720 TM-294 1st Printing
720 Degrees (rev 4) (Atari Games, 1986) · Technical Manual · 66 pages · 60 sections · original scan
Manual with
Illustrated
Parts Lists
g S © a O
Atari Games Corporation Customer Service
If reading through this manual does not lead to solving a maintenance or repair problem, call TELEHELP® at one of these Atari Games Customer Service offices:
UNITED STATES
Parts and Service
California Customer Service Office 737 Sycamore Drive P.O. Box 361110 Milpitas, CA 95035 Fax (408) 434-3945 Telex 5101007850 (Monday-Friday, 7:30-4:00 pm Pacific Time) s (408) 434-3950
EUROPE
Parts and Service
European Customer Service Office Tipperary Town, Ireland Telex 28165 (Monday-Friday, 9:00-6:00 pm GMT) Oy 0062-52155
© 1986 by Atari Games Corporation All rights reserved No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form ofa phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher. The game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the U.S. Copyright Act of 1976. This Act provides for increased penalties for violating federal copyright laws. Courts can impound infringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles. In addition, the Act provides for payment of statutory damages of up to $250,000 in certain cases. Infringers may also have to pay costs and attorneys’ fees and face an imprisonment of up to five years. Atari Games Corporation will aggressively enforce its copyrights against any infringers. We will use all legal means to immediately halt any manufacture, distribution, or operation of acopy of video games made by us. Anyone who purchases such copies risks forfeiting such a game.
Published by: Atari Games Corporation 675 Sycamore Drive P.O. Box 361116 Milpitas, California 95035
Printed in the U.S.A. 11Q 720°
720°
Notice Regarding Non-ATARI® Parts
r ~ | A WARNING A Use of non-ATARI parts or modifications of any ATARI game circuitry may adverscly affect the safety of your game, and may Cause injury t youand your players
You may void the game warranty (printed on the inside back cover of this manual) if you do any of the following: © Substitute non-ATARI parts in the game
- Modify or alter any circuits in the game by using kits or parts not supplied by Atari Games Corporation.
NOTE
This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing, device pursuant to Subpart J of Part 15 of Federal Communications Commission (FCC) Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area or modification to this equipment is likely to cause interference in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference. If you suspect interference from an ATARI® game at your location, check the following:
- Allgreen ground wires in the game are properly connected as shown in the game wiring diagram. © The power cord is properly plugged into a grounded three-wire outlet.
- The game printed-circuit boards (PCBs) are properly installed with the Electromagnetic Interference (EMI) ground plane. if you are still unable to solve the interference problem, please contact Customer Service at Atari Games Corporation. See the inside front cover of this manual for service in your area,
ith
720°
Table of Contents
Set-Up How to Use This Manual .. Inspecting the Game Control and Switch Locations Coin and Game Opiion Settings .
Game Play Introduction . Operating Modes Game Play Hints for Game Play Operator Hints .
Self-Test RAM/Interrupt/ROM Test 6502 Processor Test ..... Control Test 7 Motion Object Test....... Motion Object Height Test . Alphanumeric Test . Scrolling Playfield Test Color Bar Test... Color Purity Test .. Convergence Test. . Accounting Information . . Starting Game Time Histogram . . Add-A-Coin Game Time Histogram Reset Saved Information Screen . Coin Option Settings . . Game Option Settings . feaen ee
Wey VOWS
POE Ewe
Y Sw®UUURADREANARERLS PEE YW WL YW
Maintenance Preventive Maintenance Preventive-Maintenance Intervals . . Removing the Control Panel ..... . . Cleaning the Push Button Leaf Switches vacusne Maintaining the Rotary Control»... ee eee eee -. 42 Cleaning the Coin Mechanism ....... tree ines ' sevens 4&3 Cleaning the Interior Components Peete eee see cece 43 Corrective Maintenance... 0... eee 46 Removing the Video Display ...... . eee Lev eevee eevee . . 46 Removing the Rotary Control voces vices 47 Disassembling the Rotary Control ..... . . wees . 47 Reassembling the Rotary Control . 47 Removing the Game PCBs . . 48 Removing the Incandescent Lamp . . wade a . 4-10 Removing the Speakers ....... . . a boc 410 4-2 4.2
Troubleshooting — Troubleshooting Aids Troubleshooting Techniques .. . Soldering Techniques . . : Troubleshooting Static-Sensitive Devices. WDA SLOW
IWustrated Parts Lists See List of Illustrations that follows
720°
List of Illustrations
Figure 1-4
Figure 3-1 Figure 3-2 Figure 3-3 Figure 3-4 Figure 3-5 Figure 3-6 Figure 3-7 Figure 3:8 Figure 3-9 Figure 3-10 Figure 3-11 Figure 3-12 Figure 3-13 Figure 3-14 Figure 3-15, Figure 3-16 Figure 3-17 Figure 2.3 Figui~ 5-19 Figure 3-20 Figure 3-21 Figure 3-22 Figure 4-1 Figure 4-2 Figure 4-3 Figure 4-4 Figure 4-5
Figure 5-1 Figure 5-2 Figure 5-3 Figure 5-4
Figure 6-1 Figure 6-2 Figure 6-3 Figure 6-4 Figure 6-5 Figure 6-6 Figure 6-7 Figure 6-8 Figure 6-9 Figure 6-10
Table 1-1 Table 1-2 Table 1-3 Table 4-1 Control and Switch Locations
RAM Test Fails Imerrupt Test Fails . ROM Test Fails Reset Retry Communications Fails. Music/RAM/ROM Fails Sound Output. . Sound Status Control Test Passes Motion Object Test . Motion Object Height Test Alphanumeric Test Scrolling Playfield Test . Color Bar Test Color Purity Test. Convergence Test Accounting Information Starting Game Time Histogram Add-A-Coin Game Time Histogram . Reset Saved Information Screen , Coin Option Settings Game Option Settings . Control Panel Removal Maintaining the Rotary Control Video Display Removal Game PCB Removal . : Light and Speaker Removal ........ Removing IC (Cut-Pin Method) .... Removing IC Pins . Removing Solder from Piated- Through Holes . Removing Solder from Lead Connection Pads
Cabinet-Mounted Assemblies Control Panel Assembly Rotary Control Assembly Light and Speaker Panel Assembly . . : Switching/Linear (SL) Power Supply ‘Assembly Coin Acceptors, Inc. Coin Door Assembly Printed-Circuit Board Mounting Hardware .... Central Processing Unit (eu) P PCB Assembly . Video PCB Assembly . Audio I PCB Assembly:
List of Tables Game Specifications Coin and Credit Option Settings Game Option Senings Recommended Preventive-Maintenance Intervals . 5-4
6-10
G17 6-18
6-27
beeen Wok bw
vi
Safety Summary
The following safety precautions apply to all game operators and service personnel, Specitic warnings and cautions will be found throughout this manual where they apply 4& WARNING A Properly Ground the Game. Players may receive an ciectrical shock if this game is not properly grounded! To avoid electrical shock, do not plug in the game until it has been inspected and properly grounded. This game should only be plugged into a grounded three-wire outlet. If you have only 4 2-wire outlet, we recommend you hire a licensed electrician to install a grounded outlet. Players may receive an electrical shock if the control panel is not properly grounded! After servicing any parts on the control panel, check that the grounding wire is firmly secured to the inside of the control pane. Only then should you lock up the game. AC Power Connection. Before connecting the game to the AC power source, verify that the game's power supply is properly configured for the line voltage in your location. Disconnect Power During Repairs. To avoid clectrical shock. disconnect the game from the AC power source before removing or repairing any part of the game. When removing or repairing the video display, extra precautions must be taken to avoid electical shock because high voltages may exist within the display circuitry and cathode-ray tube (CRT) even after power has been disconnected. Do not touch internal parts of the display with your hands or with metal objects! Always discharge the high voltage from the CRT before servicing this area of the game. To discharge the CRT: Attach one end of a large, well-insulated, 18-gauge jumper wire to ground. Momentarily touch the free end of the grounded jumper to the CRT anode by sliding it under the anode cap. Wait two minutes and discharge the anode again. Use Only ATARI Parts. To maintain the safety integrity of your ATARI game, do not use non- ATARI parts when repairing the game. Use of non-ATAR! parts of other modifications to the game circuitry may adversely affect the safety of your game. and injure you or your players. Handle the CRT With Care. If you diop the CRT and it breaks, it may implode! Shattered glass can fly six feet or more from the implosion. Use the Proper Fuses. To avoid electrical shock. use replacement fuses which are specified in the parts list for this game. Replacement fuses must match those replaced in fuse type, voltage rating, and current rating. In addition, the fuse cover must be in piace during game operation.
Chapter 1
Set-Up
How to Use This Manual
This manual includes information for setting up, playing, and maintaining your 720°™ game. This manual is divided into the following chapters: \. \) \) * Chapter 1 contains set-up information. gy * Chapter 2 contains game play information. © Chapter 3 contains self-test procedures. © Chapter 4 contains preventive and corrective maintenance procedures. ent * Chapter 5 contains troubleshooting infori v\ mation. 4 = * Chapter 6 contains illustrated parts lists. yy \) Wiring and schematic diagrams for the 720° game circuitry are contained in the Schematic y Package Supplement (SP-294) included with your fj game. This chapter includes information required to set up and play your 720° game. Carefully read the information in this chapter before applying power to the game.
A WARNING A
To avoid electrical shock, do not plug in the cabinet until it has been properly inspected and set up for the line voltage in your area. This cabinet should only be connected to a grounded three-wire outlet. If you have only a two-wire Outlet, we recommend that you hire a licensed electrician to install a grounded outlet. Players can receive an electrical shock if the cabinet is not properly grounded. Do not touch internal parts of the display with your hands or with metal objects.
sertp
Inspecting the Game
A WARNING A | Do not plug, in the game until you have com- | pleted the following inspection steps |
Please inspect your 720° game carefully to cnsure that the game is complete and delivered to you in good condition. Figure 6-1 shows the locations of the component parts of the game. Table | -i lists space, power, and environmental requirements. Inspect the factory-assembled game as follows: \, Examine the exterior of the cabinet for dents, chips, or broken parts.
- Unlock and open the rear access panel. Unlock and open the coin doors. Inspect the interior of the cabinet as follows:
a. Ensure that all plug-in connectors (on the cabinet harnesses) are firmly plugged in. Do not force connectors together. The connectors are keyed so they only fit in the proper orientation. A reversed edge connector can damage a printed-circuit board (PCB) and will void your warranty, b. Ensure that all plug-in integrated circuits on each PCB are firmly plugged into their sockets. c. Inspect the power cord for any cuts or dents in the insulation.
d. Inspect the power supply. Make sure that the correct fuses are installed. Check that the harness is plugged in correctly and that the fuse block cover is mounted in place. Check that the green ground wires are connected.
e. Inspect other major sub-assemblies, such as the video display, printed-circuit boards (PCBs), speakers, and the incandescent lamp. Make sure they are
Table 1-1 Game Specifications
Characteristic Specification
Power Consumption 300 V-A, 239 W RMS Temperature +5° to +38°C (+ 37° to + 100° F) Humidity Not to exceed 95% relative 105 to 130 VAC (U.S. Games) 200 to 264 VAC (Irish Games) Line Voltage
Width 26.75 in. (68 cm) Depth 37.75 in. (95 em) Height 74.75 in. (190 cm) Weight 330 Ibs. (149 kg) 720°
mounted securely and that the green ground wires are connected.
Control and Switch Locations
Power On/Off Switch
The power on/off switch is located at the bottom rear of the cabinct. (See Figure 6-1.)
Volume Control
The volume control is located on the Audio II PCB on the inner cabinet wall opposite the upper coin door. (See Figure 1-1.) The volume control adjusts the level of sound produced by the game.
Coin Counter
The coin counter is located on the inner cabinet wall opposite the upper coin door. The coin counter records the number of coins deposited.
Self-Test Switch
The self-test switch is located on the Audio Ii PCB on the inner cabinet wall opposite the upper coin door. (See Figure 1-1.) The self-test switch selects the Self-Test Mode to check game operation. Refer to Chapter 3 for a complete description of self-test operation.
Coin and Game Option Settings
The 720° cabinet has two dual-in-line package (D!P) option switches located on the CPU printed circuit board (PCB). (See Figure 1-1.)
- The option switch at location 6/7A and switches 1 and 2 at Jocation 5/6A are for selecting coin options. © The option switches 3 through 8 at location 5/6A are for selecting all but two of the game options. Set the coin and credit option settings, and all but two of the game option settings by changing the settings of the DIP switches. Refer to Table 1-2 and Table !-3 for the available options and default (recommended) settings. To change the coin and credit settings, and al] but two of the game settings, first remove the thin film of plastic covering the option switch. Use a pen or a sharp-pointed instrument to side the appropriate small buttons to different settings. Right is the on position, and left is the off position. The rotary control and the push buttons are 7ot used to change these settings. For the procedure to change two of the game option settings, Initial Tickets and Automatic High Score Reset, re fer to Game Option Settings in Chapter 3.
mu set Up
Coin Counter Volume Control
Coin Option Switch
Audio Il PCB
Self-Test Switch
Inside Rear Wall of Cabinet Auxiliary Coin Switches
Figure 1-1 Control and Switch Locations
Set-up 720°
Table 1-2 Coin and Credit Option Settings
Settings of 8-Toggte Switch on 720° CPU PCB (at G/7A) 1 92 3 4 5 6 7 8 — Option
Coins Per Credit
| of | Off | 1 Coin 1 Credit <4 |
| Off | On | 2 Coins 1 Credit |
| On | Off | 3 Coins 1 Credit |
| On | On | 4 Coins 1 Credit |
All Coin Mechanisms
| Off | Off | Off | 1 Coin Counts as 1 Coin <4 |
| Off | Off | On | 1 Coin Counts as 2 Coins |
| Off | On | Off | 1 Coin Counts as 3 Coins |
| Off | On | On | 1 Coin Counts as 4 Coins |
| On | Off | Off | 1 Coin Counts as 5 Coins |
| On | Off | On | 1 Coin Counts as 6 Coins |
| On | On | Off | 1 Coin Counts as 7 Coins |
| On | On | On | 1 Coin Counts as 8 Coins |
Bonus Adder
| Off | Off | Off | No Bonus Adder <4 |
| Off | Off | On | 2 Coins Give 1 Extra Coin |
| off | On | Off | 4 Coins Give 1 Extra Coin |
| Off | On | On | 4 Coins Give 2 Extra Coins |
| On | Off | Off | 5 Coins Give 1 Extra Coin |
| On | Off | On | 3 Coins Give 1 Extra Coin |
| On | On | On | Free Play |
4 Manufacturer's recommended settings
Table 1-3 Game Option Settings
Settings of 8-Toggle Switch on 720° CPU PCB (at 5/6A) 1 2 3 4 5 6 7 8 Option
Ticket Levels
| Off | On | Easy (First Ticket: 3000) |
| Off | Off | Medium (First Ticket: 5000) 4 |
| On | Off | Hard (First Ticket: 8000) |
| On | On | Very Hard (First Ticket: 12,000) |
Timer for Street
| Off | On | Easy (Longest Time) |
| Off | Off | Medium <4 |
| On | Off | Hard |
| On | On | Very Hard (Shortest Time) |
Add-A-Coin Control
| Off | On | No Add-A-Coin |
| On | Off | Maximum of 1 Add-A-Coin |
| Off | Off | Maximum of 2 Add-A-Coins 4 |
| On | On | Maximum of 3 Add-A-Coins |
Start Game/Add-A-Coin Ratio
| Off | On | 1:1 (1 Credit to Start/] Credit to |
Continue)
| Off | Off | 2:1 (2 Credits to Start/1 Credit to |
Continue) <4
| On | On | 3:1 (3 Credits to Start/t Credit to |
Continue)
| On | off | 3:2 G Credits to Start/2 Credits to |
Continue)
“4 Manufacturer's recommended settings
Chapter 2
Game Play
Introduction 720°” is a one or two-player (alternating) skateboardthemed game with both competitive and street-style skating action. The player portrays the skater who performs skate maneuvers for points and competes in skate parks for medals. The action takes place in a Skate City where all surfaces are skateable. Players can choose where they wantto skate in the city, and which skate parks they want to enter, making each new game a different experience.
Game Phy
Operating Modes
720° has four operating modes: Attract, Play, High Score and Self-Test. In high score mode, there are two Top Skatables: one for Overall Score and another for Medals Score (for mest medals won in skate parks). If the pl ranks among the top 15 for either of these wo table: seconds are allowed to enter initials onto the High Score Table. Initials are sclected by using the rotary control and pressing the Kick button when the desired initial is displayed. Asin other recent Atari Games products, 720° has an Automatic Reset of High-Score feature. The table is re set to factory scores and initials every 2,000 plays but no less than 200 plays since the last player entered initials.
Game Play
At the start of each game, players can select one of iwo play modes. A training game is available for beginning players. In this game, there are numerous playing hints and messages, and the add-a-coin feature is disabled. Experienced players can start off by skating to a higher platform. Fewer game hints are given in this mode, and the add-a-coin feature is offered.
Game play starts with the player in the middle of Skate City. Using a new rotary control and a Jump and a Kick button, players maneuver around the city trying to score points by performing skillful skate moves. At various score thresholds, skate park tickets are rewarded. These tickets allow entry into one of the skate parks, where players Compete against the clock for gold, silver or bronze medals.
The player's main objective is to compete in as many skate parks as possible. In the city streets, players have a limited amount of time to win entry tickets and make their way to a skate park. In addition, there are numerous city hazards which must be avoided such as BMX riders, cars, Frisbee throwers, and other gangs. To guide the player in the city, players find map areas in streets which momentarily display the layout of the city and the location of the skate parks. In 720° there are ten class levels which determine the degree of difficulty in the skate parks and the timer in the streets. Players select the class level in which they want to compete. For instance, at the start of each game, there are four unique skate parks which are located in the outskirts of the city. Each park is a different class ranging from class 1 difficulty, which is the easiest, to Class 4 difficulty, the hardest.
In 726° players can compete in over twenty different skate parks. Each one requires unique skill moves to qualify for a medal. There are variations of a half-pipe ramp, a downhill, a slalom and a jump park. Each skate park has a distinct music score of its own, creating a different mood for players are awarded to players that ate park competition, the in the city for more street-style skatcash winnings to buy equipment skate shops which are located throughout Skating equipment helps players perform better moves. Boards give speed. Helnets allow more <-taking for successful mancuvers. Pads give faster recovery from falls. Shoes provide more height on jumps and quicker starts. As a reference for locating ¢ shops. and park entrances, players find map areas throughout the city by skating over a map. A layout of the city is momentarily displayed when players skate over a map. qualify fora medal. After cack game continues b; ing. Players can
In 720° a game ends only when piayers run out of time in the city, When the timer is running low, a SKATE OR DIE message appears along with a warning in speech When the timer runs out, killes bees appear as a final
Hints for Game Play
© Develop skill in using the rotary control in conjunction with the Jump button to do aerial moves, because they are worth more points. Press the Jump button after gaining speed, and then rotate the control in a 360degree motion. In this game, it is possible to do much more than just a 360-degree turn!
- When attempting certain aerial or rotational moves, it is important to be properly aligned on landing, otherwise the skater bails, or falls down.
- To qualify for medals in the higher classes of skate parks, it is best to try to buy some skate equipment first to allow players to perform harder moves. © Daring players should try to wait out the timer in the streets, performing skate moves and acquiring points until the timer is about to expire.
Operator Hints
Here are some pointers for maximizing earnings from your 720° game. The factory setting might need to be adjusted after the game has been on location for a long period of time or if your location does not warrant two coins per play.
Maximizing Earnings
The key to maximum earnings is striking a midpoint on game times. Initially, game times should be short enough
720"
to allow higher player turnover. At the same timc, game times must be long enough to give the player good value and ensure continued repeat play. 720° has a comprehensive statistics and coin accounting package which is described in detail in Chapter 3 of this manual. To find out whether or not your players are getting adequate value for their money, you should evaluate the following information,
Average Game Times There are two averoge game times listed on the Accounting information screen in the Self-Test Mode. One reading indicates Average Starting Game Time which shows average times per credit for all starting games only. The other reading, Average Add-a-Coin Game Time, represents average times per credit only for games played using the game continuation feature. If the game is set at factory-recommended settings, initially the Average Starting Game Time should be between 2:00 and 2:30 minutes. On factory settings, two credits are required for game start, and one credit for game continuation. The Average Starting Game Time, however is not tied into the number of credits required for game start. Therefore, it is accurate even if you have changed the option setting to one credit to start. Ifthe Average Starting Game Time is not in the range of 2:00 to 2:30 minutes, refer to the Histogram scrcens. 720° has two histogram screens representing the distribution of game times in 30-second increments. Be sure to refer to the Histogram screen for Starting Game Times. Ifa high percentage of game times are under 1:30 (for example, over 40% of total coins collected), the game might be too difficuit for the particular location. Game option settings should be adjusted by changing the Timer for Street setting one level easier. If game times are still too short after one or two weeks, try changing the Ticket Levels sciting to one level easier, in addition to leaving the Timer for Street option at the easier setting. Conversely, if a high percentage of your Average Starting Game Times are over 1:30, the current settings might be too easy. In this case, the Timer for Street setting should be adjusted to one level harder. Again, if game times are not affected, an additional setting change might be required by making the Ticket Levels setting one level harder.
The histogram data in 720° will show a small percentage of players who can play the game for over 5:00. Atari Games research has shown that this is a positive factor in the long-term appeal of a game, as long as the number of longer games represents only a small percentage of the total.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Chapter 3
Self-Test
This game tests itself and provides visual and audible indications of the condition of the game circuitry and controls. Self-test information is displayed on the screen and sent through the sound system. No additional equipment is required. We suggest that you perform a self-test when you first set up the game, each time you collect the money, or when you suspect game failure. Coin and game option settings are displayed in the Self-Test Mode. Sixteen self-test screens provide a visual and audible check of the 720°™ game circuits. Refer to Figure 1-1 for the self-test switch location, The Self-Test Mode can be entered immediately after turning on the game power, either from the Play Mode or from the Attract Mode. If the self-test switch is turned on during the Play or the Attract Mode, the first display to appear is the Accounting Information. By pressing the Kick button, the self-test advances to the Control Test. The self-test then advances from the Control Test to the end. The gare power must be turned off, the self-test switch turned on, and the game power turned on again to start the self-test with the RAM/ Interrupt/ROM Test. The following self-test procedure is presented in the sequence in which the self-test screens appear when the self-test switch is turned on and then the game power is turned on. Turning off the self-test switch at any time during the self-test causes the game to return to the Attract Mode.
sell Test
RAM/Interrupt/ROM Test The RAM/InterrupUROM ‘Test screens are shown in Figures 3-1 . and 3-3. These sereens display the failure information for the RAM. interrupt, and program: ROM circuitry on the CPU and Video PCBs. If the RAM/InteryupUROM test passes. the display advances to the 6502 Processor Test The RAM test checks the condition of the T-1 1 microprocessor RAM, zero page RAM, motion object RAM, playfield RAM, alphanumeric RAM, and associated circuitry located on the Video PCB. If the RAM test fails, an error message gives the location of the failed RAM or associated circuitry on the Video PCB as shown in Figure 3-1. If the zero-page RAM or associated circuitry fails, the screen turns red and the address location of the failed component flashes continuously to facilitate troubleshooting.
Figure 3-1 RAM Test Fails
SCINTERRUPT FAILURE
Figure 3-2 interrupt Test Fails
a2 720°
Figure 3-3 ROM Test Fails
After the RAM test passes, the interrupts on the CPU and Video PCB are checked. Ifthe interrupt test fails, an error message as shown in Figure 3-2 can appear on a green sereen, which indicates a possible vertical-blanking or interrupt-logic failure. After the interrupt test passes, all eight of the program ROMs on the CPU PCB are tested for check sums. If the ROM test fails, an error message gives the location of the failed ROM or associated circuitry as shown in Figure 3-3.
6502 Processor Test The 6502 Processor Test screen provides visual and audible information to indicate the condition of the 6502 sound microprocessor and associated circuitry, All functions of the sound microprocessor are checked including: RAM/ROM, interrupts, music synthesizer, and soundeffects processor. Basic communication between the T-11 (master) and the 6502 (slave) microprocessors is also checked.
The 6502 test starts with a reset/communications check that first resets the 6502 and then checks for proper response to Start up protocol. This test checks the communications ports (T-11 to 6502 and 6502 to T-11), the 6502 reset circuit, and the general condition of the 6502. If the 6502 circuitry does not respond properly to the reset, the system retries the reset procedure ten times Then an error message and retry count number is displayed as shown in Figure 3-4 If the 6502 circuitry fails to reset through ali ten attempw, a communications error message is displayed as shown in Figure 3-5. If the reset/communications check passes, then the condition of the 6502 microprocessor, RAM, ROM, interrupts, music (Yamaha) synthesizer, and associated cir-
720°
6502 PROCESSOR. TEST
COMM. FAELURE... 8
PRESS RICK BU ELON LO CONTINUE
Figure 3-4 Reset Retry
02 PROCESSOR TEST
COMMUNICATIONS FALE
PRESS KICK BE LEON TO CONTINUE
Figure 3-5 Communications Fails
cuitry is checked. If one or more of these circuits fails, an error message is displayed as shown in Figure 3-6. If the RAM, ROM, and music synthesizer check passes, then the music (Yamaha) synthesizer, and sound-effects generator (POKEY) sound outputs are checked. As each of these three tests is run, an appropriate message is displayed as shown in Figure 3-7.
- YAMAHA TEST consists of eight tones in a major scale that alternate between left and right sound channels (16 tones total). © L. POKEY TEST consists of four tones in a major chord that come from the left sound channel. © R POKEY TEST consists of four tones ina major chord that come from the right sound channel. After the three sound output tests are completed, the sound status messages are displayed as shown in Figure 3-8 Self-Test
6502 PROCESSOR TEST
SS KICK BL EEON LO CONTINUE
Figure 3-6 Music/RAM/ROM Fails
6502 PROCESSOR’ TEST
. POKEY TEST
PRESS KICK BU EEON LO CONTINUE
Figure 3-7 Sound Output
- NUMBER OF SOUNDS is the total number of sounds used in the 720° game.
- CURRENT SOUND is the current sound selected for playing. Press the Jump button to select the sound numbers indicated by the CURRENT SOUND message shown in Figure 3-8. Turn the rotary control to sequence through the selected sounds.
The sound status screen also indicates the condition of the left and right coin switches. Press the left and right coin switches, and check the screen for a corresponding LEFT COIN and RIGHT COIN message. (See Figure 1-1 in Chapter 1 for the switch locations.)
Press either Kick button to obtain the next screen.
Self-Test
6502 PROCESSOR. TEST
NUMBER CF SOUNDS: 47 CURRENT SOUND: ae
LEFT COIN
Figure 3-9 Control Test Passes
Control Test The Rotary Control Test screen is shown in Figure 3-9. The control test checks the rotary control, or rotating skater control, and the Jump switch. (It is assumed that the Kick switch works since it must be functioning to get to this test.) First, the zeroing function of the control is checked. This function gives the control a point of reference for determining direction. Rotate the control clockwise slowly until the ZEROED message is displayed in the center of the test circle. This should occur when the control is at the top, or closest to the video display screen. Then release the control. The test then requires a counterclockwise rotation. (If the control is notat the top, you will be asked to put itin this position.) As the control turns, the on-screen boxes corresponding to the control's position should fill in. If the control is 720°
rotated too quickly, some boxes will be missed, Once all the boxes have been filled, a DONE message is displayed in the center of the circle. The test then repeats this procedure for a clockwise rotation. (Again, if the control is notat the top, you will be asked to put it in this position.) After completing the clockwise rotation procedure, the test returns to a counterclockwise rotation and repeats. At any time during the test, pressing the Jump switch causes a /UMP SWITCH message to be displayed as long. as the switch is held down. Press either Kick button to obtain the next screen.
Motion Object Test
The first Motion Object Test screen is shown in Figure 3-10. This test indicates the motion object horizontal and vertical display locations, motion-object color palettes, and checks the motion/playfieid prioritizing logic circuit. The Motion Object Test screen should show 39 motion objects and four colored boxes (numbered 0 through 3). The left two boxes (0 and 1) should be red, and the right two boxes (2 and 3) should be green, The motion objects should be colored (from left to right) blue, light blue, purple, and white. Any error in color can indicate a problem with the color palette select circuits. Turn the rotary control to control the direction of the scroll. Hold the Jump button to scroll. Press the Jump button to select the next motion object. Note that the currently displayed motion object moves correspondingly. Move the motion object across the four colored boxes. Note that the motion object moves bebind the red boxes and in front of the green boxes. Press the Jump button to select the next motion object and repeat the preceding procedure. Press either Kick button to obtain the next screen.
MOTION OBJECT TEST
(ORJECT. NUMBER: 07 PRESS KICK BEE EON FOOCONTEINUE
Figure 3-10 Motion Object Test
720°
Motion Object Height Test The Motion Object Height Test screen is shown in Figure 3-11. This test indicates the condition of the motion object height circuit and the horizontal load disable circuit Each successive column of motion objects should be 16 pixels taller than the last. The top 16 pixels of each column should be the same. Each column should add anew 16x 16 pixel stamp picture to the bottom and slide the previous one up by 16 pixels. Turn the rotary control to control the direction of the scroll. Hold the Jump button to scroll, Press the Jump button to obtain a new set of motion objects. Press either Kick button to obtain the next screen.
Alphanumeric Test The Alphanumeric Test screen is shown in Figure 3-12. This screen indicates the condition of the alphanumeric ROM, alphanumeric color palettes, and associated circuitry, This screen shows eight lines of alphanumeric characters, the top four lines with large characters and the bottlom four lines with small characters. Each line should be displayed in a different color. Press either Kick button to obtain the next screen.
Scrolling Playfield Test
The Scrolling Playfield Test screen is shown in Figure 3-13. This screen indicates the condition of the piayfieid ROM, playfield display circuits, and playfield color palettes. The display in Figure 3-13 shows the central square of Skate City, Turn the rotary control to contro} the direction of the scroll. Hold the Jump button to scroll.
MOTION OBJECT HEIGHT TEstT
PRESS KICK BUT EON LO CONTINUE
Figure 3-11 Motion Object Height Test Self-Test
ALPHASTEST OERBGAR ERAS BESRRRRR AB ht EMENSOR BOR ESET]
ApcoRr oN 4s KLMNDPORST UvuNezEtae
PRESHERECK BUT TON<TO"CONTENUE
Figure 3-12 Alphanumeric Test
Figure 3-13 Scrolling Playfield Test
Press either Kick button to obtain the next screen.
Color Bar Test
The Color Bar Test screen is shown in Figure 3-14. This test indicates the condition of the color RAM, video amplifiers, and associated circuitry. Sixteen vertical grey-scale bars and three groups of sixteen vertical bars with shades of red, green, or blue are displayed. The brightest bar should be on the left and darkest (black) bar on the right, with a black frame around the screen. Each group of red, green, or blue should be Split in half horizontally to show two fade scales. Each upper fade scale is ranged by changes in overall intensity (Z) and each lower fade scale by individual color intensity {R, G, B). This test helps to determine if white tracking is set properly (grey-scale bars range from white to grey),
Selt-Test
PRESS KICK BL LTON FO CONTINUE
Figure 3-14 Color Bar Test
D
PRESS KICK BE ELON LO CONTINUE
Figure 3-15 Color Purity Test
Refer to the white tracking procedure in the video display manual if adjustment is required. Press either Kick button to obtain the next screen
Color Purity Test The Color Purity Test consists of five color displays that indicate the condition of the display color-purity circuits. The first display to appear should be a red screen with the word RED displayed at the top of the screen as shown in Figure 3-15. Also included on all of the color purity screens are smail elbow-shaped characters at the four corners of the screen. These characters are used for screen and alignment adjustments. Press the Jump button, and the next display to appear should be a green screen with the word GREEN displayed at the top of the screen. Press the Jump button to obtain a blue, white, and finally a grey screen. After the grey screen, the display repeats this sequence
3-6 +20"
lf the display characteristics are not correct, refer to the video display manual for the color-purity adjustment procedure or the possible cause of failure. Press either Kick button to obtain the next screen
Convergence Test The Convergence Test screen is shown in Figure 3-16. This test indicates the condition of the display size, centering, linearity, and convergence. Initially, a white-dot convergence pattern is displayed. Convergence between any two colors should not exceed 0.7 mm in the middle of the screen and 1.2 mm in the corners.
Press the Jump button to obtain a violet pattern for adjusting, the red-to-blue convergence. Pressing the Jump button again displays a green pattern, and then the sequence is repeated This pattern can also be used to adjust screen size, centering, and brightness (black level). To obtain the proper screen size, overscan of adjust the pattern to be larger than the face of the CRT: all four pattern corners should be just beyond the corners of the CRT. After adjusting the screen size, check the game playfield in the two-player mode: verify that the score information for both players is on the screen. Press either Kick button to obtain the next screen.
Accounting Information The Accounting Information is shown in Figure 3-17. This screen provides a visual check of the current game statistics. The statistics information is accumulated either from the first time the game was turned on or from the last time the statistics were reset. The following game statistics appear on the Accounting, Information screen: © LEFT COINS shows the total number of coins deposited in the left coin mechanism.
Figure 3-16 Convergence Test
720°
TOTALLY CAME:
Figure 3-17 Accounting Information
RIGHT COINS shows the total number of coins deposited in the right coin mechanism. ADD A COIN shows the total number Of times a game was continued using the add-a-coin feature. ONE PLAYER GAMES shows the total number of games that were played with one player only. TWO PLAYER GAMES shows the total number of games that were played with two players. TOTAL GAME TIME shows the accumulated time of all one- and two-player games played in hours, minutes, and seconds.
TOTAL ON TIME shows the total time in hours, minutes, and seconds that the game has been turned on,
AVERAGE STARTING GAME TIME shows the total game time of all starting games divided by the total number of plays in hours, minutes, and seconds. AVERAGE ADD A COIN GAME TIME shows the total game time of all continued games divided by the total number of add-a-coin plays in hours, minutes, and seconds. °
The game statistics are accumulated from the first time the game is turned on or from the last time the statistics were reset.
Press either Kick button to obtain the next screen.
Starting Game Time Histogram The Starting Game Time Histogram screen is shown in Figure 3-18. This screen shows the distribution of times. for starting games. These times ate measured from game Start to first add-a-coin, or from game start to game end if no coin is added. The number of games in each category is indicated numerically and as a bar graph. Self-Test
QARaeeGousacodaase
Figure 3-18 Starting Game Time Histogram
Figure 3-19 Add-A-Coin Game Time Histogram
Add-A-Coin Game Time Histogram
The Add-A-Coin Game Time Histogram screen is shown in Figure 3-19. This screen shows the distribution of times for Add-A-Coins. These times are measured from the time a coin is added until the next coin is added or the game ends. The number of games in each category is indicated numerically and as a bar graph Press either Kick button to obtain the next screen.
Reset Saved Information Screen
The Reset Saved Information screen is shown in Figure 3-20. This screen resets the high score table and the accounting information to the factory settings. Use the following procedure to reset these items:
3-7
Self-Test
Figure 3-20 Reset Saved Information Screen
Figure 3-21 Coin Option Settings
- Turn the rotary control to select the item to reset.
- Press the Jump button to change the NO message to YES.
- Press either Kick button to reset the selected tables. After a brief PLEASE WAIT message is displayed, the self-test automatically advances to the next screen.
Coin Option Settings The Coin Option Settings screen is shown in Figure 3-21. This screen indicates the current coin and credit option settings of the two dual-in-line package (DIP) switches at locations 6/7A and 5/6A on the CPU PCB. The option switches at location 6/7A and switches 1 and 2 of the option switches at location 5/6A are used for selecting the coin and credit options. 720°
Set the coin and credit option seitings by changing the settings of the DIP switches located on the CPU PCB. Refer to Tables 1-2 and 1-3 in this manual for the available options and default (recommended) settings. To change these settings, first remove the thin film of plastic covering the option switch. Use a pen or a sharppointed instrument to slide the appropriate small buttons. to different settings. Right is the o77 position, and left is the off position, The rotary control and the push buttons are not used to change these settings. Press either Kick button to obtain the next scrcen.
Game Option Settings The Game Option Settings screen is shown in Figure 3-22. This screen shows the current game option settings. The first three options listed under DIP Switch Options indicate the settings of switches 3 through 8 of the DIP switch at iocation 5/6A on the CPU PCB. These switches 3 through 8 are used to select the game options, Refer to the previous section for the procedure for selecting these options. Two game options, Initial Tickets and Automatic High Score Reset, listed under EEROM Options can be changed only from this screen. To change either of these options, turn the rotary control until the arrow on the screen points to the option to be changed. Then press the Jump button to step through the possible values for the option. Each of these options retains the selected value after exiting from the screen. The factory-recommended settings for these options are: 0, 1 <4, 2,3 Yes “4, No Initial Tickets Automatic High Score Reset at 2000 Plays Press either Kick button to return to the 6502 Processor Test.
pIP SWITC FIRST BONU TIMER FOR STREET: MED MAXIMUM ADD. A. COINS:
M OPTIONS ETS: 1¢ CORE RESET:
Figure 3-22 Game Option Settings
Chapter 4
Maintenance
This chapter includes preventive and corrective maintenance procedures for the 720°™ garne components that are subject to the most use. ‘To assure maximum troublefree operation from this game, we recommend that preventive maintenance be performed as described in this chapter. Removal, disassembly, reassembSy, and replacement procedures are provided for components that might require corrective maintenance. Appropriate references are provided to Chapter 6, Illustrated Parts Lists, to aid in locating the parts of this game that are mentioned, but not illustrated, in the maintenance procedures.
Maintenance 720°
Preventive Maintenance
Preventive maintenance includes cleaning, lubricating, and tightening hardware. How often preventive maintenance is performed depends upon the game environment and frequency of play. However, for those components listed in Table 4-1 Preventive-Maintenance Intervals, we recommend that preventive maintenance be performed at the intervais specified.
Preventive-Maintenance
Intervals The preventive-maintenance intervals specified in Table 4-1 are the recommended minimum requirements for the components listed.
A WARNING A
To avoid possible electrical shock, turn off the game before performing any maintenance procedures.
Removing the Control Panel
Perform the following procedure to removelreplace the control panel. (See Figure 4-1.)
- Unlock and open the coin door on the front of the cabinet. nN . Carefully reach up through the top coin door opening and release the spring-draw latches located under the control panel on both sides of the cabinet.
- Use a 5/32-inch Allen wrench to remove the screw securing the front of the control panel to the cabinet.
- Grasp the rotary control and gently lift until the bottom edge of the control panel clears the cabinet.
- Stand the control panel on its back edge by placing it in the wood slots located under the control panel on each side of the cabinet. The panel is now in position for servicing the \eaf switches or rotary control.
- If you need to remove the control panel, disconnect the rotary control harness connector and the two PCB
Table 4-1 Recommended Preventive- Maintenance Intervals
Inspect weckly, lubricate, and tighten hardware at least every three months Inspect whenever you collect coins. Clean at least every three months. Rotary Control
Coin Mechanism
4.2 Assembly harness connectors. Remove the control panel from the cabinet. Replace the control panel in the reverse order of removal.
Cleaning the Push Button Leaf
Switches
Perform the following procedure to clean the leaf switch contacts and tighten the securing hardware.
- Follow the procedure described in the preceding steps 1-8 for removing the control panel.
- Use electrical contact cleaner to clean the contacts. Do not burnish them. When the push button is pressed, the wiping action of the cross-bar contacts provides a self-cleaning feature.
- Using a 15/16-inch open-end wrench, tighten the stamped nut securing the push button leaf switches to the control panel.
Maintaining the Rotary Control Preventive maintenance on the rotary control consists of:
© Inspecting the rotary control housing for excessive wear or dirt.
Inspecting the Dual Optical Coupler PCB Assembly for damage. Lubricating the friction-producing surface of the area surrounding the roller in the upper housing and the roller itself, the lower ball in the bearing housing, and the chain in the encoder disc shield area.
- Replacing or tightening the securing hardware if necessary. Perform the following procedure to lubricate and tighten the rotary control. (See Figure 4-2.)
- Open the control panel as previously described.
- Disconnect the harness connectors from the Dual Optical Coupler PCB Assembly.
- Using a 3/8-inch nut driver, remove the four hex nuts holding the rotary control assembly to the control panel
720°
Rotary Control
Screw
Coin Door Hamess Connector Maintenance
Spring Draw Latch
Figure 4-1 Control Panel Removal
- Apply a chain lubricant (Atari part 10. 107028-001) to the chain,
- Disassemble the rotary control as described in Disassembling the Rotary Control later in this Chapter to gain access to the lubrication points.
- Apply lithium grease (Atari part no. 107027-001)to the roller and the lower ball of the control handle.
- Apply a film of light oil (Atari part no. 107013-001) to the pivot arm attached to the bottom housing plate.
- Apply a chain lubricant (Atari part no. 107028-001) to the chain.
- Reassemble the rotary control. Reconnect the harness connectors to the PCB Assembly.
- Using a 3/8-inch nut driver (or an appropriate tool), tighten the hex nuts holding the rotary control assembly to the control panel.
Cleaning the Coin Mechanism
Use a soft-bristled brush to remove loose dust or foreign material from the coin mechanism. A toothbrush can be used to remove any stubborn build-up of residue in the coin path. After cleaning the coin mechanism, blow out all of the dust with compressed air.
Cleaning the Interior
Components
Perform the following procedure to clean the components inside the cabinet.
A WARNING A
Turn off the game power, but do not unplug the | power cord before cleaning inside the cabinet. The power cord provides a ground path for stray static voltages that can be present on the cleaning, | tools. |
1, Unlock and open the rear access door.
- Discharge the high-voltage from the cathode-ray tube (CRT) before proceeding. The display assembly con-
* oe
Maintenance
A Lithium Grease
a Light O11
#4-40 x Y2-in. Pan-Head Screw:
Bottom Housing Plate —_ #1032 x%«In. Cap Screw
PCB Bracket Encoder Dise Shield UA! Opt. Cpl. PCB Assy
Nylon Washer
Chain Lubricant
Lo Wave Washer
‘Chain Modified Sprocket
Nylon Washer
‘Sprocket
Etched Encoder Retaining Ring Encoder Disc Mounting Plate
Centering Disc Spacer
‘Centering Disc
#4 Flat Washer
@<—————— #4 Lock Washer / fe 44.40. 41n. Pan-Head Screw
Figure 4-2 Maintaining the Rotary Control = 29°
Pivot Arm ™ /
#10 Lock Washer
Nylon Washer
Bearing Housing aa (‘-piece assy.) #8 Lock Washer
'#8-32 x ¥4-In. Cap Screw
‘Sprocket Post
Yeln, Dia. x Y-In. Spring Pin
720° Maintenance
Disc
{Lithium Grease
Roller Retaining Ring
Upper Housing
{ Lithium Grease
Pivot Ball
Bushing Lower Bail
Lower Housing
Bottom Housing \ y, J Lithium Grease
#8 Narrow Flat Washer
Ja #8-16 x 1%-In. Pan-Head Screw
Figure 4-2 Maintaining the Rotary Control, Continued
Mai intenance
tains a circuit for discharging the high voltage to ground when power is removed. However, to make certain, aways discharge the display as follows. a. Attach onc end ofa large, well-insulated, 18-gauge jumper wire to ground. Momentarily touch the free end of the grounded jumper to the CRT anode by sliding it under the anode cap.
c. Wait two minutes and repeat part b.
. Use a vacuum cleaner with a soft long-brisded brush attachment or use a soft-bristled paint brush to remove loose dirt and dust accumulated on the inside of 720°
the cabinet. Be sure to clean the electrical components thoroughly (power supplies, PCB assemblies, display, etc.)
Corrective Maintenance
Corrective maintenance consists of removal, disassembly, reassembly, and replacement of game components. The fol lowing procedures are provided for components that may require corrective maintenance.
Removing the Video Display
Perform the following procedure to remove/replace the video display. (See Figure 4-3.) 1. Turn the game power off and wait two minutes. Unpiug the power cord. . Use a 1/8-inch hex driver to remove the three screws securing the glass retainer to the cabinet.
Glass Retainer x
a Display Shield Detail Cleat 3.
rg
Video Display Grasp the display shield on the top edge and gently pull it out from the cabinet. . Use a flat-head screwdriver to remove the staples, if any, securing the bezel to the cabinet. Remove the bezel.
. Use a Phillips screwdriver to remove the four screws securing the detail cleat to the cabinet. Remove the cleat. . Use a Phillips screwdriver to remove the four screws securing the display rear access panel. Remove the panel, . Unlock and open the rear access door.
Figure 4-3 Video Display Removal
720°
A WARNING A
High Voltage The video display contains potentially lethal high voltages. To avoid injury, do not attempt to setvice this display until you observe all precau- | tions necessary for working on high-voltage equipment. X-Radiation The video display has been designed to minimize X-radiation, However, to avoid possible exposure to soft X-radiation, never modify the highvoltage circuitry, Implosion Hazard The cathode-ray tube may implode if struck or dropped. Shattered glass may cause injury within a G-foot radius. Use care when handling the display.
- Discharge the high-voltage from the cathode-ray tube (CRT) before proceeding. The display assembly contains a circuit for discharging the high voltage to ground when power is removed. However, to make certain, always discharge the display as follows. a. Attach one end ofa large, well-insulated, 18-gauge jumper wire to ground. b. Momentarily touch the free end of the grounded jumper to the CRT anode by sliding it under the anode cap. c. Wait two minutes and repeat part b.
- From the back of the cabinet, disconnect all the upper cabinet harness connectors. Pull these harnesses down into the lower cabinet area.
- From the front of the cabinet, use a Phillips screwdriver to remove the six screws and washers securing the display to the cabinet. il. Carefully slide the display out through the front of the cabinet.
- Replace the video display in the reverse order of removal.
Removing the Rotary Control
Perform the following procedure to remove/replace the rotary control. (See Figure 4-2.) Maintenance
1, Open the control pancl as described under Preventive Maintenance,
- Disconnect the harness connectors from the Dual Optical Coupler PCB Assembly.
- Using a 3/8-inch nut driver, remove the four hex nuts holding the rotary control assembly to the control panel
- Lift the rotary control assembly out of the control panel.
wa Replace the rotary control in the reverse order of removal. Reconnect the harness connectors to the PCB Assembly.
Disassembling the Rotary
Control
Perform the following procedure to disassemble the rotary control assembly. (See Figure 4-2.)
- Disconnect the harness connectors from the PCB Assembly.
- Using a 3/8-inch nut driver (or appropriate tool), remove the four hex nuts holding the rotary control assembly to the control panel
- Using a Phillips screwdriver, remove the four screws holding the encoder disc shield to the bottom housing plate. Remove the shield.
- Using a Phillips screwdriver, remove the two screws holding the PCB Assembly to the PCB bracket.
wn . To remove the chain from its sprockets, use a 5/32inch Allen wrench to remove the screw and washer holding the sprocket to the sprocket post.
- Using a 9/64-inch Allen wrench, loosen the two cap screws through the side openings of the centering disc spacer. Remove the etched encoder assembly from the shaft. :
- Using a 9/64-inch Ailen wrench, remove the four cap screws holding the bottom housing plate to the bottom housing. Remove the housing plate.
Reassembling the Rotary
Replace the rotary control parts in the reverse order of removal. When reassembling the rotary control, check the following items:
- Be sure that the control handle is oriented toward the F orientation mark located on the underside of the lip of the upper housing assembly.
Maintenance
Be sure that the orientation for the etched encoder disc assembly is correct for reassembly. Orient the two cap screws so that one is at the 9-o'clock position and the other at the 12-0’clock position in relation to the PCB Assembly. Each serew head should be seen through the side opening of the disc spacer. Be sure to position the spring pin in the sprocket post so that the chain has enough slack to allow the handle to rotate freely.
Removing the Game PCBs
Per! form the following procedure to remove/replace the game PCBs.
CAUTION
Do not attempt to remove the CPU and Video PCBs while they are connected together. If you are going to remove both of these PCBs, remove the Video PCB first to avoid damaging the PCBs or the edge connectors.
Video PCB
Perform the following procedure to remove/replace the Video PCB. (See Figure 4-4.) 1.
2, Turn the game power off. Unlock and open the lower rear access panel, Remove the four thumb nuts holding the EMI cover to the ground plane. . Disconnect the harness connectors from the bottom of the Video PCB.
. Remove one of the two thumb screws and spacers holding the top of the Video PCB (and the bottom of the CPU PCB) to the ground plane. Loosen, but do not remove, the other thumb screw.
6.
MI Remove the two thumb screws hoiding the bottom of the Video PCB to the ground plane. Carefully hold the Video PCB in place to prevent the PCB from falling or causing excessive bending at the edge connector.
Remove the remaining thumb screw and spacer that was loosened in step 5. Gently disconnect the Video PCB from the CPU PCB. 720°
Replace the Video PCB by first connecting the Vidco PCB to the CPU PCB edge connector. Carefully position both the Video and CPU PCBs so that the holes (in the bottom of the CPU PCB and at the top of the Video PCB) are aligned. Partially install one thumb screw and spacer through both of the PCBs and into the corresponding ground plane post Install and tighten the two thumb screws holding the bottom of the CPU PCB to the ground plane. . Install the remaining thumb screw holding the top of the Video PCB (and bottom of the CPU PCB) to the ground plane Finger-tighten both thumb screws holding the top of the Video PCB (and bottom of the CPU PCB) to the ground plane. Connect the harness connector to the bottom of the Video PCB.
CPU PCB Perform the following procedure to remove/replace the Central Processing Unit (CPU) PCB. (See Figure 4-4.)
Turn the game power off. . Unlock and open the lower rear access panel. Remove the four thumb nuts holding the EMI cover to the ground plane. . Disconnect the harness connectors from the left edge of the CPU PCB. Remove the four thumb screws holding the CPU PCB (and the top of the Video PCB) to the ground plane. . Gently disconnect the CPU PCB from the Video PCB.
720°
CPU Printed-Circuit Board
Edge Connector
Spacers (2 places)
Thumb Nuts (4 places)
EMI Cover Maintenance
Ground Plane
Video PCB
Figure 4-4 Game PCB Removal
- Replace the CPU PCB by first connecting the CPU PCB to the Video PCB edge connector. Carefully position both the CPU and the Video PCBs so that the holes (in the bottom of the CPU PCB and at the top of the Video PCB) are aligned. Partially install one thumb screw and spacer through both of the PCBs and into the corresponding ground plane post.
- Install and tighten the two thumb screws holding the top of the Video PCB to the ground plane.
- Install the remaining thumb screw holding the bottom of the CPU PCB (and the top of the Video PCB) to the ground plane.
. Finger-tighten both thumb screws holding the bottom of the CPU PCB (and the top of the Video PCB) to the ground plane.
. Connect the harness connectors to the left edge of the CPU PCB. (See Figure 4-4 for the proper connector locations.)
Mamtenanee 720°
Removing the Incandescent 2. From the front of the cabinet, using a 1/8-inch hex driver, remove the eight screws holding the light and Lamp speaker grille to the top of the cabinet. Perform the following procedure to remove/repiace the 3. Using a Phillips screwdriver, remove the six screws incandescent lamp. (See Figure 4-5.) holding the front of the light and speaker panel to the cabinet. I. Turn the game power off. F. . . 4. Disconnect the speaker harness assembly.
- From the front of the cabinet, using a 1/8-inch hex driver, remove the eight screws holding the light and speaker grille to the top of the cabinet. 5, Remove the light and speaker panel
- To remove the incandescent lamp, unscrew the lamp CAUTION and remove it from the socket Do not touch the speaker cones when handling
- To remove the entire lamp fixture, disconnect the the speakers. The cone material is fragile and can light harness connector in the rear of the cabinet. Us- be casily damaged. ing a screwdriver, remove the two screws holding the lamp base and lift the base out of the front of the cabinet. Replace the lamp fixture in the reverse order of 6. removal Using a Phillips screwdriver, remove the four screws holding the speaker to the cabinet. Do not let the speaker fall.
- Lower the speaker just far enough to disconnect the Removing the Speakers two speaker wires. Ensure that the speakers are prop- . erly phased by placing the same color-coded connecwoe the aa Procedure to remove/replace the tor on the same tab on each speaker. speakers. (See Figure 4:5.) 8. Replace the speaker in the reverse order of removal
- Turn the game power off.
incandescent Lamp
Lamp Receptacle
Light & Speaker Pane!
Light & Speaker Grille Assy
Screw Speaker
Figure 4-5 Light and Speaker Removal
4.10
Troubleshooting
The information in this chapter discusses troubleshooting aids and techniques to assist the service technician when trouble is suspected in a game. Most troubles can be located quickly by following the information in this chapter. However, if problems persist, contact your local distributor or your Atari Games Corporation Customer Service Office, listed on the inside front cover of thismanual, for assistance.
Troubleshooting
Troubleshooting Aids
‘Troubleshooting aids are provided throughout this manual and the schematic package supplement. The following information is intended to acquaint the service technician with the portions of these documents that contain useful troubleshooting and repair information.
Assembly and Component Locations
The parts lists in Chapter 6 of this manual illustrate the locations of assemblies and components. Printed-circuit board (PCB) illustrations aid in rapidly locating components shown on the corresponding schematic diagram(s).
Diagrams The schematic package supplement for this manual contains schematic diagrams with component locations, active component type numbers, and electrical values.
Troubleshooting Techniques
A WARNING A
To avoid electrical shock, turn off the game power before attempting to troubleshoot this game.
The following troubleshooting steps are arranged in a sequence recommended for locating a defective component. The procedure begins with a check of the simple trouble possibilities and progresses to more extensive procedures for localizing the problem to an assembly or major circuit, and then to a defective component.
Check Fuses
Check for open fuses. Refer to the power supply parts list in Chapter 6 and to the display manual for the location and rating of each fuse used in this game. Make sure that replacement fuses are the proper type and rating.
Check Power-Supply Voltages Improper operation of all circuits usually indicates a power supply problem. Be sure that the proper line voltage is available to the power supply. Refer to the label on the power supply for its voltage rating.
Localize Trouble
Determine the trouble symptom. Use the wiring diagrams in the schematic package supplement to determine which assemblies or major circuits could cause the trouble. Perform the self-test procedure provided in Chapter 3 of this manual. 720°
Visual Check
Visually check for obvious problems in the portion of the game where the trouble is suspected. For example, check for loose or defective solder connections, integrated circuits loose in their sockets, loose cable connections, broken wires, and damaged PCBs or components.
Check Individual Components
Check soldered-in passive components (¢.g., resistors, capacitors, diodes) by disconnecting one end to isolate the measurement from the effects of the surrounding circuitry. Often, direct substitution is the most practical way to determine if a component is faulty. However, eliminate the possibility of some other circuit problem that could damage the substitute component.
Repair the Assembly
| CAUTION
Soldered-in transistors and integrated circuits are difficult to remove without damaging the printed-circuit board or component. Refer to the information in this chapter pertaining to soldering and replacing integrated circuits and | transistors.
Repair or replace the defective part. Refer to Chapter 4 and information in this chapter for special removal and replacement procedures. Check for proper operation of the repaired circuit.
Soldering Techniques
Observe the following recommendations when removing or replacing components soldered to a PCB. Poor so!dering practices can damage a PCB or heat-sensitive electrical components.
Choosing the proper soldering iron is essential before attempting to remove or replace soldered-in components. Excessive heat is a common cause of damage to a component or PCB. However, transient voltages from solder guns or improperly grounded soldering irons can also damage certain voltage-sensitive semiconductor devices. Refer to Troubleshooting Static-Sensitive Devices tor more specific information.
A15-to27-watt pencil-tip soldering iron is recommended to avoid separating the etched circuit wiring from the board material and to avoid damaging active components. A temperature-controlled soldering station rated at 700°F with a fine cone or a very fine chisel tip can also be used.
720°
The following additional equipment is recommended for | removing and replacing soldered-in components:
- Solder Sucker—Hand-operated vacuum tool used to remove liquified solder from the PCB. We recommend the top-of-the-line Soldapullt® brand. Solder Wick—Resin-soaked copper braid used for removing excess solder from the lead connections on the PCB. See Removing Integrated Circuits for precautions relating to the use of a solder wick on a multilayer PCB with plated-through holes. Flux Remover—Non-corrosive chemical used to clean foreign material from the PCB before soldering and to remove any flux residue where components have been replaced. Also used to clean any foreign material from the PCB during preventive maintenance. Isopropyl alcohol is recommended.
Acid Brush—Small stiff-bristled paint or toothbrush used with flux remover to clean flux and other foreign matesial from the PCB.
Removing Integrated Circuits
The easiest and safest method for removing soldered-in integrated circuits (IC) from a PCB is to cut off each pin as close to the IC case as possible with a tip dyke (diagonal cutter) as shown in Figure 5-1. Use the proper soldering iron as previously described under Soldering Techniques. Then, to avoid excessive heat buildup in one area of the PCB, apply heat directly to each pin in arandom order. Remove the loosened pin with the tip of the soldering iron or a needle-nose pliers as shown in Figure 5-2. Allow a moment for the PCB to cool before
Diagonal Cutter
Figure 5-1 Removing IC (Cut-Pin Method) Yroubleshooting
; Needle-Nose Pliers
Soldering tron
Figure 5-2 Removing IC Pins
proceeding to the next pin. Apply just enough heat to remove any stubborn pins. For a multi-layer PCB with plated-through holes, use a solder sucker to remove the remaining solder from inside each hole as shown in Figure 5-3. If possible, suck the solder from the opposite side of the PCB from where the heat is applied. Use a solder wick to remove excess solder from around the lead connection pads on the top and/or bottom surface of the PCB as shown in Figure 5-4
Use an integrated-circuit (IC) pulling tool to remove sockeied ICs. Do not pry up on one end of the ICs, because the pins could be bent or broken.
Troubleshooting Static-
Sensitive Devices
Certain precautions must be taken when working with static-sensitive devices, e.g., microprocessors, field-effect transistors (FET), complementary metal-oxide semiconductors (CMOS), and other large-scale integration (LSI) devices that use metal-oxide semiconductor (MOS) technology. Static charge buildup in a person’s body or leakage from an improperly grounded soldering iron can cause static-sensitive device failure.
Before handling a static-sensitive device or a PCB with such devices attached to it, ground any static voltage that may have accumulated in your body by touching an ob-
5-3
Troubleshooting
Soldering Iron
Solder Sucker
Preterred Method 720°
Soldering Iron
Alternate Method
Figure 5-3, Removing Solder from Plated-Through Holes
dering It Soldering !ron Solder Wick
Figure 5-4 Removing Solder from Lead Connection Pads
ject that has been earth grounded. A bare wire wrapped around your wrist and attached to an earth ground is ef-
5-4 fective when working extensively with static-sensitive devices. When soldering a static-sensitive device, use a soldering iron with a properly grounded three-wire cord. (Refer to Soldering Techniques for a discussion of recommended soldering irons and procedures.) A static-sensitive device can appear defective due to Jeakage on a PCB. Observe the precautions for grounding static voltages described in the preceding paragraph and clean both sides of the PCB with flux remover or an eraser before replacing what can be a good static-sensitive device. For discrete FETs, clean thoroughly between the gate, drain, and source leads.
Static-sensitive devices can be packaged in conductive foam or have a protective shorting wire attached to the pins. Remove the conductive foam just prior to inserting the device into its socket or soldering it toa PCB. Remove the shorting wire only after the device is inserted into its socket or after all the leads are soldered in place.
Chapter 6
Illustrated Parts Lists
This chapter provides information you need to order parts for your game. Common hardware (screws, nuts, washers, tc.) has been deleted from most of the parts lists. The PCB parts lists are arranged in alphabetical order by component. Each component subsection is arranged alphanumerically by reference designator. Other parts lists are arranged alphanumerically by Atari part number. In these parts lists, all A-prefix numbers come first. Following these are numbers in sequence evaluated up to the hyphen, namely 00- through 99-, then 000598- through approximately 201000-. When ordering parts, please give the part number, part name, number of this manual, and serial number of your game. This will help us fill your order rapidly and correctly. We hope the results will be less downtime and more profit from your game. Atari Customer Service numbers are listed on the inside front cover of this manual.
Wlustrated Parts Lists 720°
+ Part used only in US-bullt cabinets 4% Part used only in Irelanc-built cabinets
A043912-01 x, or A043912.51 Light & Speaker Grille Assy 043904-01 *, or 043904-51 % Retainer Decal Lamp and « Lamp Receptacle 043876-01 *, or 139019-001 \ See Figure 6-4 04387651 % Wells Gardner Display yO Glass Retainer :
Light and Speaker Panel Assy See Figure 6-4
043906-01 *, or 043906-51 & Display Bezel A005493-01 *, or A005493-02 Light Hamess Assy VY
043872-01 x, or 043872-51 & Display Shield
Rotary Control Assy 043899-01 &, oF See Figure 63 043899-51 Detail Cleat Control Panel Assy“ > See Figure 6-2 178013-001 Spring Draw Latch:
171078-002 x, or 400246403 Ronieowie A043893-01 x, or
A043893-51 Coin Door Assy « Cabinet Control Harness Assy See Figure 6-6, or 5 A037619-45TS Coin Door (German 1DM/DM)
Audio Il PCB Assy See Figure 6-10
: 78-3201 038031-01 Adjustable Glide Cain Box
Figure 6-1 Cabinet-Mounted Assemblies A043870-01 B(US) and A043870-51 _B (Ireland)
6-2
m2u8 Mlustrated Parts Lists
A043869-01 », or A043869-51 # Cabinet Assy
043858-01 *, or 043858-51 % Display Enclosure Rear Door Panel
CPU PCB Assy See Figure 68
A038881-01 k A 043877-01 *, or Lock Assy 043877-51 % Ground Plane Zz N ®& 178093-001 A043890-01 x, or Fan Guard A043890-51 % Main Harness Assy 002 05 *, OF 4 171002-103 % | Fan A043615-01 x, or A043615-51 Video Harness Assy A043617-01 *, or A043617-51 $ 034536-04 Fan Cord Assy Ye-Inch Vibration Camper 034536-10 Yelnch Vibration Damper aaa : 043859-01 x, or Video PCB Assy : 043859-51 & See Figure 6-9 (behind EMI cover) Rear Door Panel A043891-01 *, or A043891-51 # AC Harness Assy 043148-01 *, or 043148-51 & EMI Cover A040586-01 «, or A040586-04 % Power Cord Assy
040036-01 Power Supply Assy 4943910-01 x, 0r = Power Cord Piate See Figure 6-5 A043910-04 On/Off Switch Assy with Harness.
Figure 6-1 Cabinet-Mounted Assemblies, Continued A043870-01 B (US) and A043870-51 _B (Ireland)
Hlustrated Parts Lists 720°
Cabinet-Mounted Assemblies Parts List
PartNo. Description
A0N02464-03 A037619-45TS ® A005493-01 % A038881-01
A040586-01 A043615-01 * A043617-01 A043661-01
AU43829-01 A043869-01 A043888-01 A043890-01 OF
A043891-01 A043893-01 A043900-01 A043901-01 +e eH
A043910-01 A043912-01 A043921-01 A043922-01 +e
78-3201 78-6900402 034536-04 03453610
038091-01 040036-01 043148-01 043858-01 oF
043859-01 043872-01 043876-01 043877-01 tt OF
043899-01 043904-01 043906-01 139019-001 ot OF Oe
171002-001 * 171002-003 ® 171078-002 * 178013-001 178093-001
TM-294 SP-294 ST.294 TM-295 10 V Coin Counter Assembly Coin Door for German 1 DM/1 DM Light Harness Assembly (A005493-02 @) Lock Assembly for Rear Panel
Power Cord Assembly Video Harness Assembly (A043615-51 ) Fan Cord Assembly (A043617-51 #) Audio H PCB Assembly
Rotary Control Assembly Cabinet Assembly (A043869-5] @) Power Supply Assembly (A043888-51 ) Main Harness Assembly (A043890-51 ®)
AC Harness Assembly (A043891-51 $) Cabinet Controi Harness Assembly (A043893-51 #) Control Panel Assembly (A043900-51 #) Light and Speaker Assembly (A043901-51 @) On/Off Switch Assembly with Harness (A043910-04 ®) Light and Speaker Grille Assembly (A043912-5i #) CPU PCB Assembly Video PCB Assembly
Adjustable Glide 4-Inchx %Inch Foam Tape (42 inches required; used on inside lip of retainer) Ys-Inch Thick Vibration Damper Inch Thick Vibration Damper
Coin Box Power Cord Plate EMI Cover (04314851 ®) Display Enclosure Rear Door Panel (043858-51 #)
Rear Door Panel (043859:51 #) Display Shield (043872-51 #) Glass Retainer (043876-5 1 #) Ground Plane (04387751 #)
Detail Cleat with Holes and Paint; .75 inches square x 16 inches long (043899-51 %) Retainer Decal (043904-51 #) Display Bezel (043906-51 #) Wells-Gardner 25-Inch Medium-Resolution Framed Color Raster Display, Model 25K5515
Exhaust Fan, 110 V (70 CFM) Exhaust Fan, 220 V (110 CEM) Terminated Non-Resettable Coin Counter, 12 VDC spring Draw Latch Fan Guard
The following are technical information supplements for this game: 720° Operators Manual 720° Schematic Package 720° Self-Test Label Wells-Gardner 25-Inch Medium-Resolution Color Raster Display Manuai
& Part used only in Us-built cabinets @ Part used only in (reland-built cabinets
720° Mlustrated Parts Lists
- Part used only in US-built cabinets 178030-008 @ Part used only in Ireland-built cabinets: Button Assy 75-9910NO Stamped Nut 160013-001 043875-01 *, or Leaf Switch with Button Holder 043875-51 & Control Panel
Rotary Control Assy. See Figure 6-3
A043894-01 +, or ‘A043894-51 Harness Assy
043903-01 «, or 043903-51 Control Panel Decal
75-9418 Hex Nut 75-5112B ‘Carriage Bolt
Figure 6-2 Control Panel Assembly A043900-01 8B (US) and A043900-51 _B (Ireland)
Control Panel Assembly Parts List
Part No. Description
A043820-01 Rotary Control Assembly A043894-01 Conirol Harness Assembly (A043894-51 ) 75-5112B #10-24 x '4-Inch Black Carriage Bolt 75-9418 Polymer Self-Locking Hex Nut
75-9910NO #1 yelnch Stamped Nut 043875-01 & Control Panel (043875-51 ®) 043903-01 Contsol Panel Decal (043903-51 #) 160013-001 Leaf Switch with Button Holder 178030-008 Blue Button Assembly
- Part used only tn US-built cabinets ® Part used only in Ireland-built cabinets
720°
043821-01 {Lithium Grease Pivot hey a tight oi —— ‘ 72-1408F = #4-40x Yen, Pan-Head Screw ys Hlustrated Parts Lists
72-8007 / 043803-01 v2 . Botorn Housing Plate. #10-32 x Zein. Cap anya a J
043808-01 Leesa PCB Bracket 043920-01 Encoder Disc Shield Dual Opt. Cplr. PCB Assy
75-040S #10 Lock Washer
2 175009-467 7 Nylon Washer
| /p | J | 043810-01 |
| ; | , | Bearing Housing |
(1-piece assy.) # WA ? 75-048S
| / | vA | #8 Lock Washer |
> f 72-8808 Pieced ™ #8-32 x Ye-In. Cap Screw “ lylon Washer, 175001-001 , ‘Curve Wave Washer Lubri “ /
| 4 Chain | Lubricant | / | 043817-01 |
‘Sprocket Post 178012-004 Retaining Ring ———?-—S ith a {Lithium Grease 043818-01 178200-001 Modified Sprocket Chain
175009-217 Nylon Washer 73-20812 Yen. Dia, x Yin. Spring Pin
178199-001 Sprocket 041787-02 Etched Encoder.
178001-003 043609-01 Retaining Ring Encoder Disc Mounting Plate
043813-01
043807-01 Centering Disc
75-014S #4 Flat Washer 4 gw a oats ae Lock Washer 7214128 So 44.40 x ¥e-In Pan-Head Screw Figure 6-3 Rotary Control Assembly A043820-01 C
720°
/ 039721-01 Lower Housing
043822-01 Bottom Housing
Y£ / a Ulustraicd Pars Lists:
043806-01 Handle >
043804-01 Disc {
A Lithium Grease
™
043811-01 73-3006 Poller Retaining Ring 039722-01 Va Upper x (oS
4 Lithium Grease
039716-01 Pivot Ball 4 >) Ot <?- 4-01 043812-01 ‘Bushing Lower Ball /
*
- 73-200814 , Yin. Dia. xn, Spring Pin
—s 178001-001 ‘S<—_—___. Retaining Ring
A Lithium Grease
75-028S. /
> #8 Narrow Flat Washer
72JA4824B #816 x 194-In, Pan-Head Screw
Figure 6-3 Rotary Control Assembly, Continued A043820-01 C
Illustrated Parts Lists
Rotary Control Assembly Parts List 720°
Part No. Description
A043882-01 1408F 7214128 72-6606S
75-0288 75-0408 75-0448, 75-0488
039716-01 039721-01 039722-01 041787-02
043803-01 043804-01 04380601 043807-01
043808-01 043809-01 043810-01 043811-01
04381201 043813-01 043814-01 043817-01
043818-01 043821-01 043822-01 043920-01
107013-001 107027-001 107028-001 175001-001
175009-217 175009-467 178001-001 17800 1-003
178012-004 178199-001 478200-001 72JA4824B Dual Optical Coupler PCB Assembly #4-40 7 2-Inch Pan-Head Screw #4-40 7 %-Inch Pan-Head Screw #632 7 #-lnch Sclf-Tapping Pan-Head Screw
#10-32 4 %-Inch Socket Head Cap Screw #4-407 cinch Socket Head Cap Screw #832 7 (elnch Socket Head Cap Screw #832 / Ye-Inch Socket Head Cap Screw
Inch Diameter x %-Inch Spring Pin Beinch Diameter x %-inch Spring Pin Retaining Ring #4 Flat Washer
#8 Narrow Flat Washer #10 Lock Washer #4 Lock Washer #8 Lock Washer
Pivot Ball Lower Housing Upper Housing, Etched Encoder
Bottom Housing Plate Disc Handle Centering Disc
PCB Bracket Encoder Disc Mounting Plate Bearing Housing Roller
Lower Ball Centering Disc Spacer Bushing Sprocket Post
Modified Sprocket Pivot Arm. Bottom Housing Encoder Disc Shield
Light Oil Lubricant Lithium Grease Lubricant Chain Lubricant Curve Wave Washer
Nylon Washer 032 Thick x 375 LD. x .087 O.D. Nylon Washer Retaining Ring Retaining Ring
Retaining Ring OT Sprocket 25 42-Pitch Endless Chain #8-16 x 15-inch Plastite Pan-Head Screw
720° Ilustrated Parts Lists
- Part used only in US-butt cabinets @ Part used only in |reland-built cabinets. A005493-01 *, or ‘A005493-51 § 4 Light Hamess Assy 170001-001 *, or 170001-101 incandescent Lamp zg 179239-001 Lamp Receptacle
043864-01 x, or 043864-51 § Light & Speaker Panel
A043912-07 *, or ariel ‘A043912-51 % \P Light & Speaker Gell Assy Speaker Harness Assy
148008-002, or 17603-1608 148009-001 Screw Speaker
Figure 6-4 Light and Speaker Panel Assembly A043901-01 A (US) and A043901-51 A (Ireland)
Light and Speaker Panel Assembly Parts List
Part No. Description
A005493-Ol Light Harness Assembly (A005493-5 1 #) A043892-01 * Speaker Harness Assembly (A043892-51 @) A043912-01 Light and Speaker Grille Assembly (A043912-51 ) 043864-01 & Light and Speaker Panel (043864-5 1 ®)
148008-002 8-Inch, 88, 20 W Speaker (Pioneer AZ0EP80-03FW) OR 148009-001 8-Inch, 16Q Speaker (Onk) 170001-001 *& Clear 25 W Medium-Base Tubular Incandescent Lamp (170001-101 @) 176033-1608 #6 x ¥2-Inch Cross-Recessed Pan-Head Deep-Thread Screw 179239-001 Medium-Base Lamp Receptacle
Part used only in US-built cabinets fart used only in Ireland-built cabinets
filustrated Parts Lists
x Part used only in US-uilt cabinets 4 Par. used only in Ireland-built cabinets A043367-06 *, or A043367-56 $ A043367-07 *, or Jumper As A043367-57 $ A043909-01 «, or Jumper Assy A043%09-51 8V Harn\ss Assy
'043886-01 %, or 043886-51 Power Supply Chassis Bas
037640-01 &
72-HA4608S, Screw.
034544-01 Fuse Block Cover
Fuse Label (F2, F3. Fa) 179225-2203 Fuse Block 142044-001 *, or 142044-101 & Transtormer 72-HA4806S Screw 720°
149006-001 *, or 149006-101 & Hition $V Switching Power Supply Sub-Assy 179231-002 Terminal Block A043367-01 *, or A043367-51 Jumper Assy
179225-2201 Fuse Block
043908-01 *, or 043908-51 # Fuse Label (Ft) A042384-01 Line Filter Assy
Figure 6-5 Switching/Linear (SL) Power Supply Assembly A043888-01
6-10 A (US) and A043888-51 A (Ireland)
m2
Switching/Linear (SL) Power Supply Assembly Parts List Ulustrated Parts Lists
Part No. Description
42384-01
404330706 AQ43307-07
A043909-01 46-201 2002 46-2013002 72-HA4608S
HA4806S, 03 C1 037640-01 043886-01
043908-01 043908-02 & 142044-001 149006-001 *
179225-2201 179225-2203, 17923 1-002 Line Fier Assembly Jumper Assembly (A043 367-51 @) 9-Inch, Black Jumper Assembly (A043367-56 #) 9-Inch, White Jumper Assembly (A043367-57 #)
5 V Harness Assembly (A043909-5 1 #) 250 V Slow-Blow 2 A Fuse 250 V Slow-Blow 3 A Fuse #6-32 x ¥-Inch Cross-Recessed Pan-Head Thread-Forming Screw
#8-32 x %-Inch Cross-Recessed Pan-Head Thread-Forming Screw Fuse Block Cover Power Supply Warning Label Power Supply Chassis Base (043886-51 #)
Power Supply Fuse Label; Fuse F1 (043908-51 ) Power Supply Fuse Label; Fuse F2, F3, F4 (043908-52 #) Transformer (142044-101 #) Hitron 5 V 13 A Switching Power Supply Sub-Assembly (149006-101 #); see below
1-Position Fuse Block 3-Position Fuse Block 2-Position Terminal Block
- Part used only in US-built cabinets % Part used only in Ireland-built cabinets
Hitron 5-Volt Power Supply Sub-Assembly Parts List
| Designator | Description | Part No. |
Capacitors
| cl | Capacitor, Metal Film, 0.047 uF, 250 V | 99-211036 |
| C2 | Capacitor, Metal Film, 0.1 pF, 400 V | 99-211038 |
| C3, C4 | Capacitor, Ceramic, 4700 uF, 400 V | 99-211049 |
| 5, C6 | Capacitor, Electrolytic, 100 nF, 200 V | 99-211046 |
| C7 | Capacitor, Metal Film, 0.1 pF, 400 V | 99-211038 |
| c8 | Capacitor, Ceramic, 0.001 wF, 2 kV | 99-211042 |
| co | Capacitor, Ceramic, 0.01 wF, 1 kV, Z5U | 99-211041 |
| C10 | Capacitor, Electrolytic, 220 wR, 25 V | 99-211045 |
| cll | Capacitor, Metal Film, 0.22 4F, 100 V | 99-211037 |
| C12 | Capacitor, Metal Film, 0.022 pF, 100 V | 99-211039 |
| C13 | Capacitor, Metal Film, 9.22 yF, 100 V | 99-211037 |
| cl4 | Capacitor, Ceramic, 1800 PF, 2 kV, Z5V | 99-211040 |
| C15-C18 | Capacitor, Electrolytic, 2200 pE, 16 V | 99-211069 |
| cig | Capacitor, Ceramic, 470 PF, 1 kV, Z5P | 99-211043 |
| C20 | Capacitor, Electrolytic, 2200 gk, 16 V | 99-211069 |
| C21 | Capacitor, Ceramic, 220 uF, 25 V. | 99-211070 |
Diodes
| D1, D2 | Diode, Fast Recovery, RPG1UK | 99-211064 | |
| b3 | Diode, | Fast Recovery, RPG15B | 99-211011 |
| D4 | Diode, | Fast Recovery, RPG 10B | 99-211009 |
| DS-D7 | Diode, | Switching, 1N4148 | 99-211012 |
Ol]
Illustrated Parts Lists 720°
Hitron 5-Volt Power Supply Sub-Assembly Parts List, Continued
| Designator | Description | Part No. |
| D8, D9 | Diode, Schottky, $15SC4M. | 99-211064 |
| D11, D12 | Diode, Schouky, S10SC4M | 99-211005 |
Diode, Rectifier, 1N4006 99-211008
Inductors
| LI | Inductor, 15 mH | 99-211052 |
| L2 | Inductor, 9.8 pH | 99-211071 |
| L6, L7 | Inductor, 7 pH (Acceptable substitute is part no. 99-211051) | 99-211050, |
| L4 | Inductor, 2.2 pH | 99-211054 |
| us | Inductor, 1.5 mH | 99-211053 |
Resistors
| RI, R2 | Resistor, Carbon Film, 180 kQ, +5%, 1W | 99-211034 |
| R3 | Resistor, Wirewound, 1209, +5%,2 W | 99-211019 |
| R4 | Resistor, Wirewound, 0.47 2, +5%,2 W | 99-211018 |
| R5 | Resistor, Wirewound, 279, +5%,2W | 99-211065 |
| RG, R7 | Resistor, Carbon Film, 5.69, +5%, 4 W | 99-211027 |
| R8 | Resistor, Wirewound, 0.479, +5%, 2 W | 99-211018 |
| RO | Resistor, Carbon Film, 102, +5%, 4’ W | 99-211029 |
| R10 | Resistor, Carbon Film, 1kQ, +5%, 4 W | 99-211032 |
| RI | Resistor, Carbon Film, 472, +5%, 4 W | 99-211025 |
| R12 | Resistor, Carbon Film, 5.6 Q, +5%, 4 W | 99-211027 |
| R13 | Resistor, Carbon Film, 3302, +5%, 4 W | 99-211026 |
| R14 | Resistor, Carbon Film, 270, +5%, % W | 99-211023 |
| RIS | Resistor, Carbon Film, 3300, +5%, '% W | 99-211022 |
| RIO | Resistor, Carbon Film, 8.22, +5%, *« W | 99-211028 |
| R17, RIB | Resistor, Carbon Film, 562, +5%, 4 W | 99-211031 |
| R19 | Resistor, Carbon Fiim, 398, +5%, 4 W | 99-211030 |
| R20 | Resistor, Carbon Film, 2 k®, +5%, 4 W | 99-211035, |
| R23 | Resistor, Carbon Film, 470 @, +5%, 4 W | 99-211024 |
| R22 | Resistor, 2.2 k®, +2%, 4 W | 99-211021 |
| R23 | Resistor, Metal Film, 2k, +2%, 4 W | 99-211033 |
| R25 | Resistor, Carbon Film, 102, +5%, 4 W | 99-211029 |
| R26 | Resistor, Carbon Film, 6.82, +5%, 2 W | 99-211066 |
| R27 | Resistor, Carbon Fiim, 12 8, +5%, 4 W | 99-211067 |
| R28 | Resistor, Carbon Film, 2.42, +5%, % W | 99-211068 |
| R31 | Resistor, Wirewound, 1502, +5%,2W | 99-211016 |
Transistors
| Ql | Transistor, NPN, 2SD725 | 99-211062 |
| 2 | Transistor, NPN, PE8050B | 99-211003 |
| 3 | Transistor, PNP, PE8550B | 99-211063, |
Miscellaneous
| Fl | Fuse, 2 A, 125 V, Semko | 99-211058 |
| Cl | Regulator, UA431 AWC | 99-211001 |
| SCRI | Thyristor, SCR | 99-211013 |
| Tl | Transformer | 99-211055, |
| T2 | ‘Transformer | 99-211055 |
| TRI | Thermistor, 0.59, +5%,5 W | 99-2110920 |
| VRL | Potentiometer, Trimming, 3 kQ | 99-211014 |
| ZDL | Diode, Zener, 1N752A4 | 99-21 1007 |
Fuse, 2 A, 250 V 99-211056 Fuse Holder 99-211060 Termiral Block, 8 Ckt. 99-21 1057 Heat Sink 99-211059 Heat Sink, 1.5 mm 99-211061
G12
F208 Mlustrated Parts Lists
N O T E S
O13
Tihustrated Parts Lists 720°
99-10140 Panel Asser’n
75-948S Locknut
99-10116
99-10152 Right Coin Inlet 99-10147 Harness 171006-035 Coin Mechanism
75-9448 Locknut
99-10096 Fastener
99-10151 Left Coin Inlet
99-1080 Larnp Socket
J y , 99-10105 72-9406 ; | K “a ] Bar Screw SG
¥
99-10104 Bar Retainer
a 99-10042 thru 99-1045 99-10154 a Coin Switch Assembly Bracket Assembly
99-10153 Coin Return Box S 99-10150 / : Switch Cover 99-10068 xo yr > Coin Chute : woe 65-4416 N < L Coin Switch * A a 7 99-10075 thru 99-10078 RN ‘Switch Wires SS 99-10008 Retainer 7614125
Screw
Figure 6-6 Coin Acceptors, Inc. Coin Door Assembly 171027-001 A
O14
720° Mustratca Parts Lists
99-10148 Lock Assembly
99-10142 Burton Houstrie:
72-HA1404C Screw
99-10134 99-10139 99-10119 Cove ~ |~———— Button Assemibh Coin Docr — v sgonse Hor
99-10115 99-10148 Spa Lock Assembly
a 99-10141 a Coin Reurn Cover g cn 8 99-10117 Com Res Door
72-JA1405B - Screw
~~ 99-15066
Screw
99-10149 Setuice Door
038091-01 Coin Box
99-10143, Frame
Acceptable alternate or substi tute coin door assembly 1s part number 171034004 | ;
Figure 6-6 Coin Acceptors, Inc. Coin Door Assembly, Continued 171027-001 A
ol a
iMtustrated Parts Lists 720°
Coin Acceptors, Inc. Coin Door Assembly Parts List
Part No. Description
65-441C Coin Switch FON-47 Miniature Bayonet Lamp 72-9406S #4-40 x 3/8-Inch Truss-Head Screw 72-HA1404C #4-40 x 1/4-Inch Pan-Head Screw
72-JAL405B #4-40 x 31-Inch Pan-Head Screw 75-1412S, #4-40 x 3/4-Inch Pan-Head Screw 75-9945, #4-4) Locknut 99-10008 Retainer
99-0042 Coin Switch Assembly for Belgium 5 Fr and U.S. $.25 99-10043 Coin Switch Assembly for German | DM, Japanese 100 Yen, Swiss 1 Fr 99-10044 Coin Switch Assembly for German 2 DM, Italian 100 L, U.S. $1.00 99-10045, Coin Switch Assembly for Australian $.20, German 5 DM, British 10 P
99-10068 Coin Return Chute
| 99-10075, | Switch Wire | (included in coin switch assembly 99-10043) |
| 99-10076 | Switch Wire | (included in coin switch assembly 99-10042) |
| 99-10077 | Switch Wire | (included in coin switch assembly 99-10044) |
| 99-10078 | Switch Wire | (included in coin switch assembly 99-10045) |
99-10080 Lamp Socket 99-10081 Key Holder 99-10096 Fastener
99-10104 Bar Retainer 99-10105 Bar 99-10115 Spring 99-10116 Plastic Coin Return Lever
99-10117 Steel Coin Return Door 99-10118 Amber Coin Return Button 99-10119 Amber Coin Button for U.S. $.25 99-10134 Coin Button Cover
99-10139 Coin Door 99-10140 Coin Door inner-Panel Assembly 99-10141 Die-Cast Coin Return Cover 99-10142 Die-Cast Button Housing
99-10143 Coin Door Krame 99-10144 Channel Clip 99-10147 Harness. 99-10148 Lock Assembly
99-10149, Service Door 99-10150, Switch Cover 99-10151 Left Coin Inlet D9AOIS2 Right Coin Inlet
99-10153, Goin Return Box 9910154 99-1506, Screw for Chimp 171006-035 Metal Coin Mechanism for U.S. $.25
720° Mlustrated Parts Lists,
CPU PCB Assy é 043877-01 See Fiougs® Ground Piane
178181-6802 034536-04 Spacer Ye-Inch Foam Damper
Video PCB Assy See Figure 69
176031-2616 Thumb Screw
t 176015-112 Screw
177018-206 Thumb Nut
034536-10 Yelnch Foam Damper
043148-01 EMI Cover NOTE
‘To comply with emission requirements, the Federal Communications Commission requires that the Video PCB Assembly be housedin the EMI cover. Do not operate this game without properly installing the EMI cover, metal spacers, and thumb nuts.
Figure 6-7 PCB Mounting Hardware
PCB Mounting Hardware Parts List
Part No. Description
A043921-03 CPU PCB Assembly A043922-01 Video PCB Assembly 034536-04 ¥2-Inch Foam Vibration Damper 034536-10 {Inch Foam Vibration Damper 04314801 EMI Cover 043877.01 Ground Plane 176015-112 10x %-Inch Cross-Recessed Pan-Head Deep-Thread Screw 17601-2616 #6-32 x Ye-Inch Knurled Thumb Screw
177018206 #6-32 Knurled Thumb Nut 178181.6802 Round Spacer
6-17
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
Tur
720° Central Processing Unit (CPU) PCB Assembly Mlustrated Parts Lists
Parts List
Desig- Desig:
| nator | Description | PartNo. | nator | Description |
| Integrated Circuits | sp | Integrated Circuit, Type 7418245 | ||
| ted Circuit, Type-611e | TAT21 1-004 | SE | Integrated Circuit, | Type-7aL S374 |
| it, Type-OL10 | 7211-001 | oe | ||
| Circuit. | Type-2804-4 | 137329300 | “F |
EEPROM Su
| IE | Integrated Circuit, Tepe-7AL832 | A 4LSa2 | 5) | Jategrated Circuit, T |
5K Integrated Circuit, Type-741804 1 Integrated Circuit, Ik Integrated Circuit, Type-74
| IL | rat | pe-74L$32 | integrated Circuit, Type-74L9373 | |||
| IM | Integrated Citcuir, T | 4 | Integrated Circuit, Type-74L5174 | |||
| Integrated | Cir | 74182 | 7 | |||
| IN | Integeated Circuit, Type-74L S244 | megeared Treut, Tyne | 7408 | 3 | ||
| Pp | Incegraced Circuit, Type-74LS244 | 6B | Integrated Circuit, POKEY | €012294-01 | ||
| IR | Integrated Circuit, Type-74S32 | a | 6D | Integrated Circuit, Type-741S24 | 37-T4LS245 | |
| 1S | Integrated Circuit, Type-ADC0809 | 137243.001 | OE | Integrated Circuit, Type-74L9374 | 37-74LS374 | |
| 2a | Integrated Circuit, EPROM, | 1360475134 | orm | Integrated Circuit, EPROM, | 1500474128 | |
| Type27512, 200 ns | Type-27512, | 200 ns | ||||
| 18 | ieee a | alae | 16047135, | ong | Integrated Circuit, EPROM, | 136047-x129 |
| 2CD | integrated Circuit EPROM | Type27512, 200 ns | ||||
| . | Tepe2"512.200 8 | 6K | Integrated Circuit, EPROM, | 136047-x130 | ||
| - | ilies | sraneriige | 5 | Type-27512, 200 ns | ||
| 2F | Integrated Circuit, Type-74L524 | , | y | |||
| i | ee | * | MN | Integrated Circuit, EPROM, | 136047-x131 | |
| y | Integrated Circur, | Type27512, 200 ns | ||||
| Fype-TL1 (DCTIL-XA) | OP | Integrated Circuit, EPROM, | 136047-x132 | |||
| 2L | Integrated Circuit. Type-74L8174 | Type-275 12, 200 ns |
2M Integrated Circuit, Type-741574 ;
| 2N | Integrated Circuit, Type-74LS670 | OR | Integrated Circuit, EPROM, | 136047-x«133 |
Type-27512, 200 ns
| 2P | Integrated Circuit, Type-7418670 | 7B | Integrated Circuit, POKEY | €012294-01 |
| 3E | Imegrated Circuit, Type-7415138 | 7 | Integrated Circuit, Type-TM$5220C | 137308-002 |
| 3F | Integrated Circuit, Type-74LS161 | TF | Integrated Circuit, Leta | 137304-1001 |
3H Integrated Circuit, Type-74LS00
| . | 7 | 7H | Integrated Circuit, Type-741574 | 37-74LS74 | ||
| BI} | Integrated Circuit, Type-74L8139 | 7 | Integrated Circuit, Type-74LS10 | 37-74L510 | ||
| 3K | Integrated Circuit, Type-74L9393 | 7418393 | aK | cuit, | Ty | 7 |
| a | oie | 7K | Integrated Circuit, Type-116 | 137211-001 | ||
| 3 | Integrated Circuit, Type-74574 | Slits | TUM | Integrated Circuit, EPROM | 136047-x126 | |
| 3M | Integrated Circuit, Type-7415138 | 137 | 177-061 | Type27128, 300 ps | ||
| 3N | Integrated Circuit, Type-74LS74 | : | 5 | 0 | ||
| 3p | Integrated Circuit, Type? | MIN | Integrated Circuit, EPROM, | 136047-x127 | ||
| BR | integrated Circuit, Type-741820 | . | Type-27128, 300 ns | |||
| 4A | Integrated Circuit. Type 7419244 | ig | Integrated Circuit, Type-6116 | 137211-001 | ||
| 7R | Integrated Circuit, Type-74L5161 | 37-74LS16) | ||||
| 4alB | Integrated Circuit, Type-74L8244 | 8B | Integrated Circuit, Type-74LS161 | 37-74LS161 | ||
| 4BIC | Integrated | Circuit, Type-7415139 | ||||
| 4C1D | Integrated Circuit, Type-74LS74 | ac | integrated Circuit, Typ | |||
| sD | Integrated Circuit, Type-74L8193A | 8D | Invegrated Circuit, Type-7418275 | |||
| ; | _ | 8F | Integrated Circuit, Type-7415244 | 3 | ||
| 4E | Integrated Circuit, Type-74L5138 | 8Hh | Integrated Circuit, Type-Y2151 | 137401-001 |
4F Integrated Circuit, Type-741S393
| 4H | Integrated Circuit, Type-74L874 | IK | Integrated Circuit, Type-YM3012 | 137402-001 |
| 4 | Integrated Circuit, Type-74L874 | 8N | Integrated Citcuit, Type-74804 |
9B Integrated Circuit, Type-LF1 3201 4K Integrated Circuit, Type-7. ae hae
| ii | Imeprated Circuit, Type-74L8138 | 9c | Integrated Circuit, | Type-LF13201 | 137352-001 |
| 4M | Integrated Circuit, SLAPSTIC | B si. lu | °D | Integrated Circuit, Type-LF 13201 | 137352.001 |
| 4N | Integrated Circuit, Type 74L5245, | 37-74 | ODE | Integrated Circuit, Tepe | LEI3207 |
| 4p | Integrated Circuit, | Type-74.8244 | 37-741 8244 | on | |
| 5B | Integrated Circuit, Type-6502A, | 90-0013 |
Xx” in the part number denotes the revision level
Ilustrated Parts Lists: 720°
720° Central Processing Unit (CPU) PCB Assembly Parts List, Continued Desig- Desig:
| nator | Description | Part No. | nator | Description | PartNo. |
| 10B | Integrated Circuit, Type-LM324 | 37-LM324 | C122 | Capacitor, Ceramic, 22 pF, 25 V | 122004224 |
| 10C | Incegrated Circuit, Type-LM324 | 37-LM. | C123, | Capacitor, Ceramic, 22 pF 25 V | 1220004-224 |
| 10F | Integrated Circuit, Type-LM324 | 37-LM324 | . | , | |
| 1OLIM | Integrated Circuit, Type-TLOB2CP | 37-TLOB2CP | Capacitor, Mica, 470 pk, 100 V | 128002-471 | |
| uM | Integrated Circuit, Type-74C04 | 137309-001 | Capacitor, Mica, 470 pF, 100 V | 128002-471 |
Capacitor, Ceramic, 22 pF, 25 V 122004-224
| Sockets | Capacitor, Ceramic, 22 uF, 25V | 122004.224 | |||
| 16-Pin Medivin-Insertion-Force Socket | 79-42C 16, | _ | ips | 30 | 2 |
| 20 Pin Medium-Insertion-Foree Socket | 99-4200 | Capacitor, Ceramie, 1 a | 30 ¥ | 122002-t04 | |
| 24-Pin Medium-Insertion Force Socket | eapacnor, Ceratnic, .} #830 8 | 122002 104 | |||
| 28-Pin Mediurm-insertion-Force Socket | Capacitor, Ceramic, o sh, 308 | eee | |||
| 40-8in Mediurn-Insertion Force Socket | Capacitor, Ceramic, 22 pF, 25 V | 122004-224 | |||
| . | C135 | Capacitor, Aluminum, 470 pF, 25 V | 24-250477 | ||
| __ | Capacitors | C136 | Capacitor, Aluminum, 470 pF, 25 V | 24-250477 | |
| C1-C60_ | Capacitor, Ceramic, .1 wf, 50 V | 122002-104 | C138 | Capacitor, Ceramic, .1 pF, 50 V | 122002-104 |
| C31-C60 | Capacitor, Ceramic, .1 bE 50 V | 122002-104 | cB° | Capacitor, Aluminum, 100 pF, 35 V | 24350107 |
| C61 | Capacitor, Ceramic, 018 pF, 50 V | 122015-183 | |||
| 062-C64 | Capacitor, Ceramic, .22 uF, 25 V | 122004-224 | 140 | Capacitor, Aluminum, 1 pf, 50 V | 24-500105 |
| cil | Capacitor, Ceramic, .1 pF, 50 V | 122002-104 | |||
| C65 | Capacitor, Ceramic, .1 wf, 50 V | 122002-104 | C143 | Capacitor, Ceramic, .1 uF, 50 V | 122002-104 |
| C66 | Capacitor, Ceramic, .1 pF 50V | 122002-104 | C144 | Capacitor, Ceramic, .0027 uF, 50V | 122015-272 |
| 67 | Capacitor, Mica, 100 pF, 100 V | 128002-101 | . | ||
| C68. | Capacitor, Mica, 39 pF, 100 V | 128002-390 | C145 | Capacitor, Ceramic, .0012 pF, 50 V |
C146 Capacitor, Ceramic, .0039 pF, 50V
| C69 | Capacitor, Ceramic, .1 uF, 50 V | 122002-104 | C47 | Capacitor, Ceramic, .0068 wF, 50 V | 122015-682 |
| c70 | Capacitor, Mica, 39 pF, 100 V | 128002-390 | cl4g | Capacitor, Ceramic, .1 pk 50 V | 122002-104 |
| cv | Capacitor, Mica, 100 pF, 100 V | 128002-10i | C149-C152. Capacitor, Ceramic, .1 xf. 50V | 122002-104 | |
| C72-C79 | Capacitor, Ceramic, .01 uF 23 V | 122005-103, | |||
| 80 | ce | 122002-102 | ee | ||
| Capacitor, Ceramic, .001 pF, 50.V | 22002102 | CRI-CR3— | Diode, Type-1N100 | 31-1N100 | |
| C81 | Capacitor, Ceramic, .001 pF, 50 V | 122002-102 | ‘ | SING | |
| SOY | F | cR4 | Diode, Type-iN4001 | 31-IN4001 | |
| C82-C89 | Capacitor, Ceramic, .1 #F, 50 Y | 122002-104 | CRS | Diode, Type-1N4001 | 31-IN4O01 |
| 90 | Capacitor, Ceramic, .22, 25 V | 122004-224 | CRE | Diode, Light Emitting, Tepe-aiv5058 | he |
7 IN
| coi | Capacitor, Tantalum, 10 pf, 20 V | 29.046 | CR | Diade, Typel | M00} | |||
| 92 | Capacitor, Ceramic, .01 pF, 25. V | 122005-103 | Conneetors and Fasteders | |||||
| C93 | Capacitor, Mica, 220 pF, 100 V | 128002-221 | 4% | Connector, Header 17-Circuit, 100 cur | 179118-0)7 | |||
| C94 | Capacitor, Mica, 220 pF, 100 V | 128002-221 | J | pao | Me | in | 4 | u |
| * | ” | . | “ | Ji6 | Connector, Header, 5-Circuit, 100 ctr | 17918-0035 | ||
| co | Capacitor, Ceramic, 0027 nF, 50 V | 122015-272 | 320 | Connecter, Header, 9-Circuit, .156 cu, | 179014-009 | |||
| C96 | Capacitor, Tantalum, 10 pF, 20 V | 29-046 | . | pol | . | og | ||
| co | Capacitor, Ceramic, 0027 pF, 50 V | 122015-272 | J103 | Connector, Header, 11-Circuit, 100 ctr | 179118-011 | |||
| CHC Ot | Sapacitoe Cenatnle, 1 pk 50Y | $22002-104 | J106 | Connector, Header, H1-Circuit, 100ctr | 179418011 | |||
| C101 | Capacitor, Aluminum, 19 pF, 35 V | 24-350106 | P18 | Connector, Card Edge, 80-Circuit | 179221-180 | |||
| C102 | Capacitor, Aluminum, 10 pF 35.V | 24-350106 | (40x2) | " | ||||
| €103-C109 Capacitor, Ceramic, .1 pF, 50 V | 122002-104 | Q1,.Q2 | Fastener, Nylon, Snap-in | 81-4302 | ||||
| Clo | Capacitor, Ceramic, .01 wk, 25V | 122005-103 | Q9,Q10 | Fastener, Nylon, Snap-in | 81-4302 | |||
| cil | Capacitor, Ceramic, .01 pF 25 | 122005-103 | WEI | Fastener, Nylon, Snap-In | poe | |||
| ch2 | Capacitor, | Ceramic, .1 pF, 50 V | 122002-104 | ‘Terminal, Fast-On Tab (Acceptable sub- — 179051-002 | ||||
| cB | Capacitor, Ceramic, .1 aE 50 V | 122002-104 | stitute is part number 02067001) | |||||
| Cis | Capacitor, Mica, 220 pF, 100 V | 128002-221 |
Inductors
| C116 | Capacitor, Mica. 220 pF, 100 V | 128002-221 | LI | Inductor, 33 pil | 1-41016-007 |
| CHy | Capacitor, Ceramic. 01 pF, 25 V. | 122005-103, | i | Inductor, 100 pH | 14 1002-001 |
| Cil8 | Capacitor, Ceramic, 001 pf, 50 V | 122002-102 | |||
| cil9 | Capacitor, Ceramic, .001 2F, 50 V | 122002-102 | Transistors | ||
| QL. Q2 | Transistor, 2NGO44 | 34-2NG044 | |||
| C120 | Capacitors, Ceramic, .01 mF, 25 V | 122005-103 | Qu | 6 | |
| C121 | Capacitor, Ceramic, .1 pF 50 V | 122002-104 | 5-08 |
QU QL wsistor, 2N3904
6-20 x" dn the part number denotes the revision level
720° Hlustrated Parts Lists
720° Central Processing Unit (CPU) PCB Assembly Parts List, Continued Desig- Desig-
| nator | Description | Part No. | nator | Description | Part No. | |
| Resistors | RUB | Resistor, & W,5 OK Q, 45% | 110000562 | |||
| RI, RE | Resistor, 4 WL10KQ, +5% | 10000-1003 | Ril4 | Resistor, 4 W, LOK Q, 45% | 110000-103 | |
| R3, Ra | Resistor, 4 W | + | 110000-102 | R115, RIG Resistor, 6 Wy IK 2, +5% | 110000-102 | |
| R5-R7 | Resistor, | 209, +5% | 110000-221 | RUT | 4 W470 0. $ 5% | 110000-471 |
| R8-RIT | Resistor, | PKA, | £5% | 11.0000-472, | ||
| RU8 | I W, A709, 45% | HLOWQO-ATT | ||||
| RID | Resistor, | 700, £5% | 110000471 | RIO | th W, 470K 2, + 5% | 110000474 |
| R13-R20 | Resistor, | 110000-101 | RI20-R124 | tn W, 100K Q, 45% | 110000-104 | |
| R21-R23__ | Resistor, | t | 110000-102 | R125 | Resistor, 4 W, 2.2KQ, + 5% | 110000-222 |
| RAT | Resistor, | WMV LTED, 9% | 110000-¢ | R126, R127 Resistor, % W, 4.7K Q, + 5% | 140000-472 | |
| R28-R33— | Resistor, 4 W, 4700, +5% | 110000-471 | R128 | Resisior, 4 W, 2.2K, 45% | 110000-222 | |
| R34 | Resistor, 4 W, 10K 2, £5% | 140000-103 | R129 | Resistor, % W, 100KQ, +5% | 110000-104 | |
| R35 | Resistor, % W, IK 9, 5% | 110000-102 | R130 | Resistor, 4 W, 47K Q, £5% | 130000475 | |
| R36 | Resistor, 4 W, 2200, +5% | 110000-221 | . | < | | |
RI31-R133. Resistor, 4 W, 100K@, +5% 110000-104
| R37 | Resistor, 4 W, 2209, +5% | 110000-221 | R134 | Resistor, 4 W, 47K Q, 45% | 110000-473 | ||
| R38-R42—Resistor, 4 W,1K 9, +5% | 110000-102 | RIS5-R148_ Resistor, A W, 100K Q, 55% | 110000-104 | ||||
| R43-R58 | Resistor, A W, 10K Q, +5% | 110000-103 | R139 | Resistor, 4 W.47KQ, £5% | 110000-473 | ||
| 9 | ‘stor | & | W. | y | |||
| ™ | Reston, | AWK, $9% | {0000-102 | RIO | Resistor, | W, G8K 2, 45% | 119000-683 |
| ROO-RO? | Resistor, & W, 3.3K M, 45% | 110000:332 | R14], R142. Resistor, 4 W, 47K Q, 45% | 110000-473 | |||
| ROB | Resistor, & W, 1K@, +5% | 119000-102 | R143 | Resistor, 4 W, 68K 2, +5% | 110000-683 | ||
| R69 | Resistor, 4 W, 1.8K 9, 45% | 110000-182 | R144 | Resistor, %& W, 47K 2. 45% | 119000-473 | ||
| R70 | Resistor, 4 W, 10K Q, +5% | 110000-103 |
R148, RI51. Resistor, 4 W, 100K Q, + 5% 110000-104
| R71 | Resistor, 4 W, 5.6K 2, +5% | 110000-562 | R155, RIS6. Resistor, 4 W, 470.2, + 5% | 130000-471 | |
| R72-R74 | Resistor, 4 W,100KQ, +5% | 110000-104 | RIS? | Resistor, 4 W, 10K 2, | 110000-103 |
| 75; | Resistor, | W, 1K Q, +5% | 110000-102 | R158, R159 Resistor, % W,3.3KQ, +5% | 110000-332 |
| . | y | K | 9 | - | |
| R76-R85 | Resistor, 4 W, 10K, +5% | 116900-103 | RIG | Resistor, & W, 1K, £5% | + 10000-102 |
| R86 | Resistor, & W, 2202, +5% | 110000-221 | RI6I | Resistor, 4 W, 1502, £5% | 1100-151 |
| R87 | Resistor, “ W, 2202, +5% | 110000-221 | R162 | Resistor, % W, LOK 2, = | 110000-103 |
| RBS, KBD | —_Resistor, A W.10K 2, 5% | 110000-103 | RIGS | Resistor, 4 W, 3.3K 2, 25% | 110000-332 |
| R90 | Resistor, 4 W, 1009, +5% | 110000-101 |
RIG4, RIGS Resistor, 4 W,1KQ, +5% 110000-102
| ROL | Resistor, 4 W, 4.7K, +5% | 110000-472 | R168, | Resistor, & W, 1KQ, +5% | 110000-102 | |
| ROZ | Resistor, %& W, 1002, +5% | 110900-101 | R169, R170 Resistor, 4 W, 4.7K Q, +5% | 110000-472 | ||
| ROB | Resistor, % W, 4.7K 2, £5% | 110000-472 | RI7I | Resistor, % W, 2709, +5% | 110000-271 | |
| RO4 | Resistor, 4 W, 22K Q, 45% | 119000-223 | ||||
| RITZ | Resistor, 4 W, 122, 45% | 110900-123 | ||||
| ROS | Resistor, 4 W, 47K 9, +5% | 110000-473 | R173 | Resistor, 4 W, 562, +5% | 110000-563 | |
| ROG, | Resistor, 4 W, 100K 2, 25% | 110000-104 | Ri74 | Resistor, 4 W, 10K 2, +5% | 110000-103, | |
| ROT | Resistor, % W, 22K @. +5% | 110000-223 | R175 | Resistor, 4 W, 8.22, +5% | 110000-822 | |
| % | % | . | ||||
| Wo | cielo | saad | R176 | Resistor, 4 W, 3.9K Q, £5% | 110000-392 | |
| R99. | Resistor, 4 W, 100K Q, +5% | 110000-104 | RIT | Resistor, % W, | 470, +5% | 119000-471 |
| R100 | Resistor, 4 W, 22K ®, +5% | 410000-223 | RI78 | Resistor, & W,1KQ. +5% | 110900-102 | |
| RIGL | Resistor, % W, 47K Q, 45% | 110000-473 | R179 | Resistor, 4 W,00, +5% | 110095-001 | |
| R102 | Resistor, 4 W, 100K Q, +5% | 110000-104 | RN1, RN2_— | Resistor Network, SIP, 10K x8, 1/8 W | 11802-1053 | |
| R103 | Resistor, % W, 100K 9, +5% | 110000-104 | Miscellaneous | |||
| R104, R105. Resistor, 4 W, 1K 2, £5% | 110000-102 | VR | Voltage Regulator, Type-7903 | 37-7905 | ||
| R106 | Resistor, 4 W, 100K @, +5% | 110000-104 | YI | Crystal, 20 MHz | 144000-003 | |
| R107, R108 Resistor, 4 W, 18K Q, +5% | 140000-183 | Y2 | Crystal, 14.318 MHz | 90.101 | ||
| ™ | cite 44 | 5% | w.104 | 5168 | Switch, 8 Position, DIP | 160031-008 |
| hi | hee : wen wee | ionoosat | 6I7A | Switch, 8-Position, DIP | 160031.008 | |
| RIL | Resistor, ¥ W, 560.2, +5% | 110000-561 | ||||
| R112 | Resistor, 4 W, 1K Q, +5% | 110000-102 |
“x in the part nianber denvies the revision level
6-21
6-22 Figure 6-9 720° A043922 Video PCB Assembly OL A Illustrated Parts Lists
sGewrnae 3 a a ay AY)S seroma * “asses 1 sm use = ” a 8 Smt gy Heap apres ease Sh | ce ee ee
:
: aS at Sly a i ae oy ah —
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING
CONFIDENTIAL. Reoroduston fobioden wnod tne speciic wen persion of Att Gamgs Corporaten, Milas, Cn Tr dawng\s ony
Ror possession thereat cont:
NOTE:
- DO NOT INSTALL R3 AND C143. 70"
720° Ulustrated Parts Lists
720° Video PCB Assembly Parts List
Desig- Desig:
| nator | Description | Part No. | nator | Description | Part No. |
| Integrated Circuits | aL | TypeolioP-s, 1901s RAM | IA721 1-001 | ||
| 1A | Type-“HLS157 Integrated Circuit | 37-74LS157 | |||
| 1B | = Integrated Circuit | 3M | Type-G116P-4, 150. ny RAM | 1721-01 | |
| 1BIC | “4LS157 Integrated Circuit | Integrated Circuit | |||
| 1c/D | Type-“4LS244 integrated Circuit | B7-TALS244 | aN | 137209-001 |
aP 137420-001
| IDIE | Type-T4L$244 Integeated Circuit | 37-7418244 | ||
| 1EF | 4LS244 Integrated Circuit | 3R | ||
| 1F/H | Type-“4L5245 Integrated Circuit | - | 38 | '4 Integrated Circuit |
| 1H | Type-74L8245 Integrated Circuit | 37-74LS245 | aT | Integrated Circuit? |
4A Type-74804 Integrated Circuit
| ) | Type-74L8244 Integrated Circuit | 37-7418244 | |||
| 1K | Type-7AL$374 Integrated Circuit | 4BIC | Type 6264-15 RAM invegrated Circuit | ||
| IL | Type-74L932 Integrated Circuit | 4ciD | Type 6264-15 RAM Integrated Circuit | 137441-001 | |
| 1M. | Type-74L5244 Integrated Circuit | 37-7415244 | 4DIE | S163 lotegrated Circuit | 37-74LS1634 |
AEF Type-74S74 Integeated Cireuit 5
| IN | ‘Type-7415374 Integrated Circuit | 37-7419374 | |||
| Ip | ‘Type-74L8244 Integrated Circuit | 37-74LS244 | 4FIH | Type-74LS174 Integrated Circuit | 3 |
| IR | Type-74LS244 lategrated Circuit | 37-7418244 | 4H | Type-74L8273 Integrated Circuit | 37-74LS273, |
| 1s | Type-7415244 Integrated Circuit | 37-74L8244 | 4 | 3 Integrated Circuit | 137204-001 |
| 4k | 83 Integrated Circuit | 137204-001 | |||
| IT | ‘Type-74874 Integrated Circuit | 37-74874 | |||
| 2a | Type-7418244 Integrated Circuit | 37-74LS244 | aKNL | Type-74LS273 Integrated Circuit | 37-74L$274 |
| 2B | Type-74LS153 Integrated Circuit | 37-74L5153 | 4M | Type-74F374 Integrated Circuit | 137420-001 |
| 2BIC | ‘Type-74L5374 Integrated Circuit | 37-74LS374 | 4MIN | Type-825131 Programmable PROM | 136034-131 |
Integrated Circuit
| 2c1D | ype-74LS32 Integrated Circuit | 37-74LS32 | 4NIP | Type-74F374 Integrated Circuit? | 137420-001 |
| 2DIE | ‘Type-74L$174 integrated Circuit | 37-74L8174 | |||
| 2EF | ype-74L5153 Integrated Circuit | 37-74LS153 | PIR | Type-7418273 Integrated Circuit | 37-74LS273 |
| 2hH | Type-7415153 Integrated Circuit | 37-74L8153 | 4RIS | Type-74F374 Integrated Circuitt | 137420-001 |
| 4 | Type-27128, EPROM, Integrated Circuit | 136047-x125 | |||
| 2H | Type-74L$153 Integrated Circuit | 37-74L$153 | SA | Type-74LS109 Integrated Circuit | 37-74L5109 |
| 2) | Type-74S174 Integrated Circuit | 137209-001 | |||
| 2k | Type-74S74 Integrated Circuit | 37-74874 | 5B | ‘Type-74S08 Integrated Circuit | 37-74808 |
| 2L | ‘Type-74L5139 Integrated Circuit | 37-741S139 | SBIC | Type-74LS08 Integrated Circuit | 37-741808 |
| ScD | Type-74LS163A Integrated Circuit | 37-TALS1O3A | |||
| 2M | Type-74L$153 Integrated Circuit | 37-74L8153 | SDIE | ‘Type-74L5163A Integrated Circuit | 37-7ALSIG3A |
| 2N | Type-74L$153 Integrated Circuit | 37-74LS153 | |||
| 2P | Type-7415374 Integrated Circuit | 37-74LS374 | SEF | Type-74¥ 163 Integrated Circuit” | 137545-001 |
| 2R | ‘Type-74L9374 Integrated Circuit | 37-7415374 | SHIH | Type-741$04 Integrated Circuit | 37-74L804 |
| SH) | Type-27512, | EPROM, Integrated Circuit | 136047-x108 | ||
| 2s | ‘Type-74L$374 Integrated Circuit | 37-74LS374 | SVK | Type27512, EPROM, Integrated Circuit | 136047-x107 |
| oT | Type-74832 Integrated Circuit | 37-74832 | |||
| 3A | ‘Type-74F374 Integrated Circvitt | 137420001 | SL | Type-27512, EPROM, Integrated Circuit | 136047-x106 |
| 3B | Type-74F374 Integrated Circuitt | 137420001 | 5M | ‘Type-27512, EPROM, Integrated Circuit | 136047-x105 |
| SN | Type-27512, EPROM, Integrated Circuit | 136047-x104 | |||
| 3BIC | Type-74F374 Integrated Circuit | 137420-001 | 5P | Type-27512, EPROM, Integrated Circuit | 136047-x103 |
| 3c/1D | '4L5163A Integrated Circuit | 37-74LS163A | |||
| 3DIE | Type-4LS163A Integrated Circuit | 37-74LS163A | SRS | Type-27512, EPROM, Integrated Circuit, | 136047-x102 |
| BEE | ‘Type-745157 Integrated Circuit | 37-748157 | ST | ‘Type-27512, EPROM, Integrated Circuit | 136047-x101 |
| 6A | ‘Type-27512, EPROM, Integrated Circuit | \36047-x121 | |||
| 3F/H | 741$273 Integrated Circuit | 33-7ALS273 | 6B | Type-27512, EPROM, Integrated Circuit | 136047-x122 |
| 3H | -74L$273 Integrated Circuit | 37-74LS273 | |||
| 3H) | Type-6116P-3, 150 ns RAM | 137211-001 | oc | Type-27259, EPROM, Integrated Circuit | |
| Integrated Circuit | 6D | Type-27512, EPROM, integrated Circuit | |||
| 3K | Type-61 16P-3, 150 ns RAM | 137211-001 | G/TEIE | Type 741832 Integrated Circuit | 2 |
| Integrated Circuit | GFK | Type-74L8174 Integrated Circurt | 37 74LS174 |
“x" in whe part number denvtes the revtston level “Acceptable substitute is Type-74AS163N Integrated Circuit, part no, 13742 O01 t Acceptable substitute is Type-744S374N Integrated Circuit, part no. 137422-U01
Musteated Pacts Lists 720°
720° Video PCB Assembly Parts List, Continued
Desig: Desig-
| nator | Description | Part No. | nator | Description | Part No. |
| EF | Type-74LS163A Integrated Circuit | ST-T4LSIO3A, | BIC | Type-745189 Integrated Circuit | 37-748189 |
| Grr | ‘Type-74L5138 Integrated Circuit | 137177-001 | 9ciD | Type-748189 Integrated Circuit | 37-748 189 |
| OH | 136047-x116 | 9D | ‘Type-745189 Integrated Circuit | 37-745189 | |
| GK | 336047115 | OE | ‘Type-745189 Integrated Circuit | 37-745189 | |
| OL | 136047-x 114 | OF | Type-74L$94 Integrated Circuit | 37-74LS04 | |
| oM | 130047-x1 13 | oH | Type-745153 Integrated Circuit | 137207-001 | |
| 6N | 13604 7-xL12 | 9 | Vype-74L5244 integrated Circuit | 37-7418244 | |
| oP | 130047-x111 | OK | ‘Type-74F374 Integrated Circuitt | 137420-001 | |
| RIS | 136047-x1 10 | ‘Type-74F374 Integrated Circuit | 137420-001 | ||
| or | 12, EPROM, Integrated Circuit. | — 136047-x109 | Type-748244 Integrated Circuit | 137333-001 | |
| 7A | 12, EPROM, Integrated Circuit | 136047-x123 | Type-2149, 35 ns Static RAM | 137199-003, | |
| 7B | 6, EPROM, Integrated Circuit | 136047-x124 | Integrated Circuit | ||
| oP | Type-2149, 35 ns Static RAM | 137199-003 | |||
| 7C | 12, EPROM, Integrated Circuit | 136047-x120 | Integrated Circuit | ||
| on | ype-27512, EPROM, Integrated Circuit, | 136047-x119 | |||
| TENE | Type-74LS00 Integrated Circuit | OR | ‘Type-74F163 Integrated Circuit* | 137345-001 | |
| TRH | ‘Type-74S08 Integrated Circuit | 98 | Type-74F 163 Integrated Circuit” | 137345-001 | |
| oT | Type-74F 163 Integrated Circuit* | 137345-001 | |||
| TH | ‘Type-74L$158 Integrated Circuit | 137203-001 | 10a | ‘Type-745 158 Integrated Circuit | 137312-001 |
| y | Type-74L$158 Integrated Circuit | 137203-001 | |||
| 7K | ‘Type-74S194 Integrated Circuit | 137424001 | 10B | ‘Type-74F374 Integrated Circuitt | 137420-001 |
| TL | Type-745194 Integrated Circuit | 137424-001 | sOBIC | ‘Type-74S00 Integrated Circuit | 37-74800 |
| loc | ‘Type-745283 Integrated Circuit | 137241-001 | |||
| ™M | ‘Type-74LS158 Integrated Circuit | 137203-001 | 10D | ‘Type-745153 Integrated Circuit | 137207-001 |
| IN | ‘Type-74LS158 Integrated Circuit | 137203-001 | |||
| 7 | ‘Type-74S194 Integrated Circuit | 137424001 | 10E, | Type-745153 Integrated Circuit | 137207-001 |
| oR | Type-745194 Integeated Circuit | 137424-001 | 10F | ‘Type-74L8244 Integrated Circuit | 37-74L8244 |
| 10H | ‘Type-74L$244 Integrated Circuit | 37-741S244 | |||
| 1S | Type-74S194 Integrated Circuit | 137424-001 | 10) | Type-74F374 Integrated Circuitt | 137420-001 |
T ‘Type-745194 integrated Circuit ¥
| 8A | Type-745194 Integrated Circuit | 10K | Type-74F374 integrated Circuit | 137420-001 |
| 8B | Type-745194 Integrated Circuit | 10L | Type-74F374 Integrated Circuitt | 137420-001 |
| 10M | ‘Type-748244 Integrated Circuit | 137333-001 | ||
| 8BIC | Type-74S194 Integrated Circuit | 1ON | Type-2149, 35 ns Static RAM | 137199-003 |
| Bcd | Type-745194 Integrated Circuit | Integeated Circuit |
8D Type-74F 163 Integrated Circuit*
| 8E | Type-741S163A Integrated Circuit | 10P | ‘Type-2149, 35 ns Static RAM | 137199-003 |
Integrated Circuit
| 8F | Type-74LS74 Integrated Circuit | 10R | Type-74F1G3 Integrated Circuit* | 137345-001 |
| 8H | Type-748162 Integrated Circuit | 10S | Type-74F163 Integrated Circuit” | 137345-001 |
| 8) | Type-74S194 Integrated Circuit | \0T | ‘Type-74F 163 Integrated Circuit* | 137345-001 |
8L Type-741S20 Integrated Circuit
| A | Type-745189 Integrated Citcuit | 37-748 189 | |||
| 38M | Type-748244 Integeated Circuit | UB | ‘Type-7 45158 integrated Circuit | 1373 12-001 | |
| eM | Type-2 149, 35 ns Static RAM | 1BIC | ‘Type-74S1 12 Integrated Circuit | 137334-001 | |
| Integrated Circuit | cD | ‘Type-74$00 Integrated Circuit | 37-74800 | ||
| 8? | ‘Type-2149, 35 ns Static RAM | 137199003 | |||
| Integrated Circuit | 1D | ‘Type-74808 Integrated Circuit | 37-74808 | ||
| BR | Type-74F163 Integrated Circuit | 137355-001 | HE | Tepe-"48153 Integrated Circuit | 137207-001 |
| UE | ‘Type2149, 45 ns Static RAM | 137199-002 | |||
| 8s | Type-7aF 163 Integrated Circuit* | Integrated Circuit | |||
| sT | Type-74F163 Integrated Circuit* | 137345-001 | wk | Type-2149, 45 8 Static RAM | 137199-002 |
| 9A | Type-748189 Imegrated Circuit | 3774s189) | Integrated Circuit | ||
| 9B | Type-748158 Integrated Circuit | 187312001 |
x in the part number denotes the revision level “Acceptable substitute is Type-74AS163 tAcceptuble substitute is Type. puegrated Circuit, part no. 137421-001 "4N Integrated Circuit, part no. 137422-001
720°
720° Video PCB Assembly Parts List, Continued Mlustrated Parts Lists
Desig Desig-
| nator | Description | PartNo. | nator | Description | Part No. | |
| uy | Type-2149, 35 ns Static RAM | 13719-0902 | ci4 | Capacitor, Ceramic, 100 pk. 100 V | [2016-101 | |
| Integrated Circuit | cs | Capacitor, Ceramic, .1 ef, 50V | 122002-104 | |||
| MK | Type-2149, 45 ns Static RAM | 137199-002 | C16 | Capacitor, | Ceramic, 100 pF, 100 V | 122016-101 |
| Integrated Circuit | cn | Capacitor, Ceramic, .1 pF. 50 | 122002-104 | |||
| ML | ‘Type-74832 Integrated Circuit | 37-4832 | ||||
| MM | ‘Type-74520 Integrated Circuit | 137423-001 | cis | Capacitor, Ceramic, 100 pF, 100 | 12010-1014 |
€19-C138 — Capacitor, Ceramic, .1 uF, 50 V 2002-104
| IN | Type-74F10 Integrated Circuit | 137428-001 | C139-Clal | Capacitor, Ceramic, .001 zF 50 V | 122002-102 |
| uP | ‘Type-74586 Integrated Circuit | 137002-001 | C144-C147 Capacitor, Ceramic, .1 wf. 50 V | 122002.104 | |
| IIR | Type-74LS32 Integrated Circuit | 37-74L832 | |||
| 1s | Type-74LS08 Integrated Circuit | 37-74LS08 | Connectors | ||
| 3 | Connector. Header, 11-Circuit | 179014011 | |||
| ut | Type-741$32 Integrated Circuit | 37-741832 | 156 Ctr, Pol | ||
| 12a | Type-74874 Integrated Circuit | 37-74874 | Jig | Connector, Header, Sq. Pin, | 179118011 |
| 12B | Type-74510 Integrated Circuit | 137236-001 | 11-Circuit, .100 Ctr | ||
| 12B/C | Type-74504 Integrated Circuit | 37:74504 | JP1-JP6 | Connector, Header, 6 Ckt. (2 rows x3 | 179177-006 |
Ckt.), 100 Ctr
| 120/10 | ‘Type-74574 Integrated Circuit | 37-74874 | JPI-\P6 | Connector, Receptacle, 2 Ckt | 179178.002 |
| 12D | Type-74820 integrated Circuit | 137423-001 | |||
| IE | Type-745174 Integrated Circuit | 137209-001 | Ferrite Beads and Inductors | ||
| QE | Type-74L5174 Imegrated Circuit | 37-74L8174 | Lu | Inducter, 1 wH | 141007-001 |
| 12-14 | Ferrite Bead | 141003-005 | |||
| 12H | ‘Type-74F374 Integrated Circvitt | 137420-001 | Ls. | Inductor, 100 pH | 141019-001 |
| 12) | ‘Type-74F374 integrated Circuit | 137420-001 | |||
| 12K | ‘Type-74F374 Integrated Circuit | 137420-001 | Transistors | ||
| 1b | Type-7406 Integrated Circuit | 37-7406 | wQ | ‘Type-2N3904 Transistor | 34-2N3904 |
| @ | ‘Type-2N3906 Transistor | 33-2N3906 | |||
| 13A | Type-74LS74 Integrated Circuit | 37-74LS74 | oy) | Type-2N3904 Transistor | 34-2N3904 |
| 13B | ‘Type-74S112 Integrated Circuit | 137334-001 | QO | Type-2N3906 Transistor | 33-2N3906 |
| 1BBIC | Type-741$32 Integrated Circuit | 37-74LS32 | |||
| BCD | Type-7415260 Integrated Circuit | 137332-001 | 6,Q7 | Type-2N3004 Transistor |
Q8 Type-2N3906 Transistor
| 13D | Type-7407 Imegrated Circuit | 37-7407 | Q9,Q10 | ——Type-2N3904 Transistor | |
| 1BE | Type-74S174 Inegrated Circuit | 137209-001 | Qu | ‘Type-2N3906 Transistor | |
| 1BF | Type-74LS08 Integrated Circuit | 37-74LS08 | a2 | ‘Type-2N3904 Transistor | 34-2N3904 |
| 13K | ‘Type-74F374 Integrated Circuitt | 137420-001 |
Resistors
| 13) | Type-74L5260 integrated Circuit | 137332-001 | RI | 1502, £5%, 4 W Resistor | 140000-151 |
| 13K | Type-7406 Integrated Circuit | 37-7406 | R2 | 10K 9, +5%, % W Resistor | 110000-103 |
| 134 | Type-7406 Integrated Circuit | 37-7406 | R4 | 68.2, +5%, 4 W Resistor | 110000-680 |
| RIT.RI8 | 2200, +5%, & W Resistor | 110000-221 |
Sockets
| 28-Contact, Medium-Inserion-Force IC | 79-4228 | RIS | 1KQ, +5%, 4 W Resistor | 110000-102 | |
| Socket | R20 | 1200, £5%. 4 W Resistor | 110000-121 | ||
| R21, R22 | 5%, & W Resistor | 110090-181 | |||
| Capacitors | R23 | i, MW Resistor | 110000-221 | ||
| €1,C2 | Capacitor, Aluminum, 100 wR, 35 V | 24-350107 | |||
| 3, C4 | Capacitor, Ceramic, .1 pF, 50 V | 122002-104 | R24 | 4702, +5%, %& W Resistor | 1000-471 |
| cS | Capacitor, Aluminum, 100 uF, 35 V | 24-350107 | R25 | 1KQ, £5%, 4 W Resistor | 110006-102 |
| 7 | Capacitor, Electrolytic, 1 uF, 50 | 24-500105 | R26 | 2KQ, + 5%, MW Resistor | 110008-202 |
| R27 | 1569, +5%, \& W Resistor | 110000-151 | |||
| cB | Capacitor, Ceramic, .1 x, SOV | 122002-104 | |||
| for) | Capacitor, Mica, 47 pF, 100 V | 128002-470 | R28 | 3.9K 2, +5%, & W Resistor | 110000-392 |
| clo | Capacitor, Mica, 68 pF, 100 V | 128002-680 | R29 | 3902, 45%, %& W Resistor | 110008-391 |
| C1I-C13 | Capacitor, Ceramic, .1 pF, 50 V. | 122002-104 | R30 | 6BQ, +5%, 4 W Resistor | 11 0000-680 |
| R31 | 4709, | £5%, & W Resistor | 310000-473 |
°x"' in the part number denotes the revision level “Acceptable substitute is Type-74AS163N Integrated Circuit, part no, 137421-001 +tAcceplable substitute is Type-74AS374N Integrated Circuit, part no, 137422-001
Glusteated Parts Lists 720°
720° Video PCB Assembly Parts List, Continued
Desig- Desig:
| nator | Description | Part No. | nator | Description | Part No. | |
| R32 | 680, £5%, | A W Resistor | 110000-680 | R55 | 680, +5%, 4 W Resistor | 410000-680 |
| R33 | 10Q, +5%, 4 W Resistor | 110000-100 | R56 | 4702, +5%, 4 W Resistor | 110000-471 | |
| RY | 6200, + 5%, 14 W Resistor | (10000-621 | ||||
| R35 | 1.2KQ, £5%, | & W Resistor | 110000-122 | R57 | 689, +5%, % W Resistor | 110000-680 |
| R58 | 109, £5%, 4 W Resistor | 110000-100 | ||||
| R36 | M4 W Resistor | 110000-242 | R59 | 620.0, + 5%, & W Resistor | 110000-62t | |
| Rs- | 410000512 | ROO | 12KQ, £5%, %& W Resistor | 110000-122 |
RAB 119000-821
| R39 | 1 100900-103 | R61 | 24K Q, £5%, 4 W Resistor | 110000-242 | ||
| R62 | 5.1K Q, | £5%, %& W Resistor | 110000-512 | |||
| R40, RAL | 160.0, £5%, a W Resistor | 410000-161 | ROS | 8202, £5%, & W Resistor | 110000-821 | |
| RaQ | 3900, 25%. 4 W Resistor | 110000-394 | RO4 | 10K Q, + 5%, & W Resistor | 110000-103, | |
| Ra3 | 680, | 25%, | 4 W Resisior | 110000-680 | ||
| Rad | 4700, 45%, % W Resistor | 110000-471 | ROS-R75 | KM, £5%, 4 W Resistor | 110000-102 | |
| R78 | 2209, +5%, & W Resistor | 11000-221 | ||||
| a5, | 68.2, +5%, & W Resistor | 110000-680 | R79-RB1_ | 4702, 45%, Ye W Resistor | 110000-471 | |
| RAG | 109, | 45%, % W Resistor | 110000-100 | RNI,RN2 | Resistor Network, SIP, 680@ x 7 | 118007-681 |
| Ra? | 620.2, 45%, % W Resistor | 110000-621 | ||||
| R48 | 1.2K Q, £5%, % W Resistor | 110000-122 | Miscellaneous | |||
| C142 | Filter, Feed-Thru, 2000p#, 154 | 140002-001 | ||||
| Rag | 24K 9, +£5%, & W Resistor | 110000-242 | CRI | Diode, Light-Emitting, Type-MV5053 | 38-MV5053 | |
| R50 | 5.1K Q, 5%, 4 W Resistor | 110000512 | TAB | Terminal, Fast-On (Acceptable substitute | 179051-002 | |
| RSI | 8200, £5%, 4 W Resistor | 130000-821 | is Test Point, part no. 020670-001) | |||
| R52 | 10K Q, | 5%, % W Resistor | 110000-103 | YI | Crystal, 32 MHz, | 144003-002 |
Terminal, Ring Lug, #8, Solder Tab 179005-002
| R53 | 160.2, +5%, A W Resistor | 110000-161 |
| R54 | 3909, £5%, 4 W Resistor | 110000-391 |
6-26 ("in the part number denotes the revi
- Acceptable substitute is Type-T4AS163 + Acceptable substitute is Type-7 ston level N Integrated Circuit, part no. 137421-001 J Integrated Circuit, part no. 137422-001
Ullustrated Parts Lists,
|ONS RECEIVING THIS DRAWING
n permission of Atari Games Corporation, Mipvtas, CA This drawing is only
C18 Ci8-A Et C17 C17-A
Cc 3300UF SPL c2 [_} swt C CT]
JAUX JC
res
is) ley
R14
ane) R3 oO zo uo
~—+
ioe) ze oo CC2- Oo
cc2+ a
CCi+ oO CCia
CR13 C7 CR D 720°
6-27 Figure 6-10 Audio II PCB Assembly A043661-01 B
Warranty
Seller warrants that its printed-circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment Seller warrants that its video displays and laser video disc players (in games supplied with displays and video-disc players) are free {rom defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment. None of the Seller's other products or parts thereof are warranted. If the products described in this manual fail to conform to this warranty, Seller's sole liability shall be, at its option, to repair, replace, or credit Buyer's account for such products which are returned. to Seller during said wartanty period, provided: {a) Seller is promptly notified in writing upon discovery by Buyer that said products are defective;
- Such products are returned prepaid to Seller's plant; and
- Seller’s examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation, or improper testing Inno event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages. Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms herein, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller's part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products by Seller.
The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to you and others. Be very cautious in using non-Atati-supplied components with our games, in order to ensure your Safety. Atari distributors are independent, being privately owned and operated. in their judgment they may sell parts or accessories other than Atari parts or accessories. Atari Games Corporation cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor,
_ (408) 434-3950 Fax 408 434 3945 Telex 5101007850 P.O. Box 361110 ;