CATHODE RAY TOMES

Street Fighter II Alpha

Street Fighter Alpha (Capcom) · Manual · 26 pages · 20 sections · original scan

Page 1

OPERATORS MANUAL

JN WARNING

This game is for use in the United States of America and Canada. Sales, export or operation outside of these countries may be construed as copyright and trademark infringements and is strictly prohibited. Violators are subject to severe penalties and will be prosecuted to the full extent of the law.

ICARCOM\ COIN-OP, INC. 3311 N. Kennicott Road Arlington Heights, Illinois 60004 Phone: (708) 797-6100 PM00125-KIT Fax: (708) 797-6306 063095

Page 2

@AP@OH° coin-op, Inc. Street Fighter™: Alpha

THANK YOU FOR PURCHASING Street Fighter™: Alpha VIDEO KIT. WE INVITE YOU TO USE THE FOLLOWING MAILING ADDRESS, TELEPHONE OR FAX NUMBER FOR PARTS OR SERVICE INFORMATION CONCERNING THIS GAME:

CAPCOM® COIN-OP, INC. ATTN: FIELD SERVICE - VIDEO PRODUCTS 3311 N. KENNICOTT ROAD ARLINGTON HEIGHTS, ILLINOIS 60004 PHONE: (708) 797-6100 FAX: (708) 797-6306

THE SERIAL NUMBERS OF YOUR KIT ARE LOCATED ON THE GAME CARTRIDGES AS SHOWN BELOW. PLEASE HAVE THESE SERIAL NUMBERS AVAILABLE WHEN CONTACTING US FOR SERVICE INFORMATION.

“B" CARTRIDGE SERIAL NUMBER

"A" CARTRIDGE SERIAL NUMBER (BOTTOM OF CASE) 'v300900

DEPENDING ON THE TYPE OF KIT YOU PURCHASED, PLEASE RECORD THE SERIAL NUMBERS HERE:

“FULL” KIT A-CARTRIDGE SERIAL # B-CARTRIDGE SERIAL # AAMA SERIAL #

“A” KIT A-CARTRIDGE SERIAL #

“B” KIT B-CARTRIDGE SERIAL # AAMA SERIAL #

‘Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN- OP, INC.

Page 3

@APEOMIcon-op, INC. Street Fighter™: Alpha

Warranty Information

Kit Inspection

Kit Installation “FULL” Kit Installation Preparation Installation Marquee Control Panel Wiring Test Bracket Game Cartridges “A” Kit Installation Preparation and Installation “B” Kit Installation Preparation and Installation

Test Mode Test Menu Accessing the Menu How to Select an Item Closing the Menu Menu Item Descriptions Configuration Menus Accessing the Menus Changing the Settings Saving and Closing the Menu Menu Option Settings Menu Item Descriptions

JAMMA Connections Auxiliary Cable Connections

Template : Control Panel Drill Hole(s) TABLE OF CONTENTS

Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 4

@NPEONM coin-op, INC. Street Fighter™: Alpha

LIMITED PRODUCT WARRANTY (APPLIES TO DOMESTIC SALES ONLY)

CAPCOM® COIN-OP, INC. (Seller), warrants only to the initial purchaser of its products, that the items listed below are free from defects in material and workmanship under normal use and service for the warranty periods specified:

A. CPS II System Cartridges One (1) Year B. Electronic and Mechanical Components: (90) days

No other part of Seller's products are warranted.

Warranty periods are effective from the initial date of shipment from seller to its authorized

Seller's sole liability shall be, at its option, to repair or replace products which are returned to Seller during the warranty periods specified, provided:

A. Seller is notified promptly upon discovery by buyer that stated products are defective.

B. Such products are properly packaged and then returned, prepaid to Seller's designated

This warranty does not apply to any parts damaged during shipment or handling, or due to improper installation or usage, or alteration. In no event shall Seller be liable for any anticipated profits, loss of profits, loss of use, incidental or consequential damages or any other losses incurred by the customer in connection with the purchase of a CAPCOM® COIN-OP, INC. product.

WARRANTY DISCLAIMER

EXCEPT AS SPECIFICALLY PROVIDED IN A WRITTEN CONTRACT BETWEEN SELLER AND PURCHASER, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

IMPORTANT NOTICE

THIS SHIPMENT HAS BEEN CAREFULLY INSPECTED AND PROPERLY PACKAGED BEFORE LEAVING THE FACTORY. WE CANNOT ASSUME RESPONSIBILITY FOR BREAKAGE THAT MAY OCCUR DURING TRANSPORTATION OF THE GAME. IF THIS GAME IS DAMAGED UPON RECEIPT FROM THE CARRIER, IMMEDIATELY NOTIFY THE CARRIER AND FILE A DAMAGE REPORT.

Page i Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 5

@APCOM coin-op, INC. Street Fighter™: Alpha

KIT INSPECTION

There are three kits available for conversion to Street Fighter™: Alpha :

  • SFA1000 (“FULL” kit) contains the complete game cartridges, all necessary graphics, and replacement joysticks and button switches. The “FULL” kit is intended for conversion of most JAMMAcompatible, horizontal screen cabinets.
  • SFA1000A (“A” kit) is compatible only with current CAPCOM® System II games. It is similar to the “FULL” kit but does not include both cartridges (only the A-cartridge is supplied). For operators who have previously converted a cabinet with a “B” kit, the purchase of an “A” kit will provide all the additional components necessary for “FULL” cabinet conversion (“A” + “B” = “FULL”)
  • SFA1000B (“B” kit) contains the game software cartridge (B-cartridge) and must also be installed to a current CAPCOM® System II game. It includes all the necessary game graphics for a cabinet conversion (marquee, control panel overlay, monitor card, etc.).

Check that all parts have been shipped with your kit. If any parts are missing, contact your distributor immediately.

KIT PARTS LIST

PART NO. DESCRIPTION A-00448 CPS II System Cartridges (A/B ) ZZ1400A CPS II System Cartridge (A ) A-00452 CPS II System Cartridge ( B ) GE1200 Monitor Card AW00155 Marquee 06-0074 Overlay, Control Panel AW00151 Decal, Joystick & Button Switches AW00147 Decal, “CAPCOM® COIN-OP, INC.” AW00156-01 Decal - Right, Instruction AW00156-02 Decal - Left, Instruction PM00125-KIT_| Manual, Operators 03-0052 Cable, Auxiliary GE2030 Joystick 16-0130 Switch, 1-Player Start Button (White) 16-0131 Switch, 2-Player Start Button (White) 16-0133 Switch, Punch/Kick Button (Red) 16-0134 Switch, Punch/Kick Button (Blue) 16-0136 Switch, Punch/Kick Button (Green) 03-0050 Bracket, Volume/Test 13-0066 Bracket, A-Cartridge Mounting $C00104-05 Screw, Wood 13-0141 Clamp, Case a}ej<j<}<}<)<j<e]<] v v v v v v v v v v v v v v v v v v a}ej<}<iej<i<}<)et<j<j <i

Proprietary and confidential information, not to be disclosed oF copied without the express permission of CAPCOM® COIN-OP, INC. Page 1

Page 6

GAP@OM coIN-oP, INC. Street Fighter™: Alpha

CAUTION

Please read the following instructions to keep the PC board in good condition:

Do not block the ventilation slots.

Do not drop or bump the board.

Do not spill any liquids on the case.

Do not disassemble the case.

ATTENTION The product that you have purchased contains a rechargeable battery. The battery is recyclable. At the end of its useful life, under various state and local laws, it may be illegal to dispose of this battery into the municipal waste system. Check with your local solid waste official for details in your area for recycling options or proper disposal.

DISASSEMBLING THE CASE OR REMOVING THE STICKER MAY CAUSE THE TERMINATION OF YOUR REPAIR WARRANTY.

Page 2 [[Propriciary and confidential information, not tobe disclosed or copied without the expres permisdon of CAPCOM® COIN-OF, ING.

Page 7

@APEEM” coIN-oP, INC. Street Fighter™: Alpha

"FULL" KIT INSTALLATION

WARNING:

MAKE SURE ELECTRICAL POWER TO THE GAME IS OFF BEFORE STARTING THE KIT INSTALLATION.

PREPARATION

  • Disconnect and remove the old printed circuit board(s) from the cabinet.
  • Remove or open the control panel, and disconnect and remove the buttons and joystick(s) from the control panel.
  • Remove any covering from the control panel overlay, and then remove the control panel overlay.
  • Place the Drill Hole template over the control panel to determine where any new holes should go. Center punch any needed new holes on the control panel.
  • Cut out the new holes using a 1-3/16" hole saw.
  • If there is an additional control panel cover (such as plastic or lexan) that will be utilized, cut any additional holes using the same template.
  • Plug up unused holes with a wood dowel (1-1/8" diameter) and sand any rough edges.

INSTALLATION

Marquee Installation

  • Remove the marquee glass, old marquee overlay, and the old cabinet graphics.
  • Install the new marquee and replace the glass.

Control Panel Overlay Installation (See Figure 1)

  • The control panel overlay in the kit is oversized to accommodate most control panel sizes. Center the overlay on the control panel, leaving some excess material at the edges.
  • Remove the protective backing from the overlay and press it down on the control panel, keeping it properly aligned. Press itdown firmly, smooth out any bubbles, and press it over the edges.
  • Trim any excess from the overlay. Place the drill hole template on top of the overlay, aligning it with the joystick holes. Pierce through the overlay at each control panel hole. Then, cut away overlay material covering the joystick and button holes. Remove the template and clean off the overlay.
  • Peel off the backings of the 6-button and joystick decals, align over the control panel holes, and press in place on the overlay (refer to the drill hole template for proper placement). Using a knife, trim material from the center hole of the joystick decal.
  • Install the control panel cover (if required).

FIGURE1 Overlay Installation

Reassembly of Components

  • Install all buttons and retaining rings on the control panel as shown in Figure 2. Install two RED buttons to the immediate right of each joystick, install two GREEN buttons to the right of the red ones, and install two BLUE buttons to the right of the green ones.

Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC. Page 3

Page 8

@APEOM” COIN-OP, INC.

Control Panel RED GREEN BLUE RED GREEN BLUE

Buttons

ae ee

FIGURE2 Control Panel Buttons and Switches

  • Notice that there are two white buttons. (See Figure 3.) Install the PLAYER ONE button on the top left-hand side of the control panel, and the PLAYER TWO button on the top right-hand side of the control panel. The WHITE buttons are START buttons.

1 Player 2 Player

NZ ¥7

FIGURE3 Function and Start Buttons

  • Install the switches on the buttons as shown in Figure 2. Orient the switches so that when a button is pressed, the red contact on the switch is depressed.
  • Install the joysticks on the control panel as shown in Figure 4.

Wiring

NOTE: All switch wires used in this game must be wired to the normally-open connection on the switches. Each switch requires a ground wire on the common

Page 4 Street Fighter™: Alpha

FIGURE4 Joystick Installation connector and the appropriate control or switch wire on the normally-open connector of the switch.

  • Reconnect the existing JAMMA connectors to the control panel according to the chart of Figure 5.
  • Connect the Player 1 and Player 2 Kick buttons to the auxiliary cable harness connectors shown in Figure 6. Make the connections according to the chart of Figure 7.

TO GAME CASE CONNECTOR

TO PUSH-BUTTON SWITCHES

TO VOLUME & TEST SWITCHES

FIGURE6 Auxiliary Cable Harness

Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 9

CAPE coIN-oP, INC.

JAMMA CONNECTOR REF. *WIRE COLOR WHITE/BLACK CONNECTS TO PLAYER 1 Street Fighter™: Alpha™

COMPONENT JOYSTICK FUNCTION

WHITE/BROWN PLAYER 1 JOYSTICK WHITE/RED PLAYER 1 JOYSTICK WHITE/ORANGE PLAYER 1 JOYSTICK WHITE/YELLOW PLAYER 1 PUNCH BUTTON WHITE/GREEN PLAYER 1 PUNCH BUTTON WHITE/BLUE PLAYER 1 PUNCH BUTTON

VIOLET/BLACK PLAYER 2 JOYSTICK VIOLET/BROWN PLAYER 2 JOYSTICK VIOLET/RED PLAYER 2 JOYSTICK VIOLET/ORANGE PLAYER 2 JOYSTICK VIOLET/YELLOW PLAYER 2 PUNCH BUTTON VIOLET/GREEN PLAYER 2 PUNCH BUTTON VIOLET/BLUE PLAYER 2 PUNCH BUTTON

Figure 5: JAMMA Wiring Connections

  • Wire Color Note: Wire colors shown are according to the AAMA -AMOA Standard for wire color assignments; your harness may contain different colors than shown above.

AUXILIARY CABLE CONNECTOR REF. WIRE COLOR CONNECTS TO PLAYER 1 KICK BUTTON

COMPONENT FUNCTION

COMMON PLAYER 1 KICK BUTTON SHORT PLAYER 1 KICK BUTTON FORWARD PLAYER 1 KICK BUTTON ROUNDHOUSE

PLAYER 2 KICK BUTTON COMMON GRAY/YELLOW PLAYER 2 KICK BUTTON SHORT PINK/YELLLOW PLAYER 2 KICK BUTTON FORWARD PURPLE/YELLOW PLAYER 2 KICK BUTTON ROUNDHOUSE

GRAY/YELLOW TEST BRACKET VOLUME SWITCH UP

PINK/YELLOW TEST BRACKET VOLUME SWITCH DOWN

‘Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN.OP, INC. BLACK/WHITE TEST BRACKET VOLUME SWITCH

Figure 7: Auxiliary Cable Wiring Connections COMMON

Page 5

Page 10

@APEOM coin-op, Inc. Street Fighter™: Alpha

  • An optional Test/Volume bracket (see Figure 8) is included in this kit. Your cabinet may already contain this bracket. If you decide to install, the bracket should be mounted inside the coin door and on top of the cash box for easy access.
NOTE: The A-cartridge also contains the same Test and Volume functions found on the test bracket.

‘300500 Figure 8: Test Bracket

Wiring of the Test Bracket requires connections to both the main JAMMA harness as well as the auxiliary cable harness (refer to Figure 9).

LEAD WIRE CONNECTS COLOR TO VVOLUME-UP | AUX. CABLE *29’(GRAY/ YELLOW) COMMON | AUX. CABLE “31’(BLACK/ WHITE) VOLUME- DOWN AUX. CABLE “30°(PINK/ YELLOW) AUX. CABLE *31’(BLACK/ WHITE) COMMON

TEST JAMMA ‘15’

GROUND _ | JAMMA ‘A’ or “B’ or ‘e’ or ‘f? or ‘1’ or ‘2’ or ‘27’ or ‘28’ Figure 9: Test Bracket Wiring Chart GAME CARTRIDGE INSTALLATION

  • Install the four (4) mounting brackets to the underside of the “A” cartridge as shown in Figure 10.

© QU

ESS A

a S

Za

Figure 10: Mounting Bracket Installation

  • Using the supplied wood screws, fasten the game cartridge case to the control panel shelf, as shown in Figure 11.

Figure 11: Case Mounting

  • Connect the JAMMA harness connector and the auxiliary cable connector to the “A’ cartridge. If your cabinet is equipped with Q- SOUND, also attach the audio cables.

Page 6 Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 11

@ANP@OMcoIn-op, Inc.

WARNING

Improper installation of the JAMMA harness connector to the game cartridge will cause damage to the enclosed PCB.

  • Power-up the game and set all operator adjustable options by pressing the TEST switch. Follow the instructions under the Test Mode section of this manual.

“A” KIT INSTALLATION

  • To install the control panel parts, you must follow the “FULL” Kit Preparation and Installation Procedure, steps 15 through 22.
  • To mate the existing “B” cartridge with the “A” cartridge, align the “B” cartridge over the “A” cartridge and push down firmly. Install the case clamps as shown in Figure 12.

"A" Cartridge

Figure 12 : Case Clamp Installation Street Fighter™: Alpha

  • Continue to follow the “FULL” kit Preparation and Installation Procedure, steps 24 through 26.
  • Installation of the “A” kit is now complete.
WARNING

DISASSEMBLY OF EITHER GAME CARTRIDGE WILL VOID YOUR WARRANTY.

“B” KIT INSTALLATION

  • To install the cabinet graphics, you must follow the “FULL” Kit Preparation and Installation Procedure, steps 3 through 20.
  • To remove the existing “A” cartridge from the “B” cartridge, pull the old case clamps apart and discard (see Figure 12). Carefully remove the old “B” cartridge and install the new “B’ cartridge. Install the new case clamps.
  • Power-up the game and set all operator adjustable options by pressing the TEST switch. Follow the instructions under the Test Mode section of this manual.

‘Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC. Page 7

Page 12

CAPCOM "coin-op, Inc. Street Fighter™: Alpha

NOTES

Page 8 Proprictiary and confidential information, not tobe disclosed or copied without the express permision of CAPCOM® COIN-OF, INC.

Page 13

@ANP]ONCoIN-OP, INC. Street Fighter™: Alpha

TEST MENU

The test menu allows you to test the functions and configure the game. These items include input devices such as joysticks, buttons and coin mechs, output devices such as monitor, speakers and meters. Through the Test Menu you can also access the Configuration Menu, where you can change the settings of the game.

  • ACCESSING THE TEST MENU

. For a CAPCOM cabinet, or a cabinet equiped with a test switch: Make sure the game is on and push the test switch. The screen shown below will appear. . For a cabinet without a test switch: Push the test switch on the side of the blue plastic game casing. (Refer to the inside back cover of the manual.)

INPUT

OUTPUT

SOUND & VOICE

COLOR

DOT CROSS HATCH

GAME DATA

CONFIGURATION

MEMORY CHECK

EXIT 1.

2.

3.

4.

5.

6.

7.

8.

9.

  • HOW TO SELECT AN ITEM

. Use the Player 1 Joystick to Move the arrow in front of the desired item and press the Player 1 JAB PUNCH button. ° To return to the test menu, push the Player 1 Start and Player 2 Start Buttons simultaneously. The test menu automatically appears: . After you exit the “7. “CONFIGURATION MENU”. . After the memory is tested from the menu, “8. MEMORY CHECK”.

  • CLOSING THE TEST MENU

To close the Test Menu, highlight “9. EXIT” and push the Player 1 JAB PUNCH button.

[Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OF, INC. Page 9

Page 14

@APEOM" coin-op, Inc. Street Fighter™: Alpha

  • TEST MENU ITEM DESCRIPTIONS

INPUT Used to test all the input switches, such as joysticks and buttons. The "0" changes to a "1" as the button is pushed or joystick is moved. Check connections and switches in case the "0" doesnt change to a "1" when depressed or moved.

OUTPUT Used to test the coin meter and the coin lock

SOUND & VOICE Select a code of SOUND or VOICE with the Player 1 Joystick. Push the Player 1 JAB PUNCH button to hear the sound of the selected code.

COLOR Shows color bars of red, green, blue and white. Adjust RGB and brightness to obtain the optimum color balance and solid black background.

DOT CROSS HATCH Used to test the screen size, focus and distortion.

GAME DATA Counter information and the average of the game played time will be displayed.

CONFIGURATION Used to change the game play settings. Refer to the CONFIGURATION MENU section.

MEMORY CHECK Used to test memory.

"OK" appears when each block of memory passes test

"ERROR" appears in case of malfunction. If "ERROR" appears, repeat

the memory test. Contact your distributor if "ERROR" still appears.

Select this item and push the Player 1 JAB PUNCH button to return to game play mode.

Page 10 Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 15

CAPCOM’ COIN-oP, INC. Street Fighter™: Alpha ees

CONFIGURATION MENUS

The Configuration Menu is used to change various game settings such as level of difficulty, credits, sound configuration, etc. These settings are stored in memory on the PCB rather than DIP switches. To change configuration settings you must enter test mode and then access the Configuration Menu.

The Configuration Menu is divided into 2 sections. In the System Configuration section, you can change system credits, sound, and coin mech configuration. In the Game Configuration section, you can change game play difficulty level and game duration.

  • ACCESSING THE CONFIGURATION MENU

. From the Test Menu, move the arrow to “7. CONFIGURATION” and push the Player 1 JAB PUNCH button. The screen below will be displayed. A description of each option is discussed in the table below.

  • CONFIGURATION MENU

SYSTEM GAME DEFAULT SAVE & EXIT

SELECT = 1P UP OR DOWN

START = 1P SHOT 1

Use this screen to change system configuration such as credits, monitor SYSTEM 7 5 . flip, sound and coin mech configuration.

Use this screen to change difficulty level, damage level, time count speed, a maximum number of rounds and event type.

Use this to return configuration to original settings. To insure that settings DEFAULT are not defaulted by accident the Player 1 JAB PUNCH and Player 1 STRONG PUNCH buttons must be pressed at the same time.

SAVE & EXIT Use this to save new configuration settings and exit to Test Menu.

Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC] Page 11

Page 16

@ANP@EOM COIN-OP, ING. Street Fighter™: Alpha SSS Es eee Eee

To access the System or Game Configuration menus from the screen display, move the arrow with the joystick until it is to the left of the desired menu and press the Player 1 JAB PUNCH button. Below are samples of the System and Game Configuration Menus.

SYSTEM CONFIGURATION MENU

7-1. SYSTEM CONFIGURATION

. COINMODE CONTINUE MONITOR DEMO SOUND |. SOUND MODE . CHUTE TYPE EXIT

SELECT OPTION MODIFY SETTING

GAME CONFIGURATION MENU 2COINS 1 CREDIT

ON NORMAL ON STEREO (QSOUND) 4 CHUTE SINGLE

= 1P UP OR DOWN P LEFT OR RIGHT P SHOT1 OR SHOT2

7-2. GAME CONFIGURATION

. DIFFICULTY

. DAMAGE LEVEL

. TIMER SPEED

. GAME SPEED

. MAX ROUND

. EVENT

. AUTOMATIC

. EXIT

Page 12 HARD 2

Low

NORMAL

TURBO 2

3 ROUND

OFF

‘Proprietary and confidential information, not to be disclosed o copied without the express permission of CAPCO} ‘COIN-OP, INC.

Page 17

CAPCOM’ COIN-OP, INC. Street Fighter™: Alpha

  • CHANGING THE CONFIGURATION SETTINGS

Move the Player 1 Joystick UP or DOWN to highlight the desired option. Once the option is highlighted, move the Joystick LEFT or RIGHT, or press the Player 1 JAB PUNCH button to change the setting. Refer to the 4. Menu Option Settings section for option settings.

  • SAVING SETTINGS AND CLOSING THE MENU

Once the configuration settings are changed in either the System or Game Configuration Menus, move the arrow to the EXIT option in each respective menu and press the Player 1 JAB PUNCH button. This will return you to the Configuration Menu. At the Configuration Menu move the arrow to 4. SAVE & EXIT and press the Player 1 JAB PUNCH button. You will be returned to the Test Menu. A message “SAVING NEW CONFIGURATION IN EEPROM” appears while new settings are being saved. It takes one or two seconds to save the new settings. Do not tum off the power switch while saving is in process. From the Test Menu move the arrow to 9. EXIT and press the Player 1 JAB PUNCH button. This will return you to game mode.

  • MENU OPTION SETTINGS

System Configuration Menu Settings

1. COIN1 COIN1 COIN1. COIN1 COIN
1 CREDIT2 CREDITS3 CREDITS4 CREDITS5 CREDITS
1 COIN1 COIN1 COIN1. COIN2 COINS
6 CREDITS7 CREDITS8 CREDITS9 CREDITS1 CREDIT

COIN

3 COINS4 COINS5 COINS6 COINS7 COINS
1 CREDIT1 CREDIT1 CREDIT1 CREDIT1 CREDIT

8 COINS 9 COINS | 2coINS START

1 CREDITCREDIT|! com continue]FREE PLAY

CONTINUE ON OFF MONITOR FLIP NORMAL

DEMO SOUND ON OFF

SOUND MODE STEREO (Q SOUND) MONAURAL

1 CHUTE SINGLE

CHUTE TYPE 2 CHUTES SINGLE

2 CHUTES MULTI

roprictary and confdeniial information, no tobe disease or copied without the expres permisdoa of CAPCOM® COIN-OP ING] Page 13

Page 18

C/NP@OM” COIN-OP, INC. Street Fighter™: Alpha

Game Configuration Menu Settings

DIFFICULTY NORMAL HARD 1 HARD 2 HARD 3

HARD 4 HARD 5 EXPERT EASY

DAMAGE LEVEL NORMAL HIGH IMAXIMUM LOW

TIMER SPEED NORMAL FAST FASTEST SLOW

+— GAME SPEED NORMAL TURBO 1 | TURBO 2 | FREE SELECT

MAX ROUND 3 ROUNDS | 5 ROUNDS 1 ROUND

EVENT OFF 1 MATCH

AUTOMATIC OFF FREE SELECT

Capcom recommended settings are in bold face. After you change the setting, make sure to select "EXIT" and push the Player 1 JAB PUNCH button. « Choose STEREO (QSOUND) if your cabinet is equipped with the Qsound Speaker System, otherwise select MONAURAL for proper sound effect.

Page 14 Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 19

@APEOM’coIN-oP, INC. Street Fighter™: Alpha

MENU ITEM DESCRIPTIONS

System Configuration Option Descriptions

COIN Sets the charge per play

CONTINUE Sets continuous play. ON: Continuous play is possible OFF: Continuous play is not possible

MONITOR FLIP Flips the screen. If the screen appears upside down, change the setting. FLIP: Upside down NORMAL: Right side up

DEMO SOUND Turns attract sound on or off.

SOUND MODE STEREO or MONAURAL. STEREO: withQSOUND MONAURAL: without QSOUND QSOUND is available with CAPCOM QSOUND cabinets only. For other cabinet, please set to MONAURAL

CHUTE TYPE Sets the number of player(s) and coin chutes. 1 CHUTE SINGLE With this setting, either player can start the game. 2 CHUTES SINGLE Two players use one coin chute and play at the same time. With this setting, the player whose coin was put in first starts the game. 2 CHUTES MULTI Two players use two coin chutes and play separately. With this setting, the game is started from the same side the coin chute was used.

EXIT To save the setting changes and return to the CONFIGURATION MENU, highlight this item and push the PLAYER 1 START button.

[Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, ING] Page 15

Page 20

@ANP@OM coIn-op, INC. Street Fighter™: Alpha

Game Configuration Option Descriptions

DIFFICULTY Sets the game difficulty level. There are eight levels of difficulty from EASY to EXPERT.

DAMAGE LEVEL | Sets the attack damage level. There are four levels of damage from LOW to MAXIMUM. r TIMER SPEED Sets the speed of the countdown for the timer display. There are four speed levels from SLOW to FASTEST. {| GAME SPEED Sets the speed at which the characters fight.

Sets the number of rounds for winning. MAX ROUND 1 ROUND: Winner of a single round wins. 3 ROUNDS: Winner of 2 out of 3 rounds wins. 5 ROUNDS: Winner of 3 out of 5 rounds wins.

Turns on event mode. Useful for Championship Tournaments. OFF Normal setting. Sets the mode to normal operation.

1 MATCH Matches player with 1 credit. However, a win or a loss results in EVENT GAME OVER. CONTINUE is not available.

SUDDEN DEATH The player that takes the initiative wins. One strike settles the fight.

1 MATCH & SUDDEN DEATH Sets to 1 MATCH mode as well as SUDDEN DEATH mode.

AUTOMATIC Allows for an automatic blocking feature for most characters (to be used for beginning players).

EXIT Returns to the Configuration Menu.

Page 16 Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC. |

Page 21

@APECOM coin-op, INC. Street Fighter™: Alpha

NOTES

Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC. Page 17

Page 22

CANR@OMIcoin-op, INC. Street Fighter™: Alpha

JAMMA Connections

COMPONENT SIDE SOLDER SIDE

KEY NIC COIN COUNTER 1 COIN LOCK 2 COIN LOCK 1 *SPEAKER (+) N.C. VIDEO RED VIDEO BLUE SERVICE (FREE CREDIT) VIDEO GND NIC TEST MODE (DIAGNOSTICS) 2 PLAYER - COIN 1 PLAYER - COIN 2 PLAYER - START. 1 PLAYER - START 2 PLAYER - UP 1 PLAYER - UP. 2 PLAYER - DOWN 1 PLAYER - DOWN 2 PLAYER - LEFT 1 PLAYER - LEFT 2 PLAYER - RIGHT 2 PLAYER -JAB 1 PLAYER - RIGHT

2 PLAYER - STRONG 1 PLAYER - STRONG 2 PLAYER - FIERCE 1 PLAYER - FIERCE NIC NIC NIC GND.

“NOTE ; FOR CABINETS EQUIPPED WITH CAPCOM® “Q” SOUND, AUDIO CONNECTIONS ARE MADE THROUGH THE A-CARTRIDGE WITH RCA-TYPE CONNECTORS.

Auxiliary Cable (P/N 03-0052) Connections

WIRE COLOR CONNECTOR ODD ROW

NIC N/IC CONNECTOR EVEN ROW

NIC

NIC N/IC PURPLE/YELLOW PLAYER 2 KICK-ROUNDHOUSE NIC NIC PINK PLAYER 1 KICK-ROUNDHOUSE RED PLAYER 1 KICK-FORWARD BLUE PLAYER 1 KICK-SHORT. GRAY/YELLOW PLAYER 2 KICK-SHORT

PINK/YELLOWPLAYER 2 KICK-FORWARDNIC

NIC NIC NIC NIC

GRAY/YELLOWTEST BRKT-VOLUME UPTEST BRKT-VOLUME DOWN _| PINK/YELLOW
BLACK/WHITETEST BRKT-VOLUME COMMONNIC

BLACK

Page 18 PLAYER 2 KICK - COMMON

Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN.O1 PLAYER 1 KICK-COMMON

Page 23

—_~ 1-3/16" DRILL FOR PLAYER HOLE

1-3/4" DRILL FOR JOYSTICK HOLE STRONG FIERCE

FORWARD

1-3/16" DRILL FOR BUTTON HOLES a FORWARD DEFENSE

OFFENSIVE CROUCH

CAPCOM , INC. ° 3311 NORTH KENNICOTT RD tr. ARLINGTON HEIGHTS ILLINOIS 60004 FORWARD

DRILL HOLE TEMPLATE, STREETFIGHTER ALPHA

500100 DRAWN BY: JA

DATE: 06/16/95 REVISION NO:

Page 24

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 25

@APEONI° coin-op, INC. Street Fighter™: Alpha

REFERENCE INFORMATION

GAME CASE CONTROLS

COIN REGISTER COMMUNICATION PORTS aon ay ee SED) (NOT USED) OUT IN

\ eo TEST:

VOLUME DOWN

JAMMA AUXILIARY CABLE AUDIO OUT os BY, SOUND)

CONNECTOR CONNECTOR RIGHT: RED, LEFT: WHITE

‘300800

TYPICAL CONTROL PANEL LAYOUT OF Street Fighter™: Alpha

[Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 26

NOTICE

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.

WARNING

Federal law provides severe civil and criminal penalties for the unauthorized reproduction, distribution, or exhibition of copyrighted audiovisual works and video games.

The Federal Bureau of Investigation investigates allegations of criminal copyright infringement.

CAIRCOMYY COIN-OP, INC. 3311 N. Kennicott Road Arlington Heights, Illinois 60004 Phone: (708) 797-6100 Fax: (708) 797-6306

Copyright © 1995 CAPCOM@coin-op, inc., All Rights Reserved