CATHODE RAY TOMES

Shuuz TM-358 Kit Instructions

Shuuz (version 8.0) (Atari Games, 1990) · Kit Instructions · 45 pages · 50 sections · original scan

Page 1

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 2

Conversion kit for upright and countertop games

Page 3

Copyright © 1990 by Atari Games Corporation. All rights reserved. No part of this publication may be reproduced by any mechanical, photographic or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher. The game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the U.S. Copyright Act of 1976. This Act provides for substantial penalties for violating federal copyright laws. Courts can Shuuz Universal Kit

RE. NOTICE

WARNING Use of non-Atari parts or modifications of any Atari game circuitry may adversely affect the safety of your game, and may cause injury to you and your players.

impound infringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles. In addition, the Act provides for payment of statutory damages of up to $50,000 per infringing transaction in certain cases. Infringers may also have to pay costs and attorneys’ fees and face an imprisonment of up to five years as well as fines of up to $250,000 in the case of individuals and up to $500,000 in the case of corporations. Atari Games Corporation will aggressively enforce its copyrights against infringers. We will use all legal means to immediately halt any manufacture, distribution, or operation of a copy of video games made by us, Anyone who purchases such copies risks forfeiting such a game.

Published by: Atari Games Corporation 675 Sycamore Drive P.O. Box 361110 Milpitas, California 95036 Printed in the U.S.A. 12/90 Produced by the Atari Games Technical Publications Department. Writing and Editing: Andrea Dencker Illustration and Design: Mary Ohanessian Sumner You may void the game warranty (printed on the inside back cover of this manual) if you do any of the following: ¢ Substitute non-Atari parts in the game.

  • Modify or alter any circuits in the game by using kits or parts not supplied by Atari Games Corporation.
NOTE This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of Federal Communications Commission (FCC) Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area or modification to this equipment is likely to cause interference, in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference. If you suspect interference from an Atari game at your location, check the following:
  • All ground wires in the game are properly connected as shown in the game wiring diagram.
  • The power cord is properly plugged into a grounded three-wire outlet.
  • On games provided with an Electromagnetic Interference (EMD ground cage, be sure that the game printed-circuit boards (PCBs) are properly installed on the EMI ground cage and that the end board is securely installed with all screws in place and tightened. If you are still unable to solve the interference problem, please contact Customer Service at Atari Games Corporation. See the inside front cover of this manual for service in your area.
Page 4

Shuuz Universal Kit

SUMMARY

The following safety precautions apply to all game operators and service personnel. Specific warnings and cautions wiil be found in this manual whenever they upply.

WARNING Properly Ground the Game. Players may receive an electrical shock if this game is not properly grounded! To avoid electrical shock, do not plug in the game until it has been inspected and properly grounded. This game should only be plugged into a grounded threewire outlet. If you have only a two-wire outlet, we recommend you hire a licensed electrician to install a three-wire grounded outlet. If the control panel is not properly grounded, players may receive an electrical shock! After servicing any part on the control panel, check that the grounding wire is firmly secured to the inside of the control panel. After you have checked this, lock up the game. AC Power Connection. Before you plug in the game, be sure that the game's power supply can accept the AC line voltage in your location. The line voitage requirements are listed in the first chapter of this manual. Disconnect Power During Repairs. To avoid electrical shock, disconnect the game from the AC power before removing or repairing any part of the game. If you remove or repair the video display, be very careful to avoid electrical shock. High voltages continue to exist even after power is disconnected in the display circuitry and the cathode-ray tube (CRT). Do not touch the internal parts of the display with your hands or with metal objects! Always discharge the high voltage from the CRT before servicing it. Do this after you disconnect it from the power source. First, attach one end of a large, well-insulated, 18-gauge jumper wire to ground. Then momentarily touch the free end of the grounded jumper wire to the CRT anode by sliding the wire under the anode cap. Wait two minutes and do this again. Use Only Atari Parts. To maintain the safety of your Atari game, use only Atari parts when you repair it. Using non-Atari parts or modifying the game circuitry may be dangerous, and could injure you and your players Handle the CRT With Care. If you drop the CRT and it breaks, it may implode! Shattered glass from the implosion can fly six feet or more. Use the Proper Fuses. To avoid electrical shock, use replacement fuses which are specified in the parts list for this game. Replacement fuses must match those replaced in fuse type, voltage rating, and current rating. In addition, the fuse cover must be in place during game operation.
CAUTION Properly Attach All Connectors. Make sure that the connectors on each printed circuit board (PCB) are properly plugged in. The connectors are keyed to fit only one way. If they do not slip on easily, do not force them. If you reverse a connector, it may damage your game and void your warranty. Ensure the Proper AC Line Frequency. Video games manufactured for operation on 60 Hz line power (used in the United States) must not be operated in countries with 50 Hz line power (used in Europe). If a 60 Hz machine operates on 50 Hz line power, the fluorescent line ballast transformer will overheat and cause a potential fire hazard. Check the product identification label on your machine for the line frequency required.

ABOUT NOTES, CAUTIONS, AND

WARNINGS In Atari publications, notes, cautions and warnings have the following meaning:

NOTE — A highlighted piece of information.
CAUTION — Equipment and/or parts can be damaged or destroyed if instructions are not followed. You will void the warranty on Atari printed-circuit boards, parts thereon, and video displays if equipment or parts are damaged or destroyed due to failure of following instructions.
WARNING — Players and/or technicians can be killed or injured if instructions are not followed.

iii

Page 5

CONTENTS

1 Set-Up How to Use This Manual ..... Cabinet Equipment Requirements . Tools Required. Inspecting the Kit Preparing the Cabinet for the Kit Installation . Assembling the Controi Panel.. Connecting the JAMMA Harnes: Installing the Shuuz Game PCB Installing the Bezel, Decals, Labels, and Attraction Assembly ..... Setting the Coin an Maximizing Earnings Game Play...

2 Self-Test Introduction .. ini Entering and Select Test Ment Statistics... Histograms.. Game Option: Coin Options. Sound Test. Controls Test...... Complete RAM Test. Complete ROM Te: Playfield Test..... Motion Object Test ObUdh ww

~~ . 1-10 1-10 1-10

DARUWER ROWM NW Shuuz Universal Kit

Color Test.. Color Purity Test Convergence Test 3 Maintenance and Troubleshooting Video Display Sync Problems Midi Trak-Ball Control. ROMs and RAMs...

4 Parts Mustrations

See the List of Illustrations that follows.

5 Schematic Diagrams See the List of Illustrations that follows.

Statistics Sheet

Page 6

Shuuz Universal Kit

ILLUSTRATIONS

Figure 1-1 Figure 1-2

Figure 1-3

Figure 2-1 Figure 2-2 igure Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure 2ti yy yy iy viv iy ty won . Installed Kit Parts... Front View of Cabinet-Mounted Assemblies (Dedicated Game)............ 1-4 Rear View of Cabinet-Mounted Assemblies (Dedicated Game)... 1-5

Self-Test Menu Screen... Statistics Screen Histogram Screen. Game Options Screen Coin Options Screen Sound Test Screen Controls Test Screen RAM Test Menu...... Complete ROM Test Screen Playfield Test Screen Motion Object Test Screen Color Test Scree: Purity Test Screen. Convergence Test Screen Figure 3-1

Figure 4-1 Figure 4-2 Figure 4-3

Figure 5-1

Figure 5-2

Figure 5-3

Table 1-1 Table 1-2 Table 1-3

Table 2-1 Table 2-2 Table 2-3 Table 2-4 Table 2-5 Table 2-6

Table 3-1 Table 3-2

Table 3-3 Table 3-4 Excessive Shaft Wear...

Parts for Shuuz Universal Ki Midi Trak-Ball Assembly .. Shuuz Game PCB Assembly

Shuuz Game PCB Assembly Schematic Diagram... Shuuz Coupler PCB Assembly Schematic Diagram... Faulty RAM/ROM Tables

TABLES

Equipment Requirements Contents of Shuuz Kit JAMMA Pin and Wire Connections...... 1-6

Summary of All Self-Test Screens Game Option Settings .. Coin Option Settings When to Run the RAM Tests Bad RAM Locations by Error Address. Bad ROM Locations by Error Address ..

Troubleshooting Table... Voltage Inputs and Test Points on the PCB. What ROM Problems Look Like Atari Games Video Connector Pin Assignments

Page 7

CHAPTER 1

Installation

How To UsE THis MANUAL

This manual provides information for installing, testing, and troubleshooting the Shuuz™ conversion kit. “ Chapter 1 describes how to install the Shuuz kit in your Dynamo or other cabinet. This kit can also be installed in coun-

tertop cabinets. This chapter also describes game play. Chapter 2 contains self-test procedures and additional diagnostic tests. The self-test is important in the Shuuz game. You can troubleshoot the PC boards, main circuits, and controls using the screens in the self-test. You should regularly test the boards and controls with the self-test to keep your game in peak condition and at top earnings. Gs oe

  • Chapter 3 contains contains troubleshooting and maintenance procedures for the Midi- Trak-Ball™ control. “ Chapter 4 contains the kit parts list and parts illustrations. ¢ Chapter 5 contains the schematics for the Shuuz game

PCB and the Trak-Ball Coupler PCB.

Page 8

Installation

WARNING To avoid electrical shock, unplug the cabinet while installing the kit. After installation, plug the game only into a grounded 3-wire outlet.

Cabinet Equipment Requirements Table 1-1 lists the equipment required in the cabinet into which you are installing the Shuuz kit.

CAUTION Do not unplug or plug in the Shuuz game printed-circuit board (PCB) edge connector while the power is on. You could seriously damage the PCB.

Tools Required ¢ Drill with a 1/2-inch and 5/16-inch drill bits ¢ Phillips screwdriver ¢ Flat-blade screwdriver ¢ Socket wrench set and ratchet ¢ 1/4-20 hex wrench © Wire cutters and strippers ° Straight edge Shuuz Universal Kit

Table 1-1 Equipment Requirements

Equipment Specification Video Display Color RGB monitor Separate positive horizontal and vertical sync or negative composite sync Horizontal mounting Horizontal frequency: 15.750 KHz Vertical frequency: 60 Hz Video input: 1V to 3V peak-to-peak positive polarity Control Panel Metal only Speaker 8Q, 10W Coin Counter +5 VDC or +12 VDC Power Cord Three-conductor with ground Power Supply +5 VDC + 0.25V @ 3.0 amps +12 VDC @ 1.0 amp -5 VDC @ 1.0 amp

  • Squeegee ° X-ACTO™ knife ¢ Insulated wire connectors (if you are installing a new JAMMA harness) © Carbon paper ° Saber saw ° File
  • Bandsaw
  • Tape or glue

Table 1-2 Contents of Shuuz Kit

DescriptionPart No.Description
+6 x 3/4°-Long, Type AB, Pan-Head,175014-1040+10 Flat Washers (8)
Cross-Recessed Screws (4)177010-240#10-24 Hex. Polymer Locknuts (8)
=10-24 x 3/4"-Long Black Carriage Bolts (4)178032-002=10 Wire & Cable Tie
7=10 x 3"-Long Black Carriage Bolts (4)178237-006Green Button Assemblies (2)

038158-01 Product [.D. Label 178265-001 L-Style Nylon Standoffs (4)

039450-01FCC Compliance Label178283-008Indicator Plates (Start/Action), Black with
047205-01Shield. AttractionWhite Back (2)
047209-01Control Panel CoverA038038-01Midi Trak-Ball Assy.
047991-01Control Panel DecalA046501-01JAMMA Harness Assy.
047992-01Side Panel Decals (2)A047365-01Shuuz PCB Assy.
047993-01Attraction Panel FilmA047982-01Trak-Ball Adapter Harness Assy.
047994-01Monitor Bezel with GraphicsTM-358Shuuz Universal Kit Installation
048431-01Instructions Label for Countertop GamesInstructions

£1091 09, DE ‘ . .

tantoSorption, hee Oo te Split Beads (2)Packaging materials are not listed. All parts are a quantity

of 1, except as noted in parentheses.

Page 9

Shuuz Universal Kit Installation

NOTE Your game cabinet may not appear exactly as shown in this illustration, The picture shows the control panel and electronic parts installed in a typical game cabinet.

040431-01 1 Instractons Labe! ‘Yor Counterop ‘Games Only)

‘Side Panel Decal

‘AOATS65-01 7551488 . : ‘Shuuz PCB Assy. 4830 x30" Carnage Bo '78265-001 x (places) Style Nylon Standott (3 places}

{4 places) 175014-1040 #10 Flat Washer (4 places) ‘Cross-Rec. Type-AB Screw (places)

Volume Gontrot Salt-Test Switch

178237006 | ‘Green Button Assy, | (2 places) 160044-001 | ‘Snap-Action Switch "2 places) 178283-008 | Indicator Plate 1 ISTARTACTION) | ‘2 places) | "a030038-01 Miat Trak-Ball Assy, ‘A0S7982-01 ‘Trak-Ball Adapter Hamess Ass

Figure 1-1 Installed Kit Parts

Inspecting the Kit Preparing the Cabinet for

Check to see that you have all the parts listed in the the Kit Installation kit parts list in Table 1-2. If any part is missing or damaged, contact your distributor with the Shuuz kit serial number, part number. and description of the missing WARNING or damaged parts. and date received. To avoid electrical shock, unplug the cabinet while installing the kit. After installation, plug the game only into a grounded 3-wire outlet.

1-3

Page 10

Installation

Lower Ratainar | 046926.01 | Upper Retainer

04757301 | tack Bezel

03799402 | Bezel With Graphics | 178056-002 SW. x 116" | ‘Thk Foam Tape

046927-01 | Video Display ‘Shield

+78263-080' 12" Sik Foam Tape | 178263-1202 ‘14° Bik Foam Tape :

75-3816 | 1#8-32 C’sunk som 75514881 #10x3.0"| Cartage Bolt! +78013-001 | (4 places) Draw Latch [ 17010-2401 810-24 Polymer Hex. Locknut (4 places) | 75014-1040 Shuuz Universal Kit

Fluorescent Lamp Fixture

047992-01 Sida Pane! Decal

75-07002 Flat Washer 75.9515 174-20 Nov ‘Washar Assy. Ag47441-01 AMMA Power ‘Supply Assy.

X-Rec, AB Type Screw (4 places)

10 Flat Washer | (4 places) |

Grean Button Assy. | (2 places) |

(2places) eee

(START/ACTION) |

~iaee om aS ape i han Controt Panel Assy. ph oot A04848s-01 ‘Control Panel Harness. 7551168 10-24 Carriage Bott 75-0408 #10 Split-Lock Washer 17014-1040 #10 Flat Washer 17000-1490 10-24 Hex Nut Volume Controt Sel-Tast Switch

gost Coin Counter

99-15109 Cash Box

171093-001 Coin Door Assy.

Figure 1-2 Front View of Cabinet-Mounted Assemblies (Dedicated Game)

1-4

Page 11

Shuuz Universai Kit Installation

Items Not Shown:

TM.296 Video Display Service Manual A047607-01 Video Harness Assy. A047603-02 Video Power Harness Assy.

047574.01 Back-up Board A047073-01 Main Wiring Hames contel Hames ADEE Y Power Switch Assy. 178056-002 ‘/2-Inch Foam Tape 175008-002 Nylon Washer 046926-01 Upper Retainer 009992-01 On/O#f Switch Enclosure

TM.358 Shuuz Universal Kit ‘nstallation instructions

047992.01 Side Panel Decal |

NOTE These two pages show the dedicated game version of Shuuz that was sold in very | limited quantities.

Rear Door 178255-004 | Adjustable Glide

178093-001 Fan Guard i 176019-212 #8 Sq-Dr. Screw

Figure 1-3 Rear View of Cabinet-Mounted Assemblies (Dedicated Game)

Page 12

Installation, Shuuz Universal Kit

Table 1-3 JAMMA Pin and Wire Connections

Wire Pin Color __ Signal Instructions Component Side

1BNGNDConnect to the 5V RTN (GND) terminal on the power supply. However, if you have 12V

RTN, connect ove of the BN wires at pin 1, 2, A, or B to the 12V RTN terminal.

2BNGNDSame as pin 1.
3R+5VConnect to the +5V terminal on the power supply. However, if your power supply has a

+SENSE terminal, connect one of the R wires at pin 3, 4, or C to +SENSE instead of +5V.

4R+5VSame as pin 3.
5OR-5VConnect to the —5V terminal of the power supply.
6Y+12VConnect to the +12V terminal of the power supply.

If your coin counter(s) require 12V, also connect to the + side of the coin counter(s). 7 Key

8BU/WCOIN CTR1Connect this wire to the ~ side of the coin counter. Note: Do not use 24V counters.

Connect the + side to +5V or +12V on the power supply, as appropriate. 9 Not used

10BNSPKR +Connect to the + terminal on the speaker. (This wire is part of a twisted pair.)

i Not used

12RREDAttach to the video display.
13,BUBLUEAttach to the video display.
14BKVIDEO GNDAttach to the video display.
15WwSELF-TESTUse this wire if you want an external self-test switch. However, the kit already has a self-

test switch on the PCB. (If you connect an external self-test switch, switch off the switch on the PCB. Connect the wire to the N.O. terminal on the external self-test switch. Connect the common terminal of the switch to a BK/W wire (GND).)

16BgLT COINConnect to the N.O. terminal of the left coin switch. Connect the common terminal of the

switch to a BK/W wire. 17 W/BK — Not Used

18W/BNTB X DIR
19W/RTB Y DIR
20W/ORTB XCLK
21WYTB Y CLK
22W/GNRT BUTTON
23W/BULT BUTTON
24W/VNot used
25W/GYNot used

26 Not used

27BK/WGNDConnect one of the BK/W wires at pin 27, 28, e, and f to the negative sense terminal of

the power supply (if it exists) and one to the common terminals of the coin switches. Connect two of these wires to the common terminals of the control switches on the control panel.

28BKE/WGNDSame as pin 27.

Connect the matching colors on the Trak-Ball adapter harness.

Figure 1-1 shows almost all kit parts installed in a typical cabinet. Use this illustration as a guide while you install the parts. For your ordering convenience. Figures 1-2 and 1-3 show most of the parts in the Shuuz game (dedicated game version).

  • Turn off power to the game, and unplug the power cord.

1-6

  • Remove the following from the cabinet: Existing PCBs Game harness, if it is not Japan Amusement Machinery Manufacturers Association (JAMMA)— compatible Control panel decals, labels, and controls
Page 13

shuuz Universal Kit Installation

Table 1-3 JAMMA Wire Connections, Continued

Wire

Pin Color Signal Instructions

Solder Side

ABNGNDConnect to the 5V RTN (GND) terminal on the power supply. However, if you have 12V

RTN, connect one of the BN wires at pin 1, 2, A, or B to the 12V RTN terminal.

BBNGNDSame as pin A.
cR+5VConnect to the +5V terminal on the power supply. However, if your power supply has a

+SENSE terminal. connect one of the R wires at pin 3, 4, or C to +SENSE instead of +5V.

DR+5VConnect to the R wire on the Trak-Ball adapter harness.
EOR-5VConnect to the -5V terminal of the power supply.
FY+12VConnect to the +12V terminal of the power supply.

H Key

JVwCOIN CTR 2Connect this wire to the - side of the second coin counter. Clip R28 on the game PCB if

you use a second coin counter. Note: Do not use 24V counters. Connect the + side to +5V or +12V on the power supply, as appropriate. K Not used.

iLWwSPKR-Connect to the - terminal on the speaker. (This wire is one of a twisted pair.)

M Not used

|NGNGREENAttach to the video display.
PBNCOMPSYNCAttach to the video display.
RGYService

s Not used

TORRT COINConnect to the N.O. terminal of the right coin switch. Connect the common terminal of

the switch to a BK/W wire.

UY/BKNot used
VvY/BNNot used
WwY/RNot used
xY/ORNot used
Yy/wNot used
ZzY/GNNot used
aY/BUNot used
ibY/VNot used
leY/GYNot used
dGY/WNot used
eBK/WGNDConnect one of the BK/W wires at pin 27, 28, e, or f to the negative sense terminal of the

power supply (if it exists) and one to the common terminals of the coin switches. Connect two of these wires to the common terminals of the control switches on the control panel and the BK wire on the Trak-Ball adapter harness.

fBK/WGNDSame as pin e.

¢ Side decals, graphics, and adhesive. If the cabi- 7

net sides are damaged, repair them before put- Assembling the Control Panel

ting on the new decals.

  • Video display shield, display bezel. attraction NOTE shield, and marquee. This kit includes a Midi-Trak Ball control
  • Wipe down and vacuum the cabinet. Paint the cab- that will fit most upright games. If you are inet, if required. installing this Shuuz kit into a countertop cabinet, you should purchase a small Mini Trak-Ball from your Atari Games distributor (Atari part no. AO36190-01).
Page 14

Installation

Parts Needed To assemble the control panel, you need a copy of the appropriate control panel hole-cutting template. Two versions of the template (for countertop and upright games) are printed at the center of this manual. Gently pull out the template sheets from the staples, and the manual should remain bound. You will also need the following parts from kit:

  • Clear cover for the control panel
  • Control panel decal
  • Two green button assemblies
  • Two snap-action switches
  • Two indicator plates (Start/Action)
  • One Midi Trak-Ball
  • Four =10 x 3"-long black carriage bolts, flat washers, and locknuts
  • Four #10 x 3/4"-long black carriage bolts, flat washers, and locknuts

Installing The Parts

  • Using carbon paper, wansfer the Trak-Ball mounting pattern from the template to the control panel. Be sure to center the Trak-Ball control on the panel for best playability. Save the template. vv Drill four 5/16" holes for the Trak-Ball mounting bolts.
  • Using a saber saw, carefully cut out the large hole “A” for the Trak-Ball. Deburr the sharp edges with a file.
  • Lay the plexiglass cover over the top of the control panel and mark the outside shape of the panel on the plastic. Also mark the two button holes “C” as close as possible to the locations shown on the template. Lastly, mark the positions of the four holes which mount the cover to the control panel. Using a bandsaw, cut the control panel cover to its correct outside shape. wa Shuuz Universal Kit
  • To prevent injury, carefully deburr all the edges of the plexiglas cover.
  • Install the controi panel decal on the control panel. Use a sharp X-ACTO knife to trim the outside edge and to cut out the holes for the controls.
  • Install the cover on the control panel with the four 3/4"-long carriage bolts, washers, and locknuts.
  • Install the midi Trak-Ball assembly using the four 3"-long carriage bolts. Install the two button assemblies and the indicator plates.
NOTE The orientation of the Trak-Ball is critical. Refer to the template for a picture of the correct position.

For maintenance and servicing information on the Midi Trak-Ball control, refer to Chapter 3 of this manual.

Connecting the JAMMA

Harness

  • If your game cabinet does not already have a JAM- MA harness, install the JAMMA harness in the cabinet.. Install the split beads on the harness as close to the PCB edge connector as possible. Hold the beads on the harness with the tie wraps included in the kit. n
CAUTION You must install the split beads included in the kit on the JAMMA harness to meet FCC requirements.
  • Using Table 1-2 for wiring information, connect the JAMMA harness to existing component harnesses. Use crimp splices or butt soldering.
WARNING Wear safety glasses when drilling the plastic contro! panel cover. Use care to avoid shattering or chipping the plastic.

6, Tape or glue the template to the plexiglass cover. To start the saber saw cut, drill a 1/2" hole inside the “B” and each “C” hole.

  • Saw out the large hole “B” and both “C” holes. Drill the four 5/16" holes that will be used to mount the cover to the control panel. ea

1-8

WARNING Do not simply tie the wires together. If you do, you could cause intermittent problems, loose connections, oxidation, or a fire.

Connecting Power Wires

  • Connect the wires on the JAMMA harness to the wires for the power supply, as shown in Table 1-3. The Shuuz kit requires +5V and +12V. If -5V is available, it should be used too. Tie off any other
Page 15

Shuuz Universal Kit

voltage wires on the power supply besides +5V, —5V, and +12V. There is more than one wire for each voltage in the JAMMA harness. Use more than one wire for each voltage (connecting them as described in Table 1-3) so that the edge connector does not overload and burn.

Connecting Video Display Wires

NOTE The JAMMA harness provides only negative composite sync. If your video display requires separate positive sync, see Chapter 3 for alternative wiring.

Connect the wires designated for the red, green and blue video guns along with the syne and ground wires, according to Table 1-3.

Connecting Coin Door Wires

  • Connect the wires on the JAMMA harness to the coin switches and meter according to Table 1-3. wv Connect one terminal of the door lamps to one of the BK/W wires. Connect the other terminal of the door lamps to the R wire supplying +5V.
NOTE Do not use -5V for the coin door lamps. -5V is required for audio.

(Some games have separate power supply outputs for the coin door lamps. If you choose to use these outputs, make sure you connect both terminals of each lamp to the terminals on the power supply.)

Connecting the Control Wires

Connect the Trak-Ball adapter harness to the JAMMA harness using crimp splices or butt soldering, according to the information in Table 1-3. Then plug the adapter harness into the Trak-Ball harness.

Grounding the Cabinet Find the ground lead (green) of the 115V input power line. Connect this lead in daisy-chain fashion to a bare metal part of the coin door, the control panel, the video display, and the power supply. This AC ground must be of #18 AWG wire or larger.

WARNING For the safety of players, you must connect the green ground wire as indicated above. Installation

Checking the JAMMA Connections Before plugging in the game PCB, turn on the power to the game, and check +5 Volts on pins 3, 4, C, and D of the JAMMA connector; +12 Volts on pins F and 6; and —5 Volts on pins E and 5. Check that the video display and the attraction lamp have power. Now turn off the power to the game.

Installing the Shuuz Game

PCB

  • After you have checked the power on the JAMMA connector, above, install the Shuuz game board set in the cabinet. Use the nylon standoffs and four =6-32 screws in the kit.
  • Connect the JAMMA connector to the PCB.
  • Secure the JAMMA harness away from the PCB with cable ties.
  • Turn on the power to the game. Check that the game PCB functions. If a video picture is not present, see Chapter 3.

Installing the Bezel, Decals, Labels, and Attraction Assembly

The kit parts are shown assembled in a cabinet in Figure 1-1.

Installing the Display Bezel

Find the cardboard display bezel in the kit. This bezel can accommodate both 19-inch and 25-inch video displays. Follow the instructions on the back of the bezel, and cut the hole and outside edges as required.

Installing the Product ID and FCC Label Place the product ID label (part no. 038158-01) and FCC label (part no. 039450-01) on the back of the cabinet.

Installing the Side Panel Decals

Find the side panel decals. Wet the left and right side panels of the cabinet with slightly soapy water. Then position the decals as shown in Figure 1-1. Remove any wrinkles in the artwork using a squeegee. Allow the sides to dry.

Installing the Attraction Assembly Find the Shuuz attraction shield and the attraction film. Using the existing shield as a template, cut the shield and film to size, if necessary. Install them on the cabinet as shown in Figure 1-1.

1-9

Page 16

Installation

Setting the Coin and Game Options

Set the coin and game options in the self-test. See Chapter 2 for information about the option settings.

Maximizing Earnings

For maximum earnings, regularly maintain your Shuuz game following the instructions in Table 3-1, in Chapter 3, When you set up the game and when you collect money, perform the automated self-test and check the controls with the Control Inputs screen in the self-test.

Game Play

This section describes the features and play of the Shuuz game.

Introduction Shuuz™ is a video version of traditional horseshoes. The rules are similar to those used at picnics throughout America. In addition, an occasional round is designated a “beer round”. The player who loses that round is encouraged to buy a round of drinks for his opponents.

Each player inserts a coin. The players must select the game they want (one player alone or against the computer, two or three players head-to-head, or four players on two teams). Each player selects a character. Play continues in rounds until:

* A player trying the high score challenge uses up

his allotted rounds. ¢ A player or team has reached the specified final score. ¢ The players have used up their allotted rounds without scoring enough points. They will be of-

1-10 Shuuz Universal Kit

fered a chance to add a coin and continue with more rounds. In each round, all players in curn are allowed two tosses. After each round (or, in a team game, each halfround) the tosses are scored.

Scoring Ringer: 3 points. Close (within the circle): 1 point. If two opponents score ringers, the two shoes “cancel” each other and are ignored. Only shoes closer to the pin than any of the opponents’ shoes (ignoring canceled ringers) count toward your score.

Throwing a Shoe First, the player aligns his character by moving side to side with the track-ball. Pressing the button or exceeding a time limit ends this phase. Next, the player draws the shoe back by rolling the track-ball towards himself. The “arc meter” on the right side of the screen indicates the amount he is moving his character's arm. This controls the height of the trajectory that the shoe will follow. This phase oO ends after a time limit or when the player begins to roll the track-ball forward. Finally, the player rolls the track-ball forward. The speed and direction he spins the trackball controls the power and rotation of the throw. While the shoe is in the air, further movement of the track-ball adds “English”, allowing the shoe to curve right or left and to speed up or slow down its rotation.

Statistics

At the end of a game, the player is shown the number of ringers, the number of double-ringers, and the percentage of ringers for that game. In a high-score challenge, the player is entered on a high-score table if his total score is high enough. In head-to-head game play, a player can enter a high score if his ringer percentage is high enough.

Page 17

CHAPTER 2

Self-Test

INTRODUCTION

Use the Shuuz self-test to check each time you collect the monthe condition of the game cir- ey, or when you suspect game

cuitry and controls. You will see failure. “ This chapter shows the self-test information on the the screens in the self-test and

video display and hear the explains each of the tests. The sound test information through the speakers. screens and explanations are arranged in the You do not need any additional equipment to order they appear in the self-test. Table 2-1 perform the self-test. * You should perform lists all of the self-test screens and their the self-test when you first set up the game, purposes.

Page 18

Self-Test Shuuz Universal Kit

Entering and Exiting

the Self-Test

To enter the self-test, turn on the self-test switch on the game PCB. Exit the self-test by switching off the self-test switch. SELECT TEST

Then Press Left Button: STATISTICS GAME OPTIONS. COIN OPTIONS SOUND TEST CONTROLS TEST COMPLETE RAM TEST

Select Test Menu

Choose which test or screen you want to see from this menu, shown in Figure 2-1. Move up and down the list by rolling the Trak-Ball; the corresponding test is highlighted in white. Choose the screen by pressing COMPLETE ROM TEST PLAYFIELD TEST. MOTION OBJECT TEST. COLOR TEST PURITY TEST the left button.

Statistics

Use the information shown on the statistics screen, in CONVERGENCE TEST: Version 8.0° Fri Nove2°12:03:22:'1990'

Figure 2-1 Self-Test Menu Screen Figure 2-2. and on the histogram screens to keep track

Table 2-1 Summary of All Self-Test Screens

Screen Use or Purpose Statistics Screen Histogram Screen 1 Histogram Screen 2 Histogram Screen 3 Histogram Screen 4 Histogram Screen 5

Game Options Screen Coin Options Screen Sound Test Screen | Controls Test Screen

RAM Test Screen Video RAM (looping) Color RAM (looping) All RAM (looping)

ROM Test Screen Playfield Test Screen Motion Object Screen Color Test Screen

Purity Test Screen Red Color Purity Screen Green Color Purity Screen Blue Color Purity Screen White Color Purity Screen Grey Color Purity Screen

White Convergence Screen Violet Convergence Screen Green Convergence Screen Displays the histogram for all new games. Displays the histogram for ail continued games. Displays the histogram for scores per 10 rounds. Displays the histogram for “ringers” per 10 rounds. Displays the histogram for player characters chosen:

Use to set and check the game options settings. Use to set and check the coin options settings. Use to check the audio circuits. Use to test the player controls.

Use to check the video RAM. Use to check the color RAM. Use to check all RAM.

Use to check the program ROMs. Use to check the alphanumeric displays. Use to test the movement and color of game objects. Use to check the video display color circuits.

Use to check the red color purity in the video display. Use to check the green color purity in the video display. Use to check the blue color purity in the video display. Use to check the white color in the video display. Use to check the grey color in the video display.

Use to check and adjust video display convergence of red, blue, and green. Use to check and adjust video display convergence of red to blue. Use to check and adjust video display convergence of red and blue to green.

p re

Page 19

Shuuz Universal Kit

of your game use and maximize your protits. Record the information on the Shuuz statistics page in the back of this manual. The statistics are collected from the kast time the statistics were cleared. You can clear the statisues by holding down the right button and pressing the left button at the same time. Press the left Dutton to leave this screen and go to the histograms.

  • ¢ejt Coins show the number of coins counted in the left coin mechanism.
  • Right Coins show the number of coins counted in the right coin mechanism.
  • Idle Mins shows the number of minutes the game was not being played.
  • -lctive Mins is the number of minutes the game was being played in any mode.
  • 1 Player/2 Playery3 Player Games is the number of minutes the game was played by one. two. or three players.
  • 4 Player Games is the number of minutes the game «ved by four players on two teams. hw Plyr Avg Time is the average number of minutes the game was played by the 1,
  • 3. or 4 players
  • Error Count shows the number of errors counted in the erasable memory. If you have an error count, the statistics may be wrong. If you consistently have errors counted for several weeks. replace the EEROM at 38F.
  • Total Coins is the number of coins put into both coin mechanisms.

Figure 2-2 Statistics Screen Self-Test

  • dug Time/Coin is the average number of seconds played per coin.
  • Percentage Play is the amount of time, as a percentage, that the game is played while it is powered on.

Histograms

The five histogram (horizontal bar graph) screens show the length of game play and the number of games played. The first histogram screen is shown in Figure 2-3. Clear all five histograms by going to the last screen: then hold the right button down and press the left button.

Figure 2-3 Histogram Screen

Read the histogram screens frequently and record the numbers on the statistics sheet at the back of the manual. Read and then clear the screens frequently. If more than 255 games are played in any one time category, then all the numbers on that screen are divided by two. If you read the screens infrequently, the number of games will always be correct proportionally, but may be incorrect numerically. The five histogram screens show the following information:

  • New Games shows the number of seconds each new game lasted.
  • Continuations shows the number of seconds each continuation of the game lasted.
  • Score per 10 Rounds shows what scores were achieved for every 10 rounds’ worth of game play.
Page 20

Self-Test Shuuz Universal Kit

Table 2-2 Game Option Settings

Game Length, 1/2/3 Player 11, 13, 15, 17, 19, 21, 23, 25

Game Length, Team 13, 15, 17, 21, 25, 30, 35, 40

Initial Rounds Per Game 3. 4, 5, 6 7, 8,9, 10

Discount to Continue?YesNo

Frequency of Beer Round = Never Every 5 (rounds) ' Every 8 (rounds) i Every 10 (rounds)

| Sound in Attract ModeofOn
Auto-reset High ScoresOffOn

Option Settings Explanation

| Restore Factory OptionsYes.NoLets you set all the game options to the factory options or

| lets you use your own settings. Make sure you set this to | no to use your own chosen settings.

| Clear High ScoresYesNoLets you clear the high score table.

Manufacturer's recommended settings are in bold italic type. Lets you choose the maximum number of points each player can receive in 1-, 2-, or 3-player games. Lets you choose the maximum number of points each team. can receive in 4-player, 2-team games. Lets you choose the maximum number of rounds a player is given at the start of a game. Lets you offer a reduced price per credit when players want to continue a game.

Lets you choose how often the “beer round” message is displayed on the screen.

Lets you turn the sounds on or off in the attract mode.

Automatically resets the high scores to the factory defaults after 2000 games, unless a player has entered his initials within the previous 200 games.

  • Ringers per 10 Rounds shows how many horseshoe “ringers” occurred for every 10 rounds’ worth of game play.
  • Character choice shows how often the four player characters (Joe, Al, Sid, and Lefty) were chosen.

Game Options

Check and select the coin options on this screen, shown in Figure 2-4. To move through the options, roll the Trak-Ball up or down. Change the option in yellow type. The factory default settings are shown with a band behind them. To change a setting, roll the Trak-Ball right or left. To save the new settings, press the left button. This returns you to the select test screen. If you want to keep the original setting, although you have changed it, press the right button. This brings back the original setting. Use the left button to exit.

NOTE The word More appears at the bottom of the screen to indicate more options. Roll the Trak-Ball downwards to see the rest of the options.

Restore Factory Options? No Clear High Scores n GAME LENGTH: 1/2/3 player 15 pts GAMELENGTH: team 2tpts initiat Rounds per game

Discount to continue? No.

  • MORE o@ Pressing Right Button restores original setting Press Left Button: to save this setting and exit

Figure 2-4 Game Options Screen

The game option settings with factory defaults are shown in Table 2-2.

Coin Options

Check and select the coin options on this screen, shown in Figure 2-5.

Page 21

Shuuz Universal Kit Self-Test

Table 2-3 Coin Option Settings

Option Settings Explanation

Free Play No Yes Set this to “Yes” for demonstrating the game. | Game Cost I coin 1 credit Sets the number of coins required for one credit.

Right Mech Value

Left Mech Value Bonus for Quantity Buy-in 2 coins | credit

8 coins 1 credit

None 2 coins give 1 (extra coin) 3 coins give 1 (extra coin) 3 coins give 2 (extra coins) 4 coins give 1 (extra coin) 4 coins give 2 (extra coins) 4 coins give 3 (extra coins) 5 coins give 1 (extra coin) 5 coins give 2 ¢extra coins) 5 coins give 3 (extra coins) 6 coins give 1 (extra coin) 6 coins give 2 (extra coins) 6 coins give 3 (extra coins) 7 coins give 1 (extra coin) 7 coins give 2 (extra coins) 7 coins give 3 (extra coins) 8 coins give 1 (extra coin) 8 coins give 2 (extra coins) 8 coins give 3 (extra coins) 9 coins give 1 (extra coin) 9 coins give 2 (extra coins) 9 coins give 3 (extra coins)

1 coin counts as I coin

8 coins count as 1 coin

I coin counts as 1 coin

8 coins count as 1 coin

Manufacturer's recommended settings are in bold italic type. Lets you choose various levels of bonus coins or no bonus.

Is the number of coins each coin counts as in the right coin mechanism.

Is the number of coins each coin counts as in the left coin mechanism

Figure 2-5 Coin Options Screen To move through the options, roll the Trak-Ball up or down. Change the option in yellow type. The factory default settings are shown with a band behind them. To change a setting, roll the Trak-Ball right or left. To save the new settings, press the left button. This returns you to the select test screen. If you want to keep the original setting, although you have changed it, press the right button. This brings back the original setting. Use the left button to exit.

The coin option settings and factory defaults are explained in Table 2-3.

Sound Test

The sound test indicates the condition of the sound effects circuit on the game PCB. The sound test screen appears in Figure 2-6,

i» &

Page 22

Self-Test

Figure 2-6 Sound Test Screen

Use the Trak-Ball to select the sound and press the right button to listen to it. Pressing the left button returns you to the select test menu

Controls Test

The controls test screen is shown in Figure 2-7. Test the coin mechanism switches, control panel buttons, and Trak-Balls. As you use the control, the control name appears in red on the screen. If the name does not change to red, check the connections, switches, and mechanism. Simuitaneously press the left and right button to return to the test select screen.

Moving the Trak-Ball causes the yellow hexadecimal numbers to change when you roll it up and down (UP/DN) or left and right (LT/RT). If the numbers do not change, check the optical coupler PCBs, connectors. and harnesses for that direction of movement.

Controls: Test

Press Biittans And Move Trackball:

Left Panel Buttor Right Panel: Bution

Left Coin: Switch: Right Coin Switch

LETAi:. RAW SQUARE: UP/DN® 3C: 00: LURT 82. aa.

Press:Leftand Right Buttons: To Returnto men:

Figure 2-7 Controls Test Screen Shuuz Universal Kit

Complete RAM Test

Use this selection screen, shown in Figure 2-8, to choose which RAM test you want to perform. Use the different tests according to Table 2-4. If you get an error in any of the RAM tests. see Table 2-5 for more information. If you have serious RAM problems, you may see only a colored screen. Press the left button to leave the individual RAM tests and return to the RAM test menu screen. Press the left button once more to return to the test select screen.

Table 2-4 When to Run the RAM Tests

Location of

Problem‘Type of Test__RAMs Tested
Playfield is erratic orVideo RAM41N, 70N

looks wrong, or motion objects are not working properly.

Colors look wrong.Color RAM54K

Table 2-5 Bad RAM Locations by Error Address

Error RAM Location

AddressHighLow
3F000041NJON
3F400054K54K

RAM TEST

Video: RAM {looping} Color: RAM (looping) AIT RAM (re-start) Exit RAM tests

To-stop the test Hold the RIGHT button

To select; roll trackball up or down ‘Ther:press Left Button:

Figure 2-8 RAM Test Menu

Page 23

Shuuz Universal Kit

Complete ROM Test

The ROM test screen is shown in Figure 2-9. The 0K information appears. If the game has no ROM errors. you see the message ALL ROMS are OK. If the game does have ROM errors, the ROM test sereen will remain until the ROM error information is complete. Press the left button several times to pass the ROM errors. The ROM error test takes a few seconds, See Table 2-6 for the locations of the ROM errors. Press the left button to return to the test select screen.

Table 2-6 Bad ROM Locations by Error Address

ROM Location Error Address OK ” 23P

Figure 2-9 Complete ROM Test Screen

Playfield Test

‘This test. shown in Figure 2-10. checks the condition of the alphanumerics in the game. You can flip the characters into a mirror image of themselves by pressing the right button. ff you see an error on the screen. check the EPROMs at 87X. O5X. 43X. and 20X. Press the left button to go to the test select screen. Self-Test

Figure 2-10 Playfield Test Screen

Motion Object Test

The motion object test screen, shown in Figure 2-11, tests the movement and color of various game objects. Choose an object with the left button. Use the Trak- Ball to move the object. If there is an error, check the EPROMs AT 87W, 65W, 43W, 20W, 87U, 65U, 43U, and 20U. Press the left button to move to the next object. Simultaneously press the left and right buttons to go to the test select screen.

Color Test

This test indicates the dynamic range of the video display color circuit. The screen is shown in Figure 2-12.

Figure 2-11 Motion Object Test Screen

Page 24

Self-Test

Figure 2-12 Color Test Screen

The left side of the screen should be white, with a grey scale changing to white in the middle. The right half of the screen should be red, green, and blue from top to bottom. each with a color scale from dark to bright, left to right. If the screen does not match this description, adjust the video display as described in the video display manual. Return to the test select screen by pressing the left button.

Color Purity Test

The color purity test has five screens. Each screen is a rectangle of color. The first screen, shown in Figure 2-13, is red. The other screens, which you can see by pressing the right button. are green. blue, white, and gray.

Figure 2-13 Purity Test Screen Shuuz Universal Kit

These screens show the adjustment of the color purity of the video display. Each screen should display a rectangle of color, with no curving at the corners, no unevenness of color, and no lines in the display. If the screens are not correct, adjust the video display as described in the video display manual. Return to the test select screen by pressing the left button.

Convergence Test

The convergence test has three screens: first white, then violet, and finally green. The white screen is shown in Figure 2-14. To see the violet and green screens, press the right button. Press the left button to go to the test select screen. Check the following on the screens:

  • The grid lines should be straight within 3 mm, and the lines should not pincushion or barrel.
  • The convergence of the lines on the violet and white screens should be within 2 mm. If these screens do not meet these criteria, adjust the video display as described in the video display manual.

Figure 2-14 Convergence Test Screen

Page 25

CHAPTER 3

Troubleshooting

and Maintenance

This chapter contains board, and a list of

troubleshooting tables m =ROM-caused problems,

and repair procedures

for your Shuuz™ game. The chapter has two

parts. The first part contains three trouble-

shooting tables. The tables contain general

troubleshooting information, the voltage lev-

els and test points on the game printed-circuit with specific ROMs to check and replace. The last part of the chapter has information about connecting the

video display if it requires separate positive

sync and repair information for the Midi Trak-

Ball control assembly.

Page 26

Troubleshooting and Maintenance Shuuz Universal Kit

Table 3-1 Troubleshooting Table

Problem Suggested Action

Coin Mechanism Problem

| Game Play Problem

Trak-Ball Control Problem

Sound Problem

Video Display Problem sync problems

Screen is dark.

Display area wavers or is too small. Picture is wavy.

Picture is upside down. Convergence. purity or color problems. Picture is not centered. . Check the wiring to the coin mechanism. . Check the vcitage to the + side of the mechanism. . Test the coin mechanisms with the sound test screen in the self-test. 2. 3.

  • Check the harness and connectors.
  • Perform the self-test.
  • Check the voltage levels on the PCB. See Table 3-2, Voltage Inputs and Test Points. 4, Check What ROM Problems Look Like, Table 3-3, for specific ROM problems.
  • Has the Trak-Bail been lubricated with the correct type of lubricant? If not, lubricate it as shown in Figure 4-2 . Check the harnesses and connectors. Check the optical coupler PCBs on the control. If you took the control apart, have you reassembled it correctly? Make sure all the parts on the control are in good repair. Repair or replace parts. vee wy
  • Is the speaker volume turned up?
  • Check the voltage on the JAMMA connector.
  • Check the wiring from the PCB to the speaker. 4, Check the voltage level to the PCB. See Table 3-2, Voltage Inputs and Test Points.
  • Replace the speaker.

Does your display need separate positive sync? See the Video Display Sync Problems section in this chapter. Is the game plugged in? Is the game turned on? Are the connections good? Is the line fuse good? . Is the display brightness turned up? Are the solder connections on the line filter and transformer good? Is the JAMMA connector on the PCB tightly connected?

Check all of the items below. If you answer 70 to any question, you have a

problem with the video display, not with the game circuitry. See your video display service manual. a. Do you have power to the video display? b. Are the video display’s filaments lit? c. Do you have high voltage to the video display?

  • Are the voltage levels to the video display PCB correct? (Power voltage is 100 VAC or 110 VAC. depending on the type of video display. Video signal voltage is 0.5 to 3.5 Volts.)
  • If the level is not correct. check the connectors and the harness.
  • Do you have correct power voltage to the video display PCB?
  • Do you have correct high voltage to the video display?
  • Is the video ground connected to the display?
  • Are the sync inputs connected properly? Does your monitor need a separate positive sync? See the Video Display Sync Problems section in this chapter. Switch the horizontal or vertical yoke wires on the display. Use the screens in the self-test to adjust the video display. Use the adjustment procedures in your video display manual. SIAR

Use the centering procedures in your video display manual.

we Ww

Page 27

Shuuz Universal Kit Troubleshooting and Maintenance

Table 3-2 Voltage Inputs and Test Points on the PCB

Voltage Test Point or LED Source and Purpose

+5£0.25 VDC+5V1Logic power from the switching power supply.

CR7 LED Lights when 5 V is applied to the PCB and the reset (RST) jumper is open. CR4 LED Lights when the +12 V supply is good.

:CR3 LEDLights when the -5 V supply is good.
H+12V+VOP+12 V from the switching power supply. Positive supply for the analog

(pin 4 of LM324) circuitry,

bo-5Vv-voP-5V from the switching power supply (if connected). Negative supply for the

(pin 11 of LM324) analog circuitry.

Table 3-3 What ROM Problems Look Like

ROM Causing

Problem the Problem Check the ROM at:

Program works, but the motion objects orGraphics87W, 65W, 43W, 20W, 87U, 65U. 43U, or 20U

| playtieid are wrong,

| Garbage on screen: program doesn't work.Processor30C

OR Program ROM 0 23P, 13P Game program is erratic.

No sound or erratic sound. Audio ROM: Audio Program 23, 13P Audio ADPCM 65B, 75B

Video Display Sync

Problems

Some video displays cannot use the composite negative sync that is on the JAMMA connector. The Shuuz kit includes a standard Atari Games video connector (located at 12A) that provides separate positive sync. Refer to Table 3-4 and make the appropriate connections for your video clisplay. For other problems, see the video display manual that came with your game.

Table 3-4 Atari Games Video Connector Pin Assignments

Pin Signal Pin Signal

joRed7
2GND82
|&Kev9Negative com-
|4Green,posite synct
15GND10Positive Vi
|6BlueuPositive H syne

Midi Trak-Ball Control

Routine maintenance of the Midi Trak-Ball control consists mainly of inspecting the roller shafts for excessive wear and periodically lubricating the bearings.

Removing the Midi Trak-Ball 1, Open the control panel, and disconnect the harness at the six-pin connector.

  • Remove the four nuts and carriage bolts that secure the Midi Trak-Ball assembly to the control panel.

Disassembling the Midi Trak-Ball To disassemble the Midi Trak-Ball after it has been removed from the control panel, remove the six screws that secure the upper and lower frames (see Figure 4-2). Lift off the upper frame. The Midi Trak-Ball can now be disassembled.

Inspecting the Midi Trak-Ball

  • With the Midi Trak-Bail disassembled, inspect the roller shafts and the idler shaft for excessive wear (see Figure 3-1). If the wear band exceeds 3/8 inch. replace the roller shaft as described in steps 2-6, or replace the idler shaft as described in steps 7-10.
Page 28

‘Troubleshooting and Maintenance

vv To replace a roller shaft, first remove the roller shaft from the lower frame. we Remove the metal encoding wheel by loosening the socket-head screw, flat washer, and split-lock washer, Remove the encoding wheel and bearings. +. Remount the bearings and encoding wheel on a new roller shaft. uw Tighten the encoding wheel by inserting a 1/8inch-diameter pin or screwdriver through the hole in the shaft. Tighten the socket-head screw with an Allen wrench.

  • Reinstall the roller shaft in the lower frame. “4 To replace the idler shaft, first remove the idler shaft from the lower frame.
  • Remove the bearings from the ends of the idler shaft.
  • Remount the bearings on a new idler shaft.
  • Reinstall the idler shaft in the lower frame.

Lubricating the Midi Trak-Ball Lubrication of the Midi Trak-Ball assembly should be performed every three months or 6,000 credits (as counted on the coin counter). To lubricate, place two drops of a light-duty oil, such as 3-In-One oil, on each of the six ball bearings shown in Figure 4-2.

Figure 3-1 Excessive Shaft Wear Shuuz Universal Kit

Replacing the Coupler PCB

  • To remove the Coupler PCB, first disassemble the Midi Trak-Ball. Lift the PCB out of its slot. Carefully disconnect the red connector and remove the PCB.
  • To reinstall the Coupler PCB, place the PCB in the slot in the lower frame, and reconnect the red connector.
NOTE When you reinstall the Coupler PCB, make sure that the metal encoding wheel is not bent or damaged. Be sure the encoding wheel turns freely between the two halves of the radial optical coupler.

Reassembling the Midi Trak-Ball

  • Install the upper frame of the Midi Trak-Ball over the assembly. Be sure that each Couple PCB is engaged in the slots of the upper frame. is) Replace the six screws that secure the upper and lower frames together. Remount the Midi Trak-Ball assembly to the control panel using the four nuts and carriage bolts. we
  • Reconnect the six-pin connector of the harness.

OMs and RAMs

If you have think you have bad ROMs or RAMs, preform the ROM or RAM test in the self-test. If you have a ROM problem, see Table 3-3.

Page 29

CHAPTER 4

Parts Illustrations

This chapter provides

information you need to

order replacement

parts for your kit. Common hardware parts,

such as screws, nuts, washers, and so on, are

included in these parts illustrations. When

you order parts, give the part number, part

name, the number of this manual, and the serial number of

your game. With

this information,

we can fill your order rapidly and correctly.

We hope this will create less downtime and

more profit from your games. Atari Games

Customer Service phone numbers are listed

on the inside front cover of this manual.

Page 30

Purts Illustrations Shuuz Universal Kit

Items Not Shown: | ‘a04ss01-01 JAMMA Harness Assy. 7358 ‘Shuuz Universal Kit Installation Instvucions 036826-01 | Attraction Shield |

087594-01 | Bezel win Grapnics

‘structions Label {tor Countertoa » Games Oniy)

S se 1 Side Panel Decal

75-51488 7 = | | Shauz pce assy #10 x 3.0" Carriage Bolt = 2 * . &2 178265-001 (st ataces) . : Style Nylon Standott s77010-240 . = 7 | paces) $4 : ope Lena ee 7 a6xae Panto. (4 places) F “ Cross-Rec, Type-AB Screw s7sova-1040 | apaces) moFiaWasner 7 : (4 places)

Volume Controt Selt-Test Switch

178237-006 1 ‘Groen Button Assy. + (2 places) ) 160044-001 ' i ‘Snap-Action Switch (2olaces) + 178283-008 | ‘indicator Plate | H (STARTACTION)| = —___|__ (2 places) ‘A038038-01 Migl Trak-Ball Assy. 04796201 Trak-Balt Adapter Harness Assy. Control Pane! Decal 087209-01 Control Pane! Cover

Figure 4-1 Parts for Shuuz Universal Kit A047980-01 D

Page 31

Shuuz Universai Kit Parts Iilustrations

176010-106 | Screw |

038039-01 | Upper Frame

038043-01 Midi Track-ball

038042-01 Idler Shatt \ 035937-01 Ball beanng

038041-04 Rotler Shaft

035938-01 Encoder Wheel

75-014 Flat Washer

Vertical-Motion PCB Black, Red, Yellow and Green Wires Split-lock Washer

72-8406 Hex Screw

139002-001 | Optical Coupler (hidden from view) Horizontal-Motion PCB Blue, Violet, Red, and Black Wires

038040-01 | Lower Frame} Anas220/02 | Coupier PCB Assy.

A036096-01 | Harness Assy. |

Figure 4-2 Midi Trak-Ball Assembly A038038-01 G

4-3

Page 32

uz Universal Kit

Figure 4-3 Shuuz Game PCB Assembly A047365-01 A

Page 33

CHAPTER 5

Schematic Diagrams

This chapter contains printed at the end the schematics dia- of this chapter. (The

rams for your game boar f g board assem:

Shuuz™ game PCB. In bly drawing is illustrated in

addition, the faulty RAM/ROM tables are Chapter 4, Parts Illustrations.)

Page 34

Schematic Diagrams Shuuz Universal Kit

SPARE GATES

Ls8e

+5V

Leys Leys Tce: ese Tess Less Less Leso Les Lero

op.yet27LTtTLTLtLTtTL
|oeeelIaeeeI

Lert ac72 icys icez icye icy ieee icy ics =ce3

~tT.T*TT:*Tt.TT’

icrs ier? ices ices Lege icp Leer Lees icity Leys

oT TeTtTeTtTeTtTT

ep Loge 2og' ego acy icis ici cps Lcpoe ACga p02

tet?Teeee ee|
ee aaes Se

Lcpoz czas depos scene cpor Legos icpos icpie cz Lejte

Ipet*Tt7T**i

Acis4 Leroo ters Leis

JAM-H>- — JAM-BB >> JAM-7 >= JAM=25 >> JAM-K >> JAM=CC >> JAM=9>- — JAM-26 >

NOT STUFF -Sv +12V —>AUOK-1 AUDX-2 ACND _S auox-3 AUOMP Shuoxee BUXS _S gupx-s AUK _S quox-6 GND _S quox-7 AGND _S aupx-8 —Saunx-4 7PUX _S guox-10 GND _Saupx-11, 06 Sauox-12 OS _Sauox-13 GND _§ auox-14 SNO _S aupx-15 (OY —Sauox-16 03 Seupx-17 SND _S aunx-18 Saunx-29 02 _S auox-20

na —Saunx-21bo 7S AUDK-22-O FIDUCIAL PARK

AUOX-23 /AUDX-24

esozcLn SameYAMCLR aioe-O FIDUCIAL PARK
MAI _S quox-27SND _S auox-28-O FIOUCIAL MARK

Saunx-29 /SINT _S aupx-30

/VINT Seunx-31SNO _S aunx-32-O FIDUCIAL MARK

—Saunx-33 S-TEST _S aunx-34 WAR _Seunx-35 NO _S aupx-36 SND _Squox-37 /AUDRES _S aunx-38 “80 Saunx-39 *8¥ _Sauox-40

¥ w

Page 35

Shuuz Universal Kit Schematic Diagrams

JAM-3 >— JAM-4 >— R120 Pr osu AMC — eu | 20K voy desy ess gas | vt t JAM=% rae oor !--“4 JAM-2>——+ NDZ CNDL = cND3 cy JAM-A yt -3>— at ve | C133 copra JAN-EE >— rr ae JAM-FF > : cis go JAM-27 — cco JAM-28 >-— pm sorta => +Sv i s) = ei

CRS Fino

SI/0O

Figure 5-1 Shuuz Game PCB Assembly Schematic Diagram 047366-01 A

Page 36

Schematic Diagrams

+5V.

VERPHR ————-

wan-y 2

anew 2M 1 JAM*17

sAM-x

JAM-S

JAM-T

Ame24 R53 $ R26 S$ Rzs

87024708470

R1Z Ril

Rae RYO S R1VS R29

47034708470

Ri?

( ] I ] R27

t I l ! l R34

wane 22S!i|R24sx"

Shuuz Universal Kit

tk Rue

NOT STUFFED

Page 37

Shuuz Universal Kit Schematic Diagrams

x= SRéoos x $Reoos

JAM-8 R28 OvL/H

LETA

Figure 5-1 Shuuz Game PCB Assembly Schematic Diagram 047366-01 A

Page 38

Schematic Diagrams

*5V

y POWER:

Sv ‘ON

0" 2

eB

/SINT

/SYSRES

/VOTACK

/OTRCK ah re coHl— /SYSRES ae Fok

Lso8 SU

RoL

]2 ewia3} yeaa Shuuz Universal Kit

Page 39

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 40

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 41

Diagrams Shuuz Universal Kit ‘Schematic Diagra

ae |e Rea 35 oes |. 208 20K ae ceo F -Soes ACNO——> JAM=H sume —____]

o36 =e > JAM=10 4707250

res San 30K $ 220

ae JRM-E (70h SS eon w/sR— [S52

/OTRCK Aasaaal 7PM 1 800 RA — nos tisz60 (S86 ce8 i

180PF Rat

470K s12y

R78

—Reo 2.2K] oysol,
st22k R77 |RUOMP
tle, = carli0_o72 ok-3v

23 ort 06 Rra | SEL, pas 5, 820 RES ope ou esozcux Ele ona 03 Sr) Mrests az

Figure 5-1 Shuuz Game PCB Assembly Schematic Diagram 047366-01 A

Page 42

Schematic Diagrams Shuuz Universal Kit

=n wine Bere as ye aa aw ACL [Croc e502CLK YRMCLK,

OK TO PUBLISH

JHSYNC Rioz $ r103 $ rey 470 3470 S470

| VID-12

i

** NOT STUFFED

5-10

Page 43

Shuuz Universal Kit ‘Schematic Diagrams

RGRaeRiotLene
nr oe5.6K4.3K100in

VID-2

2.2k Ri0e**

4 OTK 2N3905

vID-4

R105R107R140£25,
5.6K4.3K100L00Pr

VID-S

aie s* bak 1 sam=13

7K anaag

vin-6

RATR123| ee
5.6K4.3K100

vio-7

XGB

Figure 5-1 Shuuz Game PCB Assembly Schematic Diagram 047366-01 A

Page 44

Schematic Diagrams Shuuz Universal Kit

27K Rio

270K

R8 c3 3.3K aa

Ja-g ONO

ASSEMBLY

Figure 5-2 Shuuz Coupler PCB Assembly Schematic Diagram 047870-01 B

ye An i)

Page 45

Shuuz Universal Kit

Bad RAM Locations by Error Address

RAM Location |

Error AddressHighLow|
3F00004IN70N
3F400034K54K

Bad ROM Locations by Error Address

RAM Location: Error Address High Low OK 23P 13P

Figure 5-3 Faulty RAM/ROM Tables Schematic Diagrams