Jailbreak Conversion Kit Instruction Manual
Jailbreak (10125611, NSW/ACT) (Aristocrat, 2002) · Instruction Manual · 12 pages · 22 sections · original scan
x JAILBREAK CONVERSION KIT «
INSTIRGUCTIOIN MUAINCAIL
\ a"
Konami Inc. 1555 BRUMMEL AVENUE, ELK GROVE VILLAGE, IL 60007 onal is a registered ... TELEPHONE: (312) 364-6633 FAX: (312) 364-1368 TELEX: 6871385 KONAM UW trademark of Konami Industry Co., Ltd.
TABLE OF CONTENTS
Page Page
Conversion Kit Contents........ Inside Cover Wiring Harness Color Code............... 5
Introduction .......... 0... e eee e eee aes 1 Important Installation Notice ............. 6
Recommended Control Panel Layouts... ... 1 Wiring Diagram .......... 0... 7
Graphics. ............ 0.00 e ee eee eee eee 2 Technical Information .................0- 8
Monitor Specifications .................% 3 Dip Switch Setting...................0.. 9
Monitor Information................00006 4 User Information Warning........ Back Cover
CONVERSION KIT CONTENTS:
MAIN PRINTED CIRCUIT BOARD P.C.B. CAGE (FCC REQUIRED) CONNECTING WIRING HARNESS 6 SETS — BUTTON ASSEMBLIES 8-WAY JOYSTICK MARQUEE (HEADER) (1/8” acrylic sheet) ONE SET SIDE PANEL GRAPHICS (left & right) CONTROL PANEL OVERLAY CONTROL PANEL DECALS instruction decals/button decals (2 sets) MANUAL REGISTRATION CARD
REPLACEMENT ACCESSORIES ARE AVAILABLE THROUGH YOUR DISTRIBUTOR.
THIS KIT USABLE FOR COCKTAIL AND UPRIGHT VIDEO GAMES WITH A RASTAR SCAN MONITOR WHICH IS OR CAN BE MOUNTED HORIZONTALLY.
JAILBREAK INTRODUCTION
KONAMI CONVERSION KITS are the most complete conversion kits available today. Every detail has been carefully considered, designed and packaged to provide you the means of easily producing a professional conversion.
These kits have all the accessories to easily convert your UPRIGHT or COCKTAIL video game.
We strongly urge you to FULLY STUDY this instruction manual BEFORE you begin your conversion. It contains step-by-step instructions, schematic diagrams and suggestions on how to install your Konami Conversion Kit and maximize your profits. JAILBREAK can be installed in any horizontally mounted rastar scan monitor game.
Everything you will need to construct your new game is provided in this kit. All accessory parts—wiring harness, joystick, etc. are custom made for JAILBREAK by top engineers experienced in the coin-op industry. An 8-way joystick (as provided) MUST be used.
The Player Instruction and Button Control decals are made of a non-destructible acrylic material specifically to keep the player from peeling them off. Should you convert a cocktail table game, JAILBREAK is supplied with 2 sets of button decals.
SAVE YOURSELF TIME AND MONEY
The following P.C.B.’s are interchangeable with JAILBREAK P.C.B.’s Super Cobra * Scramble * Pooyan ¢ Locomotion ¢ Circus Charlie * L’il Hustler Juno First * Time Pilot * Gyruss ¢ Tutankham ¢ Turtles ¢ Super Basketball * Mega Zone Pandora’s Palace * Time Pilot '84 © Track ‘n’ Field * Hypersports « Roadfighter * Yie-Ar Kung Fu ¢ Kicker Rush ’N Attack ¢ Mikie ¢ Frogger (60% —check pin print-out) « Amidar * Roc ’N Rope « The End In other words, your JAILBREAK will plug right into existing edge connectors of the games listed above — be sure to check your pin print-out. (Keep in mind that JAILBREAK is designed as a horizontal game.)
DUAL CONTROL
By moving SW#2 of dip switch bank #3 to the “on” position, you are now in the dual control upright mode. This allows you to set up an upright game with two sets of controls rather than one set. The first set of controls should be hooked up to the 1P set of wires; the second set to the 2P wires (see wiring diagrams). Each player still challenges the “computer-controlled” opponent (alternating play). This does not allow simultaneous interaction of players on the video screen.
DUAL CONTROL LAYOUT
eset Q> &> reser
- SINGLE CONTROL LAYOUT
esust > D psn
t Bfa ale eB2e
SHOOT SELECT | SELECT SHOOT ate tT Wood BAA £94 ee £94 ee te ae SHOOT SELECT rao SHOOT SELECT
*RECOMMENDED LAYOUT
PUTTING YOUR BEST GAME FORWARD
PREPARATION: For best results, all old graphics should be removed completely from the cabinet. “Stick-on” graphics can be removed by using a hairdryer or hot air device. The heat from the dryer will loosen the adhesive, allowing you to easily pee! them off — any adhesive residue can be cleaned off with acetone and a soft dry cloth. (DO NOT USE ACETONE ON SURFACES PAINTED WITH FLAT PAINT.) TOOLS YOU NEED:
- Foaming Aerosol (such as “Windex”).
- Soft Squeegee.
- X-Acto Knife.
par PANEL DECALS
- Spray area of cabinet where Side Panel decals are to be applied with foaming aerosol or a mild soap solution. . Remove protective backing from decals. . Position decals into place. . With a soft squeegee, beginning from the center of the decal, slowly and evenly press out excess foam until you achieve a smooth finish.
- Allow to set approximately 2 to 3 hours before handling. Maximum adherence is achieved in 48 to 72 hours. pwn
- Trim side decal to fit your cabinet.
CONTROL PANEL OVERLAY:
- Refer to Recommended Contro! Panel Layout on page 1. . Drili any new holes needed. . Plug any holes that will not be used. (A permanent epoxy filler works well for this step.) . Pre-position the overlay prior to removing the backing. . Slowly apply the overlay — inch by inch on the control panei, removing the backing as you apply it. . Once it's in place, by using an X-Acto knife, cut around the button and joystick placements.
INSTRUCTION/BUTTON DECALS: Apply the Player Instruction, Button and 1 Player/ 2 Player decals in their respective positions. Apply pressure liberally. Allow to set as long as possible before putting game on location. Oo 7 RF ON
FCC WARNING LABEL: FCC Warning Labe! must be applied to the outside of the cabinet near the line cord entry.
MARQUEE
(WEAR PROTECTIVE GLASSES WHILE TRIMMING MARQUEE)
1/8” Acrylic Marquee should be cut to fit your game. DO NOT remove protective mask until this is done. One way of cutting your Marquee is as follows: (Be sure to protect painted side of Marquee from any surface which may scratch or mar finish). CUTTING WITH A KNIFE OR SCRIBER Acrylic sheet up to 3/16” thick may be cut by a method similar to that used for cutting window glass. Use a scriber of some kind — ascribing knife such as the one pictured, a metal scriber, an awl, or even a sturdy craft knife — to score the sheet. Draw the scriber several times (7 or 8 times for a 3/16” thick piece) along a straight edge held firmly in place. It is best not to remove the protective masking. Make the cuts carefully using firm, even pressure. For best results make each stroke cleanly off the edge of the sheet. Then clamp the acrylic sheet or hold it rigidly under a straight edge with the scribe mark hanging just over the edge of a table. Protect your hands with a cloth, and apply a sharp downward pressure to the other side of the sheet. It will break along the scratch. Scrape the edges to smooth any sharp corners. This method is not recommended for long breaks or thick material.
Break sheet over edge of table after scribing.
Always draw the scribing
knife along a straight edge.
P.C.B. CAGE INSTALLATION
Konami, Inc. now supplies a new style P.C.B. cage which is superior to old style cages because of ease of installation. The cage is made of a 32 point stem-stock which is fire retardant. TO INSTALL THE CAGE:
- Open cage bottom and secure to desired P.C.B. position.
- Install printed circuit board inside cage using wood screws, screwed through the cage bottom into cabinet side.
- Close the cage over printed circuit board and secure with latch on cage.
JAILBREAK: MONITOR SPECIFICATIONS
JAILBREAK requires a horizontally mounted monitor. It also generates composite negative sync. If your monitor is composite positive sync, you will have to change to composite negative sync.
- To alternate composite positive sync to composite negative sync, use 7404 IC or 74LS04 IC. The signal on the output pin from the P.C.B. is a combination of H-sync and V-sync.
FIGURE 2: +5V
FROM P.C. BOARD
NEGATIVE COMPOSITE SYNC. OUTPUT TO MONITOR (PIN 14 on P.C.B EDGE) POSITIVE COMPOSITE SYNC.
(+ 5V and GND should be taken out of the P.C. Board.)
- Separate Sync modification for JAILBREAK if your monitor has “Separate Sync” input. (For example “Electrohome brand” and Wells-Gardner brand.”) Step 1 ‘WIRING HARNESS
VIDEO SYNC
MONITOR BOARD 1o------- + - eeeene
If the picture is still not stable. . . Step 2 Prepare Hook-up wire to seperate -H and -V sync. signals.
WIRING HARNESS [[N]12] [ P f13] Eu[-v] NEGATIVE SYNC INPUT ag VIDEO SYNC
JAILBREAK: MONITOR INFO.
SERVICE INSTRUCTIONS
1.0 BLACK LEVEL CONTROL ADJUSTMENT This control has been set at the factory and should not need further attention, however, when the game is connected a slight adjustment of VR201 may be necessary to obtain the proper black level (the black portion of the picture just extinguished).
2.0 VERTICAL SIZE (HEIGHT) Location of this contro\ is shown in Fig. 1. This control must be adjusted slowly, if necessary, until the picture or test pattern attains the correct vertical proportions.
3.0 CIRCUIT PROTECTION A4,0A pigtail fuse, mounted on the Main Board has been provided to protect the Power Output Circuit.
4.0 FOCUS Adjust the focus control, located on the HV unit (1352), for maximum over-all defination and fine picture detail.
5.0 HORIZONTAL HOLD CONTROL ADJUSTMENT, VR351 (See Fig. 1) A warm-up period of at least five minutes should be allowed before alignment is carried out. With the monitor being driven from the game signal, short TP601 to TP31. Adjust VR351 until the picture stops sliding horizontally. Remove the short.
6.0 HORIZONTAL VIDEO POSITION If the video is off center on the raster some compensation can be made by adjusting this control.
7.0 VERTICAL RASTER POSITION ADJUSTMENT 'f the video is off center vertically, (short dimension of picture tube) some compensation can be made by moving the vertical raster position adjustment jumper to either positions “U” or “D”.
8.0 HORIZONTAL RASTER POSITION ADJUSTMENT If the video is off center horizontally (long dimension of the picture tube) some compensation can be made by moving the horizontal raster position adjustment jumper to either positions “R” or “L”. 9.0 HORIZONTAL WIDTH ADJUSTMENT The horizontal width coil is a hexagonal tuning tool adjustment. This control must be adjusted slowly, if necessary, until the picture or test pattern attains the correct horizontal proportions. sd
- KONAMI GAMES ARE ALL NEGATIVE COMPOSIT SYNC. USE THE THREE PIN CONNECTOR ON THE MONITOR.
19" RED 19"—~orive GRN DRIVE REO CUTOFF GRN CUTOFF’ BLU CUTOFF
*NEG H SYNC
- NEG V SYNC WHEN USING COMPOS: ITE SYNC USE HORIZ. SYNC INPUTS,
HORIZ. WIDTH COIL
HORIZ HOLD BLK LEVEL
Are
HORIZ VERT VERT VERT HORIZ CENTERING SIZE HOLD RASTER RASTER SHIFT SHIFT
FIGURE 1
JAILBREAK: WIRING HARNESS
*Cocktail Table or Dual Control Upright Only WIRE COLOR KEY: Solder Side ~———_;———_-»>__ Parts Side
(EMPTY) + 12V DC ORANGE
| ! | RED/GREEN | SPEAKER OUT | SPEAKER OUT | ORANGE/GREEN |
| \ | RED/YELLOW | *2P SHOOT | 2P SELECT* | ORANGE/YELLOW |
| BROWN/YELLOW | * 2P LEFT | 2P RIGHT* | BLUE/YELLOW | |
| VIOLETWHITE | 1P START | 2P START | VIOLET/YELLOW | |
| ORANGEMWHITE | 1P SELECT | 2P UP* | BLACK/YELLOW | |
| REDMWHITE | 1P SHOOT | SERVICE SW | ORANGE/GRAY | |
| BLUEMWHITE | 1P RIGHT | 1P LEFT | BROWN/WHITE | |
| BLACK/WHITE | 1P UP | 2P DOWN* | GRAY/YELLOW | |
| RED/GRAY | COIN 1 | COIN 2 | BLUE/GRAY | |
| GRAYMWHITE | 1P DOWN | COIN COUNTER 1 | GREEN/GRAY | |
| WHITE/PINK | (NOT USED) | COIN GOUNTER 2 | YELLOW/GRAY | |
| GREEN/BROWN | VIDEO GREEN | VIDEO BLUE | BLUE/BROWN | |
| RED/BROWN | VIDEO RED | VIDEO SYNG | WHITE/BROWN | |
| (EMPTY) | (NOT USED) | YELLOW/PINK |
BLACK GND GND BLACK BLACK GND GND BLACK
RED + 5V DG + 5VDC RED
(BASE COLOR/LINE COLOR)
IMPORTANT INSTALLATION NOTICE FOR JAILBREAK
The solid red heavy guage wires on the edge connector must be inserted at position A18 & B18, as shown in the diagram below. *Reverse condition will result in board damage!
a B18
20SxX5
N
JAILBREAK
WIRING DIAGRAM
HE NGT APPLICABLE! 2A 2A TA Tipy REGIRED POWE? CAPACITY
4512W 4512W, 4 nioWw baw BabW val
t NI same as /P CONTROLS
only for TABLE TYPE
2P SELECT
| 2P SHOOT 2P_ RIGHT 2p LEFT P_ START. JP START. 2P UP.
CONTROLS for 2P
i= SERVICE SWITCH oO
a | co 2° GAME START 1° GAME START. wu — wl 7° 0 seLecT —— — SHOOT 1P SELECT 2° DOWN.
rk RIGHT 1P SHOOT. JP _LEFT.
ouP iP RIGHT
LEFT J pown 1p UP Bi CCIN COUNTER te 1 (2v CONCOUNTE? St
Le DOWN
CONTROLS for IP
- NOTES — (DIP NOL player 2P NO.2 player
- sutge killer diodes for COIN. COUNTER instoiled on the P.C.8 *Cocktail Table or Dual Control
Upright Only BLue! GREE couor Ses MONITOR RED +12¥ 7! /8|
POWER SUPPLY Gnd + 5V(3A) +2V SPEAKE2 OUT SPEAKE® OUT 2PSELECT * 2PSHOOT *
- RGHT «© 2° Lf5T « 2° STAR? 1P START PUP 1P SELECT SERVICE 1P SHOOT ‘ iP LEFT j
iP RIGHT 2 DOWN |
IP UP COI 2 |
COIN I COIN COUNTER I 12 DOWN CON COUNTER 2 Blue GREEN SYNC RED GND GND GND GND +5V +5V EDGE CONNECTOR 5/32 INCH PITCH
JAILBREAK: TECHNICAL INFORMATION
- Required Power Capacity
+5V DC 3A or more.
+12V DC See Figure 1 below
je |e | 8 a BL + |e fee Required
Power Not Applicable
Capacity Figure 1:
- Signal output ———— Rired) analog, positive a G(green) analog, positive ——} B(blue) analog, positive qwnnrn__nr
Sync. H-V composite negative Ai 7
DIAGNOSTIC PROCEDURES
AUTOMATIC SELF-TEST — Upon “Power On”, this system will automatically test ROMS and VIDEO RAMS. The screen will display pass or fail conditions as follows:
| TEST PASSED | TEST FAILED | IF TEST FAILS |
| RAM 1 OK | RAM 1 BAD | RAM 1 = 11E |
| RAM 2 OK | RAM 2 BAD | RAM 2 |
| ROM 1 OK | ROM 1 BAD | ROM 1 |
| ROM 2 OK | ROM 2 BAD | ROM 2 |
DIP SWITCH SETTINGS
DIP SW No. 1 Settings Coin 1 Switch Set Coin 2 Switch Set
| sw | 4 | 3 | 2 | 1 | COIN] PLAY | sw | 8 | 7 | 6 | 5 | [COIN [PLAY |
| ¢ | OFF | OFF | OFF | OFF | 1 | 1 | « | OFF | OFF |OFF | OFF] | 1 | 1 | |||
| orF | on | 1 | 2 | OFF | ON | 1 | 2 | ||||
| ON | OFF] | 1 | 3 | ON | OFF] | 1 | 3 | ||
| on | on | 14 | 4 | On | on | 1 | 4 | ||||
| orF | oN | [OFF | OFF | 1 | 5 | OFF | ON | |OFF| OFF | 1 | 5 | ||
| OFF | ON | 1 | 6 | oFF| | On | 1 | 6 | |||
| ON | |OFF| | 1 | 7 | on | OFF] | 1 | 7 | |
| on | on [| 2 | 1 | on | on | 2 | 1 | ||||
| ON | OFF [OFF | OFF | 2 | 3 | ON | OFF [OFF | OFF | 2 | 3 | ||||
| OFF | ON | 2 | 5 | OFF | ON | 2 | 5 | ||||
| ON | [OFF | 3 | 1 | ON | OFF| | 3 | 1 | ||
| on | on | 3 | 2 | on | oN | 3 | 2 | ||||
| ON | ON | [OFF | OFF | 3 | 4 | on | on | |[OFF| OFF| | 3 | 4 | |
| OFF | on | 4 | 1 | OFF | ON | 4 | 1 | ||||
| ON | |OFF | 4 | 3 | ON | OFF] | 4 | 3 |
on | ON | FREE PLAY ON | ON | INVALIDITY DIP SWITCH NO. 2 SETTINGS THE NUMBER OF PLAYER'S LIFE SOUND IN ATTRACT MODE
| sw | 1 | 2 | NUMBER | sw | 8 | SOUND |
| OFF | OFF | 1 | OFF | OFF | |
| ON | OFF | 2 | : | ON | ON |
| + | [oFF| | ON | 3 | . |
| on | ON | = | SW 7 NOT USED |
CHANGE OF TABLE OR UP-RIGHT
| Sw | 3 | TYPE | DIP SWITCH NO. 3 SETTINGS |
| OFF | TABLE | Video Screen Flip | |
| « | ON | UP-RIGHT | sw_| | 1 |
| «= | |OFF | NORMAL | |
| BONUS SET | ON | UPSIDE DOWN |
sw | 4 | FIRST BONUS SECOND
| ° | OFF | 30,000 | Every 70,000 | Single/Dual Control Upright | |
| ON | 40,000 | Every 80,000 | SW | 2 | TYPE |
« [OFF | SINGLE UPRIGHT CONTROL Difficulty pfithe Game ON DUAL UPRIGHT CONTROL
| sw | 5 | 6 | DIFFICULTY | |
| OFF | OFF | EASY | |
| ON | OFF | NORMAL | “SW 3 & SW 4: NOT USED | |
| . | OFF | ON | DIFFICULT |
| ON | ON | VERY DIFFICULT |
*SHOWS NORMAL SETTING 9
USER INFORMATION
WARNING
F.C.C. REGULATION COMPLIANCE
THIS KIT IS INTENDED FOR USE ONLY ON COIN-OPERATED. VIDEO GAMES MANUFACTURED AFTER OCTOBER 1, 1983 WHICH HAVE BEEN VERIFIED FOR COMPLIANCE WITH RE- QUIREMENTS IN PART 15 OF F.C.C. RULES FOR A CLASS A COMPUTING DEVICE.
IMPROPER CONNECTION OF THIS KIT OR CONNECTION TO ANY OTHER GAME NOT SO MANUFACTURED OR VERIFIED FOR COMPLIANCE MAY CAUSE UNACCEPTABLE INTER- FERENCE TO RADIO AND T.V. RECEPTION, REQUIRING THE OPERATOR TO TAKE WHATEVER STEPS ARE NECESSARY TO CORRECT THE INTERFERENCE.
THE P.C. BOARD CAGE SUPPLIED WITH THIS CONVERSION KIT MUST BE UTILIZED AND TERMINATED TO GROUND AT THE TIME OF INSTALLATION.
Konami.
1555 BRUMMEL AVENUE, ELK GROVE VILLAGE, IL 60007 TELEPHONE: (312) 364-6633 FAX: (312) 364-1368 TELEX: 6871385 KONAM UW