CATHODE RAY TOMES

Black Widow TM-234 2nd Printing

Black Widow (Atari, 1982) · Technical Manual · 60 pages · 41 sections · original scan

Page 1

Operators Manual

© 1983 Atari, Inc. All Rights Reserved

Page 2

If reading through this manual does not lead to solving a certain maintenance prob-

lem, call TELEHELP® at the Atari Customer Service office in your geographical

area, as shown below. WEST and CENTRAL U.S.A. Parts and Service

Page 3
Scan of page 3

This page is a drawing, shown as the original scan.

Page 4

Black Widow

© 1983 by Atari, Inc. All rights reserved. No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher. The game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the U.S. Copyright Act of 1976. This Act provides for increased penalties for violating federal copyright laws. Courts can impound infringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articies. In addition, the Act provides tor payment of statutory damages of up to $50,000 in certain cases. Infringers may also have to pay costs and attorneys’ fees, fines up to $25,000, and face an imprisonment of up to one year. Atari will aggressively enforce its copyrights against any infringers. We will use all legal means to immediately halt any manufacture, distribution, or operation of a copy of video games made by us. Anyone who purchases such copies risks forfeiting such a game.

Published by: ATARI, INC. 790 Sycamore Drive P.O. Box 906 Milpitas, California 95035

Printed in the U.S.A. 3M -

Page 5

Notice Regarding Non-ATARI Parts

WARNING

Use of non-ATARI parts or modifications of your ATARI game circuitry may adversely affect the safety of your game, and injure you or your players.

You may void the game warranty (printed on the inside back cover of this manual) if you do any of the following: ¢ Substitute non-ATARI parts in the game © Modify or alter any circuits in the game by using kits or parts not supplied by Atari.

FERENC

to licensed communications services is not permitted by the FCC (Federal Communications Commission).

|f you suspect interference from an ATARI game at your location, check the following: @ All grounds (green wires) in the game are properly connected as shown in the game wiring diagram, and @ The power cord is properly plugged into a grounded 3-wire outlet. If you are unable to solve the interference problem, please contact ATARI Customer Service. See page vi for service in your area. Black Widow

Page 6

Black Widow

Table of Contents

1 Set-Up Procedures A. How to Use This Manual... ... 06.02.00 cece cece ee eee teen eee 11 B. Game Overview. ........ 2 43 C. installation Specifications 13 D.. Inspecting the Game ........... 13 E. Voltage-Plug Selection and Fuses . we 14 F. Switch Locations ..... 1 45 Power On/Off Switch 15 Utility Panel Switches 1-5 Option Switches .... - 45 G. Selecting the Options ......... 0... cee eee eee eens 1-6

2 Self-Test Procedure A. Obtaining the Operator Information Display...............6 2-2 B. Obtaining the Self-Test Displays 2-2 3 Illustrated Parts Lists A. Cabinet-Mounted Assemblies 32 B. Control Panel Assembly. .... 3-4 C. Fluorescent Tube and Speaker. . 3-8 D. Video Displays ........... . 39 E. Utility Panel Assembly. . #12 F. Coin Door Assemblies . 313 G. PowerSupply Assembly. . 3-20 H, Printed-Circuit Boards ........ 0... cece eee eee eee teenies 3-22

Page 7

Figure 1-1 Figure 1-2 Figure 1-3

Figure 2-1 Figure 2-2 Figure 2-3 Figure 2-4 Figure 2-5 Figure 2-6 Figure 2-7 Figure 2-8 Figure 2-9

Figure 3-1 Figure 3-2 Figure 3-3 Figure 3-4 Figure 3-5 Figure 3-6 Figure 3-7 Figure 3-8 Figure 3-9 Figure 3-10 Figure 3-11 Figure 3-12 Figure 3-13

Table 1-1 Table 1-2 Table 1-3 Table 1-4

Table 2-1 Table 2-2 Table 2-3 Table 2-4 Black Widow

List of Illustrations

Voltage-Selection Plug and Fuse Locations . Switch Locations

Operator information Display. Screen 1—Test Passes . Screen 1—Test Fails . Screen2......... Screen3 .. Screen4 .. Screen .. Screen6 .. Screen 7—Diagnostic Program Displays ...

Cabinet-Mounted Assemblies ........-....... eee e eee rene Control Panel Assembly. ..... = 8-Position Joystick Assembly. . Fluorescent Tube and Speaker Wells-Gardner Video Display . . Amplifone Video Display . Utility Panel Assembly . . . Vertically Mounted Coin Door . American-Made Coin Door... . Color X-Y Power Supply Assembly . PCB Mounting Hardware .........- 00.00.0000 Black Widow Game Printed-Circuit Board Assembly . oe Regulator/Audio Il PCBAssembly .............. 000 cece eee

Installation Specifications ........ 0... cece eet eee eee Switch Settings for Price Options os Switch Settings for Special Options . Switch Settings for Bonus and Difficu

RAM Locations ROM Locations EAROM and Custom I/O Chip Vector-Generator Diagnostic Tests

Page 8

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 9

Set-Up Procedures

A. How to Use this

Manual

This manual, written for game operators and service technicians, describes the Black Widow Upright game. Chapter 1 contains game specifications, inspection procedures, voltage plug and fuse information, switch locations, and option information. Chapter 2 contains self-test procedures. Chapter 3 contains illustrated parts lists. Figures 1-1 and 3-1 illustrate the Upright game cabinet. These figures refer you to other places in the manual for more information about specific cabinet parts.

Chapter

Page 10

Set-Up Procedures

Video Display * See Figures 3-5 & 3-6

Coin Door Assy. See Figures 3-8 & 3-9 Attraction Panel See Figure 3-4

Joystick Assy. See Figure 3-3 Control Panel Assy.. See Figure 3-2

Speaker

Utility Panel Assy. See Figure 3-7

WARNING Shock Hazard Do not plug in the game until it has been inspected. This game should only be connected to a grounded 3wire outlet. if you have only a 2-wire outlet, we recommend you hire a licensed electrician to install a grounded outlet. Players may receive an electrical shock if this. game is not property grounded! Black Widow

Fluorescent Tube & Speaker See Figure 3-4

Game PCB x See Figures 3-11 & 3-12

Regulator! Audio It PCB x See Figures 3-11 & 3-13

POWER ON/OFF SWITCH Power Supply See Figure 3-10

x (tem with a seria! number label

Game Overview

Page 11

Black Widow

B. Game Overview

Black Widow challenges you, the spider, to defend your web from mosquitoes, beetles, hornets, and other insects. Use two joysticks to avoid or shoot enemies and bugs. Watch out for the grenade, rocket bug, thunder bug, spoiler, and collect the grubstakes for extra points! Skill Step™, the Atari feature that allows players to start consecutive games at higher levels, offers players continual challenge. All major parts of the Black Widow game are illustrated in Figure 1-1.

C. Installation Specifications

Table 1-1 describes the physical, electrical, and environmental specifications of the game.

Table 1-1 Installation Specifications

Power 200 W Temperature 0° to +38° C (+32° to + 100° F) Humidity Not to exceed 95% relative Height 184 cm (72% in.) Space Required 64 x 80 cm (25¥2 x 31% in.)

D. Inspecting the Game

Please inspect your game carefully to ensure that it was delivered to you in good condition.

WARNING Shock Hazard To avoid electrical shock, do not plug in the game until the procedures in Sections D and E have been completed! Do not touch internal parts of the display with your hands or with metal objects held in your hands! Set-Up Procedures

Examine the exterior of the game cabinet for dents, chips, or broken parts. Remove the screws from the rear access panel. Unlock and open this panel and the coin door. Inspect the interior of the game as follows: a Ensure that all plug-in connectors (on the game harnesses) are firmly plugged in. Replug any connectors found unplugged. Do not force connectors together. The connectors are keyed so they only fit in the proper orientation. A reversed edge connector may damage a PCB and will void your warranty. Ensure that all plug-in integrated circuits on the PCB are firmly plugged into their sockets. Remove the tie-wrap that secures the coiled power cord inside the cabinet. Inspect the power cord for any cuts or dents in the insulation. Repair or replace it as required. Place the square strain-relief plate in the wood slot at the bottom of the rear panel opening. Inspect major subassemblies, such as the power supply, control panel, and video display. Make sure they are mounted securely and that the green ground wires are connected.

1-3

Page 12

Set-Up Procedures

E. Voltage-Plug Selec-

E. Voltage-Plug Selec tion and Fuses

The power supply in your game contains six fuses. When you replace a fuse, use the identical type fuse with the same electrical rating (see Figure 1-2). The power supply operates on the line voltage of many countries. The power supply comes with either one, two, or three voitage-selection plugs. Plug voltages and wire colors are 100 VAC (violet wire color), 120 VAC (yellow wire color), 220 VAC (blue wire color), and 240 VAC (brown wire color).

Fuse F2 (4A, 250 V)

Fuse F3 (20 A, 32 V)

Fuses F4-F6 (4, 250 Vj Black Widow

See Figure 1-2 for placement of the voltage-selection plug. Before plugging in your game, check your line voltage. Next, check the wire color on the voitage-selection plug. Make sure the voitage-selection plug is correct for the voltage of your location. Now piug the game into a grounded 3-wire outlet.

Voltage-Selection Plug

(7 A, 250 V)

Fuse cover not shown.

Figure 1-2 Voltage-Selection Plug and Fuse Locations

1-4

Page 13

Black Widow

F. Switch Locations

Power On/Off Switch

The power on/off switch is located on the back of the cabinet on the lower left side (see Figure 1-3).

Utility Panel Switches

The volume control, coin counter, self-test switch, and auxiliary coin switch are on the utility panel. The utility panel is located inside the upper coin door (see Figure 1-3). The volume control adjusts the level of sound produced by the game. The coin counter

Utility Panel

Coin Counter

Voiume Control (To increase, turn clockwise) Power On/Off Switch Set-Up Procedures

records the number of coins entered into the game. The self-test switch initiates and stops the self-test mode. The auxiliary coin switch is used to credit the game without activating a coin counter.

Option Switches Option switches for game price, number of lives, bonus, and difficulty selection are on the CPU printed-circuit board (PCB). These switches are at locations D4, B4, and P10/11 (see Figure 1-3).

Switch at B4 (Game Price)

Switch at D4 (Game Play)

Switch at P10/11 (Special Options)

Figure 1-3 Switch Locations

Page 14

Set-Up Procedures

G. Selecting the Options

Settings of the option switches are explained in Tables 1-2, 1-3, and 1-4. Options preset at the factory are shown by the <4 symbol. However, you may change the settings to suit your needs. To verify option switch settings, turn the game off and back on. Then set the self-test switch to on and verify the option switch settings on the self-test dis- Play as described in Chapter 2, A. Obtaining the Operator Information Display. Table 1-2 describes the settings for the 8-toggie switch at location D4. This switch selects the game price options, the coin mechanism multipliers, and the bonus play options. The coin mechanism is a device on the inside of the coin door that inspects the coin to determine if the correct coin has been inserted. After this inspection, the mechanism either accepts or rejects the coin. Black Widow

The multipliers (D4 switches 4-6) determine how much each coin mechanism will be worth to the game’s logic. The coin door has two mechanisms. The basic unit of measurement is a coin worth $.25 or 1 DM, which equals a multiplier of x1. Thus, if you have a 2 DM/1 DM coin door with two coin counters, set switch 8 at location D4 to on and switches 5 and 6 to off. You may offer bonus play for certain combinations of coins inserted into the game. For example, with the game set at $.25 per play, players who deposit four successive quarters, then press the start switch, can recieve a bonus play. The bonus feature encourages players to insert more money than just the minimum required for one game. Ail coins must be inserted before pressing the start switch.

Table 1-2 Switch Settings for Price Options

Settings of &-Toggle Switch on Black Widow CPU PCB (at D4) 8 7 6 5 4 3 2 1 Option

Off Off

On On

Off Off On Off

Off “On

On On

Off On

On On

On On

1 coin/1 credit 1 coini2 credits 2 coins/1 credit Free play

Right coin mechanism x 14 Right coin mechanism x 4 Right coin mechanism x 5 Right coin mechanism x 6

Left coin mechanism x 1 Left coin mechanism x 2 Off No bonus coins (0)* On No bonus coins (6) On No bonus coins (7)

Off For every 2 coins inserted, logic adds 1 more coin (1) Oft For every 4 coins inserted, logic adds 1 more coin (2) Off For every 4 coins inserted, logic adds 2 more coins (3) On For every 5 coins inserted, logic adds 1 more coin (4) On For every 3 coins inserted, logic adds 1 more coin (6)

*The numbers in parentheses will appear on the BONUS ADDER line in the Operator Information Display (Figure 2-1) for these settings. “Manufacturer's recommended setting

Page 15

Black Widow

Table 1-3 describes the settings for the 4-toggle switch at location P10/11. This switch selects Set-Up Procedures

whether credited coins are counted on one or on both coin counters.

Table 1-3 Switch Settings for Special Options

Settings of 4-Toggle Switch on Black Widow CPU PCB (at P10/11) 4 3 2 1 Option

On Off

Table 1-4 describes the settings for the 8-toggle switch at location B4. This switch selects the Credits counted on one coin counter Credits counted on two separate coin counters

game’s starting level, bonus spiders, and difficulty level.

Table 1-4 Switch Settings for Bonus and Difficulty Options

Settings of 4-Toggle Switch on Black Wid 8 7 6 5 4 low CPU PCI B (at B4) Option

Off Off Off On

On Off

On On

On Off

On On

Off

Off On Off Off On

Off On Off On Off Off On On Maximum start at level 13 Maximum start at level 214 Maximum start at level 37 Maximum start at level 53

3 spiders per game<¢ 4 spiders per game 5 spiders per game 6 spiders per game

Easy game play Medium game play Hard game play Demonstration mode

Bonus spider every 20,000 points Bonus spider every 30,000 points Bonus spider every 40,000 points No bonus

4Manufacturer's recommended setting

1-7

Page 16

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 17

Self-Test Procedure

This game will test itself and provide data to show that the game circuitry and controls are operating properly. Self-test data is presented visually on the video display and audibly through the speakers. No additional equipment is required. We suggest that you perform the self-test procedure when you first set up the game, each time you collect money, when you change the game options, when you erase scores and times, or when you suspect a game failure.

Chapter

Page 18

Self-Test Procedures

A. Obtaining the Operator Informa tion Display

Operator Informa-

Set the self-test switch to the on position (refer to Figure 1-3 for the location of the self-test switch). Patterns will appear on the display for a few seconds, then an operator information display will appear as shown in Figure 2-1. The operator information display shows the game statistics and certain game option information. The information display is also used to erase game scores and times as described in the following procedure. All credits are cancelled when the self-test switch is turned on. If the message EAROM BUSY PLEASE WAIT appears, wait for it to disappear before proceeding.

NOTE The BONUS ADDER number (0 through 7) displayed indicates the price option selected by the option switch at location D4. Refer to Table 1-2 in Chapter 1, Switch Settings for Price Options, for the price option settings represented by the BO- NUS ADDER number.

HOLD FIRE THEN PRESS START | FOR TEST LIVES PER GAME 3 MAX START WAVE 21 GAMES PLAYED ' AVERAGE GAME TIME 124 LEFT MECH xi RIGHT MECH XI! BONUS ADCER O MEDIUM BONUS SPICER EVERY eno000 i CHIN | PLAY

Figure 2-1 Operator Information Display

To Erase Scores and Times:

  • Obtain an operator information display as shown in Figure 2-1 by setting the self-test switch to the on position.
  • Press the 1-player start button until the screen displays the appropriate instruction, i.e., HOLD FIRE THEN PRESS START 1 TO (CLEAR SCORES) (CLEAR TIMES) (CLEAR TIMES AND SCORES).

2-2 Black Widow

Hold FIRE joystick forward, then press the 1-player start button. The words EAROM BUSY PLEASE WAIT will appear on the screen until the entire table is erased. Wait until the display disappears before proceeding.

  • Set the self-test switch to the off position to erase the operator information display.

B. Obtaining the Self-

B. Obtaining the Self Test Display

The following information includes instructions for obtaining various self-test displays. These displays are provided to quickly check the game’s operation and locate malfunctions in the game controls and circuitry. If there is a failure, the game produces audiovisual indications to help you find the problem.

NOTE This procedure does not test the coin door lockout coils and coin counter. If the lockeut coils do not energize when the game is on, suspect the lockout coil wiring, coin door harness, game PCB harness, latch R9, or driver Q2 of the game PCB. Troubieshoot using the game schematics.

SCREEN 1 The screen 1 display shown in Figure 2-2 is obtained by setting the self-test switch to the on position. Then hold the FIRE joystick forward and press ithe 1-player start button. If the test passes, the display will go blank for a few seconds before displaying screen 1. This display indicates the condition of the ROM, RAM, and three other integrated circuits.

Page 19

Black Widow

Switch at D4 (Coin modes) ‘Switch Switch Toggle & Toggle 1

Right Coin Mechanism

Left Coin. Mechanism Self-Test Procedures

Switch at B4 (Game piay)

Self-Test Switch

Start Switch (2 playen

Figure 2-2 Screen 1—Test Passes

RAM failure is indicated by a sound and, if possible, an R displayed in the top center of the screen. Count the tones, One or two tones indicates RAM failure at game PCB location N/P1. Three or four tones Indicate RAM failure at game PCB location K7 (see Table 2-1). .

Table 2-1 RAM Locations

Number of Tones RAM Location on Game PCB

1or2 N/P1 3or4 K7

ROM failure is indicated by one or more vertically arranged numbers displayed on the top half of the screen (see Figure 2-3 ). Use Table 2-2 to identify the bad ROM and determine its location. Table 2-2 ROM Locations

Screen Display ROM Location on Game PCB

o* L7 ah MIN7 2° NIP7 3 R7 4 01 5 EIF1 6 H1 7 J 8 K/L1 gre M1

“if this ROM is bad, you will hear a constant low tone and the program may be unable to display a screen image. **if this ROM is bad, the screen may be blank.

Page 20

Self-Test Procedures

EAROM or CUSTOM I/O CHIP failure is indicated by one letter in the top center of the screen. Use Table 2-3 to identify the bad IC and determine its location.

Table 2-3 EAROM and Custom i/O Chip Locations

Screen Display Chip Location on Game PCB

E EAROM at M2 Q Custom /O chip at C/D3 P Custom /O chip at B3

SWITCH failure is indicated by the associated 0 not changing to a 1.on the screen and no sound being produced when the switch is activated. SOUND failure is indicated by no sound, Check the volume control on the utility panel, or troubleshoot using the game schematics.

‘oooldiia

Figure 2-3 Screen 1—Test Fails

To see self-test screens 2 through 6, press the auxiliary coin switch on the utility panel once to advance to the next-screen.

SCREEN 2 A white diagonal grid pattem and a complete character set appear on the screen (see Figure 2-4). The edges of the grid pattern should touch the sides of the screen. If the display is not centered, symmetrical, or the proper size, adjust the X SIZE, Y SIZE, X CTR, Y CTR, X LIN, or Y LIN potentiometers on the gare PCB (refer to the Schematic Package). If the characters are incorrect, check again for a 2 displayed in the preceding ROM failure test (Screen 1),

2-4 Black Widow

g Figure 2-4 Screen 2

SCREEN 3 A white box of decreasing size appears during this test. The box should shrink smoothly. There are seven stages, each with a tone. This pattern tests the binary and linear scaling circuitry. Troubleshoot using the game schematics.

Figure 25 Screen 3

SCREEN 4 A Series of horizontal lines are visible in the middie of the screen. This is a raster test, used by the manufacturer only, to set the color levels.

Page 21

Black Widow

Figure 2-6 Screen 4

SCREEN 5 This test checks the seven screen colors and six intensities of each color (see Figure 2-7). If the intensities do not progress from dim at the top of each color group to bright at the bottom, suspect a problem in the Z-axis of the game PCB or the video display. Use this pattern for the display tracking adjustments (refer to the color X-Y display manual).

RED (R) ROYAL BLUE (8) GREEN (G) \__ \

WHITE (RGB) —>

YELLOW (RG) LIGHT BLUE(GB) LAVENDER (RB)

Figure 2-7 Screen 5 Self-Test Procedures

SCREEN 6 A grid pattern touches the corners of the video display (see Figure 2-8). Press the 1-player start button to change colors. Use this pattern for the display purity and convergénce adjustments (refer to the color X-Y display manual).

Figure 2-8 Screen 6

Page 22

Selt-Test Procedures

SCREEN 7 Screen 7 display comprises a diagnostic program controlled by switches 2, 3, and 4 of the 4-toggle option switch at location P10/11 on the game PCB. This group of switches lets you choose one of six tests. These tests provide recurring sequences to make it easy for you to troubleshoot the vector-generator circuitry. The tests and their respective option switch settings are given in Table 2-4. Black Widow

To display this screen, hold the auxiliary coin switch down, then press the 2-piayer start button. To exit from this screen, set the self-test switch to off. During this test, the screen will either be blank or display vectors, depending on the settings of the switches at location P10/11 on the game PCB. Figure 2-9 shows these screens.

Table 2-4 Vector-Generator Diagnostic Tests

Settings of 4Position DIP Switch at P10/11

TestAction432
Test 1Tests WODIS every 4 msec (blank screen)OffOffOff
Test 2Tesis vector-generator halt instruction every .55OnOffOff

msec (blank screen)

Test 3Tests vector-generator long vector (and halt in-OffOnOff

struction) every 8.2 msec

Tesi 4Tests vector-generator jump instruction (and tongOnOnOff

vector and hait instruction) every 8.2 msec

Test 5Tests vector-generator short vector instructionOffOffOn

{and all of Test 4) every 8.6 msec

Test 6Tests vector-generator JSRL/RTSL instructionOnOffOn

{and all of Test 5) every 10.2 msec

Test 2Blank screenOffOnOn
Test 2Blank screenOnOnOn

TEST 3 TEST 4

TEST 5 TEST 6

Figure 2:9 Screen 7—Diagnostic Program Displays

Page 23

Illustrated Parts Lists

This chapter provides information to order parts for your game. Common hardware (screws, nuts, washers, etc.) has been deleted from most of the parts lists. However, a parts list for the hardware needed to mount the game and Regulator/Audio |! printed-circuit boards to the cabinet has been included. The PCB parts lists are arranged in alphabetical order by component type. Each component subsection is arranged alphanumerically by reference designator. Other parts lists are arranged aiphanumericaily by Atari part number. In these parts lists, all A- prefix numbers come first. Following these are numbers in sequence evaluated up to the hyphen, namely 00through 99 then 000598- through approximately 201000-. When ordering parts, please give the part number, part name, number of this manual, and serial number of your game (see Figure 1-1 for locations of serial numbers.) This will aid in filling your order rapidly and correctly. We hope the results will be less downtime and more profit from your game. Atari Customer Service numbers are listed on the inside front cover of this manual for your convenience.

Chapter

Page 24

Illustrated Parts Lists Black Widow

A. Cabinet-Mounted Assemblies

Fluor. Tube & Speaker Assy. 178034-024 see Figure 3-4 (Fmolding) 03733201 (Vent. grille) ‘A038164-01 (Cabinet assy.) 78-6900402 ~ (Tape) | : 74-2110 (Lock) | 037419-02 (Access panel)

Video Dis; See Figures 3-5 & 3-6

178013-001 (Latch)

Control Panel Assy. See Figure 3-2 Game PCB Assy. ees See Figures 3-11 & 3-12 A038586-01 037308-01 (Main harn. assy.) (Speaker gritle) 148001-017 (Speaker) Regulator/ Audio I! PCB See Figures 3-11 & 3-13

A038588-01 seo Figures 388 99 (Power harn. assy)

‘A037453-03, A037454-03, A037455-03, or Power Supply Assy. 403778403 Utility Pénel Assy. i See Figure 3-10 (Power cord) See Figure 3-7 178048-001 ‘A037470-01 (Caster) (Onloff switch assy.) 009992-01 (On/off switch cover) 78-3201 (Glide)

Figure 3-1 Cabinet-Mounted Assemblies

Page 25

Black Widow Illustrated Parts Lists

Cabinet-Mounted Assemblies Parts List

Part No. Description

A002465-01 Coin Counter

A037453-03Strain-Relief Power Cord(U.S. and Canada)
A037455-03Strain-Relief Power Cord(Australia and New Zealand)

A037470-01 Power On/Off Switch/Mounting Plate Assembly

A037784-03Strain-Relief Power Cord(United Kingdom, Ireland, Lebanon, Saudi Arabia, India, Hong Kong,

Singapore, Egypt, Nigeria, Republic of South Africa, Zimbabwe)

A038164-01Cabinet Assembly(includes glides and PCB retainers, but not the rear access panel)

A038586 Main Harness Assembly A038588-01 Power Hamess Assembly A038590-01 19-Inch Wells-Gardner Color X-Y Video Display Assembly A039990-01 Main Conversion Harness Assembly (not shown)

The following four items are the technical information supplements to this game: SP-234 Black Widow Schematic Package ST-234-01 Black Widow Label with Self-Test Procedure and Option Switch Settings TM-183, * Service Manual for 19-Inch Weils Gardner Color X-Y Display TM-234 Black Widow Operators Manual

71-2110Lock Mechanism(for rear access panel)

78-3201 Adjustable Glide 78-6900402 Viny| Foam Single-Coated Adhesive Tape, Y%4-inch Wide x %-Inch Thick 009992-01 On/Off Switch Cover 037308-01 Speaker Grille 037332-01 Ventilation Grille

037419-02Rear Access Panel(does not include lock)
038091-01Molded Coin BoxAcceptable substitute is part no. A037491-01

178013 Spring Draw Latch 178034-024 %-Inch Black Plastic T-Molding 178048-001 2nch Rigid Caster

3-3

Page 26

Inustrated Parts Lists Black Widow

WARNING Players may receive an eiectrical shock if this contro! panel is not properly grounded! After servicing any parts on the panei, check that the ground wire is firmly attached to the metal tab cn the inside of the control panel. Only then should you lock up the game. B. Control Panel

Assembly

171021-001 (Joystick)

75-5112B oa bolt)

75-9418’ (Locknut)

(Decal-—not shown)

A039975-01 (Control paneiidecal)

039973-01 (Controi panel) 'A039989-01 (Harness)

Black ‘Common, Red (+) ee Grey/whit 4 Oper ae Viclet/White

| Orange/White, Bh Black . Conan in (+) 4 Brown/White SS normaly Open White/Biack

Figure 3-2 Control Panel Assembly A039974-01 A

3-4

Page 27

Black Widow Illustrated Parts Lists

Control Panel Assembly Parts List

Part No. Description

A039975-01 Control Panel with Decal A039989-01 Contro! Panei Harness Assembly 62-039 SPDT Momentary Pushbutton Start Switch with Red Light-Emitting Diode 75-010S #10 Flat Washer 75-941S #10-24 Hexagonal Locknut 75-5112B #10-24 x ¥%-Inch Black Carriage Bolt 78-6900402 Viny! Foam Single-Coated Adhesive Tape, Y-Inch Wide x ¥%-Inch Thick 036895-01 Black Molded Switch Bezel 039973-01 Controi Panel 039976-04 Control Panel Decal 171021-001 8-Position Joystick

Page 28

Wlustrated Parts Lists Black Widow

99-080028 (Shaft)

99-080026 (Black plastic washer)

‘98-080036 (Top Plate)

99-080029 (Nylon washer)

99-080031 (Bellows)

99-080025 99-080032 (Leaf Switch) (Steel Washer)

Za 99-080037 A ~ (Switch plate) Aa < (Guard actuator)

82-AL616 (Switch actuator) (Screw) ~———— 73-3003 (Retaining Ring)

Figure 3-3 8-Position Joystick Assembly 171021-001

Page 29

Black Widow iilustrated Parts Lists

8-Position Joystick Assembly Parts List

Part No. Description 73-3003 Retaining Ring 82-AL616 #6 x 1-Inch Cross-Recessed Pan-Head Type BT Self-Tapping Stee! Screw 99-080025 Leaf Switch 99-080026 2-Inch Black Plastic Washer 99-080028 Metal Shaft 99-080029 Nylon Washer 99-080030 Spring 99-080037 Bellows 99-080032 Flat Steel Washer 99-080033 Plastic Guard/Actuator 99-080036 Top Plate 99-080037 Switch Mounting Plate 99-080038 Nylon Switch Actuator

Page 30

Illustrated Parts Lists Black Widow

C. Fluorescent Tube and Speaker

148001-017 (Speaker) 037309-01 (Top retainer) 79-561816P_ Wire nut) 038151-01 179035-001 (Lampholder) (Jumper wire) 142028-xxx (Transformer) 99-11003 (Starter) 99-11009 -A037457-01 (Socket) (Harness)

037469-01 (Bracket) 039977-01 (0375400 (Attraction glass with graphics) " 78-6900402 99-11006 (Tape) (Tab) 037304-01 To ensure that the fluorescent tube (Bottom retainer) _ starts, make sure the ground wire is firm- Z (Tube) ly attached to both the ballast transformer and the steel lamp bracket.

Figure 3-4 Fluorescent Tube and Speaker A038161-01 & -02 A Parts List

Part No. Description A037457-01 Tube and Speaker Harness Assembly A037540-01 Ground Wire with Ring Lug 70-304 18-Inch, 15-W, Cool White Fluorescent Tube 78-6900402 Vinyl Foam Single-Coated Adhesive Tape, ¥%-inch Wide x ¥, inch Thick 79-561816P Spring-Connector Wire Nut for 16- to 18-Gauge Wires 99-11003 Fluorescent Lamp Starter 99-11006 - Fluorescent Lamp Locking Tab (tab consists of two pieces) 99-11009 Starter Socket

037304-01 Bottom Attraction Glass Retainer 037309-01 Top Attraction Glass Retainer 037469-01 Steel Lamp Bracket 038151-01 16-inch Jumper Wire 039977-01 Attraction Glass with Graphics 142028-001 60 Hz, 118 V, Ballast Transformer (used on A038161-01 assembly) 142028-002 50 Hz, 118 V, Ballast Transformer (used on A038161-02 assembly) 148001-017 6 x 9-Inch, 82, 6-Ounce Oval Shielded High-Fidelity Speaker 179035-001 2-Pin Fiuorescent Lampholder

3-8

Page 31

Black Widow Illustrated Parts Lists

D. Video Displays

037322-01 (Bezel) ‘A038593-01 (Display interconnect assy.)

938181-01 (Bracket)

WARNING SHOCK HAZARD

The following procedure should only be performed by a qualified service technician. Before removing or repairing the video display, unplug the game. High voltages may exist in any video display, even with power disconnected. Use extreme caution and do not touch electrical parts of the display yoke area with your hands or with metal objects in your hands! Discharge the high voltage from the cathode-ray tube as follows: Attach one end of a large, well-insulated, 18-gauge jumper to ground. Momentarily touch the free end of the grounded jumper to the anode by sliding it under the anode cap. Wait two minutes and discharge the anode again.

IMPLOSION HAZARD \f you drop the display and the picture tube breaks, it will implode! Shattered glass can fly six feet or more from the implosion. Use care when replacing any display.

Figure 3-5 Wells-Gardner Video Display Parts List

Part No. Description

A038593-01 Wells-Gardner Interconnect Assembly 92-053 19-Inch Wells-Gardner Color X-Y CRT 038181-01 Video Display Support Bracket 037303-01 Display Shield 037322-01 Display Bezel 03733001 Display Shield Retainer Clip 038184-01 Static Shield

Page 32

Hilustrated Parts Lists Black Widow

WARNING SHOCK HAZARD

The following procedure should only be performed by a Qualified service technician. Before removing or repairing the video display, unpiug the game. High voltages may exist in any video display, even with power disconnected. Use extreme caution and do not touch electrical parts of the display yoke area with your hands or with metal objects in your hands! Discharge the high voltage from the cathode-ray tube as follows: Attach one end of a large, well-insulated, 18-gauge jumper to ground. Momentarily touch the free end of the grounded jumper to the anode by sliding it under the anode cap. Wait two minutes and discharge the anode again.

IMPLOSION HAZARD \f you drop the display and the picture tube breaks, it will implode! Shattered glass can ‘ly six feet or more from the implosion. Use care when replacing any display.

A201012-01 (High-voltage PCB)

038184-01 (Static shield)

Az01014-01 (Deflection PCB)

Figure 3-6 Amplifone Video Display

3-10

Page 33

Black Widow Illustrated Parts Lists

NOTE Ampilfone CRT (A201001-01) and Deflection PCB (A201014-01) are shipped as a matched, callbrated palr and should be used as such.

A201001-01 (Amplifone CRT)

(Shield)

Figure 3-6 Amplifone Video Display Parts List

Part No. Description (Reference Designations and Locations in Bold)

Amplitone Display Assembly A200000-01 A201001-01 19-Inch Amplifone Color X-Y CRT A201012-01 High-Voltage PCB A201014-01 Deflection PCB 034536-02 Foam Pad (used with High-Voltage and Deflection PCBs) 037303-01 Display Shield 037322-01 Dispiay Bezel 037330-01 Display Shield Retainer Clip 038184-01 Static Shield

Page 34

Illustrated Parts Lists Black Widow

E. Utility Panel Assembly eos ee. Ls N = > 002465-01 \\ (Coin counter) \ A038004-01 VA (Harness)

038003-01 (Bracket)

62-041 (Auxiliary coin switch}

19-9032 (Volume control)

76018-0025. (Screw)

88-001 178070-001 (Setfest switch) — (Yoiume control knob)

WARNING Before removing or repairing the utility panel, tum the game off. Players may receive an electrical shock if the utility panel is not properly grounded! After servicing any parts on the panel, make ‘sure that the ground wire is firmly attached to the metal screw on the back of the coin counter.

Figure 3-7 Utility Panel Assembly Parts List

Part No. Description

00246501 6 V Coin Counter A038004-01 Utility Panel Harness 19-8032 - Volume Control 62-041 SPDT Momentary-Contact Pushbutton Auxiliary Coin Switch with Black Cap 9-001 DPDT Self-Test Switch 75-916S #6-32 Standard Machine Nut 038003-01 Utility Panel 75-9910W0 *%,,-82 Stamped Nut 176018-002 #6-32 x Ve-Inch Pan Head Machine Screw 178070-001 Volume Control Knob

Page 35

Black Widow Illustrated Parts Lists

F. Coin Door Assemblies

(Lamp) LZ 179047-001 99-15023 (Lamp Base) ? (Base Plate)

99-15056 (Screw for Bezel)

99-15025 ® (Coin Inlet)

R a 99-15054 (Pivot for Lever) 99-15068 (Lockout Coil) 9945069 (Lockout Coil Spring)

99-15028 75-9148 (Coin Return Box) (Hex Nut) (Hex Nu) 75.056

(Lock Wash)

—<— 99-15060 ° Sy, (Sw. Cover) ey (Switch) | iP @ ~

7244148 (Screw)

Figure 3-8 Vertically Mounted Coin Door A037619-xxx D

3-13

Page 36

Mlustrated Parts Lists

A037542-01 (Hamess—not shown)

99-15063 (Screw)

99-15067 (Lock Assy.)

038091-01 (Coin Box)

(Door Frame)

99-15073 99-15070 (Upper Door) | (Doors and Frame) 99-15074 (Lower Door)

A037619-01 — U.S. 25¢/25¢ Coin Door A037618-02 1S. 506/50¢ Coin Door A037619-03 — Canadian 25¢/25¢ Coin Door A037618-04 — British 10 9/10 P Coin Door A037619-05 -—- British 10 PSO P Coin Door A037619-06 — British 20 P/50 P Coin Door A037619-07 — Australian 20¢e/20¢ Coin Door A037619-08 — German 1 DM/1 DM Coin Door A037619-09 — German 2 DM!1 DM Coin Door A037619-10 — German 2 DM/5 DM Coin Door A037619-11 — German 1 DM/5 DM Coin Door A037819-12 — 5 Fri5 Fr Com Door A037612-13 — Swiss 1 Fr/1 Fr Coin Door 403761914 — French 1 Fr/1 Fr Coin Door Black Widow

99-15038 (Bezel for Button)

99-15001 thru 99-5011 (Return Button)

99-15071 (Clamp)

(Bezel for Cover)

99-15066 (Screw)

03761915 — French 2 Frit Fr Coin Door A037619-46 — Swedish 1 Kr/1 Kr Coin Door AQ37619-17 — Spanish 25 Pts/25 Pts Coin Door A037619-18 — Italian 100 L/100 L Coin Door A037618-19 — Hong Kong $1/$1 Coin Door AG37619-20 — Japanese 100Y/100Y Coin Door

Figure 3-8 Vertically. Mounted Coin Door, continued A037619-xxx D

Page 37

Black Widow Illustrated Parts Lists

Vertically Mounted Coin Door Parts List

Part No. Description A037542-01 Harness Assembly 72-1414S #4-40 x_%-Inch Cross-Recessed Pan-Head Stee! Machine Screw 75-056 #6 Internal-Tooth Zinc-Plated Steel Lock Washer 75-9148 #4-40 Steel Machine Hex Nut 75-3414S #4-40 x %-Inch 82° Cross-Recessed Flat-Head Steel Machine Screw 99-15001 Coin Return Button with U.S. 25¢ Price Plate 99-15002 Coin Return Button with U.S. $1 Price Plate 99-15003 Coin Return Button with German 1 DM Price Plate 99-15004 Coin Return Button with German 2 DM Price Plate 99-15005 Coin Return Button with German 5 DM Price Plate 99-15006 Coin Return Button with Belgian 5 Fr Price Plate 99-15007 Coin Return Button with French 1 Fr Price Plate 99-15008 Coin Return Button with Japanese 100 Yen Price Plate 99-15009 Coin Return Button with British 10 Pence Price Plate 99-15010 Coin Return Button with Australian 20¢ Price Plate 99-15011 Coin Return Button with Italian 100 Lire Price Plate 99-15023 Base Plate 99-15025 Left Half of Coin Inlet 99-15026 Right Half of Coin Inlet 99-15027 Side Plate of Coin Return Box 99-15028 Base Plate of Coin Return Box 99-15029 Switch Bracket 99-15030 Flap for Lockout Coil (U.S. 25¢) 99-15036 Metal Coin Return Cover 99-15038 Bezel for Coin Return Button 99-15039 Metal Bezel for Coin Return Cover 99-15040 Coin Return Lever 99-15042 Coin Switch for U.S. 25¢ 99-15052 Spring for Coin Return Button 99-15054 Pivot for Coin Return Lever 99-15055 Retaining Screw 99-15056 #4-40 x ¥.-Inch Cross-Recessed Pan-Head Steel Machine Screw 99-15060 Switch Cover 99-15063 Screw for Hinge 99-15066 Screw for Clamp 99-15067 Lock Assembly 99-15068 Lockout Coil 99-15069 Spring for Lockout Coil 99-15070 Doors and Frame 99-15071 Clamp for Frame 99-15072 Door Frame 99-15073 Upper Door 99-15074 Lower Door 99-15075 Switch Adjuster 038091-01 Coin Box (Not included in assembly) Acceptable substitute is part number A037491-01 170000-001 6.3V Miniature Wedge-Base Incandescent Lamp 171006-035 Metal Coin Mechanism 179047-001 Lamp Base

Page 38

Itiustrated Parts Lists Black Widow

99-10140 (Panel assy.)

75-948S a (Locknut) ee i? " 99-10116 \ Hip (Lever)

99-10152 (Right coin inlet)

99-10096 (Fastener)

(Hex nut)

99-10151 (Left coin inlet)

89-10080 (Lamp oN 70-11-47 YG LH e _6| 99-10104 ; 2 (Bar retainer) Le, Screw 99-10147 (Harness)

99-10154 a

(Bracket ss

L Pi 99-1042 thru 99-1045 99-10153 i = (Coin switch assy.) (Coin return box) 7 . si te NY | aN e54atc (Coin switen} oe » 99-10150 an (Switch cover)

99-10075 thru 99-1078 ~ (Switch wire) 99-10008 7514128 (Retainer) (Screw)

Figure 39 American-Made Coin Door Assembly 171027001 A

Page 39

Black Widow illustrated Parts Lists

99-10148 (Lock)

72-HA1404C ‘Screw) 99-10142 . (Button housing)

99-10134 (Cover) 99-10139 (Coin door) ——>| 99-10119 LZ (Button assy.) ) 99.19118 4 : = (Button).

99-1015 (Spring)

99-10141 (Coin return cover) 99-10145-—> aS j (Cam) \ + i 5? 99-10117 (Coin return door)

99-10144 (Channel! clip)

i) 72-JA1405B (Screw) 99-10149 (Service door)

038097-01 (Coin box) 99-10143 (Frame)

Figure 3-9 American-Made Coin Door Assembly, continued 171027-001 A

Page 40

illustrated Parts Lists Black Widow

American-Made Coin Door Assembly Parts List

Part No. Description

171006-035 Metal Coin Mechanism for U.S. $.25 65-441 Coin Switch 70-11-47 Miniature Bayonet Lamp 72-9406S #4-40 x%-Inch Truss-Head Screw 72HA1404C #4-40 x Y-Inch Pan-Head Screw 72-3A1405B #4-40 x .31-Inch Pan-Head Screw 75-1412S #4-40 x 34-Inch Pan-Head Screw 75-9448, #4-40 Locknut 99-10008 Retainer 99-10042 Coin Switch Assembly for Belgian 5 Fr and U.S. $.25 99-10043 Coin Switch Assembly for German 1 DM, Japanese 100 Yen, Swiss 1 Fr 99-10044 Coin Switch Assembly for German 2 DM, Italian 100 L, U.S. $1.00 99-10045 Coin Switch Assembly for Australian $.20, German 5 DM, British 10 P 99-10068 Coin Return Chute 99-10075, Switch wire (included in coin switch assembly) 99-10076 Switch wire (included in coin switch assembly) 99-10077 Switch wire (included in coin switch assembly) 99-10078 Switch wire (included in coin switch assembly) 99-10080 Lamp socket 99-10081 Key holder 99-10096 Fastener 99-10104 Bar retainer 99-10105 Bar 99-10115 Spring 99-10116 Plastic Coin Return Lever 99-10117 Steel Coin Return Door 99-10118 Amber Coin Return Button 99-10119 Amber Coin Button for U.S. $.25 99-10134 Coin Button Cover 99-10139 Coin Door 99-10140 Coin Door Inner-Panel Assembly 99-10141 Diecast Coin Return Cover 99-10142 Diecast Button Housing 99-10143 Coin Door Frame 99-10144 Coin Door Channel Clip 99-10145, Offset Cam 99-10146 Coin inlet Chute Assembly 99-10147 American-Made Coin Door Harness 99-10148 Lock Assembly 99-10149 Service Door 99-10150 Switch Cover 99-10151 Left Coin Inlet 99-10152 Right Coin Iniet 99-10153 Coin Return Box 99-10154 Bracket Assembly

3-18

Page 41

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 42

Illustrated Parts Lists Black Widow

G. Power Supply Assembly

WARNING Fuse cover must be in place during game operation. A037395-01 (ianstormer Assy.)

‘A021084-xx (Volt. Plugs)

03454401 (Fuse Block Cvr.)

79-441101 (Fuse Post) 78-70501SC ; fo (Cap. i 2 d 4.201702 B : (Fuse) 0 - 034482-02 (Chassis)

78-2708 (Bushing)

A034630-01 79-3206 m (Fuse Block) (Filter Assy.)

037641-01 46-2014002 (Fuses)

. 4 A035890-01 ye ten 100 (Pwr. Harness) (Term. Biock)

A034629-01 3A-MDA3501 (AS, Harn) (Rectifier)

Figure 3-10 Color X-Y Power Supply Assembly A037396-xx D

3-20

Page 43

Black Widow Illustrated Parts Lists

Color X-Y Power Supply Assembly Parts List

Part No. Description (Reference Designations in Bold)

A021084-01Voltage Plug for 100 V(violet)
A021084-02Voitage Plug for 120 V(yellow)
A021084-04Voltage Plug for 220 V(blue)
A021084-05Voltage Plug for 240 V_(brown)

A034629-01 AC Harness Assembly

A034630-01RFI Filter Assembly(FL1)

A035890-01 Power Harness Assembly A035891-02 Fuse Harness Assembly A037395-01 Color X-Y Transformer Assembly (T1) 29-053 27,000 uF 15 VDC Electrolytic Capacitor (C1) 3A-MDA3501 Type-MDA 3501 Bridge Rectifier (CR1)

46-20140024 A, 250 V, 3AG Slow-Blow Glass Cartridge-Type Fuse(F2, F4-F6)
46-20170027 A, 250 V, 3AG Slow-Blow Glass Cartridge-Type Fuse(F1)
46-30120320 A, 32 V, 3AG Slow-Blow Glass Cartridge-Type Fuse(F3)

78-2708 Nylon Type 6/6 Hole Bushing with %-Inch Inside Diameter x *%,-Inch Outside Diameter x Y%-Inch Thick 78-70501SC 2-Inch Diameter Capacitor Mounting Bracket 79-15021001 2-Circuit Single-Row Terminal Block 79-3206 5-Position 3AG Fuse Block with ¥%-Inch Quick-Disconnect Terminals 79-441101 Panel-Mounting Non-Indicating 3AG Cartridge-Type Fuse Post 034482-02 Power Supply Chassis Base 034544-01 Fuse Block Cover 037243-01 Metal Base Plate (not shown in illustration)

037639-01Label for Fuse Value(F1)
037641-01Label for Fuse Values(F2-F6)
NOTE A037396-01 power supply assembly has the 120 V plug A037396-02 has the 100 V, 220 V, and 240 V plugs A037396-03 has the 220 V and 240 V plugs

Line Voltage Range Voltage Selection Plug Wire Color 90-110 VAC (100) 105-135 VAC (120) 200-240 VAC (220) 220-260 VAC (240) Violet Yellow Blue Brown

3-21

Page 44

illustrated Parts Lists Black Widow

H. Printed-Circuit

Boards

72-6810S (Screw) 175004-706 (Spacer) 034536-02 {Foam pad)

A040003-21, -22 (Game PCB)

A035435-04 (Regulator/ Audio $I PCB)

034536-02 (Foam pad)

Figure 3-11 PCB Mounting Hardware Parts List

Part No. Description

724810S #8 x %-Inch Phillips-Head Screw (secures PCB to cabinet) 175004-706 #8 Spacer (secures PCB to cabinet) 034536-02 Foam Pad

3-22

Page 45

Black Widow

a

oa

B (Crest

2 ec wae f ich

U zoo ome CD " ha

on-1i0%c% 1] Des

TST

bor usoreidy try. [or 210741 i] Cssiy craiky

59-1 Cast Tis

too-4 reseed (ean EG

sa (Lassi BOER tortonedy

Bal

aK? 20-0 = voc (esr

[zest Fabre a 920 1 cous 20 So

a

east 2s0-C wes e ie [exo Bam ote} Pee

“agg ae (Comme

omer] CER FI ink Be ee a i

Cas oo wane Das

eeey ff a0

(pos A a

vEIST

(ease bP

Tervs

051g

errr weet

frueredy (are 0 05

a 2 A

Figure 3-12 Black Widow Game Printed-Circuit Board Assembly {iustrated Parts Lists

‘DNIMVHG SIHL DNIAOIY SNOSH3d TIY OL SOLON

Hills gsS25588 SGT

Page 46

Illustrated Parts Lists

Black Widow Printed-Circuit Board Assembly Biack Widow

Parts List

DesignatorDescriptionPart No.

Capacitors

C1-C150.1 uF, 50 V, Ceramic-Disc Radial-Lead Capacitor122002-104
Cie47 uF, 50 V Aluminum Electrolytic Fixed Axial-Lead Capacitor24-500476
C1710 uF, 50 V Aluminum Electrolytic Fixed Axial-Lead Capacitor24-500106
C18-C220.1 uF, 50 V, Ceramic-Disc Radial-Lead Capacitor422002-104
C23100 pF, 100 V, Radial-Lead Epoxy-Dipped Mica Capacitor128002-101 .
C2439 pF, 100 V, Radiai-Lead Epoxy-Dipped Mica Capacitor128002-390
C25, C260.1 pF, 50 V, Ceramic-Disc Radial-Lead Capacitor122002-104
C27100 pF, 100 V, Radial-Lead Epoxy-Dipped Mica Capacitor128002-101
c290.1 uF, 50 V, Ceramic-Disc Radial-Lead Capacitor122002-104
C300.22 uF, 25 V, Ceramic-Disc Radial-Lead Capacitor122008-224
C31, C320.015 pF, + 10%, 100 V Radial-Lead Epoxy-Dipped Mylar Capacitor21-101153
C330.22 pF, 25 V, Cerarnic-Disc Radial-Lead Capacitor422008-224
C350.1 uF, 50 V, Ceramic-Disc Radial-Lead Capacitor122002-104
C3610 uF, 50 V Alurninum Electrolytic Fixed Axial-Lead Capacitor24-500106
C370.1 wF, 50 V Ceramic-Disc Radial-Lead Capacitor122002-104
C38, C3910 uF, 50 V Aluminum Electrolytic Fixed Axial-Lead Capacitor24-500106
C40-C430.1 uF, 50 V, Ceramic-Disc Radial-Lead Capacitor. 122002-104
C440.01 pF, 25 V, Ceramic-Disc Radial-Lead Capacitor122005-103
C45-C630.1 uF, 50 V, Ceramic-Disc Radial-Lead Capacitor122002-104
C640.1 wF, 50 V, Ceramic-Disc Radial-Lead Capacitor122002-104
C650.0018 uF, + 10%, 1 kV, Ceramic-Disc Radial-Lead Capacitor27-102182
C660.1 uF, 50 V, Ceramic-Disc Radial-Lead Capacitor122002-104
C870.1 uF, 50 V, Ceramic-Disc Radial-Lead Capacitor122002-104
Ccés0.1 uF, 50 V, Ceramic-Disc Radial-Lead Capacitor122002-104
c700.1 uF, 50 V, Ceramic-Disc Radial-Lead Capacitor122002-104
crt0.01 yF, 25 V, Ceramic-Disc Radial-Lead Capacitor122005-103

c72 0.047 uF, + 10%, 50 V, AxialLead Epoxy-Dipped Polycarbonate Capacitor 122010-473

C73-C750.1 yF, 50 V, Ceramic-Disc Radial-Lead Capacitor122002-104
C760.1 uF, 50 V, Ceramic-Disc Radial-Lead Capacitor122002-104
cr0.01 uF, + 10%, 100 V, Radial-Lead Epoxy-Dipped Capacitor21-101103
C780.1 uF, 50 V, Ceramic-Disc Radial-Lead Capacitor122002-104
c790.0018 uF, + 10%, 1 kV Radial-Lead Ceramic-Disc Capacitor27-102182

cao 0.047 yF, + 10%, 50 V, Axial-Lead Epoxy-Dipped Polycarbonate Capacitor 122010-473

C81-C840.1 uF, 50 V, Ceramic-Disc Radial-Lead Capacitor122002-104
C8510 pF, 100 V, Radial-Lead Epoxy-Dipped Mica Capacitor128002-100
C86-C1010.1 uF, 50 V, Ceramic-Disc Radial-Lead Capacitor122002-104
C103-C1090.1 uF, 50 V, Ceramic-Disc Radial-Lead Capacitor122002-104
C1102.2 uF, + 10%, 35 V Tantaium Capacitor122000-225
foahhl22 pF, 25 V Electrolytic Fixed Axial-Lead Capacitor24-250226
C11239 pF, 100 V, Radial-Lead Epoxy-Dipped Mica Capacitor428002-390
C3150 pF, 100 V, Radial-Lead Epoxy-Dipped Mica Capacitor128002-151

3-24 (Continued on next page)

Page 47

Black Widow ilustrated Parts Lists

Black Widow Game Printed-Circuit Board Assembly Parts List, continued

DesignatorDescriptionPart No.
C114-C1160.1 uF, 50 V, Ceramic-Disc Radial-Lead Capacitor122002-104
C117100 pF, 35 V Aluminum Electrolytic Fixed Axial-Lead Capacitor24-350107
C118220 pF, 100 V, Radial-Lead Epoxy-Dipped Mica Capacitor128002-221
C119, C120100 uF, 35 V Aluminum Electrolytic Fixed Axial-Lead Capacitor24-350107
C12122 uF, 25 V Electrolytic Fixed AxiatLead Capacitor24-250226
C122-C1260.1 uF, 50 V, Ceramic-Disc Radial-Lead Capacitor122002-104
C12739 pF, 100 V, Radial-Lead Epoxy-Dipped Mica Capacitor128002-390
C129100 pF, 100 V, Radial-Lead Epoxy-Dipped Mica Capacitor128002-101
C130, C1310.1 uF, 50 V, Ceramic-Disc Radial-Lead Capacitor122002-104
C13239 pF, 100 V, Radial-Lead Epoxy-Dipped Mica Capacitor128002-390
C134, C1350.1 uF, 50 V, Ceramic-Disc Radial-Lead Capacitor122002-104

Diodes

CRI, CR2Type-1N100, 100 V Switching Diode31-1N100
CR3, CR4Type-1N914, 75 V Switching Diode31-1N914
CRSType-1N100, 100 V Switching Diode31-1N100
CREType-MV5053 Light-Emitting Diode38-MV5053
CR7Type-1N100, 100 V Switching Diode31-1N100
CR8Type-1N754A, 6.8 V Zener Diode131002-001

Inductors L1-L3 100 wH, + 10%, Hot-Molded Plastic Fixed R.F. Choke (Acceptable substitute is part no. 41-3003) 141002-001

Integrated Circuits

A4Type-555 Integrated Circuit37-555
A6, A7Type-74S74 Integrated Circuit37-74S74
A8Type-74LS 194 Integrated Circuit37-74LS194
A10Type-TLO82 Integrated Circuit37-TLO82CP
A/B912-Bit Digital-to-Analog Converter137158-002
AIB11Type-MC1495L Integrated Circuit37-1495,
AIBI2Type-MC1495L Integrated Circuit37-1495
B1Type-74LS244 Integrated Circuit37-74LS244
B3Audio I/O N-Channel MOS/LS! Custom Chip01229401
BSType-LM324 Integrated Circuit37-LM324
BEType-74S86 Integrated Circuit137002-001
B7Type-74S02 Integrated Circuit37-74802
BBType-74LS 194 Integrated Circuit37-74LS194
B10Type-LF13201 Integrated Circuit37-13201
C1Type-74LS244 Integrated Circuit37-74LS244
C2Microprocessor90-6013
céType-74LS175 Integrated Circuit37-74LS175
C7Type-74LS191 Integrated Circuit37-74LS191
ceType-74LS194 Integrated Circuit37-74LS194
co10-Bit Digital-to-Analog Converter137160-003

(Continued on next page)

3-25

Page 48

Illustrated Parts Lists Black Widow

Black Widow Game Printed-Circuit Board Assembly Parts List, continued

DesignatorDescriptionPart No.
C11, C12Type-MC1495L Integrated Circuit37-1495
ciD3Audio I/O N-Channel MOS/LSI Custom ChipC012294-01
DSType-LM324 Integrated Circuit37-LM324
D6, D7Type-74LS175 Integrated Circuit37-74LS175
bg8-Bit Digital-to-Analog Converter137159-001
Di0Type-TL082 Integrated Circuit37TLO82CP
D/E11, D/E12Type-TL082 Integrated Circuit37-TLO82CP
E2Type-74LS244 Integrated Circuit37-74LS244
&3Type-74LS00 Integrated Circuit37-74LS00
£4Type-74193 Integrated Circuit37-74193
5Type-74109 Integrated Circuit37-74109
E6Type-74LS175 Integrated Circuit37-74LS175
E7Type-74S00 Integrated Circuit37-74S00
EsType-74LS273 Integrated Circuit37-74LS273
Eg10-Bit Digital-to-Analog Converter137160-003
E10Type-LF13201 Integrated Circuit37-13201
F2Type-74LS245 Integrated Circuit37-74LS245
F3Type-74S04 Integrated Circuit37-74S04
F4Type-74LS393 Integrated Circuit37-74LS393
F5Type-74LS11 Integrated Circuit137149-001
F6Type-74LS157 Integrated Circuit37-74LS157
F7Type-74LS14 Integrated Circuit37-74LS14
FBType-74L8194 Integrated Circuit37-74LS194
FQ12-Bit Digital-to-Analog Converter437158-002
H2Type-74LS244 Integrated Circuit37-74LS244
H3Type-74LS20 Integrated Circuit37-74LS20
H4Type-74LS393 Integrated Circuit37-74LS393
H5Type-74LS20 Integrated Circuit37-74LS20
H6Type-74LS175 Integrated Circuit37-74LS175
H7Type-74LS42 Integrated Circuit37-74LS42
HSType-74LS194 Integrated Circuit37-74LS194
J2Type-74LS374 integrated Circuit37-74LS374
J3Type-74LS04 Integrated Circuit37-74LS04
J4Type-74LS161 Integrated Circuit37-74LS161
J5Type-74S260 Integrated Circuit37-74S260
J6Type-74LS32 integrated Circuit37-74LS32
J7Type-74LS139 Integrated Circuit37-74LS139
J8Type-74LS194 Integrated Circuit37-74LS194
J9Vector Generator137179-001
K2Type-74LS175 Integrated Circuit37-74LS175
K3Type-74LS74 Integrated Circuit37-74LS74
K4‘Type-74S10 Integrated Circuit137236-001
KS, K6Type-74LS02 Integrated Circuit37-74LS02
K8Type-74LS157 Integrated Circuit37-74LS157

3-26 (Continued on next page)

Page 49

Black Widow

Black Widow Game Printed-Circuit Board Assembly Parts List, continued Illustrated Parts Lists

DesignatorDescriptionPart No.
kgType-74LS04 Integrated Circuit37-74LS04
K10Type-74LS175 Integrated Circuit37-74LS175
ubType-74LS00 Integrated Circuit37-74LS00
L4Type-74LS08 Integrated Circuit37-74LS08
L5Type-74LS74 Integrated Circuit37-74LS74
isType-74LS08 Integrated Circuit37-74LS08
110Type-7433 Integrated Circuit37-7433
M4Type-74LS27 Integrated Circuit37-74LS27
M3Type-74LS 164 Integrated Circuit37-74LS164
MSType-74LS32 integrated Circuit37-74LS32
M6Type-74LS161 Integrated Circuit37-74LS161
M8Type-74LS157 Integrated Circuit37-74LS157
MgType-74LS244 Integrated Circuit37-74LS244
N3Type-74LS157 Integrated Circuit37-74LS157
NSType-74LS02 Integrated Circuit37-74LS02
N6Type-74LS161 Integrated Circuit37-74LS161
N8&Type-74LS157 Integrated Circuit37-74LS157
NOType-74LS244 integrated Circuit37-74.S244
P2Type-74LS174 Integrated Circuit37-74LS174
P3Type-74LS138 Integrated Circuit137177-001
P4Type-74LS174 Integrated Circuit37-74LS174
P6Type-74LS161 Integrated Circuit37-74LS161
PBType-74LS245 integrated Circuit37-74LS245
RSType-74LS157 Integrated Circuit37-74LS 157
R4Type-74LS32 Integrated Circuit37-74LS32
R6Type-74LS161 Integrated Circuit37-74LS161
R8Type-TL082 Integrated Circuit37-TLO82CP
RQType-74LS273 Integrated Circuit37-74LS273

Miscellaneous

B48Station Single-Throw, Dual-Inline-Package Bit Switch66-118P1T
D48-Station Single-Throw, Dual-Inline-Package Bit Switch66-118P1T
P104Station Single-Throw, Dual-Inline-Package Bit Switch66-114P1T
VR1-15 V Voltage Regulator37-7915,
VR2+15 V Voltage Regulator37-7815
Y112.096 MHz, + 0.005% Crystal144000-001

Nylon Snap-In Fastener 81-4302 Test Point (Acceptabie substitute is part no. 020670-01) 179051-002

Read-Only Memories

D1Programmable Read-Only Memory136017-101
E/FAProgrammable Read-Only Memory136017-102
H1Programmable Read-Only Memory136017-103,
JProgrammable Read-Only Memory136017-104.

(Continued on next page)

3-27

Page 50

lilustrated Parts Lists Black Widow

Black Widow Game Printed-Circuit Board Assembly Parts List, continued

DesignatorDescriptionPart No.
K/LProgrammable Read-Only Memory136017-105
7Programmable Read-Only Memory136017-107
M1Programmable Read-Only Memory136017-106,
M2Electricatly-Alterable Read-Only Memory137161-001
MINTProgrammable Read-Only Memory136017-108
N4Programmable Read-Only Memory136002-125,
NIP7Programmable Read-Only Memory136017-109
RiProgrammable Read-Only Memory136010-111
R2Programmable Read-Only Memory136010-112
R7Programmabie Read-Only Memory136017-110

Random-Access Memories

«7* Random-Access Memory137211-001
NIP1Random-Access Memory137211-001

Resistors

R1-R1810 kQ, +5%, % W Resistor110000-103
R191kQ, +5%, % W Resistor110000-102
R20-R2210 kQ, +5%, % W Resistor110000-103
R231kQ, +5%, % W Resistor140000-102
R24-R4110 kQ, +5%, % W Resistor110000-103
R42220 kQ, +5%, % W Resistor110000-221
R43, R441 MQ, +5%, V4 W Resistor*110000-105
R45100 kQ, +5%, V4 W Resistor110000-104
R4622 kQ, +5%, % W Resistor110000-223
R471kQ, +5%, % W Resistor110000-102
R481 M2, +5%, % W Resistor110000-105
R493.9 kQ, +5%, % W Resistor110000-382
R50100 k2, +5%, % W Resistor110000-104
R511kQ, 5%, % W Resistor:110000-102
R523.9 kQ, +5%, 4 W Resistor110000-392
R53, R543.3 kQ, +5%, % W Resistor110000-332
R551kQ, +5%, % W Resistor110000-102
R56.4.7 kQ, +5%, V4 W Resistor410000472
R572.2 kQ, +5%. VY W Resistor110000-222
R58.10 kQ, +5%, % W Resistor110000-103
R591.2 kQ, +5%, % W Resistor110000-122
REO3.9 kQ, 5%, Vv W Resistor110000-392
R61-R6810 kQ, +5%, % W Resistor410000-103
R6922 k2, +5%, % W Resistor110000-223
R7068 kQ, +5%, V4 W Resistor110000683
R711kQ, +5%, % W Resistor110000-102
R7210 kQ, +5%, 4 W Resistor110000-103
R73220 kQ, +5%, ¥4 W Resistor110000-221

(Continued on next page)

3-28

Page 51

Black Widow Illustrated Parts Lists

Black Widow Game Printed-Circuit Board Assembly Parts List, continued

DesignatorDescriptionPart No.
R74-R81100 kQ, +5%, % W Resistor110000-104
R821kQ, +5%, ¥% W Resistor110000-102
R83680 2, +5%, ¥% W Resistor110000-681
Re4820 , +5%, % W Resistor110000-821
R8610 kQ, +5%, %4 W Resistor110000-103
R87, R887.5 kQ, +1%, % W Resistor110003-752,
R893.9 kQ, +5%, Vs W Resistor110000-392
R90, R91100 2, +5%, Ye W Resistor110000-101
R92, R9310 kQ, +5%, Ys W Resistor110000-103
Ro4, ROS820 Q, +5%, % W Resistor110000-821
R96, R977.5 kQ, +1%, % W Resistor110003-752

R98, ROD 500 Q Vertical PCB-Mounting Cermet Trimpot (Acceptable substitute is part no. 19-315501) 119002-501

R100, R1017.5 kQ, +1%, % W Resistor110003-752
R102, R103220 kQ, +5%, % W Resistor110000-221
R104-R1061kQ, +5%, v4 W Resistor110000-102
R107150 2, +5%, % W Resistor110000-151
R108-R1131kQ, +5%, % W Resistor140000-102
R114-R119470 Q, +5%, Vs W Resistor110000-471
R121-R1271kQ, +5%, ¥% W Resistor110000-102
R128-R131470 Q, +5%, Vs W Resistor110000-471
R133-R135470 Q, 5%, % W Resistor110000-471
Ri36-R13810 kQ, +5%, % W Resistor110000-103
R139-R1431kQ, +5%, % W Resistor110000-102
R144-R148470 Q, +5%, % W Resistor110000-474
R1491kQ, 5%, % W Resistor110000-102
R15015 kQ, +5%, % W Resistor110000-153
R151470 2, +5%, % W Resistor110000-471
R15368 Q, +5%, % W Resistor110001-680
R1521kQ, +5%, Vs W Resistor110000-102
R154470 Q, +5%, Vs W Resistor110000-471
R15522 kQ, +5%, % W Resistor110000-223
R1561kQ, +5%, % W Resistor110000-102
R158470 2, +5%, Vs W Resistor110000-471
R15910 kQ, +5%, % W Resistor110000-103
R1601kQ, +5%, % W Resistor110000-102
R16115 kQ, +5%, v4 W Resistor110000-153
R162, R1637.5 kQ, + 1%, % W Resistor110003-752
R164560 2, +5%, % W Resistor110000-561
R165-R1687.5 kQ, +1%, % W Resistor110003-752
R169, R170470 Q, 5%, % W Resistor110000-471
R173-R1752.2 kQ, +5%. Vs W Resistor110000-222
R176470.2, +5%, ¥% W Resistor110000-471
R17715 kQ, +5%, Ys W Resistor410000-153
R1783.9 kQ, +5%, % W Resistor110000-392

(Continued on next page)

Page 52

Illustrated Parts Lists Black Widow

Black Widow Game Printed-Circuit Board Assembly Parts List, continued

DesignatorDescriptionPart No.
R17910 kQ, +5%, % W Resistor110000-103
R180680 Q2, +5%, % W Resistor110000-681
R1812.7 kQ, +5%, Vs W Resistor410000-272
R1821kQ, +5%, Y% W Resistor110000-102
R1833.9 kQ, + 5%, % W Resistor410000-392
R184470 Q, 5%, % W Resistor110000-471
R1852.2 kQ, +5%. Vs W Resistor110000-222
R1863.9 kQ, +5%, %4 W Resistor410000-392

R187 2 kQ Vertical PCB-Mounting Cermet Trimpot (Acceptable substitute is part no. 19-315202) 119002-202

R18856 kQ, +5%, V4 W Resistor110000-562

R189 10 kQ Vertical PCB-Mounting Cermet Trimpot (Acceptable substitute is part no. 19-315103) 119002-103

R1901.2 kQ, +5%, % W Resistor110000-122

R192 10 kQ Vertical PCB-Mounting Cermet Trimpot (Acceptable substitute is Part no. 19-315103) 119002-103

R193, R194470 Q2, +5%, % W Resistor110000-471
R195270 2, +5%, Ys W Resistor190001-271
R196-R1982.2 kQ, +5%. % W Resistor110000-222
R199470 2, +5%, % W Resistor110000-471
R20012 kQ, +5%, V4 W Resistor110000-123
R2013.9 kQ, +5%, % W Resistor110000-392
R20210 kQ, +5%, va W Resistor110000-103
R203680 2, +5%, %4 W Resistor110000-681
R2041kQ, +5%, % W Resistor110000-102
R2052.7 kQ, +5%, V4 W Resistor110000-272
R2063.9 kQ, +5%, % W Resistor110000-392
R2072.2 kQ, +5%. V4 W Resistor410000-222
R2083.9 kQ, + 5%, % W Resistor110000-392,
R209470 2, 5%, va W Resistor110000-471

R210 2 kQ Vertical PCB-Mounting Cermet Trimpot (Acceptable substitute is part no, 19-315202) 119002-202

R2115.6 kQ, +5%, % W Resistor110000-562

R212, R213 10 k@ Vertical PCB-Mounting Cermet Trimpot (Acceptable substitute is part no, 19-315103) 119002-103

R214100 2, +5%, %4 W Resistor110000-101
R21568 O, +5%, % W Resistor110000-680
R2166.8 kQ, +5%, v4 W Resistor110000-682
R217100 2, +5%, % W Resistor110000-101
R21868 2, +5%, ¥4 W Resistor110000-680
R2196.8 kQ, +5%, % W Resistor110000-682
RV1, RV2Voitage Dependent Resistor110004-001

(Continued on next page}

Page 53

Black Widow Wustrated Parts Lists

Black Widow Game Printed-Circuit Board Assembly Parts List, continued

DesignatorDescriptionPart No.

Sockets

B340-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C40
c240-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C40
C/D340-Contact Medium-insertion-Force integrated Circuit Socket79-42C40
D124-Contact Medium-insertion-Force Integrated Circuit Socket79-42C24
E/F124-Contact Medium-Iinsertion-Force Integrated Circuit Socket79-42024
H124-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C24
J24-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C24
Jo40-Contact Medium-insertion-Force Integrated Circuit Socket79-42C40
K724-Contact Medium-insertion-Force Integrated Circuit Socket79-42C24
KILI24-Contact Medium-insertion-Force Integrated Circuit Socket79-42C24
724-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C24
M124-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C24
M222-Contact Medium-insertion-Force Integrated Circuit Socket79-42C22
MIN724-Contact Medium-insertion-Force Integrated Circuit Socket79-42C24
N/P124-Contact Medium-insertion-Force Integrated Circuit Socket79-42C24
N/P724-Contact Medium-Iinsertion-Force Integrated Circuit Socket79-42024
R724-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C24

Transistors

QiType-2N3904, 60 V, 1 W NPN Transistor34-2N3904

Q2-04 Type-2N6044 Darlington NPN Transistor 34-2N6044

Q5, Q6Type-2N3904, 60 V, 1 W NPN Transistor34-2N3904
Q7Type-2N3906 PCB Switching and Amplifying Transistor33-2N3906
Q8Type-2N3904, 60 V, 1 W NPN Transistor34-2N3904
Q10Type-2N3904, 60 V, 1 W NPN Transistor34-2N3904
QnType-2N3906 PCB Switching and Amplifying Transistor33-2N3906
Qi2Type-2N3904, 60 V, 1 W NPN Transistor34-2N3904

3-31

Page 54

Hlustrated Parts Lists

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyvale, CA, This drawing is only conditionally issued, and neither receipt nor Dossession thereof confers or transfers any right in. oF li Zense to use. the subject matter of the drawing or any design or technical information shown thereon, nor any right

to reproguce this drawing or any part inereol. Except for

manutgcture by vendors of Atari, and for manutacture under the corporation's written license, no night to repro. duce this drawing is granted or the subject matter thereot unless by written agreement with or written permission from the corporation. Biack Widow

RS = fom] c20_ Cal 0 crs = 3300 35V

C18 = 3300 +/>— 35V q

G > am ©

TIP 32, TOAZ0024 TDAZO02A

Figure 3-13 Regulator/Audio Il PCB Assembly

3-32 A035435-04 D

Page 55

Biack Widow

Regulator/ Audio || PCB Assembly Illustrated Parts Lists

Parts List

DesignatorDescriptionPart No.

Capacitors

C1470 uF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor(24-250477
C20.001 uF, 50 V, Ceramic-Disc Axial-Lead Capacitor.122002-102
c30.1 uF, +80%, -20%, 50 V, Ceramic-Disc Capacitor122001-104
C4470 uF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-250477
cs0.01 uF, 25 V Minimum, Ceramic-Disc Axial-Lead Capacitor (Accep-100015-103

table substitute is part no. 122005-103)

cé0.22 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor122004-224
Cc?0.001 uF, 50 V, Ceramic-Disc Axial-Lead Capacitor122002-102.
c80.22 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor122004-224
C9, C103300 uF, 35 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-350338
cit0.1 uF, +80%, -20%, 50 V, Ceramic-Disc Capacitor122001-104.
C12470 uF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-250477
C131000 uF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-250108
C140.01 uF, 25 V Minimum, Ceramic-Disc Axial-Lead Capacitor100015-103

(Acceptable substitute is part no. 122005-103)

C150.22 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor122004-224
C160.001 uF, 50 V, Ceramic-Disc Axial-Lead Capacitor122002-102
Ci70.22 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor122004-224
C18, C193300 uF, 35 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-350338
C20, C210.1 uF, + 80%, -20%, 50 V, Ceramic-Disc Capacitor122001-104

Diodes

CRIType-1N4002, 1 A, 100 V Silicon Rectifier Diode31-1N4002
CR4Type-1N4002, 1 A, 100 V Silicon Rectifier Diode31-1N4002
CR5-CR8Type-1N5401, 3 A, 100 V Silicon Rectifier Diode31-1N5401

Integrated Circuits

QiType-LM305, 5 V, Linear Voltage Regulator37-LM305
QsType-TDA2002A, 8 W, Linear Audio Amplifier Integrated Circuit137151-002
Q7Type-TDA2002A, 8 W, Linear Audio Amplifier Integrated Circuit137151-002

Resistors

R1270 Q, +5%, % W Resistor110000-271
R333 2, +5%, % W Resistor110000-330
R4100 2, +5%, % W Resistor110000-101
RS2.7 2, +5%, 1 W Resistor110009-027
R63.9 kQ, +5%, % W Resistor110000-392
R77.5 kQ, 5%, % W Resistor110000-752
R81k@ Vertical PCB-Mounting Cermet Potentiometer(Acceptable19-315102

substitute is part no. 119002-102)

RO220 Q, 5%, v2 W Resistor110001-221

(Continued on next page)

3-33

Page 56

illustrated Parts Lists

Regulator/Audio || PCB Assembly Parts List, continued Biack Widow

DesignatorDescriptionPart No.
R1012, +5%, V% W Resistor110000-010
R1110 2, 5%, % W Resistor110000-100
R12100 2, + 5%, % W Resistor110000-101
R13, R1410 kQ, + 5%, % W Resistor110000-103
R1912, +5%, Vs W Resistor110000-010
R2010 2, +5%, % W Resistor140000-100
R21220 2, +5%, v2 W Resistor110001-221
R22100 2, +5%, %4 W Resistor110000-101
R240.1 2, 3%, 7 W Wirewound Resistor19-100P 1015
R27, R281k2, +5%, % W Resistor110000-102
R29, R3010 2, +5%, % W Resistor110000-100
R32, R335.6 kQ, +5%, %4 W Resistor110000-562

Transistors

Q2Type-TIP32 PNP Power Transistor33-TIP32
Q3Type-2N3055 NPN Silicon Transistor34-2N3055

Mechanicai Parts

J66-Position Connector Receptacle79-58306
J79-Position Connector Receptacle79-58308
J84Position Connector Receptacle79-58354
Jo6Position Connector Receptacle7958306
J1012-Position Connector Receptacle79-58346
Q2#6-32 x Y4-Inch Binder-Head Nylon Screw75-F60405
Q3#6-32 Nut/Washer Assembly75-99516
Q3Thermally Conductive Silicon Insulator78-16008
Q2Thermally Conductive Silicon Insulator78-16014
Q5, Q7#6 x %Inch Cross-Recessed Pan-Head Thread-Forming Type-AB Zinc-72-6606S

Plated-Steel Screw

Heat Sink 034531-01 Test Point (Acceptable substitute is part no. 020670-01) 179051-001

Page 57

YOUR COMMENTS, PLEASE!

Your comments will assist Atari in improving our publications. The comments are an important part of preparing for revisions of game manuals. Please write in the space below. No postage stamp is necessary if mailed in the U.S.A.

If you have any technical questions about certain ATARI games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.

Page: Comments:

Fill in if you wish a reply: .

Name.

Firm D Distributor

Address C Operator City State Zip O Other. Biack Widow 1st printing

Area Code Phone

Page 58

First told

No Postage Necessary if mailed in the United States

Le

BUSINESS REPLY MAIL =

FIRST CLASS PERMIT NO. 1004 SUNNYVALE, CA ee POSTAGE WILL BE PAID BY ADDRESSE& =_—e

  • Atari, Inc. a Attn.: Field Service/Coin-Op Division P. 0. Box 427 epeemnemenmee! Sunnyvale, California 94086 Pe a a

Second told ==OSOSC*~<“<*‘“*‘“‘*~*S*~‘“‘“‘“S*S*S*SSSSS

WOs4 aBpa syyy ede,

Page 59

perce prariarit ig oy) seco aac ti mir eacec ie

workmanship under normal use and service for a period of ninety :

ment. None of the Seller’s other products or parts thereof are warranted. Ifthe electronic parts supplied in this kit fail to conform to this warranty, Seller’s sole liability shall be, at its option, to repair, replace, or credit Buyer’s account for such electronic parts which are returned to Seller during said warranty period, provided:

  • Seller is promptly notified in writing upon discovery by Buyer that said products are defective;
  • Such products are returned prepaid to Seller’s plant; and

assumes nor tion with the sale of products by Seller.

The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to youand others. Be very cautious in using non-Atari-supplied components with our games, in order to ensure your safety. Atari distributors are: being privately owned and operated. In their judgment they Ree iiny aNauUR For ReTy CCiEVncanedl including eat

is performed by such distributor. oe

Page 60

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.