Motorace USA Instruction Manual (16-3024-101)
Traverse USA / Zippy Race (Irem, 1983) · Instruction Manual · 22 pages · 26 sections · original scan
16-3024-101
Williams Instruction Manual
(“od a aa bi ce
OPERATION ADJUSTMENTS DIAGNOSTICS PARTS
= <>
- ee ie
[L ie EIN
ROM SUMMARY
PART NO. DESCRIPTION
MS2-A CPU 4(3L) 2 (3K) 3 (3) A-5343-40373
A-5343-10374
A-5343-10375 8K x 8 EPROM
8K x 8 EPROM
8K x 8 EPROM
| MS52-B Character | 4 (3N) | A-5343-10376 | 8K x 8 EPROM |
| 5 (3M) | A-5243-10377 | 8K x 8 EPROM | |
| 6 (3K) | A-5343-10378 | 8K x 8 EPROM | |
| 14 (AF) | A-5282-10383 | 32x 8 PROM | |
| 42 (2H) | A-5282-10384 | 256 x 4 PROM | |
| M52-F Scrolling Video | 7 (3E) | A-5343-10379 | 8K x 8 EPROM |
8(3C) | A-5343-10380 8K x 8 EPROM
| 9 (3A) | A-5343-10381 | 8K x 8 EPROM | |
| 43 (1F) | A-5282-10385 | 32x 8 PROM | |
| 44 (1H) | A-5282-10386 | 32x 8 PROM | |
| M52-S Sound | 40 (1A) | A-5343-10382 | 4K x 8 EPROM |
INSTRUCTION MANUAL
FOR UPRIGHT AND TABLE GAMES
including...
eoperation e adjustment
¢ diagnostics
eparts
©1983 WILLIAMS ELECTRONICS, INC.
CONTENTS
@ CHAPTER 1 Game Sefup...............0..0.. 00sec eee eens 5&6 Warnings & Notices. .... 2.0.6.0 c cece cece tenet ene e tener e eens 6 Location of Controls. 6
Examine Your Game.............055 ann 6
@CHAPTER 2 Game Operation............ 0.0.6.0 ccc ce cee eee 710 Power TUM-ON. .... cece een tenet tenet teeter ee 8
Game Operation. .... 666 eee rere eect eee eee eet teen ees 8
Game AdjUstMeNts ..... cece eee eee eee eee nents 8
Dip Switch Settings. ......... 0.0 cece cece eee ece eee ee ee ee eee ceentennes 40
CHAPTER 3 Troubleshooting Procedures ......................45 "16 Introduction... 66... e rete eee 12 Powelr-Up Tests... 2... ieee cece rn erent eee eee ence eine eee ee 12 PHOQMOSHCS ose eerie sisie sete e wicie crepe ig neta nye nsete e ecnray oe ble tat eile wee 12 +5VDC Power Supply Adjustments... 16
@CHAPTER 4 Parls.....2.. 1. ieee cece eee eee eee n een e nee e ee 47-20
CHAPTER 1 Game Setup
Warnings & Notices Location of Controls
Examine Your Game
Warnings & Notices
- FOR SAFETY AND RELIABILITY, WILLIAMS does not recommend or authorize any substitute parts or modifications of WILLIAMS equipment.
- USE OF NON-WILLIAMS PARTS and modifications of game circuitry may adversely affect game play, or may cause injuries.
- SUBSTITUTE PARTS, MODIFICATIONS AND GAME “CONVERSIONS” may void FCC type-acceptance.
- SINCE THIS GAME IS PROTECTED by Federal copyright, trademark and patent laws, so-called game “conversions” may be illegal under Federal law.
- THIS “CONVERSION” PRINCIPLE ALSO APPLIES to unauthorized facsimiles of WILLIAMS equipment, logos, designs, publications, assemblies and games (or game features not deemed to be in the public domain}, whether manufactured with WILLIAMS components or not.
RF INTERFERENCE NOTICE:
CABLE HARNESS PLACEMENTS AND GROUND STRAP ROUTING on this game have been designed to keep RF radiation and conduction within levels accepted by FCC regulations.
TO MAINTAIN THESE LEVELS, reposition harnesses and reconnect ground straps to their original placemenis if they should be disconnected during maintenance.
Location Of Controls
THE ON-OFF SWITCH is situated on the top-left corner of upright games as you face the back of the cabinet. Table games have an on-off switch underneath the game.
THE VOLUME CONTROL is located on the top left corner of the sound board.
GAME ADJUSTMENT SWITCHES. Two 8-position dip switches are located on the CPU Board. They are accessible through a window in the microprocessor module and are used for game adjustments and for diagnostics.
Examine Your Game
When you teceive a new WILLIAMS game, examine it carefully before you power it up. Be sure it was delivered in good condition!
CIINSPECT THE OUTSIDE of the shipping carton and/or game cabinet for shipping damage.
(CLUPRIGHTS: UNLOCK AND SET ASIDE THE TOP-REAR PANEL. Undo the two trunk latches on the inside of the bottom door. Open the door. Now check circuitry.
(TABLE GAMES: Unlock the component door on the Player 2 side of the game. Carefully lower the door to the floor.
CARE CONNECTORS SECURELY ATTACHED? Reconnect any found loose. DON'T FORCE CONNECTORS. They're keyed and only fit one way. By the same token, take care: reversed edge-connectors can damage PC boards!
CARE PLUG-IN CHIPS FIRMLY-SEATED in their sockets?
CIUNWRAP THE POWER CORD coiled inside the cabinet. Now position the cord in the wood slot beneath the bottom door. (Table games: Drop the plug through the hole in the floor. DON'T PLUG IT IN YET!)
CISCRUTINIZE MAJOR SUBASSEMBLIES, such as the monitor, control panel, transformer board and power supply. Make sure they're securely-mounted.
CHAPTER 2 Game Operation
Power Turn-On
Game Operation Game Adjustments Dip Switch Settings
Power Turn-on
WHEN THE GAME IS FIRST TURNED ON it should come up in the attract mode. If not, refer to TROUBLESHOOT- ING PROCEDURES.
Game Operation
GAME START
INSERT COINS. Press either the one-player or twoplayer button. Two-player games require two credits.
PLAYER CONROLS. MOTORACE—USA is a game of teeth-gritting excitement. It requires fast, shrewd thinking...and more than anything else, adroit, appropriate and just plain quick maneuvering.
QUICK MANEUVERING means mastery of all your controls. You may have fo feint in one direction, hit the brakes, and surge forward in another!
*YOUR JOYSTICK steers your motorcycle precisely to the left or right. +YOUR BRAKE BUTTON can slow you down fast. *YOUR THROTTLE BUTTON is your friend as the highway opens up. Dare to surge forward! Your bike has just the right pickup. But be prudent when the traffic gets nasty or when the pavement's uncertain! *THROTTLE AND BRAKE at the same time and you can maintain a cruise speed.
GAME PLAY
YOU'RE IN L.A. TRAFFIC and you're prepared to defy all the odds. You're going to put that hammer down and highbali your 500cc motorcycle all the way to New York City. But the stakes are higher: You’re prepared to take on all the cars on the roadway...to outmanuever them all!
WITH ONLY YOUR WITS and your two wheels, you'll battle the ultimate American frontier: the open road, Your official checkpoints are Las Vegas, St. Louis, Chicago, and Houston...but you'll have to pick up some gas cans (500 points) along the way.
YOU'RE TAKING IT TO THE LIMIT, since you know that's how to earn the most points. But can your bike stand up fo the wheelies (700)...the rugged pathways and narrow bridges...the daredevil jumps (700) across challenging riverbeds? You're equal to the challenge! Forge ahead! HOW DO YOU KNOW WHERE YOU STAND? This is maddog competition, buf there are rules. Each time you improve your position you score 500. And at each checkpoint the standing you’ve achieved pays off in points and gas! But not all drivers are defensive drivers. If you should crash, you'll be penalized in your fuel allotment.
IN NEW YORK your bonus will be tallied based on your rank in the race and the amount of fuel you've conserved, But you're not done yet! A new race is on, and you're back in LA. Only this time you've got an even more-powerful bike!
4" RACE 500 cc moitorcyie 2° RACE 750 cc motorcycle 3° RACE 1200 cc motorcyle THEREAFTER | 1200 cc motorcyle
HIGH SCORE SIGNATURE. Select letters with the joystick and lock them in with the THROTTLE button.
GAME ADJUSTMENTS
Game adjustments are made using switches contained in DIP Switch 1 and DIP Switch 2 (Table 2) on the CPU Board (M52-A). Using a pen or small screwdriver, move switches to desired positions.
Switches 5, 6, 7, and 8 of DIP Switch 1 determine pricing rates as shown. Switch 3 of DIP Switch 2 selects Coin Mode 14 or Coin Mode 2 to go with the settings of switches 5, 6, 7, and 8 of DIP Switch 4.
Coin Mode 1 Is used for coin doors with a single coin chute or a set of coin chutes of equal value. Coin mode 2 is used for coin doors with two coin chutes of different values.
LA to VEGAS—25¢
HOW FAR THE PLAYER GETS can indicate whether game settings are bringing you a satisfactory return on your investment! You'll want to pay particular attention to players’ reception of the game for this reason: It takes about two minutes to get from LA to Vegas. We've found that two-minute games both satisfy players and also keep the quarters flowing.
Average players should almost get to Las Vegas (or make it part way to Houston) on their first quarter. If not, collections may not be at their peak. You'll want to tailor your game to your game-playing public. It’s easy. And it only takes a minute.
HOW TO MAKE GAME ADJUSTMENTS
USE DIP SWITCH BANK #1. Now for the multiple choice section. Choose one or more:
[1] For a shorter game, increase the AMOUNT OF FUEL LOST IN COLLISION. For a longer game, reduce it. See Table 1.
For a shorter game, change the FUEL CONSUMPTION from low to high (switch 3 on). For a longer game, change it from high to low (switch 3 off).
(If you have a lot of real pros that make it to Chicago or close to New York on a quarter (they're playing longer than six minutes), get rid of the CONTINUED-PLAY feature (switch 4 off). This will create a challenge to play even better. But... this is an important feature for both standings in the high score table and for more challenging races (larger and faster bikes). SO USE DISCRETION BEFORE SETTING SWITCH 4 ON.
Table 4. FUEL LOST PER COLLISION
PERCENT BANK 4 BANK 4 LOST MEANING DIP SWITCH #4 DIP SWITCH #2
| 8 | Low | OFF | OFF |
| 12 | Med | ON | OFF |
| 15 | High | OFF | ON |
| 418 | Max | ON | ON |
CHANGING GAME PRICING. MOTORACE—USA includes numerous pricing selections. For games that accept only one value of coin (“coin mode 4"), use Table 2 below to choose the appropriate price per game. Now set dip-switch bank #1 accordingly.
Refer to the table for other adjustments. Diagnostics test 01, the DIP Switch test causes most adjustments to be displayed on the monitor and may be used while making game adjustments. Dip Switch Bank 2
Dip Switch Bank 1 eleavre) ooooco0|
ZTeavezl dasobooq,
Figure 1. Dip Switches
DIP SWITCH NO. 4 Table 2. DIP SWITCH SETTINGS
SWITCH NUMBER ADJUSTMENT OPTIONS
| 4 | 2 | 3 | 4 | 5 | 6 | 7 | 8 |
+ RECOMMENDED
| SETTINGS | ON | OFF | OFF | ON | OFF | OFF | OFF | OFF |
| COIN MODE 4° | 6 PLAYS/4 COIN | OFF | OFF | ON | ON | |||
| 5 PLAYS/4 COIN | ON | ON | OFF | ON | ||||
| 4 PLAYS/1 COIN | OFF | ON | OFF | ON | ||||
| 3 PLAYS/4 COIN | ON | OFF | OFF | ON | ||||
| 2 PLAYS/4 COIN | OFF | OFF | OFF | ON | ||||
| + | 4 PLAY/4 COIN | OFF | OFF | OFF | OFF | ||||
| 4 PLAY/2 COINS | ‘ON | OFF | OFF | OFF | ||||
| 4 PLAY/3 COINS | OFF | ON | OFF | OFF | ||||
| 4 PLAY/4 COINS | ON | ON | OFF | OFF | ||||
| 4 PLAY/5 COINS | OFF | OFF | ON | OFF | ||||
| 4 PLAY/6 COINS | ON | OFF | ON | OFF | ||||
| FREE PLAY | ON | ON | ON | ON | ||||
| *COIN | CHUTE | 4 PLAY/1 COIN | OFF | OFF | ||||||
| MODE | A | 4 PLAY/2 COINS | ON | OFF | ||||
| 2 | 4 PLAY/3 COINS | OFF | ON | |||||
| FREE PLAY | ON | ON | ||||||
| B | 2 PLAYS/4 COIN. | OFF | OFF | |||||
| 3 PLAYS/4 COIN | ON | OFF | ||||||
| 5 PLAYS/4 COIN | OFF | ON | ||||||
| 6 PLAYS/4 COIN | ON | ON | ||||||
| PERCENT OF | 8.3% Low | OFF | OFF | |||||
| FUEL LOST | +| | 14.7% | ON | OFF | ||||
| IN COLLISION | 15.0% | OFF | ON | |||||
| 18.3% Max | ON | ON | ||||||
| FUEL | +| | LOW | OFF |
CONSUMPTION HIGH ON
CONTINUED NO OFF
| PLAY | + | YES | ON |
DIP SWITCH NO. 2
ADJUSTMENT OPTIONS asia niweee
| 4 | 2 | 3 | 4 | 5 | 6 | 7 | 8 |
*RECOMMENDED
| SETTINGS | OFF | ON | OFF | OFF | OFF | OFF | OFF | OFF |
| “FLIP | +| | NO | OFF | |||||
| PICTURE | YES | ON |
CABINET TABLE OFF
| TYPE | + | UPRIGHT | ON | |
| COIN MODE | +| | COIN MODE 1 | OFF |
| SETTINGS FOR | COIN MODE 2 | ON |
DIP SWITCH 4
| UNIT OF | +} | MILE | OFF |
| DISTANCE | KILOMETER | ON | |
| FREEZE | +| | NO | OFF |
| PICTURE | YES | ON | |
| DEMO MODE | +} | NO | OFF |
YES ON
| TEST MODE | *| | NO | OFF |
YES ON
| “SWITCH 6 | +| | No |
{not used) OFF «Recommended settings are indicated with bullets (+). “For games with a single coin selector or two selectors of the same value, switch 3 on Dip Switch 2 must be turned OFF. For games with selectors for two different coin values, switch 3 must be turned ON. “Switches 4 and 6 of Dip Switch #2 MUST BE SET TO OFF. +Permits a player to continue a game at the same point where he left off (on the previous coin).
CHAPTER 3 Troubleshooting Procedures
Introduction
Power-Up Tests Diagnostics
+5VDC Power Supply Adjustments
Certain types of game malfunctions may inhibit the game's diagnostic or display faculties. Troubleshooting procedures for most of these types of malfunctions as well as malfunctions INTRODUCTION
that permit self-diagnosis are covered below. Our trouble- itself. shooting algorithm begins with Power-Up and continues until Game Over Mode. All procedures can be performed with minimal tes! equipment or merely by observing the game
POWER-UP TESTS
NO GENERAL ILLUMINATION NO INITIAL VIDEO CHECKING POWER SUPPLY BOARD
- Check fuse F2 on power supply board.
- Check for proper installation of jumpers W1, W2, W3 and/or resistor R27. (Some machines MAY NOT have an R27. Refer to your drawing set.)
- Press reset button on CPU Board. {2) Try RAM and ROM Diagnostic-Mode tests (see below).
- If these tests don't turn up the problem, check power supply board.
- Swap power supply board with one from known-good game.
- !f game plays, problem is on power supply board.
- If game doesn't play, check power
- Check 4P4/4, 4P3/J3, 6P2/J2 and OP3/I3,
- if all the above don't turn up the problem, check power supply board. transformer with voltmeter.
- If known-good power supply is unavailable for tests above, check +5V and +12V outputs on power supply in game. Each MUST BE within 2% of rated output with less than 0.4% AC hum.
Diagnostics
TURN SWITCH 8 OF DIP SWITCH #2 TO THE ON POSI- TION and turn power ON. The diagnostic program consists of 8 independent tests, 2 of which are automatic at turning power ON in diagnostic mode: RAM Test and ROM Test. After these two tests have been properly completed, pressing the 2-Player button brings a menu of the other tests to the CRT display:
01 DIP SWITCH
02 1-0 PORT
03 SOUNDS
04 CHARACTER
O05 COLOR
O6 CROSS HATCH PATTERN
Figure 2. Diagnostic Menu
OPERATE THE JOYSTICK to position the cursor at the desired test. Press 1-Player Start to initiate the test.
AS ANY TEST OTHER THAN 02 IS COMPLETED, pressing the 2-Player button returns the test menu to the monitor display. When test 02 is completed, the joystick lever must be moved left while pressing the 2-Player button to return the test menu. If no further testing is desired, turn power OFF and return switch 8 of DIP switch #2 to the OFF position. RAM TEST IF OK, “RAM OK” APPEARS ON MONITOR. If not OK, this indication appears on the monitor (without ROM test results)...
RAM NG XXXX vw zZ Faulty RAM address RAM Input Data RAM Output Data
IF RAM IS SHOWN TO BE NG AT RAM ADDRESS E000- EFF, failure can have occurred in either 3B RAM or 2K decoder on M52-A CPU Board.
IF RAM IS NG AT ADDRESS 8000-9FFF failure is associated with RAMs on the M52-F scrolling video board. In addition to these RAMs (3K and 3M), chips ID, 4, 4M, AN, 3H, 35, or 3F on the scrolling video board on chip 5M on the CPU Board may cause this failure.
FAILED RAM ADDRESS RAM 8xOx - 8x3x 3K 9x0X - 9x3x 3K 8x4x - 8x7X 3M 9xAX - 9XTX 3M 8x8x - 8xBx 3K 9x8x - 9XBX 3K 8xCx - OXFX 3M 9XCX - OXFX 3M
ROM TEST If OK, the display below appears on the monitor. RAM OK ROM 0 OK FF ROM 4 OK FF ROM 2 OK FF ROM 3 OK FF x
I if any are bad, for example ROM 4, this appears on monitor... RAM OK ROM 0 OK FF ROM 4 NG FF ROM 2 OK FF ROM 3 OK FF6
A faulty ROM must be replaced to continue diagnostics.
Certain failure modes of ROMs 4 thru 3 on M52-A CPU Board and ROMs 3C and 3E on M52-F Scrolling Video Board prevent fault indications from appearing on the CRT.
M52-A CPU BOARD
*CRT locks up with random test pattern Remove ROMS 2 and 3 and repeat test. If test results
are now shown insert ROM 2 and ROM 3 one at a time
to determine faulty chip. If not replace ROM 4.
*ROM 4 no good—Replace 3L.
RAM OK ROM 0 NG ROM 1NG ROM 2 NG ROM 3 NG Replace 3K
RAM OK ROM 0 OK ROM 1 OK ROM 3 OK ROM 3 NG
M52-F SCROLLING VIDEO BOARD +After power up tests, arabic numbers are missing from CRT—Replace ROM 3C. +After power up tests, letters are missing from CRT— Replace ROM 3A or 3E. «Blue missing in color test—PROM 4F. +Red missing in color test—PROM 4H. Replace 3J
01 DIP SWITCH TEST Shows state of all switches contained in DIP switches #4 & #2 and the resulting game adjustments. With the monitor displaying the test menu, position the cursor at 01 and depress 1-Player Start.
DIPSW123 45 swi140010 sw20 1000 FUEL CONSUMPTION AT COLLISION ooo ooo
*MID FUEL CONSUMPTION IN RUNNING Low CONTINUITY YES SPEED M/h COIN MODE A 4 COIN 4PLAY BODY TYPE UPR *LOW=8 % HIGH = 15% MID=12% MAX= 18%
Troubleshooting
GAME ADJUSTMENTS CAN BE SET AND CHECKED using switches contained in DIP 1 and DIP 2. To make sure all switches are functioning properly, set switch 8 of DIP 2 to the ON position and select test 01 of the diagnostic test menu. The video display of test 04 shows the state of every switch in DIP 4 and DIP 2, and the current game adjustments. A “4"=ON, and “0"=OFF for all switches.
Switch functions listed below:
DIP SWITCH 4
Switch Function
1&2 Determine the percentage of fuel lost in a collision (8-18%). If these switches fail, measure resistance between pin 4 and pins 2 & 3 of RAS, or replace chip AR
3 Determines fuel consumption rate (low/high). For failure of this switch measure resistance between pin 1 and pin 4 of RAS, or replace chip 4F.
4 Continued play (yes/no). For failure of this switch measure resistance between pin 1 and pin 5 of RAS, or replace chip 41F.
5,6,7&8 Determine the pricing for colin modes 1 & 2. For failure of these switches, measure resistance between pin 4 and pins 6, 7, 8, & 9 of RA5, or replace chip 4E.
IF ALL SWITCHES OF DIP SWITCH 4 FAIL, first check voltage at pin 1 on RAS for Vcc, then check switches and associated chips and circuitry.
DIP SWITCH 2
1 Flips picture vertically when in the ON position to accomodate different monitors. Set it to OFF for all games. If the picture is flipped anyway, check pins 44, 12, & 13 of chip 6K; measure resistance between pins 1 & 2 of RA6, or replace chip 41H.
2 Defines the game type. Upright games require it to be ON and cocktail table games require it to be OFF. For failure of this switch, measure resistance between pins 1 and 3 of RA6, or replace chip 4H.
3 Determines coin mode 4 (OFF) or coin mode 2 (ON). Failure of this switch requires measurement of resistance from pin 1 to pin 4 of RA6, or replacement of chip 4H.
4 Distance Unit (mH/kmH). Failure of this switch requires measurement of resis-
tance from pin 4 to pin 5 of RA6, or replacement of chip 4H.
5 Allows seleciion of Freeze-Screen test feature. Freeze-Screen feature allows the 1-Player Start to sfart motion of the game and the 2-Player Start to stop motion of the game. Failure of this switch requires measurement of resistance from pin 4 to pin 6 of RA6, oF replacement of chip 4F.
é NOT USED—Must be off.
7 Permits “Demo” mode (allows viewing of entire courses in game play since no fuel is used). Failure of this switch requires measurement of resistance from pin 4 to pin 8 of RA6, or replacement of chip 4H.
8 Permits Diagnostics mode. Failure of this switch requires measuremeni of resistance from pin 4 to pin 9 of RA6, or replacement of chip 1H.
IF ALL SWITCHES OF DIP SWITCH 2 FAIL, first check voltage at pin 1 on RAG for Vcc, then check switches and associated chips and circuitry.
02 I-O PORT TEST CONTROL PANEL AND COIN DOOR SWITCHES.
Shows if all controls and coin mechanisms are functioning properly by displaying a matrix composed of the states of switches on the Control! Pane! and Coin Door. With the monitor displaying the test index, posltion the cursor at 02 and depress 4-PLAYER START.
42345678
| KEY | © | o0000000 |
| KEY | 4 | 00000000 |
| KEY | 2 | 00000000 |
TIMING 0000. The TIMING number starts at 0000 and adds one count approximately every second.
If any control panel or coin door switch is closed a “1” will appear in the above matrix as follows:
4-Player Start Button KEY 0-4 2-Player Start Button KEY 0-2 Coin Switch A KEY 0-4 PA Right KEY 41-4 P4 Left KEY 4-2 P4 THROTTLE KEY 1-6 P41 BRAKE KEY 4-8 P2 Right KEY 2-4 P2 Left KEY 2-2 Coin Switch B KEY 2-5 P2 THROTTLE KEY 2-6 P2 BRAKE KEY 2-8 COIN SWITCH B is present only in games with coin doors that accept coins of two different values. The P2 switches ore used in cocktail table games only. To end this test and return to test index, move joystick lever left while pressing the 2-Player Start Button.
Troubleshooting
ALL CONTROL PANEL AND COIN DOOR SWITCHES CAN BE CHECKED (see below) with diagnostics test 02. Also, the display includes a TIMING check which should advance about one count per second.
1-0 PORT LAYOUT
| i. | 1[2f3fa4at[s5]of7]|e | | |
vw | 22 . KEY O start | START ISERVICE*| COIN A
| Pl | PL | Pl | PL | ||
| kev 1 | RIGHT | LEFT | THROTTLE| | BRAKE | | |
| yen} | P2 | P2 | COINB | P2 | P2 |
| kev2 | RIGHT | LEFT | THROTTLE! | BRAKE |
TIMING 0000
- Service switch not provided. ** Player 2 switches on cocktail table games only.
PORT PULLUP RESISTOR CHIP
| KEY 0-4 | RA3-5 | 4E |
| KEY 0-2 | RA3-3 | 4E |
| KEY 0-3 | RA3-2 | 4E |
| KEY 0-4 | RA3-4 | 4E |
| KEY 1-4 | RA2-9 | 1D |
| KEY 1-2 | RA2-5 | 4D |
| KEY 1-6 | RA2-6 | 4D |
| KEY 1-8 | RA2-8 | 4D |
| KEY 2-4 | RA1-9 | 1c |
| KEY 2-2 | RAI-5 | 1c |
| KEY 2-5 | RAI-4 | 4c |
| KEY 2-6 | RA1-6 | 1c |
| KEY 2-8 | RAI-8 | 4c |
03 SOUNDS TEST
A list of sounds normally produced by the game appears as shown below on the monitor. With the monitor displaying the test menu, position the cursor at 03 and depress 1-Player Start. Position the cursor with the joystick to select a sound and press the 1- Player start button for repetition of the sound.
01 PHONE SOUND 02 BRAKE SOUND 03 SPINNING SOUND 04 PASSING SOUND 4 05 COUNTDOWN SOUND 06 ADD. FUEL SOUND 07 JUMPING SOUND. 08 COLLISION SOUND 09 OPENING MUSIC 40 ENDING MUSIC 44 ARRIVAL MUSIC 42 FINAL GOAL MUSIC 43° CHECKPOINT MUSIC 14 *BGM 4 STREET 45 *BGM 2 ROUGH WAY 46 *BGM 3 HIGHWAY 47, WARNING SOUND 48 PASSING SOUND 2
*BGM= Background Music
Troubleshooting
NO SOUND: ‘CHECK Sound Select Data Levels Sound Number D7* Dé D5 D4 D3 D2 D1 DO
| 4 | 4 | ie) | (e) | 0 | 0 | ie) | 0 | 4 |
| 2 | 4 | 0 | (e) | 4 | 0 | 4 | A | ie) |
| 3 | 1 | 0 | ie) | 4 | 0 | 4 | A | 4 |
| 4 | 4 | 0 | (e) | 4 | 4 | 0 | 0 | 4 |
| 5 | [4 | ie) | 0 | 4 | 0 | A | tt) | 4 |
| 6 | 4 | ie) | 0 | 4 | 9 | i) | 4 | 4 |
| 7 | 4 | 0 | () | 4 | tt) | 4 | 0 | 0 |
| 8 | 4 | 0 | 0 | 4 | 4 | 4A | 4 | A |
| 9 | 4 | 0 | 0 | 4 | 4 | A | 0 | 0 |
| 410 | A | 0 | 0 | 4 | 4 | 0 | 4 | 4 |
| “ | 4 | tt) | ie) | 4 | 4 | 4 | 0 | 4 |
| 12 | 4 | 0 | ie) | 4 | 4 | 4 | 4 | 0 |
| 13, | 4 | ie) | 0 | 4 | 4 | 0 | 4 | (e) |
| 14 | 4 | 0 | 0 | 4 | 4 | 0 | 0 | 0 |
| 15 | A | 0 | 4 | 0 | 0 | 0 | tt) | tt) |
| 16 | 4 | 0 | 4 | 0 | 0 | 0 | 0 | 4 |
| 7 | 4 | 0 | 0 | 4 | 0 | tt) | 4 | 0 |
| 18 | 4 | t) | t) | A | 0 | i) | ie) | 4 |
*Pulses Low For Each Sound
*Sounds 2 thru 7 and 47 and 18 not produced—Chip 41F faulty. +Any other sounds missing or duplicated—Chip 4J or 4F faulty.
REMEDY OR ADJUSTMENT
GND, +5V, +12V, and Speaker connections. Fix as needed.
Rotate Volume Control VR1 on Sound Board and listen for scratching sound in speaker. If none, chip 2M or associated circuit on Sound Board faulty.
Touch 3M-3 with one end of an unterminated test lead for speaker clicking sound, If none, chip 3M or associated circuit on Sound board faulty.
Check that chip 3D-3 remains low for 1 second after power up. If not chip 3D on associated circuit on Sound Board faulty.
CPU Board chip 1K-12 for low pulse each time 4- Player Start is pushed. If no pulse, disconnect Sound Board from CPU and recheck. If still not pulsing, chip 1K on CPU Board is faulty. If it now pulses, chips 4F or 3J on Sound Board faulty. If pulse present originally, replace plug-in chips on Sound Board one at a time.
Check that chip 3E-8 and -10 are low, and 3£-9 is high when 3D-3 goes high. (This powers up MPU 3E in proper mode.) If not 2K, associated capacitors, or 3E on Sound Board faulty.
Interchange socketed chips 3F and 3J. If some sounds are now produced the chip now in 3F socket is faulty.
Across each crystal for AC voltage. If none, crystal or associated capacitors faulty.
04 CHARACTER TEST
With the monitor displaying the test index, position the cursor at 03 and depress 1-Player Start. A display composed of eight numeral fours appears on monitor.
CIRCLES = YELLOW
4s=RED
SCREEN =BLACK
Character Test
Troubleshooting
Faults in chips on M-52-B-C Character Board result in symptoms as follows;
SYMPTOM CAUSE
Blank Screen 4F Blank Screen 2H 8 yellow squares with red fours 3N 8 tan squares enclosing red 3M circles with tan fours Eight light blue squares 3K enclosing dark blue circles with light blue numbers
05 COLOR TEST
Position the cursor at 05 and depress 4-Player Start. This test consists of 5 independent steps (advanced by depressing 1-Player Start) as follows:
- An alphanumeric display is shown as below over a tow of numbers 0 thru 9, letters blue and numbers white.
ABCDEFGHIJKLMNOPQRSTUVWXYZ
0123456789
- Acolor-pattern is displayed as shown.
- A field of red is displayed.
4.A field of green is displayed.
5.A field of blue is displayed.
Each independent step of this COLOR test can be advanced through by pressing the 4 Player start button. Color-Pattern Test
06 CROSS HATCH PATTERN TEST
Position the cursor at 06 and depress 4-Player Start. A white line matrx 15 lines vertical x 18 lines horizontal is displayed.
+5VDC Power Supply Adjustments
BEFORE ADJUSTING THE VOLTAGE OUTPUT, aiways check at the output of the supply for AC hum. This hum should never rise above .005V on the +5VDC supply. If it does, consult your schematic drawing set for proper DC voltages throughout the circuit.
TEST FOR THESE with the DC setting of your multimeter. Make a second check using the AC seiting. Pay particular attention to readings at TPS (top of capacitor C10). If the voltage here is low (less than +44VDC) or if you find excessive ripple (more than 700mVrms), replace the capacitor.
IF TP4 IS LESS THAN +4.95VDC remove R(40. If TP4 is still less than +4.95VDC, then check precision resistors R25 and R26. if they are within the 1% tolerance, then check IC2.
CHAPTER 4 Parts
31150-3024-U
03-7696-4
3I-NS1-3024-U
uaTch 20-9347} *
R-9893—
03-7688 T
20-8995
c-8994
20- 6542-TB,
6454
4320-01123-20\
_———— 5640-06137-00
01-7228 4420-01i41-00.
01-7485 4-733,
01-6994. \
4608-01081-07 \e Ti
a D-9894
03-7602,
FSS x Ka [Roe | A 01-7226 ~|
01-7446 "4608-O1081-Il 01-7735
24-6597-5 01-7479, "4003-01051-06 O-3827 -4008-01005-04 20-8746 20-8747 20-8748-1 5792-09395-00 §822-08841-00 SN Bee once coy ‘31~1069-3007-U -4108-01001-24 01-7446 -4608-01080-10 5792-09110-00 (S82i-09081 01-7267 H-8836 03-7655~4 '5565-09382-01
LUIGHT REFLECTOR Assy (D-9246)
NOTES:
| Weer ING. are ane 328