Liberator TM-209 1st Printing
Liberator (version 2) (Atari, 1982) · Technical Manual · 76 pages · 53 sections · original scan

This page is a drawing, shown as the original scan.
If reading through this manual does not lead to solving a certain maintenance prob-
lem, call TELEHELP® at the Atari Customer Service office in your geographical
area, as shown below.
FIBERATOR}
Operation, Maintenance, and Service Manual
Complete with Illustrated Parts Lists
Liberator™
© 1982 by Atari, Inc. All rights reserved. No part of this publication may be reproduced by any mechanicai, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher. The Liberator™ game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the U.S. Copyright Act of 1976. This Act provides for increased penalties for violating federal copyright laws. Courts can impound infringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles. In addition, the Act provides for payment of statutory damages of up to $50,000 in certain cases. Infringers may also have to pay costs and attorneys’ fees, fines up to $25,000, and face an imprisonment of up to one year. Atari will aggressively enforce its copyrights against any infringers. We will use all legal means to immediately halt any manufacture, distribution, or operation of a copy of video games made by us. Anyone who purchases such copies risks forfeiting such a game.
Published by: ATARI, INC. 790 Sycamore Drive P.O. Box 906 Milpitas, California 95035
Lithographed in the U.S.A. 10L
Liberator™
Notice Regarding Non-ATARI Parts
Use of non-ATARI parts or modifications of your ATARI® game circuitry may adversely affect the safety of your game, and may cause injury to you and your players.
You may void the game warranty (printed on the inside back cover of this manual) if you do any of the following: @ substitute non-ATARI parts in the game @ modify or alter any circuits in the game by using kits or parts not supplied by Atari.
INTERFERENC
to licensed communications services is not permitted by the Federal Communications Commission (FCC).
If you suspect interference from an ATARI® game at your location, check the foliowing: @ all green ground wires in the game are properly Connected as shown in the the game wiring diagram @ the power cord is properly plugged into a grounded 3-wire outlet. If you are unable to solve the interference problem, please contact ATARI Customer Service. See the inside front cover for service in your area.
Liberator™
Table of Contents
Set-Up Procedures A. New Features 0.0.0.0 cece cece ccc tence ene e ees B. Inspecting the Game C. Space and Power Requirements .
- Installation Requirements . .
- Selecting the Voltage Plug D. Locating the Switches ...
- On/Off Switch ......
- Utility Panel Switches .
- Option Switches ..... Setting the Option Switches .. Performing the Initial Self-Test . Game Play.............
- Demonstration Mode .
- Attract Mode ...
- Play Mode.... 4. 5. omm
High-Score Mode . . Hints for Game Play... 0.0... eee ee cece eee
Self-Test Procedure A. Comments on Troubleshooting .......... 0... 0c e eee eee eee B. Performing the Self-Test .......... 00... c cece ee ee eae
Maintenance, Repair, and Parts Cabinet-Mounted Assemblies . Control Panel .............. Fluorescent Tube and Speaker . Video Display .......... Utility Panel . . Coin Door ........ Printed-Circuit Boards on . Power Supply Assembly .........0 0.0000 c ccc c eee eee eee ees Glossary of Terms Glossary Begins on Page ....... 00.006 cece cece eee ees ToONMMIODyY SRSOGOONDEEELEDOHOH
Figure 1-1 Figure 1-2 Figure 1-3 Figure 2-1
Figure 2-2 Figure 2-3 Figure 2-4 Figure 25
Figure 3-1 Figure 3-2 Figure 3-3 Figure 3-4
Figure 3-5 Figure 3-6 Figure 3-7
Figure 3-8
Figure 3-9 Figure 3-10 Figure 3-11 Figure 3-12
Figure 3-13 Figure 3-14
Table 1-1 Table 1-2 Table 1-3 Table 1-4
Table 15 Table 2-1 Table 2-2 Table 2-3 Liberator™
List of Illustrations
Game Overview ...... 66. cece cece teen e tees 1-2 Location of Game Switches . 1-4 Self-Test Display............ . WW Self-Test Screen 1—Test Passes .........-. 0.0.0 e cece eee 22 Self-Test Screen 1—Test Fails ............ 0.00. cece eee eee 23 Self-Test Screen2....... 24 Self-Test Screen 3.. 2-4 Self-Test Screen 4.. 24
INustrated Parts Lists
Cabinet-Mounted Assemblies, Upright Cabinet .............. 3-2 Cabinet-Mounted Assemblies, Ireland-Built Cabinet - 34 Control Panel .......... - 36 Control Panel Assembly 37
Midi Trak-Ball™ Assembly ..............0...000c. cee eee ee 3-10 Fluorescent Tube and Speaker, Upright Cabinet.............. 3-14 Fluorescent Tube, Speaker, and Attraction Panel, {reland-Built Cabinet 0... 2.26... ccc cee Video Display, Upright Cabinet . . Video Display, Ireland-Built Cabine Utility Panel Assembly... 2. eee eee ee 3-21 Vertically Mounted Coin Door .... . 322 Removing the Printed-Circuit Boards ......... . 325 Liberator™ Game Printed-Circuit Board Assembly ........... 3-26
Regulator/Audio II Printed-Circuit Board Assembly . F Power Supply Assembly ........... 00.00.00 e eee eee eee
Switch Settings for Price Options ......................0 88 15 Switch Settings for Play Options . 16 Self-Test Procedure ........ : . 18 Liberator™ Game Play ..........0.-002e cc ee eee eee eens 1-11
Liberator™ Scoring Failing RAM Location ... Failing Bit Map RAM Location 7 . Failing ROM Location ........... 000s cece eee eect e eee eee 2-3
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Set-Up Procedures
“How to Use
this Manual
This manual, written for game operators and service technicians, describes the Liberator™ game. The manual contains information about the Upright and /reland-built Liberator cabinets. Whenever information is unique to the Upright cabinet, this symbol appears:
Whenever information is unique to the freland-
built cabinet, this symbol appears: *
Chapter 1 describes new features, game setup, settings of option switches, self-test procedures, and game play. Chapter 2 contains self-test procedures. Chapter 3 details maintenance, repair, and parts information. A glossary of terms is in the back of this manual for your convenience. In addition, schematic diagrams of the game circuitry are included with this manual. Figures 1-1 and 3-1 illustrate the game cabinet. Italicized lettering on these figures refers you to other places in the manual for information about specific cabinet parts.
Chapter
Set-Up Procedures
FLUORESCENT TUBE AND SPEAKER See Figure 3-6 or 3-7 ATTRACTION PANEL See Figures 3-1, or 3-2, and 3-7
- VIDEO DISPLAY See Figure 38
CONTROL PANEL See Figures 3-3 & 3-4
aH
MIDI TRAK-BALL See Figure 3-5
COIN DOOR See Figure 3-10
UTILITY PANEL See Figure 3-9
% POWER SUPPLY. See Figure 3-14
As warnine Ay SHOCK HAZARD This game should only be connected toa grounded 3-wire outlet. If you have only a 2-wire outlet, we recommend you hire a licensed electrician to install a grounded outlet. You may receive an electric shock if the game is not properly grounded!
Figure 1-1 Liberator™
x item with a serial number label
GAME IDENTIFICATION LABEL
ACCESS PANEL
SERIAL NUMBER © LABEL
SERIAL NUMBER LABEL
= * GAME PCB See Figures 3-11 & 3-12
SERIAL NUMBER LABEL
% REGULATOR! AUDIO II PCB See Figures 3-11 & 3-13
SERIAL NUMBER POWER ON/OFF SWITCH LABEL
Game Overview
Liberator™
A. New Features
The Liberator™ game has four new features. Even if you are familiar with ATARI®? games, you should note these important differences:
- Shielded Game Speakers. These 8-ohm, 6-ounce, high-fidelity speakers provide exceptional audio. The speaker magnets are shielded.
- Midi Trak-Ball™ The popular Trak-Ball”™ assembly has been enlarged and simplified. The housing for this control is a molded plastic frame with two parts. Smooth action of the Midi Trak-Ball improves player accuracy.
- Grey Tinted Glass. This new shade of tempered glass used in the display shield enhances video colors.
- Molded Coin Box. This game has a sleek, onepiece molded coin box with handles on either end for easy carrying. New features and all other major parts of the game are illustrated in Figure 1-1. Throughout this manual, wherever one of these new features is mentioned,
you will see this symbol: a
B. Inspecting the Game
Please inspect your game carefully to ensure that it was delivered to you in good condition.
- Examine the exterior of the game cabinet for dents, chips, or broken parts.
- Remove the screws that were used as extra security to seal the rear access panel. Unlock and open this panel and the coin door; inspect the interior of the game as follows: a. Ensure that all plug-in connectors (on the game harness) are firmly plugged in. Replug any connectors found unplugged. Do not force connectors together. The connectors are keyed so they only fit in the proper orientation. A reversed edge connector may damage a PCB and will void your warranty. b. Ensure that all plug-in integrated circuits on the PCB are firmly plugged into their sockets. ‘Set-Up Procedures
c. Remove the tie-wrap that secures the coiled power cord inside the cabinet. Inspect the power cord for any cuts or dents in the insulation. Repair or replace it as required. Place the square btack plastic strain-relief plate in the wood slot at the bottom of the rear panel opening. d. Note the game serial number printed on a label on the back of the cabinet. Verify that the same serial number is also on the Liberator game PCB, Regulator/Audio II PCB, power supply, and video display. See Figure 1-1 tor locations of the serial-numbered components. Please mention this serial number whenever you call your distributor for service. e. Inspect major subassemblies, such as the power supply, control panel, and video display. Make sure that they are mounted securely,
= WARNING dy To avoid electrical shock, do not touch internal parts of the display with your hands or with metal objects held in your hands!
C. Space and Power Requirements
- Installation Requirements
Power 200 W Temperature Oto +38°C (+32 to + 100°F) Humidity Not over 95% relative Upright Cabinet 62 x 78 cm (25% x 30% in.) 184 cm (72 ¥2 in.) Ireland-Built Cabinet Space Required 60 x 68 cm (24 x 27 in.) Game Height 170 cm (67 in.) Space Required Game Height
- Selecting the Voltage Plug The power supply used in this game operates on the line voltage of almost any country in the world. The power supply comes with either one, two, or three separate voltage-selection plugs. Plug voltages and wire colors are 100 VAC (violei wire color), 120 VAC (yellow wire color), 220 VAC (blue wire color), and 240 VAC (brown wire color).
1-3
Set-Up Procedures
Before plugging in your game, check your line voltage. Next, check the wire color on the voltage selection plug that is plugged into your power supply. Make sure the voltage selection plug is correct for the voltage of your location (see Figure 3-14).
D. Locating the Switches
- On/Off Switch
The on/off switch is located on the back of the cabinet on the lower left side (see Figure 1-2). Liberator™
- Utility Panel Switches The utility panel includes the volume control, selftest switch, coin counter(s), and auxiliary coin switch (used to credit the game without activating the coin counter). The utility panel is located inside the upper coin door (see Figure 1-2).
- Option Switches Option switches are located on the game PCB (see Figure 1-2). a. Game-price options are at PCB location A4. b. Game-play options are at PCB location D4.
c. een counter options are at PCB location
12.
UTILITY PANEL See Figure 3-9
POWER ON/OFF SWITCH SWITCH AT A4 (Game price) SWITCH AT D4 (Game play) SWITCH AT T12 (Coin Counter)
Figure 1-2 Location of Game Switches
1-4
Liberator™
E. Setting the Option Switches
Settings of the game option switches are explained in Tables 1-1 and 1-2. Options preset at the factory are shown by the < symbols. However, you may change the settings according to your individual needs. To verify option switch settings, first toggle the on/off switch to the off position and then to the on position. Next, set the self-test switch to the on position, and verify the settings on the self-test screen. Then set the self-test switch to the off position. Table 1-1 contains the switch settings for options relating to game price, coin mechanism multipliers, and bonus play. The switches are on the game PCB at location A4. The multipliers (toggles 4-6) determine the value of the coin mechanisms to the game’s logic. A coin mechanism is a device on the inside of the coin Set-Up Procedures
door that inspects the coin to determine if the correct coin has been inserted. After this inspection, the mechanism either accepts or rejects the coin. The coin door has two mechanisms. The basic unit of measurement is a coin worth $.25 or 1 DM, which equals a multiplier of x1. For example, if you have a 2 DM/1 DM coin door, you may want to set the left multiplier at x2 and the right multiplier at x1. You may offer bonus play for certain combinations of coins inserted. For example, with the game set at $.25 per play, players who deposit four successive $.25 coins before pressing the start switch can receive a bonus play. The bonus feature encourages players to insert more money than just the minimum $.25 required for one game. Switch 1 of the 4-toggle switch at PCB location 112 should be set in the on position. For the !relanabuilt cabinet, this ensures that a coin inserted in either coin mechanism will be counted. Switches 2, 3, and 4 are not used.
Table 1-1 Switch Settings for Price Options
Settings of 8-Toggle Switch on Liberator PCB (at A4) 8 7 6 5 4 3 2 Option
Ott Ott
On Off
Off Oft Off On
On On
On On
Off On
| Off | Oft | off |
Off On Off Off Ott On
| On | On | Otf |
On Ott On
| Off | On | On |
| On | On | On |
Free play 1 coin tor 2 credits 1 coin for 1 credit < 2 coins for 1 credit
Right coin mechanism x 1 < Right coin mechanism x 4 Right coin mechanism x 5 Right coin mechanism x 6
Left coin mechanism x 4 <4 Left coin mechanism x 2 No bonus coins < For every 4 coins inserted, logic adds 1 more coin
For every 4 coins inserted, iogic adds 2 more coins For every 5 coins inserted, logic adds 1 more coin For every 3 coins inserted, logic adds 1 mote coin No bonus coins No bonus coins
< Manufacturer's recommended settings
Set-Up Procedures Liberator™
Table 1-2 contains the switch settings for options relating to number of ships per game, bonus levels, and game difficulty. The switches are on the game PCB at location D4.
Table 1-2 Switch Settings for Play Options
Settings of 8-Toggle Switch on Liberator PCB (at D4)
| 8 | 7 | 6 | 5 | 4 | 3 | 2 |
1 Option
| Off | Off | 4 ships per game < |
| On | Off | 5 ships per game |
| Off | On | 6 ships per game |
| On | On | 8 ships per game |
3 3 ,
| Off | Off | g | g | Bonus ship every 15,000 points |
| On | Off | 3 | s | Bonus ship every 20,000 points < |
| Off | On | 4 | z | Bonus ship every 25,000 points |
| On | On | Bonus ship every 30,000 points | ||
| On | Off | Easy game play | ||
| Off | Off | Normal game play < | ||
| Off | On | Hard game play |
4 Manufacturer's recommended settings
1-6
Liberator™
F. Performing the Initial Self-Test
This game will test itself and provide data to show that the game’s circuitry and controls are operating properly. The data is provided on the video display and speaker. No additional equipment is necessary. Wait at least 10 seconds after playing a game before switching to the Self-Test Mode. Otherwise, you may erase the top three scores in the high-score table or distort the statistics. All credits will be cancelled when you switch to self-test. Set-Up Procedures
Refer to Figure 1-2 for the location of the self-test switch and option switches. Set the self-test switch to the on position (see Figure 1-3) to see the Self- Test Display in the Self-Test Mode. To exit the Self- Test Mode, set the self-test switch to the off position. The complete self-test procedure is explained in Chapter 2, B. Self-Test Procedure.
We suggest you perform the self-test procedure when you first Set up the game, any time you collect money from the game, when you Change game options, or when you suspect game failure.
TOGGLE 1
SWITCH AT A4
(Game options)
TOGGLE 8
POCOOC1 a Oo
0DOO00 o
SWITCH AT D4
(Game pricing)
TYPE OF CABINET
MIDI TRAK-BALL™
Figure 1-3 Self-Test Display
1-7
Set-Up Procedures Liberator™
Table 1-3 Self-Test Procedure
Instruction Test Passes
- Switch the self-test switch to the on position.”
- Press the control panel pushbuttons and the left and right coin switches. Roll the Midi Trak-Ball™.
- Press the auxiliary coin switch on the utility panel.
- Press the auxiliary coin switch.
- Press the auxiliary coin switch. The screen goes blank for a few seconds while a continuous low-to-high tone sounds. This tone means the VBLANK and timing circuits are working correctly. If there is no tone, refer to Chapter 2, Self-Test Procedure.
The self-test display appears. RAMs, ROMs, and the bit map are tested. If the screen is different from the self-test display, or if there are sounds, refer to Chapter 2, Self-Test Procedure.
As you press the pushbuttons or switches, you will hear a tone, the screen will change color, and the corresponding 0 will change to 1. Pressing any pushbutton or switch will change the color of the screen and will change the appearance of the planet alternately from Earth to Jupiter. The (Midi Trak-Ball) cursor moves freely. If the test fails, refer to Chapter 2, Self-Test Procedure.
The screen displays the game bookkeeping statistics as follows:
- Average of the total game scores
- Average cumulative game time
- Number of one-player games played » Number of two-player games played If the test fails, refer to Chapter 2, Self-Test Procedure.
The screen displays the following color bar pattern:
- Three shades of blue (light to dark)
- Seven shades of green (light to dark) Seven shades of red (light to dark)
- Alternate white and black squares If the test fails, refer to Chapter 2, Self-Test Procedure.
A grid pattern framed in red and green appears on the screen. The corners of the green frame must be visible at all times; the corners of the red frame may or may not be visible. The corners of the display should cut across the blue boxes located in the corners of the convergence display between the red and green frames. If the test fails, refer to Chapter 2, Self Test Procedure, Screen 4.
“All credits are cancelled when you switch to self-test.
Liberator™
G. Game Play
Liberator™ is a one- or two-player game with a color raster-scan video display. The game action takes place in various star systems in outer space. There are missile bases on planets and enemy spaceships that the player tries to destroy. The object of the game is to find and destroy the enemy missile bases. The player controls a fleet of four spaceships, each located in a corner of the screen. Each ship has a weapon that shoots a laser beam. A fleet of four spaceships may have as many as 12 shots on the screen at one time. The player uses the Midi
Trak-Ball™ to control a cursor (@ mark) that appears
on the screen. The @ marks where a laser shot is to
explode. When the player presses the FIRE button, a laser beam is launched from the nearest spaceship to the @. When the beam reaches the @ there is an explosion. Any object within the explosion is destroyed. Nearby objects may also be damaged. To protect his spaceship, a player may use the SHIELD button. Each ship has four shields at the beginning of a level of play. A hit to a shield destroys that shield and the corresponding shields that protect other spaceships. When starting a game, a player may select an advanced level of play. When a game ends, the message FOR ADVANCED GAME HOLD FIRE AND PRESS START appears. The player presses FIRE to select the level of game play. Levels increase by three, up to Level 22. The player starts the game by Pushing a start button. \f a player selects and successfully completes a higher level of game play, he is awarded bonus points. There are 30,000 bonus points and a bonus spaceship (for a maximum of eight regular and bonus ships per player) awarded for completion of each star system. There are three levels of game play within each star system. For example, if a player selects and completes Level 22, he is awarded 210,000 bonus points and has eight ships. Set-Up Procedures
Liberator™ has five possible modes of operation: Demonstration, Attract, Play, High-Score, and Self- Test. Self-Test is a special mode for checking the game switches and computer functions. You may switch to the Self-Test Mode during any mode. All credits will be cancelled. Wait at least ten seconds after a game has been played before switching to Self-Test or switching off power; otherwise, you may erase the highscore table.
- Demonstration Mode
To switch to the Demonstration Mode, simultaneously press any start button and the auxiliary coin switch (located inside the upper coin door). In this mode your spaceships cannot be destroyed by the enemy. Thus, you can see all the star systems and obstacles in the game. To exit this mode, press the auxiliary coin switch.
- Attract Mode
The Attract Mode begins when power is applied to the game, after a Play or High-Score Mode, or after Self-Test. The Attract Mode ends when a credit is inserted and a start button is pressed, or when the Self-Test Mode begins. The screen displays one of five possible pictures in the Attract Mode. The first picture takes place in hyperspace and a message to the player reads: THE GALAXY HAS BEEN INVADED BY THE EVIL MALAGLON ARMY. COMMANDER CHAMPION OF THE ATARI FORCE HAS CHOSEN YOU TO BECOME THE LIBERATOR. THE PEOPLE OF THE UNIVERSE ARE DEPENDING ON YOU TO FREE THEM FROM THEIR EVIL MASTERS. In the second picture, the words JO/N THE ATARI FORCE IN: appear at the top of the screen. There is a rotating Earth-like planet in the center of the screen. LIBERATOR appears in an orbit around the planet. © ATARI 1982 appears at the bottom of the screen.
1-9
Set-Up Procedures
The third picture simulates game play. Two messages appear on the screen— YOUR MISSION: SHOOT RED FLASHING MISSILE BASES ON PLANET and PROTECT SHIPS FROM ONCOMING MISSILES. The number of remaining enemy bases appears at the bottom of the screen. In the fourth picture, a planet rotates. The messages ONE OR TWO PLAYERS and PRESS START appear on the screen if the correct number of credits have been inserted. The High-Score Table appears in the fifth picture. There is a list of the ten highest scores. Opposite each score are the initials of the player who achieved that score. All pictures in the attract mode display information about the number of coins required to credit the game, and, if applicable, the number of credits shows at the bottom of the screen. The Attract Mode ends when a credit(s) is inserted and the 1- or 2-player button(s) is pressed.
- Play Mode The Play Mode begins when the correct amount of credit is inserted and a start button is pressed. Game play begins in hyperspace of the first star system. Enemy spaceships try to ram and destroy the player’s spaceships. The player must destroy
1-10 Liberator™
these enemy ships using the FIRE button. There is no shield in hyperspace. When the enemy spaceships on the screen are destroyed, LEVEL 7 and a revolving Earth-like planet appear on the screen. There are four enemy missile bases on the planet. The base launches missiles toward the player's spaceships. The missiles travel in a curved line. The Player must destroy the missiles before they destroy his spaceships. When the missile bases cross an imaginary vertical line in the center of the planet, the bases become satellites. The satellite launches a missile that travels in a straight line toward the player's spaceships. When all bases are destroyed, the player’s remaining spaceships fly to the planet. Bonus points appear at the top of the screen when the ships land on the planet. There are 100 bonus points for each remaining ship. In Level 2 there are 200 bonus points per ship; Level 3 has 300 points; and so on. After Level 7, the bonus is 800 points for each remaining ship. The screen also displays the points at which the next bonus ship will be awarded. The planets for Levels 2 and 3 contain killer saucers in addition to the missile bases. The saucer flies in space for a period of time and then stops. It emits a sound and begins to increase in size. Then it fires a death ray that cannot be stopped. FIRE and SHIELD offer no protection. The ray destroys the player’s ship. The player must destroy the saucer before it increases in size; otherwise, the death ray will destroy his ship. Game play in the second star system starts in hyperspace with enemy spaceships trying to ram and destroy the player's spaceships. After successfully destroying the enemy ships, Level 4 is displayed with a revolving Earth-like planet. The player has to destroy six missile bases on the revolving planet. Missile bases fire MIRVs, which explode into four smaller missiles when hit. In this system, there are two more planets (Levels 5 and 6) that have killer saucers and missile bases that turn into satellites. Game play progresses through many star systems. Play in each system begins with enemy spaceships trying to ram the player’s spaceships. Next, there are three levels (each with a different planet) within a system. In each new level, the color of the planet changes and the direction of planet rotation reverses. The player score and number of space ships appear at the top of the screen, and the number of missile bases appears at the bottom of the screen. As bases are destroyed, the number decreases to show the remaining bases. Game play proceeds as before, but in each new star system there are more missile bases and different obstacles. (See Table 1-4 for a list of obstacles in each star system.)
Liberator™
Fireballs appear in the third star system. Fireballs are red and yellow circular shapes that appear to be burning. When shot with the laser beam, the fireball slows down. It takes four shots to destroy a fireball. In the ninth star system a master base appears. It is a white, pulsating base. The base is smart—it can sense when a laser beam is aimed at it. The masier base can decrease or increase the speed of the planet or change the direction of planet rotation to avoid being destroyed!
Table 1-4 Liberator™ Game Play
‘STAR PLANET SYSTEM 1 Earth-like
2 Earth-like
3 Jupiter-like
4 Jupitersike
5 Earth-like
6 Jupiter-like
7 Earth-like
8 Jupiter-like
9 Earth-like
10°* Jupiter-like OBSTACLE*
4-5 bases Bases become satellites Killer saucer 6-7 bases Bases become satellites Killer saucer MIRVs, 8-9 bases Bases become fireballs Killer saucer 10-11 bases MIRVs, Fireballs Killer saucer 12-13 bases Faster rotation of planet Satellites Killer saucer 14-15 missile bases Faster rotation of planet Fireballs 16 bases MIRVs Satellites 16 bases Faster rotation of planet MIRVs Fireballs 16 bases Master base MIRVs Satellites 16 bases Master base MIRVs, Fireballs
*Each star system has eneny spaceships, missile bases, and missiles. **After Star System 10, fireballs become starballs. Set-Up Procedures
In the eleventh star system, starballs appear. (After the tenth star system, fireballs become starbails.) Starballs are red circular shapes. A starball slows down when it is shot by a laser beam, bui speeds up after the hit. It takes four shots to destroy a starball. After the fourteenth star system, there are one more MIRV and one more starball for each new star system. (See Table 1-5 for a list of targets and their point values.)
Table 1-5 Liberator™ Scoring
TARGET POINT VALUE
Enemy spaceship 50 Missile base 100 Satellite 20 Killer saucer 150 MIRV 10 Fireball 20 Starball 20
- High-Score Mode The High-Score Mode begins when a player has earned one of the ten highest scores. The player has one minute to record his initials. A player spins the Midi Trak-Ball™ to locate his initial. He presses FIRE to put his initial into the high-score table. To reset the high-score table, power the game off and then on, or switch the self-test switch on and off. However, this does not erase the top three scores.
- Hints for Game Play
- Destroy the enemy missile bases on the planet first, before they launch their missiles! ¢ Destroy the killer saucer as soon as it begins to grow in size and make a sound.
- Plan your shot so it explodes in front of a moving target. © Shoot fireballs as soon as possible to slow them down,
- For fast planets, place shots in a long vertical line directly over the planet.
1-11
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Self-Test Procedure
The following self-test procedures should be performed by a qualified electronic technician. This game tests itself when the self-test switch is set to the on position. If there is a failure, the game produces audiovisual aids to help you find the failing portion of the game. The self-test procedure included in Chapter 1 will help you decide if the game is or is not working properly.
Chapter
A. Comments on Troubleshooting
When troubleshooting, first determine the symptom(s) of the failure. After determining the symptom, look over the wiring diagram and determine what assemblies could cause the failure. Could it be caused by the power supply, Regulator/Audio II PCB, or the video display? The next step is to check all harness wires and connectors to the suspected failing assembly. If you find no harness or connector problem, substitute an assembly known to be good for the suspected failing assembly. If the game functions properly, you have successfully isolated the failure. If it doesn’t, repeat the procedure with another assembly. When you have isolated the failing assembly, you must troubleshoot that assembly and make the necessary repairs. If the video display fails, we suggest that a qualified video-display technician perform the troubleshooting and repair. Be sure to refer to The Book—A Guide to Electronic Game Operation and Servicing, published by Atari, Inc., whenever you need help with the techniques, tools, and terminology associated with coinoperated electronic games. To effectively troubleshoot a game PCB, learn as much as you can about the PCB. The diagrams in the Schematic Package (included with the game) show the functions of the circuitry. Again, while troubleshooting the PCB, first determine the symptom of the failure, then locate the suspected area on the schematic diagram. A Glossary of Game PCB Signal Names is included in the Schematic Package. Each signal description states if the signal is generated by hardware or software, where it is generated, where it goes, and what it does. We suggest you use this glossary to become more familiar with the operation of the game PCB.
B. Performing the Self- Test
The following self-test procedures should only be performed by a qualified electronic technician. This game will test itself and provide data to show that the game’s circuitry and controls are operating properly. The data is provided on the video display and speaker. No additional equipment is necessary. To switch to the Self-Test Mode, set the self-test switch, located on the utility panel, to the on posi- Liberator™
tion. Press the auxiliary coin switch, located on the utility panel next to the self-test switch, to progress through tests 1 through 4.
SCREEN 1—Test Passes:
If the test passes, the screen goes blank for a few seconds before displaying the picture below. Upright games should display the message UPRIGHT in the lower right corner of the screen; cocktail games should display COCKTAIL in the same location. You will hear a continuous low-to-high tone while the screen is blank. See Chapter 1, Section F, Performing the Initial Self-Test for a complete description of this picture.
Figure 2-1 Self-Test Screen 1— Test Passes
This procedure does not test the coin door lockout coils and coin counter. If the lockout coils do not function when the game is on, suspect the lockout coil wiring or the + 10-volt power supply. Troubleshoot using the game harness schematics. If the coin counter fails, make sure coin-counter switch 1 at T12 on the game PCB is correctly set in the on position. If the coin counter still fails, suspect latch T11 on the game PCB. Refer to the game schematics to troubleshoot any further problems with the coin counter.
Liberator™
SCREEN 1—Test Fails: RAM failure is indicated by a blank or “garbage”-filled screen and a repeating series of eight tones. A low tone indicates a good RAM; a high tone indicates a failed RAM. The tone number and matching RAM location are listed in Table 2-1.
Table 2-1 Failing RAM Location
Failed
Tone RAM Location
Number on Game PCB
Ist J10 2nd M10 3rd $10 4th F10
Sth L10
6th P10 7th T10 8th E10
err MAP ERROR BLT MAP ERROR BLT MAP ERROR BIT MAP BIT MAI BIT BIT BI B.
[J B RROR BI IAP ERROR BIT MAP ERROR BIT MAP ERROR
Figure 2:2 Self-Test Screen 1— Test Fails
BIT MAP RAM failure is indicated by BIT MAP ER- ROR dispiayed on the top center of the screen plus a repeating series of four tones (see Figure 2-2). A low tone indicates a good RAM; a high tone indicates a failed RAM. Bitmap tone numbers with corresponding RAM locations are listed in Table 2-2. Troubleshooting
Table 2-2 Failing Bit Map RAM Location
Failed Bit Map
Ist K10 2nd N10 3rd R10 4th H10
ROM failure is indicated by BAD message and the ROM checksum displayed opposite the number of the failed ROM. (Ignore the checksum.) The failed ROM and its location are listed in Table 2-3.
Table 2-3 Failing ROM Location
Failed
Screen ROM Location
Display on Game PCB
6° 1 5* RIS1 4° PI 3 Nt 2 uM1 1 K1 0 J
*This ROM contains the Self-Test program. If this ROM fails, the screen will be blank or will display “garbage.”
SWITCH failure is indicated by the corresponding 0 not changing to a 7 on the screen when the switch is pressed. Troubleshoot using the information in Chapter 3, Section B, and the game schematics.
SOUND failure is indicated by the absence of any sound when any of the control panel pushbuttons or game switches are pressed. Inspect the volume controls on the utility panel, or troubleshoot using the game schematics.
MIDI TRAK-BALL™ failure is indicated by no movement or jerky movement of the cursor when the Midi Trak-Ball is rolled. If the cursor fails to move, or if movement is reversed or jerky, inspect the Midi Trak-Ball connections (see Chapter 3, Section B).
Troubleshooting
PLANET failure is indicated in several ways: if the planet fails to appear, fails to rotate, or if the missile bases fail to flash, refer to the schematics. elf the Earth-like planet fails to appear, suspect ROMs MINB or T8. elf the Jupiter-like planet fails to appear, suspect ROMs P8 or R/S8. elf either planet has horizontal bars of color, suspect ROM S7. elf either planet has vertically jumping blocks of color, suspect ROM T7. *lf horizontal segments of either planet are uneven during rotation, suspect ROMs N6 and P6. To see the remaining self-test screens (2, 3, and 4), press the auxiliary coin switch on the utility panel to advance to each screen.
SCREEN 2:
EAROM or CUSTOM 1/0 CHIP failure is indicated by CLEARING ENTIRE EAROM message in the top center of the screen (see Figure 2-3). If the program confirms a failed ROM after clearing, EAROM BAD message appears in the top center of the screen. If replacing the EAROM does not correct the failure, refer to the schematics. To erase average game score and time, press both FIRE and 1-player start pushbuttons at the same time. Release the pushbuttons. Wait until the purple message CLEARING BOOKKEEPING DATA disappears before continuing with other tests. To erase the entire EAROM, press ail four player pushbuttons at the same time. Release the pushbuttons. Wait until the purple message CLEARING EN- TIRE EAROM disappears before continuing with other tests.
AVERAGE GAME TIME OO
AVERAGE GAME Score oo
ONE PLAYER GAMES:
TWO PLAYER GAMES: ara)
Figure 2-3 Self-Test Screen 2 Liberator™
SCREEN 3:
This screen shows the intensities of red, green, and blue (see Figure 2-4). Refer to the color-raster display manual for the next two adjustments. Adjust the levels of each color so that the darkest intensity is just slightly visible from black. Use this pattern for tracking adjustments.
Figure 2-4 Self-Test Screen 3
SCREEN 4: A grid pattern framed in red and green appears on the screen (see Figure 2-5). The comers of the green frame must be visible at all times; the corners of the ted frame may or may not be visible. The corners of the display should cut across the blue boxes located in the corners of the convergence display between the red and green frames (refer to the colorraster display manual).
Figure 2-5 Self-Test Screen 4
Maintenance, Repair, and Parts
This chapter details maintenance and repair information and provides information you need to order parts for your Liberator™ game. Common hardware (screws, nuts, washers, bolts, etc.) has been deleted from most of the parts lists. However, there is a parts list for the hardware needed to mount the printed-circuit boards (PCBs) to the cabinet. The PCB parts \ists are arranged in alphabetical order by component. The components are sorted by reference designator. Other parts lists are arranged alphanumerically by Atari part number. A- prefix numbers come first. Following these are numbers in sequence evaluated up to the hyphen, namely 00thru 99-, then 000598- thru approximately 201000-. When ordering parts, please give the part number, part name, number of this manual, and serial number of your game. This will help to avoid confusion and mistakes in your order. We hope the results wiil be less downtime and more profit from your game. Atari Customer Service numbers are listed inside the front cover of this manual for your convenience.
Chapter
Maintenance, Repair and Parts Liberator™
A. Cabinet-Mounted Assemblies
Fluor. Tube & Speaker Assy. See Figure 36 @) 178034-024 (T-Molding) 03849501 478034-026 (Upper retainer) (T-Motding) 037332.01 (Vent. grille)
038505-01 (Lower retainer) A038477-01 (Cabinet assy)
A038881-07 038496-01 (Lock) (Speaker grille) a 038491.01 (Display shield) 037721-02 (Access panel)
038178-03 Video Display (Cleat) See Figure 3-8 Control Panel Ass y Game PCB Assy. a See Figures 3-3 & ay See Figures 3-11 & 3-12 A038727-01 Midi Trak-Ball™ (Main harn. assy.) See Figure 3-5 A037496-01 (Coin box enclosure)
Coin Door Assy. < Regulator/Audio II See Figure 3-10 gues 31 igure See Figures 3-11 & 3-13
Utility Panel See Figure 3-9
iN
038091-01 (Coin box— not shown) (Power harn. assy.)
78-3201 (Glide)
A037453-03, Power Supply Assy. - See Figure 3-14 03745503, oF Mi Schematics, & Self-Test Label: Power tend lanuals, Schematics, Tes! — A037470-01 (Power cord) ‘see parts list on following page (On/oft switch assy.)
(Caster) 00999201 (On/off switch cover)
Figure 3-1 Cabinet-Mounted Assemblies Upright Cabinet A038476-01 A
Liberator™ Maintenance, Repair and Parts
Cabinet-Mounted Assemblies Upright Cabinet Parts List
Part No. Description A037453-03 Strain-Relief Power Cord (U.S. and Canada) A037455-03 Strain-Relief Power Cord (Australia and New Zealand) A037470-01 Power On/Off Switch/Mounting Plate Assembly A037496.01 Meta! Coin Box Enclosure A037784-03 Strain-Relief Power Cord (United Kingdom, Ireland, Lebanon, Saudi Arabia, India, Hong Kong, Singapore, Egypt, Nigeria, Republic of South Africa, Zimbabwe) A038477-01 Cabinet Assembly (includes glides and PCB retainers, but not the rear access panel) A038727-01 Main Harness Assembly A038729-01 Power Harness Assembly A038881-01 Lock Assembly (for rear access panel) Acceptable substitute is part no. A038881-03
The following six items are the technical information supplements to this game: SP-209 Liberator Schematic Package ST-209-01 Liberator Label with Self-Test Procedure and Option Switch Settings TM-160 Service Manual for 19-inch Electrohome Color Raster-Scan Display (use with part no. 92-049) TM-201 Service Manual for 19-Inch Wells-Gardner Coior Raster-Scan Display (use with part no. 92-055) TM-209 Liberator Operation, Maintenance, and Service Manual TM-220 Service Manual for 19-Inch Matsushita Color Raster-Scan Display (use with part no. 139003-1004) 78-3201 Adjustable Glide 009992-01 On/Off Switch Cover 037332-01 Ventilation Grille 037721-02 Rear Access Panel (does not include lock) 038091-01 Molded Coin Box (not shown) 038178-03 Dual-slotted PCB cleat 038491-01 Video Display Shield 038495-01 Upper Retainer 038496-01 Speaker Grille 038505-01 Lower Retainer 178013-004 Spring Draw Latch (not shown) 178034-024 %4-Inch Black Plastic T-Molding 178034-026 ‘%¢Inch Black Plastic T-Molding 178048.001 2-Inch Rigid Caster
3:3
Liberator™ Maintenance, Repair and Parts
Fluor. Tube, Speaker, F.-\) and Attraction Panel 178034-024 See Figure 37 (T-Molding) 038988-01 038986-01 (Retainer) (Vent. grille) 03896201 (Cabinet assy.) 78-6900402 R (Tape)
038992-01 Anseae1.0t Lock) (Display shiela) (Locks
038976-02 (Access panel) Control Panel Assy. Video Display See Figure 3-8 : See Figures 3-3 & 3-4 Game PCB Assy. eastossi See Figures 3-11 & 3-12 (Retainer— Midi Trak-Ball™ not shown) See Figure 3-5
A038852-01 (Main harn. assy.) 178013-001 (Latch) A037496-01 (Coin bow'enetosure) Regulator/Audio i
PCB Assy. See Figures 3-11 & 3-13 Utility Panel See Figure 3.9 Coin Door Assy. See Figure 3-10
BQ 038091-01 (Coin box— not shown) A038854.01 (Power harm. assy) Power Supply Assy. See Figure 3-14
A037454-03 (Power cord) 4037470-01 (Onloff switch essy.)
Manuals, Schematics, & Self-Test Label—~ 78-3201 Oossee tt see parts list on following page (Glide) (On/off switch cover)
Figure 3-2 Cabinet-Mounted Assemblies lreland-Built Cabinet A038961-01& -02 A
Liberator™ Maintenance, Repair and Parts
Cabinet-Mounted Assemblies Ireland-Built Cabinet Parts List
Part No. Description A037454-03 Strain-Relief Power Cord (Austria, Belgium, Chile, Denmark, Finland, France, Germany, Greece, Indonesia, Italy, Netherlands, Norway, Spain, Sweden, and Uruguay) A037470-01 Power OnlOff Switch/Mounting Plate Assembly A037496-01 Metal Coin Box Enclosure A038852-01 Main Harness Assembly A038854-01 Power Harness Assembly A038881-01 Lock Assembly (for rear access panel) A038962-01 Cabinet Assembly (includes glides and PCB retainers, but not the rear access panel)
The following six items are the technical information supplements to this game: ‘SP-209 Liberator Schematic Package ST-209-01 Liberator Label with Self-Test Procedure and Option Switch Settings TM-160 Service Manual for 19-Inch Electrohome Color Raster-Scan Display (use with part no. 92-049) TM-201 Service Manual for 19-Inch Wells-Gardner Color Raster-Scan Display (use with part no. 92-055) TM-209 Liberator Operation, Maintenance, and Service Manual TM-220 Service Manual for 19-Inch Matsushita Color Raster-Scan Display (use with part no. 139003-1004) 78-3201 Adjustable Glide 78-6900402 Vinyl Foam Single-Coated Adhesive Tape, ¥%-Inch Wide x Inch Thick 009992-01 On/Off Switch Cover 038091-01 Molded Coin Box (not shown) 038805-01 Display Shield Retainer (not shown) 03897602 Rear Access Panel (does not include lock) 038986-01 Attraction Panel Retainer 038988-01 Ventilation Grille 038992-01 Display Shield 178013-002 Spring Draw Latch 178034-024 34-Inch Black Plastic T-Molding
Maintenance, Repair and Parts
B. The Control Panel
Opening the Control Panel:
- Unlock and open the coin door (see Figure 3-3). Reach up through the opening to the top of the control panel and release the spring-draw latches. For the /reland- Built cabinet, remove the two button-head screws that secure the panel to the lower retainer. 2, Close the coin door.
- Lift the control panel at the top edge and tilt it toward you. The control panel on the Upright cabinet has foam tape on the inside edges. Make sure the tape is in good condition.
Repairing the Leaf Switches:
- Adjust the leaf switches for a narrow gap. When a switch button is pressed, the resulting wiping action of the cross-bar contacts provides a self-cleaning feature. Do not burnish the contacts. To clean them, use electrical contact cleaner.
- To remove a leaf switch, disconnect the wires and remove the screw with a Phillips-head screwdriver. Liberator™
- To remove the switch button, turn the nut with a wrench in a counterclockwise direction from inside the conirol panel. The ring on the outside of the control pane! should not spin.
- Replace the switch, reconnect the harness wires as shown in the Schematic Package, Game Wiring Diagram. Make sure the colored wires are routed to their matching colored tabs on the switch.
Repairing the LED Start Switches:
These switches have a very low failure rate. if you suspect switch failure, test it using the following directions. Testing the LED Switch: |. Disconnect the wires from the switch.
- Attach the leads of an ohmmeter to the normally open and Common contacts.
- Check the contacts (push and release the switch button) for closed and open continuity.
- \f the contacts do not operate sharply or always remain closed or open, replace the switch.
Replacing the LED Switch:
- Disconnect the wires from the switch.
- Turn the switch counterclockwise while holding the biack cone shaped bushing on the outside of the control panel.
- Install a new switch using the reverse procedure.
- Reconnect the wires as shown in Figure 3-3.
1 PLAYER START
WHITE/BLACK
BROWN (Normally open contaci) RED( +)
BLACK (Common contact)
2 PLAYER START WHITE/RED an RED(+)——>ll ORANGE LS5 (Normally open contact)
BLACK (Common contact)
Figure 3-3 Control Panel
3-6
Liberator™ Maintenance, Repair and Parts
Players may receive an electric shock if this control panel is not properly grounded! After servicing any parts on the panel, make sure that the ground wire is firmly attached to the metal tab on the inside of the control panel.
038498.01 A038038-01 Pa NeuN) Midi Trak-Ball™ Assy. (Control panel) i ‘A038499-01 See Figure 35 i 03850604 (Control panel/decal) 4038730-01 (Decal—not shown) (Harness) VERTICAL-MOTION PCB: sanes.0 BLACK, RED, YELLOW, ort ‘ tote 03898501 and GREEN WIRES (Harness (Control panel) A038970-01 038974-04 (Control panel/decal) (Decal—not shown) 7594S (Nut) (
\ 036895-01
(Switch bezel)
75-51488 62-039
(Bolt) (LED switch)
HORIZONTAL-MOTION PCB: 178030-003 BLUE, VIOLET, RED, (Black button) and BLACK WIRES 160013-001 (Leaf switch/button holder)
Figure 3-4 Control Panel Assembly Upright Cabinet A038500-01 A lreland-Built Cabinet A038969-01 A
3-7
Maintenance, Repair and Parts Liberator™
Contro! Panel Assembly Parts List
Part No. Description Upright Cabinet A038499-01 Control Panel with Decal A038730-01 Control Panel Harness Assembly 78-6900402 Vinyl Foam Single-Coated Adhesive Tape, %-Inch Wide x Inch Thick (24 in. required) 038498-01 Control Panel 038506-04 Control Panel Decal
treland-Built Cabinet A038863-01 Control Panel Harness Assembly A038970-01 Control! Panel with Decal 038974-04 Control Panel Deca! 038985-01 Control Panel Upright and Ireland-Built Cabinets A038038-01 Midi Trak-Ball™ Assembly 62-039 SPDT Momentary Pushbutton Start Switch with Red Light-Emitting Diode 75-9418 #10-24 Self-Locking Nut 75-5148B #10-24 Black Carriage Bolt 036895-01 Black Molded Switch Bezel 160013-001 Leaf Switch and Button Holder (leaf switch only is part no. 160012-001) 178030-003 Black Pushbutton Assembly
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Maintenance, Repair and Parts Liberator™
176010-106. (Screw) ® 038039-01 (Upper frame)
LUBRICATE HERE ® (Six places) 038043.01 ) (Midi Trak-Bai)
035937-01 (Ball bearing) 038042-01 or (Joler shaft) s 038041-04 (Roller shatt)
i
035938-01 VERTICAL-MOTION PCB: BLACK, RED, YELLOW, ©® Encoding whee) and GREEN WIRES
\ © bade A036096-01 (Fiat washer) — (Harness assy.) 75-0448 (Spii-iock washer) oF
72-8406 (Hex screw) 139002-001 (Optica! coupler— hidden from view) HORIZONTAL-MOTION PCB: BLUE, VIOLET, RED, and BLACK WIRES.
038040-01 (Lower frame)
Figure 3-5 Midi Trak-Bali™’ Assembly A038038-01 A
3-10
Liberator™
Lubricating the Midi Trak-Bali™: 1, Remove the entire Midi Trak-Ball assembly from the control panel (see Figure 3-4). Remove the six screws. that secure the upper and lower frames together (see Figure 3-5).
- Lift off the top frame.
- Lubricate each of the six ball bearings with two drops of 3 in-One® oil. Lubricate approximately every three months or 6,000 credits (credits are counted on the coin counter).
Removing the Midi Trak-Ball, Coupler PCB and rail Wheel: Follow steps 1 through 3. Then remove the Midi Trak- Ball.
- Lift the PCB out of its slot. Carefully disconnect the red connector and remove ihe PCB. Maintenance, Repair and Parts
- Remove the socket-head screw, flat washer, and splitlock washer that secure the encoding wheel.
- Remove the encoding wheel.
- Reassemble and reinstall in reverse order.
Adjusting the Midi Trak-Ball control:
- When you tighten the encoding wheel, rotate the socket-head screw on the end of the roller shaft until a hole in the shaft is visible through the hole in the top of the frame.
- Insert a inch diameter pin or screwdriver through the hole in the shaft.
- Tighten the socket-head screw with an Allen wrench.
Circled numbers match numbered instructions. Disassemble in the order indicated, SCREWDRIVER OR PIN
SCREWDRIVER MAY BE INSERTED HOLE iN FROM BOTTOM SHAFT @) ALLEN WRENCH
Figure 3-5 Midi Trak-Ball Assembly, continued
Maintenance, Repair and Parts Liberator™
Midi Trak-Ball™ Assembly Parts List
Part No. Description
A035220-02 Coupler PCB Assembly (includes Radial Optical Coupler) A036096-01 Harness Assembly 72-8406 #4-40 x %-Inch, Hex Socket-Head Steel Machine Screw 75-0148, #4 Flat SAE-Standard, Zinc-Plated Steel Washer 75-0448 #4 Split-Lock, Zinc-Plated Steel Washer 034768-01 Label with Lubrication Instructions (not shown) 035937-01 Ball Bearing (6 per assembly) 035938-01 Etched Encoding Wheel 038039-01 Upper Black Plastic Frame 038040-01 Lower Black Plastic Frame 038041-01 Roller Shaft 038042-01 Idler Shaft 038043-01 Midi Trak-Ball (3inch diameter) 139002-001 Radial Optical Coupler (located on the Coupler PCB Assembly) 176010-106 #8 x %Inch Cross-Recessed, Pan-Head, Zinc-Plated Steel Screw
H2
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Maintenance, Repair and Parts Liberator™
C. Fluorescent Tube and Speaker
038495-01 70-304 _78-6900402 (Upper retainer) 03849401 ® (Tube) (Tape) (Attraction glass)
179035-001 (Tube holder) 96-1108 (Tab) t
037469-01 148001.017 (Bracket) (Speaker) A037540-01 (Ground wire)
99-11003 (Starter)
99-11009 (Socket)
79-561816P_ 038505-01 (Wire nut) (Lower retainer)
A038731-01 (Harness)
142028-xxx (Transformer) 038496-01 Grille)
= 038493-01 @ co, ~ (Bezel)
= 038491-01 (Shield)
Circled numbers match num- NOTE bered instructions. Disassemble in the order indicated. To make sure that the fluorescent tube starts, check that the ground wire is firmly attached to both the ballast transformer and the steel “ue lamp bracket.
Figure 3-6 Fluorescent Tube and Speaker Upright Cabinet A038504-01 & -02 A
3-14
Liberator™
Check that the green ground wire is securely attached to the large metal bracket and the ballast transformer on the wood panel. If the tube is not grounded, it may not start.
Upright Cabinet Replacing the Speakers:
- Perform steps 1 and 2. Remove the speaker grille.
| F | : | 7. | Open the control panel, and remove the display glass |
| ‘ | Upright Cabinet | and display bezel. | |
| , | Replacing the Fluorescent Tube: | 8. | Disconnect the 5:pin fluorescent tube and speaker |
s
| ‘ | 1. | Remove the three screws and lock washers that | Ramese connect |
| secure the upper attraction-panel retainer to the cab- | 9. | Remove three screws that secure the tube and |
inet. Loosen the two screws that secure the lower re- speaker board to the cabinet. Hold the board securely tainer to the cabinet. with one hand and remove the fourth screw. Remove
| 2. | Lift the attraction glass up and out of the lower re- | ine board. | . |
tainer. 10. Disconnect the two plug-in connectors on the speaker.
| 3. | Remove the cardboard locking tab at each end of the | poten sottiad illlom ai Goer secu ns ae |
tube. Slightly rotate the tube up or down and carefully p b : it ft the l hold: tach the speaker to the board. Replace the speaker
| remove it from | the lampholders. | and reinstall the tube and speaker board. Be sure that |
| 4. | Replace it with a new tube. Do not snap in the tube vig- | the tube and speaker board is flush with the upper |
orously—you may break it, causing an implosion! front panel when you secure the board to the cabinet. Replace the locking tabs. Reassemble in reverse order.
Fluorescent Tube and Speaker Upright Cabinet Parts List
Part No. Description A037540-01 Ground Wire with Ring Lug A038731-01 Tube and Speaker Harness Assembly 70-304 18-Inch, 15 W, Cool White Fluorescent Tube 78-6900402 Vinyl Foam Single-Coated Adhesive Tape, /4-Inch Wide x Inch Thick 79-561816P Spring-Connector Wire Nut for 16- to 18-Gauge Wires 99-11003 Fluorescent Tube Starter 99-11006 Fiuorescent Tube Locking Tab (tab consists of two pieces) 99-11009 Starter Socket 037469-01 Steel Tube Bracket 038491-01 Video Display Shield 038493-01 Video Display Bezel 038494-01 Attraction Glass with Graphics
038495-01 Upper Attraction Glass Retainer
| . | 038496-01 | Speaker Grille |
| i | (038505-01 | Lower Attraction Glass Retainer |
148001-017 6 x 9-Inch Oval, 8 2, 6-Ounce, Shielded High-Fidelity Speaker 142028-001 60 Hz, 118 V, Ballast Transformer (used on A038504-01 assembly) 142028-002 50 Hz, 118 V, Ballast Transformer (used on A038504-02 assembly) 179035-001 2-Pin Fluorescent Tube Holder
3-15
Maintenance, Repair and Parts
Ireland-Built Cabinet
Replacing the Speaker:
- Remove the three screws that secure the top of the attraction panel to the cabinet.
- Grasp the panel at the top edge and pull it forward (be careful not to damage the speaker that is attached under the grille). Lift the panel up and out of the cabinet. Lay the panel on the top of the cabinet. Liberator™
- Disconnect the two speaker connectors. Note that the white wire (+) connects on the side of the speaker marked with a painted dot. 4, Remove the screws that attach the speaker to the board. Replace the speaker. Reassemble in reverse order.
\reland-Built Cabinet
Replacing the Fluorescent Tube:
- Perform steps 1 and 2. Remove the Y-lead connectors at each end of the tube.
- Replace with a new tube. Do not snap in the tube vigorously—you may break it, causing an implosion! Replace the Y-lead connectors.
- Reassemble in reverse order.
038973.04 (Decal) 035835-01 (Y-lead connector)
148001-001 (Speaker)
038989-01 {Shield)
038987-01 (Grille)
038977-05 (Panel) @
Circied numbers match numbered instructions. Disassemble in the order indicated. 99-11003 (Starter) 99-11009 (Socket)
142028-002 (Transtormer)
A038856-01 (Harness)
99-11012 036978-01 (Clamp) (Board)
To make sure that the fluorescent tube starts, check that the ground wire is firmly attached to the ballast transformer.
Figure 3-7 Fluorescent Tube, Speaker, and Attraction Panel Ireland-Built Cabinet
3-16
Liberator™
Fluorescent Tube, Speaker, and Attraction Panel Ireland-Built Cabinet Maintenance, Repair and Parts
Parts List
Part No. Description A038856-01 Tube and Speaker Harness Assembly 70-303 18-Inch, 15-W, Cool White Fluorescent Tube 99-11003 Fluorescent Tube Starter 99-11009 Starter Socket 99-11012 1 %Inch Fluorescent Tube Clamp. 035835-01 12-Inch Y-Lead Connector 038973-04 Attraction Panel Decal 038977-05 Speaker/Attraction Panel 038978-01 Fluorescent Tube Board 038987-01 Speaker/Attraction Panel Grille 038989-01 Attraction Panel Shield (does not include decal) 142028-002 50 Hz, 118 V, Ballast Transformer 148001-001 6 x 9-Inch Oval, 4 2, 6-Ounce, Shielded High-Fidelity Speaker
3-17
Maintenance, Repair and Parts Liberator™
D. Video Display
- From the back of the cabinet, open the rear access panel. Unplug the display harness connectors and disconnect the ground wire (see Figure 3-8). Remove the hardware that secures the display chassis to the wood display shelf.
- From the front of the cabinet, loosen the screws on the lower retainer. Remove the three screws that secure the speaker grille to the cabinet and remove the grille (see Figure 3-6).
- Open the control panel and remove the display shield (see Figure 3-6).
- Remove the cardboard bezel. Carefully remove the display through the front of the cabinet. Place it on a soft mat in a protected location. After servicing the display, reinstall it in reverse order.
038496-01 a1 Grille)
(Bezel)
°
So ot
038505-01 (Lower retainer)
a a
92.049 (Electronome display) q or 92.055 ©) 038491-01 (Wells Gardner display) (Cisplay shield) or 13003-1004 (Matsushita display)
Figure 3-8 Video Display Upright Cabinet
3-18
Liberator™
lreland-Built Cabinet Removing the Video Display: Ls From the back of the cabinet, open the rear access panel. Unplug the display harness connectors and disconnect the ground wire (see Figure 3-8). From the front of the cabinet, open the contro! panel (see Figure 3-3). Grasp the metal retainer that holds the bottom of the video display shield and slide the retainer and the shield down and out of the cabinet. Remove the cardboard bezel. The wood display shelf is secured to the cabinet with two metal brackets. Remove the two sets of hardware that secure the shelf to these brackets. Carefully pull the wood display shelf and display out through the front of the cabinet. Place the display ina protected location. After servicing the display, reinstall it in reverse order.
038902.01 A038808.01 (Shield) O) (Bezel)
038805-01 (Retainer) 92.049 (Electrohome display) or 92-055 (Wells Gardner display) or 139003-1004 (Matsushita display)
Circled numbers match numbered instructions. Disassemble in the order indicated. © “sre 002728-01 (Bracket)
Figure 3-8 Video Display, continued Ireland-Built Cabinet
3-19
Maintenance, Repair and Parts Liberator™
Video Display Upright and lreland-Built Cabinets Parts List
Part No. Description
For Upright Cabinet 038493-01 Display Bezel 038491-01 Display Shield 038496-01 Speaker Grille 038505-01 Lower Retainer For Ireland-Built Cabinet
A038808-01 Display Bezel 002728-01 Display Sheif Bracket 038804-02 Display Shelf 038805-01 Display Shield Retainer 038992-01 Display Shield For Upright and Ireland-Built Cabinets 92-049 19-Inch Electrohome Color Raster-Scan Display Alternate displays are: 92-055— 19-inch Wells-Gardner Color Raster-Scan Display 139003-1004—19-Inch Matsushita Color Raster-Scan Display
3-20
Liberator™
E. Utility Panel ——= WARNING ——fds Before removing or repairing the utility panel, switch the game to off.
Players may receive an electric shock if the utility panel is not properly grounded! After servicing any parts on the panel, make sure that the ground wire is firmly attached to the metal screw on the back of the coin counter. Maintenance, Repair and Parts
The utility panel is located inside the upper coin door. This panel includes the volume control, self-test switch, auxiliary coin switch, and the coin counter(s). The coin switch is used to credit the game without activating the coin counter.
A002465-01 (Coin counter)
68-001 (Self-test switch) 178070-001 (Volume controi knob)
Figure 3-9 Utility Panel Assembly A038004-01 a (Harness)
038003-01 (Bracket)
62.041 (Auxiliary coin switch)
19-9032 (Volume control)
Parts List
Part No. Description A002465-01 6 V Coin Counter A038004-01 Utility Panel Harness 19-9032 Volume Control 62-041 SPDT Momentary-Contact Pushbutton Auxiliary Coin Switch with Black Cap 69-001 DPDT Self-Test Switch 038003-01 Utility Panel Bracket 178070-001 Volume Control Knob
3-21
Maintenance, Repair and Parts Liberator™
F. Coin Door
170000-001 (Lamp) s 179047.001 99-1023 (Lamp Base) (Base Plate)
99-5056 - 99-15026 (Screw for Bezel) & i (Coin Inlet)
99-15025 BT, (Coin Inlet) nae
PART OF
b 7 Is 99-15054 (Pivot for Lever) 99-15068 (Lockout Coil) 9945069 ra (Lockout < Coil Spring)
/ Z 99-15030 ae > (Lockout Flap)
75-9148 (Hex Nut) 75-056 (Lock Wash.)
99-15075
—~<— 99-15060 (Sw. Cover)
(Switch)
7244148 (Screw)
Figure 3-10 Vertically Mounted Coin Door A037619-xx D
3-22
Liberator™
A037542-01 (Harness—not shown)
99-15063 (Screw)
99-15067 (Lock Assy.)
a
038091-01 (Coin Box)
(Door Frame)
99-15073 99-15070 99-15067. (Lock Assy.)
(Upper Door) | (Doors and Frame) 99-15074 (Lower Door)
A037619-01 — U.S, 25¢/25¢ Coin Door A037619-02 — U.S. 50¢/50¢ Coin Door A037619-03 — Canadian 25¢/25¢ Coin Door A037619-04 — British 10 P/10 P Coin Door A037619-05 — British 10 P/50 P*Coin Door A037619-06 — British 20 P/60 P Coin Door ‘A037619-07 — Australian 20e/20¢ Coin Door ‘A037619-08 — German 1 DM/1 DM Coin Door ‘A037619-09 — German 2 DM/1 DM Coin Door A037619-10 — German 2 DM/S DM Coin Door ‘A037619-11 — German 1 DMi5 DM Coin Door ‘A037619-12 — 5 Fr/5 Fr Coin Door A037619-13 — Swiss 1 F1/1 Fr Coin Door 403761914 — French 1 Fr/1 Fr Coin Door Maintenance, Repair and Parts
99-15038 (Bezel for Button)
99-15001 thru 99-15011 (Return Button)
99-15052 al (Spring for Button) N
99-15071 (Clamp)
99-15039 (Bezel for Cover)
99-15036 (Cover)
ZB
99-15066 (Screw)
‘803761915 — French 2 Fr/1 Fr Coin Door 403761916 — Swedish 1 Kri1 Kr Coin Door A037619-17 — Spanish 25 Pts/25 Pts Coin Door ‘403761918 — Italian 100 L/100 L Coin Door ‘03761919 — Hong Kong $1/$1 Coin Door ‘A037619-20 — Japanese 100Y/00Y Coin Door
Figure 3-10 Vertically Mounted Coin Door, continued A037619-xx D
3-23
Maintenance, Repair and Parts Liberator™
Vertically Mounted Coin Door Parts List
Part No. Description A037542-01 Harness Assembly 7214148 #4-40 x Inch Cross-Recessed Pan-Head Steel Machine Screw 75-056 #6 Internal-Tooth Zinc-Plated Steel Lock Washer 75-914S #4-40 Steel Machine Hex Nut 75-3414S #4-40 x %-Inch 82° Cross-Recessed Flat-Head Steel Machine Screw 99-15001 Coin Return Button with U.S. 25¢ Price Plate 99-15002 Coin Return Button with U.S. $1 Price Plate 99-15003 Coin Return Button with German 1 DM Price Plate 99-15004 Coin Return Button with German 2 DM Price Plate 99-15005 Coin Return Button with German 5 DM Price Plate 99-15006 Coin Return Button with Belgian 5 Fr Price Plate 99-15007 Coin Return Button with French 1 Fr Price Plate 99-15008 Coin Return Button with Japanese 100 Yen Price Plate 99-15009 Coin Return Button with British 10 Pence Price Plate 99-15010 Coin Return Button with Australian 20¢ Price Plate 99-15011 Coin Return Button with Italian 100 Lire Price Plate 99-15023 Base Plate 99-15025 Left Half of Coin Inlet 99-15026 Right Half of Coin Inlet 99-15027 Side Plate of Coin Return Box 99-15028 Base Plate of Coin Return Box 99-15029 Switch Bracket 99-15030 Flap for Lockout Coil (U.S. 25¢) 99-15036 Metal Coin Return Cover 99-15038 Bezel for Coin Return Button 99-15039 Metal Bezel for Coin Return Cover 99-15040 Coin Return Lever 99-15042 Coin Switch for U.S. 25¢ 99-15052 Spring for Coin Return Button 99-15054 Pivot for Coin Return Lever 99-15055 Retaining Screw 99-15056 #4-40 x %,-Inch Cross-Recessed Pan-Head Steel Machine Screw 99-15060 Switch Cover 99-15063 Screw for Hinge 99-15066 Screw for Clamp 99-15067 Lock Assembly 99-15068 Lockout Coil 99-15069 Spring for Lockout Coil 99-15070 Doors and Frame 99-15071 Clamp for Frame 99-15072 Door Frame 99-15073 Upper Door 99-15074 Lower Door 99-15075 Switch Adjuster 038091-01 Coin Box (Not included in assembly) Acceptable substitute is part number A037491-01 170000-001 6.3V Miniature Wedge-Base Incandescent Lamp 171006-035 Metal Coin Mechanism 179047-001 Lamp Base
3-24
Liberator™ Maintenance, Repair and Parts
G. Printed-Circuit Boards
femoung the Printed-Circuit Boards: Open the rear access panel. Before you remove or repair any printed-circuit board (PCB), switch the game to off. §. Remove the screw and two spacers that secure the Regulator/Audio |i PCB to the cabinet, and carefully remove the board from its slot. Do not twist the board, as this may loosen connections or components. Replace or repair as required, and reinstall the PCB.
Make sure that the connectors on the PCB are
For the game PCB, unplug the two edge connectors (see Figure 3-11). Remove the screw and two washers that secure the PCB to the cabinet. Caretully slide the PCB straight out of its slots. Be careful not to twist the board, as this may loosen connections or components. Replace or repair as required, and reinstall the PCB. For the Reguiator/Audio |/ PCB, disconnect the five smali harness connectors on this board. properly plugged in. Note that they are keyed to fit only one way. If they do not slip on easily, do not force them. A reversed connector may damage your game and void the warranty.
Close and lock the rear access panel. Make sure that the game is operating correctly by performing the self-test. Performing self-test is very
Printed-Circuit Board Mounting Hardware Parts List
Part No. Description
72-6810S #8 x 5Inch Cross-Recessed Pan-Head Screw 034536-02 Foam Pad 038178-03 Dual-Slotted Retainer 175004-708 #8 Fiber Washer 176015-110 #10 x %-Inch Pan-Head Screw
038178-03 (Retainer) 176015-110 i 034536-02 (Foam pac) (Screw) 72-8810S Screw
175004-708 (Washer) 175004708 178015-110 @y~ (wasrer) (Screw) 72-6810S (Screw)
- ,,, Avseoseor (Liberator Game PCB)
‘A035435.02 (Reguiator/ Audio I PCB)
034536-02 (Foam pad)
Figure 3-11 Removing the Printed-Circuit Boards
3-25
Liberator™
Maintenance, Repair and Parts
a pore Jae ben] oo ol fan] vary Sexae tp. Seo) Soe teeaae] SGD peste heer grsaoz fed ee ‘ fee) az lewe have! pas ria ie = cy ¥ s = 9
= - — Dicezs) faa] 5 pees! g Sane! freaal a HOHE By =
2 ae
7m 9008 > = x
A038068-21 B Acceptable substitutes are A038068-11 and A038068-31. Figure 3-12 Liberator™ Game PCB Assembly pyvezezr 4o
3-26
Liberator™
Liberator™ Game PCB Assembly Maintenance, Repair and Parts
Parts List
| Designator | Description | Part No. |
Capacitors
| C1-C61 | 0.1 uF, +80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor | 122002-104 |
| C62 | 22 pF, 100 V, Epoxy-Dipped Mica Radial-Lead Capacitor | 128002-220 |
| C63 | 68 pF, 100 V, Epoxy-Dipped Mica Radial-Lead Capacitor | 128002-680 |
| Ce4 | 0.22 uF, +80, -20%, 25 V Ceramic-Disk Radial-Lead Capacitor | 122008-224 |
| C65 | 0.1 uF, +80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor | 122002-104 |
| C66 | 0.22 uF, +80, -20%, 25 V Ceramic-Disk Radial-Lead Capacitor | 122008-224 |
| C67 | 0.1 uF, +80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor | 122002-104 |
| C68 | 0.22 uF, +80, -20%, 25 V Ceramic-Disk Radial-Lead Capacitor | 122008-224 |
| C69 | 0.1 uF, + 80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor | 122002-104 |
| C70 | 0.22 uF, +80, -20%, 25 V Ceramic-Disk Radial-Lead Capacitor | 122008-224 |
| C71 | 0.1 uF, +80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor | 122002-104 |
| C72 | 0.22 uF, +80, -20%, 25 V Ceramic-Disk Radial-Lead Capacitor | 122008-224 |
| C73 | 0.1 pF, +80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor | 122002-104 |
| C74 | 0.22 pF, +80, -20%, 25 V Ceramic-Disk Radial-Lead Capacitor | 122008-224 |
| C75 | 0.1 uF, + 80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor | 122002-104 |
| C76 | 0.22 uF, +80, -20%, 25 V Ceramic-Disk Radial-Lead Capacitor | 122008-224 |
| c77 | 0.1 uF, +80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor | 122002-104 |
| c78 | 0.22 uF, +80, -20%, 25 V Ceramic-Disk Radial-Lead Capacitor | 122008-224 |
| c79 | 0.1 uF, +80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor | 122002-104 |
| C80 | 0.22 uF, +80, -20%, 25 V Ceramic-Disk Radial-Lead Capacitor | 122008-224 |
| C81 | 0.1 uF, +80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor | 122002-104 |
| C82 | 0.22 uF, +80, -20%, 25 V Ceramic-Disk Radial-Lead Capacitor | 122008-224 |
| C83 | 0.1 uF, +80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor | 122002-104 |
| C84 | 0.22 uF, +80, -20%, 25 V Ceramic-Disk Radial-Lead Capacitor | 122008-224 |
| C85 | 0.1 uF, +80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor | 122002-104 |
| C86 | 0.22 uF, +80, -20%, 25 V Ceramic-Disk Radial-Lead Capacitor | 122008-224 |
| C87, C88 | 0.1 uF, +80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor | 122002-104 |
| C89-C102 | 0.22 yF, +80, -20%, 25 V Ceramic-Disk Radial-Lead Capacitor | 122008-224 |
| C103, C104 | 0.01 pF, + 80, -20%, 25 V Ceramic-Disk Axial-Lead Capacitor | 122005-103 |
| C105 | 0.1 uF, +80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor | 122002-104 |
| C106 | 2.2 uF, + 10%, 35 V Tantalum Capacitor | 122000-225 |
| C107-C119 | 0.1 uF, +80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor | 122002-104 |
| C120 | 100 pF, 25 V, Aluminum Electrolytic Axial-Lead Capacitor | 24-250107 |
| C121-C134 | 0.1 pF, +80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor | 122002-104 |
| C135 | 1000 pF, 100 V, Epoxy-Dipped Mica Radial-Lead Capacitor | 128002-102 |
| C136-C140 | 1 pF, 50 V, Aluminum Electrolytic Axial-Lead Capacitor | 24-500105 |
| C141-C144 | 0.01 uF, +80, -20%, 25 V Ceramic-Disk Axial-Lead Capacitor | 122005-103 |
| C145-C147 | 47 uF, 50 V, Aluminum Electrolytic Axial-Lead Capacitor | 24-500476 |
| C148-C150 | 100 yF, 25 V, Aluminum Electrolytic Axial-Lead Capacitor | 24-250107 |
| C151 | 0.1 uF, +80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor | 122002-104 |
| C152 | 0.01 uF, + 80, -20%, 25 V Ceramic-Disk Axial-Lead Capacitor | 122005-103 |
| C153-C156 | 0.1 uF, +80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor | 122002-104 |
| C157 | 220 pF, 100 V, Epoxy-Dipped Mica Radial-Lead Capacitor | 128002-221 |
| C158-C161 | 0.01 uF, +80, -20%, 25 V Ceramic-Disk Axial-Lead Capacitor | 122005-103 |
| C162 | 330 pF, 100 V, Mica Capacitor | 128002-331 |
| C163 | 68 pF, 100 V, Epoxy-Dipped Mica Radial-Lead Capacitor | 128002-680 |
(Continued on next page)
3-27
Maintenance, Repair and Parts Liberator™
Liberator™ Game PCB Assembly Parts List, continued
| Designator | Description | Part No. |
| CRi | Type-MV5053 Light-Emitting Diode | 38-MV5053, |
| CR2 | Type1N751A, +5%, 5.1 V, 500 mW Zener Diode | 32-1N751A |
| CR3-CRS | Type-1N914, 75 V Switching Diode | 31-1N914 |
| CRE | Type1N5257B, +5%, 33 V Zener Diode | 131003-001 |
Integrated Circuits
| AG | Type-74LS174 Integrated Circuit | 137209-001 |
| AT | Type-74LS83 Integrated Circuit | 37-74LS83 |
| Ag | Type-74S04 Integrated Circuit | 37-74S04 |
| All | Type-74LS174 Integrated Circuit | 137209-001 |
| Al2 | Type-74LS14 Integrated Circuit | 37-74LS14 |
| A13 | Type-4066B Integrated Circuit | 37-4066 |
| BI | Type-74LS367 Integrated Circuit | 37-74LS367 |
| BS | Type-7400 Integrated Circuit | 37-7400 |
| BE | Type-74LS191 Integrated Circuit | 37-74LS191 |
| B7 | Type-74S 189 Integrated Circuit | 37-74S189 |
| BB | Type-74S74 Integrated Circuit | 37-74S74 |
| BO | Type-74S02 Integrated Circuit | 37-74S02 |
| B10 | Type-LM324 Integrated Circuit | 37-LM324 |
| B11 | Type-74S 189 Integrated Circuit | 37-74S189 |
| B12 | Type-7407 Integrated Circuit | 37-7407 |
| B13 | Type-4066B Integrated Circuit | 37-4066 |
| C1 | Type-74LS33 Integrated Circuit | 137239-001 |
| Ccé | Type-74S85 Integrated Circuit | 37-74S85 |
| C7 | Type-74S 189 Integrated Circuit | 37-748 189 |
| C8, C9 | Type-74S74 Integrated Circuit | 37-74S74 |
| ci | Type-74S189 Integrated Circuit | 37-74S189 |
| C12 | Type-7407 Integrated Circuit | 37-7407 |
| D1 | Type-74LS33 Integrated Circuit | 137239-001 |
| DS | Type-74S74 Integrated Circuit | 37-74S74 |
| D6 | Type-74LS191 Integrated Circuit | 37-74LS191 |
| D7 | Type-74S189 Integrated Circuit | 37-74S189 |
| D8. | Type-74S74 Integrated Circuit | 37-74S74 |
| Dg | Type-74109 Integrated Circuit | 37-74109 |
| D10, D11 | Type-74LS174 Integrated Circuit | 137209-001 |
| —1 | Type-74LS244 Integrated Circuit | 37-74LS244 |
| E2 | Type-74LS245 Integrated Circuit | 37-74LS245, |
| E3 | Type-74LS367 Integrated Circuit | 37-74LS367 |
| E4 | Type-74LS139 Integrated Circuit | 37-74LS139 |
| E5 | Type-74LS74 Integrated Circuit | 37-74LS74 |
| E6 | Type-74S85 Integrated Circuit | 37-74885 |
| &7 | Type-74S 189 Integrated Circuit | 37-74S189 |
3-28 (Continued on next page)
Liberator™ Maintenance, Repair and Parts
Liberator™ Game PCB Assembly Parts List, continued
| Designator | Description | Part No. |
| E8 | Type-74S74 Integrated Circuit | 37-74S74 |
| EQ | Type-74163 Integrated Circuit | 37-74163 |
| E11 | Type-74S189 Integrated Circuit | 37-74S189 |
| F1 | Type-74LS374 Integrated Circuit | 37-74LS374 |
| F2 | Type-74LS244 integrated Circuit | 37-74LS244 |
| F3 | Type-74LS32 Integrated Circuit | 37-74LS32 |
| F4 | Type-74LS04 integrated Circuit | 37-74LS04 |
| F5. | Type-74LS02 Integrated Circuit | 37-74LS02 |
| Fe | Type-74LS174 Integrated Circuit | 137209-001 |
| F? | Type-74LS83 Integrated Circuit | 37-74LS83 |
| Fa | Type-74S08 Integrated Circuit | 37-74808 |
| FQ | Type-74160 Integrated Circuit | 37-74160 |
| Flt | Type-74S189 Integrated Circuit | 37-748 189 |
| FIH12 | Type-LM324 Integrated Circuit | 37-LM324 |
| H1 | Type-74LS374 Integrated Circuit | 37-74L.S374 |
| H2 | Type-74LS244 Integrated Circuit | 37-74L8244 |
| H3 | Type-74LS32 Integrated Circuit | 37-74LS32 |
| H4 | Type-74LS00 Integrated Circuit | 37-74LS00 |
| H5 | ‘Type-74S74 Integrated Circuit | 37-74S74 |
| H6 | Type-74LS 174 Integrated Circuit | 37-74LS174 |
| H7 | Type-74LS193 Integrated Circuit | 37-74LS193 |
| H8 | Type-74LS163A Integrated Circuit | 37-74LS163A |
| Ho | Type-74153 Integrated Circuit | 37-74153 |
| Hit | Type-74LS157 Integrated Circuit | 37-74LS157 |
| J3 | Type-74LS32 Integrated Circuit | 37-74LS32 |
| J4 | Type-74S32 Integrated Circuit | 37-74S32 |
| J5 | Type-74LS32 integrated Circuit | 37-74LS32 |
| J6 | Type-74LS195 Integrated Circuit | 137208-001 |
| J? | Type-74S189 Integrated Circuit | 37-74S189 |
| J8 | Type-74LS163A Integrated Circuit | 37-74LS 163A |
| J9 | Type-74153 Integrated Circuit | 37-74153 |
| Jt | Type-74LS197 integrated Circuit | 137240-001 |
| K2 | Type-74LS374 Integrated Circuit | 37-74LS374 |
| K3 | Type-74LS74 Integrated Circuit | 37-74LS74 |
| K4 | Type-74109 Integrated Circuit | 37-74109 |
| K5 | Type-74LS399 Integrated Circuit | 37-74LS399 |
| K6. | Type-74LS195 Integrated Circuit | 137208-001 |
| K7 | Type-74S189 Integrated Circuit | 37-74S189 |
| K9 | Type-74153 Integrated Circuit | 37-74153 |
| K11 | Schmitt Trigger Hex Integrated Circuit | 37-4584B |
| K12, | Type-TL082 Integrated Circuit | 37-TLO82CP |
| 13 | Type-74LS04 Integrated Circuit | 37-74LS04 |
| L4 | Type-74LS08 Integrated Circuit | 37-74LS08. |
| L5 | Type-74S 189 Integrated Circuit | 37-74S189 |
(Continued on next page)
3-29
Maintenance, Repair and Parts Liberator™
Liberator™ Game PCB Assembly Parts List, continued
| Designator | Description | Part No. |
| L6 | Type-74LS283 Integrated Circuit | 137241-001 |
| u7 | Type-74LS157 Integrated Circuit | 37-74LS157 |
| Ls | Type-74LS273 Integrated Circuit | 37-74LS273 |
| Lo | Type-74153 Integrated Circuit | 37-74153 |
| Lu | Type-74LS74 Integrated Circuit | 37-74LS74 |
| M3 | Type-74S86 Integrated Circuit | 137002-001 |
| M4 | Type-74LS175 Integrated Circuit | 37-74LS175 |
| M5 | Type-74LS21 Integrated Circuit | 137210-001 |
| M6 | Type-74LS283 Integrated Circuit | 137241001 |
| M7 | Type-74LS193 Integrated Circuit | 37-74LS193 |
| M9 | Type-74LS195 Integrated Circuit | 37-74LS195 |
| M11 | Type-74LS257 Integrated Circuit | 37-74LS257 |
| N3 | Type-74LS74 Integrated Circuit | 37-74LS74 |
| N4 | Type-74S02 Integrated Circuit | 37-74802 |
| N5 | Type-74S260 Integrated Circuit | 37-74S260 |
| N7 | Type-74LS174 Integrated Circuit | 37-7ALS 174 |
| NO | Type-74LS253 Integrated Circuit | 37-74LS253 |
| N11 | Type-74LS191 Integrated Circuit | 37-74LS191 |
| P2 | Type-74LS174 Integrated Circuit | 97-74LS174 |
| P3. | Type-74LS08 Integrated Circuit | 37-74LS08 |
| P4 | Type-74LS00 Integrated Circuit | 37-74LS00 |
| P5 | Type-74LS174 integrated Circuit | 137209-001 |
| P7 | Type-74LS83 Integrated Circuit | 37-74LS83 |
| PQ | Type-74LS195 Integrated Circuit | 37-74LS195 |
| Pt | Type-74LS157 Integrated Circuit | 37-74LS157 |
| R2 | Type-74LS175 Integrated Circuit | 37-74LS175 |
| R3 | Type-74LS32 Integrated Circuit | 37-74LS32 |
| Ra | Type-74L.$08 Integrated Circuit | 37-74LS08 |
| RS | Type-74LS174 Integrated Circuit | 137209-001 |
| R6 | Type-74LS273 Integrated Circuit | 37-74LS273 |
| R7 | Type-74LS83 Integrated Circuit | 37-74LS83 |
| RQ | Type-74LS195 Integrated Circuit | 37-74LS195 |
| R11 | Type-74LS257 Integrated Circuit | 37-74LS257 |
| $2 | Type-74LS42 Integrated Circuit | 37-74LS42 |
| $3 | Type-74LS74 Integrated Circuit | 37-74LS74 |
| $4 | Type-74LS175 Integrated Circuit | 37-74LS175, |
| $5 | Type-74153 Integrated Circuit | 37-74153. |
| S6 | Type-74LS165 Integrated Circuit | 37-74LS165 |
| so | Type-74LS253 Integrated Circuit | 37-74LS253 |
| si | Type-74LS191 Integrated Circuit | 37-74LS191 |
| T2, 13 | Type-74LS139 Integrated Circuit | 37-74LS139 |
| T4 | Type-74LS74 Integrated Circuit | 37-74LS74 |
| 5 | Type-74153 Integrated Circuit | 37-74153 |
| T9 | Type-74LS244 Integrated Circuit | 37-74LS244 |
| HN | Type-74LS259 Integrated Circuit | 37-74LS259 |
(Continued on next page)
3-30
Liberator™
Liberator™ Game PCB Assembly Parts List, continued Maintenance, Repair and Parts
| Designator | Description | Part No. |
Resistors
| R1 | 1kQ, +5%, V4 W Resistor | 110000-102 |
| R2-19 | 10 kQ, +5%, Vs W Resistor | 110000-103 |
| R20-R22 | 1kQ, +5%, % W Resistor | 110000-102 |
| R23-R38 | 10 k2, +5%, % W Resistor | 110000-103 |
| R39 | 1kQ, +5%, % W Resistor | 110000-102 |
| R40 | 10 kQ, +5%, % W Resistor | 110000-103 |
| R41, R42 | 27 Q, +5%, V4 W Resistor | 110000-270 |
| R43, R44 | 10 kQ, +5%, ¥4 W Resistor | 110000-103 |
| R45, | 27 Q, +5%, vs W Resistor | 110000-270 |
| R46 | 10 kQ, +5%, % W Resistor | 110000-103 |
| R47 | 27 Q, +5%, v4 W Resistor | 110000-270 |
| R48 | 10 kQ, +5%, % W Resistor | 110000-103 |
| R49-R57 | 1k@, +5%, % W Resistor | 110000-102 |
| R58 | 10 kQ, +5%, 4 W Resistor | 110000-103 |
| R59 | 220 2, +5%, V4 W Resistor | 110000-221 |
| R60 | 27 Q, +5%, % W Resistor | 110000-270 |
| R61, R62 | 10 kQ, +5%, 14 W Resistor | 110000-103 |
| R63 | 27 Q, +5%, 14 W Resistor | 110000-270 |
| R64, R65 | 1kQ, +5%, % W Resistor | 110000-102 |
| R66 | 27 2, +5%, V4 W Resistor | 110000-270 |
| R67, R68 | 100 k2, +5%, v4 W Resistor | 110000-104 |
| R69, R70 | 4.7 kQ, +5%, Ys W Resistor | 110000-472 |
| R71-R73 | 100 k2, +5%, V4 W Resistor | 110000-104 |
| R74 | 47 kQ, +5%, v4 W Resistor | 110000-473 |
| R75, R76 | 1kQ, +5%, 1% W Resistor | 110000-102 |
| R77 | 150 2, +5%, % W Resistor | 110000-151 |
| R78-R81 | 1kQ, +5%, % W Resistor | 110000-102 |
| R82-R85 | 470 Q, +5%, % W Resistor | 110000-471 |
| R86, R87 | 220 Q, +5%, v4 W Resistor | 110000-221 |
| R88, R89 | 470 2, +5%, V4 W Resistor | 110000-471 |
| R90-R93 | 1 kQ, +5%, %4 W Resistor | 110000-102 |
| R94-R97 | 470 2, +5%, Vs W Resistor | 110000-471 |
| R98-R103 | 1kQ, +5%, Y W Resistor | 110000-102 |
| R104-R107 | 470 2, +5%, Vs W Resistor | 110000-471 |
| Ri08-R111 | 10 kQ, +5%, %4 W Resistor | 110000-103 |
| R112 | 1kQ, +5%, v4 W Resistor | 110000-102 |
| R113 | 10 kQ, +5%, % W Resistor | 110000-103 |
| R114-R117 | 3.3 kQ, +5%, % W Resistor | 110000-332 |
| R118 | 10 kQ, +5%, ‘4 W Resistor | 110000-103 |
| R119 | 220 2, +5%, v4 W Resistor | 110000-221 |
| R120 | 22 kQ, +5%, V4 W Resistor | 110000-223 |
| R121 | 68 kQ, +5%, v4 W Resistor | 110000-683 |
| R122 | 220 2, +5%, v4 W Resistor | 110000-221 |
| R123 | 1k, +5%, % W Resistor | 110000-102 |
{Continued on next page]
3-31
Maintenance, Repair and Parts Liberator™
Liberator™ Game PCB Assembly Parts List, continued
| Designator | Description | Part No. |
| R124 | 3.3 kQ, +5%, Vs W Resistor | 110000-332 |
| R125, R126 | 10 kQ, +5%, % W Resistor | 110000-103 |
| R127 | 1kQ, +5%, Ye W Resistor | 110001-102 |
| R128, R129 | 1kQ, +5%, % W Resistor | 110000-102 |
| R130 | 4.7 kQ, +5%, % W Resistor | 110000-472 |
| R131 | 10 kQ, +5%, % W Resistor | 110000-103 |
| R132 | 22 kQ, +5%, V4 W Resistor | 110000-223 |
| R133, R134 | 1kQ, +5%, Ys W Resistor | 110000-102 |
| R135 | 2.2 kQ, +5%, % W Resistor | 110000-222 |
| R136 | 8.2 kQ, +5%, V4 W Resistor | 110000-822 |
| R137 | 4.7 kQ, +5%, V4 W Resistor | 110000-472 |
| R138-R140 | 1kQ, +5%, % W Resistor | 110000-102 |
| R141 | 4.7 kQ, +5%, Vv W Resistor | 110000-472 |
| R142 | 10 kQ, +5%, % W Resistor | 110000-103 |
| R143 | 22 kQ, +5%, % W Resistor | 110000-223 |
| R144 | 1kQ, +5%, % W Resistor | 110000-102 |
| R145-R147 | 100 2, +5%, % W Resistor | 110000-101 |
| R148-R150 | 1kQ, +5%, % W Resistor | 110000-102 |
| R151 | 4.7 kQ, +5%, % W Resistor | 110000-472 |
| R152 | 10 kQ, +5%, % W Resistor | 110000-103 |
| R153 | 22 k2, +5%, % W Resistor | 110000-223 |
| R154 | 1kQ, +5%, % W Resistor | 110000-102 |
| R155 | 470 Q, +5%, %4 W Resistor | 110000-471 |
| R156 | 220 2, +5%, v4 W Resistor | 110000-221 |
| R157 | 1.5 kQ, + 5%, v4 W Resistor | 110000-151 |
| R158-R160 | 1kQ, +5%, % W Resistor | 110000-102 |
| R161 | 330 Q, +5%, % W Resistor | 110000-331 |
| R162 | 470 Q, +5%, % W Resistor | 110000-471 |
| R163 | 330 Q, +5%, % W Resistor | 110000-331 |
| Ri64 | 10 k2, +5%, % W Resistor | 110000-103 |
Programmable Read-Only Memories
| C5 | Programmable Read-Only Memory | 136012-121 |
| K8 | Programmable Read-Only Memory | 136012-122 |
| N6 | Programmable Read-Only Memory | 136012-123 |
| P6 | Programmable Read-Only Memory | 136012-124 |
| 17 | Programmable Read-Only Memory | 136012-125, |
| s7 | Programmable Read-Only Memory | 136012-126 |
For -11 version only
| C2 | Type-6502A Microprocessor | 90-6013 |
| BIC3 | Audio 1/0 N-Channel MOS/LSI Custom Chip | C012294-01 |
| CID3 | Audio /O N-Channel MOS/LSI Custom Chip | C012294-01 |
| J1 | Type-137 184-001 Programmable Read-Only Memory | 136012-216 |
3-32 (Continued on next page)
Liberator™
Liberator™ Game PCB Assembly Parts List, continued Maintenance, Repair and Parts
| Designator | Description | Part No. |
| KILA | Type-137184-001 Programmable Read-Only Memory | 136012-215 |
| uM?1 | Type-137184-001 Programmable Read-Only Memory | 136012-214 |
| M2 | 4 us, 64 x 8, Tri-State Electrically Alterable Read-Only Memory | 137161-001 |
| MIN8 | Type-137184-001 Programmable Read-Only Memory | 136012-118 |
| N1 | Type-137184-001 Programmable Read-Only Memory | 136012-213 |
| Ps | Type-137184-001 Programmable Read-Only Memory | 136012-120 |
| PIR1 | Type-137184-001 Programmable Read-Only Memory | 136012-212 |
| R/S | Type-137184-001 Programmable Read-Only Memory | 136012-211 |
| RISB | Type-137184-001 Programmable Read-Only Memory | 136012-117 |
| 1 | Type-137184-001 Programmable Read-Only Memory | 136012-228 |
| 8 | Type-137184-001 Programmable Read-Only Memory | 136012-119 |
For -27 version only
| c2 | Type-6502A Microprocessor | 90-6013 |
| BIC3 | Audio VO N-Channel MOS/LSI Custom Chip | C012294-01 |
| c/D3 | Audio 1/0 N-Channel MOS/LSI Custom Chip | C012294-01 |
| J | Type-137171-001 Electrically Programmable Read-Only Memory | 136012-206 |
| K/L1 | Type-137171-001 Electrically Programmable Read-Only Memory | 136012-205 |
| uM1 | Type-137171-001 Electrically Programmable Read-Only Memory | 136012-204 |
| M2 | 4 uSec, 64 x 8, Tri-State Electrically Alterable Read-Only Memory | 137161-001 |
| M/N8& | Type-137171-001 Electrically Programmable Read-Only Memory | 136012-108 |
| NI | Type-137171-001 Electrically Programmable Read-Only Memory | 136012-203 |
| P38. | Type-137171-001 Electrically Programmable Read-Only Memory | 136012-110 |
| PIRI | Type-137171-001 Electrically Programmable Read-Only Memory | 136012-202 |
| RIS1 | Type-137 171-001 Electrically Programmabie Read-Only Memory | 136012-201 |
| RISB | Type-137171-001 Electrically Programmable Read-Only Memory | 136012-107 |
| T1 | Type-137171-001 Electrically Programmable Read-Only Memory | 136012-200 |
| 8 | Type-137171-001 Electrically Programmable Read-Only Memory | 136012-109 |
For -31 version only
| c2 | Type-6502A Microprocessor | 90-6013 |
| BIC3 | Audio I/O N-Channel MOS/LSI Custom Chip | C012294-01 |
| CID3 | Audio 1/0 N-Channel MOS/LS! Custom Chip | 01229401 |
| J | Type-137171-001 Electrically Programmable Read-Only Memory | 136012-206 |
| K/L1 | Type-137171-001 Electrically Programmable Read-Only Memory | 136012-205 |
| LiM1 | Type-137171-001 Electrically Programmable Read-Only Memory | 136012-204 |
| M2 | 4 us, 64 x 8, Tri-State Electrically Alterabie Read-Only Memory | 137161-001 |
| M/N8. | Type-137 171-001 Electrically Programmable Read-Only Memory | 136012-118 |
| N1 | Type-137171-001 Electrically Programmable Read-Only Memory | 136012-203 |
| P83 | Type-137 171-001 Electrically Programmable Read-Only Memory | 136012-120 |
| PIR1 | Type-137171-001 Electrically Programmable Read-Only Memory | 136012-202 |
| RIS1 | Type-137171-001 Electrically Programmable Read-Only Memory | 136012-201 |
| RISB | Type-137171-001 Electrically Programmable Read-Only Memory | 136012-117 |
| 11 | Type-137171-001 Electrically Programmable Read-Only Memory | 136012-200 |
| 8 | Type-137171-001 Electrically Programmable Read-Only Memory | 136012-119 |
[Continued on next page]
3-33
Maintenance, Repair and Parts Liberator™
Liberator™ Game PCB Assembly Parts List, continued
| Designator | Description | Part No. |
Random-Access Memories
| E10 | Random-Access Memory | 100017-001 |
| F10 | Random-Access Memory | 100017-001 |
| H10 | Random-Access Memory | 100017-001 |
| J10 | Random-Access Memory | 100017-001 |
| K10 | Random-Access Memory | 100017-001 |
| L10 | Random-Access Memory | 100017-001 |
| M10 | Random-Access Memory | 100017-001 |
| N10 | Random-Access Memory | 100017-001 |
| P10 | Random-Access Memory | 100017-001 |
| R10 | Random-Access Memory | 100017-001 |
| $10 | Random-Access Memory | 100017-001 |
| T10 | Random-Access Memory | 100017-001 |
Sockets
| BIC3 | 40-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C40 |
| c2 | 40-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C40 |
| C/ID3 | 40-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C40 |
| Jd | 24-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C24 |
| K/L | 24-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C24 |
| LIM1 | 24-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C24 |
| M2 | 22-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C22 |
| M/N8& | 24-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C24 |
| Nt | 24-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C24 |
| P38 | 24-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C24 |
| P/R1 | 24-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C24 |
| RIS1 | 24-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C24 |
| RISB | 24-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C24 |
| 1 | 24-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C24 |
| 8 | 24-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C24 |
Switches
| AG | 8-Station, SPST, Dual-Inline-Package Switch | 66-118P1T |
| 04 | 8-Station, SPST, Dual-Inline-Package Switch | 66-118P1T |
| 112 | 4-Station, SPST, Dual-Inline-Package Switch | 66-114P1T |
Transistors
| Qi | Type-2N3904 NPN 60 V, 1W Transistor | 34-2N3904 |
| Q2, Q3 | Type-2N6044 Darlington NPN, 80 V, 8 A Transistor | 34-2N6044 |
| Q4 | Type-2N3904 NPN 60 V, 1W Transistor | 34-2N3904 |
| Q5 | Type-2N3906 PNP 40 V, 1W Transistor | 33-2N3906 |
(Continued on next page)
3-34
Liberator™ Maintenance, Repair and Parts
Liberator™ Game PCB Assembly Parts List, continued
| Designator | Description | Part No. |
| a6 | Type-2N3904 NPN 60 V, 1W Transistor | 34-2N3904 |
| Q7 | Type-2N3906 PNP 40 V, 1W Transistor | 33-2N3906 |
| Qs | Type-2N3904 NPN 60 V, 1W Transistor | 34-2N3904 |
| ag | Type-2N3906 PNP 40 V, 1W Transistor | 33-2N3906 |
| Q10, Q11 | Type-2N3904 NPN 60 V, 1W Transistor | 34-2N3904 |
Miscellaneous
Test Point Acceptable substitute is part no. 020670-01 179051-002
| Q2, Q3 | Nylon Snap-In Fastener | 81-4302 |
| ut | 100 pH, + 10%, Hot-Molded Plastic Fixed R.F. Choke Acceptable substitute is part | 141002-001 |
no. 41-3003
| YI | 20.00 MHz Crystal | 144000-003 |
3-35
3-36 Maintenance, Repair and Parts
| U | bt | rm |
4 o
- § n= 3
| = | Re | | |
g CRE
| 4—}<R7 | S | 0 |
RS e
| cp | oo | a | |
| t20 | cai | 0 | ad |
« 19 BY
| —+ | 3300 | [— |
S5V
5380 +
| [— _ | c23 | cal | |
| 35V | fein} | e322 | |
| A265 | AHF} | +22 | |
| & | —Gasw+ | cee | C2 |
5.6K fer} Oop 2812 7905
| (@) | R240. 7W | oO | |
| TIP 32 | TDA2ZOOZA | TDAZ002A | |
| TAG? | _INAGOZ QS | ; | a |
cRe 0 + Im
| a A | eS | Den) | ° cereals | |
| q | 33 | jo COG | |,o| | cisczn |
| ce Gal | TEEIRI4 OS) | R220 4 | ||
| Ee) | RS | 220 | R2I, /2w | ||
| 0 | Boe | BRE | l | Cla |
| sit] SS | oN | 7 | +e | |
| zh SQ | ste | an | 470 |
x a st YY GIR:
| J | oc | coc |
470 RI
mM 8g 3300, Fo+ 3 |
| = | 0 | 220 | BBV |
R30 RD 1/2W Ht cry
| " (—F INsoo2, | 0 | i |
Liberator™
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL Reproduction forbidden without the specific ‘weten permission of Atari Inc., Sunnyvale, CA This drawing iS ‘only conditionally issued. and neither receipt nor possession mereot conters or teanslers any right in, or license fo use, the subject matter of the drawing or any design or technical intormalion shown thereon, nor any right to reproduce this Grawing or any part thereof. Except for manutacture by vendors of Atari Inc., and tor manutacture under the corporation's written license. ‘no right to reproduce this drawing Is granted or the subject ma ler thereo! unless by watten agreement with or watten per sion Irom the corporation
Figure 3-13 Regulator/Audio || PCB Assembly A035435-02 G
Liberator™ Maintenance, Repair and Parts
Regulator/Audio || PCB Assembly Parts List
| Designator | Description | Part No. |
Capacitors
| C1 | 470 uF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor | 24-250477 |
| C2 | 0.001 uF, 50 V, Ceramic-Disc Axial-Lead Capacitor | 122002-102 |
| C3 | 0.1 uF, 50 V, Ceramic-Disc Axial-Lead Capacitor | 29-088 |
| C4 | 470 uF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor | 24-250477 |
| C5 | 0.01 uF, 25 V Minimum, Ceramic-Disc Axial-Lead Capacitor Acceptable substitute | 100015-103 |
is part no. 122005-103
| C6 | 0.22 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor | 122004-224 |
| C7 | 0.001 uF, 50 V, Ceramic-Disc Axial-Lead Capacitor | 122002-102 |
| c8 | 0.22 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor | 122004-224 |
| c9, C10 | 3300 uF, 35 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor | 24-350338 |
| cn | 0.1 uF, 50 V, Ceramic-Disc Axial-Lead Capacitor | 29-088, |
| C12 | 470 uF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor | 24-250477 |
| C13 | 1000 uF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor | 24-250108 |
| C14 | 0.01 uF, 25 V Minimum, Ceramic-Disc Axial-Lead Capacitor Acceptable substitute | 100015-103 |
is part no. 122005-103
| C15 | 0.22 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor | 122004-224 |
| ce | 0,001 uF, 50 V, Ceramic-Disc Axial-Lead Capacitor | 122002-102 |
| C17 | 0.22 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor | 122004-224 |
| C18, C19 | 3300 uF, 35 V, Aluminum Electrolytic Fixed AxialLead Capacitor | 24-350338 |
| C20, C21 | 0.1 pF, 50 V, Ceramic-Disc Axial-Lead Capacitor | 29-088 |
| C22, C23 | 1 uF, 50 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor | 24-500105 |
| C24 | 22 uF, 35 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor | 24-360226, |
| C31 | 22 uF, 35 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor | 24-360226 |
Diodes
| cR1 | Type-1N4002, 1 A, 100 V Silicon Rectifier Diode | 31-1N4002 |
| CR4 | Type-1N4002, 1 A, 100 V Silicon Rectifier Diode | 31-1N4002 |
| CR5-CR8B | Type-1N5401, 3 A, 100 V Silicon Rectifier Diode | 31-1N5401 |
Integrated Circuits
| Qi | Type-LM305, 5 V, Linear Voltage Regulator | 37-LM305 |
| a5 | Type-TDA2002A, 8 W, Linear Audio Amplifier Integrated Circuit | 137151-002 |
| Q7 | Type-TDA2002A, 8 W, Linear Audio Amplifier Integrated Circuit | 137151-002 |
| Qs | Type-7812, + 12 V, Voltage Regulator | 37-7812 |
| ag | Type-7905, -5 V, Voltage Regulator | 37-7905 |
Resistors
| R1 | 270 2, +5%, Vs W Resistor | 110000-271 |
| R3 | 33 Q, +5%, v4 W Resistor | 110000-330 |
| R4 | 100 2, +5%, % W Resistor | 410000-101 |
| RS | 2.7 Q, +5%, 1 W Resistor | 110009-027 |
(Continued on next page)
3-37
Maintenance, Repair and Parts Liberator™
Regulator/Audio Il PCB Assembly Parts List, continued
| Designator | Description | Part No. |
| R6 | 3.9 kQ, +5%, “4 W Resistor | 110000-392 |
| R7 | 7.5 kQ, +5%, Va W Resistor | 110000-752 |
| R8 | 1 k& Vertical PCB-Mounting Cermet Potentiometer Acceptable substitute is | 19-315102 |
part no. 119002-102
| RQ | 220 2, +5%, Vz W Resistor | 110001-221 |
| R10 | 12, +5%, % W Resistor | 110000-010 |
| R11 | 10 2, +5%, v4 W Resistor | 110000-100 |
| R12 | 100 2, +5%, 1% W Resistor | 110000-101 |
| R13, R14 | 10 kQ, +5%, 14 W Resistor | 110000-103 |
| R19 | 12, 5%, % W Resistor | 110000-010 |
| R20 | 10 2, +5%, v4 W Resistor | 110000-100 |
| R21 | 220 2, +5%, V2 W Resistor | 110001-221 |
| R22 | 100 2, +5%, %4 W Resistor | 110000-101 |
| R24 | 0.12, +3%, 7 W Wirewound Resistor | 19-100P1015 |
| R25 | 42, +5%, 5 W Wirewound Resistor | 116001-040 |
| R27, R28 | 1kQ, +5%, v4 W Resistor | 110000-102 |
| R29, R30 | 10 Q, +5%, V4 W Resistor | 110000-100 |
| R31 | 22 2, +5%, 10 W Wirewound Resistor | 116000-220 |
| R32, R33 | 5.6 kQ, +5%, 4 W Resistor | 110000-562 |
Transistors
| Q2 | ‘Type-TIP32 PNP Power Transistor | 33-TIP32 |
| Q3 | Type-2N3055 NPN Silicon Transistor | 34-2N3055, |
Mechanical Parts
| J6 | 6-Position Connector Receptacle | 79-58306 |
| J | 9-Position Connector Receptacle | 79-58308 |
| JB | 4-Position Connector Receptacle | 79-58354 |
| Jg | 6-Position Connector Receptacle | 79-58306 |
| J10 | 12-Position Connector Receptacle | 79-58346 |
Q3 #6-32 x V2-Inch Cross-Recessed Pan-Head Corrosion-Resistant Steel Machine Screw 72-1608C
| Q5 | #6-32 x ¥4-Inch Binder-Head Nylon Screw | 75-F60405 |
| QB | #6 ie yinch Cross-Recessed Pan-Head Thread-Forming Type-AB Zinc-Plated-Steel | 72-6606S |
crew
Heat Sink 034531-01 Test Point Acceptable substitute is part no. 020670-01 179051-001
3-38
Liberator™ Maintenance, Repair and Parts
H. Power Supply Assembly
A021084-xx (Voltage plugs)
29-053 (Capacitor) 034544-01 (Fuse block cover)
79-4411001 (Fuse post) 78-70501SC. (Capacitor bracket) 46-2017002 (Fuse)
A035891-02 034482. (Fuse harness assy.) }482-02 (Chassis)
46-301203 (Fuse)
037639-01 (Label)
A034630-01 (Filter Assy.)
46-2014002 (Fuses)
j ‘A035890-01 (Bushing)
73-3206 (Fuse block) 037641-01
79-15021001 (Termial block) (Power harness}
A034629-01 3A-MDA3501 (AC harness) (Rectifier)
Figure 3-14 Power Supply Assembly A037671-01 and -02 C
3-39
Maintenance, Repair and Parts Liberator™
Power Supply Assembly Parts List
Part No. Description
| A021084-01 | Voitage Plug for 100 V (90-110 VAC) | (violet wire color—plugs into J3) |
| A021084-02 | Voltage Plug for 120 V (105-135 VAC) | (yellow wire color—piugs into J3)* |
| A021084-04 | Voltage Plug for 220 V (200-240 VAC) | (blue wire color—plugs into J3) |
| A021084-05 | Voltage Plug for 240 V (220-260 VAC) | (brown wire color-—plugs into J3) |
A034629-01 AC Harness Assembly (J4A) A034630-01 RFI Filter Assembly (FL1i—designation not marked) A035888-01 Transformer Assembly (T1—designation covered) (Acceptable substitute is part no. A035888-02) A035890-01 Power Harness Assembly (J2) A035891-02 Fuse Harness Assembly (F2-F6) 29-053 27,000 uF, 15 VDC Electrolytic Capacitor (C1) 3A-MDA3501 Type-MDA 3501 Bridge Rectifier (CR1)
| 46-2014002 | 4 A, 250 V, 3AG Slow-Blow Glass CartridgeType Fuse | (F2, F4-F6) |
| 46-2017002 | 7 A, 250 V, 3AG Siow-Blow Glass Cartridge-Type Fuse | (F1) |
| 46-301203 | 20 A, 32 V, 3AG Slow-Blow Glass CartridgeTypeFuse | (F3) |
78-2708 Nylon Type 6/6 Hole Bushing with %Inch Inside Diameter x %,-Inch Outside Diameter x %4-Inch Thick 78-70501SC 2-Inch Diameter Capacitor Mounting Bracket (C1) 79-15021001 2-Circuit Single-Row Terminal Block (located under F4) 79-3206 5-Position 3AG Fuse Block with %-Inch Quick-Disconnect Terminals (F2-F6) 79-4411001 Panel-Mounting Non-Indicating 3AG Cartridge-Type Fuse Post (F1) 034482-02 Power Supply Chassis Base 034544-01 Fuse Block Cover (F2-F6) 037243-01 Metal Base Plate (not shown in illustration) 037639-01 Label for Fuse Value (F1) 03764101 Label for Fuse Values (F2-F6)
*This is the only plug provided on the North American power supply.
3-40
Glossary of Terms
Glossary
AC
ACTIVE STATE
ADDRESS
ANALOG
ANODE
AMPLIFIER
AMPLITUDE
ASTABLE Liberator™
Glossary of Terms
Alternating current; from zero it rises to a maximum positive level, then passes through zero again to a maximum negative level.
The true state of a signal. For example: The active state for START is low.
A value that identifies a specific location of data in memory, normally expressed in hexadecimal notation.
Measurable in an absolute quantity (as opposed to on or off). Examples of analog devices are volume controls, light dimmers, and stereo amplifiers.
The positive (arrow) end of a diode.
A device used to increase the strength of an applied signal.
The maximum instantaneous value of a waveform pulse from zero.
Having no normal state. An astable device will free-run or oscillate as long as operating voltage is applied. The oscillation frequency is usually controlled by external circuitry.
AUXILIARY COIN SWITCH
BEZEL
BIDIRECTIONAL Amomentary-contact pushbutton switch with a black cap. It is located on the utility panel. The auxiliary coin switch adds credits to the game without activating the coin counter.
A cut, formed, or machined retention device, such as the conical device used to mount a pushbutton switch to a control panel, or the formed device used to frame the video display screen.
Able to send or receive data on the same line (e.g., the data bus of a microprocessor). BINARY
BIT
BLANKING A number system that expresses all values by using the two digits O and 1.
A binary digit; expressed as a1 or ad.
Turning off the beam on a cathode-ray tube during retrace.
BLOCK DIAGRAM
BUFFER
BUS
CAPACITOR
CATHODE
CHIP
CLOCK
COINCIDENCE
COIN COUNTER A drawing in which functional circuitry units are represented by blocks. Very useful during initial troubleshooting.
- An isolating circuit designed to eliminate the reaction of a driven circuit on the circuits driving it (e.g., a buffer amplifier).
- A device used to supply additional drive capability.
An electrical path over which information is transferred from any of several sources to any of several destinations.
A device capable of storing electrical energy. A capacitor blocks the flow of DC current while allowing AC current to pass.
The negative end of a diode.
An integrated circuit comprising Many circuits on a single wafer slice.
A repetitive timing signal for synchronizing system functions.
Occurring at the same time.
A 6-digit electro-mechanical device that counts the coins inserted in the coin mechanism(s).
COIN MECHANISM A device on the inside of the coin door that inspects the coin to determine if the correct coin has been inserted.
Liberator™
COMPLEMENTARY Having opposite states, such as the outputs of a flip-flop.
COMPOSITE SYNC Horizontal and vertical synchronization pulses that are bused together into a single signal. This signal provides the timing necessary to keep the display in synchronization with the game circuitry.
COMPOSITE VIDEO
CREDIT
CRT
DATA
DARLINGTON
pc Complete video signal from the game system to drive the display circuitry, usually comprising H SYNC, V SYNG, and the video.
One play for one person based on the game switch settings.
Cathode-ray tube.
General term for the numbers, letters, and symbols that serve as input for device processing.
A two-transistor amplifier that provides extremely high gain.
Direct current, meaning current flowing in one direction and of a fixed value.
DEFLECTION YOKE
DIAGNOSTICS
DIODE
DISCRETE
DMA Electromagnetic coils around the neck of a cathode-ray tube. One set of coils deflects the electron beam horizontally, and the other set deflects the beam vertically.
A programmed routine for checking circuitry. For example: The self-test is a diagnostic routine.
A semiconductor device that conducts in only one direction.
Non-integrated components, such as resistors, capacitors, and transistors.
Direct memory access. DMA is a process of accessing memory by bypassing the microprocessor logic. DMA is normally used for transferring data between the input/output ports and memory. DOWN TIME
LOGIC STATE
LOGIC 0, LOW Glossary
The period during which a game is malfunctioning or not operating correctly due to machine failure.
The binary (1 or 0) value at the node of a logic element or integrated circuit during a particular time. Also called the logic level. The figures below show the voitage levels corresponding to the logic states (levels) in a TTL system.
{0 VOC to +08 VDC} GREY AREA (TRI- {+08 VDC to +2.4 VDC} STATE LEVEL) LOGIC 1, HIGH
MULTIPLEXER
NMI
PAGE
PCB {+24 VDC to +5 VDC}
A device that takes several lowspeed inputs and combines them into one high-speed data stream for simultaneous transmission on a single line.
Non-maskable interrupt. NMI is a request for service by the microprocessor from external logic. The microprocessor cannot ig- Nore this interrupt request.
A subsection of memory. A readonly memory device (see ROM) is broken into discrete blocks of data. These blocks are called pages. Each block has X number of bytes.
The abbreviation for printedcircuit board.
PHOTOTRANSISTOR A transistor that is activated by an external light source.
POTENTIOMETER
RAM
- A resistor that has a continuously moving contact which is generally mounted on a moving shaft. Used chiefly as a voltage divider. Also calleda POT (slang).
- An instrument for measuring a voltage by balancing it against a known voltage.
Random-access memory. A device for the temporary storage of data.
Glossary
RASTER-SCAN DISPLAY
RETRACE
RESISTOR
ROM A display system whereby images are displayed by continuously scanning the cathode-ray tube horizontally and vertically with an electron beam. The display system controls the intensity of the electron beam.
In a raster-scan display, retrace is the time during which the cathode-ray tube electron beam is resetting either from right to left or from bottom to top.
A device designed to have a definite amount of resistance. Used in circuits to limit current flow or to provide a voltage drop.
Read-only memory. A device for the permanent storage of data.
SIGNATURE ANALYSIS A process of isolating digital logic faults at the component level by means of special test equipment called signature analyzers. Basically, signature analyzers (e.g., the ATARI® CAT Box) convert lengthy bit streams into four digit hexadecimal sig- Liberator™
natures. The signature read by the analyzer at each circuit node is then compared with the known good signature for that node. This process continues until a fault is located.
TROUBLESHOOT The process of locating and repairing a fault.
VECTOR A line segment drawn between specific X and Y coordinates on a cathode-ray tube.
WATCHDOG A counter circuit designed to protect the microprocessor from self-destruction if a program malfunction occurs. If a malfunction does occur, the counter applies continuous pulses to the reset line of the microprocessor, which causes the microprocessor to keep resetting.
X-Y DISPLAY A display system whereby images are displayed with vectors.
ZENER DIODE A special diode used as a regulator. Its main characteristic is breaking down at a specified reverse-bias (Zener) voltage.
Liberator™ 1st printing
YOUR COMMENTS, PLEASE!
Your comments will assist Atari in improving our publications. The comments are an important part of preparing for revisions of game manuals. Please write in the space below. No postage stamp is necessary if mailed in the U.S.A.
If you have any technical questions about certain ATARI games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.
Page: Comments:
Fill in if you wish a reply:
Name.
Firm O Distributor
Address O Operator City State Zip CO Other
City State Zip CO Other.
Area Code Phone
First fold
No Postage Necessary Mf mailed in the Uniled States
be
BUSINESS REPLY MAIL 7
FIRST CLASS PERMIT NO. 1004 SUNNYVALE, CA ee POSTAGE WILL BE PAID BY ADDRESSEE
Atari, Inc. | Attn.: Field Service/Coin-Op Division P.O. Box 427 a Sunnyvale, California 94086 Ce [| [|
a Second fold — OO
wold a6pe siyy adey
YOUR COMMENTS, PLEASE! Liberator™
1st printing
Your comments will assist Atari in improving our publications. The comments are an important part of preparing for revisions of game manuals. Please write in the space below.
If you have any technical questions about certain ATARI games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.
Page: Comments:
Fill in if you wish a reply:
Name.
Firm O Distributor Address D Operator City Country O Other
City Country O Other. Phone City Code Country Code
First fold
Attach Necessary Postage
Atari Ireland Limited Attn.: Field Service/Coin-Op Division
Tipperary Town, Ireland
Second fold
wol4 eBpe sip adey
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Seller warrants that its printed-circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its video displays {in games supplied with displays) are free from defects in material and workmanship under norma! use and service for a period of thirty (30) days from date of shipment. None of the Seller's other products or paris thereof are warranted. If the products described in this manual fail to conform to this warranty, Sellers’ sole liability shall be, at its option, to repair, replace, or credit Buyer's account for such products which are
returned to Seller during said warranty period, provided:
{a) Seller is promptly notified in writing upon discovery by Buyer that said products are defective:
(p) Such products are returned prepaid to Sellers’ plant; and
- Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation or improper testing. In no event shaill Seller be liable for loss of profits, loss of use, incidental or consequential damages. Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms of this order, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller's part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products under this order.
of any non-Atari parts may void your warranty, according to the terms of the warranty. Tees CRS are ACTH ee ESE HEREC cole caroaraeauees jury to yourself and others. Be very cautious in using non-Atari-supplied components with our games, in order to insure your safety. Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories. Atari cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which ‘is performed by such distributor. This document is and contains contidential trade secret information of Atari, Inc. This document is loaned under confidential custody for the sole purpose of operation, maintenance or repair of Atari equipment and may not be used by or disclosed to any person for any other purpose whatever, and remains the property of Atari, Inc. Neither it nor the information it contains may be reproduced, used, or disclosed to persons not having a need to know consistent with the purpose of the Joan, without written consent of Atari, inc.
ATARI INC. 790 SYCAMORE DRIVE P.O. BOX 906 MILPITAS, CALIFORNIA 95035 a 408/942-3100 ¢ TELEX 35-7488 ~ ‘