CATHODE RAY TOMES

Fire Truck TM-115 1st Printing

Fire Truck (Atari, 1978) · Technical Manual · 125 pages · 100 sections · original scan

Page 1

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 2

GAME SERIAL NUMBER LOCATION

Your game's serial number is stamped on the circuit (back) side, bottom right corner, of the printed circuit board—see the illustration below. The same number is also stamped on the TV monitor chassis and on the label located on the rear of the game cabinet. Please mention this number whenever cailing your distributor for service.

Page 3

FIRE TRUCK

Operation, Maintenance

and Service Manual Complete with Illustrated Parts Catalog

A.

ATARI

Dover conmmesnors Comsary

Page 4

Copyright © 1978 by Atari, Inc. Al! rights reserved

Motorola and TEC service manuals reprinted by permission of Motorola Data Products and TEC Videoelectronics, Inc. No part of this publication may be reproduced by any mechanical, photographic, or electronic process, orin the form of aphonographic recording,

nor may it be stored in a retrieval system, transmitted, or otherwise copied

for public or private use, without permission from the publisher.

For permission request, write:

ATARI INC 1265 Borregas Avenue P.O.Box 9027 Sunnyvale, California 94086

6G Lithographed in the U.S.A.

ii FIRETRUCK™

Page 5

TABLE OF CONTENTS

1 LOCATION SETU!

A. INTRODUCTION 1 B. CAME INSPECTION . 2 ©. LOCATION OF SERIAL NUMBER 2 D. INSTALLATION REQUIREMENTS, 2 Power Requirements and Line Voltage Selection 2 Temperature Range 2 Humidity Range 2 Location Space Requirements 2 Type of Power Cord 4 £. INTERLOCK AND POWER ON/OFF SWITCHES 4 F VOLUME CONTROL 6 G. SELF-TEST PROCEDURE 6 H. OPERATOR OPTIONS 6

2 GAME PLAY A. ATTRACT MODE . woes 13 B. READY-TO-PLAY MODE . a 14 C PLAYMODE bee 14

3 MAINTENANCE AND ADJUSTMENTS A. CLEANING lo ee |

  • COIN MECHANISM 18 Components on Coin Door 18 Access to Coin Mechanism : 18 Cleaning of Coin Paths vo 9 Lubrication beens Adjustment of Coin Switch Trip Wire : . 19 Mechanical Adjustments on Coin Mechanism .... 2 20 General Troubleshooting Hints . 20 ©. FUSE REPLACEMENT E 22 D. TV MONITOR ADJUSTMENTS co 2 £. TVMONITOR REMOVAL asses LAMP REPLACEMENT vee BB G. SWITCH (LED) AND BUTTON RFPLACEMENT 23

4 THEORY OF OPERATION

A. GENERAL INFORMATION . 27 B. POWER SUPPLY . 30 ©. CRYSTAL-CONTROLLED OSCILLATOR AND TV SYNC GENERATOR... 30 D. MICROCOMPUTER cone 30 E MICROPROCESSOR coe 30 F MICROPROCESSOR CLOCK : . 30 G. MICROPROCESSOR WATCHDOG. bees so 36 H. ALPHANUMERIC GENERATOR : 1. 7 1 PLAYFIELD GENERATOR i

Page 6

TABLE OF CONTENTS

CAB VIDEO GENERATOR TAit VIDEO CENERATOR STEERING CONTROL LOGIC HORN AND BELL GENERATOR MOTOR AND SIREN CENERATOR BANG AND SCREECH GENERATOR AUDIO OUTPUT. SINGLE AUDIO AMPLIFIER

ILLUSTRATED PARTS CATALOG QPOZET RA

TV MONITOR SERVICING INFORMATION

MOTOROLA Service Manual A. GENERAL INFORMATION BL SERVICE NOTES Circuit Tracing Component Removal CRT Replacement Adjustments Regulator Adjustment . Horizontal Hold/Oscillator Adjustment Vertical HeightLinearity Adjustment Focus Adjustment Monitor Servicing C. THEORY OF OPERATION Power Supply +73 Volt Supply Video Amplifiers and Output D. HORIZONTAL DEFLECTION CIRCUITS. Phase Detector Horizontal Oscillator Horizontal Pulse Shaper and Driver Horizontal Output Sync Circuits Vertical Osciliator and Output Spot Kill Blanking Amplifier

TEC Service Manual GENERAL SPECIFICATIONS => oF

SW St St 5t

Page 7

TABLE OF CONTENTS

Power Supply input 103 Power Consumption . 103 Picture Tube - 103 High Voltage cose. 108 Horizontal Retrace Time -.. 103 Resolution 2. 103 Scanning Frequency 103 Tone Burst Amplifier 2... 103 Environment so 103

LIST OF ILLUSTRATIONS

Figure 1-1 Location Space Requirements . 3 Figure 1-2 Location of Voltage- Changing Plugs on the Power Supply 4 Figure 1-3. Location of interlock and Power On/Off Switches . 5 Figure 14 Location of Volume Control and Self-Test Switch 6 Figure 7-5 Option DIP Switches on Game PCB coe 7 Figure 21 Attract Mode Se 14 Figure 2.2 Ready-to-Play-Mode : 14 Figure 2.3. Play Mode coe 14 Figure 34 Coin Door Assembly Loe 1B Figure 32 Hinging Open the Magnet Cate Assembly . 18 Figure 33. Removal of Coin Mechanism oe 19 Figure 34 Surfaces to Clean inside the Coin Mechanism Le 19 Figure 35 Removal of Plate Covering Rear of Coin Slot Le 19 Figure 36 — Close-Up View of Lubrication Point Loe . 20 Figure 3-7 Detail View of Cain Switch and Trip Wire . 20 Figure 38 Adjustments on Coin Mechanism . 21 Figure 39 Locations of Adjustments on TV Chassis Loe 22 Figure 310 TV Monitor and Fluorescent Lamp Removal . 24 Figure 317 Switch and Button Replacement we 25 Figure 41 Functional Block Diagram of Fire Truck Game . 28 Figure 42 Block Diagram of the Fire Truck PCB we 29 Figure 43 Fire Truck Harness Schematic Diagram (2 Sheets} Lo 33 Figure 44 — Fire Truck PCB Schematic (6 Sheets} wee 35

Page 8

LIST OF ILLUSTRATIONS

vi Figure 452 Figure 456 Figure 46 Figure 47

Figure 5-1 Figure 5.2 Figure 53 Figure 5-4 Figure 5-5 Figure 56 Figure 5-7 Figure $8 Figure 5-9 Figure 5-10 Figure 5-11 Figure 5-12 Figure 5-13 Figure 5-14

Figure 67 Figure 6-2 Figure 63 Figure 64 Figure 65 Figure 66 Figure 67 Figure 68 Figure 69 Figure 6-10 Figure 6-71 Figure 6-12 Figure 6-13 Figure 6-14 Figure 615 Figure 6-16 Figure 6-17 Figure 6-18 Figure 6-19 Figure 6-20 Figure 621 1Mhz Timing Chart (Norma! Operation). 750Khz Timing Chart (Self-test Only) Steering Printed Circuit Assembly Output Pulses Single Audio Amplitier

ILLUSTRATED PARTS CATALOG

Final Cabinet Assembly Final Seat Assembly TV Monitor Assembly Main Control! Panel Rear Panel Assembly Coin Door Assembly Type 8 Power Supply Type A Fluorescent Lamp Assembly RF Shield Board Assembly Steering Wheel Assembly Foot Pedal Assembly Start Button Assembly Single Audio Amplifier Assembly Fire Truck PCB Assembly

T¥ MONITOR SERVICING INFORMATION

Motorola Monitor Circuit Board in Service Position Motorola Monitor Block Diagram +73 Volt Supply Circuit Motorola Monitor Vertical Drive Waveform Motorola Monitor Video Amplifiers and Qutput Circuit Motorola Monitor Horizontal Deflection Circuit Motorola Monitor Horizontal Deflection Waveforms Motorola Monitor Horizontal Output Circuit Motorola Monitor Sync Circuit Motorola Monitor Vertical Oscillator Circuit Motorola Monitor Spot Killer Circuit Motorola Monitor Blanking Amplifier Circuit Motorola Monitor Chassis Rear View-- Component Location Motorola Monitor Circuit Board Detait-- Solder View Motorola Monitor Schematic Diagram Motorola Monitor Circuit Board Detai!-— Component Location TEC Monitor Chassis, Rear View TEC Monitor Chassis, Top View TEC Monitor Printed Circuit Board, Top View TEC Monitor Schematic Diagram TEC Monitor Wiring Diagram. . . 64

co

ot

ao

... 104 . 105 vit

Page 9

LIST OF TABLES

Table tt Table 1-2 Table 1-3 Table 43 Table 6-1 Table 62 Table 63 Self-Test Procedure Operator Options Points Required to Earn Extended Play Microprocessor Signal Descriptions . Motorola Monitor Flectrical Specifications Motorola Monitor Replacement Part Numbers TEC Monitor Replacement Part Numbers . 6 .. a

vii

Page 10

LOCATION SETUP

A, INTRODUCTION Atari has added a new dimension to the video game world with the first “cooperative” driving game for one or two players—tire Truck™ A seat assembly and an upright cabinet connected together make up the game, Each assembly contains a player control panel The front cab and the back trailer of the hook-and-ladder firetruck are steered individually, unless it is a one player game, in which case the computer controls one half of the truck (either the front or the back}

FIRE TRUCK™

Page 11

Ina two-player game, one person sits and drives the ¢ab via the cabinet steering wheel. The second player stands and drives the trailer via the back steering wheel (which is part of the seat assembly}. The object of the game is to accumulate a high score by steering the fire truck through the course without crashing, or crashing as little as possible. For a detailed description of game play see Chapter 2.

A 23-inch TV monitor is mounted in the top of the upright cabinet, with the moniter viewing screen tilted slightly back from a vertical position. Playeroperated controls are mounted directly below the TV moniter on the front of the upright cabinet, and on the back top of the seat assembly.

Two identical coin mechanisms are mounted on the lower front center of the seat assembly, below the player controls. Either of these two mechanisms can in itiate play. The cash box is located behind a locked access door below the coin mechanisms.

B. GAME INSPECTION Remove the contents from both shipping cartons After aligning the front and back cabinet assemblies, attach the harness connectors. Insert and tighten three hexhead bolts with three split-lock washers into the steel bracket. After this preliminary assembly, follow the procedures below to ensure that your game is in perfect condition.

  • Examine all external parts of the game cabinet for dents, chips, or broken parts.
  • After determining that the game has been received in good condition, untock and open the rear access door. Carefully inspect the interior and verify that:

© All plug-in connectors are firmly seated

© All integrated circuits in sockets on the game printed circuit board are firmly seated

© The fuses are all seated in their holders

@ = = No harness wires are disconnected.

© No loose foreign objects are present, especially metal objects that could cause electrical problems.

Be sure all major assemblies are checked. Check the game printed circuit board (PCB), the transformer, the two coin mechanisms, the speakers, the fluorescent

  • FIRE TRUCK™ light, and the player controls. Also, be sure the TV monitor is secure in its mounting.

¢. LOCATION OF SERIAL SUMBER The serial number for Fire Truck is located on a metallic label in the upper left-hand corner on the back of the game cabinet. This serial number also appears in the corner (common to both edge connectors} on the back of the PCB, inside the game cabinet. See the illustration on the inside front cover of this manual.

D. INSTALLATION REQUIREMENTS Power Requirements and Line Voltage Selection

Fire Truck is shipped for operation at 110 VAC, 60 Hz, Power consumption is approximately 150 watts However, if your local voltage is not 110 volts, follow this procedure. You must select one of four connectors at the power supply and plug it into the voltage selection socket. Figure 1-1 shows the four connectors with one of them piugged in. The plugs are identified by wire color as listed in this figure. Note that there are two basic operating voltages — 110 VAC, 60 Hz, and 220 VAC, 50 Hz, with provisions for low line voltage in each case. To insure proper operation, measure line voltage. if voltage is consistently below 100 V (for 110 VAC lines) or consistently below 210 V (for 220 VAC lines), use the low-voltage connections. Use the black plug for low 110 VAC lines and the green plug for low 220 VAC lines,

Temperature Range

Location and storage should not be below 0 degrees Celsius (32 degrees Fahrenheit}, and ao higher than 49 degrees Celsius (120 degrees Fahrenheit)

Humidity Range

Relative humidity for location or storage should be no more than 95%

Location Space Requirements

The game requires a minimum of:

@ 160 centimeters (63inches}of vertical clearance

@ 64 centimeters (25% inches) of width space

@ = 160 centimeters (63 inches) of depth space

See Figure 1.1 for details.

Page 12

Figure 1-1 Location Space Requirements

FIRETRUCK™ 3

Page 13

Type of Power Cord

Atari has added a steain relief power cord to Fire Truck. The advantage of this type of power cord is that. if pulled accidentally. the strain relief will hold the cord in place at the pedestal base. The plastic strain relief “cushions” the impact of the shock and prevents the cord from pulling the wires out of the harness connector. Check the power cord assembly periodically for damage

E. INTERLOCK AND POWER ON/OFF SWITCHES To minimize the hazard of electrical shock while you are working inside the game cabinet, two interlock switches have been installed at the rear door assembly and at the coin door. These switches semove all power from the game while the doors are open. To help you conserve energy. a power on/off switch has been installed on the game so that it can be turned off during closed periods. This switch is located at the rear of the upright cabinet toward the top, as shown in Figure 1.3.

Check for proper operation of the interlock switches by performing the following steps:

1 Uniock and open the rear door assembly and the coin door.

2 Plug the AC power cord into a 110-volt source. (If voltage is consistently less than 110 VAC, make sure that you use the black plug instead}

  • Set the power on/off switch to the on position.
  • Close both doors. Within approximately 30 seconds the TV monitor should display a picture.

LINE VOLTAGE-CHANGING VOLTAGE PLUG WIRE COLOR 95 VAC BLACK 110 VAC ORANGE {installed at factory) 210 VAC GREEN. 220 VAC RED

NOTE: Power supply in your game may not include fuses F3, F4, and F5.

B Amp. 125V. Fast-Blow

©

(2)

ON/OFF AND INTERLOCK SWITCH

eo O&

Jamp. 250 v. Slow - blow 2.5 Amp.125 V. Slow-blow

Figure 1-2 Location of Voltage-Changing Plugs on the Power Supply

4 FIRETRUCK™

Page 14

POWER ON/OFF SWITCH

INTERLOCK SWITCH

Figure 1-3 Location of Interlock and Power OniOfi Switches

FIRETRUCK™ §

Page 15

SELF-TEST SWITCH

VOLUME CONTROL

Figure 14 Location of Volume Control and Seli-Test Switch

  • Slowly open each door until the TV monitor picture disappears. The picture should disappear when the rear door is opened less than one inch from the top
  • [the results of Step 5 are satisfactory, the interlock switches are operating properly. If the picture does not disappear as described, check to see if the appropriate switch is broken from its mounting or stuck in the on position.
  • Close and lock both doors.

F. VOLUME CONTROL If volume is incorrect ior your location, open the coin door and adjust the volume control. See Figure 1-4 for location of the volume control.

G. SELF-TEST PROCEDURE Fire Truck will test itself and provide data to demonstrate that the game's circuitry and controls are working properly. This procedure uses the TV monitor and the speakers; no additional equipment is required SEE FIGURE 1-4 FOR LOCATION OF THE SEIF-TEST SWITCH. To start the procedure over from the begin: ning, turn the switch off, then on again. This will return the test to Step 1 and can be done at any time during the procedure. See Table 1-1 for further details and instruc-

6 FIRETRUCK™ tions on the self-test. We suggest that you run the selftest procedure each time the coin box is emptied.

H. OPERATOR OPTIONS Options of the Fire Truck game offer maximum player appeal for each game location. These options are listed in Table 1-2. They are preset for a certain game setup during production. To determine how the switches have heen set for your game, compare the TV monitor viewing screen during the attract mode with the information in Table 4-2

To change the toggle positions of the switch assembly and set the desired options, the printed circuit board (PCB) must be removed according to the following procedure.

NOTE Fire Truck is the first Atari game to include a new style of easy-access PCB. The radio frequency shield has been redesigned to use only three quarter-turn fasteners—as a direct result of field input.
  • Unplug the game. Unlock and open the rear door assembly
Page 16

8-TOGGLE DIP SWITCH 4-TOGGLE DIP SWITCH } 5 / ol ae

Figure 1-5 Option DIP Switches on Game PCB

FIRE TRUCK™

Page 17

FIRE TRUCK™ Table 1-1 Self-Test

TEST

INSTRUCTION

RESULTS IF TEST PASSES

RESULTS IF TEST FAILS

Unlock and open the coin

door. Locate the self-test

switch and turn to the “on” position The ROM and RAM test

will follow, There are four ROM s programmed into Fire Truck they all check satisfactorily, there is no visible change or indication on the TV screen Throughout the self-test, a set of stationary graphics appear in a rainbow pattern (dark to light) from the left side to the right

side of the screen If the RAM s (zero-page and screen) check satisfactorily, there is no visible change on

the TV screen, 1, 2, 3 andior 4 is displayed in the lower left corner of the TV screen. These numbers cor respond to the failing ROM or

ROMs. j J ROM 1—ERROR ROM 4—ERROR These examples represent two of the possible four ROM s which could be in error. If the zero-page RAM is bad, a0 is displayed in the lower left corner of the screen, A 5 is displayed if the screen RAM

is bad, jy Bad screen RAM Bad Zero-page RAM

Page 18

FIRE TRUCK™ The next phase of the self-

The next phase of the self test checks the LED

switches and both steering

wheels on each control

panel.

Individually press the six

LED switches. Turn each steering wheel to the right, then back to the left. Then reverse the

procedure Trip the right and left coin switch wires. An electronic “pop” sound occurs each time a switch is pressed, and again when the switch is released. The same pop sound occurs each time there is a change in (the) direction in which the wheel is being tumed. The pop sound occurs whenever a coin switch wire is tripped. No sound indicates a stuck or broken switch, or an open or

shorted harness.

Page 19
  • Locate the radio frequency (RF) shield assembly im- 5, mediately inside the cabinet on the right. See Figure

1.5. On one end of the box is a printed circuit board

{PCB) with an edge connector coming from the edge of the board. (The RF shield assembly is an 6 aluminum box with small holes.)

  • Turn the three quarterturn fasteners on the RF Shield assembly by turning the wing nuts 4 turn
  • Carefully pull out the PCB and the RF shield board a8 one unit. These would not normally need tobe 7. separated when making option switch changes. Set the switches for the desired options, as shown in Table 1-2

Reinstall the PCB following steps 1 through 4 in reverse order. Do not force or bend the printed circuit board. Before reinstalling, always inspect the PCB for damage. Close and lock the rear access door.

Plug in the game and verify options functions by playing it

Table 1-2 Operator Options

OPTION 8-TOGGLE DIP SWITCH ON GAME PCB —TOGGLE NG:

fn2s45678

EXTENDED PLAY*

No Extended PlayONON
Liberal (Easy to Earn)ONOFF
MediumOFFON
Conservative (Hard to Earn)NOFFOFF

GAME TIME °

60 SecondsuONON
90 Seconds7ONOFF
: 120 SecondsEOFFON
150 SecondsDOFFOFF

GAME LANGUAGE

EnglishONON
FrenchONOFF

Spanish OFF ON

GermanOFFOFF

OPTION 4 TOGGLE DIP SWITCH ON GAME PCB —TOGGLE NO.: q 2 3 4

N

GAME COST Oo

T

Free PlayONON
Two Plays Per CoinuONOFF
‘One Coin Per Play5OFFON

Two Coins Per Play ‘ OFF OFF

*See Table 1-3 for point scores required to earn extended play.

10 FIRE TRUCK™

Page 20

Table 13 Points Required to Earn Extended Play

Game Length Setting

6090120150
secondssecondssecondsseconds
Extended Playoot-

‘Option Setting: Extended play granted for scoring.

Liberal90 pts.140 pts.190 pts.240 pts,
Medium100160220270
Conservative120180240300

FIRETRUCK™ 11

Page 21

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 22

GAME PLAY

Fire Truck has three modes of operation:

@ Attract — power applied or at the end of a game @ Ready-to-Play — coins accepted @ Play — after one of the Start buttons is activated

A. ATTRACT MODE {See Figure 2-1) The attract mode begins when power is applied to the game and the power switch 1s turned on, {The power onloff switch is located at the back of the cabinet, as shown in Figure 1-2} This mode also occurs at the end of every game. When the proper amount of coins clear the coin acceptor, the attract mode ends.

FIRE TRUCK™

Page 23

TOP SCORE

Figure 2-1 Attract Mode

During the attract mode the Fire Iruck is shown in the middle of the screen with the roadway scenery and hazards passing by BONUS information and TOP

SCORE information appear (alternately) at the top of the

viewing screen. The previous game SCORE and driver rating message (SORRY. SO-SQ, GOOD or ACE), appear alternately at the bottom of the screen. The player controls and game sounds are inactive during this mode

B. READY-TO-PLAY MODE {See Figure 2-2) When the correct amount of coins clear the coin acceptor, the ready-to-pley mode is initiated There is 1} change on the TV monitor {com the attract mode. The Start buttons on the control panels flash on and off according to the amount of credit registered for the game. If there is sufficient credit for a one-player game

PROSE START

Figure 2-2 Ready-toPlay Mode

14 FIRETRUCK™ only, the Front and Back Player Start buttons flash. If there is sufficient credit for a two-player game (or more), all of the Start buttons flash.

It is during the ready-to-play mode that players have the opportunity to select the “Hard” or “Easy” track. If the track select button is Jit, the hard track will be displayed for the duration of one game. The button has to be reactivated (Jit) at the beginning of each game for the hard track to be displayed.

This mode also occurs at the end of game play if there are credits remaining.

PLAY MODE (See Figure 2-3) The play mode begins when one of the Start but: tons is pressed. If the Front Start button or the Back Player Start button is pressed, the words PRESS START appear on the top and the bottom of the TV screen for approximately five seconds. This allows time for a se cond player to enter the game, even though additional credit is needed to do so. All other words disappear from the screen. If either one of the Two Player Start buttons is pressed, game play begins immediately,

Ibn | ;

ve

Figure 23. Play Mode

See Section H in Chapter 7 for various operator options (game time. cost, extended play levels, etc.)

As a one-player game, players steer either the cab or the trailer; the computer controls the other half of the Fire Truck. As a two-player game, the seated player steers the cab; the standing player controls the trailer.

The object of the game is to crash as little as possible, thereby obtaining a high point score. The front

Page 24

player (in a one- or two-player game) operates the accelerator foot pedal. In a oneplayer game, when the back player controls are used, the acceleration is controlled by the computer.

Whenever any part of the Fire Truck comes in contact with the side of the road (sidewalk) or another obstacle. the TV monitor flashes, all motion freezes, a crash sound is heard over the speakers, and the word CRUNCH is displayed on the screen. Acceleration then gradually resumes, if controlled by the computer

Points are awarded in increments of ten. Fach time

ten points are carned (by passing certain invisible points

on the track}, the sound of three ringing bells is heard over the game speakers. Other game sounds include the: Engine sound Siren sound Screech noise Bell and Horn sound (both activated by buttons on the contrel panels) Extended Play tone Crash sound

When extended play is earned, the track goes into a white video display for the remainder of such bonus time. It is possible to influence the direction of one part of the Fite Truck by radically steering the other. For ex ample, if the trailer is steered extremely to one side or the other, the cab steering will be hampered and a “static” noise will be heard over the game speakers.

FIRETRUCK™ 15,

Page 25

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 26

Due to its solid-state electronic circuitry, this Atari tune should require very little maintenance and only oecasional adjustment. information given in this chapter and elsewhere in this manual is intended to cover most servicing situations that may be encountered at a geme site The procedures given are wn sufficient detail to be understood by a person with moderate technical background

NOTE

If reading through this manual does not lead to solving a specific mamntenance problem, you can get help trom the following two Atan Customer Service offices

AlaniNew Jersey Customer Service Office 46 Colomel Drive, Piscataway, NI 08854 Toles 37-9347 (Monday-f nday, 830-5 pm Eastem time}

Dial toll-free trom anywhere in the shaded area on map below (800) 631-5374.

From New Jersey and elsewhere in the L$ dial (201) 981-0490

Atan:California Customer Service Office 1344 Bordeaux Drive, Sunnyvale, CA 94086 Telex 17-1103, (Monday-Friday, 730-4 pm Pacific time)

From California, Alaska and Hawaii dial (408) 745-2900.

From the remaining 47 states, dial toll-free (800) 538-4611 ADJUSTMENTS

FIRE TRUCK™

Page 27

A. CLE NG The exteriors of game cabinets and Plexiglas panels may be cleaned with any non-abrasive household cleaner. If desired, special coin machine cleaners that leave no residue can be obtained from your distributor. Do not dry-wipe the acrylic plastic panels, because any dust can scratch the surface and result in fogging the plastic

B. COIN MECHANISM Components Ou Coin Door Figure 31 shows the back side of the coin door assembly where the game’s two coin mechanisms are mounted. Included is the lock out coil assembly; the lock-out wires are connected to this assembly but are hidden behind the coin mechanisms. Powering the game causes the lock-out wires to retract far enough to allow genuine coins to reach the coin box When AC power to the game has already been turned off, the lockout coil is deenergized, causing the lock-out wires to move out far enough to divert coins to the return chute.

Directly below each coin mechanism is a secondary coin chute and a coin switch with a trip wire exten-

‘SLAM SWITCH ASSEMBLY

LOCK-OUT COIL LAMP HOLDER ding out to the front edge of the chute. When the trip wire is positioned correctly, a coin passing down the secondary chute and into the coin box will momentarily push the trip wire down and cause the switch contacts to close.

Also shown in the photograph is a slam switch assembly. It has been included to discourage any players who might try te obtain free game plays by violently pounding on the coin door to momentarily close the contacts on a coin switch. The slam switch contacts connect to the microcomputer system, which will ignore coin switch signals whenever the slam switch contacts are closed

Access to Coin Mechanisms To remove jammed coins, and for maintenance cleaning, each magnet gate assembly can be hinged open without removing it from the door, as shown in Figure 3-2. Or. if necessary, each coin mechanism can be entirely removed from the door merely by pushing down on a release lever and simultaneously tilting the mechanism back, then lifting it up and out. This i shown in Figure 33

Plexiglas® is a registered trademark of Rohm & Haas Company

Figure 3-1 Coin Door Assembly

18 FIRETRUCK™ Figure 3-2. Hinging Open the Magnet Gate Assembly

Page 28

Figure 3:3 Removal of Coin Mechanism

Cleaning of Coin Paths

‘CAUTION The use of an abrasive {such as steel wool or @ wire brush) or a lubrication on a coin mechanism will result in a rapid buildup of residue

By talking to many operators, we have found that the best method of cleaning a coin mechanism is by using hot or boiling weter and a mild detergent. A toothbrush may be used for those stubborn buildups of residue. After cleaning, flush thoroughly with hot or boiling water, then blow out all water with compressed air.

Figure 3-4 shows the surfaces to clean inside the coin mechanism. These include the inside surtace of the

(CLEAN BOTH SURFACES WHERE COIN ENTERS THE MECHANISM, AS WELL AS THE MAGNET)

Figure 3-4 Surfaces to Clean Inside the Coin Mechanism mainplate, and the corresponding surface of the gate assembly. There may also be metal particles clinging to. the magnet itself. To remove these you can guide the point of a screwdriver or similar tool along the edge of the magnet

If coins are not traveling as far as the coin mechanisms, you will need to clean the channel beneath the coin slot. To gain access to this channel, use a i8-inch wrench and remove all three nuts that secure the cover plate (refer to Figure 3-5). Removing the plate will provide access to the entire channel.

Also clean the inside surfaces of the secondary coin chutes, but when doing this be careful not to damage or bend the trip wires on the coin switches

Figure 35 Removal of Plate Covering Rear of Coin Slot

Lubrication Do not apply lubrication to the coin mechanisms, The only points that may need lubrication (and only rarely) are the shafts of the scavenger buttons (coin rejection buttons) where they pass through the coin door. Apply only one drop of light machine oil, and be positive that no oil drops down onto a coin mechanism. Figure 36 shows this lubrication point.

Adjustment of Coin Switch Trip Wire In order for a coin switch to operate reliably when a coin travels down the secondary coin chute. the rest position of its trip wire should be as shown in Figure 37 Use extreme care when handling or touching these wires

FIRETRUCK™ 19

Page 29

MANUALLY HOLD DOWN REJECTION BUTTON AND APPLY ONE DROP HERE

LOCK- OUT WIRE

Figure 3-6 Close-Up View of Lubrication Point

In Figure 37 you will note that the coin switch trip wire is oriented into the “V" of the secondary coin chute. The wire should extend to only about 1:8” beyond the chute

A retaining clip holds the wire onto the switch actuating stud. If you should loose a retaining clip. all is not lost. Just crimp the switch actuating stud over the trip wire with a pair of pliers.

Mechanical Adjustinents on Coin Mechanism Coin mechanisms are adjusted prior to shipment from the factory and normally will retain these adjustments for many months. li, due to wear or other causes, it becomes necessary to make new adjustments, remove the coin mechanism from the coin door. Then take it to a clean well-lighted area where it can be placed in a vertical position on a level surface (such as a

bench top). Besides a screwdriver, you will need a set of

several coins, including both new and old, worn ones. Figure 3-8 shows an exploded view of the mechanism and gives procedures for adjusting the kicker, separator, and the magnet gate. These adjustments should only be done by someone who has experienced in servicing coin mechanisms and who understands their operation.

20 FIRETRUCK™ CORRECTLY ADJUSTED TRIP WIRE

Figure 3-7 Detail View of Coin Switch and Trip Wire

Gieueral Troubleshooting Hints The first action is to look for jammed coins. After these have been removed, examine the coin path for presence of foreign material or loose objects (such as

chewing gum, small metallic objects, paper wads, etc.). In

cases where game usage is heavy. it may be necessary to clean the entire coin path periodically, in order to pre vent build-up of contaminants that can hinder the movement of coins through the mechanisms. Also confirm that the trip wire on each coin switch is intact, and is properly adjusted. If troubles still persist. check the conditions and positions of the lock-out wires, and the mechanical adjustments on the coin mechanisms, before suspecting the electronics. If a coin mechanism

Page 30

\TEM IDENTIFICATIONS

1 Kicker and Separater Screws

Washers: Kicker Separator Gate Lever Spring Gate Pivot Pin Malnplote Assembly washer Ri; Gate Assembly Cradle Assembly

~~ D

43 Upper Gate Pivot Spring 44 Undersize Laver Assembly Magne! Gate Assembiy Magnet Gate Adjuster 17 Retaining Screws 18 Coverpiate Aasembly 19 Return Coverpiate 20 Caverpiate 21 Mounting Studs 22 Lower Gate Pivot Spring 23 Goin Release Lever Kicker and separator 4, Set the acceptor with the back of the unit facing you in the test position.

  • Loosen the kicker and separator screws (1) and move the kicker (3) and the separator (4) as far to the right as they will go. Lightly tighten the screws.
  • Insert several test coins (both old and new) and note that some are returned by striking the separator.
  • Loosen the separator screw and move the separator a slight amount to the ‘eft. Lightly retighten the screw.
  • Insert the test coins again and, if some are still returned, repeat Step 4 until all the coins are accepted
  • Loosen the kicker screw and move the kicker as far to the left as It will go. Lightly retighten the screw.
  • Insert the test coins and note that some are returned.
  • Loosen the kicker screw and move the kicker a slight amount to the right. Lightly retighten the screw.
  • Insert the test coins again and, if some are still returned, repeat Step 8 untll all the coins are accepted.
  • Be sure that both screws are tight after the adjustments have been made.

Magnet gate Set the acceptor with the front of the unit facing you in the test position. Turn the magnet gate adjusting screw (16) out or counterclockwise until none of the coins will fit through.

  • With a coin resting in the acceptor entrance, turn the adjuster in or clackwise until the coin barely passes through the magnet gate. 4, Test this adjustment using several other coins (both old and new) and, if any fall to pass through the magnet gate, repeat Step 2 until all the coins are accepted
  • Fix the magnet gate adjusting screw in this position with a drop of give.

Additional Cleaning

  • Remove the transfer cradle (12) and the undersize lever (14). 2} Use a pipe cleaner or similar effective cleaning tool ta clean the bushings and pivot pins.
  • Replace the transfer cradle and the undersize ievar.
  • To be certain the coin mechanism is completely free of any residue, place the mechanism in boiling water for several minutes. Carefully remove it and let it air-dry completely before reinstalling in the door.

Figure 38 Adjustments on Coin Mechanism FIRETRUCK™ 21

Page 31

rejects genuine coins, try to readjust it. If this is not successful, then replace it with a working mechanism.

Correct operation of the slam switch can be verified by putting the game into the test mode and performing the switch test (described in Table 1), Correct operation of the other switches and of the lock-out coil can also be checked by the switch test, or else merely by manually operating them and watching game responses as it changes from the attract mode to play mode, and then back to attract mode again.

c€. FUSE REPLACEMENT Fire Truck contains seven fuses, five on the power supply assembly in the lower part of the cabinet and two on the TV monitor assembly. All fuses are easily accessible through the rear access door. Replace fuses only with the same. type of fuse as follows

TEC TM-600/623 Monitors: 3AG 2amp and 05-amp quick-blow, 250 volts Motorola M5000/M7600 Monitors: 3AG 0.8-amp quick-blow, 250 volts

Power Supply. Fuses FI and F2—3AC 2.amp slow-blow, 250 volts Fuses F3 and F4—3AG 2.5-amp siow-blow, 125 volts Fuse F5—3AG 8-amp fast-blow, 125 volts D. TV MONITOR ADJUSTMENTS

CAUTION For best results be sure the game has been turned on for a while before making any TV monitor adjustments.
  • NOTE The TV monitor adjustments are accessible through the rear door panel of the game cabinet. These adjustments have to be done while the game is energized. Therefore, only persons familiar with safety measures and repair procedures on electrical equipment should perform them.

The TV monitor should be adjusted only when the picture is distorted or if the contrast or brightness seem out of adjustrnent.

The monitor's adjustments function like those of a conventional, home television set, except that the volume adjustment has no effect. Instead, the game produces its sound in circuits separate from the TV monitor. Figure $9 shows the location of the adjustments on both TY monitors used by Atari Your game contains a TV monitor manufactured to Atari specifications by either Motorola or TEC

When making adjustments, follow these general guidelines:

Cam Cer ow

YOUTACE SWITCH sear ga posse)

TEC MODEL TM- 600/623 home ese Focus

MOTOROLA ‘MODEL M5000/M7000

Figure 3-9 Locations of Adjustments on TV Chassis

22 FIRE TRUCK™

Page 32

BRITE (Brightness)-—Perform this adjustment before the

contrast. Adjust so that the white lines covering the

screen just barely disappear, when the brightness is tured up.

CONT (Contrast)- -Adjust so that the images are as bright as possible against the dark background without being biurred.

HORIZ HOLD (Horizontal Hold) or HORIZ OSC (Horizontal Oscillator}— Adjust if the picture is slightly off-center horizontally, if the images apbear warped, or if the picture is broken up into a series of diagonal lines. Adjust for a stable, centered picture.

VERT HOLD (Vertical Hold)—This needs adjustment only if the picture appears to be rolling up or down

the screen. Adjust for a stable, centered picture

E. TV MONITOR REMOVAL (See Figure 3-10)

Remove three screws (buttor-head socket cap #10-32) at the top edge of the cabinet and remove the Plexiglas® retainer. Slide the Plexiglas screen (with graphics} out of the cabinet and remove the cardboard bezel. At the back of the cabinet remove the rear door assembly (four wood screws, #8 x 1.50" Ig)

With the back of the game cabinet exposed, remove four carriage bolts (%-20 x 2.007 ty) which secure the monitor to the TV shelf assembly. Disconnect the TY monitor harness and slide the monitor out through the front of the cabinet.

F. LAMP REPLACEMENT

(See Figure 3-10)

Fire Truck contains an 18-inch fluorescent lamp inside the top of the game cabinet assembly. To replace the lamp, remove the Piexiglas® retainer and screen, as. described in Section £ (TV Monitor Removal), The fluorescent tube can now be pulled straight out of the cabinet and replaced. G. SWITCH (LED) AND BUTTON REPLACEMEST (See Figure 3-11) The player Start buttons and track select buttons on both control panels are LED {light-emitting diode) switches. The Horm and Bell buttons are actually start button assemblies.

Unplug the power cord before working inside the game cabinet.

To remove the switches and Hom button on the front control panet it is necessary first to remove the rear door assembly. Reach in through the back of the cabinet and remove two wing nuts securing the control panel assembly to the cabinet. It is possible at this point to partially remove the control panel. (The panel is hinged and can be moved outward in order to expose the underside.) The switches are now accessible for servicing.

Toreplace an LED switch:

@ Remove all wires from the suspected switch. @ = Turn the switch counterclockwise while holding the cone-shaped nut on the outside of the game cabinet. @ Install a new switch using the reverse procedure. @ Reconnect the harness wires.

To replace the Horn or Bell button: @ Remove all wires from the suspected switch @ Remove four screws that secure the plates surrounding the button to the control panel. @ Squeeze both sides of the switch and pull out. © Replace the switch using the reverse procedure

(switch part number 60-020)

The LED switches and bell button on the back or Seat control panel are accessible for servicing when the panel is removed. Unlock and open the coin door. Reach in through the coin door and remove the two wing nuts as shown in Figure 3-11. Remove the control panel and follow the same procedures as described for replacing the switches and button on the front control panel

FIRETRUCK™ 23

Page 33

TV MONITOR REMOVAL

Remove PI

Remove playtield Plexiglas® shield

Remove cardboard bezel

Unplug TV monitor chassis connector and

remove four carriage bolts on TV shelf

assembly

  • Remove TV monitor AS > FLUORESCENT LAMP REMOVAL,
  • Perform steps 1 and 2 then gently rotate fluores-

it slips out of socket. Remove

Figure 3-10 TV Monitor and Fluorescent Lamp Removal 24 FIRETRUCK™

Page 34

ee REMOVE WING NUTS (2)

Loan wan

REMOVE WING NUTS (2)

REMOVE SCREWS SQUEEZE, THEN PUSH THROUGH

START SWITCH

Figure 3-11 Switch and Button Replacement

FIRE TRUCK™ rs}

Page 35

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 36

OPERATION

A. GENERAL INFORMATION The PCB block diagram of Figure 4-1 illustrates the major circuit blocks and theic related controls either on the board or remote. The inputfoutput lines are also shown. Figure 4-2 is a general overview of the Fire Truck game.

The game has a solid-state, self-contained television monitor which produces a picture quite unlike that of your home television screen. For example, the broadcast signal artiving at your home television set is translated into a different video level as compared to the game video signal from the PCB. The sound is generated by logic located on the PCB.

FIRE TRUCK™

Page 37

INTERLOGK ‘suite

orremLocK ‘swircr ry sounce TRE seer _eSeUTION oy

FRONT paver seutct SSeeUTON |

ae PLAYER SELECT S0SHOUITON

Leo

som MECHANISM

seurtest ‘swetcn woRZONTAL DEFLECTION

w montion circuney

VERTICAL percecrton

[comeosire ce)

same prinreD ‘amcur BORRD smnace ‘UD10, anpPce vate

FIRE TRUCK™ Figure 41 Functional Block Diagram of Fire Truck Game

Page 38

woss200us0KoWN

eT

Figure 42 Block Diagram of the Fire Truck PCB

FIRE TRUCK™ 29

Page 39

The composite video signal from the PCB is comprised of only four video levels instead of the more or less continuous shades of grey seen on a home television screen. The background of the picture is black video and the game objects are grey andjor white video levels

On the game PCB schematic diagram of Figure 44, the symbol “P” (appearing at various inputs of integrated circuit devices) indicates a connection of +5 volts DC through a pull-up resistor.

For easy location reference, the board is divided into sections. These sections are identified by letters A through R (skipping letters G, |, ©, and Q because they

may be easily confused with numbers 6, 1, and 0 respec

tively) across the short side of the PCB. Sections are identified along the long side of the PCB by numbers 1 through 11. The letters and numbers create a grid, and all ICs are located on the PCB along the grid lines.

An LM323 regulator is mounted in a large black heat sink and next to it is a 4ohm, 10watt resistor These components produce a great deal of heat during normal operation. The temperature is not extreme, bul sensitive skin may burn to the touch

The harness schematic of Figure 43 illustrates how all the electrical and electronic assemblies electrically connect.

B. POWER SUPPLY (See Figure 4-4, Sheet 1 of 6) The PCB receives +10 volts unregulated from the type B power supply chassis. This raw +10 volts DC is then regulated by an LM323 three-terminal device to 2 stable +5 volts DC. The +5 volts DC is distributed throughout the board to power all of the Fire Truck PCB

logic. At the top of the PCB, most of the wide traces are

DC ground. On the back of the board the wide trace along the long end of the PCB is 5 volts DC

Cc. CRYSTAL-CONTROLLED OSCILLATOR AND TV SYNC GENERATOR (See Figure 4-4, Sheet 1 of 6) The crystal-controlled oscillator generates a 12-MHz clock frequency (specifically 12,096 MHz) that is used to produce all of the operating frequencies required of the game PCB

The oscitlator output (12 Mitz} is divided by the divide-by-two to develop two &MHz signals (designated

30 FIRETRUCK™ as 6 MHz and 6MHz). The horizontal sync counters N9 and N10 are driven at 6 MHz, which provide the horizontal synchronizing pulses 1H through 256H. The signals HBLANK and HSYNC are developed in flip-flop P9. HSYNC is the clock input for the vertical counters which provide the vertical synchronizing pulses 1V through 128V. VBLANK and VSYNC are developed by a special coded ROM (read-only memory) at R4.

The horizontal and vertical synchronization signals are used lo produce a TV monitor raster made up of 262 horizontal lines at a frequency of 15,750 (250H). Synchronized with line 240 is a vertical blanking pulse that occurs for the duration of 22 more horizontal scans, resulting in the total number of 262 lines per frame.

D. MICROCOMPUTER The microcomputer consists of read-only memory (ROM), random-access memory (RAM), and a microprocessor. Ihe microprocessor controls the microcomputer operations through a Tébit address bus which addresses the program ROMs, Address lines BAO through BA? are also multiplexed with data signals to address the playfield and alphanumerics RAM. An 6-bit bi-directional data bus provides a path for transferring data between the microprocessor and the various memories. A special watchdog circuit makes certain that the microcomputer functions properly.

Address lines (BAO-BA10) are buffered to eliminate signal loading. These buffered address lines address the program ROMs (/1, J2. U1, L2, M1 and M2 for the 01 version and C1, D1, F1, and H1 for the 02 version), The direct non-buifered address lines from the microprocessor are A11-A15,

E. MICROPROCESSOR (See Figure 4-4, Sheet 2 of 6) The 6800 microprocessor (C3} is a bi-directional bus-oriented 6-bit parallel chip with 16 bits of address to select 65K bytes of memory,

To better understand the microprocessor (MPU), refer to Table 4-1 for a complete description of the data, address and control lines to the MPU. Only those control lines used are discussed.

F. MICROPROCESSOR CLOCK (See Figure 4-4, Sheet 1 of 6) The microprocessor clocks (1, 62] in this system run at 1 Mhz during normat operation and at 750Khz during a self-test sequence. Either of the two frequen-

Page 40

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 41

aim RIGM.

44-705 EDGE CONNECTOR

Tosv eT GRD Sy on | oa els coal oe

@ FOR POWER SUPPLY SCHEMATIC,

SEE 00TI97-01

POWER SWATCH

le. Su CT GRD aio GNREG Frou ONRES

cow TNO, cow 2 NO, ‘STEER IA sTeck STEER 78 STEER 2B ‘START LAMP 2 START LAMPS. ‘START LAMP | “TRACK SEL LAMP

Gh NO.

€ Stam wo ft Test ee StarT 1 No. [ra fos Be wa Sine Brant 3 NG No. START 2

TRACK Sty MO.

CABING: s envy

SK /w BKIw

Nle £i&

zs =! :

#57J veal||i=wis2 [wie
Vines oottiv YLee_WHY[wy

; wien ! nl won| Tes [ion woke ceo To *

Te peleM'4_RCaos
‘Ave outfie7!an
eCcoee—fae

COW NTR [IST | wocicouT core fw feMeet | | + -

i ay wise GRD (ow com) Rovie GRD jwiek.

  • FIRE TRUCK™ Te. ewia. lex. aN/ex fon ron. foe [wion eviw F aa 3 4 xu) SERRE 8 68,8, Ya Sty ia“ Ste Sen 108 “20°R1 “2224 a]

To SEAT CABINET (sata) COIN 4 BEAT CONTROL FRONT SPKR

Page 42

Tax

vowaFLUORESCENT
ouT3 lwLIGHT

re oF ty o

woe hw 4 wewtes sce cul | aw) eo te a A tenctosvac! MontToR | aT in

OW47.~~

OUT ° bes oa

re

a

Prine + — —_ BK | 43 | To SEAT CABINET _ wial 2s |? ESS Byl os AUDIO &

ees

:

Fut eac3ec ga? 1% m2. aie te 5 ttc tw ——J

can STEERING

Figure 43. Fire Truck Harness Schemati 03285401

FIRETRUCK™ 33

Page 43

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 44

TRANER I Te STEERING 27 ac PLYR START To Wo gt woh

Figure 43 Fire Truck Harness Schematic Diagram 03285401

FIRE TRUCK™ 35

Page 45

Microprocessor Signal Descriptions

Description/Function

These eight lines are bi-directional data bus lines.

These sixteen lines are unilateral MPU address lines to supporting memory (i.e,, ROMs, RAMs)

This input is permanently connected to a 1K-ohm pull-

This input line, when low, resets the MPU from either a powerdown or on a QE output of the watchdog counter. During the reset sequence prior to RESET going high, the contents of the last two locations (FFFE, FFFF) in memory are loaded into the MPU program counter to point the start of a reset routine.

This input when low indicates an interrupt request to the MPU. After the MPU concludes its current sequence it will then proceed to the IRQ sequence

This input line while going low indicates a non-maskable interrupt sequence. After the MPU concludes its current sequence it will then proceed to the NMI sequence.

This input line when high enables the MPU tri-state bus drivers. It is driven by the 2 clock.

Two-phase, non-overlapping MPU clock outputs.

This line is permanently tied to ground Table 44

Number

Signal of

lines

DoD? 8

ADAIS 16

HALT 1 up resistor.

RESET 1

IRQ 1

NMI 1

DBE 1

1, 02 2

Ts 1

Rw 1 This output is the read and write signal line for the RAM. memory. It normally is in the read (R) or high state.

cies are enabled when the TEST signal changes logic state at pin 1 of Data Selector F7.

When the TEST signal is high, the trailing edge of the 2Mh7B signal generated by flip flop }8 (on sheet 1 of

6) is selected to clock the JK flip-flop D5. The game is in

the normal operation as illustrated in timing diagram Figure 45a

When the TEST signal goes low, the game is in the selitest mode which requires a 750Khz clock. This clock is generated by selecting the 211 input to F7; this input clocks the D5 flip-flop—dividing it down to 750Khz. as illustrated ig diagram Figure 4-5b.

36 FIRETRUCK™ A positive ©1 changes the microprocessor address and data lines. A positive @2 initiates the micro processor to address memory and input/output data onta the data bus.

G. MICROPROCESSOR WATCHDOG (See Figure 4-4, Sheet 2 of 6) Watchdog is an external monitoring system that resets the program execution back to its initial sequence. This is accomplished by a watchdog statement, incorporated in program memory, that results in a WAT- CHDOG RESET pulse at the output of the address decoder.

Page 46

The watchdog circuit is a 5-bit shift register. In nortal operation the circuit is pulsed once each TV picture frame by the VBLANK pulse. If five frames occur without a WATCHDOG RESET pulse, the counter resets the microprocessor. This prevents random electronic static from upsetting game operation. The power-on circuit or the hardware for reset presets the counter, which in turn initializes the microprocessor and starts the attract sequence.

Hq. ALPHANUMERIC GENERATOR (See Figure 4-4, Sheet 3 of 6) Alpha characters and numerics are stored in ROM R3. Each character is traced in a block 16 lines square. The RAMs are shared between the microprocessor and the horizontal (H) and vertical (V) syne pulses. Data selector devices N1 and P1 select the desired addressing mode. Hardware addressing is accomplished when the HRDWR fine is low and the 4H pulse is low. This produces the A/N SEL signal for devices N1 and P1. The hardware data (V and H sync pulses) address the RAMs when A/N SEL is High.

It the microprocessor tries to access the RAMs when the HRDWR signal is low, the STPCLK signal stops the microprocessor clock while the hardware signals display the ROM alphanumerics. These alphanumerics are displayed at the {eft and right of the TY screen:

A high HRDWR signal returns the RAM addressing to the buffered address lines (BAQ-BA7}, The RAM uses data lines (BD0-RD7) when the buffered address lines are addressing the N2 and P2 RAMs. This continues unti) the next hardware addressing sequence.

The output of the alphanumeric ROM R3 is con: verted from 4-bit paraltel type to a serial output and clocked out to the summing gates through shift register L3 as the AJN VIDEO signal

I, PLAYFIELD GENERATOR {See Figure 4-4, Sheet 3 of 6) The playfield generator is similar in operation to the alphanumeric generator, The ROM (F5) is either addressed by the RAMs (J4, H4} or the microprocessor. The RAMs are addressed by either the position counters (€3,£4) or by the buffered address line (BAO-BA7)

When the PRAM signal goes low at the data selectors H3 and )3, it selects the playfield horizontal and vertical position signals (PHP,PVP). The PHP and the PVP lines are generated by the buffered data outputs of the microprocessor, When the PRAM line goes high the buffered address lines are selected, and the ROM is addressed. The address interchange is never interrupted, providing a contmuous playfield. The output of the playfield ROM F5 is converted from 8-bit parallel to serial output; it is clocked out to the summing gates through shift register E5 as the signal

CAB VIDEO GENERATOR (See Figure 4-4, Sheet 4 of 6) The cab video PROM (programmable read-only memory) P7 contains cab video display data. The cab is rotated by inverting the horizontal and vertical signals and then swapping them at the P8,N7 and R7 data selectors, The outputs CH and CV of the data selectors provide all 24 rotations of the cab. The PROM is addressed, and the cab video display data is outputted to device M7. The cab video signal is then ORed with the tail display data prior to the video summing yates.

K. TAIL VIDEO GENERATOR (See Figure 4-4, Sheet 4 of 6) The tail video ROMs J5 and £5 contain the tail video display data. This data is selected by the X and Y outputs from the sync rotation counters K3, L3, K4 and L4 at the ROM address inputs (AQ-A10). The tail video display is rotated by either the up or the down counting of the rotation sync counters that provide all 24 rotations to the tail. The Q outputs of M5 are then enabled, and the M6 eight-to-one data selector generates the signal to be ORed with the cab video display data prior lo the video summing gates

. STEERING CONTROL LOGIC (See Figure 4-4, Sheet 5 of 6) Steering (STFFR 1A, 1B, 2A, 2B) information for both the cab and the tail is “looked” for by the microprocessor (C3] during the play mode. The steering PCB assembly consists of two light-emitting diodes that are optically aligned with two light-sensitive transistors A toothed cylinder (tumed by the steering wheel) is inserted between the light-emitting diodes and the transistors, and it interrupts the light from the diodes

When the steering wheel is turned, two pulses appear at the output of the steering PCB assembly that differ in phase as illustrated in Figure 4-6. When the wheel is turned to the right, the A output pulse leads the B output pulse. When the wheel is turned to the left, the A output pulse lags the B output pulse. The inverse of the

FIRE TRUCK™ 37

Page 47

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 48

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 49

om e

Plas Taleo ay +su

Bho Von COCO ror [fo} FUSKT a Tom fk ROMS (3800-2 FF) ROME :3000-37F9) my ¢— Row czeo0- ares) ssn dns na BS ROWS (2000-2768)

aot

  • PRan sodoo-serF) TPRGE (0000-008F)

ce Sc -e0!

aette See exe ro) 04 ye rad etoRt : = apoe -_sdinyo*— Free 4 as— -

ES | ie eset 3

mE 230 67 , bilamer etc) aa mane seed

ba

ae

"

Sats Rie

#2

sey ww Foe ve va! ave 4 He. Be vee us2as = saa cog = 808 Sera en LL. 2 atte 4 mi son ti :

oy 7 a2 sp:

at—epe LG

40 FIRETRUCK™

Page 50

ep sb STEER RESET (980) 4p cABROT Coa, SRIORESET (1080) TRESARESET < 940) 2 4@L BSB (920) FPL ab C

"SygysyBYosu
|ewese

H of SQ PB stwoe Ls

fh,SBiesre—?=e+svnayosu

op?

Beare{..
w]eeDL = S0F ciscesJes [24is fagins 2
1814fe=
ye TaTEROT (140)ai:Eyzi

spent p32eie | oazars |oszaze | o22e23 ab - FSR (1490) Meio Gen acca

ab*— wPDe (ia 60)sot=
ap2. SresWO cwsorar
2 ee34a —27ins
ce |P2—- CRESHEND (1420)ia):
542 | _ MSTOREND (14.00)“—a
secon *sae4a- ise
1P3sas ——?-43

Y 4 i p——— b__warenpezatset : oc) 3 abe! 2 iad a ape] smmowsrs Coeo

‘ i he a To wT ye «ze BALEIR BEE oer 138 9 932820 337 J nt

a8 anv"

rey —t {93 —— Famed rs

-Ol VERS'ON

Figure 44 LAICROPROCESSOR

Fire Truck PCB Schematic Diagram Sheet 2 of 6 030926

FIRETRUCK™ 41

Page 51

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 52

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 53

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 54

eM

cw, ANSTO

BLA CRASHCODE

SKID CODE

Be 2 2fo* orLoviDES.

ems PEWNDD

caevioeo cAaéTan wucunpee —2]s De C84 neo ‘aut

  • SNe inca Spee »SeNG eee ~ 4 5 te |aepo* we gran — 3 | s 2 ereovineo 273% ahs : Lopsjiel 2 [Seay Ly eee feasa— Pe woo 2 a) Ne aia 9ee —— VBoANR —- Zora

2aasatonz <viDE0

Pevpvinz>

CAB TAIL

B14 Ale Gi sta 9s

= Peer

pe CRASICORE BK/DE 308

aa eNTR ay SKID ODE.

a

CAB TRI VIDEO OUT

Figure 44 Fire Truck PCB Schematic Diagram Sheet 4 of 6 030926

FURETRUCK™ 45

Page 55

ay

ROT (em

1KpeSTEER FLAGT

tv 802) ‘STEER ESET SUBER REA | STEER FLAG? 408)

leesraesrer [x] 2222

Sue: e Sue

_ 7.he

COIN 2,NO. [D sizes)

con smo. [a peeoe

MEER FLAG 2

ws spane [pp Ueoo?

neSv EER RESETams [op Bee
  • steer D RECTION | ——2Oe STEER cIRECTION 2 —<'#O2) eect fw Lees , <i Ey yss) wey, 11806), scrT,
we|SE UT
ae|‘TeEt 000)
sg5csCat

sien ae [ey 2), * ofS —sreea tinecron 2

—or“8
cheeos Ly+89 —______
Efe_’

en e107 RIES BIOs

|leros |10% P10K S10K

wha Ibe ew! cane Tone

evens

a“.DPTIONS
=a2one

eae TIME wages Sam Sees: 1

pybo |eeg
Hoe7

189 pp

ras ao Sei Sen Sars | 4-ros| 1OK FIOK YOK C1OK 3 [oe 'sw | —upoe —3| |

Deracom move | Bhool4
‘scow mone 2 +231

FOB.

=aile

won Seeogmor a Y Veoh -

5!LL

3 fussy ae

46 FIRETRUCK™

Page 56

ssy

ra cry

be

pa. x0

Seu

ery rears

Led

ive Sic6. Ps eae ba DATA eo?

op} Tg cow coonren

osv 21 “ ta—fOp ~ Hef START LAMP

De Sak glOK f or at TH = 4 stant came 2 yD!

  • ——— BF - oe prance seceer Came 268 ca sa Joo = Ssrant vane a

atrract——8)So!2 __ sr RRer cov

sov

fT § vocsout con Bo oo NEON

2Ae

INPUTS, OUTPUTS, OPTIONS

Figure 44 Fire Truck PCB Schematic Diagram Sheet 5 of 6 030926

FIRE TRUCK™ 47

Page 57

Hom

Boe BeUTSoF —— wn es

  • a Ree RE oy B10 en esa jj} Bec ol

R72 om

IN 3505

+sy

MoToRy

MOTOR? MeToR? moToaa

einem sent SrA END, sieue zw

caash

cRASHE

cn asy?

Bana

caasm

CRASHES

CRASH

48 FIRE TRUCK™

Page 58

MOTOR

ATTRACT —

Z}Aavoio CN

Sen Etta ante cevamry

Se 238

AUDIO, AVOID OUT

Figure 44 Fire Truck PCB Schematic Diagram Sheet 6 of 6 030926

FIRETRUCK™ 49

Page 59

owe SLL. mize ! oe a

mz +S Lt Ly L_I LL eae J LJ ve o2 TOGGLES Figure 45a 1MHz Timing Chart (Normal Operation)

ow SLELEPLI LIL LI

2 TOGGLES

Figure 456 750 KHz Timing Chart (Self-Test Only)

STEERING A1 7 ee RIGHT TURN STEERING Bt __f Ld

STEERING A2 —_ FF L_J LEFT TURN STEERING B2 _ | Ld

__] Figure 46 Steering Printed Circuit Assembly Output Putses

50 FIRE TRUCK™

Page 60

two pulses are applied to the D and clock inputs of the D-type flip-flops.

The MPU recognizes that a steering manuever has been made when a low appears on data line BD7. The MPU then looks at the data line BDO and determines from the logic Jevel (high or low) whether the turn is left or right’ Once the MPU has processed a steering maneuver, the MPU then outputs an address that is decoded by the address decoder and results in a low STEERING RESET signal. This signal resets the D-type flip-flop responsible for the STEER FLAG signal

. HORN AND BELL GENERATOR (See Figure 4-4, Sheet 6 of 6) The horn is manually sounded by pressing a large pushbutton labeled HORN at the cab control panel

The bell is also manually sounded by pressing another large pushbutton labeled BELL at the tail (trailer) control panel. This also occurs automatically when points are scored. The bell is disabled by the microprocessor if the game is in the “front player only” mode {trailer is controlled by computer).

N. MOTOR AND SIREN GENERATOR (See Figure 4-4, Sheet 6 of 6) The key to the motor generator is the operation of transistor Q1 in conjunction with timer B9. Timer BY operates as an oscillator with its output frequency dependent upon the collector voltage of Ql. This voltage is the result of the base voltage selected at the MOTOR 1, 2, 3, or 4 input tines.

As the Q1 base voltage increases, so does the charging voltage at the collector across capacitor C25. This VCO control voltage sets the VCO circuit at a frequency selected by the buffered data lines; the voltage is adjustable by setting pot R27. The VCO output is divided into two separate frequencies by the divide-bytwelve device A9, and is then summed by resistors R73

and R74. This produces a realistic motor sound as the

player shifts gears.

The siren generator is similar to the motor generator. The control voltage to the VCO is generated by voltage levels present at resistors R45, R46, R47, RAB that drives voltage follower E9. The output of E9 is the control voltage that controls the output frequency of timer B9.

  • BANG AND SCREECH GENERATOR (See Figure 4-4, Sheet 6 of 6) The heart of the bang and screech generator is the naise generator comprised of 8-bit shift registers BB, C8. These two devices are connected in a manner to produce random noise at the QH (pin 13) output of B7.

The bang is the result of data (BD4-BD7) from the microcomputer; the data is used to gate varying amounts of random noise through to the audio amplifier. Starting with binary data code 1111, then rapidly stepping the data code down to 0000 results in gating noise from noise generator B8, C8 through a resistive value of 550 ohms (R34, R35, R36, R37 in parallel) to 8.2K ohms for a data code of 6001, and infinity for a data code of 0000. The result is an envelope from full “on” to full “off”.

The screech sound is produced by processing the output of the random noise generator with a type of hysterisis feedback loop, comprised of Schmidt-trigger inverter 84 (7414). This processed noise is gated to the audio summing network each time SKIDSND goes low and clears the Bé flip-flop.

P. AUDIO OUTPUT (See Figure 4-4, Sheet 6 of 6) All the processed sounds (i.e. siren, motor, horn) are summed at the inverting input of op-amp E9. The output of E9 is then amplified by the single audio circuit. This circuit is not located on the Fire Truck PCB.

Q. SINGLE AUDIO AMPLIFIER

(See Figure 4-7) The single audio amplifier for Fire Truck is the -01 version assembly which uses only one of the audio amplifier circuits. The audio output (pin 18 of the Fire Truck PCB) from op-amp E9 is amplified and matched to an @-ohm speaker. The audio level (volume) is adjustable by rotating the R2 potentiometer located on the Single Audio Amplifier PCB

FIRETRUCK™ 57

Page 61

INPDT £

OuTeuT 1

eRe ERB CRS CRIO CRN CRIZ 26 vac |S ot — tit > + A MR7SO INZOOI x S PL as

2200nF CRI

ZEvAG [lo - MRISO

GND [4/719 -— =

ow! TEST TEST [e-—.

Figure 47 Single Audio Amplifier PCB A00957401 BB

52 FIRE TRUCK™

Page 62

ILLUSTRATED PARTS CATALOG

The purpose of this chapter is to provide you with the necessary information for ordering replacement parts for the Fire Truck game.

When ordering parts from your distributor, give the part number, part name, applicable figure number of this catalog, and the serial number of your Fire Truck game. This will help to avoid confusion and mistakes in your order. We hope the results will be less downtime and more profit from your game.

Page 63

Com rn

Figure 5-1 Final Cabinet Assembly A A032758-01

54 FIRETRUCK™

Page 64

Figure 5-1 Final Cabinet Assembly Parts List

ATARI a = Item Part Number 4 Qty. Description

1032756-021 | Assy., Cabinet Wood #/Graphics
2A032747-011 | Assy., T.v. Monitor
3AQ32757-O11 | Assy., Main Control Panel
4A006917~05118" Inch Pluorescent Light Assy
5A009569-011 | Final Assy., Foot Pedal
6007197-021 | Power Supply Assy Type B
7A030867-011 | Assy, R.F. Shield Enclosure
84030928-011 | R.F. Shield PCB Assy
9A030927-011 | Main PCB Assy
10A033016-011 | Strain Relief Power Cord Assy
ayA032855-021 | Main Harness & Switch Assy
12032854-01Ref | Harness Schematic
1346- 2012022 | Fuse, 3 AG Slow Acting 2 AMP
14030952~011 | Plex Retainer
4s030955-01qPlex Screen W/Graphics
16032755-011Bezel W/Graphics
17002728-012BRK., Panel MTG.
18000869-011 | Speaker Grill
1948-0041Speaker 5" (Arkay)
20AQ32741~011Assy Door Rear W/Lock
au007103-011 | On/Off Switch Cover
2275-070484Torque Washer
23TM-1151Tech Manual
24ST-1151 | Self Test Chart
25005233-011Rear Door Seal
26032760-011Patent Drawing
2775-990900063 | Well Nut, Blind Hole Fastener
2882-B8016B3 | Screw, But. Hd., Socket #10-32 x 1.00 BIK.
2975-070213 | Washer, Flat, Black Nylon, #10
3075-015814 | Washer, Flat
3275-04516 | Washer, Split~Lock 4
3275-9352 | Wing Nut 4-20
3375-915812 | Nut, Hex 4-20
3475-5532N4 | Bolt, Carriage 4-20 x 2.00" Lg.
3575-5516N4 | Bolt, Carriage 4-1.00" Lg.
3672-55322Screw Hex Ha. 4-20 x 2.00" Lg.
3773-770044 | Rivets 3/16 x .68" Lg.
3872-681212 | Screw, S.M. Self Tapping #8 x .75" Lg.
3982-18244 | Screw, Wood #8 x 1.50" La.
4072-66108Screw, S.M. Pan Ha. Phil. #6 x 5/8" Lg.

iw] A Warner Communications Company

FIRETRUCK™ 55

Page 65

—— NY Ma Ve [~ .

= '

ecwal ger ’

yrs aone®@) a

A Figure 5-2 Final Seat Assembly A032716-01

56 FIRE TRUCK™

Page 66

A Figure 5-2 Final Seat Assembly Parts List ATARI

ItemPart NumberQty.Deseription
1AQ32715-022 | Assy., Cabinet ~ Seat W/Graphics
28032719-01i}Assy., Rear Control Panel
3A009083-O11 | Assy., Final Coin Door
4A009548-011 | Assy., Coin Box Lid
$009549-011 | Coin Box
6030717-011 | Bracket (Coin Box)
7002728-012 | Bracket, Panel MTG
848-0042 | Speaker 5" (Arkay)
9000869-011 | Speaker Grill
1073-70044 | Rivets 3/16 x .68" Lg
lL75-5516B4 | Bolt, Carriage 4-20 x 1.00" ig Blk
1275-015813 | Washer, Plat 4"
1375-990505S4 | Nut, Lock Shallow Pat. Nylon 420
14032721-011 | Connector
4875-5520B9 | Bolt, Carriage 4"-20 x 1.25 Lq Blk
1675-9359Nut, Wing 4-20
775-0459 | Washer, Split-Lock 4"
1s72-681210 | Screw, SM Sclf-Tapping #8 x 3/4" Lg
19A032857-011 | Assy., Seat Harness & Interlock Switch
20A009574~011 | Assy., Single Audio Amp Bd.
aL72-66109 | Screw, SM, Pan Hd Phil. #6 x 5/8" Lg.
22032763-011 | Silkscreen, Plex-Coin Door
23032763-021‘" ="
24032763-031SS
25032763-04L"=i

FIRETRUCK™ 57

Page 67

4-RE00 BREQO gs

Figure 5-3 TV Monitor Assembly A032716-01 A

58 FIRETRUCK™ ba

Page 68

A ATARI Figure 5-3 TV Monitor Assembly Parts List

Item Part Number | Qty. Description

i:A032746-011Assy., T.V. Tray
z90-0321Monitor 23"
3005594-014Brk't., Monitor Tie Down
472-68128Screw, Sm., Pan Hd., Phil, #8 % .75 Lg.
575-51202Bolt, Carriage #10-24 X 1.25 Lq.
675-0402Washer, Split-Lock, #10
775-9110azNut, Hex #10-24
875-038C2Washer, Plat 4"
9006 313-021Copyright Decal 1978

@& 4 warner Communications Company

FIRETRUCK™ 59

Page 69

WV OL

MIA Nada

A Figure 5-4 Main Control Panel A032747-401

60 FIRETRUCK™

Page 70

Figure 54 Main Control Panel Parts List

F a

ItemPart NumberQty.Description
1030959-011 | Main Cont., Pnc., W/Graphics
2032699-011 | Control Panel Wood

3 | Aoo0S98~-03 1 | Steering Wheel Ass'y.

4000S67-011 | Bow Washer
5A007357-011Start Button Ass'y.
6001856-023Bushing, Alum.
762-0023Led Switch
8 | A032856-011Control Harness
975-5520B2 | Carriage Bolt, 4-20 X 1.25" Lg. Blk.
1075-015s2Washer, Flat &
i75-04520B2Washer, Split-Lock 4
1275-91582Nut, Hex, 4-20
1385-22F1126 | Screw, Mach., Pan Hd., Phil. #10-24 X 3/4 Lg., Type F
1472-66102Screw, Sm., Pan Hd., Phil. #6 X 5/8" Lg.

© 6 vere: Communications Company

FIRE TRUCK™

Page 71

62 FIRETRUCK™ Figure 5-5 Rear Panel Assembly A032719-01 A ERENT VIEW n~!

  • BK (Noy Rit} EN
Page 72

A ATARI Figure 5-5 Rear Panel Assembly Parts List

pa = =~ 22 ee = -

ItemPart NumberQty.Description
1030960-01LRear Cont., Pne., W/Graphics
2032699-011 | Control Panel Wood
3 | Aooos98-031Steering Wheel Ass’y.
4000567-011 | Bow Washer
54007357-O1LStart Button Ass'y.
6001856-023Bushing, Alum.
762-0023Led Switch
8 | A032856-011Control Harness
bi75-5520B2Carriage Bolt 4-20 X 1,25" Lg. Blk.
1075-01582Washer, Flat %
iL75~04520B2Washer, Split-Lock
4275-91582Nut, Hex, 4-20
1385-22F1128Serew, Mach., Pan lid., Phil. #10-24 % 3/4 Lg. Type F
472-66102Screw, Sm., Pan Hd., Phil. #6 X% 5/8" La.

——I

FIRETRUCK™ 63

Page 73

(is) 6 PLCS

@ an Be 2 PLCS Qi)

  • 2 PLCS
  • 2 PLCS
  • 2 PLCS 2 PLCS @)

@)

  • 2 PLCS

YEL YELIBK' f @)4 PLCS BKIYEL (4) @ @

Figure 5-6 Coin Door Assembly A009083-01 c

64 FIRETRUCK™

Page 74

Figure 56 Coin Door Assembly Parts List

ATARI

ItemPart NumberDescription
1AN07637-011Front. Bezel-only on -01 Coin Door
A0076 37-02ReE.| Front Bezel-only on -02 Coin Door
3007637-03Ref. Front Bezel- Used only on -03 Coin Door:
0076 37-04Ref.) Pront Bezel- Used only on -04 Coin Door Assy.
AO007637-05Ret.| Front Bezel- Used only on -05 Coin Door Assy.
A007637-06Ref.| broat bezel= Used only on -06 Coin Door Assy.
ADO 1637-0Ref.| pront Boze)- Used only on -87 Coin Door Assy.
va75-91654Nut 6 37
3A030362-011Coin Lock-Out Assembly
44007640-012Coin Switch Aably
5A002465-01idCoin Counter A: tas Ly
6004 320-013Coin Door Weldment
7004341-012Secandary Coin ©
004344-011Key Loop
9004340-01ZzSpraug~wen
16004337-012Bracket, Wire Form
Ml004338-011Jock-Out, Wire Form, KW.
12G04336-O11Lock-Out, Rire Fern, 1H
13004 326-012Button, Scowerger
475-0464inckher, 86
15006904-012Spacer,
le007359-011hemp Socket
1?70-11-47pfu
1873-30082Retaining "CT Rfruare #elUee 2's
1375~-9914001oSelf€-Threading Net. Tismertia FSRIBEOUG
2075-026S4Washer #t
2175-0051613Kepnut, Style 84Stl., @-%32
22008629-012Spring
2374-21181
24TI-b225cu2
FL-L25EBRef.5 Francs Oniy
71-1205FFRef.for Geran Mark only
71-1201MGRef.) coin Mecharfor Swedish Krona Only

71-1201KS Ref.] Coin Mechanism for Japanese LOO Yen Only

F1-12WPERef.for English 10 Pence Only
F1-1L220¢ARef.for Australian 20-Cent Piece only
25007753-01LPlate, Auti-Probe
2640076 38-011Switch Assembly —
L 27A006921-011Harness Assembly

© 4 verre: Commumeanons Company

FIRETRUCK™ 65

Page 75

& Figure 5-7 Type B Power Supply A007197-01 c

66 FIRETRUCK™ gs REQC

Page 76

Figure 5-7 Type B Power Supply Parts List

Item Part Number

1 009266-01 A006886-01 3 29-053 4 78-70501SC 5 A006555-01

7 79-4411004 8 41-2003 9 A006958-C1 10 A006958-02 1 A006958-03 12 A006958-04 13 78-2708 14 72-1810S

16 75-048 vv 75-9188 18 75-0188 19 4007192-01 20 A007444-01

21 46-203801 22 46-201251 Description

Power Supply Base Weldment Assembly Transformer Termination Assembly “Type B” Cap., Sprague Electrolytic 26,000uf @ 15V Brkt., Cap. Mtg. Sprague #4586-48 P.C. Board Rectifier

Fuse Holder, Panel Mounting Filter, Power Line, 5 AMP Volt Sel Block 95V Volt Sel Block 110V Volt Sel Block 205V Volt Sel Block 220V Grommet ,Plastic Screw Pan Hd., 48-32 x 5/8"Lg.

Washer, Split-Lock #8 Nut Hex #8 Washer Flat #8 Power Switch Termination Power In Harness Fuse, 8 AMP, 125V, 3 AG Fast Acting Fuse, 2% AMP, 125V, Slow Acting

A warcer Communications Comoany

FIRE TRUCK™

Page 77

TT LIGHT | HARNESS | SEE size LENGHTH | NOTE ee "BIN, DON. : ae con [ew Ion

2 REQD

oy inm@——— -©7 9 -10 oncy Ox

Figure 5-8 Type A Fluorescent Light Assembly D A006917-01

68 FIRETRUCK™

Page 78

A

ATARI’

Figure $8 Type A Fluorescent Light Assembly Parts List

=4

ItemPart NumberQuy.Description
L93-1041Gibson Fluorescent Fixture 18 inch
270-3031Fluorescent Tube 18 inch (or Equivalent)
3AQ06916-O11Fluorescent Light Harness, 100"
478-26521 | Grommet, Rubber
578-24001a/R | Tie wrap
679-5618162 | Wire Nut, Ideal 71-B

FIRETRUCK™ 69

Page 79

SEE

WOTE ONE

SEE NOTE ONE,

0019 OOO 000 hee

lool veer 8

SEE NOTE ONE

il roy 8) ot ih C DEF HOKUMNPERSTUY WEY

ry ° Ol

° a 2Pu ROW |

SPL

RF Shield Board Assembly A030928-01

70 FIRE TRUCK™ BS Q Q

Re

34a

oa

FASTENER

3PL

MASK THESE SEVEAN(7) HOLES PLUS AIR HOLES BEFORE FLOW SOLDER

fe subject matter af the Grawing or any design ar technical information shown thereon, nor any right to "apr thereo!, except for marulacture by vendors of A porated and for manulacture under the corpor fen license, no right to reproduce this drawing Is granted fof the subject matter thereo! uniess by writtan agreement with or writien permission from the corporation. '

'

t

Page 80

A Figure 5-9 RF Shield Board Assembly Parts List

ATARI

re ot

ItemPart NumberQty.Description
1030835-011P.C, Board
22D-101624Cap., Monolythic, 0.luf, 50V
341-300312Inductor, 100uH
452-00313Jumper, .600 Centers
575-E61060823Wing Screw, #6-32 x 1/2" LG
675-9525013Fastener, 1/4 Turn, #6-32, Stainless Steel
779-5172221Connector, 44 Pin P.C. Mount
8030868-012Mount, Connector

—+___. ———____-_-___—__

© A warner Communications Company

FIRE TRUCK™

Page 81

Figure 5-10 Steering Wheel Assembly A000598-03 R

72 FIRE TRUCK™

Page 82

Figure 5-10 Steering Wheel Assembly Parts List

ATARI

= — = = fTtem Part Number Qty Description 1 r A000598-03 Ref | Steering Wheel Assembly

2000599-021Cover, Atari Logo
30006051 | Housing
40006061 | shaft
5&5-22F 2062jScr. Sht. Metal, #2-56 X 3/8 'F' Type
672-75123Mach Scr, #4-20 x 3/4 Lg, Fillister Hd Slotted
70006071Printed Circuit Assy
875-0700 22 | Washer, Fender, &
976-0920201Bearing, Thompson (20L20-FX)
1076~-0910101Bearing, Thompson (10L10-FX)
lL78-401041Steering Wheel, 10"
1275-990505 S| 1 | Nut, 4-20, Nylon tock, Shallow Pattern
1372-9580‘1[Mach Ser, 4-20 x 5 Lg, Truss Hd, Slotted
14000616110 | Hub Light
is75-0551 | Washer, &" Int, Tooth, Starlock
1675-0422|Washer, Split Lock #2

FIRETRUCK™ 73

Page 83

74 FIRE TRUCK™ Figure 5-11 Foot Pedal Assembly 400956901 C IEW AT ARROWS 18,

Page 84

A. ATARI Figure 5-11 Foot Pedal Assembly Parts List

L

TtemPart NumberQty.Description
L009565-011 | Mounting Plate
3A008857-011 | Assy foot Pedal
465-071C1 | Switch, Micro
5002191-011 | Brkt, Foot Pedal Switch
6009564-011 | Mounting Boara
7000592-011 | spring
875-035C1 | Washer, Steel k (Wide Pattern)
9003546-011 | Washer, Rubber % ID x Ik" OD x 1/8" Thk
1072-1508C1 | Screw, Mach Pan Hd Phil 4-20 x 4 Ly.
175-915C2. | Nut Hex, 4"-20
1275-035C2 | washer Flat %"
4375-0452 | Washer Split-Lock 4"
1472-141 282 | Screw, Mach., #4-40 % 3/4" Lq.
as4.030003-011 | Assy Foot Pedal Harness
in75-91882 | Nut, Hex, #8-32
a775-0482 | Washer, Split-Lock, #8
1875-9145aNut, Hex, #4-40
1975-0442 | Washer, Split-Lock, #4

[w) A Warner Communications Company

FIRE TRUCK™ 75

Page 85

=

CLR AS REQUIRED

HPL

Figure 5-12 Start Button Assembly 40073571 D

76 FIRE TRUCK™

CONTROL PANEL REF

Page 86

A. ATARI Figure 542 Start Button Assembly Parts List

ItemPart NumberQty.Description
L006530 -011Bezel
2006535 -011Button
3006532 =011Chassis
4A006533-O11Switch Mtg. Plate Assembly
579-43172Lamp Socket
670-11-472Lamp
7$2-020lSwitch, Cherry, E68-SOA
872-16036Mach Screw, 6-32 x 3/16 La, Pan Hd, Phil.
982-88084Screw, Button hd socket 8-32x 4 Ig. Black
1075-91884Nut, 3-32
W75-0484Washer, #8, Split-Lock
12004577-192Jumper Wire, Black
1375-0466Washer, Split-Lock #6

FIRETRUCK™ 77

Page 87

TRACES ARE ON

OPPOSITE SIDE

Figure 5-13. Single Audio Amplifier Assembly 400957401

78 FIRETRUCK™

Page 88

A Figure 5-13 Single Audio Amplifier Assembly Parts List

ATARI

ItemPart NumberQty.Description1
Ll009575-01LP.C. Board
210~51P01Res, Carbon, 5%, kW, 1 OHMR3,10
310-5390i*“8 39 «CSR6,9
411-52P7L.7“dW 2.7"R4,7
511-51211"""120 "R5,8
619-3161031Trimpot,10KR1,2
724-2501061cap, Electrolytic, 25V, loufcl2, 13
824-2504771**"" 470ut€2,7
924-2501081"a“ 1000ufC1,6
10 24-250228a"ial” 2200ufc5,C10
1 27-250103Po.7 Ceramic,25sv. .OlufC3,8
12 27-2501042""" -lufC4,9,11,14
13 31-MR7501Diode MR75CCRL,2
14 31-IN40015Diode IN4001CR3-12
15 37-TDA2002V1Audio AMP, TDA2002VUL,2
16 69-0041Switch, SlideSwi
17 78-58005LConnector, 10-Position
18 030184-011Heatsink
ig 72-1604C2Screw, P.H., Phil, #6-32 x % Lg Cres
20 75-0562Washer, Lock, Int Star #6
21 | 78-16009LSilpad
22 | 10-5104iRes, Carbon, 5%, %W, 100K OHMR1L,Ri2

FIRETRUCK™ 79

Page 89

-Ol versal

Fine yaveK Aososze

Figure 5-14 Fire Truck P.C.B. A A030926-01

80 FIRETRUCK™

Page 90

A. Figure 5-14 Fire Truck PCB Parts List —01 Version

ATARI a ee] Item Part Number i Qty. Description r 1 030927-01 1 P.C. BOARD 2 10-5101 4& RES., CAR. COMP, 5%, kW 100 OHM 888-91 3 10-5271 3 " " bi mt w 270" R8,9,41 4 10-5331 2 " 7 - y ow 330 " R16,31 5 10-547) 2 " " sia q " 470 " R32, 33 6 10-5681 1 " i " " 680 ROG 7 10-5821 1 " id u oo 820 " R51 8 | 10-5102 7 " Hom ow om 1K 4 R1,2,4,15,18-20,30, 34,39 ,57,61,67, 68, 76,108,109 9 10-5182 2 “ u w Li “4.8K " R38 ,40 10 10-5222 3 2 a. Ld a "2.2K" R29, 36,60 11 10~5392 1 " " ” " "3.9K" R35 12 10-5472 1 " " " moot 4.7K RSG 13 10-5822 1 tt " . "8.2K " R37 14 10+5103 4? " " u “ 10K " R3-7,10-13,17,26,56, 59 62 65,69, 73-75, 77-87 92-107, 110 15 10-5153 1 " " 2 wom USK RSD 16 10-5223 2 " " s wom 28K R43, 55 Vv? 10-5273 1 " " " woo 27K" RSB 18 10-5333 2 / " iis tom 33K R53, 66 19 10-5473 4 " “ wo BK RGD, 70-72 20 10~5683 1 " " " woo 68K "R25 21 10-5104 1 x - ii a "200K ™ R4D 22 10-5154 1 " . il “ " Ys0K R52 23 10-5224 2 " ad - " "220K" R21,48 24 10-5394 1 ‘ J " moo 390K" R4G 25 10-5474 2 ” " hed ® " 470K ' R22,45 26 10-5105 4 i a " n oa IM " R23,28,47,63 27° | 10-5225 2 RES., CAR. COMP, 5%, kW2.2M " R24,42

30 19-3152541 TRIMPOT, 250K OHMR27

31 19-808W4P0 1 RES., WIREWOUND, 1OW, 4 OHM R211

33 211011031 CAP., MYLAR, 100V .Olufc25
34, 21-1011041 CAP., MYLAR, 100V 0.1lufC37

| __i1— —————_}

FIRETRUCK™ 81

Page 91

82 FIRETRUCK™ etna‘ za" tN Pa re wows avd 37 ¢ Moa TIVE, Sr A Moe Tvs Sd OTST SA¥TS. “HOH ta SoneDeniaT ‘WOM oe WOwa NAS seville ave NossZ00WdoNTTH x 2H 960°ZK “AVLSARD £2 NOILE3SNI “a1 ‘wrE~U9 ‘ZE¥D0S SOKOZNNOD “ERNOK srlar asitoa 45a “TWsEKeaL czewT ‘avatts zew1 “WISaVaH sag ‘26-98 “nN 9 ORES “LNT Sxo0T SRRNSVA, 98 SL¥12 EZRS¥K sgvo ‘07 4x2e-¥e “ha “oH RYE ‘ahaos

WW ee on 91e6 ‘L1NgaL aaLWEDALNT 6a DET LENDHTD ORLVADSLNT (et ‘eonvin9ae w 955 ‘aaNrL, Lo-zzwzeo lo Legeeo Torocneco lors tueeo lo- ewzeo Toro wee lo 6ewec0 To-e2eze0 lo-Leweto 2y-9LLe00 6102-06 1009-06 tol-06 ov0ze-6L To-eva0to 10-02 9020 S909 (we 9090-86 DOLE 9S0-s¢ 90-6 agugT=2e lag I-99 lao 1-99, To-29 cot lat ty olytea'sk oat vatevtenca'e3 roe) et satan unten ectyatsa or a e9 56 {6 ea‘ stato.

woRdHORed west ow <czs1% Esest%e ses gnestae Wwisme ” seis ° mist ” ast : wisi = eyIst . :

gusta ust ow "

eos ish zest ust oest sist ols gost ost, wos A ooste ‘crngers aabvesaieT OCLLSEH AOLSTSIVEL AO¢ OTWaNYE favo AUL -KIWENVE €-a¥2 asi costa "wap 1*a¥9 sé costa 7wa9 f7a¥9 AGZ *DSIa 7W9D *7AVD Ze Ave ortAToIoaTa '*4Vo ASG oLLATOHLOSTS ‘*4¥D e z a > esestac-ue | 8 rezern-ue | ce esestonut | te isestoeee | ue snestne“Le | 08 veistanet | be setstor-ue |e eestye-ut cest9e-ee Orste-ct ynuree titers necosenee aoroserce | 2 worose-c2 ty iecoye-ne | 66

‘wondnoseg

UOIsIaA LO— SIT Sued Add FOUL ary pl-5 ini

Page 92

A, ATARI

1 03092701 2 10-5101 3 10-5271 4 10-5331 5 10-5471 6 10-5681 7 10-5821 8 10-5102

9 10-5182 190 10-5222 ll 10-5392 12 10-5472 13 10-5822 14 10-5103

15 10-5153 16 10-5223 17 10-5273 18 10-5333 19 10-5473 20 10-5683 ah 10-5106 22 10-5154 23 10-5224 24 10-5394 25 10-5474 26 10-5105 27 10-5225

30 19-315254 31 19-808W4P0

33 21-101103

By 21-101104 Figure 5-14 Fire Truck PCB Parts List —02 Version

Description

1 BOARD 4 RES., CAR. COMP, 5%, %W 100 OHM R88-91 3 " woo Tw 970 8 RB,9 41 2 " "om 339 R18 BE 2 “ mm 79 R32 33 L “ a ee re rr en 1 " moon ot gag RST 17 " wow wm AR R1,2,4,15,18-20, 30, 34,39 ,57,61,67,68, 76,108,109 2 ” mow mm Lak © R38,40 3 " "mw oloK 8 R29) 36,60 1 " "oo om mn FZ OK R35 1 " noo om 8 BK RSG 1 " wom mn omg 2K R37 47 7 ww YOK R347,10-13,17,26,56, 59 ,62,65,69,73-75, 77-87 ,92-107,110 1 " wooo om 5K RSO 2 " wow mm BK Ra3,55 z " mom eo FR eo RSB 2 " wom 33K 53,66 4 " Hom IR HM RGOT 70-72 1 " wom ow om Bak RDS 1 " yom om 00K RUD 1 " woo mom 15QK RSD 2 " ww om om 220K R21, 48 1 ” woo BOK RAS 2 " nom mo 470K R22,45 4 " wow tM R23, 28,47,63 2 RES., CAR. COMP, 5%, XW 2.2M R24,42

1 | TRIMPOT, 250K CHM R27 1 | RES., WIREWOUND, 10W, 4 OHM RII

1 CAP., MYLAR, 100V .Oluf 25 1 CAP., MYLAR, LOOV 0.luf c37 %

FIRETRUCK™ 83

Page 93

84 FIRETRUCK™ my octon' Za" EN uw Ee ortat Zuo 0 HOE KYKOLA woee v0 2 Mow TYE woe TIVE oinaivia ‘hoe SOTRERAN-VHaTY “OWS Owa INAS srvttte ‘ave wossa20udoesTx 2W 960°2T “TVISAND NorLeaswy “Gat "NIE-O? ‘L5!D0S OLDARNOD ‘LRNOR aNIog 453 “TWWIHEAL zem tavaus ERENT MATSEVTH sz ‘2e-9¢ ‘nw 9¢ fevas cunt txag1 SemISyA 98 ‘AVIS NTHSYH Smio OT Ax@i~9y ‘Ha vaH HVE ‘ectHOS

Ta fa 6a 916 frnowra aaWeaINT TeGHT “IENDYTD GALMADAINT eH *YORYTONTE oss ‘amnt turseuzco 2260 lo-vewato. le-ezwetu to-1egzco To-ceezeo to-ezezco. To-eze2e0 o-czeze0. To-9T 1603 et0E-06 1009-06 zot-08 or0zr-ez To-ese0c0 10-0z9070 009 t-e 1090-8: ogterse 9S0-S2 sto-se 2909T-2e E1aeTI-99 Elar0-99, 100-29 vteree reenr-oe czeur-ce 9SS-LE cottet ty ots" ea'sk ola ent catcetcut tat tw Lost ow “

cezstHL Eset. Tsest7e sozst1 wis selsiye ISTH 99l9e waist evista istsm ow f sstsim “

ism eotsim 96nd sesi% Cesi% es gesi ow ys ow 7 zest ia zest Lestm ozst% mista oist g0si% 7OSTe zsiz on ry oasis *2rager2 caxveoazNt Ooct2n xOESTSNVaL etext "adoro age Nana ‘249 SB NI NS Ase *28Iq 7waa ‘*a¥D

3010" AS2 ‘9810 t¥30 ‘avo AS2 *281a 7839 ‘avd segte ASZ MROWLOSIA ‘AV BOL " “ Bnet “ ‘ 58L Ase o1LeowLaaTa ‘avo isestm-ie | 98 cezstu-ue | £8 esestenck | 28 Westnet | Te srasmiret | 08 Letsrmeree | 8L seisimnce | persrmece | Le gotunue | 9e vaistverce | $e tetemmnct | istsim-ue | ce esisreenct | te Iststmeee | solstni-1t | 0% gere-ce | 69 sestrc-ce | eo festnnce | 19 testrinis | 99 seste-ue | $9 yestmree | 99 Restvente | 69 cent | 29 zrsim~ie | 19 gestvt-ie | 09 Destve~ce | 6S sist | as oistre-ee | es eostm-it | 9s rostee-ct | SS zoswiret | 96 ooste-ci | 6S ovccark-ve | Is mADINe-9E | OS sosenz-ne | 67 prsena-ec | 80 oentote | ay ano-ez | se owe | om nmeeose-u2 yf porose~1z | zo covose-cz | 19 uezase-ve | ot gotosz-vz | at sezose-o2 | ce sotosz=vz | 96.

woRdHo80q sequin weg | eM nondnroeeg equ seq | mer

UOIsI2A Z70— ast] seg 9d yma any pi-g aang UWL VW

Page 94

TV MONITOR SERVICING

INFORMATION

This chapter provides servicing information taken from the Motorola and TEC service manuals. ach manual has been reprinted by permission of the respective monitor manufacturer.

Your game will include either the Motorola or TEC monitor, depending on their availability during production.

Page 95

M5000-154 M7000-154

MOTOROLA Service Manual

CAUTION No work should be attempted on any exposed monitor chassis by anyone not familiar with servicing procedures and precautions.

A. GENERAL INFORMATION This manual contains information on the MS5000/M7000 monitor series and the +5 volt logic power supply. The M5000 uses a 19-inch CRT and the M7000 uses a 23-inch CRT. All CRTs are of the magnetic deflection type with integral implosion protection.

All monitor power supplies are capable of producing both +73 and ~12 volts regulated from either 115-volt or 230-volt AC input to the transformer pri-

mary. All monitor variations described herein require

a composite video input signal.

Note This service manual refers to the Sky Raider Monitor only

SAFETY

CAUTION No work should be attempted on an exposed manitor chassis by anyone not familiar with servicing procedures and precautions.
  • Safety procedures should be developed by habit so that technicians rushed with repair work automatically take precautions.
  • A good practice, when working on any unit, is to first ground the chassis and to use only one hand when testing circuitry. This will avoid the possibility of carelessly putting one hand on chassis or ground and the other on an electrical connection which could cause a severe electrical shock.
  • Extreme care should be used in handling the picture tube as rough handling may cause it to implode due to atmospheric pressure (14.7 Ibs. per sq. in.). Do not nick of scratch glass or subject it to L any undue pressure in removal or installation. tnput and output connections for the monitors are made through a 12-pin connector plug located at the rear of the chassis. Inputs consist of composite video, audio, and 115/220 volt AC three-wire.

All monitors employ: four stages of video amplification, a two-stage sync separator, a two-stage vertical integrator, a four-stage horizontal sweep circuit, a three-stage vertical sweep circuit, a one-stage spot kill, a one stage blanking amplifier; and a regulated, full-wave bridge power supply.

Model Breakdown Chart

Model Video input | 19" CRT ] 23" CRT IMso00-155 | Composite x IM7000-155 | Composite x

WARNING

. An isolation transformer should always be used When handling, safety goggles and heavy gloves should be worn for protection. Discharge picture tube by shorting the anode connection to chassis ground (not cabinet or other mounting parts). When discharging, go from ground to anode or use a well-insulated piece of wire. When servicing or repairing the monitor, if the cathode ray tube is

replaced by a type of tube other than that specified

under the Motorola Part Number as original equipment in this Service Manual, then avoid prolonged exposure at close range to unshielded areas of the cathode ray tube. Possible danger of personal injury irom unnecessary exposure to X-ray radiation may result.

during the servicing of a unit whose chassis is connected to one side of the power line. Use a transformer of adequate power rating as this protects the serviceman from accidents resulting in personal injury from electrical shocks. It will also

protect the chassis and its components from being

PART NO. 68725253447 @) MOTOROLA Data Products cmotstacannunassner COPYRIGHT 1977 BY MOTOROLA, INC. PRINTED NUS,

Page 96

damaged by accidental shorts of the circuitry that may be inadvertently introduced during the service operation

wi . Always replace protective devices, such as fishpaper, isolation resistors and capacitors and shields after working on the unit.

ES . Before returning a serviced unit, the service technician must thoroughly test the unit to be certain that itis completely safe to operate without danger of electrical shock. Do not use a fine isolation transformer when making this test. gran WOPTHM:VOLT 108 HIGHEREAC VOLTMETE RE NOTES | REPEAT EACH CHECK WITH THE LINE CORD REVERSED IN THE POWER OUTLET. 2 METER READING MUST KOT EXCEED PWOUTS aC

REVERSED IN THE POWER OUTLET HOT” LEAD OF METER TO EACH AS WELL AS THE CABINET

EXPOSED PART OF CABINET,

GROUND LLAD OF METER TO ANY FARTIE GADUND SUCH AS A COLDWATER PIPE Sy

sf

Voltmeter Hook-up for Safety Check In addition to practicing the basic and fundamental electrical safety rules, the following test, which is related to the minimum safety requirements of the Underwriters Laboratories, should be performed by the service technician before any unit which has been serviced is installed in a game again.

A 1000-ohm-per-volt AC voltmeter is prepared by shunting it with a 1500-ohm, 10-watt resistor. The safety test is made by contacting one meter probe to any portion of the unit exposed to the operator such as the cabinet trim, hardware, controls, knobs, etc., while the other probe is held in contact with a good “earth” ground such as a cold water pipe.

The AC voltage indicated by the meter must not exceed 7% volts. A reading exceeding 7% volts indi-

cates that a potentially dangerous leakage path exists

between the exposed portion of the unit and earth ground. Such a unit represents a potentially serious shock hazard to the operator.

The above test should be repeated with the power plug reversed, when applicable.

Never reinstall a monitor which does not pass the safety test until the fault has been located and corrected.

Table 6-1 Motorola Monitor Electrical Specifications

MODEL M5000-155, MODEL M7000-155

PICTURE TUBE 19" measured diagonally (48.2 cm); 184 sq. inch viewing area (1188 sq. cm); 114° deflection angle; integral implosion protection; P4 phosphor 23” measured diagonally (58.4 cm); 282 sq. inch viewing area (1820 sq. cm); 110° defiection angle; integral implosion protection; P4 phosphor standard standard

POWER INPUT 715/230 VAC, 110 Watts (nominal); 60 Hz provision for 230 VAC, 50 Hz b FUSES M5000-155, M7000-155—0.8A

+73 VOLT SUPPLY to 260 VAC Electronically regulated over AC inputs from 103 VAC to 130 VAC, or 260 VAC

VIDEO INPUT 0.5 Volts to 2.5 Volts P/P maximum, composite for 50V at CRT

RESOLUTION 500 lines at picture center + — | LINEARITY Within 3%, measured with standard EIA ball chart and dot pattern

FIRE TRUCK™ 87

Page 97

Table 6-1 Motorola Monitor Electrical Specifications

HIGH VOLTAGE 17KV (nominal)

HORIZONTAL BLANKING INTERVAL 11 microseconds typical fincludes retrace and delay?

SCANNING FREQUENCY Horizontal: 15,750 Hz+500 Hz; Vertical: 50/60 Hz

ENVIRONMENT Operating temperature: 10°C to 55°C (ambient) Storage Temperature: —40°C to —65°C Operating Altitude: 10,000 ft. maximum (3048 meters) Designed to comply with applicable DHEW rules on X-Radiation CSA certified for use in coin-operated amusements in a combustible enclosure UL listed under specification 1410 {electronic components)

TYPICAL DIMENSIONS (35.8 x 46 x 37.6 cm) 14.11" H, 18.18" W, 14.83" D 16.72" H, 21.56” W, 16.18" D {42.4 x 54.7 x 41 cm)

Specifications subject to change without notice.

B. SERVICE NOTES

Circuit Tracing Component reference numbers are printed on the top and bottom of the three circuit cards to facilitate circuit tracing. In addition, control names are also shown and referenced on the schematic diagram in this manual.

Transistor elements are identified as follows: £—Emitter, B—Base, C—Collector.

Component Removal Removing components from an etched circuit card is facilitated by the fact that the circuitry (copper foil) appears on one side of the circuit card only and the camponent leads are inserted straight through the holes and are not bent or crimped.

It is recommended that a solder extracting gun be used to aid in component removal. An iron witha temperature-controlled heating element would be desirable since it would reduce the possibility of damaging the circuit card foil due to over-heating.

The nozzle of the solder extracting gun is inserted directly over the component Jead and when sufficiently heated, the solder is drawn away, leaving the lead free from the copper foil. This method is particularly suitable in removing multi-terminal components.

88 FIRE TRUCK™ CRT Replacement Use extreme care in handling the CRT, as rough

handling may cause it to implode due to high vacuum

pressure. Do not nick or scratch glass or subject it to any undue pressure in removal or installation. Use goggles and heavy gloves for protection. In addition, be sure to disconnect the monitor from all external voltage sources.

  • Discharge CRT by shorting 2nd anode to ground; then remove the CRT socket, deflection yoke and 2nd anode lead.
  • Remove CRT from the front of the chassis by loosening and removing four screws, one in each corner of the CRT.

Adjustments A non-metallic tool is recommended when periorming the following adjustments.

Regulator Adjustment

NOTE

Misadjustment of the +73 volt regulator or

the horizontal oscillator may result in damage to the horizontal output transistor or pulse-limiter diode. The following procedure is recommended to insure reliable operation.

Page 98
  • Connect the monitor to an AC line supply; then adjust supply to 120 volts (240 volts in some applications).
  • Apply test signal to proper input. Signal should be of same amplitude and sync rate as when monitor is in service.
  • Adjust HOR. SET coil L1 until display is stable.
  • Connect a DC digital voltmeter or equivalent

precision voltmeter to the emitter of the regulator

output transistor, Q17, or any +73 volt test point.

. Adjust the 73V ADJUST. control, R93, foran output of +73 volts. Do not rotate the control through its entire range; damage to the mnnitor may result.

Zn . When adjustment is complete, the AC line supply can be varied between 103 and 130 volts AC to check for proper regulator operation. With the regulator operating properly, changes in display size should be negligible

Horizontal Hold/Oseillator Adjustment Adjust the core of HOR. SET coil L1 until the horizontal blanking lines are vertical or the CRT display is stable (synced).

Vertical Height/Linearity Adjustment

  • Connect a test generator whose output is similar to the display signal normally used.

Figure 6-1 Motorola Monitor Circuit Board in Service Position

  • Rotate the vertical size controf, R60, until the smallest display is obtained.
  • Adjust the vertical linearity control, R64, uatil the top and bottom of the test pattern is equally spaced.

4, Readjust R60 until the desired display height is obtained.

  • Readjust R64, if necessary, as in Step 2 above.

Focus Adjustment The best overall focus of the display is obtained by adjusting the focus control, R42, for best facus ata point which is near the center and approximately 1/3 down from the top of the display.

Monitor Servicing The monitor circuit board may be installed in a service position to provide easier access to the circuit foil when servicing the monitor (see Figure 6-1).

Cc. THEORY OF OPERATION Power Supply The power supplies are transformer-operated, fuli-wave, regulated supplies which maintain constant output voltages for input line variations of 103 volts AC to 130 volts AC, or 206 volts AC to 260 volts AC. Regulation of the output voltages is accomplished by using positive feedback through the integrated circuit reference amplifier.

+78 Volt Supply (Sce Figures 6-3,6-4) When the +73 volt supply attempts to increase, the voltage at pin 3 of IC1 will increase, while the voltage at pin 2 remains constant due to D20, The increasing voltage at pin 3 will cause the output voltage of the reference amplifier (pin 6) to increase the forward bias of Q19. The collector voltage of Q19, forward bias of Q18, and the base current of Q17 will all decrease. The resultant proportional increase of Qt17 collector-to-emitter voltage will cancel the attempted output voltage increase.

When the +73 volt supply bus attempts to dectease; the voltage at pin 3 of IC1 will decrease while the voltage at pin 2 remains constant. The decreasing voltage at pin 3 will cause the reference amplifier output voltage at pin 6 to decrease the forward bias of Q19. The collector voltage of Q19, the forward bias of Q18 and the base current of Q17 will increase. The collector-to-emitter voltage of Q17, which is in series

FIRETRUCK™ 89

Page 99
coumostreore:
elrewoe
“eoarenito,ee,Leer
INPUT“OULOWE?dauntedOUTPUT1

‘Woes ono ¢_ ;

woeD

se

MOAR

wonnomeworiznonizwas
——|.Uee‘SsePusOatenotivdlite

wse30 megane wursae fowen

weerSirmct!T

spor |] le t wel

i — 1 yeRr veRr

amcvenventveervery,VERT
natwelt SronRyeieontofr

Figure 6-2 Motorola Monitor Block

wo 64 180 7 a8 nbs 6 gi aay < REGULATOR

at Power 16 soukte neut

ne 09 BLE “tea " sek aatten "693 | re

Beer casft at

Figure 6-3 +73 Volt Supply Circuit with the output, will decrease proportionally to the attempted decrease in the outbut bus.

Resistor R84 shunts a portion of the output

current around Q17 so less power is dissipated within

the device. Resistor R82 is the current-limiting resistor for Q18, and R86 controls the leakage current of Q17. Resistors R83 and R85 are the collector load for Q19, and R88 and R87 provide an emitter voltage for Q19 within the range of IC1’s output voltage variations. Capacitor C45 filters high frequency variations from the voltage at pin 7 of IC1, and C49 is a Miller-effect capacitor which eliminates instability.

90 FIRETRUCK™ PARABOLA FROM EMITTER oF Q17

EXISTING VERTICAL SAWTOOTH WITHOUT VEAT.PARABOLA | ADDED

PARABOLA PULSE AND VERTICAL SAWTOOTH, ADDED TOGETHER, HENCE PRODUCING THE REQUIRED VERT,

DRIVING SIGNAL

Figure 6-4 Motorola Monitor Vertical Drive Waveform

Page 100

+73V +150¥

fay ea

P10 a 1 COMPOSITE ¢ Vineg 1 < [yy wet TT i | 2420 || faaw ono 2 < i

$00 CONTRAST

ToC R13 58K 6.2¥. aan Ss bene

(CATHODE) | ae OF ¥1 RT cad VIA R78

Toa : Taont EAIMER coucgctor

Figure 6-5 Motorola Monitor Video Amplifiers and Output Circuit

Capacitor C32A filters horizontal frequency variations from the output bus.

Resistor R91 provides bias current for D26, and the value of R99 presents an impedance from pin 2 of IC1 to AC ground (through D20). Capacitor C46 couples high frequency voltage variations, which occur at the output bus, back to pin 3—preventing oscillations for proper operation of the reference amplifier. Resistors R92, R93, and R94 provide voltage division such that the adjustment of R93 can be set equa! to the voltage of pin 2 of ICT. Resistor R95 provides bias current for D21 and also provides the +12 volt output. Diode D23 is necessary to temperature-compensate for variations within D21. Capacitor C32B filters AC variations from the output of the full-wave bridge.

Video Amplifiers and Output. (See Figure 6-5) The composite video signal is coupled to the emitter-follower Q1 through the input connector P1 and capacitor C1. Transistor Qt is a buffer stage which matches the impedance of the signal source to the video preamplifer and the sync separator stages. Resistor R1 is a terminating resistor for the video signal source, and resistors R2, R3, R4, and R5 form the biasing network for the stage, Capacitor C2 bypasses higher video frequencies to ground. The composite video signal is coupled from the emitter of Q1to the sync separator Q10 through C33 and ta the contrast control R6 through C47.

The contrast contro} varies the amplitude and couples the composite video signal to the base of Q2 through capacitor C3. Transistors Q2 and Q3 are complimentary, direct-coupled, common emitter amplifiers. The voltage gain (approximately 12) of the preamplifier stage is controlled by the feedback arrangement of R9, R10, R11, and R12. Resistors R7 and RB provide the base bias voltage for Q2. Capacitor C48 is used for high-frequency peaking.

The output of the video preamplifier stage is coupled to the video output stage through capacitor C4. Diode D2 clamps the video signal to approximately +0.7 volts (DC restoration) when a sync pulse turns on the sync amplifier Q11. The video output stage is connected in a cascade configuration. Transistor Q4 is a common emitter amplifier and Q5 is connected in a common base arrangement. Capacitors C7, C8, and resistor R16 are used for highfrequency compensation, and resistor R18 controls the gain of the stage to approximately 47. Diode D3 maintains the base of Q5 at +6.2 volts, while capacitor CS filters the video signal variations from the base voltage. Resistor R13 provides a DC bias path for D2, and R19 and D4 are used to limit the current through the CRT.

FIRETRUCK™ 91

Page 101

n HORIZ DRIVER | ioe 0 was

33K naw

Figure 6-6 Motorola Monitor Horizontal Deflection Circuit

Capacitor Ci0 AC-couples the video from the collector of Q5 to the cathode of the CRT if D4 turns. off due to high beam currents. Resistor R17 is the collector load for Q5, and R15 provides the bias current for the zener diode D3. Capacitors C9 and Co filter video frequencies from the ~150 volt and 412 volt supplies. Resistor Rt4 and zener diode Di are used to supply +12 volts for Q1, Q2, and (3,

D. HORIZONTAL DEFLECTION CIRCUITS (See Figure 6-6) Phase Detector (Sce Figure 6-7) The phase detector consists of two diodes (D5 and D6) in a keyed clamp circuit. Two inputs are required to generate the required output, one from the horizontal sync amplifier, Q11, and one from the horizontal output circuit, Q9. The required output must be of the proper polarity and amplitude to correct phase differences between the input horizontal sync pulses and the horizontal time base.

The horizontal output (Q9) collector pulse is integrated into a sawtooth by R24 and C12. During horizontal sync time, diodes DS and D6 conduct, which shorts C12 to ground. This effectively clamps the sawtooth on C12 to ground at sync time. If the horizontal time base is in phase with the sync (waveform A), the sync pulse will occur when the sawtooth is passing through its AC axis, and the net charge on C12 will be zero (waveform B). If the horizontal time base is lagging the sync, the sawtooth on C12 will be clamped to ground at a point negative from the AC axis. This will result in a positive DC charge on C12 (waveform C). The positive polarity

92 FIRE TRUCK™ causes the horizontal oscillator to speed up and correct the phase lag. Likewise, if the horizontal time base is leading the sync, the sawtooth on C12 will be clamped at a point positive from its AC axis. This results in a net negative charge on C12 which is the required polarity to slow the horizontal oscillator (waveform D).

Components R23, C15, R23. and C17 comprise the

phase detector filter. The bandpass of this filter is chosen to provide correction of horizontal oscillator phase without ringing or hunting. Capacitor C13 times the phase detector for correct centering of the picture on the raster.

Horizontal Oscillator The horizontal oscillator employs the principles of the Hartley-type oscillator. Its operating frequency is sensitive to its OC base input voltage, thus permitting the frequency of the oscillator to be varied by the output voltage of the phase detector. The main frequency-determining components are L1, C19, and R28. The oscillator operates as a switch being biased alternately into saturation and cut-off. The initial forward starting bias is supplied via R26.

Horizontal Pulse Shaper and Driver

The horizontal pulse shaper Q7 serves as a buffer

stage between the horizontal osciliator and driver. Capacitor C20 and resistor R30 combine to shape the input waveform to the required duty cycle of 50%, which is necessary to drive the horizontal output stage.

Page 102

REFERENCE HORIZ. SYNC.

OSC,ON FREQ NO CORRECTION VOLTAGE DEVELOPED

QSC,SLOWS, FOS, CORRECTION VOLTAGE

OSC, FAST, NEG,

CORRECTION VOLTAGE

Figure 6-7 Motorola Monitor Horizontal Deflection Waveforms

The horizontal driver Q8 operates as a switch to driving horizontal output transistor Q9 through T1. Because of the low impedance drive and fast switching times, very little power is dissipated in Q8.

Resistor R35 and capacitor C21 provide damping

to suppress ringing in the primary of T1 when QS goes

into cut-off. Resistor R36 is used farlimiting currentin the collector of Q8, and C22 filters the horizontal frequency variations from the DC side of the transformer primary. Horizontal Output (See Figure 6-8)

The secondary of Ti provides the required low drive impedance for Q9, Resistor R37 limits current in the base of Q9, while capacitor C23 provides additional reverse bias to keep Q9 turned off during the horizontal retrace pulse. Transistor Q9 operates as a switch which once each horizontal time period connects the supply voltage across the parallel combination of the horizontal deflection yoke and the primary of T2. The required sawtooth deflection current through the horizontal yoke is formed by the L-R time constant of the yoke and output transformer primary. The hotizontal retrace pulse charges C27 through D8 to provide operating voltage for G2 of the CRT. Mamentary transients at the collector of Q9, should they occur, are limited to the voltage on C27, since D8 will conduct if the collector voltage exceeds this value.

The damper diode D7 conducts during the period between retrace and turn-on of Q9 to reduce retrace overshoot; capacitor C28 is the retrace tuning. capacitor. Capacitor C25 blocks DC from deflection yoke. Components R38 and C26 are damping components for the width and linearity coils. Capacitor €320 is charged through D10, developing the video output supply voltage.

ce ieae mame au"Puy

Tg RY Pass. Sie Heart SE 1m, Ba wears

Raycae, 2a3beon

= ess & 10 Pmt

aswtpetmeot Bil faceror |
330Kasiveit
anlea eocusontsy}as
— aeRina|| eisf

Te i nt £ oe one I 4 gd weg reo

takBenI
attTales sasoeene

SUSE |uo Jaw ! bu oer

Hes RECT.

Figure 6-8 Motorola Monitor Horizontal Output Circuit

FIRETRUCK™ 93

Page 103

“wy

TO.C%

Figure 6-9 Motorola Monitor Sync Circuit Syne Circuits (Sce Figure 6-9)

The video signal is coupled from the emitter of Q1 to the base of Q10 through C33. The negativegoing sync tips turn on Q10 and are clamped to the value of the base voltage due to the base-emitter diode junction, The video information within the composite video signal, however, is less negative and Q10 remains off between each sync tip. Therefore, the waveform at the collector of Q10 will contain only the composite sync pulse information.

Resistors R45 and R46 provide base bias for Q11.

The composite sync pulses are amplified and inverted

by Q11 where they are coupled to the vertical sync integrator Q12, the horizontal phase detector, and the video clamp diode D2. Resistors R47, R48, and R49, are the collector load for QI, and also provide base bias for Q12. Resistor R50 limits current through the base-emitter junction of Q12, and R51 is its collector load. Components R52, C34, R53, C35, and R54 form a double integrator which removes the horizontal pulses from the composite sync signal, leaving the vertical pulses to be amplified by Q13 and coupled to the vertical oscillator.

Vertical Oscillator and Output (See Figure 6-10) The vertical oscillator is a relaxation oscillator

and operates ata free-running frequency that is set by

+12v +73

SelK:

v4 4Ee i 10 p08 10.013 fed COLLECTOR 201 nw

RS5?. 448 343K: VERT. CB ~ YOKE

$<.)

Figure 6-10 Motorola Monitor Vertical Oscillator Circuit

94 FIRE TRUCK™

Page 104

the value of resistors R56 and R57. The series combination of C37 and C38 charges through D14, R61, and R60, until 012 turns on. This occurs when the anode voltage of D12 exceeds the gate voltage by approximately 1.0 volt. When 012 conducts, C37 and C38 are discharged to nearly zero volts; then 012 turns off and the cycle repeats. The value of R61 and the setting of R60 determines the amplitude of the waveform.

Diode 014 provides a small incremental voltage above ground to overcome the forward base-emitter drop of Q14; 013 provides temperature compensation for the output stage. Resistor R96 provides a constant oscillator load for variations in input impedance of Q14. Transistor Q14 is an emitter-follower used to transform the high impedance drive sawtooth to a low impedance drive for Q15.

The vertical choke L5 acts as a current source during linear scan time and provides a high-voltage pulse to aid retrace when Q15 shuts off. To limit this pulse to a safe value, a varistor, R66, is connected across the choke.

Since the impedance of the choke decreases when the collector current of Q15 increases, severe vertical non-linearity will result unless some compensation is employed.

Resistors R64 and R62 couple the emitter voltage

of Q15 to the junction of C37 and C38. This path is resistive, and the waveform coupled back will be integrated by C38. This results in a pre-distortion of the drive sawtooth. This is done to compensate for the non-linear charging of C37, C38 and the changing impedance of C5. An additional feedback path through R63 and C39 serves to optimize the drive waveshape for best linearity. Capacitor C40 couples the signal to the vertical yoke winding and blocks DC.

Spot Kill (See Figuee 6-11) The spot kill circuitry is used to reduce the effect of the electron beam concentrating on one area of

the CRT after the monitor is turned off. The circuitry is

accomplished by raising the arm of potentiometer R73 to the +150 volt level and, therefore, increasing the brightness to maximum to dissipate the highvoltage charge that normally remains in the CRT.

When the monitor is operating, transistor Q20 is on and its collector is near zero volts. Capacitor C44 charges through the base-emitter junction of Q20 and R97. Resistor R72 provides the base bias voltage

required to keep Q20 on. When the monitor is turned

R13 BRIGHTNESS

TORT? CRT, PIN2

Figure 6-11 Motorola Monitor Spot Killer Circuit

off, the failing +73 volts is coupled to the base of Q20 to turn off the transistor causing its collector voltage to rise to approximately +150 volts. Diode D24 prevents the negative voltage swing at the base of Q20 from exceeding the reverse voltage rating of the transistor.

Blanking Amplifier (sce Figure 6-12) The blanking amplifier combines both the vertical and horizontal retrace pulses to turn off the electron beam in the CRT once every horizontal line and once every vertical field. Capacitor C41 couples the vertical retrace pulses and capacitor C31 couples the horizontal retrace pulses to the blanking amplifier. Resistor R68 determines the amplitude of the vertical pulses, while R69 determines the amplitude of the horizontal pulses. Capacitor C42 bypasses R69 to couple the leading and trailing edges of the horizontal retrace pulses to the amplifier. Resistor R76 allows C41 to discharge when the retrace pulses swing below zero volts. Diode D15 prevents the retrace overshoot from exceeding the reverse voltage rating of Q20. Resistor R71 permits Q20 to turn off between retrace pulses, while R75 and R76 provide the collector voltage for Q20. Capacitor C43 couples the blanking pulses to the control grid of the CRT.

Figure 6-12 Motorola Monitor Blanking Amplifier Circuit

FIRETRUCK™ 95

Page 105

FG (conTRasn Tt

WoRIZ.ose) a7 Rw (hic) FOCUS) 12

96 FIRETRUCK™ Figure 6-13. Motorola Monitor Chassis Rear View —Component Location

Page 106

Figure 6-14 Motorola Monitor Circuit Board Detail—Solder View FIRETRUCK™ 97

Page 107

L

Figure 6-15 Motorola Monitor Schematic Diagram

98 FIRE TRUCK™

Page 108

FIRETRUCK™ 99 Figure 6-16 Motorola Monitor Circuit Board Detaii—Component Location snd04 SH51Na 131 glo £20 ASVHLNOD Sd 1D Id

“LU3A “LydA 9d = ygy {NAAQHS LON) a7 ta {NMOHS LON)

Page 109

Table 6-2 Motorola Replacement Part Numbers

REF. PART

NO.NUMBER|DESCRIPTIONAGNuMBERDESCRIPTION
Capacitors:C318S10191B9807, 10%, 250V; Poly.
All values are in Microfarads unless otherwise noted.| C3223510255B7320/200, 400/125, 600/100,
ca238102552747, SOV; Lytic200/50; Lytic
C2219135660.05, +80-20, Z3V, 50V;C338S10791A51-033, 10%, 160V; Poly.
Cer. Disc.C34,C35851019132.——_.047, 10%, 250V; Poly.
C3,C4238187A2622, 25V; LyticC3621S180E60-01, + 80-20, Z5V, SOV;
C521S 180E6001, +80-20; Z5V, 50V;Cer. Disc.
Cer. Disc.C37, 38,39 8S10191B670.22, 10%, 250V; Poly.
cé218135660.05, +80-20, Z5V, 50V;c4023510255A60100, 63V; Lytic
Cer. Disc.cat85102128160.1, 20%, 400V;; Mtlz.
C7218131625330pf, 10%, X5F, 500V;Poly.
Cer. Disc.C4221$180C820.33, 10%, N150, 500V;
ce21S180B87220pf, 10%, X5F, SOOV;Cer. Disc.
Cer. Disc.C438S10191B67(0.22, 10%, 250V; Poly.
oo8510191B99015, 10%, 250V; Poly.C4423510255B284.7, 100V; Lytic
C108S10212B180.22, 10%, 400V:cas8810191890033, 10%, 250V; Poly.
Mtlz. Poly.C4621813249201, +80-20, Z5V, 100V;
cit218131625330pi, 10%, XSF, 500V;Cer. Disc.
Cer. Disc.caz23510255B63100, 10V; Lytic
C12218180C410027, 10%, Z5F, 500V;C4821818005647 pt, 10%, N750, 100V;

Cer. Disc. Cer. Disc.

C13218180C0210pf, 10%, N150, 500V;C49218180B51-001, 10%, XSF, 500V;

Cer, Disc. Cer. Disc.

C14218180D34.003, 20%, Z5F, IKV;

Cer. Disc, Diodes:

CIS23$10229A321.0, 16V; Lyticot48510813A03Diode, Silicon, Zener;
C78S10191B90——.033, 10%, 250V; Poly.IN5242
C188510299B28——.01, 10%, 100V; Polycarb, | 2248D67120A13—Diode; A13
C198S10299B29_.0082, 10%, 100V;D348510813A01Diode, Silicon, Zener;

Polycarb. IN5234B

208510191B9801, 10%, 250V; Poly.D448519102Rectifier, Silicon; 91A02
C2121S180B51001, 10%, XSF, S0OV:Ds, D648D67120A11_Diode; A17
Cer, Disc.o7485134921Diode, Damper; DiD
C228S10191B98-01, 10%, 250V; Poly.bs48S 134978Diode, Pulse Lim; DIK
O2323810255B50150, 10V; LyticD1048S191A05Rectifier, Silicon; 91405
2421$180B51001, 10%, XSF, 500V;Dit485137114Rectifier, H.V., D2Y
Cer. Disc.D12485137638Vert. Osc.; MPU6027
C2585102998270.82, 10%, 200V; Mtlz.D13,D14485191405Rectifier, Silicon; 91405
Polycarb,DIS48D67120A11Diode; A11
C26218131625Pe a XSF, 500V;Bie iG 485191A05Rectifier, Silicon; 91A05
C278S10212A111.0, 10%, 630; Mtlz.D2048510813A02 ~—- Diode, Silicon, Zener;

Poly. 1N5231B

C288S10571A06.01, 5%, 1200V;D248510813A03Diode, Siticon, Zener;

Polyprop. Foil 1N5242

C298S10212B530.47, 10%, 630V; Mtlz.D2248D67120A11Diode; A11
Poly.023,D2448S191A05Rectifier, Silicon; 91A05

a

100 FIRE TRUCK™

Page 110

Table 6-2 Motorola Replacement Part Numbers

Ref.

RePart No.|DescriptionasPart No.|Description
Fuses:R6018D25245A29Vert. Size; 250K
Fr F2658136269Fuse, 0.8A~250VR6418D25245A31Vert. Lin.; 100K
_R666510201A04—_Varistor, 1 ma, 120V, 0.5
integrated Circuits:R?318025245428Control, Brightness; 200K|
Ic151810732401Ref. Ampl.; T3FRa4178135589150, 10%, 10W
ROB18D25245A21Control, >73V out Adj.

Coils/Chokes: 28K

ul24C25448A01Coil, Horiz. Osc.R951073140315K, 10%, SW
224D25603A09Coil, Horiz. Width
324025248414Coil, Horiz. Lin.Switches:
u2AD25261409-Coil, Defi. (M5000-155,Swi40510624A07Switch, Stide; D.P. D.T.

5010-155)

La24D25261A10Coil, Deft. (7000-155,Transformers:
7010-153)1125025271405Horiz.Driver
625D25221C12_Choke, Vertical224025240823H.V. Transformer
.TB25D25239B20Transformer, Power

Transistors: (M5010-155, M7010-155)

Qt485137171Emitter Follower; A6HB25025239830Transformer, Power
Qn488137172Video Pre-Ampl.; A6)(m5000-155, M7000-155)
Q@3488137127Video Pre-Ampl.; P25
Qa485134952Video Driver; A2}Misc. Electrical Parts:
Q5aahTa7476Video Output; BIEvA965241401——-19"-CRT; Type 19VARPA
26485137172Horiz. Osc.; A6](M5000/M5010)
Q7485137127Horiz, Pulse Shaper; P2SVI96510848A01—23”~CRT; Type
Q8485137093Horiz. Driver; ASEM22VATP4 (M7000/
Qo485137570Horiz. Output; B2tM7010)
Qi488137173Sync Separator; P2W
Qu488137172Sync Ampl.; AGlMechanical Parts:
Qn485137172Vert. Sync Integrator; A6)9B25456A01Block, Fuse (F1, 2)
Qs485137172Vert. Sync Ampl.; AG)4202513801Clamp, Defl, Coil
Qu485137639Vert. Driver; MPS A132651025108Heat Sink (QS)
Qis485137596Vert. Output; B2VPI15510183A69 _— Housing, Connector;
Qt485137172Blanking Ampl.; A6]Female (12-Contact,
Qy7488137368Regulator; ABWLess Contacts)
Qs485134952Reg. Driver; A2)39810184467Contact, Plug; 5 Req'd
Qi485137476Reg, Buiter; BIEMS000/M7000, 9 Req'd;
Q20485137476Spot Kill; BIEMs5010/M7010
P21581018382Housing, Connector;

Resistors /Controls: Male (3-Contact, Less

NOTE: Only power or special resistors are listed. Use Contacts), M5000/M7000
the description when ordering standard values of |pp15810183481Housing, Connector;

fixed resistors up to 2 watts. Female (Contact, Less

Ro18D25245A27—Contros, Contrast; 500Contacts), M5010/M7010
Rid178135204100, 10%, 5W39510184467Contact, Plug; 3 Req'd
RI7178107310013.9K, 5%, SWfor P2
R3617$10130B071.5K, 10%, 3WP328510586A35Header, Connector;
R4218D25218A14_—Control, Focus; 2M2-Contact

FIRE TRUCK™ 107

Page 111

Table 6-2 Motorola Replacement Part Numbers

REF. PART REF. PART

NO. NUMBER DESCRIPTION NO. NUMBER DESCRIPTION

P4, PS15S10183B12Housing, Connector;14B25459A01Insulator, Fuse Cover

Female (3-Contact, Less (Fi, 2)

Contacts) M5010/14562353Insulator, Mica (Q9,

M7010 Q15, Q17)

39510184A84Contact, Plug; 3 ea.14C25230A01Insulator, Molded (On

Req'd for P5, M5010/ D11 Body)

M701014510157A30Insulator, Nylon (2-
$215810183A81Housing, Connector;Req’d.); Mtg. P.C. Board
Female (3-Contact, Less14S10550A02Insulator, Transistor

Contacts), M5000/M7000 Cover (Q9, Q15, Q17)

$215910183A82Housing, Connector;38136050Screw, Tpg; 6-20x'%2 CLU

Male (3-Contact, Less Pan (Mtg. Q9, Q15, Q1I7 Contacts), M5010/M7010 and B11 Socket)

39510184A64Contact, Receptacle;9D25470A01Socket, CRT; Inc's.

3 Req’d. for $2 R77, R78, R79, R80

3315$10183A94Housing, Connector;9D25201A01Socket, H.V. and CRT

Female (2-Contact, Less Anode

Contacts}9C63825A03Socket, Power Transistor
39510184472Contact, Receptacle;QF, Q15, Q17)

3 Req‘d. for $3 41D65987A01 — Spring Special; CRT Aquadag God.

102 FIRE TRUCK™

Page 112

A. GENERAL

TM-600 and TM-623 is a television monitor for video games. It is designed for operation either from a power supply of 115 volts/50-60 Hz AC or 230 volts/ 50-60 Hz AC. The complete monitor incorporates a picture tube, an integrated circuit, 20 silicon transistors, 18 silicon diodes, 2 germanium diodes, anda high-voltage selenium diode.

This model is equipped with 5V/3A power supply for the operation of the TTL control board and operation double-pulse-type AFC circuit to obtain a stable picture.

B. SPECIFICATIONS Power Supply Input 115 volts/230 volts 50-60 Hz +10%

Power Cousumption 60 watts

Video input 0.5 volts composite P/P for 100 volts 2.5 volts P/P maximum Sync negative at input TEC VIDEOELECTRONICS INC, SERVICE MANUAL

Picture Tube 19" (500 mm), 114° deflection for Model TM-600 23" (584.2 mm), 114° deflection for Model TM-623 Integral implosion protection

Thigh Voltage 18 KV nominal at 0 microamperes beam current

Horizontal Retrace Time 12 microseconds maximum

Resolution 500 lines minimum at picture center

Scaning Frequency Horizontal: 15.750 Hz £500 Hz Vertical: 50-60 Hz

Tone Burst Amplifier 5 watts peak output with TTL drive at nominal fine, fully adjustable. 4 watts peak output at low fine.

Environment Operation: Maximum ambient temperature 50°C (122°F) Storage: Temperature range from -40°C to +65°C

Model TM-600 and TM-623 Monitors

TEC Videoelectronics Inc. (TV) 3010 Scott Boulevard FIRE TRUCK™ Santa Clara, CA 95050 103

Page 113

Deetection CENTERING omy uw YOKE ou one.

HY Aker.

Switch —Fy93 SANE. By DAMP. Connector

Figure 6-17 TEC Monitor Chassis, Rear View

esos came Vv REGULATOR connensea TOR asoy a»

REGULATOR ca CONDENSER

~

4 = 9208 Na Vent. our TRANSISTOR

Fransiston

very um,

POWER TRANS. ver

so: Resistor eRiGHT ERT. HOLD.

Figure 6-18 TEC Monitor Chassis, Top View

104 FIRE TRUCK™

Page 114

ving oureuT

a+any WORIZ. DRIVER TRANS.

HOR. OUTPUT

Hv meer

HY TRANS,

vent Bauance

worn con

Figure 6-19 TEC Monitor Printed Circuit Board, Top View

Table 6-3 TEC Monitor Replacement Parts Numbers

Ref. . Ret ;

a PartNo. — Description No, PartNo. Description

Electrical Parts:3035300500201MPS9700U_Vert Amp
PCB12215303600Main PCBalee
‘A801485TM60003«CRT PCBQ3044310400030«281106Vert Output

Q305 or 2N6307

Transistor and IC:4005310500202MPS9700TPhase Inv
Q2005310500202= MPS9700Tist Video Ampor MPS834
‘or MPSQ4015310500202MPS9700T—Horiz Osc
Q2015310500261MPS9730T2nd Video Ampor MPS834
or MPS435640253105004102N6558Horiz Amp
2025310500410= 2N6558_—Video Outputor MJE9742

or MPSU-10 or 2N4354

Q3015310500261MPS97S0TSync Separator4035310400040 = 2SC1875.——Horiz Output

‘or MPS4356 or Mj205

Q3025310500201MPS9700U__Vert Osc%Q9015310400030281106 ~—- Power Regulator

or MPS834 or MJ3430

FIRETRUCK™ 105

Page 115

Table 6-3 TEC Monitor Replacement Parts Numbers

ReePartNo.DescriptionigPart No.Description
ae eneculaRegulator AmpT401589514015TLN-506BX Horiz Ose
Qo03 5310500280LM1796.Reference AmpT402589578012TIN-519—Horiz Drive
or MPS-DO1* 7403589517017TEB-1006AS_F.B.T.
045310500850«M2955.«SV Regulator* 7901589579021TPW-600Power Trans

CRT and Diode: Resistors

* yeor5380000060-—«§00SB4.«SSRR201RD-4L474)470 ohm} % W
D2035340200280MR9712__Silicon DiodeR202RD-4L223)22.Kohm.| 4 W
or IN4Q04LL. V. RectifierR203RD-41563)56 K ohm |W
D204 5340200430:IN4#48.—_—_Silicon DiodeR204RD-4L471}470 ohm] %W
or IN4002_Blanking ClipR205RD-4L332)3.3. K ohm) %& W
D205 5340200430IN4148__Silicon Diodey206_RD-21873)82K ohm} 4 W
or INA002Blanking ClipR207RD-4L560)56 ohm) 4 W

D206 5340200430 ~=——«IN4148.—_—sSilicon Diode

or IN4002Blanking ClipR208RD-4L102)1K ohm] % W
D207 534020280MR9712_—-200V RectR210RS-029562)5.6 K ohm } 2 W
cor IN4004R215—RD-42101)iKohm J %W
D3015340200260MR-9701_—_—Rectifier Silicon* R216RD-ALT01)100 ohm) %W
Diode* R217RO-4L470)47 ohm| 2 W
D40T5349700040 © AAT43Phase DetR218RD-41223)8 Rochen | BAR
D4025340100040AAT43Phase DetR219RD-AL563)56K ohm | % W
D403.5340200300 «= MR9722.«DamperR220RD-AL102)tKohmjWw
*D404 5340400120TV20-2K80)_H.V. RectifierR221RD-AL102)tKohmJ “Ww
—R222RD-2L102)1K ohm | %W
D8015340200290«M973.«AO RectifierfoRO21102)TK ohmy Yew
D9015340200270—«sMRO704-——Rectfier
or IN&005Silicon DiodeR224RD-2L122)12K ohm) 4 W
D902 5340200270 = MR9704—éRecctfier* R226RSOIPTON100 ohm) 1W
or IN4005.Silicon DiodeR227RD-2L123)12K ohm) %W
D9~3 5340200270=—«MR9704_—séRectifierR226RD-21105)15 Kohm) 2 W
or IN4005.—_—_Silicon DiodeR229RD-4ME8I]«680 ohmJ 4 W
Oe 5 Keeee odeR302RD-4M331)«330 ohm J 4 W
D906 5340300220INSBS8A_—Zener DiodeoeeRTey
pee nrR304.RD-4M102)1K ohm) %& Ww
poo7:R308RD-4M1D4}.100 K ohm | % W
Boos 75340200690MDA970-1_RectifierR302RD-4MI55T—-1.8Mohm] % W
p90.R310RD-4M332]3.3 Kohm | % W
Coilsand TeanssR311RD-4M563)56 K ohm | % W
#La0T 589515015TDY1005DY. CoilR312RD-4L 182)1.8K ohm J 4% Ww
L402589512015HCHi005 — Horiz ChokeR13RD4L 133)15 Kohm | %W
CoilR314RD-4L183)18 Kohm | % W
L403.589512012HC2-035Choke CoilR315RD-41203)20K ohm J % W
Lag589512012HC2035Choke CoilR316RS-2P333)33 K ohm J %& W
L405589574013AZ-SI77DM Width CoilR327RD-4L104)100 Kohm | % W
L406589514016LH-15/54Lin CoilR320RD-4L124)120Kohm | % W

106 FIRE TRUCK™

Page 116

Table 6-3 TEC Monitor Replacement Parts Numbers

eiPart No.DescriptionPart No.Description|
R322RD-4L224}220K ohm | % WR904RD-2L123)12K ohmj % W
R323RD-41433)43 Kohmj % WR905RD-21.223)22Kohmj % W
R324.RD-4L471f470 ohm} % WR906RD-21563}56K ohm) % W
R326 = RD-4L152)1.5K ohm} % WR907—-RED-2L563}56K ohm} % W
R339RD-4L101)100 ohmj % WR909 —- RD-2L68256.8K ohm) ¥: W
R331RD-4M331}330 ohm) % W
R332RD-4L102)1K ohm J %WControls:
R333RS01P682)6.8 K ohm | 7 WR211553102005E1K ohm = Contrast
R334RD-2L183)18 Kohm) %WR319SSB 1040058100Kohm = Vert. Hold
R336RD-41221)220 ohm} % WR3215531240088220Kohm Vert Height
R337516012290122 ohm) %Waad—4.7K ohm Vert. Linearity
R33951601129017.2 ohm| %W.~
R340RS01P220T22 ohmj1WR8033532540058250Kohm = Bright
R401RD-4L153]18K ohm) %*WR80555320500582Mohm_ focus
R908553472007847Kohm B-ADS
R402,RD-4L821j820 ohm) % W
R403RD-4M561)560 ohmJ % WCapacitors:
R404RD-4M1103)1Kohm) %WC201CE2G1C47047 mF16V
R405RD-4M103)10K ohm} % WC202.CE2G1F101100 mF25V
R406RD-4L272)2.7Kohmj) 4WC203CE2G1€22022 mF16V
R407 - RD-4L681)680 ohm) % WC204CE2GIHT0T106 mF35V
R408 = RSO2P682)4.7 Kohmj %W205CE2G1C22022 mF16V
R419RD-41270)27) ohmj %W€206 CISL1HS6iK360 pF K50V
R410 = RD-4L182)1.8K ohm) %WC207CE2G0)221220 mF6.3V
R411RD-4L151)150 ohm| %WC208 = 5270322401O22mFM 400V
R412RD-4L567)560 ohm| % W€209 CE2G2F2292.2 mF31SV
R413RSO1P682}6.8K ohm) 1 WC210CE2G1H22022 mF35V
R414RD-24221)220 ohm) % W©21CE2G1H3393.3 mFSOV
R41551601229032.2 ohm} iWC213)CKIF2H102K0.001 mFSO0V
R416RO-21569)5.6 ohm) 2WC220CE2G2F2202.2 mF250V
R417RSO2P182)1.8K ohm | 2WC301=CQIM1H473K0.047 mF K 50V
R418 = RSOTP123)12 K ohm) 1 W304 CKIBIH39IK470 pF KSOV
*R420 — RXO5P220)22, ohm)SW305)CE2G1H4780.47 mFSOV
*RA21—RD-2L569}5.6 ohm} &WC306 564053330.033 mF K SOV
R422RD-4L153)47) ohm} 7 WC307 CQIMIHS62K(0.0056 mF K SOV
R425RD-4L.153)15 Kohmj % WC308 =CQIMIH273K0.027 mMF K SOV
R426 = 5533715315Kohm) %WC309 CQIMIH123K«0,012 mF K_ SOV
R862 —- RD-24.154)150 Kohm j 4 WC311CQIMIH124KO12 mF KSOV
R804 = RD-21474)470 Kohm J % WC312CQIMTH392K0.0039 mF K 50V
RBMRD-2i561)2MO) % WC313,DSSD1C229M2.2 mF16V
R901RX20P254)250 ohm } 20 WC314CQUMTH474)0.47 mF50V
R902RD-2L101)1K ohms %WC315CQIM1H333K0.033 mF KK 50V
R903.RD-21123)12K ohm J %WC316 CF2G1A47047 mE10V

FIRETRUCK™ 107

Page 117

Table 6-3 TEC Monitor Replacement Parts Numbers

Ref. No Part No. Description Ref.

C317 CE2G2A101

C318 CK1E2H103K

C319 5270310301

C401 CQIMIH103K

C402 CQIMIH103K

C403 CQIM1H393K

C404 CK1B2H151

C405 CE2G1H339

406 CQUIMIH104K C407 CQIM1H223K

408 CQUIM1H683K 409 CERG1F470

C410 CK1B2H681K

C411 CKIB2H222K

C412 CK1B1H152K

C413 CKIBIH102K

*C414— CK1B3D471K

C415, CQIM2A104K *C416 — $270333201 C417 CE2G2C100

C418 5270333401

C419 56635101

C420 56625471

C801 5270356302

*C901 5240700400

C904 F2G2C229

C905 CKIF2H102k

C911 56625105

C912 56616018

Discharge Gaps: Z801 za} 599030007 2803

Switches: *SW-1— PE13-1567 100 mF 100V

0.01 mF 500V

0,01 mF 630V

0.01 mF K SOV

0.01 mF K 50V

0.039 mF K 50V

150 mF 500V

3.3 mF 50V

0.1 mF K SOV

0.022 mF | 50V

0.068 mF J 50 V

47 mF 25V 680 pFK — 500V 0.0022 mF K 500V

0.0015 mE K SOV

0.001 mF K 50V

470 pF K 2kV

0.1 mF K 100V

09,0033 mF 1.5KV

10 mF 160V

0.33 mF K —200V

160 mF 35V

470 mF 25V

0.056 mF K 630V

450 mF ———200V

100 mF 160 V

2.2 mF 160V

0.001 mF 300

10000 mF 25V

Tm 16V

EGP-H751A

115V/230V Power Line

Slide Switch

No.Part No.Description

Fuses:

*F9026990620011250V 2 Amp.
*F9035990610013250V 0.5 Amp.
F*4599063001030V 5 Amp.

Mechanical Parts: *K001

or

K005

pani

Paoz

A621

Ab3t

P406

pagr

TEON

+OO01

Foor

HOO3

Q403 22463020 Mate-N-Lock Connector (AMP) 60085005, Edge Collector (Molex) S-A3915 Transistor Socket (SMK) *7M60085001 Fuse Holder *TM60085001 Fuse Holder

1-380826-0 Stand-Off Fastener (AMP)

PF19- 1569 4P Plug Assy. (Yoke Line) PEI9-1570 4F Recep Assy (Yoke Line) PE19-1571 3P Connector Assy. {Video

Inpury PEI9=1572 4P Connector Assy. (Q901 Line)

PEI9-1573 6P Connector Assy.

(Q304/Q305 Line)

PEIO-1574 2P Plug Assy. (Heater Line) PE19-1375 2P Recep Assy. (Heater Line)

PL19-1576 Terminator, 6 Pin

135431013 Ground Plate 22-164001 frame 5432001-1 Plate Heat Sink A

1D 54320011 Plate Heat Sink C

NOTE

2, Design and specifications are subject to change without notice.

J--Indicates + 5% tolerance

K-—Indicates #10% tolerance

M-—Indicates 20% tolerance

108 FIRE TRUCK™

Page 118

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 119
WARNING Safety-Critical Components Components marked with an asterisk (*) on the parts list and with gray shading in the schematic have special characteristics important for safety. You may create shock, fire, or other hazards by using a replacement that does not have the same characteristics as the recommended part.

y201-, tow 823 | TRW-600

‘TR, IC, and Connector Lines

(rs) MPS UO4 ups 9750 UPS 9700 146002 A

wieiO8 mses7ae if

. ry 2

Of oF

M2085

110 FIRE TRUCK™ Sa | paper EnReaeEE |

ane ESE «i

Page 120

NOTES

  • Unless otherwise specified, all resistance values 4. All waveforms are measured with strong signal are in ohms. input and contrast set to give normal picture.
  • Unless otherwise specified, in the schematic dia- 5. This schematic diagram covers basic or repregram alt capacitor values less than 1 are expressed sentative chassis only. There may be some differin mfd, and values more than 1 are in pfd. ences between actual components on chassis and
  • Voltage readings are taken with VTVM from point the schematic diagram. indicated on chassis to ground.

Figure 6-20 TEC Monitor Schematic Diagram

FIRE TRUCK™ 111

Page 121

Beal bed Oo Boc6 it gE 7 9305 ¥

a che A ‘

kno

112 FIRE TRUCK™

Page 122

a s « a : | ? o fat o> h 3 vu ke 0901-904 \"* (1 > | Hy R90! ae Ort woe t O: HT Os

BOTTOM VIEW

Figure 6-21 TEC Monitor Wiring Diagram

FIRE TRUCK™ 113

Page 123

tl

Cut along this line

TM-115, Ist printing

YOUR COMMENTS, PLEASE!

Your comments will assist Atari in improving the usefulness of our publications. They are an important part of preparing for revisions of manuals and parts catalogs. No postage stamp is necessary if mailed in the U.S.A. If you have any technical questions about certain Atari or Kee Games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.

Page: Comments:

Fill in if you wish a reply:

Name Firm ( Distributor (1 Operator Address ——- ( Other

City State Zip

Page 124

First Fold

First Class Permit #1004 Sunnyvale, CA Se fe a ae ee ee es he es ee ee ee

&

FS

Atari, Inc. :

P.O. Box 9027 8 Sunnyvale, California 94086 8

Attn.: Publications Group, Coin-Op Engineering

PTT TTT TS Second Fold SSti—CSs—<“—=Ss~s~—SsSSSSS 7

98066 VO ‘ajeAkuung 1206 XOg ‘O'd “oul ‘ery

e6pz siy edey

Page 125

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.