CATHODE RAY TOMES

Road Riot 4WD TM-369 1st Printing

Road Riot 4WD (04 Dec 1991, conversion kit) (Atari Games, 1991) · Technical Manual · 52 pages · 52 sections · original scan

Page 1

<7

Page 2

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 3

Arai

Page 4

Copyright © 1991 by Atari Games Corporation. All rights reserved. No part of this publication may be reproduced by any mechanical, photographic or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher. The game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the U.S. Copyright Act of 1976. This Act provides for substantial penalties for violating federal copyright

WARNING Use of non-Atari parts or modifications of any Atari game circuitry may adversely affect the safety of your game, and may cause injury to you and your players. laws. Courts can impound infringing articles while legal action is pending. If infringers are convicted, courts can order .destruction of the infringing articles. In addition, the Act provides for payment of statutory damages of up to $50,000 per infringing transaction in certain cases. Infringers may also have to pay costs and attorneys’ fees and face an imprisonment of up to five years as well as fines of up to $250,000 in the case of individuals and up to $500,000 in the case of corporations.

Atari Games Corporation will aggressively enforce its copyrights against infringers. We will use all legal means to immediately halt any manufacture, distribution, or operation of a copy of video games made by us. Anyone who purchases such copies risks forfeiting such a game. Published by: Atari Games Corporation 675 Sycamore Drive P.O, Box 361110 Milpitas, California 95036-1110 Printed in the U.S.A. 5/91 Produced by the Atari Games Technical Publications Department. Writing and Editing: Andrea Dencker Illustration and Design: Mary Ohanessian Sumner You may void the game warranty (printed on the inside back cover of this manual) if you do any of the following: © Substitute non-Atari parts in the game.

  • Modify or alter any circuits in the game by using kits or parts not supplied by Atari Games Corporation.
NOTE This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of Federal Communications Commission (FCC) Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area or modification to this equipment is likely to cause interference, in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference. If you suspect interference from an Atari game at your location, check the following:
  • All ground wires in the game are properly connected as shown in the game wiring diagram. © The power cord is properly plugged into a grounded three-wire outlet.
  • On games provided with an Electromagnetic Interference (EMI) ground plane, be sure that the game printed-circuit boards (PCBs) are properly installed on the EMI ground plane and that the end board is securely installed with alll screws in place and tightened. If you are still unable to solve the interference problem, please contact Customer Service at Atari Games Corporation. See the inside front cover of this manual for service in your area.
Page 5

SAFETY SUMMARY

The following safety precautions apply to all game operators and service personnel. Specific warnings and cautions will be found in this manual whenever they apply.

WARNING Properly Ground the Game. Players may receive an electrical shock if this game is not properly grounded! To avoid electrical shock, do not plug in the game until it has been inspected and properly grounded. This game should only be plugged into a grounded threewire outlet. If you have only a two-wire outlet, we recommend you hire a licensed electrician to install a three-wire grounded outlet. If the control panel is not properly grounded, players may receive an electrical shock! After servicing any part on the control panel, check that the grounding wire is firmly secured to the inside of the control panel. After you have checked this, lock up the game. AC Power Connection. Before you plug in the game, be sure that the game’s power supply can accept the AC line voltage in your location. The line voltage requirements are listed in the first chapter of this manual. Disconnect Power During Repairs. To avoid electrical shock, disconnect the game from the AC power before removing or repairing any part of the game. If you remove or repair the video display, be very careful to avoid electrical shock. High voltages continue to exist even after power is disconnected in the display circuitry and the cathode-ray tube (CRT). Do not touch the internal parts of the display with your hands or with metal objects! Always discharge the high voltage from the CRT before servicing it. Do this after you disconnect it from the power source. First, attach one end of a large, well-insulated, 18-gauge jumper wire to ground. Then momentarily touch the free end of the grounded jumper wire to the CRT anode by sliding the wire under the anode cap. Wait two minutes and do this again. Use Only Atari Parts. To maintain the safety of your Atari game, use only Atari parts when you repair it. Using non-Atari parts or modifying the game circuitry may be dangerous, and could injure you and your players. Handle the CRT With Care. If you drop the CRT and it breaks, it may implode! Shattered glass from the implosion can fly six feet or more. Use the Proper Fuses. To avoid electrical shock, use replacement fuses which are specified in the parts list for this game. Replacement fuses must match those replaced in fuse type, voltage rating, and current rating. In addition, the fuse cover must be in place during game operation.
CAUTION Properly Attach All Connectors. Make sure that the connectors on each printed circuit board (PCB) are properly plugged in. The connectors are keyed to fit only one way. If they do not slip on easily, do not force them. If you reverse a connector, it may damage your game and void your warranty. Ensure the Proper AC Line Frequency. Video games manufactured for operation on 60 Hz line power (used in the United States) must not be operated in countries with 50 Hz line power (used in Europe). If a 60 Hz machine operates on 50 Hz line power, the fluorescent line ballast transformer will overheat and cause a potential fire hazard. Check the product identification label on your machine for the line frequency required.

ABOUT NOTES, CAUTIONS, AND

WARNINGS In Atari publications, notes, cautions and warnings have the following meaning:

NOTE — A highlighted piece of information.
CAUTION — Equipment and/or parts can be damaged or destroyed if instructions are not followed. You will void the warranty on Atari printed-circuit boards, parts thereon, and video displays if equipment or parts are damaged or destroyed due to failure of following instructions. ‘WARNING — Players and/or technicians can be killed or injured if instructions are not followed.

we

aa,

iii

Page 6

Co TENTS

1 Set-Up How to Use This Manual . Inspecting the Game... Control and Switch Locations . Installing the Seat Assembly. Installing the Roll Bars .. Final Inspection ..... Setting the Coin and Game Options, Game Pg 2 Self: Test ym Introduction... Entering and Exiting the Sel Self-Test Menu °..2. Adjust Volume Game Statistics Histograms...

Alpha Test .. Motion Object Test Playfield:’Tes Switch Test.

Complete | RAM, po

i

iv 3 Troubleshooting and Maintenance

Maintaining the Coin Mechanism Repairing the Video Display Steering Control. Steering Motor. .Foot Pedal Assembly . [ROMs and RAMs 4 Parts Illustrations

.See the List of Illustrations that follows.

Page 7

Figure 2-1 Figure 2-2 Figure 2-3 Figure 2-4 Figure 2-5 Figure 2-6 Figure 2-7 Figure 2-8 Figure 2-9 Figure 2-10 Figure 2-11 Figure 2-12 Figure 2-13 Figure 2-14 “RATION

Self-Test Menu Screen .. Adjust Volume Screen. Game Statistics Screen. Coin Options Screen Game Options Screen . Alpha Test Screen..... Motion Object Test Screen .. Playfield Test Screen Switch Test Screen Color Test Screen.. Convergence Test Screen Sound Test Screen ASIC65 Test Screen RAM Test Screen... Figure 4-1 Figure 4-2 Figure 43 Figure 4-4 Figure 4-5 Figure 4-6

Figure 4-7 Figure 4-8 Figure 4-9

Table 1-1

Table 2-1 Table 2-2 Cabinet-Mounted Assemblies... Shaker Steering Control Assembh

Four-Entry Coin Door Power Supply Assembly... Road Riot 4WD Game PCB Assembly JSA III PCB Assembly ... Comm-RAM PCB Assembly Solenoid/Motor PCB Assembly

Game Specifications . 1-2 Fi Summary of All Self-Test Screens : Game Option Settings . Coin Option Settings

Troubleshooting Table...! Voltage Inputs and Test

Page 8

vi

Page 9

CHAPTER

Set-Up

How to Use This Manual

This manual is written for opera-

tors and service personnel. It provides information for setting up, playing, testing, and maintaining your Road Riot 4WD” two-player game. The manual is divided into the following chapters: ® Chater 1 contains set-up and game playing information. © Chapter 2 describes the se how to use the self-test screens. ® Chapter 3 contains maintenance, repair, and troublef-test and shooting procedures. Be sure to perform the preventive maintenance tasks to keep the game in good condition. ® Chapter 4 contains the parts illustrations. ® The

accompanying Road Riot 4WD Schematic Package (SP-369) contains the schematics for the Road Riot 4WD game printed-circuit board (PCB), JSA II] PCB, Comm- RAM (common RAM) PCB, and the wiring diagrams.

Page 10

Set-Up

Inspecting the Game

WARNING To avoid electrically shocking yourself and damaging the game electronics, do not plug in the game until it has been inspected and set up for your line voltage.

This cabinet should be connected to a grounded threewire outlet only. If you have only two-wire outlets, we recommend that you hire a licensed electrician to install grounded outlets. Players can receive an electrical shock if the cabinet is not properly grounded. Inspect your Road Riot 4WD game carefully to ensure that the game is complete and was delivered to you in good condition. Inspect the cabinet as follows:

  • Examine the exterior of the cabinet for dents, chips, or broken parts.
  • Open the service door. Unlock and open the coin doors. Inspect the interior of the cabinet as follows: a. Check that all plug-in connectors on the cabinet harnesses are firmly plugged in. Do not force connectors together. The connectors are keyed so they fit only in the proper orientation. A reversed connector can damage a printed-circuit board (PCB). This will void your warranty. b. Ensure that all plug-in integrated circuits on each PCB are firmly plugged into their sockets. c. Inspect the power cord for any cuts or dents in the insulation. d. Inspect the power supply. Make sure that the correct fuses are installed. Check that the harness is plugged in correctly and that the fuse block cover is mounted in place. Check that the green ground wires are connected.

Table 1-1 Game Specifications Characteristic.

“Line Fuse Rating Line Voltage ee Temperaturé _ 5° to 38°C. (37° to 100° F). Humidity Not to exceed 95% relative Weight 650 Ibs. (1430 kg), me=Dimensions (after asseribly): Width = 49.25 inches (125 cm) Depth 61.5 inches (156.2 cm) “Height “°° 66 inches (167.6 cm)

1-2 e. Inspect other sub-assemblies, such as the video display, controls, printed-circuit boards (PCBs), and speakers. Make sure that they are mounted securely and that the ground wires are connected,

Control and Switch Locations

Most of the controls are located inside the coin door. The only exception is the power on/off switch. Power On/Off Switch The power on/off switch is located at the bottom rear of the cabinet.

Volume Control There is no longer a volume adjustment knob on the game PCBs. Volume is now adjusted in the self-test. Refer to Chapter 2 of this manual for more information. Self-Test Switches This game has two self-test switches — one for each game PCB or each monitor. The switches are located on a metal bracket inside the coin door.

Coin Counters ‘Fhe coin counters are also located inside the coin door, on the same metal bracket.

Installing the Seat Assembly

Make sure the game power is turned off. To install the separately packaged seat assembly, you need a hex driver or wrench. Follow these steps to attach the seat assembly onto the game:

  • Reach in through the rectangular front opening at the bottom center of the game. (See Figure 4-1.) Pull out both power cords.
  • Move the seat assembly up to the front of the game cabinet. Plug the power cord labeled LEFT into the left socket on the seat assembly, and plug the other one into the right socket.
  • Move the seat assembly up flush to the game, being careful not to pinch any excess power cord. Match the seat platform height with the cabinet height by adjusting the leg levelers.
  • Loosely place one black side bracket on each side of the cabinet. Install four flat washers and tamperproof screws into the four holes provided on each side (see Figure 4-1). As you tighten the screws, press each bracket firmly against the sides of the seat assembly and cabinet.
Page 11

Installing the Roll Bars

  • Unwrap the protective covering on the roll bars. Lift each roll bar into place, so that the large plate end slides down behind the seat but in front of the rear wood panel on the seat assembly. 2, Attach the large plate to the seat assembly by inserting a black 1.25" tamperproof screw and flat washer into each hole on the outside of the wood panel. Behind the seat attach a large fender washer and acorn nut. Tighten the hardware.
  • Secure the top of the roll bar by inserting black 1.25" tamperproof screws with flat washers into the slots on the small roll-bar plate and then into the cabinet holes, Tighten the hardware.

Final Inspection

  • Turn on the game power. Check that the video display and the attraction lamp have power.
  • Observe the screen; you should see the attract mode displayed. If the screen remains a solid color, you have a video or CPU RAM failure. If you see a black-and-white screen, you have a color RAM failure.

Setting Coin and Game Options

The Road Riot 4WD coin and game options are set in the self-test. Refer to Chapter 2 for the recommended settings and the procedure for setting the options.

Game Play

This section describes the features and driving of the Road Riot 4WD” game.

Introduction Road Riot 4WD presents off-road racing competition combined with combative shooting action. Players can compete head-to-head, driving high-performance offroad vehicles armed with a stun gun. The unique cabinet design is complete with roll bars to attract Road Riot 4WD racers of all ages.

Road Riot 4WD is a one- or two-player off-road racing game where players can compete for an overall season championship. The side-by-side, two-monitor configu- Set-Up

ration encourages two-player linked competition; however, players can also choose to play individually. Controls include a gas pedal and a feedback steering control with trigger buttons. When the car drives off the race course, the game gives a realistic off-road feel to the player through a unique motor-driven steering control. Road Riot 4WD also includes the innovative “rump-thump” feature; the trigger buttons on one player’s control activate a solenoid in the seat of the other player, resulting in a unique sound and feel. The player is challenged by the lifelike skidding and bouncing action of his four wheel drive vehicle on the track. The car can also crash in several different ways, depending upon how an object is hit. The car can roll on its side, fly end-over-end, or even explode on impact. Twelve different tracks offer special terrain and competitor challenges. Each track has a different background, tanging @ from desert to mountains, corn fields to ice 3% fields. Terrain and track obstacles vary for each setting. There are several incentives for two-player simultaneous play. Two players can compete head-to-head against each other for the season championship of 11 different race courses. The road riot will continue as long as the player defeats the hosting opponent's team yellow cars. If two players are playing a linked game, there is one less computer-controlled car to beat. Two players can cooperate to beat the opponent cars. The competition between two players in a linked game is also heightened with Atari's innovative “rumpthump” feature. When one player hits the other with the stun gun, a solenoid located within the seat gives an audible kick as the player is “shot.” Video graphics are digitized pictures of real-life objects. The Road Riot 4WD racing vehicles, people, and obstacles on and around the track are realistically depicted. The life-like detail and humorous interaction with the video graphics enhances player appeal.

Page 12

Set-Up Road Riot 4WD.

1-4

Page 13

CHAPTER 2

Self-Test

Use the Road Riot 4WD” self-test

to check the condition of the

game circuitry and controls. You will see the self-test information

on the video display and hear the sound test information through the speakers. You do not need any additional equipment to perform the self-test. @ You should perform the self-test w:

INTRODUCTION

en you first set up the game, each time you

collect the money, or when you ® This chapter shows the screens in the suspect game failure.

self-test and explains each of the tests. The screens and explanations are arranged in the order they appear in the self-test. Table 2-1 lists all of the self-test

screens and their purposes.

Page 14

Self-Test Road Riot 4WD

Entering and Exiting

the Self-TestADJUSTVO

To enter the self-test, turn on the two self-test switches GA on the bracket located behind the left side of the coin ise door. Exit the self-test by switching off the two self-test

switches, They can be turned on or off individually.A SeeES

BLA D Self-Test Menu : GLOR Choose which test or screen you want to see from this OMEN menu, shown in Figure 2-1. Move up and down the QUE list by pressing the left and right triggers; the corre- ae

sponding test is highlighted in blue. Choose the screenSHee

by pressing the START button. O 9 MA

Adjust VolumeRIGS-SELEGTSTARTDO TES

Adjust the volume of the game using this screen, shown in Figure 2-2. Control the volume by pressing the left and right triggers; the volume number increas- Figure 2-1 Self-Test Menu Screen es or decreases. To restore old volume level, push pedal. Save the new volume and return to the self-test from the last time the statistics were cleared. You can menu by pressing the START button. clear the statistics by pressing both triggers at the same time. Press the START button to leave this screen and Game Statistics go to the histograms. ° Left Coins show the number of coins counted in Use the information shown on the statistics screen, in the left coin mechanism. Figure 2-3, and on the histogram screens to keep track of your game use and maximize your profits. Record the information on the Road Riot 4WD statistics page in the back of this manual. The statistics are collected

  • Right Coins show the number of coins counted in the right coin mechanism.

Table 2-1 Summary of All Self-Test Screens Screens: oUseor Purpose Adjust Volume’ 9 Adjusts the volume.

Game Statistics Screen. ‘Displays thé ‘game statistics

“ Goin Options Screen ‘Use to. set and check the: Game Options Screen Use to set and'check the Alpha Test Screen Use to > test for clarity of characters. ‘Motion Object Test Screen’ Use to tést the mover Playfield Test Screen’ Use to check the play Switch Test Screen os Use. to display the fun

Color Test ScreenorUse to check the vididisplay colorCults.

Convergence Test Screen ” “Aseriés of scréens to check and adjust display convergence » White Convergence Screen Use 'to check and adjust video display Convergence of red, blue, Violet Convergence Screen Use to-check and adjust video display ‘convergence of ted to blue. Green Convergence Screen “Use to check and adjust video display convergence of ted and blue to green. Sound Test Screen Use to check the audio circuits.:; ASIC65 Test Screen Use to test comm port, checksum, and internal RAM.

Common RAM Test ScreenUse to check common RAMs.2

Complete RAM/ROM Test Screen pad io Check the all RAMs’ and d program ROMs. = S ote Sa.

2-2

Page 15

Figure 2-2 Adjust Volume Screen

  • Aux Coins shows the number of coins counted on the auxiliary coin input.
  • New Games is the number of new games played. © Continuation is the number of continued games played.
  • Free Games is the number of free games played if Coin Options is set to free games. « Idle Time shows the number of minutes the game was not being played.
  • Active Time is the number of minutes the game was being played in any mode.
  • Solo Time is the number of minutes a race was being held in single-player mode
  • Linked Time is the number of minutes a race was being held in two-player mode. ¢ Shaker Time is the number of minutes the shaker motor inside the steering control was running.

° E

Ao0
ee68

ir a me

Hustip

otal Cre

olalCo4
PROTHTR
fe)ASTATS
PRESSSTARTFOROGRAMS

Figure 2-3 Game Statistics Screen Self-Test

  • Thump Count is the number of thumps received per seat. ° Error Count shows the number of errors counted in the erasable memory. If you have an error count, the statistics may be wrong. If you consistently have errors counted for several weeks, replace the EEROM at 38F.

Histograms

The histograms are two screens that contain information about the game. Press the START button to move to the next histogram. To clear all histograms, press both triggers while displaying the last histogram screen. Press START to exit from the last screen. The first histogram shows new game times, and the second has continued game times.

Coin Options

Check and select the coin options on this screen, shown in Figure 2-4, To move through the options, use the right trigger. Change the option in yellow type. The factory default settings are shown in green. To change a setting, use the left trigger. To save the new settings, press the START button. This returns you to the select test screen. If you want to keep the original setting, although you have changed it, press the pedal. This brings back the original factory setting. Use the START button to exit. The coin option settings and factory defaults are explained in Table 2-3.

Game Options

Check and select the game options on this screen, shown in Figure 2-5. To move through the options, use the right trigger. Change the option in yellow type. The factory default settings are shown in green. To change a setting, press the left trigger. To save the new settings, press the START button. This returns you to the select test screen. If you want to keep the original setting, although you have changed it, press the pedal. This brings back the original setting. Use the START button to exit. The game option settings with factory defaults are shown in Table 2-2.

Alpha Test

The alpha test consists of a series of screens that you use to test the clarity of characters. Figure 2-6 shows the first of the alpha test screens.

2-3

Page 16

Self-Test

Table 2-2 Game Option Settings

Option: :eeSettings.

Difficulty Level* —

}:eo

Music in Attract Seat Thumper

Posed ge

Clear High Score Table _ Steering Shaker Motor

Auto High Seore Reset En: *You must set both ‘players to the same difficulty seittin

:

“Medium “Easy” Easier: Easiest

Hardest Harder Hard Medium Hay

ifthe settings ‘don't agree, you ‘can change them both to medium by. c eae START f

Figure 2-4 Coin Options Screen.

The screens display all of the alphanumeric character sets. If the screens are not clear, you have a problem. To move through the screens, press either the left or right trigger. Use the START button to exit.

Motion Object Test

The motion object test screen, shown in Figure 2-7, tests the movement and color of various game objects. Select the test function with the START button. Use the pedal or steering control to move objecis, change pictures, and change object size. Press the START button to move to the next test or exit.

2-4

GOINOPTIONAMEOPTIO
DEFARSpR

REE PLA . 0 D

DISCOaceR

e

6OsAPER
0RED°
BOFOR GBARSCORETAS
RARRMOTOR
OINCOOoD
CHVA3SCORE R
QINCOAS 1 COIN8.
PRAA6OPTIOprp5RTOOPTIO
RESSRiaTKPARIO
PRBEDALTO-RESETFACTORY OPTIOPRPEDALTORACTORY OPTIO
STARTTONGSANDpAART 10 SAGS AND

Figure 2-5 Game Options Screen.

Playfield Test

This test, shown in Figure 2-8, checks the condition of the scrolling playfield. Move the steering control left/right to see horizontal movement on the screen. Hold the right trigger button while moving the control left/right to see vertical movement. Press the START button to exit the test.

Switch Test

The switch test allows you to display the status of the game switches and controls. The switch test screen appears in Figure 2-9, The items tested are:

Page 17

Road Riot 4WD Self-Test

Table 2-3. Coin Option Settings

xplanation... ~~ : Setthis: to “Yes” for “demonstrating gare “Lets ea re | Option Soot Settings... s— Free Plays Now Yes Discount to Continue Nov Yes

Game Cost" 2 coins 1 credit ”

8 coins 1 credit Bonus for Quantity Buy-in None v

  • coins give 1 (extra coin) 3 coins give 1 3 coins give 2
  • coins give 1 a 4 coins give 2 2 4.coins give 3 5 coins give1 5 coins give 2 5 coins give 3 6 coins give 1 6 coins give 2 : 6 coins give 3 oa 7 coins give 1 7 coins give 2 7 coins give 3 x e 8 coins give 1° 8 coins give 2° 8 coins give 3 9 coins give 1 cu 9 coins give 2 ‘é 9 coins give 3

Right Mech Value 1 coin counts as 1 coin Vv

Re 1 coin count as 8 coins Left Mech Value 4 coin counts as 1 coin 4 eg coin mechanism.

  • 1 coin count as 8 coins v Manufacturer’ fecommended settings. These sellings 2 are e show | in green on ‘the cee

Figure 2-6 Alpha Test Screen. Figure 2-7 Motion Object Test Screen

2-5

Page 18

Self-Test

Figure 2-8 Playfield Test Screen.

  • Steering wheel left/right movement © Foot pedal potentiometer
  • Left trigger and steering shaker motor ¢ Right trigger and thumper solenoid © Start switch and start 3% lamp As you activate each e switch or control, make sure the correct words are highlighted in blue on the screen. Figure 2-9 shows all three momentarily-on controls in outline type. However, all three phrases would normally not be displayed simultaneously, because you would have to press the left and right triggers and start button at the same time. If players complain of cars driving erratically, or whenever the contro! harness is unplugged, you must recalibrate the controls. Follow this procedure to do the calibration:
  • Press the right trigger and start button simultaneously. The numbers after WHEEL and PEDAL on-the screen will change.
  • Turn the steering control to its right limit, and hold it there for 4 seconds. Then turn it to its left limit and hold it there for 4 seconds.
  • Press and hold the foot pedal for 4 seconds. 4, Simultaneously press both triggers to save the calibration and exit from the switch test. Do not simply turn the self-test switch off to exit from this test: doing so will not save the calibration. OSTARTTOR a

AND RTRIG TO

Figure 2-9 Switch Test Screen

Color Test

This test indicates the dynamic range of the video display color circuit in a series of seven screens. The first color test screen is shown in Figure 2-10. Advance to each screen by pressing the right trigger (the software cycles through all seven screens and then starts over again). The screens are as follows:

  • Red at the top, followed by green, blue, and white
  • Yellow at the top, followed by light blue, purple, and white Solid red Solid green Solid blue Solid white Solid gray NAW Aw

colon tes

Figure 2-10 Color Test Screen

Page 19

If the screens do not match this description, adjust the video display as described in the video display manual. Press the START button to exit.

Convergence Test

The convergence test has three screens: first white, then violet, and finally green. The white screen is shown in Figure 2-11. To see the violet and green screens, press the sight trigger. Press the START button to go to the test select screen. Check the following on the screens:

  • The grid lines should be straight within 3 mm, and the lines should not pincushion or barrel.
  • The convergence of the lines on the violet and white screens should be within 2 mm.

Figure 2-11 Convergence Test Screen

If the screens do not meet these criteria, adjust the video display as described in the video display manual.

Sound Test

The sound test indicates the condition of the sound effects circuit on the game PCB. The sound test screen appears in Figure 2-12. Use the steering wheel control to select the sound, and press the right trigger to listen to it. Pressing the left trigger stops the sound from playing. Press the START button to return to the select test menu.

ASIC65 Test

Use the ASIC65 test screen to test the comm port, checksum, and internal RAM. The first screen is shown in Figure 2-13. You can select one of the three options Self-Test

Figure 2-12 Sound Test Screen

shown. Use the left trigger to move to the next option. Use the right trigger to select an option. If you test the comm port, a message indicates whether or not it’s OK. The checksum option displays the checksum. The internal RAM test indicates whether or not the RAM is OK. Press the START button to exit.

Comm (Common) RAM Test

Use this selection screen, shown in Figure 2-14, to see if the common RAM is OK. This test is automatically run when you switch to garne mode. When the test runs successfully, you see the message COMMON RAM OK! If the RAM is bad, the message COMMON RAM ERROR is displayed and you must replace the Common RAM board. Press the START button to exit.

Figure 2-13 ASIC65 Test Screen

2-7

Page 20

Self-Test

2-8 Figure 2-14 RAM Test Screen Complete RAM/ROM Test The RAM/ROM test tests both RAM and ROM. When you run this test, you see a sequence of color screens. If the screens turn to black and white or gray or if no message appears, the RAM is bad. You need to replace it. If the ROM is bad, the checksum of the bad ROM is displayed. You need to replace that ROM. Press the START button to exit.

Page 21

CHAPTER 3

~ Troubleshooting

and Maintenance

This chapter contains troubleshoot-

ing tables and repair procedures for your Road Riot 4WD™ game.

The chapter includes several troubleshooting tables. The tables contain general troubleshooting inforreplace, and a description of steer-

ing motor problems. The chapter

also includes information about

connecting the video display if it requires separate positive sync and

repair information for the steering

mation, the voltage levels and test points on the contro! and foot pedal assembly, and locations

game printed-circuit board, a list of ROM-caused of the RAMs and ROMs on the game PCB.

problems with specific ROMs to check and

Page 22

Troubleshooting and Maintenance Road Riot 4WD

Table 3-1 Troubleshooting Table

  • Perform the Self-test. 8..Check the oleae ie levels « on the PCB. See Tap) «Points: - : -"4.Cheok What ROM Pro! Steering Control Problem, 4, Have the controls been | Foot Pedal Problem lubricate them as shown
ZSi2. Check the harnesses and connectors.

. Check the’switches on the. control. If you took the control apart; “have you re . Reset the limits on the | steering control and t cls the ‘speaker volume turned up? (Volume | . Check the voltage on the JAMMA connecto

  • Check the wiring from the PCB to'the s; Check the voltage level
AEReplace the speaker

Video Display Problem fags Screen is dark. Is the game plugged oe = Is the game turned on’ . Are the connections gi sols the'line fuse:good?? 2)"

. Is the display brightness turned up’

..Afe the'solder connections on the iin Sound Problem = Giang iets Paro

NORM display service manual. ~a.Do you have ‘power to the-vi leo di Are'the video display's filamen S i

Only acolored screen: appears. You probably "have a’ serious RAM pl olem. Display ‘area wavers or.” 1. Doyou have correct pov volt ge to the video diply CB?

is too small.62.°Do’ you: have correct highge tothe video displ i
=Picture is WAY.21. Is the monitor ground cont noted | to the monitor?

a : 2. Are the sync inputs ace ed properly?

Picture is upside down: When you serviced. th fe

horizontal or. vertic: v: Use the screens in the Self-test to adjust the procedures i in youl vi eo display manual. Convergenc purity or color probiems. Picture is not centered,

Seat Thumper Problem only quali technicians having experience wi high-po'

s es should troubleshoot this system. The solenoids : andthe | solenoid/motor PCB run on live voltage and can cause serious injury. _ For further information, contact your Atari field service representative at (408). 434-3950.

Page 23

Troubleshooting and Maintenance

Table 3-2 Voltage Inputs and Test Points on the PCBs Voltage... Test Point or LED” Source and Purpose. es +54 0.25 VDC8 4 5V1 ee ey “=>. CR3 LED (Main PCB) CROLED (JSA'll PCB). : CR3LED (SA I PCB). sto oe +VOP ee : a (pin 4 of M324) : cirotitry,: -5V -VOP (pin 11 of L324) “s¢-analog cite Logi ic-power fromthe syten

: =8V from thé Suttching po pol

Maintaining the Coin

Mechanism

The coin mechanism should be cleaned every three months. For detailed parts information on the coin door, see Figure 4-3. To maintain the coin mechanism:

  • Turn power off to the game. Open the upper coin door.
  • Open the gate on the door covering the magnet. Use the blade of a screwdriver to scrape away any metal filings collected on the magnet.
  • Fora thorough cleaning, wash the coin mechanism in hot soapy water. Use a toothbrush to remove any stubborn build-up of residue in the coin path. 4, Dry the coin mechanism with compressed air.
  • If you do not want to use water, brush the loose dust off with a soft brush and scrub the residue in the coin path with a toothbrush. Blow out all the loose dust and dirt with compressed air.
NOTE Never lubricate the coin mechanism with oil or grease.

:

Repairing the Video Display

The video display frame in this game is designed to be used with 25-inch horizontal-mounting displays. Removing the Video Display If you have a problem with the video display, first run the self-test procedure to narrow down the cause. To make adjustments to the video display, unlock the service door on the rear of the cabinet. If you want to repair the video display, remove it from the game by following this procedure:

  • Turn the game power off and wait two minutes. Unplug the power cord for safety,
  • While you wait, unlock the service door on the rear of the cabinet. . Remove the four screws that attach the display shield retainer. Remove the retainer and shield. Then remove the cardboard bezel in front of the display.
WARNING High Voltage The video display contains lethal high voltages. To avoid injury, do not service this display until you observe all precautions necessary for working on high-voltage equipment. X-Radiation This video display is designed to minimize X-radiation. However, to avoid possible exposure to soft X-radiation, never modify the high-voltage circuitry. Implosion Hazard The cathode-ray tube (CRT) may implode if struck or dropped. The shattered glass frorn the tube may cause injury up to six feet away. Use care when handling the display and when removing it from the game cabinet. Also, wear gloves to protect your hands from the sheet-metal edges.

Remove the four nuts and washers that secure the video display. . Discharge the high voltage from the cathode-ray tube (CRT). The display assembly contains a circuit for discharging the high voltage to ground when power is removed. However, to make cestain, always discharge the display as follows: a, Attach one end of a solid 18-gauge wire to a wellinsulated screwdriver or wooden handle. b. Attach the other end of the wire to an earth ground. c¢. Quickly touch the blade end of the screwdriver to the CRT anode by sliding it under the anode cap. d. Wait two minutes and repeat part c.

3-3

Page 24

Troubleshooting and Maintenance Road Riot 4WD

Table 3-3 What bicaiad Problems Look Like Problem ee Program works, but the motion. objects or playfield are wrong. :

Garbage on screen; program doesn't work.

Game program is erratic. 2 No sound or erratic sound. Audio ROM: fe ae ee »-Audio Program Audio ADPCM

6. Disconnect the hamess connectors from the video dis- Steering Control

play.

  • Pull the video display assembly out of the cabinet. Be The steering control is shown in Figure 4-2. If you want extremely careful. to repair the steering control, disassemble it by removing it from the pod on the control panei. The hardware that Replacing the Video Display secures the pod and steering control is shown in Figure 4-1, Perform the following procedure to replace the video display in the cabinet.
  • Carefully lift the video display into the cabinet.
  • Install the nuts that hold the video display assembly.
  • Connect the power and signal harnesses to the video

display. Table 3-4 Atari Games Video

Connector Pin Assignments If you replace the CRT and yoke together, adjust the brightness, size, and centering as described in the video display service manual. Check the purity and convergence according to that manual, but adjust both only if required.

  • Install the video display shield, bezel, and cleats.
  • Lock the rear service door on the cabinet.

Problem. . ie

One terminal (red) is hot, no voltage on the other (black) No:voltage on either terminal Voltage present, but the motor doesn't ““runewhen the left Migger i is s pressed! (while i in Switch “Test)

3-4

Page 25

Steering Motor

The steering motor is shown in Figure 4-2. If you want to test the steering motor, select the switch test (in the selftest) and press the left trigger. This turns the motor on for a few seconds at a time. If you have a problem with the steering motor, refer to Table 3-5.

Foot Pedal Assembly

The foot pedal assembly is shown in Figure 4-3. If you want to repair the foot pedal, disassemble it by removing Troubleshooting and Maintenance

it from the front of the game cabinet. The hardware that secures the foot pedal is shown in Figure 4-1.

ROMs and RAMs

If you have think you have bad ROMs or RAMs, perform the ROM or RAM test in the self-test. If you have a ROM problem, see Table 3-3. If you see only a colored screen and cannot enter the self-test, see Table 3-4. For the location of all the A: ROMs and RAMs on the e game PCB, see Figure 4-6. an

Page 26

Troubleshooting and Maintenance

3-6 oe

dis mie

Page 27

ee

ce ee CHAPTER 4

Parts Illustrations

This chapter provides informa-

tion you need to order replace-

ment parts for your Road Riot

4WD™ game. Common hard-

ware parts, such as screws, nuts,

washers, and so on, are included number of your game. With this

information, we can fill your

order rapidly and correctly. We

hope this will create less down-

time and more profit from your games. ® Atari Games Customer

in these parts illustrations. ® When you Service phone numbers are listed on the

order parts, give the part number, part name, inside front cover of this manual.

the number of this manual, and the serial

Page 28

Parts Illustrations

items Not Shown. ‘049922-01 Lett wee! Decal

0x1 14784, Dr. Secon (eplaces) ‘AOaHO5-07 ‘oad Pot Main Harness Assy. ‘A040490-01 Solenoid Harness Assy. ‘A049496-01| AC Cabinet Hamess Assy. ‘A04S450-01 ‘Shaker Steeting Convo Assy. (2 places) TH369 Foad Rot 4 WD Operator's Manual Tu.330 Wes Gardner 25° Dispiay Manual ‘ST-369 Road Riot 4 WO Sall-Test Label Road Riot 4 WD Schematic Package

Modifies Sea ‘AO49510-01, ‘SolSeat Hamess Assy. “AOt9461-01 Rump Thump Assy.

s7ro2e 9148 1420 Low-Crown Nut (Bplaces) 178225003 +516 Dia. Hole Plug (@places)

7555208 1420 x 1.28 Cartage Bolt (12places) 7507002 ‘Ws Fender Washer (r2places) e072 "1A" Fender Washer (places) 477023-001 ‘4-20 Spring Toggle Wing places) 725520 14-20 x 1.25 Hex Seow (eplaces) 75-0835 45/16 Spli-Lock Washer (replaces) 72-5912 5716-18 x 78 Hex Sc (12 places)

Figure 4-1 Cabinet-Mounted Assemblies, Front View 76025-3420 14-20% 1.25 Hor. Bul Hd. ‘Tamperproot Sere (4 places 1750143050 “vat Fiat Washer (4places)

os9192-01 ‘Atvacion Shield ‘049917-01, ‘Atwacton Decal

049190-01, Display Shiets ‘o49104-01, Display Shitd Retainer 176057-4016| 10.24 x 1.0 Hex Bute, “Tamperproot Sow |

‘18x 12 Double-sied Foam Tape inch)

049198-01, Monitor Mounting Bracket |

“14° SpileLock Washer (12 placa) +175014-1050) ‘Va 281 x 625 Flat Washer|

175018-3050 +14" Flat Washer (15places) 176025-4420 1420 x 1.25 Hex. But Hd. “Tamporproot Ser (@places)

TOD 4-20 Polymer Hex Locknut (12 places)

A049150-01 C -171086-002; 24" Flourescent Lamp Fixture “170003-002| 28,20 Coon

Page 29

a cera | oa Fi 24", 20W Coolwhie Fouresceat Lamp) 178232-001 |

#10518 Pan. Tapaiog Soren plac 139022-401 or 402 25" Sid Res. Well- ‘Gavan Dispay (ode! 2547191), (places) "72-5520, 1420 1.25200 Hox, Screw (Spices) 75-0885 us" ZnSe! Spli-Lock Washor

sar 281 x $25 SteoiZiee Fla Washer

ProguctD.Lanel Let Display Borel ‘ra0se-002 116x172 Double- | o4atas.o1 Steering Brackot (paces) 76025-4432 41420 x20 HexHe. Poy-Leck, Tamperproot

(places)

places) arro10-2e4 114" Locknut (epleces) 17514-3050 ‘ut Fat Washer Buon Cap Screw

9522-02 Fight Atracton Decal

oterse.01 Fightice Decal 17801602, 88x 1/4 Sq, Dr, LPW Sow (places)

| 120060-002 $9, Green START Buton Assy. places) ‘retnaeo01

‘Wood Paton otoszit Seat Pate 72:a08F 2 Pans. Som Snap Switch (places) anas4a604 START Hamness Assy, @places)

o49175.01 Control Pane! oagg21-01 Iratution Decal

04985401 ‘Shaker Steering Cont! (places) 76026-4432

4919501 Speaker Grito pices) areote212 #30 x8 Sq, Dr. Serow (places)

t77000-132 410 en Nut (pices) Srores016 Hee este s Showa xa Pants, Scew Seat Harness Assy. (2places) 11420 x0.75 €-Countersunk-Cap “Tamperproot Scrow (Bplaces) isg1801 ‘Sleeting Control Decal

04382542 Foot Podal Assy

916-20 Hox oiymerLacknut (places)

oei0-01 SeatiCabinet Bracket ‘76025-4432 114-20 x 2.0 Hox-He. Poly-Leck, Tamperpros! Button Cap Screw (16places) 4178014-3050 ‘ye Fat Washer + (16 places)

Figure 4-1 Cabinet-Mounted Assemblies, Front View A049150-01 C Parts Ilustrations

Page 30

Parts Ilustrations

_f& 176195-008 Adjustable Glide (4 places) 1178023-003 4° Swivel Caster (places) (049525-01 ‘75-0458 1/4" Split-lock Washer Goin Door Diser Panel (16 places) -A048503.01 75-0158 ONOFF Assy. +18" Fat Washer 176015-110 94952401 (16 places) #10 x 5/8" Pan-Hd. Screw PCB Mounting Pate 725512 (places, 1420x318 Hex-Hd. Screw (8 places) 725516 116209" Hox-Hd. Screw (8 places a #811114 X-Rec Screw

(4 places)

Figure 4-1 Cabinet-Mounted Assemblies, Rear View A049150-01 C 037332-01 Louvered Grille (2placos) ‘7612-001 Wire Routing Clip 176013212 | #10 x 3/4” Sq. Dr. Pan-Hd. Tapping Screw (12 places)

(049174-01 Monitor Door (2places) 176020-220 #8x 1 114" X-Rec Screw (4pplaces)

/A049501-01 ‘Component Bracket Assy. 176015-110 #10x 516" Pan-Hd. Screw (2places) ‘A046341-01 Coin Counter Assy. (2places) 180084-241 DPOT Slide Switch

‘Component Harness Assy. 178325-008 ‘Cash Box 178326-002 ‘Cash Box Cover 038158-01 Product LD. Label

“Top COMM-RAM op PCB Assy.

A049515-02 Road Riot Board Sat Assy. (2places) 176015-110 #10 x 5/8 Pan-Hd. Screw (2 places) 72-1606F 6-92 x 3/8 Pan-Hd, Sorew (places) 17033-1610 #6 518 X-Reec Screw (4 places) 175014-1025 156 x 312 Flat Washer (6places)

Page 31

Parts Illustratrations

34, 35 (2x) \ 24, 25,26

Side View

14,141

Front View en

NOTE

The parts list for these illustrations appears on the following page.

38 (not shown)

Bottom View

Figure 4-2 Shaker Steering Control Assembly A049454-01 C

Page 32

Parts Illustrations

Shaker Steering Control Assembly Parts List

ItemPart No.DescriptionItemPart No.Description
1049452-01Frame Weldment23:119008-1001 5K Q Po
2049453-01_.156-Inch-Dia.-Hole Counterweight24— 175002-001Large .750-Inch-Dia.-Shaft Washer
3049455-01Cover
4047482-01Shaft Weldment25175005-004.762 x .010 Thick Shim Fiat Washer
26178012-00iRetaining Ring with .750-Inch-Dia. Shaft
5047479-01Pot Bushing27-72-801010-32 x 5/8 Lg Soc Hd Cap Screw
6047488-01Pivot Shaft Torsion Spring,28175002-004#10 .062 Thick Flat Washer
7047485-01O-Ring Stop
8047475-01Centering Plate29177010-24110-32 Polymer Hex Lock Nut

30 —-176041-3608 6-32 x 1/2-Inch Tamper-Proof Button-

9047487-01Spring CatchHead Torx T-10 Screw
10-040241-01Bearing Spacer31106007-001Loctite 290 Green Wicking Adhesive
i171100-001Right-Hand Kit Handle Assembly32177000-1388-32 Hex Nut
12171100-002_Left-Hand Kit Handle Assembly

33-72-8808 8-32 x 1/2 Lg Soc Hd Cap Screw

13047476-01Pot Bracket34106007-001Lithium Grease Lubricant
14 —— 145008-001Motor 12 Vde (Globe)3576-081202750 LD. (Nyliner) Bearing
14.1178311-1008 1/8-Inch Clear Heat-Shrink Tubing36178294-0606 50. Lg Tubing (1 Inch Req'd)

(2 Inches Req'd)

37:178027-001Nyogel 779 Lubricant
17178244-220Hose Clamp38A049462-01Shaker Control Harness Assembly
1872-88128-32 x 3/4 Lg Soc Hd Cap Screw39178068-0021-Inch Sq. Adhesive-Back Cable Tie
19177010-2388-32 Polymer Hex Lock NutMount
20-178181-7806 #8 Clearance LD. x .375 Lg Stee! Spacer40— 178065-1004-Inch-Long Wire & Cable Tie
4172-CT604_6-32 x 1/4 Hex Washer-Hd Screw

21 048861-01 22 178223-006

4-6 X-Y Steering Modified Screw -549 LD. x .103 W (2-133) O-Ring

Page 33

Road Riot 4WD Parts Illustratrations

178012-002 1114" Retaining Ring (04292801 oda! Shaft f 107027.001 178012006 abe o4a827-01 (| “12 Shaft Retaining Ring pean ee jA047963-01 Foot Pedal Harness Assy

_| 178068-002 ‘Adhsv-Back Cable Tie Mat

043826-01 Frame

14° Tie Wrap

1190081001 5K _Potentiometer

NOTE: Lubricate onthe the four bearings.

043691-01 Return Spring 3 7 75-0480 (2 places) #8 Split Lock Washer 78-200032 (2 places) 72-1806F #8-92 x 9/8" Pan-Hd Screw (2 places) 1.75"-Long Spring Sleeve (2 places)

Figure 4-3 Foot Pedal Assembly A043825-02 D

Page 34

Parts Illustrations

99-15025 Coin Inlet, Left 99-15104 Base Plate W/Pivot and Studd 99-5113, 99-15086 Key Hook Coin Mechanism

99-15056 Screw for Bezel “

awe en ee a gj s 99-15096 y Sw. Adjuster

99-15056 Screw

99-15130 ~ y Snap-on Clip

99-15131 Elastic Locknut 99-15132 Snap-on Sleeve

99-15026 Coin Inlet, Right

99-15133, Hold Down Bracket

S P 99-15056 99-15128 . Screw for Bezel

NutWasher for M/S Mounting Screw

99-15056 ‘Screw for Bezel 99-15129 Mounting Stud. (2 places)

99-15028 Coin Ret. Box 99-1505 99-15042 Lamp Holder Switch

99-15126 MIS Flat-Head Mounting Screw aati 99-15085 9 99-15134 99-15029 Coin Door 4-40-1" Pan-

Bracket Hamess Head Screw

Figure 4-4 Four-Entry Coin Door Assembly 171101-001

4-8

Page 35

Road Riot 4WD_ Parts Illustratrations

99-15038) '99-15036 99-15089 ioc heny Bezel for Button! Cover

99-1500% thru 99-15012, Return Button 99-15039 Bezel for Cover a 99-15125 7” Frame Hinge Screw

|99-15135 Frame Clamp Screw

9915114 Die Cast Frame

178325-002 | Goin Box Cover

178325-001 Coin Box Hanger

178325-003, Coin Box

Figure 4-4 Four-Entry Coin Door Assembly, Continued 171101-001

Page 36

Parts Illustrations Road Riot 4WD

4-10

Page 37

‘179231-102 2 Position Terminal Block (2 places) s79zt-004 Torinal Block Jumper (2 places)

  • HAAGOES 4#6-32 x 3/8" Cioss-Rec Screw (4places) (049504-01 Power Supply Chassis Base

eet eee

ecco!

cross Rgs Scrow ‘epaces)

Figure 4-5 Power Supply Assembly A049505-01 B Parts Illustratrations:

© BK Jumper ‘A087728-02 & WJumper A049296-01 P.S. GND Jumper ‘A049506-91 10° BK Jumper

+49014-001 8Y, 7A Hitfon or Petar Chou Power Supply (places) 72-HAA808S 0-92 x38" ‘ross-Rec Screw (places)

+148008-4022 4A, 2504 Siow- Blow Fuse (Ft only) 1146008-3022 4A, 250V Siow- Blow Fuse (F2-F5) 179225-2205 6:Position uso Block 72MAG606S 98-32 x 3/8" Cross-Rec Screw (2 places} 049508-01

  • Fuse Label

4-11

Page 38

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 39

Road Riot 4WD Parts iilustratrations

Road Riot 4€WD Game PCB Assembly Parts List

Desig- Desig-

natorDescriptionPart No.natorDescriptionPart No.
23FSocket, 44 Pin, Plec179237-04423RASIC 65136089-1012
2cSocket, 24 Pin, 300179259-0242ARes, R/2R, 1K/2K118016-001
22, 2SSocket, 32 Pin, .600179257-0322BIntegeated Circuit, 74F374137420-001
3cSocket, 24 Pin, .300179259-0242cIniegrated Circuit, RAM, 2KX8, 35 ns, 3. 137534-001
3KSocket, 20 Pin, .300179259-0202DImegrated Circuit, 7418374137144-001
3P, 38Socket, 32 Pin, 600179257-032aIntegrated Circuit, 74F32137486-001
4/5M, 4M — Socket, Zip 28179302-0282KIntegrated Circuit, 747169137496-001
4P, 48Socket, 32 Pin, 600179257-0322MIntegrated Circuit, 7418377137145-001
5cSocket, 24 Pin, 600179257-0242PEPROM, 200 ns, 128KX8136089-1017
SoMSocket, Zip 28179302-02828EPROM, 200 ns, 128KX8136089-1018
5P, 58Socket, 32 Pin, 600179257-0323/44Integrated Circuit, 7418260187332001
68Socket, 28 Pin, .600479257-0283ARes, R/2R, 1K/2K118016-001
6cSocket, 20 Pin, 300179259-0203BIntegrated Circuit, 74F374137420-001
6P, 68, 7P, 78, 8C, 8D, 8P, 8S3cIntegrated Circuit, RAM, 2KX8, 35 ns, 3. 137534-001
Socket, 32 Pin, .6004179257-0323DIntegrated Circuit, 7418374137144-001
9/10FSocket, 68 Pin, Plec179237-0683)Integrated Ciscuit, 7418377137145-001

9C, 9D, 9P, 95, 10€, 10D, 11C, 11D

Socket, 32 Pin, .6001792570323KGALIOVS, 25 ns136089-1005
3MIntegrated Circuit, 7415157137029-001
11sSocket, 20 Pin, 300179259-020BPEPROM, 200 ns, 128KX8136089-1019
12ESocket, 40 Pin, .600179257-04038EPROM, 200 ns, 128KX8136089-1020
148/CSocket, 64 Pin, 900179256-064
\4FSocket, 24 Pin, 300179259-0244/5MIntegrated Circuit, VRAM, 256KX4, 100 ns 137682-100
4ARes, R/2R, 1K/2K118016-001
15FSocket, 20 Pin, 300179259-0204BIntegrated Circuit, 74HCT273137655-001
15NSocket, 28 Pin, 600179257-0284cIntegrated Circuit, 7418244137038-001
177Socket, 20 Pin, 300179259-20
17NSocket, 28 Pin, 600-179257-0284DIntegrated Circuit, 7418374137144-001
4EIntegrated Circuit, 74F138137521-001
18E, 18}Socket, 40 Pin, .600179257-040EIntegrated Circuit, 7418378137305-001
20/21G, 20/21D, 20, 20D4Integrated Circuit, 74F153137492-001

Socket, 32 Pin, .600 179257-032

20PSocket, 20 Pin, 300179259-0204KIntegrated Circuit, 7415153137104-001
20R/SSocket, 68 Pin, PLOC179237-0684MIntegrated Circuit, VRAM, 256KX4, 100 ns 137682-100
4PEPROM, 200 ns, 128KX8136089-1021
2iL, 21PSocket, 20 Pin, .3004179259-02048EPROM, 200 ns, 128KX8136089-1022

22, 22D, 22]

Socket, 32 Pia, .600379257-0325cIntegrated Circuit, 28C16-200, 200 ns—_-137648-200
22PSocket, 20 Pin, 300179259-9205D, 5EIntegrated Circuit, 741874137023-003
SFIntegrated Circuit, 74F32137486-001
qAIntegrated Circuit, 7406137052-001byIntegrated Circuit, 74F153137492-001
1BIntegrated Circuit, 74HCT2731376550015KIntegrated Circuit, 7418153137104-001
1cIntegrated Circuit, 7418244137038-0015MIntegrated Circuit, Viam, 256KX4, 100 ns 137682-100
1DIntegrated Circuit, 7418374137144-001xPEPROM, 200 ns, 128KX8136089-1023
1EIntegraied Circuit, 7418244137038-00158EPROM, 200 ns, 128KXB136089-1024
yIntegrated Circuit, 74F260137570-0016/7Integrated Circuit, 74F260137570-001
1KIntegrated Circuit, 7418378137305-0016BIniegraied Circuit, ADCOB09137243-001
iMIntegrated Circuit, 7418157137029-0016cGAL16V8, 25 ns136089-1009
223AIntegrated Circuit, 74.8260137332-0010Integrated Circuit, 74F74137436-001

4-13

Page 40

Parts Illustrations Road Riot 4WD.

Road Riot 4WD Game PCB Assembly Parts List, Continued

Desig- Desig-

natorDescriptionPart No.natorDescriptionPart No.
6EIntegrated Circuit, 741874137023-001121, 12N, 12Pintegrated Circuit, 74F169137496-001
OFIntegrated Circuit, 741832137019-00113D/E, 13E Integrated Circuit, 74F04137437-001
gIntegrated Circuit, 74F153137492-00113FIntegrated Circuit, 74F02137481-001
OKIntegrated Circuit, 7418153137104-00113)Integrated Circuit, 74F174137531-001
oMIntegrated Circuit, 7419377137145-00113LIntegrated Circuit, 7418245137134-001
oPEPROM, 200 ns, 128KX8136089-1025,Wi 13P,13RIntegrated Circuit, 74F153137492-001
6sEPROM, 200 ns, 128KX8136089-1026Integrated Circuit, 7418257137136-001
TFIntegrated Circuit, 741886137079-001rcIntegrated Circuit, 68000, 16MHz137669-0001
7Integrated Circuit, 74F153137492-00114D/EIntegrated Circuit, 74F244137502-001
1™Integrated Circuit, 7415153137104-00114FGAL6001, 35 ns136089-1010
7™Integrated Circuit, 7415244137038-00114Integrated Circuit, 74F04137437-001
7EPROM, 200 ns, 128KX8136089-1027MKIntegrated Circuit, 74F00137327-001
78EPROM, 200 ns, 128KX8136089-102814LIntegrated Circuit, 7418245137134-001
8A/BIntegrated Circuit, 74F245,137591-00114N,Integrated Circuit, 74F374137420-001
8CEPROM, 150 ns, 128KX8136089-101314PIntegrated Circuit, 7418374137144001
8DEPROM, 150 ns, 128KX8136089-101414R, 14S _ Integrated Circuit, 74F153137492-001
aKIntegrated Circuit, 74F02137481-0011AIntegrated Circuit, 7418257137136-001
8K/LIntegrated Circuit, 7418153137104-00115B/CIntegrated Circuit, 741574137023-001
8M.Integrated Circuit, 7415244137038-00115CIntegrated Circuit, 7415148137417-001
8PEPROM, 200 ns, 128KX8.136089-102915DIntegrated Circuit, 74F20137530-001
8S,EPROM, 200 ns, 128KX8136089-103015SEIntegrated Circuit, 74F244137502-00i
9/10FFPLA136089-100415FGALI6V8, 25 ns136089-1007
9A/BIntegrated Circuit, 7418245137134-0011SLIntegrated Circuit, 74F153137492-001
9CEPROM, 200 ns, 128KX8136089-1015,15NIntegrated Circuit, RAM, 32KX8, 70 ns, .6 137615-070
15R, 158Integrated Circuit, 74F163137345-001
9D.EPROM, 200 ns, 128KX8136089-101616AIntegrated Circuit, 7418244137038-001
OKIntegrated Circuit, 7497137090-00116B/CIntegrated Circuit, 74FO8137483-001
9MIntegrated Circuit, 747174137531-00116CIntegrated Circuit, 74F163137345-001
oPEPROM, 200 ns, 128KX8136089-1031
16DIntegrated Circuit, 74F74137436-001
9SEPROM, 200 ns, 128KX8136089-103216EIntegrated Circuit, 74F32137486-001
10AIntegrated Circuit, 7418257137136-00116FIntegrated Circuit, 74F138137521-001
10A/BIntegrated Circuit, 7418245137134-00116K/LIntegrated Circuit, 74F153137492-001
10KIntegrated Circuit, 7418378137305-001
16LIntegrated Circuit, 74F00137327-001
10LIntegrated Circuit, 7497137090-00116R, 168Integrated Circuit, 74F163137345-001
11/12A/BIntegrated Circuit, 7418174137122-001VAIntegrated Circuit, 7418244137038-001
AIntegrated Circuit, 7418257137136-00117A/BIntegrated Circuit, 7418197137240-001
11A/BIntegrated Circuit, 7419174137122-001
17B/CIntegrated Circuit, 74F32137486-001
LIK, 11LIntegrated Circuit, 74F169137496-00117DIntegrated Circuit, 74F04137437-001
11NIntegrated Circuit, 7418377137145-00117E,17FIntegrated Circuit, 74F138137521-001
11PIntegrated Circuit, 741S157137029-001WwWGALI6V8, 25 ns136089-1008
11sIntegrated Circuit, 74F138137521-001
17LIntegrated Circuit, 7418245137134-001
124/BIntegrated Circuit, 74F245137591-00117NIntegrated Circuit, RAM, 32KX8, 70 ns, .6 137615-070
1L2C/DIntegrated Circuit, 74F244137502-00117R, 178Integrated Circuit, 74F163137345-001
12FIntegrated Circuit, SOS137550-00118AIntegrated Circuit, 741257137136-001
12KIntegrated Circuit, 74F153137492-001
18A/BIntegrated Circuit, 74F08137483-001
Page 41

Road Riot 4WD Game PCB Assembly Parts List, Continued Parts Ilustratrations

Desig- Desig.

nator _ DescriptionPart No.nator_DescriptionPart No.
18B/CIntegrated Circuit, 7418153137104-001C14-C18Capacitor, 100 pF, 100 V, +5%, Ceramic122016-101
18CIntegrated Circuit, 7418298437201-001C19-C40_—Capacitor, .01 UF, 50 V, +80%-20%,
18EIntegrated Circuit, SOS137550-001Ceramic122002-103
CélCapacitor, 100 UF, 16 V, Electrolytic124008-107
18)Integrated Circuit, PFHS137419-104€42-€57, C59-C70, C72-C149
18LIntegrated Circuit, 7418245137134-001Capacitor, .1 UF, 50 V, +80%-20%, Ceramic 122002-104
18NIntegrated Circuit, 74F374137420-001
18P, 18SIntegrated Circuit, 7418244137038-001C150, C151 Capacitor, 10 pF, 100 V, +5%, Ceramic122016-100

C152-C180 Capacitor, .1 HF, 50 V, +80%-20%, Ceramic 122002-104

19aIntegrated Circuit, 7418257137136-001C181, C182 Capacitor, 100 pF, 100 V, +5%, Ceramic122016-101
19CIntegrated Circuit, 7418298137201-001C183-C244, C246-C252, C254-C262Capacitor, .1
19FIntegrated Circuit, 74F04137437-001BF, 50 V, +80%-20%, Ceramic122002-104
gyIntegrated Circuit, 7419378137305-001

€263-C274 Capacitor, 100 pP, 100 V, +5%, Ceramic 122016-101

19KIntegrated Circuit, 7418163 A137114-001523Capacitor, .1 pF, 50 V, +80%-20%, Ceramic
19LIntegrated Circuit, 74F86137649-001122002-104
19NIntegrated Circuit, 7415374137144-001
20/21CEPROM, 200 ns, 128KX8136089-1041CR1,CR2Diode, 1N4001131048-001
CRDiode, MV5053, Light-Emitting131027-002
20/21DEPROM, 200 ns, 128KX8136089-1038CIRConnector, 2 Ckt, Header, .100179048-002
20/21FIntegrated Circuit, 7418378137305-001
20/21)Integrated Circuit, 7419157137029-001GND1,GND2 Test Point179051-001
20/21KIntegrated Circuit, 7418377137145-001
J4,J9, JlConnector, 2 Ckt, Header, .100179048-002
20CEPROM, 200 ns, 128KX8136089-1042JAUDConnector, 36 Ckt, .1 Header, Long179300-036
20DEPROM, 200 ns, 128KX8136089-1039JPl3Connector, 11 Ckt, Header, .100 Ctr, Key 7 179118-011
20FIntegrated Circuit, 7418377137145-001JSYNCConnector, 3 Ckt, Header, .100 Ctr179048-003
20), 20KIntegrated Circuit, 7418163 A137114-001JxConnector, 60 Ckt, Header, .1X.1C-179291-060
20LIntegrated Circuit, 74F138137521-001LLInductor, 100 HH141024-001
20NIntegrated Circuit, 74F163137345-001
20PPROM136089-1001Q1-Q3Transistor, 2N3904133041-001
20R/SCPU, PLCC336079-2053Q4GHTransistor, 2N5306133033-001
Q‘Transistor, 2N3904133041-001
21FIntegrated Circuit, 7415378137305-001
2iLGALI6V8, 25 ns136089-1006RIResistor, 100 Q, 45%, 1/8 W110027-101
21NIntegrated Circuit, 74F163137345-001RResistor, 15 2, 45%, 1/8 W110027-150
2pPROM136089-1003R3Resistor, 100 Q, 5%, 1/8 W110027-101
R4Resistor, 15 2, 45%, 1/8 W140027-150
22EPROM, 200 ns, 128KX8136089-1040
2DEPROM, 200 ns, 128KX8136089-1037RSResistor, 100 Q, 45%, 1/8 W110027-101
20FIntegrated Circuit, 74F85137685-001R6Resistor, 15 2, +5%, 1/8 W110027-150
225EPROM, 200 ns, 128KX8136089-1046RT-ROResistor, 470 Q, 45%, 1/8 W110027-471
RIOResistor, 2.4 K Q, £5%, 1/8 W110027-242
221,Integrated Circuit, 7418151137101-001
22NIntegrated Circuit, 74F163137345-001RilResistor, 1 K Q, +5%, 1/8 W110027-102
22PPROM136089-1002R12Resistor, 10 2, +5%, 1/8 W110027100
22RIntegrated Circuit, 7418379137374-001RI3Resistor, 2.4 K Q, £5%, 1/8 W110027-242
R14Resistor, 1 K Q, +5%, 1/8 W110027-102
C1-C3Capacitor, 100 pF, 100 V, £5%, Ceramic122016-101
CHC?Capacitor, .1 UF, 50 V, +80%-20%,RISResistor, 10 Q, 45%, 1/8 W410027-100
Ceramic122002-104R16Resistor, 2.4 K Q, 45%, 1/8 W110027-242
C8-Cl1_Capacitor, .01 LF, 50 V, +80%-20%,RI?Resistor, 1 K Q, 45%, 1/8 W110027-102
Ceramic122002-103RIResistor, 10 0, +5%, 1/8 W110027-100

C12, C13 Capacitor, 1000 pF, 100 V, +10%, Ceramic122015-102

4-15

Page 42

Parts Illustrations

Road Riot 4WD Game PCB Assembly Parts List, Continued

Desig- Desig-

natorDescriptionPart No.natorDescriptionPart No.
RI9Resistor, 0.2, 5%, 1/4 W110005-061R17Resistor, 10 K 2, +5%, 1/8 W110027-103
R20-R42Resistor, 1 K Q, £5%, 1/8 W110027-102R118, R119 Resistor, 10 Q, 45%, 1/8 W110027-100
R43-R45, RA, R49-R58R120-R122 Resistor, 10 K Q, +5%, 1/8 W110027-103
Resistor, 470 Q, +5%, 1/8 W110027-471R123,Resistor, 100 2, +59, 1/8 W110027-101
R59Resistor, 1 K Q, +5%, 1/8 W110027-102
R124Resistor, 470 Q, +5%, 1/8 W110027-471
R61, R62Resistor, 10 K 2, +5%, 1/8 W110027-103R125Resistor, 10 K Q, 45%, 1/8 W110027-103
ROS, RGF —_ Resistor, 470 Q, 5%, 1/8 W110027-471R126-R128Resistor, 1 K 2, +5%, 1/8 W110027-102
ROS-ROSResistor, 1 K Q, £5%, 1/8 W110027-102R129, R130 Resistor, 10 K Q, +5%, 1/8 W110027-103

ROO-R72_—_Resistor, 470 Q, 5%, 8 W 110027-471

Ri31Resistor, 100 Q, +5%, 1/8 W110027-101
RY3-R76Resistor, 1 K Q, +5%, 1/8 W140027-102Ri32Resistor, 10 Q, +5%, 1/8 W110027-100
RIT, R78Resistor, 470 ©, 45%, VB W110027-471R133Resistor,1K Q, £5%, 1/8 W110027-102
RIDResistor, 1 K Q, +5%, 1/8 W110027-102R134Resistor, 10 Q, +5%, 1/8 W110027-100
R89Resistor, 220 2, 5%, 1/8 W110027-221
R135Resistor, 1 K Q, $5%, 1/8 W110027-102
R90, ROLResistor, 100 2, 45%, 1/8 W210027-101R136, R137 Resistor, 10 0, +5%, 1/8 W110027-100
ROZ-R1IO)Resistor, 10 K Q, 45%, 1/8 W110027-103R1Z9-RI41_Resistor, 1 K Q, +5%, 1/8 W110027-102
R101Resistor, 240 Q, £5%, 1/8 W120027-241R142Resistor, 470 2, +5%, 1/8 W110027-471
R102Resistor, 100 K Q, #5%, 1/8 W110027-104

R143, R144 Resistor, 1 K Q, +5%, 1/8 W 110027-102

R103Resistor, 10 K Q, 45%, 1/8 W110027-103
Ri05-R107_ Resistor, 1 K Q, 45%, 1/8 W110027-102STESTConnector, 2 Ckt, Header, .100179048-002
R108, R112, R113VCRConnector, 2 Ckt, Header, .109179048-002
Resistor, 10 2, +5%, 1/8 W110027-106WDOGConnector, 2 Ckt, Header, .100179048-002
R1I4-K116Resistor, 1 K Q, 45%, 1/8 W110027-102
x2Crystal, 14.318MHiz144000-004

4-16

Page 43

a 3 OOOH M3403

Figure 4-7 JSA I PCB Assembly A048974-05 D Parts Ilustratrations

Page 44

Parts Illustrations Road Riot 4WD

JSA I PCB Assembly Parts List

Desig- Desig-

natorDescriptionPart No.natorDescriptionPart No.
8DSocket, 16 Pin, .300179259-016Nut/Washer Assy.177026-0036
9C1Socket, 24 Pin, .600179257-024
11¢Socket, 40 Pin, .600179257-040C1,C2,Capacitor, 47 WF, 50V, Electrolytic123015-476
12CSocket, 28 Pin, .600179257-028Cor)Capacitor, .1 uF, 50 V, +80%-20%,

Ceramic 122002-104

12ESocket, 32 Pin, .600179257-032c4Capacitor, 10 UF, 25 V, Electrolytic124009-106
15CSocket, 28 Pin, .600179257-028C5-C7Capacitor, .1 UF, 50 V, +80%-20%,
15SESocket, 32 Pin, .600179257-032Ceramic122002-104
17CSocket, 20 Pin, .300179259-020C8Capacitor, 10 IF, 25 V, Electrolytic—124009-106
17E,19ESocket, 32 Pin, .600179257-032C9,C10Capacitor, .1 WF, 50 V, +80%-20%,
20CSocket, 20 Pin, .300179259-020Ceramic122002-104
C13Capacitor, 47 UF, SOV, Electrolytic123015-476
++1005V1 Test Point179051-00114-C22Capacitor, .1 WF, 50 V, +80%-20%,

Ceramic 122002-104

1DIntegrated Circuit, Quad Op-Amp,C23Capacitor, 10 uF, 25 V, Electrolytic—124009-106

1M3403 137673-001

2AIntegrated Circuit, TDA2030137301-001C24, C25Capacitor, .22 UF, 50 V, £10%, Ceramic 122015-224
3DIntegrated Circuit, 4066B137580-001C26-C28Capacitor, .1 UF, 50 V, +80%-20%,
4AIntegrated Circuit, TDA2030137301-001Ceramic122002-104
4C, 5CIntegrated Circuit, 4066B137580-001C29Capacitor, 1000 pF, 50 V, +10%, Ceramic 122015-102
6D, 6FIntegrated Circuit, Quad Op-Amp,€30-C32Capacitor, .1 LF, 50 V, +80%-20%,
M3403137673-001Ceramic122002-104
7cIntegrated Circuit, 7418273137040-001C33Capacitor, 3300 pF, 50 V, £5%, NFO,
8AIntegrated Circuit, 7418174137122-001+80%-20%122019-332

34, C35 Capacitor, .1 iF, 50 V, +80%-20%,

8DIntegrated Circuit, YM3012137402-001Ceramic122002-104
9C1Integrated Circuit, YM2151137401-001
10AIntegrated Circuit, 7418273137040-001C37Capacitor, 2200 pF, 50 V, +80%-10%,
licIntegrated Circuit, 6502 A137577-001Ceramic122015-222

C38 Capacitor, .1 LF, 50 V, +809-20%,

12CEPROM, 200 ns, 64KX8136089-1047Ceramic122002-104
12EEPROM, 200 ns, 128KX8136089-1051039Capacitor, .015 pF, 100 v, +5%, Poly 126009-153
13AIntegrated Circuit, 741.8240137251-001C40Capacitor, 10 pF, 25 V, Electrolytic124009-106
14AIntegrated Circuit, 7418374137144-001

C41 Capacitor, 1000 pF 50 V, +10%, Ceramic 122015-102

15CIntegrated Circuit, RAM, 8Kx8, 100 ns, 6 137535-004C42, C43.Capacitor, 6800 pF, 50 V,80%-10%,
15EEPROM, 200 ns, 128KX8136089-1050Ceramic122015-682
16A,Integrated Circuit, 7418374137144-001C44, C45Capacitor, .1 HF, 50 V, +80%-20%,
17BIntegrated Circuit, 74F74137436-001Ceramic122002-104

C46, C47 Capacitor, 1000 pF, 50 V, +10%, Ceramic 122015-102

17CGAL16V8, 25 ns, 137646-625136085-1033
WEEPROM, 200 ns, 128KX8136089-1049C48, C49Capacitor, 3300 pF, 50 V, +5%, NPO 122019-332
18BIntegrated Circuit, 741874137023-00150Capacitor, 10 WF, 25 V, Electrolytic124009-106
18CIntegrated Circuit, 7418138137177-001C51-C54Capacitor, .1 WF, 50 V, +80%-20%,

Ceramic 122002-104

19BIntegrated Circuit, 7415393137146-001
19CIntegrated Circuit, 741874137023-001CR1, CR2 Diode, 1N4001131048-001
19EEPROM, 200 ns, 128KX8136089-1048CR3Diode, MV5053, Light-Emitting131027-002
20BIntegrated Circuit, 7415393.137146-001CR6-CR8_Diode, 1N4001131048-001
20CGAL16V8, 25 ns136085-1039CRODiode, MV5053, Light-Emitting131027-002
AGND1Test Point179051-001GND1,GND2 Test Point179051-001

4-18

Page 45

Parts [lustratrations

JSA II PCB Assembly Parts List, Continued Desig- Desig-

natorDescriptionPart No.natorDescriptionPart No.
HS1Heat Sink, TDA2030178190-032R38Resistor, 10 K Q, +5%, 1/8 W110027-103
JAUDConnector, 36 Ckt, .1 Bottom Entry179299-036
Assy, PCB, Surface-Mount (includesR40Resistor, 30 K Q, 45%, 1/8 W110027-303,
MSM 6295 Integrated Circuit)A048972.01R41Resistor, 15 K Q, +5%, 1/8 W110027-153
RAResistor, 150 K Q, 45%, 1/8 W110027-154
R1,R2Resistor, 10 K Q, 5%, 1/8 W110027-103RBResistor, 7.5 K Q, +5%, 1/8 W110027-752
R3Resistor, 33 K Q, 5%, 1/8 W110027-333
R4Resistor,1, +5%, 1/8 W110027-010R44Resistor, 15 K @, +5%, 1/8 W110027-153
RSResistor, 33 K Q, 45%, 1/8 W110027-333RAS.Resistor, 3.3 K Q, 5%, 1/8 W110027-332
RADResistor, 33 K Q, +5%, 1/8 W110027-333
ROResistor, 470 Q, +5%, 1/8 W110027-471R50Resistor, 30 K Q, +5%, 1/8 W110027-303
R7Resistor, 33 K Q, +5%, 1/8 W110027-333
R8Resistor, 1 K Q, +5%, /8 W110027-102R51Resistor, 6.2 K Q, 5%, 1/8 W110027-622
ROResistor, 33 K Q, +5%, 1/8 W110027-333R52, R53_—_-Resistor, 12 K Q, +5%, 1/8 W110027-123
R54Resistor, 7.5 K Q, +5%, 1/8 W110027-752
R10Resistor, 470 Q, +5%, 1/8 W4110027-471RSSResistor, 560 Q, +5%, 1/8 W110027-561
RilResistor, 1 K Q, 5%, 1/8 W110027-102
RI2Resistor, 470 Q, #5%, 1/8 W110027-471R56Resistor, 470 Q, 45%, 1/8 W110027-471
R13Resistor, 1 K Q, +5%, 1/8 W110027-102RSTResistor, 100 Q, +5%, 1/8 W110027-101
RSDResistor, 10 Q, +5%, 1/8 W110027-100
R14Resistor, 470 Q, +5%, 1/8 W140027-471R62Resistor, 15 K Q, 45%, 1/8 W110027-153
RISResistor, 1 K Q, 45%, 1/8 W110027-102
R16Resistor, 470 Q, +5%, 1/8 W110027-471RGBResistor, 10 K Q, 45%, 1/8 W110027-103
R17,R20_Resistor, 1 K Q, 45%, 1/8 W110027-102R64Resistor, 15 K Q, 45%, 1/8 W110027-153
ROSResistor, 7.5 K Q, +5%, 1/8 W110027-752
R22Resistor, 470 Q, 45%, 1/8 W110027-471ROGResistor, 10 K 9, 45%, 1/8 W140027-103
R23Resistor, 33 K Q, +5%, 1/8 W110027-333
R24Resistor, 1 K Q, +5%, 1/8 W110027-102ROTResistor, 3.3 K Q, +5%, 1/8 W110027-332
R25Resistor, 1 Q, +5%, 1/8 W110027-010ROBResistor, 6.8 K Q, +5%, 1/8 W110027-682
ROOResistor, 16 K Q, +5%, 1/8 W110027-163
R26Resistor, 1.2 K Q, +5%, 1/8 W110027-122R70Resistor, 2 K Q, £5%, 1/8 W110027-202
R28BResistor, 10 , +5%, 1/8 W110027-100
R29Resistor, 5.1K Q, +5%, 1/8 W110027-512R71Resistor, 6.8 K Q, +5%, 1/8 W110027-682
R30Resistor, 15 K Q, +5%, 1/8 W3110027-153R72Resistor, 10 K Q, +5%, 1/8 W110027-103
R73,Resistor, 20 K Q, +5%, 1/8 W110027-203
R31Resistor, 10 K Q, 45%, 1/8 W110027-103
R32Resistor, 620 K Q, +5%, 1/8 W110027-624swiSwitch, Slide, SPDT160040-001
R33Resistor, 330 K Q, 45%, 1/8 W110027-334Nut/Washer, Zinc17026-0036
R34Resistor, 82 K Q, +5%, 1/8 W110027-823Screw, Pan-Head, #6-32x3/8,

Cross-Recessed, Cadmium 72-1606S

R35Resistor, 20 K Q, 45%, 1/8 W110027-203Thermal Compound107031-001
R36Resistor, 39 K Q, +5%, 1/8 W110027-393
R37Resistor, 160 K Q, +5%, 1/8 W110027-164

4-19

Page 46

Parts Illustrations

4-20 1s = B FO (020s LS175 Foo F32 a fd alle &

IC6 8 Ic? g (6-2 0 | 0] Ls175 Fao F32 04 [ek [5 5 al] re Foo

Figure 4-8 Comm-RAM (Common RAM) PCB Assembly A049465-01 A

Page 47

Road Riot 4WD Parts Illustratrations

Comm-RAM PCB Assembly Parts List

Desig- Desig-

natorDescriptionPart No.natorDescriptionPart No.
C1-C12Capacitor, 100 pF, 100 V, +5%, Ceramic 122016-101CATCapacitor, .01 LF, 52 V, +80%-20%,
C13Capacitor, 33 pF, 100 V, +5%, Ceramic 122016-330Ceramic122002-103,

cu Capacitor, .1 UF, 50 V, +80%-20%,

Ceramic122002-104C48, C49Capacitor, 1000 pF, 100 V, +10%,
C15Capacitor, 33 pF, 100 V, +5%, Ceramic 122016-330Ceramic122015-102

50 Capacitor, .1 BF, 50 V, +80%~20%,

C16-C18Capacitor, .1 HF, 50 V, +80%-20%,Ceramic122002-104

Ceramic 122002-104

cioCapacitor, 100 pF, 100 V, 45%, Ceramic 122016-101Ic)Integrated Circuit, 74700137327-001
C20Capacitor, 33 pF, 100 V, +5%, Ceramic 122026-330iC2Integrated Circuit, 74LS175137123-001
C21, C22Capacitor, .1 pF, 50 V, +80%-20%,1C3,Integrated Circuit, 74F0O137327-001
Ceramic122002-1041c4Integrated Circuit, 74F32137486-001
C23,Capacitor, 33 pF, 100 V, +5%, Ceramic 122016-330IC5Integrated Circuit, SRAM DP, 2Kx8,
C24Capacitor, 100 pF, 100 V, +5%,55ns, .6137681-055
Ceramic122016-101ICSSocket, 48 Pin, .600179257-048
C25, C26Capacitor, .1 UF, 50 V, +80%-20%,1C6Integrated Circuit, 74LS175,137123-001
Ceramic122002-104Ic7Integrated Circuit, 74F0O137327-001

C27 Capacitor, 33 pF, 100 V, +5%, Ceramic 122016-330

IcsIntegrated Circuit, 74F32137486-001
C28Capacitor, .1 WE, 50 V, +80%-20%,IcoIntegrated Circuit, 74F0O137327-001

Ceramic 122002-104

29Capacitor, 33 pF. 100 V, +5%, Ceramic 122016-330J, j2Connector, 60 Circuit, Rec, .1.x.1C179303-060
C30Capacitor, .1 HF, 50 V, +80%-20%,BConnector, 11 Circuit, Header,
Ceramic122002-104-100 Ctr, Key 2179118-011

C31-C42 Capacitor, 100 pF, 100 V, +5%,

Ceramic122016-101QI, Q2Transistor, 2N5306133033-001
C43Capacitor, .1 WF, 50 V, +80%-20%,R2,R3Resistor, 1 K Q, +5%, 1/3 W110027-102
Ceramic122002-104R4Resistor, 470 Q, +5%, 1/8 W110027-471
C44Capacitor, .01 HE, 50 V, +80%~20%,RSResistor, 1 K Q, +5%, 1/8 W110027-102
Ceramic122002-103RGResistor, 470 Q, +5%, 1/8 W110027-471
C45, C46Capacitor, 1000 pF, 190 V, +10%,R7-R9Resistor, 1 K Q, 45%, 1/8 W110027-102

Ceramic 122015-102

Page 48

Parts Illustrations Road Riot 4WD

a2 2, we cr > z 212.. = Obl SS [naca020 e

CAUTION [7] R7 14 a3 jt Coa 2 a os ce 2 >
2 oH.-veeneee
acia)prs]622e

a a 3 01/1250 at *

tsCAUTION84 u©

3 = PP=20} a 3 S10 — Us RY HAC3010 co a io) = J

Figure 4-9 Solenoid/Motor PCB Assembly A049468-01 A

Parts List

Desig- Desig-

natorDescriptionPart No.natorDescriptionPart No.
HS1Nut/Washer Assy, 6-32, Zinc17026-1036MLConn, 6 Ckt, Har, .250 Ctr179069-006
HS1Screw, Pan, 6-32 x 3/8, Cross-Rec,MJ2Conn, 3 Ckt, Hdr, .250 Ctr179069-003

Cadmium 72-16068 Ql, Q2—Triac, 600 V / 25 A, MAC223A8 133053-001

C1, C2Capacitor, .01 WF, 125 V Rms,Q3, Q4Transistor, TIP120133051-001

Ceramic Disc 120010-103

3Capacitor, 3300 LF, 25 V, Electrolytic 123003-338R1,R2 _ Resistor, 330 Q, +5%, 1/8 W110027-331
R3Resistor, 39 Q, +5%, 1/2 W110001-390
CRI, CR2 Diode, 1N5401131051-002R4Resistor, 270 Q, +5%, 1/8 W110027-271
CRS, CRO Diode, MR822131019-001RSResistor, 39 Q, +5%, 1/2 W110001-390
HS1, HS2_ Heat Sink, TO-220, 15X.5178190-124RO, R7Resistor, 330 Q, +5%, 1/8 W110027-331
HS2)Nut/Washer Assy, 6-32, Zinc177026-1036RBResistor, 270 2, +5%, 8 W110027-271
HS2)Screw, Pan, 6-32 X 3/8, Cross-Rec,R9, R10Resistor, 1 KQ, +5%, 1/8 W110027-102

Cadmium 72-1606S

Ul, U2Opto-lso, Triac, MOC3041138008-001
yiConnector, 11 Circuit, Header,HS1, HS2 Thermal Compound107031-001

-100 Ctr, Key 2 179118-011

11,12Inductor, Ferrite Bead, N12N141003-005,

4-22

Page 49

Road Riot 4WD Statistics Sheet

Date Recorded: Location:

Meter:

Statistics Screen

Left Coins:

Right Coins: Auxiliary Coins: New Games:

Continuation:

Free Games:

Idle Time:

Active Time:

Solo Time:

Linked Time:

Shaker Time:

Thumper Count:

Error Count:

Total Credits:

Total Coins: PPT TPE

Page 50

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 51

Teele eel eel el ella el eel ele fel el pel el pelel el fel el pel fel fel

Warranty

_ Seller warrants that its printed-circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its video displays and laser-video disc players (in games supplied with displays and video-disc players) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment. None of the Seller’s other products or parts thereof are warranted. If the products described in this manual fail to conform to this warranty, Seller’s sole liability shall be, at its option, to repair, replace, or credit Buyer’s account for such products which are returned to Seller during said warranty period, provided:

  • Seller is promptly notified in writing upon discovery by Buyer that said products are defective;
  • Such products are returned prepaid to Seller’s plant; and (©) Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation, or improper testing. In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages.

Except for any express warranty set forth in a written contract between Sell-

ex and Buyer which contract supersedes the terms herein, this warranty is

expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller's part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products by Seller.

The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to you and others. Be very cautious in using non-Atari-supplied components with our games, in order to ensure your safety, Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories, Atari Games Corporation cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor.

Page 52

ae