Tempest Caberat TM-196 1st Printing
Tempest (rev 3, Revised Hardware) (Atari, 1980) · Technical Manual · 60 pages · 50 sections · original scan

This page is a drawing, shown as the original scan.
GAME SERIAL NUMBER LOCATION Your game’s serial number is stamped on a label on the outside of the game. The same number is also stamped on the chassis of the monitor, Regulator/ Audio || PCB, and the Tempest™ Analog Vector-Generator PCB and Auxiliary PCB. Please mention this number whenever calling your distributor for service.
VIDEO DISPLAY
REGULATOR/AUDIO II PCB
AUXILIARY PCB GAME SERIAL NUMBER IDENTIFICATION TAG
ANALOG VECTOR. GENERATOR PCB
POWER SUPPLY ® bi J
Introducing Atari’s First Color XY Video Game...
Operation, Maintenance and Service Manual
Complete with Illustrated Parts Lists
Tempest™/Cabaret™
Copyright © 1981 by Atari,Inc. _—_ All rights reserved. No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher.
The Tempest™ game play, all graphic designs, this technical manual, its accompanying schematic diagrams, the display manual, and the troubleshooting guide are protected by the new Copyright Act of 1976.
This Act provides for increased penalties for violating federal copyright laws. Courts can impound infringing articies while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles.
In addition, the Act provides for payment of statutory damages of up to $50,000 in certain cases. Infringers may also have to pay costs and attorneys' fees, fines up to $25,000, and face an imprisonment of up to one year.
Atari will aggressively enforce its copyrights against any infringers. We will use all legal means to immediately halt any manufacture, distrioution or operation of a copy of video games made by us. Anyone who purchases such copies risks forfeiting such a game.
Published by: ATARI INC. 1265 Borregas Avenue PO. Box 427 Sunnyvale, California 94086
Lithographed in the U.S.A. 10K
Tempest /Cabaret™
Notice Regarding Non-Atari Parts
WARNING
Use of non-Atari parts or modifications of your Atari game circuitry may adversely affect the safety of your game, and may cause injury to you and your players.
Atari, Inc.’s warranty (printed on the inside back cover of this manual) may be voided, if you do any of the following:
1,) you substitute non-Atari parts in your coin-operated game, or
2.) you modify or alter any circuits in your Atari game by using kits or parts not supplied by Atari.
Not only may the use of any non-Atari parts void your warranty, but any such alteration may also adversely affect the safety of your game, and may cause injury to you and your players.
Tempest™/Cabaret™
Table of Contents
omnmo Set-Up Procedures A. New Features 1 B. Game Inspection 3 C. Game Installation. . 4
- Voltage Selection . . 4
- Interlock and Power On/Off Switches . 5 D. Self-Test Procedure ............... . 6 E. Option Switch Settings - 10
- Bonus Play Feature . . 10
- Coin Mechanism Multipliers . 21
- Examples of Game Price Settings . 211 F. GamePlay .............000 eee ~ 13
- Attract Mode . 14
- Ready-to-Play Mode ....... 15
- Play Mode .......... 15
- High Score Initial Mode ....... 060.60. c cece eee eee 16
Maintenance and Repair A. Cleaning..... beeen eee eee : . 18 B. Fuse Replacement . 18 C. The Control Panel....... - 18
- Leaf Switch Replacement... 19
- LED Start-Switch Replacement ... 19
- Encoder Wheel Maintenance and Repai - 20 Video Display Removal .............. .21 Fluorescent Tube Replacement Printed-Circuit Board Removal . Game Operation... 0.06. i cent e eee e eee e ee 24
Illustrated Parts Lists Nlustrations and parts lists begin on page ........-.........00 eee 27
Tempest ™/Cabaret™
List of Illustrations
Figure 1 Overview of Game .... 0.0.66 cence eens 2 Figure 2 installation Requirements ... 4 Figure 3 International Voltage Plug Selection 4 Figure 4 Interlock and Power On/Off Switches .. . 5
Figure 5 Location of Self-Test Switch, Volume Control and Option Switches 6 Figure 6 Self-Test Procedure Figure 7 Game Option Settings . . Figure 8 Game Price Settings... . 0.00... 6... cee cee een eee
Figure 9 Coin Counter Option Settings ...... 6... cece eee cee eee eee 13 Figure 10 Opening the Contro! Panel . . 18 Figure 11. Control Panel Wiring ............ . 19 Figure 12 Encoder Wheel Maintenance and Repair ....................0005 20
Figure 13 Video Display Removal............. 0.02 c cece eee eee eee 21 Figure 14 Fluorescent Tube Replacement . - 22 Figure 15 — Printed-Circuit Board Removal . - 23 Figure 16 Power Distribution ....... - 24 Figure 17 Signal Distribution .......... 6... c cece ccc eee eens 25
Illustrated Parts Lisis: Figure 18 Cabinet-Mounted Assemblies Figure 19 Control Panel Assembly. . . Figure 20 Encoder Wheel Assembly .. . Figure 21 Regulator/Audio ll PCB Assembly .
Figure 22 Tempest™/Cabaret™ Auxiliary PCB Assembly ...........-..022005 Figure 23. Tempest™/Cabaret™ Analog Vector-Generator PCB Assembly Figure 24 Fluorescent Light Assembly : Figure 25 Power Supply Assembly for Color X-Y Games..........-......0005
Figure 26 Vertical-Mounted Coin Door ...... 06... ee eee eee ee eee eee 46
Tempest™/Cabaret™
vi
WEST and CENTRAL U.S.A. Parts for all Atari customers in the U.S.A. Game sales and service
Atari, Inc. California Customer Service Office 1105 N. Fair Oaks Avenue P. O. Box 427, Sunnyvale, CA 94086 Telex 17-1103 (Monday-Friday, 7:30-4:00 pm Pacific Time) = From California, Alaska or Hawaii (408) 745-2900 ae From anywhere else in this area toll-free (800) 538-1611
EAST U.S.A. Game sales and service only
Atari, Inc. 7) New Jersey Customer Service Office 12A World's Fair Drive, Somerset, NJ 08873 Telex 37-9347 (Monday-Friday, 7:30-4:00 pm Eastern time) = From New Jersey MISS: (201) 469-5993 From anywhere else in this area s toll-free (800) 526-3849
EUROPE Parts for all Atari customers in Western Europe. Game sales and service
Atari Ireland Limited European Customer Service Office TIPPERARY TOWN, Tipperary Town, Ireland IRELAND Telex 28165 (Monday-Friday, 9:00-6:00 pm GMT)
@ 0062-52155
Set-Up Procedures
Introduction
This manual, written for game operators and service technicians, describes the Tempest™ game. Chapter One explains new game features, game set-up, self-test procedures, option switch settings, and game play. Chapter Two consists of maintenance and repair information. Chapter Three contains illustrated parts lists.
A. New Features
The Tempest™ /Cabaret™ game has five new features. Even if you are familiar with Atari games, you should note these important differences. The new features are: @ Color XY Display and Game PCBs. Tempest is Atari's first color XY game. The color display produces a great number of colors in varying intensities. Atari’s X-Y game circuitry has been redesigned for a color display. @ Game Play. Atari introduces Skil/-Step™, and 99 levels of play on 16 different playfields. A demonstration mode allows you to accelerate through 98 levels of play. In addition, a special switch setting lets you freeze the game action (see Section F, Game Play).
Tempest “iCabaret™
MONITOR SHIELD COLOR X-Y MONITOR
~ NCODER- WHEEL CONTROL CONTROL PANEL
LUGGAGE-STYLE ; | LATCH
ATTRACTION PANEL
‘REGULATOR/ AUDIO PCB
COIN DOOR’
AUXILIARY PCB
ANALOG VECTOR: GENERATOR PCB
POWER ON/OFF SwiTCH
POWER SUPPLY
Figure 1 Overview of Game
@ Encoder Wheel. This new control has a compact, simplified design which makes servicing easy. This control's circuitry is contained on a single PCB. The very smooth action is designed for greater player accuracy. @ Coin Door. This game has Atari’s new verticalmounted coin door. It allows full access for servicing the coin acceptors and other electrical parts, yet provides security for the cash. Therefore, the two doors are separately keyed. @ Cabinet Design. The display shield is made of tempered glass to facilitate cleaning and improve visibility. Also, the attraction panel, with its mew construction, uses polycarbonate silkscreened to tempered glass. In addition, there is a fluorescent tube behind this panel. New iuggage-style latches allow easy opening of the control panel. Finally, the game and auxiliary PCBs are mounted back-to-back on the cabinet wall and are separated by plastic standoffs. These new features, as well as all other major parts in the game, are illustrated in Figure 1. Throughout this manual, wherever one of these new features is mentioned, you will see this symbol:
B. Game Inspection
This new game is ready to play upon removal from the shipping carton. However, your careful inspection is needed to supply the final touch of quality control. Please follow these steps to help us insure that your new game was delivered to you in good condition.
2. Tempest ™/Cabaret™
Examine the exterior of the game cabinet for dents, chips, or broken parts. Remove the screws that were used as extra security to seal the rear access panel. Unlock and open this panel, as well as the coin door, inspect the interior of the game as follows: @ Check that all plug-in connectors (on the game harness) are firmly seated. Replug any connectors found unplugged. Don’t force connectors together. The connectors are keyed so they only go on in the proper orientation. A reversed edge connector will damage a PCB and will void your warranty. @ Check that all plug-in integrated circuits on the game PCBs are firmly seated in their sockets. @ Check that the plastic standoffs are in place, holding the PCBs away from each other. @ Remove the tie-wrap that holds the coiled power cord on the inside cabinet wall. Check the cord for any cuts or dents in the insulation. Place the square black plastic strainrelief plate in the wood slot at the bottom of the rear panel opening. @ Note the location of the game’s serial num: ber—it is printed on the special label below the control panel on the front of the game cabinet. Verify that the serial numbers on the Tempest™ Analog Vector-Generator PCB, Tempest Auxiliary PCB, Regulator/Audio II PCB, power supply and video display are all identical. A drawing of the serial-numbered components is on the inside front cover of this manual. Please mention this number whenever you call your distributor for service. @ Check all major subassemblies such as the power supply, control panel and monitor for secure mounting.
Tempest “icabaret™
Cc. Game Installation
Figure 2 Installation Requirements
Power 250 watts maximum Temperature 0 to 38°C (32 to 100°F) Humidity Not over 95% relative Space Required 52 x 78% cm (20% x 31 in.) Game Height 154 cm (60% in.)
Line Voltage Range 90-110 VAC (100) Violet 105-135 VAC (120)* Yellow" 200-240 VAC (220) Blue 220-260 VAC (240) Brown *This is the only plug provided on the North American power supply.
Figure 3
- Voltage Selection The power supply used in this game operates on the line voltage of almost any country in the world. The power supply comes with either one, two or three colored voltage selection plugs.
Before plugging in your game, check your power supply. If the supply doesn’t have voltage selection plugs and a connector at J3 (see Figure 3), then the game operates on any voltage from 105 to 135 VAC. {f the supply has the colored voltage selection Plugs, make sure that the voltage selection plug on the power supply is correct for your location's line voltage. Check the wire color on the plug and see if it is correct per Figure 3.
VOLTAGE SELECTION
International Voltage Plug Selection
- Interlock and Power On/Off Switches To minimize the hazard of electrical shock while working on the inside of the game cabinet, an interlock switch has been installed (see Figure 4). It is located behind the access panel. This switch removes all AC line power from the game circuitry when the panel is opened.
Check for proper operation of the interlock switch by performing ihe following steps: @ Be sure the rear access panel is closed. @ Plug the AC line power cord into an AC outlet.
SWITCH
POWER ON/OFF SWITCH Tempest™/Cabaret™
Set the power on/off switch to the “on” position. Within 30 seconds the monitor should display a picture. Slowly open the rear access panel. The monitor picture should disappear when the panel is opened approximately 2.5 cm (1 inch). Close and lock this panel. If the results of the preceding step are satisfactory, the interlock switch is operating properly. If the monitor doesn’t go off as described, check to see if the interlock switch is broken from its mounting or stuck in the “on” position.
Figure 4 Interlock and Power On/Off Switches
Tempest™/Cabaret™
D. Self-Test Procedure
This game will test itself and provide data to demonstrate that the game’s circuitry and controls are operating properly. The data is provided on the monitor and the game speaker; no additional equipment is necessary.
SELF-TEST switcH
UTILITY COIN SWITCH
Kort
ANALOG VECTOR-GENERATOR PCB >
Fel — VOLUME CONTROL
[a Part 1 of the self-test procedure includes a display of the operator-selectable game options, and game time and high score table information. Part 2 includes ROM and RAM, control panel and monitor information.
We suggest you run the self-test procedure any time you collect money from the game or any time you change the game’s options. Refer to Figure 5 for location of the self-test switch and option switches. To run the self-test, follow the instructions outlined in Figure 6.
Figure 5 Location of Seli-Test Switch,
Volume Control and Option Switches
Tempest “iCabaret™
Figure 6 Self-Test Procedure Part 1 “ se
The information below is displayed on the screen if you set the self-test switch to on during the attract mode. Look at the dispiayed numbers for SECONDS ON and SECONDS PLAYED. li these numbers run together vertically, make adjustments to the X-BIP and Y-BIP potentiometers on the game PCB.
COIN MECH MULTIPLIER
SWITCH AT N13 (Coin Modes)
SWITCH TOGGLE 1 To go to Self-test Part 2, rotate the control knob until the message PRESS FIRE AND SUPERZAPPER FOR SELF-TEST appears on the monitor. Then press both FIRE and SUPERZAP- PER. To end the operator information display, set self-test switch to off.
TIME GAME ON (Seconds) PRESS FIRE AND ZAP FOR SELF TEST | TIME GAME ON 7 Qa PLAYED (Seconds) PLay +———_L____ No. oF pe eee GAMES NO. OF 2-PLAYER GAMES
AVERAGE GAME TIME foo ooo00 00 qgooo000 ~~ swren _ pono TOGGLE 8
SWITCH AT L12 (Game Play) oo repIn SWITCH AT DIE2 LIVES (Game Difficulty)
PER GAME GAME DIFFICULTY
CREDITS. @ MCMLXXx ATARI ‘ sohus EVERY eCOGD : OE NSE — con move NO. OF LANGUAGE (English)
Operator Information Display
To erase High Score Table: 1, Turn control knob until top line reads PRESS FIRE AND START 2 TO ZERO SCORES.
- Press both FIRE and START 2.
- The word ERASING appears and blinks on the screen until the entire tabie is erased. Wait until the word ERASING disappears before continuing with other tests. To erase Game Times:
- Turn control knob until top line reads PRESS FIRE AND START 1 TO ZERO TIMES.
- Press both FIRE and START 1.
- The word ERASING appears and blinks on the screen until the entire table is erased. Wait until the word ERASING disappears before continuing with other tests.
[Seli-test is continued on next page]
Tempest ™/Cabaret™
{Instruction Test Passes Figure 6 Self-Test Procedure Part 2
Test Fails
- Set self-test switch to on (see Figure 5). Press RE- SET on the PCB, or turn power off and After about 5 sec- ‘onds, the moniter displays the picture below. No sounds are produced. RAM FAILURE is indicated by a sequence of 1 to 12 tones and an R displayed in top half of screen. You will hear a short low tone and see a short flash on the LED start pushbutton for each good RAM chip, and a long high tone accompanied by a long pulse on the start pushbutton for a failing RAM chip. The test stops with the first failing RAM. To restart the sequence, press RESET on the PCB, or power game to off, ‘on again. then to on again. Identity the bad RAM chip with the table below. Example: four short aupio low tones followed by a long high tone indicates failure of RAM at location M3. ISBAD ENTIRE WHITE FRAME Bad RAM Chip Location VISIBLE AND WI
Rom Ar RI WINCH OF monhoh EDGE Long High Tone on Analog Vector-Generator PCB
si ~ Ist Re x 2nd P2 3rd R4
| TOGGLE | ath | Pa |
TOGGLE 2 SWITCH 8 5th M3
| SWITCH 1 | 6th | Ma | ||
| TCH | SWITCH AT L12, | 7th | L3 | |
| ule | ilalayainalaltg | (Game Play) | ath | la |
eon ne DopECoOn:
| (Coin | Modes) | See | SWITCH AT D/E2 | 9th | K3 |
| (Game Difficulty) | 40th | Ka | |||
| START 2 | eal 000 | aL | CONTROL | 1th | J3 |
| mae | rath | u4 |
START 1
FIRE
SUPERZAP UTILITY COIN SWITCH
‘SLAM SWITCH a RIGHT COIN MECH
‘LEFT COIN MECH ROM FAILURE is indicated by a vertical pair of hexadecimal numbers on the top of the screen. The top number indicates the iocation of the failing ROM(s). Ignore the bottom hexadecimal number in the pair. Identify the bad ROM with the table immediately below.
Displayed No. Bad ROM Chip Location PCB Location RI P41 MINI uUM1 K1 wv Ht FI
D1 R3 NIP3* Analog Vector- Generator PCB O-NORUOVNOOPOD
EAROM, Audio and Math Box Failure are indicated by a single letter in the center of the display. Identify the failure with the table below.
Displayed Letter Failure PCB Location
| E | EAROM | 3 (Aux. PCB) |
| P | Audio 1 | B/C2 (Aux. PCB) |
| Q | Audio 2 | C/D2 (Aux. PCB) |
R RAM See RAM test above M Math Box**
- If this ROM is bad, you will hear a continuous low tone, and the program may be unable to display a screen image. **Math-box failure is explained in TM-195, Tempest Troubleshooting Guide.
[Self-test is continued on next page]
Instruction Tempest ™/Cabaret™ Figure 6 Self-Test Procedure Part 2, continued Test Passes Test Fails
- Activate start, fire, Superzap, SLAM, and coin switches.*
- Rotate encoder wheel clockwise and counterclockwise.
- Observe the white frame around the outside of the screen.
- Activate SLAM switch.
- Activate SLAM switch.
- Activate SLAM switch.
- Activate SLAM ‘switch.
- Activate SLAM switch.
- When satisfied with test, set selftest switch to olf position. As switch activates, you'll hear a beep and 0 changes to 1 on the screen.
The right hexadecimal number on the screen will increase with counter clockwise motion, and decrease with clockwise motion.
Each frame corner should be within Ye-inch of each monitor bezel corner.
A white cross hatch pattern appears. A character set appears at the bottom of the screen.
Horizontal and vertical lines cross in the center of the screen displaying a large “plus” sign, Audio VO 1 and 2 altemate to produce four tones,
Tests purple, cyan, yellow, white, green, blue, and red for color and intensity. Displays seven groups of vertical lines, each with right line the brightest and left line the dimmesi
A checkerboard pattern touches the sides and corners of the monitor. Rotate the control kneb to change color.
A white frame is displayed on the screen. You will not hear a beep and 0 will remain on the screen for the defective switch.
Incorrect progression of numbers indicates encoder wheel harness wires were connected incorrectly. No number change indicates encoder wheel is bad or harness wires are loose.
Consult Tempest™ Drawing Package to adjust video pots.
if display is not centered and symmetrical on the monitor, adjust video pots (see Tempest Drawing Package) on the main PCB, If character set is incorrect, check Vector ROMs (see Troubleshooting Guide).
No sound indicates failure of an audio amplifier andior the custom audio chip(s).
Use this pattern for tracking adjustments (see the Color X-Y Monitor Manual).
Use this pattern for purity and convergence adjustments (see Color X-Y Monitor Manual).
“Activate coin switches by inserting at Jeast one coin in each coin siot. You will not trip the coin counters as long as you are in seli-test.
Tempest ™iCabaret™
E. Option Switch Settings
- Bonus Play Feature Tempest™/Cabaret™ offers a bonus play for certain combinations of coins inserted. This bonus feature is operator-selectable, meaning you may choose to offer it or not. With your game set at 25° per play, players who deposit four successive quarters, then press the start button, can receive a bonus play. Therefore, players can receive 5 plays for $1.00.
This bonus feature encourages players to insert more money than just the minimum 25¢ required for one game. Various other bonuses are also available (see Figure 8).
Figure 7 Game Option Settings To change toggle positions on the switch assemblies, you need not remove the game PCB. The switches are accessible when the Tempest™ Analog Vector-Generator PCB is mounted in place. To change positions on the Auxiliary PCB slide the board out as far as possible. When changing the options, verity proper results on the monitor display by performing the self-test. Note that changing an option on any of the following eighi toggles will not cause an immediate change on the monitor screen during the attract mode.
Settings of 8-Toggle Switch on Tempest Analog Vector-Generator PCB (at L12)
| 1 | 2 | 3 | 4 | 5 | 6 | : J | 8 | Option |
On 1-credit minimum $ Off 2-credit minimum
| On | On | English | $ |
On Off French
Off On German
| Off | Off | Spanish |
Bonus life granted at every:
| On | On | Off | 10,000 points | |
| On | On | On | 20,000 points | $ |
| On | Off | On | 30,000 points | |
| On | Off | Off | 40,000 points | |
| Off | On | On | 50,000 points | |
| Off | On | Off | 60,000 points | |
| Off | Off | On | 70,000 points | |
| Off | Off | Oft | No bonus life | |
| Off | Off | 2 lives per game | ||
| On | On | 3 lives per game | $ | |
| On | Off | 4 lives per game | ||
| Off | On | 5 lives per game |
Settings of 4Toggle Switch on Auxiliary PCB (at D/E2).
Off Off
Off On
On Off On. On
2 oit =
On Game difficulty” Medium $ Easy Hard Medium Starting Level: Ss 4,3,5,70r9 $ 4,3, 5, 7, 9 or 11 if current high score 300,000-499,999 1, 3, 5, 7, 9, 11 or 13 if current high score
1, 3,5, 7, 9, 11, 13 or 15 if current high score more than 700,000
$ Manufacturer's suggested seitings
- Easy—Enemies move slower and one less enemy shot on the screen at one time. Hard—One more enemy, enemies move faster and 1-4 more enemy shcts on the screen at one time. For pricing for “credits,” see Figure 8. Changing toggles 1-5 erases the high score table.
- Coin Mechanism Multipliers In this game, Atari uses its new vertical-mounted coin door which has two mechanisms. The multipliers determine how much each coin mech will be worth to the game’s logic.
The basic unit of measurement is 25¢ or 1 DM, which equals a multiplier of x1. Therefore, if you have a 1 DM/2 DM coin door, you will probably want to set the left and right option-switch multipliers at xx 2.
You can set these multipliers with toggles 4 through 6 on the Tempest™ Analog Vector-Generator PCB switch assembly at location N13. For exact settings of these toggles, refer to Figure 8.
Figure 8 Game The table below contains the switch settings for options relating to game price, coin mechanism multipliers (German coin doors), bonus play, demonstration and freeze mode.
The Demonstration Mode allows you to choose any level (1-81) in the ready-to-play mode and accelerate through as many as 99 levels without having to kill the enemies. The Demonstration- Freeze Mode* * allows you to stop the action. The score is zeroed at the end of the game in this mode. Tempest ™/Cabaret™
- Examples of Game
Price Settings
Figure 8 explains the game price settings, giving six examples of the most common U.S. situations. The toggles mentioned in Figure 8 are all in the switch at location N13; they only relate to game price, coin mech multipliers, and bonus plays.
Figures 7, 8 and 9 provide “$” symbols indicating Atari's recommended settings. All toggles are preset in the “on” position as per these recommendations. However, you may change the settings to suit your individual needs.
Set the toggles per the table below for the Demonstration Mode. Next, rotate the control knob. You may choose level 1 through 81 during the ready-to-play mode. Press either START button to accelerate through the tubes. Press the FIRE button to clear the spikes at the bottom of the tube. To freeze play, set switch 1 to off.
Toggle Settings of 8-Toggle Switch on Tempest Analog VectorGenerator PCB (at N13) 1 2 3 4 5 6 7 Option
Off Off On On
On On Off Off on Off On Off
On Off
On
On
Off
Off
Demonstration and
On Off Off Off Off Off On Off On Off
On On Free play 1 coin* for 2 credits 1coin* for 1 credit $ 2 coins* for 1 credit
Righi coin mech x 1 $ Right coin mech x 4 Right coin mech x 5 Right coin mech x 6 Left coinmech x 1 $ Left coin mech x 2
No bonus coins $
For every 2 coins inserted, game logic adds 1 more coin* For every 4 coins inserted, game logic adds 1 more coin* For every 4 coins inserted, game logic adds 2 more coins* For every 5 coins inserted, game logic adds 1 more coin* For every 3 coins inserted, game logic adds 1 more coin*
Freeze Mode** 5
Demonstration Mode Demonstration-Freeze Mode
$ Manufacturer's suggested settings
- In the U.S., a “coin” is defined as 25%. In Germany a “coin” is 1 DM. ** If you press RESET during this mode, game will lock up. To recover, set switch 1 to on. To achieve bonus plays, all coins must be inserted before pressing Start button.
an)
Tempest ™/Cabaret™
Figure 8 Game Price Settings, continued
The white block below contains Atari's suggested settings. All Circled numbers refer to gar e pricing labels you should use numbers 1 thru 8 are toggie settings on the 8-toggle switch at lo- with each situation (labels are below). Use the label no. 6 (incation N13, on the Tempest™ Analog Vector-Generator PCB. dicated with) only if you set toggle 8 at PCB switch assembly L12 to off.
50¢ PER CREDIT: Bonus Bonus 8.75 = 2 plays
| No benus | $1.00 = 3 plays | $1.00 = 3 plays | |||||
| BO | A | BOE Brg | OT | oe | eee | ||
| 250/25¢ | x | On | On On, On” | Of On | “On | On | Off On. |
| Mechenisms — |) | 5 | 68 TB | 8 | BB | Te | ||
| On On On Off | On. | On | On-Off |
u
25¢ PER CREDIT:
Bonus Bonus
| No bonus | $.50 = 3 plays | $1.00 = 5 plays | ||||||||||
| 1 | 2 | 3 | 4 | RiGee Qe | Bagger SS Pee Aes | Se | ||||||
| 2sc/25¢ | @ | On | On | On | On | On On (Off On - © on on | Ones | Od | ||||
| Mechanisms | ® | 5 | 6 | 7 | 8 | Iq 8 | © | 7 | 8 | [Qs | 6.7 | 8 |
| On | On On On | 08 On On On | |e | On On On | On |
ne @®@ 2 coins Game Pricing Labels: “8 @@@ 3 coins 0080 @ 4 coins
| Ct) | © | @@ 2 coins =1 play | |
| AL | @@ 2 coins =1 play | A | @ 5! coin = 3 plays |
(Susan B. Anthony coin}
| e | ©, | @ icoin = 1 play |
| in | = | A |
dS @ 1 coin = 1 play iat 2 play minimum (2 coins = 2 plays) ATARI
AO @ @ 2 coins = 1 play (For operator use—write in
Aran the appropriate phrase. Use a permanent-ink water-resis- @ @ @ @ 4 coins = 3 plays tant marker.)
Tempest™/Cabaret™
Figure 9 Coin Counter Option Settings
[These toggles determine which coin mechanisms activate which counters)
Toggle Settings of 4-Toggle Switch on Analog Vector-Generator PCB (K10/11) Two coin acceptors
| 4 | 3 | 2 | 1 | in the coin door: |
| On | Off | Both acceptors activate all coin count- |
ers simultaneously.
| > | > | Off | On | Both acceptors activate 2 counters |
| 3 | 8 | separately. $$ | ||
| 3. | 8 | pare | ||
| = | 2 | Off | oft | Both acceptors activate 2 counters |
separately.
| On | On | Both acceptors activate all coin count- |
ers simultaneously. $
$ Manufacturer's suggested settings for games with 1 coin counter. $$ Manufacturer's suggested settings for games with two coin counters.
F. Game Play <@
Atari’s Tempest™/Cabaret™ game is a one- or two-player game with a color X-Y or vector-generator monitor. This new monitor, with its 3-color guns and higher voltage, has the same iechnology that was used in Atari's black-and-white X-Y monitors. However, this new monitor displays dazzling color and unique visual effects in a spectacular threedimensional video display.
Tempest™/Cabaret™ introduces additional new features: @ Skill-Step™ with 99 skill levels of play ®@ Operator-information display @ Demonstration mode with freeze
Skill-Step™ allows a player to start a game at the same level as was previously achieved (he must start the next game within 30 seconds), without having to start over at the beginning levels. Therefore, skillful players continue to be challenged while less experienced players try to master higher levels. The 99 skill levets of play include 16 different playfields and 6 different targets.
The Operator-Information Display is a special sequence in the self-test mode displaying game-time information: number of seconds the game has been on and been played and the average game time. This display lists the number of one- and two-player games played, option switch settings, number of lives, level of difficulty, bonus levels, credits, and game pricing information. In this mode, you may clear the special “permanent” memory by erasing the high-score table or game-time information. The word ERASING appears on the screen during either of these processes.
The Demonstration Mode allows you to accelerate through 98 tubes by blasting down the tube toward the far rim without having to kill the enemies. Also, you can freeze game action so you can enjoy the dazzling effects of your journey through the tubes.
In addition to these new features, Tempest™- Cabaret™ has five possible modes of operation: attract, ready-to-play, play, high score initial and selftest. Self-test is a special mode for checking the game switches and computer functions. You may enter self-test at any time (if you enter Part 1 all credits are retained; enter Part 2 and all credits are cancelled). Wait at least eight seconds after a game has been played before entering self-test or turning off the power. Otherwise, you may erase the high score table.
Tempest “iCabaret™
- Attract Mode
The attract mode begins when power is applied to the game, after a play or high score initial mode, or after self-test. This mode is continuous and is only interrupted when a game is paid for and accepted, or when in self-test. in the attract mode, the monitor displays one of three possible pictures.
One of the pictures is the high score display which lasts for 12 seconds. The score(s) from the last game is at the top of the screen. Foliowing is the highest score and player’s initials. The top eight scores and their matching initials appear in the center of the screen. The ranking (from 1 to 99) for the last player(s) appears under the high score table.
© MCMLXXx ATARI appears three lines from the bottom of the screen. Next, if the 2-game option is selected, BONUS EVERY 20,000 alternates with 2 CREDIT MINIMUM. Credits and game price appear on the bottom line of the screen.
Finally, at the top of the screen, the words /N- SERT COINS and GAME OVER alternate if there are no game credits. The words PRESS START and GAME OVER alternate if there are game Credits.
A second picture, lasting for 12 seconds, is the TEMPEST logo. in this sequence, a multicolored square shrinks toward the center of the screen where a very small TEMPEST logo appears. The word TEMPEST enlarges in multiple images and changes color. In addition, © MCMLXXX ATARI appears on the lower half of the screen. The next picture, lasting from 5 to 60 seconds, shows the last game score, the highest score and its initials, and the words PRESS START or INSERT COINS alternating with GAME OVER at the top of ihe screen. Credits, game price, and bonus-life information are at the bottom of the screen. In the center of the screen, the picture duplicates a typical game-play sequence with the computer controlling the shooter.
The shooter rotates on ihe end of the tubelike surface that is nearest to the player. Enemies land on the end of the tube that is farthest away from the player and climb toward the shooter. The shooter fires down the tube ai the approaching enemies. This scene ends when either the shooter gets shot or spiked or when the shooter kills all the enemies and blasts through the tube into space, and lands on the next playfield.
If aplayer has credits and spins the control-panel knob, the attract mode ends and the words PRESS START appear in the center of the screen. Above this is the score from the last game and the highest score and its initials. Below the words PRESS STAAT are credits, game price and bonus life information.
If you select the 2-credit minimum option and a player inserts enough money for one credit, the messages JNSERT COINS and 2 CREDIT MINIMUM appear in the center of the screen until sufficient coins are inserted for game play.
- Ready-to-Play Mode “~S This mode begins when sufficient coins are accepted for a game. Each player rates himself by rotating the control knob. The knob moves a square which frames the level he wishes to select. The surface shape and bonus points for that level are also shown on the screen.
Bonus point incentive encourages play at a higher level, once that level has been reached. For example, starting at level one and playing through level nine awards 34,000 points. Starting at level nine and playing through that level awards 59,000 points. If a player reaches a higher level, he may continue to play near that level by pressing start before the attract mode is over. For example, if a player ended his last game in level 20, he may choose level 1, 3, 5, 7, 9, 11, 13, 15, or 17.
The ready-to-play mode ends when any pushbutton is pressed or 10 seconds elapse.
- Play Mode
In the play mode, a player-controlled, yellow clawlike shooter moves around on a three-dimensional tubelike playfield. The shooter rotates on the end of the tube that is nearest to the player. Enemies land on the end of the tube that is farthest away from the player to climb toward and attack the shooter. The shooter fires down the tube at the approaching enemies. When a player kills all the enemies on a tube, he blasts through the tube, flies through space, lands on anew tubelike playfield, and fights the enemies on that playfield. A player scores points by shooting enemies and by blasting through the tube to a new level. The player toses a life when killed by the enemy. The game is over when all the player's lives are gone.
All action occurs on one of sixteen suspended tubetike playtields. The three-dimensional tube surfaces are viewed from the top, so the view of the first playfield (a circle) is like looking into a well. Each playfield is made of 16 rails which connect the nearest to the farthest rim. The playfield color changes every 16 levels: level 1 is blue, level 17-red, level 33-yellow, level 49-cyan, 65-invisible and 81-green. Tempest ™/Cabaret™
ae “RES, FY BE
In addition, other events cause playfield color variation. The sheoter causes the two rails on which it sits to change color. Superzap causes the Playfield to flash as enemies are zapped. Playfield rails flash rainbow colors when a player earns a bonus life. Pulsar enernies cause sections of the nearest rim to disappear, and during the pulse phase, adjacent rails to flash.
The player's shooter is controlled by rotating the control-panel knob. The shooter moves around on the nearest rim of the tubelike playfield. The ends of the shooter always touch two adjacent rails. The rails on which the shooter sit change color (yellow in levels 1-16) which gives a flashlight effect and helps the player see the enemies in his lane.
A player shoots by pressing the fire button: tap it for one or two shots or press it for all eight shots. A shot is extinguished when it hits an enemy, after it passes the far rim or after it plows a certain distance into an enemy spike. A shot is renewed after it is extinguished so there may be a maximum of eight shots on the screen at one time.
A player may use two superzaps per level. A first superzap kills all enemies on the playfield at the time of firing. A second superzap randomly kills one enemy on the playfield. The superzap does not affect enemy shots, spikes or enemies not yet landed on the playfield. Superzap is recharged when the player blasts to a new level.
The following hints will help in game play: @ Players should work their way up through the levels to become familiar with game play. Drop down a level if play is too difficult. @ Experienced players should start at highest level possible for maximum points. @ On anew playfield shoot at enemy dots at far rim. @ Shoot the flipper at the top as soon as it Starts to flip. @ Use long spikes to reciaim shots and kill enemies {at the top) approaching you from adjacent Janes. @ Avoid shooting fuseball-tankers near the top since emerging fuseballs usually zip up to the top and kill you. @ Use Superzap right before last enemy reaches the top for a few extra points.
Tempest™/Cabaret ™
Enemy Flipper — Py
Tanker
Spiker
Spike
Fuseball
Pulsar ’
©
WANA Enemies in the Tempest”/Cabaret™ Game
Description
Originates at far rim and rides up two fails. Flips in the tube and on near rim. Kills player by flipping onto shooter or by shooting him. Player kills flipper by shooting when it is in the tube or when it is “standing” up. Or use Superzap. Originates at far rim or from a spiker. Rides between rails. Carries one or two flippers, fuseballs, or pulsars and expels these when shot or near rim. Kills player by shooting him. Player kills by shooting tanker in the tube. Or use Superzap. Originates at far rim. Rides up between rails on spike which it builds. Kills player by shooting him. Player kills by shooting it. Or use Superzap. Originates at far rim and builds up toward near rim. Kills player on contact. Player kills by shooting one or more times. Originates at far rim of from Tanker. Quickly rides on one rail, jumps to next rail and seeks out shooter. Kills player on contact. Player kills by shooting when fuseball is jumping between rails. Or use Superzap. Originates at far rim or from Tanker. Rides up and down ‘on two rails. Flips in the tube and on near rim and seeks out shooter. Kills if player is on same rails when it pulses, flips onto or shoots player. Player kills by shooting pulsar in the tube. Or use Superzap.
- High Score Initial Mode This mode begins when a player has one of the eight top scores. First, there is a fireworks display. Next, the high score table appears. Finally, a player enters his initials directly into the table following the instructions at the bottom of the screen. The initials and score are highlighted in a special color. You may bypass this mode by pressing the start button.
All but the three highest scores are erased whenever you enter the self-test mode, or press the RE- SET button on the game PCB, or turn off the power. This resetting replaces the five lowest scores with fictitious scores and initials.
If you change game options, lives per game, bonus level or difficulty, or if you erase the special “permanent” memory, the high score table is replaced with eight fictitious scores and_ initials. Therefore, the table will always be displayed on the screen, possibly consisting of one or more real scores and players’ initials. First Level Appears
W Points for Kill
250, 500, 750
Maintenance and Kepair
All games require certain maintenance to keep them in good working order. Clean, properly maintained games will attract players and earn more profits.
The most important maintenance item is running the self-test every time you collect money from the coin box. Just looking at a game will not tell you if the encoder wheel, light-emitting-diode switches or leaf switches are broken, or if LEDs have burned out. The self-test will inform you of any of these possible problems.
Second, you should regularly clean the outside of the game and the coin mechanisms. In addition, you will need to regularly clean the leaf switch contacts—or lubricate the encoder wheel: for details see this chapter.
Tempest™/Cabaret™
A. Cleaning
The exterior of the game cabinet and ithe metal and acrylic surfaces may be cleaned with any nonabrasive household cleaner. If desired, special coin machine cleaners that leave no residue can be obtained from your distributor.
Do not dry-wipe any of the acrylic panels, because dust can scratch the surface and result in fogging the plastic. The large monitor shield is made of tempered glass and the attraction panel is made of polycarbonate laminated to tempered glass. Both surfaces should be scratch-resistant and easy to maintain.
B. Fuse Replacement
This game contains six fuses—all on the power supply assembly (not including the monitor fuses). Replace fuses only with the same type as listed in Figure 25 of this manual. See the color X-Y monitor manual, TM-183, for the monitor fuse data.
Cc. The Control Panel
Prior to repairing or replacing any switch on the control panel or prior to removing the monitor, unplug the game. Then open the coin door.
Reach through the opening and open the luggage-style latch, located at each end on the underside of the control panel (see Figure 10). Close the coin door. Lift up on the control panel at the topmost edge and tilt it toward you.
The control panel edge next to the monitor shield has foam tape applied to it. This tape acts as a cushion for the glass and prevents spilled liquids from entering the cabinet interior. Always make sure this iape is in good condition.
When reinstalling the switches or encoder wheel, reconnect the harness wires as shown in Figure 11. Make certain the right colors go to the tabs on the switches.
LEAF SWITCH To Remove LED Switch: @ Remove all wires from the faulty switch. @ Turn the switch counterclockwise while holding the black cone-shaped bushing on the outside of the control panel. @ Install a new switch using the reverse procedure. Reconnect the harness wires.
TURN NUT TO RE- MOVE BLACK BUTTON
Figure 10 Opening the Control Panel and Replacing Switches
ENCODER: WHEEL PCB: BLUE, RED, BLACK & VIOLET WIRES
FIRE AND ZAP SWITCHES: 2 WIRES MAY BE HOOKED UP EITHER WAY
Figure 11 Tempest™/Cabaret™
1-PLAYER START SWITCH
WHITE WHITE/BLACK STRIPE RED BLACK
2-PLAYER START SWITCH
Control Panel Wiring
- Leaf Switch Replacement
The leat switches operate on 5 volts at a very low current. Therefore, pitting of these switches would be extremely rare. Probably the only reason that pitting would occur is very high-humidity.
Don’t bumish the switch contacts. To clean the cross-bar contacts, wipe them with a non-abrasive surface. A business card works very well.
To replace a leaf switch, remove the screw with a Phillips-head screwdriver—see Figure 10.
If the black button needs to be replaced, turn the stamped nut with a wrench in a counterclockwise direction, as seen from the inside of the control panel. The black ring on the outside of the control panel should not spin, due to its design.
- LED Start-Switch Replacement The light-emitting diode (LED) switches on the control panel have a very low failure rate. In case a switch should ever be suspect, first test it per the description that follows. To replace the switch, refer to Figures 10 and 11.
@ Remove the wires from the suspected switch. ® Set multimeter to ohms scale. Set ohms scale to Rx 1, then zero the meter. @ Connect multimeter leads to appropriate LED switch contacts (see Figure 11 for designation of switch contacts and meter lead placement). @ Check contacts (push and release the switch button) for closed and open continuity. @ If tne contacts do not operate sharply or always remain closed or open, then replace the LED switch as outlined in Figure 10. Reconnect the wires as shown in Figure 11.
Tempest™/Cabaret™
Disassemble in the order indicated. (Circled numbers match the steps described below.)
Close the control panel. Remove the two set screws in the control knob. Open the control panel. Unplug the four-pin harness connector. Remove the carriage bolts that hold the encoder wheel frame to the control panel.
To Lubricate:
- Loosen the two socket-head screws that attach the hub to the shaft.
- Unsnap the bottom clip ring. Pull the shaft up and ‘cout of the irame being careful not to drop the flywheel.
- Lightly lubricate the washer and the two nylon bushings that snap into the top and bottom the the frame. Apply Nyogel 779 to a cotton swab for this process.
To Replace the Encoder Wheel:
- Remove the three socket-head screws that attach the top to the bottom flywheel.
- Remove the etched encoder wheel and replace it with a new one, Reassemble in reverse, making sure that you center the new wheel between the photosensor device.
PHOTOSENSOR
ENCODER WHEEL Figure 12 Encoder Wheel Maintenance and Repair — To Replace the Coupler PCB:
- Remove the two socket-head screws, lock washers and hex nuts that hold the coupier PCB to the frame. 7 Remove the coupler PCB and repair as needed.
- Encoder Wheel Maintenance and Repair The encoder-wheel control requires lubrication of its bushings approximately every 10,000 credits and as you deem necessary. To lubricate or repair the control, remove the control from the control panel and disassemble it as illustrated in Figure 12. For \ubrication, use only Nyogel 779 lubricant (Aiari part no. 178027-001) on the two bushings of the encoder-wheel control.
For further instructions on how to replace the coupler PCB or the encoder wheel, see Figure 12.
D. Video Display Kemoval
The following procedure should only be performed by a qualified service technician.
To remove the color X-Y display, follow steps 1 through 6 listed below. Refer to Figure 13.
- Unplug the game. Open the control panel as described in Section C, Opening the Control Panel.
- Remove the display shield retainer at the top of the display shield. Unscrew the three Allen-head screws that secure the display shield retainer to the game cabinet. Lift out the tempered glass display shield.
- Carefully remove the staples that secure the cardboard bezel and remove the bezel. As an extra precaution, we highly recommend you discharge the high voltage from the picture tube.
- Open the rear access panel and unplug the 15-pin display harness connector. Unfasten the display chassis from the display bracket.
- Remove the four sets of hardware that secure the display frame to the wood frame.
- Carefully pull the display chassis out the front of the game.
Disassemble in the order indicated. (Circled numbers match the steps above.)
Figure 13
Video Display Removal
Tempest™ Cabaret™
E. Fluorescent Tube Replacement
To replace the white fluorescent tube behind the front graphics attraction panel, follow this procedure (see Figure 14):
- Unpiug the game from the wail outlet. Open the control panel (see Section C. The Contro/ Panel). To remove the fluorescent tube, remove the cardboard locking tab at each end of the tube. Slightly rotate the tube up or down, and carefully remove it from the lampholders. Replace with a new tube. Do not snap the tube in vigorously—you may break it, causing an implosion! Replace the locking tabs. Check that the green ground wire is securely attached to the metal lamp bracket and the ballast transformer on the wood panel. If the tube is not grounded, it may not start.
Figure 14 Fluorescent Tube Replacement
F. Printed-Circuit Board Kemoval
You may wish to remove the Analog Vector-Generator printed-circuit board (PCB), Auxiliary PCB or the Regulator/Audio Il PCB for service or inspection. To do this, refer to Figure 15 and proceed as follows:
- Open the rear access panel.
- Locate the hardware that secures the PCBs to the cabinet, and remove this hardware. (The Regulator/Audio || PCB has two screws and two washers. There is a mounting bracket that attaches the game PCBs to the cabinet wall. Remove the screw that attaches this bracket to the cabinet wall.)
- If you are removing the game boards, first remove the two machine screws or tie wraps that fasten the edge connectors to the game PCBs. Then unplug the edge connectors on the game PCBs. If you are removing the Regulator/Audio II PCB, disconnect the five small harness connectors on this board.
- Carefully slide the PCBs straight out of their slots. The Analog Vector-Generator and Aux- Tempest™/Cabaret™
iliary PCBs slide out together. Be careful not to twist the boards, as this may loosen connections or components. Replace or repair as required. Reinstall the PCBs, making sure that the connectors are properly plugged in. Note that they are keyed to fit on only one way, so if they don’t slip on easily, don’t force them! A reversed con: nector will probably damage your game and wil! void the warranty. Replace the hardware that secures the PCB to the cabinet wall. Reinstall the fasteners used to secure the edge connectors to the PCB. Close and lock the rear access panel. Check that the operation of the game is correct and perform the self-test. This is especially important with any game when you repair a PCB. Normally the only adjustments on this game are option switch changes (made on the 8-toggle DIP switch). Unless you are a qualified technician, do not turn any of the knobs near the game PCB’s edge connector. Also do not turn the small knobs on the Regulator/Audio Il PCB.
REGULATOR! AUDIO fl PCB
TEMPEST™ ANALOG VECTOR-GENERATOR PCB TEMPEST™ AUXILIARY PCB
Figure 15 Printed-Circuit Board Removal
Tempest ™/Cabaret™
G. Game Operation
With this manual you received three large sheets that contain the wiring and schematic diagrams for the Tempest™/Cabaret™ game. Sheet 1, Side A, includes information that shows the arrangement of these diagrams. These diagrams explain the functions of the circuits and define inputs and outputs.
In addition, you received the Tempest Troubleshooting Guide, which includes information on signature analysis, CAT Box tests and the memory map.
Atari's Tempest/Cabaret is a microprocessorcontrolled game. The microprocessor is contained on the game PCB. The game PCB receives switch inputs from the control panel and coin door. These inputs are processed by the game PCBs and output to the monitor, Regulator/Audio Il PCB, and control panel.
The color XY monitor receives signals for the X and Y axes and three color intensity signals (red, green and blue). Since the location of the beam in the monitor is controlled by the X- and Y-axis outputs of the game PCB, the game PCB does not contain a standard sync circuit. The X-and Y-axis inputs to the monitor step in increments of approximately 760 steps for the X (horizontal) axis, and approximately 1000 steps for the Y (vertical) axis. The three intensity signals control the brightness of the three electron guns (red, green and blue).
VIDEO DISPLAY
REGULATOR/AUDIO || PCB
POWER INTERLOCK SWITCH
ON/OFF SWITCH
le CONTROL PANEL
FLUORESCENT LAMP
COIN DOOR
ANALOG VECTOR- GENERATOR PCB
AUXILIARY PCB
POWER SUPPLY
Figure 16 Power Distribution
The Regulator/Audio Il PCB has three functions:
- it regulates the voltages from the power supply to +5 VDC, 2) it rectifies and filters +22 VDC, and 3) it amplifies the audio output from the Auxiliary PCB.
Specifically, the +5 VDC from the Regulator/Audio Il PCB provides most logic power to the Analog Vector-Generator and Auxiliary PCBs: + 22 VDC is regulated on the Analog Vector-Generator PCB to produce + 15; and +22VDC provides power for the audio output of the Auxiliary PCB. The audio output from the Regulator/Audio |! PCB directly drives the game speaker and is controlled by the volume con- Tempest “iCabaret™
trol, mounted inside the coin door on the utility switch panel.
The power supply is the source of all voltages in the game. These voltages are protected by five fuses in the fuse block on the power supply chassis. The primary winding of the power supply transformer is protected by the cartridge-type fuse in the power supply chassis.
Figure 16 illustrates the distribution of power in this game. Figure 17 illustrates the distribution of signals.
VIDEO DISPLAY
REGULATOR/AUDIO Il PCB
UTILITY SWITCH PANEL Yowume oyy —-\ ‘SPEAKER =D)
[ SLAM SWITCH
Kk)
ZNIOD CONTROL PANEL
‘COIN DOOR
ANALOG VECTOR. GENERATOR PCB Stam @
STARTLED 1&2 STAATI£2
ENCOOER WHEEL DIR & CLK
FIRE. ZAP.
AUXILIARY PCB
Figure 17 Signal Distribution
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Illustrated
Parts Lists
This chapter provides the necessary information for you to order replacement parts for this game. Please note that, for simplicity, common hardware has been deleted from most of these parts lists. This includes screws, nuts, washers, bolts, etc.
The parts lists are arranged in alphanumeric order. For example, all “A-” prefix numbers come first. Following these are numbers in sequence evaluated up to the hyphen, namely 00- through 99-, then 000598- through approximately 190000-.
When ordering parts from your distributor, give the part number, part name, applicable figure number of this manual, and serial number of your game. This will help to avoid contusion and mistakes in your order. We hope the results will be less downtime and more profit from your game.
Atari Customer Service numbers are listed on page vi for your convenience.
Tempest™/Cabaret™
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reprodusticn forbidden without the spe cific written permission of Atari, Inc., Sunnyvale, CA. This ring is only conditionally issued, and neither receipt ror possession thereof confers or transfers any right in, or Ir Cente to use, the subject matter of the drawing or any de- ‘sign cr technical information shown thereon, nor any fight to reproduce this drawing or any part thereof. Except for 037515-01 manulacture by vendors 9t tan) Ine., and for manufacture 3 *) Under the corporation's written license, no right is granted (Retaine: to reproduce this drawing or the subject mat‘er thereof, un: less by written agreement with or written permission from the corporation. 037517-02 (Bezel)
74-2110 (Lock) 037972-01 (Shield)
037993-02 (Rear Panel}
Control Panel Assy.— see Figure 19
Encoder Wheel— see Figure 20 037427-01 178013-004 . = (Foam Pad) (Latch)
037984-01 (Attract. Panel)
j Fluor. Light Assy.— 036891-01 see Figure 24 (Spkr. Grilte)
a Coin Door Assy.— see Figure 26 037895-01 (Graphics Decal)
178034-024 (FMotding)
A037983-01 (Cab't Assy.) 037491014 (Coin Box)
Figure 18 Cabinet-Mounted Assemblies A037974-xx A
Schematics, Self-Test Label & Manuals— see parts list on following page
: 92-053
(Video Display)
037529-01 (Bracket)
035745-03 (PCB Retainer)
034536-03 (Vibra. Damper)
Reg/Audio II PCB Assy.— see Figure 21
007882-02 (Inter. Sw.Cvr.)
A037450-01 (intert. Sw. & Brkt.)
A038017-01 (Pwr, Harness)
009992-01 (On/Off Sw.Cvr.)
‘A037470-01 (On/Off Sw.& Mnig. Plate)
A037453-03 A037454-03 A037455-03 or A037784-03 (Enclosure) Tempest™/Cabaret™
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyvale, CA. Tis drawing is only conditionally issued, and neither receipt nor possession thereo! confers or transfers any right in, oF li cense to use, the subject matter of the drawing or any de- Sign of technical information shown thereon, nor any right to reproduce this drawing or any part thereof. Except tor manutacture by vendors of Atari, Inc., and for manufacture under the corporation's written license, no right is granted to reproduce this drawing or the subject matter thereof, unless by written agreement with or written permission trom the corporation
038003-01 (Bracket) 19-9032 (Vol. Ctrl} 69-001 (SelfTest Sw.) 62.041 (Util. Coin Sw.) A002465-01 (Coin Counter) ‘A038004-01 (Vol/Selt-Test Harn.)
148001-001 (Speaker)
A007638-01 (Slam Switch)
A037851-01 (PCB Interctr.)
Analog Vector-Generator PCB Assy.— ‘see Figure 23
034536-05 (Vibra. Damper)
034536-02 (Vibra. Damper)
Auxiliary PCB Assy.— see Figure 22
037742.01 (Mounting Brkt) 721620S (Screw) Power Supply Assy.— 75-0717 (Fiber Washer) 75-99516 (Nut Wash. Assy.)
(Power Cord) Figure 18 Cabinet-Mounted Assemblies A037974-xx
Tempest™/Cabaret™ Figure 18 Cabinet-Mounted Assemblies, continued Parts List
Part No. Description A002465-01 Coin Counter A007638-01 Slam Switch Assembly
| A037450-01 | Interlock Switch/Bracket Assembly | (modified for safety) |
| A037453-03 | Strain-Relief Power Cord | (U.S. and Canada) |
A037454-03 Strain-Relief Power Cord (Austria, Belgium, Chile, Denmark, Finland, France, Germany, Greece, indonesia, Italy, Netherlands, Norway, Spain, Sweden, and Uruguay)
| A037455-03 | Strain-Relief Power Cord | (Australia and New Zealand) |
A037470-01 Power On/Off Switch/Mounting Plate Assembly A037491-01 Coin Box A037496-01 Coin Box Enclosure
| A037784-03 | Strain-Relief Power Cord Assembly | (United Kingdom, Ireland, Lebanon, Saudi Arabia, |
India, Hong Kong, Singapore, Egypt, Nigeria, Republic of South Africa, Zimbabwe) A037851-01 Printed-Circuit Board Interconnector A037983-01 Cabinet Assembly (includes legs and PCB retainers, but not the rear access panel) A038004-01 Harness for Volume Control/Self-Test Switch/Coin Counter Assembly A038014-01 Main Harness Assembly A038016-01 Power Harness Assembiy The following seven items are the technical information supplements to this game: DP-196-01, 02, 03 Tempest™/Cabaret™ Schematic Drawings (Sheets 1,2,3) ST-196 Tempest/Cabaret Label with Self-Test Procedure and Option Switch Settings TM-183 Service Manual for 19-Inch Wells Gardner Color X-Y Monitor TM-196 Tempest/Cabaret Operation, Maintenance and Service Manual T™M-195 Tempest Troubleshooting Guide 19-9032 Volume Control 62.041 SPDT Momentary-Contact Pushbutton Utility Coin Switch with Black Cap
| 69-001 | DPDT Self-Test Switch | (for British-made coin doors) |
| 71-2110 | Panel Cartridge Lock Mechanism | (for rear access panel) |
| 72-1620S | #6-32 x 1¥%-Inch Pan-head Screw | (to attach mounting bracket to main and auxiliary PCBs) |
| 728610S | #6 x %Inch Phillips-head screw | (to attach PCB mounting bracket to side panel) |
74-5608NN Spacer for Mounting Printed-Circuit Boards 75-07017 Washer for Mounting PCBs 75-99516 #6-32 Nut Washer Assembly
| 78-24012 | SInch Beaded Nylon Tie Wrap | (for game PCB edge connectors) |
78-3201 Cabinet-Leveling Leg 92-053 19-Inch Wells-Gardner Color X-Y Display 007882-02 Interlock Switch Cover 00999201 On/Off Switch Cover
| 034536-02 | Foam Vibration Damper | (goes between game PCBs) |
034536-03 Foam Vibration Damper (for Regulator/Audio |] PCB) 034536-05 Foam Vibration Damper (goes between main PCB and cabinet wall) 035745-03 10-Inch Plastic PCB Retainer 036686-01 Card of Game Pricing Labels. 036891-01 Speaker Grille 037243-01 Metal Base Plate (located underneath power supply) 037427-01 Rear Access Panel Foam Pad 037515-01 Top Monitor Shield Retainer 037517-02 Cardboard Monitor Bezel 037529-01 Monitor Support Bracket 037742-01 Game PCB Mounting Bracket 03797201 Monitor Shield 037984-01 Attraction Panel with Graphics 037993-02 Rear Access Panel (does not include lock) 037995-01 Side Panel Graphics Decal 038003-01 Bracket for Volume Control, Self-Test Switch and Coin Counter(s) 148001-001 6 x BInch 4-0hm 15W Oval High-Fidelity Speaker 178013-001 Spring Oraw Latch 178034-024 %-Inch Black Plastic Molding
78-6900401 (Tape) 75-9418 (Nut)
Encoder Wheel Assy.— see Figure 20 Tempest ™iCabaret™
75-010S NOTICE TO ALL PERSONS RECEIVING THIS DRAWING ecnen 73-834 CONFIDENTIAL: Reproduction forbidden without the spo ike writen permisson of Atari inc., Sunnyvale, GA, This (Knob) drawing is only conditionally issued, and neither receipt nor ‘A037976-01 posbenbon thers corer or ransfere ay ng ot Gense to use. the subject matter of the drawing or any de (Control Panel) 75-5108 sian or technical infomation shown thea, norany rant 0 reproduce this drawing or any part tnereot. Except for (Bolt) manufacture by vendors: ‘St Atari, Inc., and for manufacture Under the corporation’ wit cerse no nah ts grated (reproduce this drawing or the subject matter thereot, un 75.9910NO 62039 ( lees by written agreement with or written permission from ©) Re aheaten ~ (LED Switch) 178030-003 (Pushbtn Assy.)
036895-01 D (Sw. Bezel) . 033127-01 (Bushing)
75-9910W0 (Nut)
75-0178,
Figure 19 Control Pane! Assembly A037977-01 A
Parts List
Part No. Description
A037976-01 Control Panel with Graphics A038018-01 Conirol-Panel Harness 62-039 SPDT Momentary-Contact Pushbutton Start Switch with Red Light-Emitting Diode 73-834 Control Knob with Skirt 75-010S #10 Flat Washer for Encoder Wheel Control 75-918S, #8-32 Polymer Hex Nut 75-941S, #10-24 Polymer Lock Nut 75-5108B #10-24 x %-Inch Carriage Bolt 75-9910NO #911 Steel Stamped Nut 78-6900401 Vinyl Foam Single-Coated-Adhesive Tape, %4-inch wide x /,-inch thick (19 in. required) 036895-01 Black Molded Switch Bezel * 037973-01 Control Panel 037975-01 Control Panel Decal 160013-001 Leaf Switch and Button Holder (leaf switch only is part no. 160012-001) 178030-003 Black Pushbutton Assembly
“If not available, the following may be used: 75-017S Yeinch Steel Flat Washer 75-9910W0 Stamped Nut 033127-01 Black Molded Switch Bushing
Tempest™/Cabaret™
Opn
036735.01 (Shaty
Not Shown— Nyogel 779 lubricant (178027-001) 75-07047
76-080401 (Bushing)
72-8406 (Screw)
Gx___sa 2.002 (Ring)
A035220-02 (PCB Assy.)
75-0448 75-9145 (Washer (Nut) 036798-01 (Encoder Wheel)
I
NOTICE 0 ALL PERSONS RECEIVING THIS DRAWING. CONFIDENTIAL: Reproduction forbidden without the spe Gific written permission of Atari, Inc., Sunnyvale, CA. This Srawing is only conditionally issued, and neither eceipt nor possession thereof confers or transfers any right in, oF hi Cense to use, the subject matter of the drawing or any de sigh oF technical information shown thereon, nor any right t0 reproduce this drawing or any part thereo!. Except for manulacture by vendors of Atati,inc., and to: manufacture Under the corporation's wntten license, no right is granted to reproduce this drawing oF the subject matter thereol, un less by written agreement vith or wntien permission {rom the corporation —, (Frame) NK 73-834 (Knob)
036794-01
036796-01 (Flywheel)
036797-01 (Flywhee! Cap)
Figure 20 Encoder Wheel Assembly A037781-01 A
Tempest™/Cabaret™
Figure 20 Encoder Wheel Assembly Parts List
Part No. Description A035220-02 Coupler PCB Assembly A036096-01 Harness Assembly 72-8406 #4-40 x }-Inch Hex Socket-Head Cap Alloy Steel Machine Screw 73-834 Control Knob 75-044S #4 Zinc-Plated Steel Split-Lock Washer 75-07047 Nylon Washer 75-9145 #4 Hex Socket-Head Cap Steel Machine Nut 76-080401 Dual Shoulder Radiat Polymer Bushing 036794-01 Frame 03679501 Shait 036796-01 Top Flywheet 036797-01 Bottom Flywheel Cap 036798-01 Etched Encoder Wheel 178012-002 “Klip-Ring” Retaining Ring 178027-001 Nyogel 779 Lubricant
Tempest™/Cabaret™
| 3300 | + | c23 | cst |
| 35V | Q | Git} | feeb |
qe} 422}
| p52 | R25 | ie | {22 |
| C5 | {405 | C220, | CRA |
Sek 8 O9 pes ____ 7812 7905
| Oo | Nee | —[pes 1a rw | Oo |
Zz
| _ | UP 32 | TOAZ002ZA | TT DAZO02A |
SIO? Nacd2 05 Q7 7
| ce? | OTT | 1 | a | faa |
RSet lo RS ral ee) ce raahe
| BIR | fl, | CoGEZ | cst |
| g | cetaa | ]=|e | Reego |
RZ TOK cla 220 [ R21, ew
Figure 21 A035435-02 E NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific wnitten permission of Atari, Inc., Sunnyvale, CA. This ‘drawing is only concitionally issued, and neither receipt nor possession thereof confers or transfers any right in, or liense to use, the Subject matter of the drawing or any de sign or technical information shown thereon, nor any right to reproduce this drawing or any part thereof. Except for manufacture by vendors of Atari, Inc., and for manufacture under the corporation's written license, no right to reproduce this drawing is granted or the subject matter thereof unless by written agreement with or written permission from the corporation.
Regulator/Audio I! PCB Assembly
Tempest ™iCabaret™
Figure 21 Regulator/Audio I! PCB Assembly Parts List
Part No. Description (Reference Designations and Locations in Bold)
| 12-52P7 | 2.7 Ohm, +5%, 1W Resistor | (R5) |
16-54P0 4 Ohm, +5%, 5W Wirewound Resistor (R25) 19-100P 1015 -1 Ohm, +3%, 7W Wirewound Resistor (R24)
| 19-315102 | 1K Ohm Vertical PCB-Mounting Cermet Trimpot | (R8) |
| 24-250108. | 1000 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor | (C13) |
24-250477, 470 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C1, 4, 12)
| 24-350226 | 22 uf Aluminum Electrolytic Fixed Axial-Lead 35V Capacitor | (C24, 31) |
24-350338, 3300 uf Aluminum Electrolytic Fixed Axial-Lead 35V Capacitor (C9, 10, 18, 19) 24-500105, 1 uf Aluminum Electrolytic Fixed Axial-Lead 50V Capacitor (C22, 23)
| 29-088 | -1 uf Ceramic-Disc 25V Radial-Lead Capacitor | (C3, 11, 20, 21) |
| 31-1N4002 | 100V 1-Amp. Silicon Rectifier Type 1N4002 Diode | (CR1, 4) |
| 31-1N5401 | 100V 3-Amp. Silicon Rectifier Type 1N5401 Diode | (CRS5-8) |
| 33-TIP32 | PNP Power Transistor, Type TIP32 | (Q2) |
| 34-2N3055 | NPN Silicon Transistor, Type 2N3055 | (Q3) |
| 37-LM305 | 5V Linear Voltage Regulator | (Q1) |
| 37-7812 | +12V Voltage Regulator, Type 7812 | (Q8) |
| 37-7905 | — 5V Voltage Regulator, Type 7905 | (Q9) |
72-1608C 46-32 x ¥2-Inch Cross-Recessed Pan-Head Corrosion-Resistant Steel Machine Screw 72-6806S #6 x %-Inch Pan-Head Thread-Forming Cross-Recessed Type-AB Zinc-Plated-Steel Screw (Q8) 75-F60405 #6-32 x V4-Inch Binder-Head Nylon Screw (Q5, 7) 75-99516 #6-32 Nut/Washer Assembly
| 78-16008 | Thermally Conductive Compound | (Q3) |
78-16014 Thermally Conductive Silicon Insulator (Q2, 9)
| 79-58306 | 6-Position Connector Receptacle | (J6, 9) |
| 79-58308 | 9-Position Connector Receptacle | (J7) |
| 79-58346 | 12-Position Connector Receptacle | (J10) |
| 79-58354 | 4-Position Connector Receptacle | (J8) |
020670-01 Test Point 034531-01 Heat Sink
| 100015-103 | .01 uf Ceramic-Disc 25V Radial-Lead Capacitor | (C5, C14) |
| 110000-010 | 1 Ohm, +5%, 1%4W Resistor | (R10, 19) |
110000-100 10 Ohm, +5%, YW Resistor (R11, 20, 29, 30)
| 110000-101 | 100 Ohm, +5%, %W Resistor | (R4, 12, 22) |
| 110000-102 | 1K Ohm, +5%, %4W Resistor | (R27, 28) |
110000-103 10K Onm, +5%, %W Resistor (R13, 14)
| 110000-271 | 270 Ohm, +5%, %W Resistor | (R1) |
| 110000-330 | 33 Ohm, +5%, %W Resistor | (R3) |
110000-392 3.9K Ohm, +5%, %4W Resistor (R6) 110000-562 5.6K Ohm, +5%, %W Resistor (R32, 33) 110000-752, 7.5K Ohm, +5%, Y4W Resistor (R7) 110001-221 220 Ohm, +5%, v2W Resistor (R9, 21) 116000-220 22 Ohm, + 5%, 10W Wirewound Resistor (R31) 122002-102 .001 uf Ceramic-Disc Minimum 25V Radial-Lead Capacitor (C2, 7, 16) 122004-224 .22 uf Ceramic-Disc 25V Capacitor (C6, 8, 15, 17)
| 437151-002 | Type TDA2002A 8W Linear Audio Amplifier Integrated Circuit | (Q5, 7) |
Tempest™/Cabaret™
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without tne spe Citic written permission of Atari, Inc., Sunnyvale. CA. This drawing is only conditionally issued, and neither receipt nor possession thereof confers or transfers any right in, or t- Conse to use, the subject matter of the drawing or any de sign or technical information shown thereon, nor any right to reproduce this drawing or any part thereof. Except for manufacture by vendors of Atari, Inc., and tor manufacture Under the corporation's written license, no right to reproduce this drawing is granted or the Subject matter thereof Unless by written agreement with or written permission from the corporation
Ros zs
m2? + 22
ez
esr
(=? ge5
<r
(stets
Ry Sie 4 i
6212294-0)
| areos-os1 | casi | (cei | [eet | BE |
rete TIE} samtuird
| f | Bab | PETE! | ore23 | {Gor cae |
| sch | (Ls7e§ | usis7§ | ||
| eol2294 -o1 | Cohez# | cas | Gos | |, |
ye
| (eax I | iso} | us7ah | UL |
q Lear 4 Lsi3e 6 fe Rade ; an | io 3 a4 Ta u RRR
1 2 3 4 5 6
Figure 22 Tempest™ Aux A037585-01 ry PCB Assembly B
Tempest ™iCabaret™
Figure 22 Tempest™ Auxiliary PCB Assembly Parts List
Part No. Description (Reference Designations and Locations in Bold) C012294-01 Audio VO N-Channel MOS/LSI Custom Chip (B/C2, C/D2) 21-101153 .015 yf, + 10%, Radial-Lead Epoxy-Dipped 100V Mylar Capacitor (C9, 10) 24-250107 100 pf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C56) 24-250476 47 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C13) 24-250477 470 ut Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C37, 38) 24-500105 1 uf Aluminum Electrolytic Fixed Axial-Lead 50V Capacitor (C31, 32, 45-47) 24-500476 47 uf Aluminum Electrolytic Fixed Axial-Lead 50V Capacitor (C19-21) 29-088 -1 uf Ceramic-Disc Radial-Lead 25V Capacitor (C1-8, 11, 12, 14, 15, 17, 18, 22-30, 33-36, 39-44, 49-55) 31-1N100 100V Type-1N 100 Switching Diode (CR3, 4) 37-LM324 Type-LM324 Integrated Circuit (K3, K6) 37-4584B Type-4584B Integrated Circuit (E6) 37-74109 Type-74109 Integrated Circuit (A2) 37-74LS00 Type-74LS00 Integrated Circuit (04) 37-74.S02 Type-74LS02 Integrated Circuit (Ja) 37-74LS10 Type-74LS10 Integrated Circuit (C5) 37-74LS14 Type-74LS14 Integrated Circuit (F4) 37-74LS32 Type-74LS32 Integrated Circuit (C4) 37-74LS874 Type-74LS74 Integrated Circuit (C6, D5) 37-74LS139 Type-74LS139 Integrated Circuit (B4, B5) 37-74LS157 Type-74LS157 Integrated Circuit (D6) 37-74LS161 Type-74LS161 Integrated Circuit (C1, D1) 37-74LS174 Type-74LS174 Integrated Circuit (A3, H4) 37-74LS175 Type-74LS175 Integrated Circuit (J3) 37-74LS191 Type-74LS191 Integrated Circuit (A4) 37-74LS244 Type-74LS244 Integrated Circuit (E3, H3) 37-74LS374 Type-74LS374 Integrated Circuit (B1, F3) 37-74808 Type-74S08 Integrated Circuit (E4) 38-MV5053 Type-MV5053 Red Light-Emitting Diode (CR1) 66-114P1T 4-Station, Single-Throw, Dual-Inline-Package Bit Switch (D/E2) 79-42C16 16-Contact Medium-Insertion-Force Integrated Circuit Socket (A1, E1, F1, H1, J1, K1, 11) 79-42022 22-Contact Medium-Iinsertion-Force Integrated Circuit Socket (C3) 79-42C40 40-Contact Medium-Insertion-Force Integrated Circuit Socket (B/C2, C/D2, E2, FiH2, J2, K/L2) 020670-01 Test Point 110000-102 1K Ohm, +5%, YW Resistor (R1, 5, 7, 41, 45, 53-58, 64, 66-70) 110000-103 10K Ohm, +5%, %4W Resistor (R3, 4, 8-26, 36, 48-52) 110000-104 100K Ohm, +5%, YW Resistor (R35, 37, 38) 110000-151 150 Ohm, +5%, %W Resistor (R2, 30, 31) 110000-221 220 Ohm, +5%, 4W Resistor (R65) 110000-223 22K Ohm, +5%, %4W Resistor (R34) 110000-332 3.3K Ohm, +5%, Y4W Resistor (R39, 40, 46, 47) 410000-334 330K Ohm, +5%, %W Resistor (R32, 33) 110000-471 470 Ohm, +5%, ‘4W Resistor (R42-44, 59-63) 110000-472 4.7K Ohm, +5%, VW Resistor (R29) 110000-473 47K Ohm, +5%, v4W Resistor (R6, 28) [Continued on next page]
Tempest ™/Cabaret™
Figure 22 Tempest™ Auxiliary PCB Assembly, continued Parts List
Part No. Description (Reference Designations and Locations in Bold)
| 110001-102 | 1K Ohm, +5%, Y2W Resistor | (R27) |
122005-193 .01 uf Ceramic-Disc 25V Radial-Lead Capacitor (C16) 128002-102 1000 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor (C48)
| 131003-001 | Type-1N5257B Zener Diode | (CR2) |
| 136002-126 | Programmable Read-Only Memory | (A1) |
| 136002-127 | Programmable Read-Only Memory | (E1) |
| 136002-128 | Programmable Read-Only Memory | (F1) |
136002-129 Programmable Read-Only Memory (H1)
| 136002-130 | Programmable Read-Only Memory | (J1) |
| 136002-131 | Programmable Read-Only Memory | (K1) |
| 136002-132 | Programmable Read-Only Memory | (L1) |
| 137002-001 | Type-74S86 Integrated Circuit | (E5) |
| 137003-001 | Type-74S03 Integrated Circuit | (F5) |
137004-001 Transistor Array (E2, FIH2, J2, K/L2)
| 137161-001 | Read-Only Memory | ER2055 | (C3) | Note: /f you replace this part, you must erase this ROM |
before locking up the game. See Figure 6, Self-Test Procedure, in this manual for instructions. If you do not erase the ROM, the self-test will show the ROM to be “defective” by displaying the letter E on the screen. 179014-012 12-Pin Polarized PCB Header (J16, J17)
Tempest ™/Cabaret™
¥e x DETAIL att Roprodueten
oe 3 Use IC pads enclosed with dotted Site wntien permission of A
Ege £ lines when inserting 74L$245, The
go 3 other pads are for inserting an 8304B
33 e 33 at locations F2, H2, and H3. 233 23 gig 22 T oe00000000, to ges = 1 13008000000 the coy 8 =5 38 uw 0 8 ze, 82 Big SucEss SSacze 28 te 4 Pa noone & L 20095905903 ®2_ S29e8ke ogeNae 82 0000000000 aes ee ___s_8 Install W3 and W4 for -01, -02 PCB
238 9 assemblies
38 7 s Install W1 and W2 for -03, 04 PCB set 3 assemblies BBs
ie Figure 23 Tempest™ Analog Vector-Generator PCB Assemb! B+ A037383-01 thru -04
Tempest™/Cabaret™
Figure 23 Tempest™ Analog Vector-Generator PCB Assembly, continued Parts List
Part No. Description (Reference Designations and Locations in Bold)
19-315103 10K Vertical PCB-Mounting Cermet Trimpot (R147, 150, 167, 168) 19-315201 200 Ohm Vertical PCB-Mounting Cermet Trimpot (R117, 118) 19-315202 2K Ohm Vertical PCB-Mounting Cermet Trimpot (R165, 169) 21-101103 .01 uf, + 10%, Radial-Lead Epoxy-Dipped 100V Mylar Capacitor (For -02 & -04 PCB assy. only: C63)
24-250107 100 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C57-59) 24-500105 1 uf Aluminum Electrolytic Fixed Axial-Lead 50V Capacitor (C61, 62) 27-102182 0018 pf, + 10%, Radial-Lead Ceramic-Disc 1000V Capacitor (For -01 & -03 PCB assy. only: C67) For -02 & -04 PCB assy. only: C75) 29-006 1 uf, + 10%, 35V Tantalum Capacitor (C60)
29-088 .1 pf Ceramic-Disc 25V Radial-Lead Capacitor (C1-19, 22-49, 51, 53-55, 69, 71, 77-80, 82-85, 88-91, 93-97, 99, 102, 103.) Also, for 01 & -03 PCB assy. only: C66, 68, 72, 73. For -02 & -04 PCB assy. only: C64, 65, 74, 76)
| 31-1N100 | 100V Type-1N100 Switching Diode | (CR4) |
| 31-1N914 | 75V Type-1N914 Switching Diode | (CR1) |
33-2N3906 Type-2N3906 PCB Switching and Amplifying Transistor (Q9-11) 34-2N3904 Type-2N3904 NPN 60V 1-Watt Transistor (Q1-4, 8, 12) 34-2N6044 Type-2N6044 Darlington NPN Transistor (Q5, 7)
| 37-TLO82CP | Type-TL082 Integrated Circuit | (A11, D11, D/E12, D/E13, K11) |
| 37-1495 | Type-MC1495L Integrated Circuit | (A/B12, A/B13, C12, C13) |
| 37-13201 | Type-LF13201 Integrated Circuit | (B11, E11) |
| 37-74LS00 | Type-74LS00 Integrated Circuit | (K9) |
| 37-74LS02 | Type-74LS02 Integrated Circuit | (A7, B5) |
| 37-74LS04 | Type-74LS04 Integrated Circuit | (J11) |
| 37-74LS08 | Type-74LS08 Integrated Circuit | (A4) |
| 37-74LS10 | Type-74LS10 Integrated Circuit | (F4) |
| 37-74LS14 | Type-74LS14 Integrated Circuit | (E6) |
| 37-74LS20 | Type-74LS20 Integrated Circuit | (E9) |
| 37-74LS27 | Type-74LS27 Integrated Circuit | (B6) |
| 37-74LS32 | Type-74LS32 Integrated Circuit | (C3, J8, B9, R7) |
| 37-74LS42 | Type-74LS42 Integrated Circuit | (F7) |
| 37-74LS74 | Type-74LS74 Integrated Circuit | (B8, D3) |
| 37-74LS109 | Type-74LS109 Integrated Circuit | (A8) |
| 37-74LS139 | Type-74LS139 Integrated Circuit | (B3, C1, J2, J5, P7) |
| 37-74LS157 | Type-74LS157 Integrated Circuit | (K2,L2, M2, N2, P8) |
| 37-74LS161 | Type-74LS161 Integrated Circuit | (E4, C8, D8, E8, F8) |
| 37-74LS 164 | Type-74LS164 Integrated Circuit | (A9) |
| 37-74LS 174 | Type-74LS174 Integrated Circuit | (E7, H8, N8, N9) |
| 37-74LS175, | Type-74LS175 Integrated Circuit | (H7, J7, K8) |
| 37-74LS191 | Type-74LS191 Integrated Circuit | (J6, L8) |
| 37-74LS193, | Type-74LS193 Integrated Circuit | (K5, L5, M5) |
| 37-74LS194 | Type-74LS194 Integrated Circuit | (D5, D6, E5, F5, H5, H6) |
| 37-74LS244 | Type-74LS244 Integrated Circuit | (A/B1, B/C1, E2, M12, N12, R9) |
| 37-74LS245 | Type-74LS245 Integrated Circuit | (F2,H2,H3) Acceptable substitute is part no. 37-8304B. |
| 37-74LS273 | Type-74LS273 Integrated Circuit | (D9) |
| 37-74LS367 | Type-74LS367 Integrated Circuit | (K7, N7) |
| 37-74LS393 | Type-74LS393 Integrated Circuit | (B4, D4) |
[Continued on next page]
Tempest ™/Cabaret™
7 ™ . Figure 23 Tempest” Analog Vector-Generator PCB Assembly, continued Parts List
Part No. Description (Reference Designations and Locations in Bold) 37-74LS399 Type-74LS399 Integrated Circuit (H9) 37-74LS670 Type-74LS670 Integrated Circuit (K6, L6,M6) Acceptable substitute is part no. 37-74LS170. 37-74S00 Type-74S00 Integrated Circuit (F6) 37-74S02 Type-74S02 Integrated Circuit (C6) 37-74S04 Type-74S04 Integrated Circuit (A6, E3, N6) 37-74S08 Type-74S08 Integrated Circuit (F3) 37-74S74 Type-74S74 Integrated Circuit (B7, C7) 37-74S260 Type-74S260 Integrated Circuit (C5) 37-74193 Type-74193 Integrated Circuit (C4) 37-7815 + 15V Voltage Regulator (VR3) 37-7915 — 15V Voltage Regulator (VR1) 38-MV5053 Type-MV5053 Light-Emitting Diode (CR2) 41-3003 100 uH, + 10%, Hot-Molded Plastic Fixed R.F. Choke (L1) Acceptable substitute is part no. 141002-001. 62-001 SPST Momentary Pushbutton Switch (Reset) 66-114P1T 4-Station Single-Throw, Dual-Inline-Package Bit Switch (K10/11) 66-118P1T 8-Station Single-Throw, Dual-Iniine-Package Bit Switch (L12, N13) 78-13003 General Electric RTV #108 Sealing Compound 79-42C16 16-Contact Medium-Insertion-Force Integrated Circuit Socket (D7) 79-42C24 24-Contact Medium-Insertion-Force Integrated Circuit Socket (D1, E1, F1, H1, J1, K1, L/M1, MI/N1, P1, R1, N/P3, R3) 79-42C40 40-Contact Medium-Insertion-Force Integrated Circuit Socket (C2) 81-4302 Nylon Snap-In Fastener 90-6013 Microprocessor (C2) 90-7005 Random-Access Memory (P9) 90-7033 Random-Access Memory (J3, J4, K3, K4, L3, L4, M3, M4, P2, P4, R2, R4) 99-130430 Voltage-Dependent Resistor (RV1, 2) Acceptable substitute is part no. 110004-001. 110000-101 100 Ohm, +5%, %4W Resistor (R107, 111) 110000-102 1K Ohm, +5%, %4W Resistor (R3, 13, 15, 31, 32, 34, 35, 62-67, 81, 129, 142, 160) 110000-103 10K Ohm, +5%, %W Resistor (R1, 2, 4-12, 14, 16, 17, 38, 60, 61, 84, 87-102, 128, 134, 139, 156, 158. Also, for -01 & -03 PCB assy. only: 105, 106, 112.) Also, for any PCB assy. if you are using part no. 37-74LS170 in locations K6, L3, M6: R19-30) 110000-104 100K Ohm, +5%, %W Resistor (R42-49) 110000-122 1.2K Ohm, +5%, %4W Resistor (R40) 110000-151 150 Ohm, +5%, %W Resistor (R86) 110000-152 1.5K Ohm, +5%, %4W Resistor (R137) 110000-153 15K Ohm, +5%, %4W Resistor (R58, R130) 110000-221 220 Ohm, +5%, %W Resistor (R18, 85) 110000-222 2.2K Ohm, +5%, ¥4W Resistor (R37, 52, 54, 56, 131-133, 144, 153-155, 163)
110000-223 22K Ohm, +5%, YW Resistor (R36, 82) 110000-272 2.7K Ohm, +5%, V4W Resistor (R141, 157, 161) 110000-331 330 Ohm, +5%, YW Resistor (R51, 53, 55, 57, 74-76) 110000-392 3.9K Ohm, +5%, %W Resistor (R41, 110, 138, 143, 145, 162, 164) 110000-470 47 Ohm, +5%, %4W Resistor (R80) 110000-471 470 Ohm, +5%, YW Resistor (R68-73, 135, 136, 148, 151, 170, 173) [Continued on next page]
Tempest ™/Cabaret™
Figure 23 Tempest™ Analog Vector-Generator PCB Assembly, continued Parts List
Part No. Description (Reference Designations and Locations in Bold)
| 110000-472 | 4.7K Ohm, +5%, %W Resistor | (R39, 59, 77-79) |
| 110000-561 | 560 Ohm, +5%, %4W Resistor | (R127) |
110000-562 5.6K Ohm, +5%, ¥4W Resistor (R146, 166)
| 110000-681 | 680 Ohm, +5%, %4W Resistor | (R140, 159. | Also, for -02 & -04 PCB assy. only: R113) |
110000-682 6.8K Ohm, +5%, %W Resistor (R50) 110000-683 68K Ohm, +5%, %W Resistor (R83) 110000-821 820 Ohm, +5%, %4W Resistor (For -02 & -04 PCB assy. only: R103, 104, 114) 110001-271 270 Ohm, +5%, YeW Resistor (R152)
| 110003-752 | 7.5K Ohm, + 1%, ,W Resistor | (R108, 109, 115, 116, 119-126) |
110005-001 0 Ohm Jumper (W3, 4. For -03 & -04 PCB assy. only: W1, 2) Acceptable substitute is 24-gauge wire. . 121007-473 .047 uf, + 10%, Radial-Lead Epoxy-Dipped 50V Polycarbonate Capacitor (C100, 101) Acceptable substitute is part no. 121006-473. 122000-225 2.2 uf, + 10%, 35V Tantalum Capacitor (C56) 122005-103 .01 yf, Ceramic-Disc 25V Radial-Lead Capacitor (C70)
| 128002-100 | 10 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor | (C81) |
| 128002-101 | 100 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor | (C21) |
| 128002-151 | 150 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor | (C87) |
128002-221 220 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor (C52)
| 128002-390 | 39 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor | (C20, 86, 92, 98) |
| 131002-001 | __6.8V, 400 mW, +5%, Zener Diode | (CRS) |
136002-101 Programmable Read-Only Memory (D1) Acceptable substitute is part no. 136002-113. g
| 136002-102 | 3 | Programmable Read-Only Memory (E1) Acceptable substitute is part no. 136002-114. |
| 136002-103. | § | Programmable Read-Only Memory (F1) Acceptable substitute is part no, 136002-115. |
| 136002-104 | 3 | Programmable Read-Only Memory (H1) Acceptable substitute is part no. 136002-116. |
| 136002-105, | a | Programmable Read-Only Memory (J1) Acceptable substitute is part no. 136002-117. |
> 136002-106 aS -| Programmable Read-Only Memory (K1) Acceptable substitute is part no. 136002-118.
| 136002-107 | _ | Programmable Read-Only Memory (LIM1) | Acceptable substitute is part no. 136002-119. |
| 136002-108 | 5 | Programmable Read-Only Memory (M/N1) Acceptable substitute is part no. 136002-120. | |
| 136002-109 | 5 | Programmable Read-Only Memory (P1) Acceptable substitute is part no. 136002-121. | |
| 136002-110 | 3 | Programmable Read-Only Memory | (R1) Acceptable substitute is part no. 136002-122. |
| 136002-111 | Programmable Read-Only Memory | (N/P3) Acceptable substitute is part no. 136002-123. | |
| 136002-112 | L Programmable Read-Only Memory | (R3) Acceptable substitute is part no. 136002-124. | |
| 136002-125 | Programmable Read-Only Memory | (D7) | |
| 136002-133 sem | Programmable Read-Only Memory | (D1) | |
| 136002134 OS @ § | Programmable Read-Only Memory | (F1) | |
| 136002-135 | §8 g | Programmable Read-Only Memory | (J1) |
136002136 B = 3 | Programmable Read-Only Memory (L/M1) BSE
| 136002-137 -"8 | Programmable Read-Only Memory | (P1) |
| 136002-138 | L Programmable Read-Only Memory | (N/P3) |
| 137002-001 | Type-74S86 Integrated Circuit | (M8) |
| 137149-001 | Type-74LS11 Integrated Circuit | (F9) |
137158-002 Type AM6012PC 12-Bit Digital-to-Analog Converter (For -02 & -04 PCB assy. only: A10, F10) Acceptable substitute is part no. 137150-001. 137159-001 Type DAC-08CN 8-Bit Digital-to-Analog Converter (D10) 137160-003 Type MC3410 10-Bit Digital-to-Analog Converter (For -01 & -02 PCB assy. only: B10, E10) Acceptable substitute is part no. 137160-004.
| 144000-001 | 12.096 MHz, + .005%, Crystal | (¥1) Acceptable substitute is part no. 90-102. |
| 179014-012 | 12-Pin Polarized PCB Header | (J19) |
179051-001 Test Point
Tempest ™/Cabaret™
A037540.01 (Grd. Wire) 99-11009 037469-01 (Bracket)
179035-001 (Lampholder)
70-304 (Tube)
142028-xxx (lansformer) 79-561816P_ 99-1008 (Wire Nut) (Starter)
A005493-01 (Harness) NOTICE TO ALL PERSONS RECEIVING THIS DRAWING 99-11006 CONFIDENTIAL; Reproduction forbidden without the spe- (Tab) Gific written permission of Atari, Inc., Sunnyvale. CA. This drawing is only conditionally ssved, and neither receipt nor Bossession thereof conters or transters any right ms oF Ir Eense to use, the subject matter of the drawing or any de Sigh oF technical information shown thereon. nor any fight to reproduce this drawing or any part thereof, Except for manufacture by vendors of Atari, Inc, and for manufacture Under the corporation's written license, no right = granted to reproduce this drawing or the subject matter thereat, un: less by written agreement with or written permission from the corporation,
Figure 24 Fluorescent Light Assembly A037979-01 and -02 A
Parts List
Part No. Description
A005493-01 Light Harness Assembly A037540-01 Ground Wire with Ring Lug 70-304 18-Inch 15-Watt Cool White Fluorescent Tube 79-561816P Spring-Connector Wire Nut for 16- to 18-Guage Wires
99-11003 Fluorescent Lamp Starter 99-11006 Fluorescent Lamp Locking Tab (tab consists of two pieces) 99-11009 Starter Socket 037469-01 Steel Lamp Bracket
142028-001 60-Hz 118-Volt Ballast Transformer 142028-002 50-Hz 118-Volt Ballast Transformer 179035-001 2-Pin Fluorescent Lampholder
Tempest ™iCabaret™
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL” Reproduction forbidden without the Specific written permission of Atari, Inc., Sunnyvale, CA This drawing is only conditionally issued, and neither receipt nor possession thereof confers or transfers any right in, or license to use, the subject matter of the drawing ‘of any design 0” technical information shown thereon, nor any right t0 reproduce this drawing OF any part thereot. Ex cept for manulacture by vendors of Atari, Inc. and for manufacture under the corporation's writen license, no right te reproduce this drawing Is granted or the subject matler thereof unless by written agreement with or written permission from the corporation A037395-01 (Transformer Assy.)
A021084-xx (Volt, Plugs) 29-053 (Ci (Capacitor) / p3asae-c1 7 (Fuse Block Cyr.)
79-4411001 (Fuse Post) 78-70501SC (Cap. Bracket) ' 5 LL, 46-2017002 s 4 (Fuse)
A035881-01 (Fuse Harness) 034482-02 (Chassis)
46-301203 (Fuse) \
037639-01 (Label)
78-2708 (Bushing)
A034630-01 79-3206 (Filter Assy.) (Fuse Block) 037641-01 46-2014002 (Label) (Fuses)
A035890-01 79-15021001 (Term. Block) (Pwr. Harness)
A034629-01 3A-MDA3501 (AC. Harn.) (Rectilier)
Figure 25 Color X-Y Power Supply Assembly A037396-xx B
Tempest™/Cabaret™
Figure 25 Color X-Y Power Supply Assembly Parts List
Part No. Description (Reference Designations in Bold)
| A021084-01 | Voltage Plug for 100V | (violet) |
| A021084-02 | Voltage Plug for 120V_ | (yellow) |
| A021084-04 | Voltage Plug for 220V | (biue) |
| A021084-05 | Voltage Plug for 240V | (brown) |
A034629-01 A.C. Harness Assembly
| A034630-01 | RFI Filter Assembly | (FL1) |
A035890-01 Power Harness Assembly A035891-01 Fuse Harness Assembly
| A037395-01 | Transformer Assembly | (T1) |
29-053 27,000 uf 15 VDC Electrolytic Capacitor (C1) 3A-MDA3501 Bridge Rectifier, Type MDA 3501 (CR1)
| 46-2014002 | 4-Amp. 250V 3AG Slow-Blow Glass Cartridge-Type Fuse | (F2, F4-F6) |
| 46-2017002 | 7-Amp. 250V 3AG Slow-Blow Glass Cartridge-Type Fuse | (F1) |
| 46-301203 | 20-Amp. 32V 3AG Slow-Blow Glass Cartridge-Type Fuse | (F3) |
78-2708 Nylon Type 6/6 Hole Bushing with %-Inch Inside Diameter x °%,-Inch Outside Diameter x Ya-Inch Thick 78-70501SC 2-Inch Diameter Capacitor Mounting Bracket 79-15021001 2-Circuit Single-Row Terminal Block 79-3206 5-Position 3AG Fuse Block with ¥%-Inch Quick-Disconnect Terminals 79-4411001 Panel-Mounting Non-Indicating 3AG Cartridge-Type Fuse Post 034482-02 Power Supply Chassis. 034544-01 Fuse Block Cover
| 037639-01 | Label for Fuse Value | (F1) |
| 037641-01 | Label for Fuse Values | (F2-F6) |
‘Tempest ™/Cabaret™
99-15051 (Lamp Holder)
99-15056, (Screw for Bezel) ~ | 99-15040 (Lever) 99-15026 (Coin Inlet)
(Coin Iniet)
PART OF 99-15041
99-15054 a ae > dy 99-15041 (Pivot tor Lever) (Reing. Screw) (Lockout Coil) { 99-15053 (Lockt. Coil Spring) 9915027 / *: (Coin Ret. Box) ee . & ™ b 9915030 ~~ (ue (Lockout Flap)
a tl “he 99-15028
ae (Coin Ret. Box)
98-15056 (Screw for Bezel) 99-15037 (Sw. Adjuster)
99-15060 ? (Sw. Cover) 99-15029 (Bracket)
99-15042 (Switch) ae
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permissicn of Atari, Inc., Sunnyvale, CA. This drawing is only conditionally issued, and neither receipt nor possession thereot conters oF transfers any fight in, oF Heense 0 use, the subject matter of the draw. {ng oF any design or technical information sncwn thereon, nor any right to reproduce this drawing ot any pari thereot, Except for manulacture by vendors of Atari, In¢and lof manutacture under the corporation's written license, no right to reproduce this drawing is granted or the subject matter thereof uniess by witien agreement with of written permission from the corporation.
Figure 26 Vertical-Mounted Coin Door A037619-xx B
99-15067 (Lock Assy.)
99-15063 (Screw)
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, inc., Sunnyvale, CA. This drawing is only conditionally issuea, and neither receipt nor possession thereof confers or transfers any right in, or li cense to use, the subject matter of the drawing or any de- ‘sign or technical information shown thereon, nor any right to reproduce this drawing or any part thereof. Except for ‘manufacture by vendors of Atari, Inc., and for manufacture under the corporation's written license, no right is granted to reproduce this drawing or the subject maiter thereof, un: less by written agreement with or written permission from the corporation’ 99-15062 (Hinge) 99.15067 (Lock Assy.)
99-15036 (Cover) Tempest™/Cabaret™
99-15038 (Bezel for Button)
99-15001 thru 99-15012 (Ret. Button)
99-15052 (Spring for Button)
99-15065 (Clamp)
99-15039 (Bezel for Cover)
99-15066 (Screw)
‘The 171004-xxx coin doors below do not include the hamess assembly, which is part number A037542-01.
171004-001 — U.S. 25¢/25¢ Coin Door 171004-002 — U.S. 50¢/50¢ Coin Door 171004-003 — Canadian 25¢/25¢ Coin Door 171004-004 — British 10 P/10 P Coin Door 171004-005 — British 10 P/50 P Coin Door 171004-006 — British 20 P/50 P Coin Door 171004-007 — Australian 20¢/20¢ Coin Door 171004-008 — German 1 DM/1 DM Coin Door 171004009 — German 2 DM/1 DM Coin Door 171004-010 — German 2 DM/5 DM Coin Door 171004011 — an 1 DM/5 DM Coin Door 171004-012 — 5 Fri Fr Coin Door 171004.013 — Swiss 1 Fr/1 Fr Coin Door 171004.014 — French 1 Fr/1 Fr Coin Door 171004015 — French 2 Fri1 Fr Coin Door 171004016 — Swedish 1 Kr/1 Kr Coin Door 171004017 — Spanish 25 Pts/25 Pts Coin Door 171004018 — italian 100 L/100 L Coin Door 171004019 — Hong Kong $1/$1 Coin Door 171004-020 — Japanese 100Y/100Y Coin Door
Figure 26 Vertical-Mounted Coin Door A037619-xx B
Tempest ™/Cabaret™
Figure 26 Vertical-Mounted Coin Door, continued Parts List
Part No. Description
A037542-01 Harness Assembly
99-15001 Coin Return Button with U.S, 25¢ Price Plate 99-15002 Coin Return Bution with U.S. $1 Price Plate 99-15003 Coin Return Button with German 1 DM Price Plate 99-15004 Coin Return Button with German 2 DM Price Plate 99-15005 Coin Return Button with German 5 DM Price Plate 99-15006 Coin Return Button with Belgian 5 Fr Price Plate 99-15007 Coin Return Button with French 1 Fr Price Plate 99-15008 Coin Return Button with Japanese 100 Yen Price Plate 99-15009 Coin Return Button with British 10 Pence Price Plate 99-15010 Coin Return Button with Australian 20¢ Price Plate 99-15011 Coin Return Buiton with Italian 100 Lire Price Plate 99-15012 Coin Return Button with U.S. 50¢ (2 x 25¢) Price Plate 99-15025 Left Half of Coin Inlet 99-15026 Right Half of Coin Inlet 99-15027 Side Plate of Coin Return Box 99-15028 Base Plate of Coin Return Box 99-15029 Switch Bracket 99-15030 Fiap for Lockout Coil (U.S. 25%) 99-15036 Coin Return Cover 99-15037 Switch Adjuster 99-15038 Bezel for Coin Return Button 99-15039 Bezel for Coin Return Cover 99-15040 Coin Return Lever 99-15041 Lockout Coil 99-15042 Coin Switch for U.S. 25¢ 99-15051 Lamp Holder 99-15052 Spring for Coin Return Button 99-15053. Spring for Lockout Coi! 99-15054 Pivot for Coin Return Lever 99-15055 Retaining Screw 99-15056 Screw for Both Bezels 99-15060 Switch Cover 99-15062 Hinge 99-15063 Screw for Hinge 99-15065. Clamp for Frame 99-15066 Screw for Clamp Lock Assembly 99-15067
a YOUR COMMENTS, PLEASE! poe aed
Your comments will assist Atari in improving the usefulness of our publications. They are an important part of preparing for revisions of manuals and parts catalogs. No postage stamp is necessary if mailed in the U.S.A.
If you have any technical questions about certain Atari or Kee Games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.
Page: Comments:
Fill in if you wish a reply:
Name.
Firm © Distributor
Address CO Operator
City State Zip U Other__
Area Code Phone
First fold
BUSINESS REPLY MAIL
FIRST CLASS PERMIT NO. 1004 SUNNYVALE, CA
POSTAGE WILL BE PAID BY ADDRESSEE
Atari, Inc. Attn.: Field Service/Coin-Op Division P. O. Box 427 Sunnyvale, California 94086 No Postage Necessary +f mailed in the United States
] } PE PGR RG GE LO LG Pp > » ° p >
Warranty
Seller warrants that its printed-circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its video displays (in games supplied with displays) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment. None of the Seller's other products or parts thereof are warranted.
If the products described in this manual fail to conform to this warranty, Sellers’ sole liability shall be, at its option, to repair, replace, or credit Buyer’s account for such products which are returned to Seller during said warranty period, provided:
- Seller is promptly notified in writing upon discovery by Buyer that said products are defective,
- Such products are returned prepaid to Sellers’ plant; and
- Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation or improper testing.
In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages. 5
Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms of this order, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller's part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products under this order.
Piles Sates Sate Salad Nate Mateo Nad Satie) Mat The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to yourself and others. Be very cautious in using non-Atari-supplied components with our games, in order to insure your safety.
Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories. Atari cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor.
This document is and contains confidential trade secret information of Atari, Inc.
This document is loaned under confidential custody for the sole purpose of operation, maintenance or repair of Atari equipment and may not be used by or disclosed to any person for any other purpose whatever, and remains the property of Atari, Inc.
Neither it nor the information it contains may be reproduced, used, or disclosed to persons not having a need to know consistent with the purpose of the loan, without written consent of Atari, Inc.
ATARI INC 1265 BORREGAS AVENUE P.O. BOX 427 SUNNYVALE, CALIFORNIA 94086 ATARI 408/745-2000 ¢ TELEX 35-7488