1 CREDIT | 0 | 0 | Cc | 0 | 0 |
2 COIN/3 CREDIT
| COIN/2 CREDIT | 0 | 0 | 0 | c | 0 |
COIN/4 CREDIT COIN/6 CREDIT COIN/8 CREDIT COIN/11 CREDIT aR wm a
OPTION SWITCH SETTINGS - (cont.)
OPTION SWITCH #2
1 2 3 4 5 6 7 8
1 COIN/2 CREDIT 0 0 0 0 0 0 0 0
2 COIN/4 CREDIT 3 COIN/6 CREDIT
4 COIN/9 CREDIT
X = NOT USED 0 = OPEN C = CLOSED
SELF-TEST
The G-80 system contains a built-in self-test system, activated by depressing the red self-test switch located on the CPU Board. If the cover to the G-80 card cage is in place, the switch can be activated by putting a pen or pencil through the hole provided on the cover.
1.
to Basic diagnostics test sequence:
CPU RAM
Maskable interrupts
First 1K of game ROMs
Video RAM and Hardware multiplier
Player start buttons
Display screen (visual)
All game ROMs
System inputs
Game controls
Sounds/Vo ice
Individualized diagnostics descriptions and procedures:
CPU RAM - tests all RAM on CPU card before proceeding, system needs use this RAM for stack and variables during other tests so if any locations are bad processor will half (halt light will come on).
- Maskable interrupts - video interrupt is enabled through output port bit and all maskable interrupts are enabled inside processor, CPU then executes several HALT instructions to insure that at least one edge triggered interrupt has occured. If no interrupts occur during this test the halt light will remain on constantly. This is the same result as a bad CPU RAM. This ambiguity can be eliminated by checking the vertical interrupt another way. The system reset/power-up logic will also halt if the video interrupt is not functioning, to try this press the RESET switch.
- First 1K of game ROMs - the first IK of the first game ROM will be checked for validity. If this portion of the first ROM is bad the system will not be able to proceed because vital information defining parameters of the game are stored in this first 1K. If an error occurs during this validity check, the CPU will lock up and repeatedly flash the halt light.
- Video RAM and Hardware multiplier - the video RAM is tested first and in the event that it tests good then the hardware multiplier is checked. If the video RAM is good, the message “ALL VIDEO RAM GOOD, MULTIPLIER GOOD" appears. If a bad video RAM chip is found, then the message "BAD VIDEO RAM, CHIP U##" appears on the screen alona with that chip's location. Due to the fact that sometimes a bad video chip causes the display to be erratic, the system also flashes out the bad chip's location on the halt light, over and over again separating the U#s with a one second on pulse.
The hardware multiplier is used in the game to multiply two 8 bit numbers together to form one 16 bit product. This test performs a select group of multiplications, over 2,000 multiplications in actuality, designed to thoroughly exercise the process of multiplication between the software and the hardware multiplier. The messages "GOOD" or "BAD" are the only indication of functionality with respect to this test.
- Player start buttons - one of the two "game start" push buttons on the front of the cabinet is very special. The "one player start" button was designated by the system as a way to terminate the test that is currently being run. The reason that these two buttons were tested relatively early in the sequence, was so that the remaining tests could use the "one player start"
button for a termination signal. To be sure that these two buttons are functioning properly, see that when untouched the status indicated is "0" (for open switch contact) and that when pushed or depressed momentarily the indicated status is "C" (for closed switch contact) during the time the button is down. This notation for switches being in the open or closed state, "0" or "C", will be used throughout the diagnostic sequence whenever the status of a Switch is being displayed on the screen.
- Screen - this test is supplied by the game logic, external to the CPU ROM, to provide a visual indication of how well the display screen is functioning. It tests beam deflection and colors to check that all electron guns are functioning. In the display, you should see some sort of test showing the colors white, red, green and blue.
- All game ROMs - the intent of this test was to insure the integrity of all of the data in all of the game ROMs. At the time the ROMs for a game were originally generated there was an algorithm performed on each 1K block of data. Each of these calculations, a form of CRC (cyclic redundancy check, similar to a checksum), produced one 16-bit word. These words are stored, along with a Gremlin part number, in the first ROM. When this test is run, all of these 16-bit CRC words are regenerated and are compared to the known values stored in the table in the first ROM. If one of these newly calculated values does not match its corresponding stored value, then the system kicks out an error which amounts to the message "BAD ROM" followed by one or more bad part numbers of that ROM that was found in mis-match. If all ROMs are good the screen displays: "ALL ROMS GOOD". Then the system quickly proceeds on to the next test.
- System inputs - these inputs are referred to as ‘system inputs', simply because they control system functions, such as credit accumulation, coinage options, game configuration, etc. The diagnostic user may check to see that the coin switches, service switch, and option dip switches are functioning properly. The open and closed switch notation applies here as described
earlier.
- Game controls - the names of the controls that the game player would use to control the action on the screen is what this test was designed to check. Make sure that when hands are off of the controls all of the switches are open. When a particular control is twisted, pushed, turned or in whatever way activated, watch to see that the status of that control, and only that particular control, changes to reflect the action on the control panel. The screen should display from open to closed.
- Sounds/Voice - just sit back, listen and watch this one. All of the sounds made by the game will be produced and their respective names will appear in the center of the screen. The termination button acts sluggish during this test due to the fact that some of the sounds must be created by subroutines external to the CPU ROM. After completion of this test, the system will return
to the advertising mode.
G-80 BUS DETAIL
TO/FROM COIN MECH/GAME CONTROLS TO RGB MONITOR OR XY CRT
TO SOUND AMP/SPEAKER il
Z80A 4MHZ VIDEO OR
SOUND AND oTO2
CPU BOARD XY BOARDS SPEECH EXPANSION
W/GAME (1 OR BOARDS SLOTS ON AND COIN I/O (1 OR MOTHER BOARD
2 SLOTS)
G-80
G-80 MOTHER BOARD BUS PIN ASSIGNMENTS
EG GROUND
> <x EEEEE wntna tqateadated¢d
<x EEEEECE eanae Bf f£aaqga a |w
Kn iy Joc
EDGINT
OUTPUT
-12V
IK 3
PANEL RESET
eo
SPEECH READY
GROUND
G-80 MOTHER BOARD BUS PIN ASSIGNMENTS
CPU BOARD
GROUND U38 U36 GROUND A15 u38 U36 AT Al4 38 U36 AG
Al3 38 U36 AS Al2 38 U36 AA All 38 U36 AB A10 38 U36 AZ AS 38 U36 Al AB 38 u36 AB 07 u35 u35 D3 D6 U35 U35 D2
D5 U35 U35° D1
D4 U35 U35 Do
WAIT u31 U30 RESET TNT = U31 U31 EDGINT NMT 31 uld. «EXT EXT @ SEL ui8, ul9 U34 GOUT MEMR U34 U34 MEMW TNPUT 34 U34 OUTPUT RFSH = U34 U34 —-MREQ TNTACK 34 aC
+5V +5V
+5V +5V
-5V -5V
+12V +12V
U31 Ke to in us a fry z <x jo
SPEECH READY
G-80 MOTHER BOARD BUS PIN ASSIGNMENTS
EPROM BOARD
GROUND
AI5 U29
Al4 29
A13,— -U24, U30 A12 -u24, U30 All u24, U30
A110 U26
Ag u26
Ag U26
07 u25
D6 u25
05 U25
D4 U25
WAIT
TNT
WMT
EXT @ SEL
MEMR = -U26 INPUT ‘RSH
INTACK
+5V
+5V
-5V
+12V
SPEECH READY
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
ra us [77 us a = fr Zz =< io
SPEECH READY
6-80 HOTHEN BOAR! BUS PIN ASSIGNME
SPEEC
GROUND GROUND
ANS u38 ath u38
Al3 u37
Al2 U37
Aa u37
A1O u30
Ag U24, U30 Ag u24, U30 D7 u21, U24, U27 U20, U21, U24 D6 uU21, U24 U20, U21, U24
DS u20, U21, U24 U20, U21, U24
D4 u20, U21, U24 U20, U21, U24 WAIT U18, U20, U21 RES
TNT ED
NMT EXTS EXT @ SEL 3 MEMR
TNPUT U35, U36 U35, U36 OUTPUT RFSH TNTACK
+5V
+5V
-5V
+12V
-12V
HLT
$/2
PANEL RESET
Oo fe a |o nm |e
SPEECH READY
GROUND GROUND
G-80 MOTHER BOARD BUS PIN ASSIGNMENTS
X-Y TIMING BOARD
GROUND
AIS
Atk
Al3
Al2
All
A1O
Ag
INT U40
NMI U30
he us a i a fre Zz <x a.
SPEECH READY
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
> nN -12V
Kg
PANEL RESET
FETCH U42, U48, U49
cc jo U23, U34
7 .5Mbz U44, U4S
a PC U32, U34
SPEECH READY
GROUND GROUND
star TREK™ TROUBLESHOOTING PROCEDURES
STAR TREK is a "State-of-the-art" electronic microprocessor based, video game. The result of hundreds of hours of work, design, research, experiment and more work. However, as with any electronic device, component failure or other problems can result in a game that doesn't function properly, or doesn't function at all. In either case, your game is "down", and so critically, are your profits.
Your objective is to fix it as quickly as possible, and logical troubleshooting goes a long way toward that repair. Although many troubleshoot ing methods may be familiar to you, procedural logic is common among them, and might be stated in this order: visual inspection, symptom recognition, symptom isolation, function isolation, component isolation and repair. Familiarity with the equipment in question will allow you to bypass one or more of these steps, as any particular problem may be obvious to you, or may have happened before. In general though, these 6 steps form a good premise upon which to approach your “down" game.
An extremely important item in our procedure is the first mentioned, giving the gear the “once over". A large percentage of failures found in electronics, show themselves visually and often a great deal of time can be saved by inspecting for burnt or blown components, loose or disconnected wiring or connectors, or PCB traces burnt or pulled up. Thorough visual inspections become increasingly important the closer you get to the faulty item, and should be repeated each time another portion of the game is eliminated. Symptom recognition (as with all electronic troubleshooting) in your game depends first, on knowing what a proper display is, and second, knowing how your display differs from a normal one. Symptom isolation follows naturally; (i.e., "T have no picture", "I have no sound", "I have no control over the car", "the picture is scrambled"), ergo, a video, audio, input or logic problem. Function isolation, such as a sync problem with the video, requires that you consider those functions that go to make up video sync. Is it a monitor problem, or an "on-the-board" problem? A monitor input check to verify the signal will tell you. Does the board have the voltage (from the power supply) that it needs? Yes? We must have a board failure, as we've just isolated down to function.
Taking our sync problem further, before we begin our search for an individual component, let's reapply that first item in our "Logical Troubleshooting Procedure". Look at the board. Open resistors, diodes, and capacitors often give themselves away.
Noticing a trace literally burned open can save you serious "down-time". The board looks OK, so on we go. Specific component isolation relates to the specific nature of the failure, component commonality, proper inputting (both signal and power) and proper outputting (as in the case of an output held high, low, or floating by input port failure in the succeeding state). More general problems (such as a total loss of video sync) requires the more involved Procedure of systematic elimination of possibilities. This operation can be expedited however, by dividing the circuit in half, establishing a "go-no/go" at that point, and again dividing the suspect circuit portion in half. The largest possible areas can be eliminated in this manner, dividing and subdividing until the individual component failure is found.
As we've outlined previously, any electronic repair procedure consists of a series of efforts to isolate a problem down to a “managable" level; restating our Logical Troubleshooting Procedure in 6 steps, 1. Visual Inspection, 2. Symptom Recognition, 3. Symptom Isolation, 4. Function Isolation, 5. Component Isolation, and 6. Repair.
In our STAR TREK game system, we are dealing with, essentially, 3 major func- tional components:
- The Power Supply
- The G-80 Boards (Card Cage Module)
- The Color X-Y Monitor
So, in a typical maintenance procedure, having isolated down to Function (Step 4.), we would next attempt to determine which of the 3 major elements is defective. In the following paragraphs, we will look at each element and some of its sub-divisions as a guide in isolating further.
Usually, the power supply can be eliminated as the source of a problem if the games comes up on the screen. The major exception is when the game plays normally but no sounds are produced. In this case, the power supply's amplifier circuit should be checked for audio signals from the sound and speech boards. If they are present on the amplifier output, then a bad speaker or connection is probably the cause of the problem. If the signals are not there, suspect the amplifier circuits on the sound and/or speech boards.
If the picture does not appear on the screen, check the power supply for the main AC voltage to the primary of its transformer; then ensure that the G-80 boards are supplied with the correct DC voltages from the power supply. Also make sure the 3 VAC reset signal is being applied to the CPU board. If all these tests prove normal, then eliminate the power supply as cause of the problem and proceed to check the remaining functional game components - G-80 boards and monitor.
In most cases, a simple test will help to isolate a problem of no picture to either the G-80 boards or monitor. On an oscilloscope, look for varying voltage signals on pins 1 and 4 of the 4-pin Molex connector on the Timing Board. If the signals look similar to those shown in Figure 1, check for signals swinging between 0 and +4 volts on the RGB outputs (4-pin Molex connector pins 4, 1, 2 respectively) on the Control Board. If all three outputs are at 0 volts, suspect the X-Y boards. If the signals appear normal, suspect the monitor as the cause of the problem. If however, pin 1 (to the monitors horizontal input) is held at or near +4 or -4 volts DC, suspect one or both X-Y boards. If pin 4 (to the vertical input) is held at or near +3 or -3 volts, suspect the other G-80 boards. In either case, TURN OFF THE POWER AND IMMEDIATELY DISCONNECT THE X-Y MONITOR. Proceed to check the inputs to D/A converters U1 and U4 (T5) for active signals. Verify that none of the Character Data lines (CDO-CD7) are pulled high or low, or are floating. Check for the XCL and YCL clock signals from U28 (16). Verify that the 15 MHz crystal clock is operating and that a 40 Hz signal is present on pin-11] of U13 (17). Check BOS signal to be sure it is not held; signal DRAW should be switching high and low. On the Control Board, observe the signal FETCH to ensure it pulses high and low. Also, none of the Data lines (D0-D7) should be held high, low, or floating (C5). Check for clock signals PCC and SCL (C5).
Look for input changes on U1 and U5 of the color circuit (C6); also, pin-3 of U4 should be active high and low. (See figure 1 in the illustrations section).
When the monitor is suspected of a problem, check for all correct power supply voltages as shown in the schematic. Isolate incorrect voltages to either the monitor power supply or to the circuit receiving the voltage.
EXCESSIVE DEFLECTION CURRENT THAT COULD SEVERELY DAMAGE THE MONITOR. For
testing the monitor, use only the outputs of the G-80 hardware. In addition, DO NOT operate the monitor WITHOUT proper fuses in the main AC line. If a
monitor is blowing main fuses, check the deflection amp power transistors Q605, Q606, Q705 and Q706, WITH THE POWER OFF. Shorted transistors or diodes in the deflection amplifiers will also blow main line AC fuses.
Check the transistors in the color drive circuits for shorts or opens when one or more colors is missing from the display, and the G-80 boards are known
to be good.
COLOR X-Y MONITOR AND G-80 CIRCUIT DESCRIPTION
To begin our discussion of the Color X-Y Monitor, let's first pay tribute to the “other kind of monitor" - the raster-scan. As you may remember from your knowledge of raster-scan displays (like those in a TV), that the electronbeam inside the tube always moves in a predictable way. That is, it always starts at the top left of the screen and scans across it, forming a pattern of horizontal lines on the inside surface of the tube as it moves downward. When
it gets to the bottom, the beam is forced back to its starting point and repeats the raster-scan movement. To create a simple display (for example, a large "+" symbol) on the raster-scan monitor, we figure out first, where we want it to appear on the screen; let's say the center, in this case. Then we generate a video signal that represents the "+", plug the signal into the monitor, and we get a "+" on the display. What we have done is intensify the electron-beam so that only those points corresponding to the "+" light up on the raster. (To see how it would look close-up, refer to figure 2 in the illustrations section.)
Notice how the vertical line is not much of a line, but more a column of stacked lines. This occurs because the raster lines, which run horizontally inside the CRT, are spaced slightly as the beam traces them. So what we see, looking at our line from top to bottom is a tiny segment of the lit up raster, then a black space, another lit up segment, another black space, and so on. Now the horizontal line of our figure is perfect, one solid, lit up line corresponding to that particular "raster". The fact that you can't get highquality traces in both directions is what led to the development of the X-Y monitor. If we create that same centered "+" on an X-Y display, we would see two perfect, solid lines - no gaps anywhere. (Refer to figure 3.) What produces the high-quality, solid lines in any direction in an X-Y monitor is the electron-beam inside the CRT (there are actually three electron-beams, one for each of the three colors, red, green, and blue, although it is often simpler to think of it as one beam). Unlike the beam in a raster-scan unit, the X-Y beam can be moved in any direction we choose. All we have to do is determine where we want to move it. We also need to tell the beam when to turn on, or intensify, to “draw” the design we want, how big to make the
design, what color the lines should be, what angles the lines will take, and when to stop drawing. For now, remember that we are directly influencing the X-Y beam to create our lines by moving it and turning it on when necessary; in the raster-scan, all we had to do was turn on the beam at the right times.
Before we delve into the circuits that make up the color X-Y monitor, let's consider how we actually control an electron-beam. Inside the picture tube neck, there is a piece of metal called a cathode. When it is charged with a voltage, it generates electrons. As the electrons are emitted, they are shaped to form a thin ray, or beam, that strikes the front of the monitor. The only way the beam will move up or down, left or right is if a magnetic field is applied around the beam. This is what the deflection coils located around the CRT neck do. There are two coils, one to move the beam up or down (VERTICAL DEFLECTION COIL) and one to move it left or right (HORIZONTAL DEFLECTION COIL). So, by running some current through either coil, we create a magnetic field around the beam to deflect it in any direction. The larger the current we put through either coil, the stronger the magnetic field and the more the beam will deflect.
While we're on the subject of beam movement, consider why this monitor is called an "X-Y monitor". Picture our "+" symbol on the screen again; the horizontal line is called the "X" axis and the vertical line is the "Y" axis,
hence "X-Y monitor". Make a mental note that when we move the beam horizontally, we are moving it on the X-axis; moving the beam vertically occurs on the Y-axis. Let's look closer at the color X-Y monitor circuits and see where this deflection coil current comes from. (For the following explanation, please refer to the schematic of the monitor in this manual.) The circuitry primarily consisting of IC 600 (15-2156-01) accepts two varying voltage levels, one for Vertical, one for Horizontal, from the G-80 boards. These
voltages are called ANALOG signals because they represent all voltage levels between two pre-determined levels.
Let's say that we want an analog signal that can vary between two voltages, +3 and 43 volts. We could control it to look like this on an oscilloscope:
/ +3v
By
As the signal changes, it moves through all possible voltage levels that exist between +3 and -3 volts. Don't confuse this type of signal with a digital one. The digital signal switches between 0, and typically, +5 volts. It does not drop to a negative voltage level. As these varying voltages come into the X-Y monitor, they activate, first the Input Driver, intended to set a proper reference, and the X and Y power amplifiers (Q 600-606, Q 700-706). These amplifiers control the current that flows into the X and Y deflection coils, depending on the voltage levels on the inputs, and the input current set by Limiters Q 201, 202, 251, 252. Remember that this current controls the electron-beam movement, so if we vary the input voltage, we vary the output current and the direction of the beam. The following chart will clearify this:
INPUT VOLTAGE BEAM MOVEMENT
| Y-AMP | Positive | Up |
| (Vert ical) | Negative | Down |
| X-AMP. | Positive | Right |
| (Horizontal) | Negative | Left |
Earlier, we said that there has to be a way to turn on, or intensify the electron-beam to create an image on the screen. Well, there are three more inputs to the X-Y that allow us to do just that; they are the color inputs R,G,B and they accept analog signals from the G-80 hardware. These color
signals activate the three color electron-beams through the circuits in the Video PCB. Using what we know so far, let's apply it to an actual example of drawing something simple on the screen - a white line for instance. (Refer to figure 4 - illustrations section.)
Point A, the center of the screen, is the starting point for the electronbeam. To move the beam to point B, we have to supply voltages to the monitor's inputs that cause the beam to move at a 45 degree angle. To do that requires two increasing positive voltages on the horizontal and vertical inputs. (See the chart above). Not only are these voltages positive in this case, they also have to be equal. And if they are equal, the deflection coils will force the beam the same distance both upward, and to the right, at the same time. Moving at any other angle is just a matter of making one coil deflect more or less than the other. Again, notice that both coils force beam deflection simultaneous ly.
Since we don't want this 45 degree line to show up on the screen, we don't feed any voltages to the RGB inputs. But, we know the beam is at point B, awaiting further deflection. Now, we cause the voltage on the horizontal (X) input to go negative and leave the vertical voltage where it is. Also, we turn on the RGB inputs to give us a white line. From the chart, you can see that these voltages will cause the beam to move to the left, horizontally, to point C. Our line is complete, and here is what our input signals looked like
during this process:
+V Horizontal (X) o .. Voltage S.
Vertical (Y) Voltage
-V
Ry +V -- JL B oe
In our example, we made a very short line, considering we could have drawn one clear across the screen. In order to draw longer lines, in any direction, we simply increase the positive or negative voltage on the inputs. Remember the higher the voltage, the more the deflection, the longer the line.
The remaining circuits in the monitor are a power supply, a CRT and brightness contro] (CRT PCB), and high voltage generator. Here are Functional Block, and Signal Flow diagrams for the Color X-Y Monitor:
A
INPUT DRIVER
COLOR X-Y MONITOR
MODEL G08:
X-AXIS.
LIMITER
REF 1] REF ner [7-17] rer
CURRENT
VIDEO PCB
Q 100-105
CRT i [el=[~o]-]=e) g é HI < g
Refering back to the monitor schematic for the following discussion, the circuitry in block A serves two purposes. First, it compensates for a type of distortion known as the pin-cushion effect. This occurs because the electronbeam must travel a greater distance when striking the edges of the CRT than when it hits the center. If we cause the beam to trace along the edges of the CRT, the beam would draw a box with its left and right sides bowed inward. To compensate for the effect, this circuit offsets the point where the beam would normally strike the CRT surface.
Secondly, this circuit contains two error amplifiers, one for the horizontal and one for the vertical inputs. Each error amp has two inputs; one is set to zero volts, the other accepts the analog signal from the G-80 system, sensing current movement in the deflection coil. The analog signal is allowed to pass through the error amps and drive the deflection (power) amps. The deflection amps are shown in blocks B and F. The outputs of the X and Y power amps pass current through their respective deflection coils. The output leads of the two coils are connected back to the analog inputs of the respective error amps, as mentioned above. This acts as an error, or feedback, signal and ensures that the current through the deflection coil remains proportional to the voltage on the error amp inputs. If this signal were not provided, there would be a Slight deflection error when an analog input signal was present.
The outputs of the X and Y deflection amps can swing between +60V and -60V. This voltage is high enough to provide up to 8 amps, peak-to-peak, of current through the deflection coils.
The color drive circuits are located in schematic block C and they accept a 4 volt maximum signal on the RGB inputs. The outputs drive the three electron-beams in the CRT. Three neon glow-bulbs, NE-100, 101, and 102 act as spark arrestors for the color-drive outputs to the CRT. In block D, the CRT is shown, as well as the brightness adjustment for it. The circuit of D 409, R 411; R 410 is a spot-killer that prevents the electron-beams from burning a hole in the phosphor surface of the CRT when the monitor is turned off. Section G of the schematic consists of the high-voltage oscillator in IC 900 (14-2155-01) which operates the high-voltage transformer, T 901. This transformer is technically a flyback type, but it is not used to deflect the beam.
The IC serves two other functions; it senses the presence of the 10.3KV through R 921 and R 932 and compares it against the 9.1 supply voltage to ensure a regulated output, and also senses the varying current in either deflection coil. If no change is detected, the IC shuts down the high-voltage oscillator to prevent the beam from "burning" the face of the CRT.
Finally, the X-Y power supply is shown in block E, generating the following voltages: +60V to X-Y power amplifiers +55V to RGB video drivers and spot killer +9.1V to the IC's +120V. to the EHT oscillator
A degaussing circuit is provided through D 404, D 405, and R 400. The CRT is automatically degaussed when R 400 is cooled sufficiently to conduct current through the degaussing coil.
G-80
It's not hard to imagine how fast the input signals to the color X-Y monitor must be changing in order to produce the game displays. It's also obvious that a computer must be making all this happen. That is exactly the case with the G-80 hardware used in Color X-Y game. It contains two new boards, the X-Y Timing and X-Y Control boards that produce the X-Y monitor input signals. The G-80 still relies on its CPU, EPROM, Sound, and Speech boards to complete the computer.
But what does a digital computer have to do with producing the analog signals required by the X-Y monitor? Basically, the computer converts certain digital signals into analog ones. On the G-80 X-Y boards are circuits (some are actually single IC's) called Digital-to-Analog converters, D/A for short. These circuits accept a particular digital word, that is, a string of O and +5V voltage levels. The D/A converter senses the word and outputs one and only one voltage level which corresponds to the digital word. For example, we could design a simple D/A converter that would generate the following voltages when we input certain digital words:
DIGITAL WORD ANALOG OUTPUT
0000 -1 Volt
W111 +1 Volt 1000 0 Volt
This is a very basic case, but it shows that, for a particular D/A converter, we always produce one voltage level from the corresponding digital input. If we cycle through a variety of digital inputs, we'll get a variety of output voltages. If we do this fast enough, we actually create a rapidly varying range of output voltages. This output is exactly the kind of signal we need to drive the deflection coils in the monitor.
Now that we know where the analog signals come from, what about the digital ones? Before we can display anything on our X-Y screen, we have to ask some questions: (Answers are provided for examples sake)
QUESTIONS ANSWERS
- What do you want on the screen? A triangle.
- How many? One.
- What design? - What angle? Equalateral (3-60° angles).
- What size? 3" on a side.
- Positioning? Centered on the screen.
- What colors? 2 sides white, 1 side blue.
- Screen alignment? Like this:
BLUE
- What will it do? dust sit there.
- How many lines does the electron- In our triangle, the beam have to trace? beam must make 4 lines:
A (even though we don't see it), B, C, and D.
Now that we have our specifications, we have to store this information someplace so the Timing and Control boards can get to it and understand. That place is video memory RAM (or Random Access Memory). It holds 4096 eight-bit words or bytes. Naturally, we don't place all this into memory and hope the X-Y boards can find it; it's stored in an orderly fashion.
First, we divide the video memory into two main groups - let's call them 1) The Symbol Instructions and, 2) The Line Instructions. Into the Symbo 1 Instructions Section we store one group of ten words for every symbol or design we put on the screen. In our example, we have only one symbol, so we use only 10 words. Into the Line Instructions Section we put one group of four words for every Line that the beam has to draw. So, for our triangle, which requires 4 lines, we would store 4 groups of 4 words in the Line Instructions space. Every word we store in memory has one and only one address, so the same word can be called on over and over. Now let's look closer at the Symbol Instructions memory space. Here is what the 10 words do: (Don't be concerned with
the actual values of those words right now.)
WORD 1 It tells the X-Y boards either to make the beam draw the symbol in this group of words or not to draw it. And the same word informs the boards that either this group of words
is the only group or that there are more 10-word groups to follow.
WORD 2 and 3
WORD 4 and 5
WORD 6 and 7
WORD 8 and 9
WORD 10
Again, since groups after the
of memory:
WORD 1
WORD 2
WORD 3
WORD 4 These tell the boards where the beam is on the X-axis.
These tell the boards where the beam is on the Y-axis. The
last four words then, give the exact coordinates of the
electron-beam.
Words 6 and 7 tell the X-Y hardware what the first address is
of the Line Instructions section.
These tell the hardware how the complete symbol (our
triangle) will appear on the screen, or at what angle.
This word tells what the overall size of the design will be.
we're only making one design, there will be no more 10-word one above. Now take a look at the Line Instructions section
GROUP 1
This word tells the G-80 boards either to blank or to unblank
the line. And, it informs the boards that either additional
4-word groups follow or no more groups follow. Finally, it
defines the color this particular line is to be.
This word represents the length of the line the beam is to
draw.
Word 3 tells the hardware at what angle the beam should make its line. 45°27, 90°?
Word 4 defines in which of the four sections of the screen
the line is to appear - which quadrant.
The remaining 4-word groups contain the same representations of their respective lines, as in Group 1. The values will be different, of course,
depending on how the lines differ. In our triangle example we would find 3 more groups of four words after Group 1.
By now, you may be wondering what all these "words" really are. Since we are dealing with a digital computer, the "words" we described above must be digital. More accurately, they are digital values of the specifications required to create our designs. We have taken the specifications for sizes, angles, shapes, colors and locations and converted them into digital words and create displays that the word represent.
Before we go any further, you should know that the words read from the video RAM didn't get there by magic. The microprocessor put them there. All] words that represent all the characters and designs in a game are kept safely in EPROM (Erasable Programmable Read Only Memory), on the EPROM board. When the game is powered up the CPU moves the various word groups from EPROM to RAM. Once situated in video memory, the words are made available to the Timing and Control boards to create displays. Briefly, here is what the two X-Y boards do with the words:
After all the character words are loaded into video RAM, the Program Counter is forced to call on the first RAM address. Here the Program Counter finds the first word in the Symbol Instructions section. One at a time, these ten words are taken out of RAM and latched into specific parts of the X-Y boards. This sequence is controlled by the Timing Generator which generates 15 act ive-low signals; only one signal pulses low at a time to latch the words. Next, the following sequence occurs:
. Word 1 is latched into U52, Last Symbol block.
- Words 2 and 3 (from the Symbol Instructions) are loaded into the X-axis Up/Down counters.
- Words 4 and 5 are loaded into the Y-axis Up/Down counters.
4, Words 6 and 7 are stored in the Vector Address counter.
- Words 8 and 9 are stored in the Symbol Angle latch.
- Word 10 is loaded into the Serial Multiplier.
Now the first 10 words of a character we wish to display are stored somewhere. If we had not wanted to draw this character, the Program Counter would have jumped to the next set of 10 symbol words, if there were another symbol. Once the Program Counter is finished moving out the words, the Vector Address counter takes control of memory. This switching between the Program and Vector Address counters is governed by the Multiplexer. Through it, the G-80 Address Bus or one of the other counters can address video memory. Only one device is allowed access to memory at a time. When it is the Vector Address counter's
turn to get into memory, the counter addresses the first word of the Line Instructions section. The reason for this, is that the Vector counter was previously loaded with words 6 and 7 in the Symbol Instructions section. These words tell the Vector Address counter the locations of the first word in the
Line Instructions section. Now the Vector counter causes the Line Instruction words to be moved out of memory, one at a time. Here is what happens to the group of four words:
- Word 1 is stored in the Color Latch and in U52, Last Vector.
- Word 2 is stored in the Vector Length counters.
- Word 3 is loaded into the Vector Angle circuit.
- Word 4 is used in the Vector Angle circuit.
Up to this point then, 10 words that describe some symbol and 4 words that represent one line in that symbol have been clocked out of memory. When the Vector Address counter takes out the last group of words that represents the last line to be drawn, memory access is switched back to the Program Counter. It will now either restart the sequence as before (if there is another symbol to be drawn) or it will stop until the counter is reset to the beginning again.
Now the system is ready to draw its first line, to actually move the beam, because we have given it exact specifications to do so. The position of the electron-beam is now known, (Words 2 through 5 in the Symbol Instructions) so
we know where the beam will start to draw. Then, the X-Y boards calculate the length and angle of our first line. And they know the color, if any, of this line. (In our triangle, recall that our first line, A, is one that we Shouldn't see, although it must be drawn. We also know that it must be drawn at a 0° angle, straight up.) The boards calculate the line length and angle
by assigning a certain number of digital clock pulses to these qualities. The circuitry acts as a digital "ruler" and "protractor" and measures any line, in terms of how many pulses in length and angle it is. All this figuring is performed by the Full Adder's, 2708 EPROM and Rate Multipliers. The output of each Rate Multiplier (XCL and YCL) is a string of clock pulses that clock the respective Up/Down counter, X or Y. But the pulses are not just random pulses, they are the digital equivalents of a line with a particular length and angle. So we clock both Up/Down counters at the same time with these pulses. Doing so we force the counters to start counting from the beam position words previously stored in the counters. The important point is this; if we change the digital values of the beam position words, we change the position of the beam through the D/A converters. How far, and at what angle we change the beam depends on the amount of pulses applied to the Up/Down counters. Just before the beam is moved, the color of the line (black included) is sent to the monitor through the RGB D/A converters.
There you have it - one line. For more lines, the G-80 system rapidly follows the same procedure of reading the symbol and line words, latching them, calculating line values, color values, and then forcing the beam line-byline to form complete symbols.
Notice that throughout our discussion, we have mentioned the microprocessor's role just once; loading the character word into memory. During an actual game however, it does more than act as a "loader". Whenever we want to Move our symbols on the screen, for example rotate the triangle, we need some way of changing all those words to represent new lines and angles. The CPU fulfills this job nicely. Under program control, the CPU is told when and how to alter these words to create a whole range of dynamic displays - different colored lines, new angles, longer or shorter lines, bigger or smaller characters, whatever the game play calls for. Also, the microprocessor governs functions such as player control and coin inputs, or sound and speech outputs.
The CPU then, gives us the variety and color in our X-Y games. - PLEASE NOTE: The designations in parenthesis will be used throughout the following detailed discussion to refer the reader to the proper schematics. C = X-Y Control Board (P/N 800-0163) sheets 5 and 6. T = X-Y Timing Board (P/N 800-0161) sheets 5, 6, and 7. e.g. (C6) = Control Board, sheet 6.
The CPU addresses video memory, U24-U31, through multiplexer IC's U48 and u49 (C5). Character words are taken from memory as the Program Counter, ICs U33, U34, U22 (C5), addresses them through multiplexers U36, U49, U35, and U2] (C5). If Word 1 (Symbol Instructions) says to not display a symbol, the Program Counter is advanced 10 counts by U33, a full adder, which adds 10 to the counter when signal ADD goes low. The Vector Address counter is composed of U10, U1], and U12 (C5) and is loaded with the first address of the Line Instructions from video memory's Character Data Bus, CDO-CD7. The CPUs Data Bus, DO-D7, is brought to the memory through a bi-directional buffer, U14 (C5). The signal labelled FETCH (C5) latches the various Character Data words from memory. The MUX (C5) signal commands the multiplexer ICs to allow either the CPU, Program Counter or Vector Address counter to address memory. MEMR (memory read) and MEMW (memory write) come from the CPU board to read from or write to the RAM. Signal VCE (C5), Vector Clock Enable, increments the Vector Address Counter. PCC (Program Counter Clock) is the string of pulses that advances the Program Counter; PCR (Program Counter Reset) ensures that the Program Counter starts counting at the first location in video RAM each time PCR goes low. This signal occurs first at power-up and then 40 times a second during program execution. So, it causes the X-Y monitor to draw and re-draw each symbol on the screen 40 times a second. The signal is generated from the master clock (crystal Y1 and U14, T7) by U31-U34 and U22 (17). The other clock signals (VCE, PCC, FETCH, ADD, MUX, and VCL) are all generated by the X-Y Timing board (17).
The outputs of the Last Symbol and Last Vector latches (U52, T7) are AND gated together with the signal END, which originates from the Control board's U18 (C6). When U18's output goes low, it signifies that no more symbols are to be drawn. Then the Program Counter is reset by the 40 Hz signal to the start of the video memory to repeat the display sequence. U22 (T7) is the DRAW latch and its output, through U21, creates the DRAW signal which initiates a
sequence that causes the beam to draw. This sequence occurs on the Timing Board, sheet 6; by this time, all video words have been stored in their proper places in the system. On the Timing Board (T7), the vector angle is in U56, the symbol angle in U55. So when DRAW goes high, it causes strings of digital pulses that represent the vector and symbol angles to be generated. These streams of pulses (from U28, T6) are the ones that clock the X and Y Up/Down counters, shown on T5 (U15-U20). U25 (T6) tells the counters in which direction to count, up or down (D/U X, D/U Y). Then, the outputs of the Up/Down counters, X and Y, become the digital words that are converted to analog signals by D/A converters U1 and U4 (T5). On Amps U2 and U3 (T5) convert current from the D/A converters to voltage levels. These levels drive the Vertical and Horizontal inputs to the monitor. Signals DRAW and VCL are combined in U28 (T6) to form DCL (Draw Clock). This signal clocks down the Vector Length counters U15, U16 and U17 (C6) which contain words that represent various lengths of the lines to be displayed. When the counters have counted down to 0, the END signal becomes active. As the X and Y Up/Down counters are clocked, their outputs are sensed by U5-U10 (T5), which are multiplexers. The multiplexers are necessary to tell the system when the beam is off the screen. It does this by generating the BOS signal (T5). Then BOS is AND gated with DRAW at U5 (C6), to blank (turn off) the beam whenever BOS goes low.
U3 (C6) compensates for the inherent delay in deflecting the electronbeams. It provides a number of taps to select a range of delay times. From U2 (C6), the color word is read and applied to the RGB D/A converters US, UI and associated diodes and resistors. The RGB outputs go directly to the color X-Y monitor.
U50, a 74LS154 (T7) decoder IC, selects one of 15 outputs by making the output low. The outputs sequentially store the video memory words, one at a time. U50 is enabled at pin 18, forty times per second by U22 (T7), and at pin 19 by U21. U5] sequences U50 through its 15 count cycle; at count 14, pin 16 of U50 goes low to initiate the DRAW signal through U40, U2] and U22 (17).
The circuitry at the top of schematic C6 (U45, U51-U54) is not used in generating and displaying characters on the X-Y monitor. Its function is to perform lengthy calculations under software control.
Illustrations
Raster-Scan Display ————>
: : Nice Line
Figure 1 Figure 2
Figure 3 Figure 4
ADJUSTMENTS AND SPECIFICATIONS
On the X-Y Timing Board, there are two potentiometers that adjust the outputs of the X and Y current-to-voltage converters (U2 and U3, respectively) ; they are:
R3 (X) U2 R6 (Y) U3
On the monitor, there are a number of factory-set adjustments. DO NOT USE THESE CONTROLS. They are:
R106 R917
R117 R918
R611 R920
R702
The following controls can be used to adjust the monitor if necessary:
R605 Vertical
R712 Horizontal
R107 Red
R118 Green
R136 Blue
R930 Brightness R922 Focus
Input specifications from the G-80 boards to the color X-Y monitor are:
Vertical Input 38V maximum
Horizontal Input +4V max imum
Red Input +4V @ full brightness Green Input +4V @ full brightness Blud Input +4V @ full brightness
VOLTAGE ANALYSIS FOR THE GO8-003 COLOR X-Y MONITOR
DEFLECTION PCB
P 900 (EHT) Pin 1 2.8 VAC
2 3.5 VAC
3 -9.1 VDC
4 9.1 VDC
5 GRD
6 GRD
7 5.0 VAC
8 120 VOC
9 OPEN
10 400 VDC
D 401 - cathode 63 VDC
D 403 - cathode 63 VOC
D 400 - anode -63 VOC
D 402 - anode -63 VOC
ZD 400 59 VOC
ZD 401 9.0 VDC
ZD 402 -9.1 VDC
Q 400 - base 59 VDC, - emitter 58.8 VDC, - collector 63.5 VOC
Q 401 - base 9.7 VDC, - emitter 9.1 VDC, - collector 17 VDC
IC 600
| Pin 1 | 0 | 10 | 0 |
| 2 | 4.2 VOC | 1 | 0 |
| 3 | 0 | 12 | -9.1 VDC |
| 4 | 0 | 13 | 0 |
| 5 | 0 | 14 | 0 |
| 6 | 9.1 VDC | 15 | 0 |
| 7 | 7.5 VOC | 16 | 0 |
| 8 | 0 | 7 | 0 |
| 9 | 0 | 18 | 4.2 VDC |
| Q 600 - collector | 34.5 VDC | Q 700 - collector | 35.9 VDC |
| Q 601 - collector | 0.8 VDC | Q 701 - collector | 0.5 VDC |
Q 602
Q 603
Q 604 Q 605
Q 606
EHT PCB
IC 900
Pin
Q 902
Q 903 collector
collector
collector
collector
base
emitter
collector
base
emitter
emitter
base
collector
emitter
base
collector
emitter
base
collector -0.5 VDC
63.5 VOC
-63.9 VDC
63.9 VDC
0.1 VDC
0.1 VOC
-63.9 VOC
-0.1 VDC
~0.1 VDC
0.4 VOC
0.1 VOC
-9.1 VOC
9.0 VOC
0.7 VOC
1.7 VDC
7.5 VOC
0.1 VOC
8.0 VOC
7.5 VDC
0.3 VDC
0.3 VOC
0.5 VDC
0.5 VOC
3.0 VOC Q 702
Q 703
Q 704
Q 705
Q 706
VW collector
collector
collector
collector
base
emitter
collector
base
emitter -0.8 VOC
63.5 VDC
-63.5 VOC
63.9 VOC
0.1 VDC
0.1 VDC
-63.9 VOC
-0.1 VOC
-0.1 VDC
VOC
voc
VOC
voc
VDC
voc
voc
voc SMHOoOOLHY N&O Os NS Oownnn
UNIVERSAL SOUND BOARD CIRCUIT DESCRIPTION
The Universal Sound Board operates under control of stored program data. These digital signals are converted to an analog signal (clocked sinusoidal wave), by the use of digital-to-analog converters, summed together and fed through an output amplifier. This final output may or may not be filtered. The sound board is sub-divided into three independent and identical sound blocks or envelops (CTCO, CTC] and CTC2). Refer to the table for IC assignments for the individual blocks. A sound block consists of (a) Programmable Interval Timer, an 8253; (b) a decode multiplexer which provides a WR signal for the D-to-A converters (74LS139's); (c) three independent and identical output channels (AD7524's);
- a filtering network, made up of analog switches (4053's) and a controller IC (74LS74's); and (e) a summing amplifier (TLO82's). Under program control the sound data is simultaneously sent to the timing IC's (8253's) and the D-to-A converters. The Programmable timer generates three sine wave outputs (OUT 0, 1, 2) which provides a timing signal for the D-to-A converters and the filter network. Simultaneously, the decoder multiplexers (74LS139's) under program control develops a WR signal that allows the program data, already available, to be written into the D-to-A converters. The output of the D-to-A converters (pin 1) are fed into the op-amps (TLO82's) which provides a sine wave output that varies between plus and minus two volts. The ouptut of these three channels are then sunned together by the op amps. The resulting output can then either be sent directly to the output amp or be re-routed and fed through the filtering network. The filtering network is under control of the signal switch(s) which is developed by the controller IC's (74LS74). When the signal switch equals one (a HI), the filtering network is on, and the output is being filtered. The opposite is true when the signal switch equals zero (a LO). Circuit configuration in the analog switches are: xy to y for one (HI), and xy to x for zero (LO). The switch signal also allows development of a filtered or un-filtered noise output. ,
Finally, the analog sound output of the filters is then routed to the output amplifier TLO82 (U1).
STAR_TREK SOUNDS 11/23/82 2 ms. clock rate (USB jumper P2 set at pin #5)
uses SBO, channel A, switch=1 Enterprise Warp Drive .... . . . uses SBO, channels A, B and C, switch=1 Enterprise Impulse Drive ....
Enterprise Phaser. ...... . . uses SB1, channels A, B and C, switch=0 Enterprise Photon Torpedo . + + + « uses SBO, channels A, B and C, switch=1 Enterprise Red Alert ...... . uses SB1, channel B, switch=0 Enterprise Targeting ..... . . uses SB2, channels A and B, switch=0 Enterprise Command Deny... . . . uses SBl, channel A, switch=0 Enterprise Shields Hit .... . . uses $B2, channel B, switch=0 Enterprise Hit ......... . uses SB2, channels A, B and C, switch=0 Enterprise Explosion ..... . . uses SB], channels A, B and C, switch=0, SB2, channel C, switch=0 Enterprise Introduction... . . . uses SBO, $B1 and SB2, channels A and B, switch=1 Klingon Photon Torpedo ..... . uses SB , channel B, switch=0 Klingon Explosion. ...... . . uses SBI, channels A, B and C, switch=0, SB2, channel C, switch=0 Klingon Introduction ..... .. uses SBO, SBl and SB’, channels A and B, switch=1 Star Base Dock ......... . uses SBO, channels A and B, switch=1 Star Base Hit. ......... . uses SB2, channels A, B and C, switch=0
Star Base Damage Critical . . . . . uses SB1, channel A, switch=0 Star Base Explosion. ..... . . uses SBl, channels A, B and C, switch=0, SB2, channel C, switch=0 Star Base Bonus Used ..... . . uses SBI, channel A, switch=0 Star Base Bonus Unused .... . . uses SBl, channel A, switch=0 Star Base Introduction ..... . uses SBO, SB1 and SB2, channels A and B, switch=1
Saucer Warp Suck ........ . uses SB2, channel B, switch=0 Saucer Exit. .......... . uses SB2, channel B, switch=0 Saucer Warp Suck/Exit Off . .. . . uses no Channels Nomad Moving ........ =... uses SB2, channel B, switch=0 Nomad Stationary ........ . uses SB2, channel B, switch=0 Nomad Movement /Stationary Off . . . uses no channels Player Change... ...... . . uses SBO, channel B, switch=0 Game End . 1... 2... 4s « « USES SB2, channel B, switch=0 High Score Music ....... . . uses SBO and SBI, channels A and B, switch=1, SB2, channel A, switch=] Coin Drop Music. ....... . . uses SBO and SB1, channels A and B, switch=1, SB2, chanel A, switch=1
P. I. Timer (8253's) Channel A
Channel B
Channel C
Filter Network
Controller IC for
Filter Network
Decoder Multiplexer Summing Amp UNIVERSAL SOUND BOARD
SOUND BLOCK IC ASSIGNMENTS
U4)
u26, U19
u25, U18 u24, U17, U7 us
U38
u10
U6 Sound Block 0 Sound Block }
u42
ul2, U3 u13, U4 ul4, U5, U16 Ul6, U9, U7, U15
p/o U2 p/o U1]
ug Sound Block 2
u43
u27, U20
uz8, U21 U9, U22, U3] U30, U23, U3]
p/o U2 p/o UII
U23
TOP ASSEMBLY STAR TREK DRAWING NUMBER 700-0109
| ITEM NO. | PART NO. | QTY REQD. | DESCRIPTION |
| 1 | 140-0021-00 | 1 | Cover Junction Box |
| 2 | 140-0111-00 | 1 | Cabinet Model 104 |
| 4 | 220-0178-00 | 2 | Draw Catch |
| 5 | 250-0568-01 | 1 | Logo Panel Molding |
| 6 | 250-0568-02 | 1 | Logo Panel Molding |
| 7 | 253-0228-00 | 1 | Clear Monitor Panel |
| 8 | 253-0238-00 | 1 | Plastic Bag 3.00 x 4.00 Vinyl |
| 9 | 253-0254-00 | 1 | CRT Mask, 19" |
| 10 | 253-0281-00 | 1 | Envelope, 12 x 15, Clear |
| 11 | 253-0285-00 | 1 | Horizontal Plastic CRT Bezel |
| 12 | 253-0291-00 | 1 | Logo Panel |
| 14 | 260-0001-00 | 1 | Axial Cooling Fan |
| 15 | 280-0005-00 | 40 | Cable Tie |
| V7 | 280-0475-00 | 60 | Staple |
| 18 | 280-0495-00 | 1 | Compression Spring |
| 19 | 281-0045-28 | 2 | Screw, 10-16 x 1.75 PN HD Phil Sheet Metal |
Type AB
| 20 | 281-0045-12 | 7 | Screw, 10-16 x .750 PN HD Phil Sheet Metal |
Type AB
| 21 | 281-0134-12 | 8 | Screw, 8-18 x .750 PN HD Phil Sheet Metal |
Type AB Black
| 22 | 281-0185-24 | 4 | Screw, 10-16 x 1.50, 82° Flat HD Phil |
Sheet Metal Type AB Black
| 23 | 281-0042-32 | 4 | Screw, 6-20 x 2.00 PN HD Phil Sheet Metal |
Type AB
| 24 | 282-0017-24 | 4 | Bolt, 3-20 x 1.50 Hex HD Machine THD |
| 25 | 282-0019-32 | 1 | Bolt, 3/8-16 x 2.00 Hex HD Machine THD |
| 26 | 283-0060-18 | 4 | Washer, #6 Flat, Steel |
TOP ASSEMBLY STAR TREK DRAWING NUMBER 700-0109
Washer, #10 Flat, Steel
Washer, #3 Flat, Steel Washer, #3/8 Flat, Steel
Washer, #10 Lock, Split, Steel Washer, #3 Lock, Split, Steel Washer, #3/8 Lock, Split, Steel Nut, 10-24 Wing, Steel, Machine
Cable Clamp .250 Nylon
Decal, Caution 115V
Decal, Self-Test Instructions
Decal, Toll-Free Numbers
Decal, Dip Switch Settings
Decal, FCC Compliance Decal, Original Game Seal
Assy AC Junction Box
| ITEM NO. | PART NO. | QTY REQD. | DESCRIPTION |
| 27 | 283-0060-25 | 3 | |
| 28 | 283-0060-34 | 4 | |
| 29 | 283-0060-40 | 1 | |
| 30 | 283-0061-06 | 7 | |
| 31 | 283-0061-08 | 4 | |
| 32 | 283-0061-10 | 1 | |
| 33 | 283-0071-14 | 1 | |
| 35 | 289-0002-02 | 1 | |
| 36 | 320-0020-00 | 4" | Sealant Foam |
| 38 | 320-0053-00 | -66' | Duct Tape |
| 39 | 420-0030-00 | 1 | |
| 40 | 420-0656-00 | 1 | |
| 41 | 420-0713-00 | Advertising Pouch | |
| 42 | 420-0793-00 | 1 | |
| 43 | 420-0855-00 | Star Trek Manual | |
| 44 | 420-0856-00 | Interior Graphic | |
| 45 | 420-0857-00 | Left Side Graphic | |
| 46 | 420-0858-00 | 1 | Right Side Graphic |
| 47 | 420-0860-00 | 1 | |
| 48 | 420-0861-00 | Box Decal | |
| 49 | 420-0864-00 | Light Baffle | |
| 51 | 420-0912-00 | 1 |
52 420-0913-04
| 53 | 420-0917-00 | Decal, FCC Warning | |
| 54 | 420-0936-00 | 1 | Decal, Trademark |
| 56 | 800-0145-01 | 1 | |
| 57 | 800-0322-00 | 1 | Assy Fan Cord |
TOP ASSEMBLY STAR TREK DRAWING NUMBER 700-0109
| ITEM NO. | PART NO. | QTY REQD. | DESCRIPTION |
| 58 | 800-0375-00 | 1 | Assy X-Y Monitor |
| 59 | 800-0415-02 | 1 | Assy Light and Speaker |
| 61 | 800-3294-02 | 1 | Assy Coin System |
| 62 | 800-3302-00 | 1 | Assy Control Panel |
| 63 | 800-3304-00 | 1 | Assy Component Shelf |
| 64 | 800-3335-00 | 1 | Assy Coin System Interface Harness |
| 65 | 800-3336-00 | 1 | Assy Control Panel Interface Harness |
| 66 | 800-3341-00 | 1 | Assy Video X-Y Interface Harness |
| 67 | 800-0255-00 | 1 | Assy AC Monitor Harness |
Top Assembly 700-0109
\ (4)
(45) a>
(:2)
a s ot®2 © ©
(1) [oe ©
- =
© ON (38)
700-0109
Top Assembly
\AALIZIZIILLIRTTIENSSSSSSSSSNSSSSSSSSSSSSS SSSI, WLLL LLL ORL LLL LLL YY Ay an
SJ i | a
ZESSSSSSSSONN \—_PZZZZ77P 4 g ee a 4 NNAANANAAAAAA AAA AANA AANANAAAAAAANAAANANANARANNARANAARAAND
SSSSSHS SH HH HHH HS ISS SS Yj KAUAI 2!
SECTION A-A
700-0109
Top Assembly
Top Assembly 700-0109
SECTION B -B
A.C. JUNCTION BOX ASSEMBLY
A.C. JUNCTION BOX ASSEMBLY
A.C. JUNCTION BOX ASSEMBLY
ITEM
NO. PART_NO.
140-0020
211-0165
211-0164
280-0361
270-0001
280-0007
280-0362
420-0013
510-0013
514-0001
514-0005
600-0001
600-0079
280-0005
218-0002- 10 283-002 2-00 284-0042-00
281-0004-12
283-0024-00
284-0044-00
284-0007-00
283-0025-00
282-0005-28
310-0016-16 QTY REQD. 00-01
1 1
2 2
4 4
1 1
1 1
1 1
4 4
1 os
1 1
1 i:
1 1
1 1
FT. 2 Ft.
2 2
2 2
2 2
2 2
1 1
2 2
1 1 DRAWING NUMBER 800-0145-00
DRAWING NUMBER 800-0145-01
DRAWING NUMBER 800-0145-02
DESCRIPTION
Junction Box Metal
Conn Quick Fem Fully Insl. .250 x .032 (AWG 18-22) Conn Quick Fem Fully Insl. .187 x .020 (AWG 18-22)
Bushing S/Rel AC Cord
Filter EMI
Bushing S/Rel 1/2
Electric Crimp Sleeve AWG 24-18 Decal 2 Amp Fuse
Switch SPDT Cherry Fuse 2 Amp 250V S.B.
Holder Fuse
Cord Line 3 Cond.
Cord Line Zip Cable Tie
SCR PN HD Phil #6-32 x .625 Mach
Nut Hex HD #6-32 Mach
Washer Lock Int. Tooth #6
SCR PN HD Phil #8-32 x .750 Mach
Nut Hex HD #8-32 Mach
Washer Lock Int. Tooth #8
Washer Flat STD 0.D. #1/4
Nut Hex HD #10-24 Mach
Bolt Carriage #10-24 x 1.750 Mach Insul TGB .187 ID
A.C. JUNCTION BOX ASSEMBLY-Cont inued DRAWING NUMBER 800-0145-00 A.C. JUNCTION BOX ASSEMBLY-Continued DRAWING NUMBER 80U-0145-01 A.C. JUNCTION BOX ASSEMBL Y-Cont inued DRAWING NUMBER 800-0145-02
ITEM QTY REQD.
| ‘NO. | PART_NO. | -00 | -01 | -02 | DESCRIPTION |
| 28 | 284-0004-00 | 2 | @ | 2 | Washer Flat STD 0.D. #8 |
| 29 | 420-0597 | - | - | 1 | Decal 1 Amp Fuse |
| 30 | 420-0634 | - | 1 | - | Decal 5 Amp Fuse |
| 31 | 514-0051 | - | - | 1 | Fuse 1 Amp 250V |
| 32 | 514-0053 | - | 1 | - | Fuse 5 Amp S.B. |
AC Junction Box Assembly 800-0145
TRANSFORMER EMI ASSEMBLY DRAWING NUMBER 800-0190
Qry ITEM NO. PART_NO. REQD.. DESCRIPTION
| 1 | 560-0055 | 1 | G-80 Power Supply Transformer |
| 2 | 212-0016 | 1 | Connector, Female, 10 Pin |
| 3 | 211-0005 | 9 | Connector Crimp |
| 4 | 211-0045 | 1 | Connector Plug Amp, 6 Pin |
| 5 | 211-0042 | 6 | Connector Socket |
| 6 | 211-0043 | 2 | Connector Plug Amp, 2 Pin |
| 7 | 600-0079 | 1 foot | Zip Cord |
| 8 | 280-0005 | 4 | Cable Tie |
| 9 | 0.5 feet | Electric Strand Wire, Black, AWG 18 | |
| 10 | 280-0359 | 3 | Electric Crimp Sleeve |
| | | 211-0077 | 4 | Connector Terminal Socket, 20-14 AWG |
EMI Transformer Assembly 800-0190
}+——— 15.00 Bal]
DETAIL_A
VOLUME CONTROL BLOCK ASSEMBLY DRAWING NUMBER 800-3282
| ITEM NO. | PART NO. | QTY REQD. | DESCRIPTION | REF DES |
=00 -01 -02
| 1 | 240-0001-00 | 1 1 1 Volume Control Knob |
| 4 | 250-0569-00 | 1 1 - Bracket Volume Control Block |
| 3 | 289-0003-14 | 4 4 4 Eyelet Rolled FLG HD |
| 4 | 420-0829-00 | 1 1 - Decal, E-Z Adjust Cont |
| 5 | 475-0007-00 | 1 - 1. Pot 10K Car Panel Mount |
| 6 | 510-0051-00 | 2 2 2 Switch, Pushbutton Slide |
| 7 | 420-0395-00 | - - 1 Decal, Serv SW/Vol Cont |
| 8 | 211-0041-00 | 5 5 6 Conn Pin Amp |
| 9 | 211-0182-00 | 4 4 5 Terminal .110 x .020 22-18 AWG |
Quick, Fully Insul. Female
| 10 | 280-0005-00 | 4 4 3. Cable Tie |
1l 310-0041-02 .08' - .08' Tubing .125 ID Clr Polyolefin Shrink
| 12 | 470-0101-00 | 1 - 1. Resistor 100 ohm 3W, 5% |
13 600-0029-00 1.38' 1.38' - CA 2 CNDCT Sheild 22 AWG
14 600-0092-47 1.46' 1.46'.75'Wire 22 AWG Violet
15 600-0092-48 1.54' 1.54' - Wire 22 AWG Gray
16 600-0092-50 1.62'1.62'1.116Wire 22 AWG Black
| 17 | 475-0034-00 | - 1 = Pot 200 ohm Car Panel Mount | |
| 18 | 600-0013-00 | - - 3.1' CA 1 Condition Sheild | |
| 19 | 600-0092-42 | - - .75' Wire 22 AWG Red | |
| 20 | 600-0092-44 | - - .83' Wire 22 AWG Yellow | |
| 21 | 211-0005-00 | - - 2. Conn Crimp Lock | p24 |
| 22 | 211-0046-00 | - - 1. Conn Cap Amp 6 Pin | Pg |
| 23 | 212-0005-00 | - + 1. Conn Female Black 4 Pin | |
| 24 | 250-0569-01 | - - 1 Bracket Volume Control Block | |
| 25 | 211-0166-00 | - - 1 Conn Ring Lug #10 | |
| 26 | 283-0063-04 | - = 1. Washer, #10 Lock, Ext Tooth Star | |
| 27 | 283-0070-03 | - | 1 Nut, Nylon, Self Locking #10 |
| 28 | 281-0005-06 | - oe 1 Screw, #10 x .375 PN HD Phil Machine |
Volume Control! Block Assembly 800-3282-00
4PL
Volume Control Block Assembly 800-3282-0
Volume Control Block Assembly 800-3282-01
- ov
SHIELD WIRE
VOLUME
SERVICE
LIGHT AND SPEAKER ASSEMBLY DRAWING NUMBER 800-0415
Speaker, 6 x 9, 10W Panel, Speaker and Light Panel, Speaker and Light Panel, Speaker and Light Screw, 8-32 x 1.75 LG OVH Phil Machine
Bolt 10-24 x 1.25 LG CRG HD Machine
Nut 8-32 Hex, Machine THD Nut 10-24 Hex, Machine THD
Washer, #8 Flat, Steel
Washer, #10 Flat, Steel
Washer, #8 Lock, Split, Steel Washer, #10 Lock, Split, Steel
Fluorescent Lamp Assy Fluorescent Lamp Assy Speaker Harness Assy Speaker Harness Assy Fluorescent Lamp Assy
| ITEM NO. | PART NO. | QTY REQD. | DESCRIPTION |
=00 -O1 -02
| 1 | 130-0002-00 | 1 1 1 Speaker, Cover |
| 2 | 130-0020-00 | 1 11 |
| 3 | 252-0213-01 | - - 1 |
| 4 | 252-0213-00 | lo- - |
| 5 | 252-0242-00 | - 1 - |
| 6 | 281-0014-28 | 4 4 4 |
THD Black
| 7 | 282-0005-20 | 2 2 2 |
THD BLACK
| 8 | 283-0072-13 | 4 4 4 |
| 9 | 283-0072-15 | 2 2 2 |
| 10 | 283-0060-21 | 4 4 4 |
| 11 | 283-0060-24 | 2 2 2 |
| 12 | 283-0061-05 | 4 4 4 |
| 13 | 283-0061-06 | 2 2 2 |
| 15 | 390-0019-00 | 1 1. 1- Lamp Fluorescent |
| 16 | 800-0147-02 | - 1 - |
| V7 | 800-0147-03 | lo- - |
| 18 | 800-0371-00 | to- - |
| 19 | 800-0412-00 | - 1 - |
| 20 | 800-0147-05 | - - 1 |
| 21 | 800-0403-01 | - - 1 |
Speaker Harness Assy
Light and Speaker Assembly 800-0415
FOR -00 ASSY (4) FOR -00 ASSY FOR -01 ASSY (s) FOR -01 ASSY FOR -02 ASSY G) FOR -02 ASSY BBPBBOA®
a
ae 1 OWS (iia é S
- (ey 00 ASSY Gd
- 01 ASSY a) (iz
- 02 ASSY Yw £8 we
FLUORESCENT LAMP 2 ASSEMBLY DRAWING NUMBER 800-0147
Conn Crimp Ring #10
Bushing Strain Rel, AC Cord Elec Crimp Sleeve 24-18 AWG
Screw, #6-32 x .375 PAN HD,
Washer #6 Flat, Steel
Fluorescent Lamp Fixt. 18"
Fluorescent Lamp Fixt. 18"UL
| ITEM NO. | PART NO. | QTY REQD. | DESCRIPTION |
200-01 -02 -03 ~04 -05
| 1 | 211-0041-00 | 2 2 2 2 2 2. Conn Pin Amp | |
| 2 | 211-0044-00 | 1 1 1 1 1 1 Conn Cap Amp 2 Pin | |
| 4 | 211-0166-00 | 1 - | - oe |
| 6 | 280-0361-00 | - 1 1 1 1 | |
| 7 | 280-0362-00 | - 2 2 2 2 2 | |
| 9 | 281-0002-06 | 1 1 1 1 1 1 |
Phil, Mach THD
| 14 | 283-0060-19 | - 1 1 1 1 1 |
| 17 | 390-0083-00 | 1 - oe ee - |
| 18 | 390-0117-00 | - 1 1 1 1 1 |
| 23 | 600-0079-00 | - 5.9'7.6'4.0'4.4'6.75' |
CA 2 Cond Zip Cord
Flourescent Lamp 2 Assembly 800-0147
COIN SYSTEM ASSEMBLY DRAWING NUMBER 800-3294
| ITEM NO. | PART NO. | QTY REQD. | DESCRIPTION |
-00°-01 -02 1 220-0212-00 “I “I ~T Lock Panel 4-Way
| 2 | 220-0265-00 | 1 1 - Coin Mech - Double Frame, Mini-Door |
| 3 | 285-0001-04 | 2 2 2 = Rivet, .125 Dia x .250 LG, MDRL Pull, AL |
| 4 | 800-3282-00 | 1 - = Volume Control Block Assy |
| 5 | 800-3282-01 | - 1 - Volume Control Block Assy |
| 6 | 800-3282-02 | - oe 1 Volume Control Block Assy |
| 7 | 220-0265-01 | - - 1. Coin Mech - Double Frame, Mini-Door |
Coin System Assembly 800-3294
-00 ASSY
-Ol ASSY
-02 ASSY
P/O ITEM 2 (-00 8-01 ASSY) ITEM 7 (-02 ASSY)
REAR VIEW OF COIN ENCLOSURE
FRONT VIEW
CONTROL PANEL ASSEMBLY DRAWING NUMBER 800-3302
Button, Plunger, Red Button, Plunger, Black Button, Plunger, Yellow Button, Plunger, Orange Button, Plunger, Blue
Control Panel Graphic
din. - 13 Hex Pal Nut Spacer .140 ID x .250 OD X .250 L& Nylon
Screw 6-32 x .625 LG PNH Phil, Machine THD
Bolt 10-24 x .750 LG CRG HD, Machine THD
Nut 10-24 Hex, Self Locking, Machine THD
Washer #6 Flat, Steel
Washer #10 Flat, Steel Washer #10 Lock, Split, Steel
Pin .099 Dia x .750 LG, Roll, Spring
Switch, Push Button, Metal, Panel
Single Player Control Panel Interface Assy
Rotary Control Assy
| ITEM NO. | PART NO. | QTY REQD. | DESCRIPTION |
| 1 | 240-0006-00 | 1 | |
| 2 | 240-0007-00 | 2 | |
| 3 | 240-0009-00 | 1 | |
| 4 | 240-0109-00 | 1 | |
| 5 | 240-0111-00 | 1 | |
| 7 | 250-0565-00 | 1 | Control Knob |
| 8 | 250-0616-00 | 1 | Control Panel |
| 9 | 253-0312-00 | 1 | |
| ll | 280-0005-00 | 8 | Cable Tie |
| 12 | 280-0327-00 | 2 | Base Tie Wrap |
| 13 | 280-0329-00 | 6 | |
| 14 | 280-0465-00 | 4 | |
| 16 | 281-0002-10 | 4 | |
| 17 | 282-0005-12 | 4 |
Black
| 19 | 283-0070-03 | 4 |
| 20 | 283-0060-18 | 4 |
| 21 | 283-0060-24 | 4 |
| 22 | 283-0061-06 | 4 |
| 24 | 289-0001-12 | 1 |
Steel
| 26 | 510-0064-00 | 6 |
| 28 | 800-0374-00 | 1 |
| 29 | 800-0390-00 | 1 |
| 30 | 800-3303-00 | 1 |
Control Panel Harness Assy
Control Panel Assembly 800-3302
9.50 tae — 3.80 at fean.3) [es.9) BEAR VIEW 79
ROTARY CONTROL ASSEMBLY
ITEM_NO.
Pwn PART _NO.
281-0031-04
284-0011-05
800-0382 800-0383 Qry
REQD.
-- NN DRAWING NUMBER 800-0390
DESCRIPTION
Scr #4-40 X 1/4" PN HD Thd Forming
Wshr #4 Fl, SM OD, Stl Rotary Interface Assy Rotary Bracket Assy
800-0390
Rotary Control Assembly
SINGLE PLAYER CONTROL PANEL INTERFACE ASSEMBLY DRAWING NUMBER 800-0374
qTy
| ITEM NO. PART NO. | REQD.. | DESCRIPTION |
REF DES.
| 1 | 150-0088 | 1 | Cap E 10 uf 25V RDL | C3 |
| 2 | 151-0058 | 2 | Cap .01] uf 16V AX | cl, c2 |
| 3 | 151-0059 | 1 | Cap .001 16V AX | C4 |
| 4 | 170-0258 | 1 | PC Board | |
| 5 | 212-0024 | 1 | Conn 12 Pin M RTA PLRZD | P30 |
| 6 | 212-0156 | 1 | Conn Header 15 Pin | P10 |
| 7 | 314-0055 | 2 | IC 74LS244 | U2, U3 |
| 8 | 314-0062 | 1 | IC 74874 | Vis} |
| 9 | 314-0075 | 1 | IC 74LS39 | Ul |
| 10 | 314-0085 | 1 | IC 74LS14 | U4 |
| 11 | 471-0102 | 3 | Res 1K Ohm 1/2W 5% | R1-R3 |
Single Player Control Panel Interface Assembly 800-0374
ROTARY ASSEMBLY INTERFACE DRAWING NUMBER 800-0382
QTY
| ITEM NO. PART NO. | REQD. | DESCRIPTION | REF DES. | |
| 1 | 170-0160 | 1 | PC Board | |
| 2 | 212-0081 | 1 | Conn M 4 Pin RTA PLRZD | Pl |
| 3 | 285-0001 -04 | 4 | Rivet .125 Dia X .25 Lg | |
| 4 | 370-0006 | 2 | Opto Electric Encoder XSTR | DS], DS2 |
| 5 | 470-0101 | 1 | Res 100 Ohm 1/4W 5% | R1 |
Rotary Interface Assembly 800-0382
“TOP
BOTTOM
ORIENTATION LOCATION NUMBER MARK
HZIAZ NOTCH FACING BOTTOM
K-2183 K-Z133A FACING TOP
COLOR MONITOR ASSEMBLY
ITEM NO. PART NO. QTY REQD. DRAWING NUMBER 800-0375
DESCRIPTION
NOOR WNH 200-0025-00
211-0059-00
252-0175-00
282-0017-24
283-0060-34
283-0070-05 FoR X-Y Color Monitor, 19"
Conn Plug 3 Pin Amp
Monitor Mounting Board Hex HD Bolt, 4 - 20 x 1.500 LG Washer, Flat 4 - 1.250 LG 0.D. Fender
Nut, } - 20 Hex Self-locking, Mach THD
Color Monitor Assembly 800-0375
19" X-¥ COLOR MONITOR
PART_NO.
EHT SUPPLY ASSEMBLY
SEMI -CONDUCTORS
315-0118
481-0211 481-0207
482-0062
482-0244
482-0030
TRANSFORMERS
560-0062
560-0073
COILS
180-0010
CAPACITORS
150-0007 152-0053
151-0109
150-0015
151-0110
150-0222
150-0010
150-0221
151-0113
152-0027
RESISTORS
470-0103
460-0008
470-0154
470-0123
471-0472
471-0474
460-0016 DESCRIPTION
EHT Control Circuit
Zener Diode Rectifier 1A 1400V
Transistor 3906
Transistor MPSUQ7
Transistor 3904
Horiz. Buffer Trans.
Horiz. Output Trans.
Horiz. Delay Choke
4.7 uf 16V
0.22 uf 50V
2000 uf 50V
22 uf 16V
0.1 uf 100V
0.022 uf 100V
100 uf 16V
High Current Cap
47 uf 160V
0.047 uf 100V
10K 1/4W 5%
47K 1/4W 5%
150K 1/4W 5%
12K 1/4W 5%
4.7K 1/4W 5%
470K 1/ W 5% 1.2K 1/4W 5% DRAWING NUMBER 200-0025
RES. DES.
1c900
70903, 904 pyol
gol
qg03
T900
T901
L900
c900 c902
C903
c904
C906, 912 c907
cai
c914, 915
C916
C918
R900, 901, 906
R902
R904, 916, 934
R905, 915 R907, 938, 939
R910
R914
19" X= COLOR MONI TOR-Continued
PART_NO. DESCRIPTION
EHT SUPPLY ASSEMBLY CONT'D
RESISTORS
475-0043
475-0044
470-0271
470-0471
471-0240
470-0330
470-0680
462-0001
464-0114
470-0333
470-0274
471-0475
471-0331
472-0470
470-0562
EHT SUPPLY ASSEMBLY KIT
482-0242
475-0035
EHT REGULATOR ASSEMBLY
SEMI - CONDUCTORS
482-0268
482-0269
481-0204 CAPACI TORS 152-0149
151-0108
472-0223
471-0683
472-0273
471-0473 200 Ohms Control
2k Control
270 Ohm 1/4W 5%
470 Ohm 1/4W 5% 24 Ohm 1/2W 5%
33 Ohm 1/4W 5%
68 Ohm 1/4W 5%
68 Ohm IW 5%
470K Control
33K 1/4W 5%
270K 1/4W 5%
4.7M 1/2W 5%
330 Ohm 1/2W 10%
47 Ohm IW 5%
5.6K 1/4W 5%
PWR Transistor 5A 1400V
Focus Control
2N 6558 TIP 47 (Motorola) IN 5263
68 pf 500V 470 pf 500V 22K IW 5%
68K 1/2W 5%
27K IW 5%
47K 1/2W 5% DRAWING NUMBER 200-0025
RES. DES.
R917
R918
R923
R924
R925
R927
R930
R932
R933
R935
R936
R937
R940
R941
R942
Q900 R922
Q320, 321, 323
Q322 20340
C330
C331
R300
R301
R302
R304
19" X-Y COLOR MONI TOR-Cont inued DRAWING NUMBER 200-0025
PART NO. DESCRIPTION
EHT REGULATOR ASSEMBLY CONT'D
RESISTORS 470-0331 330 Ohm 1/4W 5% 471-03R3 3.3 Ohm 1/2W 5% 470-0363 36K 1/4W 5% 460-0008 47K 1/4W 5% 475-0048 10K Control Pot.
DEFLECTION AMP PCB ASSEMBLY
SEMI -CONDUCTORS
315-0117 Input Amplifier IC 481-0202 Rectifier 481-0020 Rectifier 1A 200V
481-0006 Diode IN 914 481-0204 Zener Diode IN 5263B 1/2W 56V 481-0205 Zener Diode IN 5239B 1/2W 9.1V 481-0179 Zener Diode 9.1V IW 5% (Motorola)
482-0248 Transistor TIB 29B
482-0244 Transistor MPSU60 (Motorola) 482-0245 Transistor 300V 1/2A
482-0243 Transistor MPSU10 (Motorola)
CAPACTORS
150-0211 100 uf 80V 150-0212 680 uf 160V 150-0213 6800 uf 80V 150-0004 10 uf 25V 151-0046 Ceramic 0.1 uf
152-0056 0.1 uf 200V 150-0220 22 uf 250V RES. DES.
R305
R306 R307
R308
R310
1C600
0400-403
0404-407, 409,
D408, 601-605 701-705
ZD400
ZD401 20402 (1N4739)
400, 401 Q600, 700 Q601, 604, 701,
Q602, 603, 702,
c401
c402
C403, 404
c405
C407, 621, 721
c410
cai)
19" X-Y COLOR MONI TOR-Continued
PART_NO. DESCRIPTION
DEFLECTION AMP PCB ASSEMBLY CONT'D
CAPACITORS
152-0145
152-0146
152-0147
152-0023
151-0107
152-0149
152-0150 RESISTORS
478-0006
473-0330
472-0223
470-0222
474-0220
471-0822
474-0680
470-0472
470-0275
470-0155
470-0621
471-0911
470-0103
470-0182
470-0303
475-0037
470-0104
470-0242
470-0102
475-0038
470-0183 2.2 pf 500V 12 pf 500V 100 pf 10% 500V 47 pf.10% 500V 0.068 uf 200V
5.6 pf 10% 560 pf 500V 20%
Thermistor 120V 60 Ohm
33 Ohm 4W 10%
2a IW 10%
2.2K 1/4W 5%
220 Ohm 10W
8.2 1/2W 5%
680 Ohm 6W
4.7K 1/4W 5%
2.7M 1/4W 5%
1.5M 1/4W 5%
620 Ohm 1/4W 5%
910 Ohm 1/4W 5%
10K 1/4W 5%
1.8K 1/4W 5%
30K 1/4W 5%
50K Trim Pot
100K 1/4W 5%
2.4K 1/4W 5%
1K 1/4W 5%
1K Trim Pot
18K 1/4W 5% DRAWING NUMBER 200-0025
RES. DES.
C600
603, 703 C620, 720
(622, 722 C624, 724 c702
C725
R400
R401
R402
R403
R404
R405
R406
R410
R411
R412
R600
R601
R602
R603, 624, 724
R604
R605
R606
R607, 710 R608, 636, 637,
715, 736, 737 R6ll
R620, 720
19" X-¥ COLOR MONI TOR-Continued
PART NO. DESCRIPTION
DEFLECTION AMP PCB ASSEMBLY CONT'D
RESISTORS
470-0622 6.2K 1/4W 5% 470-0181 180 Ohm 1/4W 5%
470-0223 22k 1/4W 5%
470-0101 100 Ohm 1/4W 5%
471-0183 18K 1/2W 10% 470-0271 270 Ohm 1/4W 5% 471-0223 22k 1/2W 5% 472-0471 470 Ohm 2W 5% 470-0151 150 Ohm 1/4W 5% 460-0056 82 Ohm 1/4W 5% 474-0150 1.5 Ohm 10W
470-0222 2.2K 1/4W 5% 475-0039 5K Trim Pot 470-0153 15K 1/4W 5% 470-0152 1.5K 1/4W 5%
472-0391 390 Ohm 2W 5% 470-0475 4.7M Trim Pot CRT SOCKET PCB ASSEMBLY SEMI-CONDUCTOR S 482-0243 Transistor MPS ul0 (Motorola) LAMPS 390-0107 Lamp CAPACI TORS 151-0067 100 pf 500V 151-0112 0.1 uf 200V
151-0050 0.01 uf 500V 10% 151-0096 0.01 uf 1000V DRAWING NUMBER 200-0025
RES. DES.
R621, 721
R622, 625, 631, 722, 725, 731 R623, 704, 705,
R626, 629, 726,
R627, 727 R628, 728 R630, 730 R632 R633
R634
R635
R700, 701 R702
R703, 706 R714
R732
R930, 931
Q100-105
NE100-103
C100, 110, 130 C101
ci02, 111, 131 Cli2, 113
19" X-Y COLOR MONI TOR-Cont inued DRAWING NUMBER 200-0025
PART NO. DESCRIPTION RES. DES.
RESISTORS
| 470-0101 | 100 Ohm 1/4W 5% | R101, 112, 130 |
| 470-0275 | 2.7K 1/4W 5% | R102, 113, 131 |
| 462-0056 | 3.3K IW 5% | R103, 114, 132 |
| 472-0471 | 470 Ohm 1/4W 5% | R104, 115 |
| 470-0122 | 1.2K 1/4W 5% | R105, 116, 134 |
| 475-0041 | 250 Ohm Trim Pot | R106, 117 |
| 475-0042 | 2.5K Trim Pot | R107, 118, 136 |
| 471-0222 | 22k 1/2W 5% | R108, 119, 137 |
| 470-0181 | 180 Ohm 1/4W 5% | R109, 121 |
| 470-0102 | 1K 1/4W 5% | R110 |
| 471-0224 | 220K 1/2W 5% | R122 |
| 471-0102 | 1K 1/2W 5% | R123 |
| 471-0474 | 470K 1/2W 5% | R124 |
| 470-0621 | 620 Ohm 1/4W 5% | R133 |
HEAT SINK ASSEMBLY
| 482-0260 | 2N 6259 | Q605, 606, 705, |
| 260-0010 | Motor Blower Fan | Mol |
MISCELLAEOUS
| 200-0040 | CRT | vol |
| 180-0009 | Deflection Yoke | byol |
| 180-0017 | Degaussing Coil | L100 |
| 213-0019 | CRT PCB Socket | J101 |
| 280-0208 | Yoke Wedge | x |
| 800-0307 | Input Limiter PCB | xX |
| 800-0319 | Input Clamp PCB | xX |
19” X-Y Color Monitor 200-0025
a 0 ‘ti Os 3] | 3
Gal aE) SLE
i oS a ; !
A) tar Sey || | ee SF Po os ~OO0. Lh
X-Y P.C.B. COMPONENT LAYOUT
19” X-Y Color Monitor
R932
Fs
a |g scso0 hs C) ae & 3), soe wOw? lg rom, ™ 3p Os ce IS O oO” C904 R936 R933 200-0025
cae
cole
COMPONENT
50-1639-02 tss.1
On
EHT P.C.B. COMPONENT LAYOUT
COMPONENT SHELF ASSEMBLY DRAWING NUMBER 800-3304
QTy ITEM NO. PART NO. REQD.. DESCRIPTION
| 1 | 250-0458-00 | 1 | Saddle G-80 Cage |
| 2 | 25 2-0142-00 | ] | Component Shelf UP. CAB. |
| 3 | 280-0324-00 | 1 | Cable Clamp Nylon |
| 4 | 281-004 5-12 | 15 | SCR 10-12 x 3/4" PN HD Type A/AB |
| 5 | 284-0016-08 | 15 | Washer Fit #10 Small OD 1/2" |
| 6 | 284-0036-00 | 15 | Washer Lock Split #10 |
| 7 | 280-0005-00 | 5 | Cable Tie |
| 8 | 800-0190-00 | 1 | Assy XFMR EMI |
| 9 | 800-0191-00 | 1 | Assy Game Pwr Supply G-80 |
| 10 | 800-0277-00 | 1 | Assy Volume Control Block |
| 1 | 800-0 285-00 | 1 | Assy Harn Gnd Game Elec. |
| 12 | 800-0286-00 | 1 | Assy Harn Gnd Pwr Supply |
| 13 | 800-0314-00 | 1 | Assy Harn Pwr |
| 14 | 800-3305-00 | 1 | Game Elec. Assy |
| 15 | 280-0475-00 | 12 | Staple |
Component Shelf Assembly 800-3304
P24
Pio
ITEM 12 ——]
800-3304
Component Shelf Assembly
G-80 CAGE UNIVERSAL ASSEMBLY DRAWING NUMBER 800-0296
qry ITEM _NO. PART NO. REQD. DESCRIPTION
| 1 | 250-0456 | 1 | G-80 Cage Assembly |
| 2 | 250-0499 | 2 | G-80 Cage Bracket |
| 3 | 280-0343 | 1 | Split Grommet |
| 4 | 420-0560 | 1 | Test Button Decal |
| 5 | 800-0105 | 1 | 6-Slot Master Board Assembly |
| 6 | 281 -0045-06 | 6 | Pan Head Phillips Screw, Type AB, 10- |
12 x .375 Lg
| 7 | 281-0001-12 | 4 | Pan Head Phillips Machine Screw, |
#4-40 x 3/4
| 8 | 281-0001-06 | 4 | Pan Head Phillips Machine Screw, |
#4-40 x 3/8
| 9 | 284-0001-00 | 4 | Flat Washer, #4 |
800-0296
G-80 Cage Universal #2 Assembly
GAME ELECTRONICS
ITEM _NO.
ON none Wwnm
n=O © PART_NO.
420-0560-00
420-0054-00 600-0089-00 800-0161-00
800-016 3-00
800-0282-00
800-0296-00
800-0378-00 800-3 307-00
800-3306-00
800-3 270-00
800-0294-00 Qry REQD. DRAWING NUMBER 800-3305
DESCRIPTION
Decal Test Button
Decal Electronics
Cable X-Y Interface
Assy X-Y Timing PCB Assy X-Y Control PCB Assy Harn Video X-Y Intf
Assy G-80 Gage Univ CPU Master Harn Assy Assy CPU PCB Assy 2716 Prom PCB
Sound Board Assy Speech Board Assy-2732
Game Electronics
Assembly
800-3305
CPU BOARD ASSEMBLY DRAWING NUMBER 800-3307
ITEM NO. PART NO. QTY REQD. DESCRIPTION
| 800-0107-02 | 1 | CPU Board Assy |
| 316-1873-00 | 1 | IC EPROM 2716 |
| 315-0064-00 | 1 | Chip 315-0064 |
REF DES
U25
CPU BOARD ASSEMBLY DRAWING NUMBER 800-0107
Qry ITEM NO. PART NO. REQD. DESCRIPTION REF DES.
| 1 | 150-0088 | 3 | Cap — 10 uf 25V | c43, C46, C62 |
| 2 | 151-0005 | 1 | Cap CER 680 pf 50V | c50 |
| 3 | 151-0012 | 1 | Cap CER .1 uf 50V | c47 |
| 4 | 151-0020 | 1 | Cap CER 33 pf 50V | c49 |
| 5 | 151-0060 | 21 | Cap CER .1 uf 16V AX | €37-C42, C44, C48, |
C51-C61, C63, C64
| 6 | 151-0061 | 36 | Cap CER 220 pf 16V AX | C1-C36 |
| 7 | 170-0194 | 1 | PC Board | |
| 8 | 211-0008 | 4 | Conn Pin Test PT | TP1-1P4 |
| 9 | 212-0098 | 4 | Conn M 10 Pin RTA | |
| 10 | 230-0013 | 1 | XTAL 8.000 MHZ | YI |
| V1 | 314-0001 | 1 | IC NE555 | ul2 |
| 12 | 314-0015 | ] | IC 7404 | U30 |
| 13 | 314-0018 | 4 | IC 74LS00 | U6, U8, Ul4, UI9 |
| 14 | 314-0019 | 1 | IC 74LS04 | ulg |
| 15 | 314-0055 | 3 | IC 74LS244 | U34, U36, U38 |
| 16 | 314-0058 | 1 | IC 74LS08 | u13 |
| V7 | 314-0062 | "5 | IC 741874 | ul0, Ul1, UI7, U20, |
u39
| 18 | 314-0066 | 1 | IC 74LS27 | U16 |
| 19 | 314-0067 | 1 | IC 74LS30 | U37 |
| 20 | 314-0068 | 2 | IC 74LS32 | U32, U33 |
| 2] | 314-0078 | 1 | IC 74LS 2 | u23 |
| 22 | 314-0083 | 1 | IC 74LS240 | u4 |
| 23 | 314-0085 | 2 | IC 74LS14 | U7, U3] |
| 24 | 314-0087 | 1 | IC 74LS139 | Ue4 |
| 25 | 314-0093 | ] | IC 74LS374 | U3 |
| 26 | 314-0099 | 1 | IC 74LS245 | U35 |
| 27 | 314-0105 | 4 | IC 74LS253 | Ul, U2, US, U9 |
| 28 | 315-0041 | 1 | IC Z80A | u22 |
| 29 | 315-0046 | 4 | IC 2114 | U26-U29 |
CPU BOARD ASSEMBLY-Continued
ITEM NO. PART NO.
315-0050
316-0764
390-0003
471-0101
471-0102
471-0103
471-0104
471-0122
471-0220
471-0221
471-0331
477-0002
481-0001
481-0006
482-0006
482-0010
482-0014
510-0052
510-0053
213-0001
213-0002
213-0004
213-0005
510-0049
471-0472
280-0420
471-0473
151-0031 QTy REQD.
HHO Ket we HDR oO DH DH HFK DH WHO WH Bwoe HH DESCRIPTION
IC 2516 (2716) IC Prom 32x8
Led Red
Res 100 Ohm 1/2W 5%
Res 1K Ohm 1/2W 5%
Res 10K Ohm 1/2W 5%
Res 100K Ohm 1/2W 5%
Res 1.2K Ohm 1/2W 5%
Res 22 Ohm 1/2W 5%
Res 220 Ohm 1/2W 5%
Res 330 Ohm 1/2W 5%
Res Pack 15x2.2K
Diode 1N4002
Diode 1N914/1N4148 XSTR N4403
XSTR PE8050
XSTR N4401
SWITCH PIANO DIP
SW Pushbutton Side PCM
SKT 24 Pin Dual INLN
SKT 18 Pin Dual INLN
SKT 16 Pin Dual INLN
SKT 40 Pin Dual INLN
Switch 8 Pos Dip Res 4.7K Ohm 1/2W 5%
Card Ejector, Snap On Res 47K Ohm 1/2W 5%
Cap CER .22 uf 16V DRAWING NUMBER 800-0107
REF DES.
U25
u15
R5
R1, R3
R6
R7, RB, R22
R12
R14
Rz, R4, RIB
R10, R11, RI5-RzZ0
RP1-RP3
D1, D2 D4
qQ7
Ql, Qe Q3-Q6, Q8 sw
SW3
XU25
XUZ6-XUZ9
xU15
xu2T, xUz2
swe
R21
R9
C45
BIG tee =| : é I | inl inl i | | I) doe Hae to, oF if see; fey STO0 aged te I [_} Hf) Ca ug OU00f pon
o 00 00 _ or
CPU Board Assembly
800-0107
2716 PROM BOARD ASSEMBLY DRAWING NUMBER 800-3306
| ITEM _NO. | PART. NO. | QTY REQD | DESCRIPTION | REF DES |
| 1 | 800-0151-00 | 1 | Assy G-80 2716 PROM Board | |
| 2 | 316-1848-00 | IC EPROM 2716 | Ul | |
| 3 | 316-1849-00 | IC EPROM 2716 | U2 | |
| 4 | 316-1850-00 | 1 | IC EPROM 2716 | U3 |
| 5 | 316-1851-00 | IC EPROM 2716 | U4 | |
| 6 | 316-1852-00 | 1 | IC EPROM 2716 | U5 |
| 7 | 316-1853-00 | 1 | IC EPROM 2716 | U6 |
| 8 | 316-1854-00 | IC EPROM 2716 | U7 | |
| 9 | 316-1855-00 | IC EPROM 2716 | us | |
| 10 | 316-1856-00 | 1 | IC EPROM 2716 | ug |
| ll | 316-1857-00 | IC EPROM 2716 | U10 | |
| 12 | 316-1858-00 | 1 | IC EPROM 2716 | ull |
| 13 | 316-1859-00 | 1 | IC EPROM 2716 | ul2 |
| 14 | 316-1860-00 | 1 | IC EPROM 2716 | U13 |
| 15 | 316-1861-00 | 1 | IC EPROM 2716 | u14 |
| 16 | 316-1862-00 | 1 | IC EPROM 2716 | U15 |
| 17 | 316-1863-00 | 1 | IC EPROM 2716 | U16 |
| 18 | 316-1864-00 | 1 | IC EPROM 2716 | U17 |
| 19 | 316-1865-00 | 1 | IC EPROM 2716 | u18 |
| 20 | 316-1866-00 | 1 | IC EPROM 2716 | ug |
| 21 | 316-1867-00 | 1 | IC EPROM 2716 | U20 |
| 22 | 316-1868-00 | 1 | IC EPROM 2716 | u21 |
| 23 | 316-1869-00 | 1 | IC EPROM 2716 | U22 |
| 24 | 316-1870-00 | 1 | IC EPROM 2716 | u23 |
G-80 2716 EPROM BOARD ASSEMBLY
ITEM_NO.
Sean awn Fw
~ PART _NO.
151-0058
151-0060
170-0211
213-0001
314-0055
314-0058
314-0059
314-0104
314-0120
211-0008
150-0088
280-0420 Qry
REQD. DESCRIPTION
Ceramic Capacitor, .01
uf, 16V AX
Ceramic Capacitor, .1
uf, 16V AX
PC Board
24-Pin Dual Inline Socket
IC 74.8244
IC 74LS08
IC 74LS10
IC 74LS138
IC 74LS154
Test Point Connector Pin
Electrolytic Capacitor, 10 uf, 25V Card Ejector, Snap On DRAWING NUMBER 800-0151
REF DES.
Cz, C4, C6, C8, C9,
Cll, C14, C16, C18,
C21, C23, C25, C27
Cl, C3, C5, C7,
clo, Clz, C13, C15, C17, C19, Cz0, Cz2, C24, Cz6, Cz8
XU1~XU23
U25
U26-U28
u29
U30
ued
TP1-TP3
C29
EPROM Board Assembly
800-0151
AK
; Ijico lo ee Hee Ll rT oh yo o'S i oo I yoo
X-Y TIMING ASSEMBLY
ITEM NO. PART NO.
1 151-0005
2 151-0058
3 170-0218
4 211-0008
5 212-0101
6 213-0001
7 213-0004
8 213-0010
9 230-0009
10 280-0420
a] 313-0004
12 313-0044
13 314-0018
14 314-0019
15 314-0040
16 314-0046
7 314-0055
18 314-0058
19 314-0062
20 314-0070
21 314-0073
22 314-0074
23 314-0076
24 314-0078
25 314-0093
26 314-0097
27 314-0101
28 314-0108
29 314-0120
30 314-0135 Qry
REQD.
~ as
An wrt nw ennnan nwa a
a ee DESCRIPTION
Cap CER 680 pf 50V
Cap .01 uf 16V AX
PC Board
Conn Pin Test PT
Conn 4 Pin M RTA
SKT 24 Pin Dual INLN
SKT 16 Pin Dual INLN
SKT 8 Pin Dual INLN
Xtal 15.46848
Card Ejector IC LM741EN Dip
IC AD561
IC 74LS00
IC 74LS04
IC 74LS125
Ic 74LS04
IC 74.8244
IC 74LS08
IC 74.874
IC 74LS86
IC 74LS175
IC 74LS191
IC 74LS157
IC 74Ls02
IC 74LS374
IC 74LS161
IC 74LS283
IC 74LS107
IC 74LS154
Ic 74LS1] DRAWING NUMBER 800-0161
REF DES.
c7
C1-C3, C6, C8-C28
TPI
XP1, XU39, XU5O
XU1, XU4
XU2, XU3
Yl
U2, U3
ul, U4 u28
U30, U40 u27
ul4
U54, U57, U58 U13, U2]
U25, U26, U4z, U43,
u52
u29
U35-U38
U15-U20
U5-U10
u53
U48, U49, U55, US6
U31-U34, U41, U51 U44-U47
Ul1, U22-U24
u50
ul2
X-Y TIMING ASSEMBL Y-Cont inued
ITEM _NO. PART NO.
315-0019
471-0202
471-0331
471-0392
475-0024
151-0008
150-0088
151-0042
481-0006
151-0002 Qry
REQD.
NNYHKHNYDANNYNANNH KY = DESCRIPTION
IC 2708
Res 2K Ohm 1/2W 5%
Res 330 Ohm 1/2W 5% Res 3.9K Ohm 1/2W 5%
Pot 1K 10 Turn
Cap CER .001 uf 50V
Cap E 10 uf 25V RDL
Cap, Cer 470 pf 50V
1N914 Diode
Cap CER 100 pf 50V DRAWING NUMBER 800-0161
REF DES.
u39
R2, R4
R7, RB RI, R5
R3, RO c29, C30
ca, C5
DI, D2
C32, C33
800-0161
X-Y Timing Board Assembly
_ L col! Uloaag SOUL 0000 foic ‘“aooggt r il
X-Y CONTROL ASSEMBLY
ITEM NO. PART NO.
1 150-0088
2 151-0002
3 151-0058 4 170-0219
5 212-0101
6 213-0001
7 280-0330
8 314-0018
9 314-0019
10 314-0040 a 314-0055
12 314-0058
13 314-0059
14 314-0060
15 314-0062
16 314-0067
7 314-0068
18 314-0074
19 314-0075
20 314-0078
21 314-0087
22 314-0093
23 314-0097
24 314-0099
25 314-0101
26 314-0108
27 314-0127
28 314-0128
29 314-0137
30 315-0046 Qry REQD.
No won oe Hs
On He eB Be annewnn wn owen a DESCRIPTION
Cap — 10 uf 25V
Cap CER 100 pf 50V
Cap CER .01 uf 16Y AX PC Board
Conn 4 Pin M RTA
SKT 24 Pin Dual INLN
Card Ejector
Ic 74LS00
IC 74LS04
IC 74L8125
IC 74LS244
IC 74LS08
IC 74LS10
IC 74LS20
IC 74LS74
IC 74LS30
IC 74LS32
IC 74LS191
IC 74LS393
IC 74Ls02
IC 74LS139
IC 7418374
IC 74LS161
IC 74LS245
IC 74LS283
IC 74LS107
IC 74LS164
IC 74LS95
IC 74LS09
IC 2114 DRAWING NUMBER 800-0163
REF DES.
C23
C14
C1-C13, C15-C22
XP]
u4o
U9, U32, Ud2
u39
U20, U21, 135, U36,
u48, U49, U54
U37
ul8, U4) u50
ul9, U51
ua7
U4, U38 U15-U17
u22
u23
u46
u2, U13
Ul0-U12, U34, U52
ul4
u33
U53
U3
U6, U7, U44, U45 ul, US U24-U31
X-Y CONTROL ASSEMBLY-Cont inued DRAWING NUMBER 800-0163
Qry ITEM NO. PART NO. REQD. DESCRIPTION REF DES.
| 31 | 315-0072 | 2 | IC AM25LS14 | U8, U43 |
| 32 | 471-0123 | 3 | Res 12K Ohm 1/2W 5% | R1, R3, R5 |
| 33 | 471-0472 | 1 | Res 4.7K Ohm 1/2W 5% | R7 |
| 34 | 471-0622 | 3 | Res 6.2K Ohm 1/2W 5% | R2, R4, R6 |
| 35 | 481-0006 | 6 | Diode 1N914/1N4148 | D1-D6 |
| 36 | 212-0002 | 8 | Socket 18 Pin | XU24-XU31 |
| 37 | 471-0471 | 1 | Res 470 Ohm 1/2W 5% | R8 |
| 38 | 471-0103 | 1 | Res 10K Ohm 1/2W 5% | RQ |
| 39 | 471-0332 | 1 | Res 3.3K Ohm 1/2W 5% | R11 |
| 40 | 471-0512 | 1 | Res 5.1K Ohm 1/2W 5% | R10 |
| 41 | 482-0006 | 1 | XSTR 2N4403 | qi |
| 42 | 482-0014 | 1 | XSTR 2N4401 | Q2 |
800-0163
X-Y Control Board Assembly
aa) pO
fom a i—l9
Ae
jg mS | "i
UNIVERSAL SOUND BOARD ASSEMBLY
ITEM_NO.
u PART_NO.
150-0087
150-0090
150-0135
151-0002
151-0021
151-0060
151-0011
152-0085
152-0144 170-0259
212-0081
213-0001
213-0022
213-0005
230-0037
280-0420
313-0037
313-0038
314-0018
314-0055
314-0060
314-0062
314-0067 QTY
REQD.
won ss nny - Ho
en DESCRIPTION
Cap-E 4.7 f 25V ROL
Cap-E 33 f 25V RDL Cap-E 1 f 25V RDL
Cap-CER 100 pf 50V
Cap-CER 20 pf 50V
Cap .1 f 16V AX
Cap-F .15 f 50V Cap-F .01 f SOV
Cap-F .082 f 50V PC Board
Conn 4 Pin M RTG PLZD
Skt 24 Pin Dual INLN
Skt 18 Pin Dual INLN
Skt 40 Pin Dual INLN
XTAL 6.0 MHz
Card Ejector Snap On IC TLO81
IC TLO82
Ic 74LS00
IC 74LS244
IC 74LS20
IC 74LS74
IC 74LS30 DRAWING NUMBER 800-0377
REF DES.
cl, C4
c60
C14, C15, C33-C36, c54
C6-C8, C19-C24
c41, C42 C3, C5, C10-Cl2,
C18, C26-C31, (37-C40, C43-C50, (57-59, C61, C62 C51, (55, C56 C9, C13, C16, C17, C25, C32
(53
Pl
XU50, XU51
xu44, xuU45
XU46
Yl
u49
Ul, U3-U6, U9,
U17-U23
U36
U55
u40
U2, U38
US9
UNIVERSAL SOUND BOARD ASSEMBL Y-Cont inued
ITEM_NO. PART NO.
314-0068
314-0075
314-0076 314-0085
314-0087
314-0099
314-0100 314-0104
314-0131
315-0035
315-0046
315-0059
315-0077
315-0079
315-0132
315-0133
470-0102
470-0103
470-0104
470-0105, 470-0124 qry
REQD.
Dw n sees Ory HH wWwnr w
wo
nN DESCRIPTION
IC 74LS32
IC 74LS393
IC 74LS157 Ic 74L814
IC 74LS139
IC 74LS245
IC 74LS273
IC 74LS138
IC 7418373
IC MM5837
Ic 2114
IC 8253
IC 8035
IC CD4053
IC AD7524
IC 2K x 8 Static RAM
Res 1K Ohm 1/4W 5%
Res 10K Ohm 1/4W 5%
Res 100K Ohm 1/4W 5%
Res 1M ohm 1/4W 5%
Res 120K Ohm 1/4W 5% DRAWING NUMBER 800-0377
REF DES.
U35, U37, U39 U32, U33
U56-U58
u48
uvlo, unl
U52, US3 u54
u34
u47
u60
u44, u45
u41-U43
u46
U7, U8, UI5, U16, U30, U3]
U12-U14, U24-U29 uU50, U51
R23, R24, R30, R33, R53, R56, R59, R63 R20-R22, R27, R40, R41, R50-R52, R57,
R58
R1, R7-R10, R12, R13, R15, R16, R18, R19, R25, R28, R29, R31, R32, R34-R36, R38, R39, R42, R43, R45, R46, R48, R49, R54, R55
R2, R11
R6
UNVERISAL SOUND BOARD ASSEMBLY-Continued
ITEM _NO. PART NO.
470-0222
470-0271
470-0272
470-0333
470-0334
470-0562
470-0332
482-0023
152-0054
152-0076
212-0158
212-0159 QTy
REQD.
—- =e see awn pnw =n DESCRIPTION
Res 2.2K Ohm 1/4W 5%
Res 270 Ohm 1/4W 5%
Res 2.7K Ohm 1/4W 5%
Res 33K Ohm 1/4W 5%
Res 330K Ohm 1/4W 5% Res 5.6K Ohm 1/4W 5%
Res 3.3K Ohm 1/4W 5%
XSTR 2N4093
Cap-F .001 f 50V
Cap-F .1 f 50V Conn Header 8 Pos
Conn Jumper DRAWING NUMBER 800-0377
REF DES.
R5, R60
R62
R64, R65 R14, R37, R44, R61
R3
R17, R26, R47
R4
Ql
c2
c52
P2
Universal Sound Board Assembly
800-0377
PeSeeoogota | stp 8 § oy ht § aa ra a 5 c1@=74 CE oo he Shs —e = — THe Sie — ‘ 8 io — ——} HS De SS fe yp Pair _ Ld, Beer IS oO __ I J — [iti if
SPEECH BOARD ASSEMBLY
ITEM NO.
Pwene PART NO.
800-0294-00
316-1607-00
316-1871-00
316-1872-00 QTY REQD.
Pepe DRAWING NUMBER 800-3308
DESCRIPTION
Assy 2732 Speech PCB IC EPROM 2716
IC 2732
IC 2732 REF DES
U7
U6
us
SPEECH BOARD ASSEMBLY DRAWING NUMBER 800-0294
QTY
ITEM NO. PART NO. REQD. DESCRIPTION
| 1 | 150-0087 | ] | Cap — 4.7 uf 25V |
| 2 | 150-0088 | 5 | Cap — 10 uf 25V |
| 3 | 151-0021 | 2 | Cap Cer 20 pf 50V |
| 4 | 151-0056 | 1 | Cap Cer .047 uf 50V |
| 5 | 151-0058 | 10 | Cap Cer .01] uf 16V AX |
| 6 | 151-0060 | 3 | Cap Cer .1 uf 16V AX |
| 7 | 170-0223 | PC Board | |
| 8 | 212-0012 | 1 | Conn 6 Pin M |
| 9 | 230-0033 | Crytral 3.12 MHZ | |
| 10 | 280-0420 | 2 | Card Ejector |
| 1 | 313-0037 | 1 | C TLO81 CP |
| 12 | 313-0038 | 1 | IC TLO82 CP |
| 13 | 314-0058 | C 74LS08 | |
| 14 | 314-0062 | IC 74L874 | |
| 15 | 314-0067 | C 74LS30 | |
| 16 | 314-0072 | IC 74LS174 | |
| 7 | 314-0085 | 1 | IC 74LS14 |
| 18 | 314-0087 | 1 | C 74LS139 |
| 19 | 314-0100 | 1 | C 74LS8273 |
| 20 | 314-0042 | 1 | IC 7406 |
| 21 | 314-0131 | 1 | C 74LS3 73 |
| 22 | 315-0061 | 1 | C ST-32034 |
| 23 | 315-0077 | 1 | C 8035 |
| 24 | 315-0079 | 1 | IC (04053 |
| 25 | 316-0788 | 1 | C Prom Speech Bd Decoder |
| 26 | 471-0103 | 5 | Res 10K Ohm 1/2W 5% |
| 27 | 471-0106 | 1 | Res 10 Meg Ohm 1/2W 5% |
| 28 | 471-0222 | 1 | Res 2.2K Ohm 1/2W 5% |
| 29 | 471-0223 | 4 | Res 22K Ohm 1/2W 5% |
| 30 | 471-0274 | ] | Res 270K Ohm 1/2W 5% |
REF DES.
C2
C13, C46-C49 C6, C7
C10
c5, Cll, C12, C14-
17, Ci9, C20, C44
C9, C37, C38
Yl
Snap On U8
ull
U35
ul5
U37
U20
U38
U10
ual
u13
uy
u2
ul4
ul2
U30
R17, R21, R27-R29
R3
R24
R13, R14, R18, R22 R19
SPEECH BOARD ASSEMBL Y-Cont inued
ITEM_NO. PART NO.
471-0471
477-0002
- -0683
475-0022
151-0009
471-0472
21 -0001
213-0004
213 -0005
213-0008
213-0010
213-0012
471-0102 Qry
REQD.
nr CC eS ee Res
Res
Res
Pot
Cap Res
SKT
SKT
SKT
SKT
SKT
SKT
Res DESCRIPTION
470 Ohm 1/2W 5%
Pack 15x2.2k 68K Ohm 1/2W 5% _ 100K 10T PC MNT
Cer .003 uf 100V
4.7K Ohm 1/2W 5%
24 Pin Dual INLN
16 Pin Dual INLN
40 Pin Dual
20 Pin Dual INLN
8 Pin Dual INLN
28 Pin Dual INLN
1K Ohm 1/2W 5% DRAWING NUMBER 800-0294
REF DES.
R25, R26
RP2
R30
R74
c50
R20
XU3-XU7
xU30
xUN4
xu9, xU2I
xug, XUTI
xu2
R75
Speech Board Assembly
800-0294
as é oO. a a)
3 5
C3 8
G-80 POWER SUPPLY CHASSIS ASSEMBLY
Qry ITEM_NO. PART NO. REQD.
| 1 | 530-0016 | 1 |
| 2 | 250-0460 | 1 |
| 3 | 250-0461 | 1 |
| 4 | 800-0170 | 1 |
| 5 | 253-0206 | 6 |
| 6 | 281-0032-06 | 8 |
| 8 | 482-0104 | 1 |
| 9 | 313-0023 | 1 |
| 10 | 313-0014 | 1 |
| n | 313-0015 | 1 |
| 12 | 482-0100 | 1 |
| 13 | 482-0019 | 1 |
| 16 | 420-0557 | 1 |
| v7 | 280-0117 | 1 |
| 18 | 420-0575 | 1 |
| 19 | 281-0001-08 | 6 |
| 20 | 280-0341-00 | 6 |
| 21 | 310-0006-01 | 6 |
| 22 | 284-0001-00 | 6 |
| 23 | 284-0031-00 | 6 |
| 24 | 283-0021-00 | 6 |
| 25 | 800-0243 | 1 |
DRAWING NUMBER 800-0191
DESCRIPTION REF DES.
Heat Sink, G-80 Pwr Sup.
Chassis Support Cover
PCB Assembly PCB Support, Threaded Thread Forming Screw, #6 Type B, 3/8 long
TIP 141
320T5
340T12
320T12 TIP 125 Power Transistor
Negative 5 Volt Regulator Positive 12 Volt Regulator Negative 12 Volt Regulator Power Transistor (Audio Amp) Power Transistor (Audio Amp ) TIP 120
Fuse Decal
Tab Rivet Male 1/4" Power Supply B Decal Pan Head Phillips Screws, 4-40x1/2" Lg Shoulder Washer, #4 Transistor Insulator, T0-220 Flat Washer #4 Split Lock Washer #4 Machine Hex Nut, 4-40
G-80 Transistor Harness
Assembly P1
G-80 POWER SUPPLY CHASSIS ASSEMBLY-Cont inued DRAWING NUMBER 800-0191
QTy ITEM_NO. PART NO. REQD. DESCRIPTION REF DES.
| 26 | 800-0244 | 1 | G-80 Transistor Harness |
Assembly, P2
| 27 | 800-0245 | 1 | G-80 Transistor Harness |
Assembly, P3
| 28 | 800-0246 | 1 | G-80 Transistor Harness |
Assembly, P4
| 29 | 800-0247 | 1 | G-80 Transistor Harness |
Assembly, P5
| 30 | 800-0248 | 1 | G-80 Transistor Harness |
Assembly, P6
| 31 | 310-0007-01 | 1 | Transistor Insulator "H", |
TO-218
800-0191
G-80 Power Supply Chassis Assembly
Pa pale ea
rem 24 roswoenb
rem 19 VIEW ‘A" TYP.
G-80 POWER SUPPLY PC ASSEMBLY
ITEM_NO.
am PART_NO.
150-0088
150-0092
150-0095
150-0096
150-0097
151-0002
151-0007
151-0011
151-0012
151-0021
170-0222
212-0020
212-0081
313-0001
471-0011
471-0101
471-0102
471-0103
471-0104
471-0222 QTy REQD.
m= wy weston nw = DRAWING NUMBER 800-0170
DESCRIPTION .
Electrolytic Capacitor, 10 uf, 25V
Electrolytic Capacitor, 100 uf, 25V Electrolytic Capacitor, 3300 uf, 25V Electrolytic Capacitor, 6800 uf, 16V Electrolytic Capacitor, 4700 uf, 25V
Ceramic Capacitor, 100 pf, 50V Ceramic Capacitor,
-005 uf, 100V Ceramic Capacitor, -01 uf, 50V Ceramic Capacitor, -l uf, 50V Ceramic Capacitor, 20 pf, 50V PC Board
10-Pin Male Connector RTA
4-Pin Male Connector RTA
IC LM723 Dip Resistor, 10 Ohm, 1/2W 5% Resistor, 100 Ohm, 1/2W 5% Resistor, 1K Ohm, 1/2W 5% Resistor, 10K Ohm, 1/2W 5% Resistor, 100K Ohm, 1/2W 5% _ Resistor, 2.2K Ohm, 1/2W 5% REF DES.
C5, C8, C10, C18, C19, C23, C24, C26, C31 Cl7
C30
C3 2-C34
C15, C16, C27, C28
cg
C20
C21, C22, C25, c29
C2, C13, C14
c7
ul
R2
R32
R10, R27, R29 R6, R30 R23
R21, R22
G-80 POWER SUPPLY PC ASSEMBLY-Continued
ITEM_NO. PART_NO.
4710223
471-0332
471-0182 471-0681
473-05R0
473-00R2
475-0004
481-0002
481-0004
481-0006
482-0006
482-0014
514-0002
514-0003
514-0006
514-0008
800-0191
471-0220
471-0221 QTy REQD.
en Ce eC)
ro}
- so Ko HT wOnnnw DESCRIPTION
Resistor, 22K Ohm, 1/2W 5% Resistor, 3.3K Ohm, 1/2W 5%
Resistor, 1.8K Ohm, 1/2W 5% Resistor, 680 Ohm, 1/2W 5%
Resistor, .05 Ohm, 5W 3% Resistor, .2 Ohm, 3W 5%
Pot 1K Car PCMTV
Diode MR751
Diode MR501
Diode 1N914/1N4148
Transistor 2N4403
Transistor 2N4401
Fuse 3A Norm
Clip Fuse Mounting Fuse 1.5A Norm
Fuse 10A Slow Blow
Schematic Reference
Resistor, 22 Ohm, 1/2W 5% Resistor, 220 Ohm, 1/2W 5% DRAWING NUMBER 800-0170
REF DES.
R5, RO
R28
R26
R7
R25
R14, R15 R31
plo, 012 06-09, D11,
D13-D17
DI, D4, D5 Ql, Q7 Q2, Q3
Fl, F2
FA
F3
R8
R33
G-80 Power Supply PC Assembly 800-0170
©) S a §
AT ora” [fo |] | 0 ||o8 fo7 e®
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
800-0190
EMI Transformer Assembly
P25
BLK 3.00 76 |=
Coin System Assembly 800-3294
torsca 2 Lat O- —{—)- 3 tl a
FROM ITEM 4
WIKING FOR -00 ASSY WIRING FOR-Ol ASSY
AC Junction Box Assembly 800-0145
TO TRANSFORMER
won EM FLTER ay | x
ox GRAN ly INTERLOCK 3 ‘SWITCH. rs 3 BLU BLU BLK i r H ' ' a =
eI Z a alg GND STUD i ors ! 4.
FUSE HOLDER
L ‘AC PLUG
TTT
Game Electronics Assembly 800-3305
ITEM #10 eee ITEM Tl
ITEM #3 P/o ITEM #6
8 ee eee | cl See SH a
FIRE
THRUST THRUET
FIRE
Z PLAYER | PLAYER
REF ONLY
74L5 393
+5 ee +bca Olt
NOMENCLATURE. OR DESCRIPTION PARTS LIST UNLESS OTHERWISE SPECIFIED BIMENSIONS "ARE IN INCHES [CONTRACT NO. Bebo Ae Cremlin/seca FRACTIONS DECIMALS ANGLES ‘San Diego, Caiorrua 92123 APPROVALS DATE PW a we (4-6- 82 Single Player [CHECKED <> GRICE [4-882 | Control Panel __—_—aa a ———a intgetace CODE IDENT NO. |ORAWING NO. =e eS prLieaTON J a pe 800-0374
wld B.D00MHE MO AIS AI AIS 412 ALL Lf
i)
220 20 [| Ferber Fee Fee eee
- +5V c37-ca2 C44,C48 csitcel oe
(370-373)
45139 Tontess oTneRWIsE SPECIFIED DIMENSIONS ARE_IN INCHES. HFOLERANCES ARE: OoTa7 —— FRACTIONS DECIMALS ANGLES Gremlin Industries, inc. ‘San Diege, California 97723
(D0 NOT SCALE DRAWING
[zone [ura] otscrmon bare _T approve |
| [ | TAT RELEASED | CTC | Tio-ag- gol A. ARON | |
| [TB ecn #526 | CTC | finis-Be [arte | | |
| [CT ECN * GES | cre | Dia Tan | | |
[DT ECN OFFA cre lee Ee] [e | Perec waa GA. | Lee GHP FOR REY wes) ||
c28 220 PF | 220PF
RESET (SHT 6)
D5 (SHT 6)
D4 (SHT 6) peN~e8bN- 5
15™ 22002. > 48 PF F T ——__—_—. is ak (SHT 6)
is E a P i
PART OR, NOMENCLATURE IOENTIFING. NO. OR DESCRIPTION PARTS LIST FunRESS, OTHERWISE SPECIES 7 Gremilin Industries, inc. JBIMENSIONS ARE. IN INCHES. HTOLERANCES ARE: ‘San Bioge, California 92123
CPU Board
TBRAWING RO. 800-0107 ~|rofwd|rlollo uw
‘DO NOT SCALE DRAWING
TO 17 120-127
pS]
| 130-137 | 140-147 | 150-157 | 160-167 | “17 | 200: 207 | 210-217 | 220-227 | 230-237 | 240-247 |
| Jeo | . | 20 | 420 | c | deo | eo -_ | deo -" | dec |
ee... :
Ce E00
AVA AIS Al2 ALL 12 74t508
ve
T4508 uza)*
(ais)
{AL2)
D1 be D3 D4 DS Pe 07 Yeo 50-257
p-—> tars Se eSERHON 5 wichescn Y cacacec8, eT
| 10 | 3 | 103,65, | ,C4,C6,CB, |
| weg | c1o.eig, cis, | es.cucr4.cie, | Bian Ae ‘renes | Gremlin Industries, Ine. |
| cisci7.cia’ | cl8cetces, | r | CES Ag anates | San Diogo, Catitermin 92793 |
: xs 1 74Lsi0 anczz ces 25,C27,
| wu, | # | va) SUFFER | Olaf | Olas | a | G-80 2716 |
2 EPROM Board
REVISIONS: [ZONE] LTR. + DESCRIPTION SEE SMT. |
7ALSIS7} us
TALSISTY ue
DI Maa 29 = 1000 PF S
74LSIS7| u7
0 +5 A rs 2 s ia 4 CB THRU Cie 628 8 £ +01 ME
TALSIST| us
7aLsi57| ua
sb
7ALSIaL 1, THS8e u20 Z_))u2a>3—y
4 THSBe 7 PART OR NomencUaTURE 5} juza Lil IDENTIFYING NO. OR DESCRIPTION, alli PARTS LIST Gremiin Industries, Inc. San Diege, California 92723
BG PIN CONNECTOR .
X-Y Timing Board
24 PIN SOCKET . a a 800-0161 4 PIN MOLEX .
"APPLICATION 1DO_NOT SCALE_DRAWING
X-Y Timing Board
| 6 | 3 | 2 | 1 |
ar REVISIONS
| +12 | DESCRIPTION | Dave | APPROVED |
+s SEE SWT. E) aula fea dint Baz Ho 3143 a Sas uaa Le AS 2708 +
| 2 la | . | D |
a7 + Blas .
| Za3 | alalaiotie | ——, hebriajale 74/3 |
n
| fae | uss] | Tusa | |
| Be | T4Ls374 | z | yaisa7a |
‘4 S04 t
- Taq TS]2]9 es] wes
+ +
- RAW
4 7so0 Suze CL
VoL +
t
+
+ —
| leiz/3)5 | Islel3|z babs|elu | Isle] |2 hahsiz|u | ||||
| 7415244 | af | uaz | le | i | was | 27500, |
| use | Co saiszas °* | yaszaa [7 | + fue | Fo | ||
| clajrhs | @ rs Jo | so | yi Ja fo | & | a 7500 | |
| 7aLS04 | (2 |u28 | YCL |
w +5 B
| 13 | 2) | a | u AB | |
| iz] u36 | z | vas, | we | |
| 4 | S| raisivs: | 3 | iratsi7s | TaLs74 |
| a | 3 | wz] uzs | | ov, | ow |
| mac | 7 Y | 4570 |
4 =
| 2 | 2,48 5 | Ss | ||||
| ra | 36 | t | + | ovux | 3 | |
| B | 2 | le | 74USI75 | t | THS74 | ; |
| wz] 037 [7 | 18 | 3huzs | ro) | |||
| S| 4817515 | p> | S | ||||
| 4 | 10 | a] | cd |
> +5 4 : 3
| cone | PART OR | NOMENCLATURE |
Qo] Gent | roentync no. Oe SCRIPTION T PARTS LIST Bitenswone ane NHES Gremlin Industries, Inc.
| |FRACTIONS DECIMALS | ‘Sam Brower | A |
(CODE TENT NO:[ORAWING NO 800-0161 REV P [SCALE NONE, [sneer © OF
t [sles
u3i T4LsiO7
yl FALSI61 CK ue uZ4 Kar lg ee
T4LSIO7 7ALsio7
ua [T —
a is aS
l20
aBeD USO 74LSIS4 012345678 90 Z13HIS TROMENCLATURE: OR DESCRIPTION.
TESS OTMERVTSE SPECIFIED Gremlin Industries, inc. San Biege, California 92193 ARENSON ARE IN INCHES DECIMALS ANGLES
-Y Timing Board
v CODE ERT) wiry 61 ®
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
REVISIONS
MULTIPLY CLOCK (17)
7aLs04
a[alelsie 10 IS 45 12) 9 fo] 7aLsiel
- usz
To sHTS
TALS374 uz
les
© = 41m wo.ex
© «= 24 em socner NOTES © D} = BPM comector - R4 +128 INgi@.
D3, a! 2N4403
R?
Gremlin Industries, Inc. San Diege, Catitornis 92113
00-0054 ‘USED ON "APPLICATION. DO NOT SCALE DRAWING
X-Y Control Board
800-0163 [CODE TENT iz J
oe Dr bz D3 D4 Ds 73a" 6"
Alas Alz
£ +5 [zone [rey bescriprion TT bare [APPROVED | [TSE SHTT FOR REV. es |
ge Bee +5 A pe ta K c
] H ot: 3 oy 20 at [ie 20 Ter 18 420 Te 1 20 2r
DE/CE VPP/AN CE/Ail A10 Ag AB U7
PROG
an lol vlolafalufol—_ |RieIR}o DE/CE VPP/AII CE/AII
U6
DATA
2716 DE/CE VPP/AIl CE/AII Alo Ag AB Alo Ag AB US
DATA
2716 Az AG AS At A3 AZ Al AS lol |olur]+]eo}r]— DE/CE VPP/AII CE/AI/ DE/CE VPP/AII CE/AI) Alo Ag As U4 4 u3
DATA Az DATA AG AS 27/16 “3 2716 Ag AZ Al Aw
re 1S
ime 18. IF
Dg Di D2 0304 D5De 07 DRA DATA PRESENT.
v2
ss
+ cs, cla C16, C20
-O1UF
ci, cis 638
O1UF | .JUF
cu, C37 C17, INSTALL Gremlin industries, Inc. ‘San Diege, California 9203
JUMPERS
PROG DATA 2716 Ac E,S77K/M; 16
TMs 2532 [AD 72732 BC F;G/I7K/M; "32" E|H/U/L ZN; 32"
Speech Board
[CODE TENT NO, DRAWING NO. 800-0294
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
I
iziY 36} £500 L SOC
ba D3 LZ DI mn 1% u3¢ Es 2A 6286!
ye 745138 LT -T see sar 7
MOMENGLATURE OR DESCRIPTION. PARTS LIST ST as wou Dromlin/ B&G
ea —_| ; zzz} Universal Sound Board rT
"APPLICATION. Le | 800-0877
REVISIONS, ‘DESCRIPTION RELEASED a
fre uF
R22
rook
TIP 14h
® }. FOR FUTURE USE
fel 14 hu AUDIO IN #2
fev t
WHT/ORN Ss
RI Ri
N
iH -) 1H
war ©
f 15 VAC 7 t +
TO COLOR TER MONITO! RASTER MONITOR p----4 WHT/B LK 4 100 VAC gti 320 7-5 Tes [ees ess Ho +] 3300uF .orur + iour com Ras rey BLK 2200. 4 yo2 9 Ned
TIP 125
BRN r
sj \ BRN/BLK i i BRN 4 - + i N
Tr
pee 244 G.80 Power Supply RP Ae: _ fo) s00.0181 || 2 eine 24
pent HONE. Toner Sor
NOTES 1 URESS omerWse_ SPEC ED RESISTANCE (aIK~Ka M-Ma | Granaeot Fesetoe | BEES oo comune ILI] A REPLACE” ALL COMPONENTS MARKED -~> Uitm Sure Seb. WintToENEAT Hee "= |
pia}
—a- <a ae
Ae
Model Number GO8-003
00°4177-04
19” X-Y Color Monitor 200-0025