CATHODE RAY TOMES

Berzerk

Berzerk (revision RC31A) (Stern Electronics, 1980) · Manual · 34 pages · 11 sections · original scan

Page 1

° ELECTRONICS, INC. 1725 Diversey Parkway, Chicago, Illinois 60614 (312) 935-4600, Telex 25-4657 Toll Free Service Assistance (800) 621-6424

Page 2

1.1. INTRODUCTION

This game has been STERN final tested and is ready to play, but on all games there are some items that must be checked first after shipment. Making these visual inspections may avoid time consuming service work later. Minor troubles caused by abusive handling in shipment are unavoidable, such as cable connectors that may have been loosened. Check ALL CONNECTORS on the game to make sure they are firmly seated. Examine the exterior of the game cabinet for dents, chips or broken parts. Check all major subassemblies, control panel and T.V. monitor to make sure that they have not loosened up during shipment. :

1.2 VISUAL INSPECTION BEFORE PLUGGING IN LINE CORD

  • Check that the primary wiring of the transformer corresponds to the location voltage (See Figure E).
  • Check the transformer for any foreign material shorting across wiring lugs.
  • Check that fuses are firmly seated and making good contact.
  • Check the T.V. for any foreign material that could cause shorts (VISUAL INSPECTION ONLY).
  • Check game boards for any foreign material that could cause shorts. Make sure all circuit boards are connected properly.

1.3 ON/OFF POWER INTERLOCK SWITCHES

  • The on/off power switch is located on the top right side 12” from the front.
  • There are two interlock main power switches, one by the front door (See Figure A) and one on the back access panel (See Figure B).
  • Interlock switches interrupt all power from game except service outlet and flourescent lights for Marquee. Interlock switches can be locked in “ON” position by pulling stem out when servicing game.

1.4 GENERAL INFORMATION

  • On the front door there is a bookkeeping switch (See Figure A). Depressing this switch will step through bookkeeping functions one at a time for each time switch is pressed. Pressing fire button will clear whatever bookkeeping function you are in. (See Page 14 for bookkeeping function).
Page 3

. There are two coin chutes on the front door. They can be adjusted to work separately. (See Page 13). . Game adjustment switches are located on ZPU board. (See Pages 10, 12 & 13 for adjustments and location). . Volume control for electronic sound is located inside the front door on right side. (See Figure B). . Power supply has an adjustment for the +5 VDC regulator, this MUST BE SET BETWEEN +5.0 VDC and +5.25 VDC as measured at TP4, VSU-1000. (See Figure D for test points on power supply and adjustment pot).

Page 4

FIGURE - A

BERZERK FRONT CABINET

SPEAKER

CONTROL PANEL

SEE FIGURE - C FOR SLIDING DRAWER DETAIL

INTERLOCK SWITCH

LOCKING ASS'Y, FOR SLIDING DRAWER DOOR BOOKKEEPING SWITCH

Page 5

FIGURE - B

BERZERK REAR CABINET

ON/OFF SPEAKER SWITCH

INTERLOCK SWITCH

FLUORESCENT 4 FUSE ASS'Y.

CONVENIENCE OUTLET

VOLUME CONTROL

Page 6

SLIDING DRAWER ee <

ADJUSTMENTS & FUSES

\to REMOVE SLIDING DRAWER CABINET

  • REMOVE ONE LOCKING SCREW FROM BACKSIDE THAT LOCKS SLIDE IN PLACE
  • REMOVE SLIDE RETAINER BRACKET THAT IS HELD ON WITH TWO SCREWS REMEMBER TO REPLACE THESE ITEMS IF GAME IS TO BE MOVED SA/ NORMAL OPERATION JUMPER MUST BE IN NORMAL POSITION FOR GAME TO PLAY,— RESET BUTTON ‘ FREE GAME BUTTON SEE PAGE 10 SEE FIG. -D

DIP SW. BANK F2- ——4 DIP SW. BANK F3- co DIP SW. BANK F4- —— DIP SW. BANK F5-C——)) DIP SW. BANK F6-C——) VARISTOR Oo 130V FOR 115VAC LINE -’ 250V FOR ZPU-1000 220 VAC LINE

LINE 120V/240V FILTER JUMPER

oO BOARD

BSC-1000

POWER AND sB-1000 [] ISOLATION 7 XFMR.

VFB-1000

DIP SWITCHES SEE PG. 10 SEE PAGE 8

Page 7

NOTE:

+5 V ADJUSTMENT MUST BE

BETWEEN +5.00 & +5.25 VDC

(MEASURED AT TP4, VSG-1000)

samantha Ov BQOGE cee

TP-1 +5V +5 VDC ADJUST.

(SEE NOTE)

HEATSINK

TP-2 ~5 VDC oe co a cD cms)

Ag G3unidv anny ONY GINDIS3G +18V #10V =5¥ REGULATORS

noe net aed Ane aoe rors Ase nannn Ase” TP-4 +12 VDC GRD +15 VDC P-5 TP-3 000l~-Sd ‘AdY A,SSV 899-V FIGURE D

Page 8

FIGURE - E

TRANSFORMER STERN 16D-13

13124 3 21

JUMPER

115 VAC 220VAC 130V VARISTOR 250V VARISTOR FOR 115 VAC LINE FOR 220 VAC LINE

Page 9

J-1 6 12-PIN 7

J-2 5 10-PIN 6

J-3 6 12-PIN 7 = D o a

s|<s oe a

£555 OBH< Cc

<

vu < z =

Dv s§ General Ill. General Ill. Volume Control High

Bookkeeping Volume Control Low Coin Door Common Siam Coin 1 Coin 2 Coin 3 Spare 12-PIN

Spare Spare Fire Joystick Left Joystick Right J-6 10-PIN

Player 2 (Cocktail version only) Joystick Up Joystick Down +5 to PRU Control Panel Commo

Two Player Start

One Player Start Fire Spare Ground Joystick Left Joystick Right Joystick Up Joystick Down Spare +5 to PRU Control Panel Common 12-PIN

Speaker High

Speaker Low Video SYNC Red Green Blue Spare Video Ground Video Ground J-8 10-PIN To Monitor

Page 10

OPERATION

Insert coin for credit. Start game by pressing START button. Object of game is to have Humanoid Intruder shoot as many Robots as possible and escape from room. Humanoid Intruder is controlled by player with control stick. (Eight directions possible). Note: Humanoid Intruder stops moving when shot is fired. Shot is fired in direction Control Stick points to. Bonus Score for each room full of destroyed Robots (even if Robots destroy each other). EVIL OTTO comes out from position Humanoid Intruder started, cannot be destroyed will go thru walls, and follows Humanoid Intruder with its object to destroy the Humanoid Intruder.

SW. 1 RESET

F2|F2|F2|F2|F2|F2 | F2 | F2LOC. F2

1/2/3}/4/si6j)7]8 BANK

F3|F3|F3/F3]F3/F3 | F3 | F3 LOC. F3 1/2/3/4/sle]/7]8 BANK

=

F4|F4 | F4F4]F4|F4 | F4LOC. F4
1]2/35|6]7]8BANK

F5|F5|F5|F5|F5|F5]F5 | F5 LOC. F5 4/,2/3]}4]/5]/6;/7]/8 BANK

F6 | LOC. F6 [Fe F6 | Fé} F6 | F6| F6| Fe

4}2/3)4])/5)1;6)7)8BANK

FREE GAME SWITCH

(BOOKKEEPING)

Page 11

ADDITIONAL SWITCHES

ELECTRONIC BOARDSSWITCH NO.PINSUSAGE
BSC11-8Breaks WAIT line for SIGNATURE

ANALYSIS (S.A) MUST BE Closed for game operation

2-7 Adjusts color outputs for the variations in 3-6 monitor input circuitry 4-5 SHOULD BE: OPEN FOR WELLS-GARDNER CLOSED FOR ELECTROHOME Pon

VFB 10011-8NOT USED.
22-7Breaks NMI line for S.A.

MUST BE Closed for game operation

33-6Breaks INT line for S.A.

MUST BE Closed for game operation

44-5Breaks WAIT line for S.A.

MUST BE Closed for game operation

SB 100011-8Breaks WAIT line for S.A.

NOT USED 2-7 3-6 NOT USED 4-5 NOT USED PON

JUMPER OPTIONS

$B 1000: JUMPER W1 MUST BE CONNECTED (W2 OPEN)

VSU 1000: JUMPER W3 MUST BE CONNECTED (W4 OPEN)

ZPU 1000: J8 PINS 2-3 MUST BE CONNECTED TOGETHER

CHIP LOCATION 1E MAY BE POPULATED BY ANY ONE OF 3 DIFFERENT CHIPS

CHIP STERN PART NO. CONNECT JUMPER

6513 H56A-6-S004Ws
6513 L56A-6-S003we
651456A-6-S002wit
Page 12

FREE GAME SWITCH (SW. #2)

Switch #2 (printed on board “Bookkeeping Clear’), if pressed when HIGH SCORE TO DATE IS DIS- PLAYED will provide one game without being added on any coin bookkeeping.

MONITOR DIP SWITCH AND GAME SWITCH DISPLAY TEST

Set dip switch 9 on the ZPU board (location F3, See fig. D) to “ON” position, then press the RESET button (SW. #1, located at F1 on the ZPU board). The monitor will display the OFF (0 on the monitor) ON (G on the monitor) status of the 40 “ZPU DIP SWITCHES” on the upper chart and the open (0 on the monitor), closed (C on the monitor) status on all game switches on the lower “VFB SWITCHES” chart.

SEE BELOW FOR ZPU AND VFB SWITCH ASSIGNMENTS. (SEE PAGE 13 FOR DIP SW. DESCRIPTION) (NOTE: GAME SWITCHES CAN BE TESTED BY CLOSING AND SEEING IF CLOSED DISPLAY SHOWS UP ON MONITOR CHART). To return to normal operation set dip switch 9 to OFF position and press RESET (SW. #1) button on the ZPU board.

NOTE: The usage of these switches will be explained in the Stern Video System 1000 Signature Analysis Manual.
123745678
Normally | NormallyON forON forBANK
OFFOFF*>..ExtraExtra
Zz(On for(On forMan atMan atFe
PSA. Tests) | SA. Tests)5,000
u9101"12131415
ON forON seeCoin
OThisNote for....Instruct. | Instruct.a
'DisplayCrosshatch|Transla-Transla-3
P+ Resettiontion
s1718192021222324
wCOIN CHUTE #1——____—_BANK
|CREDIT/COIN SET-UP‘**.F4

T REFER TO SETTING TABLE Cc

H2526272829303132
sCOIN CHUTE #2——___-____....BANK

CREDIT/COIN SET-UP F5 h REFER TO SETTING TABLE |

T[3334353637383940
3COIN CHUTE #3 ——__—....BANK

CREDIT/COIN SET-UP F6 REFER TO SETTING TABLE ——_I VFB SWITCHES (SHOWS SETTINGS) [on WHEN | ON WHEN | ON WHEN | ON WHEN | ON WHEN

VFBJOYSTICK | JOYSTICK | JOYSTICK | JOYSTICK | FIRE*..
AT LEFT | AT RIGHT | UPDOWNPRESSED
blON WHEN | ON WHENON IFON IFON IF
1START 1 | START 2COINCOINCOIN
TPLAYER | PLAYER*...CHUTE #3|/CHUTE #2/CHUTE #1
c1S ON1S ON1S CLOSED) IS CLOSED}IS CLOSED|

H (IF USED)

STATUSiJ**>.*..

O = SWITCH OFF (OPEN) = SWITCH ON (CLOSED)

  • = NOT USED
NOTE: Cross hatch pattern is used for Monitor setup pushing Fire Button will cause a red screen to check purity.
Page 13

ZPU DIP SWITCH

SWITCH NO. LOCATION FUNCTION SW. #1.......0.cc cece eee Fo... ie esr rastecaaae Signature analysis mode (service only) SW. #2 F2 Signature analysis mode (service only) Sw. #3 F2 N/U SW. #4.........0 cee eee Fe os ection sop eneeuen ¢ N/U SW. #5 F2 N/U SW. #6 F2 N/U SW. #7 F2 Extra man at 5,000 SW. #8.........0. 0c eee FQ cece eee een eee Extra man at 10,000 SW. #9...... 0... cece eee a ee eee ee Switch test (See Page 13) SW.#10 F3 Cross hatch (See Note Below) SW.#11 F3 N/U SW.#12 F3 N/U SW.#13.... 2... cece i eee ee N/U SW.#14 F3 N/U _ SW.#15 F3 Coin Instruction Translation SW.#16....... 0... e ee eee FS: apes aie gee o oce ote ew ore Hane (See Page 14) SWAT cece eee eee FA Lecce eee eee Coin SW.#18 F4 Chute SW.#19 F4 #1 SW.#20 F4 See Page 13 SW.#21 20... eee eee a N/U SW.# 22 F4 N/U SW.#23 F4 N/U SW.#24.... 0. FA caecictsnervianseanaces N/U

SW.# 25.0.0... cece eee ee FS cece cece eee eee ees Coin SW.#26 FS Chute SW.#27 FS #2 SW.#28 FS See Page 13 SW.# 29.2... eee eee ee FE ccc cence N/U SW.#30 FS N/U SW.#31 FS N/U SW.#32... 2... cee ce eee FS on ats easa eden re: N/U SW.#33......0..00 0c eee | Coin SW.#34 F6 Chute SW.#35 F6 #3 SW.#36 F6 See Page 13 SW.#37... 0... cee eee eee F6 owe eee eee eee N/U SW.#38 F6 N/U SW.#39 Fé N/U SW.#40. 2... cece eee FG on. ame ssa i cao e rw, N/U

NOTE: Cross hatch pattern is used for Monitor setup. Pushing the Fire Button will cause a red screen to check purity. Pushing the Fire Button again will cause a return to the crosshatch pattern, etc.
Page 14

DIP SWITCH ADJUSTMENTS

CREDIT/COIN ADJUSTMENTS:

The credits given are selectable by means of ZPU switches. Sixteen credit ratios are available. The ZPU switch settings and resultant credits/coin are as follows:

COIN ZPU SWITCHES CHUTE No. 1 20 19 #18 17 (BLUMWHITE) LEFT CHUTE No. 2 28 27 «(26 25 (BRN/WHITE) CENTER CHUTE No. 3 36 35 34 33 (RED/WHITE) RIGHT CREDITS COIN OFF OFF OFF OFF.......1 OFF OFF OFF ON........2 OFF OFF ON OFF 3 OFF OFFON ON........4 OFF ON OFF OFF (Bivcceees 1 OFF ON OFF ON. .6 OFF ON ON OFF 7 OFF ON ON ON.......10 ON OFF OFF OFF 14 SEQUENCE OF CREDITS CREDITS COINS PER COIN 1 2 3 4 ON OFF OFF ON........ Leveeeees 2 iecccceees 0...4 ON OFF ON OFF 3 2 1 2 ON OFF ON ON........ Bieceeeee Qe 0....5 ON ON OFF OFF 7 2 0.7 ON ON OFF ON........ Bee Bivccceeeees 0....1..0...2 ON ON ON OFF 5 4 1 11 2 ON ON ON ON........ Tiveeeees re 1...2..14...3

If two or three coin chutes are adjusted the same for multiple coins, credits will increase as if dropped in same chute.

SIGNATURE ANALYSIS MODE (SERVICE ONLY) SW. #1 & 2

See the “Stern Video System 1000 Signature Analysis Manual.”

SW. #7

When score of 5,000 is achieved a Extra Man can be awarded.

5,000 SCORE AWARDS _EXTRAMAN ON OFF sw. #7 NO x Sw.#7 YES x

EXTRA MAN BONUS (SW. #8)

When score of 10,000 is achieved a Extra Man can be awarded.

10,000 SCORE AWARDS EXTRAMAN ON OFF sw. # 8 NO x SwW.# 8 YES x

SWITCH TEST (SW. #9)

With switch in “ON” position, monitor will display “OPEN” or “CLOSED” position on each Dip Switch and Game Switch (See Page 11 for diagram)

Page 15

BOOKKEEPING

Inside the coin door is the BMDS (Bookkeeping Monitor Display Switch) - (See Fig. A). Depressing this switch one time initiates this function. The first bookkeeping function to appear on the monitor is number of credits (*Green). To delete from memory press either Fire Button. Depressing the BMDS one more time will advance the bookkeeping up (*Blue), and the second bookkeeping function (total coins thru coin chute #1) will be displayed on the botton (*“Green). To delete from memory press either Fire Button. The previous bookkeeping functions will remain on the screen (*Blue) and the new function will appear on the botton (*Green). Bottom function can be deleted from memory. Following is a complete list of bookeeping functions.

*Color of display if color monitor is used.

FUNCTION DESCRIPTION DIGIT DISPLAY

1)CreditsTotal Credits~00
2)Chute #1 (Left)Total Coins00000000
3)Chute #2 (Center)Total Coins00000000
4)Chute #3 (Right)Total Coins00000000
5)PlaysTotal Number of Plays000000
6)ScoreAccummulated Score000000000000
7)Time PlayedTotal Amount of Time

Played (in seconds) 000000000000

8)High ScoreHigh Score To Date000000

COIN INSTRUCTION TRANSLATION (SWS. #15 & 16)

Will say in different language correct coinage

SW.-#15 SW.-#16

ENGLISHOFFOFF
FRENCHOFFON
GERMANONOFF
SPANISHONON
Page 16

TROUBLE SHOOTING BY SELF-TESTS

PERTINENT INFORMATION

  • The following tests occur each time the RESET button is momentarily pressed or when power is removed and re-applied.
  • The self-test indicating LED is on the ZPU-1000 board (CR45) and each indicating flash is accompanied by a tone from the sound system.
  • The LED stops flashing at the malfunction provided all PC boards are connected in the system.
NOTE: If the ZPU-1000 board is not connected to the VFB-1000/BSC-1000 board combination, the self-test program will continuously cycle and counting LED flashes is meaningless. Also, if the SB-1000 board is not connected, or if it is defective, no self-test tone will be generated.

FIRST SELF-TEST

The first of 8 LED flashes occur accompanied by a tone from the speakers. This first test analyzes the ROM circuits on the ZPU board.

ANALYSIS OF FIRST TEST WHEN LED STAYS ON

Continuous illumination of the LED indicates problems in one or more of the following areas:

  • The POWER-ON RESET circuit. Check NAND gate 7G, inverter 8G and associated circuits.
  • Loss of clock signal. Check oscillator transistor Q12, flip flop divider 8A and other associated components. . Microprocessor (Z-80) is defective (Chip 7B). .. Defective Address Bus (shorted or open) or control buffers (chips 6B and 7D, type LS244). . Defective ROM chip(s). . Defective 1/O Decode Circuits. Check chips 5A, 4A, 6A, 7G and decoder 7E. '. Defective LED latch. Check chips 7G, 3A, and 8G. NQOos w

Analysis of First Test when LED Flashes Once and stays OFF. This sympton indicates the problem is in one or more of the following areas.

  • Defective PROM circuitry. Check all PROM chips since the malfunction may be in any one chip.
  • Defective Address Decode Circuit. Check chips 6E, 4A, 5A, 6A and 8G.
Page 17

SECOND SELF-TEST The second of 8 LED flashes should occur accompanied by a tone from the speaker. This test analyzes the “scratch pad” area of the RAM on the ZPU-1000 board. For the following diagnostics, the LED must flash twice and extinguish.

ANALYSIS OF SECOND TEST

NOTE: All following chips are on the ZPU-1000 Board.
  • Check RAM CHIPS 1E and 2E.
  • Check transistor Q2 and associated components/circuits.
  • Defect in gating chips 2A, 3A and 6A. 4. Check that the jumper used for chip 1E (W5, W6 or W11) is correct for the particular chip part number. See page 10 for jumper options.

THIRD SELF-TEST The third of 8 LED flashes should occur accompanied by a tone from the speaker. This test analyzes the RAM (screen RAM) located on the VFB-1000 board. For the following diagnostics, the LED must flash three times and extinguish.

NOTE: The following chips are on the VFB-1000 Board. “4. The CRT will display a RAM chip location map which will indicate a defective chip. Mentally rotate the map 90 degrees counterclockwise to properly orient the map with the lower right hand portion of the VFB-1000 board. If the defect is not located, use the following steps: . Check the +12V and -5V voltages, specifically to the VFB-1000 board. . Check RAM address Multiplexers 6F, 6G, 6H and 6E. . Check the RAS* and CAS’ circuits: chips 4, 7E, 1G, 5G and 5F. . Check the “RAM write” circuits: chips 5F and SE. . Check the Address/Arbitration circuits, chips 5G, 5F, 7E, 3F, 1F and 2D. Check that switch 2B (contacts 4 & 5) is set to the ON position.
  • Check the “magic” enable circuits of chips 7B and 5C.
  • Check the “write” data path of chips 7A, 8A, 10A, 11A, 12C and 10C.
  • Check the “Read” data path of chips 10D, 11D and 6D.
  • Checks all Bus connectors, especially J1 and J2 on both the VFB-1000 and BSC-1000 boards. aah wn

*Denotes negative true logic

Page 18

FOURTH SELF-TEST The fourth flash plus a tone test the RAM circuits on the BSC-1000 color board. IF the LED stops on the fourth flash, perform the following listed tests:

NOTE: All following chips will be on the BSC-1000 board.
  • Check RAM chips 3B, 2B, 1B, and 2A.
  • Check the Address Multiplexer chips 4C, 4B and 4A.
  • Check that DIP Switch 2F (pins 4 & 8) is set to the ON position.

FIFTH SELF-TEST The fifth flash plus tone test the Shifter/Flopper circuits on the VFB-1000 board. If the LED stops on the fifth flash, perform the following tests.

  • Check Shifter/Flopper chips 7A, 8A, 9A, 10A, 11A, 8B, 9B, 10B, 11B.
  • Check ENABLE gates 7B and 5C.
  • Check control latch 6C.
  • Check “OLD DATA” latch 7C.
  • Check Port Decoder 4D.

SIXTH SELF-TEST The sixth flash plus a tone tests the Arithmetic and Logic Unit (ALU) and the intercept circuits on the VFB-1000 board.

NOTE: All following listed chips are on the VFB-1000 board.
  • Check ALU chips 12C, 10C.
  • Check ENABLE gate 5C.
  • Check the Intercept gates 12A, 12B.
  • Check Flip-Flop 6B and associated gates of 5G and 1H.
Page 19

SEVENTH SELF-TEST The seventh flash plus a tone tests the Interrupt and Non Maskable Interrupt (NMI) circuit portions which are on both the ZPU-1000 and VFB-1000 boards. When the LED stops at the seventh flash, perform the following tests: . Check that Dip Switch 2B (pins 3-6 and 2-7) is set to on. . Z-80 microprocessor. . Interrupt generating circuitry 1G, 3D, 2D. . Time Gating circuity 1E, 2F, and 2E. . NMI ENABLE Latch 1D. : . NMI generating circuitry 2E, 3E & 2D. Oahron =

EIGHT SELF-TEST If the LED indicator and associated tone have occured eight times, the malfunction is either in a circuit that is not within the testing capabilities of this self-test program or the problem is unique such as an intermittent condition that changes with physical movements or temperature. After eight flashes have been obtained, try the game to see if the problem has been removed by the check-out action. If the game operates properly, it is advisable to attempt to locate the former problem by checking all connectors for tightness. Also lightly tap various areas while viewing the CRT. If eight flashes have occurred and the game is still inoperable, the following information outlines the circuits that are not part of the self-test routine and must be verified by other test methods:

  • Check the settings of all DIP switches on the ZPU-1000 and VFB-1000 boards by setting switch $9 (on ZPU-1000) to ON and then pressing the RESET* button (on ZPU-1000). The CRT will display the ON/OFF conditions of all switches which must then be checked against the Installation and Operating manual data.
  • Visual analysis of the CRT pattern (when it is available) can provide many clues to circuit operation as described in the following paragraphs. Total loss of the CRT display usually indicates problems in the monitor itself.
  • Malfunctions in the horizontal or vertical address counting circuitry, or SYNC generator circuits will cause “bad” video to be displayed. Vertical or horizontal stripes should give an indication of where the error is. A rolling or flipping picture is an indication of SYNC problems, either in the monitor or on the VFB-1000 board SYNC circuits.
  • Color splotches are an indication of a malfunction in the color gating circuitry, or a monitor problem. Check BSC-1000 board chips 2C, 1C, 2D, 3D, 3E and associated switches and resistors.
Page 20

SOUND SYSTEM PROBLEMS

  • NO SOUND; Check amplifier 8C on the SB-1000 board. Check VAUDIO (+15V MAX).
  • Voice is normal but there are no sound effects: Check the 6840 chip on the VSU-1000 board. On this board check that Dip Switch 10B (pin 1-8) is in the ON condition. Check the addressing and timing circuitry chips 6A, 8A, 9B, 9A, 9C, 10C, 8A and 10B. Any other malfunction will result in either the loss of a specific sound or, a change in a sound and can thus be identified as a related circuit.
  • Sound effects are normal but there is no voice: Check VSU-1000 chips: CRC ROM chip 3C, PROMs 1C, 2C, clock generator 5A, 6A, decode & control logic 1A, 2A, 3A, 4A, 2B, 5B, 6B, 6C. Also check the -10V supply (on the board). Distorted Noise: check PROM 1C, 2C, CRC ROM chip SC, filter & amplifier 5C.
Page 21

RF INTERFERENCE PROBLEMS

Warning: This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instructions manual, may cause interference to radio communications. As temporarily permitted by regulation it has not been tested for compliance with limits for Class A computing devices pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference. Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures may be required to correct the interfernce.
Page 22

Sa #° ELECTRONICS, INC. + 1725 Diversey Parkway, Chicago, Illinois 60614 a (312) 935-4600, Telex 25-4657 Toll Free Service Assistance (800) 621-6424

Page 23

TO MAKE USE OF “STUD LOGKING "4170" 3M_COMPANY

Eaees 3) = a

@é) wore: SCREW MUST NOT

BE SCREWED DOWN TIGHT. @)

JA-911 MUST BE FREE TO PIVOT. USE “STUD LOCKING’ *4170 3M COMPANY ON SCREW THREADS.

CONTROL STICK ASSEMBLY

Page 24

PART NO, DESCRIPTION

/ “GasesPLASTIC HANDLE/
2 | 2A-325-BTHREADED ROD!
3SPACER/
4WASHER/
5MOUNTING PLATE/
| @ | /A-809SPACER2
7#8-32x 2p LG. SLOT FLAT H. SCREW4
8 TA- 136RUBBER SPACER -/
9 | 2A-33/SPACER4
10_| 34-195WASHER2
i} | 2A-329SPACER/
12 | 1A-893PLATE/
13. | 24-334SPACER8
14 | 2A-332SPACER/

i5_| 44-364 | FIBER WASHER 4

16 | PRU-/000PC. BOARD ASSEMBLY/

17_| 2A-326-1 | THREADED SPACER [4

18 | 1A-906LIMIT PLATEn
19 | 2A-328CONICAL WASHER/

20 | 3A-/96 EXTERNAL SHAKEPROOF LOCKWASH. | 2

21 | 1TA-169JAM NUT2

1A-911 SPRING HOLDER | 2 5A-182 SPRING B-80/ JOY STICK BOX ASS’Y. 3A-135 SPLIT LOCKWASHER 6X32 x3 S.H.W.H. TREAD FORMING SCREW

Page 25

12G-5-132

12D-708-S/12C-719-S

12D-661-S/12D-665/S

12D-668-S/12D-788-S

12D-660-S/12D-766-S

12D-809-S

12B-339

OR

K-4615-5808

12B-2-132-23

OR

12B-2-132-25

OR

12B-2-132-27

OR

12B-2-132-29

8A-111-P75

8A-111-1

8A-111-3

8A-111-5 BERZERK PACKING LIST

Catalog

Schematic

Schematic

Schematic

Schematic

Schematic

Electro Home

OR

Wells-Gardner

English Instruction Card

OR

French Instruction Card

OR

German Instruction Card

OR

Spanish Instruction Card

%4 Amp Slo-Blo Fuse

1 Amp Slo-Blo Fuse

3 Amp Slo-Blo Fuse

5 Amp Slo-Blo Fuse

12A-253-132

Page 26

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 27

REVISIONS

DESCRIPTION

ISSUED EI. 00326

‘0P8707

BOTTOM VIEW

. SCHEMATIC PHOTO REFLECTIVE PC BOARD

120-719-8

Page 28

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 29

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 30

REVISIONS.

DESCRIPTION A. | TSSUED, EX. 00265

  • 33 a ~~

Len7g UNREG 2 +5 Voe REG

Z 4s vos RES

y AS woe RES

HEAT SINK @ REGULATC . SHoWh FOR REFeRErice oniy Te. 5 -SV REG NOT LOCATED ONE.C. BOARD! © +1aV REG A= |00o wns 4 7 +\2V Ree lo | 8 -sv Res leg liver + VA I 9 aNd SqQ323 I 10 Gb +——> 1 and

12 +9, {AUDtO) wey ——b9 13 Key 4s: UNREG >it Los pts js-y.57 UINRe L aaa Zasy 4 i

i i

[re es = LOIN Te . a ia PRY 5.60 Sw

1_START. et . cas Fl cr aa Pi : Wicod ASB. | .OIHRLT Ta 3 STRAT, _— +> 1 47.79 UNRG Fhe

  • $Bo0, iF ot a 4 IDE, fed, CRE = 35V 2 +5 Vbe Fre, INYOO4 299-Gat > 3 45voC FE, md To! 4 45 VRC FES

5 -5V Ae @ Hav REG 7A BEG

8 -5v REG

@ GND

jo GRD

th Guo \2+8sy (aubro) 13 KEY

(448.5) UNREG desi ISWI49, UNRES

SCHEMATIC, POWER SUPPLY

l2d-668-5

Page 31

REVISIONS

DESCRIPTION

ISSUED E.T. 99389 A

q g

‘° r-—|-—- 1A ‘oo

S|

SCHEMATIC, RESISTOR CAPACITOR RESISTOR PC. BOARD 12D-788-S

Page 32

REVISIONS,

DESCRIPTION

ISSUED EI 00324 DRAFTING ERROR E.I. 00390 "ADDED MISSING INFORMATION E.T. 09441

E ill ED]

s beg is

zal ELpae

‘F

we

‘oH a Dion ects Fiat geeseRebelesz2 LEP in we SPARE GATES

2|5}~|~{~]4|4]5]+]~]~|~|i5]0|0]0|0]0]55]5|5|0

SCHEMATIC, VIDEO FRAME

BUFFER PC, BOARD

12D-660-S

Page 33
K3HGEDCcBA

REVISIONS:

é sym DESCRIPTION p | IQ, COMPLETE PRODUCTION [= MATIC E.T. 00433

Nae9RED

| AL 6 _ Az 7 GREEN \s : Pus_N

(a2sue

[Hse KY [Hee | | [| ls HLINTENS

||lso57SPARE GATES

| [Cor A8_Sto5 AS 10|5 7 A? Blan 6

fzhi, 48 :®

N —_

iva_NSlo,av.+5,
eHUsaGED
adioc1,c2,¢3,c4,c5,c7,¢8,09, 4] ce
aaPjoo 1c19,cil,ciz,¢13,c14,cis,Sout/
Oy ts287asC16, CI7,C18,cI316V

lor iala> Blut

he42 I3lag
18yjos ila,
Alo 1014,bee(SEE NOTE)
Nyan oyeremarkTone vlVen5
usahae36002700
ve4 ilont1RIS
[westtsa ee4=k BRP>o84
iBOtses7}ifisio“74060a

| ee) | :

1] 20Use2,le
rL800™es

1A 10,

ioartawT ip switches F2-2,F2-3, a F2-4
BittyReeRigSHOULD BE OPEN WHEN USING WELLS

SAV 9 VV — 4 5 GARONER MONITOR, CLOSED FOR

36002702ELECTROHOME MONITOR.

5 2. FOR NORMAL OPERATION SWITCH

4ssi6.vy;F2-1 SHOULD BE CLOSED.
3Dse—o
[ oeLs1074067500
3 2pi Shee 8GREEN
if1.8007406

(SEE NOTE) ts273 | 20 |

ok at RelBI ays2e7 | 16 | 8
' 3600]2700useas | 20 | 10
9,us744Ei
io]83Ra.use7_|14 | 7

eT 2 ‘Sia usio [| 4 | 7 usoa | 4 | 7 seo [14 | 7

7406147
5‘74147

5 2a | is | 9 | 2 pe US BLUE 5-3)

a7406+5v | GND
{sookey GDto. 1¥PE Fe

7 SCHEMATIC, BUFFER aT oo SYSTEM COLOR P.C. BOARD l2D-766-S

LKJHGryEDcBA
Page 34

ZPU—1000

+5V|

vauDIo|

VATEN

GND TO SHIELD VA 77 SOLDER LUG TO COLOR MONITOR —120 VAC ISOLATED PI-6_) 120 VAC ISOLATED

XFORMER

O T

‘TWO, PIN INLINE. ‘CONNECTOR er SB-1000

VOL CONTI

VSU-1000

y3—1 BSC - 1000

VFB -1000 3 PIN INLINE PSL CONNECTOR

To SHIELD VIA SOLDER LUG

RCR-1000 ‘TO SHIELD

EARTH GND 1—2 ‘TO SHIELD ®

FOUR POSITION 3a. 0 TERMINAL STRIP IN CLIP RTH bills + aCe ACHI(pi-4_) ==4 PRI | LO) _ 1 VARISTOR AND TERMINAL a STRIP JUMPERS VARY WITH | FILTER LINE VOLTAGE (JUMPERS = SHOWN [20 VAC OPERATION)

= + Ac Low

SYNC (COLOR) OR VIDEO (8 AND W) (5-4) SPKR HI Je-1 >) BLUE (NOT USED FOR B AND W1-—jg—7~) SREEN (MoT USED Flin’ 8 ANE Wise) RED (NOT USED FOR B AND W) —Ja=—— SPKR LO ~Fa-3) VIDEO GND (jag) VOL CONT LO

COIN DOOR COMMON J5=7 SENERAL ILL (“J5-1_) GENERAL ILL (s5=3) Vou_CONT HI (“F5-3) BOOKKEEPING (“J5-5 ) COIN 1 COIN 2p cow 3 5

TWO PLAYER START (—7—, ONE PLAYER START (—J7=3) +5V_TO PRU

CONTROL PANEL COMMON FIRE . JOYSTICK vow et JOYSTICK UP. JOYSTICK naire JOYSTICK LEFT 9 PIN MALE AMP

COMPONENT DRAWER WIRING DIAGRAM 120 -899-S