CATHODE RAY TOMES

Major Havoc TM-252 2nd Printing

The Adventures of Major Havoc (Atari, Inc., 1983) · Technical Manual · 76 pages · 72 sections · original scan

Page 1

i

Page 2

If reading through this manual does not lead to solving a certain maintenance problem, call TELEHELP® at the Atari Customer Service office in your geographical area, as shown below.

WEST and CENTRAL U.S.A. Parts and Service

Alar, Inc California Customer Service Office 1105 N. Fair Oaks Avenue P.O. Box 427, Sunnyvale. CA 94086 Telex 17-1103 (Monday-Friday, 7°30-4:00 pm Pacific Time) eg From California, Alaska, or Hawaii oO @@ (408) 745-2900 em Service from anywhere in the area shown in white Oo @@ toll-free (800) 538-1611

EAST USA. Service only

Atari, Inc New Jersey Customer Service Office 12A World's Fair Drive, Somerset, NJ 08873 Telex 37-9347 (Monday-Friday, 7:30-4:00 pm Eastern time) ame =From New Jersey 2° (201) 469-5993 = From anywhere else in this area © toll-free (800) 526-3849

EUROPE _

Parts and Service

Atari Ireland Limited European Customer Service Office Tipperary Town, Ireland Telex 28165 TIPPERARY TOWN, (Monday-Friday, 9:00-6:00 pm GMT) IRELAND

J 06252155

Page 3

The adventures ° yA oA f+ | \ t ABAJO HOPE gi ve \ Operators Hae Ae et ith yustrated P2! rts Lists Wi

Wi “al. ie

Page 4

Major Havoc

© 1983 by Atari, Inc. All rights reserved. No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form ofa phonographic recording, nor may it be stored ina retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher. The game play, ali graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the U.S. Copyright Act of 1976. This Act provides for increased penalties for violating federal copyright laws. Courts can impound infringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles. In addition, the Act provides for payment of statutory damages of up to $250,000 in certain cases. Infringers may also have to pay costs andattorneys’ fees and face an imprisonment of up to five years. Atari wiil aggressively enforce its copyrights against any infringers. We will use all legal means to immediately halt any manufacture, distribution, or operation of a copy of video games made by us. Anyone who purchases such copies risks forfeiting such a game.

Published by: ATARI, INC. 790 Sycamore Drive PO. Box 906 Milpitas, California 95035

Printed in the U.S.A. 3N

Page 5

Notice Regarding Non-ATARI Parts

Use ofnon-ATARI parts or modifications of any ATARI® game circuitry may adversely affect the safety of your game, and may cause injury to you and your players.

You may void the game warranty (printed on the inside back cover of this manual) if you do any of the following: © Substitute non-ATARI parts in the game.

  • Modify or alter any circuits in the game by using kits or parts of supplied by Atari.

NOTE

This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of Federal Communications Commission (FCC) Rules, which are designed to provide reasonable protection against such interference when operated in acommercial environment. Operation of this equipment ina residential area or modification to this equipment is likely to cause interference in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference. If you suspect interference from an ATARI® game at your location, check the following:

  • Allgreen ground wires in the game are properly connected as shown in the game wiring diagram.
  • The power cord is properly plugged into a grounded three-wire outlet. ¢ The game printed-circuit boards (PCB) are properly installed within the Electromagnetic Interference (EMI) cage.
  • The EMI Shield PCB is properly installed and connected in series with the game PCB harness,
  • All filter capacitors required on the EMI Shield PCB are properly soldered in place. If youare still unable to solve the interference problem, please contact ATARI Customer Service. See the inside front cover of this manual for service in your area. Major Havoc

iii

Page 6

Major Havoc

Table of Contents

Set Up How to Use This Manual .. . Game Overview ... New Features... . Installation Requirements .. Inspecting the Game 7 Voltage-Plug Selection and Fuses . . Switch Locations

Self Test Self-Test Displays Self-Test Trouble Analysis . . .

Maintenance Cleaning Requirements ... . Opening the Control Panel . Pushbutton Leaf Switches . . Removing the Roller Control Assembly . . Roller Control Maintenance Reassembling the Roller Control Assembly Replacing the Coupler PCB Assembly . Light and Speaker Board Assembly . Lower Speaker Removing the CRT Assembly Wiring the Utility Panel Controls

Illustrated Parts Lists For a list of all illustrations in this manual, see following page 2-2 2-8

Page 7

List of Hlustrations

Figure 1-1 Figure 1-2 Figure 1-3

Figure 2-1 Figure 2-2 Figure 2-3 Figure 2-4 Figure 2-5 Figure 2-6 Figure 2-7 Figure 2-8 Figure 2-9

Figure 3-1 Figure 3-2 Figure 3-3 Figure 3-4

Figure 4-1 Figure 4-2 Figure 4-3 Figure 4-4 Figure 4-5 Figure 4-6 Figure 4-7 Figure 4-8 Figure 4-9 Figure 4-10 Figure 4-11

Table 1-1 Table 1-2 Table 13

Table 2-1 Table 2-2 Table 2-2 Game Overview 2.00. 6c nee - 12 Voltage-Selection Plug and Fuse Locations . L4 Switch Locations 15

Screen 1: Operator Information Display 23 Screen 2; Alpha Processor Display. . . 2-4 Screen 4: Scaling Test Display... ... 25 Screen 4: Bipolar Offset Test Display 2-5 Screen 5: Crosshatch Pattern Display 26 Screen 6; Color Intensity Test Display . 2-6 Screen 7: Color Intensity Test Display 2-7 Screen 8: Grid Pattern Display .... . 2-7 Self-Test Trouble Analysis . bese 2-8

Control Pane] Opening and Wire Colors 33 Roller Control Assembly Lubrication and Adjustment 3-4 Fluorescent Light and Speaker Board Removal, Display Access 3-7 Utility Panel Wire Colors ..... 3-9

Mustrated Parts Lists Cabinet-Mounted Assemblies Control Panel Assembly . Roller Control Assembly - Fluorescent Tube and Speaker Board Assembly . Utility Panel Assembly ........-.. Coinco Coin Door Assembly .... . . Coin Acceptor Coin Door aaa : Power Supply Assembly .......... PCB Mounting Hardware . Regulator/Audio II PCB Assembly . . Major Havoc PCB Assembly ........-

List of Tables

Installation Specifications.......... seeeeeee 13 Switch Settings for Play Options ... 16 Switch Settings for Price Options . . 1-7

Gamma Microprocessor Faulty Component Locations . . 2-2 Alpha Microprocessor Faulty Component Locations ... . 2-4 ROM Locations of Checksum Errors... .......-..... 2-4 Major Havoc

Page 8

Major Havoc

vi

Safety Summary

The following safety precautions apply to all game operators and service personnel. Specific warnings and cautions will be found throughout this manual where they apply.

A WARNINGS A

Properly Ground the Game. Players may receive an electrical shock if this game is not properly grounded! To avoid electrical shock, do not plug in the game until it has been inspected and properly grounded. This game should only be plugged into a grounded 3-wire outlet, If you have only a 2-wire outlet, we recommend you hire a licensed electrician to install a grounded outlet. Players may receive an electrical shock if the control panel is not properly grounded! After servicing any parts on the panel, check that the grounding clip is firmly secured to the metal tab on the inside of the control panel. Only then should you lock up the game. AC Power Connection. Before connecting the game to the AC power source, verify that the proper voltage-selection plug is installed on the game’s power supply. Disconnect Power During Repairs. To avoid electrical shock, disconnect the game from. the AC power source before removing or repairing any part of the game. When removing or repairing the video display, extra precautions must be taken to avoid electical shock because high voltages may exist within the display circuitry and cathode-ray tube (CRT) even after power has been disconnected. Do not touch internal parts of the display with your hands or metal objects! Always discharge the high voltage from the CRT before servicing this area of the game. To discharge the CRT: Attach one end ofa large, well-insulated, 20-kV jumper to ground. Momentarily touch the free end of the grounded jumper to the anode by sliding it under the anode cap. Wait two minutes and discharge the anode again. Use Only ATARI Parts. To maintain the safety integrity of your ATARI game, do not use non- ATARI parts when repairing the game. Use of non-ATARI parts or other modifications to the game circuitry may adversely affect the safety of your game, and injure you or your players. Handle Fluorescent Tube and CRT With Care. If you drop a fluorescent tube or CRT and it breaks, it may implode! Shattered glass can fly six feet or more from the implosion. Use the Proper Fuses. To avoid electrical shock, use replacement fuses which are specified in the parts list for this game. Replacement fuses must match those replaced in fuse type, voltage rating, and current rating. In addition, the fuse cover must be in place during game operation.

CAUTION

Properly Attach All Connectors. Make sure that the connectors on each printed-circuit board (PCB) are properly plugged in. Note that they are keyed to fit only one way. If they do notslip on easily, do not force them. A reversed connector may damage your game and void the warranty.

Page 9
WARNING Shock Hazard To avoid electrical shock, do not plug in the game until it has been inspected and properly set up for the line voltage in your area. Do not touch internal parts of the display with your hands or metal objects!

Set Up

How to Use This Manual

This manual, written for game operators and service technicians, describes your new Atari game. Chapter 1 contains a game overview, game specifications, inspection procedures, voltage plug and fuse information, switch locations, and option information. Chapter 2 contains self-test procedures, Chapter 3 contains maintenance and repair procedures. Chapter 4 contains illustrated parts lists. Notes in this chapter refer you to other places in the manual for more detailed information. Schematic diagrams of the game circuitry are included as a suppiement to this manual.

Chapter 1

Page 10

Set Up Major Havoc

Lower Speaker See Figure 441

HighVoltage PCB x Used with Atari Display See Display Manual Fluorescent Light & Speaker Board Assy Speaker & Figure 4-9 See Figure 4-4 Deflection PCB x Used with Atari Display Game identification Label * See Display Manual & Figure 4-9

Video Display x | SeeFigure41 |-——— | Access Panel

Control Panel Assy See Figure 4-2

Fan See Figure 4-1 Roller-Contro{ Assembly See Figure 4-3

Regulator/Audio II PCB Assy « See Figures 4-9 & 4-10 Rear Door

Game PCB * See Figures 4-9 & 4-11

Coin Door See Figures 4-6 & 4-7

Utility Panel See Figure 4-5

Power Supply *

See Figure 4-8 Shock Hazard

Do not plug in the game until it has. been inspected. This game should only be connected to a grounded 3.wire oullet, Ifycuhaveonly a2-wire outlet, we recommend you hire a licensed electrician to install a grounded outlet. Players may receive an electrical shock if this game is not properly grounded!

  • Item with a serial number label

Figure 1-1 Game Overview

Page 11

Major Havoc

Game Overview

You are Major Havoc, leader of a brave band of clones. All from one, one from all, fighting for humanity. . . . Eons ago the evil Vaxxian Empire overran the galaxy: Most of your ancestors were enslaved and taken to the Vaxxian homeworld. Only a few scientists escaped. The small band of scientists cloned you, Major Havoc, to fly your Catastrofighter through a wormhole in space, leading your clone army against the dreaded Vaxxian robots to free your people by destroying the enemy reactor.

New Features

High-Tech Game Cabinet. A new video arcade game cabinet design delivers high visibility and increased player attraction. Roller Control. The backlit roller control provides leftto-right and right-to-left directional movement. Multi-Layer Printed-Circuit Board. This state-of-theart design printed-circuit board (PCB) provides low system noise with high system reliability. Game Within a Game. Action occurs in the lower right corner of the TACTICAL SCAN. Breakout® can be played fora few seconds before the actual Major Havoc game play starts. Earn a bonus life here! Dual FIRE/JUMP Button. This dual-action button allows Major Havoc to jump in the maze sequence and to fire at enemy robots in the space wave. Add-A-Coin. This feature permits you to start a new Major Havoc game at the level where you last saw the TACTI- CAL SCAN in your previous game play. Secret Warp Code. The code feature rewards you for short game times as it advances to deep levels in game play. Use the coller control to dial in secret code numbers during the TACTICAL-SCAN wave. All major parts of the cabinet are illustrated in Figure 1-1,

Installation Requirements

Table 1-1 describes the physical, electrical, and environmental specifications of the game.

Table 1-1 Installation Specifications

Characteristic Requirement

Power Consumption 200 W ‘Temperature 0° to +32°C (+32° to +100°F) Humidity Not to exceed 95% relative Line Voltage 100 to 240 VAC Width 64.1 cm (25.25 in.) Depth 80.3 cm(31.6in.) Height 170.8 cm (67.25 in.) Set Up

WARNING To avoid electrical shock, do not plug in the game until you have inspected the game and sefected the appropriate line voltage plug. Do not touch internal parts of the display with your hands or with metal objects!

TANNA

ays

Page 12

SetUp

Inspecting the Game

Please inspect your game carefully to ensure that it was delivered to you in good condition. 1, Examine the exterior of the game cabinet for dents, chips, or broken parts.

  • Remove the screws from the rear access panel. Unlock and open this panel and the coin door. Inspect the interior of the game as follows:

a. Ensure that all plug-in connectors (on the game harnesses) are firmly plugged in. Replug any conneciors found unplugged. Do not force connectors together. The connectors are keyed so they only fit in the proper orientation, A reversed edge connector may damage a printed-circuit board (PCB) and will void your warranty.

b. Ensure thatall plug-in integrated circuits on each PCB are firmly plugged into their sockets.

c. Remove the tie-wrap that secures the coiled power cord inside the cabinet. Inspect the power cord for any cuts or dents in the insulation, Repair or replace it as required. Place the square strain-relief plate in the wood slot at the bottom of the rear panel opening.

Fuse F2 4A, 250V Fuse F3 20A, 32V

Fuses Fa-F6 4A, 250 Major Havoc

d. Inspect the power supply. Make sure the fuse block cover is mounted in place. Check that the green ground wire is connected. e. Inspect other major subassemblies, such as the control panel, video display, EMI cage, and each PCB. Make sure they are mounted securely and that the green ground wires are connected.

Voltage-Plug Selection

and Fuses The power supply in your game contains six fuses. When you replace a fuse, use the identical type fuse with the same electrical rating (see Figure 1-2), This power supply operates on the line voltage of many countries. The power supply comes with cither one, two, or three voltage-selection plugs. Plug voltages and wire colors are 100 VAC (violet wire color), 120 VAC (yellow wire color), 220 VAC (blue wire color), and 240 VAC (brown wire color). See Figure 1-2 for placement of the voltage-selection plug. Before plugging in your game, check your line voltage. Next, check the wire color on the voltage-selection plug. Make sure the voltage-selection plug is correct for the line voltage of your location. Now plug the game into a grounded 3-wire outlet.

VOLTAGE PLUGS

7A,250V

J3

Fuse cover is shown in Figure 4-8

Figure 1-2 Voltage-Selection Plug and Fuse Locations

1-4

Page 13

Major Havoc

Switch Locations

Power On/Off Switch

The power on/off switch is located on the back of the cabinet on the lower left side (see Figure 1-1).

Utility Panel Switches The volume control, coin counter(s), self-test switch, and auxiliary coin switch are on the utility panel. The utility panel is located inside the upper coin door (see Figure 1-1). The volume control adjusts the level of sound produced by the game. The coin counter(s) records the number of coins entered into the game. The self-test switch initiates

Coin Counter

Utility Self-Test ee

Panel Switch

Volume Control Set Up

the self-test mode. The auxiliary coin switch credits the game without activating a coin counter. See Figures 1-3 and 4-5 for details of these switches.

Option Switches

Major Havoc has two option switches. Figure 1-3 shows the location of these dual-inline-package (DIP) switches on the game printed-circuit board (PCB).

  • Option switch SW1 at 13/148 controls game play options, © Option switch SW2 at 85 controls whether the coins are counted on 1 or 2 counters.

Auxiliary Coin Switch

Game PCB

Figure 1-3. Switch Locations

Page 14

Set Up

Selecting the Coin, Credit, and Game Options

Settings for option switches are listed in Tables 1-2 and 1-3. Options preset at the factory are shown by the “4 symbol, however, you may change settings according to your needs. Major Havoc

To verify other option selections, check the Operator Information Display that appears when you enter the Self- Test Mode, See Chapter 2 for details.

Table 1-2 Switch Settings for Play Options

Settings of 8-Toggle Switch on Game PCB (SW1 at location 13/148) i 2

345678Option

Starting Lives

Free Play1 Coin Setting2 Coin Setting,
OffOff235<
OnOn4S44
OnOff456
OffOn567

Game Difficulty

OnOnHard
OffOffMedium
OffOnEasy

On Off Demo

Bonus Life

OnOnBonus Life at 50,000 points
OffOffBonus Life at 100,000 points
OffOnBonus Life at 200,000 points

On Off No Bonus Life

On Off

On Off Attract Mode Sound Silence Sound<4

Adaptive Difficulty’ No ‘Yes

4Manufacturer’s recommended settings

  • Game difficulty increases with player skill level
Page 15

Major Havoc Set Up

Table 1-3 Switch Settings for Price Options

Settings of 8-Toggle Switch on Game PCB (SW2 at location 8S) 1 3 4 7 Option

OnOffFree Play
offOff.1 coin for 1 game (or 1 player)
OnOn1 coin for 2 games (or 2 player)
OffOn2.coins for 1 game (or | player<4

Off Off On On

Off On

Off Off Off

Off On Off

Off On On

On Off Off

On Off On

Off On Off On Right Coin Mechanism Right coin mech x 1<4 Right coin mech x 4 Right coin mech x 5 Right coin mech x 6

Left Coin Mechanism Left coin mech x 14 Left coin mech x 2

Bonus Coin Adder No Bonus coins<4 For every 4 coins, game logic adds 1 coin For every 4 coins, game logic adds 2 coins For every 5 coins, game logic adds 1 coin For every 3 coins, game logic adds 1 coin

2-Coin Minimum"

“4Manufacturer’s recommended settings

* This game bas the ability to select the 2-coin-minimum capability, which

requires the player to pay for wo games in advance. If you want this caability, short pin 6 on 13N to ground by soldering a short piece of wire from ground to this point.

Page 16

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 17

Self Test

This game will test itself and provide data to show that the game circuitry and controls are operating properly. Selftest data is presented visually on the video display and audibly through the speakers. No additional equipment is required. We suggest you perform a self-test when you first set up, each time you collect money, change the game options, or suspect game failure.

Chapter 2

Page 18

Self Test

Self-Test Displays

The self-test switch and the auxiliary coin switch are located on the utility panel inside the coin door. The option switches are on the game printed-citcuit board (see Figure 1-3). Enter the Self‘Test Mode by turning on the self-test switch. When the self-test switch is turned on during Attract, Ready-to-Play, or Game Play Modes, the game will go to the Operator Information Display (see Screen 1 of SelfTest Mode), which also contains the gamma microprocessor display (see Figure 2-1).

Screen 1: Operator Information Display This display shows the condition of the RAM and ROM for the gamma microprocessor. If there is a RAM or ROM failure, the display will identify the failed component and give its location. See Table 2-1 for the location of the failed gamma microprocessor component on the game PCB.

NOTE The following self-test displays are arranged in the sequence in which they occur after the selftest switch is set to the on position. Press the auxiliary coin switch to end each display and obtain the next display. If the self-test procedures are not performed in sequence, pressing the auxiliary coin switch will advance the game through the displays until the desired display is obtained. If the game is turned on with the self-test switch in the on position, the game will go directly to the Operator Information Display. Major Havoc

To return to the Attract Mode, turn off the self-test switch.

+» NOTE The game-reset circuitry must be operating or the game will lock up with a blank screen. Ifa locked condition occurs, turn the self-test switch offand turn the game off and back on. If the game does not restart after this action, troubleshooting of the game-reset circuitry may be necessary.

Table 2-1 Gamma Microprocessor Faulty Component Locations

IdentifierMeaningLocation
RGamma RAM ErroroPIQ
fe)Gamma ROM Ertor98
PCustom IC Error13Q
EEEROM Error9QIR
Page 19

Major Havoc

Gamma Microprocessor Error See Table 21

Adaptive Difficulty Game difficulty increases with player skill level.

Coin Mode

SWi at 13/148

Roller Control Position

Command Number to Gamma Microprocessor

Press SHIELD button to advance through sounds or functions.

Press FIRE/JUMP button to activate the sound or function.

Reset High Scores Activating this function replaces the game High-Score Table with the default set of high scores. To see the High-Scare Table, enter the Attract Mode and spin the Roller Control to the left. Spin the Roller Control to the right to reenter the Attract Mode. Bonus Life Earned Every xx Points To reset high scores to default set: " tings, hold down the right coin switch. Then, depress and release FIRE/JUMP button. You will hear a loud hissing sound. Wait for this sound to finish before exiting self test. Wait 10 seconds before turning the game off or leaving the SelfTest Mode.

Left Coin Counter

Right Coin Counter Sounds Off

Sound Values

Figure 2-1 Screen 1: Operator Information Display Self Test

2-Coin-Minimum Option

Attraction Sounds

FIRE/JUMP

SHIELD

Game Difficulty Level

No. of Lives per Play

Page 20

Self Test

Screen 2: Alpha Microprocessor

Test Display The alpha microprocessor is responsible for much of the game play. Table 2-2 helps you determine the location of a faulty RAM on the game PCB.

Table 2-2. Alpha Microprocessor Faulty Component Locations

Iden-Hex LocationDefinitionPCB

tifier Location

A0000-07FFRAM ErrorWk
BQ800-O8FF &RAM1HiT

Swap 0200-0700

CcVector Gen.—LowRAM Error6M/N

D VectorGen.—High = RAMError ~— 6L/M

ECommun, RAMErrorIF

ROM Checksums

See Table 2-3 to determine the ROM location of a checksum error in the alpha microprocessor,

RAM Locations See Table 2-2

E Always Appears; Checksum Error ROM Locations snes See Table 2-3 Major Havoc

NOTE If the ROM checksum is correct, neither the self-test ROM identifier (a single character) nor the checksum (a double character) appears on the screen.

Yable 2-3 ROM Locations of Checksum Errors

Identifier PCB Location

iN/P IN/P 1Q 1Q ig IMIN* ik GK 6H oH OKILY OE NeEKRYAUHOD

  • This ROM must be good for self test to function,

Auxiliary Coin Counter

Left Coin Mechanism

Not Used

Not Used Not Used Right Coin Mechanism

Not Used

2-Coin-Minimum Option

Figure 2-2 Screen 2: Alpha Processor Display

2-4

Page 21

Major Havoc

Screen 3: Scaling Test Display

Ared outline frames the sides of the screen during this test. Inside this red outline a white box of decreasing size appears inside a white frame. The white box should shrink smoothly and disappear into the center indicator on the screen, If asudden change in the size of the square occurs, an error may exist. This sequence will repeat indefinitely until you press the auxiliary coin switch. This pattern tests the binary and linear scaling circuitry.

Figure 2-3 Screen 3: Scaling

Test Display

Self Test

Screen 4: Bipolar Offset Test Display

NOTE This procedure should be performed only after the game has been on for at least 15 minutes to ensure that the game PCB is fully warmed up.

Press the auxiliary coin switch to obtain the Bipolar Offset Test (BIP) Display as shown in Figure 2-4. The lines in the center of the screen should cleanly overlap to forma single orange square. If you see red and green lines, adjust the Xand Y bipolar offset potentiometers as describedon the Linear Scaling schematic diagram in the Schematic Package Supplement (SP-252). These potentiometers are designated XBIP (R80) and YBIP (R81). The upper righthand corner of the orange square is the critical adjustment point.

Orange

Figure 2-4 Screen 4: Bipolar Offset

2-5

Page 22

Self Test

Screen 5: Crosshatch Pattern Display

Press the auxiliary coin switch to obtain the Crosshatch Pattern Display as shown in Figure 2-5. Verify the following display characteristics:

  • All four corners of the red outline must be off the screen, while all four corners of the white outline are completely visible. if not, adjust potentiometers XSIZE (R34), YSIZE (R48), XCENTER (R39), and YCENTER (R55)as described on the X and Y Output schematic diagram in the Schematic Package Supplement (SP-252).
  • ~Awhite frame filled with a crosshatch pattern appears inside the red outiine. *® The crosshatch corners are closed and the diagonal lines form symmetrical diamond-shaped squares. These lines should be straight within #,-inch over their length (visually straight is satisfactory). If otherwise, adjust potentiometers XLINEARITY (R38) and YLINEARITY (R50) as described on the X and Y Out put schematic diagram in the Schematic Package Supplement (SP-252).
  • The crosshatch pattern is not tilted more than % -inch between corners. ° The pattern is a uniform white color. ¢ = Aline of alphanumeric characters stretches across the display.

Figure 2-5 Screen 5: Crosshatch

Pattern Display

Major Havoc

Screen 6: Color Intensity Test Display

Press the auxiliary coin switch to obtain the Color Intensity Test Display as shown in Figure 2-6. Verify the following display characteristics: © Top row of color bars red, blue, and green. ¢ All three sets of color bars have six lines dim at the top and increasing in intensity at the bottom. © Bars underneath the top row of color barsare white. Bars underneath the white color are yellow, light blue, and purple.

Figure 2-6 Screen 6: Color Iatensity Test Display

This test checks the seven screen colors and six intensities of each color. If the intensities do not progress from dim atthe top of each color group to bright at the bottom, there isa problem inthe Z-axis of the game PCB or in the video display. If the colors are not as described, there is a problem with the red, green, or blue output of the game PCB or with the video display circuitry. Use this pattern for tracking adjustments and for brightness adjustment. Refer to the Color XY Display Manual for the brightness adjustment procedure or to determine the possible cause of failure.

Page 23

Major Havoc

Screen 7: Color Intensity Test Display

Press the auxiliary coin switch to obtain the Color Intensity Test Display as shown in Figure 2-7. Sixteen intensities (15 visible and 1 with zero intensity) of each of 16 colors are displayed. One color is black, resulting in an empty column. Every location in the color RAM is used. Use this screen for vector generator and color RAM troubieshooting. Do not use it for adjustment or quality checking. Self Test

Screen 8: Grid Pattern Display

Press the auxiliary coin switch to obtain the Grid Pattern Display outlined in red as shown in Figure 2-8. Use this display to check for proper convergence and color purity. The horizonul lines may or may not touch the right side of the square.

{J —E ~

Figure 2-7 Screen 7: Color Intensity

Test Display

Figure 2-8 Screen 8: Grid

Pattern Display

2-7

Page 24

Self Test Major Havoc

Self-Test Trouble Analysis

Figure 2-9 provides a trouble analysis diagram to help you use the Self-Test Mode to determine the probable cause of trouble and the possible remedies.

NOTE Tne game-reset circuitry must be operating or the game willlock up with a blank screen. Ifalockedcondition ever occurs, turn the self-test switch off. Then turnthe game offand back on. Ifthe game doesnot restart after this action, troubleshooting of the game reset circuitry may be necessary.

up = microprocessor STEP 1

Turn on game. Gelt-test switch is off.) Gamma ypis bad and unable to fespond. Gamma ,p must be checked out. Go to START.

Attract Mode is OK.

STEP 2 Does sereen flash “@" after 4or5 sec. Fatal gamma up error. Possible bad 1H/J {alpha zero page RAM). Replace & go to START. (Lack of lashing in STEP 1 indicates no gamma xp error.)

No fatal gamma up errors Screens blank & no sounds audible.

Wait 4 or 5 seconds for alpha up Low tones = Replace 6K/L (Vector ROM). 5 high tones = Replace &M/N (Vector RAM). Many tones (~ 75)= Replace 14/K (Vector ROM). Screen is blank & sound is audible. Press auxiliary coin switch to advance to Operator information Display.

R, 0,8, or Eat top of screen. R = Replace 9P/Q (Gamma RAM). 0 = Replace 9S (Gamma ROM). Replace 130 (Custom IC), E = Replace 9Q/R (EEROM).

Press auxiliary coin switch to advance to Alpha up Test Display.

Sev Tabie 2-2 for bad IC if A, 8, C, or D appear at top of screen. E will always appear, ignore E.

‘See Table 2-3 for bad ROMs if 3 digits appear

above the lines of 1's & 0's. Display does not match Fig. 2-2 Inspect Alpha Test Display.

Press auxiliary coin switch toadvance to ‘Scaling Test Display.

Error has occurred in the Vector Generator Scaling circuit. Digital circuit problem possible, but not likely. Slow shrinking square is not same as Fig. 2-3.

Figure 2-9 Self-Test Trouble Analysis Diagram

2-8

Page 25

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 26

Major Havoc Self Test

Press auxiliary coin switch to advance to BIP Display.

(Assumes red/white borders are same as, Inspect BIP Fig.2-4,) If multiple green vertical

Display. lines appear, adjust R80. If multiple green

horizontal lines appear, adjust R81. Isnot as shown in Fig.2-4.

Press auxiliary coin switch to advance to Crosshatch Display.

Ifred outline is VISIBLE at all 4 comers, or tsnot as described in text describing Fig. 2-5. white outline is NOT VISIBLE: adjust R34, R39, 48, & R56. If crosshatch lines are not straight: adjusth38 & R50. If pattern is not uniform in color: see Display Manual for purity Press auxiliary coin switch adjustment. to advar to Color intensity Display—Screen 7.

lanotenovange sguare. If colors are incorrect: possible color RAM er- Inspect Color ge square. ror at 12J OR 12K (Do next test.), or red, green,

Display—t. orblue output error. If intensities are incorrect:

see Display Manual for brightness adjustment,

Press auxiliary coin switch to advance to Color Intensity Display—Screen 2.

Many repeating cotors appear, or Inspect Color colors all are same. Itcolors are incorrect here & in last test: check

Display—2. Fed, green, and blue output circuitry RAMs at

120 & 12K for possible errors.

Press auxiliary coin switch to advance to Grid Pattern Display.

Obvious color smearing or color changes Inspect Grid ina single screen. See Display Manual for purity & convergence Display. adjustments.

END OF SELF TEST Game reset circuitry (WATCHDOG) Is not a nk Screen operating. (The program re-enters the Game wr rm ‘oatuact thet 7 Mode from Self-Test Mode by purposely failing " to reset the WATCHDOG circuit, which THEN forces the RESET line down.) Attract Mode

Figure 2-9 Self-Test Trouble Analysis Diagram, continued.

Page 27

Maintenance

The maintenance procedures provided in this chapterare for those items which are subject to the most severe use. To assure the maximum trouble-free operation from this game, Atari recommends that periodic routine maintenance be performed on the game components described in the following procedures. How often routine maintenance is performed depends upon the game environment and frequency of play. ‘To avoid possible electrical shock hazard, unplug the game prior to performing any maintenance.

Chapter 3

Page 28

Maintenance

Cleaning Requirements

This game cabinet and the display shield may be cleaned with any non-abrasive household cleaner. A toothbrush may be used to remove any stubborn build-up of residue in the coin path, on the plastic roller, or drive and idler shafts of the roller control. Be sure to lubricate the shaft bearings after cleaning. Compressed air is also recommended for cleaning dust from the interior of the cabinet.

Opening the Control Panel

Perform the following procedure to open the control panel:

  • Unlock and open the coin door. Reach up through the coin-door opening to the top of the front panel and release the spring-draw latch (see Figure 3-1).
  • Close the coin door.
  • Lift the front of the control panel by exerting upward pressure on both sides. Slide it forward and tilt it toward you.
  • Hook the control panel over the froat of the cabinet using the bracket thar is part of the black aluminum. control-panel cap (see Figure 3-1).
  • Disconnect the control harness before moving the control panel to a work surface.

Pushbutton Leaf Switches

i, With the control panel open, adjust the leaf switch contacts for a narrow gap. Don't burnish the contacts. ‘To clean them, use electrical contact cleaner.

  • To seplace a leaf switch, remove the screw with a Phillips-head screwdriver.
  • To remove the switch pushbutton, turn the stamped nut with a wrench ina counterclockwise direction, as seen from the inside of the control panel. The ring on the outside of the control panel should not spin. 4, Reinstall the pushbutton switch. Reconnect the harness wires to the switch terminalis as shown in Figure 3-1.

Removing the Roller-Control Assembly

Perform the following procedure to remove the roller control from the control panel:

  • Open the control panelas previously described in this chapter and disconnect the wires from the lamp socket. Disconnect the harness at the four-pin connector on the coupier PCB assembly.

3-2 Major Havoc

  • Remove the nuts and carriage bolts that secure the rolier-control assembly to the control panel (see Figure 3-1).

Roller-Control Maintenance

Routine preventive maintenance of the roller-control assembly consists primarily of lubricating the shaft bearings and checking the mounting screws and washers for proper tightness approximately every four months. The roller-control assembly consists ofa roller, a drive shaft, an. idier shaft, upper and lower frames, and a coupler PCB assembly. Refer to Figure 3-2 for the location of the parts mentioned in the following procedures.

Routine Maintenance and Disassembly

1, Open the control panel and remove the roller-control assembly as previously described in this chapter. 2, Use a Phillips-head screwdriver to remove the panhead screws that secure the upper and lower frames (see Figure 3-2).

  • Carefully lift the upper frame straight up from the assembly.
CAUTION Be sure to keep the drive studs in the upper frame. They must be in place during reassembly or the roller will not function.

4, Remove the plastic roller. Apply two drops ofa light machine oil, such as 3-In- One oil, to the inside of the four shaft bearings. Wipe off any excess oil from the shafts.

  • The contact area of the drive shaft may have dirt buildup from use. Remove the residue as previously described in this chapter under Cleaning Requirements.
  • Use the appropriate hex-head wrench to check the tightness of the socket-head screw that secures the encoding wheel to the drive shaft. Use a pin or small screwdriver to steady the shaft. Refer to Figure 3-2 for an illustration of the the shaft screw location,
  • Liftthe idler shaft and bearings from the lower frame. Be careful not to lose the bearings.
  • Slide the bearings off each end of the idler shaft.
  • Wipe off any dirt build-up from the shaft with a soft clean cloth. Il. Lift the drive shaft with bearings and encoding wheel from the lower frame. Be careful not to lose the end bearing.
Page 29

Major Havoc Maintenance

Control Panel

FIRE/JUMP Switch Wire Colors: Roller-Control Assy. Yellow & Black

SHIELD Switch Wire Colors: Green & Black

Carriage Bolts & Nuts Ground Wire: Green

Control-Panel Cap

Lamp Wire Colors: Gray & Orange

Figure 3-1 Control Panel Opening and Wire Colors

3-3

Page 30

Maintenance

Roller

Ball Bearing

Drive Shaft

3-4 ™~,, Major Havoc

Upper Frame

Hole in Drive Shaft

Encoding Wheel

‘Socket-Head Screw

Optical Coupler

a Coupler PCB

Alien Wrench

Slot for PCB

Figure 3-2 Roller-Control Assembly Lubrication and Adjustment

Page 31

Major Havoc

12.

13.

14,

15. Remove the metal encoding wheel by loosening the socket-head screw with an Allen wrench. Be careful not to lose the two small washers and screw. Gently slide the other bearing off the end of the drive shaft. Wipe off any dirt build-up from the shaft with a soft clean cloth. Reassemble the roller-control assembly as described in the following procedure.

Reassembling the Roller-Control Assembly

Perform the following procedure to reassemble the roller control (See Figure 3-2):

SN AW Remount the bearings, encoding wheel, washers, and socket-head screw on the drive shaft. Reinstall the drive shaft in the lower frame. Refer to Figure 3-2 and tighten the encoding wheel by inserting a %-inch diameter pin or screwdriver through the hole in the shaft. Tighten the socket-head screw with an Allen wrench. Remount the bearings on each end of the idler shaft. Reinstall the idler shaft in the lower frame. Reinstall the plastic roller in the lower frame. Reinstall the coupler PCB assembly in the lower frame. Position the upper frame over the lower frame so the four screw holes are aligned and the coupler PCB assembly is secured.

CAUTION Be sure to keep the drive studs in the upper frame. They must be in place during reassembly or the roller will not function.

Use a Phillips-head screwdriver to tighten the four screws securing the upper and lower frames to each other. Maintenance

. Reinstall the roller-control assembly in the control panel using the nuts and carriage bolts. . Reconnect the control harness, . Reconnect the wires to the lamp socket.

Replacing the Coupler PCB Assembly

To replace the coupler PCB assembly after the rollercontrol assembly has been removed from the control panel and disassembled, perform the following procedure (see Figure 3-2): Disconnect the four-pin connector and lift the coupler PCB assembly from its slot. ‘To reinstall the coupler PCB assembly, place the PCB in the slot in the lower frame and reconnect the fourpin connector.

CAUTION ‘When you reinstall the coupler PCB assembly, make sure that the metal encoding wheel is not bent or damaged. Be sure the encoding wheel turns freely between the two halves of the radial optical coupler.

Light and Speaker Board Assembly

Removing the Light and Speaker Board Assembly Perform the following procedure to remove the light and speaker board assembly from the game (see Figure 3-3): Remove the screws from the rear access panel of the game cabinet with a Phillips-head screwdriver.

3-5

Page 32

Maintenance

  • Disconnect the harnesses from the fluorescent light assembly and from the speakers.
  • From the front of the cabinet, use an Allen wrench to remove the screws from the attraction shield upper retainer. 4, Slide both the attraction shield and the semi-rigid film that is behind the shield up and out of the extruded metal speaker grilles.
NOTE Aplastic U-shaped molding is firmly fittedon each side of the attraction shield and on each side of the display shield. These moldings should stay on when you remove the shields.
  • Remove the H-shaped retainer between the attraction shield and the display shield.
  • Slide the display shield up and out of the extruded metal speaker grilles. Carefully remove the display bezel. Remove the screws securing the extruded metal speaker grilles to the cabinet walls on both sides of the video display.
  • Remove the screws securing the light-and-speakerboard cleat to the display shelfat the top of the display.
  • From the back of the cabinet, remove the screws securing the light and speaker board to the side cleats. Ml. Pull the fluorescent light and speaker board assembly out of the front of the cabinet.

Speaker Replacement

To replace either of the speakers attached to the light and speaker board, you must first remove the fluorescent light and speaker board assembly from the game cabinet (see Figure 3-3). Perform the following procedure to replace a speaker: 1, Remove the fluorescent light and speaker board assembly as previously described.

  • With the fluorescent light and speaker boardassembly out of the cabinet, disconnect the two snap-on connectors from each speaker.
  • Remove the hardware securing each speaker to its mounting grille/bracket.
  • Mounteach new speaker to its mounting grille/bracket with the appropriate hardware.
  • Reconnect the snap-on connectors to each speaker. The white wire connects to the positive (+) terminal on the left speaker. The brown wire goes on the negative (unmarked) terminal on the right speaker (see the wiring diagram in $P-252).

3-6 Major Havoc

NOTE The positive terminal on the speaker is marked with either a plus sign (+) ora painted red dot.

Reinstalling the Fluorescent Light and

Speaker Board Assembly

  • Carefully slide the Ruorescent light and speaker board assembly into the upper front of the cabinet.
  • Replace the screws securing the lightand-speaker-board cleat to the display shelf at the top of the display.
  • From the back of the cabinet, replace the screws securing the light and speaker board to the side cleats.
  • From the front of the cabinet, reinstall the extruded metal speaker grilles on both sides of the video display with the appropriate hardware.
  • Slide the bottom edge of the video-display bezel into the retaining slot at the bottom of the cabinet head. Position the remaining three sides of the bezel in place around the video display.
  • Replace the video display shield (with the plastic moldings attached) by sliding the bottom edge into the slots of the extruded metal speaker grilles on either side of the video display.
  • Slide the attraction panel (with the plastic moldings attached) and semi-rigid film into the speaker grilles in front of the fluorescent light and speaker board assembly.
  • Use an Allen wrench to replace the hardware that secures the attraction shield upper retainer to the cabinet.
  • From the back of the cabinet, reconnect the 3-pin connector to the fluorescent light hamess and the 2-pin connector to each speaker.
  • Use a Phillips-head screwdriver to replace the hardware that secures the upper access panel to the cabinet.
CAUTION This speaker is held by wedge only at the top. When reinstalling, slide the top of the speaker into the wedge before centering it over the panel opening and replacing the screws.

Lower Speaker

Access to the lower speaker is from inside the back of the cabinet (see Figure 3-3). Disconnect the speaker harness and the two snap-on connectors. Remove the screws securing the speaker to the speaker panel. The lower speaker grille may be removed from the front of the cabinet only with a square-drive screwdriver. The grille should be considered permanently installed.

Page 33

Major Havoc Maintenance

Retainer

Attraction Shietd Molding

Fluorescent Light & Speaker Board Assy i} ~~. fens nether . Iz Speaker Grille : 7] a : : Mounting Bracket

Anode Cap

Connector

Lower Retainer

Lower Speaker

Display Shield Lower Speaker Grille

Molding ‘Speaker Grille

Figure 3-3 Fluorescent Light and Speaker Board Removal, Display Access

3-7

Page 34

Maintenance

Removing the CRT Assembly

WARNINGS High Voltage This display contains high voltages capable of delivering iethal quantities of energy. To avoid

danger, do not attempt to service the display until you have observed all precautions necessary for working on high-voltage equipment. X-Radiation This display has been designed for minimum X-radiation hazard. However, to avoid possible exposure to soft X-radiation, never modify the high-voltage circuitry. Implosion Hazard The cathode-ray tube assembly may implode ifstruck or dropped. Shattered glass may cause personal injury within a 6-foot radius. To reduce the risks of injury to people or of damage to the game components, we recommend that two people perform the following removal procedures,

Perform the following procedure to remove the cathodetay tube (CRT) assembly from the game (see Figure 3-3): 1, Remove the rear access panel from the cabinet.

  • Discharge the high-voltage from the CRT before proceeding. The video display contains a circuit for discharging the CRT high voltage to ground when power is removed. However, to make certain, always discharge the CRT as follows: a. Attach one end ofa large, well insulated, 18-gauge jumper wire to ground. b. Momentarily touch the free end of the grounded jumper to the anode by sliding it under the anode cap.

3-8 Major Havoc

¢. Wait two minutes and repeat part b. 3, Disconnect the CRT neck-pin connector, anode lead, yoke connector, degaussing coil connector, and 1-pin DAG spring connector (see Figure 3-3). 4, Follow steps 1 through 8 under Removing the Light and Speaker Board Assembly.

CAUTION Be extremely careful when removing the cathode-ray tube mounting bolts because the cathode-ray tube assembly can fall. We recommend that asecond person carefully hold the cathode-ray-tube neck while the mounting bolts are being removed.
  • Use a %4-inch combination wrench to remove the bolis and washers from the front of the display mounting bracket.
  • Carefully lift the CRT assembly from the front of the cabinet.
  • Replace in reverse order.
NOTE Whenever the cathode-ray tube is replaced, readjust the brightness, purity, and convergence as described in the display manual.

Wiring the Utility Panel

Controls

Refer to Figure 3-4 for the proper wire connections when replacing the controls that are mounted on the utility panel.

Figure 3-4 Utility Panel Wire Colors will follow the above text. Be sure the warning is on the illus.

Page 35

Major Havoc Maintenance

Before removing or repairing the util ty panel, turn the game off. Players may receivean electrical shockifthe utility panelis not properly grounded! After servicing any parts onthe panel, make sure that the ground wireis firmly attached to the back of the coin counter.

Orange/White Blue Right Coin Counter Orange/White Violet Left Coin Counter S O\ \ Grounding Clip RON

A002465-01 Coin Counter White/Yellow

White/Red

176018-002 Screw

69-001 Self-Test Switch 75-9910WO Stamped Nut

62-041 Auxiliary Coin Switch

Black Common Gray (Normally Open)

Figure 3-4 Utility Panel Wire Colors

3-9

Page 36

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 37

Illustrated Parts Lists

This chapter provides information you need to order parts for your game. Common hardware (screws, nuts, washers, etc.) has been deleted from most of the parts lists. However, a parts list is included for the hardware to mount the printed-circuit boards (PCB) to the cabinet. The PCB parts lists are arranged in alphabetical order by component. Each component subsection is arranged alphanumerically by reference designator. Other parts lists are arranged alphanumerically by Atari part number. In these parts lists, ali A-prefix numbers come first. Following these are numbers in sequence evaluated up to the hyphen, namely 00- through 99-, then 000598through approximately 201000-. When ordering parts, please give the part number, part name, number of this manual, and serial number of your game. This will aid in filling your order rapidly and correctly. We hope the results will be less downtime and more profit from your game. Atari Customer Service numbers are listed on the inside front cover of this manual.

Chapter 4

Page 38

Ulustrated Parts Lists Major Havoc

006008-05 041249-01 Molding Upper Retainer A200009-02 Atari Display Assy See the Display Manual 041265-01 and Figure 4-9 Attraction Shield

ee

041256-1715 ed 041261-01 H-Shaped Retainer Fluorescent Tube & Speaker Board Assy See Figure 4-4

201018-01 CRT Bracket

041130-01 Left Speaker Grille

041250-01 Lower Retainer

148001-013 041254.01 Speaker Display Shield

041333-01 Speaker Grille

041130-02 Right Speaker Grille

Coin Door See Figures 4-6 & 44 jee Figures 4-6 & 4-7 Utility Panel See Figure 4-5

038091-01 Coin Box

178034-024 178127-036 Molding TMolding

Figure 4-1 Cabinet-Mounted Assemblies A041300-01 A

Page 39

et

vet Major Havoc Illustrated Parts Lists

A041309-01 Fan/Harness Assy 178034-024 Molding A041341-01 Fan Hamess

171002-001 Fan A041301-01 Cabinet Assy A041303-01

Delection PCB Assy See the Display Manual and Figure 4.9

041240-01 High-Voltage PCB Assy 041251-01 Access Panel ‘See the Display Manual Ventilation Grille and Figure 4-9

%

Control Panel Assy See Figure 4-2 178013-001 " A041336-01 Latch Main Harness Roller-Control Assembly 041232-02 See Figure 4-3 Rear Door

‘A038881-01 Lock

Reguletor/Audio. PCB Assy Game PCB See Figure 410 See Figures 4-9 and 4-11

a 041253-01 A041302-01 ie Hinge Body Assy

/ A041338-01 038870-01 Power On/Off Switch Coin Box Enclosure

I 'A037453-01 : 041251-01 THROS# 024 Ventilation Grille Bowler Gore Molding Power Supply See Figure 4.8 A041337-01 Game Publications—

Figure 4-1 Cabinet-Mounted Assemblies, continued A041300-01 A

Page 40

Illustrated Parts Lists Major Havoc

Cabinet-Mounted Assemblies Parts List

Part No. Description

A037453-01Strain-Relief Power Cord(U.S. and Canada)

A038881-01 Lock (for rear door panel of pedestal) Acceptable substitute is part no. A038881-03 A041309-01 Fan and Harness Assembly—consists of A041341-01 Fan Harness 85-22F805 #8-32 x 0.31-Inch Cross-Recessed Type F Screw (not shown) 171002-001 10 V Exhaust Fan A041336-01 Main Harness A041337-01 Power Harness A040699-01 Power On/Off Switch, Harness, and Mounting Plate Assembly

A041301-01 Cabinet Assembly—consists of A041302-01 Body Assembly A041303-01 Head Assembly

A200009-02 ATARI 19-Inch Color XY Display Kit Assembly—consists of A201106-01 Cathode-Ray Tube Assembly (not shown) A201014-01 Deflection PCB Assembly A201012-01 HighNoltage PCB Assembly

The following five items are technical information supplements to this game: SP-252 Major Havoc Schematic Package ST252-01 Major Havoc Label with Self‘fest Procedure and Option Switch Settings T™M-239 ATARI 19-Inch and 25-Inch Color X-Y Display Manual TM-252 Major Havoc Operators Manual TM-248, Star Tech Journal Subscription Card

78-3201 Adjustable Glide 78-6900402 Vinyl Foam Single-Coated Adhesive ‘Tape, ‘4-Inch Wide x %-Inch Thick (36 inches required; used along top and bottom edge of display shield) 006008-04 Display Shield Extruded Plastic Molding 006008-05 Attraction Glass Extruded Plastic Molding. 009992-01 On/Off Switch Cover (not shown)

034536-02Ye-Inch Thick Foam Pad(located between the High-Voltage PCB and the cabinet wall, and between the

Regulator/Audio PCB and the cabinet wall—not shown

034536-031.12-Inch Thick Foam Pad(located between the Deflection PCB and the cabinet wall—not shown)

037243-01 Base Plate for Power Supply (not shown) 038091-01 Molded Coin Box 038870-01 Coin Box Enclosure 041130-01 Left Speaker Grille 041130-02 Right Speaker Grille

041232-02 Rear Door for Pedestal Assembly (does not include lock or hinges) 041240-01 Rear Access Panel for Head Assembly 041249-01 ‘Attraction Shield Upper Retainer 041250-01 Display Shield Lower Retainer 04125101 Ventilation Grille (one located in floor of head assembly; one located in lower rear body assembly) 041253-01 Hinge for Rear Door of Pedestal Assembly 041254-01 Display Shield 041255-01 Attraction Shield

(continued on next page)

Page 41

Major Havoc Illustrated Parts Lists

Cabinet-Mounted Assemblies Parts List, continued

Description

041256-1715 041261-01 041318-02 041333-01

148001-013, 178013-001 178034-024

178127-036

179125-001 201018-01 H-Shaped Retainer for Attraction Glass and Display Shield Video Display Bezel Semi-Rigid Attraction Film with Graphics (not shown) Speaker Grille

6 x 9-Inch Oval, 4-Ohm, 6-Ounce Shielded High-Fidelity Speaker (located above control panel) Spring-Draw Latch 34-Inch Black Plastic TMolding (21 inches required on front of pedestal base; 168 inches required on the side panels of the head assembly; 104 inches required on the side panels of the body assembly; 94 inches required on the front panel of the body assembly) 2 %-Inch Black Plastic TMolding (68 inches required on the pedestal)

Grounding Clip on Main Harness (not shown) 19-Inch CRT Bracket

Page 42

Ilustrated Parts Lists Major Havoc

75-9910NO Nut

160013-001 Leaf Switch & 177010-240 Button Holder Locknult 178030-004 75-5144B Red Pushbution Bolt Roller-Control Assembly See Figure 4-3

041316-01 Control Panel

A041311-01 Control Panel with Decal

178030-007 Yellow Pushbutton

179125-001 Grounding Clip

041247-01 Control Panel Cap 72-5508 Screw

75-045S ‘Washer A041338-01 Harness Players may receive an electrical shock ifthis control panelis not properly grounded! After servicing any parts on the panel, make sure that tne grounding clip is secured to the metal tab on the inside of the control panel.

Figure 4-2 Control Panel Assembly A041310-01 A

4-6

Page 43

Major Havoc IMlustrated Parts Lists

Control Panel Assembly Parts List

Part No. Description

A039421-02 Roller-Control Assembly A041311-01 Control Panel with Decal—consists of 041316-01 Control Panel 041317-03 Decal (not shown)

A041338-01 Control Harness 72-5508 %-Inch-20 x ¥%2-Inch Hex-Head Machine Screw 75-0458 Y4-Inch Split-Lock Washer 75-5144B #10-24 x 2,.75-Inch Black Carriage Bolt

75-9910NO %-Inch-ll Stamped Nut 04124701 Control Panel Cap 160013-001 Leaf Switch with Button Hoider 177010-240 #10-24 Hex Locknut

178030-004 Red Pushbutton 178030-007 Yellow Pushbutton, 179125-001 Grounding Clip (Acceptable substitute is part no. 179074-010)

4-7

Page 44

Illustrated Parts Lists Major Havoe

178116-005 —F Drive Stud 039422-01 176010-106 Sere Upper Frame

I

033426-02 | Roller | 035938-01 ‘ Encoding Wheel

739002-001

039424-01 Drive Shaft

035937-01 Ball Bearing

039425-01 Idler Shaft

039423-01 Lower Frame

179173-001 Lamp Socket Optical Coupler

A035220-02 Coupler PCB Assy

79-5835 +—— Connector

75-0448 7 Split-Lock Washer

72-8406 Screw

Flat Washer

70-1H161 Lamp

Figure 4-3 Roller-Control Assembly A039421-02 A

Page 45

Major Havoc

Roller-Control Assembly Illustrated Parts Lists

Parts List

Part No. Description

A035220-02 Coupler PCB Assembly—includes 79-58356 4-Position Connector 035221-01 Printed-Circuit Board 110000-151 1500, +5%, % W Resistor (not shown) 139002-001 Radial Optical Coupler

70-1HI61 14 V Wedge-Base Lamp 72-8406 #4-4) x 4-Inch Hex Socket-Head Cap Screw 75-0148 #4 Plain Flat Washer 75-0445 #4 Spring Split-Lock Washer

035937-01 Ball Bearing—4 per assembly 035938-01 Etched Encoding Wheel 039422-01 Upper Frame 039423-01 Lower Frame

039424-01 Drive Shaft 039425-01 Idler Shaft 039426-02 Blue Translucent Roller 176010-106 #8 x 3%-Inch Cross-Recessed Zinc-Plated Steel Pan-Head Screw

178116-005 #6 x 0.31-Inch Drive Stud 179173-001 Wedge-Base Lamp Socket

Page 46

Illustrated Parts Lists Major Havoc

A041342-01 70-304 Fluorescent Tube 99-11009 Speake Harness Assy Socket 041252-01 179035-001 a Grille/Bracket Tube Holder palostSniekd 179035-001 99-11006

A005493-01 Harness Assy 99-11003 Ste

Grounding Clip

148004-002 Speaker 037469-01 Bracket

79-561816P osizato2 — Wire Nut Panel 142028-001 Transformer Wire Colors for Speaker

NOTE Brown To make sure that the fluorescent Orange tube starts, check that the ground wireis firmly attachedto both the ballast transformer and steel tube bracket,

Figure 4-4 Fluorescent Light and Speaker Board Assembly A041320-01 A Parts List

Part No. Description

A005493-01 Fluorescent Tube Harness Assembly A037540-01 Ground Wire with Ring Lug (not shown) A041342-01 Speaker Harness Assembly 70-304 18-Inch, 15 W, Cool White Fluorescent Tube 79-561816P Spring-Connector Wire Nut for 16- to 18- Gauge Wires 99-11003 Fluorescent Tube Starter 99-11006 Fluorescent Tube Locking Tab (consists of two pieces) 99-11009 Starter Socket

037469-01 ‘Tube Bracket 04124102 ‘Wood Mounting Panel 041252-01 Speaker Mounting Grille/Bracket 041325-01 Ballast Shield

142028-001 60 Hz, 118 V, Ballast Transformer 148004-002 5-Inch Diameter, 5 W, 4-Ohm Shielded Speaker 179035-001 ‘Tube Holder 179125-001 Grounding Clip (Acceptable substitute is part no. 179074-010)

Page 47

Major Havoc Illustrated Parts Lists

A039254-01 Harness Assembly

Before removing or repairing the util ty panel, turn the game off. Players may receivean electrical shock if the utility panel is not properly grounded! After servicing any parts on the panel, make sure that the ground wireis firmly altachedio the bracket

A002465-01 Coin Counter

176018-002 Screw

69-001 SelfTest Switch 75-9910W0 Stamped Nut 119006-103 040412-01 Volume Control Bracket

62-041 Auxiliary Coin Switch

Figure 4-5 Utility Panel Assembly A040413-01 B Parts List

Part No. Description

A002465-01 Coin Counter A039254-01 Volume Control Harness Assembly (includes grounding clip) 62-041 SPDT Pushbutton Auxiliary Coin Switch with Black Cap 69-001 DPDT Selffest Switch

040412-01 Component Panel 75-9910WO 1%2-32 Stamped Nut 119006-103, Dual Volume Control 176018-002 #6-32 x ¥2-Inch Thread Forming Machine Screw

Page 48

Illustrated Parts Lists Major Havoc

99-10140 Panel Assembly 75-9488 Locknut a QS J 99-10116 Ss 6 Lever 99-10152 DWARAR Right Coin Inlet 99-10147 Harness 171006-035 Coin Mechanism

75-9448 ON Locknut \\ 99-10096 \\ Fasiener C\ 99-10151 a Left Coin inlet Ny 70-11-47 a Lamp N 99-10080 N Lamp Socket i

(j 99-10105 72-9406S [ Bar Screw aN Qs ]

99-1104 Bar Retainer

a7

a 99-10042 thru 99-10045 99-10154 Coin Switch Assembly. Bracket Assembly

99-10153 Coin Return Box 99-10150 Switch Cover 99-10068 Coin Chute 65-4416 Coin Switch

99-10075 thru 99-10078 Switch Wires 99-10008 Retainer 7514128 Screw

Figure 4-6 Coinco Coin Door Assembly 171027-001 A

4-12

Page 49

Major Havoc

72-HA1404C Screw

99-10139 Coin Door

a

99-10148 Lock Assembly

99-10145

g®

72-JA1405B

038091-01 Coin Box

Figure 4-6 Coinco Coin Door Assembly, continued 171027-001 A Mlustrated Parts Lists

99-10142 Button Housing

99-10134 99-10119 Cover j~—————_ Button Assembly 99-10118 Button

99-10115 Spring

99-10141 Coin Return Cover

99-10117 Coin Return Door

Ix—— _99-10144 Channel Clip SQ 99-15066 Screw

99-10149 Service Door

99-10143 Frame

4-13

Page 50

IWustrated Parts Lists Major Havoc

Coinco Coin Door Assembly Parts List

Part No. Description 171006-035 Metal Coin Mechanism for U.S. $.25 65-441C Coin Switch 70-11-47 Miniature Bayonet Lamp 72-94068 #4-40 x Z-Inch Truss-Head Screw 72-HAI404C #4-40 x %4-Inch Pan-Head Screw 72-JA1405B #4-40 x .31-Inch Pan-Head Screw 75-14128 #4-40 x 3%4-Inch Pan-Head Screw 75-9945, #4-40 Lock Nut 99-10008 Retainer 99-10042 Coin Switch Assembly for Belgium 5 Fr and U.S. $.25 99-10043, Coin Switch Assembly for German 1 DM, Japanese 100 Yen, Swiss 1 Fr 99-10044 Coin Switch Assembly for German 2 DM, Italian 109 L, U.S. $1.00 99-10045 Coin Switch Assembly for Australian $.20, German 5 DM, British 10 P 99-10068 Coin Return Chute

99-10075Switch Wire(included in coin switch assembly 99-10043)
99-10076Switch Wire(included in coin switch assembly 99-10042)
9910077Switch Wire(included in coin switch assembly 99-10044)
99-10078Switch Wire(included in coin switch assembly 99-10045)

99-10080 Lamp Socket 99-10081 Key Holder 99-10096, Fastener 99-10104 Bar Retainer 99-10105 Bar 99-1015 Spring 99-10116 Plastic Coin Return Lever 99-1017 Steel Coin Return Door 99-1018 Amber Coin Return Button 99-10119 Amber Coin Button for US. $.25 99-10134 Coin Button Cover 99-10139 Coin Door 99-10140 Coin Door inner-Panel Assembly 9940141 Diecast Coin Return Cover 99-10142 Diecast Button Housing 99-10143 Coin Door Frame 99-10148 Lock Assembly 99-10149 Setvice Door 99-10150 Switch Cover 99-10151 Left Coin inlet 99-10152 Right Coin Inlet 99-10153, Coin Return Box 9910154 Bracket Assernbly 99-15066 Screw for Clamp

Page 51

Major Havoc Ulustrated Parts Lists

170000-001 99-15026

Lamp Coin Inlet

179047-001 Lamp Base 99-15023 Base Plate

99-15056 Screw for Bezel rew for Bezel 99-15040 Lever

99-15025 Coin Inlet

. + 28:15054 Pivot for Lever

99-15055 oe Retaining Screw Za

75-914S Hex Nut

Coin Return Box Lock Wash.

99-15056 99-15027 Screw for Bezel Coin Return Box

99-15075, Sw. Adjuster

99-15029 Bracket _~ 99-15060 ‘Sw. Cover 99-15042 Switch

75-3414S, Screw

72-1414, Screw

Figure 4-7 Coin Acceptor Coin Door Assembly 171034-xxx A

4-15

Page 52

Ilustrated Parts Lists Major Havoc

99-15052 Spring for Button 99-15038 Bezel for Button

99-15001 thru 99-15011 Return Button

A037542-01 Harness—not shown

99-15039 Bezel for Cover

| —____ 99-15036 : Cover 9915067 Lock Assy.

038091-01 : 3 ~ Coin Box > RK y

99-15073 Upper Door 99-15074 99-15070 Lower Door

99-15072 Door Frame

171034-001 — U.S. 25¢/25¢ Coin Door 171034-003 — Canadian 25¢/25¢ Coin Door 171034-005 — U.K. 10 P/50 P Coin Door 171034-006 — U.K. 20 P/50 P Coin Door 171034-009 — German 2 DM/1 DM Coin Door 171034-010 — German 2 DM/S DM Coin Door 171034-011 — German 1 DM/5 DM Coin Door 171034-015 — French 2 Fr/1 Fr Coin Door

Figure 4-7 Coin Acceptor Coin Door Assembly, continued 171034-xxx A

Page 53

Major Havoc ilustrated Parts Lists

Coin Acceptor Coin Door Assembly Parts List

Part No. Description A036597-01 Harness Assembly (Ireland-Built cabinet only) A037542-01 Harness Assembly 7214148 #4-40 x %-Inch Cross-Recessed Pan-Head Steel Machine Screw 75-056 #6 Internal Tooth Zinc-Plated Steel Lock Washer 75-9148 #4-40 Steel Machine Hex Nut 75-3414 #4-40 x J-Inch 82° Cross-Recessed Flat-Head Steel Machine Screw 99-15001 Coin Return Button with U.S, 25-cent Price Plate 99-15002 Coin Return Button with U.S. $1 Price Plate 99-15003 Coin Return Button with German 1 DM Price Plate 99-15004 Coin Return Buiton with German 2 DM Price Plate 99-15005 Coin Return Button with German 5 DM Price Plate 99-15006 Coin Return Button with Belgian 5 Fr Price Plate 99-15007 Coin Return Button with French i Fr Price Plate 99-15008 Coin Return Button with Japanese 100 Yen Price Plate 99-15009 Coin Return Button with British 10 Pence Price Plate 99-15010 Coin Return Button with Australian 20-cent Price Plate

99-1501 Coin Return Button with Italian 100 Lire Price Plate 99-15025. Left Half of Coin Inlet 99-15026 Right Half of Coin Inlet 99-15027 Side Plate of Coin Return Box 99-15028 Base Plate of Coin Return Box 99-15029 Switch Bracket 99-15036 Metal Coin Return Cover 99-15038 Bezel for Coin Return Button 99-15039 Metal Bezel for Coin Return Buiton 99-15042 Coin Switch for U.S. 25 cents 99-15052 Spring for Coin Return Button 99-15055 Retaining Screw 99-15056 #4-40 x Y¥o-Inch Cross-Recessed Pan-Head Steel Machine Screw 99-15060 Switch Cover 99-15063, Screw for Hinge 99-15066 Screw for Clamp 99-15067 Lock Assembly 99-15070 Doors and Frame 99-15071 Clamp for Frame 9915072 Door Frame 99-15073 Upper Door 9915074 Lower Door 99-15075, Switch Adjuster 99-15083 Base Plate—includes: 99-15040 Lever 9915054 Pivot for Lever 038091-01 Coin Box—not included in assembly (Acceptable substitute is part no, A037491-0)) 170000-001 63 V Miniature Wedge-Base Incandescent Lamp 171006-035 Metal Coin Mechanism 171050-001 Dual Entry Face Plate 179047-001 Lamp Base

Page 54

Illustrated Parts Lists Major Havoc

A037395-01 Transformer Assembly -—#&—— WARNING—A.— Fuse block cover must be in place during game operation

A021084-02 Voltage Plug 29-053 Capacitor

034544-01 Fuse Cover

79-4411001 7e-705018¢ Fuse Post Capacitor Bracket 1 mK 46-2017002 Fuse

A035891-02 Fuse Harness 034482-02

Chassis

037639-01 Label

. A034630-01 ruse Boek Filter Assembly

P| 46-2014002 , Fuses SS 79-15021001 x Terminal Block \ Cag A035890-01 Power Harness

3A-MDA3501 A034629-01 Rectifier AC Harness

Figure 4-8 Power Supply Assembly A037396-04 F

4-18

Page 55

Major Havoc Illustrated Parts Lists

Power Supply Assembly Parts List

DesignatorDescriptionPart No.
a27,000 wF, 15 VDC Electrolytic Capacitor29.053
cl2-Inch Diameter Capacitor Mounting Bracket78-70501SC
CRI‘Type-MDA 3501 Bridge Rectifier3AMDA3501
FlPanel-Mounting Non-Indicating 3AG Cartridge‘Type Fuse Post79-4411001
FL7 A, 250 V, 3AG Slow-Blow Glass Cartridge-‘Type Fuse46-2017002
FLLabel for Fuse Value037639-01
F24 A, 250 V, 3AG Slow-Blow Giass Cartridge“lype Fuse(Acceptable substitute is46-2014002

part no. 46-2014001)

FB20 A, 32 V, AG Slow-Blow Glass Cartridge‘Iype Fuse46301203
F4-F6,4 A, 250 V, 3AG Slow-Biow Glass Cartridge‘Type Fuse(Acceptable substitute is46-2014002

part no. 46-2014001)

F2-F65-Position 3AG Fuse Block with %-Inch Quick-Disconnect Terminals79-3206
F2-F6Fuse Harness AssemblyA035891-02
F2-F6Fuse Block Cover034544-01
F2-F6Label for Fuse Values037641-01
F42-Circuit Single-Row Terminal Block(located under F4)79-15021001
FLIRFI Filter Assembly (designation not marked)A034630-01
J2Power Harness AssemblyA035890-01
BVoltage Plug for 120 V (105-135 VAC)(yellow wire color)A021084-02
J4aAC Harness AssemblyA034629-01
TlTransformer Assembly(designation covered)A037395-01

Nylon Type 6/6 Hole Bushing with %-Inch Inside Diameter x 55/64-Inch Outside 78-2708 Diameter x 4 -Inch Thick Power Supply Chassis Base 034482-02

4.19

Page 56

Illustrated Parts Lists

178149-607 Nylon Standoff = 7946045 Screw

039586-01 High-Voltage Shield

A201012-01 HighVottage PCB

A035435-04 Regulator/Audio i PCB See Figure 410

175004-708 Washer

176015-112 Screw Major Havoc

176015-112 ‘Screw

039585-01

A201024-01 Defiection PCB

034536-03 Foam Pad 176015-112 Screw

175004-708 Washer

a »

1034536-02 Foam Pad

A041347-21 Major Havoc Game PCB See Figure 4-11

S

Figure 4-9 PCB Mounting Hardware

4-20

Page 57

Major Havoc Ulustrated Parts Lists

PCB Mounting Hardware Parts List

Part No. Description

A035435-04 Regulator/Audio II PCB A201012-01 High-Voltage PCB A201014-01 Deflection PCB 72-1604S #6-32 x Y%4-Inch Cross-Recessed Pan-Head Screw

034536-02 9.50-Inch Thick Foam Pad (located between Game PCB and cabinet wall; between Regulator/Audio PCB and cabinet wall) 034536-03 1.12Inch Thick Foam Pad (located between Deflection PCB and cabinet wall) 039585-01 High-Voltage Cage 039586-01 High-Voltage Shield

175004-708 #8 Flat Fiber Washer 176015-112 #10 x 34-Inch Cross-Recessed Pan-Head Screw 178149-607 Nylon Standoff

4-21

Page 58

Mlustrated Parts Lists Major Havoc

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the Specific written permission of Ataf, Inc., Sunnyvale, CA. This drawing is on'y conditionally issued, and neither receipt nor possession thereof confers or transfers any right in, or license to use, the subject matter of the draw- ” ing or ay design or technical information shown thereon, c nor any right to reproduce this drawing or any part there: 4 of. Except for manufacture by vendors of Atari, Inc., and for manufacture under the corporation's written license, no right to reproduce this drawing Is granted or the subject Matter thereat unless by written agreement with or o ‘written permission from the corporation. C20

—+ i—

C18

  • 3300. +f-— 35V i

5.6K

Pa ae Oo fo} ) ]R24,., 7Wh- Oo z a ——— A

Tip 32 TOAZ 002A TDAZCO2A | are jo IN Pcie calls csc Re20g) cla 220 | R21, i/2w cia 4b a7o_* TSTR20 qGoci R19

ClO 3BS0QuF +bL— 35V R30 R91/2W CD cr: oF inscoz 2 ” 3500.F UTR —+ yur A 9g] 35V

Figure 4-10 Regulator/Audio II PCB Assembly A035435-04 F

Page 59

Major Havoc Illustrated Parts Lists

Regulator/Audio II PCB Assembly Parts List

DesignatorDescriptionPart No.

Capacitors

cl470 uF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-250477
C20,001 #F, 50 V, Ceramic-Disc Axial-Lead Capacitor122002-102
C30.1 pE, +80%, -20%, 50 V, Ceramic-Disc Capacitor122002-104
C4470 uF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-250477
cs.0.01 wE, 25 V Minimum, Ceramic-Disc Axial-Lead Capacitor(Acceptable100015-103,

substitute is part no. 122005-103)

C60.22 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor122004-224
c70.001 pF, 50 V, Ceramic-Disc Axial-Lead Capacitor122002-102
C80.22 pF, 25 V, Ceramic-Disc Axial-Lead Capacitor122004-224
C9, C103300 uF, 35 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-350338
a0.1 pE, +80%, -20%, 50 V, Ceramic-Disc Capacitor122002-104
C12470 pF 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-250477
C13,1000 pF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-250108
cl40.01 wE, 25 V Minimum, Ceramic-Disc Axial-Lead Capacitor(Acceptable100015-103

substitute is part no. 122005-103)

C15,0.22 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor122004-224
C160.001 #E 50 V, Ceramic-Disc Axial-Lead Capacitor122002-102
cl70.22 uF 25 V, Ceramic-Disc Axial-Lead Capacitor122004-224
C18, C193300 pk, 35 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-350338
€20, C210.1 uF, +80%, -20%, 50 V, Ceramic-Disc Capacitor122002-104

Diodes

CRI‘Type-IN4002, 1 A, 100 V Silicon Rectifier Diode31-IN4002
CR4Type-IN4002, 1 A, 100 V Silicon Rectifier Diode31-IN4002
CRS-CR8Type-1N5401, 3 A, 100 V Silicon Rectifier Diode311N5401

Integrated Circuits

QlType-LM305, 5 V, Linear Voltage Regulator37-LM305
Q5TypeTDA2002A, 8 W, Linear Audio Amplifier Integrated Circuit137151-002
QTTypeTDA2002A, 8 W, Linear Audio Amplifier Integrated Circuit137151-002

Resistors

RI2702, +5%, % W Resistor110000-271
R333.Q, +5%, 4 W Resistor110000-330
R41002, +5%, % W Resistor110000-101
RS2.79, 25%, 1 W Resistor110009-027
RG3.9kQ,45%, % W Resistor110000-392
R77.5 kQ, +5%, % W Resistor110000-752

R8 1 kQ Vertical PCB-Mounting Cermet Potentiometer (Acceptable substitute is part no. 19-315102) 119002-102

RO2200, +5%, Ye W Resistor110001-221
RIO1Q, 5%, % W Resistor110000-010
Ru100, 15%, % W Resistor110000-100
RI21002, +5%, % W Resistor110000-101
R13, R1410k, +5%, % W Resistor110000-103
RID10, 45%, 4 W Resistor110000-010,
R2010,5%, % W Resistor110000-100

(continued on next page)

4-23

Page 60

Mlustrated Parts Lists Major Havoc

Regulator/Audio II PCB Assembly Parts List, continued

DesignatorDescriptionPart No.
R212200, +5%, ¥ W Resistor110001-221
R221002, +5%, “4 W Resistor110000-101
R240.12, £3%, 7 W Wirewound Resistor19-100P1015
R27, R281kQ, +5%, %’ W Resistor110000-102
R29, R30100, +5%, 14 W Resistor110600-100.
R32, R335.6 kQ, +5%, 4 W Resistor110000-562

Transistors

Q2‘TypeTIP32 PNP Power Transistor33-TIP32
Q3Type-2N3055 NPN Silicon Transistor34-2N3055,

Mechanical Parts

J66-Position Connector Receptacle79-58306
79-Position Connector Receptacle79-58308
J84-Position Connector Receptacle79-58354
96-Position Connector Receptacle79-58306
yo12-Position Connector Receptacle79-58346
Q2#6-32 x \4-Inch Binder-Head Nylon Screw75-F60405,
@#6-32 Nut/Washer Assembly75-9516
Q3Thermally Conductive Silicon Insulator78-16008
Q5Thermally Conductive Silicon Insulator78-16008
Q5,Q7#6 x 3-Inch Cross-Recessed Pan-Head Zinc-Plated Steel Screw72-6065

Heat Sink 034531-01

Page 61

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 62

Illustrated Paris Lists

yout = xour, ‘319 Major Havoc

HN THU 5ges

ant °

eI = ca9 a = x08 ;

  • 2 ew SS I 7s 8

nN eee

E RATS: ert

reo} | ise [arsr___ 818 ==! \ ass mse? &

pa -—— — es

a? = = : [| ' a ° on © | \|

4-26 Figure 4- 11 Major Havoc PCB Assembly A041347-21 G

Page 63

Major Havoc Illustrated Parts Lists

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING ‘CONFIDENTIAL: Reproduction forbidden without ne specific witten permission of Alari, Inc., Sunnyvale, CA. This drawing is only conditionally issued, andi neither receiptnor possession thereot con: {ers or transfers any right in, orlicense to uss, the subjectmatter of thedrawing or any design or technical informetion shown thereon, ‘or any right to repreduce this drawing or any part thereot. Except for manufacture by vendors of Atari nc, and for manufacture under the corporaiions wilten'icense, no rights grantedio reproduce this drawing or the subject matter thereof, unless by writen agreement with or written permission trom the corporation. Figure 4-11 Major Havoc PCB Assembly, continued A041347-21 G

4-27

Page 64

iNlustrated Parts Lists

Major Havoc PCB Assembly Major Havoc

Parts List

DesignatorDescriptionPart No.

Capacitors

cl, C2100 pF, 35 V, Aluminum Electrolytic Axial-Lead Capacitor24-350107
C3, C52.2 uF, 35 V, Tantalum Capacitor122000-225
C41 uF, SOV, Aluminum Electrolytic Radial-lead Capacitor24-500105
co100 wF, 35 V, Aluminum Electrolytic Axial-Lead Capacitor24-350107
C7,C8B1 WE, 50 V, Aluminum Electrolytic Radial-Lead Capacitor24-500105
co0.1 #F, 50 V Ceramic Capacitor122002-104
clo100 pF, 100 V Minimum, Dipped, Fixed Mica Capacitor128002-101
cil39 pF, 100 V Minimum, Dipped, Fixed Mica Capacitor128002-390
cl20.01 wF, +80% -20%, Ceramic Axial-lead Capacitor122005-103,
Ci3-C180.1 wF, 50 V Ceramic Capacitor122002-104
cas100 pF, 100 V Minimum, Dipped, Fixed Mica Capacitor128002-101
C20"100 pF, 100 V Minimum, Dipped, Fixed Mica Capacitor128002-101
C21, C220.1 pF, 50 V Ceramic Capacitor122002-104
C230.01 wE, 100 V Polyester Radial-Lead Capacitor21-101103
C240.033 uF, +10%, 50 V Polycarb Axial-Lead Capacitor122010-333
C25, C260.1 pF, 50 V Ceramic Capacitor122002-104
02839 pE, 100 V Minimum, Dipped, Fixed Mica Capacitor128002-390
C€30~-C330.1 wE 50 V Ceramic Capacitor122002-104
C340.01 wF, 190 V Polyester Radial-Lead Capacitor21101103
C35,0.1 #E, 50 V Ceramic Capacitor122002-104
C360.033 wk, +10%, 50 V Polycarb Axial-Lead Capacitor122010-333
C370.1 #F, 50 V Ceramic Capacitor122002-104
3939 pK, 100 V Minimum, Dipped, Fixed Mica Capacitor128002-390
C4)0.1 wE, 50 V Ceramic Capacitor122002-104
C420.001 uF, 100 V Polyester Radial-Lead Capacitor21101102
C43-C480.1 wF, 50 V Ceramic Capacitor122002104
C490.01 wF, +80% -20%, Ceramic Axial-Lead Capacitor122005-103
C500.1 wF, 50 V Ceramic Capacitor122002-104
C5110 pE, 100 V Minimum, Dipped, Fixed Mica Capacitor128002-100
5239 p& 100 V Minimum, Dipped, Fixed Mica Capacitor128002-390
C53-C55150 pF, 100 V Minimum, Dipped, Fixed Mica Capacitor128002-151
C560.1 wE, 50 V Ceramic Capacitor122002-104
C57220 pF 100 V Minimum, Dipped, Fixed Mica Capacitor128002-221
C580.01 pF, +80% -20%, Ceramic Axial-Lead Capacitor122005-103
C59-C610.1 pF, 50 V Ceramic Capacitor122002-104
C62, C630.22 wR, + 20%, 25 V, Ceramic Axial-Lead Capacitor122004-224
C64, C650.001 pF, 50 V Ceramic Capacitor122002-102
C660.22 wR, +20%, 25 V, Ceramic Axial-Lead Capacitor122004-224
C670.01 pF, +80% -20%, Ceramic Axial-Lead Capacitor122005-103
C68-C700.001 uF, 50 V Ceramic Capacitor122002-102
C7I-C740.01 uF, +80% -20%, Ceramic Axial-Lead Capacitor322005-103
C75-C810.1 zE, 50 V Ceramic Capacitor122002-104
C820.01 ¢F, +80% -20%, Ceramic Axial-Lead Capacitor122005-103
C830.1 wE, 50 V Ceramic Capacitor122007104

4-28 (continued on next page)

Page 65

Majot Havoc

Major Havoc PCB Assembly Illustrated Parts Lists

Parts List, continued

DesignatorDescriptionPart No.
C84, C850.01 uF, + 80% -20%, Ceramic Axial-Lead Capacitor122005-103
C86-C88470 uF, 100 V Ceramic Capacitor122016-471
C89-COL0.1 wF, 50 V Ceramic Capacitor122002-104
C92, C93,0.01 EF, + 80% -20%, Ceramic Axial-Lead Capacitor122005103,
coh0.1 E50 V Ceramic Capacitor122002-104
€100-C175,0.1 zF, 50 V Ceramic Capacitor122002-104
C178, C179.0.1 wE, 50 V Ceramic Capacitor122002-104
C182-C1890.1 wE, 50 V Ceramic Capacitor122002-104
C190-C2050.1 pF, 50 V Ceramic Capacitor122002-104

Colls

Li, L2100 wH, +10% Inductor141002-001
13-17830 mA, 0.290, +10%, 1.0 wH Peaking Coil Inductor141007001

Diodes

CRIType-MV5053 Red Light-Emitting Diode38-MV5053
CR2-CR5Type-1N100 20 ma, 80 V Diode31-INi00
CRG, CR7‘Type-IN914 10 mA, 100 V Switching Diode31HINO}4
CR8‘Type-1N100 20 mA, 80 V Diode31-IN100

Integrated Circuits

1AStatic RAM Integrated Circuit(Acceptable substitutes are part numbers137198-001

137211001 and 120)

WKStatic RAM Integrated Circuit(Acceptable substitutes are part numbers137198-001

137211-001 and -120)

IL‘Type-27128 EPROM (200 ns) Integrated Circuit136025-104
MIN‘Type-27128 EPROM (200 ns) Integrated Circuit136025-103
AN/P‘Type-27128 EPROM (200 ns) Integraied Circuit(Acceptable substitute is part136025-102

number 136025-109)

1Q‘Type-27128 EPROM (200 ns) integrated Circuit136025-101
IRType-74L8245 Integrated Circuit37-7ALS245,
2DType-74LS32 Integrated Circuit37-74L832
aL‘Type-741804 Integrated Circuit37-74L504
2MType-74LS253 Integrated Circuit37-74L8253,
2N‘Type-74LS74 Integrated Circuit37-TALS74
2P‘Type-741S244 Integrated CircuitB7-7418244
2QType-7418244 Integrated Circuit37-74L8244
25Type-6502B Integrated Circuit90-6012
3A, 4AType-74802 Integrated Circuit37-74802
3B‘Type-74LS191 Integrated Circuit37-74LS191
3c‘Type-74LSI75 Integrated Circuit37-74LSI75
3D‘Type-74804 Integrated Circuit37-74804
3EType-74874 Integrated Circuit3774874
3F‘Type-74L874 Integrated Circuit37-7ALS74
3HType-74S32 Integrated Circuit37-74832
3)‘Type-74S10 Integrated'Circuit137236-001
3KType-741S157 Integrated Circuit37-7ALS157
3L‘Type-74L832 Integrated Circuit3 7-7ALS32
3M‘Type-741S74 Integrated Circuit37-ALST4
3N‘Type-74L808 Integrated Circuit37-741S08

(continued on next page)

Page 66

Ujustrated Parts Lists Major Havoc

Major Havoc PCB Assembly Parts List, continued

DesignatorDescription.Part No.
3P‘Type-74874 Integrated Circuit37-4874
3Q‘Type-74LS163 Integrated Circuit137274-001
3RType-7415245 Integrated Circuit37-7T4LS245,
3S,Type-74808 Integrated Circuit37-74S08
4B‘Type-748260 integrated Circuit37748260
4EType-741S163 Integrated Circuit137274-001
4FType-741802 Integrated Circuit37-74LS02
4HType-74109 Integrated Circuit37-74109
4g‘Type-741S163 Integrated Circuit137274-001
4KType-7415163 Integrated Circuit137274-001
4LType-74LS139 Integrated Circuit377418139
4M‘Type-74LS32 Integrated Circuit37-74LS32
4NType-7418139 Integrated Circuit37-TALSI39
4P‘Type-74LS04 Integrated Circuit37-74LS04
4Q‘Type-748393 Integrated Circuit37-74L5393,
4R‘Type-741S161 Integrated Circuit37-741S161
4SType-74S393 Integrated Circuit37-7418393
SAType-74S74 Integrated Circuit37-74S74
5B‘Type-74LS174 Integrated Circuit37-74LS174
5CType-741827 Integrated Circuit37-74L827
5D‘Type-74L874 Integrated Circuit37-TALS74
5E‘Type-741532 Integrated Circuit37-74LS32
SF‘Type-74LS157 Integrated Circuit37-74LS157
SH‘Type-741S157 Integrated Circuit37-74LS8157
5J‘Type-741S164 Iniegrated Circuit37- 7418164
SK‘Type-74LS08 Integrated Circuit37-74LS08
SL‘Type-74LSI57 Integrated Circuit37-74LS157
5M‘Type-741S245 Integrated Circuit377418245
5N‘Type-74LS138 Integrated Circuit13 7177-001
5PType-74LS00 Integrated Circuit37-74LS00
5Q‘Type-74LS161 Integrated Circuit37-74LS161
5RType-74LS244 Integrated Circuit37-74LS244
6AType-74S86 Integrated Circuit137002-001
6BType-74LS157 Integrated Circuit37-74LS157
6c‘Type-828129 integrated Circuit136002-125
6DType-74LS157 Integrated Circuit37-74LS157
OE‘Type-741S157 Integrated Circuit37-74LS157
oH‘Type-27128 EPROM (300 ns) Integrated Circuit136025-106
GK‘Type-27128 EPROM (300 ans) Integrated Circuit136025107
6KIL‘Fype-2764 EPROM Integrated Circuit(Acceptable substitute is part number136025-105

136025-010)

6LMStatic RAM Integrated Circuit(Acceptable substitutes are part numbers137198-001

137211-001 and -120)

6M/NStatic RAM Integrated Circuit(Acceptable substitutes are part numbers137198-001

137211-001 and -120)

6N/P‘Type-74L808 Integrated Circuit37-74LS08
6PIQType-745374 Integrated Circuit37-741 8374

4-30 (continued on next page)

Page 67

Major Havoc illustrated Parts Lists

Major Havoc PCB Assembly Parts List, continued

DesignatorDescriptionPart No.
6QR‘Type-748374 Integrated Circuit37-TALS374
7A‘Type-74LS32 Integrated Circuit37-74LS32
7BType-74S00 Integrated Circuit37-74800
7cType-7415138 Integrated Circuit137177001
7DType-74LS04 Integrated Circuit37-7ALSO4
JE‘Type-74LS175 Integrated Circuit37-7TALSI7S,
TE/FType-74LS279 Integrated Circuit137179-001
7HType-74LSI75 Integrated Circuit37-7ALSI75S
vAType-74LSII Integrated Circuit137149-001
TKType-74LS163 Integrated Circuit137274-001
7LType-74LS20 Integrated Circuit37-7ALS20
™Type-74LS163 Integrated Circuit137274-001
1NType-74LS10 Integrated Circuit37-7A1S10
7QType-74LS74 Integrated Circuit37-7ALS7A
7RType-7418244 Integrated Circuit37-7418244
8A‘Type-74LS194 Integrated Circuit37-7ALSI94
8B‘Type-74LS194 Integrated Circuit37-7ALSIO4
8cType-74LS194 integrated Circuit37-74LS194
8DType-74LS194 Integrated Circuit37-74LS194
8EType-74LS194 Integrated Circuit37-7ALS194
8FType-74LSI94 Integrated Circuit37-7ALSIO4
8HType-74LS157 Integrated Circuit37-74LS157
8)Type-74LS02 Integrated Circuit37-74LS02
8kType-74LS00 Integrated Circuit37-74LS00
BLType-74L800 Integrated Circuit37-74LS00
8MType-74LS273 Integrated Circuit37-TALS273
8NType-74LS04 Integrated Circuit37-TALSO4
8PType-6502A Integrated Circuit90-6013,
8Q‘Type-74LS32 Integrated Circuit37-74L832
8RType-74iS139 Integrated Circuit37-TALSI39
oN‘Type-74LS86 Integrated Circuit37-T4LS86
9BType-74LS86 Integrated Circuit37-7ALSB6
9CType-74LS86 Integrated Circuit37-7ALS86
9cIDType-74LS273 Integrated Circuit37-7ALS273
OFMType-74LS175 Integrated Circuit37-TALSI75
aType-74LS04 Integrated Circuit37-74L804
9KType-LM319 Integrated Circuit37-LM319
OLType-74CO4 Integrated Circuit137309-001
9PIQStatic RAM Integrated Circuit(Acceptable substitutes are part numbers137198-001

137211-001 and -120)

9QIR‘Type-2804 EPROM Integrated Circuit(Acceptable substitute is part number137329-450

137329-300)

9sType-27128 EPROM (300 ns) Integrated Circuit136025-108
10HType-741820 Integrated Circuit37-741820
103Type-741S174 Integrated Circuit37 7ALSI74
10KType-74LS74 Integrated Circuit37-7ALS74
10LType-74LS174 Integrated Circuit37-7ALSI74
10MType-74LS244 Integrated Circuit37-7ALS244

(continued on next page)

4-31

Page 68

Mlustrated Parts Lists Major Havoc

Major Havoc PCB Assembly Parts List, continued

DesignatorDescriptionPart No.
mc‘Type-74LS174 Integrated Circuit37-74LS174
112N‘Type-74198 Integrated Circuit137350-001
NABIntegrated Circuit137158-002
ucIntegrated Circuit137159-001
DpIntegrated Circuit137158-002
iyType-74LS153 Integrated Circuit37-74LSIS3
nk‘Type-74LS153 Integrated Circuit37-7ALS153
MLType-741830 Integrated Circuit37-74L$30
11QType-74LS139 Integrated Circuit37-74LS139
UR, 12RType-74LS74 Integrated Ciccuit37-7ALSTA
12A/BIntegrated Circuit137352-001
12¢‘TypeTL082 Integrated Circuit37TLO82CP
12DIntegrated Circuit137352-001
12)Type-82525 Static RAM Integrated Circuit90-7005
12KType-82825 Static RAM Integrated Circuit90-7005
12N‘Trackball Interface (LETA) Integrated Circuit137304-1001
12PType-7418245 Integrated Circuit377418245
12QType-74LS245 Integrated Circuit37-74LS245
ByType-74LS174 Integrated Circuit37-TALSITA
BK‘Type-7407 Integrated Circuit37-7407
1BN‘Type-7418257 Integrated Circuit37-74LS257
13QCustom Integrated Circuit137324-1121
14BTypeT'LO84 Integrated Circuit37347
14D‘Type TLOsé Integrated Circuit37347
14Q‘Type-LM324 Integrated Circuit37-LM324
14R/5‘Type-LM324 Integrated Circuit37-LM324
VRiType-7815 Integrated Circuit37-7815
vR2‘Type-7915 Integrated Circuit377915
VR3‘Type-7805 Integrated Circuit37-7805

Resistors

RI1500, +5%, 4 W Resistor110000-151
R2, R310 kQ, +5%, & W Resistor110000-103
R42200, +5%, 4 W Resistor110000-221
RS10k, +5%, 4 W Resistor110000-103
RO. R71kQ, +5%, %4 W Resistor110000-102
R8-R134700, 45%, %& W Resistor110000-471
RI4-R191kQ, +5%, 4 W Resistor110000-102
R205.6 kQ, +5%, %& W Resistor110000-562
R2110 KO, 5%, 4 W Resistor110000-103,
R22-R241kQ, +5%, % W Resistor119000-102
R25, R2610kQ, 5%, 4 W Resistor110000-103
R272202, £5%, 4 W Resistor110000-221
R281kQ, +5%, & W Resistor110090-102
R29, R308209, £5%, % W Resistor110000-821
R31, R327.5 KO, +1%, % W Resistor0003-752
R3410 k® Horizontal Trimming Potentiometer119002-103

(continued on next page)

Page 69

Major Havoc Mlustrated Parts Lists

Major Havoc PCB Assembly Parts List, continued

DesignatorDescriptionPart No.
R3510kQ, 45%, 4% W Resistor110000-103
R382 kQ Horizontal Trimming Potentiometer119002-202
R43,1000, +5%, 4 W Resistor110000-101
R44, R458200, 15%, 4 W Resistor110000-821
R46, R4775 kQ, +1%, % W Resistor110003-752
R4810 kQ Horizontal Trimming Potentiometer119002-103,
R4910k, +5%, % W Resistor110090-103
RS5O2 kQ Horizontal Trimming Potentiometer119002-202
R5110k, 45%, % W Resistor110090-103
R52150 kQ, +5%, 14 W Resistor110000-154
R53,2.7k@, +5%, 4 W Resistor110000-272
R542.5 mA, 8 V Varistor110004-001
RSS.10 kQ Horizontal Trimming Potentiometer119002-103
R581002, 45%, % W Resistor110000-101
R592.2kQ, 45%, 4 W Resistor110000-222
R6O470 kQ, +5%, 4 W Resistor110000-474
ROL1kQ, £5%, 4 W Resistor110000-102
ROZ2.2 kQ, 45%, 4 W Resistor110000-222
R63, R6475kQ, +1%, % W Resistor110003-752
ROS3.9kO, +5%, 4 W Resistor110000-392
ROG15 kQ, +5%, 4 W Resistor110000-153
RO?1kQ, 45%, 4 W Resistor110000-102
RGB10kQ, 45%, 4 W Resistor110000-103
R695602, +5%, % W Resistor110000-561
R70-R7275kQ, 41%, % W Resistor110003-752
RI6.19 kQ, 45%, % W Resistor110000-622
RY7.5 kQ, 41%, % W Resistor410003-752
R75,619 KO, 45%, % W Resisior110000-622
R76100.0, +5%, 4 W Resistor110000-101
R77130kQ, 41%, 4 W Resistor110003-132
RIS1009, 45%, % W Resistor110000-101
R791.30 kQ, +1%, 4 W Resistor0003-132
R&O, R81200 Q Horizontal Trimming Potentiometer119002-201
R82-R89100k, +5%, 4% W Resistor110000-104
ROO.1.2kQ, 45%, 4% W Resistor116000-122
ROL2.2kQ, +5%, % W Resistor110000-222,
ROZ47kQ, £5%, Ye W Resistor110000-472
ROB10 kQ, 45%, A W Resistor110000-103
ROE3.9kQ, +5%, 4% W Resistor110000-392
ROS2,2kQ, +5%, % W Resistor110000-222
RIG22 kQ, +5%, 4 W Resistor110000-223,
ROT680, +5%, % W Resistor110000-680
RO8-R1021kQ, +5%, 4 W Resistor110000-102
R1035.6kQ, +5%, % W Resistor§10000-562
R104, RIOS1kQ, +5%, 4 W Resistor110000-102
R10622 kQ, +5%, % W Resistor0000-223

(continued on next page)

4-33

Page 70

Illustrated Parts Lists Major Havoc

Major Havoc PCB Assembly Parts List, continued

DesignatorDescriptionPart No.
R107, R1081002,£5%, % W Resistor110000-101
R1091kQ, +5%, 4 W Resistor110000-102
RIO5.6kQ, +5%, % W Resistor110000-562
RUL22 kQ, +5%, %4 W Resistor110000-223
RZ1kQ, 45%, % W Resistor110000-102
RU3, R141000, +5%, 4 W Resistor110000-101
RUS1kQ, +5%, 4 W Resistor110000-102
RIG5.6kQ, +5%, 4 W Resistor110000-562
RU722 kQ, +5%, 4 W Resistor110000-223
RUS1kQ, +5%, % W Resistor110000-102
R19, R1201009, 45%, 4 W Resistor110000-101
R121-R123,4700, +5%, “% W Resistor110000-471
R124-R1261kQ, 45%, 4 W Resistor110000-102
RI2ZERIB410 kQ, +5%, % W Resistor110000-103
R1351kQ, +5%, % W Resistor110000-102
RBO39kQ, +5%, % W Resistor110000-393,
RI3718kQ, +5%, 4 W Resistor110000-183
R1839 kQ, 5%, 4 W Resistor110000-393
R13910 kQ, +5%, 4 W Resistor110000-103
RI401kQ, +5%, % W Resistor110000-102
R4139kQ, 45%, % W Resistor110000-393
R14218 kQ, +5%, % W Resistor110000-183
R14339kQ, 25%, %& W Resistor110000-393,
R144, R145,22 kQ, +5%, %& W Resistor110000-223,
R146, R14710kQ, +5%, 4 W Resistor110000-103
R148, R149.2.2K, +5%, 4 W Resistor110000-222,
R1I50-R153,3.3kQ, +5%, & W Resistor110000-332
R154-R1571kQ, +5%, 4 W Resistor110000-102
RIS8100k, +5%, 4 W Resistor110000-104
R159, RIGO1kQ, +5%, 4 W Resistor110000-102
RI7I-RI771kQ, +5%, % W Resistor110000-102
RI78-R18510kQ, +5%, % W Resistor110000-103
RI86-R1881kQ, +5%, 4 W Resistor110000102

Sockets

1H40 Contact, Medium-Insertion-Force IC Socket79-42C24
WK40 Contact, Medium-Insertion-Force IC Socket79-42C24
IL.28 Contact, Medium-Insertion-Force IC Socket79-42C28
IM/N28 Contact, Medium-Insertion-Force IC Socket79-42C28
IN/P28 Contact, Medium-Insertion-Force IC Socket79-42C28
1Q28 Contact, Medium-Insertion-Force IC Socket79-42C28
2s24 Contact, Medium-Insertion-Force IC Socket79-42C40
6H28 Contact, Medium-Insertion-Force IC Socket79-42C28
OK28 Contact, Medium-Insertion-Force IC Socket79-42C28
6KIL28 Contact, Medium-Insertion-Force IC Socket79-42C28
6LIM40 Contact, Medium-Insertion-Force IC Socket79-42C24
6M/N40 Contact, Medium-Insertion-Force IC Socket79-42C24

(continued on next page)

Page 71

Major Havoc Mlustrated Parts Lists

Major Havoc PCB Assembly Parts List, continued

DesignatorDescriptionPart No.
TE/F24 Contact, Medium-Insertion-Force IC Socket79-42C40
8P24 Contact, Medium-Insertion-Force IC Socket79-42C40
OPIQ40 Contact, Medium-Insertion-Force IC Socket79-42C24
9QIR40 Contact, Medium-Insertion-Force IC Socket79-42C24
9S,28 Conuct, Medium-Insertion-Force IC Socket79-42C28
12N40 Contact, Medium-Insertion-Force IC Socket79-42C24
13Q24 Contact, Medium-Insertion-Force IC Socket79-42C40

Switches

SWI, SW28Toggle DIP Switch Integrated Circuit (Acceptable substitute is part160031-008

number 66-118PIT)

Transistors

4-06‘Type-2N3904 Transistor34-2N3904
O78‘Type-2N3906 Transistor34-2N3906
QoType-2N3904 Transistor34-2N3904
QioType-2N3906 Transistor34-2N3906
qu‘Type-2N3904 Transistor34-2N3904
Qi2‘Type-2N3906 Transistor34.2N3906
Qs‘Type-2N3904 Transistor34-2N3904
Qi4Type-2N3906 Transistor34-2N3906
Qs‘Type-2N3904 Transistor34-2N3904
Q16-Q18‘Type-2N6044 Transistor34-2N6044

Miscellaneous

VR2, VR32 Mil, Mica Insulator178109-001
Yl10-MHz Crystal90-123
Y28.000-MHz Crystal144002-001

‘Test Point (Acceptable substitute is part number 020670-001) 179051-002 Nylon Snap-In Fastener 81-4302

Page 72

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 73

MAJOR HAVOC 2nd printing

YOUR COMMENTS, PLEASE!

Your comments will assist Atari in improving our publications. The comments are an important part of preparing for revisions of game manuals. Please write in the space below. No postage stamp is necessary if mailed in the U.S.A.

If you have any technical questions about certain ATARI games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.

Page: Comments:

Fill in if you wish a reply:

Name ——

Firm Distributor

Address © Operator City, State Zip. — Cl Other

Area Code Phone

Page 74

First Fold

No postage necessary if mailed in the United States

BUSINESS REPLY MAIL

FIRST CLASS PERMIT NO. 173. MILPITAS, CA

POSTAGE WILL BE PAID BE ADDRESSEE

Atari Inc. Attn: Field Service/Coin-Op Division 737 Sycamore Drive P.O. Box 906 Milpitas, California 95035

Second Fold

From:

Page 75

PES BGS RON BEI BS RN BE ER 28

LSE ES SS

Warranty

Seller warrants that its printed-circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its video displays (in games supplied with displays) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment. None of the Seller's other products or parts thereof are warranted.

lf the products described in this manual fail to conform to this warranty, Sellers’ sole liability shall be, at its option, to repair, replace, or credit Buyer's account for such products which are returned to Seller during said warranty period, provided

  • Seller is promptly notified in writing upon discovery by Buyer that said products are defective:
  • Such products are returned prepaid to Sellers’ plant; and
  • Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation or improper testing

In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages.

Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms of this order, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller's part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products under this order.

The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to yourself and others. Be very cautious in using non-Atari-supplied components with our games, in order to insure your safety.

Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories. Atari cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor.

This document is and contains confidential trade secret information of Atari, Inc.

This document is loaned under confidential custody for the sole purpose of operation, maintenance or repair of Atari equipment and may not be used by or disclosed to any person for any other purpose whatever, and remains the property of Atari, Inc.

Neither it nor the information it contains may be reproduced, used, or disclosed to persons not having a need to know consistent with the purpose of the loan, without written consent of Atari, Inc. ; : : ‘ ‘ ‘ :

Page 76

C ATARI . TAR INC. a gyCAMORE pRIVE pO BOL, MILPITAS. CALIFORNIA 3" ail N9g1942:3100 * TELEX 35-7488 g5038