CATHODE RAY TOMES

Rush'N Attack Conversion Kit Instruction Manual

Rush'n Attack (PlayChoice-10) (Konami (Nintendo of America license), 1987) · Instruction Manual · 13 pages · 28 sections · original scan

Page 1

% RUSH ’N ATTACK™ CONVERSION KIT x

INSTRUCTION MUAINCAL , PG ma

jonami.

e istered Konami Inc. trademark ot Konami indostty Sou Utd,

1555 BRUMMEL AVENUE, ELK GROVE VILLAGE, IL 60007 ed is a registered

TELEPHONE: (312) 364-6633 FAX: (312) 364-1368 TELEX: 6871385 KONAM UW trademark of Konami Inc. © 1985 Konami Inc.

Page 2

Konami Inc. Konamis

Ben Har-El President

Dear Operator:

There are 1.5 Million CHILDREN REPORTED MISSING each year in America. Some of these children are players in our Arcades.

We at Konami feel that it is our responsibility to participate in combating this Real and Growing problem. Won't You Help Us Find The Children?

Konami is working in cooperation with CHILD FIND, IN., a not-for-profit corporation organized to aid parents, legal authorities and the F.B.I. in the finding of missing children. In an effort to do so, we have attached to our kits and video games, a poster and a decal showing photos of children that are listed with Child Find as missing.

Because of the tremendous exposure your gameroom or location can provide, we ask that you PROMINENTLY DISPLAY the posters and place the decals on each of the Konami games. We, and the parents of these children are very greatful for any help that you give us in assisting this extremely important program.

If it is possible for you to assist Child Find further by sending a tax deductible donation or if you would like to volunteer any time or services, please contact Child Find at:

CHILD FIND, IN. P. O. BOX 277 New Paltz, NY 12561 Phone: (914) 255-1848

Again, thank you very much for helping us to help find the children. We deeply appreciate your concern and cooperation.

Best regards,

KONAMI INC.

Ben Har-El President

PLEASE DON'T FORGET TO DISPLAY THE POSTERS AND DECALS!

1555 BRUMMEL ELK GROVE VILLAGE, ILLINOIS 60007 PHONE: (312) 364-6633 TELEX: 6871385 KONAM UW FAX: (312) 364-1368

Page 3

TABLE OF CONTENTS

Page Page

Conversion Kit Contents ...............4- 1 Monitor Info... 0... 6. ee eee 5

Table of Contents. .......... 0... e ee eee eee 1 Wiring Harness Color Code.............-5 6

Introduction... 0.0.6... eee eee eee eee 2 Wiring Diagram ... 2.6.6.0 6.6. e cece eee 7

Recommended Control Panel Layouts...... 2 Technical Information ..............+-04. 8

Graphics... 0... cece eee 3 Dip Switch Setting. ............ 0... ee eee 9

Monitor Specifications ................05 4 User Information Warning........ Back Cover

CONVERSION KIT CONTENTS:

¢ MAIN PRINTED CIRCUIT BOARD ¢ P.C.B. CAGE (FCC REQUIRED) ¢ CONNECTING WIRING HARNESS ¢ 6 SETS — BUTTON ASSEMBLIES © 8-WAY JOYSTICK ¢ MARQUEE (HEADER) (1/8” acrylic sheet) ¢ ONE SET SIDE PANEL GRAPHICS (left & right) ¢ CONTROL PANEL OVERLAY ¢ CONTROL PANEL DECALS instruction decals/button decals (2 sets) e¢ FCC WARNING LABEL ¢ MANUAL ¢ REGISTRATION CARD

REPLACEMENT ACCESSORIES ARE AVAILABLE THROUGH YOUR DISTRIBUTOR.

THIS KIT USABLE FOR COCKTAIL AND UPRIGHT VIDEO GAMES WITH A RASTAR SCAN MONITOR WHICH IS OR CAN BE MOUNTED HORIZONTALLY.

Page 4

RUSH ’N ATTACK INTRODUCTION

a

KONAMI CONVERSION KITS are the most complete conversion kits available today. Every detail has been carefully considered, designed and packaged to provide you the means of easily producing a professional conversion.

These kits have all the accessories to easily convert your UPRIGHT or COCKTAIL video game.

We strongly urge you to FULLY STUDY this instruction manual BEFORE you begin your conversion. It contains step-by-step instructions, schematic diagrams and suggestions on how to install your Konami Conversion Kit and maximize your profits. RUSH 'N ATTACK can be installed in any horizontally mounted rastar scan monitor game.

Everything you will need to construct your new game is Provided in this kit. All accessory parts — wiring harness, joystick, etc. are custom made for RUSH 'N AT- TACK by top engineers experienced in the coin-op industry. An 8-way joystick (as provided) MUST be used.

The Player Instruction and Button Control decals are made of a non-destructible acrylic material specifically to keep the player from peeling them off. Should you convert a cocktail table game, RUSH 'N ATTACK is sup- Plied with 2 sets of button decals.

SAVE YOURSELF TIME AND MONEY

The following P.C.B.’s are interchangeable with RUSH 'N ATTACK P.C.B.’s Super Cobra ¢ Scramble * Pooyan * Locomotion ¢ Circus Charlie * L'i! Hustler Juno First * Time Pilot * Gyruss * Tutankham © Turtles * Super Basketball «© Mega Zone Pandora's Palace * Time Pilot '84 © Track ‘n’ Field * Hypersports * Roadfighter * Yie-Ar Kung Fu * Kicker Mikie * Frogger (60% — check pin print-out) * Amidar * Roc’N Rope * The End {n other words, your RUSH ’N ATTACK will plug right into existing edge connectors of the games listed above — be sure to check your pin print-out. (Keep in mind that Rush 'N Attack is designed as a horizontal game.)

DUAL CONTROL

By moving SW#2 of dip switch bank #3 to the “on” position, you are now in the dual control upright mode. This allows you to set up an upright game with two sets of controls rather than one set. The first set of controls should be hooked up to the 1P set of wires; the second set to the 2P wires (see wiring diagrams). Each player stili challenges the “computer-controlled” opponent (alternating play). This does not allow simultaneous interaction of players on the video screen.

SINGLE CONTROL LAYOUT DUAL CONTROL LAYOUT

Bia ta ee > ee . S64 22 ae SHOOT KNIFE 2 KNIFE SHOOT cae) KNIFE ne ois KNIFE SHOOT

Page 5

PUTTING YOUR BEST GAME FORWARD

PREPARATION: For best results, all old graphics should be removed completely from the cabinet. “Stick-on” graphics can be temoved by using a hairdryer or hot air device. The heat from the dryer will loosen the adhesive, allowing you to easily peel them off — any adhesive residue can be cleaned off with acetone and a soft dry cloth. (DO NOT USE ACETONE ON SURFACES PAINTED WITH FLAT PAINT.) TOOLS YOU NEED:

  • Foaming Aerosol (such as ‘‘Windex").
  • Soft Squeegee. =
  • X-Acto Knife.

SIDE PANEL DECALS

  • Spray area of cabinet where Side Panel decals are to be applied with foaming aerosol or a mild soap solution. . Remove protective backing from decals. . Position decals into place. . With a soft squeegee, beginning from the center of the decal, slowly and evenly press out excess foam until you achieve a smooth finish.
  • Allow to set approximately 2 to 3 hours before handlirg. Maximum adherence is achieved in 48 to 72 hours. PON
  • Trim side decal to fit your cabinet.

Sd ete PANEL OVERLAY: . Refer to Recommended Contro! Panel Layout on page 2. . Drill any new holes needed, . Plug any holes that will not be used. (A permanent epoxy filler works well for this step.) . Pre-position the overlay prior to removing the backing. . Slowly apply the overlay — inch by inch on the control panel, removing the backing as you apply it.

  • Once it's in place, by using an X-Acto knife, cut around the button and joystick placements. INSTRUCTION/BUTTON DECALS: Apply the Player Instruction, Button and 1 Player/ 2 Player decals in their respective positions. Apply Pressure liberally, Allow to set as long as possible before putting game on location. oO FF ON
NOTE: Maximum adherence is achieved in 48 to 72 hours.

FCC WARNING LABEL: FCC Warning Label must be applied to the outside of the cabinet near the line cord entry.

MARQUEE

(WEAR PROTECTIVE GLASSES WHILE TRIMMING MARQUEE)

1/8” Acrylic Marquee should be cut to fit your game. DO NOT remove protective mask until this is done. One way of cutting your Marquee is as foilows: (Be sure to protect painted side of Marquee from any surface which may scratch or mar finish). CUTTING WITH A KNIFE OR SCRIBER Acrylic sheet up to 3/16” thick may be cut by a method similar to that used for cutting window glass. Use a scriber of some kind — a scribing knife such as the one pictured, a metal scriber, an awl, or even a sturdy craft knife — to score the sheet. Draw the scriber several times (7 or 8 times for a 3/16” thick piece) along a straight edge held firmly in place. It is best not to remove the protective masking. Make the cuts carefully using firm, even pressure. For best results make each stroke cleanly off the edge of the sheet. Then clamp the acrylic sheet or hold it rigidly under a straight edge with the scribe mark hanging just over the edge of a table. Protect your hands with a cloth, and apply a sharp downward pressure to the other side of the sheet. It will break along the scratch. Scrape the edges to smooth any sharp corners. This method is not recommended for long breaks or thick material.

Break sheet over edge of table after scribing Always draw the scribing knife along a straight edge.

P.C.B. CAGE INSTALLATION

Konami, Inc. now supplies a new style P.C.B. cage which is superior to old style cages because of ease of installation. The cage is made of a 32 point stem-stock which is fire retardant. TO INSTALL THE CAGE:

  • Open cage bottom and secure to desired P.C.B. position.
  • Install printed circuit board inside cage using wood screws, screwed through the cage bottom into cabinet side.
  • Close the cage over printed circuit board and secure with latch on cage.
Page 6

RUSH ’N ATTACK: MONITOR SPECIFICATIONS

Rush 'N Attack requires a horizontally mounted monitor. It also generates composite negative sync. If your monitor is composite positive sync, you will have to change to composite negative sync.

  • To alternate composite positive sync to composite negative sync, use 7404 IC or 74LS04 IC. The signal on the output pin from the P.C.B. is a combination of H-sync and V-sync.
NOTE: Please refer to Figure 2.

FIGURE 2: +5V

FROM P.C. BOARD

NEGATIVE COMPOSITE SYNC. (PIN 14 on P.C.B EDGE) OUTPUT TO MONITOR POSITIVE COMPOSITE SYNC.

_ (+ &V and GND should be taken out of the P.C. Board.)

  • Separate Sync modification for Rush ’N Attack if your monitor has “Separate Sync” input. (For example “Electrohome brand” and Wells-Gardner brand.”) Step 1 WIRING HARNESS

VIDEO SYNC

If the picture is still not stable... Step 2 Prepare Hook-up wire. (For example “Electrohome brand.”)

WIRING HARNESS

VIDEO SYNC

Page 7

RUSH ’N ATTACK: MONITOR INFO.

SERVICE INSTRUCTIONS

NOTE: All monitors are equipped with automatic degaussing coils (L701) which demagnetize the picture tube every time the monitor is turned on after being off for a minimum of 5 minutes. Should any part of the chassis become magnetized it will be necessary to degauss the affected area with a manual degaussing coil. Move the coil slowly around the CRT face and all surrounding metal parts. Then slowly withdraw for a distance of 6 feet before turning off.

1.0 BLACK LEVEL CONTROL ADJUSTMENT This control has been set at the factory and should not need further attention, however, when the game is connected a slight adjustment of VR201 may be necessary to obtain the proper black level (the black portion of the picture just extinguished).

2.0 VERTICAL SIZE (HEIGHT) Location of this control is shown in Fig. 1. This control must be adjusted slowly, if necessary, until the picture or test pattern attains the correct vertical proportions.

3.0 CIRCUIT PROTECTION A 4.04 pigtail fuse, mounted on the Main Board has been provided to protect the Power Output Circuit.

4.0 FOCUS Adjust the focus control, located on the HV unit (T352), for maximum over-all defination and fine picture detail.

5.0 HORIZONTAL HOLD CONTROL ADJUSTMENT, VR351 (See Fig. 1) A warm-up period of at least five minutes should be allowed before alignment is carried out. With the monitor being driven from the game signal, short TP601 to TP31. Adjust VR351 until the picture stops sliding horizontally. Remove the short.

HORIZONTAL VIDEO POSITION If the video is off center on the raster some compensation can be made by adjusting this control.

7.0 VERTICAL RASTER POSITION ADJUSTMENT If the video is off center vertically, (short dimension of picture tube) some compensation can be made by moving the vertical raster position adjustment jumper to either positions “U” or “D”.

8.0 HORIZONTAL RASTER POSITION ADJUSTMENT If the video is off center horizontally (long dimension of the picture tube) some compensation can be made by moving the horizontal raster position adjustment jumper to either positions “R” or “L”. 6.0 9.0 HORIZONTAL WIDTH ADJUSTMENT The horizontal width coil is a hexagonal tuning tool adjustment. This control must be adjusted slowly, if necessary, until the picture or test pattern attains the correct horizontal proportions.

  • KONAMI GAMES ARE ALL NEGATIVE COMPOSIT SYNC. USE THE THREE PIN CONNECTOR ON THE MONITOR.

GRN o prive— '9 —_REO ORIVE REO CUTOFF GRN CUTOFF’. BLU CUTOFF

*NEG H SYNC NOTE:

WHEN USING COMPOS: +GND. ITE SYNC USE HORIZ. SYNC INPUTS, POS H SYNC POS V SYNC, word GND coi BLU GaN HORIZ HOLD

RED BLK LEVEL

HORIZ VERT VERT VERT HORIZ CENTERING SIZE HOLD RASTER RASTER SHIFT SHIFT

FIGURE 1

Page 8

RUSH ’N ATTACK: WIRING HARNESS

WIRE COLOR KEY: (Solder Side) (Parts Side)

(EMPTY)

RED/GREEN SPEAKER OUT A |B | SPEAKER OUT ORANGE/GREEN

RED/YELLOW *2P KNIFE ~—C—| |e E 2P SHOOT* ORANGE/YELLOW BROWNIYELLOW * 2P LEFT |_~4—] 2P RIGHT* BLUEIYELLOW VIOLETIWHITE 1P START 5 | 2PSTART VIOLETYELLOW ORANGEMHITE = 4P SHOOT [~F-}-6~ | 2PUP* BLACK/YELLOW REDWHITE — 1P KNIFE | H_ |-2—+SERVICESW ORANGE/GRAY BLUE/WHITE -- 1PRIGHT| J | 8 | 1PLEFT “~ BROWNMHITE BLACK/WHITE 1P UP | *~| “8 | 2P DOWN* GRAY/YELLOW REDIGRAY coiIn1 | L | 10 | CoIN2 BLUE/GRAY GRAYMHITE 1P DOWN | M_| 11 | COINCOUNTER 1 GREEN/GRAY

N P R s T U

as + 12V DC ORANGE

| 3] WHITE/PINK (NOT USED) 12 | COINCOUNTER2 YELLOWIGRAY GREEN/BROWN VIDEO GREEN 13 | VIDEO BLUE BLUE/BROWN RED/BROWN VIDEO RED 14 | VIDEOSYNC WHITE/BROWN (EMPTY) 15. | (NOTUSED) YELLOWIPINK BLACK GND 16 | GND BLACK BLACK GND 17 | GND BLACK —RED- + svc | “|. | + svDC RED

(BASE COLORILINE COLOR)

“Cocktail Table or Dual Control Upright Only

Page 9

N

RUSH ’N ATTACK

WIRING DIAGRAM

HXNOT APPLICAALE 2 2A CAPACITY.

Mnl2W 4 012W, bnbW BaéW er

PL t

PARTS SIDE

pe SIDE

+12V

SPEAKER OUT

2P SHOOT

same as /P CONTROLS only for TABLE TYPE 2P KNIFE

2P SHOOT *

2P RIGHT. wl alele 2P LEFT. 2P KNIFE * 2P RIGHT * *

22 START 1P START 2P LEST 2P START

2P_uP Bz)

CONTROLS for 2P IP START 2p UP

SERVICE SWITCH ao) 1P SHOOT SERVICE 1P KNIFE IP LEFT

2P GAME START i i 2P DOWN *¥3 L

IP GAME START aa KI SHOOT KNIFE 1P SHOOT on IP RIGHT 2P DOWN *

IP UP COIN 2 COIN ! COIN COUNTER 1

RIGHT IP DOWN COIN COUNTER 2 BLUE

LEFT 1P KNIFE COM 2.

iP LEFT

uP 1P RIGHT.

Down Q iP UP

CONTROLS

  • NOTES — (DIP NO. player 2P NO.2 player surge killer diodes for COIN

COUNTER *Cocktail Table or Dual Control

Upright Only instolled on the P.C.8 2 DOWN color MONITOR ED — GREEN SYNC RED GND GND

+12¥ POWER eye.y OND +5V (5A) ~ED6E CONNECTOR INCH PITCH

5732

Page 10

RUSH ’N ATTACK: MONITOR INFO.

SERVICE INSTRUCTIONS

NOTE: All monitors are equipped with automatic degaussing coils (L701) which demagnetize the picture tube every time the monitor is turned on after being off fora minimum of 5 minutes. Should any part of the chassis become magnetized it will be necessary to degauss the affected area with a manual degaussing coil. Move the coil slowly around the CRT face and all surrounding metal parts. Then slowly withdraw for a distance of 6 feet before turning off.

1.0 BLACK LEVEL CONTROL ADJUSTMENT This contro! has been set at the factory and should not need further attention, however, when the game is connected a slight adjustment of VR201 may be necessary to obtain the proper black level (the black portion of the picture just extinguished).

2.0 VERTICAL SIZE (HEIGHT) Location of this control is shown in Fig. 1. This control must be adjusted slowly, if necessary, until the picture or test pattern attains the correct vertical proportions.

3.0 CIRCUIT PROTECTION A 4.0A pigtail fuse, mounted on the Main Board has been provided to protect the Power Output Circuit.

4.0 FOCUS Adjust the focus control, located on the HV unit (T352), for maximum over-all defination and fine picture detail.

5.0 HORIZONTAL HOLD CONTROL ADJUSTMENT, VR351 (See Fig. 1) A warm-up period of at least five minutes should be allowed before alignment is carried out. With the monitor 9.0 HORIZONTAL WIDTH ADJUSTMENT The horizontal width coil is a hexagonal tuning tool adjustment. This control must be adjusted slowly, if necessary, until the picture or test pattern attains the correct horizontal proportions.

  • KONAMI GAMES ARE ALL NEGATIVE COMPOSIT SYNC. USE THE THREE PIN CONNECTOR ON THE MONITOR.

REO CUTOFF GRN CUTOFF BLU CUTOFF

*NEG H SYNC *NEG V SYNC *GND

NOTE: WHEN USING COMPOS-| ITE SYNC USE HORIZ. SYNC INPUTS, POS H SYNC being driven from the game signal, short TP601 to TP31. Adjust VR351 until the picture stops sliding horizontally. Remove the short.

6.0 HORIZONTAL VIDEO POSITION If the video is off center on the raster some compensation can be made by adjusting this control.

7.0 VERTICAL RASTER POSITION ADJUSTMENT If the video is off center vertically, (short dimension of picture tube) some compensation can be made by moving the vertical raster position adjustment jumper to either positions “U" or “D".

8.0 HORIZONTAL RASTER POSITION ADJUSTMENT if the video is off center horizontally (long dimension of the picture tube) some compensation can be made by moving the horizontal raster position adjustment jumper POS V SYNC.

HORIZ HOLO

BLK LEVEL

to either positions “R” or “L” pies te neeh meter Ricres er positions CENTERING SIZE HOLO RASTER RASTER

SHIFT SHIFT

FIGURE 1 i ®

Fé SE se S< . 88 oD

N

Page 11

RUSH ’N ATTACK: TECHNICAL INFORMATION

  • Required Power Capacity

+5V DC 7A or more.

+12V DC See Figure 1 below

Figure 1:

Required Power Capacity

a

  • Signal output a an R(red) analog, positive a G(green) analog, positive

B(blue) analog, positive TA

Sync. H-V composite negative H Vv

DIAGNOSTIC PROCEDURES

AUTOMATIC SELF-TEST — Upon “Power On”, this system will automatically test ROMS and VIDEO RAMS. The screen will display pass or fail conditions as follows:

TEST PASSEDTEST FAILEDIF TEST FAILS
RAMOKRAMBADRAM= 10E
ZRAM 1 OKZRAM 1 BADZRAM1= 8E
ZRAM 2 OKZRAM 2 BADZRAM2= 8E
ROM 1 OKROM 1 BADROM1= 7C
ROM 2 OKROM 2 BADROM2= 8C
ROM 3 OKROM 3 BADROM 3 = 10C
Page 12

DIP SWITCH SETTINGS

DIP SW No. 1 Settings Coin 1 Switch Set Coin 2 Switch Set

sw4321COIN | PLAYSW8765COIN | PLAY
¢ | oFF | OFF[orF | orF|11«|orr | orr [orr| orr|141
OFF | ON12OFF | ON12
ON | OFF13ON | OFF13
ONON14ONON14
OFF | ON | OFF | OFF15OFF | ON | OFF | OFF15
OFFON16OFFON16
ONOFF17ONOFF17
ONON21ONON21
ONOFF | OFF | OFF23ONOFF | OFF | OFF23
OFF | ON25OFF |} ON2§
ON | OFF31ON | OFF31
ONON32ONON32
ONON | OFF | OFF34ONON | OFF | OFF34
OFFON41OFFON41
ONOFF43ONOFF43
ONONFREE PLAYONONINVALIDITY

DIP SWITCH NO. 2 SETTINGS THE NUMBER OF PLAYER'S LIFE SOUND IN ATTRACT MODE

sw12NUMBERsw8SOUND
OFF | OFF2OFFOFF
.ON | OFF3°ONON

OFF | ON 5

ONON7

CHANGE OF TABLE OR UP-RIGHT

sw Ts errs DIP SWITCH NO. 3 SETTINGS

OFFTABLEVideo Screen Flip
.ONUP-RIGHTSW1
.OFFNORMAL
BONUS SETONUPSIDE DOWN
sw] 4]5FIRSTSECONDTHIRD
lOFF|OFF| — 30,00070,000 | Every 70,000Single/Dual Control Upright
ON |OFF|40,00080,000 | Every 80,000sw | 2TYPE
+ loEFlon|60,000100,000. 1 Every, 100,000*[OFF | SINGLE UPRIGHT CONTROL
ON} ON| — 50,000200,000 | Every 200,000ONDUAL UPRIGHT CONTROL

Difficulty of the Game

swle6|7DIFFICULTY*SW 3 & SW 4: NOT USED

lOFF|OFF EASY e {ON |OFF NORMAL JOFF| ON DIFFICULT

ON | ONaa*SHOWS NORMAL SETTING
Page 13

USER INFORMATION

WARNING

F.C.C. REGULATION COMPLIANCE

THIS KIT IS INTENDED FOR USE ONLY ON COIN-OPERATED VIDEO GAMES MANUFACTURED AFTER OCTOBER 1, 1983 WHICH HAVE BEEN VERIFIED FOR COMPLIANCE WITH RE- QUIREMENTS IN PART 15 OF F.C.C. RULES FOR A CLASS A COMPUTING DEVICE.

IMPROPER CONNECTION OF THIS KIT OR CONNECTION TO ANY OTHER GAME NOT SO MANUFACTURED OR VERIFIED FOR COMPLIANCE MAY CAUSE UNACCEPTABLE INTER- FERENCE TO RADIO AND T.V. RECEPTION, REQUIRING THE OPERATOR TO TAKE WHATEVER STEPS ARE NECESSARY TO CORRECT THE INTERFERENCE.

THE P.C. BOARD CAGE SUPPLIED WITH THIS CONVERSION KIT MUST BE UTILIZED AND TERMINATED TO GROUND AT THE TIME OF INSTALLATION.

Konami.

1555 BRUMMEL AVENUE, ELK GROVE VILLAGE, IL 60007 TELEPHONE: (312) 364-6633 FAX: (312) 364-1368 TELEX: 6871385 KONAM UW