CATHODE RAY TOMES

Cabal

Cabal (World, Joystick) (TAD Corporation, 1988) · Document · 15 pages · 16 sections · original scan

Page 1

>. JE THE DANGER WITN Ye <

SS |e | es \ wea

OWNERS MANUAL — CABAL®

Page 2

VIDEO GAME OPERATOR:

Don’t Get Involved In A Federal Crime. Don't

Buy Or Operate Copy Or Unauthorized Boards In

Your Games.

Every operator who buys or operates a counterfeit or unauthorized

board (imported or domestic) is

contributing to the end of our industry

and commiting a FEDERAL CRIME. New criminal laws have recently been enacted that provide for maxim penalties of $250,000 or five years in prison or both, per offense. EACH GAME {S.A SEPARATE OFFENSE.

If you have any information “hee any nauthortzed panies in the United Siaies, contact your local FBI or, American Armusemest Machine Association 205 The Suund Suite 3 Alexandria, Virginni 22314 (703) 548-8044 All information will-be tread tnecontidence,

Page 3

SAFETY

The following topics should be carefully studied to insure maximum reliability and safety for both serviceman and customer. Shock Hazard: The high voltage present on the monitor may be very dangerous. Extreme caution must be used when working with or around the monitors. Be certain that the grounding strap is attached to the monitor frame. The picture tube in the monitor is also a hazard and should be handled with care, Do not strike, scratch, or subject the tube to more than moderate pressure as it may implode causing serious injury from flying glass. Be certain that the control panel, power supply monitor, and coin door are all properly grounded to the ground wire inside the line cord. Do not remove ground prong off plug end.

PARTS LIST

1 - Plex Marquee 1 - Control Panel Overlay 1 - FCC Cage 1 - Graphic Sheet 2 - Side Graphics 1 - Manual 6 - Buttons 1 - Jamma Cable 1 - Marquee Art 2 - Track Balls & Mounting Hardware 1 - Cabal PCB

FABTEK® 13807 NE 48 Place Bellevue, WA 98005 (206) 882-1093

FOR SERVICE CONTACT:

SUMMIT SERVICE 2274 University Avenue St. Paul, MN 55114 (612) 645-9077

Page 4

CABAL® is protected by federal copyright laws and is the property of Fabtek®. Any unauthorized versions of this game are illegal by federal law. AAMA protected stickers must be attached to the PCB. Please notify Fabtek® of any boards not having the AAMA seal.

IMPORTANT F.C.C. WARNING
WARNING

THIS EQUIPMENT GENERATES AND CAN RADIATE RADIO FREQUENCY ENERGY; IF NOT INSTALLED AND USED IN ACCORDANCE WITH THE INSTRUCTION MANUAL, IT MAY CAUSE INTERFERENCE WITH RADIO COMMUNICATIONS, AS TEMPORARILY PERMITTED BY REGULATION, IT HAS NOT BEEN TESTED FOR COMPLIANCE PURSUANT TO SUBPART J OF PART 15 OF FCC RULES, WHICH ARE DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST SUCH INTERFERENCE. OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA IS LIKELY TO CAUSE INTERFERENCE IN WHICH CASE THE USER, AT HIS OWN EXPENSE, WILL BE REQUIRED TO TAKE WHATEVER MEASURES NECESSARY TO CORRECT THE INTERFERENCE.

DANGER

An isolation transformer must be used with the monitor and power supply.

This game must be equipped with a three wire 110 volt plug for safety. Under no circumstance remove the ground plug.

DANGER

This game is designed with a JAMMA 56 pin connector. This plug is one of the finest operator friendly features in our industry today. What this means to you is that:

  • 1, 2, A, B, 27, 28, e and f are grounded
  • 3,4, C and D are +5 volts
  • 5 and E are -5 volts
  • 6 and F are +12 volts

Also, all video and joystick functions are always in the same place. Once a cabinet is wired for JAMMA, it is easily changed from game to game.

Many older games such as Pac Man®, etc., have the power supply on the board. This will not work!!! Only a JAMMA connector with proper voltage will work. Fabtek® recommends using an 1] amp switching power supply with Cabal®.

Page 5

INSTALLATION OF KIT

To Disassemble:

1, Open back door and remove old board set and power supply, if you are using a new switching power supply.

  • Remove marquee glass and monitor glass.
  • Remove control panel and set aside.
  • Remove old wire harness, leaving 110 volt wiring intact. Also, leave the grounding straps to the monitor, coin door, control panel, and power supply intact.

Installation:

  • Mount the board set on the side panel of the cabinet as close to the middle of the game as possible (approximately 10-12” off bottom).
NOTE: Do not mount board directly below control or any vents or cracks so that liquids may seep on to the board. Do not forget about coins that may drop on to the board. Also, mount the board with edge connector facing up.
  • Mount the power supply on the bottom of the cabinet with connectors facing the rear of the cabinet. An optional mounting might be on the side panel just below the board set, connector to rear.
  • If the game does not have an isolation transformer, you must protect your customers and your game. Install one between the 110 volt line and your monitor/power supply.
  • Place the provided JAMMA wiring harness on the board. Connect the +5, +12, -5, and ground wires to the corresponding lugs on the power supply, connecting all the wires. If you don't, you will probably burn the board connector.
  • Runa wire from -5 volts to the coin door lights. Run a wire from +12 volts to the coin counters. This completes the power requirements.
  • Connect the Audio (+) and Audio (-) to the speaker.
  • Connect the video red, green, blue, ground, and sync to the corresponding wires on the monitor. If the monitor is not a negative composite sync, see sync modifications chart.
  • Cut the marquee to size. Replace the marquee lamp, if needed. Install the marquee panel.
  • Connect the coin 1 and coin 2 wires to the coin switches. Connect the coin counter 1 and coin counter 2 wires to the coin counters.
NOTE: If you only have one coin counter, see coin counter diagram. It will not matter if the coin counters are only rated at 6 volts, as the pulse is not long enough to bum out the counter.
Page 6
  • Mounting the trackballs in your new Cabal® is as easy as 1, 2, 3. First you should choose a

1. horizontal game cabinet. Next, the control panel must have adequate room for the two trackballs and buttons. With the 24” chassis punch, you will find it takes no more effort to mount a trackball than a joystick.

The trackball is wired so the wire coming out of the ball is at 7 o’clock. The black wire is ground, and the red wire is +5 volts. The X-axis (Xa and Xb) is the horizontal axis, and the Y-axis (Ya and Yb) is the vertical axis. If the trackball is rotated 90 degrees, the X and Y pairs of wires can be exchanged. If the cursor tracks left-to-right when moving the ball left, exchange Xa and Xb for that trackball. The end result is doing exactly what you would do if two wires were backwards on a joystick.

The recommended layout is spacing each trackball 1/3 of the way in from each side. If there is room the trackballs should be on the lower portion of the control panel. The shoot and grenade buttons are to be mounted in pairs on the side of the trackballs. If your player base demands it and you have the room, you may add two optional buttons for each player so each trackball has four buttons. The player starts can either be on top or on the left side. When laying out any control panel, place your hand on the panel as if you were playing the game so it feels comfortable. As an example; Don't place the buttons 3”s apart.

Continue as following:

Drill a guide hole for the 2'4" chassis punch. Make the 214” hole using the chassis punch. (Greenlee chassis punch #5004059 214”) Make necessary button holes. Install panel overlay. Mount Lexan (MR-5) over panel overlay as necessary and bevel edges. Using hole saw, make holes in Lexan as necessary. Mount assembly as necessary. When wiring switch common, make a closed loop to all buttons with common feeding player start 2. PND wo

Power up the game. Look over your installation for errors, and then apply power, listening for unusual sounds. Check for smoke or sparks. If everything is okay, wire tie all wires to form a nice, neat wiring harness. Clean the cabinet inside and out. Measure the +5 volts on the board, at the furthest point from the edge connector and adjust 5 volts to 5.05 volts. Use a tinted plex over the monitor if there are burns in the screen. We suggest bronze or grey tinted plex. Touch up the cabinet with fresh paint, and then repair all cabinet dents or chips, using an auto body product called Duraglass. This is similar to bondo. You can consult your local auto body shop or auto parts supplier for this product, as well as advice on how to use it.

NOTE: If you are going to use plexiglass over the control panel, we suggest that you use a good %” polycarbonate with a scratch resistant coating. We recommend GENERAL ELECTRIC LEXAN MR5 with margard or TUFFAK CM-2. These do not crack or break with abuse.

; © TRACKBALL 2 TRACKBALL 1 © oe e e e

FIRE FIRE

Page 7

CABAL® by Fabtek®

Fabtek © is dedicated to being the most operator-oriented company in the game industry. In respect to you, the operator, this means several things, such as:

  • Having the clearest instructions possible so that you can minimize the time it takes to put the game together;
  • Providing useful information to help you produce the best-looking and highest earning game from your Fabtek® Kit;
  • Informing you of the proper setting for your game in both street and arcade locations. This is a first for the game industry; we realize that the differentiation between these two types of locations is important, and we want to help you prepare your game so that you can maximize your profits accordingly.
  • Continuing to keep the operator informed by publishing all service bulletins in the Star Tech Journal and in all other Trade Magazines.

| To accomplish all of this, Fabtek® uses more operator input. Our games are made to be operated by operators such as yourself; you need all the information you can get today in order to make a maximum profit.

We would like to thank you for purchasing your new Fabtek® game. We are sure that the Fabtek® way will bring you back to us, game after game. Happy remunerations!

; CABAL® “TRACK BALL ADAPTOR”

‘ CABAL® track ball adaptor (to be connected between track ball and edge connector). Track . balls which are made in Japan specification is OPEN EMITTER. In order to have the track balls function properly with the track balls not made in Japan, you must use the adaptor below to make the specification OPEN COLLECTOR.

Edge Connector Side

LIZA heey fit = =z

s He x 16 ) LS245 20.4 . é 2 4 a . «

oikA TAXA TA ésy) = VCCON u B (normally black wire) (ground) &

z ors (normally red wire) (+5V)

“XR YB XB vB

Track Ball Side YA YB

Page 8

MONITORS

Cabal® is designed to be operated with a horizontal raster scan monitor with negative sync (RGB). This means Cabal® will not work with any X-Y (Tempest, Space Dual, Star Trec), etc. An isolation transformer must be used in conjunction with the monitor. This is for your safety. The monitor also utilizes extremely high voltages. The monitor may also retain a charge for an extended period of time. Safety goggles must be worn while removing or replacing the monitor.

It is highly recommended that the monitor is verified good before the new Cabal® kit is installed in your new and or rebuilt cabinet.

Cabal®, Dynamo® style

Fabtek® is concerned that your Fabtek® game will out earn the competition by 20 percent. The cabinet your kit is installed in will have a major effect on how much money it earns. Installing the game in a used cabinet that has already been kitted several times may not be the best way to maximize profits.

In arcade locations it is recommended installing Cabal® in the Dynamo 25 inch cabinet: We feel the game will earn 20 percent more money because of the 25 inch monitor and the creative styling of the Dynamo cabinet. With the JAMMA connector the game can be powered in about five minutes with only the control panel to be wired.

Dynamo® also has a 19 inch game cabinet for smaller street locations.

WICO COMMERCIAL TRACK BALL

TOP CENTER NOTE: Due to various manufacturers’ electronic characteristics, you may find that your Trackball Unit, though properly orientated, is visually reversed on the video screen. To correct this problem, the following change(s) must be made to harness wires:

  • To switch HORIZONTAL direction ( -* ), exchange the BLUE & VIOLET wires.
  • To switch VERTICAL direction (f ), exchange the YELLOW & GREEN wires.
Page 9

Star Tech Tips

We are grateful to Star Tech Journal m for allowing us to publish the following excerpts from their journal. Monitor Sync Ifyour monitor does not have dual polarity positions for sync, you may use one of the following methods to get your game going. CURE I: Install a simple one I.C. Circuit on your logic board. This I.C. may be “piggy backed” on to another 7404 series chip for power by bending up all but the two power pins so that they are parallel to the top surface of the new I.C. and then connecting the power pins only to the existing chip. (See Fig. 1) Next connect the sync wires as shown in Fig. 2. (Note: Figure 2 shows a hookup for either composite or separate syncs.) HORIZONTAL SYNC INPUT FROM PC 8 Suc SVOC [PIN 14) {OR COMPOSITE SYNC INPUT) SOLDER TO HORIZONTAL SYNC OUTPUT TO MONITOR EXISTING CHIP {OR COMPOSITE SYNC OUTPUT} VERTICAL SYNC INPUT FROM PCB

VERTICAL SYNC OUTPUT TO MONITOR

NEW 74.5 04

FIG. 2

CURE 2: Used for Wells-Gardner Video-Sync boards with positive sync connections only. (Vertical mount board 85x140B.

Cut the traces on the solder side of the board between input pins 5 & 6 to the unbanded (anode) ends of diodes X201 & X202. Add MPSAS56 transistor as follows: Collector to anode leads of diodes X20! & X202. Base to pins 5 & 6 of the video input connector. Emitter to cathode (banded] lead of zener diode ZD20). . Insert a IN4148 diode - cathode to the emitter of the MPSA56 and anode to the base. (See Fig. 3) REDT GREEN 2 BLUE 3 GND4 FIG 3 VERT 5S HORIZ 6 (MPSAS6 0000

Page 10
  • Horizontal Tearing CAUSE: The negative sync signal of most logic sets are slightly different than the GO7-CBO menitor negative sync inputs. The result of this mismatch is a horizontal “wave” or “curl”. éE 1: On the monitor deflection board, replace C 303 with a 10uf 25V radial lead capacitor with the ive lead towards the collector of X305. (CAUTION: he sure to check this step as the original cap is net polarized.) Then repiace C501 with the cap removed from the C 3023 location.

CURE 2: Connect IN4148 fast-switching diodes across both the positive and negative SYNC inputs to the monitor. (See Fig. 4) NOTE: Both diodes must be installed or you will not have vertical stability,

IN4I48 : NEC SYNC INPUT

-—shar

rhe -v- ©: GND

CeSeoe
Wea3?1

GND = BLUF GREFN RED = - > eK vO O_O OF 7 3 2

INR

CURE 3° Join negative sync inputs J2 and J3 together with a jumper. Locate \W/102 and instal! ajumper from W102 to either J2 or J3

CURF 3. For Wells-Gardner K4600 series monitors ®ophce C256 (4 Juf 25V) on the Horizontal vertical board (vertically mounted board nearest the flyback transformer) and center the horizontal hold pot. Turn L351 for the best horizontal Stability and fine tune with the horizontal’width pot.

COIN COUNTER DIAGRAM

If only one coin counter is to be used install two diodes in the following manner:

in 4001 +12 volts coin counter 1

in 4001 ! : :

i¥’coin counter

if diode in meter is not present install one coin counter 2

Page 11

CABAL

SULDER SIDE COMFONENT SIDE

GRGUNDGROUNDBLACK
“BLACKGROUND=2GROUNDBLACE.
;RED+8 VOLTS:+5 VOLTSRED
RED: | +5 ‘VOLTS+5 VOLTSRED
YELLOW/ GREEN-S VOLTS5-5 VOLTSYELLOW/ GREEN
ORANGE/ BLACK +12 VOLTS7 "+12 VOLTSORANGE/ BLACK

c IN COUNTER 2

SPEAKER — OLN COUNTER 1] WHITE/BLACK

SPEAKER + VIOLET/ RED

M

VIDEO GREENN:VIDEO RED

SYNC - s VIDEO BLUE EB

R VIDEO GROUND

S 7

COIN SWITCH 2TCOIN SWITCH 1 GRAY/ BLUE
2P CONTROL XAE 1F CONTROLWHITE/ GREEN

START SWITCH 2 START SWITCH en

* CONTROL XBCONTROLWHITE/ BLUE
CONTROL YA20CONTROLBLUE/ GREEN
CONTROL YEe CONTROLBROWN/ YELLOW

RED/ GRAY SF FUSH 1

RED/ WHITE 2F PUSH 2 1f FUSH YELLOW/ BLACK

1F FUSH 2 BLUE/ BLACK

BLACE GROUND

GROUND|BLACK,
BLACK.GROUND ~ |1GROUNDBLACK

WKELANE SPACES ARE NOT USED. X AXISSLEFT, RIGHT (HORIZONTAL) Y AXIS=UF, DOWN (VERTICAL)

Page 12

Button AB exchange TV tnvere

track ball

option

@ of lives at stare

increase # of lives

diff€iouley

attract mode agund lgoin 3 pla coin 6

Page 13

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 14

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 15

SPEAKER

RGB MONITOR

NEGATIVE SYNC

HORIZONTAL

SOLATION

TRANSFORMER

OY ili

PRINTED CONTROL PANEL CIRCUIT BOARD