Zektor
Zektor (revision B) (Sega, 1982) · Manual · 157 pages · 42 sections · original scan
a in
Owner’s Manual
Manufactured By SEGA /Grenln Technology the Cause... -Enteralnment the Effect.
TLX 910-335-1621
ZEKTOR OWNER’S MANUAL Copyright ©1962 by SEGA/Gremlin, All Rights Reserved
TABLE
Introduction. . 2... ee
Game Set-Up and Inspection .
Game Concept... -. 2...
Options Selection . 2... .
Self-Test 2... ee eae
G-80 Bus Detail ..-..-
Troubleshooting Procedures .
Circuit Description ....
Monitor Block Diagram ... OF CONTENTS
Adjustments and Specifications ....- 2.
Parts Latalog . 6... eee
Schematics»... wee
INTROOUCT JUN
ZEKTOR is a microprocessor hased coin-operated electronic game, that makes extensive use of digital integrated circuitry and television monitor concepts. This manual is designed for the use of the maintenance technicians who possess a general working knowledge of solid-state circuitry and video monitor theory. Any individual NOT knowledgeable in these areas SHOULD NOT attempt repair of tne electronic portions of the game.
In addition to this manual ana training in electronics, troubleshooting and repair will be facilitated by: access to general electronic type handtools, a multimeter, a 50 to 100 Mhz oscilloscope and a logic probe would be helpful.
Technical assistance is available by calling (800) 854-1938. Questions or comments concerning ZEKTOR or any of our games are welcome and should be directed to:
Technical Editor SEGA/Gremlin 16250 Technology Drive San Diego, California 92127
GAME SE I-UP AND INSPECTION
- Inspection
- Before plugging in your new game, inspect it cli 2ly to spot any possible shipping damage. Check to ensure the graphics are in place, the monitor is not damaged and that the overall cabinet is in good condition.
- Open the coin mechanism door and inspect the inside of the game electronics Compartment. Be sure no Components or connectors have come Joose. Proper connector fittings must be checked before game power is applied. Check all related connectors for good contact. Although disconnected connectors arc easily spotted, poor contacts are difficult to locate. The connectors should therefore be pushed in firmly and then loosened to spot poor connections.
- Check to ensure the fuses are intact. There are five fuses (not counting the monitor fuses which are detailed in the monitor manual for this game). One fuse is located on the AC junction box. The other four are on the power supply PC board.
- Voltage Selection
Before plugging in your game, make sure that the game voltage is correct for your location. Locate the two leads from the AC junction box to the power transformer. For 110 VAC, they should be connected to terminals 1} and 3 on the power transformer. For 100 VAC, connect 1 and 2, and for 220 VAC applica~ tions, they should be connected to 1 and 4. You will also notice on the AC junction box that there is a safety interlock switch. When the front panel 1s in place the switch is depressed and the game receives power. Removing the front panel, the switch returns to its original position and the power is cut off from the game. For servicing, this switch can be pulled out and power
will be restored.
- Game Specifications
Power 100 VAC, 60HZ (nominal), 150 watts maximum
- Game Specifications (Cont)
Power 110 VAC, GOIZ (nominal), 150 watts maximum 220 VAC, 6OHZ (nominal), 150 watts maximum
Dimensions 25-1/2 inches wide X 30-1/4 inches depth (64.8 cm wide X 76.8 cm depth) 72-1/2 inches height (184.2 cm height)
4, Important Notes
- The following note is included in compliance with FCC rules:
may Cause interference to radio communications. As temporarily permitted by
regulations, it has not been tested for compliance with the limits for Class A Computing devices pursuant to Subpart J of Part 15 FCC Rules, which are designed to provide reasonable protection against interference in which case the user at his own expense will be required to take whatever measures may be required to correct the interterence.
- Miscellaneous
NEVER remove circuit board connections while power is on.
NEVER replace any components with anything other than exact replacement parts.
DO NOT replace fuses with anything other than proper value. A blown fuse indicates an overload condition within the game. Replacing the fuse with a higher value can cause damage to internal components, if an overload occurs.
- Control Pane} Removal
With the door to the game electronics compartment open, disconnect the control panel harness, reach under the control pane? and flip the fasteners on
both cides of the control panel, The contro} pane! will now swing outwards. Slide the spring-loaded pins on both sides and remove the control panel.
- Front Plexiglass, Interior Graphics and Graphics Frame Removal
The front plexiglass, which secures the interior graphics, is held in place by the control panel. Release the fasteners on the control panel and swing it down. Directly under the front plexiglass, you will notice a small frame support piece. Grab it by the hand slot in the middle and pull it from the game. The front plexiglass can now be removed easily by lifting it on the bottom slightly and pulling it outward. The interior graphics can now be removed. You will also see the graphics frame. which is Tocated directly behind the interior graphics. It must be removed when taking out the monitor. To remove the graphics frame, simply grip two sides and carefully iift out.
- Card Cage Removal
If it is necessary to remove the card cage for servicing, first disconnect all the connectors. Then remove the three mounting screws, located on the front bracket. The card cage can now be slipped from under the rear bracket and rewaved from the game.
- Logo Panel Removal
Underneath the logo panel are four mounting screws. Remove these and the logo panel can be lifted from its slot. With the logo panel removed, easy access is gained to the speaker and fluorescent lamp assemblies for servicing.
- Monitor Removal
To remove the monitor for servicing or replacement, first open the rear panel on the cabinet and disconnect the power cable and video cable to the monitor. Then, remove the front plexiglass, interior graphics and graphics frame as explained earlier. Remove the four bolts in each corner of the monitor board. Now grasp the board by the hand holds provided at top and bottom and pull the monitor from the front of the cabinet.
GAME CUNCEPT
ZEKTOR is a one or two player game that tasks you with the liberation of eight cities that have been seized by the evil cadre of alien robots. In order to liberate a city, you must defeat 3 attack waves of Fighters and Robo-probes. Fighters and Robo-probes are often shielded (in red), and each consecutive hit reduces the enemies shield strength, until, when the shield drops, a hit will destroy it. in addition, you will encounter three types of Moboids;
Green Mubotds spin the players snip on contact, and bounce enemy ships.
Blue Moboids bounce all ships.
Red Moboids destroy all un-shielded ships (including the players ship).
After defeating three attack waves, the Alien Robot holding that city will reappear within rotating protective rings, through which a "slot shot" neutralizes that Robot, awarding the player a bonus ship and advancement to the next round.
Each round consists of the three attack waves (sub-rounds), which are scored as follows for each enemy ship destroyed:
Rounds 1 & 2
sub-round | 200 pts. sub-round 2 400 pts. sub-reund 3 800 DLs.
Rounds 3&4
sub-round 1 400 pts. sub-round 2 800 pts. Sub-round 3 1600 pts.
Rounds 5 & 6
sub-round 1 600 pts. sub-round 2 1200 pts.
Sub-round 3 2400 pts.
Rounds 7 & 8
sub-round 1 800 pts. sub-round 2 1600 pts. Sub-round 3 3200 pts.
Game play ends with the loss of the last player ship.
OPTION
UPRIGHT
COCKTAIL
VOICE DURING ADVERTISING
NO VOICE DURING ADVERTISING
5 SHIP GAME
4 SRIP GAME
3 SHIP GAME
2 SHIP GAME
GAME DIFFICULTY: HARDEST
HARD
MEDIUM
EASY
OPTION
4 COIN/? CREDIT
3 COIN/1 CREDIT
2 COIN/] CREDIT
1 COIN/CREDIT
1 COIN/2 CREDIT
1 COIN/3 CREDIT OPTION SELECTION
SWITCH #1
1 2
x x
x x
Xx x x x
x Xx
x x
x x
x x
Xx Xx Xx x x x
x x
SWITCH #2
1 2
c c
c c
Cc c
Cc C
C 0
c 0 ><
> > > OK
aaeoeo > > > OK
oon ”e ><
anos
>< > pe OK pe
aon°o
<>< > OK °
>< oe KO
<> OK OK <><
pe oe de OK
Oe
OPTION SWITCH SETTINGS - (cont. }
OPT ION SWITCH #2
| 1 | 2 | 3 | 4 | 5 | |
| 1 COIN/4 CREDIT | c | 0 | 0 | ¢ | Cc |
| 1 COIN/5 CREDIT | Cc | 0 | 0 | 0 | ¢ |
| 1 COIN/6 CREDIT | oc | cc 8 | |||
| 2 COIN/1 CREDIT | 09 | ¢ | Co | oO |
4 COIN/2 CREDIT 5 COIN/3 CREDIT
~
| COIN/1 CREDIT | 0 | c | 0 | c | 0 |
4 COIN/3 CREDIT
| COIN/1 CREDIT | 0 | c | 0 | 0 | 0 |
COIN/2 CREDIT 3 COIN/3 CREDIT ~
| 4 COIN/4 CREDIT | 0 | c | 0 | 9 | o |
5 COIN/6 CREDIT
| 1 COIN/1 CREDIT | a | fa) | c | c | i) |
2 COIN/2 CREDIT 3 COIN/3 CREDIT 4 COIN/S CREDIT
| 1 COIN/1 CREDII | it} | 0 | Cc | 0 | 0 |
2 COIN/3 CREDIT
| 1 COIN/2 CREDIT | 9 | 0 | 0 | ¢ | 0 |
2 COIN/4 CREDIT
OPTION SWITCH SETTINGS ~ (cont.)
OPTION SWITCH #2
1 2 3 4 5 6 7 8
3 COIN/6 CREDIT 4 COIN/8 CREDIT 5 COIN/11 CREDIT
7 COIN/2 CREDIT 0 0 ie) 0 0 0 0 0 2 COTN/4 CRENTT 3 COIN/6 CREDIT 4 COIN/9 CREDIT
co = NOT USED 0 = OPEN € = CLOSED
ing SELF-TEST
The G-80 system contains a built-in self-test system, activated by depress-’ the red self-test switch located on the CPU Board. If the cover to the G-80 card cage is in place, the switch can be activated by putting a pen or penc1l through the hole provided on the cover.
10. Basic diagnostics test sequence:
CPU RAM
Maskable interrupts
First 1K of game ROMs
Video RAM and Hardware multiplier
Player start buttons
Display screen (visual)
All game ROMS
System inputs
Game controls
Sounds/Vo ice
Individualized diagnostics descriptions and procedures:
CPU RAM - tests all RAM on CPU card before proceeding, system needs to use this RAM for stack and variables during other tests so if any locations are bad, processor will halt (halt light will come on).
2, Maskable interrupts - video interrupt is enabled through output port bit and all maskable interrupts are enabled inside processor, CPU then executes several HALT instructions to insure that at least one edge triggered interrupt has occured. If no interrupts occur during this test the halt light will remain on constantly. This is the same result as a bad CPU RAM. This ambiguity can be eliminated by checking the vertical interrupt another way. The system reset/power-up logic wil? also halt if the video interrupt is not functioning, to try this press the RESET switch.
- First 1K of game ROMs - the first IK of the first game ROM will be checked for validity. If this portion of the first ROM is bad the system will not be able to proceed because vital information defining parameters of the game are stored in this first IK. If an error occurs during this validity check, the CPU will lock up and repeatedly flash the halt light.
- Video RAM and Hardware multiplier - the video RAM is tested first and in the event that it tests good then the hardware multiplier is checked. If the video RAM is good, the message “ALL VIDEO RAM GOOD, MULTIPLIER GOOD" appears. If a bad video RAM chip is found, then the message "BAD VIDEO RAM, CHIP UF#" appears on the screen along with that chip's location, Due to the fact that sometimes a bad video chip causes the display to be erratic, the system also flashes out the bad chip's location on the halt light, over and over again separating the U#s with a one second on pulse.
The hardware multiplier is used in the game to multiply two 8 bit numbers together to form one 16 bit product. This test performs a select group of multiplications, over 2,000 multiplications in actuality, designed to thoroughly exercise the process of multiplication between the software and the hardware multiplier. The messages "GOOD" or "BAD" are the only indication of
functionality with respect to this test.
- Player start buttons - one of the twa "game start" push buttons on the front of the cabinet is very special. The “one player start" button was designated by the system as a way to terminate the test that is currently being run. The reason that these two buttons were tested relatively early in the sequence, was so that the remaining tests could use the “one player start"
chi
button for a termination signal. To be sure thal these two buttons are tunctioning properly, see that when untouched the status indicated is "0" (for open switch contact) and that when pushed or depressed momentarily the indicated status is "C" (for closed switch contact) during the time the button is down, This notation for switches being in the open or closed state, "0" or “C", will be used throughout the diagnostic sequence whenever the status of a switch is being displayed on the screen.
- Screen - this test is supplied by the game logic, external to the CPU ROM, to provide a visual indication of how well the display streen 1s Tunctioning. It tests beam deflection and colors to check that all electron guns are func~ tioning. In the display, you should see some sort of test showing the colors white, red, green and blue.
- All game ROMs - the intent of this test was to insure the integrity of all of the data in all of the game ROMs. At the time the ROMs for a game were originally generated there was an algorithm performed on each IK block of data. Each of these calculations, a form of CRC (cyclic redundancy check, similar to a checksum), produced one 16-bit word. These words are Stored, along with a Gremlin part number, in the first ROM. When this test is run, all of these 16-bit CRC words are regenerated and are compared to the known values stored in the table in the first ROM. If one of these newly calculated values does not match its corresponding stored value, then the system kicks out an error which amounts to the message "BAD ROM" followed by one or more bad part numbers of that ROM that was found in mis-match. If al] ROMs are good the screen displays: "ALL ROMS GOOD". Then the system quickly proceeds on to the next test.
- System inputs - these inputs are referred to as ‘system inputs', simply because they control system functions, such as credit accumulation, coinage options, game configuration, etc. The diagnostic user may check to see that the coin switches, service switch, and option dip switches are functioning properly. The open and closed switch notation applies here as described earlier.
- Game controls - the names of the controls that the game player would use to contro] the action on the screen is what this test was designed to check. Make sure that when hands are off of the controls ali of the switches are open.
When a particular control is twisted, pushed, turned or in whatever way aclivaled, watch Lu see thal Lie slalus of that control, and only that particular control, changes to reflect the action on the contro] panel. The screen should display from open to closed.
- Sounds/Voice - just sit back, listen and watch this one. All of the sounds made by the game will be produced and their respective names will appear in the center of the screen. The termination button acts sluggish during this test due to the fact that some of the sounds must be created by subroutines external to the CPU ROM. After completion of this test, the system will return to the advertising mode.
G-80 Bus Detail
TolFrom Coin Mechanism/Game Controls To RGB Monitor or X-Y CRT
To Sound Amplifier/Speacer T Z80A 4Mhz
Sound and
ite Beard Speech Oto2
ith Game Beards Expansion Slots
And Coin (1 or2 slots) On Mother Board
16 Bit Address Bus
iystam Controf Bus
G-80 Bus
ZEKTOR TROUBLESHOOTING PROCEDURES
ZEKTOR is a “state-of-the-art” electronic microprocessor based, video game.
The result of hundreds of hours of work, design, research, experiment and more work. However, as with any electronic device, component failure or other problems can result in a game that doesn't function properly, or doesn't function at all. In either case, your game is "down", and so critically, are your profits.
Your objective is to fix it as quickly as possible, and logical troubie-
shooting goes a long way toward that repair. Although many troubleshoot ing
methods may be familiar to you, procedural logic is common among them, and might be stated in this order: visual inspection, symptom recognition, symptom isolation, function isolation, component isolation and repair. Familiarity with the equipment in question will allow you to bypass one or more of these steps. as any particular problem may be obvious to you, or may have happened before. In general though, these 6 steps form a good premise upon which to
approach your "down" game.
An extremely important item in our procedure is the first mentioned, giving the gear the “once over". A large percentage of failures found in electronics, show themselves visually and often a great deal of time can be saved by inspecting for burnt or blown components, loose or disconnacted wiring or connectors, or PCB traces burnt or pulled up. Thorough visual inspections become increasingly important the closer you get to the faulty item, and should be repeated each time another portion of the game is eliminated. Symptom recognition (as with all electronic troubleshooting) in your game depends first, on knowing what a proper display is, and second, knowing how your display differs from a normal one. Symptom isolation follows naturally; (i.e., "IT have no picture", "I have no sound", “I have no Control over Lhe car", “the picture is scrambled"), ergo, a video, audio, input or logic problem, Function isolation, such as a sync problem with the video, requires that you consider those functions that go to make up video sync. Is it a monitor problem, or an “on-the-board" problem? A monitor input check to verify the signal will tell you. Does the board have the voltage (from the power supply) that it needs? Yes? We must have a board failure, as we've just isolated down to function.
Taking our sync problem further, before we begin our search-for an individual component, let's reapply that first item in our "Logical Troubleshooting Procedure". Look at the board. Open resistors, diodes, and capacitors often give themselves away.
Noticing a trace literally burned open can save you serious "down-time". The board looks OK, so on we go. Specific compunent isulaliun relates to the specific nature of the failure, component commonality, proper inputting (both signal and power) and proper outputting (as in the case of an output held high, low, or floating by input port failure in the succeeding state). More general problems (such as a total loss of video sync) requires the more involved Procedure of systematic elimination of possibilities. This operation can be expedited however, by dividing the circuit in half, establishing a "go-no/go" at that point, and again dividing the suspect circuit portion in half. The largest possible areas can be eliminated in this manner, dividing and subdividing until the individual component failure is found,
As we've outlined previously, any electronic repair procedure consists of a series of efforts to isolate a problem down to a “managable" level; restating our Logical Troubleshooting Procedure in 6 steps, 1. Visual Inspection, 2. Symptom Recognition, 3. Symptom Isolation,
- Function Isolation, 5. Component Isolation, and 6. Repair.
In our ZEKTOR game system, we are dealing with, essentially, 3 major functional components:
- The Power Supply
- The G-80 Boards (Card Cage Module) 3, The Color X-Y Monitor
So, in a typical maintenance procedure, having isolated down to Function (Step 4.), we would next attempt to determine which of the 3 major elements is defective. In the following paragraphs, we will look at each element and some of ils sub-divisiuns a> a yuive in isulalbing furtier.
Usually, the power supply can be eliminated as the source of a problem if the games comes up on the screen. The major exception is when the game plays normally but no sounds are produced. In this case, the power supply'’s amplifier circuit should be checked for audio signals from the sound and speech boards. If they are present on the amplifier output, then a bad speaker or connection is probably the cause of the problem. If the signals are not there, suspect the amplifier circuits on the sound and/or speech boards.
If the picture does not appear on the screen, cneck tne power supply fur the main AC voltage to the primary of its transformer; then ensure that the G-80 boards are supplied with the correct MC valtages from the power supply. Also make sure the 3 VAC reset signal is being applied to the CPU board. If all these tests prove normal, then eliminate the power supply as cause of the problem and proceed to check the remaining functional game components - G-80 boards and monitor.
In most cases, a simple test will help to isolate a problem of no picture to either the G-80 boards or monitor. On an oscilloscope, look for varying voltage signals on pins 1 and 4 of the 4-pin Molex connector on the Timing Board. If the signals look similar to those shown in Figure 1, check for signals swinging between 0 and +4 volts on the RGB outputs (4-pin Molex connector pins 4, 1, 2 respectively) on the Control Board. If all three outputs are at 0 volts, suspect the X-Y boards. If the signals appear normal, suspect the monitor as the cause of the problem. If however, pin 1 (to the monitors horizontal input) is held at or near +4 or -4 volts DC, suspect one or both X-Y boards. If pin 4 (to the vertical input) is held at or near +3 or -3 vOIUS, SUSPECT Tne Other G-8U DOaras. In either case, TURN OFF THE POWER AND IMMEDIATELY DISCONNECT THE X-Y MONITOR. Proceed to check the inputs to 0/A converters Ul and UA (TS) for active signals. Verify that none of the Character Data lines (CD0-CD7) are pulled high or low, or are floating. Check for the XCL and YCL clock signals from U28 (16). Verify that the 15 MHz crystal clock is operating and that a 40 Hz signal is present on pin-11 of U13 (17). Check BOS signal to be sure it is not held; signa? DRAW should be switching high and low. On the Control Board, observe the signal FETCH to ensure it pulses high and low. Also, none of the Data lines (DO-D7). should be held high, low, or tloating (Ub). Check tor clock Signals PCC ang-SCL (C5)-
Look for input changes on U1 and U5 of the color circuit (C6); also, pin-3 of U4 should be active high and low. (See figure 1 in the illustrations section).
When the monitor is suspected of a problem, check for al? correct power supply voltages as shown in the schematic. Isolate incorrect voltages to either the monitor power supply or to the circuit receiving the valtage.
Check the transistors in the color drive circuits for shorts or opens when one or more colors is missing from the display, and the 6-80 boards are known to be good.
COLOR X-Y MONITOR AND 6-80 CIRCUIT DESCRIPTION
To begin our discussion of the Color X-¥ Monitor, let's first pay tribute to the “other kind of monitor" - the raster-scan, As you may remember from your knowledge of raster-scan displays (like those in a TV), that the electronbeam inside the tube always moves in a predictable way. That is, it always starts at the top left of the screen and scans across it, forming a pattern of horizontal lines an the inside surface of the tube as it moves downward. When it gets to the bottom, the beam is forced back to its starting point and
repeats the raster-scan movement. To create a simple display (for example, a large "+" symbol) on the raster-scan monitor, we figure out first, where we want it to appear on the screen; let's say the center, in this case. Then we generate a video signal that represents the "+", plug the Signal into the monitor, and we get a "+" on the display. What we have done is intensify the electron-beam so that only thuse points corresponding to the "+" light up on the raster. (To see how it would look close-up, refer to figure 2 in the
illustrations section. )
Notice how the vertical line is not much of a line, but more a column of stacked lines. This occurs because the raster lines, which run horizontally inside the CRT, are spaced slightly as the beam traces them. So what we see, looking at our line from top to bottom is a tiny segment of the lit up raster, then a black space, another lit up segment, another black space, and so on. Now the horizontal line of our Figure is perfect, one solid, lit up line Corresponding to that particular “raster". The fact that you can't get high- Quality traces in hoth directions is what led to the development of the X-¥ Monitor. If we create that same centered "+" on an X-Y display, we would see two perfect, solid lines - no gaps anywhere. (Refer to figure 2.) What Produces the high-quality, solid lines in any direction in an X-Y monitor is the electron-beam inside the CRT (there are actually three electron-beams, one for each of the three colors, red, green, and blue, although it is often simpler to think of it as one beam). Unlike the beam in a raster-scan unit, the X-Y beam van be moved in any direction we choose. All we have to do is determine where we want to move it. We also need to tell the beam when to turn on, or intensify, to "draw" the design we want, how big tu make the
design, what color the lines should be, what angles the lines will take, and
when to stop drawing. For now, remember that we are directly influencing the X-Y beam to create our lines by moving it and turning it on when necessary; in”
the raster-scan, all we had to do was turn on the beam at the right times.
Before we delve into the circuits that make up the color X-Y monitor, let's consider how we aclually control an electron-beam. Inside the picture tube neck, there is a piece of metal called a cathode. When it is charged with a voltage, it generates electrons. As the electrons are emitted, they are shaped to form a thin ray, or beam, that strikes the front of the monitor. The only way the beam will move up or down, left or right is if a magnetic field is applied around the beam. This is what the deflection coils located around the CRT neck do. There are two coils, one to move the beam up or down (VERTICAL DEFLECTION COIL) and one to move it left or right (HORIZONTAL DEFLECTION CUIL). So, by running some current through either coil, we Create a magnetic field around the beam to deflect il in any direction. The larger the current we put through either coil, the stronger the magnetic field and the more the beam will deflect.
While we're on the subject of beam movement, consider why this monitor is called an "X-Y monitor". Picture our "+" symbol on the screen again; the horizontal line is catled the "X" axis and the vertical line is the "Y" axis, hence "X-Y monitor". Make a mental note that when we move the beam horizontally, we are moving it on the X-axis; moving the beam vert ically occurs on the Y-axis. Let's look cluser at the color X-¥ monitor circuits and see where this deflection coil current comes from. (For the following explanation, please refer to the schematic of the monitor in this manual.) The circuitry primarily consisting of IC 600 (15-2156-01) accepts two varying voltage levels. one for Vertical, one for Horizontal, from the G-80 boards. These
voltages are called ANALOG signals because they represent all voltage leveis between two pre-determined levels.
jet's cay that wa want an analog signal that can vary between two voltages, +3 and -3 volts. We could control it to look like this on an oscilloscope:
° cy
As the signal changes, it moves through all possible voltage jevels that exist between +3 and -3 volts. Don't confuse this type of signal with a digital one. The digital signal switches between 0, and typically, +5 volts. It does not drop to a negative voltage level. As these varying voltages come into the X-Y monitor, they activate, first the Input Driver, intended to set a proper reference, and the X and Y power amplifiers (Q 600-606, Q 700-706). These amplifiers contro] the current that tlows into the X and Y deflection coils, depending on the voltage levels on the inputs, and the input current set by Limitors Q 201, 202, 251, 252. Remember that this current controls the electron-beam movement, so if we vary the input voltage, we vary the output current and the direction of the beam. The following chart will clearify this:
INPUT VOLTAGE BEAM MOVEMENT
Y-AMP Positive Up
(Vertical) Negative Down
X-AMP Positive Right
{Horizontal) Negative Left
Earlier, we said that there has to be a way to turn on, or intensify the electron-beam to create an image on the screen. Well, there are three more inputs to the X-Y that allow us to do just that; they are the color inputs R,G,B and they accept analog signals from the G-80 hardware. These color
signals activate the three color electron-beams through the circuits in the Video PCB. Using what we know so far, let's apply it to an actual example of drawing something simple on the screen - a white line for instance. (Refer to. figure 4 - illustrations section.)
Point A, the center of the screen, is the starting point for the electronbeam. To move the beam to point B, we have to supply voltages to the monitor’ inputs that cause the beam to move at a 45 degree angle. To do that requires two increasing positive voltages on the herizontal and vertical inputs. (See the chart above). Not only are these voltages positive im this case, they also have to be equal. And if they are equal, the deflection coils will force the beam the same distance both upward, and to the right, at the same time. Moving at any other angle is just a matter of making one coil deflect more or less than the other. Again, notice tnat botn coils force beam def tection simultaneous ly.
Since we don't want this 45 degree line to show up on the screen, we don't feed any voltagos to the RGA inmits. Rut, we know the beam is at point By awaiting further deflection. Now, we cause the voltage on the norizontal (X) input to go negative and leave the vertical voltage where it is, Also, we turn on the RGB inputs to give us a white line. From the chart, you can see that these voltages will cause the beam to move to the left, horizontally, to point C. Our line is complete, and here is what our input stgnals looked like
during this process:
+V Horizontal (X} Voltage o -V +V
Vertica) (Y) Voltage
In our example, we made a very short line, considering we could have drawn one clear across the screen, In order to draw longer lines, in any direction, we simply increase the positive or negative voltage on the inputs. Remember the higher the voltage, the more the deflection, the longer the line.
The remaining circuits in the monitor are a power supply, a CRT and brightness contro] (CRT PCB}, and high voltage generator. Here are Functional Black.
and Signal Flow diagrams for the Color X-Y Monitor:
‘ScMunirie
INPUT DRIVER
Q 800-803
Q 600-604 Q 700-704 Q 400, 401
COLOR X-Y MONITOR
MODEL G08-003
X-AXIS CURRENT LIMITER
4] XIN 11 REF
- REF P 200
Q 201
4] Y our 7] REF 7| REF P 251
Q 251 Q 252
4)YIN
- REF 7 | REF Y-AXIS CURRENT LIMITER VIDEO PCB
Q 100-105
HV. REGU- LATOR Q 920-020 +9.1VDC -9.1VDC GND GND NOT USED ic fe] + 12AVNC IN va2 [-}__f3}] + to0vpe our
Refering back to the monitor schematic for the following discussion, the circuitry in block A serves two purposes. First, it compensates for a type of distortion known as the pin-cushion effect. This occurs because the electronbeam must travel a greater distance when striking the edges of the CRT than when it hits the center. If we cause the beam to trace along the edges of the CRT, the beam would draw a box with its left and right sides bowed inward. To
compensale for the effect, this circuit offsets the point where tne beam would normatly strike the CRT surface.
Secondly, this circuit contains two error amplifiers, one for the horizontal and one for the vertical inputs. Each error amp has two inputs; one is set to zero volts, the other accepts the analog signal from the G-80 system, sensing current movement in the deflection coil. The analog signal is allowed to pass through the error amps and drive the deflection (power) amps. The deflection amps are shown in blocks B and F, The outputs of the X and Y power
amps pass Current through their respective deflection cofls. The output leads of the two coils are connected back to the analog inputs of the respective error amps, as mentioned above. This acts as an error, or feedback, signal and ensures that the current through the deflection coil remains proportional to the voltage on the error amp inputs. If this signal were not provided, there would be a slight deflection error when an analog input signal was present.
The outputs of the X and Y deflection amps can swing between +60V and -60V. This voltage is high enough to provide up to 8 amps, peak-to-peak, of current through the deflection coils.
The color drive circuits are Tocated in schematic bluck C and Uiey aveepl
a 4 volt maximum signal on the RGB inputs. The outputs drive the three electron-beams in the CRT. Three nean glaw-hulhs, NE~100, 101, and 102 act as spark arrestors for the color-drive outputs to the CRT. In block D, the CRT is shown, as well as the brightness adjustment for it. The circuit of D 409, R 411, R 410 is a spot-killer that prevents the electron-beams from burning a hole in the phosphor surface of the CRT when the monitor is turned off. Section G of the schematic consists of the high-voltage oscillator in IC 900 (14-2155-01) which operates the high-voltage transformer, T 901. This transformer is technically a flyback Lype, bul iL is nul useu bu vefleck the beam.
The IC serves two other functions; it senses the presence of the 10.3KV through R 921 and R 932 and compares it against the 9.1 supply voltage to ensure aregulated output, and also senses the varying current in either deflection coil. If no change is detected, the IC shuts down the high-voltage oscillator to prevent the beam from "burning" the face of the CRT.
Finally, the X-Y power supply is shown in block E, gencrating the following voltages: +60V to X-Y power amplifiers +55V to RGB video drivers and spot killer +9.1V to the IC's +120V. to the EHT oscillator
A degaussing circuit is provided through D 404, D 405, and R 400. The CRT is automatically degaussed when R 400 is cooled sufficiently to conduct current through the degaussing coil.
6-80
It's not hard to imagine how fast the input signals to the color X-Y monitor must be changing in order to produce the game displays. It's also obvious that a computer must be making all this happen. That is exactly the case with the G-80 hardware used in Color X-Y game. It contains two new boards, the X-Y Timing and X-¥ Control boards that produce the X-¥ monitor input signals. The G-80 stil} relies on its CPU, EPROM, Sound, and Speech boards to complete the computer.
But what does a digital computer have to do with producing the analog signals required by the X-Y monitor? Basically, the computer converts certain digital signals into analog ones. On the G-80 X-Y boards are circuits (some are actually single IC's) called Digital-to-Analog converters, D/A for short. These circuits accept a particular digital word, that is, a string of O and +5V voltage levels. The D/A converter senses the word and outputs one and only one voltage level which corresponds to the digital word. tor example, we could design a simple D/A converter that would generate the following voltages when
we Inpul certain digital words:
DIGITAL WORD ANALOG OUTPUT
0000 -1 Volt WwW +1 Volt 1000 0 Volt
This is a very basic case, bul it shows that, tor a particular D/A converter, we always produce one voltage leve] from the corresponding digital input. If we cycle through a variety of digital inputs, we'll yel a variety or Output voltages. If we do this fast enough, we actually create a rapidly varying range of output voltages. This output is exactly the kind of signal we need to drive the deflection coils in the monitor.
Now that we know where the analog signals come from, what about the digital Ones? Before we can display anything on our X-Y screen, we have to ask some questions: (Answers are provided for examples saké)
QUEST IONS ANSWERS
- What do you want on the screen? A triangle.
- How many? One.
- What design? - What angle? Equalateral (3-60° angles).
- What. size? 3" ona sive.
- Positioning? Centered an the screen.
- What colors? 2 sides white, 1 side blue.
- Screen alignment? Like this:
BLUE
- What will it do? Just sit there.
- How many lines does the electron- In our triangle, the beam have to trace? beam must make 4 lines:
B, c
D W-olue
A (even though we don't see it), B.C, and D.
Now that we have our specifications, we have to store this information someplace so the Timing and Control boards can get to it and understand. That place is video memory RAM (or Random Access Memory). It holds 4096 eight-bit words or bytes. Naturatly, we don't place all this into memory and nope tne X-Y boards can find it; it's stored in an orderly fashion.
First, we divide the video memory into two main groups - let's call them 1) The Symhal Instructions and, 2) The Line Instructions. Into the Symbol Instructions Section we store one group of ten words for every symbol or design we put on the screen. In our example, we have only one symbol, so we use only 10 words. Into the Line Instructions Section we put one group of four words for every Line that the beam has to draw. So, for our triangle, which requires 4 lines, we would store 4 groups of 4 words in the Line Instructions space. Every word we store in memory has one and only one address, so the same word can be called on over and over. Now let's Took closer at the Symbol Instruc tions memory space. Here is what the 10 words do: (Don't be concerned with the actual values of those words right now.)
WORD 7 It tells the X-Y boards either to make the beam draw the symbol in this group of words or not to draw it. And the same word informs the boards that either this group of words
is the only group or that there are more IU-word groups to follow.
WORD 2 and 3
WORD 4 and 5
WORD 6 and 7
WORD 8 and 9
WORD 10
Again, since groups after the
of memory:
WORD 1
WORD 2
WORD 3
WORD A These tell the boards where the beam is on the X-axis.
These tell the boards where the beam is on the Y-axis. The last four words then, give the exact coordinates of the electron-beam.
Words 6 and 7 tell the X ¥ hardware what the first addres3 is of the Line Instructions section,
These tell the hardware how the complete symbol (our triangle) will appear on the screen, or at what angle.
This word tells what the overall size of the design wil? be.
we're only making one design, there will be no more t0-word
one above. Now take a look at the Line Instructions section
GROUP |
This word tells the G-80 boards either to blank or to unblank
the line. And, it informs the boards that either additional 4-word groups follow or no more groups follow. Finally, it defines the color this particular line is to be.
This word represents the length of the line the beam is to
draw.
Word 3 tells the hardware at what angle the beam should make its Tine, 45°7, 90°?
Word 4 defines in which of the four sections of the screen
the line is to appear - which quadrant.
The remaining 4-word groups contain the same representations of their
respective tines, as in Group 1. The values will be different, of course,
depending on how the lines differ. In our triangle example we would find 3 more groups of four words after Group 1.
By now, you may be wondering what all these “words” really are. Since we are dealing with a digital computer, the "words" we described above must be digital, More accurately, they are digital values of the specifications required to create our designs. We have taken the specifications for sices, angles, shapes, colors and locations and converted them into digital words and create displays that the word represent.
Before we go any further, you should know that the words read from the video RAM didn't get there by magic. The microprocessor put them there. All° words that represent a1] the characters and designs in a game are kept safely Tn EPROM (Erasable Programmable Read Only Memory), on the EPROM board. When the game is powered up the CPU moves the various word groups from EPROM to RAM.
Once situated in video memory, the words are made available to the Timing and Control boards to create displays. Briefly, here is what the two X-Y boards do with the words:
After all the character words are loaded into video RAM, the Program Counter is forced to call on the first RAM address. Here the Program Counter finds the first word in the Symbol Instructions section. One at a time, these ten words are taken out of RAM and latched into specific parts of the X-Y boards. This sequence is controlled by the Timing Generator which generates 15 aclive-luw signals; only one signal pulses low at a time to latch the words. Next, the following sequence occurs:
- Word 1 is latched into U52, Last Symbol block.
- Words 2 and 3 (from the Symbol Instructions) are loaded into the X-axis Up/Down counters.
- Words 4 and 5 are loaded into the Y-axis Up/Down counters.
4, Words 6 and 7 are stored in the Vector Address counter.
- Words 8 and 9 are stored in the Symbol Angle latch.
- Word 10 is loaded into the Serial Multiplier.
Now the first 10 words of a character we wish to display are stored somewhere. If we had not wanted to draw this character, the Program Counter would have jumped to the next set of 10 symbol words, if there were another symbol. Once the Program Counter is finished moving out the words, the Vector Address counter takes control of memory. This switching between the Program and Vector Address counters is governed by the Multiplexer. Through it, the G-80 Address Bus or onc of the other counters van auuress video memory. Only one aevice 1s allowed access to memory at atime. When it is the Vector Address counter's turn to get into memory, the counter addresses the first word of the Line Instructions section. The reason for this, is that the Vector counter was previously loaded with words 6 and 7 in the Symbol Instructions section. These words teil the Vector Address counter the locations of the first word in the Line Instructions section. Now the Vector counter causes the Line Instruction
words to be moved out of memory, one at atime. Here is what happens to the group of four words:
- Word 1 is stored in the Color Latch and in U52, Last Vector.
- Word 2 is stored in the Vector Length counters.
- Word 3 is loaded into the Vector Angle circuit.
- Word 4 1s used in the Vector Angle circuit.
Up to this point then, 10 words Lhal Uestrive some symool and 4 words tnat
represent one line in that symbol have been clocked out of memory. When the Vector Address counter takes out the last group of words that represents thc last line to be drawn, memory access is switched back to the Program Counter. It will now either restart the sequence as before (if there is another symbol to be drawn) or it will stop until the counter is reset to the beginning again.
Now the system is ready to draw its first line, to actually move the beam, because we have given it exact specifications to do so. The position of the electron-beam is nuw knuwi, (Kurds 2 through 5 1n the Symbol Instructions} so
we know where the beam will start to draw. Then, the X-Y boards calculate tne Tength and angle of our first line. Ana they know the color, if any,-of this line. (In our triangle, recall that our first line, A, is one that we Shouldn't see, although it must be drawn. We also know that it must be drawn at a 0° angle, straight up.) The boards calculate the line length and angle by assigning a certain number of digital clock pulses to these qualities. The circuitry acts as a digital “ruler" and "protractor" and measures any line, in terms of how many pulses in length and angle it is. All this figuring is performed by the Full Adder's, 2708 EPROM and Rate Multiplicrs. The output of each Rate Multiplier (XCL and YCL) is a string of clock pulses that clock the respective Up/Down counter, X or Y. But the pulses are not just random pulses, they are the digital equivalents of a line with a particular length and angle. So we clock both Up/Down counters at the same time with these pulses. Doing so we force the counters to start counting from the beam position words previously stored in the counters. The important point is this; if we change the digital values of the beam position words, we change the position of the beam through the D/A converters. How far, and at what angle we change the beam depends on the amount of pulses applied to the Up/Down counters. Just before the beam is moved, the color of the line (black included) is sent to the monitor through the RGB D/A converters.
There you have it - one line. For more lines, the G-80 system rapidly follows the same procedure of reading the symbol? and line words, latching them, calculating line values, color values, and then forcing the beam line-bytine to form complete symbols.
Notice that throughout our discussion, we have mentioned the microprocessor's role just once; loading the character word into memory. During an actual game however, it does more than act as a "loader". Whenever we want to move our symbols on the screen, for example rotate the triangle, we need some way of changing all those words to represent new lines and angles. The CPU fulfilis this job nicely. Under program control, the CPU is told when ana how to alter these words to create a whole range of dynamic displays - different colored lines, new angles, longer or shorter lines, bigger or smaller characters, whatever the game play calls for. Also, the microprocessor governs functions such as player control and coin inputs, or sound and speecl outpuls.
The CPU then, gives us the variety and color in our X-Y games. - PLEASE NOTE: The designations in parenthesis will be used throughout the following detailed discussion to refer the reader to the proper schematics. C = X-¥ Control Board (P/N BUU-UIb3) sneets > and 6. | = A-¥ 11ming Boara (P/N 600-0161) sitet 5, 6, and 7. e.g. (C6) = Control] Board, sheet 6.
The CPU addresses video memory, U24-U31, through multiplexer IC's U48 and v49 (C5). Character words are taken from memory as the Program Counter, ICs U33, U34, U22 (C5), addresses them through multiplexers U36, U49, U35, and U2? (C5). If Word 1 (Symbol Instructions) says to not display a symbol, the Program Counter is advanced 10 counts by U33, a full adder, which adds 10 to the counter when signa? ADD goes law, The Vector Address counter is composed Of UIO, UTI, amd UTZ (C5) and iy luaded wilh the first address of the Line Instructions from video memory's Character Data Bus, CDO-CD7. The CPUs Data Bus, DO-D7, is brought to the memory through a bi-directional buffer, UI4 (c5). The signal labelled FETCH (C5) latches the various Character Data words from memory. The MUX (C5) signal commands the multiplexer ICs to allow either the CPU, Program Counter or Vector Address counter to address memory. MEMR (memory read) and MEMW (memory write) come from the CPU board to read from or write to the RAM. Signal VCE (C5), Vector Clock tnable, increments the Vector Adaress Counter. PCC (Program Counter Clock) is the string of pulses that advances the Program Counter; PCR (Program Counter Reset) ensures that the Pragram Counter starts counting at the first location in video RAM each time PCR goes low. This signal occurs first at power-up and then 40 times a second during program execution. So, it causes the X-¥ monitor to draw and re-draw each symbol on the screen 40 times a second. The signal is generated from the master clock (crystal ¥1 and U14, 17) by U31-U34 and U2Z (1/). The otner clock signals (VCE, PCC, FETCH, ADD, MUX, and VCL) are all generated by the X-Y
liming boara (17).
The outputs of the }ast Symhol and last Vector latches (U52. T7) are AND gated together with the signal END, which originates from the Contro} board's U18 (C6). When U18's output goes low, it signifies that no more symbols are to be drawn, Then the Program Counter is reset by the 40 Hz signal to the start of the video memory to repeat the display sequence. U22 (17) is the DRAW latch and its output, through U2I, creates the DKAW Signal which initiates 4
sequence that causes the beam to draw. This sequence occurs on the Timing Board, sheet 6; by this time, all video words have been stored in their proper Places in the system, On the Timing Board (T7), the vector angle is in U56, the symbol angle in U55. So when DRAW goes high, it causes strings of digital pulses that represent the vector and symbol angles to be generated. These streams of pulses (from U28, T6) are the ones that clock the X and Y Up/Down counters, shown on {5 (U15-UZQ). Ud5 (16) tells the counters in which direction to count, up or down (D/U X, D/U Y). Then, the outputs of the Up/Down counters, X and Y, become the digital words that arc converted to analog signals by D/A converters U1 and U4 (T5). On Amps U2 and U3 (T5) convert current from the D/A converters to voltage levels. These levels drive the Vertical and Horizontal inputs to the monitor. Signals DRAW and VCL are combined in U28 (T6) to form DCL (Draw Clock). This signal clocks down the Vector Length counters U15, U16 and U17 (C6) which contain words that represent various lengths of the lines to be displayed. When the counters have counted down to U, the END Signal becomes active. AS the X and Y Up/Uown counters are clocked, their outputs are sensed by U5-U10 (T5), which are multiptexers. The multiplexers are necessary to tel] the system when the beam is off the screen. It does this by generating the BOS signal (15). Then BOS is AND gated with DRAW at U5 (C6), to blank (turn off) the beam whenever BOS goes Tow.
U3 (C6) compensates for the inherent delay in deflecting the electronbeams. It provides a number of taps to select a range of delay times. From U2 (C6), the color word is read and applied to the RGB D/A converters US, U1 and associated diodes and resistors. The RGB outputs go directly to the color X-Y monitor.
U50, a 74LS154 (17) decoder IC, selects one of 15 outputs by making the output low. The outputs sequentially store the video memory words, one at a time. U50 is enabled at pin 18, forty times per second by U22 (17), and at pin 19 by U21. U51 sequences USO through its 15 count cycle; at count 14, pin 16 of USO goes low to initiate the DRAW signal through U40, U21 and U22 (T7).
The circuitry at the top of schematic, C6 (U45, U51-US4), is not used in generating and displaying characters on the X-Y monitor. Its function is to perform lenglhy caiculalions umer suftware control.
ADJUSTMENTS AND SPECIFICATIONS
On the X-Y |iing Board, there are two potentiometers that. adjust the outputs of the X and Y current-to-voltage converters (U2 and U3, respectively),
they are:
R3 (X)} ue R6 (Y) U3
On the monitor, there are a number of factory-set adjustments. 00 NOT USE
THESE CONTROLS. They are:
R106 R917
R117 R918 R611 R920
R702
The following controls can be used to adjust the monitor if necessary:
R605 Vertical
R712 Horizontal
R107 Red
R118 Green R36 Blue
R930 Brightness R922 Focus
Input specifications from the G-80 boards to the color X-¥ monitor arc:
Vertical Input 33V maximum Horizontal Input +4V maximum Red Input +4V @ full brightness Green Input +4V @ full brightness Blud Input +4V @ full brightness
VOLTAGE ANALYSIS FOR THE GO8-Q03 COLOR X-¥ MONITOR
DEFLECTION PCR
P 900 (EHT) Pin 1 2.8 VAC
2 3.5 VAC
3 -9.1 VOC
4 9.1 VOC
5 GRD 6 &RD
7 5.0 VAC
8 120 voc
9 OPEN 10 400 VDC
0 401 - cathode 63 VOC
D 403 - cathode 63 VOC
2 400 - anode -63 VDC
Db 402 - anode -63 VDC
ZD 400 59 VDC
zD 401 9.0 VDC
ZD 402 -9.1 VOC 0 400 - base 59 VDC, - emitter 58.8 VDC, - collector 63.5 VDC Q 401 - base 9.7 VDC, - emitter 9.1 VDC, - cotlector 17 vOC
| Pin 1 | 0 | 10 | ie) |
| 2 | 4.2 voc | VW | 0 |
| 3 | u | 12 | -9.1 VDC |
| 4 | 0 | 13 | 0 |
| 5 | 0 | 4 | 0 |
| 6 | 9.1 VOC | 15 | Q |
| 7 | 7.5 VOC | 16 | 0 |
| 8 | 0 | 7 | 0 |
| 9 | 0 | 18 | 4.2 VDC |
| Q 600 - collector | 34.5 VDC | Q 700 - coltector | 35.9 VDC |
| Q 601 - collector | 0.8 VOC | Q 701 - collector | 0.5 VDC |
Q 602
Q 603 -
Q 604 -
Q 605 -
Q 606 -
EHT PCB
Te 900
Pin CON RA eR Wr I
Q 901 -
Q 902 -
Q 903 collector
collector
co}lector
collector
base
emitter
collector base
emitter
emitter
base
collector
emitter
base
collector
emitter
base
collector -O.5 voc
63.5 VDC
~63.9 vor
63.9 VOC
0.1 VOC
0.1 VDC
-63.9 VDC -0.1 VOC
-0.1 Voc
0.4 voc
0.1 VOC
-9.1 VOC
9.0 VDC
0.7 VOC
1.7 VDC
7.5 VOC
0.1 voc
8.0 VOC
7.5. VOC
0.3 voc
ie} Q.3 voc
0.5 VDC
0.5 voc
3.0 VDC Q 702
Q 703
Q.704
0 705
Q 706 > collector
- collector
- collector
- collector
- base
- emitter
- collector ~ base
- emitter ~0.8 VOC
63.5 VDC
63.5 voc
63.9 VOC
0.1 VOC 0.1 VOC
-63.9 VDC -0.1 VOC
-0.1 VBC
1.7 VOC
8.7 VOC
8.7 VOC
2.3 VOC
9.0 VDC
0.5 voc
0.1 VDC
8.7 VOC
oO
Iustrations
Rawer-scan Display
Figure 1 Figure 2
X-¥ monitor ~. Nice Lines
Figure 3 Figure 4
TOP ASSEMBLY
TOP ASSEMBLY
QTY REQD
]
*
x DRAWING NUMBER 700-0090
ORAWING NUMBER 700-0091 DRAWING NUMBER 700-0092
OCSCRIPT ION
Speaker Cover 6 X 9 Speaker 6 X 9 8 Ohm 10W Cover Junction Box Cabinet Universal Game
Coin Mech W/Light Coin Mech W/L ight *Quantity 2 Coin Mech the same either 220-0194 or 220-0195. TOP ASSEMBLY
ITEM NO. PART NO.
1 130-0002
2 130-0020
3 140-0021 4 140-0055
5 220-0194
220-0195
6 250-0038
7 250-0048
8 250-0492 9 250-0497
10 253-0222 11 253-0228
12 253-0265
mB 260-0001
14 280-0005
15 280-03 24 16 280-0359
V7 220-0178 18 281-0014-28
19 281-004 2-32 20 281-0042-08
a1 281~0045-12 2? 221-062-028
24 253-0235
25 282-0005-20
a 282-0017-16
28 282-0017-24 Moulding Strip Clip Switch
Moulding Logo Clamp Component Board Universal
Coin Receptacle Panel Monitor Clear Universal
Panel Logo Tan Axial Cooling IR Cable Tie
Cable Clamp Nylon Electrical Crimp Steeve
Draw Catch
Screw 8-32 X 1-3/4 In Oval HD Mach Screw 6-18 X 2 In Pan HD Type A/AB Screw 6-18 X 1/2 In Pan tt Type A/AB Screw 10-12 X 3/4 In Pan HD Type A/AB Screw 6-18 X 1/2 In Flat HD Type A/AB
Plastic Pouch 2 t/2 X 3 Vinyl Bott Carriage 10-24 X 1-1/4 In Mach
Bolt Hex 1/4-2U X J in Mach Bolt Hex 1/4-20 X 4-1/2 In Mach
TOP ASSEMBLY - Cont inued DRAWING NUMBER 700-0090 TOP ASSEMBLY - Continued DRAWING NUMBER 700-0041 TOP ASSEMBLY - Continued DRAWING NUMBER 700-0092"
ITEM NO. PART NO. QTY REQD DESCRIPT1ON
| 30 | 283-0015 | ] | Nut Wing Mach 10-24 |
| 3 | 283-0024 | 4 | Nut Hex Mach 8-32 |
| 32 | 283-0025 | 14 | Nut Hex Mach 10-24 |
| 33 | 420-0753 | 1 | Decal Dip Switch Settings ZEKTOR |
| 34 | 284-0012-06 | 4 | Washer Flat #6 - .150 ID X .375 OD. |
| 35 | 284-0014-07 | 4 | Washer Flat #8 - .190 ID X .437 OD. |
| 36 | 284-U016-U8 | 14 | Washer Flat #10 - .220 [ID X .500 OD. |
| 37 | 320-0020 | 2 ft | Sealant Foam |
| 338 | 284-0027-20 | 6 | Washer Flat 1/4 - 1,250 Large OD Fender |
| 39 | 284 ~0032 | 2 | Washer Lock Split #6 |
| 40 | 284-0034 | 4 | Washer Lock Split #8 |
| 41 | 284-0036 | 24 | Washer Lock Split #10 |
| 42 | 284-0037 | 6 | Washer Lock Split 1/4 |
| 43 | 286-004 4-12 | 4 | Screw 8-15 X 3/4 In Pan HD S/M Black |
| 49 | syu-vuly | 1 | Lamp Fluorescent |
| A7 | 420-0030 | 1 | Decal Caution 115V |
49 420-0568 50 420-0624 Decal FCC Light Baffle
| 51 | 420-0636 | ) | Tag Extra Value |
| 52 | 420-0656 | 1 | Decal Self Test Instructions |
| 53 | 420-0743 | 1 | Manual |
| 54 | 420~-0/68 | ! | Graphic Intertor |
| 55 | 420-0746 | 1 | Decal Game Instructions |
| 56 | 420-0748 | 7 | Box Decal |
| 58 | 800-0145-01 | 1 | Junction Box W/5 Amp Fuse |
TOP ASSEMBLY - Continued TOP ASSEMBLY - Cont inued TOP ASSEMBLY - Continued
ITEM NO. PART NO. QTY. REQD
59 800-0147-01 1 60 800-0192
61 800-0232 62 800-0255 63 800-0380 64 800-0280
65 800-0284 66 800-0290 67 800-0315 68 800-0321
69 800-0322 70 800-0375 ral 800-3246 72 800-3251
23 420-0713 DRAWING NUMBER 700-0090
DRAWING NUMBER 700-0091 DRAWING NUMBER 700-0092
DESCRIPTION
Fluorescent Lamp Assy 2 UL Assy Harness Speaker 680 Assy Harness Gnd Assy Harness Mon AC In Assy Connector Bracket Assy Coin Counter Assy Harness Gnd Coin Mech Assy Gnd Strap Control Panel Assy Harness Coin Mech Lighting Assy Harness Coin Mech Assy Cord Fan Monitor Assy Control Panel Complete Assy Camponent Shelf Assy Advertising Pouch
Top Assembly 700-0090 Top Assembly 700-0091 Top Assembly . 700-0092
0; Oma @ > as
|” AG) oA) 2:
foul SECTION A-A
Top Assembly 700-0090 Top Assembly 700-0091 Top Assembly 700-0092
Hi ADHESIVE SOCOF TeMmT
=) DETAIL ‘C”
U {) ‘gg ~ 8 SECTION 6-6
Top Assembly Top Assembly Top Assembly
700-0090 700-0091 700-0092
CONTROL PANEL ASSEMBLY
ITEM_NO.
> Sw©C MNO wne PART NO.
250-0538
253-0266
800-0383
240-0111
240-0006 240-0009
510-0064
280-0329
282-0005-12
284-0016-08
284-003 6
283-0005
800-0374
280-0251
283 -0002-10
284-0012-06
800-3 248
280-0327
280-0005 240-0126
600-0092-42
600-0092-47
600-0092-50 QTY _REQD.
Pea NNN So
+
nn: Ce
1.00'
2.08° DRAWING NUMBER 800-3246
DESCRIPTION
Subpanel Metal Graphic Control Panel
Rotary Knob Assy Button, Plunger, Blue Button, Plunger, Red Button, Plunger, Yellow
Switch Push button Metal Panel
W/2 IN ~ 13 Hex Pal Nut
Bolt 10-24 x .750 Carriage Mach Washer, Flat #10-.220 1.0. x .500
0.0.
Washer Lock Split #10 Nut 10-24 Hex Self Locking Interface Assy Single Player Control Panet
Standoff, PCB Support 1/4 IN Screw 6-32 x 5/8 IN Pan HD Mach Washer, Flat #6-.150 1.0. x .375 0.0.
Control Panel Harness Assy
Base Tie Wrap
Cable Tie Knob
Wire 22 AWG Red Electrical Hookup
Stranded Wire 22 AWG Violet Electrical Hookup Stranded
Wire 22 AWG Black Electrical Hookup Stranded
Control Panel Assembly
800-3246
Control Panei Assembly 800-3246
yoo fie]
5.15 [ee}
it PI AYFR’ C= NO. > Pi AYER) NOT Oo a 12.00 [305] \\ es @)sw ra . 76] {@emten (22) 15.00 (381) auu
- 4.00 [102]
SINGLE PLAYCR CONTROL PANCL INTERE ACC ASSEMBLY
ITEM_NO.
ON DAA RW KH
os os n= Ow PART _NO.
150-0088
151-0058 151-0059 170-0 258 212-0024
212-0156
314-0055 314-0062
314-0075 314-0085
471-0102 477-0043 ary REQD.
Ba worn onwe ee wen DESCRIPTION
Cap E 10 uf 25V RDL
Cap .01 uf 16V AX Cap .001 16V AX
PC Board
Conn 12 Pin M RTA PLRZD
Conn Header 15 Pin
IC 74LS2a4
IC 74t$74 IC 7448393 IC 74.$14
Res 1K Ohm 1/2W 5% Res Pack 9 x 2.2
SIP 10-POS DRAWING NUMBER 800-0374
REE DES.
cl, ¢2 ca
P30
P10
U2, U3 u5
u4
R1-R3 RPI
Single Player Control Panel Interface Assembly 800-0374
ROTARY KNOB CONTROL ASSEMBLY
ITEM NO.
COON AaB wr PART NO.
250-0543
250-0544
280-0430
289-0001-10 250-0545 281 -0031-04
800-0382 40 2-000 2-06
284-001 1-05 QTY REQD
Ce Cee ee DRAWING NUMBER 800-0383
DESCRIPTION
Brkt, Rotary Knob Control Shaft, Rotary Knob Controt E-Ring Pin .099 Dia X .625 tg, Roll, Spring Stl Flywheel Rotary Knob Control Scr #4-40 X 1/4" PN HD Thd Forming
Rotary Interface Assy Bearing 1/4 I.D. X 3/8 Sintered Bronze Wshr #4 Fl, SM OD, Sti
Rotary Knob Control Assembly 800-0383
ROTARY ASSEMBLY INTERFACE
ITEM NO..
uM Bw Hw PART NO.
170-0160
212-0081
285-0001-04 370-0006
470-0101 QTY REQD
—- nro nw DRAWING NUMBER 800-0382
DESCRIPT LUN
PC Roard
Conn M 4 Pin RTA PLRZD
Rivet .125 Dia X .25 Lg Opto Electric Encoder XSTR Res 100 Ohm 1/4W 5% REF DES ©
Pl
DSI, DS2 RI
Rotary Interface Assembly 800-0382
TOP
NUMBER MARK
HZIAZ NOTCH FACING BOTTOM senB 185
FLOURESCENT LAMP 2 ASSEMBLY DRAWING NUMBER 800-0147-00 FLUORESCENT LAMP 2 ASSEMBLY DRAWING NUMBER 800-0147-01
QTY REQD. ITEM_NQ. PART NO. -00 -01 DESCRIPTION
| 1 | 211-0041 | 2 | 2 | Conn Pin Amp |
| 2 | 211-0044 | 1 | 1 | Conn Cap Amp 2 Pin |
| 4 | 211-0166-00 | 1 | - | Conn Crimp Ring #10 |
| 6 | 280-036) | - | 1 | BSHG STR RLF AC Cord |
| 7 | 280-0362 | - | 2 | Elec CRP SL 24-18 ANG |
| 9 | 281-0002-06 | 1 | 1 | SCR #6-32 x 3/8" PN HD Mach |
VW
| 14 | 284-0002-00 | - | 1 | Washer Flat STD 0.D. #6 |
| V7 | 390-0083 | 1 | - | Fluor Lamp Fxt 18 IN |
| 18 | 390-0117 | - | 1 | Fluor Lamp Fxt 18 IN U.L. |
| 23 | 600-0079-00 | 1 5.9° | CA 2 Cond Zip Cord |
Fluorescent Lamp 2 Assembly 800-0147-00 Fluorescent Lame 2 Assembly 800-0147-01
=o accy
SZ Ol ASSY
Aa
VOLUME CONTROL BLOCK ASSEMBLY
ITEM NO.
cConoannwn PART _NO~
211-0005 211-0041
285-0001-04 211-0046
470-0331
212-0005
240-0001
250-0462
280-0005
420-0623 475-0007
§10-0051 600-0013 QTY REQD.
Neo wow nnw ocean
3.1 feet
0.1 feet URAWLNG NUMBER 80U-02/7
DESCRIPTION
Connector Crimp Lock Connector Pin Amp Pop Rivet, 1/8" x 1/4 Lg Connector Cap Amp, 6 Pin Resistor, 330 ohm 1/4 watt 5% connector, remale, black 4 Pin Volume Control Knob ;
Volume Control Bracket
Cable Tie
Operator Panel Decal Pot, 10K, CAR Panel Mount Pushbutton Slide Switch
1 Condition Shielded Cable
Heat Shrink Tubing, 1/8" Diameter
Volume Control! Block 800-0277
awaion | \awmion | aouas| sasae 8 | © 70 | O|®@ = AS . C25 Ei Ce)
COIN COUNTER ASSEMBLY
ITEM_NO. PART_NO.
1 220-0008 250-0496
3 281-0002-08
284 -0002-00
284-0032-00
6 283 -0022-00 gTy_REQD. DRAWING NUMBER S00. 0280
DESCRIPTION
Digital Counter, 6 volts Coin Counter Bracket
Pan Head Phillips screw, 6-32 x 1/2" machine
Flat Washer, #6
Split LOCk Washer, #6 Hex Nut, #6-32
800-0280
Coin Counter Assembly
A.C. JUNCTION BOX ASSEMBLY DRAWING NUMBER 800-0145-UU A.C. QUNCTION BOX ASSEMBLY DRAWING NUMBER 800-0145-01 A.C. JUNCTION 80X ASSEMBLY DRAWING NUMBER 800-0145-02
QTY REQD.
| ITEM.NO. | PART NO. | _-00 _-01 _-02 | DESCRIPTION | ||
| 1 | 140-0020 | 1 | 1 | 1 | Junction Box Metal |
| 2 | 211-0165 | 2 | 2 | 2 | Conn Quick Fem Fully Insl. .250 x |
-U3Z (AWG 18-22)
| 3 | 211-0164 | 4 | 4 | 4 | Conn Quick Fem Fully Insl. .187 x |
-020 (AWG 18-22)
| 5 | 280-0361 | q | 1 | 1 | Bushing S/Rel AC Cord |
| 6 | 270-0001 | Ts od | 1 | filter EMI | |
| 7 | 280-0007 | tT. 1 | 1 | Bushing S/Rel 1/2 | |
| 8 | 280-0362 | 4° 4 | 4 | Electric Crimp Sleeve AWG 24-18 | |
| 9 | ~ 420-0598 | 1 | - | - | Decal 2 Amp Fuse |
| 10° | 510-0013 | 4 | 1 | 1 | Switch SPOT Cherry |
| 11 | 514-0001 | Too oe | - | Fuse 2 Amp 250V S.B. | |
| 12 | 514-0005 | “yr. | 1 | Holder ruse | |
| 13 | 600-0001 | | | 1 | 1 | Cord Line 3 Cond. |
| 15 | 600-0079 | 2 Ft. 2 Ft. 2 Ft. Cord Line Zip | |||
| 16 | 280-0005 | “2 | 2 | 2 | Cable Tie |
| 7 | 218-0002- 10 | 2 | 2 | 2 | SCR PN HD Phil #6-32 x .625 Mach |
| 18°.” | 283-0022-00 | 2 | 2 | 2 | Nut Hex HD #6-32 Mach |
| 1 | 284-UU4z-UU | 2 | 2 | 2 | Washer Lock Int. Tooth #6 |
| 20 | 281-0004-12 | 1 | 1 | 1 | SCR PN HD Phil #8-32 x .750 Mach |
| 21 | 283-0024-00 | 2 | 2 | 2 | Nut Hex HD’ #8-3 2 Mach |
| 22 | 284-0044-00 | 1 | 1 | 1 | Washer Lock Int. Tooth #8 |
23 ry
24 284-0007-00
25 283 -0025-00 26 282-0005-28
27 310-0016-16 Washer Flat STD 0.0. #1/4 Nut Hex HD #130-24 Mach Bolt Carriage #10-24 x 1.750 Mach Insul TGB .187 10
A.C. JUNCTION BOX ASSEMBLY-Continued A.C. JUNCTION BOX ASSEMBLY-Continuad A.C. JUNCTION BOX ASSEMBLY-Cont inued
QTY. REQD.
| ITEM_NQ. | PART NC. | 700 _-01 | |
| 28 | 284-0004-00 | 2 | 2 |
| 29 | 420-0597 | - | = |
| 30 | 420-063 4 | - | 1 |
| 31 | 514-0051 | ~ | - |
| 32 | 514-0053 | - | 1 |
DRAWING “NUMBER 800-0145-00 DRAWING NUMAFR ROO-1145-01 ORAWING NUMBER 800-0145-02
DESCRIPTION
Washer Flat S7D 0.0. #8 Decal 1 Amp Fuse Decal 5 Amp Fuse Fuse 1 Amp 250V Fuse 5 Amp S.B.
A.C. Junction Box Assembly A.C. Junction Box Assembly A.C. Junction Box Assembly
& 3.00
SMOOTH ou
WIRE ~ 800-0145-00 800-0145-01 800-0145-02
17¥ eX 19) 2PL
24.00
COLOR MONITOR ASSEMBLY
ITEM _NO.
NAN Bw KH A PART NO.
200-0025
211-0059
252-0175
282-0017-24 284-0027-20
283 -0007-00 QTY REQD.
ros = DRAWING NUMBER 800-0375
DESCRIPTION
Culor onitor 19" x-¥
Conn Plug 3 Pin Amp
Monitor Mounting Board Hex Head Bolt 1/4-20 x 1.500 Lg Washer Flat 1/4-1.250 Lg OD Fender Nut-Hex, Self-Locking, Mach 10-24
Color Monitor Assembly 800-0375
COLOR MONI TOR ASSEMBLY
ITEM _NO.
MAD B® wWH PART NO.
200-0025
211-0059
252-0175
282-0017-24 284-0027-20
283 -0007-00 Qry REQD.
Pop a DRAWING NUMBER 800-0375
DESCRIPTION
; Color anilor 19" X-¥
Conn Plug 3 Pin Amp
Monitor Mounting Board Hex Head Bolt 1/4-20 x 1.500 La Washer Flat 1/4-1.250 Lg OD Fender Nut-Hex, Self-Locking, Mach 10-24
19" X-¥ COLOR MONITOR-Cont inued
PART_NO. DESCRIPTION
EHT SUPPLY ASSEMBLY CONT'D
RESISTORS 475-0043
475-0044
470-0271
470-0471 471-0220
470-0330
470-0680 462-0001
464-0114
470-0333 470-0274
473-0475 471-0331
472-0470 470-0562
EHT SUPPLY ASSFMRLY KIT 482-0242
475-0035 EHT REGULATOR ASSEMBLY
SEMI-CONDUCTORS
482-0268
482-0269 401-0204
CAPACI TORS
152.0149
151-0108
RESISTORS
472-0223
471-0683 472-0273 200 Ohms Controt
2K Control 270 Ohm 1/4W 5% 470 Ohm 1/4W 5% 24 Ohm 1/2W 5%
33 Ohm 1/4W 5% 68 Ohm 1/4W 5%
68 Ohm IW 5%
470K Control
33K T/4w 5% 270K 1/4W 5% 4.7M 1/2W 5% 330 Ohm 1/2 10%
47 Ohm IW 5%
5.6K 1/4W 5%
PWR Transistor 5A 1400V
Focus Control
2N 6558
TIP 47 (Motorola) IN 5263
68 pf 500V 470 pf 500V
2x IW 5%
68K 1/2W 5% 27K WW 5% DRAWING NUMBER 200-0025
RES. OES.
ROT
R918
R923
R924
R95
R927
R930
R932
R933
R935
R936 R937
R940
R941
R942
R922
0320, 321, 323 9322 203 40
c330
C331
R300
R301
R302
aa) SYR OMEY: PSNR MONE TOR-Tantinued DRAWING HURBER 200.00
PART NO. DESORIPT LON RES. DES.
EHT REGULATOR ASSEMBLY CONT'D RESISTORS
| 471-0473 | 41K 1/2 5% | R304 |
| 470-0331 | 330 Ohm 1/4W 5% | R305 |
| 47) -03R3 | 3.3 Ohm 1/2 5% | R306 |
| 470-0363 | 36K 1/aw 5% | R307 |
| 460-0008 | 4 1/4 5% | R308 |
| 475-0048 | 10K Control Pot. | R310 |
DEFLECTION AMP PCB ASSEMBLY SEMI-CONDUCTOR S
| 315-0117 | Input Amplifier IC | 1C600 |
| 481-0202 | Rectifier | 0400-403 |
| 481-0020 | Rectifier 1A 200V | 0404-407, 409, |
D408, 601-605 701-705 481-0006 Diode IN 914
| 481-0204 | Zener Diode IN 5263B 1/2¥ 56V | 20400 |
| 481-0205 | Zener Diode IN 52398 1/2W 9.1V | zp401 |
| 481-0179 | Zener Diode 9.1¥ IW 5% | 20402 |
| 482-0248 | Transistor TIB 298 | 400, 401 |
| 482-0244 | Transistor MPSU60 (Motoro ta) | Q600, 700 |
| 482-0245 | Transistor 300V¥ 1/2A | Q601, 604, 701, |
| 422.0702 | Transistor MPSUI0 (Motorola) | 9602, 603, 702 |
CAPACTORS
| 150-0211 | 100 uf 80V | c401 |
| 150-0212 | 680 uf 160V | c402 |
| 150-0213 | 6800 uf 80V | C403, 404 |
| 150-0004 | 10 uf 25V | c405 |
| 151-0046 | Ceramic 0.1 uf | c4o7, 621, 721 |
| 152-0056 | 0.1 uf 200V | C410 |
19" X-¥ COLOR MONI TOR-Cont inued
PART_NO, DESCRIPTION
DEFIFCTTION AMP PCB ASSEMBLY CONT'D
CAPACI TORS
150-0220
152-0145 152-0146 152-0147 152-0023
151-0107
152-0149
152-0150
RESISTORS
478-0006 473-0330
472-0223
470-0222
474-0220
471-0822
474-0680
470.0472
470-0275
470-0155 470-0621
471-0911 470-0103
470-0182
470-0303
475-0037
470-0104
470-0242
470-0102
475-003 8 22 uf 250v
2.2 pf 500V 12 pf 500V 100 pf 10% 500V 47 pf 10% 500V
0.068 uf zOuv
5.6 pf 10% 560 pf 500V 20%
Thermistor 120¥ 60 Ohm 33 Ohm 4W 10%
2K IW 10%
2.2K 1/4W 5%
220 Ohm 10W
8.2 1/2 ok 680 Ohm 6W A.7K W/AW 6%
2.7M 1/4W 5% 1.5M 1/4W 5% 620 Ohm 1/4W 5% 910 Ohm 1/4W 5% 10K 1/4W 5%.
1.8K 1/4W 5%
30K 1/4W 5%
50K Trim Pot
100K 1/4W 5%
2.4K 1/4W 5% 1K 1/4W 5%
IK Trim Pot DRAWING NUMBER 200-0025
RES. DES.
c4it
c600
C603, 703 C620, 720 C622, 722 C624, 724 C702
C725
R400 R401
R402 R403
R404 R405
R406 R410
R411
R412
R600 R601 R602 R603, 624, 724 R604
R605
R6OG
R607, 710 RANR, AIA, AX7, 715, 736, 737 R611
19" X= COLOR MONI TOR-Cont Inuea
PART NO. DESCRIPTION
DEFLECTION AMP PCB ASSEMBLY CONT'D RESISTORS 470-0183 18K 1/4W 5% 470-0622 6.2K 1/4W 5% 470-0181 180 Ohm 1/4W 5%
470-0223 22K 1/4W 5%
470-0101 100 Ohm 1/4W 5%
471-0183 18K 1/2W 10% 470-0271 270 Ohm 1/4W 5% 471-0223 22K 1/2W 5% 472-0471 470 Ohm 2W 5%
470-0151 150 Ohm 1/4W 5% 460-0056 82 Ohm 1/4W 4%
474-0160 1.5 Ohm 10W 470-0222 2.2K 1/4W 5% 475-003 9 5K Trim Pot 470-0153 15K 1/4W 5% 470-0152 1.5K 1/4W 5% 472-0391 390 Ohm 2W 5% 470-0475 4.7M Trim Pot URI SOCKET PCB ASSEMBLY
SEMI-CONDUCTORS 482-0243 Transistor MPS u10 (Motorota) LAMPS 390-0107 Lamp CAPACITORS 151-0067 100 pf 500V 151-0112 0.1 uf 200V 151-0050 0.01 uf 500V 10% ORAWING NUMBER 200-0025
RES. DES.
R620, 720 R621, 721 R622, 625, 631, 722, 725, 731 R623, 704, 705,
R626, 629. 726,
R627, 727 R628, 728 R630, 730 R632 R633
R634
REIS
R700, 701 R702
R703, 706 R714
R732 R930, 931
Q100-105
NE1NO-103
C100, 110, 130 c101
ci02, 11%, 131
19" X-Y COLOR MONI TOR-Cont inued
PART NO.
CAPACT TORS 151-0096
RESISTORS 470-0101
470-0275 462-0056
472-0471
470-0122
475-0041 476-0042
471-0222
470-0181 470-0102
47-0224
471-0102
474-0474
470-0621
HEAT SINK ASSEMBLY
482-0260
260-0010 MISCELLANEOUS
200-0040 180-0009
180-0017
213-0019 280-0208
800-0307
800-0318 DESCRIPTION
0.01 uf 1000V
100 Ohm 1/40 5%
2.7K 1/4W 5% 3.3K IW 5% 470 Ohm 1/4W 5%
1.2K 1/40 5%
250 Ohm Trim Pot
2.5K Trim Pot
22K Wen 5% 180 Ohm 1/4W 5% 1K 1/4W 5% 220K 1/2W 5% 1K 1/2W 5%
470K 1/20 5% 620 Ohm 1/4W 5%
2N 6259
Motor Blower Fan
CRT Deflection Yoke
Degaussing Coil CRT PCB Socket
Yoke Wedge Input Limiter PCR
Input Clamp PCB DRAWING NUMBER ZuU-UU25
RES. DES.
cli2, ti3
R101, 112, 130 R102, 113, 131
RIU3, 114, i3z R104, 115 R105, 116, 134 R106, 117 R107, 118, 136 R108, 119, 137
Ri09, 121 R110
R122
R123
R124
R133
Q605, 606. 705,
mol
vol
byul
L100
J101
x
x
x
X-Y P.C.B. COMPONENT LAYOUT 19” X-Y Color Monitor 200-0025
19” X-Y Color Monitor 200-0025
dhe, et
EHT P.C.B. COMPONENT LAYOUT
TRANSFORMER EML ASSEMBLY DRAWING NUMBER 800-0190
ITEM NO. PART NO. QTY _REQD. DESCRIPTION
560-0055, G-80 Power Supply Transformer ] ]
| 2 | 212-0016 | % | Connector, Female, 10 Pin |
| 3 | 211-0005 | 9 | Connector Crimp |
| 4 | 211-0045 | 1 | Connector Plug Amp, 6 Pin |
| 5 | 211-0042 | 6 | Connector Socket |
| 6 | 211-0043 | 2 | Connector Plug Amp, 2 Pin |
| 7 | 600-0079 | 1 foot | Zip Cord |
| 8 | 280-0005 | 4 | Cable Tie |
| 9 | 0.5 feet | Electric Strand Wire, Black, AWG 18 | |
| 10 | 280-0359 | 3 | Flectric Crimp Sleeve |
| YW | 211-0077 | 4 | Connector Terminal Socket, 20-14 AWG |
Transformer EMI Assembly 800-0190
it 8. [—& DETAIL A L ee 10.00 A a
COMPONENT SHELF ASSEMBLY
ITEM NO.
COON AO PY HD =
am on 2e
B PART NO. QTY REQD.
250-0458 1
252-042 1 280-03 24 1 281~0045-12 15
284-0016-08 15 284-0036-00 15
280-0005
800-0190
800-0191
800-0277
800-0285
800-0286 800-03 14
800-3 245 ee rns) DRAWING NUMBER 800-3 251
DESCRIPTION
Saddle G-80 Cage Compnent Shelf UP. Cab. Cable Clamp Nylon SCR 10-12 x 3/4* PN HD Type A/AB Washer Flt #10-.220 1D x .500 0D Washer Lock Split #10 Cable Tie
Assy XFMR EMI Assy Game Pwr Supply G-80 Assy Vol Control Block
Assy Harn GND Game Elec. Assy Harn GND Pwr Supply Assy Harn Pwr Game Electronics Assy
Compunent Shelf Assembly 800-3251
‘SEE OETAIL “A"
GAME ELECTRONICS ASSEMBLY DRAWING NUMBER 800-3245
ITEM.NO. PART NO. QTY REQD. DESCRIPTION
| 1 | 420-0747 | 1 | Game Electronics Decal |
| 2 | 600-0089 | 1 | X-Y Interface Cable |
| 3 | 800-0161 | 1 | X-¥ Timing Board Assembly |
| 4 | 800-0163 | 1 | X-Y Control Board Assembly |
| 5 | 800-3 249 | ] | Sound Board Assembly |
| 6 | 800-0378 | 1 | CPU Master Harness Assembly |
| 7 | 800-0282 | 1 | X-Y Video Interface Harness Assembly |
| 8 | 800-0296 | 1 | G-80 Universal Card Cage Assembly |
| 9 | 800-3 252 | 1 | G-80 2716 EPROM Board Assembly |
| WwW | 800-3 247 | i | Speech Board Assembiy |
| 3 | 800-3 250 | 1 | CPU Board Assembly |
800-3245
sGame Electronics Assembly
ITEM 9
G-80 CAGE UNIVERSAL ASSEMBLY
ITEM NO.
Da Fwn a PART NO.
250-0456
250-0499
280-0343 420-0560
800-0105 281-0045-06
281-0001-12
281~0001-06
284-0001-00 QTY _REQD.
oe oe eNO DRAWING NUMBER 800-0296
DESCRIPTION
G-80 Cage Assembly G-80 Cage Bracket Split Grommet Test Button Decal
6-Slot Master Board Assembly Pan Head Phillips Screw, Type AB, 10- 12 x .375 Lg Pan Head Phillips Machine Screw, #4-40x3 /4 Pan Head Phillips Machine Screw, #4-40x3 /8 Flat Washer, #4
800-0296
G-8U Cage Universal Assembly
6 SLOT MASTER BOARD ASSEMBLY DRAWING NUMBER 800-0105
qry IT1EM NO, PART NO. REQD. DESCRIPTION RCF OCS.
| 1 | 370-0209 | 1 | PC Board | |
| 2 | 211-0063 | 6 | Conn Card Edge 86 Pin | |
| 3 | 212-0020 | 1 | Conn M RTA 10 Pin | |
| 4 | 151-0059 | 4 | Cap Cer .001 uf i6V AX | C1-c4 |
6 Slot Master Board Assembly 800-0105
Cl —
:
: 6 a cr “H oo Fm
CONNECTOR GRACKET ASSEMBLY DEARL RG AUMBLH QUU-LISKU
ITEM NO. PART NO. QTY REQD. DESCRIPTION
| 1 | 250-0495 | 1 | Bracket Connector |
| 2 | 420-06 26 | 1 | Decal Connector Bracket |
| 3 | 800-0278 | 1 | Assy Harness Video XY |
| 4 | 800-0379 | 1 | Control Interface Harness Assy |
Connector Bracket Assembly 800-0380
CPU BOARD ASSEMBLY
ITEM NO. PART NO.
316-1611
315-0082
800-0107 ary REQD. DRAWING NUMBER 800-3250
DESCRIPTION RES DES.
IC EProm 2716 u25
Chip 315-0082 Assy CPU Board
CPU BOARO ASSEMBLY
ITFM NG. PART NO.
1 150-0088
2 151-0005
3 151-0012 4 151-0020
5 151-0060
6 151-0061
? 170-0194
8 211-0008
9 212-0098
10 230-0013
VW 314-0001
4 SV4-UGIS
3 314-0018
14 314-0019
15 314-0055
6 314-0058 7 314-0062
18 314-0066
19 314-0067
20 314-0068
21 314-0078
22 314-0083 23 314-0085
24 314-0087 25 314-0093
26 314-0099
a7 314-0105
28 315-0041
29 315-0046, Qry
REQD.
“ae aww
nn
Oo wen pe aoe BRI
bow ew oo w oH DESCRIPTION
Cap E 10 uf 25V
Cap CER 680 pf SOV Cap CER .1 uf 50V Cap CER 33 pf 50V Cap CER | uf 16V AX
Cap CER 220 pf I6V AX
PC Board Conn Pin Test PT
Conn M 10 Pin RTA
XTAL 8.000 MHZ
IC NES55
Ic 7404
IC 74LS00
Ic 74Ls04
IC 74L$244
IC 74LS08 IC 74LS74
1G /4LS27
IC 74830
IC 741932
IC 74.802
IC 74LS240 IC 74LS14
Tc 74.8139 IC 74LS3 74
IC 748245
IC 74.5253
IC 280A
IC 2014 DRAWING NUMBER 800-0107
REE DES.
C43, €46, C62
c50 c47
cay
€37-C42, C44, C48, C6T-C61, C63, CEN C1-036
TPI-TP4
yl
ui2
use
U6, U8, Ul4, Ul9 uls
U34, U36, U38
Ul3 ulo, UIT, UI7, U20, UB9
ul6
U37
UB2, U33
U23
ua
u7, U3] u24
U3
U35
ui, U2, US, UY
U26-U29
CPU BOARD ASSEMBLY~Cont inued
ITEM_NO. PART NO.
3t 3 lb-0 /04
33 390-0003 34 471-0101 35 47-0102 36 47)-0103 37 471-0104 38 471-0122 39 471-0220
40 471-0221
4] 471-0331
42 477-0002 43 481-0001
44 481-0006 45 482-0006
46 482-0010 47 482-0014 48 §10-0052 AD 510-0053 50 213-0001
51 213-0002 52 213-0004
53 213-0005 54 510-0049 55 471-0472
56 280-0420 57 471-0473
58 161 0031 Qry REQD. DESCRIPTION
IC 2516 (2716) 1C Prom 3 2x8
Led Red Res 100 Ohm 1/2W 5%
Res 1K Ohm 1/2W 5% Res 10K Ohm 1/2W 5% Res 10K Ohm 1/2 5% Res 1.2K Ohm 1/2W 5% Res 22 Ohm 1/2W 5% Res 220 Ohm 1/2W 5% Res 330 Ohm 1/2W 5%
Res Pack 15x2.2K Diode 1N4002 Diode 1N914/IN4148 XSTR 2N4403
XSTR PE8050 XSIR 2N4401 SWITCH PIANO DIP Su Pushhuttan Side PCM
SKT 24 Pin Dual INLN
SKT 18 Pin Dual INLN SKT 16 Pin Dual INLN
SKT 40 Pin Dual INLN Switch 8 Pos Dip Res 4.7K Ohm 1/2 5%
Gard Ejectur, Snap On Res 47K Ohm 1/2 5%
Cap CFR .22 uf 16V DRAWING NUMBER 800-0107
REE DES.
ves
UIs
n3
~ RS
R1, R3 R6
R7, RB, R22 Rig
R14
R2, R4, RR R10, R11, R15-R20
RP1-RP3 D1, D2 D4 qQ7 Qi, a2 Q3-96, 0 Swi
Sua xu25 XUZ6- XU 29 xu15
XU2T, XU22 swe
R2l
Ro
c45
800-0107
CPU Board Assembly
7 ste WOU u' Uoooo VOY a do 4 OH sf) Ose Lene | be a. OOM Oo = As aero 000 UU ik at ~ sn an batt wt baee af i gs 6088 - id
2716 EPROM BOARD ASSEMBLY
ITEM NO. PART NO.
316-1586
316-1587 316-1588
316-1589
316-1590 316-1591 316-1592
316-1593 316-1594
316-1595 316-1596
316-1597 316-1598
316-1599 316-1600
316-1601 316-1602
316-1603 316-1604
316-1605
316-1606
800-0151 QTY REQD
q
q
J
q
i DRAWING NUMBER 800-3552
DESCRIPTION
IC EPROM 2716
IC EPROM 2716
TC EPROM 2716 IC EPROM 2716
IC EPROM 2716 TC EPROM 2716
IC EPROM 2716
IC EPROM 2716
IC EPROM 2716
IC EPROM 2716 IC EPROM 2716
IC CPROM 2716
IC EPROM 2716
IC EPROM 2716 IC EPROM 2716
IC EPROM 2716 IC EPROM 2716
IC EPROM 2776
IC EPROM 2716
IC EPROM 2716
IC EPROM 2716
Assy 6-80 2716 PROM Board REF DES ~
vi
u2
U3 U4
us
u6é u7 us
ug
ul0
ull
ulz
u13
ul4 vis
ui6 ul7
ul8 ulg
u20
ual
&-80 2716 EPROM BOARD ASSEMBLY
ITEM NO. PART NO.
161-0058
151-0060
170-0211 213-0001
314-0055 314-0058
314-0059 314-0104
314-0120 211-0008 150-0088
280-0420 Qry REOD.
a woe ww DRAWING NUMBER 800-0151
DESCRIPTION
Ceramic Capacitor, .0] uf, T6V AX
Ceramic Capacitor, .1 uf, 16V AK
PC Board 24-P in Dual Inline Socket
Te 7418244
IC 74L$08
Te 741810 IC 7415136 TC 7415154 Test Point Connector Pin
Electrolytic Capacitor, 10 uf, 25V Card Ejector, Snap On REF DES.
Cz, C4, C6, C8, C9, cil, Ci4, C16, C18, Cat, C23, C25, C27 Cl, 63, C5, C7, ClO, Clz, C13, CIS, C17, C19, C20, C22, C24, C26, C28
XU1-XU23
U25
U26-U28 v29
ee) u24 TP1-TP3 C2o
G-80 2716 EPROM Board Assembly 800-0151
| a " L pi _] = ete | Ld fe be ee | 4 = fn ee ray‘ To LJ
2 PLES
X-Y CONTROL ASSEMBLY DRAWING NUMBER 800-0163
gry ITEM NO. PART NO. REQD. DESCRIPTION REF DES.
| 1 | 150-0088 | | 1 | Cap — 10 uf 25V | C23 |
| 2 | 151-0002 | 1 | Cap Cer 100 pf 50V | ci4 |
| 3 | 151-0058 | 21 | Cap Cer .01 uf I6Y AX | C1-C13, C15-C22 |
| 4 | 170-0219 | 1 | PC Board | |
| 5 | 212-0101 | 1 | Conn 4 Pin M RTA | |
| 6 | 213-0001 | 1 | SKT 24 Pin Dual INLN | XP |
| 7 | 280-033 0 | 2 | Card Ejector | |
| 8 | 314-0018 | q | 1¢ 74LS00 | u40 |
| 9 | 314-0019 | 3 | IC 74.804 | U9, 2, 42 |
| 10 | 314-0040 | 1 | IC 7408125 | U39 |
| 11 | 314-0055 | 7 | IC 74.8244 | U2U, UZI, W5, Wo, |
u48, U49, U54
| 12 | 314-0058 | 1 | IC 74LS08 | U37 |
| 3 | 314-0059 | 2 | 1C 74LS10 | U18, U4l |
| 14 | 314-0060 | 1 | IC 74LS20 | USO |
| 15 - 314-0062 | 2 | IC 74LS74 | ul9, U5i | |
| 16 | 314-0067 | 1 | IC 74L830 | U47 |
| 7 | 314-0068 | 2 | IC 74L832 | U4, U38 |
| 18 | 314-0074 | 3 | IC 74LS191 | U15-UI7 |
| 19 | 314-0075 | 1 | IC 74L5393 | uez |
| 20 | 314-0078 | J | Ic 74502 | U23 |
| a1 | 314.0087 | 1 | IC 74LS$129 | uae |
| 22 | 314-0093 | 2 | TC 7418374 | u2, U13 |
| 23 | 314-0097 | 5 | IC 74LS161 | Ul0-U12, U34, U52 |
| 24 | 314-0099 | 1 | Ic 74LS245 | ul4 |
| 25 | 314-0101 | 1 | IC 7418283 | U33 |
| 26 | 314-0108 | 1 | IC 74LS107 | US3 |
| 27 | 314-0127 | 1 | IC 74L$164 | u3 |
| 28 | 314-0128 | 4 | IC /4LS95 | U6, U7, U44, U4d |
| 29 | 314-0137 | 2 | IC 74LS09 | ul, U5 |
| 20 | 3215-0046 | a | Tc 2134 | U24-U31 |
A-¥ CUNTROL ASSEMBL Y~Cont inued
ITEM NO. PART_NO,
315-0072
471-0123 471-0472
471-0622 481-0006 213-0002
471-0471
471-0103
471-033 2
471-0512
482-0006 482-0014 qry REQD.
sey BHT wo aw usa DESCRIPTION
1c AM 4
Res 12K Ohm 1/Aw 5% Res 4.7K Ohm 1/2W 5% Res 6.2K Ohm 1/2W 5% Diode 1N914/1N4148 Socket 18 Pin
Res 470 Ohm 1/2W 5% Res 10K Ohm 1/2 5%
Res 3.3K Ohm 1/2W 5%
Res 5.1K Ohm 1/2W 5%
XSTR 2N4403
XSTR 2N4401 DRAWING NUMBER 800-0163
REF DES.
U8, U43
R1, R38, RS R7
R2, R4, RE Dt-D6
XU24-XU31
RB
Ro
R11
R10
gz
800-0163
X-Y Control Assembly
cal
—] é La]
‘ PLACES,
X-¥ TIMING ASSEMBLY
ITEM NO. PART NO.
1 151-0005 2 151-0058 3 170-0218
4 211-0008 5 212-0101
6 213-0001
7 213-0004 8 213-0010
9 230-0009 10 280-0330
1 313-0004 12 313-0044
13 314-0018 14 314-0019
15 314-0040
16 314-0046 V7 314-0055
18 314-0058
19 314-0062
20 314-0070
al 314-0073 22 314-0074 23 314-0076
24 314-0078
25 314-0093
26 314-0097
27 314-0101
28 314-0108 29 314-0120
30 314-0135 Quy
REQD.
q
OS) nn
TNs M eH DWH DADE Www
Sl a a DESCRIPTION
Cap Cer 680 pf S50V Cap .01 uf 16V AX PC Board
Conn Pin Test PT Conn 4 Pin M RTA
SKT 24 Pin Dual INLN
SKT 16 Pin Dual INLN
SKT 8 Pin Dual INLN
Xtal 15.46848 Card Ejector
TC LM7410N Dip IC AD561
IC 74LS00 IC 74LS04
TC 74L8125
IC 74504
TC 7418244
IC 74LSs08 IC 74.874
IC 741886
TC 74L8175 IC 741191
IC 74L$157 IC 74LS02
IC 74.5374
IC 7418161
IC 74.8283
TC 74L5107
IC 7418154
Ic 74.si1 DRAWING NUMBER 800-0161
REF DES.
c7
Cl-C3, C6, C8-Cze
TP}
XPI, XU39, XU50 XU1, XU4 XU2, xuU3 a
Ud, Us ul, U4 u28
U30, U40 u27
ui4
US4, U57, US8 un, 27 U25, U26, U42, U43, us2
u29 U3 §-u3 8 U15-U20
U5-U10 u53
u48, U49, U55, US6 U31-U84, U4], USI ud4-u47
UIT, u22-U24 us
ule
X-¥ TIMING ASSEMBLY Cont inucd
ITEM_NO. PART_NO.
315-0019
471-0202 471-0331
471-0392
475-0024 151-0008
150-0088 151-0042
481-0006 151-0002 ary
REQD.
NN MANNY WKH | DESCRIPTION
IC 2708
Res 2k Ohm 1/2W 5% Res 330 Ohm 1/2W 5%
Res 3.9K Ohm 1/2W 5% rot 1K lu turn
Cap Cer .001 uf 50V
Cap E 10 uf 25¥ ROL Cap, Cer 470 pf 50V 1N914 Diode Cap Cer 100 pf 50V DRAWING NUMBER 8UU-U107
REF DES.
1B9
R2, R4 R7, R8
R1, RS R3, RO
C29, C30 c4, C5 c31
DI, D2 C32, €33
800-0161
X-Y Timing Assembly
f * J is a jy
an oS t stra ss po a i-4
; i,
SPEECH BOARD ASSEMBLY ORAWING NUMBER 800-3 24/
| ITEM NO. | PART_NO. | QTY REQD. | DESCRIPTION | REF DES. |
| ] | 316-1607 | 1 | IC EProm 2716 | u7 |
| 2 | 316-1608 | 1 | IC 2732 | U6 |
| 316-1609 | 1 | IC 2732 | Us | |
| 316-1610 | 1 | IC 2732 | u4 | |
| 3 | 800-0294 | 1 | Assy 2732 Speech PCB |
SPEECH BOARD ASSEMBLY
ITEM NO.
ae wn PART NO.
150-0087
150-0088 151-0021
151-0056 151-0058
151-0060
170-0223
212-0012
230-0033
280-0420
313-0037
313-0038
314-0058
314-0062
314-0067
314-0072 314-0085
314-0087
314-0100
314-0042 214-0131
315-0061
315-0077
315-0079
316-0788 471-0103
471-0106
471-0222
471-0223
A7)-0274 QTY
REQD.
a Se 5 ee DESCRIPTION
Cap — 4.7 uf 25V
Cap — 10 uf 25¥ Cap Cer 20 pf 50V
Cer .047 uf 5oV Cer .01 uf 16V AX Cap Cap
Cap Cer .1 uf 16V AX PC Board Conn 6 Pin M
Crytral 3.12 MHZ Card Cjector I¢ TLO81 CP
IC TLO82 CP
IC 74LS08
IC 74.874
IC 74LS30
IC 74LS174 IC 74.814
IC 7418139
IC 748273
IC 7406
TC 71 $272
IC ST-32034
IC 8035
IC CD4053
IC Prom Speech Bd Decoder Res 10K Ohm 1/2W 5%
Res 10 Meg Ohm 1/2W 5% Res 2.2k UNM 1/2W 5% Res 2 Ohm 1/2W 5%
Res 270K Ohm 1/2W 5% DRAWING NUMBER 800-0294
REF DES.
C2
C13, C46-c49
- C6, C7
cin c5, Cll, C12, C14- 17, C19, C20, C44 C9, C37, C38
yl
Snap On U8
ull
U35
u15
U37
u20
U38
ul0
u2l
ul3
ua
U2
ul4
ule
U30 R17, R21, R27-R29 R3
R24
R13, R14, R18, R22 R19
SPEECH BOARD ASSEMBL Y-Cont inued
Qry
ITEM. NO. PART NO. REQD.
| 31 | 471-0471 | 2 |
| 32 | 477-0002 | 1 |
| 33 | 471-0683 | 1 |
| 34 | 475-0022 | 1 |
| 35 | 151-0009 | 1 |
| 36 | 471-0472 | 1 |
| 37 | 21 -0001 | 9 |
| 38 | 213-0004 | 1 |
| 390 | 213-0005 | 1 |
| 40 | 213-0008 | 2 |
| 4 | 213-0010 | 2 |
| 42 | 213-0012 | ] |
| 43 | 471-0102 | i |
Res
Res
Res
Pot
Cap Res
SKT
SKT
SKT
SKT
SKT
SKT
Res DESCRIPTION
470 Ohm 1/2W 5%
Pack 15x2.2k
68K Ohm 1/2W 5%
100K 10T PC MNT Cer .003 uf 100V
4.7K Ohm 1/2 5%
24 Pin Dual INLN
16 Pin Dual INLN
40 Pin Dual
20 Pin Dual INLN
8 Pin Dual INLN
28 Pin Dual INLN
1K Ohm 1/2W 5% DRAWING NUMBER 800-0294
REF DES.
R25, R26
RP2
R30
R74
R20
XU3- XU?
xU30
xa
XU9, XUZT
xus, XU1]
xu2
R75
800-0294
Speech Board Assembly
5 ll 4 as “S =
a@ He) ce a a cS ée A
SOUND BOARD ASSEMBLY DRAWING NUMBER 800-3 249
Qiy ITEM NO. PART NO. REQD. DESCRIPTION REF DES.
| 1 | 150-0087 | 2 | Cap E 4.7 uf 25V RDL | Cl, C38 |
| 2 | 150-0088 | 4 | Cap E 10 uf 25V ROL | C4, (8, (237, C73 |
| 3 | 150-0090 | 1 | Cap E 33 uf 25V ROL | C56 |
| 4 | 150-0099 | 1 | Cap — 1 uf 50V | C35 |
| 5 | 150-0100 | 2 | Cap E 2.2 uf 50V | C21, (36 |
| 6 | 151-0001 | 4 | Cap CER .05 uf 50V | C51, C48, C50, C52 |
| 7 | 151-0002 | 1 | Cap CER 100 pf 50V | c63 |
| 8 | 153-0008 | 1 | Cap CER .001 uf 50V | c60 |
| 9 | 151-0012. | 33 | Cap CER .1 uf 50V | C2, C3, C5, C6, |
Cl2, C22-c29, C31, C32, C39-C41, C44, C45, C49, C53, C57 C59, C62, C64, C70- (72, €74-C77
| 13 | 152-0001 | 8 | Cap F .1V uf 100V | C3, Ch4, C33, C34, |
C54, (55, C58, C69
| 14 | 152-0005 | 1 | Cap F .0047 uf SOV | cs |
| 15 | 152-0007 | 1 | Cap F .001 uf 250V | c7 |
| 16 | 152-0010 | 2 | Cap F .022 uf 100V | C30, C66 |
| 7 | 152-0035 | 1 | Cap F .033 uf 100V | c43 |
| 18 | 152-0037 | 9 | Cap F .068 uf 100V | C10, C11, ¢15-C20, |
C61
| 19 | 152-0038 | 3 | Cap F .047 uf 100V | C47, C67, C46 |
| 20 | 152-0039 | 2 | Cap F .O1 uf 100¥ | C65, C68 |
at
| 2? | 17N-0734 | ? | PC Raard Sound Eliminator | |
| 23 | 272-0107 | 1 | Conn 4 Pin M RTA | |
| 24 | 213-0012 | ] | SKT 28 Pin Dual INLN | XU30 |
SOUND BOARD ASSEMBLY-Cont inued
TTEM_NO.
au PART NO.
280-0420
313-0005 313-0037
313-0038 313-0046
314-0001
314-0018
314-0040 314-0042 314-0043
0059
314-0062 314-0067 -
314-0085 314-0093
315-0007 315-0035
315-0043
315-0052 315-0049
471-0102
471-0103 Qry
NaS Sw OW Bu
ra} DESCRIPTION
Card Ejector Tf | MSA6CN
IC TLO81
IC TLO82 IC CA3080E
TC NE555
TC 74LS00
IC 74L$125
IC 7406 IC 7407
Te 74tso08
TC 74LS10
IC 74LS74 IC 74LS30
IC 74.814 TC 7418374
IC CD4011A
IC M5837
IC CD4069A
Te Co4024a
IC AY-3-8912
Res IK Ohm 1/2W 596
Res 10K Ohm 1/2 5% DRAWING NUMBER 800-3249
REF DES.
Snap On yas
Ul, U3, U12, U29
U2. 16, 1170 U6-U11, U15,; U16 US, U3 U26
U33
ude
U27, U28 wo
U37
WwW6
u40
Ws, U4) U34, U35 U17-U19, U22 U4
U31, U2 U2T, v23 BO
R19, R31, R35. R40, R43, R51-R53, R55- R57, R63, R69, R72, R80, R131
R8, RIO, R17, R18, R20. R22. R44. REO.
SOUND BOARD ASSEMBLY-Continued
ITEM_NO.
f2 PART_NO.
471-0104
471-0105
471-0153
471-0154
471-0155
471-0202
471-0222
471-0223
471-0224 QTy
REQD.
wrnnn
VW DESCRIPTION
Res 100K Ohm 1/2W 5%
Res 1M Ohm 1/2 5%
Res 15K Ohm 1/2W 5%
Res 150K Ohm 1/2W 5% Res 1.5K Ohm 1/2 5%
Res 2K Ohm 1/2W 5%
Res 2.2K Ohm 1/24 5%
Res 2X Ohm 1/aW 5%
Res 220K Ohm 1/2W 5% DRAWING NUMBER 800-3249
REF DES.
R76-R78, R94, RIS, Rag, R1NO, R105, R126, R134, R135 RB7, RBS
R1, R15, R16, R21, RG7, RGB, R111, R114, R118-R120, R123, R125, R144, R71, R132
R2, R12, R91, R93, R113, R115-R117
R90, R104 R64, R75
R26, RAl R47, R54, R59
R4, R11, R84-R89, R109, R110, R147
R3, R30, R34, R39, R46, R50, R9Z, RIO, R127, R130, R146
R6, R7, R25, R62, R141
SOUND BOARD ASSEMBLY- Continued
ITEM_NO.
ral PART_NO.
471-0225
471-0274
471-0323
471-0334
471-0393
471-0394 471-0471
471-0472 47\-U473
471-0474
471-0681
471-0682
471-0683
471-0684
471-0823
471-0911 471-0912
471-0123
481-0001
481-0006
482-0006
482-0023 QTy REQD.
an
PS Se CR od
wee ew ow DESCRIPTION
Res 2.2M Ohm 1/2 5%
Res 270K Ohm 1/2W 5% Ras 33K Ohm 1/ aM AX
Res 330K Ohm 1/2W 5% Res 39K Ohm 1/2 5%
Res 390K Ohm 1/2W 5% Res 470 Ohm 1/2W 5%
Res 4.7K Ohm 1/2W 5% Res 47K Otm 1/2W 5%
Res 470K Ohm 1/2W 5% Res 680 Ohm 1/Mi 5%
Res 6.8K Ohm 1/2W 5%
Res 68 Ohm 1/2 5% Res 680K Ohm 1/2W 5%
Res 82K Ohm 1/2W 5% Res 910 Ohm 1/2W 5% Res 9.1K Ohm 1/20 5% Res 12K Ohm 1/2W 5%
Diode 1N4002
Diode 1N914/1N4148
XSTR 2N4403 XSTR 2N4093 NRAWTNG NUMBER 800-3249
REF DES.
Rat, R42, R112, R121, R124
R140
RAR, R3BB. R49. RSB.
R66
R13, RI39, R142 R97, R128 R65, R74, R1ZZ R82, R83 R23, R107, R108, R5 R32, R45, R61 R14, R26, R27, R70
R133
R37, R48, R102
R29, R145 R73, R106, R136, R143
R33, R98, R129 R101
R103 R9
01-07
Q2-Q1 Qi
Sound Board Assembly 800-3249
Y mb ee “Ee iE . = Bas oo® aie a5 —0 igo te = 2 = oJ 5p 8, ale g 5 Ss sec fei ag 7 7 « Brea Las oS (STH = seit Be aa ae m sedi, ts gs men A. BSG ABER Ea ee en
B-RN PAWFR SIPPILY CHASSIS ASSEMBLY DRAWING NUMBER 800-0191
Qry
| ITEM NO. PART NO. | REQD. | DESCRIPTION | REF DES. |
| 1 | 530-0016 | 1 | Heat Sink, G-80 Pwr Sup. |
| 2 | 250-0460 | 1 | Chassis Support |
| 3 | 250-0461 | 1 | Cover |
| 4 | 800-0170 | 1 | PCB Assembly |
| 5 | 753-0206 | 6 | PCB Support, Threaded |
| 6 | 281-003 2-06 | 8 | Thread Forming Screw, #6 |
Type B, 3/8 long
| 8 | 482-0104 | 1 | Power Transistor | TIP 141 |
| 9 | 313-0023 | 1 | Negative 5 Volt Regulator | 320T5 |
| 10 | 313-0014 | 1 | Positive 12 Volt Regulator | 340712 |
| iW | 313-0015 | | | Negative 12 Volt Regulator | 320T12 |
| 12 | 482-0100 | 1 | Power Transistor (Audio | TIP 125 |
Amp)
| 13 | 482-0019 | 1 | Power Transistor (Audio | TIP 120 |
Amp)
| 16 | 420-0557 | 1 | Fuse Decal |
| VW | 280-0117 | 1 | Tab Rivet Male 1/4" |
| 18 | 420-U5/5 | i | Power Supply B Decal |
| -0001-08 | 6 | Pan Head Phillips Screw, |
4041/2" Ly
| 20 | 280-03 41-00 | 6 | Shoulder Washer, #4 |
| ral | 310-0006-01 | 6 | Transistor Insulator, TO-220 |
| 22 | 284-0003 -00 | 6 | Flat Washer #4 |
| 23 | 284-0031-00 | 6 | Split Lock Washer #4 |
| 24 | 283 -0021-00 | 6 | Machine Hex Nut, 4-40 |
| 25 | 800-0243 | 1 | 6-80 Transistor Harness |
Assembly, Pl
| 26 | 800-0244 | 1 | G-80 Transistor Harness |
Assembly, PZ
G-80 POWER SUPPLY CHASSIS ASStMBbLY-Continued
ITEM_NO. PART_NO.
800-0245
800-0246
800-0247
800-0248
310-0007-01 qry
REQD. DRAWING NUMBER 800-0191
DESCRIPTION REF DES.
G-80 Transistor Harness
Assembly, P3 G-80 Transistor Harness
Assembly, P4 G-80 Transistor Harness Assembly, P5 G-80 Transistor Harness
Assembly, P6 Transistor Insulator "H", T0-218
G-80 Power Supply Chassis Assembly 800-0191
Sei FANG)
G-80 POWER SUPPLY PC ASSEMBLY DRAWING NUMBER 800-0170
qry ITEM NO. PART NO. REQD. DESCRIPTION REF OES.
| q | 150-0088 | 9 | Electrolytic Capacitor, | c5, C8, C10, C18, |
10 uf, 25V C19, C23, C24, C26, ~ €31
| 2 | 150-0092 | 1 | Electrolytic Capacitor, | C7 |
100 uf, 25V
| 3 | 150-0095 | 1 | Electrolytic Capacitor. | 30 |
3300 uf, 25V
| 4a | 150-0096 | 3 | Electrolytic Capacitor, | (3 2-034 |
6800 uf, 16V
| § | 150-0097 | 4 | Electrolytic Capacitor, | €15, C16, C27, C28 |
4700 uf, 25V
| 6 | 151-0002 | 1 | Ceramic Capacitor, 100 pf, C9 |
50V
| 7 | 151-0007 | 1 | Ceramic Capacitor. .005 uf, C20 |
| 8 | 151-0011 | 4 | Ceramic Capacitor, .01] uf, C21, C22, C25, C29 |
50V
| 9 | 151-0012 | 3 | Ceramic Capacitor, .1 uf, | c2, C3, C14 |
50v
| 1 | 151-0021 | 1 | Ceramic Capacttor, 20 pr, | cr |
Sov
| 1 | 170-0222 | 1 | PC Board | |
| 12 | 212-0020 | 2 | 10-Pin Male Connector RTA | |
| 3 | 212-0081 | 2 | 4-Pin Male Connector RTA | |
| 14 | 313-0001 | 1 | JC tM723 Dip | ul |
| 15 | 471-0011 | 1 | Resistor, 10 Ohm, 1/2W 5% = R2 | |
| 16 | 471-0101 | 1 | Resistor, 100 Ohm, 1/2 5% R32 | |
| 7 | 47-0102 | 3 | Resistor, IK Ohm, 1/2W 5% | R10, R27, R29 |
| 18 | 471-0103 | 2 | Resistur, 10K Ohm, 1/2 5% RG, RIO | |
| 19 | 471-0104 | 1 | Resistor, 100K Ohm, 1/2W 5% R23 | |
| 20 | 471-0222 | 2 | Resistor, 2.2% Ohm, 1/2 5% R21, R22 |
G-80 POWER SUPPLY PC ASSEMBLY-Continued
ITEM_NO. PART _NQ.
471-0223
471-0332
471-0182
471-068) 473-05R0
473-00R2
475-0004
481-0002
481-0004 48} -0006
482-0006
482-0014
§14-0002 514-0003
514-0006
514-0008
800-0791 471-0220
471-0221 QTY
REQD.
° —~ ee et eOnNnnn w DRAWING NUMBER 800-0170
DESCRIPTION REF DES.
Resistor, 22K Ohm, 1/2W 5% 5, RY
Rasistar, 2.2K Ahm, 1/2 5% RIA Resistor, 1.8K Ohm, 1/2W 5% R26 Resistor, 680 Ohm, 1/2 5% = R7 Resistor, .05 Ohm, 5W 3% R25 Resistor, .2 Ohm, 3W 5% R14, RIS Pot 1K Car PCMTV R31
Diode MR75} DIO, 012 Diode MR5OT “ DG-D9, P11, D13-D17
Diode 1N914/1N4148 D1, D4, DS Transistor 2N4403 Qi. a7 Transistor 2N4401 Q2, Q3 Fuse 3A Norm Fl, F2 Clip Fuse Mounting Fuse 1.5A Norm Fa Fuse 10A Slow Blow F3
Schematic Reference Resistor, 22 Ohm, 1/al 5% RR Resistor, 220 Ohm, 1/2W 5% R33
G-80 Power Supply PC Assembly
800-0170
Ca} ©) _ a §oH ee a IC) fle
# ann -nzan P/) 800-3251 # 800-0285
P/O 800-3251 # 800-0286
alk
PROM = 80D - 3252
2716
ra
' 9) PWR Yo o3 5 [26070001 |} 4 ao0- 800 - O19 ‘ 300-0322 ° bd 0 | S 8 a PS ws x an a 58 [ie Ke r Pz S|
| x= | ay | Rep | L____Jel |
| 800-0975 | Cy | BLK | qd |
| } | 45 | t]rpP RED | La |
wekaeys fey YO lata | RED 313 BL |3|2 yeu |2|2 war
Pg
P/O 800-0380 +# 800-0278 fa
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
4,00 VOLUME jest 28.00 Fil
SERVICE r* ‘ rus
vio 9.00 229] . ;—* neo vou fea) |* NO “NC BLK 9.00 [229] :
- YEL 10.00 [254] | CONN MEWED WIRING END Volume Control Block 800-0277
‘TO TRANSFORMER
JUNCTION BOX SCHEMATIC A. C. Junction Box 800-0145 ALTERNA FOR 800-0 HA
WHT/BLK WHTIGRN WHT/RED
WHT/RED.
XF MR
ALTERNATE WIRE COLOR CODING ‘OR 800-0379 CONTROL INTERFACE HARNESS ASSEMBLY
WHT/BLK WHT/GAN
WHT/RED WHT/BLU Pwr DOUU ITEMS 2Pl Sag BLK 3.00 76
ORN ¢ WHT
ORN
WHT / BLK WHT
BLK
Transformer EMI 800-0190 CONN VIEWED FROM WIRING END RED % RED / BLK 5
RED Ke 8 ¥IO 5 ag }e 6R _[ BK 3.00 76 ‘ vio BRN ; BRN / BLK
on
PIO 1418244 F3C
ua R2 ant
ua RB 5 oe 1K 74L 314
FIRE
THRUST
THRUST
FIRE
2 PLAYER
- 0 | PLAYER
REF ONLY
Z\ tia PEL SI4
er jez +bes -OIpf all cea
P4L SIF
Single Player Control
Panel Interface 800-0974
SEL BNT 10 PIN CONN. Pi SEL BNT
SEL BN/T I 86 PIN CONN.
TYP P2 THRU P7
6 Slot Master Board 800-0105
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
REVISIONS. 1 a a Ean oe | [=| See SHT / a ee
NOMENCLATURE OR DESCRIPTION PARTS LIST
DIMENSIONS ARE IN INCHES
FOCERANCES ARE:
CODE IDENT NO. [DRAWING NO. REV B 800-0382 A score NONE] [ster Foor 4
Model Number
NOLES OMEFWEEE CORO] CD ELIE TANCE aK Attn | SERBS ! PERE ao conan i GES CE RE AUN aren EN era a
Loe
Fe ray
ai 5 |
mber GO&-003 00-4177-04
19” X-Y Color Monitor 200.0025
YI BDOIMAZ
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
De (SHT 6)
82 OUT 37! fare) 25 (SRT 6) ) 7 ces AB il PF [220 4 [2 Yiyes fad Pe al @(SHT 6) Aw) R2 2200 a I 'Na002
Ra pe agen % wann>
az at Peaoso | I
i§™ 22000.
3 (SHT G)
D2 (GHT 6)
1$* 2200.0,
REVISIONS,
| - | ae] ee | DEScRirTION | DATE] APPROVED. | |
| ry | cTc | 10-28-BO} A. BRON: | ||
| Bi ECON #528 | CTS | hi -\s-Se | ||
| ot | cLECN | 2 | ic | PE |
| DT ECN¥Gr77A | CTS | [aah | zi | |
| aa) | & | PER ECw e978 | MGA | |p3121 | tmout |
Fal +, EEG SHT | FOF Rl a8 ‘Naoo2 2. D
at Tazo. PEBOSO
v2 oe 1270 inagoe [?7Sp
a2 Tazo Ee PESOSO | PF v
c
eer (ae : s\, 7 DS (SHT 8)
3 us 7 B LS253 z D4 (HT 6)
B
w al B Ea R f
n is)
g
Ee Pe Een PARTE LT
| rien | - | ‘Gremlin tadustries, ine. |
eaves bam rege, Cabpores Sarin
| oe te | S | aro | ae | A |
CPU Board 7 says or [oRAWING RO. Rey D 800-0107 F Fer say [Wao on :
| ‘APPOCATION | 10. ROT SEE DRAWING | pene NOME | Ca |
| 4 | 3 | 2 | ' |
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
REVISIONS,
| weF | wT | Tanne | AF | BRITT ee | SESSROTOR | oa reyes |
2 jeo C[ See ST 1 FOR CHANGES [er] 8 24 +5v. 7 AIS Aa g 2 é ‘TYP =) 2 Alo / Ul-ves us 3} uo 2mlé 2 rail tL tz 240-247 23 350-257
wpe? [DROP TaavEpel7
| 200-207 | 210-217 | 220-227 | 230-237 | 240-247 |
| deo | Jeo | _dzo : deo | ‘ deo |
8 Sr
| 7 | i | 7] | z | 7| | c |
| € | B | a | A | a | |
| | | 5 | 5 | S | 5 | |
| gy | 4 | 4 | + | + | |
| 3] ute | 3 wit | 3} vis | 3] us | 3) uzo | |
| 2} ene | z] erie | 2} ero | ze] ere | | erie | |
| H | i | i | q | t | |
| Fa | Fa | 2a | 2 | 2 | |
| 2] | 22 | 22 | ee | 4 |
7 afro spalis pote? fy pofis] is [eee often 7 9 ot ISpeniy | froft i speey sis] 17 19 opt «13 7
| : | = | 4 | I |
ts fu jo fe fr is fe [a ' —— ues BUFFER TaLseaa 2
S19 [te fia JS Jr fz -[i6
OXON NON) DA DI D2 DS D4 DS Be DF
Gremiin Ineustries, ine. San Diege, Catiternie 9223
G-80 2716 EPROM Board SHE [S0sE OMT 1 cracel.ce c2s,ce7.
-Olae
P"g00-0151 | > [sceer 4 oF ¢
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
p45 some or ware
oO —_ hig it) WOE cs THRO C24 6258 ne
| Je Jn | +2,
= | [ue |»
lels
Gremlin industries, ine. sam Biege, Cabtoreia 993
behsl= T e185 ig
REVISIONS +2 Zone [um DESCRIPTION ‘are [ APenovED, BEE Sat Ey
| : | ie | berlabslal tals |
48 jo TALS374 ry
| 13 | n | 2 |
tty H
| iT | a | vse |
sm
| LH | 5 |uze | mL | ||
| + | T | = | C | |
| 4 | iss | t | | | et |
i = FH =e +
| jest | aesaie | | | |
| lela jz pmispal | IS}e]3 2 | papel | |
| 7 | Ss | Cee | 3 |
7ats283 auszes [7 3 To 3 fo
+ aA Blea, — a Has
| 3 use (a_25) | + | rt | 7 |
mus) 9 T
| A | 2 | 7 | I |
| =a | 7 ae TS | t | |
| a3) | hol meu si7s [iz | t | |
| 8] | 15 | | 3 | =r |
T T
| SBE Totti, | PE 7 7 Gremiin industries, inc. San Diego, Camtormin 02923,
X-Y Timing Board
BRAVA WO. 800-0161 | 300-2155] 7)00-9554 HET ABBY ‘USED. ON [APPLICATION DO NOT SCALE DRAWING 3 2
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
REVISIONS Bele DescRWTION gee sons sa oe > T
S went
vou, | is) vou,
7 a
Bue —s oi
5 3 L802 aoe 2 uss)"
=
Tee Re BIMERSKs A we
X-Y Timing Board
[SO0E IDENT Wa: DRAWING WO REV 800-0161
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
Ieageres vay nt + halal aero |
r th & aa) +s 7ais08 | ne of 0 Bo, Be Le mo
manne ae
Yo sHT=
com
mises fiz | 7aLstet Z| ue [B 3] us " ue age
© = Be PIN CONNECTOR . © + +m wae © = 200m sore NOTES ¢ 7 | “6 | 5 f Te)
REVISIONS Ei DESCRIPTION See enh)
MLTIPLY ctx (17) Do
ry oe ie as04 slr! 45 +5 tt le C 2, IS 45 22 3 Io} Prasiet mite a usz «tus [8 ac}
“a
Te nt 3 cos 07 bls{7/sisel7|ia
7aLS374 uz
EE Se aere c +s tat * cre c15- G22 sol pd fot
2 tS
at 2N4403
Ro 10K
Gremiin industries, inc. Rae Ringe, fatiternin One
X-Y Control Board
USED OF [APPLICATION DO _NOT SCALE DRAWING
wai
Ae 3 ee nO s
THRUST MSS TH RUeT LSB THRUST
use Ng2
P4e5l6 Fat gio. vas esa7e
V5 caper. vas LA ewe weesare| 2 givens S— pou je Tore Stare
7a
Chet ers FE slp! rz mag cared
a Da Bette inaooz,
wc.
FIRE ALL
EMPL MIEN
ExrtoSt0n 2 BArCOBION 3 baer a aoUNce TORPEDO 1
TORPEDS
OMENCUATURE RY CESERIPTON PARTS UIST Gremlin/seca Erber Golena she
Sound Board
SE [COE BENT WO TORARINE NO aT D 800-3249 APPLICATION.
32 uaz Pot q—2D Soba zooms a
| CO40GF | C040eo | SAT? |
D R142 330K Cas
want Pica u32 uaz
| BN! | a | zeowe @ |
| CO4t0eF | cD8069 | sata |
R139 sone
Dink eds we, use exPe
- ‘Br choos Tooke Riss BOK:
R187
Pie Ot TE
ebeon a eosona
TORPEDO | ZN 403, BHT 7
EXPLOSION 3 ane ,
REVISIONS DESCRETON DATE | APPROVED SEE SHT AT HEA. f L
Som ved SNT 7
ALBie OUTPUT
cod ona TO ITA one
eneascrs, |, feue 7! czycszjce 163 C7O-C72 olat en
63,022,024, 26,0 34690 ial
t+ - 12 tout 800~ 3249
casoua codon
css
1DO_ NOT, SCALE_ DRAWING.
H aa we r)
| 1508 | se AIS | Tae 7g aI |
| +S & | P25 | —? |
ants “el peg [35 _AI2 1530 it 15! RP2
| Ot | Rea. | ul4 | |
| AS &— 4 | is | Se] ay2 17 OS | 8035 |
| 3 | is] lad bs | N.C, |
At pb A P23 + 13 AS 3 NG. ip uso FTE * PSER JAZ bs wh, oat ees 5516 rzz !Olag f2)
| iad | pez | P20 |
ALE +5 ig
ry 20 |i
| oe 3 | 2 | 27 |
Pio pista als al) Piz psa] Uz! [a 30] 12
| D4 3 | i2 | 37 + |
p5_14| 5273 [is EH ce 17), Ii 3365
| 9718 | 1S | a] "6 | oe |
a D1
| ie Yt | +5 2m als | me | |
| Ra? | es | Re | |
| 6 5s | 1K | aera | DS |
Res Yi ee is tox | azo gt tee Tee
| ors | 5 | RESET 1/38 | 5 Oe |
| p26)” y2o°lz | ipo | wale Spt S) oaTA PRESENT |
3 iF 70 bai] 43174 fe [> v2 a
Tour cre ovr INSTALL
REVISIONS, SEE SUT! FOR REV
€ +5 F | porre ars 4
| +s | wets | 4 | ||||||
| 20 | 2 | a | [20 | at | iT | 20 | 2t | 1 |
| rr) DEE VPP/AH CESAII ig eee: VPP/AI! CEAATI 3 ee | bata VPP/AIL CEZAT | DERE PPA CEZAI) | ||||||
| 24K 9 | e AS | 2a AS | mez AS | |||||
| 2 AB | AB | Fale | } | AB | ||||
| 4, 34 | v7 | U6 | us | u4 | u3 | |||
| $—31/*7 | PROG | DATA | 247 | DATA | 227 | DAIA | a7 DATA | |
| us fe | } AG | 3 AG | E AG | |||||
| S—aj45 | 2716 | 2716 | aa 2716 | 1A | 27/6 | 2716 | ||
| Ei | s | 5 | ||||||
| = | € AS | ra | ||||||
| 7 | ar | z |
&
| 3 | Lo a9 | i |
RESENT
STALL JUMPERS Gremlin industries, ine. Sam Binge. California 933
PROG DATA Ac | E;67E7K/M; "16" Bc F;S/17K/M; "32" BSo-ca74 B25 -3194-x PON CAT TELL
Speech Board
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
1 4 | 3 2 PI 2, P2 ~aeONE . one] Discmrem Batt“ apensiveb y >AYDIO IN #4 eo yr AUDIO OUT Mt AT RELEASED Cie [pul oe
FOR FUTURE USE
2Na401 Qs,
2 +12V IA STS GND <6 ——_— -rav a 1 P3
I Ee Gremlin Industries, inc. ‘Son Binge, Cabeernan at2 (inal ATTELL 2/1i/aoy
po
G-80 Power Supply
"REV 800-0191 DO NOT SCALE ORAWING
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
SERVICE NOTE SEGA / Crem n EFFECT: — zexror
NUMBER: oce 8/9/82
The following lists comprise the Recommended Spare Parts List for the support of 10 games (and presumes the user to a stock of common ICs consistent with a con- Lemporary digital electronic repair tacility):
| ITEM NO. | PART_NO. | qQrTy. | DESCRIPTION | REF. DES. | PRICE |
ASSY ROTARY INTERFACE 800-0382
| 1. | 370-0006 | 2 | XSTR, Opto Electric | US1, DSZ | 5.6U |
Encoder ASSY AC JUNCTION BOX 800-0145
| 2. | 270-0001 | 1 | FILTER, EM] | 20.00 |
| 3. | 514-0001 | 5 | FUSE, 2A 250V S.B. | 1.50 |
| 4. | 514-0051 | 5 | FUSE, 1A 250V | 70 |
| 5. | 514-0053 | 5 | FUSE, 5A S.B. | 70 |
ASSY COLOR X-Y MONITOR 200-0025
| 6. | 481-0211 | 1 | DIODE, Zener 1N75] | ZD903, 904 | -30 |
| 7. | 481-0207 | 1 | RECTIFIER, 1A 1400V | D901 | 80 |
| 8. | 560-0062 | 1 | XFMR, Horiz. Buffer | 7900 | 5.20 |
| 9. | 560-0073 | 1 | XFMR, Horiz. Output | T9301 | 49.20 |
| 10. | 180-0010 | 1 | CHOKE, Horiz. Delay | L900 | 1.60 |
| VW. | 482-0242 | 2 | XSTR, 5A 1400V Power Q900 | 5.50 | |
| 12. | 481-0202 | 1 | RECTIFIER | D400-403 | 6.50 |
| 13. | 481-0020 | 2 | RECTIFIER. TA 200V | 0404 | 40 |
| 14. | 481-0204 | 1 | DIODE, Zener 1N5263B ZD400 | -30 | |
| 15. | 481-0205 | 1 | DIODE, Zener 1N5239B D401 | -30 | |
| 16. | 481-0179 | 1 | DIODE, Zener 9.1V 1H 5% ZD402 | -50 | |
| V7. | 482-0260 | 4 | XSTR, 2N6259 | Q605, 606, | 8.30 |
705, 706
| 18. | 800-0307 | 1 | PCB, Input Limiter | 54.40 |
| 19. | 800-0318 | 1 | PCR, Input Clamp | 16.50 |
ASSY EM1 TRANSFORHER 800-0190
| 20. | 560-0655 | 1 | XFUR, G-80 Power Supply | 120.70 |
SEGA/Gremlin 8401 Aero Drive, San Diego, California 92123 @ Telephone 800-854-1098 (73 &
| ITEM NO. | PART NO. | Qry. | DESCRIPTION | REF. DES. | PRICE |
ASSY CPU BOARD 800-0107
| 21. | 151-0060 | 2 | CAP, O.IMF 16V - € | C37 | 20 |
| 22. | 151-0061 | 5 | CAP, 220PF 16V - C | C1 | 30 |
| 23. | 230-0013 | 1 | XTAL, 8.000 mHz | Yl | 12.00 |
ASSY 2716 CPROM BOARD 800-0151
| 24. | 151-0058 | 2 | CAP, O.O1MF 16V - C | c2 | 20 |
ASSY X-Y CONTROL ROARN 800-0163
| 25. | 481-0006 | 2 | DIODE, 1N914 | o1 | 1.00 |
ASSY X-Y TIMING BOARD 800-0161
| 26. | 230-0009 | 1 | XTAL, 15.46848 mHz | Yl | 10.00 |
ASSY SPEECH BOARD 800-0294
| 27. | 230-0033 | 1 | XTAL, 3.12 mHz | Yl | 4.20 |
| 28. | 315-0077 | 1 | IC, 8035 | ul4 | 10.50 |
ASSY SUUNUD BOARD 800-3249
| 29. | 151-0032 | 5 | CAP, O.1MF 50V - C | C2, 3, 5 | 50 |
et al.
| 30. | 152-0001 | 2 | CAP, O.1MF 100V - F | c13, 14, | -50 |
et al.
| 31. | 152-0037 | 2 | CAP, 0.68 MF 100V - F | c10, Ti, | 20 |
et al.
| 32. | 313-0037 | 1 | Ic, TLOS} | U1, 3, | 70 |
et al.
| 33. | 313-0046 | 2 | IC, CA3080E | U6-11, 15, 16 1.80 | |
| 34. | 315-0007 | 1 | Ic, C4011A | U17-19, 22 | +60 |
| 35. | 482-0006 | 2 | XSTR, 2N4403 | Q2-11 | 50 |
ASSY G-80 POWER SUPPLY CHASSIS
| 36. | 482-0104 | 2 | XSTR, PWR T1P141 | T1P141 | 4.12 |
| 37. | 482-0100 | 2 | XSTR. PWR T1P125 | T1P125 | 1.20 |
| 38. | 482-0019 | 2 | XSTR, PWR T1P120 | T1P120 | 2.00 |
ASSY G-80 POWER SUPPLY PC BOARD
| 39. | 150-0088 | 2 | CAP, YOMF 25V - E | C5, 8, et al. -40 | |
| 40. | 150-0097 | 1 | CAP, 4700MF 16V - E | ee 16, 27, 2.20 | |
| 41. | 151-0011 | 1 | CAP, 0.01MF 50V - C | ae 22, 25, | -50 |
| 42. | 481-0002 | 1 | DIODE, MR751 | DIO, 12. | 1.60 |
| 43. | 481-0004 | 3 | DIODE, MR501 | D6-9, 11, | 1.00 |
13-17
ITEM_NOQ.
44,
45.
46.
47. PART NO.
481-0006
514-0002 514-0006
514-0008 gry.
www DESCRIPTION
DIODE, 1N914
FUSE, 3A FUSE, 1.5A
FUSE, 10A Slow Blow REF. DES.
Dl, 4, 5 PRICE
1.00
+26
SERVICE NOTE
SEGA / Gremlin’ EFFECT: “**™* 001 8/9/82 NUMBER:
An error has been Identified In the ZekTOR™ gwner's manual (P/N 420-0743), page number 45. Please make this simple correction to your documentation:
ITEM NO. PART NO. QTY. REQO. DESCRIPTION 3 800-0390 1 Assy Rotary Control
ey SEGA/Gremlin 8401 Aero Driva, San Diego, California 92123 @ Telephone 800-854-4098 /9 3®