CATHODE RAY TOMES

Under Fire

Under Fire (World) (Taito Corporation Japan, 1993) · Manual · 22 pages · 15 sections · original scan

Page 1

| ThITO | TAITO AMERICA CORPORATION | 390 Holbrook Drive Wheeling, IL 60090 Telephone: (708) 520-9280 Fax: (708) 520-1309

Page 2

TABLE OF CONTENTS

Introduction

Specifications «= aeaneseenersensenseenee 2 Game Installation sosseeseseseeeeneseeseess 3

Ploy lnistrUGtionis =§»-—«—= Cis tgnsnasnasesnonnnencosinn 3 Test and Switch Settings —«-—saeaveseassesecusneneees 4-11 Configuration Settings «= caaseeaesessesssesseneees Z Gun Assembly 12

Gun Assembly Parts List 13

Front Replacement Parts 14

Front Replacement Parts List 15

Rear Replacement Parts List 16

LED Box Assembly —saaaeeeaestaeseneeescneee ihe

® AITO TAITO AMERICA CORPORATION 390 Holbrook Drive Wheeling, IL 60090 4 TM, “TI Telephone: (708) 520-9280 Taito™ and Under Fire™ Fax: (708) 520-1309 are trademarks of Taito Corporation.

Page 3

_—k_—~—~E = °°...

INTRODUCTION

Game inspection

Please take a moment to read the following before turning on your new Under Fire™ for the first time. Your game was carefully checked at the factory before shipping.

After removing the game from its carton inspect the game carefully. Look for cracks in the cabinet, gouges, bent metal parts, etc. This shipping damage should be reported to the carrier. Remember to take photographs.

Let the machine warm to room temperature before plugging it into the socket.

Precautions conceming the place of installation

This is an indoor game machine. Absolutely do not install it outside. Even indoors, avoid installing in places mentioned below so as to ensure proper usage:

« Places subject to rain or water leakage, or condensation due to humidity. In the proximity of an indoor swimming pool and/or shower. Places subject to direct sunlight. Places subject to heat sources from heating units, etc., or hot air. Vicinity of highly flammable/volatile chemicals or hazardous matter. Sloped surfaces. Vicinity of anti-disaster facilities such as fire exits and fire extinguishers. Places subject to any type of violent impact. ¢ Dusty places. ¢ Residential environment - (See F.C.C. statement which follows). oece eee

Page 4

F.C.C. Requirements

The Federal Communications Commission requires that all Class A equipment be verified and labeled as follows:

This equipment complies with the requirements in part 15 of FCC Rules for a Class A computing device. Operation of this equipment in a residential area may cause unacceptable interference to radio and TV reception requiring the operator to take whatever steps are necessary to correct the interference.

This label must be permanently attached in a conspicuous location and the text must be legible. If this label is removed or tampered with such action is punishable under Section 503 of the Communications Act of 1934 (ACT), as amended.

—LL __ ~2«»*«O*° ©...

SPECIFICATIONS

Power Line: 120V AC 60Hz Consumption: 250 Watts (approximately)

Monitor

Type: 27" Color, Raster-Scan Inputs: RGB, Composite Negative Sync

Cabinet Height: Ta" Width: 29-1/2" Depth: 39"

Caution: For safe operation it is strongly recommended the cabinet be properly grounded. The game is equipped with a three conductor power cable. The round "third prong" will ground the game when plugged into a grounded. outlet. If an adaptor is used, be certain to attach the grounding lug or wire on the adaptor.
Page 5

GAME INSTALLATION

Prior to using Under Fire™, carefully follow the notes below:

1 Adjust the body position of UnderfireTM so that beams of lighting instruments or other lights (such as sunlight) are not directly in the line of the gun point of Under Fire™. 2 When installing two sets of Under Fire™ side-by-side, provide enough space between them. 3 When any of the front glass, mirror, monitor, gun point or the filter section of the LED box (black plastic plate) is stained, the gun may miss-hit the targeted position during the game.

To prevent this fault, always clean these positions. Special care is required not to make any scratches while cleaning the gun point and the filter of the LED box.

3 Although Under Fire™ is adjusted to the optimum condition at the factory before delivery, there may be some deviation of image size, image display position or color fade on the monitor screen in some installed locations. Adjust the monitor by referring to the Monitor Test instructions on page 4.

SS

PLAY INSTRUCTIONS

Under Fire™ is played as follows:

The object of the game is to score as many points as possible by shooting the enemy. When you pull the trigger once, three bullets are shot at one time. When you push the button on the side of the gun, it becomes a shotgun. You have 24 bullets in the magazine, and must reload the magazine when it's empty by aiming the muzzle of the gun toward the outside of the screen and pulling the trigger. You may reload at any time during the game.

To increase your ability to get a higher score, capture bonus weapons by shooting them as they appearing during play. Your number of bullets will then increase for longer play. There are three kinds of bonus weapons. You may increase your score greatly by using the fully automatic machine gun bonus weapon.

Page 6

—— ——<S~SC<CS;3;7;7C;C;C;3ZETCS:é‘<Cai‘; <7 tT

TEST AND SWITCH SETTINGS

Test Mode

To start the testing procedure, open the coin box door and locate the test mode switch:

Coin Meter Test Service

Oo Oo

Press the test mode switch and the game enters into test mode. Select any of the items using the start button of 1P or 2P, and then pull the trigger of the 1P or 2P guns. The menu screen will look like this:

TEST MODE MAIN MENU

MONITOR TEST

SWITCH TEST

SOUND TEST

CONFIGURATION

MOVING TEST

GUN SIGHT TEST

FACTORY SETTING

EXIT

a

Monitor Test

This mode is to adjust the display image on the screen. Both “cross-hatch"” and “color-bar" displays are provided. To change display between these displays, pull the trigger of the 1P or 2P guns. Press the 1P or 2P start button to return to the menu screen.

Page 7

Switch Test

This test is to check the ON/OFF operation of each switch and button. When the 1P and 2P start buttons are pressed, the respective lamp goes on. Simultaneously press both the 1P and 2P start buttons to return to the menu screen.

es 2 ae

Sound Test

This test is to check the sound output and adjust the volume level of the game. Select the required item by pressing the 1P or 2P start button.

“SOUND NO”

“SOUND VOLUME”

“EXIT” Pull the trigger of the 1P or 2P gun to change the figure. When you press the shotgun switch of the 1P or 2P gun, you can check the sound output.

Pull the trigger of the 1P or 2P gun to change the figure. When you press the shotgun switch of the 1P or 2P gun, you can check the sound output.

Press the trigger of the 1P or 2P gun and the confirmation screen appears. When you want to change the sound volume level, select “YES” (pull 1P gun trigger) and press the start button of 1P or 2P to make the sound volume level return to the previous setting. After pressing the start button, the screen returns to the menu screen.

Page 8

rr

Configuration

This mode is to determine the various settings. Select the required items by pressing the start button of 1P or 2P and change the set contents by pressing the trigger of the 1P or 2P gun. The screen will appear as follows:

CONFIGURATION

CABINET TYPE UP MONITOR TYPE :NORMAL SIGHT MODE tREVERSE VIOLENCE MODE ‘NONE ATTRACT SOUND :ON DIFFICULTY :NORMAL

BUY-IN PRICE SAME AS PLAY PLAY PRICE :1 COIN 1 CREDIT

Lines marked with an asterisk (*)are for the North American Market. For product specifications for markets other than North America, these two lines become:

COIN-A :1 COIN

21 CREDIT

COIN-A :1 COIN

21 CREDIT

Page 9

rr I)

Configuration Settings

Item Set Contents

*UR No alternative

*Normal Use mirror (image is symmetrical for left & right) Mirror Don't use mirror (normal display of image) *Reverse When a bullet mark remains on the reverse Normal side from that targeted, set this as "Reverse" *None No blood scatter display even when shooting enemies or civilians

Violence ModeNormalDisplay one blood scatter for each hit of en-

emy or civilian

Display the same amount of blood scatter as the number of shots

Attract Sound*OnEmit demonstration sound

Off Do not emit demonstration sound Easy

*Normal 7 (Difficulty level)

Hard

Very Hard Harder

“Same as Play

Buy-In Price1 Coin ContinueSettings of the continue play fee

2 Coins Continue

3 Coins Continue

1 to 4 Coins Settings of the play fee

1 to 6 Credits *1 coin, 1 credit

1 to 4 coins Settings of the play fee (Coin slot A)

(Note 2) 1 to 6 credits *1 coin, 1 credit

Coin-B1 to 4 coinsSettings of the play fee (Coin slot B)

(Note 2) 1 to 6 credits *1 coin, 1 credit

(See notes | through 3 on next page.)

Page 10

a

Configuration Setting Notes

Note 1: The specifications for the North American market.
Note 2: The specifications for other than the North American market.

Select “EXIT” and press the trigger of the 1P or 2P gun and the confirmation screen appears. When you want to change the settings, select “YES” (pull 1P gun trigger) and press the 1P or 2P start button. When you want to cancel the setting, select “NO" (pull the 2P gun trigger) and press the start button of 1P or 2P. The settings return to the previous condition. After pressing the start button, the screen returns to the menu screen.

Moving Test

This is to check the vibration mechanism of the guns. Both “Manual” and “Automatic” are provided. Select one of them by pressing the start button of 1P or 2P.

“PULL 1P AND 2P TRIGGER” (Manual) The vibration mechanism of the gun is functioning while pulling the trigger.

“AGING MODE” (Automatic) Pull the trigger of the 2P gun and turn on the display. The screen terminates the test mode and begins repeating 5 seconds of vibration and 2 seconds of no vibration alternately in the demonstration screen. The lamps of the 1P and 2P start buttons also repeat 5 seconds of lighting and 2 seconds off accordingly. To quit this mode, pull the trigger of the 1P gun and change the display to “OFF.”

“EXIT” Select “EXIT” and press the trigger of the 1P or 2P gun. The confirmation screen appears. When you want to change the settings, select “YES” (pull the 1P gun trigger) and press the 1P or 2P start button. When you want to cancel the setting, select “NO" (pull the 2P gun trigger) and press the start button of 1P or 2P and the settings return to the previous condition. After pressing the start button, the screen returns to the menu screen.

Page 11

Gun Sight Test

This mode is to adjust the position of a gunlayer. During the actual game, the gunlayer is not displayed. This adjustment is required when the bullet mark deviates from the targeted point.

Point 1

n the first menu screen, point the IP or 2P gun at the screen. The message “NOW SIGHT POSITION” will appear in the center of the screen. The 1P gun will produce a red movable dot. The 2P gun will produce a blue dot on the screen. Use these dots for sight positioning.

9 confirm whether or not any adjustment of the gun sight is required, pull the trigger so that the bullet mark appears and press the shotgun button so that the bullet mark disappears.

he numbers displayed on left and right of the screen show the coordinate that has been targeted.

One press of the test switch will change to the IP gun. Two presses of the test switch will change to the 2P gun. Three presses of the test switch will change to the display shown below:

GUN SIGHT TEST

<NOW SIGHT POSITION>

PAINT -> TRIGGER SW. CLEAR -> SHOTGUN SW

MODE SELECT -> TEST SW. EXIT-> 1P OR 2P START

The 1P gun side will display the message "PLAYER 1 OFFSET” at the center of the screen. The 2P gun side will display the message "PLAYER 2 OFFSET” at the center, respectively.

Pull the trigger while sighting on the center of the screen. During this sighting, the gun end should point to the center of the screen (see next page):

Page 12

Mirror-reflected Picture

Point 2

Aim at the center of the flashing green square and pull the trigger. Then shoot all 12 square targets.

After you shoot all 12 targets successfully, the “IP NEW DATA SAVE@" message will appear just below the screen center. Pull the trigger again. The new data is stored. To return to the green flashing square screen, pull the shotgun button.

GUN SIGHT TEST

im)

PLAYER 1 OFFSET

SET -> TRIGGER SW CANCEL -> SHOTGUN SW

MODE SELECT -> TEST SW EXIT -> 1P OR 2P START

To return to the menu screen, press the start buttons IP or 2P.

Page 13

a

Factory Setting

This mode is to return all the settings, except the positional setting of gunlayer, to the default values (set conditions at delivery).

Pull the trigger of the 1P gun to select "YES” or pull the trigger of the 2P gun to select “NO.” Confirm this setting by pressing the start button of 1P or 2P.

The SOUND VOLUME figure of "SOUND TEST" : 30.

Factory settings are marked by the asterisks (*) in “CONFIGURATION.”

Exit

Select this mode to return to the game screen after terminating the test mode. After selecting “EXIT,” pull the trigger of the 1P gun to select “YES” (quit test mode), or pull the trigger of the 2P gun to select "NO" (cancel quit of test mode). Press the start button of 1P or 2P to confirm this selection.

ATTENTION

Each day the Operator should check that ALL warning labels are legible and affixed to this equipment in their proper locations.

Page 14

Gun ASSEMBLY

S/A: Gun Assembly B Relay PC! 79200352A Part No. K91X0473A

Page 15

FRONT REPLACEMENT Parts

Page 16

eal Attention: Please note the new size of the mirror (Sea. 3): 27.88" x 28.38” x .125” Front Replacement Parts List

24” Fluorescent Lamp F20T12CW 056-009-000

2aMarquis StyreneB309-509-0001
2bGlass Header27.88" x 7.75" x .187"309-500-0001
3Mirror17.88" x 28.38" x 0.25"309-501-0001
4Viewing GlassB309-502-0001
5Holster Vacuum Form (Red)anB309-504-0021
6Holster Vacuum Form (Blue)]B309-504-001J
7a, 8aHolster Front(black plastic)B309-51 1-0042 perside
7b, 8bHolster Left Side (black plastic)B309-51 1-0011 per side
7c, 8cHolster Right Side (black plastic)|B309-51 1-0021 per side
7d, 8dHolster Front Plate (black metal)309-115-0001 per side
7e, 8eFront (black plastic)B309-511-0031
9Stirrup EyeB309-111-0001
10aGun Plate Cable (inside cabinet)B309-106-OPA1
106Strain Relief Gun Cable (inside cabinet)0042-035-0001
aMat Stopper309-113-0001
12Rubber Mat309-511-0031
130Rubber Mat (right side)309-511-0021
136Rubber Mot (left side)TB309-511-0011
14Mat stopperB309-114-OPA2
15L-Shaped RubberB309-512-0002
16Decal: Cabinet (right side)B309-507-0001
7Decal: Cabinet (left side)309-506-0001
18Red Start Button with lightB309-025-0001

Blue Start Button with light B309-026-000

Control Panel Overlay B309-505-000

Page 17

REAR REPLACEMENT PARTS

Seq.DescriptionPart No.|Qty.
127" Monitor Hantarex Polo Model056-067-0001
2Main PC Board AssyK11T0777A1
3S/A Power Supply BoardB309-01 4-0001
3aPower Supply Switching 11-150XT0052-429-0001
3bRectifier Bridge 35 amp 600v0052-366-1003
3cCapacitor 20,000MF 30v0052-429-0004
3dTransformer0053-098-0001
Page 18

LED Box ASSEMBLY

Description Part No. Qty.

LED Box£30116431
LED PC Board AssyK91X04642
Filter CoverF90035102
Plastic Spacer 4x 8x 12F90009234

Flange Nut M4 4

Page 19

taana m7 BRszecsg GUN SENSOR Siaes

Page 20

RE - MAIN PCB

EAABINESTTEICICIT) Y comecion RELAY PCB EE a0

GUN SENSOR

Page 21

SAVE CHILENS ll THE CY WICH ISATIACKED MIOTERS//

2-PLAYER SIMULTANEOUS(COOPERATIVE)PLAY &

BUY-IN POSSIBLE!!

= POLICE BADGE POINTS INCREASE. FST CIRTRDG pein

ThiITO GTAITO CORP. 1993

Page 22

ThITO TAITO AMERICA CORPORATION 390 Holbrook Drive Wheeling, IL 60090 Telephone: (708) 520-9280 Fax: (708) 520-1309