CATHODE RAY TOMES

Space Fury (Sega-Gremlin Monitor Mod Info)

Space Fury (revision C) (Sega, 1981) · Document · 7 pages · 2 sections · original scan

Page 1

MODIFICATION INSTRUCTIONS —_—_—_[_$_$_[—_—S—=—_——_—*

Replace the X-Y monitor with a modified monitor.

Do ECN 978 on the CPU board. See attached instructions.

Do ECN 991 on the X-Y timing board. See attached instructions.

Record the game and monitor serial numbers on the distributor record sheet. ‘

Place the colored label on the top left corner of the kick plate. . .

Each team will have the number of games the distributor has purchased. There is a good possibility that number will not be in the distributor's location. Leave the correct number to make up the difference.

The removed monitors should be loaded on your truck and returned to Gremlin with you. There will be special cases when these instructions will change.

-Provide the distributor with a copy of the Distributor Record Sheet, ~ ~~ be sure to bring the original back with you.

Page 2

rae . ° © SEK VICE NUIE SEGA/ Qremlin | EFFECT:

NUMBER: 007 . X-Y TIMING BOARD

September 17, 1981

{To ensure that the vertical and horizontal outputs of the G-80:x-Y Timing Board do Mot exceed a preset level, the addition of 2 diodes is recommended. The diodes,” type 1N914, are Installed as follows: :

  • Remove the 6-80 Timing Board from the card cage.
  • Solder the ANODE of one diode to Pin 1 of the Molex connector located on the

-front edge of the Timing Board. .it is recommended that the diode be installed : on the underside of the board. “Solder the CATHODE of the diode toa +5 volt pad on the back of the board.

~ This can be found at the +5 volt pin on the closest IC.

  • A. Install the CATHODE of the second diode to +5, in the same way. Then, solder ae the ANODE of this diode to Pin 4 of the Molex connector.

Black Band

Anode —~(———I}— Cathode

DIODE 1N914

EE SLE AE TS RAS EARLIEST OGIO EEE INE AR EEO, SEGA/Gremlin 3401 Aero Drive, San Diego, California 92123 @ Telephone 800-854. 038 :

Page 3

QUANTITY ORIGINATOR . DEPT. ‘Dare SO |¥-2r-6/ PART NUMBER \S|-002 | REASON FOR VARIANCE ’ (31-003) CECAMIC CAPACITOR ,22-uF IGV 1S WOT AVAILAALE ) 1 THE ME FRAME RERUIRED

WILL VARIANCE BE ACCEPTED ON FuTuRE Lots [_] ves D=<§\

IS ECR REQUIRED[_]yes{[_]no
‘| ECR WRITTEN BY;DATE

CHECK APPLICABLE DOCUMENTS AFFECTED BY ; VARIANCE aoe “ Oo ENGINEERING DPANINGS _ aes. Process DerarL [>4eurcuase ORDER.

[7] scazuarresLo[[] reczrvine rerorr
“|2] 20s |oo,ae{([] orser

2 - AUTHORIZATION FOR SUBSTITUTE MATERIAL

PART NUMBER7,DESCRIPTIONDATE.

= CAMCITOR | {5 t=003, ... —-- *2LME TEU CE OGL - "| sussrrzure warsrzar, USE GEE?) [WO 12-0029 .BAF 250V CEREPINC CAPR OITORS FO FEPLAOCE /E[-OO3f ON V EC¢S OF OF: : CPU Boned ASS Y BOO O107 . ; QUANTITY OF END ITEM AFFECTED

‘>| AUTHORIZED By / oepats__(9 ¢ [ S/

DATE.

Page 4

pe ENGINEERING CHANGE NOTICE

Te: 8-22- Bl EON #978 SHEET 4 OF 4 OCREF ECR #370) oT OF tT

EFFECTIVE DATE | ASSEMBLY[PART NUMBERDRAWING NUMBER[REV
"B-24-21 | CPU BOARD]800-0107B00-O1IO7.|E

CHANGE: PARTS LIST: . . = pre TEM FN gS Wis 4 1a RR WAS CUSCHSCHL.COZ. ADD -ITEM SQ. PIN gee O624 QTY C\ CAP CER *2O2UF IBV CUS

CHANGE SHEET @ ZONE TA?

o~ 1 7

is:2 CHEWAS!+ CHs

j, C2UF | IOUF I Tey 25V

REASON FOR CHANGE: OO REDJCE POWER ON DELEY FROM 15 SECS TG ZO MSECS ; DW XV MONTOL OUTRIIS ESET MSErs Ria REDUCING ‘STFESE ON MONITOR. ““QUTPUT CIRCUITS CLASS OF CHANGE - CHECK ONE ON DISTRIBUTION XA EMERGENCY. INCORPORATE IN PRODUCTION AT ONCE, ALL ASSEMBLIES, PARTS ISSUED TO ASSEMBLY AREAS ANDIX] PARTS IN STOCK AFFECTED. B URGENT. AFFECTS PARTS FOR WHICH PRODUCTION ORDERQLI DRAFTING HAVE BEEN INITIATED BUT NOT COMPLETED, PURCHASE REQUISITIONS, FINISHED PARTS IN-STOCK. PARTS ISSUED TO ASSEMBLY AREAS, AFFECTS SUB-ASSEMBLIES AND FINAL ASSEMBLIES, C AFFECTS ALL FUTURE PARTS FOR WHICH PRODUCTION ORDERS HAVE NOT YET BEEN INITIATED, BUT CHANGE ‘ NEED NOT BE CARRIED OUT UNTIL STOCK IS BALANCED. 4 D AFFECTS NO PARTS OR ASSEMBLIES-FOR NEORMA ION

wT __AND_R RECORDS ONL YeSENBEIE!mat

REQUESTED BY AND DATE:

G. HANSEN 8-22-82 MANUFACTURING

i<'] PURCHASING OUTSIDE ~ VENDOR

JDATE: UE, B02-8/

Page 5

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 6

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 7

Monitor Removal

Release the fasteners on the control panel and swing it down. Directly under the the front plexiglass, you will notice a small frame support piece. Grab it by the hand slot ‘in the middle and pull it from the game. The front plexiglass can now be removed easily by

lifting it on the bottom slightly and pulling it outward. Next,

Sosy remove the interior graphics. The graphics frame, located directly behind the interior graphics, can be removed by gripping two sides and

carefully lifting it out. Now open the the rear panel on the cabinet

and disconnect the power cable and video cable to the monitor. Now...

go back to the front and remove the four bolts in each corner of the

monitor board. Now grasp the board by the hand holds provided at a the top and bottom and pull the monitor from the cabinet. To replace --—-- -- follow -the same -procedure in reverse except you will notice. on the rear - of the new monitor there is an extra board added. Mount this board

on-the cabinet with the tie wraps provided and the connector coming

from this board is plugged into the video cable. Reconnect the power

~ . cable as usual. Before closing up, ensure that the heat sinks on the

driver transistors are not touching each other.