CATHODE RAY TOMES

Street Fighter EX 2

Street Fighter EX2 (Europe 980312) (Capcom / Arika, 1998) · Manual · 16 pages · 13 sections · original scan

Page 1

© ARIKA CO., LTD. 1998, © CAPCOM CO., LTD. 1998, © CAPCOM U.S.A., INC. 1998 ALL RIGHTS RESERVED.

OPERATORS MANUAL

WARNING

This game is for use in the United States of America and Canada. Sales, export or operation outside of these countries may be constructed as copyright and trademark infringements and is strictly prohibited. Violators are subject to severe penalties and will be prosecuted to the full extent of the law.

SFET1300 050598

Page 2

® C@APEON coin-op, inc. STREET FIGHTER EX2™

THANK YOU FOR PURCHASING STREET FIGHTER EX2 ™ WE INVITE YOU TO USE THE FOLLOWING MAILING ADDRESS, TELEPHONE OR FAX NUMBER FOR PARTS OR SERVICE INFORMATION CONCERNING THIS GAME:

CAPCOM® COIN-OP, INC. ATTN: CUSTOMER SERVICE 475 OAKMEAD PARKWAY SUNNYVALE, CA 94086 PHONE: (408) 522-5325 FAX: (408) 522-5331

THE SERIAL NUMBERS OF YOUR GAME ARE LOCATED ON THE PRINTED CIRCUIT BOARDS AS SHOWN BELOW. PLEASE HAVE THESE SERIAL NUMBERS AVAILABLE WHEN CONTACTING US FOR SERVICE INFORMATION.

PLEASE RECORD THE PC BOARD SERIAL NUMBERS HERE:

  • LOWER PC BOARD - SOLDER SIDE: AAMA SERIAL NUMBER:
  • LOWER PC BOARD - COMPONENT SIDE: CAPCOM SERIAL NUMBER:

L Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 3

CAPCOM’ cow.op, INC. TABLE OF CONTENTS

Caution

Warranty Information

Kit Inspection, Kit parts List

Kit Installation Preparation Installation Marquee Control Panel Overlay Control Panel Component Cabinet Decals PC Board Installation System Wiring Control Panel Test/Volume Bracket Speakers Q-Sound Modification PC Boards

Test Menu & Game Adjustments Test Menu Accessing the Menu How to Select an Item Closing the Menu Menu Item Descriptions Configuration Menu System Configuration Game Configuration

Reference Information JAMMA Connections Auxiliary Cable Connections

CAUTION STREET FIGHTER EX2™

ownnnny

oO eB OO

OWDABDAAHAH

Please read the following instructions to keep the PC boards in good condition:

° Do not drop or bump the boards. ° Do not spill any liquids on the boards.

DISASSEMBLING THE BOARDS OR REMOVING STICKERS MA

CAUSE THE TERMINATION OF YOUR REPAIR WARRANTY.

[ Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 4

® CAPEOM* coin-op, inc. STREET FIGHTER EX2™

LIMITED PRODUCT WARRANTY (APPLIES TO DOMESTIC SALES ONLY)

CAPCOM® COIN-OP, INC. (Seller), warrants only to the initial purchaser of its products, that the items listed below are free from defects in material and workmanship under normal use and service for the warranty periods specified:

A. Printed Circuit Boards: Ninety (90) Days B. Electronic and Mechanical Components: Ninety (90) Days

No other part of Seller's products are warranted.

Warranty periods are effective from the initial date of shipment from seller to its authorized distributors.

Seller's sole liability shall be, at its option, to repair or replace products which are returned to Seller during the warranty periods specified, provided:

A. Seller is notified promptly upon discovery by buyer that stated products are defective;

B. Such products are properly packaged and then returned, prepaid to Seller's designated plant.

This warranty does not apply to any parts damaged during shipment or handling, or due to improper installation or usage, or alteration. In no event shall Seller be liable for any anticipated profits, loss of profits, loss of use, incidental or consequential damages or any other losses incurred by the customer in connection with the purchase of a CAPCOM® COIN-OP, INC. product.

WARRANTY DISCLAIMER

EXCEPT AS SPECIFICALLY PROVIDED IN A WRITTEN CONTRACT BETWEEN SELLER AND PURCHASER, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

IMPORTANT NOTICE

THIS SHIPMENT HAS BEEN CAREFULLY INSPECTED AND PROPERLY PACKAGED BEFORE LEAVING THE FACTORY. WE CANNOT ASSUME RESPONSIBILITY FOR BREAKAGE THAT MAY OCCUR DURING TRANSPORTATION OF THE GAME. IF THIS GAME IS DAMAGED UPON RECEIPT FROM THE CARRIER, IMMEDIATELY NOTIFY THE CARRIER AND FILE A DAMAGE REPORT.

ii Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 5

® CAPCOL" coin-op, inc. STREET FIGHTER EX2™

KIT INSPECTION

Check that all of the following parts have been shipped with your kit. If any parts are missing, contact your distributor immediately.

PART NO. DESCRIPTION

SFET1400 Assy, PCB, PSX System, “STREET FIGHTER EX2” 13-0154 Standoff w/Screw, PCB Mounting 03-0104 «| Harness, Stereo Speaker

03-0105 Cable, Auxiliary SFET1110 Marquee, “STREET FIGHTER EX2” SFET2520-01 | Decal - Top, Game Play Inst., “STREET FIGHTER EX2” SFET2520-02 | Decal - Bottom , Game Play Inst., “STREET FIGHTER EX2” AW00245-2 Decal, Joystick & Button Switches, “STREET FIGHTER EX2” SFET1300 Manual, Operators, “STREET FIGHTER EX2” AW00147 Decal, Cabinet Side GE1200 Monitor Card PL00376 Plex, Marquee, Clear, 27.0 x 9.0 x 1/8” AW00216 Overlay, Control Panel GE2030 Joystick, 8 Way 16-0130 Switch, 1-Player Start Button (White) 16-0131 __| Switch, 2-Player Start Button (White) 16-0133 Switch, Button (Red) 16-0134 Switch, Button (Blue) 16-0136 Switch, Button (Green) i 2} 2/2} 4/2) ele) ele) 44) 24fe4)2}e)/ 4) a4 efadal ele] ple) ele) rf e} eel el el ey} el ale

Note: Because of availability, your kit may contain different color of push-buttons.

Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC. 1

Page 6

CAPCOM’ co-op, INC.

KIT INSTALLATION

WARNING:

MAKE SURE ELECTRICAL POWER TO THE GAME IS OFF BEFORE STARTING THE KIT INSTALLATION.

PREPARATION

  • Disconnect and remove the old printed circuit board(s) from the cabinet.
  • Remove or open the control panel, and disconnect and remove the buttons and joystick(s) from the contro] panel.
  • Remove any covering from the control panel overlay, and then remove the control panel overlay.
  • Determine where any new holes should go. Center punch any needed new holes on the control panel.
  • Cut out the new holes using a 1-3/16" hole saw.
  • If there is an additional control panel cover, Figurel (such as plastic or lexan) that will be utilized, cut any additional holes using the same template. *Cover is not included in the kit.
  • Plug up unused holes with a wood dowel and sand any rough edges. (1-1/8" diameter)

INSTALLATION

Marquee Installation

  • Remove the marquee plexi glass, marquee overlay, and the cabinet graphics.
  • — Install the new marquee and replace the plexi glass. Clear plexi glass is included in “Full” kit.

Control Panel Overlay Installation (See Figure 1)

  • The control panel overlay in the kit is oversized to accommodate most control panel sizes. Center the overlay on the control panel, leaving some excess material at the edges.
  • Remove the protective backing from the overlay and press it down on the control panel, keeping it properly aligned. Press it down firmly, smooth out any bubbles, and press it over the edges. STREET FIGHTER EX2™
  • Trim any excess from the overlay. Place the drill hole template on top of the overlay, aligning it with the joystick holes. Pierce through the overlay at each control panel hole. Then, cut away overlay material covering the joystick and button holes. Remove the template and clean off the overlay.
  • Peel off the backings of the 4-button and joystick decals, aligr over the control panel holes, and press in place on the overlay (refe to the drill hole template for proper placement). Using a knife, trim material from the center hole of the joystick decal.
  • Install the control panel cover, FIG.1. (if required).

Overlay (Trim to size)

Figure 1: Overlay Installation

Re-assembly of Components

  • Notice that there are two white buttons. See Figure 2. The WHITE buttons are START buttons. Install the PLAYER ONE button on the top left-hand side of the control panel, and the PLAYER TWO button on the top right-side of the control panel.

4 Player 7 2 Player

\Z WP

Figure 2: Start Buttons

2 Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 7

© GAPEOM" cow-op, inc. STREET FIGHTER EX2™

Red Green Blue Red Green Blue

& | & iy 838 toro}

Red Green Blue Red Green Blue

Retaining GS) Rings Switches —— cF 2B

Figure 3: Control Panel Buttons and Switches

  • Install all buttons and retaining rings on the control panel as shown in Figure 3. Install two RED buttons to the immediate right of each joystick, install two GREEN buttons to the right of the red ones.
  • Install the switches on the buttons as shown in Figure 2. Orient the switches so that when a button is pressed, the red contact on the switch is depressed.
  • Install the joysticks on the control panel as shown in Figure 4.

Figure 4: Joystick Installation CABINET DECAL INSTALLATION

  • | Remove monitor glass and install monitor card
  • Peel-off the backing to the instruction decals and place on both the top and bottom of the monitor card. (See Figure 5). Also, apply the cabinet decals to both sides of the cabinet.

Figure 5: Cabinet Decal Installation

CONTROL PANEL WIRING

NOTE: All switch wires used in this game must be wired to the normally-open connection on the switches. Each switch requires a ground wire on the common connector and the appropriate control or switch wire on the normally-open connector of the switch.
  • Reconnect the existing JAMMA connectors to the control panel according to the chart in Page 10.
  • Connect the Player 1 and the Player 2 KICK buttons to the auxiliary cable harness as shown in Figure 6. Make the connections according to the chart in Page 10.

Figure 6: Auxiliary Cable Harness

Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC. 3

Page 8

® CAPCOM co-op, inc. STREET FIGHTER EX2™ TEST/VOLUME BRACKET WIRING

  • An optional Test Switch bracket (see Figure 7) is available through your distributor. (CAPCOM Part number 03-0050). Your cabinet may already contain this bracket. When installing, the bracket should be mounted inside the coin door and on top of the cash box for easy access.
NOTE: Only the Test switch is used for this game; the Volume Up/Down switches are not used.

Volume adjustments must be made through the volume control knob located on the PC board.

Figure 7: Test Switch Bracket

Wiring of the Test Bracket requires connections to the main JAMMA harness as shown in Table 3:

COLOR FUNCTION TO YELLOW OLUME-UP NO CONNECTION BLACK VOLUME- NO CONNECTION DOW GREEN COMMON BROWN TEST

BLACK GROUND

Table 3: Test Bracket Wiring Chart NO CONNECTION JAMMA “15' JAMMA “A” or “B” or “e” or “f or “1” or “9” or “27” or “28”

SPEAKER WIRING

24a.If you are converting a cabinet that is not equipped with CAPCOM® Q-SOUND, the leads from the speaker harness (supplied with this kit) must be wired to the cabinet speakers according to the TABLE 4. LEFT LEFT (.) RIGHT () RIGHT (+)

Table 4: Speaker Wiring Chart

24b. If you are converting a cabinet that is equipped with CAPCOM® Q-SOUND, you may elect to wire directly to the cabinet speaker terminals, as shown above, or you can obtain the same result by performing the following modification (see Figure 8):

  • Disconnect the speaker harness connector from the Q-SOUND board at location CB8.
NOTE: EXTERNAL Q-SOUND POWER AMPLIFIER MUST DISCONNECTED WITH THIS PSX SYSTEM PCB.

ii) Install a 4-pin, 0.156 inch diameter header connector (not supplied with this kit; purchase locally) onto the speaker harness connector.

iii) Insert each wire lead from the supplied speaker harness to each corresponding pin from a 4-pin, 0.156 inch diameter female connector (not supplied with this kit; purchase locally).

iv) Push the female connector and the header connector pins together.

  • Your cabinet is now equipped to receive stereo sound from the PC board.

TO CABINET SPEAKERS

EXISTING SPEAKER HARNESS. CONNECTOR

TO GAME 4-PIN PC BOARD, be deslail LOCATION CONNECTOR 4 oi CN 504 FEMALE Ny CONNECTOR vveoseo SUPPLIED SPEAKER HARNESS.

Figure 8: Q-SOUND Modification

4 Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 9

CAP@OM’com-op, INC. PC BOARD INSTALLATION

  • Install the four (4) mounting standoffs to the underside of the PC board by securing with the supplied machine screws. Then, fasten the PC board standoffs to the control panel shelf with wood screws, as shown in Figure 11.

Wood Screws are not included in the kit.

WOOD SCREW

  • ——. ‘STANDOFF

Figure 9: PC Board Mounting

PC BOARD WIRING CONNECTIONS AND ADJUSTMENTS

  • Connect the JAMMA harness connector to the edge connector located on the bottom PC board (see Figure 10). STREET FIGHTER EX2™

WARNIMG

IMPROPER INSTALLATION OF THE JAMMA HARNESS CONNECTOR TO THE PC BOARD WILL CAUSE DAMAGE TO THE PC BOARD.

  • Attach the auxiliary cable connector to the top PC board at location CN2 (see Figure 10).
  • Attach the speaker harness connector to the PC board at location CN504 (see Figure 10).
  • Check that the mode switch, on the lower PC board, is set to “STEREO” (see Figure 10).
  • Check that all 4 positions of the DIP switch are set to OFF (see Figure 10).
  • Power-up the game and adjust the speaker volume by turning the Volume Control knob clockwise to increase volume, or counterclockwise to decrease volume (see Figure 10).
  • Set all operator adjustable options by pressing the TEST switch. Follow the instructions under the TEST MENU section of this manual.

Figure 10: PC Board Wiring Connections & Adjustments

Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 10

® CAPCOM coin-op. inc. STREET FIGHTER EX2™

TEST MENU The test menu allows you to test the functions and configure the game. These items include input devices such as joysticks, buttons and coin door or switches, output devices such as monitor, speakers and meters. Through the Test Menu you can also access the Configuration Menu, where you can change the settings of the game.

TEST

INPUT

OUTPUT

SOUND

COLOR 2.

3.

4.

5.

6.

7.

8.

9. EXIT GAME DATA CONFIGURATION PLAYER 1 SHOT 1 button, as shown below in various

  • ACCESSING THE TEST MENU MENU + For a CAPCOM cabinet, or a cabinet with a test switch: Make sure the game is on and push the test switch. The screen shown left will appear. + For a cabinet without a test switch: You need install test switch to your cabinet. Please refer Page 4 for test switch installation.

DOT CROSS HATCH 2. HOW TO SELECT AN ITEM + Use the PLAYER 1 JOYSTICK to move the arrow in front of the desired item and press the

control panel configurations: MEMORY CHECK

  • CLOSING THE TEST MENU To close the Test Menu, highlight “9. EXIT” and push the PLAYER 1 SHOT I button. UP or DOWN P SHOT1

Player 1 Joystick Player 1 Start + To return to the test menu, push the PLAYER 1 START and PLAYER I SHOT 1 buttons simultaneously. + The test menu will always return to the screen: bie Se Player 1 Shot 1 Player 1 Shot 2

  • After you exit the “7. CONFIGURATION MENU” and
  • After the memory is tested from the menu, “8. MEMORY CHECK”.

Punch Light Punch Medium

  • TEST MENU ITEM DESCRIPTIONS

INPUT Used to test all the input switches, such as joysticks and buttons. The “0” changes toa “1” as the button is pushed or joystick is moved. Check connections and switches in case the “0” doesn’t change to a “1” when depressed or moved. OUTPUT Used to test the coin meter and the coin lock. SOUND Select a code of SOUND with the PLAYER 1 JOYSTICK. Push the PLAYER 1 SHOT 1 button to hear the sound of the selected code. COLOR Shows color bars of red, green, blue, and white. Adjust RGB and brightness to obtain the optimum color balance and solid black background. DOT CROSS HATCH | Used to test the screen size, focus and distortion. GAME DATA Coin meter, Free play and Average Time information will be displayed. CONFIGURATION Used to change the game play settings. Refer to the CONFIGURATION MENU section. MEMORY CHECK. Used to test memory. “OK” appears when each block of memory passes test, “NG” appears in case of malfunction. If“NG” appears, repeat the memory test and wait for the “OK” message. Contact your distributor if “NG” still appears. EXIT Select this item and push the PLAYER 1 SHOT J button to return to game play mode.

6 Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 11

@AP@OIN coin-op, inc. STREET FIGHTER EX2™

CONFIGURATION MENU

The Configuration Menu is used to change various game settings such as level difficulty, credits, sound configuration, etc. These settings are stored in memory on the PCB.

The Configuration Menu is divided into 2 sections. In the SYSTEM section, you can change credits, sound, and coin door configurations. In the GAME section, you can change the play difficulty level and duration of the game.

  • ACCESSING THE CONFIGURATION MENU : From the TEST MENU, move the arrow to “7, CONFIGURATION” and push the PLAYER 1 SHOT 1 button. The screen left will be displayed. A description of each option is explained in the table below.

SYSTEM

GAME

DEFAULT

SAVE & EXIT

SELECT = 1PUPOR DOWN START = 1PSHOT1

  • CONFIGURATION MENU ITEM DESCRIPTIONS

SYSTEM | Select this item to change settings for credits, sound and coin door configurations. GAME Select this item to change difficulty level, damage level, time count speed, maximum number of rounds and event type. Use this item to restore configuration settings to the original factory values. Press the PLAYER 1 SHOT 1 and PLAYER 1 SHOT 2 buttons at the same time to restore default values. Use this to save new configuration settings and exit to the Test Menu. The message “SAVING NEW CONFIGURATION IN EEPROM” will appear while the new settings are being saved. DO NOT turn power off to the game until “SAVING” is complete and the Test Menu reappears. DEFAULT

SAVE & EXIT

Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC. 7

Page 12

® QANPRONT"comn-or, inc. STREET FIGHTER EX2 ™

SYSTEM CONFIGURATION

7-1. SYSTEM CONFIGURATION CHANGING THE SYSTEM

COIN MODE

CHUTE TYPE

CONTINUE

DEMO SOUND

SOUND MODE

REGULATION

EXIT 2COIN 1 CREDIT

2 CHUTES SINGLE

ON

ON

STEREO (Q SO

ON CONFIGURATION SETTINGS

Move the PLAYER 1 JOYSTICK up or down to

highlight the desired option. Once the option

is highlighted, move the PLAYER 1

JOYSTICK left or right or press the PLAYER

1 SHOT 1 button to select.

SELECT OPTION MODIFY SETTING = 1P UP OR DOWN = 1P LEFT OR RIGHT = 1P SHOT1 OR SHOT2

SYSTEM CONFIGURATION ITEM DESCRIPTIONS

  • COIN MODE. SELECT THE CHARGE PER PLAY.
  • CHUTE TYPE SELECT THE NUMBER OF PLAYER(S) AND COIN CHUTES. 1 CHUTE SINGLE: WITH THIS SETTING, EITHER PLAYER CAN START THE GAME. 2 CHUTES SINGLE: TWO PLAYERS USE ONE COIN CHUTE AND PLAY AT THE SAME TIME. THE PLAYER WHOSE COIN WAS PUT IN FIRST STARTS THE GAME. 2 CHUTES MULTI: TWO PLAYERS USE TWO COIN CHUTES AND PLAY SEPARATELY. THE GAME STARTS FROM THE SAME SIDE AS THE COIN CHUTE WAS USED.
  • CONTINUE SELECT ON FOR CONTINUOUS PLAY OR OFF FOR NON-CONTINUOUS PLAY.
  • DEMO SOUND TURNS ATTRACT SOUNDS ON OR OFF.
  • SOUND MODE SELECT STEREO(Q SOUND) OR MONAURAL FOR USE WITH YOUR CABINET.
NOTE: STEREO(Q SOUND) SHOULD ONLY BE SELECTED WHEN THE CABINET SPEAKERS HAVE BEEN CONNECTED TO THE GAME PC BOARD AT LOCATION CN504. SEE PAGE 4, SPEAKER WIRING. EXTERNAL Q-SOUND POWER AMPLIFIER IS NOT USED FOR THIS GAME. (SEE PAGE 6 FOR DETAILS)
  • REGULATION IF SET TO “ON” THE COLOR OF THE BLOOD CHANGES FROM RED TO GREEN.
  • EXIT TO SAVE THE SETTINGS AND RETURN TO THE CONFIGURATION MENU, HIGHLIGHT THIS ITEM AND PUSH EITHER THE PLAYER 1 SHOT 1 BUTTON OR THE PLAYER 1 SHOT 2BUTTON.

SYSTEM CONFIGURATION OPTION SETTINGS

  • COIN MODE 1 COIN 1 CREDIT 1 COIN 2 CREDITS 1 COIN 3 CREDITS 1 COIN 4 CREDITS 1 COIN 5 CREDITS 1 COIN 7 CREDITS 1 COIN 8 CREDITS 1 COIN 9 CREDITS 2 COINS 1 COIN | 1 CREDIT 6 CREDITS 4 COINS 1 CREDIT. 5 COINS 1CREDIT 6 COINS 3 COINS | 1 CREDIT 1 CREDIT 8 COINS 9 COINS 1CREDIT 1 CREDIT. 2 CHUTES SINGLE 2 COINS START 1 COIN CONTINUE 2 CHUTES MULTI FREE PLAY

1 CHUTE SINGLE OFF OFF MONAURAL STEREO (Q SOUND)

  • REGULATION
NOTE:

8 Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 13

® CAPCOM COIN-OP, INC. STREET FIGHTER EX2™

GAME CONFIGURATION

7-2. GAME CONFIGURATION

DIFFICULTY

DAMAGE LEVEL

TIME COUNT

MAX-ROUND[CPU]

MAX-ROUND[VS]

EVENT EASY[

LOWL..

SLOW[.2..]FAST

3 ROUND

3 ROUND

OFF

EXIT

SELECT OPTION MODIFY SETTINGS

  • DIFFICULTY P UP OR DOWN P LEFT OR RIGHT 1P SHOT1 OR SHOTZ,

DESCRIPTION SETS THE GAME DIFFICULTY LEVEL CHANGING THE GAME CONFIGURATION SETTINGS

Move the PLAYER 1 JOYSTICK up or down to highlight the desired option. Once the option is highlighted, move the PLAYER 1 JOYSTICK eft or right or press the PLAYER 1 SHOT 1 button to select.

OPTION SETTINGS 2 3

  • DAMAGE LEVEL SETS THE OFFENSIVE POWER LEVEL.
  • TIME COUNT SPEED SETS THE SPEED OF COUNTDOWN FROM THE TIMER DISPLAY.
  • MAX-ROUND (VS. CPU) SET THE NUMBER OF ROUNDS PER MATCH FOR VS. “CPU” DEFAULT IS SET AT 3 ROUNDS. 1 ROUND
  • MAX-ROUND (VS. PLAYER) SET THE NUMBER OF ROUNDS PER MATCH FOR VS. “PLAYER” DEFAULT IS SET AT 3 ROUNDS. 1 ROUND AND 5ROUNDS ARE CONVENIENT FOR. A GAME EVENT (TOURNAMENT ETC.). 1 ROUND
  • EVENT SPECIAL SETTING FOR TOURNAMENT EVENT.

GAME. THE GAME ENDS AFTER ONE MATCH 1 MATCH: ONLY ONE CREDIT IS REQUIRED FOR A 2P

REGARDLESS OF THE RESULT.. RETURN TO THE CONFIGURATION MENU.

NOTE: FACTORY

Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 14

® CAPCOM COIN-OP, INC. STREET FIGHTER EX2™

JAMMA Connections

SOLDER SIDE COMPONENT SIDE

GND

COIN COUNTER 1

NIC. COIN LOCK 1

NIC. ‘VIDEO GREEN VIDEO SYNC SERVICE (FREE CREDIT)

VIDEO RED

VIDEO BLUE VIDEO GROUND NIC 2 PLAYER

  • COIN 2 PLAYER
  • START 2 PLAYER
  • UP 2 PLAYER
  • DOWN 2 PLAYER
  • LEFT 2 PLAYER
  • RIGHT 2 PLAYER
  • LIGHT PUNCH

2PLAYER - HEAVY PUNCH NIC

  • MEDIUM PUNCH mOoRO TO NMM EAM CHAwDYA Ee DIAGNOSTICS

1 PLAYER _- UP 1 PLAYER _- DOWN 1 PLAYER _- LEFT 1 PLAYER _- RIGHT

Auxiliary Cable (P/N 03-0105) Connections

WIRE COLOR CONNECTOR ODD ROW CONNECTOR EVEN ROW WIRE COLOR

NIC NIC NIC NIC NIC NIC NIC NIC

PURPLE/YELLOW_|PLAYER 2 HEAVY KICKNIC

NIC NIC NIC NIC

PINKPLAYER 1 HEAVY KICKNIC
RED| PLAYER 1 MEDIUM KICKNIC
BLUEPLAYER 1 LIGHT KICKNIC
GRAY/YELLOWPLAYER 2 LIGHT KICKNIC

PINKYELLOW PLAYER 2 MEDIUM KICK NIC

NIC NIC NIC NIC NIC NIC NIC NIC

BLACKPLAYER 2 KICK - COMMON,PLAYER 1 KICK-COMMONBLACK

10 Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 15

CAPCOM’ co-op, inc. STREET FIGHTER EX2™

REFERENCE INFORMATION

PC BOARD CONNECTIONS AND CONTROLS

Auxillary Cable Test Switch Connector (Not Used)

Volume Control Knob RS Speaker Harness. Connector

TYPICAL CONTROL PANEL LAYOUTS FOR “STREET FIGHTER EX2 7

eee

v1600200

L Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 16

NOTICE

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.

WARNING

Federal law provides severe civil and criminal penalties for the unauthorized reproduction, distribution, or exhibition of copyrighted audiovisual works and video games.

The Federal Bureau of Investigation investigates allegations of criminal copyright infringement.

CAIRCOMY COIN-OP, INC. 475 Oakmead Parkway Sunnyvale, CA 94086 Phone: (408) 774-0500 Fax: (408) 522-5331

Copyright © 1998 CAPCOM ® coin-op, inc., All Rights Reserved