CATHODE RAY TOMES

Naughty Boy

Naughty Boy (Jaleco, 1982) · Manual · 86 pages · 61 sections · original scan

Page 1

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 2

co co

| a OPERATION AND MAINTENANCE

MANUAL

CINEMATRONICS, INC.. 1841 FRIENDSHIP DRIVE EL CAJON, CA 92020 (714) 562-7000

TELEX: CINEMAT ELCJ 697891

CALL TOLL FREE: (800) 854-2666 IN CALIFORNIA CALL: (714) 562-7000

SALES: 8-5 (PST) WEEKDAYS SERVICE: 8-5 (PST) WEEKDAYS

Page 3

| a

c

| ae

Cy

oS

C

~ im NAUGHTY BOY

GAME MANUAL

TABLE OF CONTENTS

PAGE FCC WARNING . . «© 6 6 6 ee we ee ee we ee we we ee 1

WARRANTY. . «6 6 2 6 ee ee ee ee ee ee ee eee 2

CUSTOMER SERVICE PROCEDURES . . . . «2 e+ «© © © ee we we we 3

RECEIVING AND INSTALLING. . 2. 2. 2 2 ee ee ee ee ee we 5

NAUGHTY BOY - GAME DESCRIPTION. . . . 2. 2 2 © © 2 ee we ee 6

OPTION SWITCH SETTINGS. . . «2 2 © © ee we ee ew we ew ew ew 10

ROUTINE MAINTENANCE . 2. 2. 2. 6 6 2 0 ee ee ew we ee we we we 11

WELLS-GARDNER COLOR MONITOR INFORMATION. ......... 12

PARTS LIST - GAME ASSEMBLY. . . . «© © «© 2 © © © © © © eee 28

PARTS LIST - ELECTRONIC BOARDS. . . «~~ 2 «© «© © + © © we oe 39

BOARD EDGE CONNECTOR PIN-OUT LIST . . . 2. «© «© © © es we we ee 43

APPENDIX A -

ASSEMBLY DRAWINGS AND SCHEMATICS:

ELECTRONIC BOARD LAYOUTS AND SCHEMATICS

GAME ASSEMBLY DRAWINGS, SCHEMATICS AND HARNESS WIRE LISTS

Page 4

kK

C2 te tt

; on

Cc CINEMATRONICS, INC.

WARNING:

This equipment generates, uses, and can radiate radio frequency energy; and, if not installed and used in accordance with the Instruction's Manual, may cause interference to radio communication. As temporarily permitted by regulation, it has not been tested for compliance pursuant to Subpart J of Part 15 of FCC rules, which is designed to provide reasonable protection against such interference. Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures may be required to correct the interference.

Page 5

WARRANTY

Cinematronics, Inc. warrants the goods to be free from defects in material and workmanship under normal use and service for a period of ninety (90) days from the date of shipment from factory. Cinematronics makes no representation or warranties concerning the goods whether express or implied by operation of law or otherwise, including those of merchantability or fitness for any particular purpose, or with respect of patent infringement, except as may be specifically made herein. Cinematronics limits its warranty obligations herein to the repair or replacement of such parts which have been returned to Cinematronics' plant at purchaser's expense and which examination shall disclose Cinematronics' satisfaction to have been so defective and to the shipment of such repaired or replacement parts to the purchaser F.O.B. the shipping point.

This warranty does not apply to any Cinematronics' product which has been altered or repaired by unauthorized personnel or service facilities or any products which have had the unit serial number altered or removed.

Upon acceptance of the goods, the purchaser agrees to assume all liability for damages and/or bodily injury by the purchaser or any other person and to hold Cinematronics, Inc. harmless from liability or claims arising from the use of the goods by any person. Purchaser further agrees to indemnify Cinematronics, Inc. from any liability, claim, cause of action or litigation resulting from the use or misuse of the goods by any person.

Parts.returned for warranty service must be packaged so that no damage is incurred during the shipment. Full documentation and instructions must accompany returned parts. Parts must be shipped prepaid to: Cinematronics, Inc. 1841 Friendship Drive El Cajon, CA 92020 795 DT 2

a

=

q

Page 6

C

a

Cc

ron

C=

Cc

py i i

moot re co

tC CUSTOMER SERVICE PROCEDURES FOR AUTHORIZED CINEMATRONICS' DISTRIBUTORS

It is the desire of Cinematronics, Inc. to provide efficient and courteous service should the need arise. We have a fully staffed Customer Service Department and encourage you to call our toll-free number: (800) 854-2666 for technical assistance between the hours of 8:00 A.M. and 5:00 P.M., California time, Monday through Friday.

In order to provide the very best service possible, the following procedure for ordering or returning parts must be followed:

  • All equipment ordered from Customer Service, whether in or out of Warranty, must be placed with a Distributor's purchase order, either by mail or verbally by telephone.
  • Advance replacement items may be obtained only during the term of the Warranty and when such items are available, using the same procedure as when ordering parts. When ordering a PCB, please include with your order the game serial number and the number of the PCB you wish replaced.
  • All items received as advance replacements will, after a period of thirty (30) days, become the property of the Distributor, with applicable charges applied in the event Customer Service has not received the defective item against which the advance replacement was made.
  • The Distributor must call this facility for an RMA number prior to returning any item. Please be prepared to provide us with the game serial number and the PCB number when requesting an RMA.
  • In all situations covered above, and in all other situations, the Warranty offered by Cinematronics, Inc. is applicable and should be fully understood.
  • Parts returned for service must be packaged so that no damage is incurred during she shipment. Cartons without a prominently displayed RMA number will not be accepted. Full
Page 7

documentation including game serial number, PCB number on outside of package, and reason for return must accompany parts. Ship prepared to: Cinematronics, Inc. Customer Service Department 1841 Priendship Drive El Cajon, CA 92020

(800) 854-2666 (714) 562-7000 as |

a

~

a)

i.

a]

Page 8

{

i oe

C

t([ me

~~ (= {

c

Cc

Cc

| oe

{i uo

Cc RECEIVING AND INSTALLING

RECEIVING INSPECTION

Your game was shipped in ready-to-play condition. However, after removal of the shipping carton, a brief visual examination is suggested.

Naturally, you will want to make note of any physical damage to the game cabinet and its external components for freight claim purposes. Considering the quality of the shipping carton, any

damage to the exterior would indicate possible interior damage

as well.

The interior of the game should also undergo a brief examination for: loose mounting hardware (check to be sure that the major components are still securely mounted); disconnected or loose wires, cables or harnesses; electronic devices loose in their sockets; etc.

At this time the game serial number should be logged. Remember that the game serial number will be required if you need service from your distributor. Please complete the postage-free reply card and mail immediately.

ELECTRICAL REQUIREMENTS

Unless specified otherwise, your game was shipped to operate at 115 VAC, 50/60 Hz. .

A good earth ground is essential for the proper operation of this game or for that matter, any electronic device. Problems with instability and erratic operation of computer-type devices can usually be traced to an ineffective ground system. Therefore, plug the game into a properly wired three prong outlet. If a three prong to a two prong AC adaptor must be used, an alternate method of grounding the third prong must be used.

Page 9

NAUGHTY BOY

GAME DESCRIPTION

GAME PLAY

Game play for Naughty Boy proceeds through four different screens. These screens will appear in sequence. Each time a player successfully maneuvers through all four screens, the screens repeat their appearance, with more objects moving at higher speeds. In addition, after successfully completing even numbered rounds, the player is awarded a bonus round.

SCREEN ONE

This screen begins with Naughty Boy standing in a forest. In front of him are several monsters. There is also a safety zone that can be entered through two red doors, which the monsters cannot enter. The same type of doors appear on fences along the side of the screen. Naughty Boy can appear on the other side of the screen by passing through one of these doors.

As Naughty Boy moves towards the top of the screen, the images scroll downwards. Above the forest is a series of fences, then a group of ponds, and finally, walls of a fortress. Some goblins guard the top portion of the screen.

Naughty Boy must maneuver his way through the forest, past the fences and ponds and destroy the flags that are flying on the fortress. The player controls Naughty Boy with a four position joystick. In addition, a throw button allows the player to throw rocks at objects to destroy them.

Naughty Boy must avoid contact with the monsters and goblins or he will be destroyed. Also, a dragon will randomly appear on the ponds breathing fire. If Naughty Boy is hit by the fire, he will be destroyed.

The safety zone allows Naughty Boy to attack the monsters and goblins without danger by throwing rocks at them outside. A timer begins to decrease whenever Naughty Boy is inside the a ee

i

pe)

a]

=

J ee en ee Bee

aa

Page 10

C=

t.

(-

a

| ae

Cc

{

Cc safety zone. Once the timer reaches zero, the red doors disappear and Naughty Boy can be attacked.

Periodically, a question mark will appear on the screen. If Naughty Boy hits the question mark with a rock, he will become invincible to attack from the monsters and goblins for a short time. Naughty Boy can still be destroyed by the dragon. After the question mark is hit, different objects will appear in the same spot. These objects will score bonus points when hit with rocks.

Once Naughty Boy reaches the fortress, he must hit all the flags with rocks. Two flags can be destroyed with one throw, if the rock lands in between two flags. Once all the flags are destroyed, Naughty Boy will proceed to the next screen.

If Naughty Boy is destroyed before he is able to destroy all the flags, he will reappear at the starting position of the screen he is currently in. Any flags destroyed by Naughty Boy remain destroyed.

Naughty Boy always throws in the direction that he is facing. The distance a rock is thrown is determined by how long the throw button is depressed.

SCREEN TWO

This screen is an open field. A safety zone is in the center of the field. Monsters and goblins are scattered around the field. Robots guard the fortress at the top of the screen.

Play proceeds as in the first screen. The dragon appears randomly in the field above the safety zone. Once all the flags are destroyed, Naughty Boy will appear in the next screen. :

SCREEN THREE

Naughty Boy begins his adventure in the center of a maze. Goblins and monsters will chase Naughty Boy through the maze. At the top of the maze is the safety zone. Above the safety zone is the fortress. No dragons appear in this screen.

Page 11

SCREEN FOUR

In this screen Naughty Boy is standing between the safety zone and some ponds. The dragon will randomly appear in the ponds. Above the ponds is a series of fences and walls. Once Naughty Boy passes through these, he reaches the fortress.

If all the flags are destroyed in this screen, Naughty Boy will appear in Screen One. However, Naughty Boy must fight more objects which are moving faster. This is true for every screen that Naughty Boy goes through.

BONUS PLAY

After successfully completing even numbered rounds, the player is given a bonus play. During bonus play, Naughty Boy flies back and forth at the top of the screen in a balloon. A fuel gauge above the balloon indicates how much bonus play is left. At the bottom of the screen, a female monster runs back and forth.

Naughty Boy throws objects out of the balloon and tries to hit the monster on the head. If the monster is struck, she changes expressions momentarily. The fuel gauge decreases as play proceeds. Play continues until the fuel runs out.

Play continues until all of a player's Naughty Boys are destroyed. A player can earn one extra Naughty Boy based upon his score achieved and the operator adjustable level, selected.

SCORING

Monsters, Goblins & Robots - 250 Points to 9000 Points

Flags - 200 Points to 2000 Points

Bonus Objects - 500 Points to 9000 Points

FEATURES

  • Number of Naughty Boys per game operator adjustable is 2, 3, 4 or 5.
  • Point level at which the extra Naughty Boy is awarded is operator adjustable at 10,000, 30,000, 50,000 or 70,000 points. TI

Ss es Ss RN DE DS |

a

Page 12

C= C= Co

:

tf Cc

C CZ fe

c

t= ¢

(—

C2

C= 3.

5.

6.

7. Four coinage options.

Easy/hard switch for longer game life.

Four different screens and bonus play round. Fifty difficulty levels.

Throw distance controlled by the throw button.

Page 13

NAUGHTY BOY

OPTION SWITCH SETTINGS

NUMBER OF NAUGHTY BOYS

EXTRA BOY

CREDITS

| x | rcoin rey | | | | for{on] || | | coins a vuay | | | | foxfore| || a ce ee ee

GAME TYPE

Page 14

Cc

i oa

LY aad

C ROUTINE MAINTENANCE & SERVICE

Because of the solid state electronic circuitry, this machine should require very little maintenance and only occasional adjustments. However, it is necessary to take measures to ensure this.

The volume control is located on the rear of the coin door and can be accessed by opening the coin door.

The video monitor has been properly adjusted before shipping. Occasionally minor adjustments are necessary. See monitor specifications and schematics for technical information. Adjustment controls for the monitor are located at the rear of the monitor.

This machine should be serviced only by a qualified technician.

Do not make any adjustments on this machine while the power is on.

For service information, contact:

CINEMATRONICS, INC. 1841 FRIENDSHIP DRIVE

EL CAJON, CA 92020 (714) 562-7000

POWER SUPPLY

The computer board in this game operates most efficiently and reliably when the power, supply is set so that the voltage on the board is 5.0 volts, -0.1 volts. To check this, place a meter across 5 volts and ground at the edge connector. If necessary, adjust the screwdriver control on the power supply so the meter reads between 4.9 and 5.1 volts.

ll

Page 15

TI a wells-qardner electronics n _ = CORPORATION 7 f]

19” IN LINE COLOR MONITORS n

MODELS 19K4625 L 19K4626

im] i

H MODELS nt Gexsezs) r 19K4676 | 19K4677 5 it n

CORPORATION 7

\2 n

Page 16

c

to

tr

OT. C

cl

a on

C

Cc CO Cf

Cc WARNINGS

  • Power Up Warning— An isolation transformer must be used between the AC supply and the AC plug of the monitor before servicing or testing Is performed since the chassis and the heat sink are directly connected to one side of the AC line which could present a shock hazzard. Before servicing is performed, read all the precautions tabelled on the CRT and chassis.
  • | X-RAY RADIATION WARNING NOTICE
WARNING: PARTS WHICH INFLUENCE X-RAY RADIATION IN HORIZONTAL DEFLECTION, HIGH VOLTAGE CIRCUITS AND PICTURE TUBE ETC. ARE INDICATED BY (#) IN THE PARTS LIST FOR REPLACEMENT PURPOSES. USE ONLY THE TYPE SHOWN IN THE PARTS LIST.
  • High Voltage— This monitor contains HIGH VOLTAGES derived from power suppiles capable of delivering LETHAL quantities of energy. Do not attempt to service until all precautions necessary for working on HIGH VOLTAGE equipment have been observed.
  • CRT Handling— Care must be taken not to bump or scratch the picture tube as this may cause the picture tube to implode resulting in personal injury. Shatter proof goggles must be worn when handling the CRT. High voltage must be completely discharged before handling. Do not handle the CRT by the neck. 8, | PRODUCT SAFETY NOTICE
WARNING: FOR CONTINUED SAFETY REPLACE SAFETY CRITICAL COMPONENTS ONLY WITH MANUFACTURER RECOMMENDED PARTS. THESE PARTS ARE IDENTIFIED BY SHADING AND BY (4) ON THE SCHEMATIC DIAGRAM. AVERTISSEMENT: POUR MAINTENIR LE DEGRE DE SECURITE DE L'APPAREIL NE REMPLACER LES COMPOSANTS DON Oe Fenen TONNEMENT EST CRITIQUE POUR LA SECURITE QUE PAR DES PIECES RECOMMANDEES PAR LE FABRICANT. For replacement purposes, use the same type or specified type of wire and cable, assuring the positoning of the wires is followed (especially for H.V. and power supply circuits). Use of alternative wiring or positioning could result in damage to the monitor or In a shock or fire hazard.

PERFORMANCE AND OPERATING DATA 1, Apply a sultable power source to the monitor through an isolation transformer.

  • Apply a sultable signal source to the monitor PCB by means of P205.
  • Set Up Controls. All controls are preset at the factory, but may be adjusted to sult program material. 1.0 Supply

Voltage 108 VAC-132 VAC

Frequency 50 Hz-60 Hz

Note: Apply supply voltage through an Isolation transformer with 1 Amp. minimum capability. 2.0 High Voltage (EHT) For 19"V models 25.5+0.8 K.V. at 0 Beam
Note: Condition for above 1 (beam) = 0 AC. = 120V

3.0 Service Set-Up Controls INTERFACE PC BOARD 3.8 Black Level Control, VR201 3.9 Horizontal Video Position Control, VR202 POWER PC BOARD 3.1 Voltage Adjustment, VA501 (Set for 127V DC)

t VERTIHORIZ PC BOARD NECK PC BOARD 3.2 Vertical Hold Control, VR301 3.10 Video Drive Controls, a Ae 2 3.3. Vertical Size Control, VR302 reen 3.4 Horizontal Oscillator Coll, L351 3.41 CRT Cut Off Controls, Red VR403

3.5 Horizontal Hold Control, VR351 Breen wanes

MAIN PC BOARD 3.12 Screen Control, VR408 3.6 Vertical Raster Position Adjustment, J604 CHASSIS

3.7 3 positions) Horizontal Raster Position Adjustment, J608 (3 positions) 3.13 Focus Control, VR702 3.14 Horizontal Width Coil, L702

Page 17

SERVICE INSTRUCTIONS

NOTE: All monitors are equipped with automatic degaussing colls (L701) which demagnetize the picture tube every time the monitor is turned on after being off for a minimum of 5 minutes. Should any part of the chassis become magnetized it will be necessary to degauss the affected area with a manual degaussing coil. Move the coil slowly around the CRT face area then slowly withdraw for a distance of 6 feet before turning off.

1.0 +127V ADJUSTMENT (See Fig. 1) The + 127V adj. control (VR501) Is adjusted at the factory. However, if readjustment should be required, proceed as follows. 1.1. Operate monitor for at least 15 minutes at 120V AC line. 1.2 Connect Positive lead of V.T.V.M. to blue lead of TR502 negative lead to chassis ground. 1.3 Adjust VA501 to obtain + 127V reading. 1.4 After adjustment VR501 must be locked with a sealing varnish. 2.0 BLACK LEVEL CONTROL ADJUSTMENT This contro! has been set at the factory and should not need further attention, however, when the game is connected a slight adjustment of VR201 may be necessary to obtain the proper black level (the black portion of the picture just extinguished), 3.0 VERTICAL SIZE (HEIGHT) The vertical height contro! is a screw-driver adjustment. Location of this control is shown in Fig. 2. This contro! must be adjusted slowly, if necessary, until the picture or test pattern attains the correct vertical proportions. 4.0 CIRCUIT PROTECTION A3.0A pigtail fuse, mounted on the Main Board has been provided to protect the Power Output Circuit. 5.0 FOCUS Adjust the Focus control (VR702), located on the HV unit(T701), for maximum over-all definition and fine picture detail. 6.0 HORIZONTAL OSC. ALIGNMENT (See Fig. 2) A warm-up period of at least five minutes should be allowed before alignment is carried out. With the monitor being driven from the game signal, set VR351 to its mechanical center and short the lower end of R328 (TP32) to ground. Adjust L351 until picture stops sliding horlzontally. Remove the short. 7.0 HORIZONTAL VIDEO POSITION If the video is off center on the raster some compensation can be made by adjusting this control. 8.0 VERTICAL RASTER POSITION ADJUSTMENT \f the video is off center vertically, (short dimension of picture tube) some compensation can be made by moving J604 to either No.1 or No. 3 of P604. Position No. 1 moves raster up and position No.3 moves raster down. 9.0 HORIZONTAL RASTER POSITION ADJUSTMENT If the video Is off center horizontally (long dimension of picture tube) some compensation can be made by moving J608 to elther No. 1 or No.3 of P608. Position No. 1 moves raster to the left and position No. 3 moves raster to the right.

VABO! +B Ad)

‘Seal cr Lock

FIGURE 2 VERT./HORIZ. BOARD

Page 18

CH fe tf fc oo Ce ee oe oe oe

c= INSTALLATION AND SERVICE INSTRUCTIONS

OUTLINE OF CONVERGENCE AND SET-UP PROCEDURE 1.0 Degaussing-Demagnetize shadow mask with external degaussing coil. 2.0 Purity and Vertical Centering—Adjust purity magnet and yoke position, 3.0 Static Convergence-Converge Red and Blue on Green in center of screen. 4.0 Dynamic Convergence-Converge Red and Blue at edges of screen. 5.0 White Balance-Set Gray and White brightness tracking.

NOTE: Number 2.0 and 3.0 adjustments Interact.

1.0 DEGAUSSING The monitor Is equipped with an automatic degaussing circuit. However, if the CRT shadow mask has become excessively magnetized, it may be necessary to degauss It with manual coll. Do not switch the coil OFF while the raster shows any effect from the coll.

2.0 COLOR PURITY AND VERTICAL CENTERING ADJUSTMENT 2.1 For best results, it Is recommended that the purity adjJustment be made in the final monitor focation. If the monitor will be moved, perform this adjustment with It facing west or east. The monitor must have been operating 16 minutes prior to this procedure and the faceplate of the CRT must be at room temperature. 2.2 Set the converger assembly on the CRT neck with the center line (of the Purity Adjustment Magnet) over the gap between grids no. 3 & 4. (See Figure 3). 2.3 Make certain that the magnetic ring-pairs are in their correct positions before starting procedure. This produces a zero-correction state and helps facilitate adjustments. 2.4 Models which have vertical raster position adjustment, J604 must be In position #2 (center) of P604. 2.5 Remove R-G-B signal from monitor. 2.6 Turn Green Cut off Control (VR404) on the Neck Board fully CCW. (See Fig. 4) 2.7. Turn Red and Blue Cut off Control (VR405) fully CW. 2.8 Pull the Deflection Yoke backward so that the Magenta belt will appear. (See Fig. 5) 2.9 Move the two Purity Magnets and bring the Magenta belt to the mechanical center of the screen. 2.10 Push the Deflection Yoke forward gradually and fix it at the place where the Magenta screen becomes uniform throughout. 2.11 Turn Cut off Control, and Drive Control and confirm that each color is uniform. 2.12 If the color Is not uniform, re-adjust it moving Purity Magnets slightly. 2.13 Move a pair of Purity Magnets at the same time (do not change the angle of the pair), and adjust the vert. center to center of screen. 2.14 Obtain the three colors and confirm whether white uniformity ts balanced. 2.15 Insert the temporary wedge as shown In Fig. 5 and adjust the angle of Deflection Yoke. RED/BLUE REO/BLWE ON GREEN ‘CLOCK 10 O'CLOCK ae

Roan CONCENTRIC [ CONVERGER Assy. SHOWN IN ZERO CORRECTION POSITION, Purity purity socio —”_— so'ciock INOIVIDUAL ‘TAB ROTATION

FIGURES

FIGURE 4

NECK BOARD

‘TEMPORARY WEDGE | | | ox ||P) ‘MAGENTA BELT

FIGURES

Page 19

3.0 STATIC CONVERGENCE ADJUSTMENT GREEN GUN 15 THE CENTER GUN. ua CONVERGE a7 REO ANO BLUE. A recently developed Deflection Yoke and Electron Guns FHitn cOnvEnse’ReD ano BLUE ON GREEN.

construction has been used on this equipment in combination with In-Line Guns and Black Stripe Screen to | cQwencctce |mmeners make a barrel-type magnetic field distribution for vertical aUE Pps deflection and a pin-cushlon-type magnetic field for horizontal deflection with which a_ self-converging 3.2 system can be obtained. This type Is different from conventional unity-magnetic field distribution type deflectlon yoke. 4-Pole Magnets and 6-Pole Magnets are employed for static convergence instead of a Con- HORIZONTAL vergence Yoke. CONVERGENCE 3.1 Across hatch signal should be connected to BLUE & RED the monitor. 3.2 Apair of 4-Pole Convergence Magnets are provided and adjusted to converge the blue and red beams. When the Pole opens to the left and right 45° symmetrically, the magnetic fleld maximizes. Red and blue beams move to 3.3

VERTICAL the left and right oppositely (See Fig. 6) Varia- CONVERGENCE tion of the angle between the tabs adjusts the BLUE & RED convergence of red and blue vertical lines. ON GREEN 3.3 When both 4-Pole Convergence Magnet Tabs 34 are rotated as a pair, the convergence of the ted and blue horizontal lines Is adjusted. 3.4 A pair of 6-Pole Convergence Magnets are SLIDE also provided and adjusted to converge the HORIZONTAL magenta (red + blue) to green beams. CONVERGENCE When the Pole opens to the left and right 30° byt symmetrically, the magnetic field is maximized. Red and blue beams both move to the left and right (See Fig. 8). Varlation of the opening angle adjusts the convergence of magenta to green vertical lines. REPEAT 3.2 4 3.3 IF ALL LINES ARE NOT CONVERGED AT CENTER 3.5 When both 6-Pole Convergence Magnet Tabs 5827 are rotated as a pair the convergence of a magenta to green horizontal lines Is adjusted. FIGURE 6

ANODE CONTACT ot

i '

nd

bent 6 POLE CONVERGENCE MAGNETS _: 4 POLE CONVERGENCE MAGNETS Magner aSSe ~ PURITY CENTERING MAGNETS y

. = . ~———— DEFLECTION YOKE = =. nussen weoces FIGURE 7

n J

Page 20

a CD 2

t—

to.

CC

| oa

i

en ce

if

C

i | i 4.0 PRECISE ADJUSTMENT OF DYNAMIC CONVERGENCE (See Fig. 9 and 10)

Feed a cross hatch signal to the monitor. insert the temporary wedge and fix Deflection Yoke so as to obtain the best circumference convergence (See Fig. 9 and 10)

NOTE: The temporary wedges may need to be moved during adjustments. Insert three rubber wedges to the position as shown in Fig. 8 to obtain the best circumference convergence.
NOTE: Tilting the angle of the yoke up and down ad- Justs the crossover of both vertical and horizontal red and blue lines. See Fig. 9 (a) and (b). Tilting the angle of the yoke sideways adjusts the parallel convergence of both horizontal and vertical lines at the edges of the screen. See Fig. 10 (a) and (b). Use three rubber wedges (thick and thin rubber wedges are used for a purpose). ~ The angle of each rubber wedge is shown In Fig. 8. After three rubber wedges have been Inserted, pull out the temporary wedge. Fix the rubber wedges with chloroprene rubber adhesive.

DOR UPPER

a 8 @ @ cRrT 8 R

RGB UNDER

crt screen °) weert RUBBER WEDGE CRT SCREEN FIGURE 8

UPPER

crt vas

BGR LL,

INSERT RUBBER WEDGE FROM UPPER SIDE FROM LOWER SIDE

FIGURES

fe PY

CRT SCREEN (0) insert RUBBER WEDGE CRT SCREEN INSERT RUBBER WEDGE FROM LEFT SIDE FROM LOWER SIDE

FIGURE 10

Page 21

5.0 WHITE BALANCE

5.1

5.2 5.3

5.4

5.5

5.6 Refer to Fig. 11. and do the following In subdued light. Ground the R/G/B inputs. Set the R/B drive controls to thelr mechanical center. Set the screen and RI/G/B cutoff controls to minimum (fully CCW). Insert service tip “N” on Neck PCB to “S" on Vert/Horiz. PCB (see Fig. 11). Slowly turn the screen control (CW) until the first faint line appears. Do not touch the

eaanted cutoff control—it will stay fully

CW.

VERT/HORIZ. BOARD

6.0 HIGH VOLTAGE PROTECT

6.1

6.2 6.3 FIGURE 11 5.7 Slowly turn up the two remaining cutoff controls to match the first. This should result ina white line. Replace the Service Tip “N” to the Neck PCB. Adjust the Black Level Controt for dim raster. Touch up the cutoff controls for best gray uniformity. Adjust the Black Level Control for a bright White Raster. Adjust the R/B Drive Controls if necessary for best neutral white. Repeat steps 5.9 and 5.10 until good tracking of white balance Is achieved.

NECK BOARD

The AUTO PROTECT circuit prevents the high voltage from reaching dangerous levels should a defect such as a short circuit occur between collector and emitter of the voltage regulator transistor. When the + 127V DC exceeds approx. + 141V DC the horizontal oscillator Is shut down. When the defect Is removed the oscillator will not restart untll the power Is removed momentarily. im 9

Fs |

ad

—J

J

Page 22

tC FIGURE 12. MAIN P.C. BOARD al i om | an i on P.C. BOARD LAYOUT

Page 23

P.C. BOARD LAYOUT

ca) —_) a ee |

Page 24

Cc

C

CT ff

Co

Co fo ef

Cc

C

Cc

aa

ct P.C. BOARD LAYOUT

FIGURE 15. HORIZ/VERT PC. BOARD

a t sfelsle = . 2 2 : P203 P208 =-,, € G [7

‘x2 cat Ve

FIGURE 16, INTERFACE BOARD (P317 AND P318)

Page 25

ant REPLACEMENT PARTS LIST This monitor contains circuits and components Included specifically nm for safety purposes. For continued protection no changes should be made to the original design, and components shown in shaded areas of schematic, or 4 * _ on parts list should be replaced with exact factory replacement parts. The use of substitute parts may create a shock, fire, radiation or other hazard. Service should be performed by qualifled personnel only. a MAIN BOARD

Ret. No.Part No.Description‘Rel. No.Part No.Description_

RESISTORS CAPACITORS ,

R603330k Ohm, * 10%, 1/2W Carboncst203x1800-4510.1 uF, 125V, 20% MM
R606204x1425-021470 Ohm, + 10%, SW WW.C8022200 pF, Z5F, + 10% Ceramic
4% R607204x1450-5082.7k Ohm, = 10%, SWAc603202X7810-2142200 pF, 125V Coramionm
R608203X9014-6031.2k Ohm, £ 5%, 1W M.C60480X0096-0382200 pF.25F, + 10% Ceramic1]
R810203x6500-24622 Ohm,5%, 1/8W CarbonC805203x0220-043330 uF, 200V Electrolytic
Rett203x6700-5621k Ohm,5%, V2W CarbonC808203x0040.05247 uF, 160V Electrolytic
Re12340X3471-844470 Ohm, + 10%, 1/2W CarbonC809202X7050-3680033 uF, S00V, + 10% Ceramic
R613203X0010-7571.2k Ohm, # 5%, 1W MO.C810202X7050-483,01 uF, S00V, + 10% Ceramic
R614680k Ohm,5%, ZW Comp.C611202x8140.022100 pF, KV, + 10% Ceramic
RBIS203X5602-156270k Ohm,5%. 1/2W Comp.C12203X1201-047022 uF, 200V, + 10% PP
R816203x6500-7412.7k Ohm, = 5%, 1/8W Carbonca13,203X0015.035,220 uF, 25V Electrolytic
R617203X6501.08868k Ohm, 5%, 1/8W Carbonca14203x0015.00833 uF, 25V Electrolytic
R624203x6205-8431k Ohm, £5%, 12W CarbonCais,203X1201-2880.39 uF, 200V, + 10% PPion
F631203X0015-0872.2 Ohm, * 10%, SW M.O.ca1647 pF, S00V Ceramic
Reg2340X8121-731120 Ohm, #5%, SW Carbon617203x0025.0191 uF, 50V Electrolytici
R342.2 Ohm, = 5%, 1/8W CarbonC819209x0025.0191 uP, SOV Electrolytic
R635340Xx3602.0446.8 Ohm, = 6%, 1/2W Carbonca20209X1107.0380.1 UF, 100V, + 10% Mylar
eat203X6501-00233k Ohm,5%, 1/8W CarbonC6210.1 uF, 1.SKV, + 20% Papara
faa15k Ohm, +5%. 8W Carbon* C8221000 uF, 38V Electrolytic
R647340X5150-84115 Ohm, # 10%, 2W Carbon423203x0015-053470 uF, 25V Electrolytic!
R649340X3182-9441.8k Ohm, # 10%, 1/2W CarbonC628203x0015-021100 uf, 25V Electrolytic-
R650340x3271.-944270 Ohm, 10%, 1/2W Carbon82510 uF, 160V Electrolytic
Rest340X5241-743240 Ohm, + 10%, 2W CarbonC828202X7050-009100 pF, S00V, ‘s 10% Ceramic
Res26.8k Ohm, * 10%, 1/2W Carbonce27202X8065-48139 pF, S00V, + 10% Ceramic
onauaxtoo0s272200 oF. S00V, # 10% Coramic
C629203X1270-41. 1.5KV,-
SEMICONDUCTORS833203X0315-0332.2 uF, 50V Electrolytic
TROT200X3189-304Transistor, 2561893.C637202X8105-014IDF. 2kV, 20.5 pF Ceramicrm
x601201X3130-109Rectifier, (St) RM-2AV 600Vca38.056 uF, 10% Mylar
xenzo1x3t90 109Recs (S) AMCZAV goov

x 1X3130-1 ities, (SI) RM-2AV 600V

604201X3130-109Rectifier, (SI) RM-2AV 600VMISCELLANEOUS
X605200X8130-171Olode (HS) SB-2CGL 1200V min.F601204x7120-082Fuse (ULICSA) 38-125
608201X2010-144Diode (SI) 182473-772J607206X5003-860Socket, 6 Pin
x60?201X2100-119Diode (HS) RC-2V 0.8 USPeo2+204X9600-280Plug, 3 Pin (GT)
608201X2130-234Olode (HS) RU-2VPesos204x9600-298,PI
x09201X2130.234Diode (HS) RU-2VP8607204x9600-380Plug, 6 Pin (GT)
X610€8x0023-000Rectifler, Power (SI) SOOV PIV608204x9600-254Plug. 3 Pin (NM)
x611@8x0023-000Rectifier, Power (SI) SO0V PIVPent204x9600-670Plug, 2 Pin (NM)i
X612€6X0023-009Rectifier, Power (S1) 500V PIVTHEO!201X011.034Thermistor|

Bi lug, 6 Pin TRANSFORMERS & COILS *

Alsot201X6000-112Goll, Line Filter RS
602201X4600-042Coil, Filter, 10 uH
Te0z201X1300-080Transformer, Hor, Drive
1603202Xx1210-191Transformer, Side PC
7029A2795-003Width Coit

a VERT/HOR BOARD ion RESISTORS RESISTORS (CONT)

R301820 Ohm, #5%, 1/8W Carbon316203x6500-420120 Ohm, 28%, WW Carbon
R302203x6500-90212k Ohm, 5%, 1/8W CarbonA317203x6206-4412.2 Ohm, 25%, 1/2W Carbon
A303203X6500-92715k Ohm, 5%, 1/8W CarbonA318203x6501-00233k Ohm, = 5%, V4W Carbon
A30410k Ohm, 5%, 1/8W Carbon319203X6500-16810 Ohm, +6%, /8W Carbon
A305203x6501-241330k Ohm, =5%, 1/8W CarbonR320203X6500-92718k Ohm, +5%, 1/8W Carbon
A306203X6500-845,1k Ohm, £5%, WW Carbona21203X67$80 Ohm, =5%, 1/2W Carton
A307203X6500-68915k Ohm, = 5%, v8W Carbon322203X9100-12122 Ohm, = 5%, 2W M.O.
R309203X6500-7242.2k Ohm, = 5%, 1/8W Carbon323203%6500-6891.5 Ohm, 25%,/8W Carbon
R310203x6601-285470k Ohm, #5%, 1/8W CarbonR924203X6500-98827k Ohm, +5%, 1/8W Carbon=
R311203X6501-065,88k Ohm, = 5%, 1/8W CarbonR325203%6500-32647 Ohm, £5%, GW Carbon
R312203X6501-126100k Ohm, = 5%, 1/8W CarbonR328203X6500-628‘Ohm, 25%, 1/8W Carbon
A313,203X6001.32810k Ohm, ‘= 5%, 1/8W CarbonR330203X6500-888,10 k Ohm, #5%, 1/8W Carbon
R318203X6001.04447k Ohm. 5%, 1/8W CarbonR331203x6501.209220k Ohm, = 5%, 1/8W Carbon
R318203X6500628820 Ohm. #5%, 1/8W CarbonRast203x6500-72422k Ohm, £%, VW Carbonmm
Page 26
  • CT

C

C

on

C

c VERT/HOR BOARD (CONT,)

Rot. No.Part No.DescriptionRet. No.Part No.Doseription

RESISTORS (CONT) CAPACITORS (CONT)

382203X8500-92715k Ohm, + 8%, 1/8W Carbon358203x0040-0134.7 UF, 180V Electrolytic
389203X6500.04418k Ohm, 25%, VW CarbonC360202X7000-4820.01 uF, SOV, + 10% Ceramic
3s4209X8500-7833.9 Ohm, 25%, 1/8W Carbon361203X1100-5090.016 uF, SOV, + 10% Mylar
F355203X8500-80212k Ohm, 5%, t/8W Carbon36210 uF, SOV Electrolytic
R36203X6500-561470 Ohm, + 5%, 1/8W CarbonC363203X1205-4870.01 uF, 630, = 10% PP
R357203X8500-7242.2k Ohm, =5%, 1/BW CarbonC364202K7000-4820.01 uF, SOV, ‘* 10% Ceramic
R35848Lak Ohm, £546, YEW Gardon

R359 203X8501; , £5%, 1/8W Carbon

Reoguss00 47127 Ohm, 28%, HW C CeroonSEMICONDUCTORS
.2kOhm, £5%, 1nR301200X4082-614Transistor, 258260
R3631.2k Ohm, 5%, V8W CarbonTR302200X3174-008Transistor, 28617400
R364203X9014-98847K Ohm, £5%, W MO.TR303200X3174.008
36s,58k Ohm, 5%, 1/2W CarbonTR304200X3174.008
R366203X6001-1483.3k Ohm, % 5%, 8W CarbonTR305200X4049-081Transistor, 2SA490YLEGLI
R367940X2222.7342.2k Ohm, 5%, 1/2W Carbon‘TR308200X3162-538Transistor, 2SC1625YLBGLI
R368203X6500-7853.9k Ohm, +5%, /8W Carbon‘TR307200X3174-014Transistor, 2SC1740A
R369203X6500-7623.3k Ohm, + 5%, 14W CarbonTR3O8200X3174-006Transistor, 25017400
R370302X6100-9811k Ohm, +5%, 14W CarbonTR351200X4085-415,Transistor, 258540
R371203X6104-7512.7k Ohm, # 5%, 14W CarbonTAI52200X3172-208Transistor, 25C1722BKS
383340x2222.0342.2k Ohm, £5%, 4W CarbonTR353200X3174.008Transistor, 28617400
Res340X2822.93482k Ohm, 5%, WW CarbonTR3S4200x4082.614Transistor, 2260
VR301204X2122.093Varistor, 260k Ohm, Vert, Holdx301201X2010-144Diode (Si) 182473-172
vR302204X2114-065Vatistor, 20k Ohm, Vert. Sizex302201x2010-144Diode (SI) 1S2473-172
vR351204X2114.059Varistor, 50k Ohm, Hor, Holdx303200X8000-028Diode (GE), IN6OTVGL.
ans2ovK2010-165Diode (i Ise1

1X2010-1 (Sl) 1SS8t

CAPACITORS308201X2010-165Diode ($1) 18881
301203X1100-8280.15 uF, SOV, # 10% Mylarx307200x8010-102Diode (SI) MAZEW
C302203X1100-5730.022 uF, SOV, + 10% Mylarx08200x8010-094Diode (SI) 182473
0304203X1100-8580.1 uF, SOV, + 10% Mylarx351201X2010-144Diode (SI) 1S2473-T72
6306203x0025-0262.2 uF, 50V, Electrolyticx352201X2010-144Diode (SI) 182473-172
307203x1100-9280.15 uF, SOV, + 10% Mylarx353201X2010-144Diode (S!) 182473-772
6309203X1100-8580. uF, 80V, + 10% Mylarxa54201X2010-144Diode ($1) 182473-172
C310203x0010-01122 uF, 18V ElectrolyticX355200x8220-851Diode Zener) ROVE!
3111000 uF, 35V ElectrolyticX366200X8100-130Diode (HS) RU-1 0.3 US

312 (2.0082 uF, SOV. = 10% Ceramic

C313203X0025-087‘47 uF,lectrolytic
C315203X0015-08210 uF, 25V ElectrolyticMISCELLANEOUS
C316203X1100-2203300 uF, 50V, + 10% Mylar3301204X9300-958‘Socket, 6 Pin
C3172028000618100 pF. 50V, * 10% Ceramic3302204x9300-858Socket. 6 Pin
351202X7000-2811500 pF, SOV, + 10% Ceramic301204X9601-195Plug. 6 Pin
352202X7000-2471000 pF, SOV, + 10% Ceramic302204x8801-195Plug, 6 Pin
353203K1100-5730.022 uF, SOV, = 10% MylarTH301201X0000-534Thermistor
C355203X1100-8580.1 UF, SOV, = 10% Mylar
6356203X0015-1054.7 uF, 25V Electrolytic
C357203X1201.0130.015 uF, 200V. = 10% PPTRANSFORMERS &COILS
C358203x1201.0340.018 uF, 200V, 2 10% PPL351201%5200-091Coll, Horie. Ose.

POWER BOARD RESISTORS SEMICONDUCTORS

Aw R501204X1725-052180 Ohm, + 10%, 15W WWTRSON200x3174-008Tranalstor, 25617400
ASO203X6000-608100 Ohm, 5%, 18W CarbonA®TRSOZ200X3145-404Transistor, 2601454
R503203X6000-9601k Ohm, £5%, VW Carbonx501201x2230-.042Diode, (SI) Zener EQB01-08V
504203x6000-879860 Ohm, =5%, 1/8W Carbon502201K2010-144Diode. (Si) 182473-772
SOS,203x9014-9653K Ohm, £5%, TW MO.

S08 im, 5%, VBW Carbon

R5012042050001Varistor Volt Adj.MISCELLANEOUS
‘501204x9300-958Socket. 6 Pin
P501204X9801-195ug, 6 Pin
CAPACITORSTHEOL2010000818‘Thermistor

cs01 10 UF, 160V Electrolytic

C5022811500 pF, SOV. + 10% Ceramic
C503203K0010-01122 uF, 18V Electrolytic

NECK BOARD RESISTORS RESISTORS (CONT.)

R6017091.8k Ohm &5% 1/8W CarbonRa10+203X8500-8004.7k Ohm #5% 1/8W Carbon
ao2203X€500-709118k Ohm + 8% 1/8W CarbonRav203X6500-8004.7k Ohm 5% 1/8W Carbon
agg203%6500-700118k Ohm = 8% 1W CarbonRa12203%9104-80912k Ohm £5% 2.0W Metal Oxide
R404203X6500-447150 Ohm +5% 1/8W CarbonR413203x9104-60912k Ohm *5% 2.0W Metal Oxide
R405,203x6500-481220 Ohm #5% 1/8W CarbonRaid203x9104-80912k Ohm 25% 2.0W Matal Oxide
‘R406203X6500-447150 Ohm + 5% 1/8W CarbonR415203X5601-3132.7k Ohm 2 10% 1/2W Comp.
R407340X2391-934390 Ohm #5% 1/4W CarbonRAB203X5601-3132.7k Ohm 2 10% W2W Comp.
R608340X2391-934380 Ohm + 5% 1/4W CarbonRai7203X5601-3132.7k Ohm + 10% 1/2W Comp.
Raog47k Ohm #5% W8W CarbonRaw203Xx5602-254470k Ohm = 10% 1/2W Comp.
Page 27

19” COLOR MONITOR SCHEMATIC DIAGRAM

MODELS 19K4625, 19K4626, 19K4675, 19K 4676

* Power Supply Voltage and Symbols

Working Circuit

Vert — Drive stage ABL — Bias

CRT Cut-Off

Symbols | Line Voltage

15V

Vert Output Side pin Trans. — Bias 30V

Horiz Osc. Honz. Drive 127V | Horiz Output 160V Video Output

g90V Screen-Bias

Te82 6OHZ

TPB3 15 734 Hz

[amaze te] € 60H TPB4 15.734 Hz VRBee yn TROD © | BL On Gacy rien EM: mon HERR | Elasgg Hotness 30 SERVICE TECHNICIAN WARNING SF Ul D F X-RAY RADIATION PRECAUTION: Sa Ace. SALES UNIAD COW REPLACE SAFETY CRITICAL COM- PONENTS ONLY WITH MANUFAC- TURER’S RECOMMENDED PARTS. AVERTISSEMENT: POUR MAINTENIR LE DEGRE DE SECURITE DE L’APPAREIL NE REMPLACER LES COMPOSANTS DONT LE FONCTIONNEMENT EST CRITIQUE POUR LA SECURITE QUE PAR DES PIECES RECOMMANDEES PAR LE FABRICANT. THIS PRODUCT CONTAINS CRITICAL ELECTRICAL AND MECHANICAL PARTS. ESSENTIAL FOR X-RAY RADIATION PROTECTION FOR REPLACEMENT PURPOSES, USE ONLY TYPE PARTS SHOWN IN THE PARTS LIST.

VERTICAL RASTER POSITION ADJUSTMENT OSCILLOSCOPE WAVEFORM PATTERN The waveforms shown are as observed on the wide band oscilloscope with the monitor turned to a reasonably strong signal and a normal picture. The voltages shown on each waveform are the approximate peak amplitudes. The frequency accompanying each waveform indicates the repetition rate of waveform not the sweep rate of the oscilloscope. If the waveforms are observed on the oscilloscope with a poor high frequency response, the corner of the pulses will tend to be more rounded than those shown and the amplitude of any high frequency pulse will tend to be less.

F 60H

& if ts ware ip PROTECTOR ® TASS TRSS4 250028 /*OR, G 60H 25c1MO/ 2SCIMS ZSAI019 /eSaaze fs

K 15734 Hz Boation on

“WER RUBIO Fe BOARD.

aeirze PA] eset Benes Go Bees Sadso, BUR: K4625C, K4626C, K4675C, K4676C- 5816

Page 28

A 6OHz

0 76vo-p

B 60 Hz

8 4Vp-p

Cc 60Hz

15Vp.p

D 60H

m = 085Vp-p

j

F 60 Hz

VN

H O15 734Hz 4 4Vp-p

20Vp-.

1 15 734Hz

K 15734 Hz TP81 60H?

a

ak

TPB2 60 Hz

a = a

TPA3 15734 He

e a s

TPB4 15 734Hz Power Supply Voltage and Symbols * A

Symbols | Line Voltage 19” COLOR MONITOR SCHEMATIC DIAGRAM

MODEL 19K4677

OSCILLOSCOPE WAVEFORM PATTERN The waveforms shown are as observed on the wide band Working Circuit

CAUTION: FOR CONTINUED SAFETY, REPLACE SAFETY CRITICAL COM- PONENTS ONLY WITH MANUFACoscilloscope with the monitor turned to a reasonably strong signal and a normat picture. The voltages shown on each waveform are the approximate peak ampli- Vert — Drive stage '5V | aBL — Bias CRT Cut-Off X-RAY RADIATION PRECAUTION:

THIS PRODUCT CONTAINS CRITICAL TURER'S RECOMMENDED PARTS. |= AVERTISSEMENT: POUR MAINTENIR LE DEGRE DE SECURITE DE L'APPAREIL Vert Output Side pin Trans. — Bias tudes. The frequency accompanying each waveform indicates the repetition rate of waveform not the sweep gov ELECTRICAL AND MECHANICAL PARTS

_ ESSENTIAL FOR X-RAY RADIATION PROTECTION / FOR REPLACEMENT PURPOSES, USE Horiz Osc Horiz Onive Horiz. Output NE REMPLACER LES COMPOSANTS DONT LE FONCTIONNEMENT EST CRITIQUE POUR LA SECURITE QUE PAR rate of the oscilloscope. If the waveforms are observed on the oscilloscope with a poor high frequency response, the corner of the DES PIECES RECOMMANDEES PAR LE FABRICANT. Video Ourput ONLY TYPE PARTS SHOWN IN THE puises will tend to be more rounded than those shown e

®

© e and the amplitude of any high frequency pulse will Screen-Bias tend to be less.

INTERFACE BOARD P318

VERTICAL RASTER POSITION ADJUSTMENT SENTER al Séhwce Tie we

pgs

neue PROTECTOR Tayse 254075 # SADT 254826 A353 2scimo/ 25010152

sor 288 ng Tain S

ages ascisa Faery Feared Basso. vee Bea. HE €. Esetpdo K4677C-5818 saa Baby

Page 29

C_

C~

C—

C

C—

Hl ty

|: t NECK BOARD (CONT.)

Ret. No.Part No.DescriptionRef. No.

RESISTORS (CONT)

A419203XS602-185,330k Ohm + 10% 1/2W Comp.
422203x9105-1171.0 Ohm s 10% 2W Metal Oxide‘Tria0i
R423203X5102-155270 Ohm = 5% WaW CarbonLied
vRao1204x2115.014800 Ohm Varistor A DriveTRa02
‘VR402(204X2115-014500 Ohm Varistor B Drive
vR4o3208x2115-0085k Ohm Varistor A CutoffTRa03
‘VR404204X2115-006‘5k Ohm Varistor G Cutoff
VRI405204x2115-008,5k Ohm Varistor B Cutoffx404
R408204x2000-025,1M Ohm Varistor Screenx405

X408 CAPACITORS

aot202X7000-2471000 pF. SOV, 10% Ceramic
caoz202x7000-2471000 pF, 50V, 10% Ceramic
403202x70002471000 pF, 50V. 10% Ceramic
C404202x7100.0191500 pF, 2kV' & 10% Ceramicaot
C405202x7 150-018100 pF. 12kV, # 10% CeramicJae
40601 uF, S00V, = 10% CeramicPao
407202x7110.0191500 pF. 2kV, = 10% CeramicP402

C408 68 pF. SOV. = 10% Coramic

cag+202x8000-55068 DF. SOV. # 10% Caramic
ato202x8000-55068 pF. SOV, = 10% Caramic

88052088 R210 Ra R212 R213 Rai R215 R216 R217 R218 R219 PERREEEEA GSS 4% 297X2000-072 HIGH VOLTAGE ASSEMBLY (T701) 204X 1625-058 204X3901-125 6.8. Ohm, = 10% 1SW WW Resistor Focus Control Diode (S! HV) | Diode (SIV) | Part of T701 Dioge isi HV) | 4 We 08x.0129-506 98A8854-000 +205x9800-256 4% 202X1110-810 '208X2000-846 Part No. Description

SEMICONDUCTORS 200x3208-800 Transistor, 2562068, 2801514 (Routputy 200x3206-800 Transistor, 25C2068, 2601514 (G output) Transistor, 26C2068, 26C1514 200X3208-800 (8 output) 201x2100-126 Diode. 182367 (protecton 201X2100-126 Diode, 1S2367 (protector 201x2100-126 Diode. 182367 (protector)

MISCELLANEOUS 208X5003-729 Socket, § Pin Socket, 3 Pin 204Xx9800-329 Plug, 5 Pin 204X9800-254 Plug. 3 Pin

FINAL ASSEMBLY PARTS 19VJTP22 Pix Tube Assy. Purity Shtd/Degaussing Lateral/Purity Assembly Yoke, Deflection CRT Socket HV Unit (T701) Plug, Line Cord (K4625, K4678, (4677) Prag. Line Cord (K4626, K4676) Oegaussing Coil (L701) 297X2000-072 6A0396-001 €A0402-001 9A2753.003

INTERFACE FACE BOARD (P317)

RESISTORS

340x3910-09491. Ohm £5%, 1/2W Carbonoe
340X2223-03422k Ohm = 10%, 1/4W Carbon203
340X3102-6341k Ohm +5%, 1/2W CarbonC208
340X2101-634100 Ohm £5%, 1/4W CarbonC205

340X2104-004 100k Ohm 5%, 1/4W Carbon 340X3331-044 330 Ohm + 10%, 1/2W Carbon 340X2222-634 2.2k Ohm £5%, 1/4W Carbon 22k Ohm £5%, 1/4W Carbon TR201

340X2106-936100k Ohm £5%, 1/4W CarbonTR202
340X2101-934100 Ohm £5%, 1/4W CarbonTR203
340X2471-034470 Ohm #5%, 1!4W CarbonTR204
340X2471-634470 Ohm 25%, 14W CarbonTR205
340X2471-036470 Ohm = 5%, 1/4W CarbonTR206
340X2151-034180 Ohm 25%, 14W CarbonTR207
340X2151-936150 Ohm 28%, 1/4W CarbonTRIB
940X2151.034150 Ohm 25%, 1/4W CarbonTR209
‘340X2101-034100 Ohm 25%, 1/4W CarbonTR210
340X3102-8941k Ohm +5%, 12W Carbonx201
'340%3102-0341k Ohm 25%, /2W Carbonx202
'340X3681-034680 Ohm, 5%, /2W Carbonx203
‘340X3271-034270 Ohm, 5%, /2W Carbonx208
340X3271-934270 Ohm, 5%, 1/2W Carbonz0201

340X2104-094 100k Ohm, 8%, 1/4W Carbon 340x3102.634 1k Ohm, 5%, 172W 340X2822-034 2k Ohm, 5%, 1/4W Carbon

340x2822-69482k Ohm, 5%, 1/4W Carbon4201
340x2822-6948.2k Ohm, 5%, 1/4W Carbon202
340X9991-034390 Chm, 5%, 1/2 W CarbonP203
40X0641-00541.5k Ohm Black Laval Controt204
40X0641-00810k Ohm Horizontal Centering205

CAPACITORS 45x0524098 1000 uF, 16V Electrolytic 48X0524-053 470 uF, 16V Lytic 349X2232-109 .022 uF, 10%, 100V 80X0098-020 660 pF, 10%, Z5F 349X1032-109 01 uF, 10%, 100V SEMICONDUCTORS 86X0113-001 Transistor (NPN) 2N3904 86X0113-001 Transistor (NPN) 2N3904 Pectiee Led Transistor (NPN) 2N3904 ‘Transistor (PNP) MPS-A7O savas an Transistor (PNP) MPS-A70 Transistor (PNP) MPS-A70 soxorisa0t Transistor (NPN) 2N3004 88X0113-001 Transistor (NPN) 2N3904 88X0113-001 Transistor (NPN) 2N3904 66X0113-001 ‘Transistor (NPN) 2N3904 66X0046-001 Dlode Siticon FOH-444 66X0046-001 Dloda Silicon FDH-444 66X0048-001 Olode Silicon FOH-444 66X0048-001 Olode Silicon FOH.444 66X0040.019 Diode, Zener 3.9V, 5%, 0.5W IN52288 MISCELLANEOUS 204X8300-958 Socket, 6 Pin 204X9300-958 Socket, 6 Pin 206X9600-845 Plug, 4 Pin 6A393.003 Plug, 3 Pin 6A0303-006 Plug. 6 Pin

Page 30

Ret. No. INTERFACE BOARD (P318)

OsscriptionRot. No.Description

RESISTORS « CAPACITORS

20145x05240381000 uF, 16V Electrolyti

340%3910-934 91 Ohm # 5%, 1/2W Carbon y lectrotytic

340x2223-93422k Ohm10%, 1/4W CarbonGass45X0524.053470 uF. 16V Lytle
340X3102.9341k Ohm5%, 1/2W Carbon208349x2232.109022 uF, 10%, 100V
'340X2101-934100 Ohm = 5%, 14W CarbonC20580x0099-020680 pF, 10%, Z5F
340X2104-934100k Ohm = 5%, 14W Carbon349K1092-10901 UF, 10%, 100V

340X3331.944 330 Ohm = 10%. 1/2W Carbon 340X2222.934

340x2222:9342.2k Ohm 5%.1/4W CarbonSEMICONDUCTORS
340X2104.934100k Ohm 5%, 1/4W CarbonTR20186X0113-001Transistor (NPN) 2N3904
340X2101.934100 Ohm 25%, 1/4W CarbonTR20288X0113-001‘Transistor (NPN) 2N3904
340X2201-934200 Ohm 5%, 1/4W CarbonTR20386X0113-001Transistor (NPN) 2N3904
340x2201.934200 Ohm =5%, 1/4W CarbonTR204‘86X0086-001‘sistor (PNP) MPS-A70
340x2201.934200 Ohm = 5%, 1/4W CarbonTR205‘88X0086-001Transistor (PNP) MPS-A70
340X2201.934200 Ohm = 5%. 1/4W CarbonTA20686X0086-001Transistor (PNP) MPS-A70
340x2201.934200 Ohm 25%. 1/4W CarbonTR20788X0113-001Transistor (NPN) 2N3904
340x2201.934200 Ohm =5%, 1/4W CarbonTR20888X0113-001Transistor (NPN) 2N3904
340X2101.934400 Ohm5%, 1/4W CarbonR20986X0113.001Transistor (NPN) 2N3904
340X3102.9341k Ohm #5%, V2W CarbonTR21086X0113-001Transistor (NPN) 2N3904
340x3102.9341k Ohm #5%, 1/2W Carbonx20168x0046-001Diode Silicon FDH-444
340X3102.9341k Ohm, 8%, t/2W Carbonx20268x0046.001Diode Silicon FDH.444
340X3471.934200 Ohm, 5%, 1/2W Carbonx20366x0046-001Diode Silicon FOH.444
340X2201-934200 Ohm, 5%, 1/2W Carbonx20468X0046-001Diode Silicon FOH-444
340X2104.934100k Ohm, 5%, 1/4W Carbon2020168x0040.019Diode, Zener 3.9V. 5%, 0.5W
340X3681.934680k Ohm, 5%, 1/2W Carbon1N52288

340x2822-934 82k Ohm, 5%. HW Carton 340X2822.934 hm, 5%, 1#4W Carbon

340X2822.8.2k Ohm, 8%. 1/4W CarbonMISCELLANEOUS
340X3301-934390 Ohm, 5%, 1/2W Carbon20204Xx9300.958Socket, 6 Pin
40X0841-0051.5k Ohm Black Level Contro!J202204x9300.958,Socket. 6 Pin
40X0841.00610k Ohm Horizontal CenteringP203204x9600.845Plug, 4'Pin
2086A303-003Plug, 3 Pin
2086A0393-008Plug. 6 Pin

REAR CHASSIS CONTROLS

HORIZONTAL ‘OSC. COIL (L381)

Focus

RASTER POSITION HORIZONTAL WIDTH COIL ono , hae a /f NEG. H sync

a a VERTICAL, : _—- HORIZONTAL —- HOLO \ eer HenzonTaL watt VIDEO a omgeay POSITION POSITION

FIGURE 17

WGEC SERIES K4600 69% 1090-100

Page 31

NAUGHTY BOY

PARTS LISTS Da Ha D DT Da DV aa aa aoa aS ao lS)

Page 32

Cc Co

c

C

C

C7

i

om PARTS LIST NAUGHTY BOY TOP ASSEMBLY

DESCRIPTION

Assy, Fluorescent Lamp CINEMATRONICS PART NUMBER

38-10640-01

01-10505-01 Lamp, Fluorescent 26-10588-01 Fixture, Lamp, Fluorescent 87-11668-01 Assy, Harn Fluorescent Lamp 25-10579-01 Ty Rap, W/O Eyelet 25-10580-01

34-11271-01

35~10614-01 Ty Rap, W/Eyelet Wire, 18AWG, Twtd, Blk/Wht Pin, Male, Molex

Assy, Coin Meter Meter, Coin 6 Volt (KEISU NR-06) Pin, Male, Molex 29-11754-01

35-10614*+01

20-10896-11Coin Door W/Lamps Cocktail1
22-10899-01Decal, "Cinematronics"1
25-10556-01Nut, Hex #4-403
25-10570-01Washer, Lock #4 Internal3
38-11702-02Assy, Coin Meter/Vol Ctl1
20-10868-11Brkt, Short Vol. Cntl/Counter1
25-10557-01Nut, Hex #6-322
25-10563-01Screw, Machine, #6-32 x 1/2" Pan Hd P2
25-10571-01Washer, Lock, #6 Internal2

38-11757-01 1

38-10961-04 Assy, Vol Ctl 26-10589-01 Knob, Volume 51-10722-01 ‘Pot, W. Lk. Wsr/Nut, 10K Ohm 87-10955-01 Assy, Har, Vol Ctl 34-11719-01 Wire, 22AWG Blue/Red/Blk Twist 35-10614-01 35-10615-01 Pin, Male, Molex Pin, Female, Molex a ale me

87-11680-01 Assy, Harn Coin Door 35-10579-01 | Ty Rap, W/O Byelet 25-10905-01 Clamp, Cable 3/16", Plastic 34-10597-01 Wire, 22AWG, Blk 34-10599-01 Wire, 22AWG, Yellow 34-10603-01 Wire, 22AWG, Grey 34-10906-01 Wire, 22AWG, Twisted, Brown/White 41-10885-01 Conn, 9 Cir F, Molex 03-09-2092

29°

Page 33

PARTS LIST NAUGHTY BOY TOP ASSEMBLY

CINEMATRONICS DESCRIPTION QTY. PART NUMBER

38-11434-01Assy, Monitor, Color Rasteri
87-11711-01Assy, Harn Raster Mon to CPUi
34-10597-01Wire, 22AWG, Blk2

34-10606-01 Wire, 22AWG, Red 34-10598-01 Wire, 22AWG, Green 34-10605-01 Wire, 22AWG, Blue 34-10607-01 Wire, 22AWG, White

35-10614-01Pin, Male, Molex5
35-10615-01Pin, Female, Molex7
41-10954-01Conn, 6 Cir F, Molex 03-09-20621
41-10651-01Conn, Female Crimp Term, Molex1
41-11724-01Conn, 6 Cir Crimp Term 09-50-70611
25-10579-01Ty Rap, W/O Eyelet3
38-11737-01Assy, Circuit Panel1
38-11733-02Assy, Boards W/Vol Mod1
38-11738-02Assy, Board MT-09 W/Vol Mod1

34-10594-01 Wire, 30AWG, Blue, KYNAR

63-10781-01Cap, .0O0Smf SOV DISC 20%1
38-11738-01Assy, Board MT-091
38-11739-01Assy, Board MT-101
20-11687-01Plate, Mntg Logic/Audio1,
25-10557-01Nut, Hex #6-324
25-11756-01Screw, Machine #6-32 x 2" PH PN4
25-11752-01Washer, #6 Lock (Split Ring)4
25-11753-01Spacer, Nylon #6-5/8" (Smith 4025)8
25-11749-01Washer, #6 Flat4
32-11736-01Cabinet, Upright Color Raster SH1
38-11673-01Assy, Ctl Pnla

20-11673-01 | Ctl Pnl 1

22-11674-01Decal, Ctl Pnl1
37-11192-01Button, Short, White, Cocktail2
37-11192-02Button, Short, Red1
Page 34

i

= i a

C

C

  • Co

C

Cc

i PARTS LIST NAUGHTY BOY TOP ASSEMBLY

CINEMATRONICS DESCRIPTION QTY. PART NUMBER

37-11373-01Switch, W/Plastic Mntg Brkt, Short3
25-10559-01Nut, Pal 5/8"3
25-10558-01Nut, Hex, #10-244
25-10572-01Washer, Lock, #10 Internal8
25-10909-01Bolt, Carriage, 3/16" x 3/4", Blk OX4
50-11763-01Assy, Joystick 4 Pos WICO 15-95181
25-11688-01Screw, Machine 8-32 x 1/2"4
87-11679-01Assy, Harn Ctl Pnli

34-10596-01 Wire, 22AWG/TC, Buss 34-10597-01 Wire, 22AWG, Blk 34-10607-01 Wire, 22AWG, White 34-10598-01 Wire, 22AWG, Green 34-10600-01 | Wire, 22AWG, Purple 34-10599-01 Wire, 22AWG, Yellow 34-10603-01 Wire, 22AWG, Grey 34-10604-01 | Wire, 22AWG, Brown 34-10605-01 Wire, 22AWG, Blue 34-10602-01 Wire, 22AWG, Orange

35-10614-01Pin, Male, Molex9
41-10885-01Conn, 9 Cir F, Molex 03-09-20921
25-10579-01Ty Rap, W/O Eyelet8

23-11152-01 Tape, Foam 3/4"

38-10894-01 Assy, Coin Drawer

20-10862-01 20-10864-01

20-10871-01

20-10872-01 Brkt, Coin Box Tong Handle, Coin Box Coin Box

Cover, Coin Box whee ele

38-11700-01 Assy, P.S./Transformer (Raster)

20-11606-01

25-10551-01 25-11607-01 25-11612-01 25-11613-01 Plate, Mtg, P/S, Transformer Bolt, Carriage, 3/16" x 1/2" Black O Stand-Off, Nylon, Locking, DLCBS-14 Washer, Lock #8 Nut, #8-32 oonaor |r

Page 35

CINEMATRONICS PART NUMBER

38-11723-01

43-11704-01

87-11688-01

87-11768-01

87-11767-01

81-11685-01

20-10520-01

20-10521-01

25-10556-01

25-10570-01

25-10974-01

41-10661-01

53-10732-01

53-10734-01

53-11707-01

63-10784-01

63-11128-01

65-10812-01

66-11705-01

66-11706-01

80-11685-01

82-10842-30

38-10638-01

20-11382-01

71-10834-01

87-11681-02

87-11681-01

34-10597-01

34-10598-01

34-10599-01

34-10600-01

34-10602-01

34-10603-01 PARTS LIST NAUGHTY BOY TOP ASSEMBLY

DESCRIPTION

Assy, Transformer ISOL Ravenswood Transformer, ISOL Ravenswood Assy, Harn Trans/Monitor

Assy, Harn Trans/P.S. Assy, Harn Trans Gnd. PCA, Regulator +12V, -5V Heat Sink, Thermalloy 6071B Heat Sink, Thermalloy 6072B Nut, Hex #4-40

Washer, Lock, #4 Internal Screw, Machine 4-40-3/8" Pan HD PH Conn, 6 Cir WAF, Molex 09-18-506

470 Ohm 1/4W 5% C 1K Ohm 1/4W 5% C 150 Ohm 5W Ceramic "Block"

-lmf 50V Disc 20%

22mf 50V Electrolytic Radial Diode, 1N4003, Encpl Trans, 7812

Trans, 7905

PCB, Regulator +12V, -5V Power Supply, Data Power

Assy, Speaker

Grill, Speaker Speaker

Harn Main W/Conn

Harn Main

22AWG, Blk

22AWG, Green 22AWG, Yellow

22AWG, Purple 22AWG, Orange

22AWG, Grey PPP Pew eWve PP be een vfelele le re

we le es ee ee |

Page 36

i

i

Cc

i

‘a

om

i

C

Cc 34-10604-01 Wire, 34-10605-01 Wire, 34-10606-01 Wire, 34-10607-01 Wire, 34-10608-01 Wire, 34-10610-01 Wire, 34-11407-01 Wire, 35-10614-01

35-10615-01

41-11746-01

41-10649-01

41-10648-01

41-10883-01

41-10647-01

41-10657-01 Conn,

Conn, Conn, Conn, Conn,

87-11677-01

34-10597-01 |Wire, 34-10607-01 Wire, 34-10598-01 Wire, 34-10600-01 Wire, 34-10599-01 Wire, 34-10603-01 |Wire, 34-10604-01 |Wire, 34-10605-01 |Wire, 34-10602-01 |Wire, 35-10615-01

41-10660-01

41-10649-01

25-10579-01

25-10580-01 Conn, PARTS LIST NAUGHTY BOY TOP ASSEMBLY

22AWG, 22AWG, 22AWG, 22AWG, 18AWG, 18AWG, 18AWG, CINEMATRONICS DESCRIPTION or PART NUMBER

Brown

Blue

Red

White

Red

Black

Yellow

Pin, Male, Molex Pin, Female, Molex Conn, Edge 36P Sullins EZM18DSEH 9 Cir M, Molex 03-09-1093

15 Cir F, Molex 03-09-2153

3 Cir M, Molex 03-09-1038

12 Cir M, Molex 03-09-1122 6 Cir M, Molex 03-09-1063

Assy, Harn Ctl Pnl Interface

22AWG, 22AWG, 22AWG, 22AWG, 22AWG, 22AWG, 22AWG, 22AWG, 22AWG, Pin, Female, 15 Cir BLK

White

Green

Purple Yellow

Grey Brown

Blue

Orange Molex

M, Molex 03-09-1152

Conn, 9 Cir M, Molex 03-09-1093 Ty Rap, W/O Eyelet Ty Rap, W/Eyelet w

wanrr

Page 37

PARTS LIST NAUGHTY BOY TOP ASSEMBLY

CINEMATRONICS DESCRIPTION QTY. PART NUMBER

87-11755-01

34-10597-01

34-10599-01

34-10600-01 34-10606-01

34-11719-01 Assy, Harn Coin Door Inter. Raster

Wire, 22AWG, Blk Wire, 22AWG, Yellow Wire,22AWG, Purple Wire, 22AWG, Red Wire, 22AWG Blu/Red/Blk Twist 41-10885-01 Conn, 9 Cir F, Molex 03-09-2092 1 41-10649-01 Conn, 9 Cir M, Molex 03-09-1093 1 35-10614-01 Pin, Male, Molex 9 35-10615-01 Pin, Female, Molex 7 25-10579-01 Ty Rap, W/O Eyelet 5 25-10580-01 Ty Rap, W/Eyelet 2

87-11701-01 Assy, AC Power Cord Harn i 25-10561-01 | Nut, Wire 1 25-10579-01 | Ty Rap, W/O Eyelet 15 25-10580-01 |Ty Rap, W/Eyelet 5 34-10608-01 Wire, 18AWG, Red 34-10609-01 Wire, 18AWG, Blue 34-10610-01 Wire, 18AWG, Black 34-10908-01 Wire, 18AWG, Orange 34-11187-01

34-11412-01

34-11718-01

35-10614-01

35-10615-01

35-10617-01

41-10647-01 41-10657-01 41-10884-01 87-10967-01 Wire, Stripe, 18AWG, Red/Black Wire, 18AWG, Brown Wire, 18AWG, Blu/Blk Pin, Male, Molex 14 Pin, Female, Molex Terminal, Female, Quick Disconnect Conn, 12 Cir M, Molex 03-09-1122 Conn, 6 Cir M, Molex 03-09-1063 Conn, 12 Cir F, Molex 03-09-2121 Assy, Cord, AC Power PrPrPP nu os ns cs Se! Pl Pee |

=)

Page 38

C=

a CINEMATRONICS PART NUMBER

87-11692-01

34-10906-01

35-10614-01

35-10617-01

25-10580-01

41-10659-01

38-10892-01

20-10863-01

37-10893-01

20-11376-02

20-11377-02

21-11666-03

21-11694-01

21-11741-02

22-11742-01

25-10553-01

25-10560-01

25-10568-01

25-10551-01

25-11392-01

25-10566-01

25-11613-01

25-11721-01

38-11728-02

18-11732-01

25-10566-01

67-11580-01

67-10832-01 PARTS LIST NAUGHTY BOY TOP ASSEMBLY

Assy, Harn Speaker

Wire, 22AWG, Twisted, Brown/White Pin, Male, Molex Terminal, Female, Quick Disconnect Ty Rap, W/Eyelet Conn, 3 Cir F, Molex 03-09-2038

Assy, Interlock Swt, Back Panel Brkt, Interlock Switch Switch, Interlock

Retainer, Marquee Plexi Upper 23

Retainer, Marquee Plexi Lower 23 Plexi, Front Screened Plexi Smoked 23. 75 x 20

Plexi, Marquee Screened Decal, Side Bolt, Carriage, 3/16" 2", Black OX Nut, Wing, 3/16" #10-24 Washer, Flat, #10 x 1/2"

Bolt, Carriage, 3/16" x 1/2" Black O Bolt, Carriage, 3/16" x 1 1/4", Blk Screw, Wood, #8 x 5/8", Bx Dr Blk, OX Nut, #8-32

Hook, Key

Kit, Spares

Screwdriver, BX DR #8 VACO TR-2 Screw, Wood, #8 x 5/8", BX DR BLK, OX

Fuse, SAMP Slow Blow

Fuse, 5AMP, 3AG

Page 39

CINEMATRONICS PART NUMBER

21-10831-01

22-10542-01

22-10544-01

34-10903-01

35-11096-01

72-11734-01

38-11758-02

15-11179-01

15-11180-01

15-11181-01

15-11759-01

15-11760-01

20-11420-01

21-11715-01

32-11427-01

32-11428-01

32-11556-01

25-11722-01

38-11439-01

25-11414-01

71-10834-01

38-11441-01

20-10871-02

20-10872-02

38-11691-01

20-11691-01

22-11744-01 Assy, Ctl Pnl Plyr #1 PARTS LIST NAUGHTY BOY TOP ASSEMBLY

Bezel, CRT, Formed

Label, "Patent Notice"

Label, “Unit Wired For" Braid, Flat, Tinner Copper, 3/16"

Lug, Ground Manual, Operator

Assy, Shipping Cont. Raster Short

Cap Pads, Corner

Pallet Foam

Sleeve, Game (29x33x72) 600DW Banding, Plastic 3/8"

The following parts are used on the Cocktail Table game cabinet ONLY:

Rail, CRT Mtg Plexi, Smoked Top Cabinet, W/Back Bracket, Glass Holder

Bkt, Speaker Leveler, Leg Assy, Speaker Screw, Wood, #8-1 1/4", BX DR, BLK O

Speaker a a

Assy, Coin Box

Coin Drawer roe |

Cover, Coin Drawer

Ctl Pnl Plyr #1 Decal, Ctl Pnl Plyr #1 arn 2]

as)

Page 40

t~> 7 fe

c-

| en &

C

Cc

ca

~ oe

C

co

oa PARTS LIST NAUGHTY BOY TOP ASSEMBLY

CINEMATRONICS DESCRIPTION PART NUMBER

38-11691-02 Assy, Ctl Pnl Plyr #2

20-11691-02

22-11744-02 Ctl Pnl Plyr #2 Decal, Ctl Pnl Plyr #2

38-11716-01 Assy, Power Supply Raster

20-11709-01 Plate, Mntg P/S & Trans

Assy, Harn Ctl Pnl Inter 87-11710-01

25-10579-01 Ty Rap, W/O Eyelet 25-10580-01 Ty Rap, W/Eyelet 34-10597-01 Wire, 22AWG, Blk 34-10598-01 |Wire, 22AWG, Green 34-10599-01 |Wire, 22AWG, Yellow 34~10600-01

34-10602-01

34-10603-01

34-10604-01

34-10605-01

34~-10607-01

35-10614-01

35-10615-01

41-10648-01

41-10649-01 Wire, 22AWG, Purple Wire, 22AWG, Orange Wire, 22AWG, Grey Wire, 22AWG, Brown Wire, 22AWG, Blue Wire, 22AWG, White Pin, Male, Molex Pin, Female, Molex Conn, 15 Cir F, Molex 03-09-2153 Conn, 9 Cir M, Molex 03-09-1093

87-11708-01 Assy, Harn Ctl Pnl #1

87-11708-02

34-10596-01

34-10597-01

34-10607-01

34-10598-01

34-10600-01

34-10599-01

34-10603-01

34-10604-01 Assy, HarnCtl Pnl #2 Wire, 22AWG/TC, Buss Wire, 22AWG, Black Wire, 22AWG, White Wire, 22AWG, Green Wire, 22AWG, Purple Wire, 22AWG, Yellow

Wire, 22AWG, Grey 22AWG, Brown Wire,

Page 41

CINEMATRONICS PART NUMBER

34-10605-01

34-10602-01

35-10614-01

41-10885-01

25-10579-01

92-11740-01

20-11156-01

23-11425-01 NAUGHTY BOY TOP ASSEMBLY

DESCRIPTION

Wire, 22AWG, Blue Wire, 22AWG, Orange Pin, Male, Molex

Conn, 9 Cir F, Molex 03-09-2092

Ty Rap, W/O Eyelet

Glass, Top Screened Grill, Heat Vent

Tape, Foam 1.5"

Page 42

a

fa

<= f

Cc

Co CL eo Ge rm Um Oo PARTS LIST ELECTRONIC BOARDS

CINEMATRONICS DESCRIPTION QTY. PART NUMBER

38-11733-01 Assy, Boards NB

Assy, Game NB 8201 (NB) 38-11820-01

81-11821-01 Assy, Game NB 8201

36-10621-01

36-11784-01

37-11824-01

44-10679-01

44-10680-01

44-10683-01

44-10689-01

44-10690-01 Socket, 24 Pin, IC Dip Solder Tail Socket, 40 Pin Diptail Switch, Dip 8 Pos DCS5V 1A Uni-Aut Ic, 74LS04

Ic, 74Ls08

Ic, 74L832

Ic, 74LS8157

Ic, 74L8163

44-11028-01 Ic, 74874

44-11029-01 Ic, 74LS138

44-11036-01 Ic, 7407

44-11340-01 Ic, 74L8125

44-11343-01 Ic, LM556

44-11478-01

44-11483-01

44-11486-01 Ic, 74LS153

Ic, 74LS174

Ic, 74LS244

44-11487-01 Ic, 74LS245

44-11492-01 Ic, 74LS374

44-11825-01 | Ic, 74LS14

44-11827-01 Ic, 74LS145

44-11828-01 Ic, LM324

44-11829-01 Ic, LM380

44-11830-01 Ic, 14006B

44-11831-01 Ic, 14066B

44-11832-01 Ic, TMS-3615

44-11833-01 IC, Z2-80A RPP PEP EF EP NNNNNWPE REPKE PE ee wee ee © |

44-11834-01 Ic, 2114/4

RES, 100 OHM 1/4W 5% C RES, 150 OHM 1/4W 5% C $3-10726-01

53-10727-01 a)

Page 43

PARTS LIST ELECTRONIC BOARDS

DESCRIPTION

RES, 330 OHM 1/4W 5% C RES, 470 OHM 1/4W 5% C RES, 1.5K OHM 1/4W 5% C RES, 2K OHM 1/4W 5% C RES, 10K OHM 1/4W 5% C 10 RES, 20K OHM 1/4W 5% C RES, 47K OHM 1/4W 5% C RES, 33K OHM 1/4W 5% C RES, 100K OHm 1/4W 5% C RES, 200K OHM 1/4W 5% C RES, 510K OHM 1/4W 5% C RES, 510 OHM 1/4W 5% C CAP, .Olmf 50V Disc 20% CAP, .00lmf 50V Disc 20% CAP, 47m£ 50V Electrolytic Radial CAP, .Oluf 50V Film CAP, 10m£ 50V Electrolytic CAP, lmf 50V Electrolytic CAP, 2.2mf 50V Electrolytic CAP, 470m£ 50V Electrolytic CAP, .047mf 50V Disc 1

Trans, 2SC-1815 Board, NB-8201

Assy, R. Cble Flat 50 Cir Ic, 74LS136

Assy, E Prom Kit NB-8201 (NB) CINEMATRONICS PART NUMBER

53-10731-01

53-10732-01

53-10735-01

53-10737-01

53-10746-01

53-10749-01

53-10756-01

53-10924-01

53-10928-01

53-10931-01

53-11308-01

53-11836-01

63-10782-01

63-10940-01

63-10993-01

63-11100-01

63-11370-01

63-11837-01

63-11838-01

63-11839-01

63-11840-01

66-11841-01

80-11821-01

87-11842-01

44-11826-01

05-11823-01 e °

ed PPP PP BP PP PEP iP EPP we NUvweet ne neuu

02-11823-01 E Prom, #1 NB 02-11823-02 | E Prom, #2 NB 02-11823-03 | E Prom, #3 NB 02-11823-04 E Prom, #4 NB 02-11823-05 | E Prom, #5 NB 02-11823-06 | E Prom, #6 NB 02-11823-07 | E Prom, #7 NB 02-11823-08 E Prom, #8 NB p

I

to

a |

Page 44

t

Cc Go ft ft hf

t

c PARTS LIST ELECTRONIC BOARDS

DESCRIPTION

Assy, Game NB 8202 (NB) CINEMATRONICS PART NUMBER

38-11820-02

81-11822-01 Assy, Game NB 8202

36-10620-01

36-10621-01

44-10677-01 Socket, 16 Pin, IC, Dip Solder Tail Socket, 24 Pin, IC, Dip Solder Tail Ic, 74LS00

44-10679-01 Ic, 74LS04

44-10680-01 Ic, 74LS08

44-10686-01 Ic, 74LS86

44-10687-01

44-10688-01

44-10689-01

44-10690-01

44-11028-01

44-11029-01

44-11032-01

44-11341-01

44-11487-01

44-11490-01

44-11492-01

44-11826-01

44~-11843-01

44-11834-01

53-10726-01

53-10734-01

$3-11306-01

63-10780-01

63-10790-01

63-10940-01

63-11840-01

69-11844-01

80-11822-01

05-11823-02

02-11823-09

02-11823-10 Ic, 74LS107

Ic, 74L8151

Ic, 74LS157

74LS163

74LS74

74LS138

74LS174

7404

74LS245

748283

74LS374

74LS136

Ic, 6301

Ic, 2114/4 RES, 100 OHM 1/4W 5% C RES, 1K OHM 1/4W 5% C RES, 1.2K OHM 1/4W 5% C CAP, 470PF 50V Disc 20%

CAP, 47mf 50v Electrolytic Axial CAP, .00lmf 50V Disc 208 —

CAP, .047mf 50V Disc

Crystal, 12 MHZ HC-18/U Board, NB-8202 Assy, E Prom Kit NB-8201 (NB)

E Prom, #9 NB

#10 NB E Prom,

4l ran

PRE PP ONY PNP HE ONPWWNNYHNYW ORE ENNN ON

Page 45

PARTS LIST ELECTRTONIC BOARDS

PART NUMBER

02-11823-11

02-11823-12

02-11823-13

02-11823-14

02-11823-15

02-11823-16 Mm 29 co fy

aq 1

i

Page 46

om

C

to or

(

a

{=

Cc.

C EDGE CONN. PIN (J1)

J1-A

J1l-1

J1-B

J1-2

J1-c

J1-3

J1-D

J1-4

J1-E

J1-5

J1-F

J1-6

J1-H

J1-7

J1l-d

J1-8

J1-K

J1-9

J1-L

J1-10

J1-M

J1-11

J1-N

J1-12

J1-P

g1-13

J1-R

J1-14 NAUGHTY BOY

FUNCTION

Ground, Monitor

Ground, Power Supply Ground, Volume Pot

Ground, Connector Switch

Not Used

Ground, Control Panel

Speaker Ground Speaker Output Not Used

Coin Switch

Not Used

Not Used

+12 Volts

+12 Volts

Volume Pot

Volume Pot

+5 Volts

+5 Volts, Counter Not Used

Not Used

Player Two - Up Player One - Up Player Two - Down Player One - Down Player Two - Right Player One - Right

Player Two - Left Player One - Left BOARD EDGE CONNECTOR PIN-OUT LIST

TO

J6-1

J5-1

32-7

J2-1

J3-7

J4-1

J4-2

J3-6

J3-10

J3-4

J3-12

33-2

g3-14

J3-1

J3-15 WIRE COLOR

Black

Black

Black

Black

Black

Black

Brown

Yellow

Yellow

Red

Blue

Red

Red

violet

Violet

Gray Gray Blue

Blue

Orange

Orange

Page 47

EDGE CONN. PIN (J1)

J1-s

J1-15

J1-T

J1-16

J1-U

J1-17

J1-v

J1-18 NAUGHTY BOY

BOARD EDGE CONNECTOR PIN-OUT LIST

FUNCTION

Monitor - Red

Player Two - Start Monitor - Blue

Player One - Start Monitor - Green

Player One ~- Fire Monitor Sync.

Player Two - Fire TO

J6-2

J3-8

J6-4

J3-9

J6-3

J3-11

J6-5

J3-5 WIRE COLOR

Red

White

Blue

Green

Green

Yellow

White

Yellow m io

im

md

a

Go

Page 48

APPENDIX A

Assembly Drawings

Schematics

and

Wiring Diagrams

Page 49

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 50

“|. 30

i

Fy tas -| 308.8

Teak : 5 F J 8

ah Assy

4]

SI

vy omgy re ny Qe Q] .

” N wees | | acade-/0d 278y2 sv74 [0]

x N B + Oy} t iS m % N

x

N BS ~ ~~ Bs ~eatt cl : Uo $

alk un N >

N

%

N _ ig 7 - 229 : | "- A§M660 JAPAN LEISURE CO.. LTD. Tm ee mae to

Page 51

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 52

Ram) ep (__ or POTTS aoe ah bit L

anay ig

SCHEMATIC PG. 2 RAM BOARD ED ¥-<

NB- 8202 ED vers-v0

CID ewn-or m0

GED rav-oe

SLED JAPAN LEISURE CO, LTD]: ED tron

Page 53

2D-waTe-on, >

oa 20-11382-01 4 PLE: (FARSIOE) =I NOTE: 21-11094-01 ah .

WITH Wale NUT

CyvPyeomi snes, phic frie CHPVEOM SIDES,

QIN DOOR ASstY 38-1698 -O1 ee HDC DECAL(2) 22-1742 -O1 CABNET COLOR RASTER (SHORT) 32-11736 -O1

Page 54

POWER SUPPLY ASSY

38-11700-01 ¢SHoMN) es a ao wo Dm aa ae So eee ee ad ae a

Page 55

REGULATOR

BOARD

betel Bl-11GBS-ol Fiwog. Lane

Are heey B2-\"1e0-ol etieee Pe CINEMATRONICS [ie A [oonbr scat owl UPZIGuT (WB)

NOTES: UNLESS OTHERWISE SPECIFIED

Page 56

= PICT ae CoG

Toe [Reon qo [enor [au | Pw [atw [oeakas

go e790 we 2@sn03ecs LSl/oq |x 2 4oare ge adad [dd eddaededee calec let = secce ! elere sree se eg erage Qesealiceelcces saree ges |seese ESSLIELE [ASIA RAR G AR sada | gas Quaassaaanag|g24548

Pyjao‘e.

ated tebgall ieegt] | ual i fe | wai | <i isl Fat r

ial ggentsedtutaeBeatie | Mewtd|

i—Ggeauggd 92 ggsezsddsdagdaagt,y oo {—dnevangaeeasenand bed eveneerededs i.

g—3 998g— 3 g—~3a

Pag

Y—¥ Faet—3 8ky28,
S5—8 SF“te &-———_—§ja2
z,Se rwadit3B ata
iia)Nese Heanliteldlyata fse

FETT)

a ftzuh Sietines SesxaePragessanerageae?
\asssq S38Bssoh 44999498438 54395ey ate

ar 23 sa7agt iserreresrsrretsrrteteerss gle

wetsig3°

Tel ag9 fais 4 a | ARE ® iiss te i/° wo id

  • i

“3

(0 J

one

i oo

i

{o aa

Page 57

) 10-990 67°) TPO | aE

Page 58

fe co ft) Ci oe G31s1D3dS SSIMYSHLO SSI INN ‘SALON ww wy bf SI-ed

vl a er ze S BINiaa°a We ee “212 SI LOWLY SUD any ome

WEL.um 2noNIM azinenessiO wo OzoncONsaY 28 01 10m $1 QuY OM SDINCHAVABNID 40 AmBeOuS 24 G1 1NBANDOD Sid Auvisiudoud

Page 59

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 60

PROPRIETARY

THIS DOCUMENT tS THE PROPERTY

OF CINEMATRONICS INC. AND IS

WOT TO BE REPRODUCED OR

DISTRIBUTED WITHOUT WRITTEN

AUTHORIZATION OF CINEMATRONICS

unc. [connector [FROM | TO | COLOR [ANG]PIN [LENGTHTREMARKS | Ti-1 (VOL) (BLK) (22) (FY Ti 3) -2 COUNTER) 2D (M) 31-3 RLSWMH GRY 22 M INTERERee «oT 3 LPL Swed YELLOW 22M MOLEX # 11-4 (QOUNTER) (22) (M) 03-09-2092 31-5 (OL) (RED) @2) &) Aai-iosss-01 T'-@ WOK) (IE) @Z) (FD T\-7) RESWICH BLK 22 =F 20.0" SWITCH BND Ji-B LAMPI WHT A 22 M = 14.2S' LIGHT J1-8 LAMPZ WHT A M 19.25" LIGHT T1-9, LAMP( = BRN A M 14.25" LIGHT Ti-9 LAMP2 BENA M LIGHT LFT.ANITON RTAWITCN BLY. JUMPER wees el

Axio Be amen AT Net Assent. A STRIP BACK 3/8" FOR SOLDER Z\CINEMATRONICS PART NO. NOTES Mmm reo oa eS OSD oD eee ee eee ass

Page 61

a Sco ¥ [rete cust eco" 173 |

[connector | von [ 7 | cotoe [wenneus [couwector] FRom

t PI-LAY P27 . PI-i PIT PAA PL PI-2 P24 wT / P2 on PI-9 BZOWN PI-2 CRI CaTUOE A-3 YELLOW on a PLS Pld YeLow z tal wie lf a S PLA Geey 03-09-1093 PI-B 2-2 NeLioW 3 03-09-2092 P2-4 0 PI-D wWuite, [A\a-oedgot PI-4 PS EN A A-loB801P2-4 — ¢ZI- Bone i Pl-4 PLS YetL0d P2-5A PI-e zed H PI-4 CRI ANNE P-L A PI-o = Fave P-S,A PIS = 2eD / P2-7 Ay P\-l FARO Pl-G By P21 BAe P2-& = @A-uuché PI-7 74-1 Faacd . + 71-8 Aa zen

1-8 PLB aH 1-9

AR-F Pat SZOwn AY We wees aze TWheten. GTMEWIZE en —

  • comuone SNE -GOD- wom DIONE. - =v ) wirezconnect | A AX civlematzonics ine, AZT No. ss

NOTES: UNLESS OTHERWISE SPECIFIED

Page 62

PROPRIETARY

Pas ZN Aitti4-c\ Pa~o ro Hewes [ad CINEMATRONICS E\ommned ea Z a:

WOLEX PN 02-09-18. A €= cemp reennlaces WOLed PIN 68-50-c10u

A Pil a5-loase-ot. Z\ CINEMATRONICS PART NO.

NOTES: UNLESS OTHERWISE SPECIFIED

ZB Ma Mace PAL,

Page 63

POWER SUPPLY CONECTORS

BOTH Jid J2 AS VIEWED FROM THE FROIUT OF POWER SUPPLY. by 5) cinematronics Peon? eared Fe S| POWER SUDELY wa] YOUT /LLUSTRATION, i re )F*]72-10877-03 2 |e

AY SAMP ILINE CIRCUIT BROKER 082.

Page 64

PROPRIETARY

L@)lt2sv RTN ! -25V,3A Beka

N.___ 1N_ HOUSE moo.

ADD. OF TWO

3 FOR COV OPERATION

SET N5/230V SwiTcH To 115 AND

APPLY AC TO TRANSFORMER

TERMINALS NOS LAND S

2 RECOMMENDED FUSNG: (acaba pare] OWS TITLE BA SLO BLO FOR ISV eee [es] XENTEC POWER SUPPLY A

\.5A SLO BLO FOR 230V S UNUSED COMPONENTS: C85, CRO [DO NOT SCALE OwG] 5] 1 TRANSFORMER SHOWH WIRED POR HISVAC OPERATION p

NOTES: UNLESS OTHERWISE SPECIFIED 4. REF, DRAWINGS: ASSY £921-A01, PCR 2951- Dol

Ta oO ma Da aoa oOo |S wa iN aaa ead

Page 65

| rrr Os Cn Ooms Geil Goats Gate

1 SCHEMATIC SET FOR 1S VAC OPERATION

mOTER eEss OTHERWISE SFECIED

Page 66

Cc! a i om co Ce m1 cot fF Co Co Co

MYST SWMO Me FHV SFM YOLSIST a Tov SUOISIETY Yt Te AOS? ‘GS '¥E 81 BNO BENET voor il ca i LU2

Page 67

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 68

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 69

SJ I LTT a Oe a ee eee

Page 70

PROPRIETARY

” D |] bstmeuren witnour warrran AUTHORIZATION OF COEEMATRONICS

1. A> Vewen FZOM a Wite 4ane.

FEMALE QUICK

DISCONNECTS

(REF) ASSY TRANSFORMER.

MONITOR HARNESS,

c FA 81-1@8B-O1

BLACK £ WHITE TWISTED FAIR, 18 GA

ASSY TRANSFORMER

GAID. HARNESS 87-11767-01 GREEN, 18 GA

81-1768-O1 BLACE € WHITE TWISTED, (6A Tem ee ToNoue,

i NOTES: UNLESS OTHERWISE SPECIFIED Sa es OO De US Dr OOS De ON OO

Page 71

[setae | ____awser s009] nn; V] 1O-BS™-LS Lee “SWI-LO-BO “ON ABW ‘ LeNVEy BIWWaZ =5 7} A Fal aaa

uy on 3 3} Ae 1 POuONTs = LPNS We YUN 207 Wd

\O-MML\-\p "ON “BNID bLOI-bO-b) “ON KSTIOW STW 2 ZL dd

CY) A@-OLLN-S&E_ “ON “BNID OUST ODEN ZO AMINA ‘ON yolkL "73de asLymsmi Al7IAA =OGL" X USO" * aKROT PANS *SvIATs ‘ TIPIWABL-

oa ‘someon 40 KOUYZORINY WELLIUm ANONLIM O2NEIELSIO wo cuancowssy as 02 LOM

Page 72

PROPRIETARY

BPEL. TITON Wo. PUQIFIad ce WNQFlad ems. Wo. SB-lIT2-cl (2) -Plo 4 ae tare Molex No. 03-09- low Cle. No. 4l-lowse-ol aN LeNaTH

coor Aula Bo Puace lB nN Wate 1a w = =

ee eel Sas re NN G lots | MAE — ear sea ors TRANER, ae AuPPY

thocex lo. 02-09-7218. a:

NOTES: UNLESS OTHERWISE SPECIFIED

Lo h= phate oP 4 3 Ce ee a es | I TS) a ee eae

ae ee Se ND |

Page 73

CzvOy 12Or SKINNED,

PROPRIETARY

THIS DOCUMENT iS THE PROPERTY

OF CINEMATRONICS INC. AND IS

NOT TO BE REPRODUCED OR

DISTRIBUTED WITHOUT WRITTEN

AUTHORIZATION OF CINEMATRONICS

anc. TERMINAL , FEMBLE, QUICK DALOMNECT, 087 %.150 RuLLY NSULATES 4PEL. TION No PUALIFIED o2 WN22FIADdD CINE. NO. 3B-\ITT2-el WANK , Zu, ToNave wlize , 1S avy azeed 14.5.0 i , 24- W2713-ol loule-o\ eal ALL SHARP a: W A | soe *AARHEAL, MOAN seeotts. =" [0 Rot Stace owe] TANS C. oy

Page 74

PROPRIETARY “5 Adxanwsr-01 pi -o %. FQD- FEMALE QUICK DVACONNECT 3/Iu.

  • F-FEMME ADCKET 02-09-11. 3 Me MALE OM 02-09-2018.
  • WN- WIRE NUT CONNECTION. Z\ CINEMATRONICS PART NID.

NOTES: UNLESS OTHERWISE SPECIFIED:

03-09-0122 AXai-10047-01 Po -1 PIS-GR GRN 18 Gides\s GND “2 PIS-wT | WHT 18 1 Newt 3B INT.SWITCH RED/BLE 16 1v.0 WB oT

NOT USED

FAD 140 1.0 a oe TRE WIRE. LIST

Page 75

MS VOSt Ms UV OSI N e a a MS VU OSI S. R4 AND RS ARE Y4WATT ,S% CARBON, VALUES 4RE IN OHMS

AS\ ELECTROLYTIC CAPACITOR,

  • 7 SWATH POLARITY MARIC

SZ" AND LOCATION FaR OVERSIZED CAPACITOR

3.C_> 18 A DISK CAPACITOR,

Z. CAPACITOR VALUES ARE IN MICRA FARADS ,SOV

  • ALL DIODES ARE IN4a03

NOTES: UNLESS OTHERWISE SPECIFIED

[mev[_oescrrnon [care] arpngven | Pe rae ee

1TEM NUMBER ON

ENGINEERING

paets LIST

PL 11685 1G@ MARCH 1981

Page 76

PROPRIETARY

THIS DOCUMENT IS THE PROPERTY

OF CINEMATRONICS INC. AND IS

NOT TO BE REPRODUCED OR

DISTRIBUTED WITHOUT WRITTEN

AUTHORIZATION OF CINEMATRONICS:

Inc, *+2sv COM 3 U2 |INq003 1905 B4 ™IN4O03

-25y SOM UNREG, SW CONNECTOR Jl El Cajon INC. $$o20

FINISH: BREAK ALL SHARP EDGES AND DEBURR ALL HOLES. REGULATOR. +12,-S VOLTS: ‘WG JowG NO. ee T2-&BS-00|6 | coo Ewe. [acer tor |

Z.R4 AND RS VALUES ARE IN OHMS

  • R&A AND RS ARE Yq WATE, 5% CARBON NOTES:UNLESS SPECIFIED OTHERWISE TOLERANCE: UNLESS. JOTHERWISE SPECIFIED

EzvOr 12Gr ONINNED

Page 77

PROPRIETARY

‘THIS DOCUMENT 1 THE PROPERTY

OF CINEMATRONICS INC. AND IS

NOT TO BE REPRODUCED OR

OISTAIOUTED WITHOUT WRITTEN AUTHORIZATION OF CIXEMATROHICS

nc,

ASS‘Y BOARD (N.B.)

38-11733-01 INSTALL THIS WIRE. FROM FARSIDE. COMPONENT “—~ soLnee To FIN & GOR 4ne) # PLS (AZ AIDE).

SIDE 2 BOTH SIDES AS SHOWN. USE. BUSSWIRE P/N $4-1059-O1 2 PLACES ercey eicaee $2020 Z\ REMOVE POT FROM VRI LOCATION AND INSTALL ; ere mA ASS'Y BOARD | dan Nete Red MF, SOV, DISC AS SHOWN’ Sonor sete mea / VOLUME MOD www)

NOTES: UNLESS OTHERWISE SPECIFIED

Page 78

PROPRIETARY

THIS DOCUMENT [5 THE PROPERTY

OF CINEMATRONICS INC. AND IS

MOT TO BE REPRODUCED OR

DISTRIBUTED WITHOUT WRITTEN

CONNECTOR [FROM [ TO [ COLOR [AWG [PIN [LENGTA] REMARKS P4-1 SPEAKER BRN 272 M 45.0 A MOLEX P/N PG -2 SPEAKER WHT 22 MM 45.0 A 03-09-2038 py 5 NoT USED

41-10059-Dt ZAXCINEMATRONICS PART NO.

GREAK ALL SHARP

Z\ WIRES TERMINATE AT SPEAKER END WITH — | S2e8 85 Selma

WITH FEMALE. GUICL DISCONNECTS, CINEMATRONICS PN 35-IDGI7-O}

NOTES: 200¥ I2Oy ONIKTG TT Hoo 4] Im 5 nS a OS RN SD A DO DOS DS OO

Page 79

4626v1, rood, wok 128" / 1B lobue-dt PmCieurt Pee Mert ee) PRL ,U-loBSi-o1 TPE fom, Fer llts-01 (2)

Wear Yestt Gen, — Ao-mu-ol (2) AuiGul, wood Woes 48a". 28-loSuu-ol (4)

secre BoB connie PL Bare, euAe | wast Reoeat ies wor, caer ur i, Sonos ton cimtaus YORI, dtrlonencs May VIMEZ, Aut) Ub. 1. 2-loseB-Ol MuT, WOE WOId-24. 2 toeee-ot

Cibvket vita he A B-1427-01 { NOTES: WLS OTHERWISE SPECIFIED T-ws2-01 (1)

  • Cotten, PIL dest, pe 7 $8- NuAl-o% GORT, CARRIRUS, B/G" KIM", 25-le862-01 (2) WMAER . FUST . No, lo x Y2, 25-1oBu8 + SP MOT, vinke,, Hi No.10-24, 25-loLO-c (2)

< Pen SOP anodeD Al nNUgd-ol TAPERLER , W-lOBB-0t 2 eRe, SD, No.8 KN, T-ALL (2) Powe AUPRY BAnY, 3B-UTIL-ol Chir) Pow APPLY Ae SE-NN-O? WAANER, FLAT, Wo. le . 2o-ioBUB-al (5) WOT tex ta lo-14, 45-lo8SB-0t (5)

Page 80

LONBM-LS en ere 2a, 19-SSLi “13

@) 10-9960) -4, lea 8 BON” GOON * NOB (@) 10-0950) -ey, Lats wus * aaa HL

Page 81

PROPRIETARY [Rev] cesceprion Toate | arepoven | ‘THIS DOCUMENT IS THE PROPERTY [Alogi 2 eme®or [4-s-aly ZH

OF CINEMATRONICS INC. AND 18.

NOT TO BE REPRODUCED OR

O:STRISUTED WITHOUT WRITTEN

AUTHORIZATION OF COSEMATROWCS BE-llG9B-01

Powe?

: - FAPPLY Neotel 4B-11134-02 - . Ba-HITIw-ol BB-NTG-02 \ = as a coe A &

NOTES: UNLESS OTHERWISE SPECIFIED

Page 82

357-11192 -02 SWITGH W/MTe. B7- 0373-08

  • REF. DES. SHOWN FOR REFERANCE ONLY AND DO NOT AFPEAC ON PART. AS BALEND OF JOVSTICK UUST BE REMOVED

BEFORE PLICEVENT. APPLY LOCKTITE ON

THEEAD END AND REPLACE BALL... LX commattoucs Paar no. j] | sores wasss oncnmse specimen

  • BOLT CARRIAGE (BLK OX)G4) Siaioce 2§-10909-O8

WASHER FLAT (4)

LEKAN 22-1744 -O

=-01 ASSY PLAVIEI? 0 eS (ees CONTEOL, PANE 8)

Page 83

BUTTON ASYY SHORT (REDD 37-11192 -02 . SWiTa W/ MTS. 37-373 -a!

  • REF. DES. SHOWN FOR REFERANCE ONLY AND DONUT APPEAR ON PAT. AX BALEND OF JOYSTICK WUST BE REMOVED SEFDRE PUCEMENT, APPLN LCCETITE ON Z\ ontmattoucs Part no.

NOTES. WOES OTHERWISE SPECIRED

82-30 [Isr 98-3 THH/St-3 Te Ste: Tsi$3-3 [TH 54-3 Tot sa-3 | PBQ-1 C2 tf CT OC. te of hm UT

BOLT CARRIAGE (BLK 0X24) Saris

WASHER FLAT (4)

#10 -24 25-10568- 01 10-24 25-10558-O1 -02 ASSY

PLAVIER 2

s17/82-3 3. ~ 4.

  • 4.
Page 84

PROPRIETARY

THIS DOCUMENT IS THE PROPERTY

OF CINEMATRONICS INC. AND 13

MOT TO SE REPRODUCED OR

DISTRIBUTED WITHOUT WRITTEN

AUTWORIZATION OF CIXEMATROWCS

imc, [counectoe | From [To [coroe Jawalem [rewatu [eemazue | Pl4-9 ORANGE 22 M 28.0 nm-8 BLUE F P3 m-7 BROWN |

A4-G G2 epee conn. pas Yeuow |

MOLEX PH , pib-4 OLet . PIs-| BLACK any No.1

ove Pi PB-2 Waite Al- loBLo-ol PI3-% a@eeen 'S cig. MALE B3-4 VIOLET PS YELLOW Pa-6 @@ey PIB-7 BeowN 3-8 ive A3-9 omilae

PiS PLANER No.|

MOLEX PIN

03-09-1093 of Ea@uIV. : ove PIN A= (0049-01 9 ce. MALE Pld PLINER No.7 'Movex FIN ' 03-09-1093 oR EQUIV. , Ove PIN j Al- 10W49-ol é ; Vat Mae ita owe THLE Wike LIST= contzoL PL Wremcowd. [A

TOLERANCE JOO NOT SCALE OWS] © OC KTAIL mm 24:

Page 85

Mowitile PATE Plz Het © Tele As- Itor-ot BB: 1LAs-ot Pout? SuPAY B2-loBd2-do came Gal) Teadefozme? , 87-III1-02 Fou OPA 82-1042 -do bein Rowen fo7) GOAT, CARBIAUE . Slur x V2", 25- losSl-ot (4) But, CARMIAGE. Blur ¥ Mes %e- = 4 Wasuer, PLAT. Wo.10 ¢ 1/7", 25-losuB-at (4) WOES Lock, WOO NITEENAL , 26-l0572-01 (4) + Briosy2-a (A) WoT UGK, Wo. lo-24, 2S-losas-ol (4)

Wut Wey, to. lok, 1G-losSB-ot (4)

Page 86

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.