CATHODE RAY TOMES

Sky Kid

Sky Kid (new version) (Namco, 1985) · Document · 3 pages · 2 sections · original scan

Page 1

é

Conversion Kit For Horizontal Monitor Games

Lr te KITKO RP” 2250 Elmhurst Ad. « Elk Grove, I. 60007 » (312) 228-0451 <a Fax: (312) 228-1563 © Telex: 206424 Kitkorp

Page 2

SKYKID

CONVERSION INSTRUCTIONS

Skykid will go into any cabinet that has a horizontal-mount monitor and a Power supply that supplies +5 volts DC and +12 volts DC. The control panel requires two 8-way joysticks, left and right "Shoot" and "Loop/Bonb" buttons, and Player 1 and 2 Start buttons. The PC board generates a negative composite sync signal that is compatible with the majority of monitors in use.

  • Remove all the old game graphics: marquee, side decals, instruction decals, etc.
  • Remove old buttons and joystick from the control panel. Strip off the old overlay, if any, Drill additional holes for buttons if needed, or plug extra holes. See “Suggested Control Panel Layout” diagram.
  • Remove the old game wiring harness, but leave all the AC wiring.
  • Apply the Skykid control panel overlay to the control panel. Cut away excess and cut out button holes and joystick holes with sharp knife.
  • Apply the Skykid button labels. Install the new buttons and joystick.
  • Cut the Skykid marquee to size and install it. Apply the rest of the decals to the cabinet.
  • Wire the Skykid cable harness into the cabinet. Note that the power supply wires are heavier gauge. This is to insure good power distribution.
  • Mount the Skykid PC boards in the game cabinet. Plug in the cable harness connector. The letter “A” on the connector housing indicates the top (or parts side) of the board. It should be near the letter “A” printed on the board.
  • Double check your wiring. Install the FCC enclosure.

VIDEO CONNECTOR J6 VIDEO RED [+) © VIDEO SYNC LC] VIDEO PLUG RED WHITE [] «ror useo) WiDEO GREEN ® @] vioED GROUND oOo VIDEO BLUE AB BLUE DIPSWITCHES

  • This board generates negative composite sync. The white sync output wire goes to both the horizontal and vertical negative composite sync inputs on the monitor.
  • Connector J7 on the board is not used.

SUGGESTED CONTROL PANEL LAYOUT

LOOP) LOOP’ SHOOT BOMB IB er OOLrOO

1P START 2P START

Page 3

SKYKID EDGE CONNECTOR DIAGRAM

PARTS SIDE

  • SERVICE SWITCH

YEL_COINSWITCH 1

GRY-BLK 1P START

GEN~GRN 1P SHOOT

YEL~RED 1P LEFT

YEL-BLI1_1P DOWN

YEL~GRN_1P RIGHT

x

NOTES: [R [ta] 2P RIGHT ORG-GRY | s [15] 2PUP__ORG-BRN

  • COIN COUNTER 2 | Y 121 GOGKTAIL TABLE i SOLDER SIDE

SPKR- VIO-BLK

COINSWITCH 2 :

2P START GRY-THT

2P SHOOT GRY

2P LEFT ORG-RED

2P DOWN ORG-BLU

P.S. GROUND |z |22 PS GROUND YEL

  • All wires are 22 gauge, except power supply wires which are 18 gauge.
  • For use in cocktail table, ground pin 21.
  • Pins marked * are not wired and are for optional use. 4, Supply voltage for coin lockout coils and coin counters is +12 volts DC.
CAUTION: DO NOT CONFUSE THE TWO YELLOW POWER SUPPLY GROUND WIRES WITH THE YELLOW CCINSWITCH WIRE AT K.

DIPSWITCH A [+ fe[sTa[s le [7 is] [sertex On [on] ser ||| [TT Coins/Credit #1 ws | __jorr [te V2

an Ts

[el a Screen Freeze Yes

Coin/Creda #2 Ww

DIPSWITCH B Hof Lives 3 |OFFIOFF

Screen invent

CAUTION: DO NOT CONFUSE THE TWO YELLOW POWER SUPPLY GROUND WIRES WITH THE YELLOW COINSWITCH WIRE AT K.