Major Havoc CO-252-05 1st Encoder Documentation Supplement to TM-268 Conv Instr SD BW G
Major Havoc (rev 3) (Atari, 1983) · Supplement · 5 pages · 3 sections · original scan
£O0-252-05 a Ist printing
Supplement to TM-268, Ist printing
‘The Adventures of SOR
Installation Instructions
This supplement documents the encoder wheel for the converted Major Havoc game. The exploded illustration of the encoder wheel assembly is on page 2, the parts list for the encoder wheel is on page 3, and the maintenance procedure for the encoder wheel is on page 4. The encoder wheel assembly is designed for maximum performance with minimum maintenance. To maintain this control, put two drops of a lightweight machine oil on each bearing once every six months. Please refer to page 4 for this procedure.
A.
ATARI
(D2 tere Commmnnone Coneary
Pe eee tes
st printing
Figure 1 Encoder Wheel Assembly A038023-01 A
oh ace eteteertenata ete teen ete Tee TS
. 1st printing
Encoder Wheel Assembly Parts List eee Part No. Description 0352209 -O3 Coupler PCB Assembly 72-JB3606 #6 x %-Inch Plastite Screw 038010-01 Encoder Wheel 038011-01 Encoder Wheel Plug -ner a 038022-01 Flange Bearing 038026-01 Encoder Wheel Housing 038319-01 Encoder Whee! Knob 178012-005 0.156-inch Diameter Shaft Retaining Clip ——_—__-———— _- rr eee
‘ Encoder Wheel
Maintenance
Unplug the game before you begin the following maintenance procedure.
Service Items Required ___* #2 Philips-head screwdriver sear eS ® Flat-tipped screwdriver © ¥%-Inch hex driver ® Lightweight machine oil (Atari part no. 107013-001)
Open the Control Panel
- Unlock and open the coin door. 2 Reach inside the coin door and up to the top of the contro! panel.
- Open the rwo spring-draw latches located at the bottom of the display shield.
- Close and lock the coin door. §. Lift the top edge of the contro! panel and tilt it toward you.
Remove the Encoder Wheel Assembly From the Control Panel
- Disconnect the 4-pin harness from the Coupler printedcircuit board (PCB).
- Usea flat-tipped screwdriver to pry the retaining clip off of the shaft of the knob. Save this retaining clip for reassembly. 3.. Remove the encoder wheel knob by pulling it out of the assembly.
- Usea%-inch hex driver to loosen the nuts securing the encoder wheel to the control panel.
- Remove the carriage bolts, nuts, and wasi,'".s. Save this hardware for reassembly.
Open the Encoder Wheel Housing 1, Two identical parts snap together to form the housing for the encoder wheel. To unsnap these two parts, place two fingertips on the tabs that protrude on one end of the housing. Pull these tabs firmly away from the center of the housing, until they release. Turn the oy housing over and place two fingertips on the tabs that protrude on the other end of the housing. Pull these tabs firmly away from the center of the housing until they release.
- Separate the two parts that form the housing.
- Use the Phillips-head screwdriver to remove the screws that attach the Coupler PCB to the housing. Carefully remove the Coupler PCB. Lubricate the Bearings _ =e =
- - Lift the encoder wheel out of the housing.
- Make sure the plugs are evenly spaced. if they are not, poke them out from the back, and reposition them.
- There are identical bearings on either side of the encoder wheel. Remove cach of these bearings by sliding them off of the shaft. Apply two drops of a lightweight machine oil to the inside of each bearing.
Reassemble the Encoder Wheel Housing
- Notice that each bearing has a key. This key is designed to fit inside the groove near the center hole of each housing. Place a bearing in each half of the housing Making sure that the keys fit in the grooves. Place the encoder wheel inside a housing.
- Place the empty housing on top of the housing that contains the encoder wheel. The housings should be a mirror image of each other. Firmly snap both housings together.
- UseaPhillips-head screwdriver to reattach the Coupler PCB to the housing. (The screws go in the large holes on the Coupler PCB, and the encoder wheel should be abie to spin freely between the sections of the black coupler.)
Attach the Encoder Wheel Assembly To the Control Panel
- Place the encoder wheel housing against the contro! panel, with the coupler PCB away from the panel.
- Insert each carriage bolt through the control panel, the encoder wheel housing, a washer, and 2 nut.
- Use a %-inch hex driver to tighten these nuts.
- Connect the 4-pin harness to the Coupler printedcircuit board (PCB).
- From the player side of the control panel, insert the encoder wheel knob into the housing,
- Place the retaining clip on the shaft of the encoder knob, in the groove closest to the housing.
Close the Control Panel 1, Unlock and open the coin door.
- Close the control panel.
- Reach inside the coin door and up to the top of the control panel.
- Close the two spring-draw latches located'at the bottom of the display shield.
- Close anc lock the coin door.
the green ground wire is firmly attachedto the metal tab on the inside of the control pane!. Only then should
Figure 2. Disassembling the Encoder Wheel
ee a Qn RT IDE ARR Se eee tm a®